* [PATCH v3 0/8] Add MSM8939 SoC support with two devices
@ 2023-01-17 2:48 Bryan O'Donoghue
2023-01-17 2:48 ` [PATCH v3 1/8] dt-bindings: arm: qcom: Document MSM8939 SoC binding Bryan O'Donoghue
` (8 more replies)
0 siblings, 9 replies; 32+ messages in thread
From: Bryan O'Donoghue @ 2023-01-17 2:48 UTC (permalink / raw)
To: agross, andersson, konrad.dybcio, djakov, robh+dt,
krzysztof.kozlowski+dt
Cc: bryan.odonoghue, linux-arm-msm, linux-pm, devicetree,
linux-kernel, benl, shawn.guo, fabien.parent, leo.yan,
dmitry.baryshkov
V3:
- Happily I don't currently depend on any other series to be merged.
Bjorn and Chanwoo picked up everything I need to unblock this series. ＼(^o^)／
- Moves xo_board to RPM/PMIC clock gated CXO, not including rpmcc: obvs - Konrad/Bjorn
- qcom,msm-id = <239 0> - left as in V2 valid according to Sony references - bod
- cpu-release-addr - as stated below we rely on lk2nd to take the second cluster
out of reset - bod
- smem child node update - Konrad
- Whitespace updates - Konrad
- gpu no interconnect - Konrad - No bod
- 19.2 MHz dropped from timer@b020000 - Konrad
- Added vreg_dummy comment - Konrad
- sdc_pins grouped - Konrad
- startup-delay-us = <0> - left as is
- bias - added no-bias - Konrad
- :g/msmgpio/s//tlmm/g - Konrad
- mdss/s//display-controller - Konrad
- l11 set-load - Korad
- l12 upper voltage raised to 3.3v since this is what the
downstream kernel says when I boot and interrogate it - bod
- sdhc@address - Discussed with Krzysztof and implemented as discussed
- snoc-mm fix - Discussed with Krzysztof implemented if:then:else:not
- dtc -I dtb -fs apq8039-t2.dtb prodcues
/soc@0/i2c@78b5000: duplicate unit-address
as does every other component that uses this polymorphic dts node
- Renamed type-c i2c port manager IC to "typec" - Krzysztof
/smsm/hexagon@1: Missing #address-cells in interrupt provider
Same output as other upstream and recently upstreamed SoCs
I left these alone for now
link: https://lore.kernel.org/lkml/20230103010904.3201835-1-bryan.odonoghue@linaro.org/T/
bootable: https://git.linaro.org/people/bryan.odonoghue/kernel.git/log/?h=linux-next-23-01-16-msm8939-nocpr
V2:
- Sorts core dtsi node list by address followed by alpahbetical sorting
within address sorted nodes - Bjorn
- Drops use of 8916-pins - Bjorn
- Adds msm8939-pm8916.dtsi - Stephan
- Fixes every dts splat from previous submission minus non-converted
.txt compat strings [1] and one yaml error in Bjorn's tree not in -next yet
- I haven't applied Dmitry's change for tsens since that's not been
picked up yet
- Picks up a number of suggestions and fixes from Stephan Gerhold and Vincent Knecht
- Depends on
Applied:
[PATCH v4 0/7] remoteproc: qcom_q6v5_mss: Add MSM8909 and MSM8953
https://lore.kernel.org/linux-arm-msm/167216232800.738877.17567287056128563074.b4-ty@kernel.org/
[PATCH v6 0/5] remoteproc: qcom: Add support for pronto-v3
https://lore.kernel.org/linux-arm-msm/167216232801.738877.15895916910585144737.b4-ty@kernel.org/
[PATCH v6 00/18] mdss-dsi-ctrl binding and dts fixes
https://lore.kernel.org/linux-arm-msm/167233461766.1099840.17628700245792986354.b4-ty@kernel.org/
Awaiting application:
https://lore.kernel.org/linux-arm-msm/20221228133058.213886-1-bryan.odonoghue@linaro.org/
- Previous
https://lore.kernel.org/linux-arm-msm/20220419010903.3109514-1-bryan.odonoghue@linaro.org/
- Bootable tree
https://git.linaro.org/people/bryan.odonoghue/kernel.git/log/?h=linux-next-23-01-03-msm8939-no-cpr
- [1] DTC_CHK arch/arm64/boot/dts/qcom/apq8039-t2.dtb
Documentation/devicetree/bindings/arm/msm/qcom,idle-state.txt
qcom/apq8039-t2.dtb: idle-states: cpu-sleep-0:compatible:0: 'qcom,idle-state-spc' is not one of ['arm,idle-state', 'riscv,idle-state']
From schema: Documentation/devicetree/bindings/cpu/idle-states.yaml
qcom/apq8039-t2.dtb: idle-states: cpu-sleep-0:compatible: ['qcom,idle-state-spc', 'arm,idle-state'] is too long
From schema: Documentation/devicetree/bindings/cpu/idle-states.yaml
arch/arm64/boot/dts/qcom/apq8039-t2.dtb:0:0: /cpus/idle-states/cpu-sleep-0: failed to match any schema with compatible: ['qcom,idle-state-spc', 'arm,idle-state']
Documentation/devicetree/bindings/iommu/qcom,iommu.txt
arch/arm64/boot/dts/qcom/apq8039-t2.dtb:0:0: /soc@0/iommu@1ef0000: failed to match any schema with compatible: ['qcom,msm8916-iommu', 'qcom,msm-iommu-v1']
arch/arm64/boot/dts/qcom/apq8039-t2.dtb:0:0: /soc@0/iommu@1ef0000/iommu-ctx@4000: failed to match any schema with compatible: ['qcom,msm-iommu-v1-ns']
arch/arm64/boot/dts/qcom/apq8039-t2.dtb:0:0: /soc@0/iommu@1ef0000/iommu-ctx@5000: failed to match any schema with compatible: ['qcom,msm-iommu-v1-sec']
arch/arm64/boot/dts/qcom/apq8039-t2.dtb:0:0: /soc@0/iommu@1f08000: failed to match any schema with compatible: ['qcom,msm8916-iommu', 'qcom,msm-iommu-v1']
arch/arm64/boot/dts/qcom/apq8039-t2.dtb:0:0: /soc@0/iommu@1f08000/iommu-ctx@1000: failed to match any schema with compatible: ['qcom,msm-iommu-v1-ns']
arch/arm64/boot/dts/qcom/apq8039-t2.dtb:0:0: /soc@0/iommu@1f08000/iommu-ctx@2000: failed to match any schema with compatible: ['qcom,msm-iommu-v1-ns']
arch/arm64/boot/dts/qcom/pm8916.dtsi f5d7bca55425c8
qcom/apq8039-t2.dtb: pmic@0: 'extcon@1300' does not match any of the regexes: '(.*)?(wled|leds)@[0-9a-f]+$', '^adc-tm@[0-9a-f]+$', '^adc@[0-9a-f]+$', '^audio-codec@[0-9a-f]+$', '^charger@[0-9a-f]+$', '^mpps@[0-9a-f]+$', '^rtc@[0-9a-f]+$', '^temp-alarm@[0-9a-f]+$', '^usb-detect@[0-9a-f]+$', '^usb-vbus-regulator@[0-9a-f]+$', '^vibrator@[0-9a-f]+$', 'gpio@[0-9a-f]+$', 'pinctrl-[0-9]+', 'pon@[0-9a-f]+$'
From schema: Documentation/devicetree/bindings/mfd/qcom,spmi-pmic.yaml
Documentation/devicetree/bindings/sound/qcom,msm8916-wcd-analog.txt
arch/arm64/boot/dts/qcom/apq8039-t2.dtb:0:0: /soc@0/spmi@200f000/pmic@1/audio-codec@f000: failed to match any schema with compatible: ['qcom,pm8916-wcd-analog-codec']
yaml documentation error not yet in -next
arm64/boot/dts/qcom/apq8039-t2.dtb: remoteproc@4080000: qcom,halt-regs:0: [33] is too short
From schema: Documentation/devicetree/bindings/remoteproc/qcom,msm8916-mss-pil.yaml
Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt
arch/arm64/boot/dts/qcom/apq8039-t2.dtb:0:0: /soc@0/usb@78d9000: failed to match any schema with compatible: ['qcom,ci-hdrc']
Documentation/devicetree/bindings/arm/msm/qcom,kpss-acc.txt: compatible = "qcom,kpss-acc-v2";
arch/arm64/boot/dts/qcom/apq8039-t2.dtb:0:0: /soc@0/clock-controller@b088000: failed to match any schema with compatible: ['qcom,kpss-acc-v2']
arch/arm64/boot/dts/qcom/apq8039-t2.dtb:0:0: /soc@0/clock-controller@b098000: failed to match any schema with compatible: ['qcom,kpss-acc-v2']
arch/arm64/boot/dts/qcom/apq8039-t2.dtb:0:0: /soc@0/clock-controller@b0a8000: failed to match any schema with compatible: ['qcom,kpss-acc-v2']
arch/arm64/boot/dts/qcom/apq8039-t2.dtb:0:0: /soc@0/clock-controller@b0b8000: failed to match any schema with compatible: ['qcom,kpss-acc-v2']
arch/arm64/boot/dts/qcom/apq8039-t2.dtb:0:0: /soc@0/clock-controller@b188000: failed to match any schema with compatible: ['qcom,kpss-acc-v2']
arch/arm64/boot/dts/qcom/apq8039-t2.dtb:0:0: /soc@0/clock-controller@b198000: failed to match any schema with compatible: ['qcom,kpss-acc-v2']
arch/arm64/boot/dts/qcom/apq8039-t2.dtb:0:0: /soc@0/clock-controller@b1a8000: failed to match any schema with compatible: ['qcom,kpss-acc-v2']
arch/arm64/boot/dts/qcom/apq8039-t2.dtb:0:0: /soc@0/clock-controller@b1b8000: failed to match any schema with compatible: ['qcom,kpss-acc-v2']
V1:
This series adds in MSM8939 SoC support with two supported devices.
- CPU
MSM8939 is a non-PSCI compliant device. As such in the downstreaming
shipped image custom code is used to bring non-boot cores out of reset.
This drop specifies the boot-method as spin-table instead and is
completely standard. To accomplish this, we rely on lk2nd.
https://github.com/msm8916-mainline/lk2nd/pull/142
- Serial
- i2c
- USB
- eMMC
- MDP/DSI
- WiFi
- Bluetooth
What's not included
- CPR
We have CPR working in a 4.19 kernel quite well but for now it feels like
putting the cart before the horse to gate the SoC and boards on CPR.
- Venus
I've been told this works but I haven't tried it myself and right now
consider it maybe working but probably not 100%.
- Sound
We have a copy-exactly from the 4.19 kernel here in the DTS.
I haven't run the sound through any sort of reasonable test.
Vincent Knecht has some PostmarketOS kernels which use a 5.17 version of
this DTS to get sound up so, I think sound is in good shape.
- CAMSS
There are slight differences between msm8916 and msm8939 for CAMSS. It
doesn't feel like tons of work but, right now it is work we haven't even
started.
- Devices
I've booted on the Square device obviously and this is my regular
hardware for upstream development. I've also booted on the Sony Xperia M4
Aqua including mutli-core bring-up, WiFi and ADB.
Dependencies for this drop:
qcom-cpufreq-nvmem: Add msm8939 with some fixups
link: https://lore.kernel.org/linux-arm-msm/20220418162226.2983117-1-bryan.odonoghue@linaro.org/T/#t
Fix apq8016 compat string
link: https://lore.kernel.org/linux-arm-msm/20220418230956.3059563-1-bryan.odonoghue@linaro.org/T/#t
dt-bindings: soc: qcom: smd-rpm: Fix missing MSM8936 compatible
link: https://lore.kernel.org/linux-arm-msm/20220418231857.3061053-1-bryan.odonoghue@linaro.org/T/#u
Bootable tree here:
https://git.linaro.org/people/bryan.odonoghue/kernel.git/log/?h=v5.18-rc2%2bapq8039-without-cpr
Bryan O'Donoghue (7):
dt-bindings: arm: qcom: Document MSM8939 SoC binding
dt-bindings: soc: qcom: smd-rpm: Exclude MSM8936 from glink-channels
dt-bindings: interconnect: Exclude all non msm8939 from snoc-mm
clk: qcom: smd-rpm: msm8936: Add PMIC gated RPM_SMD_XO_*
arm64: dts: qcom: Add msm8939 SoC
arm64: dts: qcom: Add Square apq8039-t2 board
arm64: dts: qcom: Add msm8939 Sony Xperia M4 Aqua
Stephan Gerhold (1):
arm64: dts: qcom: Add msm8939-pm8916.dtsi include
.../devicetree/bindings/arm/qcom.yaml | 8 +
.../bindings/interconnect/qcom,rpm.yaml | 73 +-
.../bindings/soc/qcom/qcom,smd-rpm.yaml | 1 +
arch/arm64/boot/dts/qcom/Makefile | 2 +
arch/arm64/boot/dts/qcom/apq8039-t2.dts | 555 ++++
arch/arm64/boot/dts/qcom/msm8939-pm8916.dtsi | 82 +
.../qcom/msm8939-sony-xperia-kanuti-tulip.dts | 466 ++++
arch/arm64/boot/dts/qcom/msm8939.dtsi | 2393 +++++++++++++++++
drivers/clk/qcom/clk-smd-rpm.c | 2 +
9 files changed, 3551 insertions(+), 31 deletions(-)
create mode 100644 arch/arm64/boot/dts/qcom/apq8039-t2.dts
create mode 100644 arch/arm64/boot/dts/qcom/msm8939-pm8916.dtsi
create mode 100644 arch/arm64/boot/dts/qcom/msm8939-sony-xperia-kanuti-tulip.dts
create mode 100644 arch/arm64/boot/dts/qcom/msm8939.dtsi
--
2.38.1
^ permalink raw reply [flat|nested] 32+ messages in thread
* [PATCH v3 1/8] dt-bindings: arm: qcom: Document MSM8939 SoC binding
2023-01-17 2:48 [PATCH v3 0/8] Add MSM8939 SoC support with two devices Bryan O'Donoghue
@ 2023-01-17 2:48 ` Bryan O'Donoghue
2023-01-18 8:47 ` Stephan Gerhold
2023-01-17 2:48 ` [PATCH v3 2/8] dt-bindings: soc: qcom: smd-rpm: Exclude MSM8936 from glink-channels Bryan O'Donoghue
` (7 subsequent siblings)
8 siblings, 1 reply; 32+ messages in thread
From: Bryan O'Donoghue @ 2023-01-17 2:48 UTC (permalink / raw)
To: agross, andersson, konrad.dybcio, djakov, robh+dt,
krzysztof.kozlowski+dt
Cc: bryan.odonoghue, linux-arm-msm, linux-pm, devicetree,
linux-kernel, benl, shawn.guo, fabien.parent, leo.yan,
dmitry.baryshkov, Krzysztof Kozlowski
Document the MSM8939 and supported boards in upstream Sony "Tulip" M4 Aqua
and Square APQ8039 T2.
MSM8939 is one of the older SoCs so we need to expand the list of
qcom,board-ids to allow for the bootloader DTS board-id matching
dependency.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
---
Documentation/devicetree/bindings/arm/qcom.yaml | 8 ++++++++
1 file changed, 8 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/qcom.yaml b/Documentation/devicetree/bindings/arm/qcom.yaml
index 47913a8e3eea3..0721d1a0b80e6 100644
--- a/Documentation/devicetree/bindings/arm/qcom.yaml
+++ b/Documentation/devicetree/bindings/arm/qcom.yaml
@@ -35,6 +35,7 @@ description: |
mdm9615
msm8226
msm8916
+ msm8939
msm8953
msm8956
msm8974
@@ -164,6 +165,12 @@ properties:
- samsung,s3ve3g
- const: qcom,msm8226
+ - items:
+ - enum:
+ - sony,kanuti-tulip
+ - square,apq8039-t2
+ - const: qcom,msm8939
+
- items:
- enum:
- sony,kugo-row
@@ -966,6 +973,7 @@ allOf:
- qcom,apq8026
- qcom,apq8094
- qcom,apq8096
+ - qcom,msm8939
- qcom,msm8953
- qcom,msm8956
- qcom,msm8992
--
2.38.1
^ permalink raw reply related [flat|nested] 32+ messages in thread
* [PATCH v3 2/8] dt-bindings: soc: qcom: smd-rpm: Exclude MSM8936 from glink-channels
2023-01-17 2:48 [PATCH v3 0/8] Add MSM8939 SoC support with two devices Bryan O'Donoghue
2023-01-17 2:48 ` [PATCH v3 1/8] dt-bindings: arm: qcom: Document MSM8939 SoC binding Bryan O'Donoghue
@ 2023-01-17 2:48 ` Bryan O'Donoghue
2023-01-17 2:48 ` [PATCH v3 3/8] dt-bindings: interconnect: Exclude all non msm8939 from snoc-mm Bryan O'Donoghue
` (6 subsequent siblings)
8 siblings, 0 replies; 32+ messages in thread
From: Bryan O'Donoghue @ 2023-01-17 2:48 UTC (permalink / raw)
To: agross, andersson, konrad.dybcio, djakov, robh+dt,
krzysztof.kozlowski+dt
Cc: bryan.odonoghue, linux-arm-msm, linux-pm, devicetree,
linux-kernel, benl, shawn.guo, fabien.parent, leo.yan,
dmitry.baryshkov, Krzysztof Kozlowski
MSM8936/MSM8939 should like MSM8916 not require glink-channels.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
---
Documentation/devicetree/bindings/soc/qcom/qcom,smd-rpm.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,smd-rpm.yaml b/Documentation/devicetree/bindings/soc/qcom/qcom,smd-rpm.yaml
index 11c0f4dd797ce..16fd67c0bd1fd 100644
--- a/Documentation/devicetree/bindings/soc/qcom/qcom,smd-rpm.yaml
+++ b/Documentation/devicetree/bindings/soc/qcom/qcom,smd-rpm.yaml
@@ -80,6 +80,7 @@ if:
enum:
- qcom,rpm-apq8084
- qcom,rpm-msm8916
+ - qcom,rpm-msm8936
- qcom,rpm-msm8974
- qcom,rpm-msm8976
- qcom,rpm-msm8953
--
2.38.1
^ permalink raw reply related [flat|nested] 32+ messages in thread
* [PATCH v3 3/8] dt-bindings: interconnect: Exclude all non msm8939 from snoc-mm
2023-01-17 2:48 [PATCH v3 0/8] Add MSM8939 SoC support with two devices Bryan O'Donoghue
2023-01-17 2:48 ` [PATCH v3 1/8] dt-bindings: arm: qcom: Document MSM8939 SoC binding Bryan O'Donoghue
2023-01-17 2:48 ` [PATCH v3 2/8] dt-bindings: soc: qcom: smd-rpm: Exclude MSM8936 from glink-channels Bryan O'Donoghue
@ 2023-01-17 2:48 ` Bryan O'Donoghue
2023-01-17 11:04 ` Krzysztof Kozlowski
2023-01-17 2:48 ` [PATCH v3 4/8] clk: qcom: smd-rpm: msm8936: Add PMIC gated RPM_SMD_XO_* Bryan O'Donoghue
` (5 subsequent siblings)
8 siblings, 1 reply; 32+ messages in thread
From: Bryan O'Donoghue @ 2023-01-17 2:48 UTC (permalink / raw)
To: agross, andersson, konrad.dybcio, djakov, robh+dt,
krzysztof.kozlowski+dt
Cc: bryan.odonoghue, linux-arm-msm, linux-pm, devicetree,
linux-kernel, benl, shawn.guo, fabien.parent, leo.yan,
dmitry.baryshkov
New properties should be defined before the allOf. Move the
patternProperties definition to before the additionalProperties: false in
this file.
Exclude all non msm8939 compats from containing a matching
patternProperties.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
---
.../bindings/interconnect/qcom,rpm.yaml | 73 +++++++++++--------
1 file changed, 42 insertions(+), 31 deletions(-)
diff --git a/Documentation/devicetree/bindings/interconnect/qcom,rpm.yaml b/Documentation/devicetree/bindings/interconnect/qcom,rpm.yaml
index 5e6be4e79201e..d9d243c5514b5 100644
--- a/Documentation/devicetree/bindings/interconnect/qcom,rpm.yaml
+++ b/Documentation/devicetree/bindings/interconnect/qcom,rpm.yaml
@@ -62,6 +62,37 @@ properties:
power-domains:
maxItems: 1
+# Child node's properties
+patternProperties:
+ '^interconnect-[a-z0-9]+$':
+ type: object
+ description:
+ snoc-mm is a child of snoc, sharing snoc's register address space.
+
+ properties:
+ compatible:
+ enum:
+ - qcom,msm8939-snoc-mm
+
+ '#interconnect-cells':
+ const: 1
+
+ clock-names:
+ items:
+ - const: bus
+ - const: bus_a
+
+ clocks:
+ items:
+ - description: Bus Clock
+ - description: Bus A Clock
+
+ required:
+ - compatible
+ - '#interconnect-cells'
+ - clock-names
+ - clocks
+
required:
- compatible
- reg
@@ -108,37 +139,6 @@ allOf:
- description: Bus Clock
- description: Bus A Clock
- # Child node's properties
- patternProperties:
- '^interconnect-[a-z0-9]+$':
- type: object
- description:
- snoc-mm is a child of snoc, sharing snoc's register address space.
-
- properties:
- compatible:
- enum:
- - qcom,msm8939-snoc-mm
-
- '#interconnect-cells':
- const: 1
-
- clock-names:
- items:
- - const: bus
- - const: bus_a
-
- clocks:
- items:
- - description: Bus Clock
- - description: Bus A Clock
-
- required:
- - compatible
- - '#interconnect-cells'
- - clock-names
- - clocks
-
- if:
properties:
compatible:
@@ -237,6 +237,17 @@ allOf:
- description: Aggregate2 USB3 AXI Clock.
- description: Config NoC USB2 AXI Clock.
+ - if:
+ not:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - qcom,msm8939-snoc
+ then:
+ patternProperties:
+ '^interconnect-[a-z0-9]+$': false
+
examples:
- |
#include <dt-bindings/clock/qcom,rpmcc.h>
--
2.38.1
^ permalink raw reply related [flat|nested] 32+ messages in thread
* [PATCH v3 4/8] clk: qcom: smd-rpm: msm8936: Add PMIC gated RPM_SMD_XO_*
2023-01-17 2:48 [PATCH v3 0/8] Add MSM8939 SoC support with two devices Bryan O'Donoghue
` (2 preceding siblings ...)
2023-01-17 2:48 ` [PATCH v3 3/8] dt-bindings: interconnect: Exclude all non msm8939 from snoc-mm Bryan O'Donoghue
@ 2023-01-17 2:48 ` Bryan O'Donoghue
2023-01-18 13:49 ` Konrad Dybcio
2023-01-17 2:48 ` [PATCH v3 5/8] arm64: dts: qcom: Add msm8939 SoC Bryan O'Donoghue
` (4 subsequent siblings)
8 siblings, 1 reply; 32+ messages in thread
From: Bryan O'Donoghue @ 2023-01-17 2:48 UTC (permalink / raw)
To: agross, andersson, konrad.dybcio, djakov, robh+dt,
krzysztof.kozlowski+dt
Cc: bryan.odonoghue, linux-arm-msm, linux-pm, devicetree,
linux-kernel, benl, shawn.guo, fabien.parent, leo.yan,
dmitry.baryshkov
The XO crystal input is buffered through the PMIC and controlled by RPM.
Create the relevant clock gate representation in the RPM clock definitions.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
---
drivers/clk/qcom/clk-smd-rpm.c | 2 ++
1 file changed, 2 insertions(+)
diff --git a/drivers/clk/qcom/clk-smd-rpm.c b/drivers/clk/qcom/clk-smd-rpm.c
index 8f6e274c60301..6f23ca4828f44 100644
--- a/drivers/clk/qcom/clk-smd-rpm.c
+++ b/drivers/clk/qcom/clk-smd-rpm.c
@@ -574,6 +574,8 @@ static const struct rpm_smd_clk_desc rpm_clk_msm8916 = {
};
static struct clk_smd_rpm *msm8936_clks[] = {
+ [RPM_SMD_XO_CLK_SRC] = &clk_smd_rpm_branch_bi_tcxo,
+ [RPM_SMD_XO_A_CLK_SRC] = &clk_smd_rpm_branch_bi_tcxo_a,
[RPM_SMD_PCNOC_CLK] = &clk_smd_rpm_bus_0_pcnoc_clk,
[RPM_SMD_PCNOC_A_CLK] = &clk_smd_rpm_bus_0_pcnoc_a_clk,
[RPM_SMD_SNOC_CLK] = &clk_smd_rpm_bus_1_snoc_clk,
--
2.38.1
^ permalink raw reply related [flat|nested] 32+ messages in thread
* [PATCH v3 5/8] arm64: dts: qcom: Add msm8939 SoC
2023-01-17 2:48 [PATCH v3 0/8] Add MSM8939 SoC support with two devices Bryan O'Donoghue
` (3 preceding siblings ...)
2023-01-17 2:48 ` [PATCH v3 4/8] clk: qcom: smd-rpm: msm8936: Add PMIC gated RPM_SMD_XO_* Bryan O'Donoghue
@ 2023-01-17 2:48 ` Bryan O'Donoghue
2023-01-17 20:58 ` Bjorn Andersson
2023-01-18 9:59 ` Stephan Gerhold
2023-01-17 2:48 ` [PATCH v3 6/8] arm64: dts: qcom: Add msm8939-pm8916.dtsi include Bryan O'Donoghue
` (3 subsequent siblings)
8 siblings, 2 replies; 32+ messages in thread
From: Bryan O'Donoghue @ 2023-01-17 2:48 UTC (permalink / raw)
To: agross, andersson, konrad.dybcio, djakov, robh+dt,
krzysztof.kozlowski+dt
Cc: bryan.odonoghue, linux-arm-msm, linux-pm, devicetree,
linux-kernel, benl, shawn.guo, fabien.parent, leo.yan,
dmitry.baryshkov, Jun Nie, James Willcox, Joseph Gates, Max Chen,
Zac Crosby, Vincent Knecht, Stephan Gerhold
Add msm8939 a derivative SoC of msm8916. This SoC contains a number of key
differences to msm8916.
- big.LITTLE Octa Core - quad 1.5GHz + quad 1.0GHz
- DRAM 1x800 LPDDR3
- Camera 4+4 lane CSI
- Venus @ 1080p60 HEVC
- DSI x 2
- Adreno A405
- WiFi wcn3660/wcn3680b 802.11ac
Co-developed-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Co-developed-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Co-developed-by: Benjamin Li <benl@squareup.com>
Signed-off-by: Benjamin Li <benl@squareup.com>
Co-developed-by: James Willcox <jwillcox@squareup.com>
Signed-off-by: James Willcox <jwillcox@squareup.com>
Co-developed-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Co-developed-by: Joseph Gates <jgates@squareup.com>
Signed-off-by: Joseph Gates <jgates@squareup.com>
Co-developed-by: Max Chen <mchen@squareup.com>
Signed-off-by: Max Chen <mchen@squareup.com>
Co-developed-by: Zac Crosby <zac@squareup.com>
Signed-off-by: Zac Crosby <zac@squareup.com>
Co-developed-by: Vincent Knecht <vincent.knecht@mailoo.org>
Signed-off-by: Vincent Knecht <vincent.knecht@mailoo.org>
Co-developed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
---
arch/arm64/boot/dts/qcom/msm8939.dtsi | 2393 +++++++++++++++++++++++++
1 file changed, 2393 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/msm8939.dtsi
diff --git a/arch/arm64/boot/dts/qcom/msm8939.dtsi b/arch/arm64/boot/dts/qcom/msm8939.dtsi
new file mode 100644
index 0000000000000..8cd358a9fe623
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8939.dtsi
@@ -0,0 +1,2393 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) 2013-2015, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2020-2023, Linaro Limited
+ */
+
+#include <dt-bindings/clock/qcom,gcc-msm8939.h>
+#include <dt-bindings/clock/qcom,rpmcc.h>
+#include <dt-bindings/interconnect/qcom,msm8939.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/power/qcom-rpmpd.h>
+#include <dt-bindings/reset/qcom,gcc-msm8939.h>
+#include <dt-bindings/thermal/thermal.h>
+
+/ {
+ interrupt-parent = <&intc>;
+
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ clocks {
+ xo_board: xo-board {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <19200000>;
+ };
+
+ sleep_clk: sleep-clk {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ };
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu0: cpu@100 {
+ compatible = "arm,cortex-a53";
+ device_type = "cpu";
+ enable-method = "spin-table";
+ reg = <0x100>;
+ next-level-cache = <&L2_1>;
+ power-domains = <&vreg_dummy>;
+ power-domain-names = "cpr";
+ qcom,acc = <&acc0>;
+ qcom,saw = <&saw0>;
+ cpu-idle-states = <&CPU_SLEEP_0>;
+ clocks = <&apcs1_mbox>;
+ #cooling-cells = <2>;
+ L2_1: l2-cache {
+ compatible = "cache";
+ cache-level = <2>;
+ };
+ };
+
+ cpu1: cpu@101 {
+ compatible = "arm,cortex-a53";
+ device_type = "cpu";
+ enable-method = "spin-table";
+ reg = <0x101>;
+ next-level-cache = <&L2_1>;
+ power-domains = <&vreg_dummy>;
+ power-domain-names = "cpr";
+ qcom,acc = <&acc1>;
+ qcom,saw = <&saw1>;
+ cpu-idle-states = <&CPU_SLEEP_0>;
+ clocks = <&apcs1_mbox>;
+ #cooling-cells = <2>;
+ };
+
+ cpu2: cpu@102 {
+ compatible = "arm,cortex-a53";
+ device_type = "cpu";
+ enable-method = "spin-table";
+ reg = <0x102>;
+ next-level-cache = <&L2_1>;
+ power-domains = <&vreg_dummy>;
+ power-domain-names = "cpr";
+ qcom,acc = <&acc2>;
+ qcom,saw = <&saw2>;
+ cpu-idle-states = <&CPU_SLEEP_0>;
+ clocks = <&apcs1_mbox>;
+ #cooling-cells = <2>;
+ };
+
+ cpu3: cpu@103 {
+ compatible = "arm,cortex-a53";
+ device_type = "cpu";
+ enable-method = "spin-table";
+ reg = <0x103>;
+ next-level-cache = <&L2_1>;
+ power-domains = <&vreg_dummy>;
+ power-domain-names = "cpr";
+ qcom,acc = <&acc3>;
+ qcom,saw = <&saw3>;
+ cpu-idle-states = <&CPU_SLEEP_0>;
+ clocks = <&apcs1_mbox>;
+ #cooling-cells = <2>;
+ };
+
+ cpu4: cpu@0 {
+ compatible = "arm,cortex-a53";
+ device_type = "cpu";
+ enable-method = "spin-table";
+ reg = <0x0>;
+ qcom,acc = <&acc4>;
+ qcom,saw = <&saw4>;
+ cpu-idle-states = <&CPU_SLEEP_0>;
+ clocks = <&apcs0_mbox>;
+ #cooling-cells = <2>;
+ next-level-cache = <&L2_0>;
+ power-domains = <&vreg_dummy>;
+ power-domain-names = "cpr";
+ L2_0: l2-cache {
+ compatible = "cache";
+ cache-level = <2>;
+ };
+ };
+
+ cpu5: cpu@1 {
+ compatible = "arm,cortex-a53";
+ device_type = "cpu";
+ enable-method = "spin-table";
+ reg = <0x1>;
+ next-level-cache = <&L2_0>;
+ power-domains = <&vreg_dummy>;
+ power-domain-names = "cpr";
+ qcom,acc = <&acc5>;
+ qcom,saw = <&saw5>;
+ cpu-idle-states = <&CPU_SLEEP_0>;
+ clocks = <&apcs0_mbox>;
+ #cooling-cells = <2>;
+ };
+
+ cpu6: cpu@2 {
+ compatible = "arm,cortex-a53";
+ device_type = "cpu";
+ enable-method = "spin-table";
+ reg = <0x2>;
+ next-level-cache = <&L2_0>;
+ power-domains = <&vreg_dummy>;
+ power-domain-names = "cpr";
+ qcom,acc = <&acc6>;
+ qcom,saw = <&saw6>;
+ cpu-idle-states = <&CPU_SLEEP_0>;
+ clocks = <&apcs0_mbox>;
+ #cooling-cells = <2>;
+ };
+
+ cpu7: cpu@3 {
+ compatible = "arm,cortex-a53";
+ device_type = "cpu";
+ enable-method = "spin-table";
+ reg = <0x3>;
+ next-level-cache = <&L2_0>;
+ power-domains = <&vreg_dummy>;
+ power-domain-names = "cpr";
+ qcom,acc = <&acc7>;
+ qcom,saw = <&saw7>;
+ cpu-idle-states = <&CPU_SLEEP_0>;
+ clocks = <&apcs0_mbox>;
+ #cooling-cells = <2>;
+ };
+
+ idle-states {
+ CPU_SLEEP_0: cpu-sleep-0 {
+ compatible ="qcom,idle-state-spc", "arm,idle-state";
+ entry-latency-us = <130>;
+ exit-latency-us = <150>;
+ min-residency-us = <2000>;
+ local-timer-stop;
+ };
+ };
+ };
+
+ /*
+ * MSM8939 has a big.LITTLE heterogeneous computing architecture,
+ * consisting of two clusters of four ARM Cortex-A53s each. The
+ * LITTLE cluster runs at 1.0-1.2GHz, and the big cluster runs
+ * at 1.5-1.7GHz.
+ *
+ * The enable method used here is spin-table which presupposes use
+ * of a 2nd stage boot shim such as lk2nd to have installed a
+ * spin-table, the downstream non-psci/non-spin-table method that
+ * default msm8916/msm8936/msm8939 will not be supported upstream.
+ */
+ cpu-map {
+ /* LITTLE (efficiency) cluster */
+ cluster0 {
+ core0 {
+ cpu = <&cpu4>;
+ };
+
+ core1 {
+ cpu = <&cpu5>;
+ };
+
+ core2 {
+ cpu = <&cpu6>;
+ };
+
+ core3 {
+ cpu = <&cpu7>;
+ };
+ };
+
+ /* big (performance) cluster */
+ /* Boot CPU is cluster 1 core 0 */
+ cluster1 {
+ core0 {
+ cpu = <&cpu0>;
+ };
+
+ core1 {
+ cpu = <&cpu1>;
+ };
+
+ core2 {
+ cpu = <&cpu2>;
+ };
+
+ core3 {
+ cpu = <&cpu3>;
+ };
+ };
+ };
+
+ firmware {
+ scm: scm {
+ compatible = "qcom,scm-msm8916", "qcom,scm";
+ clocks = <&gcc GCC_CRYPTO_CLK>,
+ <&gcc GCC_CRYPTO_AXI_CLK>,
+ <&gcc GCC_CRYPTO_AHB_CLK>;
+ clock-names = "core", "bus", "iface";
+ #reset-cells = <1>;
+
+ qcom,dload-mode = <&tcsr 0x6100>;
+ };
+ };
+
+ smp2p-hexagon {
+ compatible = "qcom,smp2p";
+ qcom,smem = <435>, <428>;
+
+ interrupts = <GIC_SPI 27 IRQ_TYPE_EDGE_RISING>;
+
+ mboxes = <&apcs1_mbox 14>;
+
+ qcom,local-pid = <0>;
+ qcom,remote-pid = <1>;
+
+ hexagon_smp2p_out: master-kernel {
+ qcom,entry-name = "master-kernel";
+
+ #qcom,smem-state-cells = <1>;
+ };
+
+ hexagon_smp2p_in: slave-kernel {
+ qcom,entry-name = "slave-kernel";
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ #address-cells = <0>;
+ #size-cells = <0>;
+ };
+ };
+
+ memory@80000000 {
+ device_type = "memory";
+ /* We expect the bootloader to fill in the reg */
+ reg = <0x0 0x80000000 0x0 0x0>;
+ };
+
+ pmu {
+ compatible = "arm,cortex-a53-pmu";
+ interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_HIGH)>;
+ };
+
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ tz-apps@86000000 {
+ reg = <0x0 0x86000000 0x0 0x300000>;
+ no-map;
+ };
+
+ smem@86300000 {
+ compatible = "qcom,smem";
+ reg = <0x0 0x86300000 0x0 0x100000>;
+ no-map;
+
+ hwlocks = <&tcsr_mutex 3>;
+ qcom,rpm-msg-ram = <&rpm_msg_ram>;
+ };
+
+ hypervisor@86400000 {
+ reg = <0x0 0x86400000 0x0 0x100000>;
+ no-map;
+ };
+
+ tz@86500000 {
+ reg = <0x0 0x86500000 0x0 0x180000>;
+ no-map;
+ };
+
+ reserved@86680000 {
+ reg = <0x0 0x86680000 0x0 0x80000>;
+ no-map;
+ };
+
+ rmtfs@86700000 {
+ compatible = "qcom,rmtfs-mem";
+ reg = <0x0 0x86700000 0x0 0xe0000>;
+ no-map;
+
+ qcom,client-id = <1>;
+ };
+
+ rfsa@867e0000 {
+ reg = <0x0 0x867e0000 0x0 0x20000>;
+ no-map;
+ };
+
+ mpss_mem: mpss@86800000 {
+ reg = <0x0 0x86800000 0x0 0x5500000>;
+ no-map;
+ };
+
+ wcnss_mem: wcnss@8bd00000 {
+ reg = <0x0 0x8bd00000 0x0 0x600000>;
+ no-map;
+ };
+
+ venus_mem: venus@8c300000 {
+ reg = <0x0 0x8c300000 0x0 0x800000>;
+ no-map;
+ };
+
+ mba_mem: mba@8cb00000 {
+ no-map;
+ reg = <0x0 0x8cb00000 0x0 0x100000>;
+ };
+ };
+
+ smsm {
+ compatible = "qcom,smsm";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ qcom,ipc-1 = <&apcs1_mbox 8 13>;
+ qcom,ipc-3 = <&apcs1_mbox 8 19>;
+
+ apps_smsm: apps@0 {
+ reg = <0>;
+
+ #qcom,smem-state-cells = <1>;
+ };
+
+ hexagon_smsm: hexagon@1 {
+ reg = <1>;
+ interrupts = <GIC_SPI 26 IRQ_TYPE_EDGE_RISING>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ wcnss_smsm: wcnss@6 {
+ reg = <6>;
+ interrupts = <GIC_SPI 144 IRQ_TYPE_EDGE_RISING>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
+ soc: soc@0 {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0 0 0xffffffff>;
+
+ rng@22000 {
+ compatible = "qcom,prng";
+ reg = <0x00022000 0x200>;
+ clocks = <&gcc GCC_PRNG_AHB_CLK>;
+ clock-names = "core";
+ };
+
+ qfprom: qfprom@5c000 {
+ compatible = "qcom,msm8916-qfprom", "qcom,qfprom";
+ reg = <0x0005c000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ tsens_caldata: caldata@a0 {
+ reg = <0xa0 0x5c>;
+ };
+ cpr_efuse_init_voltage1: ivoltage1@dc {
+ reg = <0xdc 0x4>;
+ bits = <4 6>;
+ };
+ cpr_efuse_init_voltage2: ivoltage2@da {
+ reg = <0xda 0x4>;
+ bits = <2 6>;
+ };
+ cpr_efuse_init_voltage3: ivoltage3@d8 {
+ reg = <0xd8 0x4>;
+ bits = <0 6>;
+ };
+ cpr_efuse_quot1: quot1@dd {
+ reg = <0xdd 0x8>;
+ bits = <2 12>;
+ };
+ cpr_efuse_quot2: quot2@db {
+ reg = <0xdb 0x8>;
+ bits = <0x0 12>;
+ };
+ cpr_efuse_ring1: ring1@de {
+ reg = <0xde 0x4>;
+ bits = <6 3>;
+ };
+ cpr_efuse_revision: revision@5 {
+ reg = <0x5 0x1>;
+ bits = <5 1>;
+ };
+ cpr_efuse_revision_high: revision-high@7 {
+ reg = <0x7 0x1>;
+ bits = <0 1>;
+ };
+ cpr_efuse_pvs_version: pvs@3 {
+ reg = <0x3 0x1>;
+ bits = <5 1>;
+ };
+ cpr_efuse_pvs_version_high: pvs-high@6 {
+ reg = <0x6 0x1>;
+ bits = <2 2>;
+ };
+ cpr_efuse_speedbin: speedbin@c {
+ reg = <0xc 0x1>;
+ bits = <2 3>;
+ };
+ };
+
+ rpm_msg_ram: sram@60000 {
+ compatible = "qcom,rpm-msg-ram";
+ reg = <0x00060000 0x8000>;
+ };
+
+ bimc: interconnect@400000 {
+ compatible = "qcom,msm8939-bimc";
+ reg = <0x00400000 0x62000>;
+ clock-names = "bus", "bus_a";
+ clocks = <&rpmcc RPM_SMD_BIMC_CLK>,
+ <&rpmcc RPM_SMD_BIMC_A_CLK>;
+ #interconnect-cells = <1>;
+ };
+
+ tsens: thermal-sensor@4a9000 {
+ compatible = "qcom,msm8939-tsens", "qcom,tsens-v0_1";
+ reg = <0x004a9000 0x1000>, /* TM */
+ <0x004a8000 0x1000>; /* SROT */
+ nvmem-cells = <&tsens_caldata>;
+ nvmem-cell-names = "calib";
+ #qcom,sensors = <10>;
+ interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "uplow";
+ #thermal-sensor-cells = <1>;
+ };
+
+ restart@4ab000 {
+ compatible = "qcom,pshold";
+ reg = <0x004ab000 0x4>;
+ };
+
+ pcnoc: interconnect@500000 {
+ compatible = "qcom,msm8939-pcnoc";
+ reg = <0x00500000 0x11000>;
+ clock-names = "bus", "bus_a";
+ clocks = <&rpmcc RPM_SMD_PCNOC_CLK>,
+ <&rpmcc RPM_SMD_PCNOC_A_CLK>;
+ #interconnect-cells = <1>;
+ };
+
+ snoc: interconnect@580000 {
+ compatible = "qcom,msm8939-snoc";
+ reg = <0x00580000 0x14080>;
+ clock-names = "bus", "bus_a";
+ clocks = <&rpmcc RPM_SMD_SNOC_CLK>,
+ <&rpmcc RPM_SMD_SNOC_A_CLK>;
+ #interconnect-cells = <1>;
+
+ snoc_mm: interconnect-snoc {
+ compatible = "qcom,msm8939-snoc-mm";
+ clock-names = "bus", "bus_a";
+ clocks = <&rpmcc RPM_SMD_SYSMMNOC_CLK>,
+ <&rpmcc RPM_SMD_SYSMMNOC_A_CLK>;
+ #interconnect-cells = <1>;
+ };
+ };
+
+ tlmm: pinctrl@1000000 {
+ compatible = "qcom,msm8916-pinctrl";
+ reg = <0x01000000 0x300000>;
+ interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ gpio-ranges = <&tlmm 0 0 122>;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ blsp1_uart1_default: blsp1-uart1-default-state {
+ pins = "gpio0", "gpio1", "gpio2", "gpio3";
+ function = "blsp_uart1";
+ drive-strength = <16>;
+ bias-disable;
+ };
+
+ blsp1_uart1_sleep: blsp1-uart1-sleep-state {
+ pins = "gpio0", "gpio1", "gpio2", "gpio3";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ blsp1_uart2_default: blsp1-uart2-default-state {
+ pins = "gpio4", "gpio5";
+ function = "blsp_uart2";
+ drive-strength = <16>;
+ bias-disable;
+ };
+
+ blsp1_uart2_sleep: blsp1-uart2-sleep-state {
+ pins = "gpio4", "gpio5";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ camera_front_default: camera-front-default-state {
+ pwdn-pins {
+ pins = "gpio33";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ };
+
+ rst-pins {
+ pins = "gpio28";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ };
+
+ mclk1-pins {
+ pins = "gpio27";
+ function = "cam_mclk1";
+ drive-strength = <16>;
+ bias-disable;
+ };
+ };
+
+ camera_rear_default: camera-rear-default-state {
+ pwdn-pins {
+ pins = "gpio34";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ };
+
+ rst-pins {
+ pins = "gpio35";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ };
+
+ mclk0-pins {
+ pins = "gpio26";
+ function = "cam_mclk0";
+ drive-strength = <16>;
+ bias-disable;
+ };
+ };
+
+ cci0_default: cci0-default-state {
+ pins = "gpio29", "gpio30";
+ function = "cci_i2c";
+ drive-strength = <16>;
+ bias-disable;
+ };
+
+ cdc_pdm_lines_default: pdm-lines-default-state {
+ pins = "gpio63", "gpio64", "gpio65", "gpio66",
+ "gpio67", "gpio68";
+ function = "cdc_pdm0";
+ drive-strength = <8>;
+ bias-disable;
+ };
+
+ cdc_pdm_lines_sleep: pdm-lines-suspend-state {
+ pins = "gpio63", "gpio64", "gpio65", "gpio66",
+ "gpio67", "gpio68";
+ function = "cdc_pdm0";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ cdc_dmic_lines_act: cdc-dmic-lines-on-state {
+ clk-pins {
+ pins = "gpio0";
+ function = "dmic0_clk";
+ drive-strength = <8>;
+ };
+
+ data-pins {
+ pins = "gpio1";
+ function = "dmic0_data";
+ drive-strength = <8>;
+ };
+ };
+
+ cdc_dmic_lines_sus: cdc-dmic-lines-off-state {
+ clk-pins {
+ pins = "gpio0";
+ function = "dmic0_clk";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ data-pins {
+ pins = "gpio1";
+ function = "dmic0_data";
+ drive-strength = <2>;
+ bias-disable;
+ };
+ };
+
+ ext-mclk-tlmm-lines-state {
+ ext_mclk_tlmm_lines_act: mclk-lines-on-pins {
+ pins = "gpio116";
+ function = "pri_mi2s";
+ drive-strength = <8>;
+ bias-disable;
+ };
+
+ ext_mclk_tlmm_lines_sus: mclk-lines-off-pins {
+ pins = "gpio116";
+ function = "pri_mi2s";
+ drive-strength = <2>;
+ bias-disable;
+ };
+ };
+
+ ext-pri-tlmm-lines-state {
+ ext_pri_tlmm_lines_act: ext-pa-on-pins {
+ pins = "gpio113", "gpio114", "gpio115", "gpio116";
+ function = "pri_mi2s";
+ drive-strength = <8>;
+ bias-disable;
+ };
+
+ ext_pri_tlmm_lines_sus: ext-pa-off-pins {
+ pins = "gpio113", "gpio114", "gpio115", "gpio116";
+ function = "pri_mi2s";
+ drive-strength = <2>;
+ bias-disable;
+ };
+ };
+
+ ext-pri-ws-line-state {
+ ext_pri_ws_act: ext-pa-on-pins {
+ pins = "gpio110";
+ function = "pri_mi2s_ws";
+ drive-strength = <8>;
+ bias-disable;
+ };
+
+ ext_pri_ws_sus: ext-pa-off-pins {
+ pins = "gpio110";
+ function = "pri_mi2s_ws";
+ drive-strength = <2>;
+ bias-disable;
+ };
+ };
+
+ /* secondary Mi2S */
+ ext-sec-tlmm-lines-state {
+ ext_sec_tlmm_lines_act: tlmm-lines-on-pins {
+ pins = "gpio112", "gpio117", "gpio118", "gpio119";
+ function = "sec_mi2s";
+ drive-strength = <8>;
+ bias-disable;
+ };
+
+ ext_sec_tlmm_lines_sus: tlmm-lines-off-pins {
+ pins = "gpio112", "gpio117", "gpio118", "gpio119";
+ function = "sec_mi2s";
+ drive-strength = <2>;
+ bias-disable;
+ };
+ };
+
+ i2c1_default: i2c1-default-state {
+ pins = "gpio2", "gpio3";
+ function = "blsp_i2c1";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ i2c1_sleep: i2c1-sleep-state {
+ pins = "gpio2", "gpio3";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ i2c2_default: i2c2-default-state {
+ pins = "gpio6", "gpio7";
+ function = "blsp_i2c2";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ i2c2_sleep: i2c2-sleep-state {
+ pins = "gpio6", "gpio7";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ i2c3_default: i2c3-default-state {
+ pins = "gpio10", "gpio11";
+ function = "blsp_i2c3";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ i2c3_sleep: i2c3-sleep-state {
+ pins = "gpio10", "gpio11";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ i2c4_default: i2c4-default-state {
+ pins = "gpio14", "gpio15";
+ function = "blsp_i2c4";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ i2c4_sleep: i2c4-sleep-state {
+ pins = "gpio14", "gpio15";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ i2c5_default: i2c5-default-state {
+ pins = "gpio18", "gpio19";
+ function = "blsp_i2c5";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ i2c5_sleep: i2c5-sleep-state {
+ pins = "gpio18", "gpio19";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ i2c6_default: i2c6-default-state {
+ pins = "gpio22", "gpio23";
+ function = "blsp_i2c6";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ i2c6_sleep: i2c6-sleep-state {
+ pins = "gpio22", "gpio23";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ sdc1_default_state: sdc1-default-state {
+ clk-pins {
+ pins = "sdc1_clk";
+ bias-disable;
+ drive-strength = <16>;
+ };
+
+ cmd-pins {
+ pins = "sdc1_cmd";
+ bias-pull-up;
+ drive-strength = <10>;
+ };
+
+ data-pins {
+ pins = "sdc1_data";
+ bias-pull-up;
+ drive-strength = <10>;
+ };
+ };
+
+ sdc1_sleep_state: sdc1-sleep-state {
+ clk-pins {
+ pins = "sdc1_clk";
+ bias-disable;
+ drive-strength = <2>;
+ };
+
+ cmd-pins {
+ pins = "sdc1_cmd";
+ bias-pull-up;
+ drive-strength = <2>;
+ };
+
+ data-pins {
+ pins = "sdc1_data";
+ bias-pull-up;
+ drive-strength = <2>;
+ };
+ };
+
+ sdc2_default_state: sdc2-default-state {
+ clk-pins {
+ pins = "sdc2_clk";
+ bias-disable;
+ drive-strength = <16>;
+ };
+
+ cmd-pins {
+ pins = "sdc2_cmd";
+ bias-pull-up;
+ drive-strength = <10>;
+ };
+
+ data-pins {
+ pins = "sdc2_data";
+ bias-pull-up;
+ drive-strength = <10>;
+ };
+
+ cd-pins {
+ pins = "gpio38";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ sdc2_sleep_state: sdc2-sleep-state {
+ clk-pins {
+ pins = "sdc2_clk";
+ bias-disable;
+ drive-strength = <2>;
+ };
+
+ cmd-pins {
+ pins = "sdc2_cmd";
+ bias-pull-up;
+ drive-strength = <2>;
+ };
+
+ data-pins {
+ pins = "sdc2_data";
+ bias-pull-up;
+ drive-strength = <2>;
+ };
+
+ cd-pins {
+ pins = "gpio38";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+ };
+
+ spi1_default: spi1-default-state {
+ spi-pins {
+ pins = "gpio0", "gpio1", "gpio3";
+ function = "blsp_spi1";
+ drive-strength = <12>;
+ bias-disable;
+ };
+
+ cs-pins {
+ pins = "gpio2";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ output-high;
+ };
+ };
+
+ spi1_sleep: spi1-sleep-state {
+ pins = "gpio0", "gpio1", "gpio2", "gpio3";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ spi2_default: spi2-default-state {
+ spi-pins {
+ pins = "gpio4", "gpio5", "gpio7";
+ function = "blsp_spi2";
+ drive-strength = <12>;
+ bias-disable;
+ };
+
+ cs-pins {
+ pins = "gpio6";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ output-high;
+ };
+ };
+
+ spi2_sleep: spi2-sleep-state {
+ pins = "gpio4", "gpio5", "gpio6", "gpio7";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ spi3_default: spi3-default-state {
+ spi-pins {
+ pins = "gpio8", "gpio9", "gpio11";
+ function = "blsp_spi3";
+ drive-strength = <12>;
+ bias-disable;
+ };
+
+ cs-pins {
+ pins = "gpio10";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ output-high;
+ };
+ };
+
+ spi3_sleep: spi3-sleep-state {
+ pins = "gpio8", "gpio9", "gpio10", "gpio11";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ spi4_default: spi4-default-state {
+ spi-pins {
+ pins = "gpio12", "gpio13", "gpio15";
+ function = "blsp_spi4";
+ drive-strength = <12>;
+ bias-disable;
+ };
+
+ cs-pins {
+ pins = "gpio14";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ output-high;
+ };
+ };
+
+ spi4_sleep: spi4-sleep-state {
+ pins = "gpio12", "gpio13", "gpio14", "gpio15";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ spi5_default: spi5-default-state {
+ spi-pins {
+ pins = "gpio16", "gpio17", "gpio19";
+ function = "blsp_spi5";
+ drive-strength = <12>;
+ bias-disable;
+ };
+
+ cs-pins {
+ pins = "gpio18";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ output-high;
+ };
+ };
+
+ spi5_sleep: spi5-sleep-state {
+ pins = "gpio16", "gpio17", "gpio18", "gpio19";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ spi6_default: spi6-default-state {
+ spi-pins {
+ pins = "gpio20", "gpio21", "gpio23";
+ function = "blsp_spi6";
+ drive-strength = <12>;
+ bias-disable;
+ };
+
+ cs-pins {
+ pins = "gpio22";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ output-high;
+ };
+ };
+
+ spi6_sleep: spi6-sleep-state {
+ pins = "gpio20", "gpio21", "gpio22", "gpio23";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ wcnss_pin_a: wcnss-active-state {
+ pins = "gpio40", "gpio41", "gpio42", "gpio43", "gpio44";
+ function = "wcss_wlan";
+ drive-strength = <6>;
+ bias-pull-up;
+ };
+ };
+
+ gcc: clock-controller@1800000 {
+ compatible = "qcom,gcc-msm8939";
+ reg = <0x01800000 0x80000>;
+ clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>,
+ <&sleep_clk>,
+ <&dsi_phy0 1>,
+ <&dsi_phy0 0>,
+ <0>,
+ <0>,
+ <0>;
+ clock-names = "xo",
+ "sleep_clk",
+ "dsi0pll",
+ "dsi0pllbyte",
+ "ext_mclk",
+ "ext_pri_i2s",
+ "ext_sec_i2s";
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ #power-domain-cells = <1>;
+ };
+
+ tcsr_mutex: hwlock@1905000 {
+ compatible = "qcom,tcsr-mutex";
+ reg = <0x01905000 0x20000>;
+ #hwlock-cells = <1>;
+ };
+
+ tcsr: syscon@1937000 {
+ compatible = "qcom,tcsr-msm8916", "syscon";
+ reg = <0x01937000 0x30000>;
+ };
+
+ mdss: display-subsystem@1a00000 {
+ compatible = "qcom,mdss";
+ reg = <0x01a00000 0x1000>,
+ <0x01ac8000 0x3000>;
+ reg-names = "mdss_phys", "vbif_phys";
+
+ interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+
+ clocks = <&gcc GCC_MDSS_AHB_CLK>,
+ <&gcc GCC_MDSS_AXI_CLK>,
+ <&gcc GCC_MDSS_VSYNC_CLK>;
+ clock-names = "iface",
+ "bus",
+ "vsync";
+
+ power-domains = <&gcc MDSS_GDSC>;
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+ #interrupt-cells = <1>;
+ ranges;
+
+ mdp: display-controller@1a01000 {
+ compatible = "qcom,mdp5";
+ reg = <0x01a01000 0x89000>;
+ reg-names = "mdp_phys";
+
+ interrupt-parent = <&mdss>;
+ interrupts = <0>;
+
+ clocks = <&gcc GCC_MDSS_AHB_CLK>,
+ <&gcc GCC_MDSS_AXI_CLK>,
+ <&gcc GCC_MDSS_MDP_CLK>,
+ <&gcc GCC_MDSS_VSYNC_CLK>,
+ <&gcc GCC_MDP_TBU_CLK>,
+ <&gcc GCC_MDP_RT_TBU_CLK>;
+ clock-names = "iface",
+ "bus",
+ "core",
+ "vsync",
+ "tbu",
+ "tbu_rt";
+
+ iommus = <&apps_iommu 4>;
+
+ interconnects = <&snoc_mm MASTER_MDP_PORT0 &bimc SLAVE_EBI_CH0>,
+ <&snoc_mm MASTER_MDP_PORT1 &bimc SLAVE_EBI_CH0>,
+ <&pcnoc MASTER_SPDM &snoc SLAVE_IMEM>;
+ interconnect-names = "mdp0-mem", "mdp1-mem", "register-mem";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ mdp5_intf1_out: endpoint {
+ remote-endpoint = <&dsi0_in>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ mdp5_intf2_out: endpoint {
+ remote-endpoint = <&dsi1_in>;
+ };
+ };
+ };
+ };
+
+ dsi0: dsi@1a98000 {
+ compatible = "qcom,msm8916-dsi-ctrl",
+ "qcom,mdss-dsi-ctrl";
+ reg = <0x01a98000 0x25c>;
+ reg-names = "dsi_ctrl";
+
+ interrupt-parent = <&mdss>;
+ interrupts = <4>;
+
+ power-domains = <&gcc MDSS_GDSC>;
+
+ clocks = <&gcc GCC_MDSS_MDP_CLK>,
+ <&gcc GCC_MDSS_AHB_CLK>,
+ <&gcc GCC_MDSS_AXI_CLK>,
+ <&gcc GCC_MDSS_BYTE0_CLK>,
+ <&gcc GCC_MDSS_PCLK0_CLK>,
+ <&gcc GCC_MDSS_ESC0_CLK>;
+ clock-names = "mdp_core",
+ "iface",
+ "bus",
+ "byte",
+ "pixel",
+ "core";
+ assigned-clocks = <&gcc BYTE0_CLK_SRC>,
+ <&gcc PCLK0_CLK_SRC>;
+ assigned-clock-parents = <&dsi_phy0 0>,
+ <&dsi_phy0 1>;
+
+ phys = <&dsi_phy0>;
+ status = "disabled";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ dsi0_in: endpoint {
+ remote-endpoint = <&mdp5_intf1_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ dsi0_out: endpoint {
+ };
+ };
+ };
+ };
+
+ dsi_phy0: phy@1a98300 {
+ compatible = "qcom,dsi-phy-28nm-lp";
+ reg = <0x01a98300 0xd4>,
+ <0x01a98500 0x280>,
+ <0x01a98780 0x30>;
+ reg-names = "dsi_pll",
+ "dsi_phy",
+ "dsi_phy_regulator";
+
+ clocks = <&gcc GCC_MDSS_AHB_CLK>,
+ <&rpmcc RPM_SMD_XO_CLK_SRC>;
+ clock-names = "iface", "ref";
+
+ #clock-cells = <1>;
+ #phy-cells = <0>;
+ status = "disabled";
+ };
+
+ dsi1: dsi@1aa0000 {
+ compatible = "qcom,msm8916-dsi-ctrl",
+ "qcom,mdss-dsi-ctrl";
+ reg = <0x01aa0000 0x25c>;
+ reg-names = "dsi_ctrl";
+
+ interrupt-parent = <&mdss>;
+ interrupts = <5>;
+
+ power-domains = <&gcc MDSS_GDSC>;
+
+ clocks = <&gcc GCC_MDSS_MDP_CLK>,
+ <&gcc GCC_MDSS_AHB_CLK>,
+ <&gcc GCC_MDSS_AXI_CLK>,
+ <&gcc GCC_MDSS_BYTE1_CLK>,
+ <&gcc GCC_MDSS_PCLK1_CLK>,
+ <&gcc GCC_MDSS_ESC1_CLK>;
+ clock-names = "mdp_core",
+ "iface",
+ "bus",
+ "byte",
+ "pixel",
+ "core";
+ assigned-clocks = <&gcc BYTE1_CLK_SRC>,
+ <&gcc PCLK1_CLK_SRC>;
+ assigned-clock-parents = <&dsi_phy1 0>,
+ <&dsi_phy1 1>;
+ phys = <&dsi_phy1>;
+ status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ dsi1_in: endpoint {
+ remote-endpoint = <&mdp5_intf2_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ dsi1_out: endpoint {
+ };
+ };
+ };
+ };
+
+ dsi_phy1: phy@1aa0300 {
+ compatible = "qcom,dsi-phy-28nm-lp";
+ reg = <0x01aa0300 0xd4>,
+ <0x01aa0500 0x280>,
+ <0x01aa0780 0x30>;
+ reg-names = "dsi_pll",
+ "dsi_phy",
+ "dsi_phy_regulator";
+
+ clocks = <&gcc GCC_MDSS_AHB_CLK>,
+ <&rpmcc RPM_SMD_XO_CLK_SRC>;
+ clock-names = "iface", "ref";
+
+ #clock-cells = <1>;
+ #phy-cells = <0>;
+ status = "disabled";
+ };
+ };
+
+ gpu@1c00000 {
+ compatible = "qcom,adreno-405.0", "qcom,adreno";
+ reg = <0x01c00000 0x10000>;
+ reg-names = "kgsl_3d0_reg_memory";
+ interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "kgsl_3d0_irq";
+ clock-names = "core",
+ "iface",
+ "mem",
+ "mem_iface",
+ "alt_mem_iface",
+ "gfx3d",
+ "rbbmtimer";
+ clocks = <&gcc GCC_OXILI_GFX3D_CLK>,
+ <&gcc GCC_OXILI_AHB_CLK>,
+ <&gcc GCC_OXILI_GMEM_CLK>,
+ <&gcc GCC_BIMC_GFX_CLK>,
+ <&gcc GCC_BIMC_GPU_CLK>,
+ <&gcc GFX3D_CLK_SRC>,
+ <&gcc GCC_OXILI_TIMER_CLK>;
+ power-domains = <&gcc OXILI_GDSC>;
+ operating-points-v2 = <&opp_table>;
+ iommus = <&gpu_iommu 1>, <&gpu_iommu 2>;
+
+ opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ opp-550000000 {
+ opp-hz = /bits/ 64 <550000000>;
+ };
+
+ opp-465000000 {
+ opp-hz = /bits/ 64 <465000000>;
+ };
+
+ opp-400000000 {
+ opp-hz = /bits/ 64 <400000000>;
+ };
+
+ opp-220000000 {
+ opp-hz = /bits/ 64 <220000000>;
+ };
+
+ opp-19200000 {
+ opp-hz = /bits/ 64 <19200000>;
+ };
+ };
+ };
+
+ apps_iommu: iommu@1ef0000 {
+ compatible = "qcom,msm8916-iommu", "qcom,msm-iommu-v1";
+ reg = <0x01ef0000 0x3000>;
+ ranges = <0 0x1e20000 0x40000>;
+ clocks = <&gcc GCC_SMMU_CFG_CLK>,
+ <&gcc GCC_APSS_TCU_CLK>;
+ clock-names = "iface", "bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ #iommu-cells = <1>;
+ qcom,iommu-secure-id = <17>;
+
+ /* mdp_0: */
+ iommu-ctx@4000 {
+ compatible = "qcom,msm-iommu-v1-ns";
+ reg = <0x4000 0x1000>;
+ interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ /* venus_ns: */
+ iommu-ctx@5000 {
+ compatible = "qcom,msm-iommu-v1-sec";
+ reg = <0x5000 0x1000>;
+ interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
+ };
+ };
+
+ gpu_iommu: iommu@1f08000 {
+ compatible = "qcom,msm8916-iommu", "qcom,msm-iommu-v1";
+ ranges = <0 0x1f08000 0x10000>;
+ clocks = <&gcc GCC_SMMU_CFG_CLK>,
+ <&gcc GCC_GFX_TCU_CLK>,
+ <&gcc GCC_GFX_TBU_CLK>;
+ clock-names = "iface", "bus", "tbu";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ #iommu-cells = <1>;
+ qcom,iommu-secure-id = <18>;
+
+ /* gfx3d_user: */
+ iommu-ctx@1000 {
+ compatible = "qcom,msm-iommu-v1-ns";
+ reg = <0x1000 0x1000>;
+ interrupts = <GIC_SPI 241 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ /* gfx3d_priv: */
+ iommu-ctx@2000 {
+ compatible = "qcom,msm-iommu-v1-ns";
+ reg = <0x2000 0x1000>;
+ interrupts = <GIC_SPI 242 IRQ_TYPE_LEVEL_HIGH>;
+ };
+ };
+
+ spmi_bus: spmi@200f000 {
+ compatible = "qcom,spmi-pmic-arb";
+ reg = <0x0200f000 0x001000>,
+ <0x02400000 0x400000>,
+ <0x02c00000 0x400000>,
+ <0x03800000 0x200000>,
+ <0x0200a000 0x002100>;
+ reg-names = "core", "chnls", "obsrvr", "intr", "cnfg";
+ interrupt-names = "periph_irq";
+ interrupts = <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>;
+ qcom,ee = <0>;
+ qcom,channel = <0>;
+ #address-cells = <2>;
+ #size-cells = <0>;
+ interrupt-controller;
+ #interrupt-cells = <4>;
+ };
+
+ mpss: remoteproc@4080000 {
+ compatible = "qcom,msm8916-mss-pil";
+ reg = <0x04080000 0x100>,
+ <0x04020000 0x040>;
+
+ reg-names = "qdsp6", "rmb";
+
+ interrupts-extended = <&intc GIC_SPI 24 IRQ_TYPE_EDGE_RISING>,
+ <&hexagon_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
+ <&hexagon_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
+ <&hexagon_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
+ <&hexagon_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
+ interrupt-names = "wdog", "fatal", "ready",
+ "handover", "stop-ack";
+
+ clocks = <&gcc GCC_MSS_CFG_AHB_CLK>,
+ <&gcc GCC_MSS_Q6_BIMC_AXI_CLK>,
+ <&gcc GCC_BOOT_ROM_AHB_CLK>,
+ <&rpmcc RPM_SMD_XO_CLK_SRC>;
+ clock-names = "iface", "bus", "mem", "xo";
+
+ power-domains = <&rpmpd MSM8939_VDDMDCX>,
+ <&rpmpd MSM8939_VDDMX>;
+ power-domain-names = "cx", "mx";
+
+ qcom,smem-states = <&hexagon_smp2p_out 0>;
+ qcom,smem-state-names = "stop";
+
+ resets = <&scm 0>;
+ reset-names = "mss_restart";
+
+ qcom,halt-regs = <&tcsr 0x18000 0x19000 0x1a000>;
+
+ status = "disabled";
+
+ mba {
+ memory-region = <&mba_mem>;
+ };
+
+ mpss {
+ memory-region = <&mpss_mem>;
+ };
+
+ smd-edge {
+ interrupts = <GIC_SPI 25 IRQ_TYPE_EDGE_RISING>;
+
+ qcom,smd-edge = <0>;
+ mboxes = <&apcs1_mbox 12>;
+ qcom,remote-pid = <1>;
+
+ label = "hexagon";
+ };
+ };
+
+ sound: sound@7702000 {
+ compatible = "qcom,apq8016-sbc-sndcard";
+ reg = <0x07702000 0x4>,
+ <0x07702004 0x4>;
+ reg-names = "mic-iomux", "spkr-iomux";
+ status = "disabled";
+ };
+
+ lpass: audio-controller@7708000 {
+ compatible = "qcom,apq8016-lpass-cpu";
+ reg = <0x07708000 0x10000>;
+ reg-names = "lpass-lpaif";
+ interrupts = <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "lpass-irq-lpaif";
+ clocks = <&gcc GCC_ULTAUDIO_AHBFABRIC_IXFABRIC_CLK>,
+ <&gcc GCC_ULTAUDIO_LPAIF_PRI_I2S_CLK>,
+ <&gcc GCC_ULTAUDIO_LPAIF_PRI_I2S_CLK>,
+ <&gcc GCC_ULTAUDIO_LPAIF_SEC_I2S_CLK>,
+ <&gcc GCC_ULTAUDIO_LPAIF_AUX_I2S_CLK>,
+ <&gcc GCC_ULTAUDIO_PCNOC_MPORT_CLK>,
+ <&gcc GCC_ULTAUDIO_PCNOC_SWAY_CLK>;
+ clock-names = "ahbix-clk",
+ "mi2s-bit-clk0",
+ "mi2s-bit-clk1",
+ "mi2s-bit-clk2",
+ "mi2s-bit-clk3",
+ "pcnoc-mport-clk",
+ "pcnoc-sway-clk";
+ #sound-dai-cells = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ lpass_codec: audio-codec@771c000 {
+ compatible = "qcom,msm8916-wcd-digital-codec";
+ reg = <0x0771c000 0x400>;
+ clocks = <&gcc GCC_ULTAUDIO_AHBFABRIC_IXFABRIC_CLK>,
+ <&gcc GCC_CODEC_DIGCODEC_CLK>;
+ clock-names = "ahbix-clk", "mclk";
+ #sound-dai-cells = <1>;
+ };
+
+ sdhc_1: mmc@7824900 {
+ compatible = "qcom,msm8916-sdhci", "qcom,sdhci-msm-v4";
+ reg = <0x07824900 0x11c>, <0x07824000 0x800>;
+ reg-names = "hc", "core";
+
+ interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "hc_irq", "pwr_irq";
+ clocks = <&gcc GCC_SDCC1_AHB_CLK>,
+ <&gcc GCC_SDCC1_APPS_CLK>,
+ <&rpmcc RPM_SMD_XO_CLK_SRC>;
+ clock-names = "iface", "core", "xo";
+ resets = <&gcc GCC_SDCC1_BCR>;
+ mmc-ddr-1_8v;
+ bus-width = <8>;
+ non-removable;
+ status = "disabled";
+ };
+
+ sdhc_2: mmc@7864900 {
+ compatible = "qcom,msm8916-sdhci", "qcom,sdhci-msm-v4";
+ reg = <0x07864900 0x11c>, <0x07864000 0x800>;
+ reg-names = "hc", "core";
+
+ interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 221 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "hc_irq", "pwr_irq";
+ clocks = <&gcc GCC_SDCC2_AHB_CLK>,
+ <&gcc GCC_SDCC2_APPS_CLK>,
+ <&rpmcc RPM_SMD_XO_CLK_SRC>;
+ clock-names = "iface", "core", "xo";
+ resets = <&gcc GCC_SDCC2_BCR>;
+ bus-width = <4>;
+ status = "disabled";
+ };
+
+ blsp_dma: dma-controller@7884000 {
+ compatible = "qcom,bam-v1.7.0";
+ reg = <0x07884000 0x23000>;
+ interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "bam_clk";
+ #dma-cells = <1>;
+ qcom,ee = <0>;
+ status = "disabled";
+ };
+
+ blsp1_uart1: serial@78af000 {
+ compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+ reg = <0x078af000 0x200>;
+ interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_UART1_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ dmas = <&blsp_dma 0>, <&blsp_dma 1>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&blsp1_uart1_default>;
+ pinctrl-1 = <&blsp1_uart1_sleep>;
+ status = "disabled";
+ };
+
+ blsp1_uart2: serial@78b0000 {
+ compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+ reg = <0x078b0000 0x200>;
+ interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_UART2_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ dmas = <&blsp_dma 2>, <&blsp_dma 3>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&blsp1_uart2_default>;
+ pinctrl-1 = <&blsp1_uart2_sleep>;
+ status = "disabled";
+ };
+
+ blsp_i2c1: i2c@78b5000 {
+ compatible = "qcom,i2c-qup-v2.2.1";
+ reg = <0x078b5000 0x500>;
+ interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_QUP1_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ dmas = <&blsp_dma 4>, <&blsp_dma 5>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&i2c1_default>;
+ pinctrl-1 = <&i2c1_sleep>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ blsp_spi1: spi@78b5000 {
+ compatible = "qcom,spi-qup-v2.2.1";
+ reg = <0x078b5000 0x500>;
+ interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_QUP1_SPI_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ dmas = <&blsp_dma 4>, <&blsp_dma 5>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&spi1_default>;
+ pinctrl-1 = <&spi1_sleep>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ blsp_i2c2: i2c@78b6000 {
+ compatible = "qcom,i2c-qup-v2.2.1";
+ reg = <0x078b6000 0x500>;
+ interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ dmas = <&blsp_dma 6>, <&blsp_dma 7>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&i2c2_default>;
+ pinctrl-1 = <&i2c2_sleep>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ blsp_spi2: spi@78b6000 {
+ compatible = "qcom,spi-qup-v2.2.1";
+ reg = <0x078b6000 0x500>;
+ interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_QUP2_SPI_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ dmas = <&blsp_dma 6>, <&blsp_dma 7>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&spi2_default>;
+ pinctrl-1 = <&spi2_sleep>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ blsp_i2c3: i2c@78b7000 {
+ compatible = "qcom,i2c-qup-v2.2.1";
+ reg = <0x078b7000 0x500>;
+ interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ dmas = <&blsp_dma 8>, <&blsp_dma 9>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&i2c3_default>;
+ pinctrl-1 = <&i2c3_sleep>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ blsp_spi3: spi@78b7000 {
+ compatible = "qcom,spi-qup-v2.2.1";
+ reg = <0x078b7000 0x500>;
+ interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_QUP3_SPI_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ dmas = <&blsp_dma 8>, <&blsp_dma 9>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&spi3_default>;
+ pinctrl-1 = <&spi3_sleep>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ blsp_i2c4: i2c@78b8000 {
+ compatible = "qcom,i2c-qup-v2.2.1";
+ reg = <0x078b8000 0x500>;
+ interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_QUP4_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ dmas = <&blsp_dma 10>, <&blsp_dma 11>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&i2c4_default>;
+ pinctrl-1 = <&i2c4_sleep>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ blsp_spi4: spi@78b8000 {
+ compatible = "qcom,spi-qup-v2.2.1";
+ reg = <0x078b8000 0x500>;
+ interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_QUP4_SPI_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ dmas = <&blsp_dma 10>, <&blsp_dma 11>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&spi4_default>;
+ pinctrl-1 = <&spi4_sleep>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ blsp_i2c5: i2c@78b9000 {
+ compatible = "qcom,i2c-qup-v2.2.1";
+ reg = <0x078b9000 0x500>;
+ interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_QUP5_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ dmas = <&blsp_dma 12>, <&blsp_dma 13>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&i2c5_default>;
+ pinctrl-1 = <&i2c5_sleep>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ blsp_spi5: spi@78b9000 {
+ compatible = "qcom,spi-qup-v2.2.1";
+ reg = <0x078b9000 0x500>;
+ interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_QUP5_SPI_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ dmas = <&blsp_dma 12>, <&blsp_dma 13>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&spi5_default>;
+ pinctrl-1 = <&spi5_sleep>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ blsp_i2c6: i2c@78ba000 {
+ compatible = "qcom,i2c-qup-v2.2.1";
+ reg = <0x078ba000 0x500>;
+ interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_QUP6_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ dmas = <&blsp_dma 14>, <&blsp_dma 15>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&i2c6_default>;
+ pinctrl-1 = <&i2c6_sleep>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ blsp_spi6: spi@78ba000 {
+ compatible = "qcom,spi-qup-v2.2.1";
+ reg = <0x078ba000 0x500>;
+ interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_QUP6_SPI_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ dmas = <&blsp_dma 14>, <&blsp_dma 15>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&spi6_default>;
+ pinctrl-1 = <&spi6_sleep>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ usb: usb@78d9000 {
+ compatible = "qcom,ci-hdrc";
+ reg = <0x078d9000 0x200>,
+ <0x078d9200 0x200>;
+ interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_USB_HS_AHB_CLK>,
+ <&gcc GCC_USB_HS_SYSTEM_CLK>;
+ clock-names = "iface", "core";
+ assigned-clocks = <&gcc GCC_USB_HS_SYSTEM_CLK>;
+ assigned-clock-rates = <80000000>;
+ resets = <&gcc GCC_USB_HS_BCR>;
+ reset-names = "core";
+ #reset-cells = <1>;
+ phy_type = "ulpi";
+ dr_mode = "otg";
+ ahb-burst-config = <0>;
+ phy-names = "usb-phy";
+ phys = <&usb_hs_phy>;
+ status = "disabled";
+
+ ulpi {
+ usb_hs_phy: phy {
+ compatible = "qcom,usb-hs-phy-msm8916",
+ "qcom,usb-hs-phy";
+ clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>, <&gcc GCC_USB2A_PHY_SLEEP_CLK>;
+ clock-names = "ref", "sleep";
+ resets = <&gcc GCC_USB2A_PHY_BCR>, <&usb 0>;
+ reset-names = "phy", "por";
+ #phy-cells = <0>;
+ qcom,init-seq = /bits/ 8 <0x0 0x44
+ 0x1 0x6b 0x2 0x24 0x3 0x13>;
+ };
+ };
+ };
+
+ intc: interrupt-controller@b000000 {
+ compatible = "qcom,msm-qgic2";
+ reg = <0x0b000000 0x1000>, <0x0b002000 0x2000>,
+ <0x0b001000 0x1000>, <0x0b004000 0x2000>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ interrupts = <GIC_PPI 0 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_HIGH)>;
+ };
+
+ apcs1_mbox: mailbox@b011000 {
+ compatible = "qcom,msm8939-apcs-kpss-global", "syscon";
+ reg = <0x0b011000 0x1000>;
+ clocks = <&a53pll_c1>, <&gcc GPLL0_VOTE>, <&rpmcc RPM_SMD_XO_CLK_SRC>;
+ clock-names = "pll", "aux", "ref";
+ #clock-cells = <0>;
+ assigned-clocks = <&apcs2>;
+ assigned-clock-rates = <297600000>;
+ #mbox-cells = <1>;
+ };
+
+ a53pll_c1: clock@b016000 {
+ compatible = "qcom,msm8939-a53pll";
+ reg = <0x0b016000 0x40>;
+ #clock-cells = <0>;
+ };
+
+ acc0: clock-controller@b088000 {
+ compatible = "qcom,kpss-acc-v2";
+ reg = <0x0b088000 0x1000>;
+ };
+
+ saw0: power-manager@b089000 {
+ compatible = "qcom,msm8939-saw2-v3.0-cpu", "qcom,saw2";
+ reg = <0x0b089000 0x1000>;
+ };
+
+ acc1: clock-controller@b098000 {
+ compatible = "qcom,kpss-acc-v2";
+ reg = <0x0b098000 0x1000>;
+ };
+
+ saw1: power-manager@b099000 {
+ compatible = "qcom,msm8939-saw2-v3.0-cpu", "qcom,saw2";
+ reg = <0x0b099000 0x1000>;
+ };
+
+ acc2: clock-controller@b0a8000 {
+ compatible = "qcom,kpss-acc-v2";
+ reg = <0x0b0a8000 0x1000>;
+ };
+
+ saw2: power-manager@b0a9000 {
+ compatible = "qcom,msm8939-saw2-v3.0-cpu", "qcom,saw2";
+ reg = <0x0b0a9000 0x1000>;
+ };
+
+ acc3: clock-controller@b0b8000 {
+ compatible = "qcom,kpss-acc-v2";
+ reg = <0x0b0b8000 0x1000>;
+ };
+
+ saw3: power-manager@b0b9000 {
+ compatible = "qcom,msm8939-saw2-v3.0-cpu", "qcom,saw2";
+ reg = <0x0b0b9000 0x1000>;
+ };
+
+ apcs0_mbox: mailbox@b111000 {
+ compatible = "qcom,msm8939-apcs-kpss-global", "syscon";
+ reg = <0x0b111000 0x1000>;
+ clocks = <&a53pll_c0>, <&gcc GPLL0_VOTE>, <&rpmcc RPM_SMD_XO_CLK_SRC>;
+ clock-names = "pll", "aux", "ref";
+ #clock-cells = <0>;
+ #mbox-cells = <1>;
+ };
+
+ a53pll_c0: clock@b116000 {
+ compatible = "qcom,msm8939-a53pll";
+ reg = <0x0b116000 0x40>;
+ #clock-cells = <0>;
+ };
+
+ acc4: clock-controller@b188000 {
+ compatible = "qcom,kpss-acc-v2";
+ reg = <0x0b188000 0x1000>;
+ };
+
+ saw4: power-manager@b189000 {
+ compatible = "qcom,msm8939-saw2-v3.0-cpu", "qcom,saw2";
+ reg = <0x0b189000 0x1000>;
+ };
+
+ acc5: clock-controller@b198000 {
+ compatible = "qcom,kpss-acc-v2";
+ reg = <0x0b198000 0x1000>;
+ };
+
+ saw5: power-manager@b199000 {
+ compatible = "qcom,msm8939-saw2-v3.0-cpu", "qcom,saw2";
+ reg = <0x0b199000 0x1000>;
+ };
+
+ acc6: clock-controller@b1a8000 {
+ compatible = "qcom,kpss-acc-v2";
+ reg = <0x0b1a8000 0x1000>;
+ };
+
+ saw6: power-manager@b1a9000 {
+ compatible = "qcom,msm8939-saw2-v3.0-cpu", "qcom,saw2";
+ reg = <0x0b1a9000 0x1000>;
+ };
+
+ acc7: clock-controller@b1b8000 {
+ compatible = "qcom,kpss-acc-v2";
+ reg = <0x0b1b8000 0x1000>;
+ };
+
+ saw7: power-manager@b1b9000 {
+ compatible = "qcom,msm8939-saw2-v3.0-cpu", "qcom,saw2";
+ reg = <0x0b1b9000 0x1000>;
+ };
+
+ a53pll_cci: clock@b1d0000 {
+ compatible = "qcom,msm8939-a53pll";
+ reg = <0x0b1d0000 0x40>;
+ #clock-cells = <0>;
+ };
+
+ apcs2: mailbox@b1d1000 {
+ compatible = "qcom,msm8939-apcs-kpss-global", "syscon";
+ reg = <0x0b1d1000 0x1000>;
+ clocks = <&a53pll_cci>, <&gcc GPLL0_VOTE>, <&rpmcc RPM_SMD_XO_CLK_SRC>;
+ clock-names = "pll", "aux", "ref";
+ #clock-cells = <0>;
+ #mbox-cells = <1>;
+ };
+
+ timer@b020000 {
+ compatible = "arm,armv7-timer-mem";
+ reg = <0x0b020000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ frame@b021000 {
+ reg = <0x0b021000 0x1000>,
+ <0x0b022000 0x1000>;
+ interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+ frame-number = <0>;
+ };
+
+ frame@b023000 {
+ reg = <0x0b023000 0x1000>;
+ interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+ frame-number = <1>;
+ status = "disabled";
+ };
+
+ frame@b024000 {
+ reg = <0x0b024000 0x1000>;
+ interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+ frame-number = <2>;
+ status = "disabled";
+ };
+
+ frame@b025000 {
+ reg = <0x0b025000 0x1000>;
+ interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+ frame-number = <3>;
+ status = "disabled";
+ };
+
+ frame@b026000 {
+ reg = <0x0b026000 0x1000>;
+ interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+ frame-number = <4>;
+ status = "disabled";
+ };
+
+ frame@b027000 {
+ reg = <0x0b027000 0x1000>;
+ interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+ frame-number = <5>;
+ status = "disabled";
+ };
+
+ frame@b028000 {
+ reg = <0x0b028000 0x1000>;
+ interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+ frame-number = <6>;
+ status = "disabled";
+ };
+ };
+
+ pronto: remoteproc@a204000 {
+ compatible = "qcom,pronto-v2-pil", "qcom,pronto";
+ reg = <0x0a204000 0x2000>,
+ <0x0a202000 0x1000>,
+ <0x0a21b000 0x3000>;
+ reg-names = "ccu", "dxe", "pmu";
+
+ interrupts-extended = <&intc 0 149 IRQ_TYPE_EDGE_RISING>,
+ <&wcnss_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
+ <&wcnss_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
+ <&wcnss_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
+ <&wcnss_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
+ interrupt-names = "wdog", "fatal", "ready", "handover", "stop-ack";
+
+ memory-region = <&wcnss_mem>;
+
+ power-domains = <&rpmpd MSM8939_VDDCX>,
+ <&rpmpd MSM8939_VDDMX_AO>;
+ power-domain-names = "cx", "mx";
+
+ qcom,smem-states = <&wcnss_smp2p_out 0>;
+ qcom,smem-state-names = "stop";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&wcnss_pin_a>;
+
+ status = "disabled";
+
+ iris {
+ compatible = "qcom,wcn3620";
+ clocks = <&rpmcc RPM_SMD_RF_CLK2>;
+ clock-names = "xo";
+ };
+
+ smd-edge {
+ interrupts = <GIC_SPI 142 1>;
+ qcom,ipc = <&apcs1_mbox 8 17>;
+ qcom,smd-edge = <6>;
+ qcom,remote-pid = <4>;
+
+ label = "pronto";
+
+ wcnss {
+ compatible = "qcom,wcnss";
+ qcom,smd-channels = "WCNSS_CTRL";
+
+ qcom,mmio = <&pronto>;
+
+ bluetooth {
+ compatible = "qcom,wcnss-bt";
+ };
+
+ wifi {
+ compatible = "qcom,wcnss-wlan";
+
+ interrupts = <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "tx", "rx";
+
+ qcom,smem-states = <&apps_smsm 10>,
+ <&apps_smsm 9>;
+ qcom,smem-state-names = "tx-enable",
+ "tx-rings-empty";
+ };
+ };
+ };
+ };
+ };
+
+ smd {
+ compatible = "qcom,smd";
+
+ rpm {
+ interrupts = <GIC_SPI 168 IRQ_TYPE_EDGE_RISING>;
+ qcom,ipc = <&apcs1_mbox 8 0>;
+ qcom,smd-edge = <15>;
+
+ rpm_requests: rpm-requests {
+ compatible = "qcom,rpm-msm8936";
+ qcom,smd-channels = "rpm_requests";
+
+ rpmcc: clock-controller {
+ compatible = "qcom,rpmcc-msm8936", "qcom,rpmcc";
+ #clock-cells = <1>;
+ clock-names = "xo";
+ clocks = <&xo_board>;
+ };
+
+ rpmpd: power-controller {
+ compatible = "qcom,msm8939-rpmpd";
+ #power-domain-cells = <1>;
+ operating-points-v2 = <&rpmpd_opp_table>;
+
+ rpmpd_opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ rpmpd_opp_ret: opp1 {
+ opp-level = <1>;
+ };
+
+ rpmpd_opp_svs_krait: opp2 {
+ opp-level = <2>;
+ };
+
+ rpmpd_opp_svs_soc: opp3 {
+ opp-level = <3>;
+ };
+
+ rpmpd_opp_nom: opp4 {
+ opp-level = <4>;
+ };
+
+ rpmpd_opp_turbo: opp5 {
+ opp-level = <5>;
+ };
+
+ rpmpd_opp_super_turbo: opp6 {
+ opp-level = <6>;
+ };
+ };
+ };
+ };
+ };
+ };
+
+ thermal_zones: thermal-zones {
+ cpu0-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens 5>;
+
+ trips {
+ cpu0_alert: trip0 {
+ temperature = <75000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ cpu0_crit: trip1 {
+ temperature = <115000>;
+ hysteresis = <0>;
+ type = "critical";
+ };
+ };
+
+ cooling-maps {
+ map0 {
+ trip = <&cpu0_alert>;
+ cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+ };
+
+ cpu1-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens 6>;
+
+ trips {
+ cpu1_alert: trip0 {
+ temperature = <75000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ cpu1_crit: trip1 {
+ temperature = <110000>;
+ hysteresis = <2000>;
+ type = "critical";
+ };
+ };
+
+ cooling-maps {
+ map0 {
+ trip = <&cpu1_alert>;
+ cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+ };
+
+ cpu2-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens 7>;
+
+ trips {
+ cpu2_alert: trip0 {
+ temperature = <75000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ cpu2_crit: trip1 {
+ temperature = <110000>;
+ hysteresis = <2000>;
+ type = "critical";
+ };
+ };
+
+ cooling-maps {
+ map0 {
+ trip = <&cpu2_alert>;
+ cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+ };
+
+ cpu3-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens 8>;
+
+ trips {
+ cpu3_alert: trip0 {
+ temperature = <75000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ cpu3_crit: trip1 {
+ temperature = <110000>;
+ hysteresis = <2000>;
+ type = "critical";
+ };
+ };
+
+ cooling-maps {
+ map0 {
+ trip = <&cpu3_alert>;
+ cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+ };
+
+ cpu4567-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens 9>;
+
+ trips {
+ cpu4567_alert: trip0 {
+ temperature = <75000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ cpu4567_crit: trip1 {
+ temperature = <110000>;
+ hysteresis = <2000>;
+ type = "critical";
+ };
+ };
+
+ cooling-maps {
+ map0 {
+ trip = <&cpu4567_alert>;
+ cooling-device = <&cpu4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+ };
+
+ gpu-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens 3>;
+
+ trips {
+ gpu_alert0: trip-point0 {
+ temperature = <75000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+
+ gpu_crit: gpu_crit {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "critical";
+ };
+ };
+ };
+
+ modem1-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens 0>;
+
+ trips {
+ modem1_alert0: trip-point0 {
+ temperature = <85000>;
+ hysteresis = <2000>;
+ type = "hot";
+ };
+ };
+ };
+
+ modem2-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens 2>;
+
+ trips {
+ modem2_alert0: trip-point0 {
+ temperature = <85000>;
+ hysteresis = <2000>;
+ type = "hot";
+ };
+ };
+ };
+
+ camera-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens 1>;
+
+ trips {
+ cam_alert0: trip-point0 {
+ temperature = <75000>;
+ hysteresis = <2000>;
+ type = "hot";
+ };
+ };
+ };
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>;
+ };
+
+ /* Dummy regulator for our non-psci cpu@X defintions */
+ vreg_dummy: regulator-dummy {
+ #power-domain-cells = <0>;
+ };
+
+ smp2p-wcnss {
+ compatible = "qcom,smp2p";
+ qcom,smem = <451>, <431>;
+
+ interrupts = <GIC_SPI 143 IRQ_TYPE_EDGE_RISING>;
+
+ mboxes = <&apcs1_mbox 18>;
+
+ qcom,local-pid = <0>;
+ qcom,remote-pid = <4>;
+
+ wcnss_smp2p_out: master-kernel {
+ qcom,entry-name = "master-kernel";
+
+ #qcom,smem-state-cells = <1>;
+ };
+
+ wcnss_smp2p_in: slave-kernel {
+ qcom,entry-name = "slave-kernel";
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+};
--
2.38.1
^ permalink raw reply related [flat|nested] 32+ messages in thread
* [PATCH v3 6/8] arm64: dts: qcom: Add msm8939-pm8916.dtsi include
2023-01-17 2:48 [PATCH v3 0/8] Add MSM8939 SoC support with two devices Bryan O'Donoghue
` (4 preceding siblings ...)
2023-01-17 2:48 ` [PATCH v3 5/8] arm64: dts: qcom: Add msm8939 SoC Bryan O'Donoghue
@ 2023-01-17 2:48 ` Bryan O'Donoghue
2023-01-18 13:49 ` Konrad Dybcio
2023-01-17 2:48 ` [PATCH v3 7/8] arm64: dts: qcom: Add Square apq8039-t2 board Bryan O'Donoghue
` (2 subsequent siblings)
8 siblings, 1 reply; 32+ messages in thread
From: Bryan O'Donoghue @ 2023-01-17 2:48 UTC (permalink / raw)
To: agross, andersson, konrad.dybcio, djakov, robh+dt,
krzysztof.kozlowski+dt
Cc: bryan.odonoghue, linux-arm-msm, linux-pm, devicetree,
linux-kernel, benl, shawn.guo, fabien.parent, leo.yan,
dmitry.baryshkov, Stephan Gerhold
From: Stephan Gerhold <stephan@gerhold.net>
The msm8939-pm8916.dtsi include configures the regulator supplies of
MSM8939 used together with PM8916, as recommended by Qualcomm. In rare
cases where boards deviate from the recommended design they can just
avoid using this include.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
---
arch/arm64/boot/dts/qcom/msm8939-pm8916.dtsi | 82 ++++++++++++++++++++
1 file changed, 82 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/msm8939-pm8916.dtsi
diff --git a/arch/arm64/boot/dts/qcom/msm8939-pm8916.dtsi b/arch/arm64/boot/dts/qcom/msm8939-pm8916.dtsi
new file mode 100644
index 0000000000000..18a1b3cca01d6
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8939-pm8916.dtsi
@@ -0,0 +1,82 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+#include "msm8939.dtsi"
+#include "pm8916.dtsi"
+
+&dsi0 {
+ vdda-supply = <&pm8916_l2>;
+ vddio-supply = <&pm8916_l6>;
+};
+
+&dsi1 {
+ vdda-supply = <&pm8916_l2>;
+ vddio-supply = <&pm8916_l6>;
+};
+
+&dsi_phy0 {
+ vddio-supply = <&pm8916_l6>;
+};
+
+&dsi_phy1 {
+ vddio-supply = <&pm8916_l6>;
+};
+
+&mpss {
+ pll-supply = <&pm8916_l7>;
+};
+
+&pronto {
+ vddpx-supply = <&pm8916_l7>;
+
+ iris {
+ vddxo-supply = <&pm8916_l7>;
+ vddrfa-supply = <&pm8916_s3>;
+ vddpa-supply = <&pm8916_l9>;
+ vdddig-supply = <&pm8916_l5>;
+ };
+};
+
+&sdhc_1 {
+ vmmc-supply = <&pm8916_l8>;
+ vqmmc-supply = <&pm8916_l5>;
+};
+
+&sdhc_2 {
+ vmmc-supply = <&pm8916_l11>;
+ vqmmc-supply = <&pm8916_l12>;
+};
+
+&usb_hs_phy {
+ v1p8-supply = <&pm8916_l7>;
+ v3p3-supply = <&pm8916_l13>;
+};
+
+&rpm_requests {
+ smd_rpm_regulators: regulators {
+ compatible = "qcom,rpm-pm8916-regulators";
+
+ /* pm8916_s1 is managed by rpmpd (MSM8939_VDDMDCX) */
+ /* pm8916_s2 is managed by rpmpd (MSM8939_VDDCX) */
+ pm8916_s3: s3 {};
+ pm8916_s4: s4 {};
+
+ pm8916_l1: l1 {};
+ pm8916_l2: l2 {};
+ /* pm8916_l3 is managed by rpmpd (MSM8939_VDDMX) */
+ pm8916_l4: l4 {};
+ pm8916_l5: l5 {};
+ pm8916_l6: l6 {};
+ pm8916_l7: l7 {};
+ pm8916_l8: l8 {};
+ pm8916_l9: l9 {};
+ pm8916_l10: l10 {};
+ pm8916_l11: l11 {};
+ pm8916_l12: l12 {};
+ pm8916_l13: l13 {};
+ pm8916_l14: l14 {};
+ pm8916_l15: l15 {};
+ pm8916_l16: l16 {};
+ pm8916_l17: l17 {};
+ pm8916_l18: l18 {};
+ };
+};
--
2.38.1
^ permalink raw reply related [flat|nested] 32+ messages in thread
* [PATCH v3 7/8] arm64: dts: qcom: Add Square apq8039-t2 board
2023-01-17 2:48 [PATCH v3 0/8] Add MSM8939 SoC support with two devices Bryan O'Donoghue
` (5 preceding siblings ...)
2023-01-17 2:48 ` [PATCH v3 6/8] arm64: dts: qcom: Add msm8939-pm8916.dtsi include Bryan O'Donoghue
@ 2023-01-17 2:48 ` Bryan O'Donoghue
2023-01-17 21:06 ` Bjorn Andersson
2023-01-17 2:48 ` [PATCH v3 8/8] arm64: dts: qcom: Add msm8939 Sony Xperia M4 Aqua Bryan O'Donoghue
2023-01-18 22:50 ` (subset) [PATCH v3 0/8] Add MSM8939 SoC support with two devices Bjorn Andersson
8 siblings, 1 reply; 32+ messages in thread
From: Bryan O'Donoghue @ 2023-01-17 2:48 UTC (permalink / raw)
To: agross, andersson, konrad.dybcio, djakov, robh+dt,
krzysztof.kozlowski+dt
Cc: bryan.odonoghue, linux-arm-msm, linux-pm, devicetree,
linux-kernel, benl, shawn.guo, fabien.parent, leo.yan,
dmitry.baryshkov, Jun Nie, James Willcox, Joseph Gates, Max Chen,
Zac Crosby
The apq8039-t2 is an apq8039 based board paired with a wcn3680b WiFi
chipset.
Co-developed-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Co-developed-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Co-developed-by: Benjamin Li <benl@squareup.com>
Signed-off-by: Benjamin Li <benl@squareup.com>
Co-developed-by: James Willcox <jwillcox@squareup.com>
Signed-off-by: James Willcox <jwillcox@squareup.com>
Co-developed-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Co-developed-by: Joseph Gates <jgates@squareup.com>
Signed-off-by: Joseph Gates <jgates@squareup.com>
Co-developed-by: Max Chen <mchen@squareup.com>
Signed-off-by: Max Chen <mchen@squareup.com>
Co-developed-by: Zac Crosby <zac@squareup.com>
Signed-off-by: Zac Crosby <zac@squareup.com>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
---
arch/arm64/boot/dts/qcom/Makefile | 1 +
arch/arm64/boot/dts/qcom/apq8039-t2.dts | 557 ++++++++++++++++++++++++
2 files changed, 558 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/apq8039-t2.dts
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index e442a81895d04..5c47d1fb50b01 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -1,5 +1,6 @@
# SPDX-License-Identifier: GPL-2.0
dtb-$(CONFIG_ARCH_QCOM) += apq8016-sbc.dtb
+dtb-$(CONFIG_ARCH_QCOM) += apq8039-t2.dtb
dtb-$(CONFIG_ARCH_QCOM) += apq8094-sony-xperia-kitakami-karin_windy.dtb
dtb-$(CONFIG_ARCH_QCOM) += apq8096-db820c.dtb
dtb-$(CONFIG_ARCH_QCOM) += apq8096-ifc6640.dtb
diff --git a/arch/arm64/boot/dts/qcom/apq8039-t2.dts b/arch/arm64/boot/dts/qcom/apq8039-t2.dts
new file mode 100644
index 0000000000000..21f5a21f76135
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/apq8039-t2.dts
@@ -0,0 +1,557 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2015, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2020-2023, Linaro Ltd.
+ *
+ */
+
+/dts-v1/;
+
+#include "msm8939.dtsi"
+#include "msm8939-pm8916.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include <dt-bindings/sound/apq8016-lpass.h>
+
+/ {
+ model = "Square, Inc. T2 Devkit";
+ compatible = "square,apq8039-t2", "qcom,msm8939";
+
+ qcom,board-id = <0x53 0x54>;
+ qcom,msm-id = <239 0>, <239 0x30000>, <241 0x30000>, <263 0x30000>;
+
+ aliases {
+ mmc0 = &sdhc_1;
+ mmc1 = &sdhc_2;
+ serial0 = &blsp1_uart1;
+ serial1 = &blsp1_uart2;
+ };
+
+ bl: backlight {
+ compatible = "gpio-backlight";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_backlight>;
+ gpios = <&tlmm 98 GPIO_ACTIVE_HIGH>;
+ };
+
+ chosen {
+ stdout-path = "serial1:115200n8";
+ };
+
+ lcd_iovcc_reg: lcd-iovcc-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "lcd_iovcc";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lcd_iovcc_reg>;
+ gpio = <&tlmm 9 GPIO_ACTIVE_HIGH>;
+ startup-delay-us = <300>;
+ enable-active-high;
+ };
+
+ lcd_avdd_reg: lcd-avdd-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "lcd_avdd";
+ regulator-min-microvolt = <5600000>;
+ regulator-max-microvolt = <5600000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lcd_avdd_reg>;
+ gpio = <&tlmm 86 GPIO_ACTIVE_HIGH>;
+ startup-delay-us = <300>;
+ enable-active-high;
+ };
+
+ lcd_avee_reg: lcd-avee-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "lcd_avee";
+ regulator-min-microvolt = <5600000>;
+ regulator-max-microvolt = <5600000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lcd_avee_reg>;
+ gpio = <&tlmm 87 GPIO_ACTIVE_HIGH>;
+ startup-delay-us = <300>;
+ enable-active-high;
+ };
+
+ pp_spe_3v3_reg: pp-spe-3v3-regulator {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&tlmm_spe_reg>;
+ regulator-name = "pp_spe_3v3";
+ gpio = <&tlmm 108 GPIO_ACTIVE_HIGH>;
+ startup-delay-us = <0>;
+ enable-active-high;
+ };
+
+ pp_crq_3v3_reg: pp-crq-3v3-regulator {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&tlmm_crq_reg>;
+ regulator-name = "pp_crq_3v3";
+ gpio = <&tlmm 12 GPIO_ACTIVE_HIGH>;
+ startup-delay-us = <0>;
+ enable-active-high;
+ };
+};
+
+&blsp_dma {
+ status = "okay";
+};
+
+&blsp_i2c1 {
+ status = "okay";
+};
+
+&blsp_i2c2 {
+ status = "okay";
+};
+
+&blsp_i2c3 {
+ status = "okay";
+
+ typec: tps6598x@38 {
+ compatible = "ti,tps6598x";
+ reg = <0x38>;
+
+ interrupt-parent = <&tlmm>;
+ interrupts = <107 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-names = "irq";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&typec_irq>;
+
+ typec_con: connector {
+ compatible = "usb-c-connector";
+ label = "USB-C";
+ port {
+ typec_ep: endpoint {
+ remote-endpoint = <&otg_ep>;
+ };
+ };
+ };
+ };
+};
+
+&blsp_i2c5 {
+ status = "okay";
+};
+
+&blsp1_uart1 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&blsp1_uart1_default>;
+ pinctrl-1 = <&blsp1_uart1_sleep>;
+ status = "okay";
+};
+
+&blsp1_uart2 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&blsp1_uart2_default>;
+ pinctrl-1 = <&blsp1_uart2_sleep>;
+ status = "okay";
+};
+
+&lpass {
+ status = "okay";
+};
+
+/*
+ * Line names are taken from the schematic of T2, Ver X03.
+ * July 14, 2018. Page 4 in particular.
+ */
+
+&tlmm {
+ gpio-line-names =
+ "APQ_UART1_TX", /* GPIO_0 */
+ "APQ_UART1_RX",
+ "APQ_I2C1_SDA",
+ "APQ_I2C1_SCL",
+ "APQ_UART2_TX_1V8",
+ "APQ_UART2_RX_1V8",
+ "APQ_I2C2_SDA",
+ "APQ_I2C2_SCL",
+ "NC",
+ "APQ_LCD_IOVCC_EN",
+ "APQ_I2C3_SDA", /* GPIO_10 */
+ "APQ_I2C3_SCL",
+ "TOUCH_RST_1V8_L",
+ "NC",
+ "APQ_I2C4_SDA",
+ "APQ_I2C4_SCL",
+ "APQ_ID5",
+ "USB_DISCONNECT",
+ "APQ_I2C5_SDA",
+ "APQ_I2C5_SCL",
+ "APQ_USBC_SPI_MOSI", /* GPIO_20 */
+ "APQ_USBC_SPI_MISO",
+ "APQ_USBC_SPI_SS_L",
+ "APQ_USBC_SPI_CLK",
+ "APQ_LCD_TE0",
+ "APQ_LCD_RST_L",
+ "NC",
+ "NC",
+ "ACCELEROMETER_INT1",
+ "APQ_CAM_I2C0_SDA",
+ "APQ_CAM_I2C0_SCL", /* GPIO_30 */
+ "ACCELEROMETER_INT2",
+ "NC",
+ "NC",
+ "NC",
+ "APQ_K21_RST_1V8_L",
+ "NC",
+ "APQ_EDL_1V8",
+ "TP145",
+ "BT_SSBI",
+ "NC", /* GPIO_40 */
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "BT_CTRL",
+ "BT_DAT",
+ "PWR_GPIO_IN",
+ "PWR_GPIO_OUT", /* GPIO_50 */
+ "CARD_DET_MLB_L",
+ "HALL_SENSOR",
+ "TP63",
+ "TP64",
+ "TP65",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "NC", /* GPIO_60 */
+ "NC",
+ "APQ_K21_GPIO0_1V8",
+ "CDC_PDM_CLK",
+ "CDC_PDM_SYNC",
+ "CDC_PDM_TX",
+ "CDC_PDM_RX0",
+ "CDC_PDM_RX1",
+ "CDC_PDM_RX2",
+ "APQ_K21_GPIO1_1V8",
+ "NC", /* GPIO_70 */
+ "APQ_HUB_SEL_1V8",
+ "APQ_K21_GPIO2_1V8",
+ "APQ_K21_GPIO3_1V8",
+ "APQ_ID0",
+ "APQ_ID1",
+ "APQ_ID2",
+ "APQ_ID3",
+ "APQ_ID4",
+ "APQ_HUB_SUSP_IND",
+ "BOOT_CONFIG_0", /* GPIO_80 */
+ "BOOT_CONFIG_1",
+ "BOOT_CONFIG_2",
+ "BOOT_CONFIG_3",
+ "NC",
+ "NC",
+ "APQ_LCD_AVDD_EN",
+ "APQ_LCD_AVEE_EN",
+ "TP70",
+ "NC",
+ "APQ_DEBUG0", /* GPIO_90 */
+ "APQ_DEBUG1",
+ "APQ_DEBUG2",
+ "APQ_DEBUG3",
+ "TP165",
+ "NC",
+ "APQ_LNA_PWR_EN",
+ "NC",
+ "APQ_LCD_BL_EN",
+ "NC",
+ "APQ_LCD_ID0", /* GPIO_100 */
+ "APQ_LCD_ID1",
+ "USBC_GPIO5_1V8",
+ "NC",
+ "NC",
+ "NC",
+ "APQ_HUB_RST_1V8_L",
+ "USBC_I2C_IRQ_1V8_L",
+ "SPE_PWR_EN",
+ "NC",
+ "APQ_USB_ID", /* GPIO_110 */
+ "APQ_EXT_BUCK_VSEL",
+ "APQ_USB_ID_OUT",
+ "NC",
+ "PRNT_RST_L",
+ "APQ_CRQ_I2C_RDY_1V8",
+ "TYPEC_RST_1V8_H",
+ "CHG_BACKPWR_EN",
+ "CHG_PROCHOT_L",
+ "NC",
+ "USBC_GPIO7_1V8", /* GPIO_120 */
+ "NC";
+
+ blsp1_uart1_default: blsp1-uart1-default-state {
+ pins = "gpio0", "gpio1";
+ function = "blsp_uart1";
+ drive-strength = <16>;
+ bias-disable;
+ };
+
+ blsp1_uart1_sleep: blsp1-uart1-sleep-state {
+ pins = "gpio0", "gpio1";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ pinctrl_lcd_iovcc_reg: lcd-iovcc-reg-state {
+ pins = "gpio9";
+ function = "gpio";
+ };
+
+ tlmm_crq_reg: tlmm-crq-reg-state {
+ function = "gpio";
+ pins = "gpio12";
+ output-high;
+ };
+
+ pinctrl_otg_host: otg-host-state {
+ function = "gpio";
+ pins = "gpio17";
+ output-low;
+ };
+
+ pinctrl_otg_device: otg-device-state {
+ function = "gpio";
+ pins = "gpio17";
+ output-low;
+ };
+
+ pinctrl_otg_default: otg-default-state {
+ function = "gpio";
+ pins = "gpio17";
+ output-high;
+ };
+
+ pinctrl_lcd_rst: lcd-rst-state {
+ pins = "gpio25";
+ function = "gpio";
+ };
+
+ sq_spe_enable: sq-spe-enable-state {
+ pins = "gpio35";
+ function = "gpio";
+ output-low;
+ };
+
+ pinctrl_lcd_avdd_reg: lcd-avdd-reg-state {
+ pins = "gpio86";
+ function = "gpio";
+ };
+
+ pinctrl_lcd_avee_reg: lcd-avee-reg-state {
+ pins = "gpio87";
+ function = "gpio";
+ };
+
+ pinctrl_backlight: backlight-state {
+ pins = "gpio98";
+ function = "gpio";
+ };
+
+ typec_irq: typec-irq-state {
+ function = "gpio";
+ pins = "gpio107";
+ bias-pull-up;
+ input-enable;
+ };
+
+ tlmm_spe_reg: tlmm-spe-reg-state {
+ pins = "gpio108";
+ function = "gpio";
+ output-high;
+ };
+
+ ext_buck_vsel_reg: ext-buck-vsel-reg-state {
+ function = "gpio";
+ pins = "gpio111";
+ drive-strength = <2>;
+ };
+};
+
+&pm8916_gpios {
+ gpio-line-names =
+ "PM_GPIO1", /* WIFI_GPIO1_PRE */
+ "PM_GPIO2", /* WIFI_GPIO2_PRE */
+ "PM_GPIO3",
+ "PM_GPIO4";
+};
+
+&pronto {
+ pinctrl-names = "default";
+ pinctrl-0 = <&wcnss_pin_a>;
+ status = "okay";
+
+ iris {
+ compatible = "qcom,wcn3680";
+ };
+};
+
+&smd_rpm_regulators {
+ vdd_l1_l2_l3-supply = <&pm8916_s3>;
+ vdd_l4_l5_l6-supply = <&pm8916_s4>;
+ vdd_l7-supply = <&pm8916_s4>;
+
+ pm8916_s3: s3 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1300000>;
+ };
+
+ pm8916_s4: s4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2100000>;
+ };
+
+ /* l1 is fixed to 1225000, but not connected in schematic */
+
+ pm8916_l2: l2 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ pm8916_l4: l4 {
+ regulator-min-microvolt = <2050000>;
+ regulator-max-microvolt = <2050000>;
+ };
+
+ pm8916_l5: l5 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ pm8916_l6: l6 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ pm8916_l7: l7 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ pm8916_l8: l8 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2900000>;
+ };
+
+ pm8916_l9: l9 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ pm8916_l10: l10 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ pm8916_l11: l11 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+ };
+
+ pm8916_l12: l12 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+ };
+
+ pm8916_l13: l13 {
+ regulator-min-microvolt = <3075000>;
+ regulator-max-microvolt = <3075000>;
+ };
+
+ pm8916_l14: l14 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ pm8916_l15: l15 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ pm8916_l16: l16 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ pm8916_l17: l17 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ };
+
+ pm8916_l18: l18 {
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2700000>;
+ };
+};
+
+&sdhc_1 {
+ vmmc-supply = <&pm8916_l8>;
+ vqmmc-supply = <&pm8916_l5>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&sdc1_default_state>;
+ pinctrl-1 = <&sdc1_sleep_state>;
+ status = "okay";
+};
+
+&sound {
+ model = "apq8039-square-sndcard";
+ audio-routing = "AMIC2", "MIC BIAS Internal2";
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&cdc_pdm_lines_default>;
+ pinctrl-1 = <&cdc_pdm_lines_sleep>;
+
+ internal-codec-playback-dai-link {
+ link-name = "WCD";
+ cpu {
+ sound-dai = <&lpass MI2S_PRIMARY>;
+ };
+ codec {
+ sound-dai = <&lpass_codec 0>, <&wcd_codec 0>;
+ };
+ };
+
+ internal-codec-capture-dai-link {
+ link-name = "WCD-Capture";
+ cpu {
+ sound-dai = <&lpass MI2S_TERTIARY>;
+ };
+ codec {
+ sound-dai = <&lpass_codec 1>, <&wcd_codec 1>;
+ };
+ };
+};
+
+&usb {
+ pinctrl-names = "default", "host", "device";
+ pinctrl-0 = <&pinctrl_otg_default>;
+ pinctrl-1 = <&pinctrl_otg_host>;
+ pinctrl-2 = <&pinctrl_otg_device>;
+ pin-switch-delay-us = <100000>;
+ usb-role-switch;
+ status = "okay";
+
+ ulpi {
+ usb_hs_phy: phy {
+ v1p8-supply = <&pm8916_l7>;
+ v3p3-supply = <&pm8916_l13>;
+ };
+ };
+ port {
+ otg_ep: endpoint {
+ remote-endpoint = <&typec_ep>;
+ };
+ };
+};
+
+&wcd_codec {
+ qcom,hphl-jack-type-normally-open;
+ qcom,mbhc-vthreshold-low = <75 150 237 450 500>;
+ qcom,mbhc-vthreshold-high = <75 150 237 450 500>;
+ status = "okay";
+};
--
2.38.1
^ permalink raw reply related [flat|nested] 32+ messages in thread
* [PATCH v3 8/8] arm64: dts: qcom: Add msm8939 Sony Xperia M4 Aqua
2023-01-17 2:48 [PATCH v3 0/8] Add MSM8939 SoC support with two devices Bryan O'Donoghue
` (6 preceding siblings ...)
2023-01-17 2:48 ` [PATCH v3 7/8] arm64: dts: qcom: Add Square apq8039-t2 board Bryan O'Donoghue
@ 2023-01-17 2:48 ` Bryan O'Donoghue
2023-01-18 14:42 ` Konrad Dybcio
2023-01-18 22:50 ` (subset) [PATCH v3 0/8] Add MSM8939 SoC support with two devices Bjorn Andersson
8 siblings, 1 reply; 32+ messages in thread
From: Bryan O'Donoghue @ 2023-01-17 2:48 UTC (permalink / raw)
To: agross, andersson, konrad.dybcio, djakov, robh+dt,
krzysztof.kozlowski+dt
Cc: bryan.odonoghue, linux-arm-msm, linux-pm, devicetree,
linux-kernel, benl, shawn.guo, fabien.parent, leo.yan,
dmitry.baryshkov
Add a basic booting DTS for the Sony Xperia M4 Aqua aka "tulip".
Tulip is paired with:
- wcn3660
- smb1360 battery charger
- 720p Truly NT35521 Panel
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
---
arch/arm64/boot/dts/qcom/Makefile | 1 +
arch/arm64/boot/dts/qcom/apq8039-t2.dts | 2 -
.../qcom/msm8939-sony-xperia-kanuti-tulip.dts | 466 ++++++++++++++++++
3 files changed, 467 insertions(+), 2 deletions(-)
create mode 100644 arch/arm64/boot/dts/qcom/msm8939-sony-xperia-kanuti-tulip.dts
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 5c47d1fb50b01..8b9fa1deadbe0 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -24,6 +24,7 @@ dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-grandmax.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-j5.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-serranove.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8916-wingtech-wt88047.dtb
+dtb-$(CONFIG_ARCH_QCOM) += msm8939-sony-xperia-kanuti-tulip.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8953-motorola-potter.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8953-xiaomi-daisy.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8953-xiaomi-mido.dtb
diff --git a/arch/arm64/boot/dts/qcom/apq8039-t2.dts b/arch/arm64/boot/dts/qcom/apq8039-t2.dts
index 21f5a21f76135..ee04cf294179f 100644
--- a/arch/arm64/boot/dts/qcom/apq8039-t2.dts
+++ b/arch/arm64/boot/dts/qcom/apq8039-t2.dts
@@ -491,8 +491,6 @@ pm8916_l18: l18 {
};
&sdhc_1 {
- vmmc-supply = <&pm8916_l8>;
- vqmmc-supply = <&pm8916_l5>;
pinctrl-names = "default", "sleep";
pinctrl-0 = <&sdc1_default_state>;
pinctrl-1 = <&sdc1_sleep_state>;
diff --git a/arch/arm64/boot/dts/qcom/msm8939-sony-xperia-kanuti-tulip.dts b/arch/arm64/boot/dts/qcom/msm8939-sony-xperia-kanuti-tulip.dts
new file mode 100644
index 0000000000000..ffe3ea17dcae2
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8939-sony-xperia-kanuti-tulip.dts
@@ -0,0 +1,466 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2015, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2022-2023, Bryan O'Donoghue.
+ *
+ */
+
+/dts-v1/;
+
+#include "msm8939.dtsi"
+#include "msm8939-pm8916.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+
+/ {
+ model = "Sony Xperia M4 Aqua";
+ compatible = "sony,kanuti-tulip", "qcom,msm8939";
+
+ qcom,board-id = <8 0>;
+ qcom,msm-id = <239 0>, <239 0x30000>, <241 0x30000>, <263 0x30000>;
+
+ aliases {
+ mmc0 = &sdhc_1; /* SDC1 eMMC slot */
+ mmc1 = &sdhc_2; /* SDC2 SD card slot */
+ serial0 = &blsp1_uart2;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ negative5_reg: negative5-regulator {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&negative5_reg_default>;
+ regulator-name = "negative5_reg";
+ gpio = <&tlmm 17 GPIO_ACTIVE_LOW>;
+ startup-delay-us = <0>;
+ };
+
+ positive5_reg: positive5-regulator {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&positive5_reg_default>;
+ regulator-name = "positive5_reg";
+ gpio = <&tlmm 114 GPIO_ACTIVE_LOW>;
+ startup-delay-us = <0>;
+ };
+
+ usb_id: usb-id {
+ compatible = "linux,extcon-usb-gpio";
+ id-gpio = <&tlmm 110 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb_id_default>;
+ };
+};
+
+&blsp_dma {
+ status = "okay";
+};
+
+&dsi0 {
+ vdda-supply = <&pm8916_l2>;
+ vddio-supply = <&pm8916_l16>;
+ status = "okay";
+
+ panel@0 {
+ compatible = "sony,tulip-truly-nt35521";
+ reg = <0>;
+ positive5-supply = <&positive5_reg>;
+ negative5-supply = <&negative5_reg>;
+ reset-gpios = <&tlmm 25 GPIO_ACTIVE_LOW>;
+ enable-gpios = <&tlmm 10 GPIO_ACTIVE_LOW>;
+
+ ports {
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&dsi0_out>;
+ };
+ };
+ };
+
+ };
+};
+
+&dsi0_out {
+ remote-endpoint = <&panel_in>;
+ data-lanes = <0 1 2 3>;
+};
+
+&dsi_phy0 {
+ vddio-supply = <&pm8916_l16>;
+ qcom,dsi-phy-regulator-ldo-mode;
+ status = "okay";
+};
+
+&tlmm {
+ ak8963_default: ak8963-default-state {
+ pins = "gpio69";
+ function = "gpio";
+ drive-strength = <6>;
+ bias-pull-up;
+ };
+
+ ak8963_sleep: ak8963-sleep-state {
+ pins = "gpio69";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ /* Ambient light and proximity sensor apds9930 and apds9900 */
+ apds99xx_default: apds99xx-default-state {
+ pins = "gpio113";
+ function = "gpio";
+ drive-strength = <6>;
+ bias-pull-up;
+ };
+
+ apds99xx_sleep: apds99xx-sleep-state {
+ pins = "gpio113";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ cam_sensor_flash_default: cam-sensor-flash-default-state {
+ pins = "gpio98", "gpio97";
+ function = "gpio";
+ bias-disable;
+ drive-strength = <2>;
+ };
+
+ cci1_default: cci1-default-state {
+ pins = "gpio31", "gpio32";
+ function = "cci_i2c";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ cdc_ext_spk_pa_active: cdc-ext-spk-pa-on-state {
+ pins = "gpio0";
+ function = "gpio";
+ drive-strength = <8>;
+ output-low;
+ };
+
+ cdc_ext_spk_pa_sus: cdc-ext-spk-pa-off-state {
+ pins = "gpio0";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ cdc_slim_lines_act: lines-on-state {
+ pins = "gpio63";
+ function = "cdc_pdm0";
+ drive-strength = <8>;
+ output-high;
+ };
+
+ cdc_slim_lines_sus: lines-off-state {
+ pins = "gpio63";
+ function = "cdc_pdm0";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ cross_conn_det_act: lines-on-state {
+ pins = "gpio120";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-pull-down;
+ output-low;
+ };
+
+ cross_conn_det_sus: lines-off-state {
+ pins = "gpio120";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ ext_buck_vsel: vsel0-state {
+ pins = "gpio111";
+ function = "gpio";
+ drive-strength = <2>;
+ };
+
+ ext_cdc_tlmm_lines_act: tlmm-lines-on-state {
+ pins = "gpio116", "gpio112", "gpio117", "gpio118", "gpio119";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-disable;
+ };
+
+ ext_cdc_tlmm_lines_sus: tlmm-lines-off-state {
+ pins = "gpio116", "gpio112", "gpio117", "gpio118", "gpio119";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ gpio_key_suspend: gpio-key-suspend-state {
+ pins = "gpio107", "gpio108", "gpio109";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ negative5_reg_default: negative5-reg-default-state {
+ pins = "gpio17";
+ function = "gpio";
+ output-low;
+ };
+
+ positive5_reg_default: positive5-reg-default-state {
+ pins = "gpio114";
+ function = "gpio";
+ output-low;
+ };
+
+ /* Gyroscope and accelerometer sensor combo */
+ mpu6050_default: mpu6050-default-state {
+ pins = "gpio115";
+ function = "gpio";
+ drive-strength = <6>;
+ bias-pull-up;
+ };
+
+ mpu6050_sleep: mpu6050-sleep-state {
+ pins = "gpio115";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ nfc_disable_active: nfc-disable-active-state {
+ pins = "gpio20";
+ function = "gpio";
+ drive-strength = <6>;
+ bias-pull-up;
+ };
+
+ nfc_disable_suspend: nfc-disable-suspend-state {
+ pins = "gpio20";
+ function = "gpio";
+ drive-strength = <6>;
+ bias-disable;
+ };
+
+ nfc_int_active: nfc-int-active-state {
+ pins = "gpio21";
+ function = "gpio";
+ drive-strength = <6>;
+ bias-pull-up;
+ };
+
+ nfc_int_suspend: nfc-int-suspend-state {
+ pins = "gpio21";
+ function = "gpio";
+ drive-strength = <6>;
+ bias-pull-up;
+ };
+
+ nt35521_te_default: nt35521-te-default-state {
+ pins = "gpio24";
+ function = "gpio";
+ drive-strength = <6>;
+ bias-pull-down;
+ };
+
+ nt35521_backlight: nt35521-backlight-default-state {
+ pins = "gpio10";
+ function = "gpio";
+ drive-strength = <6>;
+ bias-pull-down;
+ };
+
+ smb_int: smb-int-default-state {
+ pins = "gpio62";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ ts_int_active: ts-int-active-state {
+ pins = "gpio13";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-pull-up;
+ };
+
+ ts_int_suspend: ts-int-suspend-state {
+ pins = "gpio13";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ ts_reset_active: ts-reset-active-state {
+ pins = "gpio12";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-pull-up;
+ };
+
+ ts_reset_suspend: ts-reset-suspend-state {
+ pins = "gpio12";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ ts_release: ts-release-default-state {
+ pins = "gpio13", "gpio12";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ usb_id_default: usb-id-default-state {
+ pins = "gpio110";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+};
+
+&pronto {
+ status = "okay";
+
+ iris {
+ compatible = "qcom,wcn3660";
+ };
+};
+
+&smd_rpm_regulators {
+ vdd_l1_l2_l3-supply = <&pm8916_s3>;
+ vdd_l4_l5_l6-supply = <&pm8916_s4>;
+ vdd_l7-supply = <&pm8916_s4>;
+
+ pm8916_s3: s3 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1300000>;
+ };
+
+ pm8916_s4: s4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2100000>;
+ };
+
+ pm8916_l2: l2 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ pm8916_l4: l4 {
+ regulator-min-microvolt = <2050000>;
+ regulator-max-microvolt = <2050000>;
+ };
+
+ pm8916_l5: l5 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ pm8916_l6: l6 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ pm8916_l7: l7 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ pm8916_l8: l8 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2900000>;
+ };
+
+ pm8916_l9: l9 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ pm8916_l10: l10 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ pm8916_l11: l11 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-allow-set-load;
+ regulator-system-load = <200000>;
+ };
+
+ pm8916_l12: l12 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ pm8916_l13: l13 {
+ regulator-min-microvolt = <3075000>;
+ regulator-max-microvolt = <3075000>;
+ };
+
+ pm8916_l14: l14 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ pm8916_l15: l15 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ pm8916_l16: l16 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ pm8916_l17: l17 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ };
+
+ pm8916_l18: l18 {
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2700000>;
+ };
+};
+
+&sdhc_1 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&sdc1_default_state>;
+ pinctrl-1 = <&sdc1_sleep_state>;
+ status = "okay";
+};
+
+&sdhc_2 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&sdc2_default_state>;
+ pinctrl-1 = <&sdc2_sleep_state>;
+ cd-gpios = <&tlmm 38 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+};
+
+&usb {
+ extcon = <&usb_id>, <&usb_id>;
+ status = "okay";
+
+ ulpi {
+ usb_hs_phy: phy {
+ v1p8-supply = <&pm8916_l7>;
+ v3p3-supply = <&pm8916_l13>;
+ };
+ };
+};
+
+&usb_hs_phy {
+ extcon = <&usb_id>;
+};
--
2.38.1
^ permalink raw reply related [flat|nested] 32+ messages in thread
* Re: [PATCH v3 3/8] dt-bindings: interconnect: Exclude all non msm8939 from snoc-mm
2023-01-17 2:48 ` [PATCH v3 3/8] dt-bindings: interconnect: Exclude all non msm8939 from snoc-mm Bryan O'Donoghue
@ 2023-01-17 11:04 ` Krzysztof Kozlowski
0 siblings, 0 replies; 32+ messages in thread
From: Krzysztof Kozlowski @ 2023-01-17 11:04 UTC (permalink / raw)
To: Bryan O'Donoghue, agross, andersson, konrad.dybcio, djakov,
robh+dt, krzysztof.kozlowski+dt
Cc: linux-arm-msm, linux-pm, devicetree, linux-kernel, benl,
shawn.guo, fabien.parent, leo.yan, dmitry.baryshkov
On 17/01/2023 03:48, Bryan O'Donoghue wrote:
> New properties should be defined before the allOf. Move the
> patternProperties definition to before the additionalProperties: false in
> this file.
>
> Exclude all non msm8939 compats from containing a matching
> patternProperties.
>
> Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
> ---
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Best regards,
Krzysztof
^ permalink raw reply [flat|nested] 32+ messages in thread
* Re: [PATCH v3 5/8] arm64: dts: qcom: Add msm8939 SoC
2023-01-17 2:48 ` [PATCH v3 5/8] arm64: dts: qcom: Add msm8939 SoC Bryan O'Donoghue
@ 2023-01-17 20:58 ` Bjorn Andersson
2023-01-17 22:48 ` Bryan O'Donoghue
2023-01-20 0:40 ` Bryan O'Donoghue
2023-01-18 9:59 ` Stephan Gerhold
1 sibling, 2 replies; 32+ messages in thread
From: Bjorn Andersson @ 2023-01-17 20:58 UTC (permalink / raw)
To: Bryan O'Donoghue
Cc: agross, konrad.dybcio, djakov, robh+dt, krzysztof.kozlowski+dt,
linux-arm-msm, linux-pm, devicetree, linux-kernel, benl,
shawn.guo, fabien.parent, leo.yan, dmitry.baryshkov, Jun Nie,
James Willcox, Joseph Gates, Max Chen, Zac Crosby,
Vincent Knecht, Stephan Gerhold
On Tue, Jan 17, 2023 at 02:48:43AM +0000, Bryan O'Donoghue wrote:
> Add msm8939 a derivative SoC of msm8916. This SoC contains a number of key
> differences to msm8916.
>
> - big.LITTLE Octa Core - quad 1.5GHz + quad 1.0GHz
> - DRAM 1x800 LPDDR3
> - Camera 4+4 lane CSI
> - Venus @ 1080p60 HEVC
> - DSI x 2
> - Adreno A405
> - WiFi wcn3660/wcn3680b 802.11ac
>
> Co-developed-by: Shawn Guo <shawn.guo@linaro.org>
> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
> Co-developed-by: Jun Nie <jun.nie@linaro.org>
> Signed-off-by: Jun Nie <jun.nie@linaro.org>
> Co-developed-by: Benjamin Li <benl@squareup.com>
> Signed-off-by: Benjamin Li <benl@squareup.com>
> Co-developed-by: James Willcox <jwillcox@squareup.com>
> Signed-off-by: James Willcox <jwillcox@squareup.com>
> Co-developed-by: Leo Yan <leo.yan@linaro.org>
> Signed-off-by: Leo Yan <leo.yan@linaro.org>
> Co-developed-by: Joseph Gates <jgates@squareup.com>
> Signed-off-by: Joseph Gates <jgates@squareup.com>
> Co-developed-by: Max Chen <mchen@squareup.com>
> Signed-off-by: Max Chen <mchen@squareup.com>
> Co-developed-by: Zac Crosby <zac@squareup.com>
> Signed-off-by: Zac Crosby <zac@squareup.com>
> Co-developed-by: Vincent Knecht <vincent.knecht@mailoo.org>
> Signed-off-by: Vincent Knecht <vincent.knecht@mailoo.org>
> Co-developed-by: Stephan Gerhold <stephan@gerhold.net>
> Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
> Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Just to make sure when I get the question, you all co-developed this
patch, right?
> ---
> arch/arm64/boot/dts/qcom/msm8939.dtsi | 2393 +++++++++++++++++++++++++
> 1 file changed, 2393 insertions(+)
> create mode 100644 arch/arm64/boot/dts/qcom/msm8939.dtsi
>
> diff --git a/arch/arm64/boot/dts/qcom/msm8939.dtsi b/arch/arm64/boot/dts/qcom/msm8939.dtsi
> new file mode 100644
> index 0000000000000..8cd358a9fe623
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/msm8939.dtsi
> @@ -0,0 +1,2393 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * Copyright (c) 2013-2015, The Linux Foundation. All rights reserved.
> + * Copyright (c) 2020-2023, Linaro Limited
> + */
> +
> +#include <dt-bindings/clock/qcom,gcc-msm8939.h>
> +#include <dt-bindings/clock/qcom,rpmcc.h>
> +#include <dt-bindings/interconnect/qcom,msm8939.h>
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/power/qcom-rpmpd.h>
> +#include <dt-bindings/reset/qcom,gcc-msm8939.h>
> +#include <dt-bindings/thermal/thermal.h>
> +
> +/ {
> + interrupt-parent = <&intc>;
> +
> + #address-cells = <2>;
> + #size-cells = <2>;
Why do you use a default of 2? In particular since you reduce it to 1 in
/soc...
> +
> + clocks {
> + xo_board: xo-board {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <19200000>;
> + };
> +
> + sleep_clk: sleep-clk {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <32768>;
> + };
> + };
[..]
> + smp2p-hexagon {
To avoid having people start sending patches that changes the sort order
as soon as I merge this, could you please sort your nodes by address
(not applicable for this one), then by node name alphabetically, then by
label alphabetically.
> + compatible = "qcom,smp2p";
> + qcom,smem = <435>, <428>;
> +
> + interrupts = <GIC_SPI 27 IRQ_TYPE_EDGE_RISING>;
> +
> + mboxes = <&apcs1_mbox 14>;
> +
> + qcom,local-pid = <0>;
> + qcom,remote-pid = <1>;
> +
> + hexagon_smp2p_out: master-kernel {
> + qcom,entry-name = "master-kernel";
> +
> + #qcom,smem-state-cells = <1>;
> + };
> +
> + hexagon_smp2p_in: slave-kernel {
> + qcom,entry-name = "slave-kernel";
> +
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + #address-cells = <0>;
> + #size-cells = <0>;
> + };
> + };
> +
> + memory@80000000 {
> + device_type = "memory";
> + /* We expect the bootloader to fill in the reg */
> + reg = <0x0 0x80000000 0x0 0x0>;
> + };
> +
[..]
> + soc: soc@0 {
[..]
> + pronto: remoteproc@a204000 {
> + compatible = "qcom,pronto-v2-pil", "qcom,pronto";
> + reg = <0x0a204000 0x2000>,
> + <0x0a202000 0x1000>,
> + <0x0a21b000 0x3000>;
> + reg-names = "ccu", "dxe", "pmu";
> +
> + interrupts-extended = <&intc 0 149 IRQ_TYPE_EDGE_RISING>,
> + <&wcnss_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
> + <&wcnss_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
> + <&wcnss_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
> + <&wcnss_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
> + interrupt-names = "wdog", "fatal", "ready", "handover", "stop-ack";
> +
> + memory-region = <&wcnss_mem>;
> +
> + power-domains = <&rpmpd MSM8939_VDDCX>,
> + <&rpmpd MSM8939_VDDMX_AO>;
The purpose of the remoteproc driver's vote is to keep the rails powered
while we're booting the remote, in the event that Linux decides to
suspend and turn of the power rails while we're waiting...
Once the remote pulls the "handover" interrupt, it signals that it has
cast the necessary votes and need no more hand-holding.
So it's unlikely that _AO is the right choice here.
> + power-domain-names = "cx", "mx";
> +
> + qcom,smem-states = <&wcnss_smp2p_out 0>;
> + qcom,smem-state-names = "stop";
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&wcnss_pin_a>;
> +
> + status = "disabled";
> +
> + iris {
> + compatible = "qcom,wcn3620";
> + clocks = <&rpmcc RPM_SMD_RF_CLK2>;
> + clock-names = "xo";
> + };
> +
> + smd-edge {
> + interrupts = <GIC_SPI 142 1>;
> + qcom,ipc = <&apcs1_mbox 8 17>;
> + qcom,smd-edge = <6>;
> + qcom,remote-pid = <4>;
> +
> + label = "pronto";
> +
> + wcnss {
> + compatible = "qcom,wcnss";
> + qcom,smd-channels = "WCNSS_CTRL";
> +
> + qcom,mmio = <&pronto>;
> +
> + bluetooth {
> + compatible = "qcom,wcnss-bt";
> + };
> +
> + wifi {
> + compatible = "qcom,wcnss-wlan";
> +
> + interrupts = <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "tx", "rx";
> +
> + qcom,smem-states = <&apps_smsm 10>,
> + <&apps_smsm 9>;
> + qcom,smem-state-names = "tx-enable",
> + "tx-rings-empty";
> + };
> + };
> + };
> + };
> + };
> +
> + smd {
"so" < "sm"
> + compatible = "qcom,smd";
> +
> + rpm {
> + interrupts = <GIC_SPI 168 IRQ_TYPE_EDGE_RISING>;
> + qcom,ipc = <&apcs1_mbox 8 0>;
> + qcom,smd-edge = <15>;
> +
> + rpm_requests: rpm-requests {
> + compatible = "qcom,rpm-msm8936";
> + qcom,smd-channels = "rpm_requests";
> +
> + rpmcc: clock-controller {
> + compatible = "qcom,rpmcc-msm8936", "qcom,rpmcc";
> + #clock-cells = <1>;
> + clock-names = "xo";
> + clocks = <&xo_board>;
> + };
> +
> + rpmpd: power-controller {
> + compatible = "qcom,msm8939-rpmpd";
> + #power-domain-cells = <1>;
> + operating-points-v2 = <&rpmpd_opp_table>;
> +
> + rpmpd_opp_table: opp-table {
> + compatible = "operating-points-v2";
> +
> + rpmpd_opp_ret: opp1 {
> + opp-level = <1>;
> + };
> +
> + rpmpd_opp_svs_krait: opp2 {
> + opp-level = <2>;
> + };
> +
> + rpmpd_opp_svs_soc: opp3 {
> + opp-level = <3>;
> + };
> +
> + rpmpd_opp_nom: opp4 {
> + opp-level = <4>;
> + };
> +
> + rpmpd_opp_turbo: opp5 {
> + opp-level = <5>;
> + };
> +
> + rpmpd_opp_super_turbo: opp6 {
> + opp-level = <6>;
> + };
> + };
> + };
> + };
> + };
> + };
[..]
> +
> + /* Dummy regulator for our non-psci cpu@X defintions */
It's a power-supply...
> + vreg_dummy: regulator-dummy {
> + #power-domain-cells = <0>;
> + };
> +
> + smp2p-wcnss {
This belongs up by the other smp2p node.
Regards,
Bjorn
^ permalink raw reply [flat|nested] 32+ messages in thread
* Re: [PATCH v3 7/8] arm64: dts: qcom: Add Square apq8039-t2 board
2023-01-17 2:48 ` [PATCH v3 7/8] arm64: dts: qcom: Add Square apq8039-t2 board Bryan O'Donoghue
@ 2023-01-17 21:06 ` Bjorn Andersson
0 siblings, 0 replies; 32+ messages in thread
From: Bjorn Andersson @ 2023-01-17 21:06 UTC (permalink / raw)
To: Bryan O'Donoghue
Cc: agross, konrad.dybcio, djakov, robh+dt, krzysztof.kozlowski+dt,
linux-arm-msm, linux-pm, devicetree, linux-kernel, benl,
shawn.guo, fabien.parent, leo.yan, dmitry.baryshkov, Jun Nie,
James Willcox, Joseph Gates, Max Chen, Zac Crosby
On Tue, Jan 17, 2023 at 02:48:45AM +0000, Bryan O'Donoghue wrote:
> The apq8039-t2 is an apq8039 based board paired with a wcn3680b WiFi
> chipset.
>
> Co-developed-by: Shawn Guo <shawn.guo@linaro.org>
> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
> Co-developed-by: Jun Nie <jun.nie@linaro.org>
> Signed-off-by: Jun Nie <jun.nie@linaro.org>
> Co-developed-by: Benjamin Li <benl@squareup.com>
> Signed-off-by: Benjamin Li <benl@squareup.com>
> Co-developed-by: James Willcox <jwillcox@squareup.com>
> Signed-off-by: James Willcox <jwillcox@squareup.com>
> Co-developed-by: Leo Yan <leo.yan@linaro.org>
> Signed-off-by: Leo Yan <leo.yan@linaro.org>
> Co-developed-by: Joseph Gates <jgates@squareup.com>
> Signed-off-by: Joseph Gates <jgates@squareup.com>
> Co-developed-by: Max Chen <mchen@squareup.com>
> Signed-off-by: Max Chen <mchen@squareup.com>
> Co-developed-by: Zac Crosby <zac@squareup.com>
> Signed-off-by: Zac Crosby <zac@squareup.com>
> Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
> ---
> arch/arm64/boot/dts/qcom/Makefile | 1 +
> arch/arm64/boot/dts/qcom/apq8039-t2.dts | 557 ++++++++++++++++++++++++
> 2 files changed, 558 insertions(+)
> create mode 100644 arch/arm64/boot/dts/qcom/apq8039-t2.dts
>
> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
> index e442a81895d04..5c47d1fb50b01 100644
> --- a/arch/arm64/boot/dts/qcom/Makefile
> +++ b/arch/arm64/boot/dts/qcom/Makefile
> @@ -1,5 +1,6 @@
> # SPDX-License-Identifier: GPL-2.0
> dtb-$(CONFIG_ARCH_QCOM) += apq8016-sbc.dtb
> +dtb-$(CONFIG_ARCH_QCOM) += apq8039-t2.dtb
> dtb-$(CONFIG_ARCH_QCOM) += apq8094-sony-xperia-kitakami-karin_windy.dtb
> dtb-$(CONFIG_ARCH_QCOM) += apq8096-db820c.dtb
> dtb-$(CONFIG_ARCH_QCOM) += apq8096-ifc6640.dtb
> diff --git a/arch/arm64/boot/dts/qcom/apq8039-t2.dts b/arch/arm64/boot/dts/qcom/apq8039-t2.dts
> new file mode 100644
> index 0000000000000..21f5a21f76135
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/apq8039-t2.dts
> @@ -0,0 +1,557 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (c) 2015, The Linux Foundation. All rights reserved.
> + * Copyright (c) 2020-2023, Linaro Ltd.
> + *
> + */
> +
> +/dts-v1/;
> +
> +#include "msm8939.dtsi"
> +#include "msm8939-pm8916.dtsi"
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
> +#include <dt-bindings/sound/apq8016-lpass.h>
> +
> +/ {
> + model = "Square, Inc. T2 Devkit";
> + compatible = "square,apq8039-t2", "qcom,msm8939";
> +
> + qcom,board-id = <0x53 0x54>;
> + qcom,msm-id = <239 0>, <239 0x30000>, <241 0x30000>, <263 0x30000>;
Would it be possible to include and use dt-bindings/arm/qcom,ids.h here?
> +
> + aliases {
> + mmc0 = &sdhc_1;
> + mmc1 = &sdhc_2;
> + serial0 = &blsp1_uart1;
> + serial1 = &blsp1_uart2;
> + };
[..]
> +&pm8916_gpios {
> + gpio-line-names =
> + "PM_GPIO1", /* WIFI_GPIO1_PRE */
> + "PM_GPIO2", /* WIFI_GPIO2_PRE */
> + "PM_GPIO3",
> + "PM_GPIO4";
> +};
> +
> +&pronto {
As mentioned in the dtsi patch, please sort your nodes by label,
alphabetically. You may choose to group the pinctrl nodes last in the
file...
Regards,
Bjorn
> + pinctrl-names = "default";
> + pinctrl-0 = <&wcnss_pin_a>;
> + status = "okay";
> +
> + iris {
> + compatible = "qcom,wcn3680";
> + };
> +};
^ permalink raw reply [flat|nested] 32+ messages in thread
* Re: [PATCH v3 5/8] arm64: dts: qcom: Add msm8939 SoC
2023-01-17 20:58 ` Bjorn Andersson
@ 2023-01-17 22:48 ` Bryan O'Donoghue
2023-01-18 5:09 ` Bjorn Andersson
2023-01-20 0:40 ` Bryan O'Donoghue
1 sibling, 1 reply; 32+ messages in thread
From: Bryan O'Donoghue @ 2023-01-17 22:48 UTC (permalink / raw)
To: Bjorn Andersson
Cc: agross, konrad.dybcio, djakov, robh+dt, krzysztof.kozlowski+dt,
linux-arm-msm, linux-pm, devicetree, linux-kernel, benl,
shawn.guo, fabien.parent, leo.yan, dmitry.baryshkov, Jun Nie,
James Willcox, Joseph Gates, Max Chen, Zac Crosby,
Vincent Knecht, Stephan Gerhold
On 17/01/2023 20:58, Bjorn Andersson wrote:
> On Tue, Jan 17, 2023 at 02:48:43AM +0000, Bryan O'Donoghue wrote:
>> Add msm8939 a derivative SoC of msm8916. This SoC contains a number of key
>> differences to msm8916.
>>
>> - big.LITTLE Octa Core - quad 1.5GHz + quad 1.0GHz
>> - DRAM 1x800 LPDDR3
>> - Camera 4+4 lane CSI
>> - Venus @ 1080p60 HEVC
>> - DSI x 2
>> - Adreno A405
>> - WiFi wcn3660/wcn3680b 802.11ac
>>
>> Co-developed-by: Shawn Guo <shawn.guo@linaro.org>
>> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
>> Co-developed-by: Jun Nie <jun.nie@linaro.org>
>> Signed-off-by: Jun Nie <jun.nie@linaro.org>
>> Co-developed-by: Benjamin Li <benl@squareup.com>
>> Signed-off-by: Benjamin Li <benl@squareup.com>
>> Co-developed-by: James Willcox <jwillcox@squareup.com>
>> Signed-off-by: James Willcox <jwillcox@squareup.com>
>> Co-developed-by: Leo Yan <leo.yan@linaro.org>
>> Signed-off-by: Leo Yan <leo.yan@linaro.org>
>> Co-developed-by: Joseph Gates <jgates@squareup.com>
>> Signed-off-by: Joseph Gates <jgates@squareup.com>
>> Co-developed-by: Max Chen <mchen@squareup.com>
>> Signed-off-by: Max Chen <mchen@squareup.com>
>> Co-developed-by: Zac Crosby <zac@squareup.com>
>> Signed-off-by: Zac Crosby <zac@squareup.com>
>> Co-developed-by: Vincent Knecht <vincent.knecht@mailoo.org>
>> Signed-off-by: Vincent Knecht <vincent.knecht@mailoo.org>
>> Co-developed-by: Stephan Gerhold <stephan@gerhold.net>
>> Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
>> Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
>
> Just to make sure when I get the question, you all co-developed this
> patch, right?
A long list but a fair one.
>> ---
>> arch/arm64/boot/dts/qcom/msm8939.dtsi | 2393 +++++++++++++++++++++++++
>> 1 file changed, 2393 insertions(+)
>> create mode 100644 arch/arm64/boot/dts/qcom/msm8939.dtsi
>>
>> diff --git a/arch/arm64/boot/dts/qcom/msm8939.dtsi b/arch/arm64/boot/dts/qcom/msm8939.dtsi
>> new file mode 100644
>> index 0000000000000..8cd358a9fe623
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/qcom/msm8939.dtsi
>> @@ -0,0 +1,2393 @@
>> +// SPDX-License-Identifier: GPL-2.0-only
>> +/*
>> + * Copyright (c) 2013-2015, The Linux Foundation. All rights reserved.
>> + * Copyright (c) 2020-2023, Linaro Limited
>> + */
>> +
>> +#include <dt-bindings/clock/qcom,gcc-msm8939.h>
>> +#include <dt-bindings/clock/qcom,rpmcc.h>
>> +#include <dt-bindings/interconnect/qcom,msm8939.h>
>> +#include <dt-bindings/interrupt-controller/arm-gic.h>
>> +#include <dt-bindings/power/qcom-rpmpd.h>
>> +#include <dt-bindings/reset/qcom,gcc-msm8939.h>
>> +#include <dt-bindings/thermal/thermal.h>
>> +
>> +/ {
>> + interrupt-parent = <&intc>;
>> +
>> + #address-cells = <2>;
>> + #size-cells = <2>;
>
> Why do you use a default of 2? In particular since you reduce it to 1 in
> /soc...
You asked that before, and I took a note of the answer but, then because
I was away from the main machine when I sent V2, I didn't have the log.
Here's what I wrote down.
" - address-cells/size-cells = 1 in /soc - Bjorn
I experimentally changed address/cell sizes to 2
I'm finding that lk chokes "
So AFAIR LK was unhappy about changing the top level address/size cells
to <1> <1> and converting the /soc address/size cells to <2> <2> caused
a number of breakages during boot.
To be honest, this pattern is copied from the msm8916.dtsi original.
msm8953.dtsi has the same thing. msm8994 too, and 8998.
If you think it needs changing, then I'll have to see what can be done
with soc@{} entries.
>
>> +
>> + clocks {
>> + xo_board: xo-board {
>> + compatible = "fixed-clock";
>> + #clock-cells = <0>;
>> + clock-frequency = <19200000>;
>> + };
>> +
>> + sleep_clk: sleep-clk {
>> + compatible = "fixed-clock";
>> + #clock-cells = <0>;
>> + clock-frequency = <32768>;
>> + };
>> + };
> [..]
>> + smp2p-hexagon {
>
> To avoid having people start sending patches that changes the sort order
> as soon as I merge this, could you please sort your nodes by address
> (not applicable for this one), then by node name alphabetically, then by
> label alphabetically.
ah. I sorted the contents of soc. I missed the upper level groupings.
>
>> + compatible = "qcom,smp2p";
>> + qcom,smem = <435>, <428>;
>> +
>> + interrupts = <GIC_SPI 27 IRQ_TYPE_EDGE_RISING>;
>> +
>> + mboxes = <&apcs1_mbox 14>;
>> +
>> + qcom,local-pid = <0>;
>> + qcom,remote-pid = <1>;
>> +
>> + hexagon_smp2p_out: master-kernel {
>> + qcom,entry-name = "master-kernel";
>> +
>> + #qcom,smem-state-cells = <1>;
>> + };
>> +
>> + hexagon_smp2p_in: slave-kernel {
>> + qcom,entry-name = "slave-kernel";
>> +
>> + interrupt-controller;
>> + #interrupt-cells = <2>;
>> + #address-cells = <0>;
>> + #size-cells = <0>;
>> + };
>> + };
>> +
>> + memory@80000000 {
>> + device_type = "memory";
>> + /* We expect the bootloader to fill in the reg */
>> + reg = <0x0 0x80000000 0x0 0x0>;
>> + };
>> +
> [..]
>> + soc: soc@0 {
> [..]
>> + pronto: remoteproc@a204000 {
>> + compatible = "qcom,pronto-v2-pil", "qcom,pronto";
>> + reg = <0x0a204000 0x2000>,
>> + <0x0a202000 0x1000>,
>> + <0x0a21b000 0x3000>;
>> + reg-names = "ccu", "dxe", "pmu";
>> +
>> + interrupts-extended = <&intc 0 149 IRQ_TYPE_EDGE_RISING>,
>> + <&wcnss_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
>> + <&wcnss_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
>> + <&wcnss_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
>> + <&wcnss_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
>> + interrupt-names = "wdog", "fatal", "ready", "handover", "stop-ack";
>> +
>> + memory-region = <&wcnss_mem>;
>> +
>> + power-domains = <&rpmpd MSM8939_VDDCX>,
>> + <&rpmpd MSM8939_VDDMX_AO>;
>
> The purpose of the remoteproc driver's vote is to keep the rails powered
> while we're booting the remote, in the event that Linux decides to
> suspend and turn of the power rails while we're waiting...
>
> Once the remote pulls the "handover" interrupt, it signals that it has
> cast the necessary votes and need no more hand-holding.
>
> So it's unlikely that _AO is the right choice here.
Yes, it's probably just VDDMX isn't it.
I'll change that.
---
bod
^ permalink raw reply [flat|nested] 32+ messages in thread
* Re: [PATCH v3 5/8] arm64: dts: qcom: Add msm8939 SoC
2023-01-17 22:48 ` Bryan O'Donoghue
@ 2023-01-18 5:09 ` Bjorn Andersson
0 siblings, 0 replies; 32+ messages in thread
From: Bjorn Andersson @ 2023-01-18 5:09 UTC (permalink / raw)
To: Bryan O'Donoghue
Cc: agross, konrad.dybcio, djakov, robh+dt, krzysztof.kozlowski+dt,
linux-arm-msm, linux-pm, devicetree, linux-kernel, benl,
shawn.guo, fabien.parent, leo.yan, dmitry.baryshkov, Jun Nie,
James Willcox, Joseph Gates, Max Chen, Zac Crosby,
Vincent Knecht, Stephan Gerhold
On Tue, Jan 17, 2023 at 10:48:37PM +0000, Bryan O'Donoghue wrote:
> On 17/01/2023 20:58, Bjorn Andersson wrote:
> > On Tue, Jan 17, 2023 at 02:48:43AM +0000, Bryan O'Donoghue wrote:
> > > Add msm8939 a derivative SoC of msm8916. This SoC contains a number of key
> > > differences to msm8916.
> > >
> > > - big.LITTLE Octa Core - quad 1.5GHz + quad 1.0GHz
> > > - DRAM 1x800 LPDDR3
> > > - Camera 4+4 lane CSI
> > > - Venus @ 1080p60 HEVC
> > > - DSI x 2
> > > - Adreno A405
> > > - WiFi wcn3660/wcn3680b 802.11ac
> > >
> > > Co-developed-by: Shawn Guo <shawn.guo@linaro.org>
> > > Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
> > > Co-developed-by: Jun Nie <jun.nie@linaro.org>
> > > Signed-off-by: Jun Nie <jun.nie@linaro.org>
> > > Co-developed-by: Benjamin Li <benl@squareup.com>
> > > Signed-off-by: Benjamin Li <benl@squareup.com>
> > > Co-developed-by: James Willcox <jwillcox@squareup.com>
> > > Signed-off-by: James Willcox <jwillcox@squareup.com>
> > > Co-developed-by: Leo Yan <leo.yan@linaro.org>
> > > Signed-off-by: Leo Yan <leo.yan@linaro.org>
> > > Co-developed-by: Joseph Gates <jgates@squareup.com>
> > > Signed-off-by: Joseph Gates <jgates@squareup.com>
> > > Co-developed-by: Max Chen <mchen@squareup.com>
> > > Signed-off-by: Max Chen <mchen@squareup.com>
> > > Co-developed-by: Zac Crosby <zac@squareup.com>
> > > Signed-off-by: Zac Crosby <zac@squareup.com>
> > > Co-developed-by: Vincent Knecht <vincent.knecht@mailoo.org>
> > > Signed-off-by: Vincent Knecht <vincent.knecht@mailoo.org>
> > > Co-developed-by: Stephan Gerhold <stephan@gerhold.net>
> > > Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
> > > Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
> >
> > Just to make sure when I get the question, you all co-developed this
> > patch, right?
>
> A long list but a fair one.
>
> > > ---
> > > arch/arm64/boot/dts/qcom/msm8939.dtsi | 2393 +++++++++++++++++++++++++
> > > 1 file changed, 2393 insertions(+)
> > > create mode 100644 arch/arm64/boot/dts/qcom/msm8939.dtsi
> > >
> > > diff --git a/arch/arm64/boot/dts/qcom/msm8939.dtsi b/arch/arm64/boot/dts/qcom/msm8939.dtsi
> > > new file mode 100644
> > > index 0000000000000..8cd358a9fe623
> > > --- /dev/null
> > > +++ b/arch/arm64/boot/dts/qcom/msm8939.dtsi
> > > @@ -0,0 +1,2393 @@
> > > +// SPDX-License-Identifier: GPL-2.0-only
> > > +/*
> > > + * Copyright (c) 2013-2015, The Linux Foundation. All rights reserved.
> > > + * Copyright (c) 2020-2023, Linaro Limited
> > > + */
> > > +
> > > +#include <dt-bindings/clock/qcom,gcc-msm8939.h>
> > > +#include <dt-bindings/clock/qcom,rpmcc.h>
> > > +#include <dt-bindings/interconnect/qcom,msm8939.h>
> > > +#include <dt-bindings/interrupt-controller/arm-gic.h>
> > > +#include <dt-bindings/power/qcom-rpmpd.h>
> > > +#include <dt-bindings/reset/qcom,gcc-msm8939.h>
> > > +#include <dt-bindings/thermal/thermal.h>
> > > +
> > > +/ {
> > > + interrupt-parent = <&intc>;
> > > +
> > > + #address-cells = <2>;
> > > + #size-cells = <2>;
> >
> > Why do you use a default of 2? In particular since you reduce it to 1 in
> > /soc...
>
> You asked that before, and I took a note of the answer but, then because I
> was away from the main machine when I sent V2, I didn't have the log.
>
> Here's what I wrote down.
>
> " - address-cells/size-cells = 1 in /soc - Bjorn
> I experimentally changed address/cell sizes to 2
> I'm finding that lk chokes "
>
> So AFAIR LK was unhappy about changing the top level address/size cells to
> <1> <1> and converting the /soc address/size cells to <2> <2> caused a
> number of breakages during boot.
>
> To be honest, this pattern is copied from the msm8916.dtsi original.
> msm8953.dtsi has the same thing. msm8994 too, and 8998.
>
> If you think it needs changing, then I'll have to see what can be done with
> soc@{} entries.
>
Sounds like problems not worth pursuing further. How about leaving a
comment for the next person here about LK's expectation of these being
2?
Thanks,
Bjorn
^ permalink raw reply [flat|nested] 32+ messages in thread
* Re: [PATCH v3 1/8] dt-bindings: arm: qcom: Document MSM8939 SoC binding
2023-01-17 2:48 ` [PATCH v3 1/8] dt-bindings: arm: qcom: Document MSM8939 SoC binding Bryan O'Donoghue
@ 2023-01-18 8:47 ` Stephan Gerhold
2023-01-18 12:05 ` Bryan O'Donoghue
2023-01-19 0:32 ` Bryan O'Donoghue
0 siblings, 2 replies; 32+ messages in thread
From: Stephan Gerhold @ 2023-01-18 8:47 UTC (permalink / raw)
To: Bryan O'Donoghue
Cc: agross, andersson, konrad.dybcio, djakov, robh+dt,
krzysztof.kozlowski+dt, linux-arm-msm, linux-pm, devicetree,
linux-kernel, benl, shawn.guo, fabien.parent, leo.yan,
dmitry.baryshkov, Krzysztof Kozlowski
On Tue, Jan 17, 2023 at 02:48:39AM +0000, Bryan O'Donoghue wrote:
> Document the MSM8939 and supported boards in upstream Sony "Tulip" M4 Aqua
> and Square APQ8039 T2.
>
> MSM8939 is one of the older SoCs so we need to expand the list of
> qcom,board-ids to allow for the bootloader DTS board-id matching
> dependency.
>
The original LK bootloaders cannot boot your msm8939.dtsi correctly,
because a spin-table implementation is required to get the other CPU
cores up. This means that a modified bootloader is always needed from
the upstream point of view, since I doubt anyone wants to use these
devices with a single core only. lk2nd (as the primary spin-table
implementation right now) has never required qcom,board-ids and any
custom LK would be easy to patch to ignore these.
Do you already have a bootloader with spin-table support deployed in the
field that can be no longer easily modified to ignore the qcom,board-id?
If not, and you're planning to keep using the downstream patches to
bring the CPU cores up without spin-table/PSCI then you might as well
add the qcom,board-id as downstream patch as well.
If we don't support the original bootloaders in a usable way upstream
then we should not add MSM8939 to the allow list of broken bootloaders
either, in my opinion.
Thanks,
Stephan
^ permalink raw reply [flat|nested] 32+ messages in thread
* Re: [PATCH v3 5/8] arm64: dts: qcom: Add msm8939 SoC
2023-01-17 2:48 ` [PATCH v3 5/8] arm64: dts: qcom: Add msm8939 SoC Bryan O'Donoghue
2023-01-17 20:58 ` Bjorn Andersson
@ 2023-01-18 9:59 ` Stephan Gerhold
2023-01-18 11:50 ` Bryan O'Donoghue
2023-01-21 22:57 ` Bryan O'Donoghue
1 sibling, 2 replies; 32+ messages in thread
From: Stephan Gerhold @ 2023-01-18 9:59 UTC (permalink / raw)
To: Bryan O'Donoghue
Cc: agross, andersson, konrad.dybcio, djakov, robh+dt,
krzysztof.kozlowski+dt, linux-arm-msm, linux-pm, devicetree,
linux-kernel, benl, shawn.guo, fabien.parent, leo.yan,
dmitry.baryshkov, Jun Nie, James Willcox, Joseph Gates, Max Chen,
Zac Crosby, Vincent Knecht
On Tue, Jan 17, 2023 at 02:48:43AM +0000, Bryan O'Donoghue wrote:
> Add msm8939 a derivative SoC of msm8916. This SoC contains a number of key
> differences to msm8916.
>
> - big.LITTLE Octa Core - quad 1.5GHz + quad 1.0GHz
> - DRAM 1x800 LPDDR3
> - Camera 4+4 lane CSI
> - Venus @ 1080p60 HEVC
> - DSI x 2
> - Adreno A405
> - WiFi wcn3660/wcn3680b 802.11ac
>
> Co-developed-by: Shawn Guo <shawn.guo@linaro.org>
> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
> Co-developed-by: Jun Nie <jun.nie@linaro.org>
> Signed-off-by: Jun Nie <jun.nie@linaro.org>
> Co-developed-by: Benjamin Li <benl@squareup.com>
> Signed-off-by: Benjamin Li <benl@squareup.com>
> Co-developed-by: James Willcox <jwillcox@squareup.com>
> Signed-off-by: James Willcox <jwillcox@squareup.com>
> Co-developed-by: Leo Yan <leo.yan@linaro.org>
> Signed-off-by: Leo Yan <leo.yan@linaro.org>
> Co-developed-by: Joseph Gates <jgates@squareup.com>
> Signed-off-by: Joseph Gates <jgates@squareup.com>
> Co-developed-by: Max Chen <mchen@squareup.com>
> Signed-off-by: Max Chen <mchen@squareup.com>
> Co-developed-by: Zac Crosby <zac@squareup.com>
> Signed-off-by: Zac Crosby <zac@squareup.com>
> Co-developed-by: Vincent Knecht <vincent.knecht@mailoo.org>
> Signed-off-by: Vincent Knecht <vincent.knecht@mailoo.org>
> Co-developed-by: Stephan Gerhold <stephan@gerhold.net>
> Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
> Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
> ---
> arch/arm64/boot/dts/qcom/msm8939.dtsi | 2393 +++++++++++++++++++++++++
> 1 file changed, 2393 insertions(+)
> create mode 100644 arch/arm64/boot/dts/qcom/msm8939.dtsi
>
> diff --git a/arch/arm64/boot/dts/qcom/msm8939.dtsi b/arch/arm64/boot/dts/qcom/msm8939.dtsi
> new file mode 100644
> index 0000000000000..8cd358a9fe623
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/msm8939.dtsi
> @@ -0,0 +1,2393 @@
> [...]
> + cpus {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + cpu0: cpu@100 {
> + compatible = "arm,cortex-a53";
> + device_type = "cpu";
> + enable-method = "spin-table";
> + reg = <0x100>;
> + next-level-cache = <&L2_1>;
> + power-domains = <&vreg_dummy>;
> + power-domain-names = "cpr";
Why are you adding a dummy power domain here? IMO this would be better
added together with CPR. Especially because I would expect two power
domains here later ("mx", "cpr"). For cpufreq you also need to make
votes for the "MSM8939_VDDMX" power domain.
> + qcom,acc = <&acc0>;
> + qcom,saw = <&saw0>;
> + cpu-idle-states = <&CPU_SLEEP_0>;
> + clocks = <&apcs1_mbox>;
> + #cooling-cells = <2>;
> + L2_1: l2-cache {
> + compatible = "cache";
> + cache-level = <2>;
> + };
> + };
> [...]
> + soc: soc@0 {
> + compatible = "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges = <0 0 0 0xffffffff>;
> +
> + rng@22000 {
> + compatible = "qcom,prng";
> + reg = <0x00022000 0x200>;
> + clocks = <&gcc GCC_PRNG_AHB_CLK>;
> + clock-names = "core";
> + };
> +
> + qfprom: qfprom@5c000 {
> + compatible = "qcom,msm8916-qfprom", "qcom,qfprom";
> + reg = <0x0005c000 0x1000>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + tsens_caldata: caldata@a0 {
> + reg = <0xa0 0x5c>;
> + };
> + cpr_efuse_init_voltage1: ivoltage1@dc {
> + reg = <0xdc 0x4>;
> + bits = <4 6>;
> + };
> + cpr_efuse_init_voltage2: ivoltage2@da {
> + reg = <0xda 0x4>;
> + bits = <2 6>;
> + };
> + cpr_efuse_init_voltage3: ivoltage3@d8 {
> + reg = <0xd8 0x4>;
> + bits = <0 6>;
> + };
> + cpr_efuse_quot1: quot1@dd {
> + reg = <0xdd 0x8>;
> + bits = <2 12>;
> + };
> + cpr_efuse_quot2: quot2@db {
> + reg = <0xdb 0x8>;
> + bits = <0x0 12>;
> + };
> + cpr_efuse_ring1: ring1@de {
> + reg = <0xde 0x4>;
> + bits = <6 3>;
> + };
> + cpr_efuse_revision: revision@5 {
> + reg = <0x5 0x1>;
> + bits = <5 1>;
> + };
> + cpr_efuse_revision_high: revision-high@7 {
> + reg = <0x7 0x1>;
> + bits = <0 1>;
> + };
> + cpr_efuse_pvs_version: pvs@3 {
> + reg = <0x3 0x1>;
> + bits = <5 1>;
> + };
> + cpr_efuse_pvs_version_high: pvs-high@6 {
> + reg = <0x6 0x1>;
> + bits = <2 2>;
> + };
> + cpr_efuse_speedbin: speedbin@c {
> + reg = <0xc 0x1>;
> + bits = <2 3>;
> + };
Please add the CPR items later together with CPR. This will make the
review a bit easier because we don't need to check that these are right
for the initial submission.
> + };
> [...]
> + mdss: display-subsystem@1a00000 {
> + compatible = "qcom,mdss";
> + reg = <0x01a00000 0x1000>,
> + <0x01ac8000 0x3000>;
> + reg-names = "mdss_phys", "vbif_phys";
> +
> + interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-controller;
> +
> + clocks = <&gcc GCC_MDSS_AHB_CLK>,
> + <&gcc GCC_MDSS_AXI_CLK>,
> + <&gcc GCC_MDSS_VSYNC_CLK>;
> + clock-names = "iface",
> + "bus",
> + "vsync";
> +
> + power-domains = <&gcc MDSS_GDSC>;
> +
> + #address-cells = <1>;
> + #size-cells = <1>;
> + #interrupt-cells = <1>;
> + ranges;
> +
> + mdp: display-controller@1a01000 {
> + compatible = "qcom,mdp5";
> + reg = <0x01a01000 0x89000>;
> + reg-names = "mdp_phys";
> +
> + interrupt-parent = <&mdss>;
> + interrupts = <0>;
> +
> + clocks = <&gcc GCC_MDSS_AHB_CLK>,
> + <&gcc GCC_MDSS_AXI_CLK>,
> + <&gcc GCC_MDSS_MDP_CLK>,
> + <&gcc GCC_MDSS_VSYNC_CLK>,
> + <&gcc GCC_MDP_TBU_CLK>,
> + <&gcc GCC_MDP_RT_TBU_CLK>;
> + clock-names = "iface",
> + "bus",
> + "core",
> + "vsync",
> + "tbu",
> + "tbu_rt";
> +
> + iommus = <&apps_iommu 4>;
> +
> + interconnects = <&snoc_mm MASTER_MDP_PORT0 &bimc SLAVE_EBI_CH0>,
> + <&snoc_mm MASTER_MDP_PORT1 &bimc SLAVE_EBI_CH0>,
> + <&pcnoc MASTER_SPDM &snoc SLAVE_IMEM>;
> + interconnect-names = "mdp0-mem", "mdp1-mem", "register-mem";
As I mentioned a already in a direct email at some point, AFAIU adding
interconnects should be an [almost-] all or nothing step. If you only
add interconnects for MDP then everything else that needs bandwidth will
either break or only continue working as a mere side effect of MDP
voting for permanent high bandwidth.
This could break easily if someone has a board without display, or if
the MDP5 driver is optimized to request the minimum necessary bandwidth
only.
I think strictly speaking "interconnects" properties are needed for
everything that uses DMA, i.e. CPUs, SDHCI, USB, UART, I2C, SPI and also
audio (in DSP bypass mode only). If you look at newer platforms they do
have "interconnects" for most of these.
(Semi-related side note: "register-mem" is neither documented nor used
anywhere in the code?)
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> + mdp5_intf1_out: endpoint {
> + remote-endpoint = <&dsi0_in>;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> + mdp5_intf2_out: endpoint {
> + remote-endpoint = <&dsi1_in>;
> + };
> + };
> + };
> + };
> +
> + dsi0: dsi@1a98000 {
> + compatible = "qcom,msm8916-dsi-ctrl",
> + "qcom,mdss-dsi-ctrl";
> + reg = <0x01a98000 0x25c>;
> + reg-names = "dsi_ctrl";
> +
> + interrupt-parent = <&mdss>;
> + interrupts = <4>;
> +
> + power-domains = <&gcc MDSS_GDSC>;
Why is MDSS_GDSC defined again here? The parent-child relationship of
MDSS->MDP should ensure that the MDSS_GDSC from the parent mdss node
is on when dsi is.
> +
> + clocks = <&gcc GCC_MDSS_MDP_CLK>,
> + <&gcc GCC_MDSS_AHB_CLK>,
> + <&gcc GCC_MDSS_AXI_CLK>,
> + <&gcc GCC_MDSS_BYTE0_CLK>,
> + <&gcc GCC_MDSS_PCLK0_CLK>,
> + <&gcc GCC_MDSS_ESC0_CLK>;
> + clock-names = "mdp_core",
> + "iface",
> + "bus",
> + "byte",
> + "pixel",
> + "core";
> + assigned-clocks = <&gcc BYTE0_CLK_SRC>,
> + <&gcc PCLK0_CLK_SRC>;
> + assigned-clock-parents = <&dsi_phy0 0>,
> + <&dsi_phy0 1>;
> +
> + phys = <&dsi_phy0>;
> + status = "disabled";
> +
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> + dsi0_in: endpoint {
> + remote-endpoint = <&mdp5_intf1_out>;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> + dsi0_out: endpoint {
> + };
> + };
> + };
> + };
> +
> + dsi_phy0: phy@1a98300 {
> + compatible = "qcom,dsi-phy-28nm-lp";
> + reg = <0x01a98300 0xd4>,
> + <0x01a98500 0x280>,
> + <0x01a98780 0x30>;
> + reg-names = "dsi_pll",
> + "dsi_phy",
> + "dsi_phy_regulator";
> +
> + clocks = <&gcc GCC_MDSS_AHB_CLK>,
> + <&rpmcc RPM_SMD_XO_CLK_SRC>;
> + clock-names = "iface", "ref";
> +
> + #clock-cells = <1>;
> + #phy-cells = <0>;
> + status = "disabled";
> + };
> +
> + dsi1: dsi@1aa0000 {
> + compatible = "qcom,msm8916-dsi-ctrl",
> + "qcom,mdss-dsi-ctrl";
> + reg = <0x01aa0000 0x25c>;
> + reg-names = "dsi_ctrl";
> +
> + interrupt-parent = <&mdss>;
> + interrupts = <5>;
> +
> + power-domains = <&gcc MDSS_GDSC>;
> +
> + clocks = <&gcc GCC_MDSS_MDP_CLK>,
> + <&gcc GCC_MDSS_AHB_CLK>,
> + <&gcc GCC_MDSS_AXI_CLK>,
> + <&gcc GCC_MDSS_BYTE1_CLK>,
> + <&gcc GCC_MDSS_PCLK1_CLK>,
> + <&gcc GCC_MDSS_ESC1_CLK>;
> + clock-names = "mdp_core",
> + "iface",
> + "bus",
> + "byte",
> + "pixel",
> + "core";
> + assigned-clocks = <&gcc BYTE1_CLK_SRC>,
> + <&gcc PCLK1_CLK_SRC>;
> + assigned-clock-parents = <&dsi_phy1 0>,
> + <&dsi_phy1 1>;
Does this work? Confusingly, BYTE1/PCLK1_CLK_SRC can only have dsi0pll
as parent in gcc-msm8939 and not the dsi1pll. <&dsi_phy1 0/1> is not a
valid parent for those clocks.
Actually I cannot find any mention of mdss_dsi1_pll at all in
downstream. It seems a bit like the PLL functionality in dsi_phy1 is
unused and the PLL in dsi_phy0 is used for both DSI interfaces instead.
No idea why. If this is the case then assigned-clock-parents should
refer to dsi_phy0 here.
> + phys = <&dsi_phy1>;
> + status = "disabled";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> + dsi1_in: endpoint {
> + remote-endpoint = <&mdp5_intf2_out>;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> + dsi1_out: endpoint {
> + };
> + };
> + };
> + };
> +
> + dsi_phy1: phy@1aa0300 {
> + compatible = "qcom,dsi-phy-28nm-lp";
> + reg = <0x01aa0300 0xd4>,
> + <0x01aa0500 0x280>,
> + <0x01aa0780 0x30>;
> + reg-names = "dsi_pll",
> + "dsi_phy",
> + "dsi_phy_regulator";
> +
> + clocks = <&gcc GCC_MDSS_AHB_CLK>,
> + <&rpmcc RPM_SMD_XO_CLK_SRC>;
> + clock-names = "iface", "ref";
> +
> + #clock-cells = <1>;
> + #phy-cells = <0>;
> + status = "disabled";
> + };
> + };
> [...]
> + blsp_dma: dma-controller@7884000 {
> + compatible = "qcom,bam-v1.7.0";
> + reg = <0x07884000 0x23000>;
> + interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&gcc GCC_BLSP1_AHB_CLK>;
> + clock-names = "bam_clk";
> + #dma-cells = <1>;
> + qcom,ee = <0>;
> + status = "disabled";
Please enable this by default, see
https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux.git/commit/?h=for-next&id=0154d3594af3c198532ac7b4ab70f50fb5207a15
> + };
> [...]
> + timer@b020000 {
> + compatible = "arm,armv7-timer-mem";
> + reg = <0x0b020000 0x1000>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> +
> + frame@b021000 {
> + reg = <0x0b021000 0x1000>,
> + <0x0b022000 0x1000>;
> + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
These timer interrupts are still wrong. GIC_SPI 8/7 belong to the timer
frame of the other cluster, 0x0b121000 instead of 0x0b021000.
You need to change the reg addresses like in
https://github.com/msm8916-mainline/linux/commit/0905a152ccb6fe6b94e8c16767993f05c608089c
OR, alternatively: Fix all the interrupt numbers. From the LK source
code we know that this timer frame specifically has GIC_SPI 257 as one
of its interrupts, because LK is making use of it:
https://git.codelinaro.org/clo/la/kernel/lk/-/blob/caf_migration/LA.BR.1.2.9.1_rb1.5/platform/msm8916/include/platform/irqs.h#L47-48
The other timer frames are likely also connected to some other interrupt
number that you might find in documentation or using experiments.
But the easier solution would be keeping the interrupts and just
changing the "reg"s.
> + frame-number = <0>;
> + };
> +
> + frame@b023000 {
> + reg = <0x0b023000 0x1000>;
> + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
> + frame-number = <1>;
> + status = "disabled";
> + };
> +
> + frame@b024000 {
> + reg = <0x0b024000 0x1000>;
> + interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
> + frame-number = <2>;
> + status = "disabled";
> + };
> +
> + frame@b025000 {
> + reg = <0x0b025000 0x1000>;
> + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
> + frame-number = <3>;
> + status = "disabled";
> + };
> +
> + frame@b026000 {
> + reg = <0x0b026000 0x1000>;
> + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
> + frame-number = <4>;
> + status = "disabled";
> + };
> +
> + frame@b027000 {
> + reg = <0x0b027000 0x1000>;
> + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
> + frame-number = <5>;
> + status = "disabled";
> + };
> +
> + frame@b028000 {
> + reg = <0x0b028000 0x1000>;
> + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
> + frame-number = <6>;
> + status = "disabled";
> + };
> + };
> [...]
Thanks!
Stephan
^ permalink raw reply [flat|nested] 32+ messages in thread
* Re: [PATCH v3 5/8] arm64: dts: qcom: Add msm8939 SoC
2023-01-18 9:59 ` Stephan Gerhold
@ 2023-01-18 11:50 ` Bryan O'Donoghue
2023-01-18 12:50 ` Bryan O'Donoghue
2023-01-18 17:33 ` Stephan Gerhold
2023-01-21 22:57 ` Bryan O'Donoghue
1 sibling, 2 replies; 32+ messages in thread
From: Bryan O'Donoghue @ 2023-01-18 11:50 UTC (permalink / raw)
To: Stephan Gerhold
Cc: agross, andersson, konrad.dybcio, djakov, robh+dt,
krzysztof.kozlowski+dt, linux-arm-msm, linux-pm, devicetree,
linux-kernel, benl, shawn.guo, fabien.parent, leo.yan,
dmitry.baryshkov, Jun Nie, James Willcox, Joseph Gates, Max Chen,
Zac Crosby, Vincent Knecht
On 18/01/2023 09:59, Stephan Gerhold wrote:
> On Tue, Jan 17, 2023 at 02:48:43AM +0000, Bryan O'Donoghue wrote:
>> Add msm8939 a derivative SoC of msm8916. This SoC contains a number of key
>> differences to msm8916.
>>
>> - big.LITTLE Octa Core - quad 1.5GHz + quad 1.0GHz
>> - DRAM 1x800 LPDDR3
>> - Camera 4+4 lane CSI
>> - Venus @ 1080p60 HEVC
>> - DSI x 2
>> - Adreno A405
>> - WiFi wcn3660/wcn3680b 802.11ac
>>
>> Co-developed-by: Shawn Guo <shawn.guo@linaro.org>
>> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
>> Co-developed-by: Jun Nie <jun.nie@linaro.org>
>> Signed-off-by: Jun Nie <jun.nie@linaro.org>
>> Co-developed-by: Benjamin Li <benl@squareup.com>
>> Signed-off-by: Benjamin Li <benl@squareup.com>
>> Co-developed-by: James Willcox <jwillcox@squareup.com>
>> Signed-off-by: James Willcox <jwillcox@squareup.com>
>> Co-developed-by: Leo Yan <leo.yan@linaro.org>
>> Signed-off-by: Leo Yan <leo.yan@linaro.org>
>> Co-developed-by: Joseph Gates <jgates@squareup.com>
>> Signed-off-by: Joseph Gates <jgates@squareup.com>
>> Co-developed-by: Max Chen <mchen@squareup.com>
>> Signed-off-by: Max Chen <mchen@squareup.com>
>> Co-developed-by: Zac Crosby <zac@squareup.com>
>> Signed-off-by: Zac Crosby <zac@squareup.com>
>> Co-developed-by: Vincent Knecht <vincent.knecht@mailoo.org>
>> Signed-off-by: Vincent Knecht <vincent.knecht@mailoo.org>
>> Co-developed-by: Stephan Gerhold <stephan@gerhold.net>
>> Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
>> Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
>> ---
>> arch/arm64/boot/dts/qcom/msm8939.dtsi | 2393 +++++++++++++++++++++++++
>> 1 file changed, 2393 insertions(+)
>> create mode 100644 arch/arm64/boot/dts/qcom/msm8939.dtsi
>>
>> diff --git a/arch/arm64/boot/dts/qcom/msm8939.dtsi b/arch/arm64/boot/dts/qcom/msm8939.dtsi
>> new file mode 100644
>> index 0000000000000..8cd358a9fe623
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/qcom/msm8939.dtsi
>> @@ -0,0 +1,2393 @@
>> [...]
>> + cpus {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + cpu0: cpu@100 {
>> + compatible = "arm,cortex-a53";
>> + device_type = "cpu";
>> + enable-method = "spin-table";
>> + reg = <0x100>;
>> + next-level-cache = <&L2_1>;
>> + power-domains = <&vreg_dummy>;
>> + power-domain-names = "cpr";
>
> Why are you adding a dummy power domain here? IMO this would be better
> added together with CPR. Especially because I would expect two power
> domains here later ("mx", "cpr"). For cpufreq you also need to make
> votes for the "MSM8939_VDDMX" power domain.
I'm pretty sure there's binding checks that demand this but, I will
re-verify it.
>
>> + qcom,acc = <&acc0>;
>> + qcom,saw = <&saw0>;
>> + cpu-idle-states = <&CPU_SLEEP_0>;
>> + clocks = <&apcs1_mbox>;
>> + #cooling-cells = <2>;
>> + L2_1: l2-cache {
>> + compatible = "cache";
>> + cache-level = <2>;
>> + };
>> + };
>> [...]
>> + soc: soc@0 {
>> + compatible = "simple-bus";
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + ranges = <0 0 0 0xffffffff>;
>> +
>> + rng@22000 {
>> + compatible = "qcom,prng";
>> + reg = <0x00022000 0x200>;
>> + clocks = <&gcc GCC_PRNG_AHB_CLK>;
>> + clock-names = "core";
>> + };
>> +
>> + qfprom: qfprom@5c000 {
>> + compatible = "qcom,msm8916-qfprom", "qcom,qfprom";
>> + reg = <0x0005c000 0x1000>;
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> +
>> + tsens_caldata: caldata@a0 {
>> + reg = <0xa0 0x5c>;
>> + };
>> + cpr_efuse_init_voltage1: ivoltage1@dc {
>> + reg = <0xdc 0x4>;
>> + bits = <4 6>;
>> + };
>> + cpr_efuse_init_voltage2: ivoltage2@da {
>> + reg = <0xda 0x4>;
>> + bits = <2 6>;
>> + };
>> + cpr_efuse_init_voltage3: ivoltage3@d8 {
>> + reg = <0xd8 0x4>;
>> + bits = <0 6>;
>> + };
>> + cpr_efuse_quot1: quot1@dd {
>> + reg = <0xdd 0x8>;
>> + bits = <2 12>;
>> + };
>> + cpr_efuse_quot2: quot2@db {
>> + reg = <0xdb 0x8>;
>> + bits = <0x0 12>;
>> + };
>> + cpr_efuse_ring1: ring1@de {
>> + reg = <0xde 0x4>;
>> + bits = <6 3>;
>> + };
>> + cpr_efuse_revision: revision@5 {
>> + reg = <0x5 0x1>;
>> + bits = <5 1>;
>> + };
>> + cpr_efuse_revision_high: revision-high@7 {
>> + reg = <0x7 0x1>;
>> + bits = <0 1>;
>> + };
>> + cpr_efuse_pvs_version: pvs@3 {
>> + reg = <0x3 0x1>;
>> + bits = <5 1>;
>> + };
>> + cpr_efuse_pvs_version_high: pvs-high@6 {
>> + reg = <0x6 0x1>;
>> + bits = <2 2>;
>> + };
>> + cpr_efuse_speedbin: speedbin@c {
>> + reg = <0xc 0x1>;
>> + bits = <2 3>;
>> + };
>
> Please add the CPR items later together with CPR. This will make the
> review a bit easier because we don't need to check that these are right
> for the initial submission.
I will excise this if I can, i.e. if the system will still boot once done.
>
>> + };
>> [...]
>> + mdss: display-subsystem@1a00000 {
>> + compatible = "qcom,mdss";
>> + reg = <0x01a00000 0x1000>,
>> + <0x01ac8000 0x3000>;
>> + reg-names = "mdss_phys", "vbif_phys";
>> +
>> + interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
>> + interrupt-controller;
>> +
>> + clocks = <&gcc GCC_MDSS_AHB_CLK>,
>> + <&gcc GCC_MDSS_AXI_CLK>,
>> + <&gcc GCC_MDSS_VSYNC_CLK>;
>> + clock-names = "iface",
>> + "bus",
>> + "vsync";
>> +
>> + power-domains = <&gcc MDSS_GDSC>;
>> +
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + #interrupt-cells = <1>;
>> + ranges;
>> +
>> + mdp: display-controller@1a01000 {
>> + compatible = "qcom,mdp5";
>> + reg = <0x01a01000 0x89000>;
>> + reg-names = "mdp_phys";
>> +
>> + interrupt-parent = <&mdss>;
>> + interrupts = <0>;
>> +
>> + clocks = <&gcc GCC_MDSS_AHB_CLK>,
>> + <&gcc GCC_MDSS_AXI_CLK>,
>> + <&gcc GCC_MDSS_MDP_CLK>,
>> + <&gcc GCC_MDSS_VSYNC_CLK>,
>> + <&gcc GCC_MDP_TBU_CLK>,
>> + <&gcc GCC_MDP_RT_TBU_CLK>;
>> + clock-names = "iface",
>> + "bus",
>> + "core",
>> + "vsync",
>> + "tbu",
>> + "tbu_rt";
>> +
>> + iommus = <&apps_iommu 4>;
>> +
>> + interconnects = <&snoc_mm MASTER_MDP_PORT0 &bimc SLAVE_EBI_CH0>,
>> + <&snoc_mm MASTER_MDP_PORT1 &bimc SLAVE_EBI_CH0>,
>> + <&pcnoc MASTER_SPDM &snoc SLAVE_IMEM>;
>> + interconnect-names = "mdp0-mem", "mdp1-mem", "register-mem";
>
> As I mentioned a already in a direct email at some point, AFAIU adding
> interconnects should be an [almost-] all or nothing step. If you only
> add interconnects for MDP then everything else that needs bandwidth will
> either break or only continue working as a mere side effect of MDP
> voting for permanent high bandwidth.
We did discuss that. You'll also recall we concluded we would have to
revert this patch to make that happen.
commit 76a748e2c1aa976d0c7fef872fa6ff93ce334a8a
Author: Leo Yan <leo.yan@linaro.org>
Date: Sat Apr 16 09:26:34 2022 +0800
interconnect: qcom: msm8939: Use icc_sync_state
but then why not revert for all of these SoCs too ?
drivers/interconnect/qcom/msm8939.c: .sync_state = icc_sync_state,
drivers/interconnect/qcom/msm8974.c: .sync_state = icc_sync_state,
drivers/interconnect/qcom/msm8996.c: .sync_state = icc_sync_state,
drivers/interconnect/qcom/osm-l3.c: .sync_state = icc_sync_state,
drivers/interconnect/qcom/sc7180.c: .sync_state = icc_sync_state,
drivers/interconnect/qcom/sc7280.c: .sync_state = icc_sync_state,
drivers/interconnect/qcom/sc8180x.c: .sync_state = icc_sync_state,
drivers/interconnect/qcom/sc8280xp.c: .sync_state = icc_sync_state,
drivers/interconnect/qcom/sdm845.c: .sync_state = icc_sync_state,
drivers/interconnect/qcom/sdx55.c: .sync_state = icc_sync_state,
drivers/interconnect/qcom/sdx65.c: .sync_state = icc_sync_state,
drivers/interconnect/qcom/sm6350.c: .sync_state = icc_sync_state,
until such time as we have an all or nothing interconnect setup for each
of those SoCs ?
Yes I take your point "some peripherals will appear to work only as a
result of the AHB vote the MDP casts here" but, that is a bug in the
definition of that hypothetical peripheral.
The MDP/display won't run without the interconnect here and the only way
to pull it is to remove sync_state which begs the question why not pull
sync_state for all SoCs without a perfect interconnect description ?
I think that would be a retrograde step.
> (Semi-related side note: "register-mem" is neither documented nor used
> anywhere in the code?)
Oh do you have me there though, this is a holdover from the Android
dtsi. I'll see if it makes a difference dropping this.
>
>> +
>> + ports {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + port@0 {
>> + reg = <0>;
>> + mdp5_intf1_out: endpoint {
>> + remote-endpoint = <&dsi0_in>;
>> + };
>> + };
>> +
>> + port@1 {
>> + reg = <1>;
>> + mdp5_intf2_out: endpoint {
>> + remote-endpoint = <&dsi1_in>;
>> + };
>> + };
>> + };
>> + };
>> +
>> + dsi0: dsi@1a98000 {
>> + compatible = "qcom,msm8916-dsi-ctrl",
>> + "qcom,mdss-dsi-ctrl";
>> + reg = <0x01a98000 0x25c>;
>> + reg-names = "dsi_ctrl";
>> +
>> + interrupt-parent = <&mdss>;
>> + interrupts = <4>;
>> +
>> + power-domains = <&gcc MDSS_GDSC>;
>
> Why is MDSS_GDSC defined again here? The parent-child relationship of
> MDSS->MDP should ensure that the MDSS_GDSC from the parent mdss node
> is on when dsi is.
>
>> +
>> + clocks = <&gcc GCC_MDSS_MDP_CLK>,
>> + <&gcc GCC_MDSS_AHB_CLK>,
>> + <&gcc GCC_MDSS_AXI_CLK>,
>> + <&gcc GCC_MDSS_BYTE0_CLK>,
>> + <&gcc GCC_MDSS_PCLK0_CLK>,
>> + <&gcc GCC_MDSS_ESC0_CLK>;
>> + clock-names = "mdp_core",
>> + "iface",
>> + "bus",
>> + "byte",
>> + "pixel",
>> + "core";
>> + assigned-clocks = <&gcc BYTE0_CLK_SRC>,
>> + <&gcc PCLK0_CLK_SRC>;
>> + assigned-clock-parents = <&dsi_phy0 0>,
>> + <&dsi_phy0 1>;
>> +
>> + phys = <&dsi_phy0>;
>> + status = "disabled";
>> +
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + ports {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + port@0 {
>> + reg = <0>;
>> + dsi0_in: endpoint {
>> + remote-endpoint = <&mdp5_intf1_out>;
>> + };
>> + };
>> +
>> + port@1 {
>> + reg = <1>;
>> + dsi0_out: endpoint {
>> + };
>> + };
>> + };
>> + };
>> +
>> + dsi_phy0: phy@1a98300 {
>> + compatible = "qcom,dsi-phy-28nm-lp";
>> + reg = <0x01a98300 0xd4>,
>> + <0x01a98500 0x280>,
>> + <0x01a98780 0x30>;
>> + reg-names = "dsi_pll",
>> + "dsi_phy",
>> + "dsi_phy_regulator";
>> +
>> + clocks = <&gcc GCC_MDSS_AHB_CLK>,
>> + <&rpmcc RPM_SMD_XO_CLK_SRC>;
>> + clock-names = "iface", "ref";
>> +
>> + #clock-cells = <1>;
>> + #phy-cells = <0>;
>> + status = "disabled";
>> + };
>> +
>> + dsi1: dsi@1aa0000 {
>> + compatible = "qcom,msm8916-dsi-ctrl",
>> + "qcom,mdss-dsi-ctrl";
>> + reg = <0x01aa0000 0x25c>;
>> + reg-names = "dsi_ctrl";
>> +
>> + interrupt-parent = <&mdss>;
>> + interrupts = <5>;
>> +
>> + power-domains = <&gcc MDSS_GDSC>;
>> +
>> + clocks = <&gcc GCC_MDSS_MDP_CLK>,
>> + <&gcc GCC_MDSS_AHB_CLK>,
>> + <&gcc GCC_MDSS_AXI_CLK>,
>> + <&gcc GCC_MDSS_BYTE1_CLK>,
>> + <&gcc GCC_MDSS_PCLK1_CLK>,
>> + <&gcc GCC_MDSS_ESC1_CLK>;
>> + clock-names = "mdp_core",
>> + "iface",
>> + "bus",
>> + "byte",
>> + "pixel",
>> + "core";
>> + assigned-clocks = <&gcc BYTE1_CLK_SRC>,
>> + <&gcc PCLK1_CLK_SRC>;
>> + assigned-clock-parents = <&dsi_phy1 0>,
>> + <&dsi_phy1 1>;
>
> Does this work? Confusingly, BYTE1/PCLK1_CLK_SRC can only have dsi0pll
> as parent in gcc-msm8939 and not the dsi1pll. <&dsi_phy1 0/1> is not a
> valid parent for those clocks.
No you're right, its all wrong. I will correct it
mdss_dsi0: qcom,mdss_dsi@1a98000 {
compatible = "qcom,mdss-dsi-ctrl";
label = "MDSS DSI CTRL->0";
cell-index = <0>;
reg = <0x1a98000 0x25c>,
<0x1a98500 0x2b0>,
<0x193e000 0x30>;
reg-names = "dsi_ctrl", "dsi_phy", "mmss_misc_phys";
qcom,mdss-fb-map = <&mdss_fb0>;
qcom,mdss-mdp = <&mdss_mdp>;
gdsc-supply = <&gdsc_mdss>;
vdda-supply = <&pm8916_l2>;
vdd-supply = <&pm8916_l17>;
vddio-supply = <&pm8916_l6>;
clocks = <&clock_gcc clk_gcc_mdss_mdp_clk>,
<&clock_gcc clk_gcc_mdss_ahb_clk>,
<&clock_gcc clk_gcc_mdss_axi_clk>,
<&clock_gcc_mdss clk_gcc_mdss_byte0_clk>,
<&clock_gcc_mdss clk_gcc_mdss_pclk0_clk>,
<&clock_gcc clk_gcc_mdss_esc0_clk>;
---
bod
^ permalink raw reply [flat|nested] 32+ messages in thread
* Re: [PATCH v3 1/8] dt-bindings: arm: qcom: Document MSM8939 SoC binding
2023-01-18 8:47 ` Stephan Gerhold
@ 2023-01-18 12:05 ` Bryan O'Donoghue
2023-01-18 15:43 ` Stephan Gerhold
2023-01-19 0:32 ` Bryan O'Donoghue
1 sibling, 1 reply; 32+ messages in thread
From: Bryan O'Donoghue @ 2023-01-18 12:05 UTC (permalink / raw)
To: Stephan Gerhold
Cc: agross, andersson, konrad.dybcio, djakov, robh+dt,
krzysztof.kozlowski+dt, linux-arm-msm, linux-pm, devicetree,
linux-kernel, benl, shawn.guo, fabien.parent, leo.yan,
dmitry.baryshkov, Krzysztof Kozlowski
On 18/01/2023 08:47, Stephan Gerhold wrote:
> On Tue, Jan 17, 2023 at 02:48:39AM +0000, Bryan O'Donoghue wrote:
>> Document the MSM8939 and supported boards in upstream Sony "Tulip" M4 Aqua
>> and Square APQ8039 T2.
>>
>> MSM8939 is one of the older SoCs so we need to expand the list of
>> qcom,board-ids to allow for the bootloader DTS board-id matching
>> dependency.
>>
>
> The original LK bootloaders cannot boot your msm8939.dtsi correctly,
> because a spin-table implementation is required to get the other CPU
> cores up. This means that a modified bootloader is always needed from
> the upstream point of view, since I doubt anyone wants to use these
> devices with a single core only. lk2nd (as the primary spin-table
> implementation right now) has never required qcom,board-ids and any
> custom LK would be easy to patch to ignore these.
The system boots just fine with the shipped LK. We get display, USB, SD,
WiFi.
We just don't support booting the second cluster via any other means
than lk2nd right now.
You could also not use lk2nd, stick with your default LK and import LPM
patches.
Default LK:
root@linaro-alip:~# cat /proc/cpuinfo
processor : 0
BogoMIPS : 38.40
Features : fp asimd evtstrm aes pmull sha1 sha2 crc32 cpuid
CPU implementer : 0x41
CPU architecture: 8
CPU variant : 0x0
CPU part : 0xd03
CPU revision : 4
root@linaro-alip:~# iw wlan0 info
Interface wlan0
ifindex 6
wdev 0x1
addr e2:b9:a0:ef:3a:ba
type managed
wiphy 0
channel 52 (5260 MHz), width: 80 MHz, center1: 5290 MHz
txpower 20.00 dBm
multicast TXQ:
qsz-byt qsz-pkt flows drops marks overlmt hashcol
tx-bytes tx-packets
0 0 0 0 0 0 0
0 0
root@linaro-alip:~# uname -a
Linux linaro-alip 6.2.0-rc4-next-20230116-00029-gf1a46ff9e812-dirty #392
SMP PREEMPT Tue Jan 17 23:46:42 GMT 2023 aarch64 GNU/Linux
LK2ND:
root@linaro-alip:~# cat /proc/cpuinfo
processor : 0
BogoMIPS : 38.40
Features : fp asimd evtstrm aes pmull sha1 sha2 crc32 cpuid
CPU implementer : 0x41
CPU architecture: 8
CPU variant : 0x0
CPU part : 0xd03
CPU revision : 4
processor : 1
BogoMIPS : 38.40
Features : fp asimd evtstrm aes pmull sha1 sha2 crc32 cpuid
CPU implementer : 0x41
CPU architecture: 8
CPU variant : 0x0
CPU part : 0xd03
CPU revision : 4
processor : 2
BogoMIPS : 38.40
Features : fp asimd evtstrm aes pmull sha1 sha2 crc32 cpuid
CPU implementer : 0x41
CPU architecture: 8
CPU variant : 0x0
CPU part : 0xd03
CPU revision : 4
processor : 3
BogoMIPS : 38.40
Features : fp asimd evtstrm aes pmull sha1 sha2 crc32 cpuid
CPU implementer : 0x41
CPU architecture: 8
CPU variant : 0x0
CPU part : 0xd03
CPU revision : 4
processor : 4
BogoMIPS : 38.40
Features : fp asimd evtstrm aes pmull sha1 sha2 crc32 cpuid
CPU implementer : 0x41
CPU architecture: 8
CPU variant : 0x0
CPU part : 0xd03
CPU revision : 4
processor : 5
BogoMIPS : 38.40
Features : fp asimd evtstrm aes pmull sha1 sha2 crc32 cpuid
CPU implementer : 0x41
CPU architecture: 8
CPU variant : 0x0
CPU part : 0xd03
CPU revision : 4
processor : 6
BogoMIPS : 38.40
Features : fp asimd evtstrm aes pmull sha1 sha2 crc32 cpuid
CPU implementer : 0x41
CPU architecture: 8
CPU variant : 0x0
CPU part : 0xd03
CPU revision : 4
processor : 7
BogoMIPS : 38.40
Features : fp asimd evtstrm aes pmull sha1 sha2 crc32 cpuid
CPU implementer : 0x41
CPU architecture: 8
CPU variant : 0x0
CPU part : 0xd03
CPU revision : 4
root@linaro-alip:~# iw wlan0 info
Interface wlan0
ifindex 6
wdev 0x1
addr 02:00:0e:66:5c:21
type managed
wiphy 0
channel 64 (5320 MHz), width: 80 MHz, center1: 5290 MHz
txpower 20.00 dBm
multicast TXQ:
qsz-byt qsz-pkt flows drops marks overlmt hashcol
tx-bytes tx-packets
0 0 0 0 0 0 0
0 0
root@linaro-alip:~# uname -a
Linux linaro-alip 6.2.0-rc4-next-20230116-00029-gf1a46ff9e812-dirty #392
SMP PREEMPT Tue Jan 17 23:46:42 GMT 2023 aarch64 GNU/Linux
---
bod
^ permalink raw reply [flat|nested] 32+ messages in thread
* Re: [PATCH v3 5/8] arm64: dts: qcom: Add msm8939 SoC
2023-01-18 11:50 ` Bryan O'Donoghue
@ 2023-01-18 12:50 ` Bryan O'Donoghue
2023-01-18 17:33 ` Stephan Gerhold
1 sibling, 0 replies; 32+ messages in thread
From: Bryan O'Donoghue @ 2023-01-18 12:50 UTC (permalink / raw)
To: Stephan Gerhold
Cc: agross, andersson, konrad.dybcio, djakov, robh+dt,
krzysztof.kozlowski+dt, linux-arm-msm, linux-pm, devicetree,
linux-kernel, benl, shawn.guo, fabien.parent, leo.yan,
dmitry.baryshkov, Jun Nie, James Willcox, Joseph Gates, Max Chen,
Zac Crosby, Vincent Knecht
On 18/01/2023 11:50, Bryan O'Donoghue wrote:
>>> + clocks = <&gcc GCC_MDSS_MDP_CLK>,
>>> + <&gcc GCC_MDSS_AHB_CLK>,
>>> + <&gcc GCC_MDSS_AXI_CLK>,
>>> + <&gcc GCC_MDSS_BYTE1_CLK>,
>>> + <&gcc GCC_MDSS_PCLK1_CLK>,
>>> + <&gcc GCC_MDSS_ESC1_CLK>;
>>> + clock-names = "mdp_core",
>>> + "iface",
>>> + "bus",
>>> + "byte",
>>> + "pixel",
>>> + "core";
>>> + assigned-clocks = <&gcc BYTE1_CLK_SRC>,
>>> + <&gcc PCLK1_CLK_SRC>;
>>> + assigned-clock-parents = <&dsi_phy1 0>,
>>> + <&dsi_phy1 1>;
>>
>> Does this work? Confusingly, BYTE1/PCLK1_CLK_SRC can only have dsi0pll
>> as parent in gcc-msm8939 and not the dsi1pll. <&dsi_phy1 0/1> is not a
>> valid parent for those clocks.
>
> No you're right, its all wrong. I will correct it
>
> mdss_dsi0: qcom,mdss_dsi@1a98000 {
> compatible = "qcom,mdss-dsi-ctrl";
> label = "MDSS DSI CTRL->0";
> cell-index = <0>;
> reg = <0x1a98000 0x25c>,
> <0x1a98500 0x2b0>,
> <0x193e000 0x30>;
> reg-names = "dsi_ctrl", "dsi_phy", "mmss_misc_phys";
> qcom,mdss-fb-map = <&mdss_fb0>;
> qcom,mdss-mdp = <&mdss_mdp>;
> gdsc-supply = <&gdsc_mdss>;
> vdda-supply = <&pm8916_l2>;
> vdd-supply = <&pm8916_l17>;
> vddio-supply = <&pm8916_l6>;
> clocks = <&clock_gcc clk_gcc_mdss_mdp_clk>,
> <&clock_gcc clk_gcc_mdss_ahb_clk>,
> <&clock_gcc clk_gcc_mdss_axi_clk>,
> <&clock_gcc_mdss clk_gcc_mdss_byte0_clk>,
> <&clock_gcc_mdss clk_gcc_mdss_pclk0_clk>,
> <&clock_gcc clk_gcc_mdss_esc0_clk>;
Sorry what am I saying that's the wrong dsiX
Here's downstream - byte1, plck1, esc1 exist
mdss_dsi1: qcom,mdss_dsi@1aa0000 {
compatible = "qcom,mdss-dsi-ctrl";
label = "MDSS DSI CTRL->1";
cell-index = <1>;
reg = <0x1aa0000 0x25c>,
<0x1aa0500 0x2b0>,
<0x193e000 0x30>;
reg-names = "dsi_ctrl", "dsi_phy", "mmss_misc_phys";
qcom,mdss-fb-map = <&mdss_fb0>;
qcom,mdss-mdp = <&mdss_mdp>;
gdsc-supply = <&gdsc_mdss>;
vdda-supply = <&pm8916_l2>;
vdd-supply = <&pm8916_l17>;
vddio-supply = <&pm8916_l6>;
clocks = <&clock_gcc clk_gcc_mdss_mdp_clk>,
<&clock_gcc clk_gcc_mdss_ahb_clk>,
<&clock_gcc clk_gcc_mdss_axi_clk>,
<&clock_gcc_mdss clk_gcc_mdss_byte1_clk>,
<&clock_gcc_mdss clk_gcc_mdss_pclk1_clk>,
<&clock_gcc clk_gcc_mdss_esc1_clk>;
clock-names = "mdp_core_clk", "iface_clk", "bus_clk",
"byte_clk", "pixel_clk", "core_clk";
Parent clock is gpll0a but they waggle different rcgr addresses
static struct clk_rcg2 byte0_clk_src = {
.cmd_rcgr = 0x4d044, <- here
.hid_width = 5,
.parent_map = gcc_xo_gpll0a_dsibyte_map,
.clkr.hw.init = &(struct clk_init_data){
.name = "byte0_clk_src",
static struct clk_rcg2 byte1_clk_src = {
.cmd_rcgr = 0x4d0b0, <- and here
.hid_width = 5,
.parent_map = gcc_xo_gpll0a_dsibyte_map,
.clkr.hw.init = &(struct clk_init_data){
.name = "byte1_clk_src",
It *should* work even with the wrong name but, I will send a GCC update
to address the naming, which looks wrong.
---
bod
^ permalink raw reply [flat|nested] 32+ messages in thread
* Re: [PATCH v3 4/8] clk: qcom: smd-rpm: msm8936: Add PMIC gated RPM_SMD_XO_*
2023-01-17 2:48 ` [PATCH v3 4/8] clk: qcom: smd-rpm: msm8936: Add PMIC gated RPM_SMD_XO_* Bryan O'Donoghue
@ 2023-01-18 13:49 ` Konrad Dybcio
0 siblings, 0 replies; 32+ messages in thread
From: Konrad Dybcio @ 2023-01-18 13:49 UTC (permalink / raw)
To: Bryan O'Donoghue, agross, andersson, djakov, robh+dt,
krzysztof.kozlowski+dt
Cc: linux-arm-msm, linux-pm, devicetree, linux-kernel, benl,
shawn.guo, fabien.parent, leo.yan, dmitry.baryshkov
On 17.01.2023 03:48, Bryan O'Donoghue wrote:
> The XO crystal input is buffered through the PMIC and controlled by RPM.
> Create the relevant clock gate representation in the RPM clock definitions.
>
> Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
> ---
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Konrad
> drivers/clk/qcom/clk-smd-rpm.c | 2 ++
> 1 file changed, 2 insertions(+)
>
> diff --git a/drivers/clk/qcom/clk-smd-rpm.c b/drivers/clk/qcom/clk-smd-rpm.c
> index 8f6e274c60301..6f23ca4828f44 100644
> --- a/drivers/clk/qcom/clk-smd-rpm.c
> +++ b/drivers/clk/qcom/clk-smd-rpm.c
> @@ -574,6 +574,8 @@ static const struct rpm_smd_clk_desc rpm_clk_msm8916 = {
> };
>
> static struct clk_smd_rpm *msm8936_clks[] = {
> + [RPM_SMD_XO_CLK_SRC] = &clk_smd_rpm_branch_bi_tcxo,
> + [RPM_SMD_XO_A_CLK_SRC] = &clk_smd_rpm_branch_bi_tcxo_a,
> [RPM_SMD_PCNOC_CLK] = &clk_smd_rpm_bus_0_pcnoc_clk,
> [RPM_SMD_PCNOC_A_CLK] = &clk_smd_rpm_bus_0_pcnoc_a_clk,
> [RPM_SMD_SNOC_CLK] = &clk_smd_rpm_bus_1_snoc_clk,
^ permalink raw reply [flat|nested] 32+ messages in thread
* Re: [PATCH v3 6/8] arm64: dts: qcom: Add msm8939-pm8916.dtsi include
2023-01-17 2:48 ` [PATCH v3 6/8] arm64: dts: qcom: Add msm8939-pm8916.dtsi include Bryan O'Donoghue
@ 2023-01-18 13:49 ` Konrad Dybcio
0 siblings, 0 replies; 32+ messages in thread
From: Konrad Dybcio @ 2023-01-18 13:49 UTC (permalink / raw)
To: Bryan O'Donoghue, agross, andersson, djakov, robh+dt,
krzysztof.kozlowski+dt
Cc: linux-arm-msm, linux-pm, devicetree, linux-kernel, benl,
shawn.guo, fabien.parent, leo.yan, dmitry.baryshkov,
Stephan Gerhold
On 17.01.2023 03:48, Bryan O'Donoghue wrote:
> From: Stephan Gerhold <stephan@gerhold.net>
>
> The msm8939-pm8916.dtsi include configures the regulator supplies of
> MSM8939 used together with PM8916, as recommended by Qualcomm. In rare
> cases where boards deviate from the recommended design they can just
> avoid using this include.
>
> Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
> Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
> ---
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Konrad
> arch/arm64/boot/dts/qcom/msm8939-pm8916.dtsi | 82 ++++++++++++++++++++
> 1 file changed, 82 insertions(+)
> create mode 100644 arch/arm64/boot/dts/qcom/msm8939-pm8916.dtsi
>
> diff --git a/arch/arm64/boot/dts/qcom/msm8939-pm8916.dtsi b/arch/arm64/boot/dts/qcom/msm8939-pm8916.dtsi
> new file mode 100644
> index 0000000000000..18a1b3cca01d6
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/msm8939-pm8916.dtsi
> @@ -0,0 +1,82 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +
> +#include "msm8939.dtsi"
> +#include "pm8916.dtsi"
> +
> +&dsi0 {
> + vdda-supply = <&pm8916_l2>;
> + vddio-supply = <&pm8916_l6>;
> +};
> +
> +&dsi1 {
> + vdda-supply = <&pm8916_l2>;
> + vddio-supply = <&pm8916_l6>;
> +};
> +
> +&dsi_phy0 {
> + vddio-supply = <&pm8916_l6>;
> +};
> +
> +&dsi_phy1 {
> + vddio-supply = <&pm8916_l6>;
> +};
> +
> +&mpss {
> + pll-supply = <&pm8916_l7>;
> +};
> +
> +&pronto {
> + vddpx-supply = <&pm8916_l7>;
> +
> + iris {
> + vddxo-supply = <&pm8916_l7>;
> + vddrfa-supply = <&pm8916_s3>;
> + vddpa-supply = <&pm8916_l9>;
> + vdddig-supply = <&pm8916_l5>;
> + };
> +};
> +
> +&sdhc_1 {
> + vmmc-supply = <&pm8916_l8>;
> + vqmmc-supply = <&pm8916_l5>;
> +};
> +
> +&sdhc_2 {
> + vmmc-supply = <&pm8916_l11>;
> + vqmmc-supply = <&pm8916_l12>;
> +};
> +
> +&usb_hs_phy {
> + v1p8-supply = <&pm8916_l7>;
> + v3p3-supply = <&pm8916_l13>;
> +};
> +
> +&rpm_requests {
> + smd_rpm_regulators: regulators {
> + compatible = "qcom,rpm-pm8916-regulators";
> +
> + /* pm8916_s1 is managed by rpmpd (MSM8939_VDDMDCX) */
> + /* pm8916_s2 is managed by rpmpd (MSM8939_VDDCX) */
> + pm8916_s3: s3 {};
> + pm8916_s4: s4 {};
> +
> + pm8916_l1: l1 {};
> + pm8916_l2: l2 {};
> + /* pm8916_l3 is managed by rpmpd (MSM8939_VDDMX) */
> + pm8916_l4: l4 {};
> + pm8916_l5: l5 {};
> + pm8916_l6: l6 {};
> + pm8916_l7: l7 {};
> + pm8916_l8: l8 {};
> + pm8916_l9: l9 {};
> + pm8916_l10: l10 {};
> + pm8916_l11: l11 {};
> + pm8916_l12: l12 {};
> + pm8916_l13: l13 {};
> + pm8916_l14: l14 {};
> + pm8916_l15: l15 {};
> + pm8916_l16: l16 {};
> + pm8916_l17: l17 {};
> + pm8916_l18: l18 {};
> + };
> +};
^ permalink raw reply [flat|nested] 32+ messages in thread
* Re: [PATCH v3 8/8] arm64: dts: qcom: Add msm8939 Sony Xperia M4 Aqua
2023-01-17 2:48 ` [PATCH v3 8/8] arm64: dts: qcom: Add msm8939 Sony Xperia M4 Aqua Bryan O'Donoghue
@ 2023-01-18 14:42 ` Konrad Dybcio
2023-01-18 15:11 ` Bryan O'Donoghue
0 siblings, 1 reply; 32+ messages in thread
From: Konrad Dybcio @ 2023-01-18 14:42 UTC (permalink / raw)
To: Bryan O'Donoghue, agross, andersson, djakov, robh+dt,
krzysztof.kozlowski+dt
Cc: linux-arm-msm, linux-pm, devicetree, linux-kernel, benl,
shawn.guo, fabien.parent, leo.yan, dmitry.baryshkov
On 17.01.2023 03:48, Bryan O'Donoghue wrote:
> Add a basic booting DTS for the Sony Xperia M4 Aqua aka "tulip".
>
> Tulip is paired with:
>
> - wcn3660
> - smb1360 battery charger
> - 720p Truly NT35521 Panel
>
> Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
> ---
> arch/arm64/boot/dts/qcom/Makefile | 1 +
> arch/arm64/boot/dts/qcom/apq8039-t2.dts | 2 -
> .../qcom/msm8939-sony-xperia-kanuti-tulip.dts | 466 ++++++++++++++++++
> 3 files changed, 467 insertions(+), 2 deletions(-)
> create mode 100644 arch/arm64/boot/dts/qcom/msm8939-sony-xperia-kanuti-tulip.dts
>
> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
> index 5c47d1fb50b01..8b9fa1deadbe0 100644
> --- a/arch/arm64/boot/dts/qcom/Makefile
> +++ b/arch/arm64/boot/dts/qcom/Makefile
> @@ -24,6 +24,7 @@ dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-grandmax.dtb
> dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-j5.dtb
> dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-serranove.dtb
> dtb-$(CONFIG_ARCH_QCOM) += msm8916-wingtech-wt88047.dtb
> +dtb-$(CONFIG_ARCH_QCOM) += msm8939-sony-xperia-kanuti-tulip.dtb
> dtb-$(CONFIG_ARCH_QCOM) += msm8953-motorola-potter.dtb
> dtb-$(CONFIG_ARCH_QCOM) += msm8953-xiaomi-daisy.dtb
> dtb-$(CONFIG_ARCH_QCOM) += msm8953-xiaomi-mido.dtb
> diff --git a/arch/arm64/boot/dts/qcom/apq8039-t2.dts b/arch/arm64/boot/dts/qcom/apq8039-t2.dts
> index 21f5a21f76135..ee04cf294179f 100644
> --- a/arch/arm64/boot/dts/qcom/apq8039-t2.dts
> +++ b/arch/arm64/boot/dts/qcom/apq8039-t2.dts
> @@ -491,8 +491,6 @@ pm8916_l18: l18 {
> };
>
> &sdhc_1 {
> - vmmc-supply = <&pm8916_l8>;
> - vqmmc-supply = <&pm8916_l5>;
> pinctrl-names = "default", "sleep";
> pinctrl-0 = <&sdc1_default_state>;
> pinctrl-1 = <&sdc1_sleep_state>;
This hunk doesn't belong in this patch..
> diff --git a/arch/arm64/boot/dts/qcom/msm8939-sony-xperia-kanuti-tulip.dts b/arch/arm64/boot/dts/qcom/msm8939-sony-xperia-kanuti-tulip.dts
> new file mode 100644
> index 0000000000000..ffe3ea17dcae2
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/msm8939-sony-xperia-kanuti-tulip.dts
> @@ -0,0 +1,466 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (c) 2015, The Linux Foundation. All rights reserved.
> + * Copyright (c) 2022-2023, Bryan O'Donoghue.
> + *
> + */
> +
> +/dts-v1/;
> +
> +#include "msm8939.dtsi"
> +#include "msm8939-pm8916.dtsi"
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
> +
> +/ {
> + model = "Sony Xperia M4 Aqua";
> + compatible = "sony,kanuti-tulip", "qcom,msm8939";
> +
> + qcom,board-id = <8 0>;
> + qcom,msm-id = <239 0>, <239 0x30000>, <241 0x30000>, <263 0x30000>;
> +
> + aliases {
> + mmc0 = &sdhc_1; /* SDC1 eMMC slot */
> + mmc1 = &sdhc_2; /* SDC2 SD card slot */
> + serial0 = &blsp1_uart2;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + negative5_reg: negative5-regulator {
> + compatible = "regulator-fixed";
> + pinctrl-names = "default";
> + pinctrl-0 = <&negative5_reg_default>;
> + regulator-name = "negative5_reg";
> + gpio = <&tlmm 17 GPIO_ACTIVE_LOW>;
> + startup-delay-us = <0>;
> + };
> +
> + positive5_reg: positive5-regulator {
> + compatible = "regulator-fixed";
> + pinctrl-names = "default";
> + pinctrl-0 = <&positive5_reg_default>;
> + regulator-name = "positive5_reg";
> + gpio = <&tlmm 114 GPIO_ACTIVE_LOW>;
> + startup-delay-us = <0>;
> + };
> +
> + usb_id: usb-id {
> + compatible = "linux,extcon-usb-gpio";
> + id-gpio = <&tlmm 110 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&usb_id_default>;
> + };
> +};
> +
> +&blsp_dma {
> + status = "okay";
> +};
> +
> +&dsi0 {
> + vdda-supply = <&pm8916_l2>;
> + vddio-supply = <&pm8916_l16>;
#include "msm8939-pm8916.dtsi"
> + status = "okay";
> +
> + panel@0 {
> + compatible = "sony,tulip-truly-nt35521";
> + reg = <0>;
> + positive5-supply = <&positive5_reg>;
> + negative5-supply = <&negative5_reg>;
> + reset-gpios = <&tlmm 25 GPIO_ACTIVE_LOW>;
> + enable-gpios = <&tlmm 10 GPIO_ACTIVE_LOW>;
> +
> + ports {
> + port {
> + panel_in: endpoint {
> + remote-endpoint = <&dsi0_out>;
> + };
> + };
> + };
> +
> + };
> +};
> +
> +&dsi0_out {
> + remote-endpoint = <&panel_in>;
> + data-lanes = <0 1 2 3>;
> +};
> +
> +&dsi_phy0 {
> + vddio-supply = <&pm8916_l16>;
That sounds strange.. you sure it's this one?
> + qcom,dsi-phy-regulator-ldo-mode;
> + status = "okay";
> +};
> +
> +&tlmm {
> + ak8963_default: ak8963-default-state {
> + pins = "gpio69";
> + function = "gpio";
> + drive-strength = <6>;
> + bias-pull-up;
> + };
> +
> + ak8963_sleep: ak8963-sleep-state {
> + pins = "gpio69";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-pull-down;
> + };
> +
> + /* Ambient light and proximity sensor apds9930 and apds9900 */
> + apds99xx_default: apds99xx-default-state {
> + pins = "gpio113";
> + function = "gpio";
> + drive-strength = <6>;
> + bias-pull-up;
> + };
> +
> + apds99xx_sleep: apds99xx-sleep-state {
> + pins = "gpio113";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-pull-down;
> + };
> +
> + cam_sensor_flash_default: cam-sensor-flash-default-state {
> + pins = "gpio98", "gpio97";
> + function = "gpio";
> + bias-disable;
> + drive-strength = <2>;
> + };
> +
> + cci1_default: cci1-default-state {
> + pins = "gpio31", "gpio32";
> + function = "cci_i2c";
> + drive-strength = <2>;
> + bias-disable;
> + };
> +
> + cdc_ext_spk_pa_active: cdc-ext-spk-pa-on-state {
> + pins = "gpio0";
> + function = "gpio";
> + drive-strength = <8>;
> + output-low;
> + };
> +
> + cdc_ext_spk_pa_sus: cdc-ext-spk-pa-off-state {
> + pins = "gpio0";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-disable;
> + };
> +
> + cdc_slim_lines_act: lines-on-state {
> + pins = "gpio63";
> + function = "cdc_pdm0";
> + drive-strength = <8>;
> + output-high;
> + };
> +
> + cdc_slim_lines_sus: lines-off-state {
> + pins = "gpio63";
> + function = "cdc_pdm0";
> + drive-strength = <2>;
> + bias-disable;
> + };
> +
> + cross_conn_det_act: lines-on-state {
> + pins = "gpio120";
> + function = "gpio";
> + drive-strength = <8>;
> + bias-pull-down;
> + output-low;
> + };
> +
> + cross_conn_det_sus: lines-off-state {
> + pins = "gpio120";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-pull-down;
> + };
> +
> + ext_buck_vsel: vsel0-state {
> + pins = "gpio111";
> + function = "gpio";
> + drive-strength = <2>;
> + };
> +
> + ext_cdc_tlmm_lines_act: tlmm-lines-on-state {
> + pins = "gpio116", "gpio112", "gpio117", "gpio118", "gpio119";
> + function = "gpio";
> + drive-strength = <8>;
> + bias-disable;
> + };
> +
> + ext_cdc_tlmm_lines_sus: tlmm-lines-off-state {
> + pins = "gpio116", "gpio112", "gpio117", "gpio118", "gpio119";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-disable;
> + };
> +
> + gpio_key_suspend: gpio-key-suspend-state {
> + pins = "gpio107", "gpio108", "gpio109";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
> +
> + negative5_reg_default: negative5-reg-default-state {
> + pins = "gpio17";
> + function = "gpio";
> + output-low;
> + };
> +
> + positive5_reg_default: positive5-reg-default-state {
> + pins = "gpio114";
> + function = "gpio";
> + output-low;
> + };
> +
> + /* Gyroscope and accelerometer sensor combo */
> + mpu6050_default: mpu6050-default-state {
> + pins = "gpio115";
> + function = "gpio";
> + drive-strength = <6>;
> + bias-pull-up;
> + };
> +
> + mpu6050_sleep: mpu6050-sleep-state {
> + pins = "gpio115";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-pull-down;
> + };
> +
> + nfc_disable_active: nfc-disable-active-state {
> + pins = "gpio20";
> + function = "gpio";
> + drive-strength = <6>;
> + bias-pull-up;
> + };
> +
> + nfc_disable_suspend: nfc-disable-suspend-state {
> + pins = "gpio20";
> + function = "gpio";
> + drive-strength = <6>;
> + bias-disable;
> + };
> +
> + nfc_int_active: nfc-int-active-state {
> + pins = "gpio21";
> + function = "gpio";
> + drive-strength = <6>;
> + bias-pull-up;
> + };
> +
> + nfc_int_suspend: nfc-int-suspend-state {
> + pins = "gpio21";
> + function = "gpio";
> + drive-strength = <6>;
> + bias-pull-up;
> + };
> +
> + nt35521_te_default: nt35521-te-default-state {
> + pins = "gpio24";
> + function = "gpio";
> + drive-strength = <6>;
> + bias-pull-down;
> + };
> +
> + nt35521_backlight: nt35521-backlight-default-state {
> + pins = "gpio10";
> + function = "gpio";
> + drive-strength = <6>;
> + bias-pull-down;
> + };
> +
> + smb_int: smb-int-default-state {
> + pins = "gpio62";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
> +
> + ts_int_active: ts-int-active-state {
> + pins = "gpio13";
> + function = "gpio";
> + drive-strength = <16>;
> + bias-pull-up;
> + };
> +
> + ts_int_suspend: ts-int-suspend-state {
> + pins = "gpio13";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-pull-down;
> + };
> +
> + ts_reset_active: ts-reset-active-state {
> + pins = "gpio12";
> + function = "gpio";
> + drive-strength = <16>;
> + bias-pull-up;
> + };
> +
> + ts_reset_suspend: ts-reset-suspend-state {
> + pins = "gpio12";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-pull-down;
> + };
> +
> + ts_release: ts-release-default-state {
> + pins = "gpio13", "gpio12";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-pull-down;
> + };
> +
> + usb_id_default: usb-id-default-state {
> + pins = "gpio110";
> + function = "gpio";
> + drive-strength = <8>;
> + bias-pull-up;
> + };
> +};
> +
> +&pronto {
> + status = "okay";
> +
> + iris {
> + compatible = "qcom,wcn3660";
> + };
> +};
> +
> +&smd_rpm_regulators {
> + vdd_l1_l2_l3-supply = <&pm8916_s3>;
> + vdd_l4_l5_l6-supply = <&pm8916_s4>;
> + vdd_l7-supply = <&pm8916_s4>;
> +
> + pm8916_s3: s3 {
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1300000>;
> + };
> +
> + pm8916_s4: s4 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <2100000>;
> + };
> +
> + pm8916_l2: l2 {
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + };
> +
> + pm8916_l4: l4 {
> + regulator-min-microvolt = <2050000>;
> + regulator-max-microvolt = <2050000>;
> + };
> +
> + pm8916_l5: l5 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + };
> +
> + pm8916_l6: l6 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + };
> +
> + pm8916_l7: l7 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + };
> +
> + pm8916_l8: l8 {
> + regulator-min-microvolt = <2850000>;
> + regulator-max-microvolt = <2900000>;
> + };
> +
> + pm8916_l9: l9 {
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + pm8916_l10: l10 {
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + pm8916_l11: l11 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-allow-set-load;
Please put this below regulator-system-load for consistency with
other DTs.
> + regulator-system-load = <200000>;
> + };
> +
> + pm8916_l12: l12 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + pm8916_l13: l13 {
> + regulator-min-microvolt = <3075000>;
> + regulator-max-microvolt = <3075000>;
> + };
> +
> + pm8916_l14: l14 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + pm8916_l15: l15 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + pm8916_l16: l16 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + pm8916_l17: l17 {
> + regulator-min-microvolt = <2850000>;
> + regulator-max-microvolt = <2850000>;
> + };
> +
> + pm8916_l18: l18 {
> + regulator-min-microvolt = <2700000>;
> + regulator-max-microvolt = <2700000>;
> + };
> +};
> +
> +&sdhc_1 {
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&sdc1_default_state>;
> + pinctrl-1 = <&sdc1_sleep_state>;
> + status = "okay";
> +};
> +
> +&sdhc_2 {
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&sdc2_default_state>;
> + pinctrl-1 = <&sdc2_sleep_state>;
> + cd-gpios = <&tlmm 38 GPIO_ACTIVE_HIGH>;
> + status = "okay";
> +};
> +
> +&usb {
> + extcon = <&usb_id>, <&usb_id>;
> + status = "okay";
> +
> + ulpi {
> + usb_hs_phy: phy {
> + v1p8-supply = <&pm8916_l7>;
> + v3p3-supply = <&pm8916_l13>;
#include "msm8939-pm8916.dtsi"
Konrad
> + };
> + };
> +};
> +
> +&usb_hs_phy {
> + extcon = <&usb_id>;
> +};
^ permalink raw reply [flat|nested] 32+ messages in thread
* Re: [PATCH v3 8/8] arm64: dts: qcom: Add msm8939 Sony Xperia M4 Aqua
2023-01-18 14:42 ` Konrad Dybcio
@ 2023-01-18 15:11 ` Bryan O'Donoghue
0 siblings, 0 replies; 32+ messages in thread
From: Bryan O'Donoghue @ 2023-01-18 15:11 UTC (permalink / raw)
To: Konrad Dybcio, agross, andersson, djakov, robh+dt,
krzysztof.kozlowski+dt
Cc: linux-arm-msm, linux-pm, devicetree, linux-kernel, benl,
shawn.guo, fabien.parent, leo.yan, dmitry.baryshkov
On 18/01/2023 14:42, Konrad Dybcio wrote:
>> &sdhc_1 {
>> - vmmc-supply = <&pm8916_l8>;
>> - vqmmc-supply = <&pm8916_l5>;
>> pinctrl-names = "default", "sleep";
>> pinctrl-0 = <&sdc1_default_state>;
>> pinctrl-1 = <&sdc1_sleep_state>;
> This hunk doesn't belong in this patch..
>
>
bah.
squashing
^ permalink raw reply [flat|nested] 32+ messages in thread
* Re: [PATCH v3 1/8] dt-bindings: arm: qcom: Document MSM8939 SoC binding
2023-01-18 12:05 ` Bryan O'Donoghue
@ 2023-01-18 15:43 ` Stephan Gerhold
0 siblings, 0 replies; 32+ messages in thread
From: Stephan Gerhold @ 2023-01-18 15:43 UTC (permalink / raw)
To: Bryan O'Donoghue
Cc: agross, andersson, konrad.dybcio, djakov, robh+dt,
krzysztof.kozlowski+dt, linux-arm-msm, linux-pm, devicetree,
linux-kernel, benl, shawn.guo, fabien.parent, leo.yan,
dmitry.baryshkov, Krzysztof Kozlowski
On Wed, Jan 18, 2023 at 12:05:50PM +0000, Bryan O'Donoghue wrote:
> On 18/01/2023 08:47, Stephan Gerhold wrote:
> > On Tue, Jan 17, 2023 at 02:48:39AM +0000, Bryan O'Donoghue wrote:
> > > Document the MSM8939 and supported boards in upstream Sony "Tulip" M4 Aqua
> > > and Square APQ8039 T2.
> > >
> > > MSM8939 is one of the older SoCs so we need to expand the list of
> > > qcom,board-ids to allow for the bootloader DTS board-id matching
> > > dependency.
> > >
> >
> > The original LK bootloaders cannot boot your msm8939.dtsi correctly,
> > because a spin-table implementation is required to get the other CPU
> > cores up. This means that a modified bootloader is always needed from
> > the upstream point of view, since I doubt anyone wants to use these
> > devices with a single core only. lk2nd (as the primary spin-table
> > implementation right now) has never required qcom,board-ids and any
> > custom LK would be easy to patch to ignore these.
>
> The system boots just fine with the shipped LK. We get display, USB, SD,
> WiFi.
>
> We just don't support booting the second cluster via any other means than
> lk2nd right now.
>
> You could also not use lk2nd, stick with your default LK and import LPM
> patches.
>
My point is: If you import out of tree LPM patches you can also just
import an extra patch that adds the qcom,board-id property where needed.
The qcom,board-id is only needed/used in configurations where you need
to add those extra LPM patches on top anyway. Those configurations are
(sadly) not supported from the upstream point of view, since only PSCI
or spin-table are supposed to be used for CPU bring-up/idle.
Anyway, for me personally there is no difference if the funky
qcom,board-id properties are there or not, so I'll leave it up to
Rob/Krzysztof to decide if the board-id exception is warranted here or
not. :)
Thanks,
Stephan
^ permalink raw reply [flat|nested] 32+ messages in thread
* Re: [PATCH v3 5/8] arm64: dts: qcom: Add msm8939 SoC
2023-01-18 11:50 ` Bryan O'Donoghue
2023-01-18 12:50 ` Bryan O'Donoghue
@ 2023-01-18 17:33 ` Stephan Gerhold
2023-01-19 0:53 ` Bryan O'Donoghue
1 sibling, 1 reply; 32+ messages in thread
From: Stephan Gerhold @ 2023-01-18 17:33 UTC (permalink / raw)
To: Bryan O'Donoghue
Cc: agross, andersson, konrad.dybcio, djakov, robh+dt,
krzysztof.kozlowski+dt, linux-arm-msm, linux-pm, devicetree,
linux-kernel, benl, shawn.guo, fabien.parent, leo.yan,
dmitry.baryshkov, Jun Nie, James Willcox, Joseph Gates, Max Chen,
Zac Crosby, Vincent Knecht
On Wed, Jan 18, 2023 at 11:50:20AM +0000, Bryan O'Donoghue wrote:
> On 18/01/2023 09:59, Stephan Gerhold wrote:
> > On Tue, Jan 17, 2023 at 02:48:43AM +0000, Bryan O'Donoghue wrote:
> [...]
> > > + mdss: display-subsystem@1a00000 {
> > > + compatible = "qcom,mdss";
> > > + reg = <0x01a00000 0x1000>,
> > > + <0x01ac8000 0x3000>;
> > > + reg-names = "mdss_phys", "vbif_phys";
> > > +
> > > + interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
> > > + interrupt-controller;
> > > +
> > > + clocks = <&gcc GCC_MDSS_AHB_CLK>,
> > > + <&gcc GCC_MDSS_AXI_CLK>,
> > > + <&gcc GCC_MDSS_VSYNC_CLK>;
> > > + clock-names = "iface",
> > > + "bus",
> > > + "vsync";
> > > +
> > > + power-domains = <&gcc MDSS_GDSC>;
> > > +
> > > + #address-cells = <1>;
> > > + #size-cells = <1>;
> > > + #interrupt-cells = <1>;
> > > + ranges;
> > > +
> > > + mdp: display-controller@1a01000 {
> > > + compatible = "qcom,mdp5";
> > > + reg = <0x01a01000 0x89000>;
> > > + reg-names = "mdp_phys";
> > > +
> > > + interrupt-parent = <&mdss>;
> > > + interrupts = <0>;
> > > +
> > > + clocks = <&gcc GCC_MDSS_AHB_CLK>,
> > > + <&gcc GCC_MDSS_AXI_CLK>,
> > > + <&gcc GCC_MDSS_MDP_CLK>,
> > > + <&gcc GCC_MDSS_VSYNC_CLK>,
> > > + <&gcc GCC_MDP_TBU_CLK>,
> > > + <&gcc GCC_MDP_RT_TBU_CLK>;
> > > + clock-names = "iface",
> > > + "bus",
> > > + "core",
> > > + "vsync",
> > > + "tbu",
> > > + "tbu_rt";
> > > +
> > > + iommus = <&apps_iommu 4>;
> > > +
> > > + interconnects = <&snoc_mm MASTER_MDP_PORT0 &bimc SLAVE_EBI_CH0>,
> > > + <&snoc_mm MASTER_MDP_PORT1 &bimc SLAVE_EBI_CH0>,
> > > + <&pcnoc MASTER_SPDM &snoc SLAVE_IMEM>;
> > > + interconnect-names = "mdp0-mem", "mdp1-mem", "register-mem";
> >
> > As I mentioned a already in a direct email at some point, AFAIU adding
> > interconnects should be an [almost-] all or nothing step. If you only
> > add interconnects for MDP then everything else that needs bandwidth will
> > either break or only continue working as a mere side effect of MDP
> > voting for permanent high bandwidth.
>
> We did discuss that. You'll also recall we concluded we would have to revert
> this patch to make that happen.
>
> commit 76a748e2c1aa976d0c7fef872fa6ff93ce334a8a
> Author: Leo Yan <leo.yan@linaro.org>
> Date: Sat Apr 16 09:26:34 2022 +0800
>
> interconnect: qcom: msm8939: Use icc_sync_state
>
> but then why not revert for all of these SoCs too ?
>
> drivers/interconnect/qcom/msm8939.c: .sync_state = icc_sync_state,
> drivers/interconnect/qcom/msm8974.c: .sync_state = icc_sync_state,
> drivers/interconnect/qcom/msm8996.c: .sync_state = icc_sync_state,
> drivers/interconnect/qcom/osm-l3.c: .sync_state = icc_sync_state,
> drivers/interconnect/qcom/sc7180.c: .sync_state = icc_sync_state,
> drivers/interconnect/qcom/sc7280.c: .sync_state = icc_sync_state,
> drivers/interconnect/qcom/sc8180x.c: .sync_state = icc_sync_state,
> drivers/interconnect/qcom/sc8280xp.c: .sync_state = icc_sync_state,
> drivers/interconnect/qcom/sdm845.c: .sync_state = icc_sync_state,
> drivers/interconnect/qcom/sdx55.c: .sync_state = icc_sync_state,
> drivers/interconnect/qcom/sdx65.c: .sync_state = icc_sync_state,
> drivers/interconnect/qcom/sm6350.c: .sync_state = icc_sync_state,
>
> until such time as we have an all or nothing interconnect setup for each of
> those SoCs ?
>
> Yes I take your point "some peripherals will appear to work only as a result
> of the AHB vote the MDP casts here" but, that is a bug in the definition of
> that hypothetical peripheral.
>
> The MDP/display won't run without the interconnect here and the only way to
> pull it is to remove sync_state which begs the question why not pull
> sync_state for all SoCs without a perfect interconnect description ?
>
> I think that would be a retrograde step.
>
Most of the SoCs you list do have "interconnects" defined for most
components, which means the situation for them is quite a different
level. It's probably not necessary to have the interconnect setup
absolutely perfect before enabling it. However to avoid frustration for
people with slightly different board setups it should at the very least
cover more than one component.
Should the icc_sync_state() change be reverted for some of these SoCs?
If you ask me: Yes!
Perhaps a real example makes my concern more understandable: As I
mentioned, you rely on MDP providing the necessary bandwidth for the
entire system. This works fine in your case, but it can happen easily
that MDSS/MDP is not enabled at all, e.g.:
- On a board without display.
- During early bring-up: I usually start with UART, USB and SDHCI
before I even think about enabling the display.
I simulated this on the BQ Aquaris M5 (MSM8939) that has most
functionality set up already in postmarketOS. First the results without
any changes (interconnects enabled like in your patch here):
-> Boots into rootfs in about *18 seconds*, feels fine
Now I just disable MDSS in the device tree and boot again:
&mdss {
status = "disabled";
};
-> Boots into rootfs in about *80 seconds*, everything feels sluggish
This is 4 times the normal boot time, and nothing in dmesg tells me that
it's because I don't have display enabled. Someone porting a new device,
especially without UART, might have given up already before waiting so
long. Plus, what would I do to fix this on a board without display? :/
Now I try removing icc_sync_state:
-> Boots into rootfs in about 17 seconds, feels fine
IMO it is clear that adding icc_sync_state() too early is a bad idea,
and *will* break some setups.
Thanks,
Stephan
^ permalink raw reply [flat|nested] 32+ messages in thread
* Re: (subset) [PATCH v3 0/8] Add MSM8939 SoC support with two devices
2023-01-17 2:48 [PATCH v3 0/8] Add MSM8939 SoC support with two devices Bryan O'Donoghue
` (7 preceding siblings ...)
2023-01-17 2:48 ` [PATCH v3 8/8] arm64: dts: qcom: Add msm8939 Sony Xperia M4 Aqua Bryan O'Donoghue
@ 2023-01-18 22:50 ` Bjorn Andersson
8 siblings, 0 replies; 32+ messages in thread
From: Bjorn Andersson @ 2023-01-18 22:50 UTC (permalink / raw)
To: konrad.dybcio, robh+dt, bryan.odonoghue, krzysztof.kozlowski+dt,
djakov, agross
Cc: shawn.guo, dmitry.baryshkov, devicetree, fabien.parent, benl,
linux-pm, linux-arm-msm, linux-kernel, leo.yan
On Tue, 17 Jan 2023 02:48:38 +0000, Bryan O'Donoghue wrote:
> V3:
> - Happily I don't currently depend on any other series to be merged.
> Bjorn and Chanwoo picked up everything I need to unblock this series. ＼(^o^)／
>
> - Moves xo_board to RPM/PMIC clock gated CXO, not including rpmcc: obvs - Konrad/Bjorn
> - qcom,msm-id = <239 0> - left as in V2 valid according to Sony references - bod
> - cpu-release-addr - as stated below we rely on lk2nd to take the second cluster
> out of reset - bod
> - smem child node update - Konrad
> - Whitespace updates - Konrad
> - gpu no interconnect - Konrad - No bod
> - 19.2 MHz dropped from timer@b020000 - Konrad
> - Added vreg_dummy comment - Konrad
> - sdc_pins grouped - Konrad
> - startup-delay-us = <0> - left as is
> - bias - added no-bias - Konrad
> - :g/msmgpio/s//tlmm/g - Konrad
> - mdss/s//display-controller - Konrad
> - l11 set-load - Korad
>
> [...]
Applied, thanks!
[4/8] clk: qcom: smd-rpm: msm8936: Add PMIC gated RPM_SMD_XO_*
commit: d03de4179540e9cee6e3f664e1b65178f07bb612
Best regards,
--
Bjorn Andersson <andersson@kernel.org>
^ permalink raw reply [flat|nested] 32+ messages in thread
* Re: [PATCH v3 1/8] dt-bindings: arm: qcom: Document MSM8939 SoC binding
2023-01-18 8:47 ` Stephan Gerhold
2023-01-18 12:05 ` Bryan O'Donoghue
@ 2023-01-19 0:32 ` Bryan O'Donoghue
1 sibling, 0 replies; 32+ messages in thread
From: Bryan O'Donoghue @ 2023-01-19 0:32 UTC (permalink / raw)
To: Stephan Gerhold
Cc: agross, andersson, konrad.dybcio, djakov, robh+dt,
krzysztof.kozlowski+dt, linux-arm-msm, linux-pm, devicetree,
linux-kernel, benl, shawn.guo, fabien.parent, leo.yan,
dmitry.baryshkov, Krzysztof Kozlowski
On 18/01/2023 08:47, Stephan Gerhold wrote:
> If we don't support the original bootloaders in a usable way upstream
> then we should not add MSM8939 to the allow list of broken bootloaders
> either, in my opinion.
Yes but, a vendor could just as easily cherry-pick the spin-table
enabling lk2nd patches back to their lk implementation and begin to drop
the ongoing burden of supporting the LPM stuff.
We certainly do and should support booting stock lk. There's no sense in
setting the bar to upstream even higher by imposing a chainloaded
bootloader on our hypothetical new user.
The right thing to do is to enable the vanilla path but, give the user
the extra option.
---
bod
^ permalink raw reply [flat|nested] 32+ messages in thread
* Re: [PATCH v3 5/8] arm64: dts: qcom: Add msm8939 SoC
2023-01-18 17:33 ` Stephan Gerhold
@ 2023-01-19 0:53 ` Bryan O'Donoghue
0 siblings, 0 replies; 32+ messages in thread
From: Bryan O'Donoghue @ 2023-01-19 0:53 UTC (permalink / raw)
To: Stephan Gerhold
Cc: agross, andersson, konrad.dybcio, djakov, robh+dt,
krzysztof.kozlowski+dt, linux-arm-msm, linux-pm, devicetree,
linux-kernel, benl, shawn.guo, fabien.parent, leo.yan,
dmitry.baryshkov, Jun Nie, James Willcox, Joseph Gates, Max Chen,
Zac Crosby, Vincent Knecht
On 18/01/2023 17:33, Stephan Gerhold wrote:
> On Wed, Jan 18, 2023 at 11:50:20AM +0000, Bryan O'Donoghue wrote:
>> On 18/01/2023 09:59, Stephan Gerhold wrote:
>>> On Tue, Jan 17, 2023 at 02:48:43AM +0000, Bryan O'Donoghue wrote:
>> [...]
>>>> + mdss: display-subsystem@1a00000 {
>>>> + compatible = "qcom,mdss";
>>>> + reg = <0x01a00000 0x1000>,
>>>> + <0x01ac8000 0x3000>;
>>>> + reg-names = "mdss_phys", "vbif_phys";
>>>> +
>>>> + interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
>>>> + interrupt-controller;
>>>> +
>>>> + clocks = <&gcc GCC_MDSS_AHB_CLK>,
>>>> + <&gcc GCC_MDSS_AXI_CLK>,
>>>> + <&gcc GCC_MDSS_VSYNC_CLK>;
>>>> + clock-names = "iface",
>>>> + "bus",
>>>> + "vsync";
>>>> +
>>>> + power-domains = <&gcc MDSS_GDSC>;
>>>> +
>>>> + #address-cells = <1>;
>>>> + #size-cells = <1>;
>>>> + #interrupt-cells = <1>;
>>>> + ranges;
>>>> +
>>>> + mdp: display-controller@1a01000 {
>>>> + compatible = "qcom,mdp5";
>>>> + reg = <0x01a01000 0x89000>;
>>>> + reg-names = "mdp_phys";
>>>> +
>>>> + interrupt-parent = <&mdss>;
>>>> + interrupts = <0>;
>>>> +
>>>> + clocks = <&gcc GCC_MDSS_AHB_CLK>,
>>>> + <&gcc GCC_MDSS_AXI_CLK>,
>>>> + <&gcc GCC_MDSS_MDP_CLK>,
>>>> + <&gcc GCC_MDSS_VSYNC_CLK>,
>>>> + <&gcc GCC_MDP_TBU_CLK>,
>>>> + <&gcc GCC_MDP_RT_TBU_CLK>;
>>>> + clock-names = "iface",
>>>> + "bus",
>>>> + "core",
>>>> + "vsync",
>>>> + "tbu",
>>>> + "tbu_rt";
>>>> +
>>>> + iommus = <&apps_iommu 4>;
>>>> +
>>>> + interconnects = <&snoc_mm MASTER_MDP_PORT0 &bimc SLAVE_EBI_CH0>,
>>>> + <&snoc_mm MASTER_MDP_PORT1 &bimc SLAVE_EBI_CH0>,
>>>> + <&pcnoc MASTER_SPDM &snoc SLAVE_IMEM>;
>>>> + interconnect-names = "mdp0-mem", "mdp1-mem", "register-mem";
>>>
>>> As I mentioned a already in a direct email at some point, AFAIU adding
>>> interconnects should be an [almost-] all or nothing step. If you only
>>> add interconnects for MDP then everything else that needs bandwidth will
>>> either break or only continue working as a mere side effect of MDP
>>> voting for permanent high bandwidth.
>>
>> We did discuss that. You'll also recall we concluded we would have to revert
>> this patch to make that happen.
>>
>> commit 76a748e2c1aa976d0c7fef872fa6ff93ce334a8a
>> Author: Leo Yan <leo.yan@linaro.org>
>> Date: Sat Apr 16 09:26:34 2022 +0800
>>
>> interconnect: qcom: msm8939: Use icc_sync_state
>>
>> but then why not revert for all of these SoCs too ?
>>
>> drivers/interconnect/qcom/msm8939.c: .sync_state = icc_sync_state,
>> drivers/interconnect/qcom/msm8974.c: .sync_state = icc_sync_state,
>> drivers/interconnect/qcom/msm8996.c: .sync_state = icc_sync_state,
>> drivers/interconnect/qcom/osm-l3.c: .sync_state = icc_sync_state,
>> drivers/interconnect/qcom/sc7180.c: .sync_state = icc_sync_state,
>> drivers/interconnect/qcom/sc7280.c: .sync_state = icc_sync_state,
>> drivers/interconnect/qcom/sc8180x.c: .sync_state = icc_sync_state,
>> drivers/interconnect/qcom/sc8280xp.c: .sync_state = icc_sync_state,
>> drivers/interconnect/qcom/sdm845.c: .sync_state = icc_sync_state,
>> drivers/interconnect/qcom/sdx55.c: .sync_state = icc_sync_state,
>> drivers/interconnect/qcom/sdx65.c: .sync_state = icc_sync_state,
>> drivers/interconnect/qcom/sm6350.c: .sync_state = icc_sync_state,
>>
>> until such time as we have an all or nothing interconnect setup for each of
>> those SoCs ?
>>
>> Yes I take your point "some peripherals will appear to work only as a result
>> of the AHB vote the MDP casts here" but, that is a bug in the definition of
>> that hypothetical peripheral.
>>
>> The MDP/display won't run without the interconnect here and the only way to
>> pull it is to remove sync_state which begs the question why not pull
>> sync_state for all SoCs without a perfect interconnect description ?
>>
>> I think that would be a retrograde step.
>>
>
> Most of the SoCs you list do have "interconnects" defined for most
> components, which means the situation for them is quite a different
> level.
8974 defines two interconnects one for the mdp, one of the gpu. So a
headless setup as you describe would encounter the same situation
potentially.
> I simulated this on the BQ Aquaris M5 (MSM8939) that has most
> functionality set up already in postmarketOS. First the results without
> any changes (interconnects enabled like in your patch here):
To me, that is indicative of more work being required to vote
appropriately for required bandwidth - AHB clocks basically in our
hypothetical setup.
The display certainly won't work without voting for bandwidth it needs.
If there's work to be done to _enable_ headless mode - and there is, we
can do the work to figure out who isn't voting for bandwidth.
Probably the CPU - absent cpufreq, CPR, the operating points. A good -
probably correct guess is we aren't ramping cpufreq, aren't ramping CCI
and aren't voting for the inter-chip CCI "front side" so when the system
boots headless and "does stuff" the cpufrequency stays low, the votes
aren't cast and everything seems to crawl.
I still think its a contrived example though. CPR will come right after
the core dtsi and we can put the theory to the test.
;)
---
bod
^ permalink raw reply [flat|nested] 32+ messages in thread
* Re: [PATCH v3 5/8] arm64: dts: qcom: Add msm8939 SoC
2023-01-17 20:58 ` Bjorn Andersson
2023-01-17 22:48 ` Bryan O'Donoghue
@ 2023-01-20 0:40 ` Bryan O'Donoghue
2023-01-20 0:42 ` Bryan O'Donoghue
1 sibling, 1 reply; 32+ messages in thread
From: Bryan O'Donoghue @ 2023-01-20 0:40 UTC (permalink / raw)
To: Bjorn Andersson
Cc: agross, konrad.dybcio, djakov, robh+dt, krzysztof.kozlowski+dt,
linux-arm-msm, linux-pm, devicetree, linux-kernel, benl,
shawn.guo, fabien.parent, leo.yan, dmitry.baryshkov, Jun Nie,
James Willcox, Joseph Gates, Max Chen, Zac Crosby,
Vincent Knecht, Stephan Gerhold
On 17/01/2023 20:58, Bjorn Andersson wrote:
> Once the remote pulls the "handover" interrupt, it signals that it has
> cast the necessary votes and need no more hand-holding.
>
> So it's unlikely that _AO is the right choice here.
For the record here's the downstream _AO is what it says
pronto: wcnss@a204000 {
compatible = "qcom,pronto-v2-pd-pil", "qcom,pronto";
reg = <0x0a204000 0x2000>, <0x0a202000 0x1000>, <0x0a21b000
0x3000>;
power-domains = <&rpmpd MSM8939_VDDCX>,
<&rpmpd MSM8939_VDDMX_AO>;
power-domain-names = "vddcx", "vddmx";
};
---
bod
^ permalink raw reply [flat|nested] 32+ messages in thread
* Re: [PATCH v3 5/8] arm64: dts: qcom: Add msm8939 SoC
2023-01-20 0:40 ` Bryan O'Donoghue
@ 2023-01-20 0:42 ` Bryan O'Donoghue
2023-01-20 0:45 ` Bryan O'Donoghue
0 siblings, 1 reply; 32+ messages in thread
From: Bryan O'Donoghue @ 2023-01-20 0:42 UTC (permalink / raw)
To: Bjorn Andersson
Cc: agross, konrad.dybcio, djakov, robh+dt, krzysztof.kozlowski+dt,
linux-arm-msm, linux-pm, devicetree, linux-kernel, benl,
shawn.guo, fabien.parent, leo.yan, dmitry.baryshkov, Jun Nie,
James Willcox, Joseph Gates, Max Chen, Zac Crosby,
Vincent Knecht, Stephan Gerhold
On 20/01/2023 00:40, Bryan O'Donoghue wrote:
>
> pronto: wcnss@a204000 {
> compatible = "qcom,pronto-v2-pd-pil", "qcom,pronto";
> reg = <0x0a204000 0x2000>, <0x0a202000 0x1000>, <0x0a21b000
> 0x3000>;
>
> power-domains = <&rpmpd MSM8939_VDDCX>,
> <&rpmpd MSM8939_VDDMX_AO>;
> power-domain-names = "vddcx", "vddmx";
> };
>
> ---
> bod
Doh.
I opened the 4.19 kernel ... not 3.18
*facepalm*
^ permalink raw reply [flat|nested] 32+ messages in thread
* Re: [PATCH v3 5/8] arm64: dts: qcom: Add msm8939 SoC
2023-01-20 0:42 ` Bryan O'Donoghue
@ 2023-01-20 0:45 ` Bryan O'Donoghue
0 siblings, 0 replies; 32+ messages in thread
From: Bryan O'Donoghue @ 2023-01-20 0:45 UTC (permalink / raw)
To: Bjorn Andersson
Cc: agross, konrad.dybcio, djakov, robh+dt, krzysztof.kozlowski+dt,
linux-arm-msm, linux-pm, devicetree, linux-kernel, benl,
shawn.guo, fabien.parent, leo.yan, dmitry.baryshkov, Jun Nie,
James Willcox, Joseph Gates, Max Chen, Zac Crosby,
Vincent Knecht, Stephan Gerhold
On 20/01/2023 00:42, Bryan O'Donoghue wrote:
> On 20/01/2023 00:40, Bryan O'Donoghue wrote:
>>
>> pronto: wcnss@a204000 {
>> compatible = "qcom,pronto-v2-pd-pil", "qcom,pronto";
>> reg = <0x0a204000 0x2000>, <0x0a202000 0x1000>, <0x0a21b000
>> 0x3000>;
>>
>> power-domains = <&rpmpd MSM8939_VDDCX>,
>> <&rpmpd MSM8939_VDDMX_AO>;
>> power-domain-names = "vddcx", "vddmx";
>> };
>>
>> ---
>> bod
>
> Doh.
>
> I opened the 4.19 kernel ... not 3.18
>
> *facepalm*
But *this* is the downstream
qcom,wcnss-wlan@0a000000 {
compatible = "qcom,wcnss_wlan";
qcom,pronto-vddmx-supply = <&pm8916_l3_corner_ao>;
qcom,pronto-vddcx-supply = <&pm8916_s2_corner>;
};
it is an _ao
---
bod
^ permalink raw reply [flat|nested] 32+ messages in thread
* Re: [PATCH v3 5/8] arm64: dts: qcom: Add msm8939 SoC
2023-01-18 9:59 ` Stephan Gerhold
2023-01-18 11:50 ` Bryan O'Donoghue
@ 2023-01-21 22:57 ` Bryan O'Donoghue
1 sibling, 0 replies; 32+ messages in thread
From: Bryan O'Donoghue @ 2023-01-21 22:57 UTC (permalink / raw)
To: Stephan Gerhold
Cc: agross, andersson, konrad.dybcio, djakov, robh+dt,
krzysztof.kozlowski+dt, linux-arm-msm, linux-pm, devicetree,
linux-kernel, benl, shawn.guo, fabien.parent, leo.yan,
dmitry.baryshkov, Jun Nie, James Willcox, Joseph Gates, Max Chen,
Zac Crosby, Vincent Knecht
On 18/01/2023 09:59, Stephan Gerhold wrote:
> Why are you adding a dummy power domain here? IMO this would be better
> added together with CPR. Especially because I would expect two power
> domains here later ("mx", "cpr"). For cpufreq you also need to make
> votes for the "MSM8939_VDDMX" power domain.
Confirmed power-domain is a required property, dtbs check will complain
without it.
I'll leave further discussion on the format of CPR for the CPR series
but our working example supposes the below as a starting point.
I'm not aware of VDDMX in the CPR path but its not at this node.
CPU2: cpu@102 {
device_type = "cpu";
compatible = "arm,cortex-a53", "arm,armv8";
reg = <0x102>;
next-level-cache = <&L2_1>;
enable-method = "qcom,kpss-acc-v2";
qcom,acc = <&acc2>;
qcom,saw = <&saw2>;
clocks = <&apcs1>;
operating-points-v2 = <&cluster1_opp_table>;
power-domains = <&cpr>;
power-domain-names = "cpr";
#cooling-cells = <2>;
capacity-dmips-mhz = <1024>;
};
cluster1_opp_table: cluster1-opp-table {
compatible = "operating-points-v2-qcom-cpu";
opp-shared;
/* Used by qcom-cpufreq-nvmem.c */
nvmem-cells = <&cpr_efuse_speedbin_pvs>;
nvmem-cell-names = "cpr_efuse_speedbin_pvs";
opp-200000000 {
opp-hz = /bits/ 64 <200000000>;
opp-supported-hw = <0x3f>;
required-opps = <&cpr_opp3>;
};
opp-345600000 {
opp-hz = /bits/ 64 <345600000>;
opp-supported-hw = <0x3f>;
required-opps = <&cpr_opp3>;
};
};
cpr_opp_table: cpr-opp-table {
compatible = "operating-points-v2-qcom-level";
cpr_opp1: opp1 {
opp-hz = /bits/ 64 <200000000>;
opp-level = <1>;
qcom,opp-fuse-level = <1>;
};
cpr_opp2: opp2 {
opp-hz = /bits/ 64 <345600000>;
opp-level = <2>;
qcom,opp-fuse-level = <1>;
};
cpr_opp3: opp3 {
opp-hz = /bits/ 64 <400000000>;
opp-level = <3>;
qcom,opp-fuse-level = <1>;
};
};
/* etc */
};
---
bod
^ permalink raw reply [flat|nested] 32+ messages in thread
end of thread, other threads:[~2023-01-21 22:57 UTC | newest]
Thread overview: 32+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2023-01-17 2:48 [PATCH v3 0/8] Add MSM8939 SoC support with two devices Bryan O'Donoghue
2023-01-17 2:48 ` [PATCH v3 1/8] dt-bindings: arm: qcom: Document MSM8939 SoC binding Bryan O'Donoghue
2023-01-18 8:47 ` Stephan Gerhold
2023-01-18 12:05 ` Bryan O'Donoghue
2023-01-18 15:43 ` Stephan Gerhold
2023-01-19 0:32 ` Bryan O'Donoghue
2023-01-17 2:48 ` [PATCH v3 2/8] dt-bindings: soc: qcom: smd-rpm: Exclude MSM8936 from glink-channels Bryan O'Donoghue
2023-01-17 2:48 ` [PATCH v3 3/8] dt-bindings: interconnect: Exclude all non msm8939 from snoc-mm Bryan O'Donoghue
2023-01-17 11:04 ` Krzysztof Kozlowski
2023-01-17 2:48 ` [PATCH v3 4/8] clk: qcom: smd-rpm: msm8936: Add PMIC gated RPM_SMD_XO_* Bryan O'Donoghue
2023-01-18 13:49 ` Konrad Dybcio
2023-01-17 2:48 ` [PATCH v3 5/8] arm64: dts: qcom: Add msm8939 SoC Bryan O'Donoghue
2023-01-17 20:58 ` Bjorn Andersson
2023-01-17 22:48 ` Bryan O'Donoghue
2023-01-18 5:09 ` Bjorn Andersson
2023-01-20 0:40 ` Bryan O'Donoghue
2023-01-20 0:42 ` Bryan O'Donoghue
2023-01-20 0:45 ` Bryan O'Donoghue
2023-01-18 9:59 ` Stephan Gerhold
2023-01-18 11:50 ` Bryan O'Donoghue
2023-01-18 12:50 ` Bryan O'Donoghue
2023-01-18 17:33 ` Stephan Gerhold
2023-01-19 0:53 ` Bryan O'Donoghue
2023-01-21 22:57 ` Bryan O'Donoghue
2023-01-17 2:48 ` [PATCH v3 6/8] arm64: dts: qcom: Add msm8939-pm8916.dtsi include Bryan O'Donoghue
2023-01-18 13:49 ` Konrad Dybcio
2023-01-17 2:48 ` [PATCH v3 7/8] arm64: dts: qcom: Add Square apq8039-t2 board Bryan O'Donoghue
2023-01-17 21:06 ` Bjorn Andersson
2023-01-17 2:48 ` [PATCH v3 8/8] arm64: dts: qcom: Add msm8939 Sony Xperia M4 Aqua Bryan O'Donoghue
2023-01-18 14:42 ` Konrad Dybcio
2023-01-18 15:11 ` Bryan O'Donoghue
2023-01-18 22:50 ` (subset) [PATCH v3 0/8] Add MSM8939 SoC support with two devices Bjorn Andersson
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).