* [PATCH] drm/bridge: anx7625: Set HPD irq detect window to 2ms
@ 2022-09-03 13:08 Xin Ji
2022-09-05 16:48 ` Robert Foss
0 siblings, 1 reply; 4+ messages in thread
From: Xin Ji @ 2022-09-03 13:08 UTC (permalink / raw)
To: Andrzej Hajda, Neil Armstrong, Robert Foss, Laurent Pinchart,
Jonas Karlman, Jernej Skrabec, David Airlie, Daniel Vetter
Cc: bliang, qwen, mliu, hsinyi, Xin Ji, dri-devel, linux-kernel
Some panels trigger HPD irq due to noise, the HPD debounce
may be 1.8ms, exceeding the default irq detect window, ~1.4ms.
This patch set HPD irq detection window to 2ms to
tolerate the HPD noise.
Signed-off-by: Xin Ji <xji@analogixsemi.com>
---
drivers/gpu/drm/bridge/analogix/anx7625.c | 14 ++++++++++++++
drivers/gpu/drm/bridge/analogix/anx7625.h | 6 ++++++
2 files changed, 20 insertions(+)
diff --git a/drivers/gpu/drm/bridge/analogix/anx7625.c b/drivers/gpu/drm/bridge/analogix/anx7625.c
index c74b5df4cade..0c323b5a1c99 100644
--- a/drivers/gpu/drm/bridge/analogix/anx7625.c
+++ b/drivers/gpu/drm/bridge/analogix/anx7625.c
@@ -1440,6 +1440,20 @@ static void anx7625_start_dp_work(struct anx7625_data *ctx)
static int anx7625_read_hpd_status_p0(struct anx7625_data *ctx)
{
+ int ret;
+
+ /* Set irq detect window to 2ms */
+ ret = anx7625_reg_write(ctx, ctx->i2c.tx_p2_client,
+ HPD_DET_TIMER_BIT0_7, HPD_TIME & 0xFF);
+ ret |= anx7625_reg_write(ctx, ctx->i2c.tx_p2_client,
+ HPD_DET_TIMER_BIT8_15,
+ (HPD_TIME >> 8) & 0xFF);
+ ret |= anx7625_reg_write(ctx, ctx->i2c.tx_p2_client,
+ HPD_DET_TIMER_BIT16_23,
+ (HPD_TIME >> 16) & 0xFF);
+ if (ret < 0)
+ return ret;
+
return anx7625_reg_read(ctx, ctx->i2c.rx_p0_client, SYSTEM_STSTUS);
}
diff --git a/drivers/gpu/drm/bridge/analogix/anx7625.h b/drivers/gpu/drm/bridge/analogix/anx7625.h
index e257a84db962..14f33d6be289 100644
--- a/drivers/gpu/drm/bridge/analogix/anx7625.h
+++ b/drivers/gpu/drm/bridge/analogix/anx7625.h
@@ -132,6 +132,12 @@
#define I2S_SLAVE_MODE 0x08
#define AUDIO_LAYOUT 0x01
+#define HPD_DET_TIMER_BIT0_7 0xea
+#define HPD_DET_TIMER_BIT8_15 0xeb
+#define HPD_DET_TIMER_BIT16_23 0xec
+/* HPD debounce time 2ms for 27M clock */
+#define HPD_TIME 54000
+
#define AUDIO_CONTROL_REGISTER 0xe6
#define TDM_TIMING_MODE 0x08
--
2.25.1
^ permalink raw reply related [flat|nested] 4+ messages in thread
* Re: [PATCH] drm/bridge: anx7625: Set HPD irq detect window to 2ms
2022-09-03 13:08 [PATCH] drm/bridge: anx7625: Set HPD irq detect window to 2ms Xin Ji
@ 2022-09-05 16:48 ` Robert Foss
2022-09-06 2:57 ` Xin Ji
0 siblings, 1 reply; 4+ messages in thread
From: Robert Foss @ 2022-09-05 16:48 UTC (permalink / raw)
To: Xin Ji
Cc: Andrzej Hajda, Neil Armstrong, Laurent Pinchart, Jonas Karlman,
Jernej Skrabec, David Airlie, Daniel Vetter, bliang, qwen, mliu,
hsinyi, dri-devel, linux-kernel
Hi Xin,
On Sat, 3 Sept 2022 at 15:09, Xin Ji <xji@analogixsemi.com> wrote:
>
> Some panels trigger HPD irq due to noise, the HPD debounce
> may be 1.8ms, exceeding the default irq detect window, ~1.4ms.
> This patch set HPD irq detection window to 2ms to
> tolerate the HPD noise.
>
> Signed-off-by: Xin Ji <xji@analogixsemi.com>
> ---
> drivers/gpu/drm/bridge/analogix/anx7625.c | 14 ++++++++++++++
> drivers/gpu/drm/bridge/analogix/anx7625.h | 6 ++++++
> 2 files changed, 20 insertions(+)
>
> diff --git a/drivers/gpu/drm/bridge/analogix/anx7625.c b/drivers/gpu/drm/bridge/analogix/anx7625.c
> index c74b5df4cade..0c323b5a1c99 100644
> --- a/drivers/gpu/drm/bridge/analogix/anx7625.c
> +++ b/drivers/gpu/drm/bridge/analogix/anx7625.c
> @@ -1440,6 +1440,20 @@ static void anx7625_start_dp_work(struct anx7625_data *ctx)
>
> static int anx7625_read_hpd_status_p0(struct anx7625_data *ctx)
> {
> + int ret;
> +
> + /* Set irq detect window to 2ms */
> + ret = anx7625_reg_write(ctx, ctx->i2c.tx_p2_client,
> + HPD_DET_TIMER_BIT0_7, HPD_TIME & 0xFF);
> + ret |= anx7625_reg_write(ctx, ctx->i2c.tx_p2_client,
> + HPD_DET_TIMER_BIT8_15,
> + (HPD_TIME >> 8) & 0xFF);
> + ret |= anx7625_reg_write(ctx, ctx->i2c.tx_p2_client,
> + HPD_DET_TIMER_BIT16_23,
> + (HPD_TIME >> 16) & 0xFF);
Does the HPD debounce timer register need to be written for every HPD
status read?
> + if (ret < 0)
> + return ret;
> +
> return anx7625_reg_read(ctx, ctx->i2c.rx_p0_client, SYSTEM_STSTUS);
> }
>
> diff --git a/drivers/gpu/drm/bridge/analogix/anx7625.h b/drivers/gpu/drm/bridge/analogix/anx7625.h
> index e257a84db962..14f33d6be289 100644
> --- a/drivers/gpu/drm/bridge/analogix/anx7625.h
> +++ b/drivers/gpu/drm/bridge/analogix/anx7625.h
> @@ -132,6 +132,12 @@
> #define I2S_SLAVE_MODE 0x08
> #define AUDIO_LAYOUT 0x01
>
> +#define HPD_DET_TIMER_BIT0_7 0xea
> +#define HPD_DET_TIMER_BIT8_15 0xeb
> +#define HPD_DET_TIMER_BIT16_23 0xec
> +/* HPD debounce time 2ms for 27M clock */
> +#define HPD_TIME 54000
> +
> #define AUDIO_CONTROL_REGISTER 0xe6
> #define TDM_TIMING_MODE 0x08
>
> --
> 2.25.1
>
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [PATCH] drm/bridge: anx7625: Set HPD irq detect window to 2ms
2022-09-05 16:48 ` Robert Foss
@ 2022-09-06 2:57 ` Xin Ji
2022-09-06 12:10 ` Robert Foss
0 siblings, 1 reply; 4+ messages in thread
From: Xin Ji @ 2022-09-06 2:57 UTC (permalink / raw)
To: Robert Foss
Cc: Andrzej Hajda, Neil Armstrong, Laurent Pinchart, Jonas Karlman,
Jernej Skrabec, David Airlie, Daniel Vetter, bliang, qwen, mliu,
hsinyi, dri-devel, linux-kernel
On Mon, Sep 05, 2022 at 06:48:06PM +0200, Robert Foss wrote:
> Hi Xin,
>
> On Sat, 3 Sept 2022 at 15:09, Xin Ji <xji@analogixsemi.com> wrote:
> >
> > Some panels trigger HPD irq due to noise, the HPD debounce
> > may be 1.8ms, exceeding the default irq detect window, ~1.4ms.
> > This patch set HPD irq detection window to 2ms to
> > tolerate the HPD noise.
> >
> > Signed-off-by: Xin Ji <xji@analogixsemi.com>
> > ---
> > drivers/gpu/drm/bridge/analogix/anx7625.c | 14 ++++++++++++++
> > drivers/gpu/drm/bridge/analogix/anx7625.h | 6 ++++++
> > 2 files changed, 20 insertions(+)
> >
> > diff --git a/drivers/gpu/drm/bridge/analogix/anx7625.c b/drivers/gpu/drm/bridge/analogix/anx7625.c
> > index c74b5df4cade..0c323b5a1c99 100644
> > --- a/drivers/gpu/drm/bridge/analogix/anx7625.c
> > +++ b/drivers/gpu/drm/bridge/analogix/anx7625.c
> > @@ -1440,6 +1440,20 @@ static void anx7625_start_dp_work(struct anx7625_data *ctx)
> >
> > static int anx7625_read_hpd_status_p0(struct anx7625_data *ctx)
> > {
> > + int ret;
> > +
> > + /* Set irq detect window to 2ms */
> > + ret = anx7625_reg_write(ctx, ctx->i2c.tx_p2_client,
> > + HPD_DET_TIMER_BIT0_7, HPD_TIME & 0xFF);
> > + ret |= anx7625_reg_write(ctx, ctx->i2c.tx_p2_client,
> > + HPD_DET_TIMER_BIT8_15,
> > + (HPD_TIME >> 8) & 0xFF);
> > + ret |= anx7625_reg_write(ctx, ctx->i2c.tx_p2_client,
> > + HPD_DET_TIMER_BIT16_23,
> > + (HPD_TIME >> 16) & 0xFF);
>
> Does the HPD debounce timer register need to be written for every HPD
> status read?
Hi Robert Foss, yes, it is better to set it in every HPD status check, because the
HPD may be affected by noise, once the chip detect HPD is low, the timer
register will be automatically set to 1.4ms, so the driver better set it
in each check loop.
Thanks,
Xin
>
> > + if (ret < 0)
> > + return ret;
> > +
> > return anx7625_reg_read(ctx, ctx->i2c.rx_p0_client, SYSTEM_STSTUS);
> > }
> >
> > diff --git a/drivers/gpu/drm/bridge/analogix/anx7625.h b/drivers/gpu/drm/bridge/analogix/anx7625.h
> > index e257a84db962..14f33d6be289 100644
> > --- a/drivers/gpu/drm/bridge/analogix/anx7625.h
> > +++ b/drivers/gpu/drm/bridge/analogix/anx7625.h
> > @@ -132,6 +132,12 @@
> > #define I2S_SLAVE_MODE 0x08
> > #define AUDIO_LAYOUT 0x01
> >
> > +#define HPD_DET_TIMER_BIT0_7 0xea
> > +#define HPD_DET_TIMER_BIT8_15 0xeb
> > +#define HPD_DET_TIMER_BIT16_23 0xec
> > +/* HPD debounce time 2ms for 27M clock */
> > +#define HPD_TIME 54000
> > +
> > #define AUDIO_CONTROL_REGISTER 0xe6
> > #define TDM_TIMING_MODE 0x08
> >
> > --
> > 2.25.1
> >
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [PATCH] drm/bridge: anx7625: Set HPD irq detect window to 2ms
2022-09-06 2:57 ` Xin Ji
@ 2022-09-06 12:10 ` Robert Foss
0 siblings, 0 replies; 4+ messages in thread
From: Robert Foss @ 2022-09-06 12:10 UTC (permalink / raw)
To: Xin Ji
Cc: Andrzej Hajda, Neil Armstrong, Laurent Pinchart, Jonas Karlman,
Jernej Skrabec, David Airlie, Daniel Vetter, bliang, qwen, mliu,
hsinyi, dri-devel, linux-kernel
On Tue, 6 Sept 2022 at 04:58, Xin Ji <xji@analogixsemi.com> wrote:
>
> On Mon, Sep 05, 2022 at 06:48:06PM +0200, Robert Foss wrote:
> > Hi Xin,
> >
> > On Sat, 3 Sept 2022 at 15:09, Xin Ji <xji@analogixsemi.com> wrote:
> > >
> > > Some panels trigger HPD irq due to noise, the HPD debounce
> > > may be 1.8ms, exceeding the default irq detect window, ~1.4ms.
> > > This patch set HPD irq detection window to 2ms to
> > > tolerate the HPD noise.
> > >
> > > Signed-off-by: Xin Ji <xji@analogixsemi.com>
> > > ---
> > > drivers/gpu/drm/bridge/analogix/anx7625.c | 14 ++++++++++++++
> > > drivers/gpu/drm/bridge/analogix/anx7625.h | 6 ++++++
> > > 2 files changed, 20 insertions(+)
> > >
> > > diff --git a/drivers/gpu/drm/bridge/analogix/anx7625.c b/drivers/gpu/drm/bridge/analogix/anx7625.c
> > > index c74b5df4cade..0c323b5a1c99 100644
> > > --- a/drivers/gpu/drm/bridge/analogix/anx7625.c
> > > +++ b/drivers/gpu/drm/bridge/analogix/anx7625.c
> > > @@ -1440,6 +1440,20 @@ static void anx7625_start_dp_work(struct anx7625_data *ctx)
> > >
> > > static int anx7625_read_hpd_status_p0(struct anx7625_data *ctx)
> > > {
> > > + int ret;
> > > +
> > > + /* Set irq detect window to 2ms */
> > > + ret = anx7625_reg_write(ctx, ctx->i2c.tx_p2_client,
> > > + HPD_DET_TIMER_BIT0_7, HPD_TIME & 0xFF);
> > > + ret |= anx7625_reg_write(ctx, ctx->i2c.tx_p2_client,
> > > + HPD_DET_TIMER_BIT8_15,
> > > + (HPD_TIME >> 8) & 0xFF);
> > > + ret |= anx7625_reg_write(ctx, ctx->i2c.tx_p2_client,
> > > + HPD_DET_TIMER_BIT16_23,
> > > + (HPD_TIME >> 16) & 0xFF);
> >
> > Does the HPD debounce timer register need to be written for every HPD
> > status read?
> Hi Robert Foss, yes, it is better to set it in every HPD status check, because the
> HPD may be affected by noise, once the chip detect HPD is low, the timer
> register will be automatically set to 1.4ms, so the driver better set it
> in each check loop.
>
> Thanks,
> Xin
> >
> > > + if (ret < 0)
> > > + return ret;
> > > +
> > > return anx7625_reg_read(ctx, ctx->i2c.rx_p0_client, SYSTEM_STSTUS);
> > > }
> > >
> > > diff --git a/drivers/gpu/drm/bridge/analogix/anx7625.h b/drivers/gpu/drm/bridge/analogix/anx7625.h
> > > index e257a84db962..14f33d6be289 100644
> > > --- a/drivers/gpu/drm/bridge/analogix/anx7625.h
> > > +++ b/drivers/gpu/drm/bridge/analogix/anx7625.h
> > > @@ -132,6 +132,12 @@
> > > #define I2S_SLAVE_MODE 0x08
> > > #define AUDIO_LAYOUT 0x01
> > >
> > > +#define HPD_DET_TIMER_BIT0_7 0xea
> > > +#define HPD_DET_TIMER_BIT8_15 0xeb
> > > +#define HPD_DET_TIMER_BIT16_23 0xec
> > > +/* HPD debounce time 2ms for 27M clock */
> > > +#define HPD_TIME 54000
> > > +
> > > #define AUDIO_CONTROL_REGISTER 0xe6
> > > #define TDM_TIMING_MODE 0x08
> > >
> > > --
> > > 2.25.1
> > >
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Applied to drm-misc-next.
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2022-09-06 12:10 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2022-09-03 13:08 [PATCH] drm/bridge: anx7625: Set HPD irq detect window to 2ms Xin Ji
2022-09-05 16:48 ` Robert Foss
2022-09-06 2:57 ` Xin Ji
2022-09-06 12:10 ` Robert Foss
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).