* [PATCH v3 0/2] J7200: Add support for higher speed modes in MMCSD subsystems
@ 2021-01-27 15:08 Aswath Govindraju
2021-01-27 15:08 ` [PATCH v3 1/2] dts: ti: k3-j7200-main: Add support for zeroth instance of GPIO subsystem Aswath Govindraju
2021-01-27 15:08 ` [PATCH v3 2/2] arm64: dts: ti: k3-j7200: Add support for higher speed modes in MMCSD subsystems Aswath Govindraju
0 siblings, 2 replies; 10+ messages in thread
From: Aswath Govindraju @ 2021-01-27 15:08 UTC (permalink / raw)
Cc: Vignesh Raghavendra, Lokesh Vutla, Kishon Vijay Abraham I,
Faiz Abbas, Aswath Govindraju, Nishanth Menon, Tero Kristo,
Rob Herring, linux-arm-kernel, devicetree, linux-kernel
The following series of patches
- Add support for the zeroth instance of GPIO subsystem in the main domain
- Add voltage regulator device tree nodes and their corresponding pinmux
to support power cycle and voltage switch required for UHS-I modes
- sets respective tags in sdhci0 node to support higher speeds
- remove no-1-8-v tag from sdhci1 node to support UHS-I modes
Changes since v2:
- Added main_gpio0 DT node
- Added voltage regulator device tree nodes required to support UHS-I modes
Changes since v1:
- squashed the two patches into one
- added performance logs for the above mentioned speed modes
Aswath Govindraju (2):
dts: ti: k3-j7200-main: Add support for zeroth instance of GPIO subsystem
arm64: dts: ti: k3-j7200: Add support for higher speed modes in MMCSD
subsystems
.../dts/ti/k3-j7200-common-proc-board.dts | 31 +++++++++++++++++++
arch/arm64/boot/dts/ti/k3-j7200-main.dtsi | 20 +++++++++++-
2 files changed, 50 insertions(+), 1 deletion(-)
--
2.17.1
^ permalink raw reply [flat|nested] 10+ messages in thread* [PATCH v3 1/2] dts: ti: k3-j7200-main: Add support for zeroth instance of GPIO subsystem 2021-01-27 15:08 [PATCH v3 0/2] J7200: Add support for higher speed modes in MMCSD subsystems Aswath Govindraju @ 2021-01-27 15:08 ` Aswath Govindraju 2021-01-27 15:12 ` Nishanth Menon 2021-01-27 15:08 ` [PATCH v3 2/2] arm64: dts: ti: k3-j7200: Add support for higher speed modes in MMCSD subsystems Aswath Govindraju 1 sibling, 1 reply; 10+ messages in thread From: Aswath Govindraju @ 2021-01-27 15:08 UTC (permalink / raw) Cc: Vignesh Raghavendra, Lokesh Vutla, Kishon Vijay Abraham I, Faiz Abbas, Aswath Govindraju, Nishanth Menon, Tero Kristo, Rob Herring, linux-arm-kernel, devicetree, linux-kernel Add support for the zeroth instance of GPIO subsystem in the main domain. Signed-off-by: Aswath Govindraju <a-govindraju@ti.com> --- arch/arm64/boot/dts/ti/k3-j7200-main.dtsi | 17 +++++++++++++++++ 1 file changed, 17 insertions(+) diff --git a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi index 4cc2e9094d0e..75dffbb26d52 100644 --- a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi +++ b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi @@ -294,6 +294,23 @@ pinctrl-single,function-mask = <0xffffffff>; }; + main_gpio0: gpio@600000 { + compatible = "ti,j721e-gpio", "ti,keystone-gpio"; + reg = <0x0 0x00600000 0x0 0x100>; + gpio-controller; + #gpio-cells = <2>; + interrupt-parent = <&main_gpio_intr>; + interrupts = <145>, <146>, <147>, <148>, + <149>; + interrupt-controller; + #interrupt-cells = <2>; + ti,ngpio = <69>; + ti,davinci-gpio-unbanked = <0>; + power-domains = <&k3_pds 105 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 105 0>; + clock-names = "gpio"; + }; + main_uart0: serial@2800000 { compatible = "ti,j721e-uart", "ti,am654-uart"; reg = <0x00 0x02800000 0x00 0x100>; -- 2.17.1 ^ permalink raw reply related [flat|nested] 10+ messages in thread
* Re: [PATCH v3 1/2] dts: ti: k3-j7200-main: Add support for zeroth instance of GPIO subsystem 2021-01-27 15:08 ` [PATCH v3 1/2] dts: ti: k3-j7200-main: Add support for zeroth instance of GPIO subsystem Aswath Govindraju @ 2021-01-27 15:12 ` Nishanth Menon 2021-01-27 15:26 ` Aswath Govindraju 0 siblings, 1 reply; 10+ messages in thread From: Nishanth Menon @ 2021-01-27 15:12 UTC (permalink / raw) To: Aswath Govindraju Cc: Vignesh Raghavendra, Lokesh Vutla, Kishon Vijay Abraham I, Faiz Abbas, Tero Kristo, Rob Herring, linux-arm-kernel, devicetree, linux-kernel On 20:38-20210127, Aswath Govindraju wrote: > Add support for the zeroth instance of GPIO subsystem in the main domain. > > Signed-off-by: Aswath Govindraju <a-govindraju@ti.com> I really dont want to pick up one patch per node instance. It is hard to scale and just creates a lot of noise. > --- > arch/arm64/boot/dts/ti/k3-j7200-main.dtsi | 17 +++++++++++++++++ > 1 file changed, 17 insertions(+) > > diff --git a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi > index 4cc2e9094d0e..75dffbb26d52 100644 > --- a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi > +++ b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi > @@ -294,6 +294,23 @@ > pinctrl-single,function-mask = <0xffffffff>; > }; > > + main_gpio0: gpio@600000 { > + compatible = "ti,j721e-gpio", "ti,keystone-gpio"; > + reg = <0x0 0x00600000 0x0 0x100>; > + gpio-controller; > + #gpio-cells = <2>; > + interrupt-parent = <&main_gpio_intr>; > + interrupts = <145>, <146>, <147>, <148>, > + <149>; > + interrupt-controller; > + #interrupt-cells = <2>; > + ti,ngpio = <69>; > + ti,davinci-gpio-unbanked = <0>; > + power-domains = <&k3_pds 105 TI_SCI_PD_EXCLUSIVE>; > + clocks = <&k3_clks 105 0>; > + clock-names = "gpio"; > + }; > + > main_uart0: serial@2800000 { > compatible = "ti,j721e-uart", "ti,am654-uart"; > reg = <0x00 0x02800000 0x00 0x100>; > -- > 2.17.1 > -- Regards, Nishanth Menon Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D ^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH v3 1/2] dts: ti: k3-j7200-main: Add support for zeroth instance of GPIO subsystem 2021-01-27 15:12 ` Nishanth Menon @ 2021-01-27 15:26 ` Aswath Govindraju 2021-01-27 15:54 ` Nishanth Menon 0 siblings, 1 reply; 10+ messages in thread From: Aswath Govindraju @ 2021-01-27 15:26 UTC (permalink / raw) To: Nishanth Menon Cc: Vignesh Raghavendra, Lokesh Vutla, Kishon Vijay Abraham I, Faiz Abbas, Tero Kristo, Rob Herring, linux-arm-kernel, devicetree, linux-kernel Hi Nishanth, On 27/01/21 8:42 pm, Nishanth Menon wrote: > On 20:38-20210127, Aswath Govindraju wrote: >> Add support for the zeroth instance of GPIO subsystem in the main domain. >> >> Signed-off-by: Aswath Govindraju <a-govindraju@ti.com> > > > I really dont want to pick up one patch per node instance. It is hard > to scale and just creates a lot of noise. > As the main goal of the patch series was to add support for higher speed modes in MMC, I added only the required ones. If required I will send a follow up patch to add the remaining GPIO nodes. Thanks, Aswath >> --- >> arch/arm64/boot/dts/ti/k3-j7200-main.dtsi | 17 +++++++++++++++++ >> 1 file changed, 17 insertions(+) >> >> diff --git a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi >> index 4cc2e9094d0e..75dffbb26d52 100644 >> --- a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi >> +++ b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi >> @@ -294,6 +294,23 @@ >> pinctrl-single,function-mask = <0xffffffff>; >> }; >> >> + main_gpio0: gpio@600000 { >> + compatible = "ti,j721e-gpio", "ti,keystone-gpio"; >> + reg = <0x0 0x00600000 0x0 0x100>; >> + gpio-controller; >> + #gpio-cells = <2>; >> + interrupt-parent = <&main_gpio_intr>; >> + interrupts = <145>, <146>, <147>, <148>, >> + <149>; >> + interrupt-controller; >> + #interrupt-cells = <2>; >> + ti,ngpio = <69>; >> + ti,davinci-gpio-unbanked = <0>; >> + power-domains = <&k3_pds 105 TI_SCI_PD_EXCLUSIVE>; >> + clocks = <&k3_clks 105 0>; >> + clock-names = "gpio"; >> + }; >> + >> main_uart0: serial@2800000 { >> compatible = "ti,j721e-uart", "ti,am654-uart"; >> reg = <0x00 0x02800000 0x00 0x100>; >> -- >> 2.17.1 >> > ^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH v3 1/2] dts: ti: k3-j7200-main: Add support for zeroth instance of GPIO subsystem 2021-01-27 15:26 ` Aswath Govindraju @ 2021-01-27 15:54 ` Nishanth Menon 2021-01-28 16:21 ` Aswath Govindraju 0 siblings, 1 reply; 10+ messages in thread From: Nishanth Menon @ 2021-01-27 15:54 UTC (permalink / raw) To: Aswath Govindraju Cc: Vignesh Raghavendra, Lokesh Vutla, Kishon Vijay Abraham I, Faiz Abbas, Tero Kristo, Rob Herring, linux-arm-kernel, devicetree, linux-kernel On 20:56-20210127, Aswath Govindraju wrote: > Hi Nishanth, > > On 27/01/21 8:42 pm, Nishanth Menon wrote: > > On 20:38-20210127, Aswath Govindraju wrote: > >> Add support for the zeroth instance of GPIO subsystem in the main domain. > >> > >> Signed-off-by: Aswath Govindraju <a-govindraju@ti.com> > > > > > > I really dont want to pick up one patch per node instance. It is hard > > to scale and just creates a lot of noise. > > > > As the main goal of the patch series was to add support for higher speed > modes in MMC, I added only the required ones. If required I will send a > follow up patch to add the remaining GPIO nodes. I dont plan on picking this patch up in it's current form. please send a patch with all the gpio nodes added in as it makes no sense to split these out. -- Regards, Nishanth Menon Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D ^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH v3 1/2] dts: ti: k3-j7200-main: Add support for zeroth instance of GPIO subsystem 2021-01-27 15:54 ` Nishanth Menon @ 2021-01-28 16:21 ` Aswath Govindraju 0 siblings, 0 replies; 10+ messages in thread From: Aswath Govindraju @ 2021-01-28 16:21 UTC (permalink / raw) To: Nishanth Menon Cc: Vignesh Raghavendra, Lokesh Vutla, Kishon Vijay Abraham I, Faiz Abbas, Tero Kristo, Rob Herring, linux-arm-kernel, devicetree, linux-kernel Hi Nishanth, On 27/01/21 9:24 pm, Nishanth Menon wrote: > On 20:56-20210127, Aswath Govindraju wrote: >> Hi Nishanth, >> >> On 27/01/21 8:42 pm, Nishanth Menon wrote: >>> On 20:38-20210127, Aswath Govindraju wrote: >>>> Add support for the zeroth instance of GPIO subsystem in the main domain. >>>> >>>> Signed-off-by: Aswath Govindraju <a-govindraju@ti.com> >>> >>> >>> I really dont want to pick up one patch per node instance. It is hard >>> to scale and just creates a lot of noise. >>> >> >> As the main goal of the patch series was to add support for higher speed >> modes in MMC, I added only the required ones. If required I will send a >> follow up patch to add the remaining GPIO nodes. > > > I dont plan on picking this patch up in it's current form. please send a > patch with all the gpio nodes added in as it makes no sense to split > these out. > I have sent a respin for this patch series(v4) which adds all the GPIO nodes in the device tree files. Thanks, Aswath ^ permalink raw reply [flat|nested] 10+ messages in thread
* [PATCH v3 2/2] arm64: dts: ti: k3-j7200: Add support for higher speed modes in MMCSD subsystems 2021-01-27 15:08 [PATCH v3 0/2] J7200: Add support for higher speed modes in MMCSD subsystems Aswath Govindraju 2021-01-27 15:08 ` [PATCH v3 1/2] dts: ti: k3-j7200-main: Add support for zeroth instance of GPIO subsystem Aswath Govindraju @ 2021-01-27 15:08 ` Aswath Govindraju 2021-01-27 15:14 ` Nishanth Menon 1 sibling, 1 reply; 10+ messages in thread From: Aswath Govindraju @ 2021-01-27 15:08 UTC (permalink / raw) Cc: Vignesh Raghavendra, Lokesh Vutla, Kishon Vijay Abraham I, Faiz Abbas, Aswath Govindraju, Nishanth Menon, Tero Kristo, Rob Herring, linux-arm-kernel, devicetree, linux-kernel The following speed modes are now supported in J7200 SoC, - HS200 and HS400 modes at 1.8 V card voltage, in MMCSD0 subsystem [1]. - UHS-I speed modes in MMCSD1 subsystem [1]. Add support for UHS-I modes by adding voltage regulator device tree nodes and corresponding pinmux details, to power cycle and voltage switch cards. Also set respective tags in sdhci0 and remove no-1-8-v tag from sdhci1 device tree nodes. [1] - section 12.3.6.1.1 MMCSD Features, in https://www.ti.com/lit/ug/spruiu1a/spruiu1a.pdf Signed-off-by: Aswath Govindraju <a-govindraju@ti.com> --- performance test logs using EXT4 filesystem for eMMC HS400 speed mode, https://pastebin.ubuntu.com/p/KFphDYXj93/ performance test logs using EXT4 filesystem for SD SDR104 speed mode, https://pastebin.ubuntu.com/p/GQKtwGT8Qg/ .../dts/ti/k3-j7200-common-proc-board.dts | 31 +++++++++++++++++++ arch/arm64/boot/dts/ti/k3-j7200-main.dtsi | 3 +- 2 files changed, 33 insertions(+), 1 deletion(-) diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts index 4a7182abccf5..1e1a0022822d 100644 --- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts +++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts @@ -16,6 +16,29 @@ stdout-path = "serial2:115200n8"; bootargs = "console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000"; }; + + vdd_mmc1: fixedregulator-sd { + compatible = "regulator-fixed"; + regulator-name = "vdd_mmc1"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + enable-active-high; + gpios = <&exp2 2 GPIO_ACTIVE_HIGH>; + }; + + vdd_sd_dv: gpio-regulator-vdd-sd-dv { + compatible = "regulator-gpio"; + regulator-name = "vdd_sd_dv"; + pinctrl-names = "default"; + pinctrl-0 = <&vdd_sd_dv_pins_default>; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + gpios = <&main_gpio0 55 GPIO_ACTIVE_HIGH>; + states = <1800000 0x0 + 3300000 0x1>; + }; }; &wkup_pmx0 { @@ -70,6 +93,12 @@ J721E_IOPAD(0x120, PIN_OUTPUT, 0) /* (T4) USB0_DRVVBUS */ >; }; + + vdd_sd_dv_pins_default: vdd_sd_dv_pins_default { + pinctrl-single,pins = < + J721E_IOPAD(0xd0, PIN_INPUT, 7) /* (T5) SPI0_D1.GPIO0_55 */ + >; + }; }; &wkup_uart0 { @@ -190,6 +219,8 @@ /* SD card */ pinctrl-0 = <&main_mmc1_pins_default>; pinctrl-names = "default"; + vmmc-supply = <&vdd_mmc1>; + vqmmc-supply = <&vdd_sd_dv>; ti,driver-strength-ohm = <50>; disable-wp; }; diff --git a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi index 75dffbb26d52..8392d771ef13 100644 --- a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi +++ b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi @@ -534,6 +534,8 @@ ti,trm-icp = <0x8>; bus-width = <8>; mmc-ddr-1_8v; + mmc-hs200-1_8v; + mmc-hs400-1_8v; dma-coherent; }; @@ -551,7 +553,6 @@ ti,otap-del-sel-sdr50 = <0xc>; ti,otap-del-sel-sdr104 = <0x5>; ti,otap-del-sel-ddr50 = <0xc>; - no-1-8-v; dma-coherent; }; -- 2.17.1 ^ permalink raw reply related [flat|nested] 10+ messages in thread
* Re: [PATCH v3 2/2] arm64: dts: ti: k3-j7200: Add support for higher speed modes in MMCSD subsystems 2021-01-27 15:08 ` [PATCH v3 2/2] arm64: dts: ti: k3-j7200: Add support for higher speed modes in MMCSD subsystems Aswath Govindraju @ 2021-01-27 15:14 ` Nishanth Menon 2021-01-27 15:20 ` Aswath Govindraju 0 siblings, 1 reply; 10+ messages in thread From: Nishanth Menon @ 2021-01-27 15:14 UTC (permalink / raw) To: Aswath Govindraju Cc: Vignesh Raghavendra, Lokesh Vutla, Kishon Vijay Abraham I, Faiz Abbas, Tero Kristo, Rob Herring, linux-arm-kernel, devicetree, linux-kernel On 20:38-20210127, Aswath Govindraju wrote: > The following speed modes are now supported in J7200 SoC, > - HS200 and HS400 modes at 1.8 V card voltage, in MMCSD0 subsystem [1]. > - UHS-I speed modes in MMCSD1 subsystem [1]. > > Add support for UHS-I modes by adding voltage regulator device tree nodes > and corresponding pinmux details, to power cycle and voltage switch cards. > Also set respective tags in sdhci0 and remove no-1-8-v tag from sdhci1 > device tree nodes. > > [1] - section 12.3.6.1.1 MMCSD Features, in > https://www.ti.com/lit/ug/spruiu1a/spruiu1a.pdf > > Signed-off-by: Aswath Govindraju <a-govindraju@ti.com> > --- > > performance test logs using EXT4 filesystem for eMMC HS400 speed mode, > https://pastebin.ubuntu.com/p/KFphDYXj93/ > 5.11.0-rc3-next-20210118-00004 : a) could you make sure to post patches when you test with latest next? b) I see 2 patches in this series, but delta seems to be 4 patches, is there a dependency I am not aware of? -- Regards, Nishanth Menon Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D ^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH v3 2/2] arm64: dts: ti: k3-j7200: Add support for higher speed modes in MMCSD subsystems 2021-01-27 15:14 ` Nishanth Menon @ 2021-01-27 15:20 ` Aswath Govindraju 2021-01-27 15:54 ` Nishanth Menon 0 siblings, 1 reply; 10+ messages in thread From: Aswath Govindraju @ 2021-01-27 15:20 UTC (permalink / raw) To: Nishanth Menon Cc: Vignesh Raghavendra, Lokesh Vutla, Kishon Vijay Abraham I, Faiz Abbas, Tero Kristo, Rob Herring, linux-arm-kernel, devicetree, linux-kernel Hi Nishanth, On 27/01/21 8:44 pm, Nishanth Menon wrote: > On 20:38-20210127, Aswath Govindraju wrote: >> The following speed modes are now supported in J7200 SoC, >> - HS200 and HS400 modes at 1.8 V card voltage, in MMCSD0 subsystem [1]. >> - UHS-I speed modes in MMCSD1 subsystem [1]. >> >> Add support for UHS-I modes by adding voltage regulator device tree nodes >> and corresponding pinmux details, to power cycle and voltage switch cards. >> Also set respective tags in sdhci0 and remove no-1-8-v tag from sdhci1 >> device tree nodes. >> >> [1] - section 12.3.6.1.1 MMCSD Features, in >> https://www.ti.com/lit/ug/spruiu1a/spruiu1a.pdf >> >> Signed-off-by: Aswath Govindraju <a-govindraju@ti.com> >> --- >> >> performance test logs using EXT4 filesystem for eMMC HS400 speed mode, >> https://pastebin.ubuntu.com/p/KFphDYXj93/ >> > > 5.11.0-rc3-next-20210118-00004 : > > a) could you make sure to post patches when you test with latest next? > b) I see 2 patches in this series, but delta seems to be 4 patches, is > there a dependency I am not aware of? > There are no dependencies. The other two commits are completely unrelated. From next time I will make sure that I use the latest next and the delta matches. Thanks, Aswath ^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH v3 2/2] arm64: dts: ti: k3-j7200: Add support for higher speed modes in MMCSD subsystems 2021-01-27 15:20 ` Aswath Govindraju @ 2021-01-27 15:54 ` Nishanth Menon 0 siblings, 0 replies; 10+ messages in thread From: Nishanth Menon @ 2021-01-27 15:54 UTC (permalink / raw) To: Aswath Govindraju Cc: Vignesh Raghavendra, Lokesh Vutla, Kishon Vijay Abraham I, Faiz Abbas, Tero Kristo, Rob Herring, linux-arm-kernel, devicetree, linux-kernel On 20:50-20210127, Aswath Govindraju wrote: > Hi Nishanth, > > On 27/01/21 8:44 pm, Nishanth Menon wrote: > > On 20:38-20210127, Aswath Govindraju wrote: > >> The following speed modes are now supported in J7200 SoC, > >> - HS200 and HS400 modes at 1.8 V card voltage, in MMCSD0 subsystem [1]. > >> - UHS-I speed modes in MMCSD1 subsystem [1]. > >> > >> Add support for UHS-I modes by adding voltage regulator device tree nodes > >> and corresponding pinmux details, to power cycle and voltage switch cards. > >> Also set respective tags in sdhci0 and remove no-1-8-v tag from sdhci1 > >> device tree nodes. > >> > >> [1] - section 12.3.6.1.1 MMCSD Features, in > >> https://www.ti.com/lit/ug/spruiu1a/spruiu1a.pdf > >> > >> Signed-off-by: Aswath Govindraju <a-govindraju@ti.com> > >> --- > >> > >> performance test logs using EXT4 filesystem for eMMC HS400 speed mode, > >> https://pastebin.ubuntu.com/p/KFphDYXj93/ > >> > > > > 5.11.0-rc3-next-20210118-00004 : > > > > a) could you make sure to post patches when you test with latest next? > > b) I see 2 patches in this series, but delta seems to be 4 patches, is > > there a dependency I am not aware of? > > > > There are no dependencies. The other two commits are completely > unrelated. From next time I will make sure that I use the latest next > and the delta matches. Thanks. -- Regards, Nishanth Menon Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D ^ permalink raw reply [flat|nested] 10+ messages in thread
end of thread, other threads:[~2021-01-28 16:23 UTC | newest] Thread overview: 10+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2021-01-27 15:08 [PATCH v3 0/2] J7200: Add support for higher speed modes in MMCSD subsystems Aswath Govindraju 2021-01-27 15:08 ` [PATCH v3 1/2] dts: ti: k3-j7200-main: Add support for zeroth instance of GPIO subsystem Aswath Govindraju 2021-01-27 15:12 ` Nishanth Menon 2021-01-27 15:26 ` Aswath Govindraju 2021-01-27 15:54 ` Nishanth Menon 2021-01-28 16:21 ` Aswath Govindraju 2021-01-27 15:08 ` [PATCH v3 2/2] arm64: dts: ti: k3-j7200: Add support for higher speed modes in MMCSD subsystems Aswath Govindraju 2021-01-27 15:14 ` Nishanth Menon 2021-01-27 15:20 ` Aswath Govindraju 2021-01-27 15:54 ` Nishanth Menon
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).