[PATCH v3] thermal: rcar_gen3_thermal: improve logging during probe

[PATCH v3] thermal: rcar_gen3_thermal: improve logging during probe

[Wolfram Sang]

When setting up a new board, a plain "Can't register thermal zone"
didn't help me much because the thermal zones in DT were all fine. I
just had a sensor entry too much in the parent TSC node. Reword the
failure/success messages to contain the sensor number to make it easier
to understand which sensor is affected. Example output now:

rcar_gen3_thermal e6198000.thermal: Sensor 0: Loaded 1 trip points
rcar_gen3_thermal e6198000.thermal: Sensor 1: Loaded 1 trip points
rcar_gen3_thermal e6198000.thermal: Sensor 2: Loaded 1 trip points
rcar_gen3_thermal e6198000.thermal: Sensor 3: Can't register thermal zone

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
---

Change since v2:

* don't add plural-'s' at runtime to allow for a greppable string
  (Thanks, Niklas!)

 drivers/thermal/rcar_gen3_thermal.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/thermal/rcar_gen3_thermal.c b/drivers/thermal/rcar_gen3_thermal.c
index ccdf8a24ddc7..cda7c52f2319 100644
--- a/drivers/thermal/rcar_gen3_thermal.c
+++ b/drivers/thermal/rcar_gen3_thermal.c
@@ -511,7 +511,7 @@ static int rcar_gen3_thermal_probe(struct platform_device *pdev)
 		zone = devm_thermal_zone_of_sensor_register(dev, i, tsc,
 							    &rcar_gen3_tz_of_ops);
 		if (IS_ERR(zone)) {
-			dev_err(dev, "Can't register thermal zone\n");
+			dev_err(dev, "Sensor %u: Can't register thermal zone\n", i);
 			ret = PTR_ERR(zone);
 			goto error_unregister;
 		}
@@ -533,7 +533,7 @@ static int rcar_gen3_thermal_probe(struct platform_device *pdev)
 		if (ret < 0)
 			goto error_unregister;
 
-		dev_info(dev, "TSC%u: Loaded %d trip points\n", i, ret);
+		dev_info(dev, "Sensor %u: Loaded %d trip points\n", i, ret);
 	}
 
 	if (!priv->num_tscs) {
-- 
2.35.1

Re: [PATCH v3] thermal: rcar_gen3_thermal: improve logging during probe

[Niklas Söderlund]

Hi Wolfram,

Thanks for your work.

On 2022-06-10 22:04:59 +0200, Wolfram Sang wrote:
> When setting up a new board, a plain "Can't register thermal zone"
> didn't help me much because the thermal zones in DT were all fine. I
> just had a sensor entry too much in the parent TSC node. Reword the
> failure/success messages to contain the sensor number to make it easier
> to understand which sensor is affected. Example output now:
> 
> rcar_gen3_thermal e6198000.thermal: Sensor 0: Loaded 1 trip points
> rcar_gen3_thermal e6198000.thermal: Sensor 1: Loaded 1 trip points
> rcar_gen3_thermal e6198000.thermal: Sensor 2: Loaded 1 trip points
> rcar_gen3_thermal e6198000.thermal: Sensor 3: Can't register thermal zone
> 
> Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>

Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>

> ---
> 
> Change since v2:
> 
> * don't add plural-'s' at runtime to allow for a greppable string
>   (Thanks, Niklas!)
> 
>  drivers/thermal/rcar_gen3_thermal.c | 4 ++--
>  1 file changed, 2 insertions(+), 2 deletions(-)
> 
> diff --git a/drivers/thermal/rcar_gen3_thermal.c b/drivers/thermal/rcar_gen3_thermal.c
> index ccdf8a24ddc7..cda7c52f2319 100644
> --- a/drivers/thermal/rcar_gen3_thermal.c
> +++ b/drivers/thermal/rcar_gen3_thermal.c
> @@ -511,7 +511,7 @@ static int rcar_gen3_thermal_probe(struct platform_device *pdev)
>  		zone = devm_thermal_zone_of_sensor_register(dev, i, tsc,
>  							    &rcar_gen3_tz_of_ops);
>  		if (IS_ERR(zone)) {
> -			dev_err(dev, "Can't register thermal zone\n");
> +			dev_err(dev, "Sensor %u: Can't register thermal zone\n", i);
>  			ret = PTR_ERR(zone);
>  			goto error_unregister;
>  		}
> @@ -533,7 +533,7 @@ static int rcar_gen3_thermal_probe(struct platform_device *pdev)
>  		if (ret < 0)
>  			goto error_unregister;
>  
> -		dev_info(dev, "TSC%u: Loaded %d trip points\n", i, ret);
> +		dev_info(dev, "Sensor %u: Loaded %d trip points\n", i, ret);
>  	}
>  
>  	if (!priv->num_tscs) {
> -- 
> 2.35.1
> 

-- 
Kind Regards,
Niklas Söderlund

Re: [PATCH v3] thermal: rcar_gen3_thermal: improve logging during probe

[Geert Uytterhoeven]

On Fri, Jun 10, 2022 at 10:08 PM Wolfram Sang
<wsa+renesas@sang-engineering.com> wrote:
> When setting up a new board, a plain "Can't register thermal zone"
> didn't help me much because the thermal zones in DT were all fine. I
> just had a sensor entry too much in the parent TSC node. Reword the
> failure/success messages to contain the sensor number to make it easier
> to understand which sensor is affected. Example output now:
>
> rcar_gen3_thermal e6198000.thermal: Sensor 0: Loaded 1 trip points
> rcar_gen3_thermal e6198000.thermal: Sensor 1: Loaded 1 trip points
> rcar_gen3_thermal e6198000.thermal: Sensor 2: Loaded 1 trip points
> rcar_gen3_thermal e6198000.thermal: Sensor 3: Can't register thermal zone
>
> Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
> ---
>
> Change since v2:
>
> * don't add plural-'s' at runtime to allow for a greppable string
>   (Thanks, Niklas!)

Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>

Gr{oetje,eeting}s,

                        Geert

--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
                                -- Linus Torvalds

Re: [PATCH v3] thermal: rcar_gen3_thermal: improve logging during probe

[Daniel Lezcano]

On 10/06/2022 22:04, Wolfram Sang wrote:
> When setting up a new board, a plain "Can't register thermal zone"
> didn't help me much because the thermal zones in DT were all fine. I
> just had a sensor entry too much in the parent TSC node. Reword the
> failure/success messages to contain the sensor number to make it easier
> to understand which sensor is affected. Example output now:
> 
> rcar_gen3_thermal e6198000.thermal: Sensor 0: Loaded 1 trip points
> rcar_gen3_thermal e6198000.thermal: Sensor 1: Loaded 1 trip points
> rcar_gen3_thermal e6198000.thermal: Sensor 2: Loaded 1 trip points
> rcar_gen3_thermal e6198000.thermal: Sensor 3: Can't register thermal zone
> 
> Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>

Applied, thanks


-- 
<http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs

Follow Linaro:  <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog