linux-kernel.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Lucas Tanure <tanureal@opensource.cirrus.com>
To: Liam Girdwood <lgirdwood@gmail.com>,
	Mark Brown <broonie@kernel.org>, Rob Herring <robh+dt@kernel.org>,
	Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
	Jaroslav Kysela <perex@perex.cz>, Takashi Iwai <tiwai@suse.com>
Cc: <alsa-devel@alsa-project.org>, <patches@opensource.cirrus.com>,
	<devicetree@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
	Lucas Tanure <tanureal@opensource.cirrus.com>
Subject: [PATCH v6 13/16] ALSA: hda: cs35l41: Handle all external boost setups the same way
Date: Sat, 9 Apr 2022 10:13:12 +0100	[thread overview]
Message-ID: <20220409091315.1663410-14-tanureal@opensource.cirrus.com> (raw)
In-Reply-To: <20220409091315.1663410-1-tanureal@opensource.cirrus.com>

External boost enables sequences for devices with or without GPIO1 as
VSPK switch are the same if devices are put in safe mode from reset.
As a previous patch put all external boost devices into safe mode
from reset, all external boost devices can be handled in the same way
for stream open and close.

The only difference is that devices without an VSPK switch can not be
put in reset and devices with it can be put into reset if a
configuration is applied.
The function cs35l41_hda_safe_reset is created to handle the safe reset
of the chip, and as systems without VSPK switch are not supported
anymore, only the CS35L41 HDA driver should check its return.

Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
---
 sound/pci/hda/cs35l41_hda.c | 60 +++++++++++++++----------------------
 1 file changed, 24 insertions(+), 36 deletions(-)

diff --git a/sound/pci/hda/cs35l41_hda.c b/sound/pci/hda/cs35l41_hda.c
index 3294837ff606..e54b5fbb6fb5 100644
--- a/sound/pci/hda/cs35l41_hda.c
+++ b/sound/pci/hda/cs35l41_hda.c
@@ -32,33 +32,9 @@ static const struct reg_sequence cs35l41_hda_mute[] = {
 	{ CS35L41_AMP_DIG_VOL_CTRL,	0x0000A678 }, // AMP_VOL_PCM Mute
 };
 
-// only on amps where GPIO1 is used to control ext. VSPK switch
-static const struct reg_sequence cs35l41_start_ext_vspk[] = {
+static const struct reg_sequence cs35l41_safe_to_reset[] = {
 	{ 0x00000040,			0x00000055 },
 	{ 0x00000040,			0x000000AA },
-	{ 0x00007438,			0x00585941 },
-	{ 0x00007414,			0x08C82222 },
-	{ 0x0000742C,			0x00000009 },
-	{ 0x00011008,			0x00008001 },
-	{ 0x0000742C,			0x0000000F },
-	{ 0x0000742C,			0x00000079 },
-	{ 0x00007438,			0x00585941 },
-	{ CS35L41_PWR_CTRL1,		0x00000001, 3000}, // set GLOBAL_EN = 1
-	{ 0x0000742C,			0x000000F9 },
-	{ 0x00007438,			0x00580941 },
-	{ 0x00000040,			0x000000CC },
-	{ 0x00000040,			0x00000033 },
-};
-
-//only on amps where GPIO1 is used to control ext. VSPK switch
-static const struct reg_sequence cs35l41_stop_ext_vspk[] = {
-	{ 0x00000040,			0x00000055 },
-	{ 0x00000040,			0x000000AA },
-	{ 0x00007438,			0x00585941 },
-	{ 0x00002014,			0x00000000, 3000}, // set GLOBAL_EN = 0
-	{ 0x0000742C,			0x00000009 },
-	{ 0x00007438,			0x00580941 },
-	{ 0x00011008,			0x00000001 },
 	{ 0x0000393C,			0x000000C0, 6000},
 	{ 0x0000393C,			0x00000000 },
 	{ 0x00007414,			0x00C82222 },
@@ -73,7 +49,7 @@ static const struct reg_sequence cs35l41_safe_to_active[] = {
 	{ 0x0000742C,			0x0000000F },
 	{ 0x0000742C,			0x00000079 },
 	{ 0x00007438,			0x00585941 },
-	{ CS35L41_PWR_CTRL1,		0x00000001, 2000 }, // GLOBAL_EN = 1
+	{ CS35L41_PWR_CTRL1,		0x00000001, 3000 }, // GLOBAL_EN = 1
 	{ 0x0000742C,			0x000000F9 },
 	{ 0x00007438,			0x00580941 },
 	{ 0x00000040,			0x000000CC },
@@ -85,7 +61,7 @@ static const struct reg_sequence cs35l41_active_to_safe[] = {
 	{ 0x00000040,			0x000000AA },
 	{ 0x00007438,			0x00585941 },
 	{ CS35L41_PWR_CTRL1,		0x00000000 },
-	{ 0x0000742C,			0x00000009, 2000 },
+	{ 0x0000742C,			0x00000009, 3000 },
 	{ 0x00007438,			0x00580941 },
 	{ 0x00000040,			0x000000CC },
 	{ 0x00000040,			0x00000033 },
@@ -101,6 +77,21 @@ static const struct reg_sequence cs35l41_reset_to_safe[] = {
 	{ 0x00000040,			0x00000033 },
 };
 
+static bool cs35l41_hda_safe_reset(struct cs35l41_hda *cs35l41)
+{
+	switch (cs35l41->hw_cfg.bst_type) {
+	case CS35L41_EXT_BOOST:
+		regmap_write(cs35l41->regmap, CS35L41_GPIO1_CTRL1, 0x00000001);
+		regmap_multi_reg_write(cs35l41->regmap, cs35l41_safe_to_reset,
+				       ARRAY_SIZE(cs35l41_safe_to_reset));
+		return true;
+	case CS35L41_EXT_BOOST_NO_VSPK_SWITCH:
+		return false;
+	default:
+		return true;
+	}
+};
+
 static int cs35l41_hda_global_enable(struct cs35l41_hda *cs35l41, int enable)
 {
 	int ret;
@@ -113,13 +104,6 @@ static int cs35l41_hda_global_enable(struct cs35l41_hda *cs35l41, int enable)
 		usleep_range(3000, 3100);
 		break;
 	case CS35L41_EXT_BOOST:
-		if (enable)
-			ret = regmap_multi_reg_write(cs35l41->regmap, cs35l41_start_ext_vspk,
-						     ARRAY_SIZE(cs35l41_start_ext_vspk));
-		else
-			ret = regmap_multi_reg_write(cs35l41->regmap, cs35l41_stop_ext_vspk,
-						     ARRAY_SIZE(cs35l41_stop_ext_vspk));
-		break;
 	case CS35L41_EXT_BOOST_NO_VSPK_SWITCH:
 		if (enable)
 			ret = regmap_multi_reg_write(cs35l41->regmap, cs35l41_safe_to_active,
@@ -147,6 +131,8 @@ static void cs35l41_hda_playback_hook(struct device *dev, int action)
 		regmap_multi_reg_write(reg, cs35l41_hda_config, ARRAY_SIZE(cs35l41_hda_config));
 		ret = regmap_update_bits(reg, CS35L41_PWR_CTRL2,
 					 CS35L41_AMP_EN_MASK, 1 << CS35L41_AMP_EN_SHIFT);
+		if (cs35l41->hw_cfg.bst_type == CS35L41_EXT_BOOST)
+			regmap_write(reg, CS35L41_GPIO1_CTRL1, 0x00008001);
 		break;
 	case HDA_GEN_PCM_ACT_PREPARE:
 		ret = cs35l41_hda_global_enable(cs35l41, 1);
@@ -158,6 +144,8 @@ static void cs35l41_hda_playback_hook(struct device *dev, int action)
 	case HDA_GEN_PCM_ACT_CLOSE:
 		ret = regmap_update_bits(reg, CS35L41_PWR_CTRL2,
 					 CS35L41_AMP_EN_MASK, 0 << CS35L41_AMP_EN_SHIFT);
+		if (cs35l41->hw_cfg.bst_type == CS35L41_EXT_BOOST)
+			regmap_write(reg, CS35L41_GPIO1_CTRL1, 0x00000001);
 		break;
 	default:
 		dev_warn(cs35l41->dev, "Playback action not supported: %d\n", action);
@@ -517,7 +505,7 @@ int cs35l41_hda_probe(struct device *dev, const char *device_name, int id, int i
 	return 0;
 
 err:
-	if (cs35l41->hw_cfg.bst_type != CS35L41_EXT_BOOST_NO_VSPK_SWITCH)
+	if (cs35l41_hda_safe_reset(cs35l41))
 		gpiod_set_value_cansleep(cs35l41->reset_gpio, 0);
 	gpiod_put(cs35l41->reset_gpio);
 
@@ -531,7 +519,7 @@ void cs35l41_hda_remove(struct device *dev)
 
 	component_del(cs35l41->dev, &cs35l41_hda_comp_ops);
 
-	if (cs35l41->hw_cfg.bst_type != CS35L41_EXT_BOOST_NO_VSPK_SWITCH)
+	if (cs35l41_hda_safe_reset(cs35l41))
 		gpiod_set_value_cansleep(cs35l41->reset_gpio, 0);
 	gpiod_put(cs35l41->reset_gpio);
 }
-- 
2.35.1


  parent reply	other threads:[~2022-04-09  9:13 UTC|newest]

Thread overview: 25+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2022-04-09  9:12 [PATCH v6 00/16] Support external boost at CS35l41 ASoC driver Lucas Tanure
2022-04-09  9:13 ` [PATCH v6 01/16] ALSA: cs35l41: Unify hardware configuration Lucas Tanure
2022-04-09  9:13 ` [PATCH v6 02/16] ALSA: cs35l41: Check hw_config before using it Lucas Tanure
2022-04-09  9:13 ` [PATCH v6 03/16] ALSA: cs35l41: Move cs35l41_gpio_config to shared lib Lucas Tanure
2022-04-09  9:13 ` [PATCH v6 04/16] ALSA: hda: cs35l41: Fix I2S params comments Lucas Tanure
2022-04-09  9:13 ` [PATCH v6 05/16] ALSA: hda: cs35l41: Always configure the DAI Lucas Tanure
2022-04-09  9:13 ` [PATCH v6 06/16] ALSA: hda: cs35l41: Add Boost type flag Lucas Tanure
2022-04-09  9:13 ` [PATCH v6 07/16] ALSA: hda: cs35l41: Put the device into safe mode for external boost Lucas Tanure
2022-04-09  9:13 ` [PATCH v6 08/16] ALSA: hda: cs35l41: Mute the device before shutdown Lucas Tanure
2022-04-09  9:13 ` [PATCH v6 09/16] ALSA: cs35l41: Enable Internal Boost in shared lib Lucas Tanure
2022-04-09  9:13 ` [PATCH v6 10/16] ALSA: hda: cs35l41: Move boost config to initialization code Lucas Tanure
2022-04-09  9:13 ` [PATCH v6 11/16] ALSA: hda: cs35l41: Remove cs35l41_hda_reg_sequence struct Lucas Tanure
2022-04-09  9:13 ` [PATCH v6 12/16] ALSA: hda: cs35l41: Reorganize log for playback actions Lucas Tanure
2022-04-09  9:13 ` Lucas Tanure [this message]
2022-04-09  9:13 ` [PATCH v6 14/16] ALSA: hda: cs35l41: Move external boost handling to lib for ASoC use Lucas Tanure
2022-04-09  9:13 ` [PATCH v6 15/16] ASoC: cs35l41: Document CS35l41 External Boost Lucas Tanure
2022-04-12 14:44   ` Mark Brown
2022-04-09  9:13 ` [PATCH v6 16/16] ASoC: cs35l41: Support external boost Lucas Tanure
2022-04-12 14:54   ` Mark Brown
2022-04-12 10:40 ` [PATCH v6 00/16] Support external boost at CS35l41 ASoC driver Takashi Iwai
2022-04-13  7:51 ` Takashi Iwai
2022-04-13  8:10   ` tanureal
2022-04-13  8:12     ` Takashi Iwai
2022-04-13  8:21       ` Takashi Iwai
2022-04-13  8:22         ` Takashi Iwai

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20220409091315.1663410-14-tanureal@opensource.cirrus.com \
    --to=tanureal@opensource.cirrus.com \
    --cc=alsa-devel@alsa-project.org \
    --cc=broonie@kernel.org \
    --cc=devicetree@vger.kernel.org \
    --cc=krzysztof.kozlowski+dt@linaro.org \
    --cc=lgirdwood@gmail.com \
    --cc=linux-kernel@vger.kernel.org \
    --cc=patches@opensource.cirrus.com \
    --cc=perex@perex.cz \
    --cc=robh+dt@kernel.org \
    --cc=tiwai@suse.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).