* [PATCH v3] dt-bindings: gpio: stp: convert to json-schema
@ 2021-05-23 17:39 Aleksander Jan Bajkowski
2021-05-27 14:59 ` Linus Walleij
2021-06-02 18:56 ` Rob Herring
0 siblings, 2 replies; 3+ messages in thread
From: Aleksander Jan Bajkowski @ 2021-05-23 17:39 UTC (permalink / raw)
To: linus.walleij, bgolaszewski, robh+dt, john, linux-gpio,
devicetree, linux-kernel
Cc: Aleksander Jan Bajkowski
Convert the Lantiq STP Device Tree binding documentation to json-schema.
Add the missing pinctrl property to the example. Add missing lantiq,phy3
and lantiq,phy4 bindings for xRX300 and xRX330 SoCs.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
---
Changes since v2:
- Changed phy numbering in description of pattern Properties. Numbering
should start with 1.
Changes since v1:
- Renamed node to gpio.
- Dropped default pinctrl from this binding.
- Converted lantiq,phyX to patternProperties.
---
.../bindings/gpio/gpio-stp-xway.txt | 42 --------
.../bindings/gpio/gpio-stp-xway.yaml | 101 ++++++++++++++++++
2 files changed, 101 insertions(+), 42 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/gpio/gpio-stp-xway.txt
create mode 100644 Documentation/devicetree/bindings/gpio/gpio-stp-xway.yaml
diff --git a/Documentation/devicetree/bindings/gpio/gpio-stp-xway.txt b/Documentation/devicetree/bindings/gpio/gpio-stp-xway.txt
deleted file mode 100644
index 78458adbf4b7..000000000000
--- a/Documentation/devicetree/bindings/gpio/gpio-stp-xway.txt
+++ /dev/null
@@ -1,42 +0,0 @@
-Lantiq SoC Serial To Parallel (STP) GPIO controller
-
-The Serial To Parallel (STP) is found on MIPS based Lantiq socs. It is a
-peripheral controller used to drive external shift register cascades. At most
-3 groups of 8 bits can be driven. The hardware is able to allow the DSL modem
-to drive the 2 LSBs of the cascade automatically.
-
-
-Required properties:
-- compatible : Should be "lantiq,gpio-stp-xway"
-- reg : Address and length of the register set for the device
-- #gpio-cells : Should be two. The first cell is the pin number and
- the second cell is used to specify optional parameters (currently
- unused).
-- gpio-controller : Marks the device node as a gpio controller.
-
-Optional properties:
-- lantiq,shadow : The default value that we shall assume as already set on the
- shift register cascade.
-- lantiq,groups : Set the 3 bit mask to select which of the 3 groups are enabled
- in the shift register cascade.
-- lantiq,dsl : The dsl core can control the 2 LSBs of the gpio cascade. This 2 bit
- property can enable this feature.
-- lantiq,phy1 : The gphy1 core can control 3 bits of the gpio cascade.
-- lantiq,phy2 : The gphy2 core can control 3 bits of the gpio cascade.
-- lantiq,rising : use rising instead of falling edge for the shift register
-
-Example:
-
-gpio1: stp@e100bb0 {
- compatible = "lantiq,gpio-stp-xway";
- reg = <0xE100BB0 0x40>;
- #gpio-cells = <2>;
- gpio-controller;
-
- lantiq,shadow = <0xffff>;
- lantiq,groups = <0x7>;
- lantiq,dsl = <0x3>;
- lantiq,phy1 = <0x7>;
- lantiq,phy2 = <0x7>;
- /* lantiq,rising; */
-};
diff --git a/Documentation/devicetree/bindings/gpio/gpio-stp-xway.yaml b/Documentation/devicetree/bindings/gpio/gpio-stp-xway.yaml
new file mode 100644
index 000000000000..7d817d84c434
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/gpio-stp-xway.yaml
@@ -0,0 +1,101 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/gpio/gpio-stp-xway.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Lantiq SoC Serial To Parallel (STP) GPIO controller
+
+description: |
+ The Serial To Parallel (STP) is found on MIPS based Lantiq socs. It is a
+ peripheral controller used to drive external shift register cascades. At most
+ 3 groups of 8 bits can be driven. The hardware is able to allow the DSL modem
+ and Ethernet PHYs to drive some bytes of the cascade automatically.
+
+maintainers:
+ - John Crispin <john@phrozen.org>
+
+properties:
+ $nodename:
+ pattern: "^gpio@[0-9a-f]+$"
+
+ compatible:
+ const: lantiq,gpio-stp-xway
+
+ reg:
+ description:
+ Address and length of the register set for the device.
+ maxItems: 1
+
+ gpio-controller: true
+
+ "#gpio-cells":
+ description:
+ The first cell is the pin number and the second cell is used to specify
+ consumer flags.
+ const: 2
+
+ lantiq,shadow:
+ description:
+ The default value that we shall assume as already set on the
+ shift register cascade.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0x000000
+ maximum: 0xffffff
+
+ lantiq,groups:
+ description:
+ Set the 3 bit mask to select which of the 3 groups are enabled
+ in the shift register cascade.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0x0
+ maximum: 0x7
+
+ lantiq,dsl:
+ description:
+ The dsl core can control the 2 LSBs of the gpio cascade. This 2 bit
+ property can enable this feature.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0x0
+ maximum: 0x3
+
+patternProperties:
+ "lantiq,phy[1-4]":
+ description:
+ The gphy core can control 3 bits of the gpio cascade. In the xRX200 family
+ phy[1-2] are available, in xRX330 phy[1-3] and in XRX330 phy[1-4].
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0x0
+ maximum: 0x7
+
+ lantiq,rising:
+ description:
+ Use rising instead of falling edge for the shift register.
+ type: boolean
+
+required:
+ - compatible
+ - reg
+ - gpio-controller
+ - "#gpio-cells"
+
+additionalProperties: false
+
+examples:
+ - |
+ gpio@e100bb0 {
+ compatible = "lantiq,gpio-stp-xway";
+ reg = <0xE100BB0 0x40>;
+ #gpio-cells = <2>;
+ gpio-controller;
+
+ pinctrl-0 = <&stp_pins>;
+ pinctrl-names = "default";
+
+ lantiq,shadow = <0xffffff>;
+ lantiq,groups = <0x7>;
+ lantiq,dsl = <0x3>;
+ lantiq,phy1 = <0x7>;
+ lantiq,phy2 = <0x7>;
+ };
+...
--
2.30.2
^ permalink raw reply related [flat|nested] 3+ messages in thread
* Re: [PATCH v3] dt-bindings: gpio: stp: convert to json-schema
2021-05-23 17:39 [PATCH v3] dt-bindings: gpio: stp: convert to json-schema Aleksander Jan Bajkowski
@ 2021-05-27 14:59 ` Linus Walleij
2021-06-02 18:56 ` Rob Herring
1 sibling, 0 replies; 3+ messages in thread
From: Linus Walleij @ 2021-05-27 14:59 UTC (permalink / raw)
To: Aleksander Jan Bajkowski
Cc: Bartosz Golaszewski, Rob Herring, John Crispin,
open list:GPIO SUBSYSTEM,
open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
linux-kernel
On Sun, May 23, 2021 at 7:39 PM Aleksander Jan Bajkowski <olek2@wp.pl> wrote:
> Convert the Lantiq STP Device Tree binding documentation to json-schema.
> Add the missing pinctrl property to the example. Add missing lantiq,phy3
> and lantiq,phy4 bindings for xRX300 and xRX330 SoCs.
>
> Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Yours,
Linus Walleij
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: [PATCH v3] dt-bindings: gpio: stp: convert to json-schema
2021-05-23 17:39 [PATCH v3] dt-bindings: gpio: stp: convert to json-schema Aleksander Jan Bajkowski
2021-05-27 14:59 ` Linus Walleij
@ 2021-06-02 18:56 ` Rob Herring
1 sibling, 0 replies; 3+ messages in thread
From: Rob Herring @ 2021-06-02 18:56 UTC (permalink / raw)
To: Aleksander Jan Bajkowski
Cc: linus.walleij, bgolaszewski, john, linux-gpio, devicetree, linux-kernel
On Sun, May 23, 2021 at 07:39:10PM +0200, Aleksander Jan Bajkowski wrote:
> Convert the Lantiq STP Device Tree binding documentation to json-schema.
> Add the missing pinctrl property to the example. Add missing lantiq,phy3
> and lantiq,phy4 bindings for xRX300 and xRX330 SoCs.
>
> Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
> ---
> Changes since v2:
> - Changed phy numbering in description of pattern Properties. Numbering
> should start with 1.
> Changes since v1:
> - Renamed node to gpio.
> - Dropped default pinctrl from this binding.
> - Converted lantiq,phyX to patternProperties.
> ---
> .../bindings/gpio/gpio-stp-xway.txt | 42 --------
> .../bindings/gpio/gpio-stp-xway.yaml | 101 ++++++++++++++++++
> 2 files changed, 101 insertions(+), 42 deletions(-)
> delete mode 100644 Documentation/devicetree/bindings/gpio/gpio-stp-xway.txt
> create mode 100644 Documentation/devicetree/bindings/gpio/gpio-stp-xway.yaml
>
> diff --git a/Documentation/devicetree/bindings/gpio/gpio-stp-xway.txt b/Documentation/devicetree/bindings/gpio/gpio-stp-xway.txt
> deleted file mode 100644
> index 78458adbf4b7..000000000000
> --- a/Documentation/devicetree/bindings/gpio/gpio-stp-xway.txt
> +++ /dev/null
> @@ -1,42 +0,0 @@
> -Lantiq SoC Serial To Parallel (STP) GPIO controller
> -
> -The Serial To Parallel (STP) is found on MIPS based Lantiq socs. It is a
> -peripheral controller used to drive external shift register cascades. At most
> -3 groups of 8 bits can be driven. The hardware is able to allow the DSL modem
> -to drive the 2 LSBs of the cascade automatically.
> -
> -
> -Required properties:
> -- compatible : Should be "lantiq,gpio-stp-xway"
> -- reg : Address and length of the register set for the device
> -- #gpio-cells : Should be two. The first cell is the pin number and
> - the second cell is used to specify optional parameters (currently
> - unused).
> -- gpio-controller : Marks the device node as a gpio controller.
> -
> -Optional properties:
> -- lantiq,shadow : The default value that we shall assume as already set on the
> - shift register cascade.
> -- lantiq,groups : Set the 3 bit mask to select which of the 3 groups are enabled
> - in the shift register cascade.
> -- lantiq,dsl : The dsl core can control the 2 LSBs of the gpio cascade. This 2 bit
> - property can enable this feature.
> -- lantiq,phy1 : The gphy1 core can control 3 bits of the gpio cascade.
> -- lantiq,phy2 : The gphy2 core can control 3 bits of the gpio cascade.
> -- lantiq,rising : use rising instead of falling edge for the shift register
> -
> -Example:
> -
> -gpio1: stp@e100bb0 {
> - compatible = "lantiq,gpio-stp-xway";
> - reg = <0xE100BB0 0x40>;
> - #gpio-cells = <2>;
> - gpio-controller;
> -
> - lantiq,shadow = <0xffff>;
> - lantiq,groups = <0x7>;
> - lantiq,dsl = <0x3>;
> - lantiq,phy1 = <0x7>;
> - lantiq,phy2 = <0x7>;
> - /* lantiq,rising; */
> -};
> diff --git a/Documentation/devicetree/bindings/gpio/gpio-stp-xway.yaml b/Documentation/devicetree/bindings/gpio/gpio-stp-xway.yaml
> new file mode 100644
> index 000000000000..7d817d84c434
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/gpio/gpio-stp-xway.yaml
> @@ -0,0 +1,101 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/gpio/gpio-stp-xway.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Lantiq SoC Serial To Parallel (STP) GPIO controller
> +
> +description: |
> + The Serial To Parallel (STP) is found on MIPS based Lantiq socs. It is a
> + peripheral controller used to drive external shift register cascades. At most
> + 3 groups of 8 bits can be driven. The hardware is able to allow the DSL modem
> + and Ethernet PHYs to drive some bytes of the cascade automatically.
> +
> +maintainers:
> + - John Crispin <john@phrozen.org>
> +
> +properties:
> + $nodename:
> + pattern: "^gpio@[0-9a-f]+$"
> +
> + compatible:
> + const: lantiq,gpio-stp-xway
> +
> + reg:
> + description:
> + Address and length of the register set for the device.
Drop. Don't need generic descriptions.
> + maxItems: 1
> +
> + gpio-controller: true
> +
> + "#gpio-cells":
> + description:
> + The first cell is the pin number and the second cell is used to specify
> + consumer flags.
> + const: 2
> +
> + lantiq,shadow:
> + description:
> + The default value that we shall assume as already set on the
> + shift register cascade.
> + $ref: /schemas/types.yaml#/definitions/uint32
> + minimum: 0x000000
> + maximum: 0xffffff
> +
> + lantiq,groups:
> + description:
> + Set the 3 bit mask to select which of the 3 groups are enabled
> + in the shift register cascade.
> + $ref: /schemas/types.yaml#/definitions/uint32
> + minimum: 0x0
> + maximum: 0x7
> +
> + lantiq,dsl:
> + description:
> + The dsl core can control the 2 LSBs of the gpio cascade. This 2 bit
> + property can enable this feature.
> + $ref: /schemas/types.yaml#/definitions/uint32
> + minimum: 0x0
> + maximum: 0x3
> +
> +patternProperties:
> + "lantiq,phy[1-4]":
"^lantiq,phy[1-4]$"
> + description:
> + The gphy core can control 3 bits of the gpio cascade. In the xRX200 family
> + phy[1-2] are available, in xRX330 phy[1-3] and in XRX330 phy[1-4].
> + $ref: /schemas/types.yaml#/definitions/uint32
> + minimum: 0x0
> + maximum: 0x7
> +
> + lantiq,rising:
Not a pattern. Move to 'properties'.
> + description:
> + Use rising instead of falling edge for the shift register.
> + type: boolean
> +
> +required:
> + - compatible
> + - reg
> + - gpio-controller
> + - "#gpio-cells"
> +
> +additionalProperties: false
> +
> +examples:
> + - |
> + gpio@e100bb0 {
> + compatible = "lantiq,gpio-stp-xway";
> + reg = <0xE100BB0 0x40>;
> + #gpio-cells = <2>;
> + gpio-controller;
> +
> + pinctrl-0 = <&stp_pins>;
> + pinctrl-names = "default";
> +
> + lantiq,shadow = <0xffffff>;
> + lantiq,groups = <0x7>;
> + lantiq,dsl = <0x3>;
> + lantiq,phy1 = <0x7>;
> + lantiq,phy2 = <0x7>;
> + };
> +...
> --
> 2.30.2
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2021-06-02 18:56 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2021-05-23 17:39 [PATCH v3] dt-bindings: gpio: stp: convert to json-schema Aleksander Jan Bajkowski
2021-05-27 14:59 ` Linus Walleij
2021-06-02 18:56 ` Rob Herring
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).