linux-kernel.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Tony Lindgren <tony@atomide.com>
To: Amit Kucheria <amitk@kernel.org>,
	Daniel Lezcano <daniel.lezcano@linaro.org>,
	Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>,
	Keerthy <j-keerthy@ti.com>,
	linux-pm@vger.kernel.org, linux-kernel@vger.kernel.org,
	linux-omap@vger.kernel.org, Adam Ford <aford173@gmail.com>,
	Carl Philipp Klemm <philipp@uvos.xyz>,
	Merlijn Wajer <merlijn@wizzup.org>, Pavel Machek <pavel@ucw.cz>,
	Peter Ujfalusi <peter.ujfalusi@gmail.com>,
	Sebastian Reichel <sre@kernel.org>
Subject: [PATCH 1/3] thermal: ti-soc-thermal: Fix stuck sensor with continuous mode for 4430
Date: Wed, 30 Dec 2020 10:43:36 +0200	[thread overview]
Message-ID: <20201230084338.19410-1-tony@atomide.com> (raw)

At least for 4430, trying to use the single conversion mode eventually
hangs the thermal sensor. This can be quite easily seen with errors:

thermal thermal_zone0: failed to read out thermal zone (-5)

Also, trying to read the temperature shows a stuck value with:

$ while true; do cat /sys/class/thermal/thermal_zone0/temp; done

Where the temperature is not rising at all with the busy loop.

Additionally, the EOCZ (end of conversion) bit is not rising on 4430 in
single conversion mode while it works fine in continuous conversion mode.
It is also possible that the hung temperature sensor can affect the
thermal shutdown alert too.

Let's fix the issue by adding TI_BANDGAP_FEATURE_CONT_MODE_ONLY flag and
use it for 4430.

Note that we also need to add udelay to for the EOCZ (end of conversion)
bit polling as otherwise we have it time out too early on 4430. We'll be
changing the loop to use iopoll in the following clean-up patch.

Cc: Adam Ford <aford173@gmail.com>
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
 drivers/thermal/ti-soc-thermal/omap4-thermal-data.c | 3 ++-
 drivers/thermal/ti-soc-thermal/ti-bandgap.c         | 9 +++++++--
 drivers/thermal/ti-soc-thermal/ti-bandgap.h         | 2 ++
 3 files changed, 11 insertions(+), 3 deletions(-)

diff --git a/drivers/thermal/ti-soc-thermal/omap4-thermal-data.c b/drivers/thermal/ti-soc-thermal/omap4-thermal-data.c
--- a/drivers/thermal/ti-soc-thermal/omap4-thermal-data.c
+++ b/drivers/thermal/ti-soc-thermal/omap4-thermal-data.c
@@ -58,7 +58,8 @@ omap4430_adc_to_temp[OMAP4430_ADC_END_VALUE - OMAP4430_ADC_START_VALUE + 1] = {
 const struct ti_bandgap_data omap4430_data = {
 	.features = TI_BANDGAP_FEATURE_MODE_CONFIG |
 			TI_BANDGAP_FEATURE_CLK_CTRL |
-			TI_BANDGAP_FEATURE_POWER_SWITCH,
+			TI_BANDGAP_FEATURE_POWER_SWITCH |
+			TI_BANDGAP_FEATURE_CONT_MODE_ONLY,
 	.fclock_name = "bandgap_fclk",
 	.div_ck_name = "bandgap_fclk",
 	.conv_table = omap4430_adc_to_temp,
diff --git a/drivers/thermal/ti-soc-thermal/ti-bandgap.c b/drivers/thermal/ti-soc-thermal/ti-bandgap.c
--- a/drivers/thermal/ti-soc-thermal/ti-bandgap.c
+++ b/drivers/thermal/ti-soc-thermal/ti-bandgap.c
@@ -15,6 +15,7 @@
 #include <linux/kernel.h>
 #include <linux/interrupt.h>
 #include <linux/clk.h>
+#include <linux/delay.h>
 #include <linux/gpio/consumer.h>
 #include <linux/platform_device.h>
 #include <linux/err.h>
@@ -605,8 +606,10 @@ ti_bandgap_force_single_read(struct ti_bandgap *bgp, int id)
 	u32 counter = 1000;
 	struct temp_sensor_registers *tsr;
 
-	/* Select single conversion mode */
-	if (TI_BANDGAP_HAS(bgp, MODE_CONFIG))
+	/* Select continuous or single conversion mode */
+	if (TI_BANDGAP_HAS(bgp, CONT_MODE_ONLY))
+		RMW_BITS(bgp, id, bgap_mode_ctrl, mode_ctrl_mask, 1);
+	else if (TI_BANDGAP_HAS(bgp, MODE_CONFIG))
 		RMW_BITS(bgp, id, bgap_mode_ctrl, mode_ctrl_mask, 0);
 
 	/* Start of Conversion = 1 */
@@ -619,6 +622,7 @@ ti_bandgap_force_single_read(struct ti_bandgap *bgp, int id)
 		if (ti_bandgap_readl(bgp, tsr->temp_sensor_ctrl) &
 		    tsr->bgap_eocz_mask)
 			break;
+		udelay(1);
 	}
 
 	/* Start of Conversion = 0 */
@@ -630,6 +634,7 @@ ti_bandgap_force_single_read(struct ti_bandgap *bgp, int id)
 		if (!(ti_bandgap_readl(bgp, tsr->temp_sensor_ctrl) &
 		      tsr->bgap_eocz_mask))
 			break;
+		udelay(1);
 	}
 
 	return 0;
diff --git a/drivers/thermal/ti-soc-thermal/ti-bandgap.h b/drivers/thermal/ti-soc-thermal/ti-bandgap.h
--- a/drivers/thermal/ti-soc-thermal/ti-bandgap.h
+++ b/drivers/thermal/ti-soc-thermal/ti-bandgap.h
@@ -280,6 +280,7 @@ struct ti_temp_sensor {
  *	has Errata 814
  * TI_BANDGAP_FEATURE_UNRELIABLE - used when the sensor readings are too
  *	inaccurate.
+ * TI_BANDGAP_FEATURE_CONT_MODE_ONLY - used when single mode hangs the sensor
  * TI_BANDGAP_HAS(b, f) - macro to check if a bandgap device is capable of a
  *      specific feature (above) or not. Return non-zero, if yes.
  */
@@ -295,6 +296,7 @@ struct ti_temp_sensor {
 #define TI_BANDGAP_FEATURE_HISTORY_BUFFER	BIT(9)
 #define TI_BANDGAP_FEATURE_ERRATA_814		BIT(10)
 #define TI_BANDGAP_FEATURE_UNRELIABLE		BIT(11)
+#define TI_BANDGAP_FEATURE_CONT_MODE_ONLY	BIT(12)
 #define TI_BANDGAP_HAS(b, f)			\
 			((b)->conf->features & TI_BANDGAP_FEATURE_ ## f)
 
-- 
2.29.2

             reply	other threads:[~2020-12-30  8:44 UTC|newest]

Thread overview: 11+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2020-12-30  8:43 Tony Lindgren [this message]
2020-12-30  8:43 ` [PATCH 2/3] thermal: ti-soc-thermal: Simplify polling with iopoll Tony Lindgren
2020-12-30  8:43 ` [PATCH 3/3] thermal: ti-soc-thermal: Use non-inverted define for omap4 Tony Lindgren
2020-12-30 12:55 ` [PATCH 1/3] thermal: ti-soc-thermal: Fix stuck sensor with continuous mode for 4430 Adam Ford
2020-12-30 13:26   ` H. Nikolaus Schaller
2021-01-08  7:22     ` Tony Lindgren
2021-01-08 13:45       ` Adam Ford
2021-01-08 18:31         ` Adam Ford
2021-01-08 19:41           ` Adam Ford
2020-12-31 12:55 ` Péter Ujfalusi
2021-01-08  7:19   ` Tony Lindgren

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20201230084338.19410-1-tony@atomide.com \
    --to=tony@atomide.com \
    --cc=aford173@gmail.com \
    --cc=amitk@kernel.org \
    --cc=daniel.lezcano@linaro.org \
    --cc=edubezval@gmail.com \
    --cc=j-keerthy@ti.com \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-omap@vger.kernel.org \
    --cc=linux-pm@vger.kernel.org \
    --cc=merlijn@wizzup.org \
    --cc=pavel@ucw.cz \
    --cc=peter.ujfalusi@gmail.com \
    --cc=philipp@uvos.xyz \
    --cc=rui.zhang@intel.com \
    --cc=sre@kernel.org \
    --subject='Re: [PATCH 1/3] thermal: ti-soc-thermal: Fix stuck sensor with continuous mode for 4430' \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

This is a public inbox, see mirroring instructions
on how to clone and mirror all data and code used for this inbox