[PATCH v4 0/4] arm64: mvebu: Support for Marvell 98DX2530 (and variants)

[PATCH v4 0/4] arm64: mvebu: Support for Marvell 98DX2530 (and variants)

[Chris Packham]

This series adds support for the Marvell 98DX2530 SoC which is the Control and
Management CPU integrated into the AlleyCat5/AlleyCat5X series of Marvell
switches.

The CPU core is an ARM Cortex-A55 with neon, simd and crypto extensions.

This is fairly similar to the Armada-3700 SoC so most of the required
peripherals are already supported. This series adds a devicetree and pinctrl
driver for the SoC and the RD-AC5X-32G16HVG6HLG reference board.

In the v3 series I've dropped out a few patches. The MMC stuff is more
complicated than just adding a compatible string. The mvneta changes have gone
in via net-next.

Chris Packham (4):
  dt-bindings: pinctrl: mvebu: Document bindings for AC5
  pinctrl: mvebu: pinctrl driver for 98DX2530 SoC
  arm64: dts: marvell: Add Armada 98DX2530 SoC and RD-AC5X board
  arm64: marvell: enable the 98DX2530 pinctrl driver

 .../bindings/pinctrl/marvell,ac5-pinctrl.yaml |  72 +++++
 arch/arm64/Kconfig.platforms                  |   2 +
 arch/arm64/boot/dts/marvell/Makefile          |   1 +
 .../boot/dts/marvell/armada-98dx2530.dtsi     | 302 ++++++++++++++++++
 arch/arm64/boot/dts/marvell/rd-ac5x.dts       |  82 +++++
 drivers/pinctrl/mvebu/Kconfig                 |   4 +
 drivers/pinctrl/mvebu/Makefile                |   1 +
 drivers/pinctrl/mvebu/pinctrl-ac5.c           | 261 +++++++++++++++
 8 files changed, 725 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/pinctrl/marvell,ac5-pinctrl.yaml
 create mode 100644 arch/arm64/boot/dts/marvell/armada-98dx2530.dtsi
 create mode 100644 arch/arm64/boot/dts/marvell/rd-ac5x.dts
 create mode 100644 drivers/pinctrl/mvebu/pinctrl-ac5.c

-- 
2.35.1

[PATCH v4 1/4] dt-bindings: pinctrl: mvebu: Document bindings for AC5

[Chris Packham]

Add JSON schema for marvell,ac5-pinctrl present on the Marvell 98DX2530
SoC.

Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Rob Herring <robh@kernel.org>
---

Notes:
    Changes in v4:
    - Correct v3 changelog
    - Add review from Andrew and Rob
    Changes in v3:
    - Add more pin functions
    Changes in v2:
    - Remove syscon and simple-mfd compatibles

 .../bindings/pinctrl/marvell,ac5-pinctrl.yaml | 72 +++++++++++++++++++
 1 file changed, 72 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/pinctrl/marvell,ac5-pinctrl.yaml

diff --git a/Documentation/devicetree/bindings/pinctrl/marvell,ac5-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/marvell,ac5-pinctrl.yaml
new file mode 100644
index 000000000000..a651b2744caf
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/marvell,ac5-pinctrl.yaml
@@ -0,0 +1,72 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/marvell,ac5-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Marvell AC5 pin controller
+
+maintainers:
+  - Chris Packham <chris.packham@alliedtelesis.co.nz>
+
+description:
+  Bindings for Marvell's AC5 memory-mapped pin controller.
+
+properties:
+  compatible:
+    items:
+      - const: marvell,ac5-pinctrl
+
+  reg:
+    maxItems: 1
+
+patternProperties:
+  '-pins$':
+    type: object
+    $ref: pinmux-node.yaml#
+
+    properties:
+      marvell,function:
+        $ref: "/schemas/types.yaml#/definitions/string"
+        description:
+          Indicates the function to select.
+        enum: [ dev_init_done, ge, gpio, i2c0, i2c1, int_out, led, nand, pcie, ptp, sdio,
+                spi0, spi1, synce, tsen_int, uart0, uart1, uart2, uart3, uartsd, wd_int, xg ]
+
+      marvell,pins:
+        $ref: /schemas/types.yaml#/definitions/string-array
+        description:
+          Array of MPP pins to be used for the given function.
+        minItems: 1
+        items:
+          enum: [ mpp0, mpp1, mpp2, mpp3, mpp4, mpp5, mpp6, mpp7, mpp8, mpp9,
+                  mpp10, mpp11, mpp12, mpp13, mpp14, mpp15, mpp16, mpp17, mpp18, mpp19,
+                  mpp20, mpp21, mpp22, mpp23, mpp24, mpp25, mpp26, mpp27, mpp28, mpp29,
+                  mpp30, mpp31, mpp32, mpp33, mpp34, mpp35, mpp36, mpp37, mpp38, mpp39,
+                  mpp40, mpp41, mpp42, mpp43, mpp44, mpp45 ]
+
+allOf:
+  - $ref: "pinctrl.yaml#"
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    pinctrl@80020100 {
+      compatible = "marvell,ac5-pinctrl";
+      reg = <0x80020100 0x20>;
+
+      i2c0_pins: i2c0-pins {
+        marvell,pins = "mpp26", "mpp27";
+        marvell,function = "i2c0";
+      };
+
+      i2c0_gpio: i2c0-gpio-pins {
+        marvell,pins = "mpp26", "mpp27";
+        marvell,function = "gpio";
+      };
+    };
-- 
2.35.1

[PATCH v4 2/4] pinctrl: mvebu: pinctrl driver for 98DX2530 SoC

[Chris Packham]

This pinctrl driver supports the 98DX25xx and 98DX35xx family of chips
from Marvell. It is based on the Marvell SDK with additions for various
(non-gpio) pin configurations based on the datasheet.

Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
---

Notes:
    Changes in v4:
    - None
    Changes in v3:
    - Use mmio instead of syscon
    - Add additional functions based on the datasheet
    Changes in v2:
    - Make pinctrl a child of a syscon node like the armada-7k-pinctrl

 drivers/pinctrl/mvebu/Kconfig       |   4 +
 drivers/pinctrl/mvebu/Makefile      |   1 +
 drivers/pinctrl/mvebu/pinctrl-ac5.c | 261 ++++++++++++++++++++++++++++
 3 files changed, 266 insertions(+)
 create mode 100644 drivers/pinctrl/mvebu/pinctrl-ac5.c

diff --git a/drivers/pinctrl/mvebu/Kconfig b/drivers/pinctrl/mvebu/Kconfig
index 0d12894d3ee1..aa5883f09d7b 100644
--- a/drivers/pinctrl/mvebu/Kconfig
+++ b/drivers/pinctrl/mvebu/Kconfig
@@ -45,6 +45,10 @@ config PINCTRL_ORION
 	bool
 	select PINCTRL_MVEBU
 
+config PINCTRL_AC5
+	bool
+	select PINCTRL_MVEBU
+
 config PINCTRL_ARMADA_37XX
 	bool
 	select GENERIC_PINCONF
diff --git a/drivers/pinctrl/mvebu/Makefile b/drivers/pinctrl/mvebu/Makefile
index cd082dca4482..23458ab17c53 100644
--- a/drivers/pinctrl/mvebu/Makefile
+++ b/drivers/pinctrl/mvebu/Makefile
@@ -11,3 +11,4 @@ obj-$(CONFIG_PINCTRL_ARMADA_CP110) += pinctrl-armada-cp110.o
 obj-$(CONFIG_PINCTRL_ARMADA_XP)  += pinctrl-armada-xp.o
 obj-$(CONFIG_PINCTRL_ARMADA_37XX)  += pinctrl-armada-37xx.o
 obj-$(CONFIG_PINCTRL_ORION)  += pinctrl-orion.o
+obj-$(CONFIG_PINCTRL_AC5) += pinctrl-ac5.o
diff --git a/drivers/pinctrl/mvebu/pinctrl-ac5.c b/drivers/pinctrl/mvebu/pinctrl-ac5.c
new file mode 100644
index 000000000000..292633e61129
--- /dev/null
+++ b/drivers/pinctrl/mvebu/pinctrl-ac5.c
@@ -0,0 +1,261 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Marvell ac5 pinctrl driver based on mvebu pinctrl core
+ *
+ * Copyright (C) 2021 Marvell
+ *
+ * Noam Liron <lnoam@marvell.com>
+ */
+
+#include <linux/err.h>
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/platform_device.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/pinctrl/pinctrl.h>
+
+#include "pinctrl-mvebu.h"
+
+static struct mvebu_mpp_mode ac5_mpp_modes[] = {
+	MPP_MODE(0,
+		 MPP_FUNCTION(0, "gpio",  NULL),
+		 MPP_FUNCTION(1, "sdio",  "d0"),
+		 MPP_FUNCTION(2, "nand",  "io4")),
+	MPP_MODE(1,
+		 MPP_FUNCTION(0, "gpio",  NULL),
+		 MPP_FUNCTION(1, "sdio",  "d1"),
+		 MPP_FUNCTION(2, "nand",  "io3")),
+	MPP_MODE(2,
+		 MPP_FUNCTION(0, "gpio",  NULL),
+		 MPP_FUNCTION(1, "sdio",  "d2"),
+		 MPP_FUNCTION(2, "nand",  "io2")),
+	MPP_MODE(3,
+		 MPP_FUNCTION(0, "gpio",  NULL),
+		 MPP_FUNCTION(1, "sdio",  "d3"),
+		 MPP_FUNCTION(2, "nand",  "io7")),
+	MPP_MODE(4,
+		 MPP_FUNCTION(0, "gpio",  NULL),
+		 MPP_FUNCTION(1, "sdio",  "d4"),
+		 MPP_FUNCTION(2, "nand",  "io6"),
+		 MPP_FUNCTION(3, "uart3", "txd"),
+		 MPP_FUNCTION(4, "uart2", "txd")),
+	MPP_MODE(5,
+		 MPP_FUNCTION(0, "gpio",  NULL),
+		 MPP_FUNCTION(1, "sdio",  "d5"),
+		 MPP_FUNCTION(2, "nand",  "io5"),
+		 MPP_FUNCTION(3, "uart3", "rxd"),
+		 MPP_FUNCTION(4, "uart2", "rxd")),
+	MPP_MODE(6,
+		 MPP_FUNCTION(0, "gpio",  NULL),
+		 MPP_FUNCTION(1, "sdio",  "d6"),
+		 MPP_FUNCTION(2, "nand",  "io0"),
+		 MPP_FUNCTION(3, "i2c1",  "sck")),
+	MPP_MODE(7,
+		 MPP_FUNCTION(0, "gpio",  NULL),
+		 MPP_FUNCTION(1, "sdio",  "d7"),
+		 MPP_FUNCTION(2, "nand",  "io1"),
+		 MPP_FUNCTION(3, "i2c1",  "sda")),
+	MPP_MODE(8,
+		 MPP_FUNCTION(0, "gpio",  NULL),
+		 MPP_FUNCTION(1, "sdio",  "clk"),
+		 MPP_FUNCTION(2, "nand",  "wen")),
+	MPP_MODE(9,
+		 MPP_FUNCTION(0, "gpio",  NULL),
+		 MPP_FUNCTION(1, "sdio",  "cmd"),
+		 MPP_FUNCTION(2, "nand",  "ale")),
+	MPP_MODE(10,
+		 MPP_FUNCTION(0, "gpio",  NULL),
+		 MPP_FUNCTION(1, "sdio",  "ds"),
+		 MPP_FUNCTION(2, "nand",  "cle")),
+	MPP_MODE(11,
+		 MPP_FUNCTION(0, "gpio",  NULL),
+		 MPP_FUNCTION(1, "sdio",  "rst"),
+		 MPP_FUNCTION(2, "nand",  "cen")),
+	MPP_MODE(12,
+		 MPP_FUNCTION(0, "gpio",  NULL),
+		 MPP_FUNCTION(1, "spi0",  "clk")),
+	MPP_MODE(13,
+		 MPP_FUNCTION(0, "gpio",  NULL),
+		 MPP_FUNCTION(1, "spi0",  "csn")),
+	MPP_MODE(14,
+		 MPP_FUNCTION(0, "gpio",  NULL),
+		 MPP_FUNCTION(1, "spi0",  "mosi")),
+	MPP_MODE(15,
+		 MPP_FUNCTION(0, "gpio",  NULL),
+		 MPP_FUNCTION(1, "spi0",  "miso")),
+	MPP_MODE(16,
+		 MPP_FUNCTION(0, "gpio",  NULL),
+		 MPP_FUNCTION(1, "spi0",  "wpn"),
+		 MPP_FUNCTION(2, "nand",  "ren"),
+		 MPP_FUNCTION(3, "uart1", "txd")),
+	MPP_MODE(17,
+		 MPP_FUNCTION(0, "gpio",  NULL),
+		 MPP_FUNCTION(1, "spi0",  "hold"),
+		 MPP_FUNCTION(2, "nand",  "rb"),
+		 MPP_FUNCTION(3, "uart1", "rxd")),
+	MPP_MODE(18,
+		 MPP_FUNCTION(0, "gpio",  NULL),
+		 MPP_FUNCTION(1, "tsen_int", NULL),
+		 MPP_FUNCTION(2, "uart2", "rxd"),
+		 MPP_FUNCTION(3, "wd_int", NULL)),
+	MPP_MODE(19,
+		 MPP_FUNCTION(0, "gpio",  NULL),
+		 MPP_FUNCTION(1, "dev_init_done", NULL),
+		 MPP_FUNCTION(2, "uart2", "txd")),
+	MPP_MODE(20,
+		 MPP_FUNCTION(0, "gpio",  NULL),
+		 MPP_FUNCTION(2, "i2c1",  "sck"),
+		 MPP_FUNCTION(3, "spi1",  "clk"),
+		 MPP_FUNCTION(4, "uart3", "txd")),
+	MPP_MODE(21,
+		 MPP_FUNCTION(0, "gpio",  NULL),
+		 MPP_FUNCTION(2, "i2c1",  "sda"),
+		 MPP_FUNCTION(3, "spi1",  "csn"),
+		 MPP_FUNCTION(4, "uart3", "rxd")),
+	MPP_MODE(22,
+		 MPP_FUNCTION(0, "gpio",  NULL),
+		 MPP_FUNCTION(3, "spi1",  "mosi")),
+	MPP_MODE(23,
+		 MPP_FUNCTION(0, "gpio",  NULL),
+		 MPP_FUNCTION(3, "spi1",  "miso")),
+	MPP_MODE(24,
+		 MPP_FUNCTION(0, "gpio",  NULL),
+		 MPP_FUNCTION(1, "wd_int", NULL),
+		 MPP_FUNCTION(2, "uart2", "txd"),
+		 MPP_FUNCTION(3, "uartsd", "txd")),
+	MPP_MODE(25,
+		 MPP_FUNCTION(0, "gpio",  NULL),
+		 MPP_FUNCTION(1, "int_out", NULL),
+		 MPP_FUNCTION(2, "uart2", "rxd"),
+		 MPP_FUNCTION(3, "uartsd", "rxd")),
+	MPP_MODE(26,
+		 MPP_FUNCTION(0, "gpio",  NULL),
+		 MPP_FUNCTION(1, "i2c0",  "sck"),
+		 MPP_FUNCTION(2, "ptp", "clk1"),
+		 MPP_FUNCTION(3, "uart3", "txd")),
+	MPP_MODE(27,
+		 MPP_FUNCTION(0, "gpio",  NULL),
+		 MPP_FUNCTION(1, "i2c0",  "sda"),
+		 MPP_FUNCTION(2, "ptp", "pulse"),
+		 MPP_FUNCTION(3, "uart3", "rxd")),
+	MPP_MODE(28,
+		 MPP_FUNCTION(0, "gpio",  NULL),
+		 MPP_FUNCTION(1, "xg", "mdio"),
+		 MPP_FUNCTION(2, "ge", "mdio"),
+		 MPP_FUNCTION(3, "uart3", "txd")),
+	MPP_MODE(29,
+		 MPP_FUNCTION(0, "gpio",  NULL),
+		 MPP_FUNCTION(1, "xg", "mdio"),
+		 MPP_FUNCTION(2, "ge", "mdio"),
+		 MPP_FUNCTION(3, "uart3", "rxd")),
+	MPP_MODE(30,
+		 MPP_FUNCTION(0, "gpio",  NULL),
+		 MPP_FUNCTION(1, "xg", "mdio"),
+		 MPP_FUNCTION(2, "ge", "mdio"),
+		 MPP_FUNCTION(3, "ge", "mdio")),
+	MPP_MODE(31,
+		 MPP_FUNCTION(0, "gpio",  NULL),
+		 MPP_FUNCTION(1, "xg", "mdio"),
+		 MPP_FUNCTION(2, "ge", "mdio"),
+		 MPP_FUNCTION(3, "ge", "mdio")),
+	MPP_MODE(32,
+		 MPP_FUNCTION(0, "gpio",  NULL),
+		 MPP_FUNCTION(1, "uart0", "txd")),
+	MPP_MODE(33,
+		 MPP_FUNCTION(0, "gpio",  NULL),
+		 MPP_FUNCTION(1, "uart0", "rxd"),
+		 MPP_FUNCTION(2, "ptp", "clk1"),
+		 MPP_FUNCTION(3, "ptp", "pulse")),
+	MPP_MODE(34,
+		 MPP_FUNCTION(0, "gpio",  NULL),
+		 MPP_FUNCTION(1, "ge", "mdio"),
+		 MPP_FUNCTION(2, "uart3", "rxd")),
+	MPP_MODE(35,
+		 MPP_FUNCTION(0, "gpio",  NULL),
+		 MPP_FUNCTION(1, "ge", "mdio"),
+		 MPP_FUNCTION(2, "uart3", "txd"),
+		 MPP_FUNCTION(3, "pcie", "rstoutn")),
+	MPP_MODE(36,
+		 MPP_FUNCTION(0, "gpio",  NULL),
+		 MPP_FUNCTION(1, "ptp", "clk0_tp"),
+		 MPP_FUNCTION(2, "ptp", "clk1_tp")),
+	MPP_MODE(37,
+		 MPP_FUNCTION(0, "gpio",  NULL),
+		 MPP_FUNCTION(1, "ptp", "pulse_tp"),
+		 MPP_FUNCTION(2, "wd_int", NULL)),
+	MPP_MODE(38,
+		 MPP_FUNCTION(0, "gpio",  NULL),
+		 MPP_FUNCTION(1, "synce", "clk_out0")),
+	MPP_MODE(39,
+		 MPP_FUNCTION(0, "gpio",  NULL),
+		 MPP_FUNCTION(1, "synce", "clk_out1")),
+	MPP_MODE(40,
+		 MPP_FUNCTION(0, "gpio",  NULL),
+		 MPP_FUNCTION(1, "ptp", "pclk_out0"),
+		 MPP_FUNCTION(2, "ptp", "pclk_out1")),
+	MPP_MODE(41,
+		 MPP_FUNCTION(0, "gpio",  NULL),
+		 MPP_FUNCTION(1, "ptp", "ref_clk"),
+		 MPP_FUNCTION(2, "ptp", "clk1"),
+		 MPP_FUNCTION(3, "ptp", "pulse"),
+		 MPP_FUNCTION(4, "uart2", "txd"),
+		 MPP_FUNCTION(5, "i2c1",  "sck")),
+	MPP_MODE(42,
+		 MPP_FUNCTION(0, "gpio",  NULL),
+		 MPP_FUNCTION(1, "ptp", "clk0"),
+		 MPP_FUNCTION(2, "ptp", "clk1"),
+		 MPP_FUNCTION(3, "ptp", "pulse"),
+		 MPP_FUNCTION(4, "uart2", "rxd"),
+		 MPP_FUNCTION(5, "i2c1",  "sda")),
+	MPP_MODE(43,
+		 MPP_FUNCTION(0, "gpio",  NULL),
+		 MPP_FUNCTION(1, "led", "clk")),
+	MPP_MODE(44,
+		 MPP_FUNCTION(0, "gpio",  NULL),
+		 MPP_FUNCTION(1, "led", "stb")),
+	MPP_MODE(45,
+		 MPP_FUNCTION(0, "gpio",  NULL),
+		 MPP_FUNCTION(1, "led", "data")),
+};
+
+static struct mvebu_pinctrl_soc_info ac5_pinctrl_info;
+
+static const struct of_device_id ac5_pinctrl_of_match[] = {
+	{
+		.compatible = "marvell,ac5-pinctrl",
+	},
+	{ },
+};
+
+static const struct mvebu_mpp_ctrl ac5_mpp_controls[] = {
+	MPP_FUNC_CTRL(0, 45, NULL, mvebu_mmio_mpp_ctrl), };
+
+static struct pinctrl_gpio_range ac5_mpp_gpio_ranges[] = {
+	MPP_GPIO_RANGE(0,   0,  0, 46), };
+
+static int ac5_pinctrl_probe(struct platform_device *pdev)
+{
+	struct mvebu_pinctrl_soc_info *soc = &ac5_pinctrl_info;
+
+	soc->variant = 0; /* no variants for ac5 */
+	soc->controls = ac5_mpp_controls;
+	soc->ncontrols = ARRAY_SIZE(ac5_mpp_controls);
+	soc->gpioranges = ac5_mpp_gpio_ranges;
+	soc->ngpioranges = ARRAY_SIZE(ac5_mpp_gpio_ranges);
+	soc->modes = ac5_mpp_modes;
+	soc->nmodes = ac5_mpp_controls[0].npins;
+
+	pdev->dev.platform_data = soc;
+
+	return mvebu_pinctrl_simple_mmio_probe(pdev);
+}
+
+static struct platform_driver ac5_pinctrl_driver = {
+	.driver = {
+		.name = "ac5-pinctrl",
+		.of_match_table = of_match_ptr(ac5_pinctrl_of_match),
+	},
+	.probe = ac5_pinctrl_probe,
+};
+builtin_platform_driver(ac5_pinctrl_driver);
-- 
2.35.1

[PATCH v4 3/4] arm64: dts: marvell: Add Armada 98DX2530 SoC and RD-AC5X board

[Chris Packham]

The 98DX2530 SoC is the Control and Management CPU integrated into
the Marvell 98DX25xx and 98DX35xx series of switch chip (internally
referred to as AlleyCat5 and AlleyCat5X).

These files have been taken from the Marvell SDK and lightly cleaned
up with the License and copyright retained.

Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
---

Notes:
    The Marvell SDK has a number of new compatible strings. I've brought
    through some of the drivers or where possible used an in-tree
    alternative (e.g. there is SDK code for a ac5-gpio but two instances of
    the existing marvell,orion-gpio seems to cover what is needed if you use
    an appropriate binding). I expect that there will a new series of
    patches when I get some different hardware (or additions to this series
    depending on if/when it lands).
    
    Changes in v4:
    - use 'phy-handle' instead of 'phy'
    - move status="okay" on usb nodes to board dts
    - Add review from Andrew
    Changes in v3:
    - Move memory node to board
    - Use single digit reg value for phy address
    - Remove MMC node (driver needs work)
    - Remove syscon & simple-mfd for pinctrl
    Changes in v2:
    - Make pinctrl a child node of a syscon node
    - Use marvell,armada-8k-gpio instead of orion-gpio
    - Remove nand peripheral. The Marvell SDK does have some changes for the
      ac5-nand-controller but I currently lack hardware with NAND fitted so
      I can't test it right now. I've therefore chosen to omit the node and
      not attempted to bring in the driver or binding.
    - Remove pcie peripheral. Again there are changes in the SDK and I have
      no way of testing them.
    - Remove prestera node.
    - Remove "marvell,ac5-ehci" compatible from USB node as
      "marvell,orion-ehci" is sufficient
    - Remove watchdog node. There is a buggy driver for the ac5 watchdog in
      the SDK but it needs some work so I've dropped the node for now.

 arch/arm64/boot/dts/marvell/Makefile          |   1 +
 .../boot/dts/marvell/armada-98dx2530.dtsi     | 302 ++++++++++++++++++
 arch/arm64/boot/dts/marvell/rd-ac5x.dts       |  82 +++++
 3 files changed, 385 insertions(+)
 create mode 100644 arch/arm64/boot/dts/marvell/armada-98dx2530.dtsi
 create mode 100644 arch/arm64/boot/dts/marvell/rd-ac5x.dts

diff --git a/arch/arm64/boot/dts/marvell/Makefile b/arch/arm64/boot/dts/marvell/Makefile
index 1c794cdcb8e6..3905dee558b4 100644
--- a/arch/arm64/boot/dts/marvell/Makefile
+++ b/arch/arm64/boot/dts/marvell/Makefile
@@ -24,3 +24,4 @@ dtb-$(CONFIG_ARCH_MVEBU) += cn9132-db.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += cn9132-db-B.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += cn9130-crb-A.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += cn9130-crb-B.dtb
+dtb-$(CONFIG_ARCH_MVEBU) += rd-ac5x.dtb
diff --git a/arch/arm64/boot/dts/marvell/armada-98dx2530.dtsi b/arch/arm64/boot/dts/marvell/armada-98dx2530.dtsi
new file mode 100644
index 000000000000..3b9ea69f6f8d
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/armada-98dx2530.dtsi
@@ -0,0 +1,302 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree For AC5.
+ *
+ * Copyright (C) 2021 Marvell
+ *
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+	model = "Marvell AC5 SoC";
+	compatible = "marvell,ac5";
+	interrupt-parent = <&gic>;
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	aliases {
+		serial0 = &uart0;
+		spiflash0 = &spiflash0;
+		gpio0 = &gpio0;
+		gpio1 = &gpio1;
+		ethernet0 = &eth0;
+		ethernet1 = &eth1;
+	};
+
+	psci {
+		compatible = "arm,psci-0.2";
+		method = "smc";
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>,
+				 <GIC_PPI 8 IRQ_TYPE_LEVEL_HIGH>,
+				 <GIC_PPI 10 IRQ_TYPE_LEVEL_HIGH>,
+				 <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>;
+		clock-frequency = <25000000>;
+	};
+
+	pmu {
+		compatible = "arm,armv8-pmuv3";
+		interrupts = <GIC_PPI 12 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	soc {
+		compatible = "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+		dma-ranges;
+
+		internal-regs@7f000000 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "simple-bus";
+			/* 16M internal register @ 0x7f00_0000 */
+			ranges = <0x0 0x0 0x7f000000 0x1000000>;
+			dma-coherent;
+
+			uart0: serial@12000 {
+				compatible = "snps,dw-apb-uart";
+				reg = <0x12000 0x100>;
+				reg-shift = <2>;
+				interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+				reg-io-width = <1>;
+				clock-frequency = <328000000>;
+				status = "okay";
+			};
+
+			mdio: mdio@22004 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "marvell,orion-mdio";
+				reg = <0x22004 0x4>;
+				clocks = <&core_clock>;
+			};
+
+			i2c0: i2c@11000{
+				compatible = "marvell,mv78230-i2c";
+				reg = <0x11000 0x20>;
+
+				clocks = <&core_clock>;
+				clock-names = "core";
+				interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
+				clock-frequency=<100000>;
+				status="okay";
+
+				pinctrl-names = "default", "gpio";
+				pinctrl-0 = <&i2c0_pins>;
+				pinctrl-1 = <&i2c0_gpio>;
+				scl_gpio = <&gpio0 26 GPIO_ACTIVE_HIGH>;
+				sda_gpio = <&gpio0 27 GPIO_ACTIVE_HIGH>;
+			};
+
+			i2c1: i2c@11100{
+				compatible = "marvell,mv78230-i2c";
+				reg = <0x11100 0x20>;
+
+				clocks = <&core_clock>;
+				clock-names = "core";
+				interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
+				clock-frequency=<100000>;
+				status="okay";
+
+				pinctrl-names = "default", "gpio";
+				pinctrl-0 = <&i2c1_pins>;
+				pinctrl-1 = <&i2c1_gpio>;
+				scl_gpio = <&gpio0 20 GPIO_ACTIVE_HIGH>;
+				sda_gpio = <&gpio0 21 GPIO_ACTIVE_HIGH>;
+			};
+
+			gpio0: gpio@18100 {
+				compatible = "marvell,orion-gpio";
+				reg = <0x18100 0x40>;
+				ngpios = <32>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				gpio-ranges = <&pinctrl0 0 0 32>;
+				marvell,pwm-offset = <0x1f0>;
+			};
+
+			gpio1: gpio@18140 {
+				reg = <0x18140 0x40>;
+				compatible = "marvell,orion-gpio";
+				ngpios = <14>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				gpio-ranges = <&pinctrl0 0 32 14>;
+				marvell,pwm-offset = <0x1f0>;
+			};
+		};
+
+		/*
+		 * Dedicated section for devices behind 32bit controllers so we
+		 * can configure specific DMA mapping for them
+		 */
+		behind-32bit-controller@7f000000 {
+			compatible = "simple-bus";
+			#address-cells = <0x2>;
+			#size-cells = <0x2>;
+			ranges = <0x0 0x0 0x0 0x7f000000 0x0 0x1000000>;
+			/* Host phy ram starts at 0x200M */
+			dma-ranges = <0x0 0x0 0x2 0x0 0x1 0x0>;
+			dma-coherent;
+
+			eth0: ethernet@20000 {
+				compatible = "marvell,armada-ac5-neta";
+				reg = <0x0 0x20000 0x0 0x4000>;
+				interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&core_clock>;
+				status = "disabled";
+				phy-mode = "sgmii";
+			};
+
+			eth1: ethernet@24000 {
+				compatible = "marvell,armada-ac5-neta";
+				reg = <0x0 0x24000 0x0 0x4000>;
+				interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&core_clock>;
+				status = "disabled";
+				phy-mode = "sgmii";
+			};
+
+			/* A dummy entry used for chipidea phy init */
+			usb1phy: usbphy {
+				compatible = "usb-nop-xceiv";
+				#phy-cells = <0>;
+			};
+
+			/* USB0 is a host USB */
+			usb0: usb@80000 {
+				compatible = "marvell,orion-ehci";
+				reg = <0x0 0x80000 0x0 0x500>;
+				interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
+				status = "disabled";
+			};
+
+			/* USB1 is a peripheral USB */
+			usb1: usb@a0000 {
+				reg = <0x0 0xa0000 0x0 0x500>;
+				interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
+				status = "disabled";
+			};
+		};
+
+		pinctrl0: pinctrl@80020100 {
+			compatible = "marvell,ac5-pinctrl";
+			reg = <0 0x80020100 0 0x20>;
+
+			i2c0_pins: i2c0-pins {
+				marvell,pins = "mpp26", "mpp27";
+				marvell,function = "i2c0";
+			};
+
+			i2c0_gpio: i2c0-gpio-pins {
+				marvell,pins = "mpp26", "mpp27";
+				marvell,function = "gpio";
+			};
+
+			i2c1_pins: i2c1-pins {
+				marvell,pins = "mpp20", "mpp21";
+				marvell,function = "i2c1";
+			};
+
+			i2c1_gpio: i2c1-gpio-pins {
+				marvell,pins = "mpp20", "mpp21";
+				marvell,function = "i2c1";
+			};
+		};
+
+		core_clock: core_clock@0 {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <400000000>;
+		};
+
+		axi_clock: axi_clock@0 {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <325000000>;
+		};
+
+		spi_clock: spi_clock@0 {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <200000000>;
+		};
+
+		spi0: spi@805a0000 {
+			compatible = "marvell,armada-3700-spi";
+			reg = <0x0 0x805a0000 0x0 0x50>;
+			#address-cells = <0x1>;
+			#size-cells = <0x0>;
+			clocks = <&spi_clock>;
+			interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
+			num-cs = <1>;
+			status = "disabled";
+		};
+
+		spi1: spi@805a8000 {
+			compatible = "marvell,armada-3700-spi";
+			reg = <0x0 0x805a8000 0x0 0x50>;
+			#address-cells = <0x1>;
+			#size-cells = <0x0>;
+			clocks = <&spi_clock>;
+			interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
+			num-cs = <1>;
+			status = "disabled";
+		};
+	};
+
+	gic: interrupt-controller@80600000 {
+		compatible = "arm,gic-v3";
+		#interrupt-cells = <3>;
+		interrupt-controller;
+		/*#redistributor-regions = <1>;*/
+		redistributor-stride = <0x0 0x20000>;	// 128kB stride
+		reg = <0x0 0x80600000 0x0 0x10000>, /* GICD */
+		      <0x0 0x80660000 0x0 0x40000>; /* GICR */
+		interrupts = <GIC_PPI 6 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	cpus {
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cpu-map {
+			cluster0 {
+				core0 {
+					cpu = <&CPU0>;
+				};
+				core1 {
+					cpu = <&CPU1>;
+				};
+			};
+		};
+
+		CPU0:cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,armv8";
+			reg = <0x0 0x0>;
+			enable-method = "psci";
+			next-level-cache = <&L2_0>;
+		};
+
+		CPU1:cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,armv8";
+			reg = <0x0 0x100>;
+			enable-method = "psci";
+			next-level-cache = <&L2_0>;
+		};
+
+		L2_0: l2-cache0 {
+			compatible = "cache";
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/marvell/rd-ac5x.dts b/arch/arm64/boot/dts/marvell/rd-ac5x.dts
new file mode 100644
index 000000000000..71877bc967e2
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/rd-ac5x.dts
@@ -0,0 +1,82 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree For AC5X.
+ *
+ * Copyright (C) 2021 Marvell
+ *
+ */
+/*
+ * Device Tree file for Marvell Alleycat 5X development board
+ * This board file supports the B configuration of the board
+ */
+
+/dts-v1/;
+
+#include "armada-98dx2530.dtsi"
+
+/ {
+	model = "Marvell RD-AC5X Board";
+	compatible = "marvell,ac5x", "marvell,ac5";
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x2 0x00000000 0x0 0x40000000>;
+	};
+};
+
+&mdio {
+	phy0: ethernet-phy@0 {
+		reg = <0>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	phy-handle = <&phy0>;
+};
+
+&usb0 {
+	status = "okay";
+};
+
+&usb1 {
+	status = "okay";
+};
+
+&spi0 {
+	status = "okay";
+
+	spiflash0: spi-flash@0 {
+		compatible = "spi-nor";
+		spi-max-frequency = <50000000>;
+		spi-tx-bus-width = <1>; /* 1-single, 2-dual, 4-quad */
+		spi-rx-bus-width = <1>; /* 1-single, 2-dual, 4-quad */
+		reg = <0>;
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		partition@0 {
+			label = "spi_flash_part0";
+			reg = <0x0 0x800000>;
+		};
+
+		parition@1 {
+			label = "spi_flash_part1";
+			reg = <0x800000 0x700000>;
+		};
+
+		parition@2 {
+			label = "spi_flash_part2";
+			reg = <0xF00000 0x100000>;
+		};
+	};
+};
+
+&usb1 {
+	compatible = "chipidea,usb2";
+	phys = <&usb1phy>;
+	phy-names = "usb-phy";
+	dr_mode = "peripheral";
+};
+
-- 
2.35.1

[PATCH v4 4/4] arm64: marvell: enable the 98DX2530 pinctrl driver

[Chris Packham]

This commit makes sure the drivers for the 98DX2530 pin controller is
enabled.

Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
---

Notes:
    Changes in v4:
    - None
    Changes in v3:
    - Add review from Andrew
    Changes in v2:
    - None

 arch/arm64/Kconfig.platforms | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/arch/arm64/Kconfig.platforms b/arch/arm64/Kconfig.platforms
index 21697449d762..6bbb56901794 100644
--- a/arch/arm64/Kconfig.platforms
+++ b/arch/arm64/Kconfig.platforms
@@ -183,11 +183,13 @@ config ARCH_MVEBU
 	select PINCTRL_ARMADA_37XX
 	select PINCTRL_ARMADA_AP806
 	select PINCTRL_ARMADA_CP110
+	select PINCTRL_AC5
 	help
 	  This enables support for Marvell EBU familly, including:
 	   - Armada 3700 SoC Family
 	   - Armada 7K SoC Family
 	   - Armada 8K SoC Family
+	   - 98DX2530 SoC Family
 
 config ARCH_MXC
 	bool "ARMv8 based NXP i.MX SoC family"
-- 
2.35.1

Re: [PATCH v4 0/4] arm64: mvebu: Support for Marvell 98DX2530 (and variants)

[Linus Walleij]

On Fri, Apr 15, 2022 at 1:31 AM Chris Packham
<chris.packham@alliedtelesis.co.nz> wrote:

> Chris Packham (4):
>   dt-bindings: pinctrl: mvebu: Document bindings for AC5
>   pinctrl: mvebu: pinctrl driver for 98DX2530 SoC

These two applied to the pinctrl tree for v5.19!

Funnel the rest through the SoC tree, thanks!

Yours,
Linus Walleij