* [PATCH 0/2] Add UART driver for Suplus SP7021 SoC
@ 2021-11-01 7:48 hammer.hsieh
2021-11-01 7:48 ` [PATCH 1/2] dt-bindings:serial:Add bindings doc for Sunplus SoC UART Driver hammer.hsieh
` (3 more replies)
0 siblings, 4 replies; 19+ messages in thread
From: hammer.hsieh @ 2021-11-01 7:48 UTC (permalink / raw)
To: gregkh, linux-serial, devicetree, linux-kernel, jirislaby, p.zabel
Cc: tony.huang, wells.lu, hammer.hsieh
This is a patch series for UART driver for Suplus SP7021 SoC.
Sunplus SP7021 is an ARM Cortex A7 (4 cores) based SoC. It integrates
many peripherals (ex: UART. I2C, SPI, SDIO, eMMC, USB, SD card and
etc.) into a single chip. It is designed for industrial control.
Refer to:
https://sunplus-tibbo.atlassian.net/wiki/spaces/doc/overview
https://tibbo.com/store/plus1.html
hammer.hsieh (2):
dt-bindings:serial:Add bindings doc for Sunplus SoC UART Driver
serial:sunplus-uart:Add Sunplus SoC UART Driver
.../devicetree/bindings/serial/sunplus,uart.yaml | 116 ++
MAINTAINERS | 7 +
drivers/tty/serial/Kconfig | 23 +
drivers/tty/serial/Makefile | 1 +
drivers/tty/serial/sunplus-uart.c | 1848 ++++++++++++++++++++
include/soc/sunplus/sp_uart.h | 158 ++
6 files changed, 2153 insertions(+)
create mode 100644 Documentation/devicetree/bindings/serial/sunplus,uart.yaml
create mode 100644 drivers/tty/serial/sunplus-uart.c
create mode 100644 include/soc/sunplus/sp_uart.h
--
2.7.4
^ permalink raw reply [flat|nested] 19+ messages in thread
* [PATCH 1/2] dt-bindings:serial:Add bindings doc for Sunplus SoC UART Driver
2021-11-01 7:48 [PATCH 0/2] Add UART driver for Suplus SP7021 SoC hammer.hsieh
@ 2021-11-01 7:48 ` hammer.hsieh
2021-11-01 13:20 ` Rob Herring
2021-11-01 19:34 ` Rob Herring
2021-11-01 7:48 ` [PATCH 2/2] serial:sunplus-uart:Add " hammer.hsieh
` (2 subsequent siblings)
3 siblings, 2 replies; 19+ messages in thread
From: hammer.hsieh @ 2021-11-01 7:48 UTC (permalink / raw)
To: gregkh, linux-serial, devicetree, linux-kernel, jirislaby, p.zabel
Cc: tony.huang, wells.lu, hammer.hsieh
Add bindings doc for Sunplus SoC UART Driver
Signed-off-by: hammer.hsieh <hammer.hsieh@sunplus.com>
---
.../devicetree/bindings/serial/sunplus,uart.yaml | 116 +++++++++++++++++++++
MAINTAINERS | 5 +
2 files changed, 121 insertions(+)
create mode 100644 Documentation/devicetree/bindings/serial/sunplus,uart.yaml
diff --git a/Documentation/devicetree/bindings/serial/sunplus,uart.yaml b/Documentation/devicetree/bindings/serial/sunplus,uart.yaml
new file mode 100644
index 0000000..f2ca9ee
--- /dev/null
+++ b/Documentation/devicetree/bindings/serial/sunplus,uart.yaml
@@ -0,0 +1,116 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+# Copyright (C) Sunplus Co., Ltd. 2021
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/serial/sunplus,uart.yaml#"
+$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+
+title: Sunplus SoC UART Controller Device Tree Bindings
+
+maintainers:
+ - Tony Huang <tony.huang@sunplus.com>
+ - Hammer Hsieh <hammer.hsieh@sunplus.com>
+ - Wells Lu <wells.lu@sunplus.com>
+
+allOf:
+ - $ref: serial.yaml#
+
+properties:
+ compatible:
+ const: sunplus,sp7021-uart
+
+ reg:
+ minItems: 1
+ maxItems: 2
+
+ interrupts:
+ maxItems: 1
+
+ clocks:
+ minItems: 1
+ maxItems: 2
+
+ clock-names:
+ oneOf:
+ - items:
+ - const: UADMA
+ - const: PERI0
+ - items:
+ - const: UADMA
+ - const: PERI1
+ - items:
+ - const: HWUA
+ - const: PERI0
+ - items:
+ - const: HWUA
+ - const: PERI1
+
+ resets:
+ maxItems: 1
+
+ which-uart:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [ 1, 2, 3, 4]
+
+required:
+ - compatible
+ - reg
+ - clocks
+ - resets
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/irq.h>
+ #include <dt-bindings/clock/sp-sp7021.h>
+ #include <dt-bindings/reset/sp-sp7021.h>
+ aliases {
+ serial0 = &uart0;
+ serial1 = &uart1;
+ serial10 = &uartdmarx0;
+ serial20 = &uartdmatx0;
+ };
+
+ uart0: serial@9c000900 {
+ compatible = "sunplus,sp7021-uart";
+ reg = <0x9c000900 0x80>;
+ interrupt-parent = <&intc>;
+ interrupts = <53 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clkc UA0>;
+ resets = <&rstc RST_UA0>;
+ };
+
+ // UART1 PIO mode
+ uart1: serial@9c000980 {
+ compatible = "sunplus,sp7021-uart";
+ reg = <0x9c000980 0x80>;
+ interrupt-parent = <&intc>;
+ interrupts = <54 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clkc UA1>;
+ resets = <&rstc RST_UA1>;
+ };
+
+ // UART1 DMA mode for RX
+ uartdmarx0: serial@9c008980 {
+ compatible = "sunplus,sp7021-uart";
+ reg = <0x9c008980 0x40>;
+ interrupt-parent = <&intc>;
+ interrupts = <138 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clkc UADMA>, <&clkc PERI0>;
+ clock-names = "UADMA", "PERI0";
+ resets = <&rstc RST_UADMA>;
+ which-uart = <1>;
+ };
+
+ // UART1 DMA mode for TX
+ uartdmatx0: serial@9c008a00 {
+ compatible = "sunplus,sp7021-uart";
+ reg = <0x9c008a00 0x40>, <0x9c008880 0x80>;
+ clocks = <&clkc HWUA>, <&clkc PERI0>;
+ clock-names = "HWUA", "PERI0";
+ resets = <&rstc RST_HWUA>;
+ which-uart = <1>;
+ };
+
+...
diff --git a/MAINTAINERS b/MAINTAINERS
index 3b79fd4..f863e97 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -17945,6 +17945,11 @@ L: netdev@vger.kernel.org
S: Maintained
F: drivers/net/ethernet/dlink/sundance.c
+SUNPLUS UART DRIVER
+M: Hammer Hsieh <hammer.hsieh@sunplus.com>
+S: Maintained
+F: Documentation/devicetree/bindings/serial/sunplus,uart.yaml
+
SUPERH
M: Yoshinori Sato <ysato@users.sourceforge.jp>
M: Rich Felker <dalias@libc.org>
--
2.7.4
^ permalink raw reply related [flat|nested] 19+ messages in thread
* [PATCH 2/2] serial:sunplus-uart:Add Sunplus SoC UART Driver
2021-11-01 7:48 [PATCH 0/2] Add UART driver for Suplus SP7021 SoC hammer.hsieh
2021-11-01 7:48 ` [PATCH 1/2] dt-bindings:serial:Add bindings doc for Sunplus SoC UART Driver hammer.hsieh
@ 2021-11-01 7:48 ` hammer.hsieh
2021-11-01 7:56 ` Greg KH
2021-11-10 7:51 ` [PATCH v2 0/2] Add UART driver for Suplus SP7021 SoC Hammer Hsieh
2021-11-19 5:19 ` [PATCH v3 " Hammer Hsieh
3 siblings, 1 reply; 19+ messages in thread
From: hammer.hsieh @ 2021-11-01 7:48 UTC (permalink / raw)
To: gregkh, linux-serial, devicetree, linux-kernel, jirislaby, p.zabel
Cc: tony.huang, wells.lu, hammer.hsieh
Add Sunplus SoC UART Driver
Signed-off-by: hammer.hsieh <hammer.hsieh@sunplus.com>
---
MAINTAINERS | 2 +
drivers/tty/serial/Kconfig | 23 +
drivers/tty/serial/Makefile | 1 +
drivers/tty/serial/sunplus-uart.c | 1848 +++++++++++++++++++++++++++++++++++++
include/soc/sunplus/sp_uart.h | 158 ++++
5 files changed, 2032 insertions(+)
create mode 100644 drivers/tty/serial/sunplus-uart.c
create mode 100644 include/soc/sunplus/sp_uart.h
diff --git a/MAINTAINERS b/MAINTAINERS
index f863e97..0176026 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -17949,6 +17949,8 @@ SUNPLUS UART DRIVER
M: Hammer Hsieh <hammer.hsieh@sunplus.com>
S: Maintained
F: Documentation/devicetree/bindings/serial/sunplus,uart.yaml
+F: drivers/tty/serial/sunplus-uart.c
+F: include/soc/sunplus/sp-uart.h
SUPERH
M: Yoshinori Sato <ysato@users.sourceforge.jp>
diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig
index 131a6a5..319f5db 100644
--- a/drivers/tty/serial/Kconfig
+++ b/drivers/tty/serial/Kconfig
@@ -1561,6 +1561,29 @@ config SERIAL_LITEUART_CONSOLE
and warnings and which allows logins in single user mode).
Otherwise, say 'N'.
+config SERIAL_SUNPLUS
+ bool "Sunplus UART support"
+ depends on OF
+ select SERIAL_CORE
+ help
+ Select this option if you would like to use Sunplus serial port on
+ Sunplus SoC SP7021.
+ If you enable this option, Sunplus serial ports in the system will
+ be registered as ttySx.
+
+config SERIAL_SUNPLUS_CONSOLE
+ bool "Console on Sunplus UART"
+ depends on SERIAL_SUNPLUS
+ select SERIAL_CORE_CONSOLE
+ select SERIAL_EARLYCON
+ help
+ Select this option if you would like to use a Sunplus UART as the
+ system console.
+ Even if you say Y here, the currently visible virtual console
+ (/dev/tty0) will still be used as the system console by default, but
+ you can alter that using a kernel command line option such as
+ "console=ttySx".
+
endmenu
config SERIAL_MCTRL_GPIO
diff --git a/drivers/tty/serial/Makefile b/drivers/tty/serial/Makefile
index 7da0856..61cc8de 100644
--- a/drivers/tty/serial/Makefile
+++ b/drivers/tty/serial/Makefile
@@ -87,6 +87,7 @@ obj-$(CONFIG_SERIAL_RDA) += rda-uart.o
obj-$(CONFIG_SERIAL_MILBEAUT_USIO) += milbeaut_usio.o
obj-$(CONFIG_SERIAL_SIFIVE) += sifive.o
obj-$(CONFIG_SERIAL_LITEUART) += liteuart.o
+obj-$(CONFIG_SERIAL_SUNPLUS) += sunplus-uart.o
# GPIOLIB helpers for modem control lines
obj-$(CONFIG_SERIAL_MCTRL_GPIO) += serial_mctrl_gpio.o
diff --git a/drivers/tty/serial/sunplus-uart.c b/drivers/tty/serial/sunplus-uart.c
new file mode 100644
index 0000000..d1524dc
--- /dev/null
+++ b/drivers/tty/serial/sunplus-uart.c
@@ -0,0 +1,1848 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Sunplus SoC UART driver
+ *
+ * Author: Hammer Hsieh <hammer.hsieh@sunplus.com>
+ * Tony Huang <tony.huang@sunplus.com>
+ * Wells Lu <wells.lu@sunplus.com>
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/console.h>
+#include <linux/interrupt.h>
+#include <linux/platform_device.h>
+#include <linux/tty.h>
+#include <linux/tty_flip.h>
+#include <linux/of_platform.h>
+#include <asm/irq.h>
+#if defined(CONFIG_MAGIC_SYSRQ)
+#define SUPPORT_SYSRQ
+#include <linux/sysrq.h>
+#endif
+#include <linux/serial_core.h>
+#include <linux/clk.h>
+#include <linux/reset.h>
+#include <linux/io.h>
+#include <linux/dma-mapping.h>
+#include <soc/sunplus/sp_uart.h>
+
+#ifdef CONFIG_PM_RUNTIME_UART
+#include <linux/pm_runtime.h>
+#endif
+
+#include <linux/gpio.h>
+#include <linux/of.h>
+#include <linux/of_gpio.h>
+#include <dt-bindings/clock/sp-sp7021.h>
+#include <dt-bindings/pinctrl/sppctl-sp7021.h>
+#include <linux/delay.h>
+#include <linux/hrtimer.h>
+
+#define DEVICE_NAME "ttyS"
+#define SP_UART_MAJOR TTY_MAJOR
+#define SP_UART_MINOR_START 64
+
+#define NUM_UART 6 /* serial0, ... */
+#define NUM_UARTDMARX 2 /* serial10, ... */
+#define NUM_UARTDMATX 2 /* serial20, ... */
+
+#define ID_BASE_DMARX 10
+#define ID_BASE_DMATX 20
+
+#define IS_UARTDMARX_ID(X) \
+ (((X) >= (ID_BASE_DMARX)) && ((X) < (ID_BASE_DMARX + NUM_UARTDMARX)))
+#define IS_UARTDMATX_ID(X) \
+ (((X) >= (ID_BASE_DMATX)) && ((X) < (ID_BASE_DMATX + NUM_UARTDMATX)))
+
+//#define TTYS_KDBG_INFO
+#define TTYS_KDBG_ERR
+//#define TTYS_GPIO
+
+#ifdef TTYS_KDBG_INFO
+#define DBG_INFO(fmt, args ...) pr_info("K_TTYS: " fmt, ## args)
+#else
+#define DBG_INFO(fmt, args ...)
+#endif
+#ifdef TTYS_KDBG_ERR
+#define DBG_ERR(fmt, args ...) pr_err("K_TTYS: " fmt, ## args)
+#else
+#define DBG_ERR(fmt, args ...)
+#endif
+
+#define SP_UART_CREAD_DISABLED (1 << 16)
+
+#define UARXDMA_BUF_SZ PAGE_SIZE
+#define MAX_SZ_RXDMA_ISR (1 << 9)
+#define UATXDMA_BUF_SZ PAGE_SIZE
+
+#define CLK_HIGH_UART 202500000
+#define UART_RATIO 232
+
+#if defined(CONFIG_SP_MON)
+extern unsigned int uart0_mask_tx; /* Used for masking uart0 tx output */
+#endif
+
+struct sunplus_uart_port {
+ char name[16];
+ struct uart_port uport;
+ struct sunplus_uartdma_info *uartdma_rx;
+ struct sunplus_uartdma_info *uartdma_tx;
+ struct clk *clk;
+ struct reset_control *rstc;
+ struct gpio_desc *rts_gpio;
+ struct hrtimer CheckTXE;
+ struct hrtimer DelayRtsBeforeSend;
+ struct hrtimer DelayRtsAfterSend;
+};
+struct sunplus_uart_port sunplus_uart_ports[NUM_UART];
+
+struct sunplus_uartdma_info {
+ void __iomem *membase; /* virtual address */
+ unsigned long addr_phy;
+ void __iomem *gdma_membase; /* virtual address */
+ int irq;
+ int which_uart;
+ struct sunplus_uart_port *binding_port;
+ void *buf_va;
+ dma_addr_t dma_handle;
+};
+static struct sunplus_uartdma_info
+ sunplus_uartdma[NUM_UARTDMARX + NUM_UARTDMATX];
+
+static inline void sp_uart_set_int_en(unsigned char __iomem *base,
+ unsigned int int_state)
+{
+ writel(int_state, &((struct regs_uart *)base)->uart_isc);
+}
+
+static inline unsigned int sp_uart_get_int_en(unsigned char __iomem *base)
+{
+ return readl(&((struct regs_uart *)base)->uart_isc);
+}
+
+static inline int sp_uart_get_char(unsigned char __iomem *base)
+{
+ return readl(&((struct regs_uart *)base)->uart_data);
+}
+
+static inline void sp_uart_put_char(struct uart_port *port, unsigned int ch)
+{
+ struct sunplus_uart_port *sp_port =
+ (struct sunplus_uart_port *)(port->private_data);
+ struct sunplus_uartdma_info *uartdma_tx =
+ sp_port->uartdma_tx;
+ struct regs_uatxdma *txdma_reg;
+ unsigned char __iomem *base = port->membase;
+ u32 addr_sw, addr_start;
+ u32 offset_sw;
+ u8 *byte_ptr;
+
+#if defined(CONFIG_SP_MON)
+ if ((uart0_mask_tx == 1) && ((u32)base == LOGI_ADDR_UART0_REG))
+ return;
+#endif
+
+ if (!uartdma_tx) {
+ writel(ch, &((struct regs_uart *)base)->uart_data);
+ } else {
+ txdma_reg = (struct regs_uatxdma *)(uartdma_tx->membase);
+ addr_sw = readl(&(txdma_reg->txdma_wr_adr));
+ addr_start = readl(&(txdma_reg->txdma_start_addr));
+ offset_sw = addr_sw - addr_start;
+ byte_ptr = (u8 *)(uartdma_tx->buf_va + offset_sw);
+ *byte_ptr = (u8)(ch);
+ if (offset_sw == (UATXDMA_BUF_SZ - 1))
+ writel((u32)(uartdma_tx->dma_handle), &(txdma_reg->txdma_wr_adr));
+ else
+ writel((addr_sw + 1), &(txdma_reg->txdma_wr_adr));
+ }
+}
+
+static inline unsigned int sp_uart_get_line_status(unsigned char __iomem *base)
+{
+ return readl(&((struct regs_uart *)base)->uart_lsr);
+}
+
+static inline u32 sp_uart_line_status_tx_buf_not_full(struct uart_port *port)
+{
+ struct sunplus_uart_port *sp_port =
+ (struct sunplus_uart_port *)(port->private_data);
+ struct sunplus_uartdma_info *uartdma_tx =
+ sp_port->uartdma_tx;
+ struct regs_uatxdma *txdma_reg;
+ unsigned char __iomem *base = port->membase;
+ u32 addr_sw, addr_hw;
+
+ if (uartdma_tx) {
+ txdma_reg = (struct regs_uatxdma *)(uartdma_tx->membase);
+ if (readl(&(txdma_reg->txdma_status)) & 0x01)
+ return 0;
+
+ addr_sw = readl(&(txdma_reg->txdma_wr_adr));
+ addr_hw = readl(&(txdma_reg->txdma_rd_adr));
+ if (addr_sw >= addr_hw)
+ return (UATXDMA_BUF_SZ - (addr_sw - addr_hw));
+ else
+ return (addr_hw - addr_sw);
+
+ } else {
+ if (readl(&((struct regs_uart *)base)->uart_lsr) & SP_UART_LSR_TX) {
+ /*
+ * In PIO mode, just return 1 byte
+ * becauase exactly number is unknown
+ */
+ return 1;
+ } else {
+ return 0;
+ }
+ }
+}
+
+static inline void sp_uart_set_line_ctrl(unsigned char __iomem *base,
+ unsigned int ctrl)
+{
+ writel(ctrl, &((struct regs_uart *)base)->uart_lcr);
+}
+
+static inline unsigned int sp_uart_get_line_ctrl(unsigned char __iomem *base)
+{
+ return readl(&((struct regs_uart *)base)->uart_lcr);
+}
+
+static inline void sp_uart_set_divider_low_register(unsigned char __iomem *base,
+ unsigned int val)
+{
+ writel(val, &((struct regs_uart *)base)->uart_div_l);
+}
+
+static inline unsigned int sp_uart_get_divider_low_register(unsigned char __iomem *base)
+{
+ return readl(&((struct regs_uart *)base)->uart_div_l);
+}
+
+static inline void sp_uart_set_divider_high_register(unsigned char __iomem *base,
+ unsigned int val)
+{
+ writel(val, &((struct regs_uart *)base)->uart_div_h);
+}
+
+static inline unsigned int sp_uart_get_divider_high_register(unsigned char __iomem *base)
+{
+ return readl(&((struct regs_uart *)base)->uart_div_h);
+}
+
+static inline void sp_uart_set_rx_residue(unsigned char __iomem *base,
+ unsigned int val)
+{
+ writel(val, &((struct regs_uart *)base)->uart_rx_residue);
+}
+
+static inline void sp_uart_set_modem_ctrl(unsigned char __iomem *base,
+ unsigned int val)
+{
+ writel(val, &((struct regs_uart *)base)->uart_mcr);
+}
+
+static inline unsigned int sp_uart_get_modem_ctrl(unsigned char __iomem *base)
+{
+ return readl(&((struct regs_uart *)base)->uart_mcr);
+}
+
+static inline void sp_uart_set_clk_src(unsigned char __iomem *base,
+ unsigned int val)
+{
+ writel(val, &((struct regs_uart *)base)->uart_clk_src);
+}
+
+/*
+ * Note:
+ * When (uart0_as_console == 0), please make sure:
+ * There is no "console=ttyS0,115200", "earlyprintk", ... in kernel command line.
+ * In /etc/inittab, there is no something like "ttyS0::respawn:/bin/sh"
+ */
+unsigned int uart0_as_console = ~0;
+unsigned int uart_enable_status = ~0; /* bit 0: UART0, bit 1: UART1, ... */
+
+#if defined(CONFIG_SP_MON)
+extern int sysrqCheckState(char, struct uart_port *);
+#endif
+
+static struct sunplus_uartdma_info *sunplus_uartdma_rx_binding(int id)
+{
+ int i;
+
+ for (i = 0; i < NUM_UARTDMARX; i++) {
+ if ((sunplus_uartdma[i].which_uart == id) && (sunplus_uartdma[i].membase)) {
+ sunplus_uartdma[i].binding_port = &sunplus_uart_ports[id];
+ return &sunplus_uartdma[i];
+ }
+ }
+ return NULL;
+}
+
+static struct sunplus_uartdma_info *sunplus_uartdma_tx_binding(int id)
+{
+ int i;
+
+ for (i = NUM_UARTDMARX; i < (NUM_UARTDMARX + NUM_UARTDMATX); i++) {
+ if ((sunplus_uartdma[i].which_uart == id) && (sunplus_uartdma[i].membase)) {
+ sunplus_uartdma[i].binding_port = &sunplus_uart_ports[id];
+ return &sunplus_uartdma[i];
+ }
+ }
+ return NULL;
+}
+
+static inline void wait_for_xmitr(struct uart_port *port)
+{
+ while (1) {
+ if (sp_uart_line_status_tx_buf_not_full(port))
+ break;
+ }
+}
+
+static unsigned int sunplus_uart_ops_tx_empty(struct uart_port *port)
+{
+ struct sunplus_uart_port *sp_port = (struct sunplus_uart_port *)(port->private_data);
+ struct sunplus_uartdma_info *uartdma_tx = sp_port->uartdma_tx;
+ struct regs_uatxdma *txdma_reg;
+
+ if (uartdma_tx) {
+ txdma_reg = (struct regs_uatxdma *)(uartdma_tx->membase);
+ if (readl(&(txdma_reg->txdma_status)) & 0x02)
+ return TIOCSER_TEMT;
+ else
+ return 0;
+ } else {
+ return ((sp_uart_get_line_status(port->membase) & SP_UART_LSR_TXE)
+ ? TIOCSER_TEMT : 0);
+ }
+}
+
+static void sunplus_uart_ops_set_mctrl(struct uart_port *port, unsigned int mctrl)
+{
+ struct sunplus_uart_port *sp_port =
+ (struct sunplus_uart_port *)(port->private_data);
+ unsigned char mcr = sp_uart_get_modem_ctrl(port->membase);
+ ktime_t ktime;
+
+ if (mctrl & TIOCM_DTR)
+ mcr |= SP_UART_MCR_DTS;
+ else
+ mcr &= ~SP_UART_MCR_DTS;
+
+ if (mctrl & TIOCM_RTS) {
+ if ((sp_port->uport.rs485.flags & SER_RS485_ENABLED)
+ && (sp_port->uport.rs485.flags & SER_RS485_RTS_ON_SEND))
+ mcr &= ~SP_UART_MCR_RTS; /* RTS invert */
+ else
+ mcr |= SP_UART_MCR_RTS;
+ } else {
+ /* data transfer ended */
+ if (sp_port->uport.rs485.flags & SER_RS485_ENABLED)
+ return;
+
+ mcr &= ~SP_UART_MCR_RTS;
+ }
+
+ if (mctrl & TIOCM_CAR)
+ mcr |= SP_UART_MCR_DCD;
+ else
+ mcr &= ~SP_UART_MCR_DCD;
+
+ if (mctrl & TIOCM_RI)
+ mcr |= SP_UART_MCR_RI;
+ else
+ mcr &= ~SP_UART_MCR_RI;
+
+ if (mctrl & TIOCM_LOOP)
+ mcr |= SP_UART_MCR_LB;
+ else
+ mcr &= ~SP_UART_MCR_LB;
+
+ sp_uart_set_modem_ctrl(port->membase, mcr);
+
+ if (sp_port->uport.rs485.flags & SER_RS485_ENABLED) {
+ mcr = sp_uart_get_modem_ctrl(port->membase);
+ if (mctrl & TIOCM_RTS) {
+ if (((mcr & SP_UART_MCR_RTS)
+ && (sp_port->uport.rs485.flags & SER_RS485_RTS_AFTER_SEND))
+ || (sp_port->uport.rs485.flags & SER_RS485_RTS_ON_SEND)) {
+ if (!IS_ERR(sp_port->rts_gpio))
+ gpiod_set_value(sp_port->rts_gpio, 1);
+ dev_dbg(port->dev, "%s set rts_gpio=1\n", port->name);
+ if (sp_port->uport.rs485.delay_rts_before_send == 0) {
+ ktime = ktime_set(0, 500000); /* 500us */
+ hrtimer_start(&sp_port->CheckTXE, ktime, HRTIMER_MODE_REL);
+ }
+ }
+ }
+ }
+}
+
+static unsigned int sunplus_uart_ops_get_mctrl(struct uart_port *port)
+{
+ unsigned char status;
+ unsigned int ret = 0;
+
+ status = sp_uart_get_modem_ctrl(port->membase);
+
+ if (status & SP_UART_MCR_DTS)
+ ret |= TIOCM_DTR;
+
+ if (status & SP_UART_MCR_RTS)
+ ret |= TIOCM_RTS;
+
+ if (status & SP_UART_MCR_DCD)
+ ret |= TIOCM_CAR;
+
+ if (status & SP_UART_MCR_RI)
+ ret |= TIOCM_RI;
+
+ if (status & SP_UART_MCR_LB)
+ ret |= TIOCM_LOOP;
+
+ if (status & SP_UART_MCR_AC)
+ ret |= TIOCM_CTS;
+
+ return ret;
+}
+
+static void sunplus_uart_ops_stop_tx(struct uart_port *port)
+{
+ unsigned int isc = sp_uart_get_int_en(port->membase);
+
+ /*
+ * Even if (uartdma_tx != NULL), "BUF_NOT_FULL" interrupt
+ * is used for getting into ISR
+ */
+ isc &= ~SP_UART_ISC_TXM;
+ sp_uart_set_int_en(port->membase, isc);
+}
+
+static inline void __start_tx(struct uart_port *port)
+{
+ unsigned int isc;
+
+ isc = sp_uart_get_int_en(port->membase) | SP_UART_ISC_TXM;
+ sp_uart_set_int_en(port->membase, isc);
+}
+
+static void sunplus_uart_ops_start_tx(struct uart_port *port)
+{
+ struct sunplus_uart_port *sp_port =
+ (struct sunplus_uart_port *)(port->private_data);
+ ktime_t ktime;
+ int val;
+
+ if (sp_port->uport.rs485.flags & SER_RS485_ENABLED) {
+ val = (sp_port->uport.rs485.flags & SER_RS485_RTS_ON_SEND ? 1 : 0);
+ if (!IS_ERR(sp_port->rts_gpio))
+ gpiod_set_value(sp_port->rts_gpio, val);
+
+ dev_dbg(port->dev, "%s set rts_gpio=%d\n", sp_port->uport.name, val);
+ if (sp_port->uport.rs485.delay_rts_before_send > 0) {
+ long nsec = sp_port->uport.rs485.delay_rts_before_send * 1000000;
+
+ ktime = ktime_set(0, nsec);
+ hrtimer_start(&sp_port->DelayRtsBeforeSend, ktime, HRTIMER_MODE_REL);
+ return;
+ }
+ }
+ __start_tx(port);
+}
+
+static void sunplus_uart_ops_stop_rx(struct uart_port *port)
+{
+ unsigned int isc;
+
+ isc = sp_uart_get_int_en(port->membase);
+ isc &= ~SP_UART_ISC_RXM;
+ sp_uart_set_int_en(port->membase, isc);
+}
+
+static void sunplus_uart_ops_enable_ms(struct uart_port *port)
+{
+ /* Do nothing */
+}
+
+static void sunplus_uart_ops_break_ctl(struct uart_port *port, int ctl)
+{
+ unsigned long flags;
+ unsigned int h_lcr;
+
+ spin_lock_irqsave(&port->lock, flags);
+
+ h_lcr = sp_uart_get_line_ctrl(port->membase);
+ if (ctl != 0)
+ h_lcr |= SP_UART_LCR_BC; /* start break */
+ else
+ h_lcr &= ~SP_UART_LCR_BC; /* stop break */
+
+ sp_uart_set_line_ctrl(port->membase, h_lcr);
+
+ spin_unlock_irqrestore(&port->lock, flags);
+}
+
+static void transmit_chars(struct uart_port *port)
+{
+ struct sunplus_uart_port *sp_port =
+ (struct sunplus_uart_port *)(port->private_data);
+ struct sunplus_uartdma_info *uartdma_tx = sp_port->uartdma_tx;
+ u32 tx_buf_available;
+ struct regs_uatxdma *txdma_reg;
+ u32 addr_sw, addr_start;
+ u32 offset_sw;
+ u8 *byte_ptr;
+ struct circ_buf *xmit = &port->state->xmit;
+
+ if (port->x_char) {
+ sp_uart_put_char(port, port->x_char);
+ port->icount.tx++;
+ port->x_char = 0;
+ return;
+ }
+
+ if (uart_circ_empty(xmit) || uart_tx_stopped(port)) {
+ sunplus_uart_ops_stop_tx(port);
+ return;
+ }
+
+ if (uartdma_tx) {
+ txdma_reg = (struct regs_uatxdma *)(uartdma_tx->membase);
+ addr_sw = readl(&(txdma_reg->txdma_wr_adr));
+ addr_start = readl(&(txdma_reg->txdma_start_addr));
+ offset_sw = addr_sw - addr_start;
+ byte_ptr = (u8 *)(uartdma_tx->buf_va + offset_sw);
+ tx_buf_available = sp_uart_line_status_tx_buf_not_full(port);
+ while (tx_buf_available) {
+ *byte_ptr = xmit->buf[xmit->tail];
+ xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
+ port->icount.tx++;
+
+ byte_ptr++;
+ addr_sw++;
+ offset_sw++;
+ tx_buf_available--;
+ if (offset_sw == UATXDMA_BUF_SZ) {
+ offset_sw = 0;
+ addr_sw = (u32)(uartdma_tx->dma_handle);
+ byte_ptr = (u8 *)(uartdma_tx->buf_va);
+ }
+
+ if (uart_circ_empty(xmit))
+ break;
+ }
+ writel(addr_sw, &(txdma_reg->txdma_wr_adr));
+ } else {
+ do {
+ sp_uart_put_char(port, xmit->buf[xmit->tail]);
+ xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
+ port->icount.tx++;
+
+ if (uart_circ_empty(xmit))
+ break;
+ } while (sp_uart_line_status_tx_buf_not_full(port));
+ }
+
+ if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
+ uart_write_wakeup(port);
+
+ if (uart_circ_empty(xmit))
+ sunplus_uart_ops_stop_tx(port);
+}
+
+/* called by ISR */
+static void receive_chars(struct uart_port *port)
+{
+ struct tty_struct *tty = port->state->port.tty;
+ unsigned char lsr = sp_uart_get_line_status(port->membase);
+ unsigned int ch, flag;
+
+ do {
+ ch = sp_uart_get_char(port->membase);
+
+#if defined(CONFIG_SP_MON)
+ if (sysrqCheckState(ch, port) != 0)
+ goto ignore_char;
+#endif
+
+ flag = TTY_NORMAL;
+ port->icount.rx++;
+
+ if (unlikely(lsr & SP_UART_LSR_BRK_ERROR_BITS)) {
+ if (port->cons == NULL)
+ DBG_ERR("UART%d, SP_UART_LSR_BRK_ERROR_BITS, lsr = 0x%08X\n",
+ port->line, lsr);
+
+ if (lsr & SP_UART_LSR_BC) {
+ lsr &= ~(SP_UART_LSR_FE | SP_UART_LSR_PE);
+ port->icount.brk++;
+ if (uart_handle_break(port))
+ goto ignore_char;
+ } else if (lsr & SP_UART_LSR_PE) {
+ if (port->cons == NULL)
+ DBG_ERR("UART%d, SP_UART_LSR_PE\n", port->line);
+ port->icount.parity++;
+ } else if (lsr & SP_UART_LSR_FE) {
+ if (port->cons == NULL)
+ DBG_ERR("UART%d, SP_UART_LSR_FE\n", port->line);
+ port->icount.frame++;
+ }
+ if (lsr & SP_UART_LSR_OE) {
+ if (port->cons == NULL)
+ DBG_ERR("UART%d, SP_UART_LSR_OE\n", port->line);
+ port->icount.overrun++;
+ }
+
+ /*
+ * Mask off conditions which should be ignored.
+ */
+
+ /* lsr &= port->read_status_mask; */
+
+ if (lsr & SP_UART_LSR_BC)
+ flag = TTY_BREAK;
+ else if (lsr & SP_UART_LSR_PE)
+ flag = TTY_PARITY;
+ else if (lsr & SP_UART_LSR_FE)
+ flag = TTY_FRAME;
+ }
+
+ if (port->ignore_status_mask & SP_UART_CREAD_DISABLED)
+ goto ignore_char;
+
+ if (uart_handle_sysrq_char(port, ch))
+ goto ignore_char;
+
+ uart_insert_char(port, lsr, SP_UART_LSR_OE, ch, flag);
+
+ignore_char:
+ lsr = sp_uart_get_line_status(port->membase);
+ } while (lsr & SP_UART_LSR_RX);
+
+ if (tty) {
+ spin_unlock(&port->lock);
+ tty_flip_buffer_push(tty->port);
+ spin_lock(&port->lock);
+ }
+}
+
+static irqreturn_t sunplus_uart_irq(int irq, void *args)
+{
+ struct uart_port *port = (struct uart_port *)args;
+ unsigned long flags;
+
+ spin_lock_irqsave(&port->lock, flags);
+
+ if (sp_uart_get_int_en(port->membase) & SP_UART_ISC_RX)
+ receive_chars(port);
+
+ if (sp_uart_get_int_en(port->membase) & SP_UART_ISC_TX)
+ transmit_chars(port);
+
+ spin_unlock_irqrestore(&port->lock, flags);
+
+ return IRQ_HANDLED;
+}
+
+/* called by ISR */
+static void receive_chars_rxdma(struct uart_port *port)
+{
+ struct sunplus_uart_port *sp_port =
+ (struct sunplus_uart_port *)(port->private_data);
+ struct sunplus_uartdma_info *uartdma_rx;
+ struct regs_uarxdma *rxdma_reg;
+ struct tty_struct *tty = port->state->port.tty;
+ u32 offset_sw, offset_hw, rx_size, dma_start;
+ u8 *sw_ptr, *buf_end_ptr, *u8_ptr;
+ u32 icount_rx;
+ u32 tmp_u32;
+ u8 tmp_buf[32];
+ int i;
+
+ uartdma_rx = sp_port->uartdma_rx;
+ rxdma_reg = (struct regs_uarxdma *)(uartdma_rx->membase);
+
+ dma_start = readl(&(rxdma_reg->rxdma_start_addr));
+ offset_sw = readl(&(rxdma_reg->rxdma_rd_adr)) - dma_start;
+ offset_hw = readl(&(rxdma_reg->rxdma_wr_adr)) - dma_start;
+
+ if (offset_hw >= offset_sw)
+ rx_size = offset_hw - offset_sw;
+ else
+ rx_size = offset_hw + UARXDMA_BUF_SZ - offset_sw;
+
+ sw_ptr = (u8 *)(uartdma_rx->buf_va + offset_sw);
+ buf_end_ptr = (u8 *)(uartdma_rx->buf_va + UARXDMA_BUF_SZ);
+
+ /*
+ * Retrieve all data in ISR.
+ * The max. received size is (buffer_size - threshold_size)
+ * = (rxdma_length_thr[31:16] - rxdma_length_thr[15:0]) = MAX_SZ_RXDMA_ISR
+ * In order to limit the execution time in this ISR:
+ * => Increase rxdma_length_thr[15:0] to shorten each ISR execution time.
+ * => Don't need to set a small threshold_size,
+ * and split a long ISR into several shorter ISRs.
+ */
+ icount_rx = 0;
+ while (rx_size > icount_rx) {
+ /* 32-byte aligned */
+ if (!(((unsigned long)(sw_ptr)) & (32 - 1))
+ && ((rx_size - icount_rx) >= 32)) {
+ /*
+ * Copy 32 bytes data from non cache area to cache area.
+ * => It should use less DRAM controller's read command.
+ */
+ memcpy(tmp_buf, sw_ptr, 32);
+ u8_ptr = (u8 *)(tmp_buf);
+ for (i = 0; i < 32; i++) {
+ port->icount.rx++;
+ uart_insert_char(port, 0, SP_UART_LSR_OE,
+ (unsigned int)(*u8_ptr), TTY_NORMAL);
+ u8_ptr++;
+ }
+ sw_ptr += 32;
+ icount_rx += 32;
+ } else {
+ port->icount.rx++;
+ uart_insert_char(port, 0, SP_UART_LSR_OE,
+ (unsigned int)(*sw_ptr), TTY_NORMAL);
+ sw_ptr++;
+ icount_rx++;
+ }
+ if (sw_ptr >= buf_end_ptr)
+ sw_ptr = (u8 *)(uartdma_rx->buf_va);
+ }
+ tmp_u32 = readl(&(rxdma_reg->rxdma_rd_adr)) + rx_size;
+ if (tmp_u32 <= readl(&(rxdma_reg->rxdma_end_addr)))
+ writel(tmp_u32, &(rxdma_reg->rxdma_rd_adr));
+ else
+ writel((tmp_u32 - UARXDMA_BUF_SZ), &(rxdma_reg->rxdma_rd_adr));
+
+ spin_unlock(&port->lock);
+ tty_flip_buffer_push(tty->port);
+ spin_lock(&port->lock);
+
+ writel(readl(&(rxdma_reg->rxdma_enable_sel)) | DMA_INT,
+ &(rxdma_reg->rxdma_enable_sel));
+ writel(readl(&(rxdma_reg->rxdma_enable_sel)) | DMA_GO,
+ &(rxdma_reg->rxdma_enable_sel));
+}
+
+static irqreturn_t sunplus_uart_rxdma_irq(int irq, void *args)
+{
+ struct uart_port *port = (struct uart_port *)args;
+ unsigned long flags;
+
+ spin_lock_irqsave(&port->lock, flags);
+#ifdef TTYS_GPIO
+ gpio_set_value(0, 1);
+#endif
+ receive_chars_rxdma(port);
+
+ spin_unlock_irqrestore(&port->lock, flags);
+
+ return IRQ_HANDLED;
+}
+
+static int sunplus_uart_ops_startup(struct uart_port *port)
+{
+ int ret;
+ u32 timeout, interrupt_en;
+ struct sunplus_uart_port *sp_port =
+ (struct sunplus_uart_port *)(port->private_data);
+ struct sunplus_uartdma_info *uartdma_rx, *uartdma_tx;
+ struct regs_uarxdma *rxdma_reg;
+ struct regs_uatxdma *txdma_reg;
+ struct regs_uatxgdma *gdma_reg;
+ unsigned int ch;
+
+ if (sp_port->uport.rs485.flags & SER_RS485_ENABLED)
+ hrtimer_cancel(&sp_port->DelayRtsAfterSend);
+
+#ifdef CONFIG_PM_RUNTIME_UART
+ if (port->line > 0) {
+ ret = pm_runtime_get_sync(port->dev);
+ if (ret < 0)
+ goto out;
+ }
+#endif
+
+ ret = request_irq(port->irq, sunplus_uart_irq, 0, sp_port->name, port);
+ if (ret)
+ return ret;
+
+ uartdma_rx = sp_port->uartdma_rx;
+ if (uartdma_rx) {
+ rxdma_reg = (struct regs_uarxdma *)(uartdma_rx->membase);
+
+ if (uartdma_rx->buf_va == NULL) {
+ /* Drop data in Rx FIFO (PIO mode) */
+ while (sp_uart_get_line_status(port->membase) & SP_UART_LSR_RX)
+ ch = sp_uart_get_char(port->membase);
+
+ uartdma_rx->buf_va =
+ dma_alloc_coherent(port->dev, UARXDMA_BUF_SZ,
+ &(uartdma_rx->dma_handle), GFP_KERNEL);
+ if (uartdma_rx->buf_va == NULL) {
+ DBG_ERR("%s, %d, Can't allocation buffer for %s\n",
+ __func__, __LINE__, sp_port->name);
+ ret = -ENOMEM;
+ goto error_01;
+ }
+ DBG_INFO("DMA buffer (Rx) for %s: VA: 0x%p, PA: 0x%x\n",
+ sp_port->name, uartdma_rx->buf_va, (u32)(uartdma_rx->dma_handle));
+
+ writel((u32)(uartdma_rx->dma_handle), &(rxdma_reg->rxdma_start_addr));
+ writel((u32)(uartdma_rx->dma_handle), &(rxdma_reg->rxdma_rd_adr));
+
+ /* Force to use CLK_HIGH_UART in this mode */
+ /* Switch clock source when setting baud rate */
+ timeout = (CLK_HIGH_UART / 2) / 1000000 * 1000; /* 1 msec */
+
+ /* DBG_INFO("timeout: 0x%x\n", timeout); */
+ writel(timeout, &(rxdma_reg->rxdma_timeout_set));
+
+ /*
+ * When there are only rxdma_length_thr[15:0] bytes
+ * of free buffer => Trigger interrupt
+ */
+ writel(((UARXDMA_BUF_SZ << 16) | (UARXDMA_BUF_SZ - MAX_SZ_RXDMA_ISR)),
+ &(rxdma_reg->rxdma_length_thr));
+ writel((readl(&(rxdma_reg->rxdma_enable_sel)) & (~DMA_SEL_UARTX_MASK)),
+ &(rxdma_reg->rxdma_enable_sel));
+ writel((readl(&(rxdma_reg->rxdma_enable_sel))
+ | (DMA_INIT | (uartdma_rx->which_uart << DMA_SEL_UARTX_SHIFT))),
+ &(rxdma_reg->rxdma_enable_sel));
+ writel((readl(&(rxdma_reg->rxdma_enable_sel)) & (~DMA_INIT)),
+ &(rxdma_reg->rxdma_enable_sel));
+ writel((readl(&(rxdma_reg->rxdma_enable_sel))
+ | (DMA_SW_RST_B | DMA_AUTO_ENABLE
+ | DMA_TIMEOUT_INT_EN | DMA_ENABLE)),
+ &(rxdma_reg->rxdma_enable_sel));
+ writel((readl(&(rxdma_reg->rxdma_enable_sel)) | (DMA_GO)),
+ &(rxdma_reg->rxdma_enable_sel));
+ }
+ DBG_INFO("Enable RXDMA for %s (irq=%d)\n", sp_port->name, uartdma_rx->irq);
+ ret = request_irq(uartdma_rx->irq, sunplus_uart_rxdma_irq, 0, "UARTDMA_RX", port);
+ if (ret) {
+ dma_free_coherent(port->dev, UARXDMA_BUF_SZ,
+ uartdma_rx->buf_va, uartdma_rx->dma_handle);
+ goto error_00;
+ }
+ }
+
+ uartdma_tx = sp_port->uartdma_tx;
+ if (uartdma_tx) {
+ txdma_reg = (struct regs_uatxdma *)(uartdma_tx->membase);
+ gdma_reg = (struct regs_uatxgdma *)(uartdma_tx->gdma_membase);
+ DBG_INFO("Enable TXDMA for %s\n", sp_port->name);
+
+ if (uartdma_tx->buf_va == NULL) {
+ uartdma_tx->buf_va =
+ dma_alloc_coherent(port->dev, UATXDMA_BUF_SZ,
+ &(uartdma_tx->dma_handle), GFP_KERNEL);
+ if (uartdma_tx->buf_va == NULL) {
+ DBG_ERR("%s, %d, Can't allocation buffer for %s\n",
+ __func__, __LINE__, sp_port->name);
+ ret = -ENOMEM;
+ goto error_01;
+ }
+ DBG_INFO("DMA buffer (Tx) for %s: VA: 0x%p, PA: 0x%x\n",
+ sp_port->name, uartdma_tx->buf_va, (u32)(uartdma_tx->dma_handle));
+
+ /*
+ * set 1ms , set wr_adr , set start_addr/end_addr ,
+ * set bind to uart# , set int enable ,
+ * set txdma enable (Use ring buffer for UART's Tx)
+ */
+ writel((CLK_HIGH_UART / 1000), &(txdma_reg->txdma_tmr_unit));
+ writel((u32)(uartdma_tx->dma_handle), &(txdma_reg->txdma_wr_adr));
+ writel((u32)(uartdma_tx->dma_handle), &(txdma_reg->txdma_start_addr));
+ writel(((u32)(uartdma_tx->dma_handle) + UATXDMA_BUF_SZ - 1),
+ &(txdma_reg->txdma_end_addr));
+ writel(uartdma_tx->which_uart, &(txdma_reg->txdma_sel));
+ writel(0x41, &(gdma_reg->gdma_int_en));
+ writel(0x00000005, &(txdma_reg->txdma_enable));
+ }
+ }
+
+ /*
+ * don't need to use spin_lock_irqsave() because interrupts
+ * are globally disabled
+ */
+ spin_lock_irq(&port->lock);
+
+ /* SP_UART_ISC_TXM is enabled in .start_tx() */
+ interrupt_en = 0;
+ if (uartdma_rx == NULL)
+ interrupt_en |= SP_UART_ISC_RXM;
+
+ sp_uart_set_int_en(port->membase, interrupt_en);
+
+ spin_unlock_irq(&port->lock);
+
+#ifdef CONFIG_PM_RUNTIME_UART
+ if (port->line > 0)
+ pm_runtime_put(port->dev);
+
+ return 0;
+
+out:
+ if (port->line > 0) {
+ pr_info("pm_out\n");
+ pm_runtime_mark_last_busy(port->dev);
+ pm_runtime_put_autosuspend(port->dev);
+ }
+#endif
+ return 0;
+
+error_01:
+ if (uartdma_rx) {
+ dma_free_coherent(port->dev, UARXDMA_BUF_SZ,
+ uartdma_rx->buf_va, uartdma_rx->dma_handle);
+ free_irq(uartdma_rx->irq, port);
+ }
+error_00:
+ free_irq(port->irq, port);
+ return ret;
+}
+
+static void sunplus_uart_ops_shutdown(struct uart_port *port)
+{
+ unsigned long flags;
+ struct sunplus_uart_port *sp_port =
+ (struct sunplus_uart_port *)(port->private_data);
+ struct sunplus_uartdma_info *uartdma_rx;
+ struct regs_uarxdma *rxdma_reg;
+
+ spin_lock_irqsave(&port->lock, flags);
+ sp_uart_set_int_en(port->membase, 0);
+ spin_unlock_irqrestore(&port->lock, flags);
+
+ free_irq(port->irq, port);
+
+ uartdma_rx = sp_port->uartdma_rx;
+ if (uartdma_rx) {
+ rxdma_reg = (struct regs_uarxdma *)(uartdma_rx->membase);
+
+ /* Drop whatever is still in buffer */
+ writel(readl(&(rxdma_reg->rxdma_wr_adr)), &(rxdma_reg->rxdma_rd_adr));
+
+ free_irq(uartdma_rx->irq, port);
+ DBG_INFO("free_irq(%d)\n", uartdma_rx->irq);
+ }
+
+ /* Disable flow control of Tx, so that queued data can be sent out
+ * There is no way for s/w to let h/w abort in the middle of
+ * transaction.
+ * Don't reset module except it's in idle state. Otherwise, it might
+ * cause bus to hang.
+ */
+ sp_uart_set_modem_ctrl(port->membase,
+ sp_uart_get_modem_ctrl(port->membase) & (~(SP_UART_MCR_AC)));
+
+}
+
+static void sunplus_uart_ops_set_termios(struct uart_port *port,
+ struct ktermios *termios, struct ktermios *oldtermios)
+{
+ u32 clk, ext, div, div_l, div_h, baud;
+ u32 lcr;
+ unsigned long flags;
+
+ baud = uart_get_baud_rate(port, termios, oldtermios, 0, (CLK_HIGH_UART >> 4));
+
+ clk = port->uartclk;
+
+ /*
+ * Send all data in Tx FIFO before changing clock source,
+ * it should be UART0 only
+ */
+ while (!(sp_uart_get_line_status(port->membase) & SP_UART_LSR_TXE))
+ ;
+
+ /* Switch clock source: 0 for sysclk, 1 for XTAL */
+ sp_uart_set_clk_src(port->membase, clk == XTAL);
+
+ clk += baud >> 1;
+ div = clk / baud;
+ ext = div & 0x0F;
+ div = (div >> 4) - 1;
+ div_l = (div & 0xFF) | (ext << 12);
+ div_h = div >> 8;
+
+ switch (termios->c_cflag & CSIZE) {
+ case CS5:
+ lcr = SP_UART_LCR_WL5;
+ break;
+ case CS6:
+ lcr = SP_UART_LCR_WL6;
+ break;
+ case CS7:
+ lcr = SP_UART_LCR_WL7;
+ break;
+ default: /* CS8 */
+ lcr = SP_UART_LCR_WL8;
+ break;
+ }
+
+ if (termios->c_cflag & CSTOPB)
+ lcr |= SP_UART_LCR_ST;
+
+ if (termios->c_cflag & PARENB) {
+ lcr |= SP_UART_LCR_PE;
+
+ if (!(termios->c_cflag & PARODD))
+ lcr |= SP_UART_LCR_PR;
+ }
+
+ spin_lock_irqsave(&port->lock, flags);
+
+ uart_update_timeout(port, termios->c_cflag, baud);
+
+ port->read_status_mask = 0;
+ if (termios->c_iflag & INPCK)
+ port->read_status_mask |= SP_UART_LSR_PE | SP_UART_LSR_FE;
+
+ if (termios->c_iflag & (BRKINT | PARMRK))
+ port->read_status_mask |= SP_UART_LSR_BC;
+
+ /*
+ * Characters to ignore
+ */
+ port->ignore_status_mask = 0;
+ if (termios->c_iflag & IGNPAR)
+ port->ignore_status_mask |= SP_UART_LSR_FE | SP_UART_LSR_PE;
+
+ if (termios->c_iflag & IGNBRK) {
+ port->ignore_status_mask |= SP_UART_LSR_BC;
+
+ if (termios->c_iflag & IGNPAR)
+ port->ignore_status_mask |= SP_UART_LSR_OE;
+ }
+
+ /*
+ * Ignore all characters if CREAD is not set.
+ */
+ if ((termios->c_cflag & CREAD) == 0) {
+ port->ignore_status_mask |= SP_UART_CREAD_DISABLED;
+ /* flush rx data FIFO */
+ sp_uart_set_rx_residue(port->membase, 0);
+ }
+
+ if (termios->c_cflag & CRTSCTS) {
+ sp_uart_set_modem_ctrl(port->membase,
+ sp_uart_get_modem_ctrl(port->membase)
+ | (SP_UART_MCR_AC | SP_UART_MCR_AR));
+ } else {
+ sp_uart_set_modem_ctrl(port->membase,
+ sp_uart_get_modem_ctrl(port->membase)
+ & (~(SP_UART_MCR_AC | SP_UART_MCR_AR)));
+ }
+
+ /* do not set these in emulation */
+ sp_uart_set_divider_high_register(port->membase, div_h);
+ sp_uart_set_divider_low_register(port->membase, div_l);
+ sp_uart_set_line_ctrl(port->membase, lcr);
+
+ spin_unlock_irqrestore(&port->lock, flags);
+}
+
+static void sunplus_uart_ops_set_ldisc(struct uart_port *port,
+ struct ktermios *termios)
+{
+ int new = termios->c_line;
+
+ if (new == N_PPS) {
+ port->flags |= UPF_HARDPPS_CD;
+ sunplus_uart_ops_enable_ms(port);
+ } else {
+ port->flags &= ~UPF_HARDPPS_CD;
+ }
+}
+
+static const char *sunplus_uart_ops_type(struct uart_port *port)
+{
+ struct sunplus_uart_port *sunplus_uart_port =
+ (struct sunplus_uart_port *)port->private_data;
+ return sunplus_uart_port->name;
+}
+
+static void sunplus_uart_ops_release_port(struct uart_port *port)
+{
+}
+
+static int sunplus_uart_ops_request_port(struct uart_port *port)
+{
+ return 0;
+}
+
+static void sunplus_uart_ops_config_port(struct uart_port *port, int type)
+{
+ if (type & UART_CONFIG_TYPE) {
+ port->type = PORT_SUNPLUS;
+ sunplus_uart_ops_request_port(port);
+ }
+}
+
+static int sunplus_uart_ops_verify_port(struct uart_port *port, struct serial_struct *serial)
+{
+ return -EINVAL;
+}
+
+#ifdef CONFIG_CONSOLE_POLL
+static int sunplus_uart_ops_poll_init(struct uart_port *port)
+{
+ return 0;
+}
+
+static void sunplus_uart_ops_poll_put_char(struct uart_port *port,
+ unsigned char data)
+{
+ wait_for_xmitr(port);
+ sp_uart_put_char(port, data);
+}
+
+static int sunplus_uart_ops_poll_get_char(struct uart_port *port)
+{
+ unsigned int status;
+ unsigned char data;
+
+ do {
+ status = sp_uart_get_line_status(port->membase);
+ } while (!(status & SP_UART_LSR_RX));
+
+ data = sp_uart_get_char(port->membase);
+ return (int)data;
+}
+#endif /* CONFIG_CONSOLE_POLL */
+
+static enum hrtimer_restart Check_TXE(struct hrtimer *t)
+{
+ unsigned char lsr;
+ struct sunplus_uart_port *rs485;
+ unsigned char mcr, val;
+ ktime_t ktime;
+ unsigned long nsec;
+
+ rs485 = container_of(t, struct sunplus_uart_port, CheckTXE);
+ mcr = sp_uart_get_modem_ctrl(rs485->uport.membase);
+ lsr = sp_uart_get_line_status(rs485->uport.membase);
+ // TX is NOT empty
+ if (!(lsr & SP_UART_LSR_TXE))
+ return HRTIMER_RESTART;
+ // TX is empty
+ nsec = rs485->uport.rs485.delay_rts_after_send * 1000000;
+ // schedule RTS set
+ if (nsec > 0) {
+ ktime = ktime_set(0, nsec);
+ hrtimer_start(&rs485->DelayRtsAfterSend, ktime, HRTIMER_MODE_REL);
+ return HRTIMER_NORESTART;
+ }
+ // immediately set RTS
+ val = (rs485->uport.rs485.flags & SER_RS485_RTS_AFTER_SEND ? 1 : 0);
+ if (rs485->uport.rs485.flags & SER_RS485_RTS_ON_SEND)
+ mcr |= SP_UART_MCR_RTS;
+ else
+ mcr &= ~SP_UART_MCR_RTS;
+ if (rs485->uport.rs485.flags & SER_RS485_ENABLED && !IS_ERR(rs485->rts_gpio)) {
+ gpiod_set_value(rs485->rts_gpio, val);
+ dev_dbg(rs485->uport.dev, "%s set rts_gpio=%d\n",
+ rs485->uport.name, val);
+ } else {
+ sp_uart_set_modem_ctrl(rs485->uport.membase, mcr);
+ }
+ return HRTIMER_NORESTART;
+}
+
+static enum hrtimer_restart Delay_Rts_Before_Send(struct hrtimer *t)
+{
+ struct sunplus_uart_port *rs485;
+ ktime_t ktime;
+
+ rs485 = container_of(t, struct sunplus_uart_port, DelayRtsBeforeSend);
+ ktime = ktime_set(0, 500000); //500us
+ hrtimer_start(&rs485->CheckTXE, ktime, HRTIMER_MODE_REL);
+ __start_tx(&rs485->uport);
+ return HRTIMER_NORESTART;
+}
+
+static enum hrtimer_restart Delay_Rts_After_Send(struct hrtimer *t)
+{
+ struct sunplus_uart_port *rs485;
+ unsigned char mcr, val;
+
+ rs485 = container_of(t, struct sunplus_uart_port, DelayRtsAfterSend);
+ mcr = sp_uart_get_modem_ctrl(rs485->uport.membase);
+
+ val = (rs485->uport.rs485.flags & SER_RS485_RTS_AFTER_SEND ? 1 : 0);
+ if (rs485->uport.rs485.flags & SER_RS485_RTS_ON_SEND)
+ mcr |= SP_UART_MCR_RTS;
+ else
+ mcr &= ~SP_UART_MCR_RTS;
+ if (rs485->uport.rs485.flags & SER_RS485_ENABLED && !IS_ERR(rs485->rts_gpio)) {
+ gpiod_set_value(rs485->rts_gpio, val);
+ dev_dbg(rs485->uport.dev, "%s set rts_gpio=%d\n",
+ rs485->uport.name, val);
+ } else {
+ sp_uart_set_modem_ctrl(rs485->uport.membase, mcr);
+ }
+ return HRTIMER_NORESTART;
+}
+
+static int sunplus_uart_rs485_onn(struct uart_port *_up,
+ struct sunplus_uart_port *_sup)
+{
+ if (IS_ERR(_sup->rts_gpio)) {
+ DBG_ERR("%s %s No valid rts_gpio, disabling 485\n",
+ _up->name, __func__);
+ _up->rs485.flags &= ~SER_RS485_ENABLED;
+ return (-EINVAL);
+ }
+ DBG_INFO("%s %s rts_gpio is at G_MX[%d].\n",
+ _up->name, __func__, desc_to_gpio(_sup->rts_gpio));
+ if (!_sup->CheckTXE.function) {
+ hrtimer_init(&(_sup->CheckTXE), CLOCK_MONOTONIC, HRTIMER_MODE_REL);
+ _sup->CheckTXE.function = Check_TXE;
+ }
+ if (!_sup->DelayRtsBeforeSend.function) {
+ hrtimer_init(&(_sup->DelayRtsBeforeSend), CLOCK_MONOTONIC, HRTIMER_MODE_REL);
+ _sup->DelayRtsBeforeSend.function = Delay_Rts_Before_Send;
+ }
+ if (!_sup->DelayRtsAfterSend.function) {
+ hrtimer_init(&(_sup->DelayRtsAfterSend), CLOCK_MONOTONIC, HRTIMER_MODE_REL);
+ _sup->DelayRtsAfterSend.function = Delay_Rts_After_Send;
+ }
+ return (0);
+}
+
+static int sunplus_uart_rs485_off(struct uart_port *_up,
+ struct sunplus_uart_port *_sup)
+{
+ _up->rs485.flags &= ~SER_RS485_ENABLED;
+ if (_sup->CheckTXE.function) {
+ hrtimer_cancel(&_sup->CheckTXE);
+ _sup->CheckTXE.function = NULL;
+ }
+ if (_sup->DelayRtsBeforeSend.function) {
+ hrtimer_cancel(&_sup->DelayRtsBeforeSend);
+ _sup->DelayRtsBeforeSend.function = NULL;
+ }
+ if (_sup->DelayRtsAfterSend.function) {
+ hrtimer_cancel(&_sup->DelayRtsAfterSend);
+ _sup->DelayRtsAfterSend.function = NULL;
+ }
+ return (0);
+}
+
+static int sunplus_uart_config_rs485(struct uart_port *_up,
+ struct serial_rs485 *_rs485)
+{
+ struct sunplus_uart_port *_sup =
+ (struct sunplus_uart_port *)_up->private_data;
+ int val;
+
+ if (IS_ERR(_sup->rts_gpio)) {
+ DBG_ERR("%s %s No valid rts_gpio - skipping rs485\n",
+ _up->name, __func__);
+ _up->rs485.flags &= ~SER_RS485_ENABLED;
+ return (-EINVAL);
+ }
+
+#ifdef CONFIG_PM_RUNTIME_UART
+ pm_runtime_get_sync(_sup->dev);
+#endif
+
+ _rs485->delay_rts_before_send =
+ min(_rs485->delay_rts_before_send, 10000U);
+ _rs485->delay_rts_after_send =
+ min(_rs485->delay_rts_after_send, 10000U);
+
+ if (_rs485->flags & SER_RS485_ENABLED) {
+ dev_dbg(_up->dev, "%s enabling rs485...\n", _up->name);
+ dev_dbg(_up->dev, "%s on_ send:%d (delay:%d)\n",
+ _up->name, _rs485->flags & SER_RS485_RTS_ON_SEND,
+ _rs485->delay_rts_before_send);
+ dev_dbg(_up->dev, "%s after_ send:%d (delay:%d)\n",
+ _up->name, _rs485->flags & SER_RS485_RTS_AFTER_SEND,
+ _rs485->delay_rts_after_send);
+ sunplus_uart_rs485_onn(_up, _sup);
+ val = (_rs485->flags & SER_RS485_RTS_AFTER_SEND ? 1 : 0);
+ gpiod_set_value(_sup->rts_gpio, val);
+ dev_dbg(_up->dev, "%s set rts_gpio=%d\n", _up->name, val);
+ } else {
+ dev_dbg(_up->dev, "%s disabling rs485...\n", _up->name);
+ sunplus_uart_rs485_off(_up, _sup);
+ }
+ _up->rs485 = *_rs485;
+
+#ifdef CONFIG_PM_RUNTIME_UART
+ pm_runtime_mark_last_busy(_sup->dev);
+ pm_runtime_put_autosuspend(_sup->dev);
+#endif
+ return (0);
+}
+
+static const struct uart_ops sunplus_uart_ops = {
+ .tx_empty = sunplus_uart_ops_tx_empty,
+ .set_mctrl = sunplus_uart_ops_set_mctrl,
+ .get_mctrl = sunplus_uart_ops_get_mctrl,
+ .stop_tx = sunplus_uart_ops_stop_tx,
+ .start_tx = sunplus_uart_ops_start_tx,
+ .stop_rx = sunplus_uart_ops_stop_rx,
+ .enable_ms = sunplus_uart_ops_enable_ms,
+ .break_ctl = sunplus_uart_ops_break_ctl,
+ .startup = sunplus_uart_ops_startup,
+ .shutdown = sunplus_uart_ops_shutdown,
+ .set_termios = sunplus_uart_ops_set_termios,
+ .set_ldisc = sunplus_uart_ops_set_ldisc,
+ .type = sunplus_uart_ops_type,
+ .release_port = sunplus_uart_ops_release_port,
+ .request_port = sunplus_uart_ops_request_port,
+ .config_port = sunplus_uart_ops_config_port,
+ .verify_port = sunplus_uart_ops_verify_port,
+#ifdef CONFIG_CONSOLE_POLL
+ .poll_init = sunplus_uart_ops_poll_init,
+ .poll_put_char = sunplus_uart_ops_poll_put_char,
+ .poll_get_char = sunplus_uart_ops_poll_get_char,
+#endif /* CONFIG_CONSOLE_POLL */
+};
+
+static struct uart_driver sunplus_uart_driver;
+
+#ifdef CONFIG_SERIAL_SUNPLUS_CONSOLE
+static void sunplus_uart_console_putchar(struct uart_port *port, int ch)
+{
+ wait_for_xmitr(port);
+ sp_uart_put_char(port, ch);
+}
+
+static void sunplus_console_write(struct console *co,
+ const char *s, unsigned int count)
+{
+ unsigned long flags;
+ int locked = 1;
+ struct sunplus_uart_port *sp_port;
+ struct sunplus_uartdma_info *uartdma_tx;
+ struct regs_uatxdma *txdma_reg;
+ struct regs_uatxgdma *gdma_reg;
+
+ local_irq_save(flags);
+
+#if defined(SUPPORT_SYSRQ)
+ if (sunplus_uart_ports[co->index].uport.sysrq)
+#else
+ if (0)
+#endif
+ {
+ locked = 0;
+ } else if (oops_in_progress) {
+ locked = spin_trylock(&sunplus_uart_ports[co->index].uport.lock);
+ } else {
+ spin_lock(&sunplus_uart_ports[co->index].uport.lock);
+ }
+
+ sp_port = (struct sunplus_uart_port *)(sunplus_uart_ports[co->index].uport.private_data);
+ uartdma_tx = sp_port->uartdma_tx;
+ if (uartdma_tx) {
+ txdma_reg = (struct regs_uatxdma *)(uartdma_tx->membase);
+ gdma_reg = (struct regs_uatxgdma *)(uartdma_tx->gdma_membase);
+ if (readl(&(txdma_reg->txdma_enable)) == 0x00000005) {
+ /* ring buffer for UART's Tx has been enabled */
+ uart_console_write(&sunplus_uart_ports[co->index].uport,
+ s, count, sunplus_uart_console_putchar);
+ } else {
+ /* Refer to .startup() */
+ if (uartdma_tx->buf_va == NULL) {
+ uartdma_tx->buf_va =
+ dma_alloc_coherent(sunplus_uart_ports[co->index].uport.dev,
+ UATXDMA_BUF_SZ, &(uartdma_tx->dma_handle), GFP_KERNEL);
+ /*
+ * This message can't be sent to console
+ * because it's not ready yet
+ */
+ if (uartdma_tx->buf_va == NULL)
+ panic("Die here.");
+
+ /*
+ * set 1ms , set wr_adr , set start_addr/end_addr ,
+ * set bind to uart# , set int enable ,
+ * set txdma enable (Use ring buffer for UART's Tx)
+ */
+ writel((CLK_HIGH_UART / 1000),
+ &(txdma_reg->txdma_tmr_unit));
+ writel((u32)(uartdma_tx->dma_handle),
+ &(txdma_reg->txdma_wr_adr));
+ writel((u32)(uartdma_tx->dma_handle),
+ &(txdma_reg->txdma_start_addr));
+ writel(((u32)(uartdma_tx->dma_handle) + UATXDMA_BUF_SZ - 1),
+ &(txdma_reg->txdma_end_addr));
+ writel(uartdma_tx->which_uart,
+ &(txdma_reg->txdma_sel));
+ writel(0x41, &(gdma_reg->gdma_int_en));
+ writel(0x00000005, &(txdma_reg->txdma_enable));
+ }
+ }
+ } else {
+ uart_console_write(&sunplus_uart_ports[co->index].uport,
+ s, count, sunplus_uart_console_putchar);
+ }
+
+ if (locked)
+ spin_unlock(&sunplus_uart_ports[co->index].uport.lock);
+
+ local_irq_restore(flags);
+}
+
+static int __init sunplus_console_setup(struct console *co, char *options)
+{
+ int ret = 0;
+ int baud = 115200;
+ int bits = 8;
+ int parity = 'n';
+ int flow = 'n';
+
+ if ((co->index >= NUM_UART) || (co->index < 0))
+ return -EINVAL;
+
+ if (options)
+ uart_parse_options(options, &baud, &parity, &bits, &flow);
+
+ ret = uart_set_options(&sunplus_uart_ports[co->index].uport,
+ co, baud, parity, bits, flow);
+
+ return ret;
+}
+
+static struct console sunplus_console = {
+ .name = DEVICE_NAME,
+ .write = sunplus_console_write,
+ .device = uart_console_device, /* default */
+ .setup = sunplus_console_setup,
+ /*
+ * CON_ENABLED,
+ * CON_CONSDEV: preferred console,
+ * CON_BOOT: primary boot console,
+ * CON_PRINTBUFFER: used for printk buffer
+ */
+ .flags = CON_PRINTBUFFER,
+ .index = -1,
+ .data = &sunplus_uart_driver
+};
+#endif
+
+static struct uart_driver sunplus_uart_driver = {
+ .owner = THIS_MODULE,
+ .driver_name = "Sunplus_UART",
+ .dev_name = DEVICE_NAME,
+ .major = SP_UART_MAJOR,
+ .minor = SP_UART_MINOR_START,
+ .nr = NUM_UART,
+#ifdef CONFIG_SERIAL_SUNPLUS_CONSOLE
+ .cons = &sunplus_console
+#endif
+};
+
+struct platform_device *sunpluse_uart_platform_device;
+
+static int sunplus_uart_platform_driver_probe_of(struct platform_device *pdev)
+{
+ struct resource *res_mem;
+ struct uart_port *port;
+ struct clk *clk;
+ int ret, irq;
+ int idx_offset, idx;
+ int idx_which_uart;
+ char peri_name[16];
+#ifdef TTYS_GPIO
+ int uart_gpio;
+#endif
+
+ if (pdev->dev.of_node) {
+ pdev->id = of_alias_get_id(pdev->dev.of_node, "serial");
+ if (pdev->id < 0)
+ pdev->id = of_alias_get_id(pdev->dev.of_node, "uart");
+ }
+
+ DBG_INFO("sunplus_uart-ID = %d\n", pdev->id);
+
+ idx_offset = -1;
+ if (IS_UARTDMARX_ID(pdev->id)) {
+ idx_offset = 0;
+ DBG_INFO("Setup DMA Rx %d\n", (pdev->id - ID_BASE_DMARX));
+ } else if (IS_UARTDMATX_ID(pdev->id)) {
+ idx_offset = NUM_UARTDMARX;
+ DBG_INFO("Setup DMA Tx %d\n", (pdev->id - ID_BASE_DMATX));
+ }
+ if (idx_offset >= 0) {
+ DBG_INFO("Enable DMA clock(s)\n");
+ clk = devm_clk_get(&pdev->dev, NULL);
+ if (IS_ERR(clk)) {
+ DBG_ERR("Can't find clock source\n");
+ return PTR_ERR(clk);
+ }
+
+ ret = clk_prepare_enable(clk);
+ if (ret) {
+ DBG_ERR("Clock can't be enabled correctly\n");
+ return ret;
+ }
+
+ if (idx_offset == 0)
+ idx = idx_offset + pdev->id - ID_BASE_DMARX;
+ else
+ idx = idx_offset + pdev->id - ID_BASE_DMATX;
+
+ res_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!res_mem)
+ return -ENODEV;
+
+ sprintf(peri_name, "PERI%d", (idx & 0x01));
+ DBG_INFO("Enable clock %s\n", peri_name);
+ clk = devm_clk_get(&pdev->dev, peri_name);
+ if (IS_ERR(clk)) {
+ DBG_ERR("Can't find clock source: %s\n", peri_name);
+ return PTR_ERR(clk);
+ }
+
+ ret = clk_prepare_enable(clk);
+ if (ret) {
+ DBG_ERR("%s can't be enabled correctly\n", peri_name);
+ return ret;
+ }
+
+ sunplus_uartdma[idx].addr_phy =
+ (unsigned long)(res_mem->start);
+ sunplus_uartdma[idx].membase =
+ devm_ioremap_resource(&pdev->dev, res_mem);
+
+ if (IS_ERR(sunplus_uartdma[idx].membase))
+ return PTR_ERR(sunplus_uartdma[idx].membase);
+
+ if (IS_UARTDMARX_ID(pdev->id)) {
+ irq = platform_get_irq(pdev, 0);
+ if (irq < 0)
+ return -ENODEV;
+
+ sunplus_uartdma[idx].irq = irq;
+ } else {
+ res_mem = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+ if (!res_mem)
+ return -ENODEV;
+
+ sunplus_uartdma[idx].gdma_membase =
+ devm_ioremap_resource(&pdev->dev, res_mem);
+
+ if (IS_ERR(sunplus_uartdma[idx].gdma_membase))
+ return -EINVAL;
+
+ DBG_INFO("gdma_phy: 0x%x gdma_membase: 0x%p\n",
+ res_mem->start,
+ sunplus_uartdma[idx].gdma_membase);
+ }
+
+ if (of_property_read_u32(pdev->dev.of_node, "which-uart", &idx_which_uart) != 0) {
+ DBG_ERR("\"which-uart\" is not assigned.");
+ return -EINVAL;
+ }
+ if (idx_which_uart >= NUM_UART) {
+ DBG_ERR("\"which-uart\" is not valid.");
+ return -EINVAL;
+ }
+ sunplus_uartdma[idx].which_uart = idx_which_uart;
+
+ DBG_INFO("adr: 0x%lx, base: 0x%p, irq: %d, uart: %d\n",
+ sunplus_uartdma[idx].addr_phy,
+ sunplus_uartdma[idx].membase,
+ sunplus_uartdma[idx].irq,
+ sunplus_uartdma[idx].which_uart);
+
+ return 0;
+ } else if (pdev->id < 0 || pdev->id >= NUM_UART) {
+ return -EINVAL;
+ }
+
+ port = &sunplus_uart_ports[pdev->id].uport;
+ if (port->membase)
+ return -EBUSY;
+
+ memset(port, 0, sizeof(*port));
+
+ res_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!res_mem)
+ return -ENODEV;
+
+ port->dev = &pdev->dev;
+ port->mapbase = res_mem->start;
+ port->membase = devm_ioremap_resource(&pdev->dev, res_mem);
+ if (IS_ERR(port->membase))
+ return PTR_ERR(port->membase);
+
+ irq = platform_get_irq(pdev, 0);
+ if (irq < 0)
+ return -ENODEV;
+
+ uart_get_rs485_mode(port);
+ sunplus_uart_ports[pdev->id].rts_gpio =
+ devm_gpiod_get(&pdev->dev, "rts", GPIOD_OUT_LOW);
+ port->rs485_config = sunplus_uart_config_rs485;
+ sunplus_uart_ports[pdev->id].CheckTXE.function = NULL;
+ sunplus_uart_ports[pdev->id].DelayRtsBeforeSend.function = NULL;
+ sunplus_uart_ports[pdev->id].DelayRtsAfterSend.function = NULL;
+ if (port->rs485.flags & SER_RS485_ENABLED)
+ sunplus_uart_rs485_onn(port, &(sunplus_uart_ports[pdev->id]));
+
+ DBG_INFO("Enable UART clock(s)\n");
+ sunplus_uart_ports[pdev->id].clk = devm_clk_get(&pdev->dev, NULL);
+ if (IS_ERR(sunplus_uart_ports[pdev->id].clk)) {
+ DBG_ERR("Can't find clock source\n");
+ return PTR_ERR(sunplus_uart_ports[pdev->id].clk);
+ }
+
+ ret = clk_prepare_enable(sunplus_uart_ports[pdev->id].clk);
+ if (ret) {
+ DBG_ERR("Clock can't be enabled correctly\n");
+ return ret;
+ }
+
+ sunplus_uart_ports[pdev->id].rstc =
+ devm_reset_control_get(&pdev->dev, NULL);
+
+ if (IS_ERR(sunplus_uart_ports[pdev->id].rstc)) {
+ DBG_ERR("failed to retrieve reset controller: %d\n", ret);
+ return PTR_ERR(sunplus_uart_ports[pdev->id].rstc);
+ }
+
+ ret = reset_control_deassert(sunplus_uart_ports[pdev->id].rstc);
+
+ if (ret) {
+ DBG_ERR("failed to deassert reset line: %d\n", ret);
+ return ret;
+ }
+
+ clk = sunplus_uart_ports[pdev->id].clk;
+ if (IS_ERR(clk))
+ port->uartclk = XTAL;
+ else
+ port->uartclk = clk_get_rate(clk);
+
+ port->iotype = UPIO_MEM;
+ port->irq = irq;
+ port->ops = &sunplus_uart_ops;
+ port->flags = UPF_BOOT_AUTOCONF;
+ port->fifosize = 128;
+ port->line = pdev->id;
+
+#ifdef CONFIG_SERIAL_SUNPLUS_CONSOLE
+ if (pdev->id == 0)
+ port->cons = &sunplus_console;
+#endif
+#ifdef TTYS_GPIO
+ if (pdev->id == 1) {
+ uart_gpio = of_get_named_gpio(pdev->dev.of_node,
+ "uart-gpio", 0);
+ if (!gpio_is_valid(uart_gpio))
+ pr_info("gpio get error\n");
+ else
+ pr_info("gpio no. %d\n", uart_gpio);
+ }
+#endif
+ port->private_data = container_of(&sunplus_uart_ports[pdev->id].uport,
+ struct sunplus_uart_port, uport);
+ sprintf(sunplus_uart_ports[pdev->id].name, "sp_uart%d", pdev->id);
+
+ sunplus_uart_ports[pdev->id].uartdma_rx =
+ sunplus_uartdma_rx_binding(pdev->id);
+
+ if (sunplus_uart_ports[pdev->id].uartdma_rx)
+ DBG_ERR("%s's Rx is in DMA mode.\n",
+ sunplus_uart_ports[pdev->id].name);
+ else
+ DBG_ERR("%s's Rx is in PIO mode.\n",
+ sunplus_uart_ports[pdev->id].name);
+
+ sunplus_uart_ports[pdev->id].uartdma_tx =
+ sunplus_uartdma_tx_binding(pdev->id);
+
+ if (sunplus_uart_ports[pdev->id].uartdma_tx)
+ DBG_ERR("%s's Tx is in DMA mode.\n",
+ sunplus_uart_ports[pdev->id].name);
+ else
+ DBG_ERR("%s's Tx is in PIO mode.\n",
+ sunplus_uart_ports[pdev->id].name);
+
+ ret = uart_add_one_port(&sunplus_uart_driver, port);
+ if (ret) {
+ port->membase = NULL;
+ return ret;
+ }
+ platform_set_drvdata(pdev, port);
+
+#ifdef CONFIG_PM_RUNTIME_UART
+ if (pdev->id != 0) {
+ pm_runtime_set_autosuspend_delay(&pdev->dev, 5000);
+ pm_runtime_use_autosuspend(&pdev->dev);
+ pm_runtime_set_active(&pdev->dev);
+ pm_runtime_enable(&pdev->dev);
+ }
+#endif
+ return 0;
+}
+
+static int sunplus_uart_platform_driver_remove(struct platform_device *pdev)
+{
+#ifdef CONFIG_PM_RUNTIME_UART
+ if (pdev->id != 0) {
+ pm_runtime_disable(&pdev->dev);
+ pm_runtime_set_suspended(&pdev->dev);
+ }
+#endif
+ uart_remove_one_port(&sunplus_uart_driver,
+ &sunplus_uart_ports[pdev->id].uport);
+
+ if (pdev->id < NUM_UART) {
+ clk_disable_unprepare(sunplus_uart_ports[pdev->id].clk);
+ reset_control_assert(sunplus_uart_ports[pdev->id].rstc);
+ }
+
+ return 0;
+}
+
+static int sunplus_uart_platform_driver_suspend(struct platform_device *pdev,
+ pm_message_t state)
+{
+ /* Don't suspend uart0 for cmd line usage */
+ if ((pdev->id < NUM_UART) && (pdev->id > 0))
+ reset_control_assert(sunplus_uart_ports[pdev->id].rstc);
+
+ return 0;
+}
+
+static int sunplus_uart_platform_driver_resume(struct platform_device *pdev)
+{
+ if (pdev->id < NUM_UART) {
+ clk_prepare_enable(sunplus_uart_ports[pdev->id].clk);
+ reset_control_deassert(sunplus_uart_ports[pdev->id].rstc);
+ }
+ return 0;
+}
+
+static const struct of_device_id sp_uart_of_match[] = {
+ { .compatible = "sunplus,sp7021-uart" },
+ {}
+};
+MODULE_DEVICE_TABLE(of, sp_uart_of_match);
+
+#ifdef CONFIG_PM_RUNTIME_UART
+static int sunplus_uart_runtime_suspend(struct device *dev)
+{
+ struct platform_device *uartpdev = to_platform_device(dev);
+
+ /* Don't suspend uart0 for cmd line usage */
+ if ((uartpdev->id < NUM_UART) && (uartpdev->id > 0))
+ reset_control_assert(sunplus_uart_ports[uartpdev->id].rstc);
+
+ return 0;
+}
+
+static int sunplus_uart_runtime_resume(struct device *dev)
+{
+ struct platform_device *uartpdev = to_platform_device(dev);
+
+ if (uartpdev->id < NUM_UART) {
+ clk_prepare_enable(sunplus_uart_ports[uartpdev->id].clk);
+ reset_control_deassert(sunplus_uart_ports[uartpdev->id].rstc);
+ }
+
+ return 0;
+}
+static const struct dev_pm_ops sp7021_uart_pm_ops = {
+ .runtime_suspend = sunplus_uart_runtime_suspend,
+ .runtime_resume = sunplus_uart_runtime_resume,
+};
+#define sunplus_uart_pm_ops (&sp7021_uart_pm_ops)
+#endif
+
+static struct platform_driver sunplus_uart_platform_driver = {
+ .probe = sunplus_uart_platform_driver_probe_of,
+ .remove = sunplus_uart_platform_driver_remove,
+ .suspend = sunplus_uart_platform_driver_suspend,
+ .resume = sunplus_uart_platform_driver_resume,
+ .driver = {
+ .name = DEVICE_NAME,
+ .owner = THIS_MODULE,
+ .of_match_table = of_match_ptr(sp_uart_of_match),
+#ifdef CONFIG_PM_RUNTIME_UART
+ .pm = sunplus_uart_pm_ops,
+#endif
+ }
+};
+
+static int __init sunplus_uart_init(void)
+{
+ int ret;
+
+ memset(sunplus_uart_ports, 0, sizeof(sunplus_uart_ports));
+ memset(sunplus_uartdma, 0, sizeof(sunplus_uartdma));
+
+ if (!uart0_as_console || !(uart_enable_status & 0x01))
+ sunplus_uart_driver.cons = NULL;
+
+ /* /proc/tty/driver/(sunplus_uart_driver->driver_name) */
+ ret = uart_register_driver(&sunplus_uart_driver);
+ if (ret < 0)
+ return ret;
+
+ ret = platform_driver_register(&sunplus_uart_platform_driver);
+ if (ret != 0) {
+ uart_unregister_driver(&sunplus_uart_driver);
+ return ret;
+ }
+
+ return 0;
+}
+module_init(sunplus_uart_init);
+
+module_param(uart0_as_console, uint, 0444);
+
+#ifdef CONFIG_SERIAL_EARLYCON
+static void sunplus_uart_putc(struct uart_port *port, int c)
+{
+ unsigned int status;
+
+ for (;;) {
+ status = readl(port->membase + SP_UART_LSR);
+ if ((status & SP_UART_LSR_TXE) == SP_UART_LSR_TXE)
+ break;
+ cpu_relax();
+ }
+ writel(c, port->membase + SP_UART_DATA);
+}
+
+static void sunplus_uart_early_write(struct console *con,
+ const char *s, unsigned int n)
+{
+ struct earlycon_device *dev = con->data;
+
+ uart_console_write(&dev->port, s, n, sunplus_uart_putc);
+}
+
+int __init sunplus_uart_early_setup(struct earlycon_device *device,
+ const char *opt)
+{
+ if (!(device->port.membase || device->port.iobase))
+ return -ENODEV;
+
+ device->con->write = sunplus_uart_early_write;
+ return 0;
+}
+OF_EARLYCON_DECLARE(sunplus_uart, "sunplus,sp7021-uart", sunplus_uart_early_setup);
+#endif
+
+MODULE_DESCRIPTION("Sunplus UART driver");
+MODULE_AUTHOR("Hammer Hsieh <hammer.hsieh@sunplus.com>");
+MODULE_LICENSE("GPL v2");
diff --git a/include/soc/sunplus/sp_uart.h b/include/soc/sunplus/sp_uart.h
new file mode 100644
index 0000000..d8a455c
--- /dev/null
+++ b/include/soc/sunplus/sp_uart.h
@@ -0,0 +1,158 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Sunplus SoC UART driver header file
+ */
+
+#ifndef __SP_UART_H__
+#define __SP_UART_H__
+
+#ifdef CONFIG_DEBUG_SP_UART
+#include <mach/io_map.h>
+
+#define LL_UART_PADDR PA_IOB_ADDR(18 * 32 * 4)
+#define LL_UART_VADDR VA_IOB_ADDR(18 * 32 * 4)
+#define LOGI_ADDR_UART0_REG VA_IOB_ADDR(18 * 32 * 4)
+#endif
+
+/* uart register map */
+#define SP_UART_DATA 0x00
+#define SP_UART_LSR 0x04
+#define SP_UART_MSR 0x08
+#define SP_UART_LCR 0x0C
+#define SP_UART_MCR 0x10
+#define SP_UART_DIV_L 0x14
+#define SP_UART_DIV_H 0x18
+#define SP_UART_ISC 0x1C
+
+/* lsr
+ * 1: trasmit fifo is empty
+ */
+#define SP_UART_LSR_TXE (1 << 6)
+
+/* interrupt
+ * SP_UART_LSR_BC : break condition
+ * SP_UART_LSR_FE : frame error
+ * SP_UART_LSR_OE : overrun error
+ * SP_UART_LSR_PE : parity error
+ * SP_UART_LSR_RX : 1: receive fifo not empty
+ * SP_UART_LSR_TX : 1: transmit fifo is not full
+ */
+#define SP_UART_LSR_BC (1 << 5)
+#define SP_UART_LSR_FE (1 << 4)
+#define SP_UART_LSR_OE (1 << 3)
+#define SP_UART_LSR_PE (1 << 2)
+#define SP_UART_LSR_RX (1 << 1)
+#define SP_UART_LSR_TX (1 << 0)
+
+#define SP_UART_LSR_BRK_ERROR_BITS \
+ (SP_UART_LSR_PE | SP_UART_LSR_OE | SP_UART_LSR_FE | SP_UART_LSR_BC)
+
+/* lcr */
+#define SP_UART_LCR_WL5 (0 << 0)
+#define SP_UART_LCR_WL6 (1 << 0)
+#define SP_UART_LCR_WL7 (2 << 0)
+#define SP_UART_LCR_WL8 (3 << 0)
+#define SP_UART_LCR_ST (1 << 2)
+#define SP_UART_LCR_PE (1 << 3)
+#define SP_UART_LCR_PR (1 << 4)
+#define SP_UART_LCR_BC (1 << 5)
+
+/* isc
+ * SP_UART_ISC_MSM : Modem status ctrl
+ * SP_UART_ISC_LSM : Line status interrupt
+ * SP_UART_ISC_RXM : RX interrupt, when got some input data
+ * SP_UART_ISC_TXM : TX interrupt, when trans start
+ */
+#define SP_UART_ISC_MSM (1 << 7)
+#define SP_UART_ISC_LSM (1 << 6)
+#define SP_UART_ISC_RXM (1 << 5)
+#define SP_UART_ISC_TXM (1 << 4)
+#define HAS_UART_ISC_FLAGMASK 0x0F
+#define SP_UART_ISC_MS (1 << 3)
+#define SP_UART_ISC_LS (1 << 2)
+#define SP_UART_ISC_RX (1 << 1)
+#define SP_UART_ISC_TX (1 << 0)
+
+/* modem control register */
+#define SP_UART_MCR_AT (1 << 7)
+#define SP_UART_MCR_AC (1 << 6)
+#define SP_UART_MCR_AR (1 << 5)
+#define SP_UART_MCR_LB (1 << 4)
+#define SP_UART_MCR_RI (1 << 3)
+#define SP_UART_MCR_DCD (1 << 2)
+#define SP_UART_MCR_RTS (1 << 1)
+#define SP_UART_MCR_DTS (1 << 0)
+
+/* DMA-RX, dma_enable_sel */
+#define DMA_INT (1 << 31)
+#define DMA_MSI_ID_SHIFT 12
+#define DMA_MSI_ID_MASK (0x7F << DMA_MSI_ID_SHIFT)
+#define DMA_SEL_UARTX_SHIFT 8
+#define DMA_SEL_UARTX_MASK (0x07 << DMA_SEL_UARTX_SHIFT)
+#define DMA_SW_RST_B (1 << 7)
+#define DMA_INIT (1 << 6)
+#define DMA_GO (1 << 5)
+#define DMA_AUTO_ENABLE (1 << 4)
+#define DMA_TIMEOUT_INT_EN (1 << 3)
+#define DMA_P_SAFE_DISABLE (1 << 2)
+#define DMA_PBUS_DATA_SWAP (1 << 1)
+#define DMA_ENABLE (1 << 0)
+
+#if !defined(__ASSEMBLY__)
+#define UART_SZ 0x80
+struct regs_uart {
+ u32 uart_data;
+ u32 uart_lsr;
+ u32 uart_msr;
+ u32 uart_lcr;
+ u32 uart_mcr;
+ u32 uart_div_l;
+ u32 uart_div_h;
+ u32 uart_isc;
+ u32 uart_tx_residue;
+ u32 uart_rx_residue;
+ u32 uart_rx_threshold;
+ u32 uart_clk_src;
+};
+
+struct regs_uarxdma {
+ u32 rxdma_enable_sel;
+ u32 rxdma_start_addr;
+ u32 rxdma_timeout_set;
+ u32 rxdma_reserved;
+ u32 rxdma_wr_adr;
+ u32 rxdma_rd_adr;
+ u32 rxdma_length_thr;
+ u32 rxdma_end_addr;
+ u32 rxdma_databytes;
+ u32 rxdma_debug_info;
+};
+
+struct regs_uatxdma {
+ u32 txdma_enable;
+ u32 txdma_sel;
+ u32 txdma_start_addr;
+ u32 txdma_end_addr;
+ u32 txdma_wr_adr;
+ u32 txdma_rd_adr;
+ u32 txdma_status;
+ u32 txdma_tmr_unit;
+ u32 txdma_tmr_cnt;
+ u32 txdma_rst_done;
+};
+
+struct regs_uatxgdma {
+ u32 gdma_hw_ver;
+ u32 gdma_config;
+ u32 gdma_length;
+ u32 gdma_addr;
+ u32 gdma_port_mux;
+ u32 gdma_int_flag;
+ u32 gdma_int_en;
+ u32 gdma_software_reset_status;
+ u32 txdma_tmr_cnt;
+};
+
+#endif /* __ASSEMBLY__ */
+
+#endif /* __SP_UART_H__ */
--
2.7.4
^ permalink raw reply related [flat|nested] 19+ messages in thread
* Re: [PATCH 2/2] serial:sunplus-uart:Add Sunplus SoC UART Driver
2021-11-01 7:48 ` [PATCH 2/2] serial:sunplus-uart:Add " hammer.hsieh
@ 2021-11-01 7:56 ` Greg KH
0 siblings, 0 replies; 19+ messages in thread
From: Greg KH @ 2021-11-01 7:56 UTC (permalink / raw)
To: hammer.hsieh
Cc: linux-serial, devicetree, linux-kernel, jirislaby, p.zabel,
tony.huang, wells.lu, hammer.hsieh
On Mon, Nov 01, 2021 at 03:48:23PM +0800, hammer.hsieh wrote:
> Add Sunplus SoC UART Driver
>
> Signed-off-by: hammer.hsieh <hammer.hsieh@sunplus.com>
I doubt you sign your name with a "." in it, right?
Also this address does not match your From: address. Please fix this up
when resending this.
> ---
> MAINTAINERS | 2 +
> drivers/tty/serial/Kconfig | 23 +
> drivers/tty/serial/Makefile | 1 +
> drivers/tty/serial/sunplus-uart.c | 1848 +++++++++++++++++++++++++++++++++++++
> include/soc/sunplus/sp_uart.h | 158 ++++
> 5 files changed, 2032 insertions(+)
> create mode 100644 drivers/tty/serial/sunplus-uart.c
> create mode 100644 include/soc/sunplus/sp_uart.h
>
> diff --git a/MAINTAINERS b/MAINTAINERS
> index f863e97..0176026 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -17949,6 +17949,8 @@ SUNPLUS UART DRIVER
> M: Hammer Hsieh <hammer.hsieh@sunplus.com>
> S: Maintained
> F: Documentation/devicetree/bindings/serial/sunplus,uart.yaml
> +F: drivers/tty/serial/sunplus-uart.c
> +F: include/soc/sunplus/sp-uart.h
>
> SUPERH
> M: Yoshinori Sato <ysato@users.sourceforge.jp>
> diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig
> index 131a6a5..319f5db 100644
> --- a/drivers/tty/serial/Kconfig
> +++ b/drivers/tty/serial/Kconfig
> @@ -1561,6 +1561,29 @@ config SERIAL_LITEUART_CONSOLE
> and warnings and which allows logins in single user mode).
> Otherwise, say 'N'.
>
> +config SERIAL_SUNPLUS
> + bool "Sunplus UART support"
> + depends on OF
> + select SERIAL_CORE
> + help
> + Select this option if you would like to use Sunplus serial port on
> + Sunplus SoC SP7021.
> + If you enable this option, Sunplus serial ports in the system will
> + be registered as ttySx.
> +
> +config SERIAL_SUNPLUS_CONSOLE
> + bool "Console on Sunplus UART"
> + depends on SERIAL_SUNPLUS
> + select SERIAL_CORE_CONSOLE
> + select SERIAL_EARLYCON
> + help
> + Select this option if you would like to use a Sunplus UART as the
> + system console.
> + Even if you say Y here, the currently visible virtual console
> + (/dev/tty0) will still be used as the system console by default, but
> + you can alter that using a kernel command line option such as
> + "console=ttySx".
> +
> endmenu
>
> config SERIAL_MCTRL_GPIO
> diff --git a/drivers/tty/serial/Makefile b/drivers/tty/serial/Makefile
> index 7da0856..61cc8de 100644
> --- a/drivers/tty/serial/Makefile
> +++ b/drivers/tty/serial/Makefile
> @@ -87,6 +87,7 @@ obj-$(CONFIG_SERIAL_RDA) += rda-uart.o
> obj-$(CONFIG_SERIAL_MILBEAUT_USIO) += milbeaut_usio.o
> obj-$(CONFIG_SERIAL_SIFIVE) += sifive.o
> obj-$(CONFIG_SERIAL_LITEUART) += liteuart.o
> +obj-$(CONFIG_SERIAL_SUNPLUS) += sunplus-uart.o
>
> # GPIOLIB helpers for modem control lines
> obj-$(CONFIG_SERIAL_MCTRL_GPIO) += serial_mctrl_gpio.o
> diff --git a/drivers/tty/serial/sunplus-uart.c b/drivers/tty/serial/sunplus-uart.c
> new file mode 100644
> index 0000000..d1524dc
> --- /dev/null
> +++ b/drivers/tty/serial/sunplus-uart.c
> @@ -0,0 +1,1848 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later
I have to ask,. but are you sure about this license that it needs to be
"-or-later"?
> +/*
> + * Sunplus SoC UART driver
> + *
> + * Author: Hammer Hsieh <hammer.hsieh@sunplus.com>
> + * Tony Huang <tony.huang@sunplus.com>
> + * Wells Lu <wells.lu@sunplus.com>
> + *
> + */
> +
> +#include <linux/module.h>
> +#include <linux/init.h>
> +#include <linux/console.h>
> +#include <linux/interrupt.h>
> +#include <linux/platform_device.h>
> +#include <linux/tty.h>
> +#include <linux/tty_flip.h>
> +#include <linux/of_platform.h>
> +#include <asm/irq.h>
> +#if defined(CONFIG_MAGIC_SYSRQ)
> +#define SUPPORT_SYSRQ
> +#include <linux/sysrq.h>
> +#endif
> +#include <linux/serial_core.h>
> +#include <linux/clk.h>
> +#include <linux/reset.h>
> +#include <linux/io.h>
> +#include <linux/dma-mapping.h>
> +#include <soc/sunplus/sp_uart.h>
> +
> +#ifdef CONFIG_PM_RUNTIME_UART
> +#include <linux/pm_runtime.h>
> +#endif
Why the #ifdef in the .c file?
> +
> +#include <linux/gpio.h>
GPIO in a serial driver?
> +#include <linux/of.h>
> +#include <linux/of_gpio.h>
> +#include <dt-bindings/clock/sp-sp7021.h>
> +#include <dt-bindings/pinctrl/sppctl-sp7021.h>
> +#include <linux/delay.h>
> +#include <linux/hrtimer.h>
Please put the linux/ includes above the dt-bindings ones.
> +
> +#define DEVICE_NAME "ttyS"
> +#define SP_UART_MAJOR TTY_MAJOR
Why is this driver allowed to be named the same as the other serial
drivers? What happens when you plug in a 8250 card to this device?
> +#define SP_UART_MINOR_START 64
Why here?
> +
> +#define NUM_UART 6 /* serial0, ... */
> +#define NUM_UARTDMARX 2 /* serial10, ... */
> +#define NUM_UARTDMATX 2 /* serial20, ... */
Why are these hard codeded?
> +
> +#define ID_BASE_DMARX 10
> +#define ID_BASE_DMATX 20
> +
> +#define IS_UARTDMARX_ID(X) \
> + (((X) >= (ID_BASE_DMARX)) && ((X) < (ID_BASE_DMARX + NUM_UARTDMARX)))
> +#define IS_UARTDMATX_ID(X) \
> + (((X) >= (ID_BASE_DMATX)) && ((X) < (ID_BASE_DMATX + NUM_UARTDMATX)))
> +
> +//#define TTYS_KDBG_INFO
> +#define TTYS_KDBG_ERR
> +//#define TTYS_GPIO
Why is this commented out?
Why is this defined at all?
> +
> +#ifdef TTYS_KDBG_INFO
> +#define DBG_INFO(fmt, args ...) pr_info("K_TTYS: " fmt, ## args)
> +#else
> +#define DBG_INFO(fmt, args ...)
> +#endif
> +#ifdef TTYS_KDBG_ERR
> +#define DBG_ERR(fmt, args ...) pr_err("K_TTYS: " fmt, ## args)
> +#else
> +#define DBG_ERR(fmt, args ...)
> +#endif
No, please use dev_info(), dev_err() and dev_dbg() only. Do not create
your own logging macros for a single driver, use the ones the kernel
gives you.
> +
> +#define SP_UART_CREAD_DISABLED (1 << 16)
> +
> +#define UARXDMA_BUF_SZ PAGE_SIZE
> +#define MAX_SZ_RXDMA_ISR (1 << 9)
> +#define UATXDMA_BUF_SZ PAGE_SIZE
> +
> +#define CLK_HIGH_UART 202500000
> +#define UART_RATIO 232
> +
> +#if defined(CONFIG_SP_MON)
What sets this?
I've stopped reviewing here.
thanks,
greg k-h
^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH 1/2] dt-bindings:serial:Add bindings doc for Sunplus SoC UART Driver
2021-11-01 7:48 ` [PATCH 1/2] dt-bindings:serial:Add bindings doc for Sunplus SoC UART Driver hammer.hsieh
@ 2021-11-01 13:20 ` Rob Herring
2021-11-01 19:34 ` Rob Herring
1 sibling, 0 replies; 19+ messages in thread
From: Rob Herring @ 2021-11-01 13:20 UTC (permalink / raw)
To: hammer.hsieh
Cc: linux-kernel, linux-serial, hammer.hsieh, devicetree, gregkh,
p.zabel, wells.lu, tony.huang, jirislaby
On Mon, 01 Nov 2021 15:48:22 +0800, hammer.hsieh wrote:
> Add bindings doc for Sunplus SoC UART Driver
>
> Signed-off-by: hammer.hsieh <hammer.hsieh@sunplus.com>
> ---
> .../devicetree/bindings/serial/sunplus,uart.yaml | 116 +++++++++++++++++++++
> MAINTAINERS | 5 +
> 2 files changed, 121 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/serial/sunplus,uart.yaml
>
My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check'
on your patch (DT_CHECKER_FLAGS is new in v5.13):
yamllint warnings/errors:
./Documentation/devicetree/bindings/serial/sunplus,uart.yaml:36:9: [warning] wrong indentation: expected 10 but found 8 (indentation)
./Documentation/devicetree/bindings/serial/sunplus,uart.yaml:39:9: [warning] wrong indentation: expected 10 but found 8 (indentation)
./Documentation/devicetree/bindings/serial/sunplus,uart.yaml:42:9: [warning] wrong indentation: expected 10 but found 8 (indentation)
./Documentation/devicetree/bindings/serial/sunplus,uart.yaml:45:9: [warning] wrong indentation: expected 10 but found 8 (indentation)
dtschema/dtc warnings/errors:
Documentation/devicetree/bindings/serial/sunplus,uart.example.dts:20:18: fatal error: dt-bindings/clock/sp-sp7021.h: No such file or directory
20 | #include <dt-bindings/clock/sp-sp7021.h>
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
compilation terminated.
make[1]: *** [scripts/Makefile.lib:385: Documentation/devicetree/bindings/serial/sunplus,uart.example.dt.yaml] Error 1
make[1]: *** Waiting for unfinished jobs....
make: *** [Makefile:1441: dt_binding_check] Error 2
doc reference errors (make refcheckdocs):
See https://patchwork.ozlabs.org/patch/1548996
This check can fail if there are any dependencies. The base for a patch
series is generally the most recent rc1.
If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:
pip3 install dtschema --upgrade
Please check and re-submit.
^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH 1/2] dt-bindings:serial:Add bindings doc for Sunplus SoC UART Driver
2021-11-01 7:48 ` [PATCH 1/2] dt-bindings:serial:Add bindings doc for Sunplus SoC UART Driver hammer.hsieh
2021-11-01 13:20 ` Rob Herring
@ 2021-11-01 19:34 ` Rob Herring
1 sibling, 0 replies; 19+ messages in thread
From: Rob Herring @ 2021-11-01 19:34 UTC (permalink / raw)
To: hammer.hsieh
Cc: gregkh, linux-serial, devicetree, linux-kernel, jirislaby,
p.zabel, tony.huang, wells.lu, hammer.hsieh
On Mon, Nov 01, 2021 at 03:48:22PM +0800, hammer.hsieh wrote:
> Add bindings doc for Sunplus SoC UART Driver
>
> Signed-off-by: hammer.hsieh <hammer.hsieh@sunplus.com>
> ---
> .../devicetree/bindings/serial/sunplus,uart.yaml | 116 +++++++++++++++++++++
> MAINTAINERS | 5 +
> 2 files changed, 121 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/serial/sunplus,uart.yaml
>
> diff --git a/Documentation/devicetree/bindings/serial/sunplus,uart.yaml b/Documentation/devicetree/bindings/serial/sunplus,uart.yaml
> new file mode 100644
> index 0000000..f2ca9ee
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/serial/sunplus,uart.yaml
> @@ -0,0 +1,116 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +# Copyright (C) Sunplus Co., Ltd. 2021
> +%YAML 1.2
> +---
> +$id: "http://devicetree.org/schemas/serial/sunplus,uart.yaml#"
> +$schema: "http://devicetree.org/meta-schemas/core.yaml#"
> +
> +title: Sunplus SoC UART Controller Device Tree Bindings
> +
> +maintainers:
> + - Tony Huang <tony.huang@sunplus.com>
> + - Hammer Hsieh <hammer.hsieh@sunplus.com>
> + - Wells Lu <wells.lu@sunplus.com>
> +
> +allOf:
> + - $ref: serial.yaml#
> +
> +properties:
> + compatible:
> + const: sunplus,sp7021-uart
> +
> + reg:
> + minItems: 1
> + maxItems: 2
> +
> + interrupts:
> + maxItems: 1
> +
> + clocks:
> + minItems: 1
> + maxItems: 2
> +
> + clock-names:
> + oneOf:
> + - items:
> + - const: UADMA
> + - const: PERI0
> + - items:
> + - const: UADMA
> + - const: PERI1
These 2 can be:
items:
- const UADMA
- pattern: '^PERI[0-1]$'
But why the difference for only one model of UART? The names should
reflect the function of the clock.
> + - items:
> + - const: HWUA
> + - const: PERI0
> + - items:
> + - const: HWUA
> + - const: PERI1
> +
> + resets:
> + maxItems: 1
> +
> + which-uart:
> + $ref: /schemas/types.yaml#/definitions/uint32
> + enum: [ 1, 2, 3, 4]
What's this for? Looks like an index and we don't do indices in DT.
There is 'aliases' though.
> +
> +required:
> + - compatible
> + - reg
> + - clocks
> + - resets
> +
> +additionalProperties: false
> +
> +examples:
> + - |
> + #include <dt-bindings/interrupt-controller/irq.h>
> + #include <dt-bindings/clock/sp-sp7021.h>
> + #include <dt-bindings/reset/sp-sp7021.h>
> + aliases {
> + serial0 = &uart0;
> + serial1 = &uart1;
> + serial10 = &uartdmarx0;
> + serial20 = &uartdmatx0;
> + };
> +
> + uart0: serial@9c000900 {
> + compatible = "sunplus,sp7021-uart";
> + reg = <0x9c000900 0x80>;
> + interrupt-parent = <&intc>;
> + interrupts = <53 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&clkc UA0>;
The schema says you must have 2 clocks.
> + resets = <&rstc RST_UA0>;
> + };
> +
> + // UART1 PIO mode
> + uart1: serial@9c000980 {
> + compatible = "sunplus,sp7021-uart";
> + reg = <0x9c000980 0x80>;
> + interrupt-parent = <&intc>;
> + interrupts = <54 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&clkc UA1>;
> + resets = <&rstc RST_UA1>;
> + };
> +
> + // UART1 DMA mode for RX
> + uartdmarx0: serial@9c008980 {
> + compatible = "sunplus,sp7021-uart";
> + reg = <0x9c008980 0x40>;
> + interrupt-parent = <&intc>;
> + interrupts = <138 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&clkc UADMA>, <&clkc PERI0>;
> + clock-names = "UADMA", "PERI0";
> + resets = <&rstc RST_UADMA>;
> + which-uart = <1>;
> + };
> +
> + // UART1 DMA mode for TX
> + uartdmatx0: serial@9c008a00 {
> + compatible = "sunplus,sp7021-uart";
> + reg = <0x9c008a00 0x40>, <0x9c008880 0x80>;
> + clocks = <&clkc HWUA>, <&clkc PERI0>;
> + clock-names = "HWUA", "PERI0";
> + resets = <&rstc RST_HWUA>;
> + which-uart = <1>;
> + };
> +
> +...
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 3b79fd4..f863e97 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -17945,6 +17945,11 @@ L: netdev@vger.kernel.org
> S: Maintained
> F: drivers/net/ethernet/dlink/sundance.c
>
> +SUNPLUS UART DRIVER
> +M: Hammer Hsieh <hammer.hsieh@sunplus.com>
> +S: Maintained
> +F: Documentation/devicetree/bindings/serial/sunplus,uart.yaml
> +
> SUPERH
> M: Yoshinori Sato <ysato@users.sourceforge.jp>
> M: Rich Felker <dalias@libc.org>
> --
> 2.7.4
>
>
^ permalink raw reply [flat|nested] 19+ messages in thread
* [PATCH v2 0/2] Add UART driver for Suplus SP7021 SoC
2021-11-01 7:48 [PATCH 0/2] Add UART driver for Suplus SP7021 SoC hammer.hsieh
2021-11-01 7:48 ` [PATCH 1/2] dt-bindings:serial:Add bindings doc for Sunplus SoC UART Driver hammer.hsieh
2021-11-01 7:48 ` [PATCH 2/2] serial:sunplus-uart:Add " hammer.hsieh
@ 2021-11-10 7:51 ` Hammer Hsieh
2021-11-10 7:51 ` [PATCH v2 1/2] dt-bindings:serial:Add bindings doc for Sunplus SoC UART Driver Hammer Hsieh
` (2 more replies)
2021-11-19 5:19 ` [PATCH v3 " Hammer Hsieh
3 siblings, 3 replies; 19+ messages in thread
From: Hammer Hsieh @ 2021-11-10 7:51 UTC (permalink / raw)
To: gregkh, robh+dt, linux-serial, devicetree, linux-kernel,
jirislaby, p.zabel
Cc: tony.huang, wells.lu, Hammer Hsieh
This is a patch series for UART driver for Suplus SP7021 SoC.
Sunplus SP7021 is an ARM Cortex A7 (4 cores) based SoC. It integrates
many peripherals (ex: UART. I2C, SPI, SDIO, eMMC, USB, SD card and
etc.) into a single chip. It is designed for industrial control.
Refer to:
https://sunplus-tibbo.atlassian.net/wiki/spaces/doc/overview
https://tibbo.com/store/plus1.html
Hammer Hsieh (2):
dt-bindings:serial:Add bindings doc for Sunplus SoC UART Driver
serial:sunplus-uart:Add Sunplus SoC UART Driver
.../bindings/serial/sunplus,sp7021-uart.yaml | 157 ++
MAINTAINERS | 7 +
drivers/tty/serial/Kconfig | 23 +
drivers/tty/serial/Makefile | 1 +
drivers/tty/serial/sunplus-uart.c | 1591 ++++++++++++++++++++
include/soc/sunplus/sp_uart.h | 147 ++
6 files changed, 1926 insertions(+)
create mode 100644 Documentation/devicetree/bindings/serial/sunplus,sp7021-uart.yaml
create mode 100644 drivers/tty/serial/sunplus-uart.c
create mode 100644 include/soc/sunplus/sp_uart.h
--
2.7.4
^ permalink raw reply [flat|nested] 19+ messages in thread
* [PATCH v2 1/2] dt-bindings:serial:Add bindings doc for Sunplus SoC UART Driver
2021-11-10 7:51 ` [PATCH v2 0/2] Add UART driver for Suplus SP7021 SoC Hammer Hsieh
@ 2021-11-10 7:51 ` Hammer Hsieh
2021-11-10 7:51 ` [PATCH v2 2/2] serial:sunplus-uart:Add " Hammer Hsieh
2021-11-10 16:41 ` [PATCH v2 0/2] Add UART driver for Suplus SP7021 SoC Andy Shevchenko
2 siblings, 0 replies; 19+ messages in thread
From: Hammer Hsieh @ 2021-11-10 7:51 UTC (permalink / raw)
To: gregkh, robh+dt, linux-serial, devicetree, linux-kernel,
jirislaby, p.zabel
Cc: tony.huang, wells.lu, Hammer Hsieh
Add bindings doc for Sunplus SoC UART Driver
Signed-off-by: Hammer Hsieh <hammer.hsieh@sunplus.com>
---
Changes in v2:
- Addressed all comments from Mr. Rob Herring.
.../bindings/serial/sunplus,sp7021-uart.yaml | 157 +++++++++++++++++++++
MAINTAINERS | 5 +
2 files changed, 162 insertions(+)
create mode 100644 Documentation/devicetree/bindings/serial/sunplus,sp7021-uart.yaml
diff --git a/Documentation/devicetree/bindings/serial/sunplus,sp7021-uart.yaml b/Documentation/devicetree/bindings/serial/sunplus,sp7021-uart.yaml
new file mode 100644
index 0000000..3f46f3e
--- /dev/null
+++ b/Documentation/devicetree/bindings/serial/sunplus,sp7021-uart.yaml
@@ -0,0 +1,157 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+# Copyright (C) Sunplus Co., Ltd. 2021
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/serial/sunplus,sp7021-uart.yaml#"
+$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+
+title: Sunplus SoC SP7021 UART Controller Device Tree Bindings
+
+maintainers:
+ - Tony Huang <tony.huang@sunplus.com>
+ - Hammer Hsieh <hammer.hsieh@sunplus.com>
+ - Wells Lu <wells.lu@sunplus.com>
+
+allOf:
+ - $ref: serial.yaml#
+
+properties:
+ compatible:
+ const: sunplus,sp7021-uart
+
+ reg:
+ minItems: 1
+ maxItems: 2
+
+ interrupts:
+ maxItems: 1
+
+ clocks:
+ minItems: 1
+ maxItems: 2
+
+ clock-names:
+ oneOf:
+ - items:
+ - const: UADMA
+ - pattern: '^PERI[0-1]$'
+ - items:
+ - const: HWUA
+ - pattern: '^PERI[0-1]$'
+
+ resets:
+ maxItems: 1
+
+ which-uart:
+ description:
+ UA1-4 support DMA mode, UA0 support PIO mode only.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [ 1, 2, 3, 4]
+
+required:
+ - compatible
+ - reg
+ - clocks
+ - resets
+
+if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - sunplus,sp7021-uart-rxdma
+ - sunplus,sp7021-uart-txdma
+then:
+ required:
+ - clock-names
+ - which-uart
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/irq.h>
+ aliases {
+ serial0 = &uart0;
+ serial1 = &uart1;
+ serial2 = &uart2;
+ serial10 = &uartdmarx0;
+ serial20 = &uartdmatx0;
+ serial11 = &uartdmarx1;
+ serial21 = &uartdmatx1;
+ };
+
+ // UART0 PIO mode only
+ uart0: serial@9c000900 {
+ compatible = "sunplus,sp7021-uart";
+ reg = <0x9c000900 0x80>;
+ interrupt-parent = <&intc>;
+ interrupts = <53 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clkc 0x28>;
+ resets = <&rstc 0x18>;
+ };
+
+ // UART1 PIO mode
+ uart1: serial@9c000980 {
+ compatible = "sunplus,sp7021-uart";
+ reg = <0x9c000980 0x80>;
+ interrupt-parent = <&intc>;
+ interrupts = <54 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clkc 0x29>;
+ resets = <&rstc 0x19>;
+ };
+
+ // UART1 DMA mode for RX
+ uartdmarx0: serial@9c008980 {
+ compatible = "sunplus,sp7021-uart-rxdma";
+ reg = <0x9c008980 0x40>;
+ interrupt-parent = <&intc>;
+ interrupts = <138 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clkc 0x2f>, <&clkc 0x1b>;
+ clock-names = "UADMA", "PERI0";
+ resets = <&rstc 0x1f>;
+ which-uart = <1>;
+ };
+
+ // UART1 DMA mode for TX
+ uartdmatx0: serial@9c008a00 {
+ compatible = "sunplus,sp7021-uart-txdma";
+ reg = <0x9c008a00 0x40>, <0x9c008880 0x80>;
+ clocks = <&clkc 0x2d>, <&clkc 0x1b>;
+ clock-names = "HWUA", "PERI0";
+ resets = <&rstc 0x1d>;
+ which-uart = <1>;
+ };
+
+ // UART2 PIO mode
+ uart2: serial@9c000800 {
+ compatible = "sunplus,sp7021-uart";
+ reg = <0x9c000800 0x80>;
+ interrupt-parent = <&intc>;
+ interrupts = <55 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clkc 0x2a>;
+ resets = <&rstc 0x1a>;
+ };
+
+ // UART2 DMA mode for RX
+ uartdmarx1: serial@9c0089c0 {
+ compatible = "sunplus,sp7021-uart-rxdma";
+ reg = <0x9c0089c0 0x40>;
+ interrupt-parent = <&intc>;
+ interrupts = <139 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clkc 0x2f>, <&clkc 0x1f>;
+ clock-names = "UADMA", "PERI1";
+ resets = <&rstc 0x1f>;
+ which-uart = <2>;
+ };
+
+ // UART2 DMA mode for TX
+ uartdmatx1: serial@9c008a40 {
+ compatible = "sunplus,sp7021-uart-txdma";
+ reg = <0x9c008a40 0x40>, <0x9c008900 0x80>;
+ clocks = <&clkc 0x2d>, <&clkc 0x1f>;
+ clock-names = "HWUA", "PERI1";
+ resets = <&rstc 0x1d>;
+ which-uart = <2>;
+ };
+...
diff --git a/MAINTAINERS b/MAINTAINERS
index 3b79fd4..f2ee40c 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -17945,6 +17945,11 @@ L: netdev@vger.kernel.org
S: Maintained
F: drivers/net/ethernet/dlink/sundance.c
+SUNPLUS UART DRIVER
+M: Hammer Hsieh <hammer.hsieh@sunplus.com>
+S: Maintained
+F: Documentation/devicetree/bindings/serial/sunplus,sp7021-uart.yaml
+
SUPERH
M: Yoshinori Sato <ysato@users.sourceforge.jp>
M: Rich Felker <dalias@libc.org>
--
2.7.4
^ permalink raw reply related [flat|nested] 19+ messages in thread
* [PATCH v2 2/2] serial:sunplus-uart:Add Sunplus SoC UART Driver
2021-11-10 7:51 ` [PATCH v2 0/2] Add UART driver for Suplus SP7021 SoC Hammer Hsieh
2021-11-10 7:51 ` [PATCH v2 1/2] dt-bindings:serial:Add bindings doc for Sunplus SoC UART Driver Hammer Hsieh
@ 2021-11-10 7:51 ` Hammer Hsieh
2021-11-10 9:50 ` Philipp Zabel
2021-11-12 8:31 ` kernel test robot
2021-11-10 16:41 ` [PATCH v2 0/2] Add UART driver for Suplus SP7021 SoC Andy Shevchenko
2 siblings, 2 replies; 19+ messages in thread
From: Hammer Hsieh @ 2021-11-10 7:51 UTC (permalink / raw)
To: gregkh, robh+dt, linux-serial, devicetree, linux-kernel,
jirislaby, p.zabel
Cc: tony.huang, wells.lu, Hammer Hsieh
Add Sunplus SoC UART Driver
Signed-off-by: Hammer Hsieh <hammer.hsieh@sunplus.com>
---
Changes in v2:
- Addressed all comments from Mr. Greg Kroah-Hartman.
MAINTAINERS | 2 +
drivers/tty/serial/Kconfig | 23 +
drivers/tty/serial/Makefile | 1 +
drivers/tty/serial/sunplus-uart.c | 1591 +++++++++++++++++++++++++++++++++++++
include/soc/sunplus/sp_uart.h | 147 ++++
5 files changed, 1764 insertions(+)
create mode 100644 drivers/tty/serial/sunplus-uart.c
create mode 100644 include/soc/sunplus/sp_uart.h
diff --git a/MAINTAINERS b/MAINTAINERS
index f2ee40c..14790a4 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -17949,6 +17949,8 @@ SUNPLUS UART DRIVER
M: Hammer Hsieh <hammer.hsieh@sunplus.com>
S: Maintained
F: Documentation/devicetree/bindings/serial/sunplus,sp7021-uart.yaml
+F: drivers/tty/serial/sunplus-uart.c
+F: include/soc/sunplus/sp-uart.h
SUPERH
M: Yoshinori Sato <ysato@users.sourceforge.jp>
diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig
index 131a6a5..319f5db 100644
--- a/drivers/tty/serial/Kconfig
+++ b/drivers/tty/serial/Kconfig
@@ -1561,6 +1561,29 @@ config SERIAL_LITEUART_CONSOLE
and warnings and which allows logins in single user mode).
Otherwise, say 'N'.
+config SERIAL_SUNPLUS
+ bool "Sunplus UART support"
+ depends on OF
+ select SERIAL_CORE
+ help
+ Select this option if you would like to use Sunplus serial port on
+ Sunplus SoC SP7021.
+ If you enable this option, Sunplus serial ports in the system will
+ be registered as ttySx.
+
+config SERIAL_SUNPLUS_CONSOLE
+ bool "Console on Sunplus UART"
+ depends on SERIAL_SUNPLUS
+ select SERIAL_CORE_CONSOLE
+ select SERIAL_EARLYCON
+ help
+ Select this option if you would like to use a Sunplus UART as the
+ system console.
+ Even if you say Y here, the currently visible virtual console
+ (/dev/tty0) will still be used as the system console by default, but
+ you can alter that using a kernel command line option such as
+ "console=ttySx".
+
endmenu
config SERIAL_MCTRL_GPIO
diff --git a/drivers/tty/serial/Makefile b/drivers/tty/serial/Makefile
index 7da0856..61cc8de 100644
--- a/drivers/tty/serial/Makefile
+++ b/drivers/tty/serial/Makefile
@@ -87,6 +87,7 @@ obj-$(CONFIG_SERIAL_RDA) += rda-uart.o
obj-$(CONFIG_SERIAL_MILBEAUT_USIO) += milbeaut_usio.o
obj-$(CONFIG_SERIAL_SIFIVE) += sifive.o
obj-$(CONFIG_SERIAL_LITEUART) += liteuart.o
+obj-$(CONFIG_SERIAL_SUNPLUS) += sunplus-uart.o
# GPIOLIB helpers for modem control lines
obj-$(CONFIG_SERIAL_MCTRL_GPIO) += serial_mctrl_gpio.o
diff --git a/drivers/tty/serial/sunplus-uart.c b/drivers/tty/serial/sunplus-uart.c
new file mode 100644
index 0000000..bfc19e2
--- /dev/null
+++ b/drivers/tty/serial/sunplus-uart.c
@@ -0,0 +1,1591 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Sunplus SoC UART driver
+ *
+ * Author: Hammer Hsieh <hammer.hsieh@sunplus.com>
+ * Tony Huang <tony.huang@sunplus.com>
+ * Wells Lu <wells.lu@sunplus.com>
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/console.h>
+#include <linux/interrupt.h>
+#include <linux/platform_device.h>
+#include <linux/tty.h>
+#include <linux/tty_flip.h>
+#include <linux/of_platform.h>
+#include <asm/irq.h>
+#include <linux/sysrq.h>
+#include <linux/serial_core.h>
+#include <linux/clk.h>
+#include <linux/reset.h>
+#include <linux/io.h>
+#include <linux/dma-mapping.h>
+#include <linux/pm_runtime.h>
+#include <linux/of.h>
+#include <linux/of_gpio.h>
+#include <linux/delay.h>
+#include <linux/hrtimer.h>
+#include <soc/sunplus/sp_uart.h>
+#include <dt-bindings/clock/sp-sp7021.h>
+
+/*
+ * UART_NR : Nunmer of UART channel, serial0, ...
+ * UART_DMARX_NR : Nunmer of UART RX DMA, serial10, ...
+ * UART_DMATX_NR : Nunmer of UART TX DMA, serial20, ...
+ *
+ */
+#define UART_NR 5
+#define UART_DMARX_NR 2
+#define UART_DMATX_NR 2
+
+/*
+ * IS_UARTDMARX_ID(X) : if true , do rxdma init in probe
+ * IS_UARTDMATX_ID(X) : if true , do txdma init in probe
+ *
+ */
+#define ID_BASE_DMARX 10
+#define ID_BASE_DMATX 20
+
+#define IS_UARTDMARX_ID(X) \
+ (((X) >= (ID_BASE_DMARX)) && ((X) < (ID_BASE_DMARX + UART_DMARX_NR)))
+#define IS_UARTDMATX_ID(X) \
+ (((X) >= (ID_BASE_DMATX)) && ((X) < (ID_BASE_DMATX + UART_DMATX_NR)))
+
+struct sunplus_uart_port {
+ char name[16];
+ struct uart_port uport;
+ struct sunplus_dma_info *uartdma_rx;
+ struct sunplus_dma_info *uartdma_tx;
+ struct clk *clk;
+ struct reset_control *rstc;
+ unsigned int pllsys_rate;
+ struct gpio_desc *rts_gpio;
+ struct hrtimer rts_check_tx_empty;
+ struct hrtimer rts_delay_before_send;
+ struct hrtimer rts_delay_after_send;
+};
+struct sunplus_uart_port sunplus_uart_ports[UART_NR];
+static struct uart_driver sunplus_uart_driver;
+
+struct sunplus_dma_info {
+ void __iomem *membase;
+ void __iomem *gdma_membase;
+ unsigned long addr_phy;
+ int irq;
+ int which_uart;
+ struct sunplus_uart_port *binding_port;
+ void *buf_va;
+ dma_addr_t dma_handle;
+};
+static struct sunplus_dma_info
+ sunplus_uartdma[UART_DMARX_NR + UART_DMATX_NR];
+
+static inline struct sunplus_uart_port *to_sunplus_uart(struct uart_port *uport)
+{
+ return container_of(uport, struct sunplus_uart_port, uport);
+}
+
+static inline void sp_uart_put_char(struct uart_port *port, unsigned int ch)
+{
+ struct sunplus_uart_port *sp_port = to_sunplus_uart(port);
+ struct sunplus_dma_info *tx_dma = sp_port->uartdma_tx;
+ u32 addr_sw, addr_start;
+ u32 offset_sw;
+ u8 *byte_ptr;
+
+ if (!tx_dma) {
+ writel(ch, port->membase + SP_UART_DATA);
+ } else {
+ addr_sw = readl(tx_dma->membase + SP_UART_TXDMA_WR_ADR);
+ addr_start = readl(tx_dma->membase + SP_UART_TXDMA_START_ADDR);
+ offset_sw = addr_sw - addr_start;
+ byte_ptr = (u8 *)(tx_dma->buf_va + offset_sw);
+ *byte_ptr = (u8)(ch);
+ if (offset_sw == (PAGE_SIZE - 1))
+ writel((u32)(tx_dma->dma_handle),
+ tx_dma->membase + SP_UART_TXDMA_WR_ADR);
+ else
+ writel((addr_sw + 1),
+ tx_dma->membase + SP_UART_TXDMA_WR_ADR);
+ }
+}
+
+static inline u32 sp_uart_line_status_tx_buf_not_full(struct uart_port *port)
+{
+ struct sunplus_uart_port *sp_port = to_sunplus_uart(port);
+ struct sunplus_dma_info *tx_dma = sp_port->uartdma_tx;
+ u32 addr_sw, addr_hw;
+
+ if (tx_dma) {
+ if (readl(tx_dma->membase + SP_UART_TXDMA_STATUS) & TXDMA_BUF_FULL)
+ return 0;
+
+ addr_sw = readl(tx_dma->membase + SP_UART_TXDMA_WR_ADR);
+ addr_hw = readl(tx_dma->membase + SP_UART_TXDMA_RD_ADR);
+ if (addr_sw >= addr_hw)
+ return (PAGE_SIZE - (addr_sw - addr_hw));
+ else
+ return (addr_hw - addr_sw);
+
+ } else {
+ if (readl(port->membase + SP_UART_LSR) & SP_UART_LSR_TX)
+ return 1;
+ else
+ return 0;
+ }
+}
+
+/*
+ * Note:
+ * When (uart0_as_console == 0), please make sure:
+ * There is no "console=ttyS0,115200", "earlyprintk", ... in kernel command line.
+ * In /etc/inittab, there is no something like "ttyS0::respawn:/bin/sh"
+ */
+unsigned int uart0_as_console = ~0;
+unsigned int uart_enable_status = ~0;
+
+static struct sunplus_dma_info *sunplus_uartdma_rx_binding(int id)
+{
+ int i;
+
+ for (i = 0; i < UART_DMARX_NR; i++) {
+ if ((sunplus_uartdma[i].which_uart == id) && (sunplus_uartdma[i].membase)) {
+ sunplus_uartdma[i].binding_port = &sunplus_uart_ports[id];
+ return &sunplus_uartdma[i];
+ }
+ }
+ return NULL;
+}
+
+static struct sunplus_dma_info *sunplus_uartdma_tx_binding(int id)
+{
+ int i;
+
+ for (i = UART_DMARX_NR; i < (UART_DMARX_NR + UART_DMATX_NR); i++) {
+ if ((sunplus_uartdma[i].which_uart == id) && (sunplus_uartdma[i].membase)) {
+ sunplus_uartdma[i].binding_port = &sunplus_uart_ports[id];
+ return &sunplus_uartdma[i];
+ }
+ }
+ return NULL;
+}
+
+static inline void wait_for_xmitr(struct uart_port *port)
+{
+ while (1) {
+ if (sp_uart_line_status_tx_buf_not_full(port))
+ break;
+ }
+}
+
+static unsigned int sunplus_tx_empty(struct uart_port *port)
+{
+ struct sunplus_uart_port *sp_port = to_sunplus_uart(port);
+ struct sunplus_dma_info *tx_dma = sp_port->uartdma_tx;
+
+ if (tx_dma) {
+ if (readl(tx_dma->membase + SP_UART_TXDMA_STATUS) & TXDMA_BUF_EMPTY)
+ return TIOCSER_TEMT;
+ else
+ return 0;
+ } else {
+ return ((readl(port->membase + SP_UART_LSR) & SP_UART_LSR_TXE)
+ ? TIOCSER_TEMT : 0);
+ }
+}
+
+static void sunplus_set_mctrl(struct uart_port *port, unsigned int mctrl)
+{
+ struct sunplus_uart_port *sp_port = to_sunplus_uart(port);
+ unsigned int mcr = readl(port->membase + SP_UART_MCR);
+ ktime_t ktime;
+
+ if (mctrl & TIOCM_DTR)
+ mcr |= SP_UART_MCR_DTS;
+ else
+ mcr &= ~SP_UART_MCR_DTS;
+
+ if (mctrl & TIOCM_RTS) {
+ if ((sp_port->uport.rs485.flags & SER_RS485_ENABLED)
+ && (sp_port->uport.rs485.flags & SER_RS485_RTS_ON_SEND))
+ mcr &= ~SP_UART_MCR_RTS; /* RTS invert */
+ else
+ mcr |= SP_UART_MCR_RTS;
+ } else {
+ /* data transfer ended */
+ if (sp_port->uport.rs485.flags & SER_RS485_ENABLED)
+ return;
+
+ mcr &= ~SP_UART_MCR_RTS;
+ }
+
+ if (mctrl & TIOCM_CAR)
+ mcr |= SP_UART_MCR_DCD;
+ else
+ mcr &= ~SP_UART_MCR_DCD;
+
+ if (mctrl & TIOCM_RI)
+ mcr |= SP_UART_MCR_RI;
+ else
+ mcr &= ~SP_UART_MCR_RI;
+
+ if (mctrl & TIOCM_LOOP)
+ mcr |= SP_UART_MCR_LB;
+ else
+ mcr &= ~SP_UART_MCR_LB;
+
+ writel(mcr, port->membase + SP_UART_MCR);
+
+ if (sp_port->uport.rs485.flags & SER_RS485_ENABLED) {
+ mcr = readl(port->membase + SP_UART_MCR);
+ if (mctrl & TIOCM_RTS) {
+ if (((mcr & SP_UART_MCR_RTS)
+ && (sp_port->uport.rs485.flags & SER_RS485_RTS_AFTER_SEND))
+ || (sp_port->uport.rs485.flags & SER_RS485_RTS_ON_SEND)) {
+ if (!IS_ERR(sp_port->rts_gpio))
+ gpiod_set_value(sp_port->rts_gpio, 1);
+ dev_dbg(port->dev, "%s set rts_gpio=1\n", port->name);
+ if (sp_port->uport.rs485.delay_rts_before_send == 0) {
+ ktime = ktime_set(0, 500000); /* 500us */
+ hrtimer_start(&sp_port->rts_check_tx_empty,
+ ktime, HRTIMER_MODE_REL);
+ }
+ }
+ }
+ }
+}
+
+static unsigned int sunplus_get_mctrl(struct uart_port *port)
+{
+ unsigned int ret, mcr;
+
+ mcr = readl(port->membase + SP_UART_MCR);
+
+ if (mcr & SP_UART_MCR_DTS)
+ ret |= TIOCM_DTR;
+
+ if (mcr & SP_UART_MCR_RTS)
+ ret |= TIOCM_RTS;
+
+ if (mcr & SP_UART_MCR_DCD)
+ ret |= TIOCM_CAR;
+
+ if (mcr & SP_UART_MCR_RI)
+ ret |= TIOCM_RI;
+
+ if (mcr & SP_UART_MCR_LB)
+ ret |= TIOCM_LOOP;
+
+ if (mcr & SP_UART_MCR_AC)
+ ret |= TIOCM_CTS;
+
+ return ret;
+}
+
+static void sunplus_stop_tx(struct uart_port *port)
+{
+ unsigned int isc;
+
+ isc = readl(port->membase + SP_UART_ISC);
+ isc &= ~SP_UART_ISC_TXM;
+ writel(isc, port->membase + SP_UART_ISC);
+}
+
+static inline void __start_tx(struct uart_port *port)
+{
+ unsigned int isc;
+
+ isc = readl(port->membase + SP_UART_ISC);
+ isc |= SP_UART_ISC_TXM;
+ writel(isc, port->membase + SP_UART_ISC);
+}
+
+static void sunplus_start_tx(struct uart_port *port)
+{
+ struct sunplus_uart_port *sp_port = to_sunplus_uart(port);
+ ktime_t ktime;
+ int val;
+
+ if (sp_port->uport.rs485.flags & SER_RS485_ENABLED) {
+ val = (sp_port->uport.rs485.flags & SER_RS485_RTS_ON_SEND ? 1 : 0);
+ if (!IS_ERR(sp_port->rts_gpio))
+ gpiod_set_value(sp_port->rts_gpio, val);
+
+ dev_dbg(port->dev, "%s set rts_gpio=%d\n", sp_port->uport.name, val);
+ if (sp_port->uport.rs485.delay_rts_before_send > 0) {
+ long nsec = sp_port->uport.rs485.delay_rts_before_send * 1000000;
+
+ ktime = ktime_set(0, nsec);
+ hrtimer_start(&sp_port->rts_delay_before_send, ktime, HRTIMER_MODE_REL);
+ return;
+ }
+ }
+ __start_tx(port);
+}
+
+static void sunplus_stop_rx(struct uart_port *port)
+{
+ unsigned int isc;
+
+ isc = readl(port->membase + SP_UART_ISC);
+ isc &= ~SP_UART_ISC_RXM;
+ writel(isc, port->membase + SP_UART_ISC);
+}
+
+static void sunplus_enable_ms(struct uart_port *port)
+{
+ /* Do nothing */
+}
+
+static void sunplus_break_ctl(struct uart_port *port, int ctl)
+{
+ unsigned long flags;
+ unsigned int lcr;
+
+ spin_lock_irqsave(&port->lock, flags);
+
+ lcr = readl(port->membase + SP_UART_LCR);
+
+ if (ctl != 0)
+ lcr |= SP_UART_LCR_BC; /* start break */
+ else
+ lcr &= ~SP_UART_LCR_BC; /* stop break */
+
+ writel(lcr, port->membase + SP_UART_LCR);
+
+ spin_unlock_irqrestore(&port->lock, flags);
+}
+
+static void transmit_chars(struct uart_port *port)
+{
+ struct sunplus_uart_port *sp_port = to_sunplus_uart(port);
+ struct sunplus_dma_info *tx_dma = sp_port->uartdma_tx;
+ u32 tx_buf_available;
+ u32 addr_sw, addr_start;
+ u32 offset_sw;
+ u8 *byte_ptr;
+ struct circ_buf *xmit = &port->state->xmit;
+
+ if (port->x_char) {
+ sp_uart_put_char(port, port->x_char);
+ port->icount.tx++;
+ port->x_char = 0;
+ return;
+ }
+
+ if (uart_circ_empty(xmit) || uart_tx_stopped(port)) {
+ sunplus_stop_tx(port);
+ return;
+ }
+
+ if (tx_dma) {
+ addr_sw = readl(tx_dma->membase + SP_UART_TXDMA_WR_ADR);
+ addr_start = readl(tx_dma->membase + SP_UART_TXDMA_START_ADDR);
+ offset_sw = addr_sw - addr_start;
+ byte_ptr = (u8 *)(tx_dma->buf_va + offset_sw);
+ tx_buf_available = sp_uart_line_status_tx_buf_not_full(port);
+ while (tx_buf_available) {
+ *byte_ptr = xmit->buf[xmit->tail];
+ xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
+ port->icount.tx++;
+
+ byte_ptr++;
+ addr_sw++;
+ offset_sw++;
+ tx_buf_available--;
+ if (offset_sw == PAGE_SIZE) {
+ offset_sw = 0;
+ addr_sw = (u32)(tx_dma->dma_handle);
+ byte_ptr = (u8 *)(tx_dma->buf_va);
+ }
+
+ if (uart_circ_empty(xmit))
+ break;
+ }
+ writel(addr_sw, tx_dma->membase + SP_UART_TXDMA_WR_ADR);
+ } else {
+ do {
+ sp_uart_put_char(port, xmit->buf[xmit->tail]);
+ xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
+ port->icount.tx++;
+
+ if (uart_circ_empty(xmit))
+ break;
+ } while (sp_uart_line_status_tx_buf_not_full(port));
+ }
+
+ if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
+ uart_write_wakeup(port);
+
+ if (uart_circ_empty(xmit))
+ sunplus_stop_tx(port);
+}
+
+/* called by ISR */
+static void receive_chars(struct uart_port *port)
+{
+ struct tty_struct *tty = port->state->port.tty;
+ unsigned int lsr = readl(port->membase + SP_UART_LSR);
+ unsigned int ch, flag;
+
+ do {
+ ch = readl(port->membase + SP_UART_DATA);
+
+ flag = TTY_NORMAL;
+ port->icount.rx++;
+
+ if (unlikely(lsr & SP_UART_LSR_BRK_ERROR_BITS)) {
+ if (port->cons == NULL)
+ dev_err(port->dev, "UART%d, SP_UART_LSR_BRK_ERROR_BITS, lsr = 0x%08X\n",
+ port->line, lsr);
+
+ if (lsr & SP_UART_LSR_BC) {
+ lsr &= ~(SP_UART_LSR_FE | SP_UART_LSR_PE);
+ port->icount.brk++;
+ if (uart_handle_break(port))
+ goto ignore_char;
+ } else if (lsr & SP_UART_LSR_PE) {
+ if (port->cons == NULL)
+ dev_err(port->dev, "UART%d, SP_UART_LSR_PE\n", port->line);
+ port->icount.parity++;
+ } else if (lsr & SP_UART_LSR_FE) {
+ if (port->cons == NULL)
+ dev_err(port->dev, "UART%d, SP_UART_LSR_FE\n", port->line);
+ port->icount.frame++;
+ }
+ if (lsr & SP_UART_LSR_OE) {
+ if (port->cons == NULL)
+ dev_err(port->dev, "UART%d, SP_UART_LSR_OE\n", port->line);
+ port->icount.overrun++;
+ }
+
+ /*
+ * Mask off conditions which should be ignored.
+ */
+
+ /* lsr &= port->read_status_mask; */
+
+ if (lsr & SP_UART_LSR_BC)
+ flag = TTY_BREAK;
+ else if (lsr & SP_UART_LSR_PE)
+ flag = TTY_PARITY;
+ else if (lsr & SP_UART_LSR_FE)
+ flag = TTY_FRAME;
+ }
+
+ if (port->ignore_status_mask & SP_UART_CREAD_DISABLED)
+ goto ignore_char;
+
+ if (uart_handle_sysrq_char(port, ch))
+ goto ignore_char;
+
+ uart_insert_char(port, lsr, SP_UART_LSR_OE, ch, flag);
+
+ignore_char:
+ lsr = readl(port->membase + SP_UART_LSR);
+ } while (lsr & SP_UART_LSR_RX);
+
+ if (tty) {
+ spin_unlock(&port->lock);
+ tty_flip_buffer_push(tty->port);
+ spin_lock(&port->lock);
+ }
+}
+
+static irqreturn_t sunplus_uart_irq(int irq, void *args)
+{
+ struct uart_port *port = (struct uart_port *)args;
+ unsigned long flags;
+
+ spin_lock_irqsave(&port->lock, flags);
+
+ if (readl(port->membase + SP_UART_ISC) & SP_UART_ISC_RX)
+ receive_chars(port);
+
+ if (readl(port->membase + SP_UART_ISC) & SP_UART_ISC_TX)
+ transmit_chars(port);
+
+ spin_unlock_irqrestore(&port->lock, flags);
+
+ return IRQ_HANDLED;
+}
+
+/* called by ISR */
+static void receive_chars_rxdma(struct uart_port *port)
+{
+ struct sunplus_uart_port *sp_port = to_sunplus_uart(port);
+ struct sunplus_dma_info *rx_dma = sp_port->uartdma_rx;
+ struct tty_struct *tty = port->state->port.tty;
+ u32 offset_sw, offset_hw, rx_size, dma_start;
+ u8 *sw_ptr, *buf_end_ptr, *u8_ptr;
+ u32 icount_rx;
+ u32 tmp_u32, value;
+ u8 tmp_buf[32];
+ int i;
+
+ dma_start = readl(rx_dma->membase + SP_UART_RXDMA_START_ADDR);
+ offset_sw = readl(rx_dma->membase + SP_UART_RXDMA_RD_ADR) - dma_start;
+ offset_hw = readl(rx_dma->membase + SP_UART_RXDMA_WR_ADR) - dma_start;
+
+ if (offset_hw >= offset_sw)
+ rx_size = offset_hw - offset_sw;
+ else
+ rx_size = offset_hw + PAGE_SIZE - offset_sw;
+
+ sw_ptr = (u8 *)(rx_dma->buf_va + offset_sw);
+ buf_end_ptr = (u8 *)(rx_dma->buf_va + PAGE_SIZE);
+
+ /*
+ * Retrieve all data in ISR.
+ * The max. received size is (buffer_size - threshold_size)
+ * = (rxdma_length_thr[31:16] - rxdma_length_thr[15:0])
+ * In order to limit the execution time in this ISR:
+ * => Increase rxdma_length_thr[15:0] to shorten each ISR execution time.
+ * => Don't need to set a small threshold_size,
+ * and split a long ISR into several shorter ISRs.
+ */
+ icount_rx = 0;
+ while (rx_size > icount_rx) {
+ /* 32-byte aligned */
+ if (!(((unsigned long)(sw_ptr)) & (32 - 1))
+ && ((rx_size - icount_rx) >= 32)) {
+ /*
+ * Copy 32 bytes data from non cache area to cache area.
+ * => It should use less DRAM controller's read command.
+ */
+ memcpy(tmp_buf, sw_ptr, 32);
+ u8_ptr = (u8 *)(tmp_buf);
+ for (i = 0; i < 32; i++) {
+ port->icount.rx++;
+ uart_insert_char(port, 0, SP_UART_LSR_OE,
+ (unsigned int)(*u8_ptr), TTY_NORMAL);
+ u8_ptr++;
+ }
+ sw_ptr += 32;
+ icount_rx += 32;
+ } else {
+ port->icount.rx++;
+ uart_insert_char(port, 0, SP_UART_LSR_OE,
+ (unsigned int)(*sw_ptr), TTY_NORMAL);
+ sw_ptr++;
+ icount_rx++;
+ }
+ if (sw_ptr >= buf_end_ptr)
+ sw_ptr = (u8 *)(rx_dma->buf_va);
+ }
+
+ tmp_u32 = readl(rx_dma->membase + SP_UART_RXDMA_RD_ADR) + rx_size;
+
+ if (tmp_u32 <= readl(rx_dma->membase + SP_UART_RXDMA_END_ADDR))
+ writel(tmp_u32, rx_dma->membase + SP_UART_RXDMA_RD_ADR);
+ else
+ writel((tmp_u32 - PAGE_SIZE), rx_dma->membase + SP_UART_RXDMA_RD_ADR);
+
+ spin_unlock(&port->lock);
+ tty_flip_buffer_push(tty->port);
+ spin_lock(&port->lock);
+
+ value = readl(rx_dma->membase + SP_UART_RXDMA_ENABLE_SEL);
+ value |= DMA_INT;
+ writel(value, rx_dma->membase + SP_UART_RXDMA_ENABLE_SEL);
+
+ value = readl(rx_dma->membase + SP_UART_RXDMA_ENABLE_SEL);
+ value |= DMA_GO;
+ writel(value, rx_dma->membase + SP_UART_RXDMA_ENABLE_SEL);
+
+}
+
+static irqreturn_t sunplus_uart_rxdma_irq(int irq, void *args)
+{
+ struct uart_port *port = (struct uart_port *)args;
+ unsigned long flags;
+
+ spin_lock_irqsave(&port->lock, flags);
+
+ receive_chars_rxdma(port);
+
+ spin_unlock_irqrestore(&port->lock, flags);
+
+ return IRQ_HANDLED;
+}
+
+static int sunplus_startup(struct uart_port *port)
+{
+ struct sunplus_uart_port *sp_port = to_sunplus_uart(port);
+ struct sunplus_dma_info *rx_dma, *tx_dma;
+ u32 timeout, interrupt_en;
+ unsigned int ch, value;
+ int ret;
+
+ if (sp_port->uport.rs485.flags & SER_RS485_ENABLED)
+ hrtimer_cancel(&sp_port->rts_delay_after_send);
+
+#ifdef CONFIG_PM_RUNTIME_UART
+ if (port->line > 0) {
+ ret = pm_runtime_get_sync(port->dev);
+ if (ret < 0)
+ goto out;
+ }
+#endif
+
+ ret = request_irq(port->irq, sunplus_uart_irq, 0, sp_port->name, port);
+ if (ret)
+ return ret;
+
+ rx_dma = sp_port->uartdma_rx;
+
+ if (rx_dma) {
+ if (rx_dma->buf_va == NULL) {
+ /* Drop data in Rx FIFO (PIO mode) */
+ while (readl(port->membase + SP_UART_LSR) & SP_UART_LSR_RX)
+ ch = readl(port->membase + SP_UART_DATA);
+
+ rx_dma->buf_va =
+ dma_alloc_coherent(port->dev, PAGE_SIZE,
+ &(rx_dma->dma_handle), GFP_KERNEL);
+ if (rx_dma->buf_va == NULL) {
+ dev_err(port->dev, "Can't allocation buffer for %s\n",
+ sp_port->name);
+ ret = -ENOMEM;
+ goto error_01;
+ }
+
+ writel((u32)(rx_dma->dma_handle),
+ rx_dma->membase + SP_UART_RXDMA_START_ADDR);
+ writel((u32)(rx_dma->dma_handle),
+ rx_dma->membase + SP_UART_RXDMA_RD_ADR);
+
+ /* Switch clock source when setting baud rate */
+ timeout = (sp_port->pllsys_rate / 2) / 1000; /* 1 msec */
+ writel(timeout, rx_dma->membase + SP_UART_RXDMA_TIMEOUT_SET);
+
+ /*
+ * When there are only rxdma_length_thr[15:0] bytes
+ * of free buffer => Trigger interrupt
+ */
+ writel((PAGE_SIZE << 16) | (PAGE_SIZE - (PAGE_SIZE >> 3)),
+ rx_dma->membase + SP_UART_RXDMA_LENGTH_THR);
+
+ value = readl(rx_dma->membase + SP_UART_RXDMA_ENABLE_SEL);
+ value &= ~DMA_SEL_UARTX_MASK;
+ value |= (DMA_INIT | (rx_dma->which_uart << DMA_SEL_UARTX_SHIFT));
+ writel(value, rx_dma->membase + SP_UART_RXDMA_ENABLE_SEL);
+
+ value = readl(rx_dma->membase + SP_UART_RXDMA_ENABLE_SEL);
+ value &= ~DMA_INIT;
+ writel(value, rx_dma->membase + SP_UART_RXDMA_ENABLE_SEL);
+
+ value = readl(rx_dma->membase + SP_UART_RXDMA_ENABLE_SEL);
+ value |= (DMA_SW_RST_B | DMA_AUTO_ENABLE | DMA_TIMEOUT_INT_EN | DMA_ENABLE);
+ writel(value, rx_dma->membase + SP_UART_RXDMA_ENABLE_SEL);
+
+ value = readl(rx_dma->membase + SP_UART_RXDMA_ENABLE_SEL);
+ value |= DMA_GO;
+ writel(value, rx_dma->membase + SP_UART_RXDMA_ENABLE_SEL);
+ }
+
+ ret = request_irq(rx_dma->irq, sunplus_uart_rxdma_irq, 0, "UARTDMA_RX", port);
+ if (ret) {
+ dma_free_coherent(port->dev, PAGE_SIZE,
+ rx_dma->buf_va, rx_dma->dma_handle);
+ goto error_00;
+ }
+ }
+
+ tx_dma = sp_port->uartdma_tx;
+ if (tx_dma) {
+ if (tx_dma->buf_va == NULL) {
+ tx_dma->buf_va =
+ dma_alloc_coherent(port->dev, PAGE_SIZE,
+ &(tx_dma->dma_handle), GFP_KERNEL);
+ if (tx_dma->buf_va == NULL) {
+ dev_err(port->dev, "Can't allocation buffer for %s\n",
+ sp_port->name);
+ ret = -ENOMEM;
+ goto error_01;
+ }
+
+ /*
+ * set 1ms , set wr_adr , set start_addr/end_addr ,
+ * set bind to uart# , set int enable ,
+ * set txdma enable (Use ring buffer for UART's Tx)
+ */
+ writel((sp_port->pllsys_rate / 1000),
+ tx_dma->membase + SP_UART_TXDMA_TMR_UNIT);
+ writel((u32)(tx_dma->dma_handle), tx_dma->membase + SP_UART_TXDMA_WR_ADR);
+ writel((u32)(tx_dma->dma_handle),
+ tx_dma->membase + SP_UART_TXDMA_START_ADDR);
+ writel(((u32)(tx_dma->dma_handle) + PAGE_SIZE - 1),
+ tx_dma->membase + SP_UART_TXDMA_END_ADDR);
+ writel(tx_dma->which_uart, tx_dma->membase + SP_UART_TXDMA_SEL);
+ writel(0x41, tx_dma->gdma_membase + SP_UART_TXGDMA_INT_EN);
+ writel(0x00000005, tx_dma->membase + SP_UART_TXDMA_ENABLE);
+ }
+ }
+
+ /*
+ * don't need to use spin_lock_irqsave() because interrupts
+ * are globally disabled
+ */
+ spin_lock_irq(&port->lock);
+
+ /* SP_UART_ISC_TXM is enabled in .start_tx() */
+ interrupt_en = 0;
+ if (rx_dma == NULL)
+ interrupt_en |= SP_UART_ISC_RXM;
+
+ writel(interrupt_en, port->membase + SP_UART_ISC);
+
+ spin_unlock_irq(&port->lock);
+
+#ifdef CONFIG_PM_RUNTIME_UART
+ if (port->line > 0)
+ pm_runtime_put(port->dev);
+
+ return 0;
+
+out:
+ if (port->line > 0) {
+ pm_runtime_mark_last_busy(port->dev);
+ pm_runtime_put_autosuspend(port->dev);
+ }
+#endif
+ return 0;
+
+error_01:
+ if (rx_dma) {
+ dma_free_coherent(port->dev, PAGE_SIZE,
+ rx_dma->buf_va, rx_dma->dma_handle);
+ free_irq(rx_dma->irq, port);
+ }
+error_00:
+ free_irq(port->irq, port);
+ return ret;
+}
+
+static void sunplus_shutdown(struct uart_port *port)
+{
+ struct sunplus_uart_port *sp_port = to_sunplus_uart(port);
+ struct sunplus_dma_info *rx_dma;
+ unsigned int mcr, value;
+ unsigned long flags;
+
+ spin_lock_irqsave(&port->lock, flags);
+ writel(0, port->membase + SP_UART_ISC);
+ spin_unlock_irqrestore(&port->lock, flags);
+
+ free_irq(port->irq, port);
+
+ rx_dma = sp_port->uartdma_rx;
+ if (rx_dma) {
+ /* Drop whatever is still in buffer */
+ value = readl(rx_dma->membase + SP_UART_RXDMA_WR_ADR);
+ writel(value, rx_dma->membase + SP_UART_RXDMA_RD_ADR);
+
+ free_irq(rx_dma->irq, port);
+ }
+
+ /* Disable flow control of Tx, so that queued data can be sent out
+ * There is no way for s/w to let h/w abort in the middle of
+ * transaction.
+ * Don't reset module except it's in idle state. Otherwise, it might
+ * cause bus to hang.
+ */
+ mcr = readl(port->membase + SP_UART_MCR);
+ mcr &= ~SP_UART_MCR_AC;
+ writel(mcr, port->membase + SP_UART_MCR);
+
+}
+
+static void sunplus_set_termios(struct uart_port *port,
+ struct ktermios *termios, struct ktermios *oldtermios)
+{
+ u32 clk, ext, div, div_l, div_h, baud;
+ u32 lcr, mcr;
+ unsigned long flags;
+
+ clk = port->uartclk;
+
+ baud = uart_get_baud_rate(port, termios, oldtermios, 0, port->uartclk / 16);
+
+ /*
+ * Send all data in Tx FIFO before changing clock source,
+ * it should be UART0 only
+ */
+ while (!(readl(port->membase + SP_UART_LSR) & SP_UART_LSR_TXE))
+ ;
+
+ clk += baud >> 1;
+ div = clk / baud;
+ ext = div & 0x0F;
+ div = (div >> 4) - 1;
+ div_l = (div & 0xFF) | (ext << 12);
+ div_h = div >> 8;
+
+ switch (termios->c_cflag & CSIZE) {
+ case CS5:
+ lcr = SP_UART_LCR_WL5;
+ break;
+ case CS6:
+ lcr = SP_UART_LCR_WL6;
+ break;
+ case CS7:
+ lcr = SP_UART_LCR_WL7;
+ break;
+ default: /* CS8 */
+ lcr = SP_UART_LCR_WL8;
+ break;
+ }
+
+ if (termios->c_cflag & CSTOPB)
+ lcr |= SP_UART_LCR_ST;
+
+ if (termios->c_cflag & PARENB) {
+ lcr |= SP_UART_LCR_PE;
+
+ if (!(termios->c_cflag & PARODD))
+ lcr |= SP_UART_LCR_PR;
+ }
+
+ spin_lock_irqsave(&port->lock, flags);
+
+ uart_update_timeout(port, termios->c_cflag, baud);
+
+ port->read_status_mask = 0;
+ if (termios->c_iflag & INPCK)
+ port->read_status_mask |= SP_UART_LSR_PE | SP_UART_LSR_FE;
+
+ if (termios->c_iflag & (BRKINT | PARMRK))
+ port->read_status_mask |= SP_UART_LSR_BC;
+
+ /*
+ * Characters to ignore
+ */
+ port->ignore_status_mask = 0;
+ if (termios->c_iflag & IGNPAR)
+ port->ignore_status_mask |= SP_UART_LSR_FE | SP_UART_LSR_PE;
+
+ if (termios->c_iflag & IGNBRK) {
+ port->ignore_status_mask |= SP_UART_LSR_BC;
+
+ if (termios->c_iflag & IGNPAR)
+ port->ignore_status_mask |= SP_UART_LSR_OE;
+ }
+
+ /*
+ * Ignore all characters if CREAD is not set.
+ */
+ if ((termios->c_cflag & CREAD) == 0) {
+ port->ignore_status_mask |= SP_UART_CREAD_DISABLED;
+ /* flush rx data FIFO */
+ writel(0, port->membase + SP_UART_RX_RESIDUE);
+ }
+
+ mcr = readl(port->membase + SP_UART_MCR);
+
+ if (termios->c_cflag & CRTSCTS)
+ mcr |= (SP_UART_MCR_AC | SP_UART_MCR_AR);
+ else
+ mcr &= ~(SP_UART_MCR_AC | SP_UART_MCR_AR);
+
+ writel(mcr, port->membase + SP_UART_MCR);
+
+ /* do not set these in emulation */
+ writel(div_h, port->membase + SP_UART_DIV_H);
+ writel(div_l, port->membase + SP_UART_DIV_L);
+ writel(lcr, port->membase + SP_UART_LCR);
+
+ spin_unlock_irqrestore(&port->lock, flags);
+}
+
+static void sunplus_set_ldisc(struct uart_port *port,
+ struct ktermios *termios)
+{
+ int new = termios->c_line;
+
+ if (new == N_PPS) {
+ port->flags |= UPF_HARDPPS_CD;
+ sunplus_enable_ms(port);
+ } else {
+ port->flags &= ~UPF_HARDPPS_CD;
+ }
+}
+
+static const char *sunplus_type(struct uart_port *port)
+{
+ struct sunplus_uart_port *sp_port = to_sunplus_uart(port);
+
+ return sp_port->name;
+}
+
+static void sunplus_release_port(struct uart_port *port)
+{
+}
+
+static int sunplus_request_port(struct uart_port *port)
+{
+ return 0;
+}
+
+static void sunplus_config_port(struct uart_port *port, int type)
+{
+ if (type & UART_CONFIG_TYPE) {
+ port->type = PORT_SUNPLUS;
+ sunplus_request_port(port);
+ }
+}
+
+static int sunplus_verify_port(struct uart_port *port, struct serial_struct *serial)
+{
+ return -EINVAL;
+}
+
+#ifdef CONFIG_CONSOLE_POLL
+static int sunplus_poll_init(struct uart_port *port)
+{
+ return 0;
+}
+
+static void sunplus_poll_put_char(struct uart_port *port, unsigned char data)
+{
+ wait_for_xmitr(port);
+ sp_uart_put_char(port, data);
+}
+
+static int sunplus_poll_get_char(struct uart_port *port)
+{
+ unsigned int lsr;
+
+ do {
+ lsr = readl(port->membase + SP_UART_LSR);
+ } while (!(lsr & SP_UART_LSR_RX));
+
+ return readl(port->membase + SP_UART_DATA);
+}
+#endif /* CONFIG_CONSOLE_POLL */
+
+static enum hrtimer_restart sp_rts_check_tx_empty(struct hrtimer *t)
+{
+ struct sunplus_uart_port *sp_port;
+ unsigned int mcr, lsr;
+ unsigned char val;
+ ktime_t ktime;
+ unsigned long nsec;
+
+ sp_port = container_of(t, struct sunplus_uart_port, rts_check_tx_empty);
+ mcr = readl(sp_port->uport.membase + SP_UART_MCR);
+ lsr = readl(sp_port->uport.membase + SP_UART_LSR);
+ // TX is NOT empty
+ if (!(lsr & SP_UART_LSR_TXE))
+ return HRTIMER_RESTART;
+ // TX is empty
+ nsec = sp_port->uport.rs485.delay_rts_after_send * 1000000;
+ // schedule RTS set
+ if (nsec > 0) {
+ ktime = ktime_set(0, nsec);
+ hrtimer_start(&sp_port->rts_delay_after_send, ktime, HRTIMER_MODE_REL);
+ return HRTIMER_NORESTART;
+ }
+ // immediately set RTS
+ val = (sp_port->uport.rs485.flags & SER_RS485_RTS_AFTER_SEND ? 1 : 0);
+ if (sp_port->uport.rs485.flags & SER_RS485_RTS_ON_SEND)
+ mcr |= SP_UART_MCR_RTS;
+ else
+ mcr &= ~SP_UART_MCR_RTS;
+ if (sp_port->uport.rs485.flags & SER_RS485_ENABLED && !IS_ERR(sp_port->rts_gpio)) {
+ gpiod_set_value(sp_port->rts_gpio, val);
+ dev_dbg(sp_port->uport.dev, "%s set rts_gpio=%d\n",
+ sp_port->uport.name, val);
+ } else
+ writel(mcr, sp_port->uport.membase + SP_UART_MCR);
+
+ return HRTIMER_NORESTART;
+}
+
+static enum hrtimer_restart sp_rts_delay_before_send(struct hrtimer *t)
+{
+ struct sunplus_uart_port *sp_port;
+ ktime_t ktime;
+
+ sp_port = container_of(t, struct sunplus_uart_port, rts_delay_before_send);
+ ktime = ktime_set(0, 500000); //500us
+ hrtimer_start(&sp_port->rts_check_tx_empty, ktime, HRTIMER_MODE_REL);
+ __start_tx(&sp_port->uport);
+ return HRTIMER_NORESTART;
+}
+
+static enum hrtimer_restart sp_rts_delay_after_send(struct hrtimer *t)
+{
+ struct sunplus_uart_port *sp_port;
+ unsigned char val;
+ unsigned int mcr;
+
+ sp_port = container_of(t, struct sunplus_uart_port, rts_delay_after_send);
+ mcr = readl(sp_port->uport.membase + SP_UART_MCR);
+
+ val = (sp_port->uport.rs485.flags & SER_RS485_RTS_AFTER_SEND ? 1 : 0);
+ if (sp_port->uport.rs485.flags & SER_RS485_RTS_ON_SEND)
+ mcr |= SP_UART_MCR_RTS;
+ else
+ mcr &= ~SP_UART_MCR_RTS;
+ if (sp_port->uport.rs485.flags & SER_RS485_ENABLED && !IS_ERR(sp_port->rts_gpio)) {
+ gpiod_set_value(sp_port->rts_gpio, val);
+ dev_dbg(sp_port->uport.dev, "%s set rts_gpio=%d\n",
+ sp_port->uport.name, val);
+ } else
+ writel(mcr, sp_port->uport.membase + SP_UART_MCR);
+
+ return HRTIMER_NORESTART;
+}
+
+static int sunplus_uart_rs485_on(struct uart_port *port)
+{
+ struct sunplus_uart_port *sp_port = to_sunplus_uart(port);
+
+ if (IS_ERR(sp_port->rts_gpio)) {
+ dev_err(port->dev, "%s No valid rts_gpio, disabling 485\n",
+ port->name);
+ port->rs485.flags &= ~SER_RS485_ENABLED;
+ return (-EINVAL);
+ }
+
+ if (!sp_port->rts_check_tx_empty.function) {
+ hrtimer_init(&(sp_port->rts_check_tx_empty), CLOCK_MONOTONIC, HRTIMER_MODE_REL);
+ sp_port->rts_check_tx_empty.function = sp_rts_check_tx_empty;
+ }
+ if (!sp_port->rts_delay_before_send.function) {
+ hrtimer_init(&(sp_port->rts_delay_before_send), CLOCK_MONOTONIC, HRTIMER_MODE_REL);
+ sp_port->rts_delay_before_send.function = sp_rts_delay_before_send;
+ }
+ if (!sp_port->rts_delay_after_send.function) {
+ hrtimer_init(&(sp_port->rts_delay_after_send), CLOCK_MONOTONIC, HRTIMER_MODE_REL);
+ sp_port->rts_delay_after_send.function = sp_rts_delay_after_send;
+ }
+ return (0);
+}
+
+static int sunplus_uart_rs485_off(struct uart_port *port)
+{
+ struct sunplus_uart_port *sp_port = to_sunplus_uart(port);
+
+ port->rs485.flags &= ~SER_RS485_ENABLED;
+ if (sp_port->rts_check_tx_empty.function) {
+ hrtimer_cancel(&sp_port->rts_check_tx_empty);
+ sp_port->rts_check_tx_empty.function = NULL;
+ }
+ if (sp_port->rts_delay_before_send.function) {
+ hrtimer_cancel(&sp_port->rts_delay_before_send);
+ sp_port->rts_delay_before_send.function = NULL;
+ }
+ if (sp_port->rts_delay_after_send.function) {
+ hrtimer_cancel(&sp_port->rts_delay_after_send);
+ sp_port->rts_delay_after_send.function = NULL;
+ }
+ return (0);
+}
+
+static int sunplus_uart_config_rs485(struct uart_port *port,
+ struct serial_rs485 *rs485)
+{
+ struct sunplus_uart_port *sp_port = to_sunplus_uart(port);
+ int val;
+
+ if (IS_ERR(sp_port->rts_gpio)) {
+ dev_err(port->dev, "%s No valid rts_gpio - skipping rs485\n",
+ port->name);
+ port->rs485.flags &= ~SER_RS485_ENABLED;
+ return (-EINVAL);
+ }
+
+#ifdef CONFIG_PM_RUNTIME_UART
+ pm_runtime_get_sync(sp_port->dev);
+#endif
+
+ rs485->delay_rts_before_send =
+ min(rs485->delay_rts_before_send, 10000U);
+ rs485->delay_rts_after_send =
+ min(rs485->delay_rts_after_send, 10000U);
+
+ if (rs485->flags & SER_RS485_ENABLED) {
+ sunplus_uart_rs485_on(port);
+ val = (rs485->flags & SER_RS485_RTS_AFTER_SEND ? 1 : 0);
+ gpiod_set_value(sp_port->rts_gpio, val);
+ } else
+ sunplus_uart_rs485_off(port);
+
+ port->rs485 = *rs485;
+
+#ifdef CONFIG_PM_RUNTIME_UART
+ pm_runtime_mark_last_busy(sp_port->dev);
+ pm_runtime_put_autosuspend(sp_port->dev);
+#endif
+ return (0);
+}
+
+static const struct uart_ops sunplus_uart_ops = {
+ .tx_empty = sunplus_tx_empty,
+ .set_mctrl = sunplus_set_mctrl,
+ .get_mctrl = sunplus_get_mctrl,
+ .stop_tx = sunplus_stop_tx,
+ .start_tx = sunplus_start_tx,
+ .stop_rx = sunplus_stop_rx,
+ .enable_ms = sunplus_enable_ms,
+ .break_ctl = sunplus_break_ctl,
+ .startup = sunplus_startup,
+ .shutdown = sunplus_shutdown,
+ .set_termios = sunplus_set_termios,
+ .set_ldisc = sunplus_set_ldisc,
+ .type = sunplus_type,
+ .release_port = sunplus_release_port,
+ .request_port = sunplus_request_port,
+ .config_port = sunplus_config_port,
+ .verify_port = sunplus_verify_port,
+#ifdef CONFIG_CONSOLE_POLL
+ .poll_init = sunplus_poll_init,
+ .poll_put_char = sunplus_poll_put_char,
+ .poll_get_char = sunplus_poll_get_char,
+#endif /* CONFIG_CONSOLE_POLL */
+};
+
+#ifdef CONFIG_SERIAL_SUNPLUS_CONSOLE
+static void sunplus_uart_console_putchar(struct uart_port *port, int ch)
+{
+ wait_for_xmitr(port);
+ sp_uart_put_char(port, ch);
+}
+
+static void sunplus_console_write(struct console *co,
+ const char *s, unsigned int count)
+{
+ unsigned long flags;
+ int locked = 1;
+
+ local_irq_save(flags);
+
+ if (sunplus_uart_ports[co->index].uport.sysrq)
+ locked = 0;
+ else if (oops_in_progress)
+ locked = spin_trylock(&sunplus_uart_ports[co->index].uport.lock);
+ else
+ spin_lock(&sunplus_uart_ports[co->index].uport.lock);
+
+ uart_console_write(&sunplus_uart_ports[co->index].uport,
+ s, count, sunplus_uart_console_putchar);
+
+ if (locked)
+ spin_unlock(&sunplus_uart_ports[co->index].uport.lock);
+
+ local_irq_restore(flags);
+}
+
+static int __init sunplus_console_setup(struct console *co, char *options)
+{
+ struct uart_port *port;
+ int baud = 115200;
+ int bits = 8;
+ int parity = 'n';
+ int flow = 'n';
+
+ if ((co->index >= UART_NR) || (co->index < 0))
+ return -EINVAL;
+
+ port = &sunplus_uart_ports[co->index].uport;
+
+ if (options)
+ uart_parse_options(options, &baud, &parity, &bits, &flow);
+
+ return uart_set_options(port, co, baud, parity, bits, flow);
+}
+
+static struct console sunplus_console = {
+ .name = "ttyS",
+ .write = sunplus_console_write,
+ .device = uart_console_device,
+ .setup = sunplus_console_setup,
+ .flags = CON_PRINTBUFFER,
+ .index = -1,
+ .data = &sunplus_uart_driver
+};
+#endif
+
+static struct uart_driver sunplus_uart_driver = {
+ .owner = THIS_MODULE,
+ .driver_name = "Sunplus_UART",
+ .dev_name = "ttyS",
+ .major = TTY_MAJOR,
+ .minor = 64,
+ .nr = UART_NR,
+#ifdef CONFIG_SERIAL_SUNPLUS_CONSOLE
+ .cons = &sunplus_console
+#endif
+};
+
+static int sunplus_uart_probe(struct platform_device *pdev)
+{
+ struct resource *res_mem;
+ struct uart_port *port;
+ struct clk *clk, *pllsys;
+ unsigned int pllsys_rate;
+ int ret, irq;
+ int idx_offset, idx;
+ int idx_which_uart;
+ char peri_name[16];
+
+ if (pdev->dev.of_node) {
+ pdev->id = of_alias_get_id(pdev->dev.of_node, "serial");
+ if (pdev->id < 0)
+ pdev->id = of_alias_get_id(pdev->dev.of_node, "uart");
+ }
+
+ idx_offset = -1;
+
+ if (IS_UARTDMARX_ID(pdev->id))
+ idx_offset = 0;
+ else if (IS_UARTDMATX_ID(pdev->id))
+ idx_offset = UART_DMARX_NR;
+
+ /* init txdma or rxdma */
+ if (idx_offset >= 0) {
+ clk = devm_clk_get(&pdev->dev, NULL);
+ if (IS_ERR(clk))
+ return PTR_ERR(clk);
+
+ ret = clk_prepare_enable(clk);
+ if (ret)
+ return ret;
+
+ if (idx_offset == 0)
+ idx = idx_offset + pdev->id - ID_BASE_DMARX;
+ else
+ idx = idx_offset + pdev->id - ID_BASE_DMATX;
+
+ res_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!res_mem)
+ return -ENODEV;
+
+ sprintf(peri_name, "PERI%d", (idx & 0x01));
+
+ clk = devm_clk_get(&pdev->dev, peri_name);
+ if (IS_ERR(clk))
+ return PTR_ERR(clk);
+
+ ret = clk_prepare_enable(clk);
+ if (ret)
+ return ret;
+
+ sunplus_uartdma[idx].addr_phy =
+ (unsigned long)(res_mem->start);
+ sunplus_uartdma[idx].membase =
+ devm_ioremap_resource(&pdev->dev, res_mem);
+
+ if (IS_ERR(sunplus_uartdma[idx].membase))
+ return PTR_ERR(sunplus_uartdma[idx].membase);
+
+ if (IS_UARTDMARX_ID(pdev->id)) {
+ irq = platform_get_irq(pdev, 0);
+ if (irq < 0)
+ return -ENODEV;
+
+ sunplus_uartdma[idx].irq = irq;
+ } else {
+ res_mem = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+ if (!res_mem)
+ return -ENODEV;
+
+ sunplus_uartdma[idx].gdma_membase =
+ devm_ioremap_resource(&pdev->dev, res_mem);
+
+ if (IS_ERR(sunplus_uartdma[idx].gdma_membase))
+ return -EINVAL;
+ }
+
+ if (of_property_read_u32(pdev->dev.of_node, "which-uart", &idx_which_uart) != 0) {
+ dev_err(&pdev->dev, "\"which-uart\" is not assigned.");
+ return -EINVAL;
+ }
+
+ if (idx_which_uart >= UART_NR) {
+ dev_err(&pdev->dev, "\"which-uart\" is not valid.");
+ return -EINVAL;
+ }
+
+ sunplus_uartdma[idx].which_uart = idx_which_uart;
+
+ return 0;
+ } else if (pdev->id < 0 || pdev->id >= UART_NR)
+ return -EINVAL;
+
+ /* init uart */
+ port = &sunplus_uart_ports[pdev->id].uport;
+ if (port->membase)
+ return -EBUSY;
+
+ memset(port, 0, sizeof(*port));
+
+ res_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!res_mem)
+ return -ENODEV;
+
+ port->dev = &pdev->dev;
+ port->mapbase = res_mem->start;
+
+ port->membase = devm_ioremap_resource(&pdev->dev, res_mem);
+ if (IS_ERR(port->membase))
+ return PTR_ERR(port->membase);
+
+ irq = platform_get_irq(pdev, 0);
+ if (irq < 0)
+ return -ENODEV;
+
+ uart_get_rs485_mode(port);
+ sunplus_uart_ports[pdev->id].rts_gpio =
+ devm_gpiod_get(&pdev->dev, "rts", GPIOD_OUT_LOW);
+ port->rs485_config = sunplus_uart_config_rs485;
+ sunplus_uart_ports[pdev->id].rts_check_tx_empty.function = NULL;
+ sunplus_uart_ports[pdev->id].rts_delay_before_send.function = NULL;
+ sunplus_uart_ports[pdev->id].rts_delay_after_send.function = NULL;
+ if (port->rs485.flags & SER_RS485_ENABLED)
+ sunplus_uart_rs485_on(port);
+
+ sunplus_uart_ports[pdev->id].clk = devm_clk_get(&pdev->dev, NULL);
+ if (IS_ERR(sunplus_uart_ports[pdev->id].clk))
+ return PTR_ERR(sunplus_uart_ports[pdev->id].clk);
+
+ ret = clk_prepare_enable(sunplus_uart_ports[pdev->id].clk);
+ if (ret)
+ return ret;
+
+ sunplus_uart_ports[pdev->id].rstc =
+ devm_reset_control_get(&pdev->dev, NULL);
+
+ if (IS_ERR(sunplus_uart_ports[pdev->id].rstc))
+ return PTR_ERR(sunplus_uart_ports[pdev->id].rstc);
+
+ ret = reset_control_deassert(sunplus_uart_ports[pdev->id].rstc);
+ if (ret)
+ return ret;
+
+ clk = sunplus_uart_ports[pdev->id].clk;
+ if (IS_ERR(clk))
+ port->uartclk = XTAL;
+ else
+ port->uartclk = clk_get_rate(clk);
+
+ pllsys = clk_get_sys("pllsys", NULL);
+ pllsys_rate = clk_get_rate(pllsys);
+
+ sunplus_uart_ports[pdev->id].pllsys_rate = pllsys_rate;
+
+ port->iotype = UPIO_MEM;
+ port->irq = irq;
+ port->ops = &sunplus_uart_ops;
+ port->flags = UPF_BOOT_AUTOCONF;
+ port->fifosize = 128;
+ port->line = pdev->id;
+
+#ifdef CONFIG_SERIAL_SUNPLUS_CONSOLE
+ if (pdev->id == 0)
+ port->cons = &sunplus_console;
+#endif
+
+ port->private_data = container_of(&sunplus_uart_ports[pdev->id].uport,
+ struct sunplus_uart_port, uport);
+
+ sprintf(sunplus_uart_ports[pdev->id].name, "sp_uart%d", pdev->id);
+
+ sunplus_uart_ports[pdev->id].uartdma_rx =
+ sunplus_uartdma_rx_binding(pdev->id);
+
+ if (sunplus_uart_ports[pdev->id].uartdma_rx)
+ dev_info(port->dev, "%s's Rx is in DMA mode.\n",
+ sunplus_uart_ports[pdev->id].name);
+ else
+ dev_info(port->dev, "%s's Rx is in PIO mode.\n",
+ sunplus_uart_ports[pdev->id].name);
+
+ sunplus_uart_ports[pdev->id].uartdma_tx =
+ sunplus_uartdma_tx_binding(pdev->id);
+
+ if (sunplus_uart_ports[pdev->id].uartdma_tx)
+ dev_info(port->dev, "%s's Tx is in DMA mode.\n",
+ sunplus_uart_ports[pdev->id].name);
+ else
+ dev_info(port->dev, "%s's Tx is in PIO mode.\n",
+ sunplus_uart_ports[pdev->id].name);
+
+ ret = uart_add_one_port(&sunplus_uart_driver, port);
+ if (ret) {
+ port->membase = NULL;
+ return ret;
+ }
+ platform_set_drvdata(pdev, port);
+
+#ifdef CONFIG_PM_RUNTIME_UART
+ if (pdev->id != 0) {
+ pm_runtime_set_autosuspend_delay(&pdev->dev, 5000);
+ pm_runtime_use_autosuspend(&pdev->dev);
+ pm_runtime_set_active(&pdev->dev);
+ pm_runtime_enable(&pdev->dev);
+ }
+#endif
+ return 0;
+}
+
+static int sunplus_uart_remove(struct platform_device *pdev)
+{
+#ifdef CONFIG_PM_RUNTIME_UART
+ if (pdev->id != 0) {
+ pm_runtime_disable(&pdev->dev);
+ pm_runtime_set_suspended(&pdev->dev);
+ }
+#endif
+ uart_remove_one_port(&sunplus_uart_driver,
+ &sunplus_uart_ports[pdev->id].uport);
+
+ if (pdev->id < UART_NR) {
+ clk_disable_unprepare(sunplus_uart_ports[pdev->id].clk);
+ reset_control_assert(sunplus_uart_ports[pdev->id].rstc);
+ }
+
+ return 0;
+}
+
+static int sunplus_uart_suspend(struct platform_device *pdev,
+ pm_message_t state)
+{
+ /* Don't suspend uart0 for cmd line usage */
+ if ((pdev->id < UART_NR) && (pdev->id > 0))
+ reset_control_assert(sunplus_uart_ports[pdev->id].rstc);
+
+ return 0;
+}
+
+static int sunplus_uart_resume(struct platform_device *pdev)
+{
+ if (pdev->id < UART_NR) {
+ clk_prepare_enable(sunplus_uart_ports[pdev->id].clk);
+ reset_control_deassert(sunplus_uart_ports[pdev->id].rstc);
+ }
+ return 0;
+}
+
+static const struct of_device_id sp_uart_of_match[] = {
+ { .compatible = "sunplus,sp7021-uart" },
+ { .compatible = "sunplus,sp7021-uart-rxdma" },
+ { .compatible = "sunplus,sp7021-uart-txdma" },
+ {}
+};
+MODULE_DEVICE_TABLE(of, sp_uart_of_match);
+
+#ifdef CONFIG_PM_RUNTIME_UART
+static int sunplus_uart_runtime_suspend(struct device *dev)
+{
+ struct platform_device *pdev = to_platform_device(dev);
+
+ /* Don't suspend uart0 for cmd line usage */
+ if ((pdev->id < UART_NR) && (pdev->id > 0))
+ reset_control_assert(sunplus_uart_ports[pdev->id].rstc);
+
+ return 0;
+}
+
+static int sunplus_uart_runtime_resume(struct device *dev)
+{
+ struct platform_device *pdev = to_platform_device(dev);
+
+ if (pdev->id < UART_NR) {
+ clk_prepare_enable(sunplus_uart_ports[pdev->id].clk);
+ reset_control_deassert(sunplus_uart_ports[pdev->id].rstc);
+ }
+
+ return 0;
+}
+static const struct dev_pm_ops sp7021_uart_pm_ops = {
+ .runtime_suspend = sunplus_uart_runtime_suspend,
+ .runtime_resume = sunplus_uart_runtime_resume,
+};
+#define sunplus_uart_pm_ops (&sp7021_uart_pm_ops)
+#endif
+
+static struct platform_driver sunplus_uart_platform_driver = {
+ .probe = sunplus_uart_probe,
+ .remove = sunplus_uart_remove,
+ .suspend = sunplus_uart_suspend,
+ .resume = sunplus_uart_resume,
+ .driver = {
+ .name = "sunplus-uart",
+ .owner = THIS_MODULE,
+ .of_match_table = of_match_ptr(sp_uart_of_match),
+#ifdef CONFIG_PM_RUNTIME_UART
+ .pm = sunplus_uart_pm_ops,
+#endif
+ }
+};
+
+static int __init sunplus_uart_init(void)
+{
+ int ret;
+
+ memset(sunplus_uart_ports, 0, sizeof(sunplus_uart_ports));
+ memset(sunplus_uartdma, 0, sizeof(sunplus_uartdma));
+
+ if (!uart0_as_console || !(uart_enable_status & 0x01))
+ sunplus_uart_driver.cons = NULL;
+
+ /* /proc/tty/driver/(sunplus_uart_driver->driver_name) */
+ ret = uart_register_driver(&sunplus_uart_driver);
+ if (ret < 0)
+ return ret;
+
+ ret = platform_driver_register(&sunplus_uart_platform_driver);
+ if (ret != 0) {
+ uart_unregister_driver(&sunplus_uart_driver);
+ return ret;
+ }
+
+ return 0;
+}
+module_init(sunplus_uart_init);
+
+module_param(uart0_as_console, uint, 0444);
+
+#ifdef CONFIG_SERIAL_EARLYCON
+static void sunplus_uart_putc(struct uart_port *port, int c)
+{
+ unsigned int status;
+
+ for (;;) {
+ status = readl(port->membase + SP_UART_LSR);
+ if ((status & SP_UART_LSR_TXE) == SP_UART_LSR_TXE)
+ break;
+ cpu_relax();
+ }
+ writel(c, port->membase + SP_UART_DATA);
+}
+
+static void sunplus_uart_early_write(struct console *con,
+ const char *s, unsigned int n)
+{
+ struct earlycon_device *dev = con->data;
+
+ uart_console_write(&dev->port, s, n, sunplus_uart_putc);
+}
+
+int __init sunplus_uart_early_setup(struct earlycon_device *device,
+ const char *opt)
+{
+ if (!(device->port.membase || device->port.iobase))
+ return -ENODEV;
+
+ device->con->write = sunplus_uart_early_write;
+ return 0;
+}
+OF_EARLYCON_DECLARE(sunplus_uart, "sunplus,sp7021-uart", sunplus_uart_early_setup);
+#endif
+
+MODULE_DESCRIPTION("Sunplus UART driver");
+MODULE_AUTHOR("Hammer Hsieh <hammer.hsieh@sunplus.com>");
+MODULE_LICENSE("GPL v2");
diff --git a/include/soc/sunplus/sp_uart.h b/include/soc/sunplus/sp_uart.h
new file mode 100644
index 0000000..44bc1fb
--- /dev/null
+++ b/include/soc/sunplus/sp_uart.h
@@ -0,0 +1,147 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Sunplus SoC UART driver header file
+ */
+
+#ifndef __SP_UART_H__
+#define __SP_UART_H__
+
+#ifdef CONFIG_DEBUG_SP_UART
+#include <mach/io_map.h>
+
+#define LL_UART_PADDR PA_IOB_ADDR(18 * 32 * 4)
+#define LL_UART_VADDR VA_IOB_ADDR(18 * 32 * 4)
+#define LOGI_ADDR_UART0_REG VA_IOB_ADDR(18 * 32 * 4)
+#endif
+
+/*
+ * UART REG
+ *
+ */
+#define SP_UART_DATA 0x00
+#define SP_UART_LSR 0x04
+#define SP_UART_MSR 0x08
+#define SP_UART_LCR 0x0C
+#define SP_UART_MCR 0x10
+#define SP_UART_DIV_L 0x14
+#define SP_UART_DIV_H 0x18
+#define SP_UART_ISC 0x1C
+#define SP_UART_TX_RESIDUE 0x20
+#define SP_UART_RX_RESIDUE 0x24
+
+/* lsr
+ * 1: trasmit fifo is empty
+ */
+#define SP_UART_LSR_TXE (1 << 6)
+
+/* interrupt
+ * SP_UART_LSR_BC : break condition
+ * SP_UART_LSR_FE : frame error
+ * SP_UART_LSR_OE : overrun error
+ * SP_UART_LSR_PE : parity error
+ * SP_UART_LSR_RX : 1: receive fifo not empty
+ * SP_UART_LSR_TX : 1: transmit fifo is not full
+ */
+#define SP_UART_CREAD_DISABLED (1 << 16)
+#define SP_UART_LSR_BC (1 << 5)
+#define SP_UART_LSR_FE (1 << 4)
+#define SP_UART_LSR_OE (1 << 3)
+#define SP_UART_LSR_PE (1 << 2)
+#define SP_UART_LSR_RX (1 << 1)
+#define SP_UART_LSR_TX (1 << 0)
+
+#define SP_UART_LSR_BRK_ERROR_BITS \
+ (SP_UART_LSR_PE | SP_UART_LSR_OE | SP_UART_LSR_FE | SP_UART_LSR_BC)
+
+/* lcr */
+#define SP_UART_LCR_WL5 (0 << 0)
+#define SP_UART_LCR_WL6 (1 << 0)
+#define SP_UART_LCR_WL7 (2 << 0)
+#define SP_UART_LCR_WL8 (3 << 0)
+#define SP_UART_LCR_ST (1 << 2)
+#define SP_UART_LCR_PE (1 << 3)
+#define SP_UART_LCR_PR (1 << 4)
+#define SP_UART_LCR_BC (1 << 5)
+
+/* isc
+ * SP_UART_ISC_MSM : Modem status ctrl
+ * SP_UART_ISC_LSM : Line status interrupt
+ * SP_UART_ISC_RXM : RX interrupt, when got some input data
+ * SP_UART_ISC_TXM : TX interrupt, when trans start
+ */
+#define SP_UART_ISC_MSM (1 << 7)
+#define SP_UART_ISC_LSM (1 << 6)
+#define SP_UART_ISC_RXM (1 << 5)
+#define SP_UART_ISC_TXM (1 << 4)
+#define HAS_UART_ISC_FLAGMASK 0x0F
+#define SP_UART_ISC_MS (1 << 3)
+#define SP_UART_ISC_LS (1 << 2)
+#define SP_UART_ISC_RX (1 << 1)
+#define SP_UART_ISC_TX (1 << 0)
+
+/* modem control register */
+#define SP_UART_MCR_AT (1 << 7)
+#define SP_UART_MCR_AC (1 << 6)
+#define SP_UART_MCR_AR (1 << 5)
+#define SP_UART_MCR_LB (1 << 4)
+#define SP_UART_MCR_RI (1 << 3)
+#define SP_UART_MCR_DCD (1 << 2)
+#define SP_UART_MCR_RTS (1 << 1)
+#define SP_UART_MCR_DTS (1 << 0)
+
+/*
+ * RX DMA REG
+ *
+ */
+#define SP_UART_RXDMA_ENABLE_SEL 0x00
+#define DMA_INT (1 << 31)
+#define DMA_MSI_ID_SHIFT 12
+#define DMA_MSI_ID_MASK (0x7F << DMA_MSI_ID_SHIFT)
+#define DMA_SEL_UARTX_SHIFT 8
+#define DMA_SEL_UARTX_MASK (0x07 << DMA_SEL_UARTX_SHIFT)
+#define DMA_SW_RST_B (1 << 7)
+#define DMA_INIT (1 << 6)
+#define DMA_GO (1 << 5)
+#define DMA_AUTO_ENABLE (1 << 4)
+#define DMA_TIMEOUT_INT_EN (1 << 3)
+#define DMA_P_SAFE_DISABLE (1 << 2)
+#define DMA_PBUS_DATA_SWAP (1 << 1)
+#define DMA_ENABLE (1 << 0)
+#define SP_UART_RXDMA_START_ADDR 0x04
+#define SP_UART_RXDMA_TIMEOUT_SET 0x08
+#define SP_UART_RXDMA_WR_ADR 0x10
+#define SP_UART_RXDMA_RD_ADR 0x14
+#define SP_UART_RXDMA_LENGTH_THR 0x18
+#define SP_UART_RXDMA_END_ADDR 0x1C
+#define SP_UART_RXDMA_DATABYTES 0x20
+#define SP_UART_RXDMA_DEBUG_INFO 0x24
+/*
+ * TX DMA REG
+ *
+ */
+#define SP_UART_TXDMA_ENABLE 0x00
+#define SP_UART_TXDMA_SEL 0x04
+#define SP_UART_TXDMA_START_ADDR 0x08
+#define SP_UART_TXDMA_END_ADDR 0x0C
+#define SP_UART_TXDMA_WR_ADR 0x10
+#define SP_UART_TXDMA_RD_ADR 0x14
+#define SP_UART_TXDMA_STATUS 0x18
+#define TXDMA_BUF_FULL 0x01
+#define TXDMA_BUF_EMPTY 0x02
+#define SP_UART_TXDMA_TMR_UNIT 0x1C
+#define SP_UART_TXDMA_TMR_CNT 0x20
+#define SP_UART_TXDMA_RST_DONE 0x24
+/*
+ * TX GDMA REG
+ *
+ */
+#define SP_UART_TXGDMA_HW_VER 0x00
+#define SP_UART_TXGDMA_CONFIG 0x04
+#define SP_UART_TXGDMA_LENGTH 0x08
+#define SP_UART_TXGDMA_ADDR 0x0C
+#define SP_UART_TXGDMA_PORT_MUX 0x10
+#define SP_UART_TXGDMA_INT_FLAG 0x14
+#define SP_UART_TXGDMA_INT_EN 0x18
+#define SP_UART_TXGDMA_SOFT_RESET_STATUS 0x1C
+
+#endif /* __SP_UART_H__ */
--
2.7.4
^ permalink raw reply related [flat|nested] 19+ messages in thread
* Re: [PATCH v2 2/2] serial:sunplus-uart:Add Sunplus SoC UART Driver
2021-11-10 7:51 ` [PATCH v2 2/2] serial:sunplus-uart:Add " Hammer Hsieh
@ 2021-11-10 9:50 ` Philipp Zabel
2021-11-11 9:45 ` Hammer Hsieh 謝宏孟
2021-11-12 8:31 ` kernel test robot
1 sibling, 1 reply; 19+ messages in thread
From: Philipp Zabel @ 2021-11-10 9:50 UTC (permalink / raw)
To: Hammer Hsieh, gregkh, robh+dt, linux-serial, devicetree,
linux-kernel, jirislaby
Cc: tony.huang, wells.lu, Hammer Hsieh
Hi,
On Wed, 2021-11-10 at 15:51 +0800, Hammer Hsieh wrote:
[...]
> +struct sunplus_uart_port {
> + char name[16];
> + struct uart_port uport;
> + struct sunplus_dma_info *uartdma_rx;
> + struct sunplus_dma_info *uartdma_tx;
> + struct clk *clk;
> + struct reset_control *rstc;
> + unsigned int pllsys_rate;
> + struct gpio_desc *rts_gpio;
> + struct hrtimer rts_check_tx_empty;
> + struct hrtimer rts_delay_before_send;
> + struct hrtimer rts_delay_after_send;
> +};
> +struct sunplus_uart_port sunplus_uart_ports[UART_NR];
Does this have to be a global array? I would expect these to be
allocated in the probe function, one at a time.
[...]
> +static int sunplus_uart_probe(struct platform_device *pdev)
> +{
> + struct resource *res_mem;
> + struct uart_port *port;
> + struct clk *clk, *pllsys;
> + unsigned int pllsys_rate;
> + int ret, irq;
> + int idx_offset, idx;
> + int idx_which_uart;
> + char peri_name[16];
> +
> + if (pdev->dev.of_node) {
> + pdev->id = of_alias_get_id(pdev->dev.of_node, "serial");
> + if (pdev->id < 0)
> + pdev->id = of_alias_get_id(pdev->dev.of_node, "uart");
> + }
> +
> + idx_offset = -1;
> +
> + if (IS_UARTDMARX_ID(pdev->id))
> + idx_offset = 0;
> + else if (IS_UARTDMATX_ID(pdev->id))
> + idx_offset = UART_DMARX_NR;
> +
> + /* init txdma or rxdma */
> + if (idx_offset >= 0) {
> + clk = devm_clk_get(&pdev->dev, NULL);
Should this be requested by name? Looking at the binding, this could be
UADMA or HWUA?
> + if (IS_ERR(clk))
> + return PTR_ERR(clk);
> +
> + ret = clk_prepare_enable(clk);
> + if (ret)
> + return ret;
I suggest to move this down after all required resources are available.
Otherwise you'll have to either disable the clock in the error paths, or
you are left with a running clock if anything below fails.
> + if (idx_offset == 0)
> + idx = idx_offset + pdev->id - ID_BASE_DMARX;
> + else
> + idx = idx_offset + pdev->id - ID_BASE_DMATX;
> +
> + res_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + if (!res_mem)
> + return -ENODEV;
> +
> + sprintf(peri_name, "PERI%d", (idx & 0x01));
> +
> + clk = devm_clk_get(&pdev->dev, peri_name);
> + if (IS_ERR(clk))
> + return PTR_ERR(clk);
> +
> + ret = clk_prepare_enable(clk);
Same as above.
> + if (ret)
> + return ret;
> +
> + sunplus_uartdma[idx].addr_phy =
> + (unsigned long)(res_mem->start);
> + sunplus_uartdma[idx].membase =
> + devm_ioremap_resource(&pdev->dev, res_mem);
> +
> + if (IS_ERR(sunplus_uartdma[idx].membase))
> + return PTR_ERR(sunplus_uartdma[idx].membase);
> +
> + if (IS_UARTDMARX_ID(pdev->id)) {
> + irq = platform_get_irq(pdev, 0);
> + if (irq < 0)
> + return -ENODEV;
> +
> + sunplus_uartdma[idx].irq = irq;
> + } else {
> + res_mem = platform_get_resource(pdev, IORESOURCE_MEM, 1);
> + if (!res_mem)
> + return -ENODEV;
> +
> + sunplus_uartdma[idx].gdma_membase =
> + devm_ioremap_resource(&pdev->dev, res_mem);
> +
> + if (IS_ERR(sunplus_uartdma[idx].gdma_membase))
> + return -EINVAL;
> + }
> +
> + if (of_property_read_u32(pdev->dev.of_node, "which-uart", &idx_which_uart) != 0) {
> + dev_err(&pdev->dev, "\"which-uart\" is not assigned.");
> + return -EINVAL;
> + }
> +
> + if (idx_which_uart >= UART_NR) {
> + dev_err(&pdev->dev, "\"which-uart\" is not valid.");
> + return -EINVAL;
> + }
> +
> + sunplus_uartdma[idx].which_uart = idx_which_uart;
> +
> + return 0;
> + } else if (pdev->id < 0 || pdev->id >= UART_NR)
> + return -EINVAL;
> +
> + /* init uart */
> + port = &sunplus_uart_ports[pdev->id].uport;
> + if (port->membase)
> + return -EBUSY;
> +
> + memset(port, 0, sizeof(*port));
> +
> + res_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + if (!res_mem)
> + return -ENODEV;
> +
> + port->dev = &pdev->dev;
> + port->mapbase = res_mem->start;
> +
> + port->membase = devm_ioremap_resource(&pdev->dev, res_mem);
> + if (IS_ERR(port->membase))
> + return PTR_ERR(port->membase);
> +
> + irq = platform_get_irq(pdev, 0);
> + if (irq < 0)
> + return -ENODEV;
> +
> + uart_get_rs485_mode(port);
> + sunplus_uart_ports[pdev->id].rts_gpio =
> + devm_gpiod_get(&pdev->dev, "rts", GPIOD_OUT_LOW);
> + port->rs485_config = sunplus_uart_config_rs485;
> + sunplus_uart_ports[pdev->id].rts_check_tx_empty.function = NULL;
> + sunplus_uart_ports[pdev->id].rts_delay_before_send.function = NULL;
> + sunplus_uart_ports[pdev->id].rts_delay_after_send.function = NULL;
> + if (port->rs485.flags & SER_RS485_ENABLED)
> + sunplus_uart_rs485_on(port);
> +
> + sunplus_uart_ports[pdev->id].clk = devm_clk_get(&pdev->dev, NULL);
Here the same nameless clock as in the loop above is requested again.
Should this be UADMA or HWUA?
> + if (IS_ERR(sunplus_uart_ports[pdev->id].clk))
> + return PTR_ERR(sunplus_uart_ports[pdev->id].clk);
> +
> + ret = clk_prepare_enable(sunplus_uart_ports[pdev->id].clk);
> + if (ret)
> + return ret;
Same comment as above. Better to request the reset control before
enabling the clock, for example.
> +
> + sunplus_uart_ports[pdev->id].rstc =
> + devm_reset_control_get(&pdev->dev, NULL);
Please use devm_reset_control_get_exclusive() instead.
> +
> + if (IS_ERR(sunplus_uart_ports[pdev->id].rstc))
> + return PTR_ERR(sunplus_uart_ports[pdev->id].rstc);
> +
> + ret = reset_control_deassert(sunplus_uart_ports[pdev->id].rstc);
> + if (ret)
> + return ret;
> +
> + clk = sunplus_uart_ports[pdev->id].clk;
> + if (IS_ERR(clk))
This can't ever be true, the code above already returned in this case.
[...]
> +static int sunplus_uart_remove(struct platform_device *pdev)
> +{
> +#ifdef CONFIG_PM_RUNTIME_UART
> + if (pdev->id != 0) {
> + pm_runtime_disable(&pdev->dev);
> + pm_runtime_set_suspended(&pdev->dev);
> + }
> +#endif
> + uart_remove_one_port(&sunplus_uart_driver,
> + &sunplus_uart_ports[pdev->id].uport);
> +
> + if (pdev->id < UART_NR) {
> + clk_disable_unprepare(sunplus_uart_ports[pdev->id].clk);
> + reset_control_assert(sunplus_uart_ports[pdev->id].rstc);
> + }
What about the PERI clocks? This seems to leave them enabled.
regards
Philipp
^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH v2 0/2] Add UART driver for Suplus SP7021 SoC
2021-11-10 7:51 ` [PATCH v2 0/2] Add UART driver for Suplus SP7021 SoC Hammer Hsieh
2021-11-10 7:51 ` [PATCH v2 1/2] dt-bindings:serial:Add bindings doc for Sunplus SoC UART Driver Hammer Hsieh
2021-11-10 7:51 ` [PATCH v2 2/2] serial:sunplus-uart:Add " Hammer Hsieh
@ 2021-11-10 16:41 ` Andy Shevchenko
2 siblings, 0 replies; 19+ messages in thread
From: Andy Shevchenko @ 2021-11-10 16:41 UTC (permalink / raw)
To: Hammer Hsieh
Cc: Greg Kroah-Hartman, Rob Herring, open list:SERIAL DRIVERS,
devicetree, Linux Kernel Mailing List, Jiri Slaby, Philipp Zabel,
tony.huang, wells.lu, Hammer Hsieh
On Wed, Nov 10, 2021 at 9:51 AM Hammer Hsieh <hammerh0314@gmail.com> wrote:
>
> This is a patch series for UART driver for Suplus SP7021 SoC.
>
> Sunplus SP7021 is an ARM Cortex A7 (4 cores) based SoC. It integrates
> many peripherals (ex: UART. I2C, SPI, SDIO, eMMC, USB, SD card and
> etc.) into a single chip. It is designed for industrial control.
>
> Refer to:
> https://sunplus-tibbo.atlassian.net/wiki/spaces/doc/overview
> https://tibbo.com/store/plus1.html
...
> drivers/tty/serial/sunplus-uart.c | 1591 ++++++++++++++++++++
> include/soc/sunplus/sp_uart.h | 147 ++
Sorry, but I do not believe this driver requires so many LOCs. Please,
try to get it under 1000, I am pretty sure it's possible and
achievable.
--
With Best Regards,
Andy Shevchenko
^ permalink raw reply [flat|nested] 19+ messages in thread
* RE: [PATCH v2 2/2] serial:sunplus-uart:Add Sunplus SoC UART Driver
2021-11-10 9:50 ` Philipp Zabel
@ 2021-11-11 9:45 ` Hammer Hsieh 謝宏孟
0 siblings, 0 replies; 19+ messages in thread
From: Hammer Hsieh 謝宏孟 @ 2021-11-11 9:45 UTC (permalink / raw)
To: Philipp Zabel, Hammer Hsieh, gregkh, robh+dt, linux-serial,
devicetree, linux-kernel, jirislaby
Cc: Tony Huang 黃懷厚, Wells Lu 呂芳騰
> -----Original Message-----
> From: Philipp Zabel <p.zabel@pengutronix.de>
> Sent: Wednesday, November 10, 2021 5:50 PM
> To: Hammer Hsieh <hammerh0314@gmail.com>; gregkh@linuxfoundation.org;
> robh+dt@kernel.org; linux-serial@vger.kernel.org; devicetree@vger.kernel.org;
> linux-kernel@vger.kernel.org; jirislaby@kernel.org
> Cc: Tony Huang 黃懷厚 <tony.huang@sunplus.com>; Wells Lu 呂芳騰
> <wells.lu@sunplus.com>; Hammer Hsieh 謝宏孟
> <hammer.hsieh@sunplus.com>
> Subject: Re: [PATCH v2 2/2] serial:sunplus-uart:Add Sunplus SoC UART Driver
>
> Hi,
>
> On Wed, 2021-11-10 at 15:51 +0800, Hammer Hsieh wrote:
> [...]
> > +struct sunplus_uart_port {
> > + char name[16];
> > + struct uart_port uport;
> > + struct sunplus_dma_info *uartdma_rx;
> > + struct sunplus_dma_info *uartdma_tx;
> > + struct clk *clk;
> > + struct reset_control *rstc;
> > + unsigned int pllsys_rate;
> > + struct gpio_desc *rts_gpio;
> > + struct hrtimer rts_check_tx_empty;
> > + struct hrtimer rts_delay_before_send;
> > + struct hrtimer rts_delay_after_send; }; struct sunplus_uart_port
> > +sunplus_uart_ports[UART_NR];
>
> Does this have to be a global array? I would expect these to be allocated in the
> probe function, one at a time.
>
With console, it uses global array.
Such as:
/drivers/tty/serial/ar933x_uart.c
#ifdef CONFIG_SERIAL_AR933X_CONSOLE
ar933x_uart_port * ar933x_console_port[ ];
With normal use, it should probe once at a time.
I will think about how to modify it.
> [...]
> > +static int sunplus_uart_probe(struct platform_device *pdev) {
> > + struct resource *res_mem;
> > + struct uart_port *port;
> > + struct clk *clk, *pllsys;
> > + unsigned int pllsys_rate;
> > + int ret, irq;
> > + int idx_offset, idx;
> > + int idx_which_uart;
> > + char peri_name[16];
> > +
> > + if (pdev->dev.of_node) {
> > + pdev->id = of_alias_get_id(pdev->dev.of_node, "serial");
> > + if (pdev->id < 0)
> > + pdev->id = of_alias_get_id(pdev->dev.of_node, "uart");
> > + }
> > +
> > + idx_offset = -1;
> > +
> > + if (IS_UARTDMARX_ID(pdev->id))
> > + idx_offset = 0;
> > + else if (IS_UARTDMATX_ID(pdev->id))
> > + idx_offset = UART_DMARX_NR;
> > +
> > + /* init txdma or rxdma */
> > + if (idx_offset >= 0) {
> > + clk = devm_clk_get(&pdev->dev, NULL);
>
> Should this be requested by name? Looking at the binding, this could be
> UADMA or HWUA?
>
Yes, it is better requested by name.
But , if request by name , I can't probe both dma_tx and dma_rx with one line.
I will think about how to modify it.
> > + if (IS_ERR(clk))
> > + return PTR_ERR(clk);
> > +
> > + ret = clk_prepare_enable(clk);
> > + if (ret)
> > + return ret;
>
> I suggest to move this down after all required resources are available.
> Otherwise you'll have to either disable the clock in the error paths, or you are
> left with a running clock if anything below fails.
>
OK, I will modify it.
> > + if (idx_offset == 0)
> > + idx = idx_offset + pdev->id - ID_BASE_DMARX;
> > + else
> > + idx = idx_offset + pdev->id - ID_BASE_DMATX;
> > +
> > + res_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> > + if (!res_mem)
> > + return -ENODEV;
> > +
> > + sprintf(peri_name, "PERI%d", (idx & 0x01));
> > +
> > + clk = devm_clk_get(&pdev->dev, peri_name);
> > + if (IS_ERR(clk))
> > + return PTR_ERR(clk);
> > +
> > + ret = clk_prepare_enable(clk);
>
> Same as above.
OK, I will modify it.
>
> > + if (ret)
> > + return ret;
> > +
> > + sunplus_uartdma[idx].addr_phy =
> > + (unsigned long)(res_mem->start);
> > + sunplus_uartdma[idx].membase =
> > + devm_ioremap_resource(&pdev->dev, res_mem);
> > +
> > + if (IS_ERR(sunplus_uartdma[idx].membase))
> > + return PTR_ERR(sunplus_uartdma[idx].membase);
> > +
> > + if (IS_UARTDMARX_ID(pdev->id)) {
> > + irq = platform_get_irq(pdev, 0);
> > + if (irq < 0)
> > + return -ENODEV;
> > +
> > + sunplus_uartdma[idx].irq = irq;
> > + } else {
> > + res_mem = platform_get_resource(pdev, IORESOURCE_MEM,
> 1);
> > + if (!res_mem)
> > + return -ENODEV;
> > +
> > + sunplus_uartdma[idx].gdma_membase =
> > + devm_ioremap_resource(&pdev->dev, res_mem);
> > +
> > + if (IS_ERR(sunplus_uartdma[idx].gdma_membase))
> > + return -EINVAL;
> > + }
> > +
> > + if (of_property_read_u32(pdev->dev.of_node, "which-uart",
> &idx_which_uart) != 0) {
> > + dev_err(&pdev->dev, "\"which-uart\" is not assigned.");
> > + return -EINVAL;
> > + }
> > +
> > + if (idx_which_uart >= UART_NR) {
> > + dev_err(&pdev->dev, "\"which-uart\" is not valid.");
> > + return -EINVAL;
> > + }
> > +
> > + sunplus_uartdma[idx].which_uart = idx_which_uart;
> > +
> > + return 0;
> > + } else if (pdev->id < 0 || pdev->id >= UART_NR)
> > + return -EINVAL;
> > +
> > + /* init uart */
> > + port = &sunplus_uart_ports[pdev->id].uport;
> > + if (port->membase)
> > + return -EBUSY;
> > +
> > + memset(port, 0, sizeof(*port));
> > +
> > + res_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> > + if (!res_mem)
> > + return -ENODEV;
> > +
> > + port->dev = &pdev->dev;
> > + port->mapbase = res_mem->start;
> > +
> > + port->membase = devm_ioremap_resource(&pdev->dev, res_mem);
> > + if (IS_ERR(port->membase))
> > + return PTR_ERR(port->membase);
> > +
> > + irq = platform_get_irq(pdev, 0);
> > + if (irq < 0)
> > + return -ENODEV;
> > +
> > + uart_get_rs485_mode(port);
> > + sunplus_uart_ports[pdev->id].rts_gpio =
> > + devm_gpiod_get(&pdev->dev, "rts", GPIOD_OUT_LOW);
> > + port->rs485_config = sunplus_uart_config_rs485;
> > + sunplus_uart_ports[pdev->id].rts_check_tx_empty.function = NULL;
> > + sunplus_uart_ports[pdev->id].rts_delay_before_send.function = NULL;
> > + sunplus_uart_ports[pdev->id].rts_delay_after_send.function = NULL;
> > + if (port->rs485.flags & SER_RS485_ENABLED)
> > + sunplus_uart_rs485_on(port);
> > +
> > + sunplus_uart_ports[pdev->id].clk = devm_clk_get(&pdev->dev, NULL);
>
> Here the same nameless clock as in the loop above is requested again.
> Should this be UADMA or HWUA?
>
No, here should be UART clk, each uart didn't use "clock-names" , that's why we use NULL.
In dts UART only use clocks=<&clkc UA0> or <&clkc UA1> or <&clkc UA2>.
We did not use "clock-names".
uart_probe( ) , first init dma , then init uart.
> > + if (IS_ERR(sunplus_uart_ports[pdev->id].clk))
> > + return PTR_ERR(sunplus_uart_ports[pdev->id].clk);
> > +
> > + ret = clk_prepare_enable(sunplus_uart_ports[pdev->id].clk);
> > + if (ret)
> > + return ret;
>
> Same comment as above. Better to request the reset control before enabling
> the clock, for example.
>
OK, I will modify it.
> > +
> > + sunplus_uart_ports[pdev->id].rstc =
> > + devm_reset_control_get(&pdev->dev, NULL);
>
> Please use devm_reset_control_get_exclusive() instead.
>
OK, I will modify it.
> > +
> > + if (IS_ERR(sunplus_uart_ports[pdev->id].rstc))
> > + return PTR_ERR(sunplus_uart_ports[pdev->id].rstc);
> > +
> > + ret = reset_control_deassert(sunplus_uart_ports[pdev->id].rstc);
> > + if (ret)
> > + return ret;
> > +
> > + clk = sunplus_uart_ports[pdev->id].clk;
> > + if (IS_ERR(clk))
>
> This can't ever be true, the code above already returned in this case.
>
Indeed, I will modify it.
> [...]
> > +static int sunplus_uart_remove(struct platform_device *pdev) { #ifdef
> > +CONFIG_PM_RUNTIME_UART
> > + if (pdev->id != 0) {
> > + pm_runtime_disable(&pdev->dev);
> > + pm_runtime_set_suspended(&pdev->dev);
> > + }
> > +#endif
> > + uart_remove_one_port(&sunplus_uart_driver,
> > + &sunplus_uart_ports[pdev->id].uport);
> > +
> > + if (pdev->id < UART_NR) {
> > + clk_disable_unprepare(sunplus_uart_ports[pdev->id].clk);
> > + reset_control_assert(sunplus_uart_ports[pdev->id].rstc);
> > + }
>
> What about the PERI clocks? This seems to leave them enabled.
>
In case of dma enable, we should consider it.
I will modify it.
> regards
> Philipp
^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH v2 2/2] serial:sunplus-uart:Add Sunplus SoC UART Driver
2021-11-10 7:51 ` [PATCH v2 2/2] serial:sunplus-uart:Add " Hammer Hsieh
2021-11-10 9:50 ` Philipp Zabel
@ 2021-11-12 8:31 ` kernel test robot
1 sibling, 0 replies; 19+ messages in thread
From: kernel test robot @ 2021-11-12 8:31 UTC (permalink / raw)
To: Hammer Hsieh, gregkh, robh+dt, linux-serial, devicetree,
linux-kernel, jirislaby, p.zabel
Cc: kbuild-all, tony.huang, wells.lu, Hammer Hsieh
[-- Attachment #1: Type: text/plain, Size: 1826 bytes --]
Hi Hammer,
I love your patch! Yet something to improve:
[auto build test ERROR on tty/tty-testing]
[also build test ERROR on robh/for-next linux/master linus/master v5.15 next-20211112]
[If your patch is applied to the wrong git tree, kindly drop us a note.
And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch]
url: https://github.com/0day-ci/linux/commits/Hammer-Hsieh/dt-bindings-serial-Add-bindings-doc-for-Sunplus-SoC-UART-Driver/20211110-165153
base: https://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty.git tty-testing
config: x86_64-allyesconfig (attached as .config)
compiler: gcc-9 (Debian 9.3.0-22) 9.3.0
reproduce (this is a W=1 build):
# https://github.com/0day-ci/linux/commit/bf691d823221e8ab7a6710bcf06c227fcb00ac6d
git remote add linux-review https://github.com/0day-ci/linux
git fetch --no-tags linux-review Hammer-Hsieh/dt-bindings-serial-Add-bindings-doc-for-Sunplus-SoC-UART-Driver/20211110-165153
git checkout bf691d823221e8ab7a6710bcf06c227fcb00ac6d
# save the attached .config to linux build tree
mkdir build_dir
make W=1 O=build_dir ARCH=x86_64 SHELL=/bin/bash
If you fix the issue, kindly add following tag as appropriate
Reported-by: kernel test robot <lkp@intel.com>
All errors (new ones prefixed by >>):
>> drivers/tty/serial/sunplus-uart.c:32:10: fatal error: dt-bindings/clock/sp-sp7021.h: No such file or directory
32 | #include <dt-bindings/clock/sp-sp7021.h>
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
compilation terminated.
vim +32 drivers/tty/serial/sunplus-uart.c
> 32 #include <dt-bindings/clock/sp-sp7021.h>
33
---
0-DAY CI Kernel Test Service, Intel Corporation
https://lists.01.org/hyperkitty/list/kbuild-all@lists.01.org
[-- Attachment #2: .config.gz --]
[-- Type: application/gzip, Size: 66523 bytes --]
^ permalink raw reply [flat|nested] 19+ messages in thread
* [PATCH v3 0/2] Add UART driver for Suplus SP7021 SoC
2021-11-01 7:48 [PATCH 0/2] Add UART driver for Suplus SP7021 SoC hammer.hsieh
` (2 preceding siblings ...)
2021-11-10 7:51 ` [PATCH v2 0/2] Add UART driver for Suplus SP7021 SoC Hammer Hsieh
@ 2021-11-19 5:19 ` Hammer Hsieh
2021-11-19 5:19 ` [PATCH v3 1/2] dt-bindings:serial:Add bindings doc for Sunplus SoC UART Driver Hammer Hsieh
2021-11-19 5:19 ` [PATCH v3 2/2] serial:sunplus-uart:Add " Hammer Hsieh
3 siblings, 2 replies; 19+ messages in thread
From: Hammer Hsieh @ 2021-11-19 5:19 UTC (permalink / raw)
To: gregkh, robh+dt, linux-serial, devicetree, linux-kernel,
jirislaby, p.zabel
Cc: tony.huang, wells.lu, Hammer Hsieh
This is a patch series for UART driver for Suplus SP7021 SoC.
Sunplus SP7021 is an ARM Cortex A7 (4 cores) based SoC. It integrates
many peripherals (ex: UART. I2C, SPI, SDIO, eMMC, USB, SD card and
etc.) into a single chip. It is designed for industrial control.
Refer to:
https://sunplus-tibbo.atlassian.net/wiki/spaces/doc/overview
https://tibbo.com/store/plus1.html
Hammer Hsieh (2):
dt-bindings:serial:Add bindings doc for Sunplus SoC UART Driver
serial:sunplus-uart:Add Sunplus SoC UART Driver
.../bindings/serial/sunplus,sp7021-uart.yaml | 58 ++
MAINTAINERS | 7 +
drivers/tty/serial/Kconfig | 23 +
drivers/tty/serial/Makefile | 1 +
drivers/tty/serial/sunplus-uart.c | 903 +++++++++++++++++++++
include/soc/sunplus/sp_uart.h | 93 +++
6 files changed, 1085 insertions(+)
create mode 100644 Documentation/devicetree/bindings/serial/sunplus,sp7021-uart.yaml
create mode 100644 drivers/tty/serial/sunplus-uart.c
create mode 100644 include/soc/sunplus/sp_uart.h
--
2.7.4
^ permalink raw reply [flat|nested] 19+ messages in thread
* [PATCH v3 1/2] dt-bindings:serial:Add bindings doc for Sunplus SoC UART Driver
2021-11-19 5:19 ` [PATCH v3 " Hammer Hsieh
@ 2021-11-19 5:19 ` Hammer Hsieh
2021-11-29 0:22 ` Rob Herring
2021-11-19 5:19 ` [PATCH v3 2/2] serial:sunplus-uart:Add " Hammer Hsieh
1 sibling, 1 reply; 19+ messages in thread
From: Hammer Hsieh @ 2021-11-19 5:19 UTC (permalink / raw)
To: gregkh, robh+dt, linux-serial, devicetree, linux-kernel,
jirislaby, p.zabel
Cc: tony.huang, wells.lu, Hammer Hsieh
Add bindings doc for Sunplus SoC UART Driver
Signed-off-by: Hammer Hsieh <hammer.hsieh@sunplus.com>
---
Changes in v3:
- Modify yaml file based on uart driver (remove dma function).
.../bindings/serial/sunplus,sp7021-uart.yaml | 58 ++++++++++++++++++++++
MAINTAINERS | 5 ++
2 files changed, 63 insertions(+)
create mode 100644 Documentation/devicetree/bindings/serial/sunplus,sp7021-uart.yaml
diff --git a/Documentation/devicetree/bindings/serial/sunplus,sp7021-uart.yaml b/Documentation/devicetree/bindings/serial/sunplus,sp7021-uart.yaml
new file mode 100644
index 0000000..df11074
--- /dev/null
+++ b/Documentation/devicetree/bindings/serial/sunplus,sp7021-uart.yaml
@@ -0,0 +1,58 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+# Copyright (C) Sunplus Co., Ltd. 2021
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/serial/sunplus,sp7021-uart.yaml#"
+$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+
+title: Sunplus SoC SP7021 UART Controller Device Tree Bindings
+
+maintainers:
+ - Tony Huang <tony.huang@sunplus.com>
+ - Hammer Hsieh <hammer.hsieh@sunplus.com>
+ - Wells Lu <wells.lu@sunplus.com>
+
+allOf:
+ - $ref: serial.yaml#
+
+properties:
+ compatible:
+ const: sunplus,sp7021-uart
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ clocks:
+ maxItems: 1
+
+ resets:
+ maxItems: 1
+
+required:
+ - compatible
+ - reg
+ - interrupts
+ - clocks
+ - resets
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/irq.h>
+ aliases {
+ serial0 = &uart0;
+ };
+
+ uart0: serial@9c000900 {
+ compatible = "sunplus,sp7021-uart";
+ reg = <0x9c000900 0x80>;
+ interrupt-parent = <&intc>;
+ interrupts = <53 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clkc 0x28>;
+ resets = <&rstc 0x18>;
+ };
+...
diff --git a/MAINTAINERS b/MAINTAINERS
index 3b79fd4..f2ee40c 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -17945,6 +17945,11 @@ L: netdev@vger.kernel.org
S: Maintained
F: drivers/net/ethernet/dlink/sundance.c
+SUNPLUS UART DRIVER
+M: Hammer Hsieh <hammer.hsieh@sunplus.com>
+S: Maintained
+F: Documentation/devicetree/bindings/serial/sunplus,sp7021-uart.yaml
+
SUPERH
M: Yoshinori Sato <ysato@users.sourceforge.jp>
M: Rich Felker <dalias@libc.org>
--
2.7.4
^ permalink raw reply related [flat|nested] 19+ messages in thread
* [PATCH v3 2/2] serial:sunplus-uart:Add Sunplus SoC UART Driver
2021-11-19 5:19 ` [PATCH v3 " Hammer Hsieh
2021-11-19 5:19 ` [PATCH v3 1/2] dt-bindings:serial:Add bindings doc for Sunplus SoC UART Driver Hammer Hsieh
@ 2021-11-19 5:19 ` Hammer Hsieh
2021-11-19 9:35 ` Andy Shevchenko
1 sibling, 1 reply; 19+ messages in thread
From: Hammer Hsieh @ 2021-11-19 5:19 UTC (permalink / raw)
To: gregkh, robh+dt, linux-serial, devicetree, linux-kernel,
jirislaby, p.zabel
Cc: tony.huang, wells.lu, Hammer Hsieh
Add Sunplus SoC UART Driver
Signed-off-by: Hammer Hsieh <hammer.hsieh@sunplus.com>
---
Changes in v3:
- Addressed all comments from Andy Shevchenko and Philipp Zabel.
MAINTAINERS | 2 +
drivers/tty/serial/Kconfig | 23 +
drivers/tty/serial/Makefile | 1 +
drivers/tty/serial/sunplus-uart.c | 903 ++++++++++++++++++++++++++++++++++++++
include/soc/sunplus/sp_uart.h | 93 ++++
5 files changed, 1022 insertions(+)
create mode 100644 drivers/tty/serial/sunplus-uart.c
create mode 100644 include/soc/sunplus/sp_uart.h
diff --git a/MAINTAINERS b/MAINTAINERS
index f2ee40c..14790a4 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -17949,6 +17949,8 @@ SUNPLUS UART DRIVER
M: Hammer Hsieh <hammer.hsieh@sunplus.com>
S: Maintained
F: Documentation/devicetree/bindings/serial/sunplus,sp7021-uart.yaml
+F: drivers/tty/serial/sunplus-uart.c
+F: include/soc/sunplus/sp-uart.h
SUPERH
M: Yoshinori Sato <ysato@users.sourceforge.jp>
diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig
index 131a6a5..319f5db 100644
--- a/drivers/tty/serial/Kconfig
+++ b/drivers/tty/serial/Kconfig
@@ -1561,6 +1561,29 @@ config SERIAL_LITEUART_CONSOLE
and warnings and which allows logins in single user mode).
Otherwise, say 'N'.
+config SERIAL_SUNPLUS
+ bool "Sunplus UART support"
+ depends on OF
+ select SERIAL_CORE
+ help
+ Select this option if you would like to use Sunplus serial port on
+ Sunplus SoC SP7021.
+ If you enable this option, Sunplus serial ports in the system will
+ be registered as ttySx.
+
+config SERIAL_SUNPLUS_CONSOLE
+ bool "Console on Sunplus UART"
+ depends on SERIAL_SUNPLUS
+ select SERIAL_CORE_CONSOLE
+ select SERIAL_EARLYCON
+ help
+ Select this option if you would like to use a Sunplus UART as the
+ system console.
+ Even if you say Y here, the currently visible virtual console
+ (/dev/tty0) will still be used as the system console by default, but
+ you can alter that using a kernel command line option such as
+ "console=ttySx".
+
endmenu
config SERIAL_MCTRL_GPIO
diff --git a/drivers/tty/serial/Makefile b/drivers/tty/serial/Makefile
index 7da0856..61cc8de 100644
--- a/drivers/tty/serial/Makefile
+++ b/drivers/tty/serial/Makefile
@@ -87,6 +87,7 @@ obj-$(CONFIG_SERIAL_RDA) += rda-uart.o
obj-$(CONFIG_SERIAL_MILBEAUT_USIO) += milbeaut_usio.o
obj-$(CONFIG_SERIAL_SIFIVE) += sifive.o
obj-$(CONFIG_SERIAL_LITEUART) += liteuart.o
+obj-$(CONFIG_SERIAL_SUNPLUS) += sunplus-uart.o
# GPIOLIB helpers for modem control lines
obj-$(CONFIG_SERIAL_MCTRL_GPIO) += serial_mctrl_gpio.o
diff --git a/drivers/tty/serial/sunplus-uart.c b/drivers/tty/serial/sunplus-uart.c
new file mode 100644
index 0000000..b339772
--- /dev/null
+++ b/drivers/tty/serial/sunplus-uart.c
@@ -0,0 +1,903 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Sunplus SoC UART driver
+ *
+ * Author: Hammer Hsieh <hammer.hsieh@sunplus.com>
+ * Tony Huang <tony.huang@sunplus.com>
+ * Wells Lu <wells.lu@sunplus.com>
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/console.h>
+#include <linux/interrupt.h>
+#include <linux/platform_device.h>
+#include <linux/tty.h>
+#include <linux/tty_flip.h>
+#include <linux/of_platform.h>
+#include <asm/irq.h>
+#include <linux/sysrq.h>
+#include <linux/serial_core.h>
+#include <linux/clk.h>
+#include <linux/reset.h>
+#include <linux/io.h>
+#include <linux/pm_runtime.h>
+#include <linux/of.h>
+#include <linux/delay.h>
+#include <soc/sunplus/sp_uart.h>
+
+#define UART_NR 5
+
+static struct uart_driver sunplus_uart_driver;
+
+struct sunplus_uart_port {
+ char name[16];
+ struct uart_port port;
+ struct clk *clk;
+ struct reset_control *rstc;
+};
+
+static inline struct sunplus_uart_port *to_sunplus_uart(struct uart_port *port)
+{
+ return container_of(port, struct sunplus_uart_port, port);
+}
+
+static inline void sp_uart_put_char(struct uart_port *port, unsigned int ch)
+{
+ writel(ch, port->membase + SP_UART_DATA);
+}
+
+static inline u32 sp_uart_line_status_tx_buf_not_full(struct uart_port *port)
+{
+ return ((readl(port->membase + SP_UART_LSR) & SP_UART_LSR_TX)
+ ? SP_UART_LSR_TX_NOT_FULL : 0);
+}
+
+static unsigned int sunplus_tx_empty(struct uart_port *port)
+{
+ return ((readl(port->membase + SP_UART_LSR) & SP_UART_LSR_TXE)
+ ? TIOCSER_TEMT : 0);
+}
+
+static void sunplus_set_mctrl(struct uart_port *port, unsigned int mctrl)
+{
+ unsigned int mcr = readl(port->membase + SP_UART_MCR);
+
+ if (mctrl & TIOCM_DTR)
+ mcr |= SP_UART_MCR_DTS;
+ else
+ mcr &= ~SP_UART_MCR_DTS;
+
+ if (mctrl & TIOCM_RTS)
+ mcr |= SP_UART_MCR_RTS;
+ else
+ mcr &= ~SP_UART_MCR_RTS;
+
+ if (mctrl & TIOCM_CAR)
+ mcr |= SP_UART_MCR_DCD;
+ else
+ mcr &= ~SP_UART_MCR_DCD;
+
+ if (mctrl & TIOCM_RI)
+ mcr |= SP_UART_MCR_RI;
+ else
+ mcr &= ~SP_UART_MCR_RI;
+
+ if (mctrl & TIOCM_LOOP)
+ mcr |= SP_UART_MCR_LB;
+ else
+ mcr &= ~SP_UART_MCR_LB;
+
+ writel(mcr, port->membase + SP_UART_MCR);
+
+}
+
+static unsigned int sunplus_get_mctrl(struct uart_port *port)
+{
+ unsigned int ret, mcr;
+
+ mcr = readl(port->membase + SP_UART_MCR);
+
+ if (mcr & SP_UART_MCR_DTS)
+ ret |= TIOCM_DTR;
+
+ if (mcr & SP_UART_MCR_RTS)
+ ret |= TIOCM_RTS;
+
+ if (mcr & SP_UART_MCR_DCD)
+ ret |= TIOCM_CAR;
+
+ if (mcr & SP_UART_MCR_RI)
+ ret |= TIOCM_RI;
+
+ if (mcr & SP_UART_MCR_LB)
+ ret |= TIOCM_LOOP;
+
+ if (mcr & SP_UART_MCR_AC)
+ ret |= TIOCM_CTS;
+
+ return ret;
+}
+
+static void sunplus_stop_tx(struct uart_port *port)
+{
+ unsigned int isc;
+
+ isc = readl(port->membase + SP_UART_ISC);
+ isc &= ~SP_UART_ISC_TXM;
+ writel(isc, port->membase + SP_UART_ISC);
+}
+
+static void sunplus_start_tx(struct uart_port *port)
+{
+ unsigned int isc;
+
+ isc = readl(port->membase + SP_UART_ISC);
+ isc |= SP_UART_ISC_TXM;
+ writel(isc, port->membase + SP_UART_ISC);
+}
+
+static void sunplus_stop_rx(struct uart_port *port)
+{
+ unsigned int isc;
+
+ isc = readl(port->membase + SP_UART_ISC);
+ isc &= ~SP_UART_ISC_RXM;
+ writel(isc, port->membase + SP_UART_ISC);
+}
+
+static void sunplus_enable_ms(struct uart_port *port)
+{
+ /* Do nothing */
+}
+
+static void sunplus_break_ctl(struct uart_port *port, int ctl)
+{
+ unsigned long flags;
+ unsigned int lcr;
+
+ spin_lock_irqsave(&port->lock, flags);
+
+ lcr = readl(port->membase + SP_UART_LCR);
+
+ if (ctl != 0)
+ lcr |= SP_UART_LCR_BC; /* start break */
+ else
+ lcr &= ~SP_UART_LCR_BC; /* stop break */
+
+ writel(lcr, port->membase + SP_UART_LCR);
+
+ spin_unlock_irqrestore(&port->lock, flags);
+}
+
+static void transmit_chars(struct uart_port *port)
+{
+ struct circ_buf *xmit = &port->state->xmit;
+
+ if (port->x_char) {
+ sp_uart_put_char(port, port->x_char);
+ port->icount.tx++;
+ port->x_char = 0;
+ return;
+ }
+
+ if (uart_circ_empty(xmit) || uart_tx_stopped(port)) {
+ sunplus_stop_tx(port);
+ return;
+ }
+
+ do {
+ sp_uart_put_char(port, xmit->buf[xmit->tail]);
+ xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
+ port->icount.tx++;
+
+ if (uart_circ_empty(xmit))
+ break;
+ } while (sp_uart_line_status_tx_buf_not_full(port));
+
+
+ if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
+ uart_write_wakeup(port);
+
+ if (uart_circ_empty(xmit))
+ sunplus_stop_tx(port);
+}
+
+/* called by ISR */
+static void receive_chars(struct uart_port *port)
+{
+ struct tty_struct *tty = port->state->port.tty;
+ unsigned int lsr = readl(port->membase + SP_UART_LSR);
+ unsigned int ch, flag;
+
+ do {
+ ch = readl(port->membase + SP_UART_DATA);
+
+ flag = TTY_NORMAL;
+ port->icount.rx++;
+
+ if (unlikely(lsr & SP_UART_LSR_BRK_ERROR_BITS)) {
+ if (port->cons == NULL)
+ dev_err(port->dev, "UART%d, SP_UART_LSR_BRK_ERROR_BITS, lsr = 0x%08X\n",
+ port->line, lsr);
+
+ if (lsr & SP_UART_LSR_BC) {
+ lsr &= ~(SP_UART_LSR_FE | SP_UART_LSR_PE);
+ port->icount.brk++;
+ if (uart_handle_break(port))
+ goto ignore_char;
+ } else if (lsr & SP_UART_LSR_PE) {
+ if (port->cons == NULL)
+ dev_err(port->dev, "UART%d, SP_UART_LSR_PE\n", port->line);
+ port->icount.parity++;
+ } else if (lsr & SP_UART_LSR_FE) {
+ if (port->cons == NULL)
+ dev_err(port->dev, "UART%d, SP_UART_LSR_FE\n", port->line);
+ port->icount.frame++;
+ }
+ if (lsr & SP_UART_LSR_OE) {
+ if (port->cons == NULL)
+ dev_err(port->dev, "UART%d, SP_UART_LSR_OE\n", port->line);
+ port->icount.overrun++;
+ }
+
+ /*
+ * Mask off conditions which should be ignored.
+ */
+
+ /* lsr &= port->read_status_mask; */
+
+ if (lsr & SP_UART_LSR_BC)
+ flag = TTY_BREAK;
+ else if (lsr & SP_UART_LSR_PE)
+ flag = TTY_PARITY;
+ else if (lsr & SP_UART_LSR_FE)
+ flag = TTY_FRAME;
+ }
+
+ if (port->ignore_status_mask & SP_UART_CREAD_DISABLED)
+ goto ignore_char;
+
+ if (uart_handle_sysrq_char(port, ch))
+ goto ignore_char;
+
+ uart_insert_char(port, lsr, SP_UART_LSR_OE, ch, flag);
+
+ignore_char:
+ lsr = readl(port->membase + SP_UART_LSR);
+ } while (lsr & SP_UART_LSR_RX);
+
+ if (tty) {
+ spin_unlock(&port->lock);
+ tty_flip_buffer_push(tty->port);
+ spin_lock(&port->lock);
+ }
+}
+
+static irqreturn_t sunplus_uart_irq(int irq, void *args)
+{
+ struct uart_port *port = (struct uart_port *)args;
+ unsigned long flags;
+
+ spin_lock_irqsave(&port->lock, flags);
+
+ if (readl(port->membase + SP_UART_ISC) & SP_UART_ISC_RX)
+ receive_chars(port);
+
+ if (readl(port->membase + SP_UART_ISC) & SP_UART_ISC_TX)
+ transmit_chars(port);
+
+ spin_unlock_irqrestore(&port->lock, flags);
+
+ return IRQ_HANDLED;
+}
+
+static int sunplus_startup(struct uart_port *port)
+{
+ struct sunplus_uart_port *sup = to_sunplus_uart(port);
+ u32 interrupt_en;
+ int ret;
+
+#ifdef CONFIG_PM_RUNTIME_UART
+ if (port->line > 0) {
+ ret = pm_runtime_get_sync(port->dev);
+ if (ret < 0)
+ goto out;
+ }
+#endif
+
+ ret = request_irq(port->irq, sunplus_uart_irq, 0, sup->name, port);
+ if (ret)
+ return ret;
+
+ /*
+ * don't need to use spin_lock_irqsave() because interrupts
+ * are globally disabled
+ */
+ spin_lock_irq(&port->lock);
+
+ /* SP_UART_ISC_TXM is enabled in .start_tx() */
+ interrupt_en |= SP_UART_ISC_RXM;
+
+ writel(interrupt_en, port->membase + SP_UART_ISC);
+
+ spin_unlock_irq(&port->lock);
+
+#ifdef CONFIG_PM_RUNTIME_UART
+ if (port->line > 0)
+ pm_runtime_put(port->dev);
+
+ return 0;
+
+out:
+ if (port->line > 0) {
+ pm_runtime_mark_last_busy(port->dev);
+ pm_runtime_put_autosuspend(port->dev);
+ }
+#endif
+ return 0;
+
+}
+
+static void sunplus_shutdown(struct uart_port *port)
+{
+ unsigned int mcr;
+ unsigned long flags;
+
+ spin_lock_irqsave(&port->lock, flags);
+ writel(0, port->membase + SP_UART_ISC);
+ spin_unlock_irqrestore(&port->lock, flags);
+
+ free_irq(port->irq, port);
+
+ /* Disable flow control of Tx, so that queued data can be sent out
+ * There is no way for s/w to let h/w abort in the middle of
+ * transaction.
+ * Don't reset module except it's in idle state. Otherwise, it might
+ * cause bus to hang.
+ */
+ mcr = readl(port->membase + SP_UART_MCR);
+ mcr &= ~SP_UART_MCR_AC;
+ writel(mcr, port->membase + SP_UART_MCR);
+
+}
+
+static void sunplus_set_termios(struct uart_port *port,
+ struct ktermios *termios, struct ktermios *oldtermios)
+{
+ u32 clk, ext, div, div_l, div_h, baud;
+ u32 lcr, mcr;
+ unsigned long flags;
+
+ clk = port->uartclk;
+
+ baud = uart_get_baud_rate(port, termios, oldtermios, 0, port->uartclk / 16);
+
+ /*
+ * Send all data in Tx FIFO before changing clock source,
+ * it should be UART0 only
+ */
+ while (!(readl(port->membase + SP_UART_LSR) & SP_UART_LSR_TXE))
+ ;
+
+ clk += baud >> 1;
+ div = clk / baud;
+ ext = div & 0x0F;
+ div = (div >> 4) - 1;
+ div_l = (div & 0xFF) | (ext << 12);
+ div_h = div >> 8;
+
+ switch (termios->c_cflag & CSIZE) {
+ case CS5:
+ lcr = SP_UART_LCR_WL5;
+ break;
+ case CS6:
+ lcr = SP_UART_LCR_WL6;
+ break;
+ case CS7:
+ lcr = SP_UART_LCR_WL7;
+ break;
+ default: /* CS8 */
+ lcr = SP_UART_LCR_WL8;
+ break;
+ }
+
+ if (termios->c_cflag & CSTOPB)
+ lcr |= SP_UART_LCR_ST;
+
+ if (termios->c_cflag & PARENB) {
+ lcr |= SP_UART_LCR_PE;
+
+ if (!(termios->c_cflag & PARODD))
+ lcr |= SP_UART_LCR_PR;
+ }
+
+ spin_lock_irqsave(&port->lock, flags);
+
+ uart_update_timeout(port, termios->c_cflag, baud);
+
+ port->read_status_mask = 0;
+ if (termios->c_iflag & INPCK)
+ port->read_status_mask |= SP_UART_LSR_PE | SP_UART_LSR_FE;
+
+ if (termios->c_iflag & (BRKINT | PARMRK))
+ port->read_status_mask |= SP_UART_LSR_BC;
+
+ /*
+ * Characters to ignore
+ */
+ port->ignore_status_mask = 0;
+ if (termios->c_iflag & IGNPAR)
+ port->ignore_status_mask |= SP_UART_LSR_FE | SP_UART_LSR_PE;
+
+ if (termios->c_iflag & IGNBRK) {
+ port->ignore_status_mask |= SP_UART_LSR_BC;
+
+ if (termios->c_iflag & IGNPAR)
+ port->ignore_status_mask |= SP_UART_LSR_OE;
+ }
+
+ /*
+ * Ignore all characters if CREAD is not set.
+ */
+ if ((termios->c_cflag & CREAD) == 0) {
+ port->ignore_status_mask |= SP_UART_CREAD_DISABLED;
+ /* flush rx data FIFO */
+ writel(0, port->membase + SP_UART_RX_RESIDUE);
+ }
+
+ mcr = readl(port->membase + SP_UART_MCR);
+
+ if (termios->c_cflag & CRTSCTS)
+ mcr |= (SP_UART_MCR_AC | SP_UART_MCR_AR);
+ else
+ mcr &= ~(SP_UART_MCR_AC | SP_UART_MCR_AR);
+
+ writel(mcr, port->membase + SP_UART_MCR);
+
+ /* do not set these in emulation */
+ writel(div_h, port->membase + SP_UART_DIV_H);
+ writel(div_l, port->membase + SP_UART_DIV_L);
+ writel(lcr, port->membase + SP_UART_LCR);
+
+ spin_unlock_irqrestore(&port->lock, flags);
+}
+
+static void sunplus_set_ldisc(struct uart_port *port,
+ struct ktermios *termios)
+{
+ int new = termios->c_line;
+
+ if (new == N_PPS) {
+ port->flags |= UPF_HARDPPS_CD;
+ sunplus_enable_ms(port);
+ } else {
+ port->flags &= ~UPF_HARDPPS_CD;
+ }
+}
+
+static const char *sunplus_type(struct uart_port *port)
+{
+ struct sunplus_uart_port *sup = to_sunplus_uart(port);
+
+ return sup->name;
+}
+
+static void sunplus_release_port(struct uart_port *port)
+{
+}
+
+static int sunplus_request_port(struct uart_port *port)
+{
+ return 0;
+}
+
+static void sunplus_config_port(struct uart_port *port, int type)
+{
+ if (type & UART_CONFIG_TYPE) {
+ port->type = PORT_SUNPLUS;
+ sunplus_request_port(port);
+ }
+}
+
+static int sunplus_verify_port(struct uart_port *port, struct serial_struct *serial)
+{
+ return -EINVAL;
+}
+
+#ifdef CONFIG_CONSOLE_POLL
+static int sunplus_poll_init(struct uart_port *port)
+{
+ return 0;
+}
+
+static void sunplus_poll_put_char(struct uart_port *port, unsigned char data)
+{
+ wait_for_xmitr(port);
+ sp_uart_put_char(port, data);
+}
+
+static int sunplus_poll_get_char(struct uart_port *port)
+{
+ unsigned int lsr;
+
+ do {
+ lsr = readl(port->membase + SP_UART_LSR);
+ } while (!(lsr & SP_UART_LSR_RX));
+
+ return readl(port->membase + SP_UART_DATA);
+}
+#endif /* CONFIG_CONSOLE_POLL */
+
+static const struct uart_ops sunplus_uart_ops = {
+ .tx_empty = sunplus_tx_empty,
+ .set_mctrl = sunplus_set_mctrl,
+ .get_mctrl = sunplus_get_mctrl,
+ .stop_tx = sunplus_stop_tx,
+ .start_tx = sunplus_start_tx,
+ .stop_rx = sunplus_stop_rx,
+ .enable_ms = sunplus_enable_ms,
+ .break_ctl = sunplus_break_ctl,
+ .startup = sunplus_startup,
+ .shutdown = sunplus_shutdown,
+ .set_termios = sunplus_set_termios,
+ .set_ldisc = sunplus_set_ldisc,
+ .type = sunplus_type,
+ .release_port = sunplus_release_port,
+ .request_port = sunplus_request_port,
+ .config_port = sunplus_config_port,
+ .verify_port = sunplus_verify_port,
+#ifdef CONFIG_CONSOLE_POLL
+ .poll_init = sunplus_poll_init,
+ .poll_put_char = sunplus_poll_put_char,
+ .poll_get_char = sunplus_poll_get_char,
+#endif /* CONFIG_CONSOLE_POLL */
+};
+
+#ifdef CONFIG_SERIAL_SUNPLUS_CONSOLE
+struct sunplus_uart_port *sunplus_console_ports[UART_NR];
+
+static inline void wait_for_xmitr(struct uart_port *port)
+{
+ while (1) {
+ if (sp_uart_line_status_tx_buf_not_full(port))
+ break;
+ }
+}
+
+static void sunplus_uart_console_putchar(struct uart_port *port, int ch)
+{
+ wait_for_xmitr(port);
+ sp_uart_put_char(port, ch);
+}
+
+static void sunplus_uart_console_write(struct console *co,
+ const char *s, unsigned int count)
+{
+ unsigned long flags;
+ int locked = 1;
+
+ local_irq_save(flags);
+
+ if (sunplus_console_ports[co->index]->port.sysrq)
+ locked = 0;
+ else if (oops_in_progress)
+ locked = spin_trylock(&sunplus_console_ports[co->index]->port.lock);
+ else
+ spin_lock(&sunplus_console_ports[co->index]->port.lock);
+
+ uart_console_write(&sunplus_console_ports[co->index]->port,
+ s, count, sunplus_uart_console_putchar);
+
+ if (locked)
+ spin_unlock(&sunplus_console_ports[co->index]->port.lock);
+
+ local_irq_restore(flags);
+}
+
+static int __init sunplus_uart_console_setup(struct console *co, char *options)
+{
+ struct sunplus_uart_port *sup;
+ int baud = 115200;
+ int bits = 8;
+ int parity = 'n';
+ int flow = 'n';
+
+ if ((co->index >= UART_NR) || (co->index < 0))
+ return -EINVAL;
+
+ sup = sunplus_console_ports[co->index];
+
+ if (options)
+ uart_parse_options(options, &baud, &parity, &bits, &flow);
+
+ return uart_set_options(&sup->port, co, baud, parity, bits, flow);
+}
+
+static struct console sunplus_uart_console = {
+ .name = "ttyS",
+ .write = sunplus_uart_console_write,
+ .device = uart_console_device,
+ .setup = sunplus_uart_console_setup,
+ .flags = CON_PRINTBUFFER,
+ .index = -1,
+ .data = &sunplus_uart_driver
+};
+#endif
+
+static struct uart_driver sunplus_uart_driver = {
+ .owner = THIS_MODULE,
+ .driver_name = "Sunplus_UART",
+ .dev_name = "ttyS",
+ .major = TTY_MAJOR,
+ .minor = 64,
+ .nr = UART_NR,
+ .cons = NULL,
+};
+
+static int sunplus_uart_probe(struct platform_device *pdev)
+{
+ struct sunplus_uart_port *sup;
+ struct resource *res_mem;
+ struct uart_port *port;
+ int ret, irq;
+
+ if (pdev->dev.of_node) {
+ pdev->id = of_alias_get_id(pdev->dev.of_node, "serial");
+ if (pdev->id < 0)
+ pdev->id = of_alias_get_id(pdev->dev.of_node, "uart");
+ }
+
+ if (pdev->id < 0 || pdev->id >= UART_NR)
+ return -EINVAL;
+
+ sup = devm_kzalloc(&pdev->dev, sizeof(struct sunplus_uart_port),
+ GFP_KERNEL);
+ if (!sup)
+ return -ENOMEM;
+
+ sup->clk = devm_clk_get(&pdev->dev, NULL);
+ if (IS_ERR(sup->clk)) {
+ dev_err(&pdev->dev, "unable to get UART clock\n");
+ return PTR_ERR(sup->clk);
+ }
+
+ sup->rstc = devm_reset_control_get_exclusive(&pdev->dev, NULL);
+ if (IS_ERR(sup->rstc))
+ return PTR_ERR(sup->rstc);
+
+ port = &sup->port;
+
+ res_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!res_mem)
+ return -ENODEV;
+
+ port->membase = devm_ioremap_resource(&pdev->dev, res_mem);
+ if (IS_ERR(port->membase))
+ return PTR_ERR(port->membase);
+
+ ret = clk_prepare_enable(sup->clk);
+ if (ret)
+ return ret;
+
+ port->uartclk = clk_get_rate(sup->clk);
+ if (!port->uartclk) {
+ ret = -EINVAL;
+ goto err_disable_clk;
+ }
+
+ irq = platform_get_irq(pdev, 0);
+ if (irq < 0)
+ return -ENODEV;
+
+ port->mapbase = res_mem->start;
+ port->line = pdev->id;
+ port->irq = irq;
+ port->dev = &pdev->dev;
+ port->iotype = UPIO_MEM;
+ port->ops = &sunplus_uart_ops;
+ port->flags = UPF_BOOT_AUTOCONF;
+ port->fifosize = 128;
+
+ ret = reset_control_deassert(sup->rstc);
+ if (ret)
+ return ret;
+
+#ifdef CONFIG_SERIAL_SUNPLUS_CONSOLE
+ if (pdev->id == 0)
+ port->cons = &sunplus_uart_console;
+ sunplus_console_ports[sup->port.line] = sup;
+#endif
+
+ port->private_data = container_of(&sup->port,
+ struct sunplus_uart_port, port);
+
+ sprintf(sup->name, "sp_uart%d", pdev->id);
+
+ ret = uart_add_one_port(&sunplus_uart_driver, &sup->port);
+ if (ret)
+ goto err_disable_clk;
+
+ platform_set_drvdata(pdev, sup);
+
+#ifdef CONFIG_PM_RUNTIME_UART
+ if (pdev->id != 0) {
+ pm_runtime_set_autosuspend_delay(&pdev->dev, 5000);
+ pm_runtime_use_autosuspend(&pdev->dev);
+ pm_runtime_set_active(&pdev->dev);
+ pm_runtime_enable(&pdev->dev);
+ }
+#endif
+ return 0;
+
+err_disable_clk:
+ clk_disable_unprepare(sup->clk);
+ return ret;
+
+}
+
+static int sunplus_uart_remove(struct platform_device *pdev)
+{
+ struct sunplus_uart_port *sup;
+
+ sup = platform_get_drvdata(pdev);
+#ifdef CONFIG_PM_RUNTIME_UART
+ if (pdev->id != 0) {
+ pm_runtime_disable(&pdev->dev);
+ pm_runtime_set_suspended(&pdev->dev);
+ }
+#endif
+ uart_remove_one_port(&sunplus_uart_driver, &sup->port);
+
+ if (pdev->id < UART_NR) {
+ clk_disable_unprepare(sup->clk);
+ reset_control_assert(sup->rstc);
+ }
+
+ return 0;
+}
+
+static int sunplus_uart_suspend(struct platform_device *pdev,
+ pm_message_t state)
+{
+ struct sunplus_uart_port *sup;
+
+ sup = platform_get_drvdata(pdev);
+
+ /* Don't suspend uart0 for cmd line usage */
+ if ((pdev->id < UART_NR) && (pdev->id > 0))
+ reset_control_assert(sup->rstc);
+
+ return 0;
+}
+
+static int sunplus_uart_resume(struct platform_device *pdev)
+{
+ struct sunplus_uart_port *sup;
+
+ sup = platform_get_drvdata(pdev);
+
+ if (pdev->id < UART_NR) {
+ clk_prepare_enable(sup->clk);
+ reset_control_deassert(sup->rstc);
+ }
+ return 0;
+}
+
+#ifdef CONFIG_PM_RUNTIME_UART
+static int sunplus_uart_runtime_suspend(struct device *dev)
+{
+ struct platform_device *pdev = to_platform_device(dev);
+ struct sunplus_uart_port *sup;
+
+ sup = platform_get_drvdata(pdev);
+
+ /* Don't suspend uart0 for cmd line usage */
+ if ((pdev->id < UART_NR) && (pdev->id > 0))
+ reset_control_assert(sup->rstc);
+
+ return 0;
+}
+
+static int sunplus_uart_runtime_resume(struct device *dev)
+{
+ struct platform_device *pdev = to_platform_device(dev);
+ struct sunplus_uart_port *sup;
+
+ sup = platform_get_drvdata(pdev);
+
+ if (pdev->id < UART_NR) {
+ clk_prepare_enable(sup->clk);
+ reset_control_deassert(sup->rstc);
+ }
+
+ return 0;
+}
+static const struct dev_pm_ops sp7021_uart_pm_ops = {
+ .runtime_suspend = sunplus_uart_runtime_suspend,
+ .runtime_resume = sunplus_uart_runtime_resume,
+};
+#define sunplus_uart_pm_ops (&sp7021_uart_pm_ops)
+#endif
+
+static const struct of_device_id sp_uart_of_match[] = {
+ { .compatible = "sunplus,sp7021-uart" },
+ {},
+};
+MODULE_DEVICE_TABLE(of, sp_uart_of_match);
+
+static struct platform_driver sunplus_uart_platform_driver = {
+ .probe = sunplus_uart_probe,
+ .remove = sunplus_uart_remove,
+ .suspend = sunplus_uart_suspend,
+ .resume = sunplus_uart_resume,
+ .driver = {
+ .name = "sunplus-uart",
+ .owner = THIS_MODULE,
+ .of_match_table = of_match_ptr(sp_uart_of_match),
+#ifdef CONFIG_PM_RUNTIME_UART
+ .pm = sunplus_uart_pm_ops,
+#endif
+ }
+};
+
+static int __init sunplus_uart_init(void)
+{
+ int ret;
+
+#ifdef CONFIG_SERIAL_SUNPLUS_CONSOLE
+ sunplus_uart_driver.cons = &sunplus_uart_console;
+#endif
+
+ ret = uart_register_driver(&sunplus_uart_driver);
+ if (ret < 0)
+ return ret;
+
+ ret = platform_driver_register(&sunplus_uart_platform_driver);
+ if (ret != 0) {
+ uart_unregister_driver(&sunplus_uart_driver);
+ return ret;
+ }
+
+ return 0;
+}
+module_init(sunplus_uart_init);
+
+#ifdef CONFIG_SERIAL_EARLYCON
+static void sunplus_uart_putc(struct uart_port *port, int c)
+{
+ unsigned int status;
+
+ for (;;) {
+ status = readl(port->membase + SP_UART_LSR);
+ if ((status & SP_UART_LSR_TXE) == SP_UART_LSR_TXE)
+ break;
+ cpu_relax();
+ }
+ writel(c, port->membase + SP_UART_DATA);
+}
+
+static void sunplus_uart_early_write(struct console *con,
+ const char *s, unsigned int n)
+{
+ struct earlycon_device *dev = con->data;
+
+ uart_console_write(&dev->port, s, n, sunplus_uart_putc);
+}
+
+int __init sunplus_uart_early_setup(struct earlycon_device *device,
+ const char *opt)
+{
+ if (!(device->port.membase || device->port.iobase))
+ return -ENODEV;
+
+ device->con->write = sunplus_uart_early_write;
+ return 0;
+}
+OF_EARLYCON_DECLARE(sunplus_uart, "sunplus,sp7021-uart", sunplus_uart_early_setup);
+#endif
+
+MODULE_DESCRIPTION("Sunplus UART driver");
+MODULE_AUTHOR("Hammer Hsieh <hammer.hsieh@sunplus.com>");
+MODULE_LICENSE("GPL v2");
diff --git a/include/soc/sunplus/sp_uart.h b/include/soc/sunplus/sp_uart.h
new file mode 100644
index 0000000..c34c8d0
--- /dev/null
+++ b/include/soc/sunplus/sp_uart.h
@@ -0,0 +1,93 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Sunplus SoC UART driver header file
+ */
+
+#ifndef __SP_UART_H__
+#define __SP_UART_H__
+
+#ifdef CONFIG_DEBUG_SP_UART
+#include <mach/io_map.h>
+
+#define LL_UART_PADDR PA_IOB_ADDR(18 * 32 * 4)
+#define LL_UART_VADDR VA_IOB_ADDR(18 * 32 * 4)
+#define LOGI_ADDR_UART0_REG VA_IOB_ADDR(18 * 32 * 4)
+#endif
+
+/*
+ * UART REG
+ *
+ */
+#define SP_UART_DATA 0x00
+#define SP_UART_LSR 0x04
+#define SP_UART_MSR 0x08
+#define SP_UART_LCR 0x0C
+#define SP_UART_MCR 0x10
+#define SP_UART_DIV_L 0x14
+#define SP_UART_DIV_H 0x18
+#define SP_UART_ISC 0x1C
+#define SP_UART_TX_RESIDUE 0x20
+#define SP_UART_RX_RESIDUE 0x24
+
+/* lsr
+ * 1: trasmit fifo is empty
+ */
+#define SP_UART_LSR_TXE (1 << 6)
+
+/* interrupt
+ * SP_UART_LSR_BC : break condition
+ * SP_UART_LSR_FE : frame error
+ * SP_UART_LSR_OE : overrun error
+ * SP_UART_LSR_PE : parity error
+ * SP_UART_LSR_RX : 1: receive fifo not empty
+ * SP_UART_LSR_TX : 1: transmit fifo is not full
+ */
+#define SP_UART_CREAD_DISABLED (1 << 16)
+#define SP_UART_LSR_BC (1 << 5)
+#define SP_UART_LSR_FE (1 << 4)
+#define SP_UART_LSR_OE (1 << 3)
+#define SP_UART_LSR_PE (1 << 2)
+#define SP_UART_LSR_RX (1 << 1)
+#define SP_UART_LSR_TX (1 << 0)
+#define SP_UART_LSR_TX_NOT_FULL 1
+
+#define SP_UART_LSR_BRK_ERROR_BITS \
+ (SP_UART_LSR_PE | SP_UART_LSR_OE | SP_UART_LSR_FE | SP_UART_LSR_BC)
+
+/* lcr */
+#define SP_UART_LCR_WL5 (0 << 0)
+#define SP_UART_LCR_WL6 (1 << 0)
+#define SP_UART_LCR_WL7 (2 << 0)
+#define SP_UART_LCR_WL8 (3 << 0)
+#define SP_UART_LCR_ST (1 << 2)
+#define SP_UART_LCR_PE (1 << 3)
+#define SP_UART_LCR_PR (1 << 4)
+#define SP_UART_LCR_BC (1 << 5)
+
+/* isc
+ * SP_UART_ISC_MSM : Modem status ctrl
+ * SP_UART_ISC_LSM : Line status interrupt
+ * SP_UART_ISC_RXM : RX interrupt, when got some input data
+ * SP_UART_ISC_TXM : TX interrupt, when trans start
+ */
+#define SP_UART_ISC_MSM (1 << 7)
+#define SP_UART_ISC_LSM (1 << 6)
+#define SP_UART_ISC_RXM (1 << 5)
+#define SP_UART_ISC_TXM (1 << 4)
+#define HAS_UART_ISC_FLAGMASK 0x0F
+#define SP_UART_ISC_MS (1 << 3)
+#define SP_UART_ISC_LS (1 << 2)
+#define SP_UART_ISC_RX (1 << 1)
+#define SP_UART_ISC_TX (1 << 0)
+
+/* modem control register */
+#define SP_UART_MCR_AT (1 << 7)
+#define SP_UART_MCR_AC (1 << 6)
+#define SP_UART_MCR_AR (1 << 5)
+#define SP_UART_MCR_LB (1 << 4)
+#define SP_UART_MCR_RI (1 << 3)
+#define SP_UART_MCR_DCD (1 << 2)
+#define SP_UART_MCR_RTS (1 << 1)
+#define SP_UART_MCR_DTS (1 << 0)
+
+#endif /* __SP_UART_H__ */
--
2.7.4
^ permalink raw reply related [flat|nested] 19+ messages in thread
* Re: [PATCH v3 2/2] serial:sunplus-uart:Add Sunplus SoC UART Driver
2021-11-19 5:19 ` [PATCH v3 2/2] serial:sunplus-uart:Add " Hammer Hsieh
@ 2021-11-19 9:35 ` Andy Shevchenko
2021-11-23 3:43 ` Hammer Hsieh 謝宏孟
0 siblings, 1 reply; 19+ messages in thread
From: Andy Shevchenko @ 2021-11-19 9:35 UTC (permalink / raw)
To: Hammer Hsieh
Cc: Greg Kroah-Hartman, Rob Herring, open list:SERIAL DRIVERS,
devicetree, Linux Kernel Mailing List, Jiri Slaby, Philipp Zabel,
tony.huang, wells.lu, Hammer Hsieh
On Fri, Nov 19, 2021 at 8:14 AM Hammer Hsieh <hammerh0314@gmail.com> wrote:
>
> Add Sunplus SoC UART Driver
Thanks for update, my comments below.
...
> drivers/tty/serial/sunplus-uart.c | 903 ++++++++++++++++++++++++++++++++++++++
I believe 50 LOCs easily can be removed (see below for a few examples
I caught just by looking into this for less than 1 minute).
...
> include/soc/sunplus/sp_uart.h | 93 ++++
Why do you need this header?
...
> +config SERIAL_SUNPLUS
> + bool "Sunplus UART support"
No module? Why?
> + depends on OF
No COMPILE_TEST, why?
> + select SERIAL_CORE
> + help
> + Select this option if you would like to use Sunplus serial port on
> + Sunplus SoC SP7021.
> + If you enable this option, Sunplus serial ports in the system will
> + be registered as ttySx.
If it's ttySx, it most probably 8250 compatible, no?
...
> +/*
> + * Sunplus SoC UART driver
> + *
> + * Author: Hammer Hsieh <hammer.hsieh@sunplus.com>
> + * Tony Huang <tony.huang@sunplus.com>
> + * Wells Lu <wells.lu@sunplus.com>
> + *
Redundant.
> + */
...
> +#include <linux/module.h>
> +#include <linux/init.h>
> +#include <linux/console.h>
> +#include <linux/interrupt.h>
> +#include <linux/platform_device.h>
> +#include <linux/tty.h>
> +#include <linux/tty_flip.h>
> +#include <linux/of_platform.h>
> +#include <asm/irq.h>
> +#include <linux/sysrq.h>
> +#include <linux/serial_core.h>
> +#include <linux/clk.h>
> +#include <linux/reset.h>
> +#include <linux/io.h>
> +#include <linux/pm_runtime.h>
> +#include <linux/of.h>
> +#include <linux/delay.h>
Sort above alphabetically and get rid of unneeded headers.
> +#include <soc/sunplus/sp_uart.h>
...
> +#define UART_NR 5
We have this as a config option, why do you need a separate one?
...
> +static struct uart_driver sunplus_uart_driver;
Why global variables?
...
> +struct sunplus_uart_port {
> + char name[16];
uart_port has a name, what is this one for?
> + struct uart_port port;
It's better to make it first in the structure to optimize container_of() away.
> + struct clk *clk;
> + struct reset_control *rstc;
> +};
...
> +static inline u32 sp_uart_line_status_tx_buf_not_full(struct uart_port *port)
> +{
> + return ((readl(port->membase + SP_UART_LSR) & SP_UART_LSR_TX)
> + ? SP_UART_LSR_TX_NOT_FULL : 0);
Use temporary variables for better reading. Here and everywhere else
where it's applicable.
> +}
...
> + writel(mcr, port->membase + SP_UART_MCR);
> +
Redundant blank line. Check everywhere you have no such waste space.
...
> +static void sunplus_enable_ms(struct uart_port *port)
> +{
> + /* Do nothing */
> +}
Is this stub needed at all?
...
> +
> +
One blank line is enough.
...
> + if (port->cons == NULL)
Don't we have a special API to check if the port is a console or not?
> + dev_err(port->dev, "UART%d, SP_UART_LSR_FE\n", port->line);
...
> +#ifdef CONFIG_PM_RUNTIME_UART
> + if (port->line > 0) {
> + ret = pm_runtime_get_sync(port->dev);
> + if (ret < 0)
> + goto out;
> + }
> +#endif
Can we postpone implementation of it right now, please?
Can you test this [1] series instead?
[1]: https://lore.kernel.org/linux-serial/20211115084203.56478-1-tony@atomide.com/T/#u
...
> + /* Disable flow control of Tx, so that queued data can be sent out
> + * There is no way for s/w to let h/w abort in the middle of
> + * transaction.
> + * Don't reset module except it's in idle state. Otherwise, it might
the module unless
in an idle
> + * cause bus to hang.
> + */
...
> + /*
> + * Send all data in Tx FIFO before changing clock source,
> + * it should be UART0 only
> + */
> + while (!(readl(port->membase + SP_UART_LSR) & SP_UART_LSR_TXE))
> + ;
We do not allow busyloops in the kernel. Consider readl_poll_timeout()
or its atomic variant.
...
> + clk += baud >> 1;
> + div = clk / baud;
> + ext = div & 0x0F;
> + div = (div >> 4) - 1;
> + div_l = (div & 0xFF) | (ext << 12);
> + div_h = div >> 8;
Divisor voodoo should be explained in the comment.
...
> +static void sunplus_release_port(struct uart_port *port)
> +{
> +}
> +
> +static int sunplus_request_port(struct uart_port *port)
> +{
> + return 0;
> +}
> +static int sunplus_verify_port(struct uart_port *port, struct serial_struct *serial)
> +{
> + return -EINVAL;
> +}
Why the stubs?
...
> +static inline void wait_for_xmitr(struct uart_port *port)
> +{
> + while (1) {
> + if (sp_uart_line_status_tx_buf_not_full(port))
> + break;
> + }
read_poll_timeout() or its atomic variant.
> +}
...
> + if (pdev->dev.of_node) {
Redundant check
> + pdev->id = of_alias_get_id(pdev->dev.of_node, "serial");
> + if (pdev->id < 0)
> + pdev->id = of_alias_get_id(pdev->dev.of_node, "uart");
> + }
> +
Redundant blank line.
> + if (pdev->id < 0 || pdev->id >= UART_NR)
> + return -EINVAL;
...
> + sup = devm_kzalloc(&pdev->dev, sizeof(struct sunplus_uart_port),
> + GFP_KERNEL);
sizeof(*sup) and make it one line.
> + if (!sup)
> + return -ENOMEM;
...
> + sup->clk = devm_clk_get(&pdev->dev, NULL);
> + if (IS_ERR(sup->clk)) {
> + dev_err(&pdev->dev, "unable to get UART clock\n");
> + return PTR_ERR(sup->clk);
Respect deferred probe by
return dev_err_probe(...);
> + }
...
> + res_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + if (!res_mem)
> + return -ENODEV;
> +
Redundant check, besides that...
> + port->membase = devm_ioremap_resource(&pdev->dev, res_mem);
> + if (IS_ERR(port->membase))
> + return PTR_ERR(port->membase);
...there is an API that does these two in one.
...
> + port->uartclk = clk_get_rate(sup->clk);
> + if (!port->uartclk) {
> + ret = -EINVAL;
> + goto err_disable_clk;
Instead use devm_add_action_or_reset() as many other drivers do in the kernel.
> + }
...
> + irq = platform_get_irq(pdev, 0);
> + if (irq < 0)
> + return -ENODEV;
What's wrong with the error code in the irq variable?
...
> + port->private_data = container_of(&sup->port,
> + struct sunplus_uart_port, port);
What does this mean?
...
> +static const struct of_device_id sp_uart_of_match[] = {
> + { .compatible = "sunplus,sp7021-uart" },
> + {},
No comma for terminator entries.
> +};
...
> +static struct platform_driver sunplus_uart_platform_driver = {
> + .probe = sunplus_uart_probe,
> + .remove = sunplus_uart_remove,
> + .suspend = sunplus_uart_suspend,
> + .resume = sunplus_uart_resume,
> + .driver = {
> + .name = "sunplus-uart",
> + .owner = THIS_MODULE,
This is done by registration call, no?
> + .of_match_table = of_match_ptr(sp_uart_of_match),
Effectively a warning (but you don't see it since COMPILE_TEST is missed).
Hint: drop of_match_ptr() completely.
> +#ifdef CONFIG_PM_RUNTIME_UART
> + .pm = sunplus_uart_pm_ops,
> +#endif
> + }
> +};
...
> + ret = platform_driver_register(&sunplus_uart_platform_driver);
> + if (ret != 0) {
Keep the same style over the driver.
> + uart_unregister_driver(&sunplus_uart_driver);
> + return ret;
> + }
...
> + for (;;) {
> + status = readl(port->membase + SP_UART_LSR);
> + if ((status & SP_UART_LSR_TXE) == SP_UART_LSR_TXE)
> + break;
> + cpu_relax();
> + }
real_poll_timeout*()
--
With Best Regards,
Andy Shevchenko
^ permalink raw reply [flat|nested] 19+ messages in thread
* RE: [PATCH v3 2/2] serial:sunplus-uart:Add Sunplus SoC UART Driver
2021-11-19 9:35 ` Andy Shevchenko
@ 2021-11-23 3:43 ` Hammer Hsieh 謝宏孟
0 siblings, 0 replies; 19+ messages in thread
From: Hammer Hsieh 謝宏孟 @ 2021-11-23 3:43 UTC (permalink / raw)
To: Andy Shevchenko, Hammer Hsieh
Cc: Greg Kroah-Hartman, Rob Herring, open list:SERIAL DRIVERS,
devicetree, Linux Kernel Mailing List, Jiri Slaby, Philipp Zabel,
Tony Huang 黃懷厚,
Wells Lu 呂芳騰
Hi, Andy Shevchenko :
I may not fully understand all your comments.
But most of them I will modify when next submit.
I try to answer all your comments below.
And also have some question about some of your comments.
Thanks
Regards,
Hammer
> -----Original Message-----
> From: Andy Shevchenko <andy.shevchenko@gmail.com>
> Sent: Friday, November 19, 2021 5:35 PM
> To: Hammer Hsieh <hammerh0314@gmail.com>
> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>; Rob Herring
> <robh+dt@kernel.org>; open list:SERIAL DRIVERS
> <linux-serial@vger.kernel.org>; devicetree <devicetree@vger.kernel.org>;
> Linux Kernel Mailing List <linux-kernel@vger.kernel.org>; Jiri Slaby
> <jirislaby@kernel.org>; Philipp Zabel <p.zabel@pengutronix.de>; Tony Huang
> 黃懷厚 <tony.huang@sunplus.com>; Wells Lu 呂芳騰
> <wells.lu@sunplus.com>; Hammer Hsieh 謝宏孟
> <hammer.hsieh@sunplus.com>
> Subject: Re: [PATCH v3 2/2] serial:sunplus-uart:Add Sunplus SoC UART Driver
>
> On Fri, Nov 19, 2021 at 8:14 AM Hammer Hsieh <hammerh0314@gmail.com>
> wrote:
> >
> > Add Sunplus SoC UART Driver
>
> Thanks for update, my comments below.
>
> ...
>
> > drivers/tty/serial/sunplus-uart.c | 903
> > ++++++++++++++++++++++++++++++++++++++
>
> I believe 50 LOCs easily can be removed (see below for a few examples I caught
> just by looking into this for less than 1 minute).
>
> ...
>
> > include/soc/sunplus/sp_uart.h | 93 ++++
>
> Why do you need this header?
>
Ok, will remove header file, reg define will move to sunplus-uart.c
> ...
>
> > +config SERIAL_SUNPLUS
> > + bool "Sunplus UART support"
>
> No module? Why?
Will add tristate for it. I will confirm load/unload *.ko for it.
>
> > + depends on OF
>
> No COMPILE_TEST, why?
Will add COMPILE_TEST for it.
>
> > + select SERIAL_CORE
> > + help
> > + Select this option if you would like to use Sunplus serial port on
> > + Sunplus SoC SP7021.
> > + If you enable this option, Sunplus serial ports in the system will
> > + be registered as ttySx.
>
> If it's ttySx, it most probably 8250 compatible, no?
>
No , it is a single chip, not 8250 compatible.
I plan to use 'ttySUP' for Sunplus SoC UART.
We define PORT_SUNPLUS 123 at /include/uapi/linux/serial_core.h
Is that ok?
> ...
>
> > +/*
> > + * Sunplus SoC UART driver
> > + *
> > + * Author: Hammer Hsieh <hammer.hsieh@sunplus.com>
> > + * Tony Huang <tony.huang@sunplus.com>
> > + * Wells Lu <wells.lu@sunplus.com>
>
> > + *
>
> Redundant.
>
Ok , will remove it.
> > + */
>
> ...
>
> > +#include <linux/module.h>
> > +#include <linux/init.h>
> > +#include <linux/console.h>
> > +#include <linux/interrupt.h>
> > +#include <linux/platform_device.h>
> > +#include <linux/tty.h>
> > +#include <linux/tty_flip.h>
> > +#include <linux/of_platform.h>
> > +#include <asm/irq.h>
> > +#include <linux/sysrq.h>
> > +#include <linux/serial_core.h>
> > +#include <linux/clk.h>
> > +#include <linux/reset.h>
> > +#include <linux/io.h>
> > +#include <linux/pm_runtime.h>
> > +#include <linux/of.h>
> > +#include <linux/delay.h>
>
> Sort above alphabetically and get rid of unneeded headers.
>
> > +#include <soc/sunplus/sp_uart.h>
>
Ok , will do it.
> ...
>
> > +#define UART_NR 5
>
> We have this as a config option, why do you need a separate one?
>
Can I keep UART_NR in sunplus-uart.c ?
If all uart driver define CONFIG_xxx_UART_NR in Kconfig.
Kconfig will get big very fast.
In sunplus-uart.c just only one line code.
In Kconfig takes 8 ~ 10 line code.
> ...
>
> > +static struct uart_driver sunplus_uart_driver;
>
> Why global variables?
>
It is define for struct console { }
I will move it to close to struct console { }
> ...
> > +struct sunplus_uart_port {
> > + char name[16];
>
> uart_port has a name, what is this one for?
>
Ok , will remove it.
> > + struct uart_port port;
>
> It's better to make it first in the structure to optimize container_of() away.
>
> > + struct clk *clk;
> > + struct reset_control *rstc;
> > +};
>
Ok, thanks for the information.
> ...
>
> > +static inline u32 sp_uart_line_status_tx_buf_not_full(struct
> > +uart_port *port) {
> > + return ((readl(port->membase + SP_UART_LSR) &
> SP_UART_LSR_TX)
> > + ? SP_UART_LSR_TX_NOT_FULL : 0);
>
> Use temporary variables for better reading. Here and everywhere else where
> it's applicable.
>
> > +}
>
Ok, will modify it.
> ...
>
> > + writel(mcr, port->membase + SP_UART_MCR);
> > +
>
> Redundant blank line. Check everywhere you have no such waste space.
>
Ok, will remove it.
> ...
>
> > +static void sunplus_enable_ms(struct uart_port *port) {
> > + /* Do nothing */
> > +}
>
> Is this stub needed at all?
>
No, will remove it.
> ...
>
> > +
> > +
>
> One blank line is enough.
>
Ok, will remove it.
> ...
>
> > + if (port->cons == NULL)
>
> Don't we have a special API to check if the port is a console or not?
>
Can you show me the API ?
> > + dev_err(port->dev,
> "UART%d,
> > + SP_UART_LSR_FE\n", port->line);
>
> ...
>
> > +#ifdef CONFIG_PM_RUNTIME_UART
> > + if (port->line > 0) {
> > + ret = pm_runtime_get_sync(port->dev);
> > + if (ret < 0)
> > + goto out;
> > + }
> > +#endif
>
> Can we postpone implementation of it right now, please?
> Can you test this [1] series instead?
>
> [1]:
> https://lore.kernel.org/linux-serial/20211115084203.56478-1-tony@atomide.c
> om/T/#u
>
I don't understand what's going on this issue?
> ...
>
> > + /* Disable flow control of Tx, so that queued data can be sent out
> > + * There is no way for s/w to let h/w abort in the middle of
> > + * transaction.
> > + * Don't reset module except it's in idle state. Otherwise, it
> > + might
>
> the module unless
> in an idle
>
> > + * cause bus to hang.
> > + */
>
> ...
>
> > + /*
> > + * Send all data in Tx FIFO before changing clock source,
> > + * it should be UART0 only
> > + */
> > + while (!(readl(port->membase + SP_UART_LSR) &
> SP_UART_LSR_TXE))
> > + ;
>
> We do not allow busyloops in the kernel. Consider readl_poll_timeout() or its
> atomic variant.
>
Ok, will modify for it.
> ...
>
> > + clk += baud >> 1;
> > + div = clk / baud;
> > + ext = div & 0x0F;
> > + div = (div >> 4) - 1;
> > + div_l = (div & 0xFF) | (ext << 12);
> > + div_h = div >> 8;
>
> Divisor voodoo should be explained in the comment.
>
Ok, will add explanation for it.
> ...
>
> > +static void sunplus_release_port(struct uart_port *port) { }
> > +
> > +static int sunplus_request_port(struct uart_port *port) {
> > + return 0;
> > +}
>
> > +static int sunplus_verify_port(struct uart_port *port, struct
> > +serial_struct *serial) {
> > + return -EINVAL;
> > +}
>
> Why the stubs?
>
Will modify it.
Like below:
if((type!= PORT_UNKNOWN) && (type != PORT_SUNPLUS))
return -EINVAL;
return 0;
> ...
>
> > +static inline void wait_for_xmitr(struct uart_port *port) {
> > + while (1) {
> > + if (sp_uart_line_status_tx_buf_not_full(port))
> > + break;
> > + }
>
> read_poll_timeout() or its atomic variant.
>
Ok, will modify it.
> > +}
>
> ...
>
> > + if (pdev->dev.of_node) {
>
> Redundant check
Sure, will remove it.
>
> > + pdev->id = of_alias_get_id(pdev->dev.of_node, "serial");
> > + if (pdev->id < 0)
> > + pdev->id = of_alias_get_id(pdev->dev.of_node,
> "uart");
> > + }
>
> > +
>
> Redundant blank line.
Ok, will remove it.
>
> > + if (pdev->id < 0 || pdev->id >= UART_NR)
> > + return -EINVAL;
>
> ...
>
> > + sup = devm_kzalloc(&pdev->dev, sizeof(struct sunplus_uart_port),
> > + GFP_KERNEL);
>
> sizeof(*sup) and make it one line.
>
Ok, will modify it.
> > + if (!sup)
> > + return -ENOMEM;
>
> ...
>
> > + sup->clk = devm_clk_get(&pdev->dev, NULL);
> > + if (IS_ERR(sup->clk)) {
> > + dev_err(&pdev->dev, "unable to get UART clock\n");
> > + return PTR_ERR(sup->clk);
>
> Respect deferred probe by
>
> return dev_err_probe(...);
>
Ok, will modify it.
> > + }
>
> ...
>
> > + res_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
>
> > + if (!res_mem)
> > + return -ENODEV;
> > +
>
> Redundant check, besides that...
Ok, will remove it.
>
> > + port->membase = devm_ioremap_resource(&pdev->dev,
> res_mem);
> > + if (IS_ERR(port->membase))
> > + return PTR_ERR(port->membase);
>
> ...there is an API that does these two in one.
>
API of_ioremap(res, offset, sizeof(xx), "xxx") can do it.
But we didn't use reg-names for it in dts.
I think it is better keep orginal platform_get_resource() + devm_ioremap_resource().
> ...
>
> > + port->uartclk = clk_get_rate(sup->clk);
> > + if (!port->uartclk) {
> > + ret = -EINVAL;
>
> > + goto err_disable_clk;
>
> Instead use devm_add_action_or_reset() as many other drivers do in the
> kernel.
>
> > + }
>
Ok, will modify it.
> ...
>
> > + irq = platform_get_irq(pdev, 0);
> > + if (irq < 0)
> > + return -ENODEV;
>
> What's wrong with the error code in the irq variable?
>
Will change 'return -ENODEV' to 'return irq'.
> ...
>
> > + port->private_data = container_of(&sup->port,
> > + struct sunplus_uart_port, port);
>
> What does this mean?
>
Previous code use it to store 'struct sunplus_uart_port' pointer, will remove it.
> ...
>
> > +static const struct of_device_id sp_uart_of_match[] = {
> > + { .compatible = "sunplus,sp7021-uart" },
>
> > + {},
>
> No comma for terminator entries.
>
Ok, will remove it.
> > +};
>
> ...
>
> > +static struct platform_driver sunplus_uart_platform_driver = {
> > + .probe = sunplus_uart_probe,
> > + .remove = sunplus_uart_remove,
> > + .suspend = sunplus_uart_suspend,
> > + .resume = sunplus_uart_resume,
> > + .driver = {
> > + .name = "sunplus-uart",
>
> > + .owner = THIS_MODULE,
>
> This is done by registration call, no?
>
Ok, will remove it.
> > + .of_match_table = of_match_ptr(sp_uart_of_match),
>
> Effectively a warning (but you don't see it since COMPILE_TEST is missed).
> Hint: drop of_match_ptr() completely.
>
Ok, thanks for the information. I will add COMPILE_TEST in Kconfig.
> > +#ifdef CONFIG_PM_RUNTIME_UART
> > + .pm = sunplus_uart_pm_ops,
> > +#endif
> > + }
> > +};
>
> ...
>
> > + ret = platform_driver_register(&sunplus_uart_platform_driver);
>
> > + if (ret != 0) {
>
> Keep the same style over the driver.
>
Ok, will modify it.
> > + uart_unregister_driver(&sunplus_uart_driver);
> > + return ret;
> > + }
>
> ...
>
> > + for (;;) {
> > + status = readl(port->membase + SP_UART_LSR);
> > + if ((status & SP_UART_LSR_TXE) == SP_UART_LSR_TXE)
> > + break;
> > + cpu_relax();
> > + }
>
> real_poll_timeout*()
>
Ok, will modify it.
> --
> With Best Regards,
> Andy Shevchenko
^ permalink raw reply [flat|nested] 19+ messages in thread
* Re: [PATCH v3 1/2] dt-bindings:serial:Add bindings doc for Sunplus SoC UART Driver
2021-11-19 5:19 ` [PATCH v3 1/2] dt-bindings:serial:Add bindings doc for Sunplus SoC UART Driver Hammer Hsieh
@ 2021-11-29 0:22 ` Rob Herring
0 siblings, 0 replies; 19+ messages in thread
From: Rob Herring @ 2021-11-29 0:22 UTC (permalink / raw)
To: Hammer Hsieh
Cc: Hammer Hsieh, p.zabel, linux-kernel, devicetree, wells.lu,
robh+dt, tony.huang, linux-serial, jirislaby, gregkh
On Fri, 19 Nov 2021 13:19:22 +0800, Hammer Hsieh wrote:
> Add bindings doc for Sunplus SoC UART Driver
>
> Signed-off-by: Hammer Hsieh <hammer.hsieh@sunplus.com>
> ---
> Changes in v3:
> - Modify yaml file based on uart driver (remove dma function).
>
> .../bindings/serial/sunplus,sp7021-uart.yaml | 58 ++++++++++++++++++++++
> MAINTAINERS | 5 ++
> 2 files changed, 63 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/serial/sunplus,sp7021-uart.yaml
>
Reviewed-by: Rob Herring <robh@kernel.org>
^ permalink raw reply [flat|nested] 19+ messages in thread
end of thread, other threads:[~2021-11-29 0:24 UTC | newest]
Thread overview: 19+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2021-11-01 7:48 [PATCH 0/2] Add UART driver for Suplus SP7021 SoC hammer.hsieh
2021-11-01 7:48 ` [PATCH 1/2] dt-bindings:serial:Add bindings doc for Sunplus SoC UART Driver hammer.hsieh
2021-11-01 13:20 ` Rob Herring
2021-11-01 19:34 ` Rob Herring
2021-11-01 7:48 ` [PATCH 2/2] serial:sunplus-uart:Add " hammer.hsieh
2021-11-01 7:56 ` Greg KH
2021-11-10 7:51 ` [PATCH v2 0/2] Add UART driver for Suplus SP7021 SoC Hammer Hsieh
2021-11-10 7:51 ` [PATCH v2 1/2] dt-bindings:serial:Add bindings doc for Sunplus SoC UART Driver Hammer Hsieh
2021-11-10 7:51 ` [PATCH v2 2/2] serial:sunplus-uart:Add " Hammer Hsieh
2021-11-10 9:50 ` Philipp Zabel
2021-11-11 9:45 ` Hammer Hsieh 謝宏孟
2021-11-12 8:31 ` kernel test robot
2021-11-10 16:41 ` [PATCH v2 0/2] Add UART driver for Suplus SP7021 SoC Andy Shevchenko
2021-11-19 5:19 ` [PATCH v3 " Hammer Hsieh
2021-11-19 5:19 ` [PATCH v3 1/2] dt-bindings:serial:Add bindings doc for Sunplus SoC UART Driver Hammer Hsieh
2021-11-29 0:22 ` Rob Herring
2021-11-19 5:19 ` [PATCH v3 2/2] serial:sunplus-uart:Add " Hammer Hsieh
2021-11-19 9:35 ` Andy Shevchenko
2021-11-23 3:43 ` Hammer Hsieh 謝宏孟
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).