[PATCH v6 0/5] Add SPI Driver to HPE GXP Architecture

[PATCH v6 0/5] Add SPI Driver to HPE GXP Architecture

[nick.hawkins]

From: Nick Hawkins <nick.hawkins@hpe.com>

Changes since v6:
 *Removed spaces between tags on commit descriptions

Changes since v5:
 *Fixed indentation in Kconfig file

Changes since v4:
 *Removed unnecessary quotes in hpe,gxp-spifi.yaml

Changes since v3:
 *Fixed indentations in hpe,gxp-spifi.yaml

Changes since v2:
 *Changed the CONFIG_SPI_GXP from y to m in defconfig
 *Removed extra space around < > for reg in hpe,gxp-spifi.yaml
 *Changed interrupt-parrent to interrupt-parent in hpe,gxp-spifi.yaml
 *Removed repeated include file in spi-gxp.c
 *Removed unnecessary initialization of ret variable in spi-gxp.c
 *Removed conditional variable checks where failure is not possible in
  spi-gxp.c
 *Removed unnecessary variable cs in spi-gxp.c
 *Removed blank gxp-spifi-remove function in spi-gxp.c
 *Fixed error messages so they are not repetitive

The GXP supports 3 separate SPI interfaces to accommodate the system
flash, core flash, and other functions. The SPI engine supports variable
clock frequency, selectable 3-byte or 4-byte addressing and a
configurable x1, x2, and x4 command/address/data modes. The memory
buffer for reading and writing ranges between 256 bytes and 8KB. This
driver supports access to the core flash and bios part.

Nick Hawkins (5):
  spi: spi-gxp: Add support for HPE GXP SoCs
  spi: dt-bindings: add documentation for hpe,gxp-spifi
  ARM: dts: hpe: Add spi driver node
  ARM: configs: multi_v7_defconfig: Enable HPE GXP SPI driver
  MAINTAINERS: add spi support to GXP

 .../bindings/spi/hpe,gxp-spifi.yaml           |  56 +++
 MAINTAINERS                                   |   2 +
 arch/arm/boot/dts/hpe-bmc-dl360gen10.dts      |  58 ++++
 arch/arm/boot/dts/hpe-gxp.dtsi                |  21 +-
 arch/arm/configs/multi_v7_defconfig           |   1 +
 drivers/spi/Kconfig                           |   7 +
 drivers/spi/Makefile                          |   1 +
 drivers/spi/spi-gxp.c                         | 325 ++++++++++++++++++
 8 files changed, 470 insertions(+), 1 deletion(-)
 create mode 100644 Documentation/devicetree/bindings/spi/hpe,gxp-spifi.yaml
 create mode 100644 drivers/spi/spi-gxp.c

-- 
2.17.1

[PATCH v6 1/5] spi: spi-gxp: Add support for HPE GXP SoCs

[nick.hawkins]

From: Nick Hawkins <nick.hawkins@hpe.com>

The GXP supports 3 separate SPI interfaces to accommodate the system
flash, core flash, and other functions. The SPI engine supports variable
clock frequency, selectable 3-byte or 4-byte addressing and a
configurable x1, x2, and x4 command/address/data modes. The memory
buffer for reading and writing ranges between 256 bytes and 8KB. This
driver supports access to the core flash and bios part.

Signed-off-by: Nick Hawkins <nick.hawkins@hpe.com>

---
v6:
 *No change
v5:
 *Add missing spaces in Kconfig to have proper alignment
v4:
 *No change
v3:
 *No change
v2:
 *Removed repeated include file
 *Removed unnecessary initialization of ret variable
 *Removed conditional variable checks where failure is impossible
 *Removed unecessary variable cs and instead used in the initialization
 *Removed blank gxp_spifi_remove function
 *Fixed error messages so they are not repetitive
---
 drivers/spi/Kconfig   |   7 +
 drivers/spi/Makefile  |   1 +
 drivers/spi/spi-gxp.c | 325 ++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 333 insertions(+)
 create mode 100644 drivers/spi/spi-gxp.c

diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index 3b1044ebc400..e3787cd9b475 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -371,6 +371,13 @@ config SPI_FSL_QUADSPI
 	  This controller does not support generic SPI messages. It only
 	  supports the high-level SPI memory interface.
 
+config SPI_GXP
+	tristate "GXP SPI driver"
+	depends on ARCH_HPE || COMPILE_TEST
+	help
+	  This enables support for the driver for GXP bus attached SPI
+	  controllers.
+
 config SPI_HISI_KUNPENG
 	tristate "HiSilicon SPI Controller for Kunpeng SoCs"
 	depends on (ARM64 && ACPI) || COMPILE_TEST
diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
index 0f44eb6083a5..ca5f204017ee 100644
--- a/drivers/spi/Makefile
+++ b/drivers/spi/Makefile
@@ -57,6 +57,7 @@ obj-$(CONFIG_SPI_FSL_LPSPI)		+= spi-fsl-lpspi.o
 obj-$(CONFIG_SPI_FSL_QUADSPI)		+= spi-fsl-qspi.o
 obj-$(CONFIG_SPI_FSL_SPI)		+= spi-fsl-spi.o
 obj-$(CONFIG_SPI_GPIO)			+= spi-gpio.o
+obj-$(CONFIG_SPI_GXP)			+= spi-gxp.o
 obj-$(CONFIG_SPI_HISI_KUNPENG)		+= spi-hisi-kunpeng.o
 obj-$(CONFIG_SPI_HISI_SFC_V3XX)		+= spi-hisi-sfc-v3xx.o
 obj-$(CONFIG_SPI_IMG_SPFI)		+= spi-img-spfi.o
diff --git a/drivers/spi/spi-gxp.c b/drivers/spi/spi-gxp.c
new file mode 100644
index 000000000000..9ea355f7d64f
--- /dev/null
+++ b/drivers/spi/spi-gxp.c
@@ -0,0 +1,325 @@
+// SPDX-License-Identifier: GPL-2.0=or-later
+/* Copyright (C) 2022 Hewlett-Packard Development Company, L.P. */
+
+#include <linux/iopoll.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/spi-mem.h>
+
+#define GXP_SPI0_MAX_CHIPSELECT	2
+#define GXP_SPI_SLEEP_TIME	1
+#define GXP_SPI_TIMEOUT (130 * 1000000 / GXP_SPI_SLEEP_TIME)
+
+#define MANUAL_MODE		0
+#define DIRECT_MODE		1
+#define SPILDAT_LEN		256
+
+#define OFFSET_SPIMCFG		0x0
+#define OFFSET_SPIMCTRL		0x4
+#define OFFSET_SPICMD		0x5
+#define OFFSET_SPIDCNT		0x6
+#define OFFSET_SPIADDR		0x8
+#define OFFSET_SPIINTSTS	0xc
+
+#define SPIMCTRL_START		0x01
+#define SPIMCTRL_BUSY		0x02
+#define SPIMCTRL_DIR		0x08
+
+struct gxp_spi;
+
+struct gxp_spi_chip {
+	struct gxp_spi *spifi;
+	u32 cs;
+};
+
+struct gxp_spi_data {
+	u32 max_cs;
+	u32 mode_bits;
+};
+
+struct gxp_spi {
+	const struct gxp_spi_data *data;
+	void __iomem *reg_base;
+	void __iomem *dat_base;
+	void __iomem *dir_base;
+	struct device *dev;
+	struct gxp_spi_chip chips[GXP_SPI0_MAX_CHIPSELECT];
+};
+
+static void gxp_spi_set_mode(struct gxp_spi *spifi, int mode)
+{
+	u8 value;
+	void __iomem *reg_base = spifi->reg_base;
+
+	value = readb(reg_base + OFFSET_SPIMCTRL);
+
+	if (mode == MANUAL_MODE) {
+		writeb(0x55, reg_base + OFFSET_SPICMD);
+		writeb(0xaa, reg_base + OFFSET_SPICMD);
+		value &= ~0x30;
+	} else {
+		value |= 0x30;
+	}
+	writeb(value, reg_base + OFFSET_SPIMCTRL);
+}
+
+static int gxp_spi_read_reg(struct gxp_spi_chip *chip, const struct spi_mem_op *op)
+{
+	int ret;
+	struct gxp_spi *spifi = chip->spifi;
+	void __iomem *reg_base = spifi->reg_base;
+	u32 value;
+
+	value = readl(reg_base + OFFSET_SPIMCFG);
+	value &= ~(1 << 24);
+	value |= (chip->cs << 24);
+	value &= ~(0x07 << 16);
+	value &= ~(0x1f << 19);
+	writel(value, reg_base + OFFSET_SPIMCFG);
+
+	writel(0, reg_base + OFFSET_SPIADDR);
+
+	writeb(op->cmd.opcode, reg_base + OFFSET_SPICMD);
+
+	writew(op->data.nbytes, reg_base + OFFSET_SPIDCNT);
+
+	value = readb(reg_base + OFFSET_SPIMCTRL);
+	value &= ~SPIMCTRL_DIR;
+	value |= SPIMCTRL_START;
+
+	writeb(value, reg_base + OFFSET_SPIMCTRL);
+
+	ret = readb_poll_timeout(reg_base + OFFSET_SPIMCTRL, value,
+				 !(value & SPIMCTRL_BUSY),
+				 GXP_SPI_SLEEP_TIME, GXP_SPI_TIMEOUT);
+	if (ret) {
+		dev_warn(spifi->dev, "read reg busy time out\n");
+		return ret;
+	}
+
+	memcpy_fromio(op->data.buf.in, spifi->dat_base, op->data.nbytes);
+	return ret;
+}
+
+static int gxp_spi_write_reg(struct gxp_spi_chip *chip, const struct spi_mem_op *op)
+{
+	int ret;
+	struct gxp_spi *spifi = chip->spifi;
+	void __iomem *reg_base = spifi->reg_base;
+	u32 value;
+
+	value = readl(reg_base + OFFSET_SPIMCFG);
+	value &= ~(1 << 24);
+	value |= (chip->cs << 24);
+	value &= ~(0x07 << 16);
+	value &= ~(0x1f << 19);
+	writel(value, reg_base + OFFSET_SPIMCFG);
+
+	writel(0, reg_base + OFFSET_SPIADDR);
+
+	writeb(op->cmd.opcode, reg_base + OFFSET_SPICMD);
+
+	memcpy_toio(spifi->dat_base, op->data.buf.in, op->data.nbytes);
+
+	writew(op->data.nbytes, reg_base + OFFSET_SPIDCNT);
+
+	value = readb(reg_base + OFFSET_SPIMCTRL);
+	value |= SPIMCTRL_DIR;
+	value |= SPIMCTRL_START;
+
+	writeb(value, reg_base + OFFSET_SPIMCTRL);
+
+	ret = readb_poll_timeout(reg_base + OFFSET_SPIMCTRL, value,
+				 !(value & SPIMCTRL_BUSY),
+				 GXP_SPI_SLEEP_TIME, GXP_SPI_TIMEOUT);
+	if (ret)
+		dev_warn(spifi->dev, "write reg busy time out\n");
+
+	return ret;
+}
+
+static ssize_t gxp_spi_read(struct gxp_spi_chip *chip, const struct spi_mem_op *op)
+{
+	struct gxp_spi *spifi = chip->spifi;
+	u32 offset = op->addr.val;
+
+	if (chip->cs == 0)
+		offset += 0x4000000;
+
+	memcpy_fromio(op->data.buf.in, spifi->dir_base + offset, op->data.nbytes);
+
+	return 0;
+}
+
+static ssize_t gxp_spi_write(struct gxp_spi_chip *chip, const struct spi_mem_op *op)
+{
+	struct gxp_spi *spifi = chip->spifi;
+	void __iomem *reg_base = spifi->reg_base;
+	u32 write_len;
+	u32 value;
+	int ret;
+
+	write_len = op->data.nbytes;
+	if (write_len > SPILDAT_LEN)
+		write_len = SPILDAT_LEN;
+
+	value = readl(reg_base + OFFSET_SPIMCFG);
+	value &= ~(1 << 24);
+	value |= (chip->cs << 24);
+	value &= ~(0x07 << 16);
+	value |= (op->addr.nbytes << 16);
+	value &= ~(0x1f << 19);
+	writel(value, reg_base + OFFSET_SPIMCFG);
+
+	writel(op->addr.val, reg_base + OFFSET_SPIADDR);
+
+	writeb(op->cmd.opcode, reg_base + OFFSET_SPICMD);
+
+	writew(write_len, reg_base + OFFSET_SPIDCNT);
+
+	memcpy_toio(spifi->dat_base, op->data.buf.in, write_len);
+
+	value = readb(reg_base + OFFSET_SPIMCTRL);
+	value |= SPIMCTRL_DIR;
+	value |= SPIMCTRL_START;
+
+	writeb(value, reg_base + OFFSET_SPIMCTRL);
+
+	ret = readb_poll_timeout(reg_base + OFFSET_SPIMCTRL, value,
+				 !(value & SPIMCTRL_BUSY),
+				 GXP_SPI_SLEEP_TIME, GXP_SPI_TIMEOUT);
+	if (ret) {
+		dev_warn(spifi->dev, "write busy time out\n");
+		return ret;
+	}
+
+	return write_len;
+}
+
+static int do_gxp_exec_mem_op(struct spi_mem *mem, const struct spi_mem_op *op)
+{
+	struct gxp_spi *spifi = spi_controller_get_devdata(mem->spi->master);
+	struct gxp_spi_chip *chip = &spifi->chips[mem->spi->chip_select];
+	int ret;
+
+	if (op->data.dir == SPI_MEM_DATA_IN) {
+		if (!op->addr.nbytes)
+			ret = gxp_spi_read_reg(chip, op);
+		else
+			ret = gxp_spi_read(chip, op);
+	} else {
+		if (!op->addr.nbytes)
+			ret = gxp_spi_write_reg(chip, op);
+		else
+			ret = gxp_spi_write(chip, op);
+	}
+
+	return ret;
+}
+
+static int gxp_exec_mem_op(struct spi_mem *mem, const struct spi_mem_op *op)
+{
+	int ret;
+
+	ret = do_gxp_exec_mem_op(mem, op);
+	if (ret)
+		dev_err(&mem->spi->dev, "operation failed: %d", ret);
+
+	return ret;
+}
+
+static const struct spi_controller_mem_ops gxp_spi_mem_ops = {
+	.exec_op = gxp_exec_mem_op,
+};
+
+static int gxp_spi_setup(struct spi_device *spi)
+{
+	struct gxp_spi *spifi = spi_controller_get_devdata(spi->master);
+	unsigned int cs = spi->chip_select;
+	struct gxp_spi_chip *chip = &spifi->chips[cs];
+
+	chip->spifi = spifi;
+	chip->cs = cs;
+
+	gxp_spi_set_mode(spifi, MANUAL_MODE);
+
+	return 0;
+}
+
+static int gxp_spifi_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	const struct gxp_spi_data *data;
+	struct spi_controller *ctlr;
+	struct gxp_spi *spifi;
+	struct resource *res;
+	int ret;
+
+	data = of_device_get_match_data(&pdev->dev);
+
+	ctlr = devm_spi_alloc_master(dev, sizeof(*spifi));
+	if (!ctlr)
+		return -ENOMEM;
+
+	spifi = spi_controller_get_devdata(ctlr);
+
+	platform_set_drvdata(pdev, spifi);
+	spifi->data = data;
+	spifi->dev = dev;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	spifi->reg_base = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(spifi->reg_base))
+		return PTR_ERR(spifi->reg_base);
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+	spifi->dat_base = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(spifi->dat_base))
+		return PTR_ERR(spifi->dat_base);
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 2);
+	spifi->dir_base = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(spifi->dir_base))
+		return PTR_ERR(spifi->dir_base);
+
+	ctlr->mode_bits = data->mode_bits;
+	ctlr->bus_num = pdev->id;
+	ctlr->mem_ops = &gxp_spi_mem_ops;
+	ctlr->setup = gxp_spi_setup;
+	ctlr->num_chipselect = data->max_cs;
+	ctlr->dev.of_node = dev->of_node;
+
+	ret = devm_spi_register_controller(dev, ctlr);
+	if (ret) {
+		return dev_err_probe(&pdev->dev, ret,
+				     "failed to register spi controller\n");
+	}
+
+	return 0;
+}
+
+static const struct gxp_spi_data gxp_spifi_data = {
+	.max_cs	= 2,
+	.mode_bits = 0,
+};
+
+static const struct of_device_id gxp_spifi_match[] = {
+	{.compatible = "hpe,gxp-spifi", .data = &gxp_spifi_data },
+	{ /* null */ }
+};
+MODULE_DEVICE_TABLE(of, gxp_spifi_match);
+
+static struct platform_driver gxp_spifi_driver = {
+	.probe = gxp_spifi_probe,
+	.driver = {
+		.name = "gxp-spifi",
+		.of_match_table = gxp_spifi_match,
+	},
+};
+module_platform_driver(gxp_spifi_driver);
+
+MODULE_DESCRIPTION("HPE GXP SPI Flash Interface driver");
+MODULE_AUTHOR("Nick Hawkins <nick.hawkins@hpe.com>");
+MODULE_LICENSE("GPL");
-- 
2.17.1

[PATCH v6 2/5] spi: dt-bindings: add documentation for hpe,gxp-spifi

[nick.hawkins]

From: Nick Hawkins <nick.hawkins@hpe.com>

Create documentation for the hpe,gxp-spifi binding to support access to
the SPI parts

Signed-off-by: Nick Hawkins <nick.hawkins@hpe.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

---
v6:
 *Remove blank line between tags in commit description
v5:
 *No change, add Krzysztof review from previous version
v4:
 *Remove uneccessary quotes
v3:
 *Fix indentation
v2:
 *Removed extra space around < > for reg
 *Changed interrupt-parrent to interrupt-parent
---
 .../bindings/spi/hpe,gxp-spifi.yaml           | 56 +++++++++++++++++++
 1 file changed, 56 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/spi/hpe,gxp-spifi.yaml

diff --git a/Documentation/devicetree/bindings/spi/hpe,gxp-spifi.yaml b/Documentation/devicetree/bindings/spi/hpe,gxp-spifi.yaml
new file mode 100644
index 000000000000..7797c3123b7e
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/hpe,gxp-spifi.yaml
@@ -0,0 +1,56 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/spi/hpe,gxp-spifi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: HPE GXP spi controller flash interface
+
+maintainers:
+  - Nick Hawkins <nick.hawkins@hpe.com>
+  - Jean-Marie Verdun <verdun@hpe.com>
+
+allOf:
+  - $ref: spi-controller.yaml#
+
+properties:
+  compatible:
+    const: hpe,gxp-spifi
+
+  reg:
+    items:
+      - description: cfg registers
+      - description: data registers
+      - description: mapped memory
+
+  interrupts:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+  - interrupts
+
+unevaluatedProperties: false
+
+examples:
+  - |
+
+    spi@200 {
+      compatible = "hpe,gxp-spifi";
+      reg = <0x200 0x80>, <0xc000 0x100>, <0x38000000 0x800000>;
+      interrupts = <20>;
+      interrupt-parent = <&vic0>;
+      #address-cells = <1>;
+      #size-cells = <0>;
+
+      flash@0 {
+        reg = <0>;
+        compatible = "jedec,spi-nor";
+      };
+
+      flash@1 {
+        reg = <1>;
+        compatible = "jedec,spi-nor";
+      };
+    };
-- 
2.17.1

[PATCH v6 3/5] ARM: dts: hpe: Add spi driver node

[nick.hawkins]

From: Nick Hawkins <nick.hawkins@hpe.com>

Add support for the SPI flash interface on the GXP SoC.

Signed-off-by: Nick Hawkins <nick.hawkins@hpe.com>

---
v6:
 *No change
v5:
 *No change
v4:
 *No change
v3:
 *No change
v2:
 *No change
---
 arch/arm/boot/dts/hpe-bmc-dl360gen10.dts | 58 ++++++++++++++++++++++++
 arch/arm/boot/dts/hpe-gxp.dtsi           | 21 ++++++++-
 2 files changed, 78 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/hpe-bmc-dl360gen10.dts b/arch/arm/boot/dts/hpe-bmc-dl360gen10.dts
index 3a7382ce40ef..d49dcef95c5c 100644
--- a/arch/arm/boot/dts/hpe-bmc-dl360gen10.dts
+++ b/arch/arm/boot/dts/hpe-bmc-dl360gen10.dts
@@ -24,3 +24,61 @@
 		reg = <0x40000000 0x20000000>;
 	};
 };
+
+&spifi {
+	status = "okay";
+	flash@0 {
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			u-boot@0 {
+				label = "u-boot";
+				reg = <0x0 0x60000>;
+			};
+
+			u-boot-env@60000 {
+				label = "u-boot-env";
+				reg = <0x60000 0x20000>;
+			};
+
+			kernel@80000 {
+				label = "kernel";
+				reg = <0x80000 0x4c0000>;
+			};
+
+			rofs@540000 {
+				label = "rofs";
+				reg = <0x540000 0x1740000>;
+			};
+
+			rwfs@1c80000 {
+				label = "rwfs";
+				reg = <0x1c80000 0x250000>;
+			};
+
+			section@1ed0000{
+				label = "section";
+				reg = <0x1ed0000 0x130000>;
+			};
+		};
+	};
+	flash@1 {
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			host-prime@0 {
+				label = "host-prime";
+				reg = <0x0 0x02000000>;
+			};
+
+			host-second@2000000 {
+				label = "host-second";
+				reg = <0x02000000 0x02000000>;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/hpe-gxp.dtsi b/arch/arm/boot/dts/hpe-gxp.dtsi
index cf735b3c4f35..f28349bdeee1 100644
--- a/arch/arm/boot/dts/hpe-gxp.dtsi
+++ b/arch/arm/boot/dts/hpe-gxp.dtsi
@@ -56,9 +56,28 @@
 			compatible = "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
-			ranges = <0x0 0xc0000000 0x30000000>;
+			ranges = <0x0 0xc0000000 0x40000000>;
 			dma-ranges;
 
+			spifi: spi@200 {
+				compatible = "hpe,gxp-spifi";
+				reg = <0x200 0x80>, <0xc000 0x100>, <0x38000000 0x8000000>;
+				interrupts = <20>;
+				interrupt-parent = <&vic0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+				flash@0 {
+					reg = <0>;
+					compatible = "jedec,spi-nor";
+				};
+
+				flash@1 {
+					reg = <1>;
+					compatible = "jedec,spi-nor";
+				};
+			};
+
 			vic0: interrupt-controller@eff0000 {
 				compatible = "arm,pl192-vic";
 				reg = <0xeff0000 0x1000>;
-- 
2.17.1

[PATCH v6 4/5] ARM: configs: multi_v7_defconfig: Enable HPE GXP SPI driver

[nick.hawkins]

From: Nick Hawkins <nick.hawkins@hpe.com>

Enable the SPI driver on the HPE GXP BMC.

Signed-off-by: Nick Hawkins <nick.hawkins@hpe.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

---
v6:
 *Remove blank line between tags on commit description
v5:
 *No change, add Acked-by from Krzsztof from previous version
v4:
 *No change
v3:
 *No change
v2:
 *Change CONFIG_SPI_GXP from y to m
---
 arch/arm/configs/multi_v7_defconfig | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm/configs/multi_v7_defconfig b/arch/arm/configs/multi_v7_defconfig
index ce9826bce29b..ee8a730dabc9 100644
--- a/arch/arm/configs/multi_v7_defconfig
+++ b/arch/arm/configs/multi_v7_defconfig
@@ -443,6 +443,7 @@ CONFIG_SPI_CADENCE=y
 CONFIG_SPI_DAVINCI=y
 CONFIG_SPI_FSL_QUADSPI=m
 CONFIG_SPI_GPIO=m
+CONFIG_SPI_GXP=m
 CONFIG_SPI_FSL_DSPI=m
 CONFIG_SPI_OMAP24XX=y
 CONFIG_SPI_ORION=y
-- 
2.17.1

[PATCH v6 5/5] MAINTAINERS: add spi support to GXP

[nick.hawkins]

From: Nick Hawkins <nick.hawkins@hpe.com>

Add the spi driver and dt-binding documentation

Signed-off-by: Nick Hawkins <nick.hawkins@hpe.com>

---
v6:
 *No change
v5:
 *No change
v4:
 *No change
v3:
 *No change
v2:
 *No change
---
 MAINTAINERS | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/MAINTAINERS b/MAINTAINERS
index a6d3bd9d2a8d..f87728549ecf 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -2140,11 +2140,13 @@ M:	Jean-Marie Verdun <verdun@hpe.com>
 M:	Nick Hawkins <nick.hawkins@hpe.com>
 S:	Maintained
 F:	Documentation/devicetree/bindings/arm/hpe,gxp.yaml
+F:	Documentation/devicetree/bindings/spi/hpe,gxp-spi.yaml
 F:	Documentation/devicetree/bindings/timer/hpe,gxp-timer.yaml
 F:	arch/arm/boot/dts/hpe-bmc*
 F:	arch/arm/boot/dts/hpe-gxp*
 F:	arch/arm/mach-hpe/
 F:	drivers/clocksource/timer-gxp.c
+F:	drivers/spi/spi-gxp.c
 F:	drivers/watchdog/gxp-wdt.c
 
 ARM/IGEP MACHINE SUPPORT
-- 
2.17.1

Re: (subset) [PATCH v6 0/5] Add SPI Driver to HPE GXP Architecture

[Mark Brown]

On Thu, 28 Jul 2022 11:14:54 -0500, nick.hawkins@hpe.com wrote:
> From: Nick Hawkins <nick.hawkins@hpe.com>
> 
> Changes since v6:
>  *Removed spaces between tags on commit descriptions
> 
> Changes since v5:
>  *Fixed indentation in Kconfig file
> 
> [...]

Applied to

   https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi.git for-next

Thanks!

[1/5] spi: spi-gxp: Add support for HPE GXP SoCs
      commit: 730bc8ba5e9ec103065142975015a793558f09a0
[2/5] spi: dt-bindings: add documentation for hpe,gxp-spifi
      commit: 8cc35b86546dc35fb4f5ff7d1d163c5efc78bf0e
[5/5] MAINTAINERS: add spi support to GXP
      commit: a1848b0fa2517a8d0bbc2783c90aefd4b7e7567a

All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.

You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying
to this mail.

Thanks,
Mark

RE: [PATCH v6 3/5] ARM: dts: hpe: Add spi driver node

[Hawkins, Nick]

Greetings all,

Was there a particular issue with this patch? I just realized that patches 1,2, and 5 were accepted but not 3 or 4.

Thanks,

-Nick Hawkins

Re: [PATCH v6 3/5] ARM: dts: hpe: Add spi driver node

[Arnd Bergmann]

On Wed, Oct 5, 2022, at 10:33 PM, Hawkins, Nick wrote:
>
> Was there a particular issue with this patch? I just realized that 
> patches 1,2, and 5 were accepted but not 3 or 4.

It looks like you sent the patch to a lot of people, without addressing
anyone in particular. I certainly did not expect to pick it up like this.

When you resend the missing patches after 6.1-rc1, please send the
ones you want to be merged through the soc tree to:soc@kernel.org,
with reviewers and mailing lists on Cc, but nobody else as the
recipient.

For the SoC tree, I usually have separate branches for code
changes (usually just Kconfig and MAINTAINERS entries in case of
arm64), devicetree changes, defconfig changes and driver (typically
drivers/soc, but could be others that have no separate subsystem
maintainers), so ideally you send a set of patches or a pull request
for each such topic branch.

      Arnd