[PATCH v8 0/3] J7200: Add support for GPIO and higher speed modes in MMCSD subsystems

[PATCH v8 0/3] J7200: Add support for GPIO and higher speed modes in MMCSD subsystems

[Aswath Govindraju]

The following series of patches
- Add support for GPIO subsystem in main and wakeup domains.
- Add voltage regulator device tree nodes and their corresponding pinmux
  to support power cycle and voltage switch required for UHS-I modes
- sets respective tags in sdhci0 node to support higher speeds
- remove no-1-8-v tag from sdhci1 node to support UHS-I modes
- Update delay values for various speed modes supported.


test logs
- eMMC HS400 speed mode
  https://pastebin.ubuntu.com/p/pRzV2ZvSJZ/

- SD SDR104 speed mode
  https://pastebin.ubuntu.com/p/n64PNdDy2v/  
  
- GPIO logs
  https://pastebin.ubuntu.com/p/HDBBMwMcdj/

Changes since v7:
- Added the voltage regulator nodes to indicate the complete
  power flow for MMCSD1 subsystem
- Corrected minor errors in DT nodes
- Reran the tests.
- Rebased the series

Changes since v6:
- Corrected the node name from vdd_sd_dv_pins_default to
  vdd-sd-dv-pins-default

Changes since v5:
- Corrected the link in patch 3 as it broken.
- Added the version number for the references used in patch 3.
- picked up reviewed-by from grygorii for patches 1 and 2.

Changes since v4:
- Added main_i2c0 pinmux required for doing power cycles to MMCSD1
  subsystem
- Updated delay values for various speed modes supported
- Corrected the ti,ngpio property to indicate highest gpio lines that
  can be accessed.
- Reran the performace tests

Changes since v3:
- Removed patch (1 in v3).
- Rebased and included patches that add support for GPIO from series [1].
- Re-ran the performace tests for SD and eMMC.

Changes since v2:
- Added main_gpio0 DT node
- Added voltage regulator device tree nodes required to support UHS-I modes

Changes since v1:
- squashed the two patches into one
- added performance logs for the above mentioned speed modes


Aswath Govindraju (1):
  arm64: dts: ti: k3-j7200: Add support for higher speed modes and
    update delay select values for MMCSD subsystems

Faiz Abbas (2):
  arm64: dts: ti: k3-j7200: Add gpio nodes
  arm64: dts: ti: k3-j7200-common-proc-board: Disable unused gpio
    modules

 .../dts/ti/k3-j7200-common-proc-board.dts     | 94 +++++++++++++++++++
 arch/arm64/boot/dts/ti/k3-j7200-main.dtsi     | 86 ++++++++++++++++-
 .../boot/dts/ti/k3-j7200-mcu-wakeup.dtsi      | 34 +++++++
 3 files changed, 212 insertions(+), 2 deletions(-)

-- 
2.17.1

[PATCH v8 1/3] arm64: dts: ti: k3-j7200: Add gpio nodes

[Aswath Govindraju]

From: Faiz Abbas <faiz_abbas@ti.com>

There are 4 instances of gpio modules in main domain:
	gpio0, gpio2, gpio4 and gpio6

Groups are created to provide protection between different processor
virtual worlds. Each of these modules I/O pins are muxed within the
group. Exactly one module can be selected to control the corresponding
pin by selecting it in the pad mux configuration registers.

This group in main domain pins out 69 lines (5 banks). Add DT modes for
each module instance in the main domain.

Similar to the gpio groups in main domain, there is one gpio group in
wakeup domain with 2 module instances in it.

The gpio group pins out 72 pins (6 banks) of the first 85 gpio lines. Add
DT nodes for each module instance in the wakeup domain.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
---
 arch/arm64/boot/dts/ti/k3-j7200-main.dtsi     | 72 +++++++++++++++++++
 .../boot/dts/ti/k3-j7200-mcu-wakeup.dtsi      | 34 +++++++++
 2 files changed, 106 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
index 17477ab0fd8e..e60650a62b14 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
@@ -672,6 +672,78 @@
 		};
 	};
 
+	main_gpio0: gpio@600000 {
+		compatible = "ti,j721e-gpio", "ti,keystone-gpio";
+		reg = <0x00 0x00600000 0x00 0x100>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&main_gpio_intr>;
+		interrupts = <145>, <146>, <147>, <148>,
+			     <149>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		#address-cells = <0>;
+		ti,ngpio = <69>;
+		ti,davinci-gpio-unbanked = <0>;
+		power-domains = <&k3_pds 105 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 105 0>;
+		clock-names = "gpio";
+	};
+
+	main_gpio2: gpio@610000 {
+		compatible = "ti,j721e-gpio", "ti,keystone-gpio";
+		reg = <0x00 0x00610000 0x00 0x100>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&main_gpio_intr>;
+		interrupts = <154>, <155>, <156>, <157>,
+			     <158>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		#address-cells = <0>;
+		ti,ngpio = <69>;
+		ti,davinci-gpio-unbanked = <0>;
+		power-domains = <&k3_pds 107 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 107 0>;
+		clock-names = "gpio";
+	};
+
+	main_gpio4: gpio@620000 {
+		compatible = "ti,j721e-gpio", "ti,keystone-gpio";
+		reg = <0x00 0x00620000 0x00 0x100>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&main_gpio_intr>;
+		interrupts = <163>, <164>, <165>, <166>,
+			     <167>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		#address-cells = <0>;
+		ti,ngpio = <69>;
+		ti,davinci-gpio-unbanked = <0>;
+		power-domains = <&k3_pds 109 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 109 0>;
+		clock-names = "gpio";
+	};
+
+	main_gpio6: gpio@630000 {
+		compatible = "ti,j721e-gpio", "ti,keystone-gpio";
+		reg = <0x00 0x00630000 0x00 0x100>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&main_gpio_intr>;
+		interrupts = <172>, <173>, <174>, <175>,
+			     <176>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		#address-cells = <0>;
+		ti,ngpio = <69>;
+		ti,davinci-gpio-unbanked = <0>;
+		power-domains = <&k3_pds 111 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 111 0>;
+		clock-names = "gpio";
+	};
+
 	main_r5fss0: r5fss@5c00000 {
 		compatible = "ti,j7200-r5fss";
 		ti,cluster-mode = <1>;
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi
index 5408ec815d58..4e4ea7655fe2 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi
@@ -107,6 +107,40 @@
 		ti,interrupt-ranges = <16 960 16>;
 	};
 
+	wkup_gpio0: gpio@42110000 {
+		compatible = "ti,j721e-gpio", "ti,keystone-gpio";
+		reg = <0x00 0x42110000 0x00 0x100>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&wkup_gpio_intr>;
+		interrupts = <103>, <104>, <105>, <106>, <107>, <108>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		#address-cells = <0>;
+		ti,ngpio = <85>;
+		ti,davinci-gpio-unbanked = <0>;
+		power-domains = <&k3_pds 113 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 113 0>;
+		clock-names = "gpio";
+	};
+
+	wkup_gpio1: gpio@42100000 {
+		compatible = "ti,j721e-gpio", "ti,keystone-gpio";
+		reg = <0x00 0x42100000 0x00 0x100>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&wkup_gpio_intr>;
+		interrupts = <112>, <113>, <114>, <115>, <116>, <117>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		#address-cells = <0>;
+		ti,ngpio = <85>;
+		ti,davinci-gpio-unbanked = <0>;
+		power-domains = <&k3_pds 114 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 114 0>;
+		clock-names = "gpio";
+	};
+
 	mcu_navss: bus@28380000 {
 		compatible = "simple-mfd";
 		#address-cells = <2>;
-- 
2.17.1

[PATCH v8 2/3] arm64: dts: ti: k3-j7200-common-proc-board: Disable unused gpio modules

[Aswath Govindraju]

From: Faiz Abbas <faiz_abbas@ti.com>

There are 6 gpio instances inside SoC with 2 groups as show below:
    Group one: wkup_gpio0, wkup_gpio1
    Group two: main_gpio0, main_gpio2, main_gpio4, main_gpio6

Only one instance from each group can be used at a time. So use main_gpio0
and wkup_gpio0 in current linux context and disable the rest of the nodes.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
---
 .../boot/dts/ti/k3-j7200-common-proc-board.dts   | 16 ++++++++++++++++
 1 file changed, 16 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
index 4a7182abccf5..b493f939b09a 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
@@ -122,6 +122,22 @@
 	status = "disabled";
 };
 
+&main_gpio2 {
+	status = "disabled";
+};
+
+&main_gpio4 {
+	status = "disabled";
+};
+
+&main_gpio6 {
+	status = "disabled";
+};
+
+&wkup_gpio1 {
+	status = "disabled";
+};
+
 &mcu_cpsw {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mcu_cpsw_pins_default &mcu_mdio_pins_default>;
-- 
2.17.1

[PATCH v8 3/3] arm64: dts: ti: k3-j7200: Add support for higher speed modes and update delay select values for MMCSD subsystems

[Aswath Govindraju]

The following speed modes are now supported in J7200 SoC,
- HS200 and HS400 modes at 1.8 V card voltage, in MMCSD0 subsystem [1].
- UHS-I speed modes in MMCSD1 subsystem [1].

Add support for UHS-I modes by adding voltage regulator device tree nodes
and corresponding pinmux details, to power cycle and voltage switch cards.
Set respective tags in sdhci0 and remove no-1-8-v tag from sdhci1
device tree nodes.

Also update the delay values for various speed modes supported, based on
the revised january 2021 J7200 datasheet[2].

[1] - section 12.3.6.1.1 MMCSD Features, in
      https://www.ti.com/lit/ug/spruiu1a/spruiu1a.pdf,
      (SPRUIU1A – JULY 2020 – REVISED JANUARY 2021)

[2] - https://www.ti.com/lit/ds/symlink/dra821u.pdf,
      (SPRSP57B – APRIL 2020 – REVISED JANUARY 2021)

Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
---
 .../dts/ti/k3-j7200-common-proc-board.dts     | 78 +++++++++++++++++++
 arch/arm64/boot/dts/ti/k3-j7200-main.dtsi     | 14 +++-
 2 files changed, 90 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
index b493f939b09a..a069787e1783 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
@@ -16,6 +16,65 @@
 		stdout-path = "serial2:115200n8";
 		bootargs = "console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000";
 	};
+
+	evm_12v0: fixedregulator-evm12v0 {
+		/* main supply */
+		compatible = "regulator-fixed";
+		regulator-name = "evm_12v0";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vsys_3v3: fixedregulator-vsys3v3 {
+		/* Output of LMS140 */
+		compatible = "regulator-fixed";
+		regulator-name = "vsys_3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&evm_12v0>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vsys_5v0: fixedregulator-vsys5v0 {
+		/* Output of LM5140 */
+		compatible = "regulator-fixed";
+		regulator-name = "vsys_5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&evm_12v0>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vdd_mmc1: fixedregulator-sd {
+		/* Output of TPS22918  */
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_mmc1";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		enable-active-high;
+		vin-supply = <&vsys_3v3>;
+		gpio = <&exp2 2 GPIO_ACTIVE_HIGH>;
+	};
+
+	vdd_sd_dv: gpio-regulator-vdd-sd-dv {
+		/* Output of TLV71033 */
+		compatible = "regulator-gpio";
+		regulator-name = "vdd_sd_dv";
+		pinctrl-names = "default";
+		pinctrl-0 = <&vdd_sd_dv_pins_default>;
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		vin-supply = <&vsys_5v0>;
+		gpios = <&main_gpio0 55 GPIO_ACTIVE_HIGH>;
+		states = <1800000 0x0>,
+			 <3300000 0x1>;
+	};
 };
 
 &wkup_pmx0 {
@@ -45,6 +104,13 @@
 };
 
 &main_pmx0 {
+	main_i2c0_pins_default: main-i2c0-pins-default {
+		pinctrl-single,pins = <
+			J721E_IOPAD(0xd4, PIN_INPUT_PULLUP, 0) /* (V3) I2C0_SCL */
+			J721E_IOPAD(0xd8, PIN_INPUT_PULLUP, 0) /* (W2) I2C0_SDA */
+		>;
+	};
+
 	main_i2c1_pins_default: main-i2c1-pins-default {
 		pinctrl-single,pins = <
 			J721E_IOPAD(0xdc, PIN_INPUT_PULLUP, 3) /* (U3) ECAP0_IN_APWM_OUT.I2C1_SCL */
@@ -70,6 +136,12 @@
 			J721E_IOPAD(0x120, PIN_OUTPUT, 0) /* (T4) USB0_DRVVBUS */
 		>;
 	};
+
+	vdd_sd_dv_pins_default: vdd-sd-dv-pins-default {
+		pinctrl-single,pins = <
+			J721E_IOPAD(0xd0, PIN_INPUT, 7) /* (T5) SPI0_D1.GPIO0_55 */
+		>;
+	};
 };
 
 &wkup_uart0 {
@@ -157,6 +229,10 @@
 };
 
 &main_i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_i2c0_pins_default>;
+	clock-frequency = <400000>;
+
 	exp1: gpio@20 {
 		compatible = "ti,tca6416";
 		reg = <0x20>;
@@ -206,6 +282,8 @@
 	/* SD card */
 	pinctrl-0 = <&main_mmc1_pins_default>;
 	pinctrl-names = "default";
+	vmmc-supply = <&vdd_mmc1>;
+	vqmmc-supply = <&vdd_sd_dv>;
 	ti,driver-strength-ohm = <50>;
 	disable-wp;
 };
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
index e60650a62b14..f86c493a44f1 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
@@ -512,11 +512,16 @@
 		ti,otap-del-sel-mmc-hs = <0x0>;
 		ti,otap-del-sel-ddr52 = <0x6>;
 		ti,otap-del-sel-hs200 = <0x8>;
-		ti,otap-del-sel-hs400 = <0x0>;
+		ti,otap-del-sel-hs400 = <0x5>;
+		ti,itap-del-sel-legacy = <0x10>;
+		ti,itap-del-sel-mmc-hs = <0xa>;
 		ti,strobe-sel = <0x77>;
+		ti,clkbuf-sel = <0x7>;
 		ti,trm-icp = <0x8>;
 		bus-width = <8>;
 		mmc-ddr-1_8v;
+		mmc-hs200-1_8v;
+		mmc-hs400-1_8v;
 		dma-coherent;
 	};
 
@@ -534,7 +539,12 @@
 		ti,otap-del-sel-sdr50 = <0xc>;
 		ti,otap-del-sel-sdr104 = <0x5>;
 		ti,otap-del-sel-ddr50 = <0xc>;
-		no-1-8-v;
+		ti,itap-del-sel-legacy = <0x0>;
+		ti,itap-del-sel-sd-hs = <0x0>;
+		ti,itap-del-sel-sdr12 = <0x0>;
+		ti,itap-del-sel-sdr25 = <0x0>;
+		ti,clkbuf-sel = <0x7>;
+		ti,trm-icp = <0x8>;
 		dma-coherent;
 	};
 
-- 
2.17.1

Re: [PATCH v8 3/3] arm64: dts: ti: k3-j7200: Add support for higher speed modes and update delay select values for MMCSD subsystems

[Kishon Vijay Abraham I]

Hi Aswath,

On 24/03/21 12:07 pm, Aswath Govindraju wrote:
> The following speed modes are now supported in J7200 SoC,
> - HS200 and HS400 modes at 1.8 V card voltage, in MMCSD0 subsystem [1].
> - UHS-I speed modes in MMCSD1 subsystem [1].
> 
> Add support for UHS-I modes by adding voltage regulator device tree nodes
> and corresponding pinmux details, to power cycle and voltage switch cards.
> Set respective tags in sdhci0 and remove no-1-8-v tag from sdhci1
> device tree nodes.
> 
> Also update the delay values for various speed modes supported, based on
> the revised january 2021 J7200 datasheet[2].
> 
> [1] - section 12.3.6.1.1 MMCSD Features, in
>       https://www.ti.com/lit/ug/spruiu1a/spruiu1a.pdf,
>       (SPRUIU1A – JULY 2020 – REVISED JANUARY 2021)
> 
> [2] - https://www.ti.com/lit/ds/symlink/dra821u.pdf,
>       (SPRSP57B – APRIL 2020 – REVISED JANUARY 2021)
minor comments below.. once you fix them, please add

Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com>
> 
> Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
> ---
>  .../dts/ti/k3-j7200-common-proc-board.dts     | 78 +++++++++++++++++++
>  arch/arm64/boot/dts/ti/k3-j7200-main.dtsi     | 14 +++-
>  2 files changed, 90 insertions(+), 2 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
> index b493f939b09a..a069787e1783 100644
> --- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
> +++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
> @@ -16,6 +16,65 @@
>  		stdout-path = "serial2:115200n8";
>  		bootargs = "console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000";
>  	};
> +
> +	evm_12v0: fixedregulator-evm12v0 {
> +		/* main supply */
> +		compatible = "regulator-fixed";
> +		regulator-name = "evm_12v0";
> +		regulator-min-microvolt = <12000000>;
> +		regulator-max-microvolt = <12000000>;
> +		regulator-always-on;
> +		regulator-boot-on;
> +	};
> +
> +	vsys_3v3: fixedregulator-vsys3v3 {
> +		/* Output of LMS140 */

%s/LMS140/LM5140
> +		compatible = "regulator-fixed";
> +		regulator-name = "vsys_3v3";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		vin-supply = <&evm_12v0>;
> +		regulator-always-on;
> +		regulator-boot-on;
> +	};
> +
> +	vsys_5v0: fixedregulator-vsys5v0 {
> +		/* Output of LM5140 */
> +		compatible = "regulator-fixed";
> +		regulator-name = "vsys_5v0";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		vin-supply = <&evm_12v0>;
> +		regulator-always-on;
> +		regulator-boot-on;
> +	};
> +
> +	vdd_mmc1: fixedregulator-sd {
> +		/* Output of TPS22918  */
> +		compatible = "regulator-fixed";
> +		regulator-name = "vdd_mmc1";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		regulator-boot-on;
> +		enable-active-high;
> +		vin-supply = <&vsys_3v3>;
> +		gpio = <&exp2 2 GPIO_ACTIVE_HIGH>;
> +	};
> +
> +	vdd_sd_dv: gpio-regulator-vdd-sd-dv {
> +		/* Output of TLV71033 */

Would have preferred to keep this similar to j721e.
gpio-regulator-TLV71033 is used in j721e
> +		compatible = "regulator-gpio";
> +		regulator-name = "vdd_sd_dv";

same comment here..
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&vdd_sd_dv_pins_default>;
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <3300000>;
> +		regulator-boot-on;
> +		vin-supply = <&vsys_5v0>;
> +		gpios = <&main_gpio0 55 GPIO_ACTIVE_HIGH>;
> +		states = <1800000 0x0>,
> +			 <3300000 0x1>;
> +	};
>  };
>  
>  &wkup_pmx0 {
> @@ -45,6 +104,13 @@
>  };
>  
>  &main_pmx0 {
> +	main_i2c0_pins_default: main-i2c0-pins-default {
> +		pinctrl-single,pins = <
> +			J721E_IOPAD(0xd4, PIN_INPUT_PULLUP, 0) /* (V3) I2C0_SCL */
> +			J721E_IOPAD(0xd8, PIN_INPUT_PULLUP, 0) /* (W2) I2C0_SDA */
> +		>;
> +	};
> +
>  	main_i2c1_pins_default: main-i2c1-pins-default {
>  		pinctrl-single,pins = <
>  			J721E_IOPAD(0xdc, PIN_INPUT_PULLUP, 3) /* (U3) ECAP0_IN_APWM_OUT.I2C1_SCL */
> @@ -70,6 +136,12 @@
>  			J721E_IOPAD(0x120, PIN_OUTPUT, 0) /* (T4) USB0_DRVVBUS */
>  		>;
>  	};
> +
> +	vdd_sd_dv_pins_default: vdd-sd-dv-pins-default {
> +		pinctrl-single,pins = <
> +			J721E_IOPAD(0xd0, PIN_INPUT, 7) /* (T5) SPI0_D1.GPIO0_55 */

This should ideally be PIN_OUTPUT. Can you check the latest sysconfig?

Thanks
Kishon

Re: [PATCH v8 3/3] arm64: dts: ti: k3-j7200: Add support for higher speed modes and update delay select values for MMCSD subsystems

[Aswath Govindraju]

Hi Kishon,

On 25/03/21 9:44 pm, Kishon Vijay Abraham I wrote:
> Hi Aswath,
> 
> On 24/03/21 12:07 pm, Aswath Govindraju wrote:
>> The following speed modes are now supported in J7200 SoC,
>> - HS200 and HS400 modes at 1.8 V card voltage, in MMCSD0 subsystem [1].
>> - UHS-I speed modes in MMCSD1 subsystem [1].
>>
>> Add support for UHS-I modes by adding voltage regulator device tree nodes
>> and corresponding pinmux details, to power cycle and voltage switch cards.
>> Set respective tags in sdhci0 and remove no-1-8-v tag from sdhci1
>> device tree nodes.
>>
>> Also update the delay values for various speed modes supported, based on
>> the revised january 2021 J7200 datasheet[2].
>>
>> [1] - section 12.3.6.1.1 MMCSD Features, in
>>       https://www.ti.com/lit/ug/spruiu1a/spruiu1a.pdf,
>>       (SPRUIU1A – JULY 2020 – REVISED JANUARY 2021)
>>
>> [2] - https://www.ti.com/lit/ds/symlink/dra821u.pdf,
>>       (SPRSP57B – APRIL 2020 – REVISED JANUARY 2021)
> minor comments below.. once you fix them, please add
> 
> Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com>
>>

Thank you for your review :).

>> Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
>> ---
>>  .../dts/ti/k3-j7200-common-proc-board.dts     | 78 +++++++++++++++++++
>>  arch/arm64/boot/dts/ti/k3-j7200-main.dtsi     | 14 +++-
>>  2 files changed, 90 insertions(+), 2 deletions(-)
>>
>> diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
>> index b493f939b09a..a069787e1783 100644
>> --- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
>> +++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
>> @@ -16,6 +16,65 @@
>>  		stdout-path = "serial2:115200n8";
>>  		bootargs = "console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000";
>>  	};
>> +
>> +	evm_12v0: fixedregulator-evm12v0 {
>> +		/* main supply */
>> +		compatible = "regulator-fixed";
>> +		regulator-name = "evm_12v0";
>> +		regulator-min-microvolt = <12000000>;
>> +		regulator-max-microvolt = <12000000>;
>> +		regulator-always-on;
>> +		regulator-boot-on;
>> +	};
>> +
>> +	vsys_3v3: fixedregulator-vsys3v3 {
>> +		/* Output of LMS140 */
> 
> %s/LMS140/LM5140

Will make this change in respin.

>> +		compatible = "regulator-fixed";
>> +		regulator-name = "vsys_3v3";
>> +		regulator-min-microvolt = <3300000>;
>> +		regulator-max-microvolt = <3300000>;
>> +		vin-supply = <&evm_12v0>;
>> +		regulator-always-on;
>> +		regulator-boot-on;
>> +	};
>> +
>> +	vsys_5v0: fixedregulator-vsys5v0 {
>> +		/* Output of LM5140 */
>> +		compatible = "regulator-fixed";
>> +		regulator-name = "vsys_5v0";
>> +		regulator-min-microvolt = <5000000>;
>> +		regulator-max-microvolt = <5000000>;
>> +		vin-supply = <&evm_12v0>;
>> +		regulator-always-on;
>> +		regulator-boot-on;
>> +	};
>> +
>> +	vdd_mmc1: fixedregulator-sd {
>> +		/* Output of TPS22918  */
>> +		compatible = "regulator-fixed";
>> +		regulator-name = "vdd_mmc1";
>> +		regulator-min-microvolt = <3300000>;
>> +		regulator-max-microvolt = <3300000>;
>> +		regulator-boot-on;
>> +		enable-active-high;
>> +		vin-supply = <&vsys_3v3>;
>> +		gpio = <&exp2 2 GPIO_ACTIVE_HIGH>;
>> +	};
>> +
>> +	vdd_sd_dv: gpio-regulator-vdd-sd-dv {
>> +		/* Output of TLV71033 */
> 
> Would have preferred to keep this similar to j721e.
> gpio-regulator-TLV71033 is used in j721e

Will make this change in respin

>> +		compatible = "regulator-gpio";
>> +		regulator-name = "vdd_sd_dv";
> 
> same comment here..

Will make this change in respin

>> +		pinctrl-names = "default";
>> +		pinctrl-0 = <&vdd_sd_dv_pins_default>;
>> +		regulator-min-microvolt = <1800000>;
>> +		regulator-max-microvolt = <3300000>;
>> +		regulator-boot-on;
>> +		vin-supply = <&vsys_5v0>;
>> +		gpios = <&main_gpio0 55 GPIO_ACTIVE_HIGH>;
>> +		states = <1800000 0x0>,
>> +			 <3300000 0x1>;
>> +	};
>>  };
>>  
>>  &wkup_pmx0 {
>> @@ -45,6 +104,13 @@
>>  };
>>  
>>  &main_pmx0 {
>> +	main_i2c0_pins_default: main-i2c0-pins-default {
>> +		pinctrl-single,pins = <
>> +			J721E_IOPAD(0xd4, PIN_INPUT_PULLUP, 0) /* (V3) I2C0_SCL */
>> +			J721E_IOPAD(0xd8, PIN_INPUT_PULLUP, 0) /* (W2) I2C0_SDA */
>> +		>;
>> +	};
>> +
>>  	main_i2c1_pins_default: main-i2c1-pins-default {
>>  		pinctrl-single,pins = <
>>  			J721E_IOPAD(0xdc, PIN_INPUT_PULLUP, 3) /* (U3) ECAP0_IN_APWM_OUT.I2C1_SCL */
>> @@ -70,6 +136,12 @@
>>  			J721E_IOPAD(0x120, PIN_OUTPUT, 0) /* (T4) USB0_DRVVBUS */
>>  		>;
>>  	};
>> +
>> +	vdd_sd_dv_pins_default: vdd-sd-dv-pins-default {
>> +		pinctrl-single,pins = <
>> +			J721E_IOPAD(0xd0, PIN_INPUT, 7) /* (T5) SPI0_D1.GPIO0_55 */
> 
> This should ideally be PIN_OUTPUT. Can you check the latest sysconfig?
> 

The sysconfig tool by default is giving the mode as
PIN_INPUT(bidirectional) but yes ideally this should be PIN_OUTPUT. Will
make this change in respin.

Thanks,
Aswath

> Thanks
> Kishon
>