[PATCH v3 0/9] soundwire: qcom: various improvements

[PATCH v3 0/9] soundwire: qcom: various improvements

[Srinivas Kandagatla]

Thanks for reviewing v2 of this patchset!

During testing SoundWire controller on SM8250 MTP, we found
few issues like all the interrupts are not handled,
all transport parameters are not read from device tree.
Patch to add Auto Enumeration supported by the controller
is also part of this series.

Other major issue was register read/writes which was interrupt based
was an overhead and puts lot of limitation on context it can be used from.

With previous approach number of interrupts generated
after enumeration are around 130:
$ cat /proc/interrupts  | grep soundwire
21: 130 0 0 0 0 0 0 0 GICv3 234 Edge      soundwire
    
after this patch they are just 3 interrupts
$ cat /proc/interrupts  | grep soundwire
21: 3 0 0 0 0 0 0 0 GICv3 234 Edge      soundwire

So this patchset add various improvements to the existing driver
to address above issues.

Tested it on SM8250 MTP with 2x WSA881x speakers, HeadPhones on
WCD938x via lpass-rx-macro and Analog MICs via lpass-tx-macro.
Also tested on DragonBoard DB845c with 2xWSA881x speakers.

Changes since v1:
	- added auto enumeration patches to this patchset
	- added comments to qcom bindings to clarify invalid values
	- cleanup trasport parameters to use internal port config

Srinivas Kandagatla (9):
  dt-bindings: soundwire: qcom: clarify data port bus parameters
  soundwire: qcom: add support to missing transport params
  soundwire: qcom: set continue execution flag for ignored commands
  soundwire: qcom: start the clock during initialization
  soundwire: qcom: update register read/write routine
  soundwire: qcom: add support to new interrupts
  soundwire: export sdw_compare_devid() and sdw_extract_slave_id()
  soundwire: qcom: add auto enumeration support
  soundwire: qcom: wait for enumeration to be complete in probe

 .../bindings/soundwire/qcom,sdw.txt           |  20 +
 drivers/soundwire/bus.c                       |   4 +-
 drivers/soundwire/qcom.c                      | 529 ++++++++++++++----
 include/linux/soundwire/sdw.h                 |   2 +
 4 files changed, 441 insertions(+), 114 deletions(-)

-- 
2.21.0

[PATCH v3 1/9] dt-bindings: soundwire: qcom: clarify data port bus parameters

[Srinivas Kandagatla]

Some of the parameters for data ports are not applicable or not implemented
in IP. So mark them as invalid/not applicable in DT so that controller is
aware of this.

Add comment to these bindings to provide more clarity on the values!

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
---
 .../bindings/soundwire/qcom,sdw.txt           | 20 +++++++++++++++++++
 1 file changed, 20 insertions(+)

diff --git a/Documentation/devicetree/bindings/soundwire/qcom,sdw.txt b/Documentation/devicetree/bindings/soundwire/qcom,sdw.txt
index b104be131235..b93a2b3e029d 100644
--- a/Documentation/devicetree/bindings/soundwire/qcom,sdw.txt
+++ b/Documentation/devicetree/bindings/soundwire/qcom,sdw.txt
@@ -54,6 +54,8 @@ board specific bus parameters.
 	Value type: <prop-encoded-array>
 	Definition: should specify payload transport window offset1 of each
 		    data port. Out ports followed by In ports.
+		    Value of 0xFF indicates that this option is not implemented
+		    or applicable for the respective data port.
 		    More info in MIPI Alliance SoundWire 1.0 Specifications.
 
 - qcom,ports-offset2:
@@ -61,6 +63,8 @@ board specific bus parameters.
 	Value type: <prop-encoded-array>
 	Definition: should specify payload transport window offset2 of each
 		    data port. Out ports followed by In ports.
+		    Value of 0xFF indicates that this option is not implemented
+		    or applicable for the respective data port.
 		    More info in MIPI Alliance SoundWire 1.0 Specifications.
 
 - qcom,ports-sinterval-low:
@@ -69,12 +73,16 @@ board specific bus parameters.
 	Definition: should be sample interval low of each data port.
 		    Out ports followed by In ports. Used for Sample Interval
 		    calculation.
+		    Value of 0xFF indicates that this option is not implemented
+		    or applicable for the respective data port.
 		    More info in MIPI Alliance SoundWire 1.0 Specifications.
 
 - qcom,ports-word-length:
 	Usage: optional
 	Value type: <prop-encoded-array>
 	Definition: should be size of payload channel sample.
+		    Value of 0xFF indicates that this option is not implemented
+		    or applicable for the respective data port.
 		    More info in MIPI Alliance SoundWire 1.0 Specifications.
 
 - qcom,ports-block-pack-mode:
@@ -84,6 +92,8 @@ board specific bus parameters.
 		    0 to indicate Blocks are per Channel
 		    1 to indicate Blocks are per Port.
 		    Out ports followed by In ports.
+		    Value of 0xFF indicates that this option is not implemented
+		    or applicable for the respective data port.
 		    More info in MIPI Alliance SoundWire 1.0 Specifications.
 
 - qcom,ports-block-group-count:
@@ -92,6 +102,8 @@ board specific bus parameters.
 	Definition: should be in range 1 to 4 to indicate how many sample
 		    intervals are combined into a payload.
 		    Out ports followed by In ports.
+		    Value of 0xFF indicates that this option is not implemented
+		    or applicable for the respective data port.
 		    More info in MIPI Alliance SoundWire 1.0 Specifications.
 
 - qcom,ports-lane-control:
@@ -100,6 +112,8 @@ board specific bus parameters.
 	Definition: should be in range 0 to 7 to identify which	data lane
 		    the data port uses.
 		    Out ports followed by In ports.
+		    Value of 0xFF indicates that this option is not implemented
+		    or applicable for the respective data port.
 		    More info in MIPI Alliance SoundWire 1.0 Specifications.
 
 - qcom,ports-hstart:
@@ -109,6 +123,8 @@ board specific bus parameters.
 		    SoundWire Frame, i.e. left edge of the Transport sub-frame
 		    for each port. Values between 0 and 15 are valid.
 		    Out ports followed by In ports.
+		    Value of 0xFF indicates that this option is not implemented
+		    or applicable for the respective data port.
 		    More info in MIPI Alliance SoundWire 1.0 Specifications.
 
 - qcom,ports-hstop:
@@ -118,6 +134,8 @@ board specific bus parameters.
 		    SoundWire Frame, i.e. the right edge of the Transport
 		    sub-frame for each port. Values between 0 and 15 are valid.
 		    Out ports followed by In ports.
+		    Value of 0xFF indicates that this option is not implemented
+		    or applicable for the respective data port.
 		    More info in MIPI Alliance SoundWire 1.0 Specifications.
 
 - qcom,dports-type:
@@ -128,6 +146,8 @@ board specific bus parameters.
 		    1 for simple ports
 		    2 for full port
 		    Out ports followed by In ports.
+		    Value of 0xFF indicates that this option is not implemented
+		    or applicable for the respective data port.
 		    More info in MIPI Alliance SoundWire 1.0 Specifications.
 
 Note:
-- 
2.21.0

[PATCH v3 2/9] soundwire: qcom: add support to missing transport params

[Srinivas Kandagatla]

Some of the transport parameters derived from device tree
are not fully parsed by the driver.

This patch adds support to parse those missing parameters.

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
---
 drivers/soundwire/qcom.c | 107 ++++++++++++++++++++++++++++++++++-----
 1 file changed, 95 insertions(+), 12 deletions(-)

diff --git a/drivers/soundwire/qcom.c b/drivers/soundwire/qcom.c
index 6d22df01f354..6c7b811eea94 100644
--- a/drivers/soundwire/qcom.c
+++ b/drivers/soundwire/qcom.c
@@ -54,7 +54,13 @@
 #define SWRM_MCP_SLV_STATUS					0x1090
 #define SWRM_MCP_SLV_STATUS_MASK				GENMASK(1, 0)
 #define SWRM_DP_PORT_CTRL_BANK(n, m)	(0x1124 + 0x100 * (n - 1) + 0x40 * m)
+#define SWRM_DP_PORT_CTRL_2_BANK(n, m)	(0x1128 + 0x100 * (n - 1) + 0x40 * m)
+#define SWRM_DP_BLOCK_CTRL_1(n)		(0x112C + 0x100 * (n - 1))
+#define SWRM_DP_BLOCK_CTRL2_BANK(n, m)	(0x1130 + 0x100 * (n - 1) + 0x40 * m)
+#define SWRM_DP_PORT_HCTRL_BANK(n, m)	(0x1134 + 0x100 * (n - 1) + 0x40 * m)
 #define SWRM_DP_BLOCK_CTRL3_BANK(n, m)	(0x1138 + 0x100 * (n - 1) + 0x40 * m)
+#define SWRM_DIN_DPn_PCM_PORT_CTRL(n)	(0x1054 + 0x100 * (n - 1))
+
 #define SWRM_DP_PORT_CTRL_EN_CHAN_SHFT				0x18
 #define SWRM_DP_PORT_CTRL_OFFSET2_SHFT				0x10
 #define SWRM_DP_PORT_CTRL_OFFSET1_SHFT				0x08
@@ -73,12 +79,20 @@
 #define QCOM_SDW_MAX_PORTS	14
 #define DEFAULT_CLK_FREQ	9600000
 #define SWRM_MAX_DAIS		0xF
+#define SWR_INVALID_PARAM 0xFF
+#define SWR_HSTOP_MAX_VAL 0xF
+#define SWR_HSTART_MIN_VAL 0x0
 
 struct qcom_swrm_port_config {
 	u8 si;
 	u8 off1;
 	u8 off2;
 	u8 bp_mode;
+	u8 hstart;
+	u8 hstop;
+	u8 word_length;
+	u8 blk_group_count;
+	u8 lane_control;
 };
 
 struct qcom_swrm_ctrl {
@@ -396,8 +410,11 @@ static int qcom_swrm_port_params(struct sdw_bus *bus,
 				 struct sdw_port_params *p_params,
 				 unsigned int bank)
 {
-	/* TBD */
-	return 0;
+	struct qcom_swrm_ctrl *ctrl = to_qcom_sdw(bus);
+
+	return ctrl->reg_write(ctrl, SWRM_DP_BLOCK_CTRL_1(p_params->num),
+			       p_params->bps - 1);
+
 }
 
 static int qcom_swrm_transport_params(struct sdw_bus *bus,
@@ -405,20 +422,45 @@ static int qcom_swrm_transport_params(struct sdw_bus *bus,
 				      enum sdw_reg_bank bank)
 {
 	struct qcom_swrm_ctrl *ctrl = to_qcom_sdw(bus);
+	struct qcom_swrm_port_config *pcfg;
 	u32 value;
 	int reg = SWRM_DP_PORT_CTRL_BANK((params->port_num), bank);
 	int ret;
 
-	value = params->offset1 << SWRM_DP_PORT_CTRL_OFFSET1_SHFT;
-	value |= params->offset2 << SWRM_DP_PORT_CTRL_OFFSET2_SHFT;
-	value |= params->sample_interval - 1;
+	pcfg = &ctrl->pconfig[params->port_num - 1];
+
+	value = pcfg->off1 << SWRM_DP_PORT_CTRL_OFFSET1_SHFT;
+	value |= pcfg->off2 << SWRM_DP_PORT_CTRL_OFFSET2_SHFT;
+	value |= pcfg->si;
 
 	ret = ctrl->reg_write(ctrl, reg, value);
 
-	if (!ret && params->blk_pkg_mode) {
-		reg = SWRM_DP_BLOCK_CTRL3_BANK(params->port_num, bank);
+	if (pcfg->lane_control != SWR_INVALID_PARAM) {
+		reg = SWRM_DP_PORT_CTRL_2_BANK(params->port_num, bank);
+		value = pcfg->lane_control;
+		ret = ctrl->reg_write(ctrl, reg, value);
+	}
+
+	if (pcfg->blk_group_count != SWR_INVALID_PARAM) {
+		reg = SWRM_DP_BLOCK_CTRL2_BANK(params->port_num, bank);
+		value = pcfg->blk_group_count;
+		ret = ctrl->reg_write(ctrl, reg, value);
+	}
+
+	if (pcfg->hstart != SWR_INVALID_PARAM
+			&& pcfg->hstop != SWR_INVALID_PARAM) {
+		reg = SWRM_DP_PORT_HCTRL_BANK(params->port_num, bank);
+		value = (pcfg->hstop << 4) | pcfg->hstart;
+		ret = ctrl->reg_write(ctrl, reg, value);
+	} else {
+		reg = SWRM_DP_PORT_HCTRL_BANK(params->port_num, bank);
+		value = (SWR_HSTOP_MAX_VAL << 4) | SWR_HSTART_MIN_VAL;
+		ret = ctrl->reg_write(ctrl, reg, value);
+	}
 
-		ret = ctrl->reg_write(ctrl, reg, 1);
+	if (pcfg->bp_mode != SWR_INVALID_PARAM) {
+		reg = SWRM_DP_BLOCK_CTRL3_BANK(params->port_num, bank);
+		ret = ctrl->reg_write(ctrl, reg, pcfg->bp_mode);
 	}
 
 	return ret;
@@ -466,10 +508,13 @@ static int qcom_swrm_compute_params(struct sdw_bus *bus)
 		list_for_each_entry(p_rt, &m_rt->port_list, port_node) {
 			pcfg = &ctrl->pconfig[p_rt->num - 1];
 			p_rt->transport_params.port_num = p_rt->num;
-			p_rt->transport_params.sample_interval = pcfg->si + 1;
-			p_rt->transport_params.offset1 = pcfg->off1;
-			p_rt->transport_params.offset2 = pcfg->off2;
-			p_rt->transport_params.blk_pkg_mode = pcfg->bp_mode;
+			if (pcfg->word_length != SWR_INVALID_PARAM) {
+				sdw_fill_port_params(&p_rt->port_params,
+					     p_rt->num,  pcfg->word_length + 1,
+					     SDW_PORT_FLOW_MODE_ISOCH,
+					     SDW_PORT_DATA_MODE_NORMAL);
+			}
+
 		}
 
 		list_for_each_entry(s_rt, &m_rt->slave_rt_list, m_rt_node) {
@@ -481,6 +526,18 @@ static int qcom_swrm_compute_params(struct sdw_bus *bus)
 				p_rt->transport_params.offset1 = pcfg->off1;
 				p_rt->transport_params.offset2 = pcfg->off2;
 				p_rt->transport_params.blk_pkg_mode = pcfg->bp_mode;
+				p_rt->transport_params.blk_grp_ctrl = pcfg->blk_group_count;
+
+				p_rt->transport_params.hstart = pcfg->hstart;
+				p_rt->transport_params.hstop = pcfg->hstop;
+				p_rt->transport_params.lane_ctrl = pcfg->lane_control;
+				if (pcfg->word_length != SWR_INVALID_PARAM) {
+					sdw_fill_port_params(&p_rt->port_params,
+						     p_rt->num,
+						     pcfg->word_length + 1,
+						     SDW_PORT_FLOW_MODE_ISOCH,
+						     SDW_PORT_DATA_MODE_NORMAL);
+				}
 				i++;
 			}
 		}
@@ -728,6 +785,11 @@ static int qcom_swrm_get_port_config(struct qcom_swrm_ctrl *ctrl)
 	u8 off2[QCOM_SDW_MAX_PORTS];
 	u8 si[QCOM_SDW_MAX_PORTS];
 	u8 bp_mode[QCOM_SDW_MAX_PORTS] = { 0, };
+	u8 hstart[QCOM_SDW_MAX_PORTS];
+	u8 hstop[QCOM_SDW_MAX_PORTS];
+	u8 word_length[QCOM_SDW_MAX_PORTS];
+	u8 blk_group_count[QCOM_SDW_MAX_PORTS];
+	u8 lane_control[QCOM_SDW_MAX_PORTS];
 	int i, ret, nports, val;
 
 	ctrl->reg_read(ctrl, SWRM_COMP_PARAMS, &val);
@@ -772,11 +834,32 @@ static int qcom_swrm_get_port_config(struct qcom_swrm_ctrl *ctrl)
 
 	ret = of_property_read_u8_array(np, "qcom,ports-block-pack-mode",
 					bp_mode, nports);
+
+	memset(hstart, SWR_INVALID_PARAM, QCOM_SDW_MAX_PORTS);
+	of_property_read_u8_array(np, "qcom,ports-hstart", hstart, nports);
+
+	memset(hstop, SWR_INVALID_PARAM, QCOM_SDW_MAX_PORTS);
+	of_property_read_u8_array(np, "qcom,ports-hstop", hstop, nports);
+
+	memset(word_length, SWR_INVALID_PARAM, QCOM_SDW_MAX_PORTS);
+	of_property_read_u8_array(np, "qcom,ports-word-length", word_length, nports);
+
+	memset(blk_group_count, SWR_INVALID_PARAM, QCOM_SDW_MAX_PORTS);
+	of_property_read_u8_array(np, "qcom,ports-block-group-count", blk_group_count, nports);
+
+	memset(lane_control, SWR_INVALID_PARAM, QCOM_SDW_MAX_PORTS);
+	of_property_read_u8_array(np, "qcom,ports-lane-control", lane_control, nports);
+
 	for (i = 0; i < nports; i++) {
 		ctrl->pconfig[i].si = si[i];
 		ctrl->pconfig[i].off1 = off1[i];
 		ctrl->pconfig[i].off2 = off2[i];
 		ctrl->pconfig[i].bp_mode = bp_mode[i];
+		ctrl->pconfig[i].hstart = hstart[i];
+		ctrl->pconfig[i].hstop = hstop[i];
+		ctrl->pconfig[i].word_length = word_length[i];
+		ctrl->pconfig[i].blk_group_count = blk_group_count[i];
+		ctrl->pconfig[i].lane_control = lane_control[i];
 	}
 
 	return 0;
-- 
2.21.0

[PATCH v3 3/9] soundwire: qcom: set continue execution flag for ignored commands

[Srinivas Kandagatla]

version 1.5.1 and higher IPs of this controller required to set
continue execution on ignored command flag. This patch sets this flag.

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
---
 drivers/soundwire/qcom.c | 11 ++++++++++-
 1 file changed, 10 insertions(+), 1 deletion(-)

diff --git a/drivers/soundwire/qcom.c b/drivers/soundwire/qcom.c
index 6c7b811eea94..076a2b1b6d6d 100644
--- a/drivers/soundwire/qcom.c
+++ b/drivers/soundwire/qcom.c
@@ -40,6 +40,7 @@
 #define SWRM_CMD_FIFO_CMD					0x308
 #define SWRM_CMD_FIFO_STATUS					0x30C
 #define SWRM_CMD_FIFO_CFG_ADDR					0x314
+#define SWRM_CONTINUE_EXEC_ON_CMD_IGNORE			BIT(31)
 #define SWRM_RD_WR_CMD_RETRIES					0x7
 #define SWRM_CMD_FIFO_RD_FIFO_ADDR				0x318
 #define SWRM_ENUMERATOR_CFG_ADDR				0x500
@@ -343,7 +344,15 @@ static int qcom_swrm_init(struct qcom_swrm_ctrl *ctrl)
 	ctrl->reg_write(ctrl, SWRM_MCP_CFG_ADDR, val);
 
 	/* Configure number of retries of a read/write cmd */
-	ctrl->reg_write(ctrl, SWRM_CMD_FIFO_CFG_ADDR, SWRM_RD_WR_CMD_RETRIES);
+	if (ctrl->version > 0x01050001) {
+		/* Only for versions >= 1.5.1 */
+		ctrl->reg_write(ctrl, SWRM_CMD_FIFO_CFG_ADDR,
+				SWRM_RD_WR_CMD_RETRIES |
+				SWRM_CONTINUE_EXEC_ON_CMD_IGNORE);
+	} else {
+		ctrl->reg_write(ctrl, SWRM_CMD_FIFO_CFG_ADDR,
+				SWRM_RD_WR_CMD_RETRIES);
+	}
 
 	/* Set IRQ to PULSE */
 	ctrl->reg_write(ctrl, SWRM_COMP_CFG_ADDR,
-- 
2.21.0

[PATCH v3 4/9] soundwire: qcom: start the clock during initialization

[Srinivas Kandagatla]

Start the clock during initialization, doing this explicitly
will add more clarity when we are adding clock stop feature.

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
---
 drivers/soundwire/qcom.c | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/drivers/soundwire/qcom.c b/drivers/soundwire/qcom.c
index 076a2b1b6d6d..071d05d3a971 100644
--- a/drivers/soundwire/qcom.c
+++ b/drivers/soundwire/qcom.c
@@ -47,6 +47,8 @@
 #define SWRM_MCP_FRAME_CTRL_BANK_ADDR(m)		(0x101C + 0x40 * (m))
 #define SWRM_MCP_FRAME_CTRL_BANK_COL_CTRL_BMSK			GENMASK(2, 0)
 #define SWRM_MCP_FRAME_CTRL_BANK_ROW_CTRL_BMSK			GENMASK(7, 3)
+#define SWRM_MCP_BUS_CTRL					0x1044
+#define SWRM_MCP_BUS_CLK_START					BIT(1)
 #define SWRM_MCP_CFG_ADDR					0x1048
 #define SWRM_MCP_CFG_MAX_NUM_OF_CMD_NO_PINGS_BMSK		GENMASK(21, 17)
 #define SWRM_DEF_CMD_NO_PINGS					0x1f
@@ -343,6 +345,7 @@ static int qcom_swrm_init(struct qcom_swrm_ctrl *ctrl)
 	u32p_replace_bits(&val, SWRM_DEF_CMD_NO_PINGS, SWRM_MCP_CFG_MAX_NUM_OF_CMD_NO_PINGS_BMSK);
 	ctrl->reg_write(ctrl, SWRM_MCP_CFG_ADDR, val);
 
+	ctrl->reg_write(ctrl, SWRM_MCP_BUS_CTRL, SWRM_MCP_BUS_CLK_START);
 	/* Configure number of retries of a read/write cmd */
 	if (ctrl->version > 0x01050001) {
 		/* Only for versions >= 1.5.1 */
-- 
2.21.0

[PATCH v3 5/9] soundwire: qcom: update register read/write routine

[Srinivas Kandagatla]

In the existing code every soundwire register read and register write
are kinda blocked. Each of these are using a special command id that
generates interrupt after it successfully finishes. This is really
overhead, limiting and not really necessary unless we are doing
something special.

We can simply read/write the fifo that should also give exactly
what we need! This will also allow to read/write registers in
interrupt context, which was not possible with the special
command approach.

With previous approach number of interrupts generated
after enumeration are around 130:
$ cat /proc/interrupts  | grep soundwire
 21: 130 0 0 0 0 0 0 0 GICv3 234 Edge      soundwire

after this patch they are just 3 interrupts
$ cat /proc/interrupts  | grep soundwire
 21: 3 0 0 0 0 0 0 0 GICv3 234 Edge      soundwire

This has significantly not only reduced interrupting CPU during enumeration
but also during streaming!

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
---
 drivers/soundwire/qcom.c | 178 ++++++++++++++++++++++-----------------
 1 file changed, 99 insertions(+), 79 deletions(-)

diff --git a/drivers/soundwire/qcom.c b/drivers/soundwire/qcom.c
index 071d05d3a971..7762ff237636 100644
--- a/drivers/soundwire/qcom.c
+++ b/drivers/soundwire/qcom.c
@@ -38,11 +38,13 @@
 #define SWRM_CMD_FIFO_WR_CMD					0x300
 #define SWRM_CMD_FIFO_RD_CMD					0x304
 #define SWRM_CMD_FIFO_CMD					0x308
+#define SWRM_CMD_FIFO_FLUSH					0x1
 #define SWRM_CMD_FIFO_STATUS					0x30C
 #define SWRM_CMD_FIFO_CFG_ADDR					0x314
 #define SWRM_CONTINUE_EXEC_ON_CMD_IGNORE			BIT(31)
 #define SWRM_RD_WR_CMD_RETRIES					0x7
 #define SWRM_CMD_FIFO_RD_FIFO_ADDR				0x318
+#define SWRM_RD_FIFO_CMD_ID_MASK				GENMASK(11, 8)
 #define SWRM_ENUMERATOR_CFG_ADDR				0x500
 #define SWRM_MCP_FRAME_CTRL_BANK_ADDR(m)		(0x101C + 0x40 * (m))
 #define SWRM_MCP_FRAME_CTRL_BANK_COL_CTRL_BMSK			GENMASK(2, 0)
@@ -78,13 +80,16 @@
 #define SWRM_SPECIAL_CMD_ID	0xF
 #define MAX_FREQ_NUM		1
 #define TIMEOUT_MS		(2 * HZ)
-#define QCOM_SWRM_MAX_RD_LEN	0xf
+#define QCOM_SWRM_MAX_RD_LEN	0x1
 #define QCOM_SDW_MAX_PORTS	14
 #define DEFAULT_CLK_FREQ	9600000
 #define SWRM_MAX_DAIS		0xF
 #define SWR_INVALID_PARAM 0xFF
 #define SWR_HSTOP_MAX_VAL 0xF
 #define SWR_HSTART_MIN_VAL 0x0
+#define SWR_BROADCAST_CMD_ID    0x0F
+#define SWR_MAX_CMD_ID	14
+#define MAX_FIFO_RD_RETRY 3
 
 struct qcom_swrm_port_config {
 	u8 si;
@@ -103,10 +108,8 @@ struct qcom_swrm_ctrl {
 	struct device *dev;
 	struct regmap *regmap;
 	void __iomem *mmio;
-	struct completion *comp;
+	struct completion broadcast;
 	struct work_struct slave_work;
-	/* read/write lock */
-	spinlock_t comp_lock;
 	/* Port alloc/free lock */
 	struct mutex port_lock;
 	struct clk *hclk;
@@ -120,6 +123,8 @@ struct qcom_swrm_ctrl {
 	int rows_index;
 	unsigned long dout_port_mask;
 	unsigned long din_port_mask;
+	u8 rcmd_id;
+	u8 wcmd_id;
 	struct qcom_swrm_port_config pconfig[QCOM_SDW_MAX_PORTS];
 	struct sdw_stream_runtime *sruntime[SWRM_MAX_DAIS];
 	enum sdw_slave_status status[SDW_MAX_DEVICES];
@@ -198,77 +203,105 @@ static int qcom_swrm_cpu_reg_write(struct qcom_swrm_ctrl *ctrl, int reg,
 	return SDW_CMD_OK;
 }
 
-static int qcom_swrm_cmd_fifo_wr_cmd(struct qcom_swrm_ctrl *ctrl, u8 cmd_data,
-				     u8 dev_addr, u16 reg_addr)
+static u32 swrm_get_packed_reg_val(u8 *cmd_id, u8 cmd_data,
+				   u8 dev_addr, u16 reg_addr)
 {
-	DECLARE_COMPLETION_ONSTACK(comp);
-	unsigned long flags;
 	u32 val;
-	int ret;
-
-	spin_lock_irqsave(&ctrl->comp_lock, flags);
-	ctrl->comp = &comp;
-	spin_unlock_irqrestore(&ctrl->comp_lock, flags);
-	val = SWRM_REG_VAL_PACK(cmd_data, dev_addr,
-				SWRM_SPECIAL_CMD_ID, reg_addr);
-	ret = ctrl->reg_write(ctrl, SWRM_CMD_FIFO_WR_CMD, val);
-	if (ret)
-		goto err;
-
-	ret = wait_for_completion_timeout(ctrl->comp,
-					  msecs_to_jiffies(TIMEOUT_MS));
+	u8 id = *cmd_id;
 
-	if (!ret)
-		ret = SDW_CMD_IGNORED;
-	else
-		ret = SDW_CMD_OK;
-err:
-	spin_lock_irqsave(&ctrl->comp_lock, flags);
-	ctrl->comp = NULL;
-	spin_unlock_irqrestore(&ctrl->comp_lock, flags);
+	if (id != SWR_BROADCAST_CMD_ID) {
+		if (id < SWR_MAX_CMD_ID)
+			id += 1;
+		else
+			id = 0;
+		*cmd_id = id;
+	}
+	val = SWRM_REG_VAL_PACK(cmd_data, dev_addr, id, reg_addr);
 
-	return ret;
+	return val;
 }
 
-static int qcom_swrm_cmd_fifo_rd_cmd(struct qcom_swrm_ctrl *ctrl,
-				     u8 dev_addr, u16 reg_addr,
-				     u32 len, u8 *rval)
+
+static int qcom_swrm_cmd_fifo_wr_cmd(struct qcom_swrm_ctrl *swrm, u8 cmd_data,
+				     u8 dev_addr, u16 reg_addr)
 {
-	int i, ret;
-	u32 val;
-	DECLARE_COMPLETION_ONSTACK(comp);
-	unsigned long flags;
 
-	spin_lock_irqsave(&ctrl->comp_lock, flags);
-	ctrl->comp = &comp;
-	spin_unlock_irqrestore(&ctrl->comp_lock, flags);
+	u32 val;
+	int ret = 0;
+	u8 cmd_id = 0x0;
 
-	val = SWRM_REG_VAL_PACK(len, dev_addr, SWRM_SPECIAL_CMD_ID, reg_addr);
-	ret = ctrl->reg_write(ctrl, SWRM_CMD_FIFO_RD_CMD, val);
-	if (ret)
-		goto err;
+	if (dev_addr == SDW_BROADCAST_DEV_NUM) {
+		cmd_id = SWR_BROADCAST_CMD_ID;
+		val = swrm_get_packed_reg_val(&cmd_id, cmd_data,
+					      dev_addr, reg_addr);
+	} else {
+		val = swrm_get_packed_reg_val(&swrm->wcmd_id, cmd_data,
+					      dev_addr, reg_addr);
+	}
 
-	ret = wait_for_completion_timeout(ctrl->comp,
-					  msecs_to_jiffies(TIMEOUT_MS));
+	swrm->reg_write(swrm, SWRM_CMD_FIFO_WR_CMD, val);
+
+	/* version 1.3 or less */
+	if (swrm->version <= 0x01030000)
+		usleep_range(150, 155);
+
+	if (cmd_id == SWR_BROADCAST_CMD_ID) {
+		/*
+		 * sleep for 10ms for MSM soundwire variant to allow broadcast
+		 * command to complete.
+		 */
+		ret = wait_for_completion_timeout(&swrm->broadcast,
+						  msecs_to_jiffies(TIMEOUT_MS));
+		if (!ret)
+			ret = SDW_CMD_IGNORED;
+		else
+			ret = SDW_CMD_OK;
 
-	if (!ret) {
-		ret = SDW_CMD_IGNORED;
-		goto err;
 	} else {
 		ret = SDW_CMD_OK;
 	}
+	return ret;
+}
 
-	for (i = 0; i < len; i++) {
-		ctrl->reg_read(ctrl, SWRM_CMD_FIFO_RD_FIFO_ADDR, &val);
-		rval[i] = val & 0xFF;
-	}
+static int qcom_swrm_cmd_fifo_rd_cmd(struct qcom_swrm_ctrl *swrm,
+				     u8 dev_addr, u16 reg_addr,
+				     u32 len, u8 *rval)
+{
+	u32 cmd_data, cmd_id, val, retry_attempt = 0;
+
+	val = swrm_get_packed_reg_val(&swrm->rcmd_id, len, dev_addr, reg_addr);
+
+	/* wait for FIFO RD to complete to avoid overflow */
+	usleep_range(100, 105);
+	swrm->reg_write(swrm, SWRM_CMD_FIFO_RD_CMD, val);
+	/* wait for FIFO RD CMD complete to avoid overflow */
+	usleep_range(250, 255);
+
+	do {
+		swrm->reg_read(swrm, SWRM_CMD_FIFO_RD_FIFO_ADDR, &cmd_data);
+		rval[0] = cmd_data & 0xFF;
+		cmd_id = FIELD_GET(SWRM_RD_FIFO_CMD_ID_MASK, cmd_data);
+
+		if (cmd_id != swrm->rcmd_id) {
+			if (retry_attempt < (MAX_FIFO_RD_RETRY - 1)) {
+				/* wait 500 us before retry on fifo read failure */
+				usleep_range(500, 505);
+				swrm->reg_write(swrm, SWRM_CMD_FIFO_CMD,
+						SWRM_CMD_FIFO_FLUSH);
+				swrm->reg_write(swrm, SWRM_CMD_FIFO_RD_CMD, val);
+			}
+			retry_attempt++;
+		} else {
+			return SDW_CMD_OK;
+		}
 
-err:
-	spin_lock_irqsave(&ctrl->comp_lock, flags);
-	ctrl->comp = NULL;
-	spin_unlock_irqrestore(&ctrl->comp_lock, flags);
+	} while (retry_attempt < MAX_FIFO_RD_RETRY);
 
-	return ret;
+	dev_err(swrm->dev, "failed to read fifo: reg: 0x%x, rcmd_id: 0x%x,\
+		dev_num: 0x%x, cmd_data: 0x%x\n",
+		reg_addr, swrm->rcmd_id, dev_addr, cmd_data);
+
+	return SDW_CMD_IGNORED;
 }
 
 static void qcom_swrm_get_device_status(struct qcom_swrm_ctrl *ctrl)
@@ -291,7 +324,6 @@ static irqreturn_t qcom_swrm_irq_handler(int irq, void *dev_id)
 {
 	struct qcom_swrm_ctrl *ctrl = dev_id;
 	u32 sts, value;
-	unsigned long flags;
 
 	ctrl->reg_read(ctrl, SWRM_INTERRUPT_STATUS, &sts);
 
@@ -304,8 +336,10 @@ static irqreturn_t qcom_swrm_irq_handler(int irq, void *dev_id)
 	}
 
 	if ((sts & SWRM_INTERRUPT_STATUS_NEW_SLAVE_ATTACHED) ||
-	    sts & SWRM_INTERRUPT_STATUS_CHANGE_ENUM_SLAVE_STATUS)
-		schedule_work(&ctrl->slave_work);
+	    sts & SWRM_INTERRUPT_STATUS_CHANGE_ENUM_SLAVE_STATUS) {
+		qcom_swrm_get_device_status(ctrl);
+		sdw_handle_slave_status(&ctrl->bus, ctrl->status);
+	}
 
 	/**
 	 * clear the interrupt before complete() is called, as complete can
@@ -314,15 +348,12 @@ static irqreturn_t qcom_swrm_irq_handler(int irq, void *dev_id)
 	 */
 	ctrl->reg_write(ctrl, SWRM_INTERRUPT_CLEAR, sts);
 
-	if (sts & SWRM_INTERRUPT_STATUS_SPECIAL_CMD_ID_FINISHED) {
-		spin_lock_irqsave(&ctrl->comp_lock, flags);
-		if (ctrl->comp)
-			complete(ctrl->comp);
-		spin_unlock_irqrestore(&ctrl->comp_lock, flags);
-	}
+	if (sts & SWRM_INTERRUPT_STATUS_SPECIAL_CMD_ID_FINISHED)
+		complete(&ctrl->broadcast);
 
 	return IRQ_HANDLED;
 }
+
 static int qcom_swrm_init(struct qcom_swrm_ctrl *ctrl)
 {
 	u32 val;
@@ -562,16 +593,6 @@ static u32 qcom_swrm_freq_tbl[MAX_FREQ_NUM] = {
 	DEFAULT_CLK_FREQ,
 };
 
-static void qcom_swrm_slave_wq(struct work_struct *work)
-{
-	struct qcom_swrm_ctrl *ctrl =
-			container_of(work, struct qcom_swrm_ctrl, slave_work);
-
-	qcom_swrm_get_device_status(ctrl);
-	sdw_handle_slave_status(&ctrl->bus, ctrl->status);
-}
-
-
 static void qcom_swrm_stream_free_ports(struct qcom_swrm_ctrl *ctrl,
 					struct sdw_stream_runtime *stream)
 {
@@ -928,9 +949,8 @@ static int qcom_swrm_probe(struct platform_device *pdev)
 
 	ctrl->dev = dev;
 	dev_set_drvdata(&pdev->dev, ctrl);
-	spin_lock_init(&ctrl->comp_lock);
 	mutex_init(&ctrl->port_lock);
-	INIT_WORK(&ctrl->slave_work, qcom_swrm_slave_wq);
+	init_completion(&ctrl->broadcast);
 
 	ctrl->bus.ops = &qcom_swrm_ops;
 	ctrl->bus.port_ops = &qcom_swrm_port_ops;
-- 
2.21.0

[PATCH v3 6/9] soundwire: qcom: add support to new interrupts

[Srinivas Kandagatla]

Add support to new interrupts which includes reporting some of the
error interrupts and adding support to SLAVE pending interrupt!

This patch also changes the interrupt handler behaviour on handling
any pending interrupts by checking it before returning out of irq handler.

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
---
 drivers/soundwire/qcom.c | 161 ++++++++++++++++++++++++++++++++-------
 1 file changed, 135 insertions(+), 26 deletions(-)

diff --git a/drivers/soundwire/qcom.c b/drivers/soundwire/qcom.c
index 7762ff237636..2a53da521626 100644
--- a/drivers/soundwire/qcom.c
+++ b/drivers/soundwire/qcom.c
@@ -28,10 +28,21 @@
 #define SWRM_COMP_PARAMS_DIN_PORTS_MASK				GENMASK(9, 5)
 #define SWRM_INTERRUPT_STATUS					0x200
 #define SWRM_INTERRUPT_STATUS_RMSK				GENMASK(16, 0)
+#define SWRM_INTERRUPT_STATUS_SLAVE_PEND_IRQ			BIT(0)
 #define SWRM_INTERRUPT_STATUS_NEW_SLAVE_ATTACHED		BIT(1)
 #define SWRM_INTERRUPT_STATUS_CHANGE_ENUM_SLAVE_STATUS		BIT(2)
+#define SWRM_INTERRUPT_STATUS_MASTER_CLASH_DET			BIT(3)
+#define SWRM_INTERRUPT_STATUS_RD_FIFO_OVERFLOW			BIT(4)
+#define SWRM_INTERRUPT_STATUS_RD_FIFO_UNDERFLOW			BIT(5)
+#define SWRM_INTERRUPT_STATUS_WR_CMD_FIFO_OVERFLOW		BIT(6)
 #define SWRM_INTERRUPT_STATUS_CMD_ERROR				BIT(7)
+#define SWRM_INTERRUPT_STATUS_DOUT_PORT_COLLISION		BIT(8)
+#define SWRM_INTERRUPT_STATUS_READ_EN_RD_VALID_MISMATCH		BIT(9)
 #define SWRM_INTERRUPT_STATUS_SPECIAL_CMD_ID_FINISHED		BIT(10)
+#define SWRM_INTERRUPT_STATUS_BUS_RESET_FINISHED_V2             BIT(13)
+#define SWRM_INTERRUPT_STATUS_CLK_STOP_FINISHED_V2              BIT(14)
+#define SWRM_INTERRUPT_STATUS_EXT_CLK_STOP_WAKEUP               BIT(16)
+#define SWRM_INTERRUPT_MAX					17
 #define SWRM_INTERRUPT_MASK_ADDR				0x204
 #define SWRM_INTERRUPT_CLEAR					0x208
 #define SWRM_INTERRUPT_CPU_EN					0x210
@@ -58,6 +69,7 @@
 #define SWRM_MCP_STATUS_BANK_NUM_MASK				BIT(0)
 #define SWRM_MCP_SLV_STATUS					0x1090
 #define SWRM_MCP_SLV_STATUS_MASK				GENMASK(1, 0)
+#define SWRM_MCP_SLV_STATUS_SZ					2
 #define SWRM_DP_PORT_CTRL_BANK(n, m)	(0x1124 + 0x100 * (n - 1) + 0x40 * m)
 #define SWRM_DP_PORT_CTRL_2_BANK(n, m)	(0x1128 + 0x100 * (n - 1) + 0x40 * m)
 #define SWRM_DP_BLOCK_CTRL_1(n)		(0x112C + 0x100 * (n - 1))
@@ -123,6 +135,7 @@ struct qcom_swrm_ctrl {
 	int rows_index;
 	unsigned long dout_port_mask;
 	unsigned long din_port_mask;
+	u32 intr_mask;
 	u8 rcmd_id;
 	u8 wcmd_id;
 	struct qcom_swrm_port_config pconfig[QCOM_SDW_MAX_PORTS];
@@ -304,6 +317,25 @@ static int qcom_swrm_cmd_fifo_rd_cmd(struct qcom_swrm_ctrl *swrm,
 	return SDW_CMD_IGNORED;
 }
 
+static int qcom_swrm_get_alert_slave_dev_num(struct qcom_swrm_ctrl *ctrl)
+{
+	u32 val, status;
+	int dev_num;
+
+	ctrl->reg_read(ctrl, SWRM_MCP_SLV_STATUS, &val);
+
+	for (dev_num = 0; dev_num < SDW_MAX_DEVICES; dev_num++) {
+		status = (val >> (dev_num * SWRM_MCP_SLV_STATUS_SZ));
+
+		if ((status & SWRM_MCP_SLV_STATUS_MASK) == SDW_SLAVE_ALERT) {
+			ctrl->status[dev_num] = status;
+			return dev_num;
+		}
+	}
+
+	return -EINVAL;
+}
+
 static void qcom_swrm_get_device_status(struct qcom_swrm_ctrl *ctrl)
 {
 	u32 val;
@@ -322,36 +354,112 @@ static void qcom_swrm_get_device_status(struct qcom_swrm_ctrl *ctrl)
 
 static irqreturn_t qcom_swrm_irq_handler(int irq, void *dev_id)
 {
-	struct qcom_swrm_ctrl *ctrl = dev_id;
-	u32 sts, value;
+	struct qcom_swrm_ctrl *swrm = dev_id;
+	u32 value, intr_sts, intr_sts_masked;
+	u32 i;
+	u8 devnum = 0;
+	int ret = IRQ_HANDLED;
 
-	ctrl->reg_read(ctrl, SWRM_INTERRUPT_STATUS, &sts);
+	swrm->reg_read(swrm, SWRM_INTERRUPT_STATUS, &intr_sts);
+	intr_sts_masked = intr_sts & swrm->intr_mask;
 
-	if (sts & SWRM_INTERRUPT_STATUS_CMD_ERROR) {
-		ctrl->reg_read(ctrl, SWRM_CMD_FIFO_STATUS, &value);
-		dev_err_ratelimited(ctrl->dev,
-				    "CMD error, fifo status 0x%x\n",
-				     value);
-		ctrl->reg_write(ctrl, SWRM_CMD_FIFO_CMD, 0x1);
-	}
-
-	if ((sts & SWRM_INTERRUPT_STATUS_NEW_SLAVE_ATTACHED) ||
-	    sts & SWRM_INTERRUPT_STATUS_CHANGE_ENUM_SLAVE_STATUS) {
-		qcom_swrm_get_device_status(ctrl);
-		sdw_handle_slave_status(&ctrl->bus, ctrl->status);
-	}
-
-	/**
-	 * clear the interrupt before complete() is called, as complete can
-	 * schedule new read/writes which require interrupts, clearing the
-	 * interrupt would avoid missing interrupts in such cases.
-	 */
-	ctrl->reg_write(ctrl, SWRM_INTERRUPT_CLEAR, sts);
+	do {
+		for (i = 0; i < SWRM_INTERRUPT_MAX; i++) {
+			value = intr_sts_masked & (1 << i);
+			if (!value)
+				continue;
+
+			switch (value) {
+			case SWRM_INTERRUPT_STATUS_SLAVE_PEND_IRQ:
+				devnum = qcom_swrm_get_alert_slave_dev_num(swrm);
+				if (devnum < 0) {
+					dev_err_ratelimited(swrm->dev,
+					    "no slave alert found.spurious interrupt\n");
+				} else {
+					sdw_handle_slave_status(&swrm->bus, swrm->status);
+				}
 
-	if (sts & SWRM_INTERRUPT_STATUS_SPECIAL_CMD_ID_FINISHED)
-		complete(&ctrl->broadcast);
+				break;
+			case SWRM_INTERRUPT_STATUS_NEW_SLAVE_ATTACHED:
+			case SWRM_INTERRUPT_STATUS_CHANGE_ENUM_SLAVE_STATUS:
+				dev_err_ratelimited(swrm->dev, "%s: SWR new slave attached\n",
+					__func__);
+				qcom_swrm_get_device_status(swrm);
+				sdw_handle_slave_status(&swrm->bus, swrm->status);
+				break;
+			case SWRM_INTERRUPT_STATUS_MASTER_CLASH_DET:
+				dev_err_ratelimited(swrm->dev,
+						"%s: SWR bus clsh detected\n",
+						__func__);
+				swrm->intr_mask &= ~SWRM_INTERRUPT_STATUS_MASTER_CLASH_DET;
+				swrm->reg_write(swrm, SWRM_INTERRUPT_CPU_EN, swrm->intr_mask);
+				break;
+			case SWRM_INTERRUPT_STATUS_RD_FIFO_OVERFLOW:
+				swrm->reg_read(swrm, SWRM_CMD_FIFO_STATUS, &value);
+				dev_err_ratelimited(swrm->dev,
+					"%s: SWR read FIFO overflow fifo status 0x%x\n",
+					__func__, value);
+				break;
+			case SWRM_INTERRUPT_STATUS_RD_FIFO_UNDERFLOW:
+				swrm->reg_read(swrm, SWRM_CMD_FIFO_STATUS, &value);
+				dev_err_ratelimited(swrm->dev,
+					"%s: SWR read FIFO underflow fifo status 0x%x\n",
+					__func__, value);
+				break;
+			case SWRM_INTERRUPT_STATUS_WR_CMD_FIFO_OVERFLOW:
+				swrm->reg_read(swrm, SWRM_CMD_FIFO_STATUS, &value);
+				dev_err(swrm->dev,
+					"%s: SWR write FIFO overflow fifo status %x\n",
+					__func__, value);
+				swrm->reg_write(swrm, SWRM_CMD_FIFO_CMD, 0x1);
+				break;
+			case SWRM_INTERRUPT_STATUS_CMD_ERROR:
+				swrm->reg_read(swrm, SWRM_CMD_FIFO_STATUS, &value);
+				dev_err_ratelimited(swrm->dev,
+					"%s: SWR CMD error, fifo status 0x%x, flushing fifo\n",
+					__func__, value);
+				swrm->reg_write(swrm, SWRM_CMD_FIFO_CMD, 0x1);
+				break;
+			case SWRM_INTERRUPT_STATUS_DOUT_PORT_COLLISION:
+				dev_err_ratelimited(swrm->dev,
+						"%s: SWR Port collision detected\n",
+						__func__);
+				swrm->intr_mask &= ~SWRM_INTERRUPT_STATUS_DOUT_PORT_COLLISION;
+				swrm->reg_write(swrm,
+					SWRM_INTERRUPT_CPU_EN, swrm->intr_mask);
+				break;
+			case SWRM_INTERRUPT_STATUS_READ_EN_RD_VALID_MISMATCH:
+				dev_err_ratelimited(swrm->dev,
+					"%s: SWR read enable valid mismatch\n",
+					__func__);
+				swrm->intr_mask &=
+					~SWRM_INTERRUPT_STATUS_READ_EN_RD_VALID_MISMATCH;
+				swrm->reg_write(swrm,
+					SWRM_INTERRUPT_CPU_EN, swrm->intr_mask);
+				break;
+			case SWRM_INTERRUPT_STATUS_SPECIAL_CMD_ID_FINISHED:
+				complete(&swrm->broadcast);
+				break;
+			case SWRM_INTERRUPT_STATUS_BUS_RESET_FINISHED_V2:
+				break;
+			case SWRM_INTERRUPT_STATUS_CLK_STOP_FINISHED_V2:
+				break;
+			case SWRM_INTERRUPT_STATUS_EXT_CLK_STOP_WAKEUP:
+				break;
+			default:
+				dev_err_ratelimited(swrm->dev,
+						"%s: SWR unknown interrupt value: %d\n",
+						__func__, value);
+				ret = IRQ_NONE;
+				break;
+			}
+		}
+		swrm->reg_write(swrm, SWRM_INTERRUPT_CLEAR, intr_sts);
+		swrm->reg_read(swrm, SWRM_INTERRUPT_STATUS, &intr_sts);
+		intr_sts_masked = intr_sts & swrm->intr_mask;
+	} while (intr_sts_masked);
 
-	return IRQ_HANDLED;
+	return ret;
 }
 
 static int qcom_swrm_init(struct qcom_swrm_ctrl *ctrl)
@@ -367,6 +475,7 @@ static int qcom_swrm_init(struct qcom_swrm_ctrl *ctrl)
 	/* Disable Auto enumeration */
 	ctrl->reg_write(ctrl, SWRM_ENUMERATOR_CFG_ADDR, 0);
 
+	ctrl->intr_mask = SWRM_INTERRUPT_STATUS_RMSK;
 	/* Mask soundwire interrupts */
 	ctrl->reg_write(ctrl, SWRM_INTERRUPT_MASK_ADDR,
 			SWRM_INTERRUPT_STATUS_RMSK);
-- 
2.21.0

[PATCH v3 7/9] soundwire: export sdw_compare_devid() and sdw_extract_slave_id()

[Srinivas Kandagatla]

Exporting these two functions makes sense as it can be used by
other controllers like Qualcomm during auto-enumeration!

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
---
 drivers/soundwire/bus.c       | 4 +++-
 include/linux/soundwire/sdw.h | 2 ++
 2 files changed, 5 insertions(+), 1 deletion(-)

diff --git a/drivers/soundwire/bus.c b/drivers/soundwire/bus.c
index 48577b78f282..46d3407c097f 100644
--- a/drivers/soundwire/bus.c
+++ b/drivers/soundwire/bus.c
@@ -608,7 +608,7 @@ static struct sdw_slave *sdw_get_slave(struct sdw_bus *bus, int i)
 	return NULL;
 }
 
-static int sdw_compare_devid(struct sdw_slave *slave, struct sdw_slave_id id)
+int sdw_compare_devid(struct sdw_slave *slave, struct sdw_slave_id id)
 {
 	if (slave->id.mfg_id != id.mfg_id ||
 	    slave->id.part_id != id.part_id ||
@@ -619,6 +619,7 @@ static int sdw_compare_devid(struct sdw_slave *slave, struct sdw_slave_id id)
 
 	return 0;
 }
+EXPORT_SYMBOL(sdw_compare_devid);
 
 /* called with bus_lock held */
 static int sdw_get_device_num(struct sdw_slave *slave)
@@ -703,6 +704,7 @@ void sdw_extract_slave_id(struct sdw_bus *bus,
 		"SDW Slave class_id 0x%02x, mfg_id 0x%04x, part_id 0x%04x, unique_id 0x%x, version 0x%x\n",
 		id->class_id, id->mfg_id, id->part_id, id->unique_id, id->sdw_version);
 }
+EXPORT_SYMBOL(sdw_extract_slave_id);
 
 static int sdw_program_device_num(struct sdw_bus *bus)
 {
diff --git a/include/linux/soundwire/sdw.h b/include/linux/soundwire/sdw.h
index d08039d65825..8478a1f5f833 100644
--- a/include/linux/soundwire/sdw.h
+++ b/include/linux/soundwire/sdw.h
@@ -1009,5 +1009,7 @@ int sdw_write_no_pm(struct sdw_slave *slave, u32 addr, u8 value);
 int sdw_read_no_pm(struct sdw_slave *slave, u32 addr);
 int sdw_nread(struct sdw_slave *slave, u32 addr, size_t count, u8 *val);
 int sdw_nwrite(struct sdw_slave *slave, u32 addr, size_t count, u8 *val);
+int sdw_compare_devid(struct sdw_slave *slave, struct sdw_slave_id id);
+void sdw_extract_slave_id(struct sdw_bus *bus, u64 addr, struct sdw_slave_id *id);
 
 #endif /* __SOUNDWIRE_H */
-- 
2.21.0

[PATCH v3 8/9] soundwire: qcom: add auto enumeration support

[Srinivas Kandagatla]

Qualcomm SoundWire controller supports Auto Enumeration of the
devices within the IP. This patch enables support for this feature.

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
---
 drivers/soundwire/qcom.c | 84 +++++++++++++++++++++++++++++++++++++---
 1 file changed, 79 insertions(+), 5 deletions(-)

diff --git a/drivers/soundwire/qcom.c b/drivers/soundwire/qcom.c
index 2a53da521626..3109ec6c33ac 100644
--- a/drivers/soundwire/qcom.c
+++ b/drivers/soundwire/qcom.c
@@ -57,6 +57,8 @@
 #define SWRM_CMD_FIFO_RD_FIFO_ADDR				0x318
 #define SWRM_RD_FIFO_CMD_ID_MASK				GENMASK(11, 8)
 #define SWRM_ENUMERATOR_CFG_ADDR				0x500
+#define SWRM_ENUMERATOR_SLAVE_DEV_ID_1(m)		(0x530 + 0x8 * (m))
+#define SWRM_ENUMERATOR_SLAVE_DEV_ID_2(m)		(0x534 + 0x8 * (m))
 #define SWRM_MCP_FRAME_CTRL_BANK_ADDR(m)		(0x101C + 0x40 * (m))
 #define SWRM_MCP_FRAME_CTRL_BANK_COL_CTRL_BMSK			GENMASK(2, 0)
 #define SWRM_MCP_FRAME_CTRL_BANK_ROW_CTRL_BMSK			GENMASK(7, 3)
@@ -143,6 +145,7 @@ struct qcom_swrm_ctrl {
 	enum sdw_slave_status status[SDW_MAX_DEVICES];
 	int (*reg_read)(struct qcom_swrm_ctrl *ctrl, int reg, u32 *val);
 	int (*reg_write)(struct qcom_swrm_ctrl *ctrl, int reg, int val);
+	u32 slave_status;
 };
 
 struct qcom_swrm_data {
@@ -342,6 +345,7 @@ static void qcom_swrm_get_device_status(struct qcom_swrm_ctrl *ctrl)
 	int i;
 
 	ctrl->reg_read(ctrl, SWRM_MCP_SLV_STATUS, &val);
+	ctrl->slave_status = val;
 
 	for (i = 0; i < SDW_MAX_DEVICES; i++) {
 		u32 s;
@@ -352,10 +356,72 @@ static void qcom_swrm_get_device_status(struct qcom_swrm_ctrl *ctrl)
 	}
 }
 
+static int qcom_swrm_get_n_device_status(struct qcom_swrm_ctrl *ctrl, int devnum)
+{
+	u32 val;
+
+	ctrl->reg_read(ctrl, SWRM_MCP_SLV_STATUS, &val);
+	val = (val >> (devnum * SWRM_MCP_SLV_STATUS_SZ));
+	val &= SWRM_MCP_SLV_STATUS_MASK;
+
+	return val;
+}
+
+static int qcom_swrm_enumerate(struct sdw_bus *bus)
+{
+	struct qcom_swrm_ctrl *ctrl = to_qcom_sdw(bus);
+	struct sdw_slave *slave, *_s;
+	struct sdw_slave_id id;
+	u32 val1, val2;
+	bool found;
+	u64 addr;
+	int i;
+	char *buf1 = (char *)&val1, *buf2 = (char *)&val2;
+
+	for (i = 1; i <= SDW_MAX_DEVICES; i++) {
+		/*SCP_Devid5 - Devid 4*/
+		ctrl->reg_read(ctrl, SWRM_ENUMERATOR_SLAVE_DEV_ID_1(i), &val1);
+
+		/*SCP_Devid3 - DevId 2 Devid 1 Devid 0*/
+		ctrl->reg_read(ctrl, SWRM_ENUMERATOR_SLAVE_DEV_ID_2(i), &val2);
+
+		if (!val1 && !val2)
+			break;
+
+		addr = buf2[1] | (buf2[0] << 8) | (buf1[3] << 16) |
+			((u64)buf1[2] << 24) | ((u64)buf1[1] << 32) |
+			((u64)buf1[0] << 40);
+
+		sdw_extract_slave_id(bus, addr, &id);
+		found = false;
+		/* Now compare with entries */
+		list_for_each_entry_safe(slave, _s, &bus->slaves, node) {
+			if (sdw_compare_devid(slave, id) == 0) {
+				u32 status = qcom_swrm_get_n_device_status(ctrl, i);
+
+				found = true;
+				if (status == SDW_SLAVE_ATTACHED) {
+					slave->dev_num = i;
+					mutex_lock(&bus->bus_lock);
+					set_bit(i, bus->assigned);
+					mutex_unlock(&bus->bus_lock);
+
+				}
+				break;
+			}
+		}
+
+		if (!found)
+			sdw_slave_add(bus, &id, NULL);
+	}
+
+	return 0;
+}
+
 static irqreturn_t qcom_swrm_irq_handler(int irq, void *dev_id)
 {
 	struct qcom_swrm_ctrl *swrm = dev_id;
-	u32 value, intr_sts, intr_sts_masked;
+	u32 value, intr_sts, intr_sts_masked, slave_status;
 	u32 i;
 	u8 devnum = 0;
 	int ret = IRQ_HANDLED;
@@ -384,8 +450,15 @@ static irqreturn_t qcom_swrm_irq_handler(int irq, void *dev_id)
 			case SWRM_INTERRUPT_STATUS_CHANGE_ENUM_SLAVE_STATUS:
 				dev_err_ratelimited(swrm->dev, "%s: SWR new slave attached\n",
 					__func__);
-				qcom_swrm_get_device_status(swrm);
-				sdw_handle_slave_status(&swrm->bus, swrm->status);
+				swrm->reg_read(swrm, SWRM_MCP_SLV_STATUS, &slave_status);
+				if (swrm->slave_status == slave_status) {
+					dev_err(swrm->dev, "Slave status not changed %x\n",
+						slave_status);
+				} else {
+					qcom_swrm_get_device_status(swrm);
+					qcom_swrm_enumerate(&swrm->bus);
+					sdw_handle_slave_status(&swrm->bus, swrm->status);
+				}
 				break;
 			case SWRM_INTERRUPT_STATUS_MASTER_CLASH_DET:
 				dev_err_ratelimited(swrm->dev,
@@ -472,8 +545,8 @@ static int qcom_swrm_init(struct qcom_swrm_ctrl *ctrl)
 
 	ctrl->reg_write(ctrl, SWRM_MCP_FRAME_CTRL_BANK_ADDR(0), val);
 
-	/* Disable Auto enumeration */
-	ctrl->reg_write(ctrl, SWRM_ENUMERATOR_CFG_ADDR, 0);
+	/* Enable Auto enumeration */
+	ctrl->reg_write(ctrl, SWRM_ENUMERATOR_CFG_ADDR, 1);
 
 	ctrl->intr_mask = SWRM_INTERRUPT_STATUS_RMSK;
 	/* Mask soundwire interrupts */
@@ -507,6 +580,7 @@ static int qcom_swrm_init(struct qcom_swrm_ctrl *ctrl)
 		ctrl->reg_write(ctrl, SWRM_INTERRUPT_CPU_EN,
 				SWRM_INTERRUPT_STATUS_RMSK);
 	}
+	ctrl->slave_status = 0;
 	return 0;
 }
 
-- 
2.21.0

Re: [PATCH v3 8/9] soundwire: qcom: add auto enumeration support

[Pierre-Louis Bossart]

> +static int qcom_swrm_enumerate(struct sdw_bus *bus)
> +{
> +	struct qcom_swrm_ctrl *ctrl = to_qcom_sdw(bus);
> +	struct sdw_slave *slave, *_s;
> +	struct sdw_slave_id id;
> +	u32 val1, val2;
> +	bool found;
> +	u64 addr;
> +	int i;
> +	char *buf1 = (char *)&val1, *buf2 = (char *)&val2;
> +
> +	for (i = 1; i <= SDW_MAX_DEVICES; i++) {
> +		/*SCP_Devid5 - Devid 4*/
> +		ctrl->reg_read(ctrl, SWRM_ENUMERATOR_SLAVE_DEV_ID_1(i), &val1);
> +
> +		/*SCP_Devid3 - DevId 2 Devid 1 Devid 0*/
> +		ctrl->reg_read(ctrl, SWRM_ENUMERATOR_SLAVE_DEV_ID_2(i), &val2);
> +
> +		if (!val1 && !val2)
> +			break;
> +
> +		addr = buf2[1] | (buf2[0] << 8) | (buf1[3] << 16) |
> +			((u64)buf1[2] << 24) | ((u64)buf1[1] << 32) |
> +			((u64)buf1[0] << 40);
> +
> +		sdw_extract_slave_id(bus, addr, &id);
> +		found = false;
> +		/* Now compare with entries */
> +		list_for_each_entry_safe(slave, _s, &bus->slaves, node) {
> +			if (sdw_compare_devid(slave, id) == 0) {
> +				u32 status = qcom_swrm_get_n_device_status(ctrl, i);
> +
> +				found = true;
> +				if (status == SDW_SLAVE_ATTACHED) {
> +					slave->dev_num = i;
> +					mutex_lock(&bus->bus_lock);
> +					set_bit(i, bus->assigned);
> +					mutex_unlock(&bus->bus_lock);
> +
> +				}

you haven't changed that part, if the device is not in DT we should 
still set bus->assigned::i

Re: [PATCH v3 8/9] soundwire: qcom: add auto enumeration support

[Srinivas Kandagatla]

On 08/03/2021 15:56, Pierre-Louis Bossart wrote:
> 
>> +static int qcom_swrm_enumerate(struct sdw_bus *bus)
>> +{
>> +    struct qcom_swrm_ctrl *ctrl = to_qcom_sdw(bus);
>> +    struct sdw_slave *slave, *_s;
>> +    struct sdw_slave_id id;
>> +    u32 val1, val2;
>> +    bool found;
>> +    u64 addr;
>> +    int i;
>> +    char *buf1 = (char *)&val1, *buf2 = (char *)&val2;
>> +
>> +    for (i = 1; i <= SDW_MAX_DEVICES; i++) {
>> +        /*SCP_Devid5 - Devid 4*/
>> +        ctrl->reg_read(ctrl, SWRM_ENUMERATOR_SLAVE_DEV_ID_1(i), &val1);
>> +
>> +        /*SCP_Devid3 - DevId 2 Devid 1 Devid 0*/
>> +        ctrl->reg_read(ctrl, SWRM_ENUMERATOR_SLAVE_DEV_ID_2(i), &val2);
>> +
>> +        if (!val1 && !val2)
>> +            break;
>> +
>> +        addr = buf2[1] | (buf2[0] << 8) | (buf1[3] << 16) |
>> +            ((u64)buf1[2] << 24) | ((u64)buf1[1] << 32) |
>> +            ((u64)buf1[0] << 40);
>> +
>> +        sdw_extract_slave_id(bus, addr, &id);
>> +        found = false;
>> +        /* Now compare with entries */
>> +        list_for_each_entry_safe(slave, _s, &bus->slaves, node) {
>> +            if (sdw_compare_devid(slave, id) == 0) {
>> +                u32 status = qcom_swrm_get_n_device_status(ctrl, i);
>> +
>> +                found = true;
>> +                if (status == SDW_SLAVE_ATTACHED) {
>> +                    slave->dev_num = i;
>> +                    mutex_lock(&bus->bus_lock);
>> +                    set_bit(i, bus->assigned);
>> +                    mutex_unlock(&bus->bus_lock);
>> +
>> +                }
> 
> you haven't changed that part, if the device is not in DT we should 
> still set bus->assigned::i

My bad! I missed it again!

Will fix it in next spin!


--srini

[PATCH v3 9/9] soundwire: qcom: wait for enumeration to be complete in probe

[Srinivas Kandagatla]

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
---
 drivers/soundwire/qcom.c | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/drivers/soundwire/qcom.c b/drivers/soundwire/qcom.c
index 3109ec6c33ac..578a392bfbee 100644
--- a/drivers/soundwire/qcom.c
+++ b/drivers/soundwire/qcom.c
@@ -123,6 +123,7 @@ struct qcom_swrm_ctrl {
 	struct regmap *regmap;
 	void __iomem *mmio;
 	struct completion broadcast;
+	struct completion enumeration;
 	struct work_struct slave_work;
 	/* Port alloc/free lock */
 	struct mutex port_lock;
@@ -415,6 +416,7 @@ static int qcom_swrm_enumerate(struct sdw_bus *bus)
 			sdw_slave_add(bus, &id, NULL);
 	}
 
+	complete(&ctrl->enumeration);
 	return 0;
 }
 
@@ -1134,6 +1136,7 @@ static int qcom_swrm_probe(struct platform_device *pdev)
 	dev_set_drvdata(&pdev->dev, ctrl);
 	mutex_init(&ctrl->port_lock);
 	init_completion(&ctrl->broadcast);
+	init_completion(&ctrl->enumeration);
 
 	ctrl->bus.ops = &qcom_swrm_ops;
 	ctrl->bus.port_ops = &qcom_swrm_port_ops;
@@ -1180,6 +1183,8 @@ static int qcom_swrm_probe(struct platform_device *pdev)
 	}
 
 	qcom_swrm_init(ctrl);
+	wait_for_completion_timeout(&ctrl->enumeration,
+				    msecs_to_jiffies(TIMEOUT_MS));
 	ret = qcom_swrm_register_dais(ctrl);
 	if (ret)
 		goto err_master_add;
-- 
2.21.0