Re: [PATCH v3 11/11] media: dt-bindings: Convert Cadence CSI2RX binding to YAML

[Pratyush Yadav <p.yadav@ti.com>]

On 01/07/21 12:55PM, Rob Herring wrote:
> On Fri, Jun 25, 2021 at 12:52:00AM +0530, Pratyush Yadav wrote:
> > Convert the Cadence CSI2RX binding to use YAML schema.
> > 
> > Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
> > 
> > ---
> > 
> > Changes in v3:
> > - Add compatible: contains: const: cdns,csi2rx to allow SoC specific
> >   compatible.
> > - Add more constraints for data-lanes property.
> > 
> > Changes in v2:
> > - New in v2.
> > 
> >  .../devicetree/bindings/media/cdns,csi2rx.txt | 100 -----------
> >  .../bindings/media/cdns,csi2rx.yaml           | 169 ++++++++++++++++++
> >  2 files changed, 169 insertions(+), 100 deletions(-)
> >  delete mode 100644 Documentation/devicetree/bindings/media/cdns,csi2rx.txt
> >  create mode 100644 Documentation/devicetree/bindings/media/cdns,csi2rx.yaml
> > 
> > diff --git a/Documentation/devicetree/bindings/media/cdns,csi2rx.txt b/Documentation/devicetree/bindings/media/cdns,csi2rx.txt
> > deleted file mode 100644
> > index 6b02a0657ad9..000000000000
> > --- a/Documentation/devicetree/bindings/media/cdns,csi2rx.txt
> > +++ /dev/null
> > @@ -1,100 +0,0 @@
> > -Cadence MIPI-CSI2 RX controller
> > -===============================
> > -
> > -The Cadence MIPI-CSI2 RX controller is a CSI-2 bridge supporting up to 4 CSI
> > -lanes in input, and 4 different pixel streams in output.
> > -
> > -Required properties:
> > -  - compatible: must be set to "cdns,csi2rx" and an SoC-specific compatible
> > -  - reg: base address and size of the memory mapped region
> > -  - clocks: phandles to the clocks driving the controller
> > -  - clock-names: must contain:
> > -    * sys_clk: main clock
> > -    * p_clk: register bank clock
> > -    * pixel_if[0-3]_clk: pixel stream output clock, one for each stream
> > -                         implemented in hardware, between 0 and 3
> > -
> > -Optional properties:
> > -  - phys: phandle to the external D-PHY, phy-names must be provided
> > -  - phy-names: must contain "dphy", if the implementation uses an
> > -               external D-PHY
> > -
> > -Required subnodes:
> > -  - ports: A ports node with one port child node per device input and output
> > -           port, in accordance with the video interface bindings defined in
> > -           Documentation/devicetree/bindings/media/video-interfaces.txt. The
> > -           port nodes are numbered as follows:
> > -
> > -           Port Description
> > -           -----------------------------
> > -           0    CSI-2 input
> > -           1    Stream 0 output
> > -           2    Stream 1 output
> > -           3    Stream 2 output
> > -           4    Stream 3 output
> > -
> > -           The stream output port nodes are optional if they are not
> > -           connected to anything at the hardware level or implemented
> > -           in the design.Since there is only one endpoint per port,
> > -           the endpoints are not numbered.
> > -
> > -
> > -Example:
> > -
> > -csi2rx: csi-bridge@0d060000 {
> > -	compatible = "cdns,csi2rx";
> > -	reg = <0x0d060000 0x1000>;
> > -	clocks = <&byteclock>, <&byteclock>
> > -		 <&coreclock>, <&coreclock>,
> > -		 <&coreclock>, <&coreclock>;
> > -	clock-names = "sys_clk", "p_clk",
> > -		      "pixel_if0_clk", "pixel_if1_clk",
> > -		      "pixel_if2_clk", "pixel_if3_clk";
> > -
> > -	ports {
> > -		#address-cells = <1>;
> > -		#size-cells = <0>;
> > -
> > -		port@0 {
> > -			reg = <0>;
> > -
> > -			csi2rx_in_sensor: endpoint {
> > -				remote-endpoint = <&sensor_out_csi2rx>;
> > -				clock-lanes = <0>;
> > -				data-lanes = <1 2>;
> > -			};
> > -		};
> > -
> > -		port@1 {
> > -			reg = <1>;
> > -
> > -			csi2rx_out_grabber0: endpoint {
> > -				remote-endpoint = <&grabber0_in_csi2rx>;
> > -			};
> > -		};
> > -
> > -		port@2 {
> > -			reg = <2>;
> > -
> > -			csi2rx_out_grabber1: endpoint {
> > -				remote-endpoint = <&grabber1_in_csi2rx>;
> > -			};
> > -		};
> > -
> > -		port@3 {
> > -			reg = <3>;
> > -
> > -			csi2rx_out_grabber2: endpoint {
> > -				remote-endpoint = <&grabber2_in_csi2rx>;
> > -			};
> > -		};
> > -
> > -		port@4 {
> > -			reg = <4>;
> > -
> > -			csi2rx_out_grabber3: endpoint {
> > -				remote-endpoint = <&grabber3_in_csi2rx>;
> > -			};
> > -		};
> > -	};
> > -};
> > diff --git a/Documentation/devicetree/bindings/media/cdns,csi2rx.yaml b/Documentation/devicetree/bindings/media/cdns,csi2rx.yaml
> > new file mode 100644
> > index 000000000000..8e42c9fdaaa3
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/media/cdns,csi2rx.yaml
> > @@ -0,0 +1,169 @@
> > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> > +%YAML 1.2
> > +---
> > +$id: http://devicetree.org/schemas/media/cdns,csi2rx.yaml#
> > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > +
> > +title: Cadence MIPI-CSI2 RX controller
> > +
> > +description: |
> > +  The Cadence MIPI-CSI2 RX controller is a CSI-2 bridge supporting up to 4 CSI
> > +  lanes in input, and 4 different pixel streams in output.
> > +
> > +maintainers:
> > +  - Pratyush Yadav <p.yadav@ti.com>
> > +
> > +properties:
> > +  compatible:
> > +    contains:
> > +      const: cdns,csi2rx
> > +
> > +  reg:
> > +    maxItems: 1
> > +
> > +  clocks:
> > +    minItems: 3
> > +    maxItems: 6
> > +
> > +  clock-names:
> > +    minItems: 3
> > +    maxItems: 6
> 
> maxItems can be dropped here. Implied by items length.

Ok.

> 
> > +    items:
> > +      - const: sys_clk # main clock
> > +      - const: p_clk # register bank clock
> > +      - const: pixel_if0_clk # pixel stream 0 output clock
> > +      - const: pixel_if1_clk # pixel stream 1 output clock
> > +      - const: pixel_if2_clk # pixel stream 2 output clock
> > +      - const: pixel_if3_clk # pixel stream 3 output clock
> > +
> > +  phys:
> > +    maxItems: 1
> > +    description: phandle to the external D-PHY
> > +
> > +  phy-names:
> > +    items:
> > +      - const: dphy
> > +
> > +  ports:
> > +    $ref: /schemas/graph.yaml#/properties/ports
> > +
> > +    properties:
> > +      port@0:
> > +        $ref: /schemas/graph.yaml#/$defs/port-base
> > +        unevaluatedProperties: false
> > +        description: CSI-2 input
> > +
> > +        properties:
> > +          endpoint:
> > +            $ref: video-interfaces.yaml#
> > +            unevaluatedProperties: false
> > +
> > +            properties:
> > +              clock-lanes:
> > +                maxItems: 1
> > +
> > +              data-lanes:
> > +                $ref: /schemas/types.yaml#/definitions/uint32-array
> 
> Don't need a type here.

Ok.

> 
> > +                minItems: 1
> > +                maxItems: 4
> > +                uniqueItems: true
> 
> uniqueItems should be added in video-interfaces.yaml.

Ok. I will send that change as a separate patch independent of this 
series.

Thanks for reviewing.

> 
> > +                items:
> > +                  maximum: 4
> > +
> > +            required:
> > +              - clock-lanes
> > +              - data-lanes
> > +
[...]

-- 
Regards,
Pratyush Yadav
Texas Instruments Inc.