Re: [PATCH v2 16/18] arm: dts: owl-s500-roseapplepi: Add uSD support

[Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>]

On Fri, Nov 20, 2020 at 01:56:10AM +0200, Cristian Ciocaltea wrote:
> Add uSD support for RoseapplePi SBC using a fixed regulator as a
> temporary solution until PMIC support becomes available.
> 
> Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
> ---
>  arch/arm/boot/dts/owl-s500-roseapplepi.dts | 50 ++++++++++++++++++++++
>  1 file changed, 50 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/owl-s500-roseapplepi.dts b/arch/arm/boot/dts/owl-s500-roseapplepi.dts
> index 800edf5d2d12..fe9ae3619422 100644
> --- a/arch/arm/boot/dts/owl-s500-roseapplepi.dts
> +++ b/arch/arm/boot/dts/owl-s500-roseapplepi.dts
> @@ -14,6 +14,7 @@ / {
>  	model = "Roseapple Pi";
>  
>  	aliases {
> +		mmc0 = &mmc0;
>  		serial2 = &uart2;
>  	};
>  
> @@ -25,6 +26,55 @@ memory@0 {
>  		device_type = "memory";
>  		reg = <0x0 0x80000000>; /* 2GB */
>  	};
> +
> +	/* Fixed regulator used in the absence of PMIC */
> +	sd_vcc: sd-vcc {

Is this the exact name in the schematics?

Thanks,
Mani

> +		compatible = "regulator-fixed";
> +		regulator-name = "fixed-3.1V";
> +		regulator-min-microvolt = <3100000>;
> +		regulator-max-microvolt = <3100000>;
> +		regulator-always-on;
> +	};
> +};
> +
> +&pinctrl {
> +	mmc0_pins: mmc0-pins {
> +		pinmux {
> +			groups = "sd0_d0_mfp", "sd0_d1_mfp", "sd0_d2_d3_mfp",
> +				 "sd0_cmd_mfp", "sd0_clk_mfp";
> +			function = "sd0";
> +		};
> +
> +		drv-pinconf {
> +			groups = "sd0_d0_d3_drv", "sd0_cmd_drv", "sd0_clk_drv";
> +			drive-strength = <8>;
> +		};
> +
> +		bias0-pinconf {
> +			pins = "sd0_d0", "sd0_d1", "sd0_d2",
> +			       "sd0_d3", "sd0_cmd";
> +			bias-pull-up;
> +		};
> +
> +		bias1-pinconf {
> +			pins = "sd0_clk";
> +			bias-pull-down;
> +		};
> +	};
> +};
> +
> +/* uSD */
> +&mmc0 {
> +	status = "okay";
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&mmc0_pins>;
> +	no-sdio;
> +	no-mmc;
> +	no-1-8-v;
> +	cd-gpios = <&pinctrl 117 GPIO_ACTIVE_LOW>;
> +	bus-width = <4>;
> +	vmmc-supply = <&sd_vcc>;
> +	vqmmc-supply = <&sd_vcc>;
>  };
>  
>  &twd_timer {
> -- 
> 2.29.2
>