* [PATCH v3 1/2] usb: serial: option: Add Fibocom L610 modem
@ 2022-04-25 14:34 sven
2022-04-25 14:34 ` [PATCH v3 2/2] usb: serial: option: Add Fibocom MA510 modem sven
2022-05-05 11:40 ` [PATCH v3 1/2] usb: serial: option: Add Fibocom L610 modem Johan Hovold
0 siblings, 2 replies; 3+ messages in thread
From: sven @ 2022-04-25 14:34 UTC (permalink / raw)
To: linux-usb; +Cc: Sven Schwermer, linux-kernel, johan
From: Sven Schwermer <sven.schwermer@disruptive-technologies.com>
The L610 modem has 3 USB configurations that are configurable via the AT
command AT+GTUSBMODE={31,32,33} which make the modem enumerate with the
following interfaces, respectively:
31: Modem + NV + MOS + Diag + LOG + AT + AT
32: ECM + Modem + NV + MOS + Diag + LOG + AT + AT
33: RNDIS + Modem + NV + MOS + Diag + LOG + AT + AT
A detailed description of the USB configuration for each mode follows:
+GTUSBMODE: 31
--------------
T: Bus=03 Lev=01 Prnt=01 Port=06 Cnt=04 Dev#=124 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1782 ProdID=4d10 Rev= 0.00
S: Manufacturer=FIBOCOM
S: Product=L610
C:* #Ifs= 7 Cfg#= 1 Atr=e0 MxPwr=400mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
+GTUSBMODE: 32
--------------
T: Bus=03 Lev=01 Prnt=01 Port=06 Cnt=04 Dev#=122 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1782 ProdID=4d11 Rev= 0.00
S: Manufacturer=FIBOCOM
S: Product=L610
C:* #Ifs= 9 Cfg#= 1 Atr=e0 MxPwr=400mA
A: FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=06 Prot=00
I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=00 Driver=cdc_ether
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 7 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 8 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=08(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
+GTUSBMODE: 33
--------------
T: Bus=03 Lev=01 Prnt=01 Port=06 Cnt=04 Dev#=126 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1782 ProdID=4d11 Rev= 0.00
S: Manufacturer=FIBOCOM
S: Product=L610
C:* #Ifs= 9 Cfg#= 1 Atr=e0 MxPwr=400mA
A: FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=03
I:* If#= 0 Alt= 0 #EPs= 1 Cls=e0(wlcon) Sub=01 Prot=03 Driver=rndis_host
E: Ad=82(I) Atr=03(Int.) MxPS= 8 Ivl=4096ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=rndis_host
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 7 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 8 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=08(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Sven Schwermer <sven.schwermer@disruptive-technologies.com>
---
V2 -> V3: Add this changelog
V1 -> V2: Use USB_DEVICE_INTERFACE_CLASS, add comments
drivers/usb/serial/option.c | 2 ++
1 file changed, 2 insertions(+)
diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c
index e7755d9cfc61..e0af45e3a6f7 100644
--- a/drivers/usb/serial/option.c
+++ b/drivers/usb/serial/option.c
@@ -2111,6 +2111,8 @@ static const struct usb_device_id option_ids[] = {
.driver_info = RSVD(3) },
{ USB_DEVICE(0x1508, 0x1001), /* Fibocom NL668 (IOT version) */
.driver_info = RSVD(4) | RSVD(5) | RSVD(6) },
+ { USB_DEVICE(0x1782, 0x4d10) }, /* Fibocom L610 (AT mode) */
+ { USB_DEVICE_INTERFACE_CLASS(0x1782, 0x4d11, 0xff) }, /* Fibocom L610 (ECM/RNDIS mode) */
{ USB_DEVICE(0x2cb7, 0x0104), /* Fibocom NL678 series */
.driver_info = RSVD(4) | RSVD(5) },
{ USB_DEVICE_INTERFACE_CLASS(0x2cb7, 0x0105, 0xff), /* Fibocom NL678 series */
--
2.36.0
^ permalink raw reply related [flat|nested] 3+ messages in thread
* [PATCH v3 2/2] usb: serial: option: Add Fibocom MA510 modem
2022-04-25 14:34 [PATCH v3 1/2] usb: serial: option: Add Fibocom L610 modem sven
@ 2022-04-25 14:34 ` sven
2022-05-05 11:40 ` [PATCH v3 1/2] usb: serial: option: Add Fibocom L610 modem Johan Hovold
1 sibling, 0 replies; 3+ messages in thread
From: sven @ 2022-04-25 14:34 UTC (permalink / raw)
To: linux-usb; +Cc: Sven Schwermer, linux-kernel, johan
From: Sven Schwermer <sven.schwermer@disruptive-technologies.com>
The MA510 modem has 3 USB configurations that are configurable via the AT
command AT+GTUSBMODE={30,31,32} which make the modem enumerate with the
following interfaces, respectively:
30: Diag + QDSS + Modem + RMNET
31: Diag + Modem + AT + ECM
32: Modem + AT + ECM
The first configuration (30) reuses u-blox R410M's VID/PID with
identical interface configuration.
A detailed description of the USB configuration for each mode follows:
+GTUSBMODE: 30
--------------
T: Bus=03 Lev=01 Prnt=01 Port=06 Cnt=04 Dev#= 19 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=05c6 ProdID=90b2 Rev= 0.00
S: Manufacturer=Fibocom MA510 Modem
S: Product=Fibocom MA510 Modem
S: SerialNumber=55e2695b
C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E: Ad=85(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
+GTUSBMODE: 31
--------------
T: Bus=03 Lev=01 Prnt=01 Port=06 Cnt=04 Dev#= 99 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=2cb7 ProdID=0106 Rev= 0.00
S: Manufacturer=Fibocom MA510 Modem
S: Product=Fibocom MA510 Modem
S: SerialNumber=55e2695b
C:* #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
A: FirstIf#= 3 IfCount= 2 Cls=02(comm.) Sub=00 Prot=00
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=82(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fe Prot=ff Driver=option
E: Ad=84(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=00 Driver=cdc_ether
E: Ad=86(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
I: If#= 4 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
I:* If#= 4 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
+GTUSBMODE: 32
--------------
T: Bus=03 Lev=01 Prnt=01 Port=06 Cnt=04 Dev#=100 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=2cb7 ProdID=010a Rev= 0.00
S: Manufacturer=Fibocom MA510 Modem
S: Product=Fibocom MA510 Modem
S: SerialNumber=55e2695b
C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=500mA
A: FirstIf#= 2 IfCount= 2 Cls=02(comm.) Sub=00 Prot=00
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=fe Prot=ff Driver=option
E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=00 Driver=cdc_ether
E: Ad=85(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
I: If#= 3 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
I:* If#= 3 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Sven Schwermer <sven.schwermer@disruptive-technologies.com>
---
V2 -> V3: Add this changelog
V1 -> V2: Use USB_DEVICE_INTERFACE_CLASS, add comments
drivers/usb/serial/option.c | 2 ++
1 file changed, 2 insertions(+)
diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c
index e0af45e3a6f7..d9c2eaf09901 100644
--- a/drivers/usb/serial/option.c
+++ b/drivers/usb/serial/option.c
@@ -2117,6 +2117,8 @@ static const struct usb_device_id option_ids[] = {
.driver_info = RSVD(4) | RSVD(5) },
{ USB_DEVICE_INTERFACE_CLASS(0x2cb7, 0x0105, 0xff), /* Fibocom NL678 series */
.driver_info = RSVD(6) },
+ { USB_DEVICE_INTERFACE_CLASS(0x2cb7, 0x0106, 0xff) }, /* Fibocom MA510 (ECM mode w/ diag intf.) */
+ { USB_DEVICE_INTERFACE_CLASS(0x2cb7, 0x010a, 0xff) }, /* Fibocom MA510 (ECM mode) */
{ USB_DEVICE_AND_INTERFACE_INFO(0x2cb7, 0x010b, 0xff, 0xff, 0x30) }, /* Fibocom FG150 Diag */
{ USB_DEVICE_AND_INTERFACE_INFO(0x2cb7, 0x010b, 0xff, 0, 0) }, /* Fibocom FG150 AT */
{ USB_DEVICE_INTERFACE_CLASS(0x2cb7, 0x01a0, 0xff) }, /* Fibocom NL668-AM/NL652-EU (laptop MBIM) */
--
2.36.0
^ permalink raw reply related [flat|nested] 3+ messages in thread
* Re: [PATCH v3 1/2] usb: serial: option: Add Fibocom L610 modem
2022-04-25 14:34 [PATCH v3 1/2] usb: serial: option: Add Fibocom L610 modem sven
2022-04-25 14:34 ` [PATCH v3 2/2] usb: serial: option: Add Fibocom MA510 modem sven
@ 2022-05-05 11:40 ` Johan Hovold
1 sibling, 0 replies; 3+ messages in thread
From: Johan Hovold @ 2022-05-05 11:40 UTC (permalink / raw)
To: sven; +Cc: linux-usb, Sven Schwermer, linux-kernel
On Mon, Apr 25, 2022 at 04:34:49PM +0200, sven@svenschwermer.de wrote:
> From: Sven Schwermer <sven.schwermer@disruptive-technologies.com>
>
> The L610 modem has 3 USB configurations that are configurable via the AT
> command AT+GTUSBMODE={31,32,33} which make the modem enumerate with the
> following interfaces, respectively:
>
> 31: Modem + NV + MOS + Diag + LOG + AT + AT
> 32: ECM + Modem + NV + MOS + Diag + LOG + AT + AT
> 33: RNDIS + Modem + NV + MOS + Diag + LOG + AT + AT
>
> A detailed description of the USB configuration for each mode follows:
[...]
> Signed-off-by: Sven Schwermer <sven.schwermer@disruptive-technologies.com>
> ---
> V2 -> V3: Add this changelog
> V1 -> V2: Use USB_DEVICE_INTERFACE_CLASS, add comments
Perfect, thanks for the update!
> drivers/usb/serial/option.c | 2 ++
> 1 file changed, 2 insertions(+)
>
> diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c
> index e7755d9cfc61..e0af45e3a6f7 100644
> --- a/drivers/usb/serial/option.c
> +++ b/drivers/usb/serial/option.c
> @@ -2111,6 +2111,8 @@ static const struct usb_device_id option_ids[] = {
> .driver_info = RSVD(3) },
> { USB_DEVICE(0x1508, 0x1001), /* Fibocom NL668 (IOT version) */
> .driver_info = RSVD(4) | RSVD(5) | RSVD(6) },
> + { USB_DEVICE(0x1782, 0x4d10) }, /* Fibocom L610 (AT mode) */
> + { USB_DEVICE_INTERFACE_CLASS(0x1782, 0x4d11, 0xff) }, /* Fibocom L610 (ECM/RNDIS mode) */
> { USB_DEVICE(0x2cb7, 0x0104), /* Fibocom NL678 series */
> .driver_info = RSVD(4) | RSVD(5) },
> { USB_DEVICE_INTERFACE_CLASS(0x2cb7, 0x0105, 0xff), /* Fibocom NL678 series */
Both patches now applied.
Johan
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2022-05-05 11:40 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2022-04-25 14:34 [PATCH v3 1/2] usb: serial: option: Add Fibocom L610 modem sven
2022-04-25 14:34 ` [PATCH v3 2/2] usb: serial: option: Add Fibocom MA510 modem sven
2022-05-05 11:40 ` [PATCH v3 1/2] usb: serial: option: Add Fibocom L610 modem Johan Hovold
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).