* [PATCH 1/3] ARM: dts: imx28: Fix label name for L2 switch
@ 2020-11-25 16:18 Lukasz Majewski
2020-11-25 16:18 ` [PATCH 2/3] ARM: dts: imx28: add pinmux for USB1 overcurrent on pwm2 Lukasz Majewski
` (2 more replies)
0 siblings, 3 replies; 8+ messages in thread
From: Lukasz Majewski @ 2020-11-25 16:18 UTC (permalink / raw)
To: Rob Herring, Shawn Guo, Fabio Estevam
Cc: Sascha Hauer, Pengutronix Kernel Team, NXP Linux Team,
devicetree, linux-arm-kernel, linux-kernel, Lukasz Majewski
The 'eth_switch' name has been misspelled in the imx28.dtsi file,
so this change fixes it.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
---
arch/arm/boot/dts/imx28.dtsi | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/imx28.dtsi b/arch/arm/boot/dts/imx28.dtsi
index a2b799c56f8f..6e7531b64bf7 100644
--- a/arch/arm/boot/dts/imx28.dtsi
+++ b/arch/arm/boot/dts/imx28.dtsi
@@ -1317,7 +1317,7 @@
status = "disabled";
};
- etn_switch: switch@800f8000 {
+ eth_switch: switch@800f8000 {
reg = <0x800f8000 0x8000>;
status = "disabled";
};
--
2.20.1
^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH 2/3] ARM: dts: imx28: add pinmux for USB1 overcurrent on pwm2
2020-11-25 16:18 [PATCH 1/3] ARM: dts: imx28: Fix label name for L2 switch Lukasz Majewski
@ 2020-11-25 16:18 ` Lukasz Majewski
2020-12-01 1:43 ` Shawn Guo
2020-11-25 16:18 ` [PATCH 3/3] ARM: dts: imx28: Add DTS description of imx28 based XEA board Lukasz Majewski
2020-12-01 1:42 ` [PATCH 1/3] ARM: dts: imx28: Fix label name for L2 switch Shawn Guo
2 siblings, 1 reply; 8+ messages in thread
From: Lukasz Majewski @ 2020-11-25 16:18 UTC (permalink / raw)
To: Rob Herring, Shawn Guo, Fabio Estevam
Cc: Sascha Hauer, Pengutronix Kernel Team, NXP Linux Team,
devicetree, linux-arm-kernel, linux-kernel, Mans Rullgard
From: Mans Rullgard <mans@mansr.com>
Add pinmux setting for USB1 overcurrent on pwm2 pad.
Signed-off-by: Mans Rullgard <mans@mansr.com>
---
arch/arm/boot/dts/imx28.dtsi | 10 ++++++++++
1 file changed, 10 insertions(+)
diff --git a/arch/arm/boot/dts/imx28.dtsi b/arch/arm/boot/dts/imx28.dtsi
index 6e7531b64bf7..6d24546f0abe 100644
--- a/arch/arm/boot/dts/imx28.dtsi
+++ b/arch/arm/boot/dts/imx28.dtsi
@@ -948,6 +948,16 @@
fsl,pull-up = <MXS_PULL_DISABLE>;
};
+ usb1_pins_b: usb1@1 {
+ reg = <1>;
+ fsl,pinmux-ids = <
+ MX28_PAD_PWM2__USB1_OVERCURRENT
+ >;
+ fsl,drive-strength = <MXS_DRIVE_12mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
usb0_id_pins_a: usb0id@0 {
reg = <0>;
fsl,pinmux-ids = <
--
2.20.1
^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH 3/3] ARM: dts: imx28: Add DTS description of imx28 based XEA board
2020-11-25 16:18 [PATCH 1/3] ARM: dts: imx28: Fix label name for L2 switch Lukasz Majewski
2020-11-25 16:18 ` [PATCH 2/3] ARM: dts: imx28: add pinmux for USB1 overcurrent on pwm2 Lukasz Majewski
@ 2020-11-25 16:18 ` Lukasz Majewski
2020-12-09 22:11 ` Lukasz Majewski
2020-12-22 17:58 ` Fabio Estevam
2020-12-01 1:42 ` [PATCH 1/3] ARM: dts: imx28: Fix label name for L2 switch Shawn Guo
2 siblings, 2 replies; 8+ messages in thread
From: Lukasz Majewski @ 2020-11-25 16:18 UTC (permalink / raw)
To: Rob Herring, Shawn Guo, Fabio Estevam
Cc: Sascha Hauer, Pengutronix Kernel Team, NXP Linux Team,
devicetree, linux-arm-kernel, linux-kernel, Lukasz Majewski
This patch adds DTS definition of the imx278 based XEA board.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
---
arch/arm/boot/dts/Makefile | 3 +-
arch/arm/boot/dts/imx28-lwe.dtsi | 185 +++++++++++++++++++++++++++++++
arch/arm/boot/dts/imx28-xea.dts | 99 +++++++++++++++++
3 files changed, 286 insertions(+), 1 deletion(-)
create mode 100644 arch/arm/boot/dts/imx28-lwe.dtsi
create mode 100644 arch/arm/boot/dts/imx28-xea.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 4572db3fa5ae..c7c95ddc648b 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -702,7 +702,8 @@ dtb-$(CONFIG_ARCH_MXS) += \
imx28-m28evk.dtb \
imx28-sps1.dtb \
imx28-ts4600.dtb \
- imx28-tx28.dtb
+ imx28-tx28.dtb \
+ imx28-xea.dtb
dtb-$(CONFIG_ARCH_NOMADIK) += \
ste-nomadik-s8815.dtb \
ste-nomadik-nhk15.dtb
diff --git a/arch/arm/boot/dts/imx28-lwe.dtsi b/arch/arm/boot/dts/imx28-lwe.dtsi
new file mode 100644
index 000000000000..cb2eb4377d9c
--- /dev/null
+++ b/arch/arm/boot/dts/imx28-lwe.dtsi
@@ -0,0 +1,185 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2020
+ * Lukasz Majewski, DENX Software Engineering, lukma@denx.de
+ */
+
+/dts-v1/;
+#include "imx28.dtsi"
+
+/ {
+ compatible = "fsl,imx28";
+
+ aliases {
+ spi2 = &ssp3;
+ };
+
+ chosen {
+ bootargs = "root=/dev/mmcblk0p2 rootfstype=ext4 ro rootwait console=ttyAMA0,115200 panic=1";
+ };
+
+ memory {
+ reg = <0x40000000 0x08000000>;
+ };
+
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reg_3v3: regulator@0 {
+ compatible = "regulator-fixed";
+ reg = <0>;
+ regulator-name = "3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reg_usb_5v: regulator@1 {
+ compatible = "regulator-fixed";
+ reg = <1>;
+ regulator-name = "usb_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ };
+
+ reg_fec_3v3: regulator@2 {
+ compatible = "regulator-fixed";
+ reg = <2>;
+ regulator-name = "fec-phy";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ enable-active-high;
+ regulator-boot-on;
+ };
+ };
+};
+
+&duart {
+ pinctrl-names = "default";
+ pinctrl-0 = <&duart_pins_a>;
+ status = "okay";
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+};
+
+&saif0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&saif0_pins_a>;
+ #sound-dai-cells = <0>;
+ assigned-clocks = <&clks 53>;
+ assigned-clock-rates = <12000000>;
+ status = "okay";
+};
+
+&saif1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&saif1_pins_a>;
+ fsl,saif-master = <&saif0>;
+ #sound-dai-cells = <0>;
+ status = "okay";
+};
+
+&spi3_pins_a {
+ fsl,pinmux-ids = <
+ MX28_PAD_AUART2_RX__SSP3_D4
+ MX28_PAD_AUART2_TX__SSP3_D5
+ MX28_PAD_SSP3_SCK__SSP3_SCK
+ MX28_PAD_SSP3_MOSI__SSP3_CMD
+ MX28_PAD_SSP3_MISO__SSP3_D0
+ MX28_PAD_SSP3_SS0__SSP3_D3
+ MX28_PAD_AUART2_TX__GPIO_3_9
+ >;
+};
+
+&ssp3 {
+ compatible = "fsl,imx28-spi";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi3_pins_a>;
+ status = "okay";
+
+ flash0: s25fl256s0@0 {
+ compatible = "s25fl256s1", "jedec,spi-nor";
+ spi-max-frequency = <40000000>;
+ reg = <0>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0 0x80000>;
+ read-only;
+ };
+
+ partition@80000 {
+ label = "env0";
+ reg = <0x80000 0x10000>;
+ };
+
+ partition@90000 {
+ label = "env1";
+ reg = <0x90000 0x10000>;
+ };
+
+ partition@100000 {
+ label = "kernel";
+ reg = <0x100000 0x400000>;
+ };
+
+ partition@500000 {
+ label = "swupdate";
+ reg = <0x500000 0x800000>;
+ };
+ };
+ };
+};
+
+&ssp2 {
+ compatible = "fsl,imx28-spi";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi2_pins_a>;
+ status = "okay";
+};
+
+&ssp0 {
+ compatible = "fsl,imx28-mmc";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_8bit_pins_a>;
+ bus-width = <8>;
+ vmmc-supply = <®_3v3>;
+ non-removable;
+ status = "okay";
+};
+
+&usb0 {
+ vbus-supply = <®_usb_5v>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb0_pins_b>, <&usb0_id_pins_a>;
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usbphy0 {
+ status = "okay";
+};
+
+&usb1 {
+ vbus-supply = <®_usb_5v>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb1_pins_b>;
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usbphy1 {
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx28-xea.dts b/arch/arm/boot/dts/imx28-xea.dts
new file mode 100644
index 000000000000..672080485b78
--- /dev/null
+++ b/arch/arm/boot/dts/imx28-xea.dts
@@ -0,0 +1,99 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2020
+ * Lukasz Majewski, DENX Software Engineering, lukma@denx.de
+ */
+
+/dts-v1/;
+#include "imx28-lwe.dtsi"
+
+/ {
+ model = "XEA";
+};
+
+&can0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&can1_pins_a>;
+ status = "okay";
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins_b>;
+ status = "okay";
+};
+
+&pinctrl {
+ pinctrl-names = "default";
+ pinctrl-0 = <&hog_pins_a &hog_pins_tiva>;
+
+ hog_pins_a: hog@0 {
+ reg = <0>;
+ fsl,pinmux-ids = <
+ MX28_PAD_GPMI_D00__GPIO_0_0
+ MX28_PAD_GPMI_D02__GPIO_0_2
+ MX28_PAD_GPMI_D05__GPIO_0_5
+ MX28_PAD_GPMI_CE1N__GPIO_0_17
+ MX28_PAD_GPMI_RDY0__GPIO_0_20
+ MX28_PAD_GPMI_RDY1__GPIO_0_21
+ MX28_PAD_GPMI_RDY2__GPIO_0_22
+ MX28_PAD_GPMI_RDN__GPIO_0_24
+ MX28_PAD_GPMI_CLE__GPIO_0_27
+ MX28_PAD_LCD_VSYNC__GPIO_1_28
+ MX28_PAD_SSP1_SCK__GPIO_2_12
+ MX28_PAD_SSP1_CMD__GPIO_2_13
+ MX28_PAD_SSP2_SS1__GPIO_2_20
+ MX28_PAD_SSP2_SS2__GPIO_2_21
+ MX28_PAD_LCD_D00__GPIO_1_0
+ MX28_PAD_LCD_D01__GPIO_1_1
+ MX28_PAD_LCD_D02__GPIO_1_2
+ MX28_PAD_LCD_D03__GPIO_1_3
+ MX28_PAD_LCD_D04__GPIO_1_4
+ MX28_PAD_LCD_D05__GPIO_1_5
+ MX28_PAD_LCD_D06__GPIO_1_6
+ >;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ hog_pins_tiva: hog@1 {
+ reg = <1>;
+ fsl,pinmux-ids = <
+ MX28_PAD_GPMI_RDY3__GPIO_0_23
+ MX28_PAD_GPMI_WRN__GPIO_0_25
+ >;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+
+ hog_pins_coding: hog@2 {
+ reg = <2>;
+ fsl,pinmux-ids = <
+ MX28_PAD_GPMI_D01__GPIO_0_1
+ MX28_PAD_GPMI_D03__GPIO_0_3
+ MX28_PAD_GPMI_D04__GPIO_0_4
+ MX28_PAD_GPMI_D06__GPIO_0_6
+ MX28_PAD_GPMI_D07__GPIO_0_7
+ >;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
+ };
+};
+
+®_fec_3v3 {
+ gpio = <&gpio0 0 0>;
+};
+
+®_usb_5v {
+ gpio = <&gpio0 2 0>;
+};
+
+&spi2_pins_a {
+ fsl,pinmux-ids = <
+ MX28_PAD_SSP2_SCK__SSP2_SCK
+ MX28_PAD_SSP2_MOSI__SSP2_CMD
+ MX28_PAD_SSP2_MISO__SSP2_D0
+ MX28_PAD_SSP2_SS0__GPIO_2_19
+ >;
+};
--
2.20.1
^ permalink raw reply related [flat|nested] 8+ messages in thread
* Re: [PATCH 1/3] ARM: dts: imx28: Fix label name for L2 switch
2020-11-25 16:18 [PATCH 1/3] ARM: dts: imx28: Fix label name for L2 switch Lukasz Majewski
2020-11-25 16:18 ` [PATCH 2/3] ARM: dts: imx28: add pinmux for USB1 overcurrent on pwm2 Lukasz Majewski
2020-11-25 16:18 ` [PATCH 3/3] ARM: dts: imx28: Add DTS description of imx28 based XEA board Lukasz Majewski
@ 2020-12-01 1:42 ` Shawn Guo
2 siblings, 0 replies; 8+ messages in thread
From: Shawn Guo @ 2020-12-01 1:42 UTC (permalink / raw)
To: Lukasz Majewski
Cc: Rob Herring, Fabio Estevam, Sascha Hauer,
Pengutronix Kernel Team, NXP Linux Team, devicetree,
linux-arm-kernel, linux-kernel
On Wed, Nov 25, 2020 at 05:18:13PM +0100, Lukasz Majewski wrote:
> The 'eth_switch' name has been misspelled in the imx28.dtsi file,
> so this change fixes it.
>
> Signed-off-by: Lukasz Majewski <lukma@denx.de>
Applied, thanks.
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH 2/3] ARM: dts: imx28: add pinmux for USB1 overcurrent on pwm2
2020-11-25 16:18 ` [PATCH 2/3] ARM: dts: imx28: add pinmux for USB1 overcurrent on pwm2 Lukasz Majewski
@ 2020-12-01 1:43 ` Shawn Guo
0 siblings, 0 replies; 8+ messages in thread
From: Shawn Guo @ 2020-12-01 1:43 UTC (permalink / raw)
To: Lukasz Majewski
Cc: Rob Herring, Fabio Estevam, Sascha Hauer,
Pengutronix Kernel Team, NXP Linux Team, devicetree,
linux-arm-kernel, linux-kernel, Mans Rullgard
On Wed, Nov 25, 2020 at 05:18:14PM +0100, Lukasz Majewski wrote:
> From: Mans Rullgard <mans@mansr.com>
>
> Add pinmux setting for USB1 overcurrent on pwm2 pad.
>
> Signed-off-by: Mans Rullgard <mans@mansr.com>
Lukasz,
You need to add your SoB.
Shawn
> ---
> arch/arm/boot/dts/imx28.dtsi | 10 ++++++++++
> 1 file changed, 10 insertions(+)
>
> diff --git a/arch/arm/boot/dts/imx28.dtsi b/arch/arm/boot/dts/imx28.dtsi
> index 6e7531b64bf7..6d24546f0abe 100644
> --- a/arch/arm/boot/dts/imx28.dtsi
> +++ b/arch/arm/boot/dts/imx28.dtsi
> @@ -948,6 +948,16 @@
> fsl,pull-up = <MXS_PULL_DISABLE>;
> };
>
> + usb1_pins_b: usb1@1 {
> + reg = <1>;
> + fsl,pinmux-ids = <
> + MX28_PAD_PWM2__USB1_OVERCURRENT
> + >;
> + fsl,drive-strength = <MXS_DRIVE_12mA>;
> + fsl,voltage = <MXS_VOLTAGE_HIGH>;
> + fsl,pull-up = <MXS_PULL_DISABLE>;
> + };
> +
> usb0_id_pins_a: usb0id@0 {
> reg = <0>;
> fsl,pinmux-ids = <
> --
> 2.20.1
>
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH 3/3] ARM: dts: imx28: Add DTS description of imx28 based XEA board
2020-11-25 16:18 ` [PATCH 3/3] ARM: dts: imx28: Add DTS description of imx28 based XEA board Lukasz Majewski
@ 2020-12-09 22:11 ` Lukasz Majewski
2020-12-22 17:42 ` Lukasz Majewski
2020-12-22 17:58 ` Fabio Estevam
1 sibling, 1 reply; 8+ messages in thread
From: Lukasz Majewski @ 2020-12-09 22:11 UTC (permalink / raw)
To: Rob Herring, Shawn Guo, Fabio Estevam
Cc: Sascha Hauer, Pengutronix Kernel Team, NXP Linux Team,
devicetree, linux-arm-kernel, linux-kernel
[-- Attachment #1: Type: text/plain, Size: 8192 bytes --]
Dear Community,
> This patch adds DTS definition of the imx278 based XEA board.
>
> Signed-off-by: Lukasz Majewski <lukma@denx.de>
> ---
> arch/arm/boot/dts/Makefile | 3 +-
> arch/arm/boot/dts/imx28-lwe.dtsi | 185
> +++++++++++++++++++++++++++++++ arch/arm/boot/dts/imx28-xea.dts |
> 99 +++++++++++++++++ 3 files changed, 286 insertions(+), 1 deletion(-)
> create mode 100644 arch/arm/boot/dts/imx28-lwe.dtsi
> create mode 100644 arch/arm/boot/dts/imx28-xea.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 4572db3fa5ae..c7c95ddc648b 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -702,7 +702,8 @@ dtb-$(CONFIG_ARCH_MXS) += \
> imx28-m28evk.dtb \
> imx28-sps1.dtb \
> imx28-ts4600.dtb \
> - imx28-tx28.dtb
> + imx28-tx28.dtb \
> + imx28-xea.dtb
> dtb-$(CONFIG_ARCH_NOMADIK) += \
> ste-nomadik-s8815.dtb \
> ste-nomadik-nhk15.dtb
> diff --git a/arch/arm/boot/dts/imx28-lwe.dtsi
> b/arch/arm/boot/dts/imx28-lwe.dtsi new file mode 100644
> index 000000000000..cb2eb4377d9c
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx28-lwe.dtsi
> @@ -0,0 +1,185 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> +/*
> + * Copyright 2020
> + * Lukasz Majewski, DENX Software Engineering, lukma@denx.de
> + */
> +
> +/dts-v1/;
> +#include "imx28.dtsi"
> +
> +/ {
> + compatible = "fsl,imx28";
> +
> + aliases {
> + spi2 = &ssp3;
> + };
> +
> + chosen {
> + bootargs = "root=/dev/mmcblk0p2 rootfstype=ext4 ro
> rootwait console=ttyAMA0,115200 panic=1";
> + };
> +
> + memory {
> + reg = <0x40000000 0x08000000>;
> + };
> +
> + regulators {
> + compatible = "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + reg_3v3: regulator@0 {
> + compatible = "regulator-fixed";
> + reg = <0>;
> + regulator-name = "3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> +
> + reg_usb_5v: regulator@1 {
> + compatible = "regulator-fixed";
> + reg = <1>;
> + regulator-name = "usb_vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + enable-active-high;
> + };
> +
> + reg_fec_3v3: regulator@2 {
> + compatible = "regulator-fixed";
> + reg = <2>;
> + regulator-name = "fec-phy";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + enable-active-high;
> + regulator-boot-on;
> + };
> + };
> +};
> +
> +&duart {
> + pinctrl-names = "default";
> + pinctrl-0 = <&duart_pins_a>;
> + status = "okay";
> +};
> +
> +&i2c0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c0_pins_a>;
> + status = "okay";
> +};
> +
> +&saif0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&saif0_pins_a>;
> + #sound-dai-cells = <0>;
> + assigned-clocks = <&clks 53>;
> + assigned-clock-rates = <12000000>;
> + status = "okay";
> +};
> +
> +&saif1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&saif1_pins_a>;
> + fsl,saif-master = <&saif0>;
> + #sound-dai-cells = <0>;
> + status = "okay";
> +};
> +
> +&spi3_pins_a {
> + fsl,pinmux-ids = <
> + MX28_PAD_AUART2_RX__SSP3_D4
> + MX28_PAD_AUART2_TX__SSP3_D5
> + MX28_PAD_SSP3_SCK__SSP3_SCK
> + MX28_PAD_SSP3_MOSI__SSP3_CMD
> + MX28_PAD_SSP3_MISO__SSP3_D0
> + MX28_PAD_SSP3_SS0__SSP3_D3
> + MX28_PAD_AUART2_TX__GPIO_3_9
> + >;
> +};
> +
> +&ssp3 {
> + compatible = "fsl,imx28-spi";
> + pinctrl-names = "default";
> + pinctrl-0 = <&spi3_pins_a>;
> + status = "okay";
> +
> + flash0: s25fl256s0@0 {
> + compatible = "s25fl256s1", "jedec,spi-nor";
> + spi-max-frequency = <40000000>;
> + reg = <0>;
> +
> + partitions {
> + compatible = "fixed-partitions";
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + partition@0 {
> + label = "u-boot";
> + reg = <0 0x80000>;
> + read-only;
> + };
> +
> + partition@80000 {
> + label = "env0";
> + reg = <0x80000 0x10000>;
> + };
> +
> + partition@90000 {
> + label = "env1";
> + reg = <0x90000 0x10000>;
> + };
> +
> + partition@100000 {
> + label = "kernel";
> + reg = <0x100000 0x400000>;
> + };
> +
> + partition@500000 {
> + label = "swupdate";
> + reg = <0x500000 0x800000>;
> + };
> + };
> + };
> +};
> +
> +&ssp2 {
> + compatible = "fsl,imx28-spi";
> + pinctrl-names = "default";
> + pinctrl-0 = <&spi2_pins_a>;
> + status = "okay";
> +};
> +
> +&ssp0 {
> + compatible = "fsl,imx28-mmc";
> + pinctrl-names = "default";
> + pinctrl-0 = <&mmc0_8bit_pins_a>;
> + bus-width = <8>;
> + vmmc-supply = <®_3v3>;
> + non-removable;
> + status = "okay";
> +};
> +
> +&usb0 {
> + vbus-supply = <®_usb_5v>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&usb0_pins_b>, <&usb0_id_pins_a>;
> + dr_mode = "host";
> + status = "okay";
> +};
> +
> +&usbphy0 {
> + status = "okay";
> +};
> +
> +&usb1 {
> + vbus-supply = <®_usb_5v>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&usb1_pins_b>;
> + dr_mode = "host";
> + status = "okay";
> +};
> +
> +&usbphy1 {
> + status = "okay";
> +};
> diff --git a/arch/arm/boot/dts/imx28-xea.dts
> b/arch/arm/boot/dts/imx28-xea.dts new file mode 100644
> index 000000000000..672080485b78
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx28-xea.dts
> @@ -0,0 +1,99 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> +/*
> + * Copyright 2020
> + * Lukasz Majewski, DENX Software Engineering, lukma@denx.de
> + */
> +
> +/dts-v1/;
> +#include "imx28-lwe.dtsi"
> +
> +/ {
> + model = "XEA";
> +};
> +
> +&can0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&can1_pins_a>;
> + status = "okay";
> +};
> +
> +&i2c1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c1_pins_b>;
> + status = "okay";
> +};
> +
> +&pinctrl {
> + pinctrl-names = "default";
> + pinctrl-0 = <&hog_pins_a &hog_pins_tiva>;
> +
> + hog_pins_a: hog@0 {
> + reg = <0>;
> + fsl,pinmux-ids = <
> + MX28_PAD_GPMI_D00__GPIO_0_0
> + MX28_PAD_GPMI_D02__GPIO_0_2
> + MX28_PAD_GPMI_D05__GPIO_0_5
> + MX28_PAD_GPMI_CE1N__GPIO_0_17
> + MX28_PAD_GPMI_RDY0__GPIO_0_20
> + MX28_PAD_GPMI_RDY1__GPIO_0_21
> + MX28_PAD_GPMI_RDY2__GPIO_0_22
> + MX28_PAD_GPMI_RDN__GPIO_0_24
> + MX28_PAD_GPMI_CLE__GPIO_0_27
> + MX28_PAD_LCD_VSYNC__GPIO_1_28
> + MX28_PAD_SSP1_SCK__GPIO_2_12
> + MX28_PAD_SSP1_CMD__GPIO_2_13
> + MX28_PAD_SSP2_SS1__GPIO_2_20
> + MX28_PAD_SSP2_SS2__GPIO_2_21
> + MX28_PAD_LCD_D00__GPIO_1_0
> + MX28_PAD_LCD_D01__GPIO_1_1
> + MX28_PAD_LCD_D02__GPIO_1_2
> + MX28_PAD_LCD_D03__GPIO_1_3
> + MX28_PAD_LCD_D04__GPIO_1_4
> + MX28_PAD_LCD_D05__GPIO_1_5
> + MX28_PAD_LCD_D06__GPIO_1_6
> + >;
> + fsl,drive-strength = <MXS_DRIVE_4mA>;
> + fsl,voltage = <MXS_VOLTAGE_HIGH>;
> + fsl,pull-up = <MXS_PULL_DISABLE>;
> + };
> +
> + hog_pins_tiva: hog@1 {
> + reg = <1>;
> + fsl,pinmux-ids = <
> + MX28_PAD_GPMI_RDY3__GPIO_0_23
> + MX28_PAD_GPMI_WRN__GPIO_0_25
> + >;
> + fsl,voltage = <MXS_VOLTAGE_HIGH>;
> + fsl,pull-up = <MXS_PULL_DISABLE>;
> + };
> +
> + hog_pins_coding: hog@2 {
> + reg = <2>;
> + fsl,pinmux-ids = <
> + MX28_PAD_GPMI_D01__GPIO_0_1
> + MX28_PAD_GPMI_D03__GPIO_0_3
> + MX28_PAD_GPMI_D04__GPIO_0_4
> + MX28_PAD_GPMI_D06__GPIO_0_6
> + MX28_PAD_GPMI_D07__GPIO_0_7
> + >;
> + fsl,voltage = <MXS_VOLTAGE_HIGH>;
> + fsl,pull-up = <MXS_PULL_DISABLE>;
> + };
> +};
> +
> +®_fec_3v3 {
> + gpio = <&gpio0 0 0>;
> +};
> +
> +®_usb_5v {
> + gpio = <&gpio0 2 0>;
> +};
> +
> +&spi2_pins_a {
> + fsl,pinmux-ids = <
> + MX28_PAD_SSP2_SCK__SSP2_SCK
> + MX28_PAD_SSP2_MOSI__SSP2_CMD
> + MX28_PAD_SSP2_MISO__SSP2_D0
> + MX28_PAD_SSP2_SS0__GPIO_2_19
> + >;
> +};
Gentle ping on this patch.
Best regards,
Lukasz Majewski
--
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-59 Fax: (+49)-8142-66989-80 Email: lukma@denx.de
[-- Attachment #2: OpenPGP digital signature --]
[-- Type: application/pgp-signature, Size: 488 bytes --]
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH 3/3] ARM: dts: imx28: Add DTS description of imx28 based XEA board
2020-12-09 22:11 ` Lukasz Majewski
@ 2020-12-22 17:42 ` Lukasz Majewski
0 siblings, 0 replies; 8+ messages in thread
From: Lukasz Majewski @ 2020-12-22 17:42 UTC (permalink / raw)
To: Rob Herring, Shawn Guo, Fabio Estevam
Cc: Sascha Hauer, Pengutronix Kernel Team, NXP Linux Team,
devicetree, linux-arm-kernel, linux-kernel
[-- Attachment #1: Type: text/plain, Size: 9218 bytes --]
Hi Shawn,
> Dear Community,
>
> > This patch adds DTS definition of the imx278 based XEA board.
> >
> > Signed-off-by: Lukasz Majewski <lukma@denx.de>
> > ---
> > arch/arm/boot/dts/Makefile | 3 +-
> > arch/arm/boot/dts/imx28-lwe.dtsi | 185
> > +++++++++++++++++++++++++++++++ arch/arm/boot/dts/imx28-xea.dts |
> > 99 +++++++++++++++++ 3 files changed, 286 insertions(+), 1
> > deletion(-) create mode 100644 arch/arm/boot/dts/imx28-lwe.dtsi
> > create mode 100644 arch/arm/boot/dts/imx28-xea.dts
> >
> > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> > index 4572db3fa5ae..c7c95ddc648b 100644
> > --- a/arch/arm/boot/dts/Makefile
> > +++ b/arch/arm/boot/dts/Makefile
> > @@ -702,7 +702,8 @@ dtb-$(CONFIG_ARCH_MXS) += \
> > imx28-m28evk.dtb \
> > imx28-sps1.dtb \
> > imx28-ts4600.dtb \
> > - imx28-tx28.dtb
> > + imx28-tx28.dtb \
> > + imx28-xea.dtb
> > dtb-$(CONFIG_ARCH_NOMADIK) += \
> > ste-nomadik-s8815.dtb \
> > ste-nomadik-nhk15.dtb
> > diff --git a/arch/arm/boot/dts/imx28-lwe.dtsi
> > b/arch/arm/boot/dts/imx28-lwe.dtsi new file mode 100644
> > index 000000000000..cb2eb4377d9c
> > --- /dev/null
> > +++ b/arch/arm/boot/dts/imx28-lwe.dtsi
> > @@ -0,0 +1,185 @@
> > +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> > +/*
> > + * Copyright 2020
> > + * Lukasz Majewski, DENX Software Engineering, lukma@denx.de
> > + */
> > +
> > +/dts-v1/;
> > +#include "imx28.dtsi"
> > +
> > +/ {
> > + compatible = "fsl,imx28";
> > +
> > + aliases {
> > + spi2 = &ssp3;
> > + };
> > +
> > + chosen {
> > + bootargs = "root=/dev/mmcblk0p2 rootfstype=ext4 ro
> > rootwait console=ttyAMA0,115200 panic=1";
> > + };
> > +
> > + memory {
> > + reg = <0x40000000 0x08000000>;
> > + };
> > +
> > + regulators {
> > + compatible = "simple-bus";
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + reg_3v3: regulator@0 {
> > + compatible = "regulator-fixed";
> > + reg = <0>;
> > + regulator-name = "3V3";
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-always-on;
> > + };
> > +
> > + reg_usb_5v: regulator@1 {
> > + compatible = "regulator-fixed";
> > + reg = <1>;
> > + regulator-name = "usb_vbus";
> > + regulator-min-microvolt = <5000000>;
> > + regulator-max-microvolt = <5000000>;
> > + enable-active-high;
> > + };
> > +
> > + reg_fec_3v3: regulator@2 {
> > + compatible = "regulator-fixed";
> > + reg = <2>;
> > + regulator-name = "fec-phy";
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + enable-active-high;
> > + regulator-boot-on;
> > + };
> > + };
> > +};
> > +
> > +&duart {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&duart_pins_a>;
> > + status = "okay";
> > +};
> > +
> > +&i2c0 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&i2c0_pins_a>;
> > + status = "okay";
> > +};
> > +
> > +&saif0 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&saif0_pins_a>;
> > + #sound-dai-cells = <0>;
> > + assigned-clocks = <&clks 53>;
> > + assigned-clock-rates = <12000000>;
> > + status = "okay";
> > +};
> > +
> > +&saif1 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&saif1_pins_a>;
> > + fsl,saif-master = <&saif0>;
> > + #sound-dai-cells = <0>;
> > + status = "okay";
> > +};
> > +
> > +&spi3_pins_a {
> > + fsl,pinmux-ids = <
> > + MX28_PAD_AUART2_RX__SSP3_D4
> > + MX28_PAD_AUART2_TX__SSP3_D5
> > + MX28_PAD_SSP3_SCK__SSP3_SCK
> > + MX28_PAD_SSP3_MOSI__SSP3_CMD
> > + MX28_PAD_SSP3_MISO__SSP3_D0
> > + MX28_PAD_SSP3_SS0__SSP3_D3
> > + MX28_PAD_AUART2_TX__GPIO_3_9
> > + >;
> > +};
> > +
> > +&ssp3 {
> > + compatible = "fsl,imx28-spi";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&spi3_pins_a>;
> > + status = "okay";
> > +
> > + flash0: s25fl256s0@0 {
> > + compatible = "s25fl256s1", "jedec,spi-nor";
> > + spi-max-frequency = <40000000>;
> > + reg = <0>;
> > +
> > + partitions {
> > + compatible = "fixed-partitions";
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > +
> > + partition@0 {
> > + label = "u-boot";
> > + reg = <0 0x80000>;
> > + read-only;
> > + };
> > +
> > + partition@80000 {
> > + label = "env0";
> > + reg = <0x80000 0x10000>;
> > + };
> > +
> > + partition@90000 {
> > + label = "env1";
> > + reg = <0x90000 0x10000>;
> > + };
> > +
> > + partition@100000 {
> > + label = "kernel";
> > + reg = <0x100000 0x400000>;
> > + };
> > +
> > + partition@500000 {
> > + label = "swupdate";
> > + reg = <0x500000 0x800000>;
> > + };
> > + };
> > + };
> > +};
> > +
> > +&ssp2 {
> > + compatible = "fsl,imx28-spi";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&spi2_pins_a>;
> > + status = "okay";
> > +};
> > +
> > +&ssp0 {
> > + compatible = "fsl,imx28-mmc";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&mmc0_8bit_pins_a>;
> > + bus-width = <8>;
> > + vmmc-supply = <®_3v3>;
> > + non-removable;
> > + status = "okay";
> > +};
> > +
> > +&usb0 {
> > + vbus-supply = <®_usb_5v>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&usb0_pins_b>, <&usb0_id_pins_a>;
> > + dr_mode = "host";
> > + status = "okay";
> > +};
> > +
> > +&usbphy0 {
> > + status = "okay";
> > +};
> > +
> > +&usb1 {
> > + vbus-supply = <®_usb_5v>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&usb1_pins_b>;
> > + dr_mode = "host";
> > + status = "okay";
> > +};
> > +
> > +&usbphy1 {
> > + status = "okay";
> > +};
> > diff --git a/arch/arm/boot/dts/imx28-xea.dts
> > b/arch/arm/boot/dts/imx28-xea.dts new file mode 100644
> > index 000000000000..672080485b78
> > --- /dev/null
> > +++ b/arch/arm/boot/dts/imx28-xea.dts
> > @@ -0,0 +1,99 @@
> > +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> > +/*
> > + * Copyright 2020
> > + * Lukasz Majewski, DENX Software Engineering, lukma@denx.de
> > + */
> > +
> > +/dts-v1/;
> > +#include "imx28-lwe.dtsi"
> > +
> > +/ {
> > + model = "XEA";
> > +};
> > +
> > +&can0 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&can1_pins_a>;
> > + status = "okay";
> > +};
> > +
> > +&i2c1 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&i2c1_pins_b>;
> > + status = "okay";
> > +};
> > +
> > +&pinctrl {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&hog_pins_a &hog_pins_tiva>;
> > +
> > + hog_pins_a: hog@0 {
> > + reg = <0>;
> > + fsl,pinmux-ids = <
> > + MX28_PAD_GPMI_D00__GPIO_0_0
> > + MX28_PAD_GPMI_D02__GPIO_0_2
> > + MX28_PAD_GPMI_D05__GPIO_0_5
> > + MX28_PAD_GPMI_CE1N__GPIO_0_17
> > + MX28_PAD_GPMI_RDY0__GPIO_0_20
> > + MX28_PAD_GPMI_RDY1__GPIO_0_21
> > + MX28_PAD_GPMI_RDY2__GPIO_0_22
> > + MX28_PAD_GPMI_RDN__GPIO_0_24
> > + MX28_PAD_GPMI_CLE__GPIO_0_27
> > + MX28_PAD_LCD_VSYNC__GPIO_1_28
> > + MX28_PAD_SSP1_SCK__GPIO_2_12
> > + MX28_PAD_SSP1_CMD__GPIO_2_13
> > + MX28_PAD_SSP2_SS1__GPIO_2_20
> > + MX28_PAD_SSP2_SS2__GPIO_2_21
> > + MX28_PAD_LCD_D00__GPIO_1_0
> > + MX28_PAD_LCD_D01__GPIO_1_1
> > + MX28_PAD_LCD_D02__GPIO_1_2
> > + MX28_PAD_LCD_D03__GPIO_1_3
> > + MX28_PAD_LCD_D04__GPIO_1_4
> > + MX28_PAD_LCD_D05__GPIO_1_5
> > + MX28_PAD_LCD_D06__GPIO_1_6
> > + >;
> > + fsl,drive-strength = <MXS_DRIVE_4mA>;
> > + fsl,voltage = <MXS_VOLTAGE_HIGH>;
> > + fsl,pull-up = <MXS_PULL_DISABLE>;
> > + };
> > +
> > + hog_pins_tiva: hog@1 {
> > + reg = <1>;
> > + fsl,pinmux-ids = <
> > + MX28_PAD_GPMI_RDY3__GPIO_0_23
> > + MX28_PAD_GPMI_WRN__GPIO_0_25
> > + >;
> > + fsl,voltage = <MXS_VOLTAGE_HIGH>;
> > + fsl,pull-up = <MXS_PULL_DISABLE>;
> > + };
> > +
> > + hog_pins_coding: hog@2 {
> > + reg = <2>;
> > + fsl,pinmux-ids = <
> > + MX28_PAD_GPMI_D01__GPIO_0_1
> > + MX28_PAD_GPMI_D03__GPIO_0_3
> > + MX28_PAD_GPMI_D04__GPIO_0_4
> > + MX28_PAD_GPMI_D06__GPIO_0_6
> > + MX28_PAD_GPMI_D07__GPIO_0_7
> > + >;
> > + fsl,voltage = <MXS_VOLTAGE_HIGH>;
> > + fsl,pull-up = <MXS_PULL_DISABLE>;
> > + };
> > +};
> > +
> > +®_fec_3v3 {
> > + gpio = <&gpio0 0 0>;
> > +};
> > +
> > +®_usb_5v {
> > + gpio = <&gpio0 2 0>;
> > +};
> > +
> > +&spi2_pins_a {
> > + fsl,pinmux-ids = <
> > + MX28_PAD_SSP2_SCK__SSP2_SCK
> > + MX28_PAD_SSP2_MOSI__SSP2_CMD
> > + MX28_PAD_SSP2_MISO__SSP2_D0
> > + MX28_PAD_SSP2_SS0__GPIO_2_19
> > + >;
> > +};
>
> Gentle ping on this patch.
Gentle ping on this patch. Are there any comments regarding it?
>
>
> Best regards,
>
> Lukasz Majewski
>
> --
>
> DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
> HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
> Phone: (+49)-8142-66989-59 Fax: (+49)-8142-66989-80 Email:
> lukma@denx.de
Best regards,
Lukasz Majewski
--
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-59 Fax: (+49)-8142-66989-80 Email: lukma@denx.de
[-- Attachment #2: OpenPGP digital signature --]
[-- Type: application/pgp-signature, Size: 488 bytes --]
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH 3/3] ARM: dts: imx28: Add DTS description of imx28 based XEA board
2020-11-25 16:18 ` [PATCH 3/3] ARM: dts: imx28: Add DTS description of imx28 based XEA board Lukasz Majewski
2020-12-09 22:11 ` Lukasz Majewski
@ 2020-12-22 17:58 ` Fabio Estevam
1 sibling, 0 replies; 8+ messages in thread
From: Fabio Estevam @ 2020-12-22 17:58 UTC (permalink / raw)
To: Lukasz Majewski
Cc: Rob Herring, Shawn Guo, Sascha Hauer, Pengutronix Kernel Team,
NXP Linux Team,
open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
moderated list:ARM/FREESCALE IMX / MXC ARM ARCHITECTURE,
linux-kernel
Hi Lukasz,
On Wed, Nov 25, 2020 at 1:19 PM Lukasz Majewski <lukma@denx.de> wrote:
> diff --git a/arch/arm/boot/dts/imx28-lwe.dtsi b/arch/arm/boot/dts/imx28-lwe.dtsi
> new file mode 100644
> index 000000000000..cb2eb4377d9c
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx28-lwe.dtsi
> @@ -0,0 +1,185 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> +/*
> + * Copyright 2020
> + * Lukasz Majewski, DENX Software Engineering, lukma@denx.de
> + */
> +
> +/dts-v1/;
> +#include "imx28.dtsi"
> +
> +/ {
> + compatible = "fsl,imx28";
You can drop this one.
> +
> + aliases {
> + spi2 = &ssp3;
> + };
> +
> + chosen {
> + bootargs = "root=/dev/mmcblk0p2 rootfstype=ext4 ro rootwait console=ttyAMA0,115200 panic=1";
You could remove bootargs and let the bootloader pass it.
We usually don't pass bootargs in the i.MX dts files.
> + };
> +
> + memory {
memory@40000000
otherwise you will get dtc build warnings with W=1.
> + reg = <0x40000000 0x08000000>;
> + };
> +
> + regulators {
> + compatible = "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <0>;
No need for this 'regulators' container.
> +
> + reg_3v3: regulator@0 {
reg_3v3: regulator-reg-3v3 {
> + compatible = "regulator-fixed";
> + reg = <0>;
Remove the reg = <0>
Same applies to other regulators.
> + reg_usb_5v: regulator@1 {
> + compatible = "regulator-fixed";
> + reg = <1>;
> + regulator-name = "usb_vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + enable-active-high;
Why passing 'enable-active-high' when this is not gpio controlled?
> + };
> +
> + reg_fec_3v3: regulator@2 {
> + compatible = "regulator-fixed";
> + reg = <2>;
> + regulator-name = "fec-phy";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + enable-active-high;
Same here.
> +&ssp3 {
> + compatible = "fsl,imx28-spi";
> + pinctrl-names = "default";
> + pinctrl-0 = <&spi3_pins_a>;
> + status = "okay";
> +
> + flash0: s25fl256s0@0 {
Node names should be generic
flash@0
> +
> +/dts-v1/;
> +#include "imx28-lwe.dtsi"
> +
> +/ {
> + model = "XEA";
compatible = "xea,imx20-lwe", "fsl,imx28";
You should add xea to the vendor prefix in a separate patch.
You also need to add thie board to
Documentation/devicetree/bindings/arm/fsl.yaml
^ permalink raw reply [flat|nested] 8+ messages in thread
end of thread, other threads:[~2020-12-22 17:59 UTC | newest]
Thread overview: 8+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-11-25 16:18 [PATCH 1/3] ARM: dts: imx28: Fix label name for L2 switch Lukasz Majewski
2020-11-25 16:18 ` [PATCH 2/3] ARM: dts: imx28: add pinmux for USB1 overcurrent on pwm2 Lukasz Majewski
2020-12-01 1:43 ` Shawn Guo
2020-11-25 16:18 ` [PATCH 3/3] ARM: dts: imx28: Add DTS description of imx28 based XEA board Lukasz Majewski
2020-12-09 22:11 ` Lukasz Majewski
2020-12-22 17:42 ` Lukasz Majewski
2020-12-22 17:58 ` Fabio Estevam
2020-12-01 1:42 ` [PATCH 1/3] ARM: dts: imx28: Fix label name for L2 switch Shawn Guo
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).