* [PATCH v4 0/2] arm64: ti: k3-am62: Enable audio output
@ 2022-06-20 10:27 Jai Luthra
2022-06-20 10:27 ` [PATCH v4 1/2] arm64: dts: ti: k3-am62-main: Add McASP nodes Jai Luthra
` (2 more replies)
0 siblings, 3 replies; 6+ messages in thread
From: Jai Luthra @ 2022-06-20 10:27 UTC (permalink / raw)
To: Nishanth Menon, Vignesh Raghavendra, Rob Herring, Krzysztof Kozlowski
Cc: linux-kernel, linux-arm-kernel, devicetree, Jayesh Choudhary, Jai Luthra
This patch series adds support for audio output via headphone jack on the
AM62-SK board. The jack is wired to TLV320AIC3106 (codec), which is connected
to McASP (serializer).
The same 3.5mm jack can be used for combined playback+recording, but audio
input is currently disabled on McASP until further testing and debugging.
v4:
Use audio-friendly 96Mhz source as clock parent for mcasp
v3:
Fix regulator, clock and codec node names
v2:
Move out the patch for sound/soc/ti/davinici-mcasp.c into a separate series
v3: https://lore.kernel.org/all/20220427085053.14964-1-j-luthra@ti.com/
v2: https://lore.kernel.org/all/20220422060052.8548-1-j-luthra@ti.com/
v1: https://lore.kernel.org/all/20220421132224.8601-1-j-luthra@ti.com/
Jai Luthra (1):
arm64: dts: ti: k3-am625-sk: Add audio output support
Jayesh Choudhary (1):
arm64: dts: ti: k3-am62-main: Add McASP nodes
arch/arm64/boot/dts/ti/k3-am62-main.dtsi | 57 +++++++++++++++
arch/arm64/boot/dts/ti/k3-am625-sk.dts | 89 ++++++++++++++++++++++++
2 files changed, 146 insertions(+)
--
2.17.1
^ permalink raw reply [flat|nested] 6+ messages in thread
* [PATCH v4 1/2] arm64: dts: ti: k3-am62-main: Add McASP nodes
2022-06-20 10:27 [PATCH v4 0/2] arm64: ti: k3-am62: Enable audio output Jai Luthra
@ 2022-06-20 10:27 ` Jai Luthra
2022-06-20 10:27 ` [PATCH v4 2/2] arm64: dts: ti: am625-sk: Add audio output support Jai Luthra
2022-06-20 10:27 ` [PATCH v4 2/2] arm64: dts: ti: k3-am625-sk: " Jai Luthra
2 siblings, 0 replies; 6+ messages in thread
From: Jai Luthra @ 2022-06-20 10:27 UTC (permalink / raw)
To: Nishanth Menon, Vignesh Raghavendra, Rob Herring, Krzysztof Kozlowski
Cc: linux-kernel, linux-arm-kernel, devicetree, Jayesh Choudhary, Jai Luthra
From: Jayesh Choudhary <j-choudhary@ti.com>
Add the nodes for McASP 0-2.
Use the audio-friendly 96MHz main_1_hsdivout6_clk as clock parent
instead of the default 100Mhz main_2_hsdivout8_clk source.
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
---
arch/arm64/boot/dts/ti/k3-am62-main.dtsi | 57 ++++++++++++++++++++++++
1 file changed, 57 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-am62-main.dtsi b/arch/arm64/boot/dts/ti/k3-am62-main.dtsi
index d08abad0bcf4..726f31a880ad 100644
--- a/arch/arm64/boot/dts/ti/k3-am62-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am62-main.dtsi
@@ -571,4 +571,61 @@
interrupt-names = "int0", "int1";
bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
};
+
+ mcasp0: mcasp@2b00000 {
+ compatible = "ti,am33xx-mcasp-audio";
+ reg = <0x00 0x02b00000 0x00 0x2000>,
+ <0x00 0x02b08000 0x00 0x400>;
+ reg-names = "mpu","dat";
+ interrupts = <GIC_SPI 236 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 235 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "tx", "rx";
+
+ dmas = <&main_bcdma 0 0xc500 0>, <&main_bcdma 0 0x4500 0>;
+ dma-names = "tx", "rx";
+
+ clocks = <&k3_clks 190 0>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 190 0>;
+ assigned-clock-parents = <&k3_clks 190 2>;
+ power-domains = <&k3_pds 190 TI_SCI_PD_EXCLUSIVE>;
+ };
+
+ mcasp1: mcasp@2b10000 {
+ compatible = "ti,am33xx-mcasp-audio";
+ reg = <0x00 0x02b10000 0x00 0x2000>,
+ <0x00 0x02b18000 0x00 0x400>;
+ reg-names = "mpu","dat";
+ interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 237 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "tx", "rx";
+
+ dmas = <&main_bcdma 0 0xc501 0>, <&main_bcdma 0 0x4501 0>;
+ dma-names = "tx", "rx";
+
+ clocks = <&k3_clks 191 0>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 191 0>;
+ assigned-clock-parents = <&k3_clks 191 2>;
+ power-domains = <&k3_pds 191 TI_SCI_PD_EXCLUSIVE>;
+ };
+
+ mcasp2: mcasp@2b20000 {
+ compatible = "ti,am33xx-mcasp-audio";
+ reg = <0x00 0x02b20000 0x00 0x2000>,
+ <0x00 0x02b28000 0x00 0x400>;
+ reg-names = "mpu","dat";
+ interrupts = <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 239 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "tx", "rx";
+
+ dmas = <&main_bcdma 0 0xc502 0>, <&main_bcdma 0 0x4502 0>;
+ dma-names = "tx", "rx";
+
+ clocks = <&k3_clks 192 0>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 192 0>;
+ assigned-clock-parents = <&k3_clks 192 2>;
+ power-domains = <&k3_pds 192 TI_SCI_PD_EXCLUSIVE>;
+ };
};
--
2.17.1
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH v4 2/2] arm64: dts: ti: am625-sk: Add audio output support
2022-06-20 10:27 [PATCH v4 0/2] arm64: ti: k3-am62: Enable audio output Jai Luthra
2022-06-20 10:27 ` [PATCH v4 1/2] arm64: dts: ti: k3-am62-main: Add McASP nodes Jai Luthra
@ 2022-06-20 10:27 ` Jai Luthra
2022-06-20 10:35 ` Jai Luthra
2022-06-20 10:27 ` [PATCH v4 2/2] arm64: dts: ti: k3-am625-sk: " Jai Luthra
2 siblings, 1 reply; 6+ messages in thread
From: Jai Luthra @ 2022-06-20 10:27 UTC (permalink / raw)
To: Nishanth Menon, Vignesh Raghavendra, Rob Herring, Krzysztof Kozlowski
Cc: linux-kernel, linux-arm-kernel, devicetree, Jayesh Choudhary, Jai Luthra
Add nodes for audio codec and sound card, enable the audio serializer
(McASP1) under use and update pinmux. Disable all other McASP nodes.
Audio input is currently not working properly, so the RX port on McASP1
is disabled for now, until the issue is debugged.
The serializer is shared between HDMI and codec. By default codec is
used for output, but it can be toggled to HDMI using a FET switch
connected to the MCASP1_FET_SEL (J24) header on the board.
Signed-off-by: Jai Luthra <j-luthra@ti.com>
---
arch/arm64/boot/dts/ti/k3-am625-sk.dts | 89 ++++++++++++++++++++++++++
1 file changed, 89 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-am625-sk.dts b/arch/arm64/boot/dts/ti/k3-am625-sk.dts
index 39fb1d763037..a502b7ac48d4 100644
--- a/arch/arm64/boot/dts/ti/k3-am625-sk.dts
+++ b/arch/arm64/boot/dts/ti/k3-am625-sk.dts
@@ -121,6 +121,46 @@
<3300000 0x1>;
};
+ vcc_1v8: regulator-5 {
+ /* output of TPS6282518DMQ */
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vcc_3v3_sys>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ tlv320_mclk: clk-0 {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <12288000>;
+ };
+
+ sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,name = "AM62x-SKEVM";
+ simple-audio-card,widgets =
+ "Headphone", "Headphone Jack";
+ simple-audio-card,routing =
+ "Headphone Jack", "HPLOUT",
+ "Headphone Jack", "HPROUT";
+ simple-audio-card,format = "dsp_b";
+ simple-audio-card,bitclock-master = <&sound_master>;
+ simple-audio-card,frame-master = <&sound_master>;
+ simple-audio-card,bitclock-inversion;
+
+ simple-audio-card,cpu {
+ sound-dai = <&mcasp1>;
+ };
+
+ sound_master: simple-audio-card,codec {
+ sound-dai = <&tlv320aic3106>;
+ clocks = <&tlv320_mclk>;
+ };
+ };
+
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
@@ -266,6 +306,15 @@
AM62X_IOPAD(0x01d4, PIN_INPUT, 7) /* (B15) UART0_RTSn.GPIO1_23 */
>;
};
+
+ main_mcasp1_pins_default: main-mcasp1-pins-default {
+ pinctrl-single,pins = <
+ AM62X_IOPAD(0x0090, PIN_INPUT, 2) /* (M24) GPMC0_BE0N_CLE.MCASP1_ACLKX */
+ AM62X_IOPAD(0x0098, PIN_INPUT, 2) /* (U23) GPMC0_WAIT0.MCASP1_AFSX */
+ AM62X_IOPAD(0x008c, PIN_OUTPUT, 2) /* (L25) GPMC0_WEN.MCASP1_AXR0 */
+ AM62X_IOPAD(0x0084, PIN_INPUT, 2) /* (L23) GPMC0_ADVN_ALE.MCASP1_AXR2 */
+ >;
+ };
};
&wkup_uart0 {
@@ -352,6 +401,18 @@
pinctrl-names = "default";
pinctrl-0 = <&main_gpio1_ioexp_intr_pins_default>;
};
+
+ tlv320aic3106: audio-codec@1b {
+ #sound-dai-cells = <0>;
+ compatible = "ti,tlv320aic3106";
+ reg = <0x1b>;
+
+ /* Regulators */
+ AVDD-supply = <&vcc_3v3_sys>;
+ IOVDD-supply = <&vcc_3v3_sys>;
+ DRVDD-supply = <&vcc_3v3_sys>;
+ DVDD-supply = <&vcc_1v8>;
+ };
};
&main_i2c2 {
@@ -412,6 +473,34 @@
};
};
+&mcasp0 {
+ status = "disabled";
+};
+
+&mcasp1 {
+ status = "okay";
+ #sound-dai-cells = <0>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_mcasp1_pins_default>;
+
+ op-mode = <0>; /* MCASP_IIS_MODE */
+ tdm-slots = <2>;
+
+ serial-dir = < /* 0: INACTIVE, 1: TX, 2: RX */
+ 1 0 0 0
+ 0 0 0 0
+ 0 0 0 0
+ 0 0 0 0
+ >;
+ tx-num-evt = <32>;
+ rx-num-evt = <32>;
+};
+
+&mcasp2 {
+ status = "disabled";
+};
+
&mailbox0_cluster0 {
mbox_m4_0: mbox-m4-0 {
ti,mbox-rx = <0 0 0>;
--
2.17.1
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH v4 2/2] arm64: dts: ti: k3-am625-sk: Add audio output support
2022-06-20 10:27 [PATCH v4 0/2] arm64: ti: k3-am62: Enable audio output Jai Luthra
2022-06-20 10:27 ` [PATCH v4 1/2] arm64: dts: ti: k3-am62-main: Add McASP nodes Jai Luthra
2022-06-20 10:27 ` [PATCH v4 2/2] arm64: dts: ti: am625-sk: Add audio output support Jai Luthra
@ 2022-06-20 10:27 ` Jai Luthra
2022-07-06 23:31 ` Nishanth Menon
2 siblings, 1 reply; 6+ messages in thread
From: Jai Luthra @ 2022-06-20 10:27 UTC (permalink / raw)
To: Nishanth Menon, Vignesh Raghavendra, Rob Herring, Krzysztof Kozlowski
Cc: linux-kernel, linux-arm-kernel, devicetree, Jayesh Choudhary, Jai Luthra
Add nodes for audio codec and sound card, enable the audio serializer
(McASP1) under use and update pinmux. Disable all other McASP nodes.
Audio input is currently not working properly, so the RX port on McASP1
is disabled for now, until the issue is debugged.
The serializer is shared between HDMI and codec. By default codec is
used for output, but it can be toggled to HDMI using a FET switch
connected to the MCASP1_FET_SEL (J24) header on the board.
Signed-off-by: Jai Luthra <j-luthra@ti.com>
---
arch/arm64/boot/dts/ti/k3-am625-sk.dts | 89 ++++++++++++++++++++++++++
1 file changed, 89 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-am625-sk.dts b/arch/arm64/boot/dts/ti/k3-am625-sk.dts
index 39fb1d763037..a502b7ac48d4 100644
--- a/arch/arm64/boot/dts/ti/k3-am625-sk.dts
+++ b/arch/arm64/boot/dts/ti/k3-am625-sk.dts
@@ -121,6 +121,46 @@
<3300000 0x1>;
};
+ vcc_1v8: regulator-5 {
+ /* output of TPS6282518DMQ */
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vcc_3v3_sys>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ tlv320_mclk: clk-0 {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <12288000>;
+ };
+
+ sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,name = "AM62x-SKEVM";
+ simple-audio-card,widgets =
+ "Headphone", "Headphone Jack";
+ simple-audio-card,routing =
+ "Headphone Jack", "HPLOUT",
+ "Headphone Jack", "HPROUT";
+ simple-audio-card,format = "dsp_b";
+ simple-audio-card,bitclock-master = <&sound_master>;
+ simple-audio-card,frame-master = <&sound_master>;
+ simple-audio-card,bitclock-inversion;
+
+ simple-audio-card,cpu {
+ sound-dai = <&mcasp1>;
+ };
+
+ sound_master: simple-audio-card,codec {
+ sound-dai = <&tlv320aic3106>;
+ clocks = <&tlv320_mclk>;
+ };
+ };
+
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
@@ -266,6 +306,15 @@
AM62X_IOPAD(0x01d4, PIN_INPUT, 7) /* (B15) UART0_RTSn.GPIO1_23 */
>;
};
+
+ main_mcasp1_pins_default: main-mcasp1-pins-default {
+ pinctrl-single,pins = <
+ AM62X_IOPAD(0x0090, PIN_INPUT, 2) /* (M24) GPMC0_BE0N_CLE.MCASP1_ACLKX */
+ AM62X_IOPAD(0x0098, PIN_INPUT, 2) /* (U23) GPMC0_WAIT0.MCASP1_AFSX */
+ AM62X_IOPAD(0x008c, PIN_OUTPUT, 2) /* (L25) GPMC0_WEN.MCASP1_AXR0 */
+ AM62X_IOPAD(0x0084, PIN_INPUT, 2) /* (L23) GPMC0_ADVN_ALE.MCASP1_AXR2 */
+ >;
+ };
};
&wkup_uart0 {
@@ -352,6 +401,18 @@
pinctrl-names = "default";
pinctrl-0 = <&main_gpio1_ioexp_intr_pins_default>;
};
+
+ tlv320aic3106: audio-codec@1b {
+ #sound-dai-cells = <0>;
+ compatible = "ti,tlv320aic3106";
+ reg = <0x1b>;
+
+ /* Regulators */
+ AVDD-supply = <&vcc_3v3_sys>;
+ IOVDD-supply = <&vcc_3v3_sys>;
+ DRVDD-supply = <&vcc_3v3_sys>;
+ DVDD-supply = <&vcc_1v8>;
+ };
};
&main_i2c2 {
@@ -412,6 +473,34 @@
};
};
+&mcasp0 {
+ status = "disabled";
+};
+
+&mcasp1 {
+ status = "okay";
+ #sound-dai-cells = <0>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_mcasp1_pins_default>;
+
+ op-mode = <0>; /* MCASP_IIS_MODE */
+ tdm-slots = <2>;
+
+ serial-dir = < /* 0: INACTIVE, 1: TX, 2: RX */
+ 1 0 0 0
+ 0 0 0 0
+ 0 0 0 0
+ 0 0 0 0
+ >;
+ tx-num-evt = <32>;
+ rx-num-evt = <32>;
+};
+
+&mcasp2 {
+ status = "disabled";
+};
+
&mailbox0_cluster0 {
mbox_m4_0: mbox-m4-0 {
ti,mbox-rx = <0 0 0>;
--
2.17.1
^ permalink raw reply related [flat|nested] 6+ messages in thread
* Re: [PATCH v4 2/2] arm64: dts: ti: am625-sk: Add audio output support
2022-06-20 10:27 ` [PATCH v4 2/2] arm64: dts: ti: am625-sk: Add audio output support Jai Luthra
@ 2022-06-20 10:35 ` Jai Luthra
0 siblings, 0 replies; 6+ messages in thread
From: Jai Luthra @ 2022-06-20 10:35 UTC (permalink / raw)
To: Nishanth Menon, Vignesh Raghavendra, Rob Herring, Krzysztof Kozlowski
Cc: linux-kernel, linux-arm-kernel, devicetree, Jayesh Choudhary, Jai Luthra
On 15:57-20220620, Jai Luthra wrote:
> Add nodes for audio codec and sound card, enable the audio serializer
> (McASP1) under use and update pinmux. Disable all other McASP nodes.
>
> Audio input is currently not working properly, so the RX port on McASP1
> is disabled for now, until the issue is debugged.
>
> The serializer is shared between HDMI and codec. By default codec is
> used for output, but it can be toggled to HDMI using a FET switch
> connected to the MCASP1_FET_SEL (J24) header on the board.
>
> Signed-off-by: Jai Luthra <j-luthra@ti.com>
> ---
> arch/arm64/boot/dts/ti/k3-am625-sk.dts | 89 ++++++++++++++++++++++++++
> 1 file changed, 89 insertions(+)
Oops, I sent this patch twice in the series. Please ignore this one.
Thanks,
Jai
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH v4 2/2] arm64: dts: ti: k3-am625-sk: Add audio output support
2022-06-20 10:27 ` [PATCH v4 2/2] arm64: dts: ti: k3-am625-sk: " Jai Luthra
@ 2022-07-06 23:31 ` Nishanth Menon
0 siblings, 0 replies; 6+ messages in thread
From: Nishanth Menon @ 2022-07-06 23:31 UTC (permalink / raw)
To: Jai Luthra
Cc: Vignesh Raghavendra, Rob Herring, Krzysztof Kozlowski,
linux-kernel, linux-arm-kernel, devicetree, Jayesh Choudhary
On 15:57-20220620, Jai Luthra wrote:
> Add nodes for audio codec and sound card, enable the audio serializer
> (McASP1) under use and update pinmux. Disable all other McASP nodes.
>
> Audio input is currently not working properly, so the RX port on McASP1
> is disabled for now, until the issue is debugged.
>
> The serializer is shared between HDMI and codec. By default codec is
> used for output, but it can be toggled to HDMI using a FET switch
> connected to the MCASP1_FET_SEL (J24) header on the board.
>
> Signed-off-by: Jai Luthra <j-luthra@ti.com>
[...]
> + main_mcasp1_pins_default: main-mcasp1-pins-default {
> + pinctrl-single,pins = <
> + AM62X_IOPAD(0x0090, PIN_INPUT, 2) /* (M24) GPMC0_BE0N_CLE.MCASP1_ACLKX */
> + AM62X_IOPAD(0x0098, PIN_INPUT, 2) /* (U23) GPMC0_WAIT0.MCASP1_AFSX */
> + AM62X_IOPAD(0x008c, PIN_OUTPUT, 2) /* (L25) GPMC0_WEN.MCASP1_AXR0 */
> + AM62X_IOPAD(0x0084, PIN_INPUT, 2) /* (L23) GPMC0_ADVN_ALE.MCASP1_AXR2 */
> + >;
> + };
> };
>
> &wkup_uart0 {
> @@ -352,6 +401,18 @@
> pinctrl-names = "default";
> pinctrl-0 = <&main_gpio1_ioexp_intr_pins_default>;
> };
> +
> + tlv320aic3106: audio-codec@1b {
> + #sound-dai-cells = <0>;
> + compatible = "ti,tlv320aic3106";
I cant pick up a patch with compatibles that are'nt converted to yaml.
Please convert to yaml in master and then post.
> + reg = <0x1b>;
> +
> + /* Regulators */
> + AVDD-supply = <&vcc_3v3_sys>;
> + IOVDD-supply = <&vcc_3v3_sys>;
> + DRVDD-supply = <&vcc_3v3_sys>;
> + DVDD-supply = <&vcc_1v8>;
> + };
> };
>
> &main_i2c2 {
> @@ -412,6 +473,34 @@
> };
> };
>
> +&mcasp0 {
> + status = "disabled";
> +};
> +
> +&mcasp1 {
> + status = "okay";
we don't need to set okay on a node that is ok by default.
> + #sound-dai-cells = <0>;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&main_mcasp1_pins_default>;
> +
> + op-mode = <0>; /* MCASP_IIS_MODE */
> + tdm-slots = <2>;
> +
> + serial-dir = < /* 0: INACTIVE, 1: TX, 2: RX */
> + 1 0 0 0
> + 0 0 0 0
> + 0 0 0 0
> + 0 0 0 0
> + >;
> + tx-num-evt = <32>;
> + rx-num-evt = <32>;
> +};
> +
> +&mcasp2 {
> + status = "disabled";
> +};
> +
> &mailbox0_cluster0 {
> mbox_m4_0: mbox-m4-0 {
> ti,mbox-rx = <0 0 0>;
>
> --
> 2.17.1
>
--
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2022-07-06 23:31 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2022-06-20 10:27 [PATCH v4 0/2] arm64: ti: k3-am62: Enable audio output Jai Luthra
2022-06-20 10:27 ` [PATCH v4 1/2] arm64: dts: ti: k3-am62-main: Add McASP nodes Jai Luthra
2022-06-20 10:27 ` [PATCH v4 2/2] arm64: dts: ti: am625-sk: Add audio output support Jai Luthra
2022-06-20 10:35 ` Jai Luthra
2022-06-20 10:27 ` [PATCH v4 2/2] arm64: dts: ti: k3-am625-sk: " Jai Luthra
2022-07-06 23:31 ` Nishanth Menon
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).