linux-kernel.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Horatiu Vultur <horatiu.vultur@microchip.com>
To: Philipp Zabel <p.zabel@pengutronix.de>
Cc: <davem@davemloft.net>, <kuba@kernel.org>, <robh+dt@kernel.org>,
	<linux@armlinux.org.uk>, <netdev@vger.kernel.org>,
	<devicetree@vger.kernel.org>, <linux-kernel@vger.kernel.org>
Subject: Re: [PATCH net-next 2/5] net: lan966x: add the basic lan966x driver
Date: Thu, 18 Nov 2021 13:49:08 +0100	[thread overview]
Message-ID: <20211118124908.672iif6n5x23fijw@soft-dev3-1.localhost> (raw)
In-Reply-To: <cdb9c0c334823505a2ce499e36be9507112f4298.camel@pengutronix.de>

The 11/18/2021 11:19, Philipp Zabel wrote:
> 
> Hi Horatiu,
> 
> On Wed, 2021-11-17 at 22:42 +0100, Horatiu Vultur wrote:
> > > On Wed, 2021-11-17 at 10:18 +0100, Horatiu Vultur wrote:
> > > > +static int lan966x_reset_switch(struct lan966x *lan966x)
> > > > +{
> > > > +     struct reset_control *reset;
> > > > +     int val = 0;
> > > > +     int ret;
> > > > +
> > > > +     reset = devm_reset_control_get_shared(lan966x->dev, "switch");
> > > > +     if (IS_ERR(reset))
> > > > +             dev_warn(lan966x->dev, "Could not obtain switch reset: %ld\n",
> > > > +                      PTR_ERR(reset));
> > > > +     else
> > > > +             reset_control_reset(reset);
> > >
> > > According to the device tree bindings, both resets are required.
> > > I'd expect this to return on error.
> > > Is there any chance of the device working with out the switch reset
> > > being triggered?
> >
> > The only case that I see is if the bootloader triggers this switch
> > reset and then when bootloader starts the kernel and doesn't set back
> > the switch in reset. Is this a valid scenario or is a bug in the
> > bootloader?
> 
> I'm not sure. In general, the kernel shouldn't rely on the bootloader to
> have put the devices into a certain working state. If the driver will
> not work or worse, if register access could hang the system if the
> bootloader has passed control to the kernel with the switch held in
> reset and no reset control is available to the driver, it should not
> continue after failure to get the reset handle.
> 
> I'd suggest to just use:
> 
>         reset = devm_reset_control_get_shared(lan966x->dev, "switch");
>         if (IS_ERR(reset))
>                 return dev_err_probe(lan966x->dev, PTR_ERR(reset),
>                                      "Could not obtain switch reset");
>         reset_control_reset(reset);
> 
> unless you have a good reason to do otherwise.

I agree with you. I will do like you suggested in the next version.

> 
> regards
> Philipp

-- 
/Horatiu

  reply	other threads:[~2021-11-18 12:48 UTC|newest]

Thread overview: 20+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2021-11-17  9:18 [PATCH net-next 0/5] net: lan966x: Add lan966x switch driver Horatiu Vultur
2021-11-17  9:18 ` [PATCH net-next 1/5] dt-bindings: net: lan966x: Add lan966x-switch bindings Horatiu Vultur
2021-11-17  9:18 ` [PATCH net-next 2/5] net: lan966x: add the basic lan966x driver Horatiu Vultur
2021-11-17  9:52   ` Philipp Zabel
2021-11-17 21:42     ` Horatiu Vultur
2021-11-18 10:19       ` Philipp Zabel
2021-11-18 12:49         ` Horatiu Vultur [this message]
2021-11-17  9:18 ` [PATCH net-next 3/5] net: lan966x: add port module support Horatiu Vultur
2021-11-17  9:54   ` Russell King (Oracle)
2021-11-18  9:57     ` Horatiu Vultur
2021-11-18  9:59       ` Russell King (Oracle)
2021-11-18 12:59         ` Horatiu Vultur
2021-11-18 13:31           ` Russell King (Oracle)
2021-11-18 15:36             ` Sean Anderson
2021-11-18 16:11               ` Russell King (Oracle)
2021-11-18 16:18                 ` Sean Anderson
2021-11-19  8:49                   ` Horatiu Vultur
2021-11-17 11:41   ` Russell King (Oracle)
2021-11-17  9:18 ` [PATCH net-next 4/5] net: lan966x: add mactable support Horatiu Vultur
2021-11-17  9:18 ` [PATCH net-next 5/5] net: lan966x: add ethtool configuration and statistics Horatiu Vultur

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20211118124908.672iif6n5x23fijw@soft-dev3-1.localhost \
    --to=horatiu.vultur@microchip.com \
    --cc=davem@davemloft.net \
    --cc=devicetree@vger.kernel.org \
    --cc=kuba@kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux@armlinux.org.uk \
    --cc=netdev@vger.kernel.org \
    --cc=p.zabel@pengutronix.de \
    --cc=robh+dt@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).