[PATCH v3 1/4] dt-bindings: arm64: dts: mediatek: Add mt8195-demo board

[PATCH v3 1/4] dt-bindings: arm64: dts: mediatek: Add mt8195-demo board

[Fabien Parent]

Add bindings for the MediaTek mt8195-demo board.

Signed-off-by: Fabien Parent <fparent@baylibre.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
v3: no changes
v2:
 * move compatible next to the MT8195-EVB compatible

 Documentation/devicetree/bindings/arm/mediatek.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/arm/mediatek.yaml b/Documentation/devicetree/bindings/arm/mediatek.yaml
index ab0593c77321..024a45300da5 100644
--- a/Documentation/devicetree/bindings/arm/mediatek.yaml
+++ b/Documentation/devicetree/bindings/arm/mediatek.yaml
@@ -133,6 +133,7 @@ properties:
           - const: mediatek,mt8183
       - items:
           - enum:
+              - mediatek,mt8195-demo
               - mediatek,mt8195-evb
           - const: mediatek,mt8195
       - description: Google Burnet (HP Chromebook x360 11MK G3 EE)
-- 
2.35.2

[PATCH v3 2/4] arm64: dts: mediatek: Add device-tree for MT8195 Demo board

[Fabien Parent]

Add basic device-tree for the MT8195 Demo board. The
Demo board is made by MediaTek and has a MT8195 SoC,
associated with the MT6359 and MT6360 PMICs, and
the MT7921 connectivity chip.

The IOs available on that board are:
* 1 USB Type-C connector with DP aux mode support
* 1 USB Type-A connector
* 1 full size HDMI RX and 1 full size HDMI TX connector
* 1 uSD slot
* 40 pins header
* SPI interface header
* 1 M.2 slot
* 1 audio jack
* 1 micro-USB port for serial debug
* 2 connectors for DSI displays
* 3 connectors for CSI cameras
* 1 connector for a eDP panel
* 1 MMC storage

This commit adds basic support in order to be able to boot.

Signed-off-by: Fabien Parent <fparent@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
---
v3:
 * use plural for all pinctrl subnode names
 * reorder all nodes in alphabetical order
 * Remove invalid property for i2c6 pinctrl
 * use interrupts-extended instead of interrupts/interrupt-parent
 * rebase on top [v14,2/2] arm64: dts: Add mediatek SoC mt8195 and evaluation board
    -> https://patchwork.kernel.org/project/linux-mediatek/patch/20220411022724.11005-3-tinghan.shen@mediatek.com/

v2:
 * remove empty i2c nodes
 * remove empty spi node
 * remove unused pcie pinctrls
 * fixup node nodes to not contains underscore
 * rename mt6360 pmic node
 * move mmc1 node right after mmc0 node
 * use generic node name for gpio-keys
 * uniformize pinctrl node names

 arch/arm64/boot/dts/mediatek/Makefile        |   1 +
 arch/arm64/boot/dts/mediatek/mt8195-demo.dts | 445 +++++++++++++++++++
 2 files changed, 446 insertions(+)
 create mode 100644 arch/arm64/boot/dts/mediatek/mt8195-demo.dts

diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
index 5da29e7223e4..c7d4636a2cb7 100644
--- a/arch/arm64/boot/dts/mediatek/Makefile
+++ b/arch/arm64/boot/dts/mediatek/Makefile
@@ -38,5 +38,6 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-krane-sku0.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-krane-sku176.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-pumpkin.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt8192-evb.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-demo.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-evb.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt8516-pumpkin.dtb
diff --git a/arch/arm64/boot/dts/mediatek/mt8195-demo.dts b/arch/arm64/boot/dts/mediatek/mt8195-demo.dts
new file mode 100644
index 000000000000..def3fc26cb99
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt8195-demo.dts
@@ -0,0 +1,445 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2022 BayLibre, SAS.
+ * Author: Fabien Parent <fparent@baylibre.com>
+ */
+/dts-v1/;
+
+#include "mt8195.dtsi"
+#include "mt6359.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/mt8195-pinfunc.h>
+#include <dt-bindings/regulator/mediatek,mt6360-regulator.h>
+
+/ {
+	model = "MediaTek MT8195 demo board";
+	compatible = "mediatek,mt8195-demo", "mediatek,mt8195";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:921600n8";
+	};
+
+	firmware {
+		optee {
+			compatible = "linaro,optee-tz";
+			method = "smc";
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		input-name = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_keys_pins>;
+
+		key-0 {
+			gpios = <&pio 106 GPIO_ACTIVE_LOW>;
+			label = "volume_up";
+			linux,code = <KEY_VOLUMEUP>;
+			wakeup-source;
+			debounce-interval = <15>;
+		};
+	};
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0 0x40000000 0 0x80000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		/* 192 KiB reserved for ARM Trusted Firmware (BL31) */
+		bl31_secmon_reserved: secmon@54600000 {
+			no-map;
+			reg = <0 0x54600000 0x0 0x30000>;
+		};
+
+		/* 12 MiB reserved for OP-TEE (BL32)
+		 * +-----------------------+ 0x43e0_0000
+		 * |      SHMEM 2MiB       |
+		 * +-----------------------+ 0x43c0_0000
+		 * |        | TA_RAM  8MiB |
+		 * + TZDRAM +--------------+ 0x4340_0000
+		 * |        | TEE_RAM 2MiB |
+		 * +-----------------------+ 0x4320_0000
+		 */
+		optee_reserved: optee@43200000 {
+			no-map;
+			reg = <0 0x43200000 0 0x00c00000>;
+		};
+	};
+};
+
+&i2c6 {
+	clock-frequency = <400000>;
+	pinctrl-0 = <&i2c6_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	mt6360: pmic@34 {
+		compatible = "mediatek,mt6360";
+		reg = <0x34>;
+		interrupt-controller;
+		interrupts-extended = <&pio 101 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-names = "IRQB";
+
+		charger {
+			compatible = "mediatek,mt6360-chg";
+			richtek,vinovp-microvolt = <14500000>;
+
+			otg_vbus_regulator: usb-otg-vbus-regulator {
+				regulator-compatible = "usb-otg-vbus";
+				regulator-name = "usb-otg-vbus";
+				regulator-min-microvolt = <4425000>;
+				regulator-max-microvolt = <5825000>;
+			};
+		};
+
+		regulator {
+			compatible = "mediatek,mt6360-regulator";
+			LDO_VIN3-supply = <&mt6360_buck2>;
+
+			mt6360_buck1: buck1 {
+				regulator-compatible = "BUCK1";
+				regulator-name = "mt6360,buck1";
+				regulator-min-microvolt = <300000>;
+				regulator-max-microvolt = <1300000>;
+				regulator-allowed-modes = <MT6360_OPMODE_NORMAL
+							   MT6360_OPMODE_LP
+							   MT6360_OPMODE_ULP>;
+				regulator-always-on;
+			};
+
+			mt6360_buck2: buck2 {
+				regulator-compatible = "BUCK2";
+				regulator-name = "mt6360,buck2";
+				regulator-min-microvolt = <300000>;
+				regulator-max-microvolt = <1300000>;
+				regulator-allowed-modes = <MT6360_OPMODE_NORMAL
+							   MT6360_OPMODE_LP
+							   MT6360_OPMODE_ULP>;
+				regulator-always-on;
+			};
+
+			mt6360_ldo1: ldo1 {
+				regulator-compatible = "LDO1";
+				regulator-name = "mt6360,ldo1";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <3600000>;
+				regulator-allowed-modes = <MT6360_OPMODE_NORMAL
+							   MT6360_OPMODE_LP>;
+			};
+
+			mt6360_ldo2: ldo2 {
+				regulator-compatible = "LDO2";
+				regulator-name = "mt6360,ldo2";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <3600000>;
+				regulator-allowed-modes = <MT6360_OPMODE_NORMAL
+							   MT6360_OPMODE_LP>;
+			};
+
+			mt6360_ldo3: ldo3 {
+				regulator-compatible = "LDO3";
+				regulator-name = "mt6360,ldo3";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <3600000>;
+				regulator-allowed-modes = <MT6360_OPMODE_NORMAL
+							   MT6360_OPMODE_LP>;
+			};
+
+			mt6360_ldo5: ldo5 {
+				regulator-compatible = "LDO5";
+				regulator-name = "mt6360,ldo5";
+				regulator-min-microvolt = <2700000>;
+				regulator-max-microvolt = <3600000>;
+				regulator-allowed-modes = <MT6360_OPMODE_NORMAL
+							   MT6360_OPMODE_LP>;
+			};
+
+			mt6360_ldo6: ldo6 {
+				regulator-compatible = "LDO6";
+				regulator-name = "mt6360,ldo6";
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <2100000>;
+				regulator-allowed-modes = <MT6360_OPMODE_NORMAL
+							   MT6360_OPMODE_LP>;
+			};
+
+			mt6360_ldo7: ldo7 {
+				regulator-compatible = "LDO7";
+				regulator-name = "mt6360,ldo7";
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <2100000>;
+				regulator-allowed-modes = <MT6360_OPMODE_NORMAL
+							   MT6360_OPMODE_LP>;
+				regulator-always-on;
+			};
+		};
+	};
+};
+
+&mmc0 {
+	status = "okay";
+	pinctrl-names = "default", "state_uhs";
+	pinctrl-0 = <&mmc0_default_pins>;
+	pinctrl-1 = <&mmc0_uhs_pins>;
+	bus-width = <8>;
+	max-frequency = <200000000>;
+	cap-mmc-highspeed;
+	mmc-hs200-1_8v;
+	mmc-hs400-1_8v;
+	cap-mmc-hw-reset;
+	no-sdio;
+	no-sd;
+	hs400-ds-delay = <0x14c11>;
+	vmmc-supply = <&mt6359_vemc_1_ldo_reg>;
+	vqmmc-supply = <&mt6359_vufs_ldo_reg>;
+	non-removable;
+};
+
+&mmc1 {
+	pinctrl-names = "default", "state_uhs";
+	pinctrl-0 = <&mmc1_default_pins>;
+	pinctrl-1 = <&mmc1_uhs_pins>;
+	cd-gpios = <&pio 129 GPIO_ACTIVE_LOW>;
+	bus-width = <4>;
+	max-frequency = <200000000>;
+	cap-sd-highspeed;
+	sd-uhs-sdr50;
+	sd-uhs-sdr104;
+	vmmc-supply = <&mt6360_ldo5>;
+	vqmmc-supply = <&mt6360_ldo3>;
+	status = "okay";
+};
+
+&mt6359_vbbck_ldo_reg {
+	regulator-always-on;
+};
+
+&mt6359_vcore_buck_reg {
+	regulator-always-on;
+};
+
+&mt6359_vgpu11_buck_reg {
+	regulator-always-on;
+};
+
+&mt6359_vproc1_buck_reg {
+	regulator-always-on;
+};
+
+&mt6359_vproc2_buck_reg {
+	regulator-always-on;
+};
+
+&mt6359_vpu_buck_reg {
+	regulator-always-on;
+};
+
+&mt6359_vrf12_ldo_reg {
+	regulator-always-on;
+};
+
+&mt6359_vsram_md_ldo_reg {
+	regulator-always-on;
+};
+
+&mt6359_vsram_others_ldo_reg {
+	regulator-always-on;
+};
+
+&pio {
+	gpio_keys_pins: gpio-keys-pins {
+		pins {
+			pinmux = <PINMUX_GPIO106__FUNC_GPIO106>;
+			input-enable;
+		};
+	};
+
+	i2c6_pins: i2c6-pins {
+		pins {
+			pinmux = <PINMUX_GPIO25__FUNC_SDA6>,
+				 <PINMUX_GPIO26__FUNC_SCL6>;
+			bias-pull-up;
+		};
+	};
+
+	mmc0_default_pins: mmc0-default-pins {
+		pins-clk {
+			pinmux = <PINMUX_GPIO122__FUNC_MSDC0_CLK>;
+			drive-strength = <MTK_DRIVE_6mA>;
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+		};
+
+		pins-cmd-dat {
+			pinmux = <PINMUX_GPIO126__FUNC_MSDC0_DAT0>,
+				 <PINMUX_GPIO125__FUNC_MSDC0_DAT1>,
+				 <PINMUX_GPIO124__FUNC_MSDC0_DAT2>,
+				 <PINMUX_GPIO123__FUNC_MSDC0_DAT3>,
+				 <PINMUX_GPIO119__FUNC_MSDC0_DAT4>,
+				 <PINMUX_GPIO118__FUNC_MSDC0_DAT5>,
+				 <PINMUX_GPIO117__FUNC_MSDC0_DAT6>,
+				 <PINMUX_GPIO116__FUNC_MSDC0_DAT7>,
+				 <PINMUX_GPIO121__FUNC_MSDC0_CMD>;
+			input-enable;
+			drive-strength = <MTK_DRIVE_6mA>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+		};
+
+		pins-rst {
+			pinmux = <PINMUX_GPIO120__FUNC_MSDC0_RSTB>;
+			drive-strength = <MTK_DRIVE_6mA>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+		};
+	};
+
+	mmc0_uhs_pins: mmc0-uhs-pins {
+		pins-clk {
+			pinmux = <PINMUX_GPIO122__FUNC_MSDC0_CLK>;
+			drive-strength = <MTK_DRIVE_8mA>;
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+		};
+
+		pins-cmd-dat {
+			pinmux = <PINMUX_GPIO126__FUNC_MSDC0_DAT0>,
+				 <PINMUX_GPIO125__FUNC_MSDC0_DAT1>,
+				 <PINMUX_GPIO124__FUNC_MSDC0_DAT2>,
+				 <PINMUX_GPIO123__FUNC_MSDC0_DAT3>,
+				 <PINMUX_GPIO119__FUNC_MSDC0_DAT4>,
+				 <PINMUX_GPIO118__FUNC_MSDC0_DAT5>,
+				 <PINMUX_GPIO117__FUNC_MSDC0_DAT6>,
+				 <PINMUX_GPIO116__FUNC_MSDC0_DAT7>,
+				 <PINMUX_GPIO121__FUNC_MSDC0_CMD>;
+			input-enable;
+			drive-strength = <MTK_DRIVE_8mA>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+		};
+
+		pins-ds {
+			pinmux = <PINMUX_GPIO127__FUNC_MSDC0_DSL>;
+			drive-strength = <MTK_DRIVE_8mA>;
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+		};
+
+		pins-rst {
+			pinmux = <PINMUX_GPIO120__FUNC_MSDC0_RSTB>;
+			drive-strength = <MTK_DRIVE_8mA>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+		};
+	};
+
+	mmc1_default_pins: mmc1-default-pins {
+		pins-clk {
+			pinmux = <PINMUX_GPIO111__FUNC_MSDC1_CLK>;
+			drive-strength = <MTK_DRIVE_8mA>;
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+		};
+
+		pins-cmd-dat {
+			pinmux = <PINMUX_GPIO110__FUNC_MSDC1_CMD>,
+				 <PINMUX_GPIO112__FUNC_MSDC1_DAT0>,
+				 <PINMUX_GPIO113__FUNC_MSDC1_DAT1>,
+				 <PINMUX_GPIO114__FUNC_MSDC1_DAT2>,
+				 <PINMUX_GPIO115__FUNC_MSDC1_DAT3>;
+			input-enable;
+			drive-strength = <MTK_DRIVE_8mA>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+		};
+
+		pins-insert {
+			pinmux = <PINMUX_GPIO129__FUNC_GPIO129>;
+			bias-pull-up;
+		};
+	};
+
+	mmc1_uhs_pins: mmc1-uhs-pins {
+		pins-clk {
+			pinmux = <PINMUX_GPIO111__FUNC_MSDC1_CLK>;
+			drive-strength = <MTK_DRIVE_8mA>;
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+		};
+
+		pins-cmd-dat {
+			pinmux = <PINMUX_GPIO110__FUNC_MSDC1_CMD>,
+				 <PINMUX_GPIO112__FUNC_MSDC1_DAT0>,
+				 <PINMUX_GPIO113__FUNC_MSDC1_DAT1>,
+				 <PINMUX_GPIO114__FUNC_MSDC1_DAT2>,
+				 <PINMUX_GPIO115__FUNC_MSDC1_DAT3>;
+			input-enable;
+			drive-strength = <MTK_DRIVE_8mA>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+		};
+	};
+
+	uart0_pins: uart0-pins {
+		pins {
+			pinmux = <PINMUX_GPIO98__FUNC_UTXD0>,
+				 <PINMUX_GPIO99__FUNC_URXD0>;
+		};
+	};
+
+	uart1_pins: uart1-pins {
+		pins {
+			pinmux = <PINMUX_GPIO102__FUNC_UTXD1>,
+				 <PINMUX_GPIO103__FUNC_URXD1>;
+		};
+	};
+};
+
+
+&pmic {
+	interrupts-extended = <&pio 222 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins>;
+	status = "okay";
+};
+
+&u3phy0 {
+	status = "okay";
+};
+
+&u3phy1 {
+	status = "okay";
+};
+
+&u3phy2 {
+	status = "okay";
+};
+
+&u3phy3 {
+	status = "okay";
+};
+
+&xhci0 {
+	vusb33-supply = <&mt6359_vusb_ldo_reg>;
+	vbus-supply = <&otg_vbus_regulator>;
+	status = "okay";
+};
+
+&xhci1 {
+	vusb33-supply = <&mt6359_vusb_ldo_reg>;
+	status = "okay";
+};
+
+&xhci2 {
+	vusb33-supply = <&mt6359_vusb_ldo_reg>;
+	status = "okay";
+};
+
+&xhci3 {
+	vusb33-supply = <&mt6359_vusb_ldo_reg>;
+	status = "okay";
+};
-- 
2.35.2

[PATCH v3 3/4] arm64: defconfig: enable MT6359 regulator driver

[Fabien Parent]

The PMIC regulators are essentials to be able to
boot MediaTek MT8195 based boards to userspace.
Like the other MediaTek PMIC regulator driver,
let's enable as well the one for the MT6359 PMIC.

Signed-off-by: Fabien Parent <fparent@baylibre.com>
---
v3: no changes
v2: no changes

 arch/arm64/configs/defconfig | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
index 50aa3d75ab4f..1e521f17cb39 100644
--- a/arch/arm64/configs/defconfig
+++ b/arch/arm64/configs/defconfig
@@ -644,6 +644,7 @@ CONFIG_REGULATOR_MAX77620=y
 CONFIG_REGULATOR_MAX8973=y
 CONFIG_REGULATOR_MP8859=y
 CONFIG_REGULATOR_MT6358=y
+CONFIG_REGULATOR_MT6359=y
 CONFIG_REGULATOR_MT6397=y
 CONFIG_REGULATOR_PCA9450=y
 CONFIG_REGULATOR_PF8X00=y
-- 
2.35.2

[PATCH v3 4/4] arm64: defconfig: enable some mt6360 PMIC drivers

[Fabien Parent]

Enable the charger and regulator driver for the
MT6360 PMIC. These drivers are essential for
some MediaTek MT8195 based boards to boot properly.

Signed-off-by: Fabien Parent <fparent@baylibre.com>
---
v3: no changes
v2: no changes

 arch/arm64/configs/defconfig | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
index 1e521f17cb39..3848246f6727 100644
--- a/arch/arm64/configs/defconfig
+++ b/arch/arm64/configs/defconfig
@@ -565,6 +565,7 @@ CONFIG_SYSCON_REBOOT_MODE=y
 CONFIG_BATTERY_SBS=m
 CONFIG_BATTERY_BQ27XXX=y
 CONFIG_BATTERY_MAX17042=m
+CONFIG_CHARGER_MT6360=m
 CONFIG_CHARGER_BQ25890=m
 CONFIG_CHARGER_BQ25980=m
 CONFIG_SENSORS_ARM_SCMI=y
@@ -625,6 +626,7 @@ CONFIG_MFD_EXYNOS_LPASS=m
 CONFIG_MFD_HI6421_PMIC=y
 CONFIG_MFD_HI655X_PMIC=y
 CONFIG_MFD_MAX77620=y
+CONFIG_MFD_MT6360=y
 CONFIG_MFD_MT6397=y
 CONFIG_MFD_SPMI_PMIC=y
 CONFIG_MFD_RK808=y
@@ -645,6 +647,7 @@ CONFIG_REGULATOR_MAX8973=y
 CONFIG_REGULATOR_MP8859=y
 CONFIG_REGULATOR_MT6358=y
 CONFIG_REGULATOR_MT6359=y
+CONFIG_REGULATOR_MT6360=y
 CONFIG_REGULATOR_MT6397=y
 CONFIG_REGULATOR_PCA9450=y
 CONFIG_REGULATOR_PF8X00=y
-- 
2.35.2