* [PATCH net-next v3 1/3] net: hinic: Convert the cmd code from decimal to hex to be more readable
@ 2022-11-02 6:16 Cai Huoqing
2022-11-02 6:16 ` [PATCH net-next v3 2/3] net: hinic: Add control command support for VF PMD driver in DPDK Cai Huoqing
2022-11-02 6:16 ` [PATCH net-next v3 3/3] net: hinic: Add support for configuration of rx-vlan-filter by ethtool Cai Huoqing
0 siblings, 2 replies; 3+ messages in thread
From: Cai Huoqing @ 2022-11-02 6:16 UTC (permalink / raw)
To: kuba
Cc: Cai Huoqing, David S. Miller, Eric Dumazet, Paolo Abeni,
Zhengchao Shao, Qiao Ma, Christophe JAILLET, Bin Chen, netdev,
linux-kernel
The print cmd code is in hex, so using hex cmd code intead of
decimal is easy to check the value with print info.
Signed-off-by: Cai Huoqing <cai.huoqing@linux.dev>
---
v1->v2:
1.Add net-next prefix.
The comments link: https://lore.kernel.org/lkml/20221027110241.0340abdf@kernel.org/
v2->v3:
1.Merge PATCH 3/3 to this series.
.../net/ethernet/huawei/hinic/hinic_hw_dev.h | 108 +++++++++---------
1 file changed, 52 insertions(+), 56 deletions(-)
diff --git a/drivers/net/ethernet/huawei/hinic/hinic_hw_dev.h b/drivers/net/ethernet/huawei/hinic/hinic_hw_dev.h
index d2d89b0a5ef0..abffd967a791 100644
--- a/drivers/net/ethernet/huawei/hinic/hinic_hw_dev.h
+++ b/drivers/net/ethernet/huawei/hinic/hinic_hw_dev.h
@@ -46,104 +46,100 @@ enum hinic_port_cmd {
HINIC_PORT_CMD_VF_REGISTER = 0x0,
HINIC_PORT_CMD_VF_UNREGISTER = 0x1,
- HINIC_PORT_CMD_CHANGE_MTU = 2,
+ HINIC_PORT_CMD_CHANGE_MTU = 0x2,
- HINIC_PORT_CMD_ADD_VLAN = 3,
- HINIC_PORT_CMD_DEL_VLAN = 4,
+ HINIC_PORT_CMD_ADD_VLAN = 0x3,
+ HINIC_PORT_CMD_DEL_VLAN = 0x4,
- HINIC_PORT_CMD_SET_PFC = 5,
+ HINIC_PORT_CMD_SET_PFC = 0x5,
- HINIC_PORT_CMD_SET_MAC = 9,
- HINIC_PORT_CMD_GET_MAC = 10,
- HINIC_PORT_CMD_DEL_MAC = 11,
+ HINIC_PORT_CMD_SET_MAC = 0x9,
+ HINIC_PORT_CMD_GET_MAC = 0xA,
+ HINIC_PORT_CMD_DEL_MAC = 0xB,
- HINIC_PORT_CMD_SET_RX_MODE = 12,
+ HINIC_PORT_CMD_SET_RX_MODE = 0xC,
- HINIC_PORT_CMD_GET_PAUSE_INFO = 20,
- HINIC_PORT_CMD_SET_PAUSE_INFO = 21,
+ HINIC_PORT_CMD_GET_PAUSE_INFO = 0x14,
+ HINIC_PORT_CMD_SET_PAUSE_INFO = 0x15,
- HINIC_PORT_CMD_GET_LINK_STATE = 24,
+ HINIC_PORT_CMD_GET_LINK_STATE = 0x18,
- HINIC_PORT_CMD_SET_LRO = 25,
+ HINIC_PORT_CMD_SET_LRO = 0x19,
- HINIC_PORT_CMD_SET_RX_CSUM = 26,
+ HINIC_PORT_CMD_SET_RX_CSUM = 0x1A,
- HINIC_PORT_CMD_SET_RX_VLAN_OFFLOAD = 27,
+ HINIC_PORT_CMD_SET_RX_VLAN_OFFLOAD = 0x1B,
- HINIC_PORT_CMD_GET_PORT_STATISTICS = 28,
+ HINIC_PORT_CMD_GET_PORT_STATISTICS = 0x1C,
- HINIC_PORT_CMD_CLEAR_PORT_STATISTICS = 29,
+ HINIC_PORT_CMD_CLEAR_PORT_STATISTICS = 0x1D,
- HINIC_PORT_CMD_GET_VPORT_STAT = 30,
+ HINIC_PORT_CMD_GET_VPORT_STAT = 0x1E,
- HINIC_PORT_CMD_CLEAN_VPORT_STAT = 31,
+ HINIC_PORT_CMD_CLEAN_VPORT_STAT = 0x1F,
- HINIC_PORT_CMD_GET_RSS_TEMPLATE_INDIR_TBL = 37,
+ HINIC_PORT_CMD_GET_RSS_TEMPLATE_INDIR_TBL = 0x25,
- HINIC_PORT_CMD_SET_PORT_STATE = 41,
+ HINIC_PORT_CMD_SET_PORT_STATE = 0x29,
- HINIC_PORT_CMD_SET_RSS_TEMPLATE_TBL = 43,
+ HINIC_PORT_CMD_SET_RSS_TEMPLATE_TBL = 0x2B,
+ HINIC_PORT_CMD_GET_RSS_TEMPLATE_TBL = 0x2C,
- HINIC_PORT_CMD_GET_RSS_TEMPLATE_TBL = 44,
+ HINIC_PORT_CMD_SET_RSS_HASH_ENGINE = 0x2D,
+ HINIC_PORT_CMD_GET_RSS_HASH_ENGINE = 0x2E,
- HINIC_PORT_CMD_SET_RSS_HASH_ENGINE = 45,
+ HINIC_PORT_CMD_GET_RSS_CTX_TBL = 0x2F,
+ HINIC_PORT_CMD_SET_RSS_CTX_TBL = 0x30,
- HINIC_PORT_CMD_GET_RSS_HASH_ENGINE = 46,
+ HINIC_PORT_CMD_RSS_TEMP_MGR = 0x31,
- HINIC_PORT_CMD_GET_RSS_CTX_TBL = 47,
+ HINIC_PORT_CMD_RD_LINE_TBL = 0x39,
- HINIC_PORT_CMD_SET_RSS_CTX_TBL = 48,
+ HINIC_PORT_CMD_RSS_CFG = 0x42,
- HINIC_PORT_CMD_RSS_TEMP_MGR = 49,
+ HINIC_PORT_CMD_FWCTXT_INIT = 0x45,
- HINIC_PORT_CMD_RD_LINE_TBL = 57,
+ HINIC_PORT_CMD_GET_LOOPBACK_MODE = 0x48,
+ HINIC_PORT_CMD_SET_LOOPBACK_MODE = 0x49,
- HINIC_PORT_CMD_RSS_CFG = 66,
+ HINIC_PORT_CMD_ENABLE_SPOOFCHK = 0x4E,
- HINIC_PORT_CMD_FWCTXT_INIT = 69,
+ HINIC_PORT_CMD_GET_MGMT_VERSION = 0x58,
- HINIC_PORT_CMD_GET_LOOPBACK_MODE = 72,
- HINIC_PORT_CMD_SET_LOOPBACK_MODE,
+ HINIC_PORT_CMD_SET_FUNC_STATE = 0x5D,
- HINIC_PORT_CMD_ENABLE_SPOOFCHK = 78,
+ HINIC_PORT_CMD_GET_GLOBAL_QPN = 0x66,
- HINIC_PORT_CMD_GET_MGMT_VERSION = 88,
+ HINIC_PORT_CMD_SET_VF_RATE = 0x69,
- HINIC_PORT_CMD_SET_FUNC_STATE = 93,
+ HINIC_PORT_CMD_SET_VF_VLAN = 0x6A,
+ HINIC_PORT_CMD_CLR_VF_VLAN = 0x6B,
- HINIC_PORT_CMD_GET_GLOBAL_QPN = 102,
+ HINIC_PORT_CMD_SET_TSO = 0x70,
- HINIC_PORT_CMD_SET_VF_RATE = 105,
+ HINIC_PORT_CMD_UPDATE_FW = 0x72,
- HINIC_PORT_CMD_SET_VF_VLAN = 106,
+ HINIC_PORT_CMD_SET_RQ_IQ_MAP = 0x73,
- HINIC_PORT_CMD_CLR_VF_VLAN,
+ HINIC_PORT_CMD_LINK_STATUS_REPORT = 0xA0,
- HINIC_PORT_CMD_SET_TSO = 112,
+ HINIC_PORT_CMD_UPDATE_MAC = 0xA4,
- HINIC_PORT_CMD_UPDATE_FW = 114,
+ HINIC_PORT_CMD_GET_CAP = 0xAA,
- HINIC_PORT_CMD_SET_RQ_IQ_MAP = 115,
+ HINIC_PORT_CMD_GET_LINK_MODE = 0xD9,
- HINIC_PORT_CMD_LINK_STATUS_REPORT = 160,
+ HINIC_PORT_CMD_SET_SPEED = 0xDA,
- HINIC_PORT_CMD_UPDATE_MAC = 164,
+ HINIC_PORT_CMD_SET_AUTONEG = 0xDB,
- HINIC_PORT_CMD_GET_CAP = 170,
+ HINIC_PORT_CMD_GET_STD_SFP_INFO = 0xF0,
- HINIC_PORT_CMD_GET_LINK_MODE = 217,
+ HINIC_PORT_CMD_SET_LRO_TIMER = 0xF4,
- HINIC_PORT_CMD_SET_SPEED = 218,
+ HINIC_PORT_CMD_SET_VF_MAX_MIN_RATE = 0xF9,
- HINIC_PORT_CMD_SET_AUTONEG = 219,
-
- HINIC_PORT_CMD_GET_STD_SFP_INFO = 240,
-
- HINIC_PORT_CMD_SET_LRO_TIMER = 244,
-
- HINIC_PORT_CMD_SET_VF_MAX_MIN_RATE = 249,
-
- HINIC_PORT_CMD_GET_SFP_ABS = 251,
+ HINIC_PORT_CMD_GET_SFP_ABS = 0xFB,
};
/* cmd of mgmt CPU message for HILINK module */
--
2.25.1
^ permalink raw reply related [flat|nested] 3+ messages in thread
* [PATCH net-next v3 2/3] net: hinic: Add control command support for VF PMD driver in DPDK
2022-11-02 6:16 [PATCH net-next v3 1/3] net: hinic: Convert the cmd code from decimal to hex to be more readable Cai Huoqing
@ 2022-11-02 6:16 ` Cai Huoqing
2022-11-02 6:16 ` [PATCH net-next v3 3/3] net: hinic: Add support for configuration of rx-vlan-filter by ethtool Cai Huoqing
1 sibling, 0 replies; 3+ messages in thread
From: Cai Huoqing @ 2022-11-02 6:16 UTC (permalink / raw)
To: kuba
Cc: Cai Huoqing, David S. Miller, Eric Dumazet, Paolo Abeni,
Zhengchao Shao, Qiao Ma, Christophe JAILLET, Bin Chen, netdev,
linux-kernel
HINIC has a mailbox for PF-VF communication and the VF driver
could send port control command to PF driver via mailbox.
The control command only can be set to register in PF,
so add support in PF driver for VF PMD driver control
command when VF PMD driver work with linux PF driver.
Then, no need to add handlers to nic_vf_cmd_msg_handler[],
because the host driver just forwards it to the firmware.
Actually the firmware works on a coprocessor MGMT_CPU(inside the NIC)
which will recv and deal with these commands.
Signed-off-by: Cai Huoqing <cai.huoqing@linux.dev>
---
v1->v2:
1.Update the commit messsage.
2.Add net-next prefix.
The comments link: https://lore.kernel.org/lkml/20221031195805.74e22089@kernel.org/
v2->v3:
1.Merge PATCH 3/3 to this series.
.../net/ethernet/huawei/hinic/hinic_hw_dev.h | 64 +++++++++++++++++++
.../net/ethernet/huawei/hinic/hinic_sriov.c | 18 ++++++
2 files changed, 82 insertions(+)
diff --git a/drivers/net/ethernet/huawei/hinic/hinic_hw_dev.h b/drivers/net/ethernet/huawei/hinic/hinic_hw_dev.h
index abffd967a791..4f561e4e849a 100644
--- a/drivers/net/ethernet/huawei/hinic/hinic_hw_dev.h
+++ b/drivers/net/ethernet/huawei/hinic/hinic_hw_dev.h
@@ -53,11 +53,15 @@ enum hinic_port_cmd {
HINIC_PORT_CMD_SET_PFC = 0x5,
+ HINIC_PORT_CMD_SET_ETS = 0x7,
+ HINIC_PORT_CMD_GET_ETS = 0x8,
+
HINIC_PORT_CMD_SET_MAC = 0x9,
HINIC_PORT_CMD_GET_MAC = 0xA,
HINIC_PORT_CMD_DEL_MAC = 0xB,
HINIC_PORT_CMD_SET_RX_MODE = 0xC,
+ HINIC_PORT_CMD_SET_ANTI_ATTACK_RATE = 0xD,
HINIC_PORT_CMD_GET_PAUSE_INFO = 0x14,
HINIC_PORT_CMD_SET_PAUSE_INFO = 0x15,
@@ -81,6 +85,7 @@ enum hinic_port_cmd {
HINIC_PORT_CMD_GET_RSS_TEMPLATE_INDIR_TBL = 0x25,
HINIC_PORT_CMD_SET_PORT_STATE = 0x29,
+ HINIC_PORT_CMD_GET_PORT_STATE = 0x30,
HINIC_PORT_CMD_SET_RSS_TEMPLATE_TBL = 0x2B,
HINIC_PORT_CMD_GET_RSS_TEMPLATE_TBL = 0x2C,
@@ -97,17 +102,29 @@ enum hinic_port_cmd {
HINIC_PORT_CMD_RSS_CFG = 0x42,
+ HINIC_PORT_CMD_GET_PHY_TYPE = 0x44,
+
HINIC_PORT_CMD_FWCTXT_INIT = 0x45,
HINIC_PORT_CMD_GET_LOOPBACK_MODE = 0x48,
HINIC_PORT_CMD_SET_LOOPBACK_MODE = 0x49,
+ HINIC_PORT_CMD_GET_JUMBO_FRAME_SIZE = 0x4A,
+ HINIC_PORT_CMD_SET_JUMBO_FRAME_SIZE = 0x4B,
+
HINIC_PORT_CMD_ENABLE_SPOOFCHK = 0x4E,
HINIC_PORT_CMD_GET_MGMT_VERSION = 0x58,
+ HINIC_PORT_CMD_GET_PORT_TYPE = 0x5B,
+
HINIC_PORT_CMD_SET_FUNC_STATE = 0x5D,
+ HINIC_PORT_CMD_GET_PORT_ID_BY_FUNC_ID = 0x5E,
+
+ HINIC_PORT_CMD_GET_DMA_CS = 0x64,
+ HINIC_PORT_CMD_SET_DMA_CS = 0x65,
+
HINIC_PORT_CMD_GET_GLOBAL_QPN = 0x66,
HINIC_PORT_CMD_SET_VF_RATE = 0x69,
@@ -121,25 +138,72 @@ enum hinic_port_cmd {
HINIC_PORT_CMD_SET_RQ_IQ_MAP = 0x73,
+ HINIC_PORT_CMD_SET_PFC_THD = 0x75,
+
HINIC_PORT_CMD_LINK_STATUS_REPORT = 0xA0,
+ HINIC_PORT_CMD_SET_LOSSLESS_ETH = 0xA3,
+
HINIC_PORT_CMD_UPDATE_MAC = 0xA4,
HINIC_PORT_CMD_GET_CAP = 0xAA,
+ HINIC_PORT_CMD_UP_TC_ADD_FLOW = 0xAF,
+ HINIC_PORT_CMD_UP_TC_DEL_FLOW = 0xB0,
+ HINIC_PORT_CMD_UP_TC_GET_FLOW = 0xB1,
+
+ HINIC_PORT_CMD_UP_TC_FLUSH_TCAM = 0xB2,
+
+ HINIC_PORT_CMD_UP_TC_CTRL_TCAM_BLOCK = 0xB3,
+
+ HINIC_PORT_CMD_UP_TC_ENABLE = 0xB4,
+
+ HINIC_PORT_CMD_UP_TC_GET_TCAM_BLOCK = 0xB5,
+
+ HINIC_PORT_CMD_SET_IPSU_MAC = 0xCB,
+ HINIC_PORT_CMD_GET_IPSU_MAC = 0xCC,
+
+ HINIC_PORT_CMD_SET_XSFP_STATUS = 0xD4,
HINIC_PORT_CMD_GET_LINK_MODE = 0xD9,
HINIC_PORT_CMD_SET_SPEED = 0xDA,
HINIC_PORT_CMD_SET_AUTONEG = 0xDB,
+ HINIC_PORT_CMD_CLEAR_QP_RES = 0xDD,
+
+ HINIC_PORT_CMD_SET_SUPER_CQE = 0xDE,
+
+ HINIC_PORT_CMD_SET_VF_COS = 0xDF,
+ HINIC_PORT_CMD_GET_VF_COS = 0xE1,
+
+ HINIC_PORT_CMD_CABLE_PLUG_EVENT = 0xE5,
+
+ HINIC_PORT_CMD_LINK_ERR_EVENT = 0xE6,
+
+ HINIC_PORT_CMD_SET_COS_UP_MAP = 0xE8,
+
+ HINIC_PORT_CMD_RESET_LINK_CFG = 0xEB,
+
HINIC_PORT_CMD_GET_STD_SFP_INFO = 0xF0,
+ HINIC_PORT_CMD_FORCE_PKT_DROP = 0xF3,
+
HINIC_PORT_CMD_SET_LRO_TIMER = 0xF4,
+ HINIC_PORT_CMD_SET_VHD_CFG = 0xF7,
+
+ HINIC_PORT_CMD_SET_LINK_FOLLOW = 0xF8,
+
HINIC_PORT_CMD_SET_VF_MAX_MIN_RATE = 0xF9,
HINIC_PORT_CMD_GET_SFP_ABS = 0xFB,
+
+ HINIC_PORT_CMD_Q_FILTER = 0xFC,
+
+ HINIC_PORT_CMD_TCAM_FILTER = 0xFE,
+
+ HINIC_PORT_CMD_SET_VLAN_FILTER = 0xFF
};
/* cmd of mgmt CPU message for HILINK module */
diff --git a/drivers/net/ethernet/huawei/hinic/hinic_sriov.c b/drivers/net/ethernet/huawei/hinic/hinic_sriov.c
index f7e05b41385b..ee357088d021 100644
--- a/drivers/net/ethernet/huawei/hinic/hinic_sriov.c
+++ b/drivers/net/ethernet/huawei/hinic/hinic_sriov.c
@@ -489,6 +489,24 @@ static struct vf_cmd_check_handle nic_cmd_support_vf[] = {
{HINIC_PORT_CMD_UPDATE_MAC, hinic_mbox_check_func_id_8B},
{HINIC_PORT_CMD_GET_CAP, hinic_mbox_check_func_id_8B},
{HINIC_PORT_CMD_GET_LINK_MODE, hinic_mbox_check_func_id_8B},
+ {HINIC_PORT_CMD_GET_VF_COS, NULL},
+ {HINIC_PORT_CMD_SET_VHD_CFG, hinic_mbox_check_func_id_8B},
+ {HINIC_PORT_CMD_SET_VLAN_FILTER, hinic_mbox_check_func_id_8B},
+ {HINIC_PORT_CMD_Q_FILTER, hinic_mbox_check_func_id_8B},
+ {HINIC_PORT_CMD_TCAM_FILTER, NULL},
+ {HINIC_PORT_CMD_UP_TC_ADD_FLOW, NULL},
+ {HINIC_PORT_CMD_UP_TC_DEL_FLOW, NULL},
+ {HINIC_PORT_CMD_UP_TC_FLUSH_TCAM, hinic_mbox_check_func_id_8B},
+ {HINIC_PORT_CMD_UP_TC_CTRL_TCAM_BLOCK, hinic_mbox_check_func_id_8B},
+ {HINIC_PORT_CMD_UP_TC_ENABLE, hinic_mbox_check_func_id_8B},
+ {HINIC_PORT_CMD_CABLE_PLUG_EVENT, NULL},
+ {HINIC_PORT_CMD_LINK_ERR_EVENT, NULL},
+ {HINIC_PORT_CMD_SET_PORT_STATE, hinic_mbox_check_func_id_8B},
+ {HINIC_PORT_CMD_SET_ETS, NULL},
+ {HINIC_PORT_CMD_SET_ANTI_ATTACK_RATE, NULL},
+ {HINIC_PORT_CMD_RESET_LINK_CFG, hinic_mbox_check_func_id_8B},
+ {HINIC_PORT_CMD_SET_LINK_FOLLOW, NULL},
+ {HINIC_PORT_CMD_CLEAR_QP_RES, NULL},
};
#define CHECK_IPSU_15BIT 0X8000
--
2.25.1
^ permalink raw reply related [flat|nested] 3+ messages in thread
* [PATCH net-next v3 3/3] net: hinic: Add support for configuration of rx-vlan-filter by ethtool
2022-11-02 6:16 [PATCH net-next v3 1/3] net: hinic: Convert the cmd code from decimal to hex to be more readable Cai Huoqing
2022-11-02 6:16 ` [PATCH net-next v3 2/3] net: hinic: Add control command support for VF PMD driver in DPDK Cai Huoqing
@ 2022-11-02 6:16 ` Cai Huoqing
1 sibling, 0 replies; 3+ messages in thread
From: Cai Huoqing @ 2022-11-02 6:16 UTC (permalink / raw)
To: kuba
Cc: Cai Huoqing, David S. Miller, Eric Dumazet, Paolo Abeni,
Zhengchao Shao, Christophe JAILLET, Qiao Ma, Bin Chen, netdev,
linux-kernel
When ethtool config rx-vlan-filter, the driver will send
control command to firmware, then set to hardware in this patch.
Signed-off-by: Cai Huoqing <cai.huoqing@linux.dev>
---
v1->v3:
1.Merge this patch to the series.
comments link: https://lore.kernel.org/lkml/20221101214059.464a1d42@kernel.org/
.../net/ethernet/huawei/hinic/hinic_main.c | 10 ++++++
.../net/ethernet/huawei/hinic/hinic_port.c | 33 +++++++++++++++++++
.../net/ethernet/huawei/hinic/hinic_port.h | 12 +++++++
3 files changed, 55 insertions(+)
diff --git a/drivers/net/ethernet/huawei/hinic/hinic_main.c b/drivers/net/ethernet/huawei/hinic/hinic_main.c
index 9d4d795e1081..977c41473ab7 100644
--- a/drivers/net/ethernet/huawei/hinic/hinic_main.c
+++ b/drivers/net/ethernet/huawei/hinic/hinic_main.c
@@ -1092,6 +1092,16 @@ static int set_features(struct hinic_dev *nic_dev,
}
}
+ if (changed & NETIF_F_HW_VLAN_CTAG_FILTER) {
+ ret = hinic_set_vlan_fliter(nic_dev,
+ !!(features &
+ NETIF_F_HW_VLAN_CTAG_FILTER));
+ if (ret) {
+ err = ret;
+ failed_features |= NETIF_F_HW_VLAN_CTAG_FILTER;
+ }
+ }
+
if (err) {
nic_dev->netdev->features = features ^ failed_features;
return -EIO;
diff --git a/drivers/net/ethernet/huawei/hinic/hinic_port.c b/drivers/net/ethernet/huawei/hinic/hinic_port.c
index 0a39c3dffa9a..9406237c461e 100644
--- a/drivers/net/ethernet/huawei/hinic/hinic_port.c
+++ b/drivers/net/ethernet/huawei/hinic/hinic_port.c
@@ -447,6 +447,39 @@ int hinic_set_rx_vlan_offload(struct hinic_dev *nic_dev, u8 en)
return 0;
}
+int hinic_set_vlan_fliter(struct hinic_dev *nic_dev, u32 en)
+{
+ struct hinic_hwdev *hwdev = nic_dev->hwdev;
+ struct hinic_hwif *hwif = hwdev->hwif;
+ struct pci_dev *pdev = hwif->pdev;
+ struct hinic_vlan_filter vlan_filter;
+ u16 out_size = sizeof(vlan_filter);
+ int err;
+
+ if (!hwdev)
+ return -EINVAL;
+
+ vlan_filter.func_idx = HINIC_HWIF_FUNC_IDX(hwif);
+ vlan_filter.enable = en;
+
+ err = hinic_port_msg_cmd(hwdev, HINIC_PORT_CMD_SET_VLAN_FILTER,
+ &vlan_filter, sizeof(vlan_filter),
+ &vlan_filter, &out_size);
+ if (vlan_filter.status == HINIC_MGMT_CMD_UNSUPPORTED) {
+ err = HINIC_MGMT_CMD_UNSUPPORTED;
+ } else if ((err == HINIC_MBOX_VF_CMD_ERROR) &&
+ HINIC_IS_VF(hwif)) {
+ err = HINIC_MGMT_CMD_UNSUPPORTED;
+ } else if (err || !out_size || vlan_filter.status) {
+ dev_err(&pdev->dev,
+ "Failed to set vlan fliter, err: %d, status: 0x%x, out size: 0x%x\n",
+ err, vlan_filter.status, out_size);
+ err = -EINVAL;
+ }
+
+ return err;
+}
+
int hinic_set_max_qnum(struct hinic_dev *nic_dev, u8 num_rqs)
{
struct hinic_hwdev *hwdev = nic_dev->hwdev;
diff --git a/drivers/net/ethernet/huawei/hinic/hinic_port.h b/drivers/net/ethernet/huawei/hinic/hinic_port.h
index c9ae3d4dc547..c8694ac7c702 100644
--- a/drivers/net/ethernet/huawei/hinic/hinic_port.h
+++ b/drivers/net/ethernet/huawei/hinic/hinic_port.h
@@ -351,6 +351,16 @@ struct hinic_vlan_cfg {
u8 rsvd1[5];
};
+struct hinic_vlan_filter {
+ u8 status;
+ u8 version;
+ u8 rsvd0[6];
+
+ u16 func_idx;
+ u8 rsvd1[2];
+ u32 enable;
+};
+
struct hinic_rss_template_mgmt {
u8 status;
u8 version;
@@ -831,6 +841,8 @@ int hinic_get_vport_stats(struct hinic_dev *nic_dev,
int hinic_set_rx_vlan_offload(struct hinic_dev *nic_dev, u8 en);
+int hinic_set_vlan_fliter(struct hinic_dev *nic_dev, u32 en);
+
int hinic_get_mgmt_version(struct hinic_dev *nic_dev, u8 *mgmt_ver);
int hinic_set_link_settings(struct hinic_hwdev *hwdev,
--
2.25.1
^ permalink raw reply related [flat|nested] 3+ messages in thread
end of thread, other threads:[~2022-11-02 6:17 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2022-11-02 6:16 [PATCH net-next v3 1/3] net: hinic: Convert the cmd code from decimal to hex to be more readable Cai Huoqing
2022-11-02 6:16 ` [PATCH net-next v3 2/3] net: hinic: Add control command support for VF PMD driver in DPDK Cai Huoqing
2022-11-02 6:16 ` [PATCH net-next v3 3/3] net: hinic: Add support for configuration of rx-vlan-filter by ethtool Cai Huoqing
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).