From: <kostap@marvell.com>
To: <linux-kernel@vger.kernel.org>, <devicetree@vger.kernel.org>,
<linux-arm-kernel@lists.infradead.org>
Cc: <vladimir.vid@sartura.hr>, <tmn505@gmail.com>,
<luka.kovacic@sartura.hr>, <sebastian.hesselbarth@gmail.com>,
<gregory.clement@bootlin.com>, <andrew@lunn.ch>,
<robh+dt@kernel.org>, <vkoul@kernel.org>, <kishon@ti.com>,
<miquel.raynal@bootlin.com>, <mw@semihalf.com>,
<jaz@semihalf.com>, <nadavh@marvell.com>, <stefanc@marvell.com>,
<bpeled@marvell.com>,
"Konstantin Porotchkin" <kostap@marvell.com>
Subject: [PATCH v5 0/5] DTS updates for Marvell Armada CN913x platforms
Date: Wed, 10 Feb 2021 15:15:59 +0200 [thread overview]
Message-ID: <20210210131604.28806-1-kostap@marvell.com> (raw)
From: Konstantin Porotchkin <kostap@marvell.com>
This patch series contains the following changes/fixes:
1. Add support for Armada CN913x Development Board topology "B"
2. Add support for Armada CN913x Reference Design boards (CRB)
3. Fixes the CP11X references in PHY binding document
4. Fixes the NAND paritioninig scheme in DTS eliminating gap between
consecutive partitions
All above changes are already intergated into Marvell official SDK sources
v2:
- extract common nodes from DB boards to separate DTSI files
- disable eth2 on CRB boards until the required phy mode support is added
- mention the switch part ID in CRB board description
v3:
- do not rename setup A DTS files for DB variants
- fix a couple of wrong include names
v4:
- Rebase on top of Linus master branch (v5.11-rc7)
- Remove HS400 timing from CRB AP SDHCI (not supported by connected eMMC)
- Add cd-gpio entry to CP0 SDHCI for SD card support
- Add a comment to CN9130-CRB patch about the required defconfig
changes for supporting the onboard i2c expander
- Add Stefan's patch to enable 10G port on CN9130-DB platforms
v5:
- Extend enablement of 10G port to CN9131-DB platform
Grzegorz Jaszczyk (1):
Documentation/bindings: phy: update references to cp11x
Konstantin Porotchkin (3):
arch/arm64/boot/dts/marvell: fix NAND partitioning scheme
arm64: dts: cn913x: add device trees for topology B boards
arm64: dts: add support for Marvell cn9130-crb platform
Stefan Chulski (1):
dts: marvell: Enable 10G interfaces on 9130-DB and 9131-DB boards
.../bindings/phy/phy-mvebu-comphy.txt | 12 +-
arch/arm64/boot/dts/marvell/Makefile | 5 +
arch/arm64/boot/dts/marvell/cn9130-crb-A.dts | 38 ++
arch/arm64/boot/dts/marvell/cn9130-crb-B.dts | 46 ++
arch/arm64/boot/dts/marvell/cn9130-crb.dtsi | 222 ++++++++++
arch/arm64/boot/dts/marvell/cn9130-db-B.dts | 22 +
arch/arm64/boot/dts/marvell/cn9130-db.dts | 393 +----------------
arch/arm64/boot/dts/marvell/cn9130-db.dtsi | 402 ++++++++++++++++++
arch/arm64/boot/dts/marvell/cn9131-db-B.dts | 22 +
arch/arm64/boot/dts/marvell/cn9131-db.dts | 192 +--------
arch/arm64/boot/dts/marvell/cn9131-db.dtsi | 201 +++++++++
arch/arm64/boot/dts/marvell/cn9132-db-B.dts | 22 +
arch/arm64/boot/dts/marvell/cn9132-db.dts | 211 +--------
arch/arm64/boot/dts/marvell/cn9132-db.dtsi | 220 ++++++++++
14 files changed, 1224 insertions(+), 784 deletions(-)
create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb-A.dts
create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb-B.dts
create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb.dtsi
create mode 100644 arch/arm64/boot/dts/marvell/cn9130-db-B.dts
create mode 100644 arch/arm64/boot/dts/marvell/cn9130-db.dtsi
create mode 100644 arch/arm64/boot/dts/marvell/cn9131-db-B.dts
create mode 100644 arch/arm64/boot/dts/marvell/cn9131-db.dtsi
create mode 100644 arch/arm64/boot/dts/marvell/cn9132-db-B.dts
create mode 100644 arch/arm64/boot/dts/marvell/cn9132-db.dtsi
--
2.17.1
next reply other threads:[~2021-02-10 13:17 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-02-10 13:15 kostap [this message]
2021-02-10 13:16 ` [PATCH v5 1/5] Documentation/bindings: phy: update references to cp11x kostap
2021-02-10 19:03 ` Rob Herring
2021-02-10 13:16 ` [PATCH v5 2/5] arch/arm64/boot/dts/marvell: fix NAND partitioning scheme kostap
2021-02-10 13:16 ` [PATCH v5 3/5] arm64: dts: cn913x: add device trees for topology B boards kostap
2021-02-10 13:16 ` [PATCH v5 4/5] dts: marvell: Enable 10G interfaces on 9130-DB and 9131-DB boards kostap
2021-02-10 14:02 ` Marcin Wojtas
2021-02-10 13:16 ` [PATCH v5 5/5] arm64: dts: add support for Marvell cn9130-crb platform kostap
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20210210131604.28806-1-kostap@marvell.com \
--to=kostap@marvell.com \
--cc=andrew@lunn.ch \
--cc=bpeled@marvell.com \
--cc=devicetree@vger.kernel.org \
--cc=gregory.clement@bootlin.com \
--cc=jaz@semihalf.com \
--cc=kishon@ti.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=luka.kovacic@sartura.hr \
--cc=miquel.raynal@bootlin.com \
--cc=mw@semihalf.com \
--cc=nadavh@marvell.com \
--cc=robh+dt@kernel.org \
--cc=sebastian.hesselbarth@gmail.com \
--cc=stefanc@marvell.com \
--cc=tmn505@gmail.com \
--cc=vkoul@kernel.org \
--cc=vladimir.vid@sartura.hr \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).