* [PATCH v2 1/3] dt-bindings: arm: amlogic: document Odroid-N2L
2023-01-25 8:18 [PATCH v2 0/3] arm64: meson-g12b: add initial support for Odroid-N2L Neil Armstrong
@ 2023-01-25 8:18 ` Neil Armstrong
2023-01-25 8:18 ` [PATCH v2 2/3] arm64: dts: meson-g12b: move common node into new odroid.dtsi Neil Armstrong
` (2 subsequent siblings)
3 siblings, 0 replies; 5+ messages in thread
From: Neil Armstrong @ 2023-01-25 8:18 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Kevin Hilman, Jerome Brunet,
Martin Blumenstingl
Cc: devicetree, linux-kernel, linux-arm-kernel, linux-amlogic,
Dongjin Kim, Neil Armstrong, Krzysztof Kozlowski
ODROID-N2L is a variant SBC in small form factor and some peripherals
are removed from ODROID-N2PLUS based on S922X SoC.
- On-board ethernet is removed
- On-board RTC is removed
- USB 3.0 hub is removed, so one USB 2.0 and one USB 3.0 host ports
are available
- Huge heatsink is replaced with 40x40mm heatsink, 5V active heatsink
is recommended or a tall passive sink is optional
- 3.5mm earjack is removed
- IR remote receiver is removed
- MIPI DSI port is added
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
Documentation/devicetree/bindings/arm/amlogic.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/arm/amlogic.yaml b/Documentation/devicetree/bindings/arm/amlogic.yaml
index e16b5fa55847..8aa6b6a92c29 100644
--- a/Documentation/devicetree/bindings/arm/amlogic.yaml
+++ b/Documentation/devicetree/bindings/arm/amlogic.yaml
@@ -165,6 +165,7 @@ properties:
- azw,gtking-pro
- hardkernel,odroid-go-ultra
- hardkernel,odroid-n2
+ - hardkernel,odroid-n2l
- hardkernel,odroid-n2-plus
- khadas,vim3
- ugoos,am6
--
2.34.1
^ permalink raw reply related [flat|nested] 5+ messages in thread* [PATCH v2 2/3] arm64: dts: meson-g12b: move common node into new odroid.dtsi
2023-01-25 8:18 [PATCH v2 0/3] arm64: meson-g12b: add initial support for Odroid-N2L Neil Armstrong
2023-01-25 8:18 ` [PATCH v2 1/3] dt-bindings: arm: amlogic: document Odroid-N2L Neil Armstrong
@ 2023-01-25 8:18 ` Neil Armstrong
2023-01-25 8:18 ` [PATCH v2 3/3] arm64: dts: meson-g12b-odroid: Add initial support for Hardkernel ODROID-N2L Neil Armstrong
2023-01-26 8:34 ` [PATCH v2 0/3] arm64: meson-g12b: add initial support for Odroid-N2L Neil Armstrong
3 siblings, 0 replies; 5+ messages in thread
From: Neil Armstrong @ 2023-01-25 8:18 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Kevin Hilman, Jerome Brunet,
Martin Blumenstingl
Cc: devicetree, linux-kernel, linux-arm-kernel, linux-amlogic,
Dongjin Kim, Neil Armstrong
In order to introduce Odroid-N2L which is basically an Odroid-N2+
without some on-board peripherals (Ethernet, RTC, Hub, Jack),
move the common nodes into a new meson-g12b-odroid.dtsi which will
will be the common dtsi for all the Odroid-N2 derived boards.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
.../boot/dts/amlogic/meson-g12b-odroid-n2.dtsi | 448 +--------------------
arch/arm64/boot/dts/amlogic/meson-g12b-odroid.dtsi | 445 ++++++++++++++++++++
2 files changed, 454 insertions(+), 439 deletions(-)
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi
index 667d2b774924..24d0442dffb2 100644
--- a/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi
@@ -4,17 +4,11 @@
* Author: Neil Armstrong <narmstrong@baylibre.com>
*/
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/gpio/meson-g12a-gpio.h>
-#include <dt-bindings/sound/meson-g12a-toacodec.h>
-#include <dt-bindings/sound/meson-g12a-tohdmitx.h>
+#include "meson-g12b-odroid.dtsi"
/ {
aliases {
- serial0 = &uart_AO;
- ethernet0 = ðmac;
rtc0 = &rtc;
- rtc1 = &vrtc;
};
dio2133: audio-amplifier-0 {
@@ -25,149 +19,6 @@ dio2133: audio-amplifier-0 {
status = "okay";
};
- chosen {
- stdout-path = "serial0:115200n8";
- };
-
- memory@0 {
- device_type = "memory";
- reg = <0x0 0x0 0x0 0x40000000>;
- };
-
- emmc_pwrseq: emmc-pwrseq {
- compatible = "mmc-pwrseq-emmc";
- reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>;
- };
-
- fan: gpio-fan {
- compatible = "gpio-fan";
- gpios = <&gpio_ao GPIOAO_10 GPIO_ACTIVE_HIGH>;
- /* Using Dummy Speed */
- gpio-fan,speed-map = <0 0>, <1 1>;
- #cooling-cells = <2>;
- };
-
- leds {
- compatible = "gpio-leds";
-
- led-blue {
- label = "n2:blue";
- gpios = <&gpio_ao GPIOAO_11 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "heartbeat";
- };
- };
-
- tflash_vdd: regulator-tflash_vdd {
- compatible = "regulator-fixed";
-
- regulator-name = "TFLASH_VDD";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
-
- gpio = <&gpio_ao GPIOAO_8 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- regulator-always-on;
- };
-
- tf_io: gpio-regulator-tf_io {
- compatible = "regulator-gpio";
-
- regulator-name = "TF_IO";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
-
- gpios = <&gpio_ao GPIOAO_9 GPIO_ACTIVE_HIGH>;
- gpios-states = <0>;
-
- states = <3300000 0>,
- <1800000 1>;
- };
-
- flash_1v8: regulator-flash_1v8 {
- compatible = "regulator-fixed";
- regulator-name = "FLASH_1V8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- vin-supply = <&vcc_3v3>;
- regulator-always-on;
- };
-
- main_12v: regulator-main_12v {
- compatible = "regulator-fixed";
- regulator-name = "12V";
- regulator-min-microvolt = <12000000>;
- regulator-max-microvolt = <12000000>;
- regulator-always-on;
- };
-
- vcc_5v: regulator-vcc_5v {
- compatible = "regulator-fixed";
- regulator-name = "5V";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- regulator-always-on;
- vin-supply = <&main_12v>;
- gpio = <&gpio GPIOH_8 GPIO_OPEN_DRAIN>;
- enable-active-high;
- };
-
- vcc_1v8: regulator-vcc_1v8 {
- compatible = "regulator-fixed";
- regulator-name = "VCC_1V8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- vin-supply = <&vcc_3v3>;
- regulator-always-on;
- };
-
- vcc_3v3: regulator-vcc_3v3 {
- compatible = "regulator-fixed";
- regulator-name = "VCC_3V3";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- vin-supply = <&vddao_3v3>;
- regulator-always-on;
- /* FIXME: actually controlled by VDDCPU_B_EN */
- };
-
- vddcpu_a: regulator-vddcpu-a {
- /*
- * MP8756GD Regulator.
- */
- compatible = "pwm-regulator";
-
- regulator-name = "VDDCPU_A";
- regulator-min-microvolt = <721000>;
- regulator-max-microvolt = <1022000>;
-
- pwm-supply = <&main_12v>;
-
- pwms = <&pwm_ab 0 1250 0>;
- pwm-dutycycle-range = <100 0>;
-
- regulator-boot-on;
- regulator-always-on;
- };
-
- vddcpu_b: regulator-vddcpu-b {
- /*
- * Silergy SY8120B1ABC Regulator.
- */
- compatible = "pwm-regulator";
-
- regulator-name = "VDDCPU_B";
- regulator-min-microvolt = <721000>;
- regulator-max-microvolt = <1022000>;
-
- pwm-supply = <&main_12v>;
-
- pwms = <&pwm_AO_cd 1 1250 0>;
- pwm-dutycycle-range = <100 0>;
-
- regulator-boot-on;
- regulator-always-on;
- };
-
hub_5v: regulator-hub_5v {
compatible = "regulator-fixed";
regulator-name = "HUB_5V";
@@ -180,47 +31,6 @@ hub_5v: regulator-hub_5v {
enable-active-high;
};
- usb_pwr_en: regulator-usb_pwr_en {
- compatible = "regulator-fixed";
- regulator-name = "USB_PWR_EN";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- vin-supply = <&vcc_5v>;
-
- /* Connected to the microUSB port power enable */
- gpio = <&gpio GPIOH_6 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- };
-
- vddao_1v8: regulator-vddao_1v8 {
- compatible = "regulator-fixed";
- regulator-name = "VDDAO_1V8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- vin-supply = <&vddao_3v3>;
- regulator-always-on;
- };
-
- vddao_3v3: regulator-vddao_3v3 {
- compatible = "regulator-fixed";
- regulator-name = "VDDAO_3V3";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- vin-supply = <&main_12v>;
- regulator-always-on;
- };
-
- hdmi-connector {
- compatible = "hdmi-connector";
- type = "a";
-
- port {
- hdmi_connector_in: endpoint {
- remote-endpoint = <&hdmi_tx_tmds_out>;
- };
- };
- };
-
sound {
compatible = "amlogic,axg-sound-card";
model = "ODROID-N2";
@@ -354,102 +164,13 @@ &acodec {
status = "okay";
};
-&arb {
- status = "okay";
-};
-
-&cec_AO {
- pinctrl-0 = <&cec_ao_a_h_pins>;
- pinctrl-names = "default";
- status = "disabled";
- hdmi-phandle = <&hdmi_tx>;
-};
-
-&cecb_AO {
- pinctrl-0 = <&cec_ao_b_h_pins>;
+ðmac {
+ pinctrl-0 = <ð_pins>, <ð_rgmii_pins>;
pinctrl-names = "default";
status = "okay";
- hdmi-phandle = <&hdmi_tx>;
-};
-
-&clkc_audio {
- status = "okay";
-};
-
-&cpu0 {
- cpu-supply = <&vddcpu_b>;
- operating-points-v2 = <&cpu_opp_table_0>;
- clocks = <&clkc CLKID_CPU_CLK>;
- clock-latency = <50000>;
-};
-
-&cpu1 {
- cpu-supply = <&vddcpu_b>;
- operating-points-v2 = <&cpu_opp_table_0>;
- clocks = <&clkc CLKID_CPU_CLK>;
- clock-latency = <50000>;
-};
-
-&cpu100 {
- cpu-supply = <&vddcpu_a>;
- operating-points-v2 = <&cpub_opp_table_1>;
- clocks = <&clkc CLKID_CPUB_CLK>;
- clock-latency = <50000>;
-};
-
-&cpu101 {
- cpu-supply = <&vddcpu_a>;
- operating-points-v2 = <&cpub_opp_table_1>;
- clocks = <&clkc CLKID_CPUB_CLK>;
- clock-latency = <50000>;
-};
-
-&cpu102 {
- cpu-supply = <&vddcpu_a>;
- operating-points-v2 = <&cpub_opp_table_1>;
- clocks = <&clkc CLKID_CPUB_CLK>;
- clock-latency = <50000>;
-};
-
-&cpu103 {
- cpu-supply = <&vddcpu_a>;
- operating-points-v2 = <&cpub_opp_table_1>;
- clocks = <&clkc CLKID_CPUB_CLK>;
- clock-latency = <50000>;
-};
-
-&cpu_thermal {
- trips {
- cpu_active: cpu-active {
- temperature = <60000>; /* millicelsius */
- hysteresis = <2000>; /* millicelsius */
- type = "active";
- };
- };
-
- cooling-maps {
- map {
- trip = <&cpu_active>;
- cooling-device = <&fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
- };
- };
-};
-
-&ddr_thermal {
- trips {
- ddr_active: ddr-active {
- temperature = <60000>; /* millicelsius */
- hysteresis = <2000>; /* millicelsius */
- type = "active";
- };
- };
-
- cooling-maps {
- map {
- trip = <&ddr_active>;
- cooling-device = <&fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
- };
- };
+ phy-mode = "rgmii";
+ phy-handle = <&external_phy>;
+ amlogic,tx-delay-ns = <2>;
};
&ext_mdio {
@@ -468,27 +189,6 @@ external_phy: ethernet-phy@0 {
};
};
-ðmac {
- pinctrl-0 = <ð_pins>, <ð_rgmii_pins>;
- pinctrl-names = "default";
- status = "okay";
- phy-mode = "rgmii";
- phy-handle = <&external_phy>;
- amlogic,tx-delay-ns = <2>;
-};
-
-&frddr_a {
- status = "okay";
-};
-
-&frddr_b {
- status = "okay";
-};
-
-&frddr_c {
- status = "okay";
-};
-
&gpio {
gpio-line-names =
/* GPIOZ */
@@ -549,26 +249,6 @@ hog-0 {
};
};
-&hdmi_tx {
- status = "okay";
- pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>;
- pinctrl-names = "default";
- hdmi-supply = <&vcc_5v>;
-};
-
-&hdmi_tx_tmds_port {
- hdmi_tx_tmds_out: endpoint {
- remote-endpoint = <&hdmi_connector_in>;
- };
-};
-
-&ir {
- status = "okay";
- pinctrl-0 = <&remote_input_ao_pins>;
- pinctrl-names = "default";
- linux,rc-map-name = "rc-odroid";
-};
-
&i2c3 {
status = "okay";
pinctrl-0 = <&i2c3_sda_a_pins>, <&i2c3_sck_a_pins>;
@@ -581,62 +261,11 @@ rtc: rtc@51 {
};
};
-&pwm_ab {
- pinctrl-0 = <&pwm_a_e_pins>;
- pinctrl-names = "default";
- clocks = <&xtal>;
- clock-names = "clkin0";
+&ir {
status = "okay";
-};
-
-&pwm_AO_cd {
- pinctrl-0 = <&pwm_ao_d_e_pins>;
+ pinctrl-0 = <&remote_input_ao_pins>;
pinctrl-names = "default";
- clocks = <&xtal>;
- clock-names = "clkin1";
- status = "okay";
-};
-
-&saradc {
- status = "okay";
- vref-supply = <&vddao_1v8>;
-};
-
-/* SD card */
-&sd_emmc_b {
- status = "okay";
- pinctrl-0 = <&sdcard_c_pins>;
- pinctrl-1 = <&sdcard_clk_gate_c_pins>;
- pinctrl-names = "default", "clk-gate";
-
- bus-width = <4>;
- cap-sd-highspeed;
- max-frequency = <50000000>;
- disable-wp;
-
- cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>;
- vmmc-supply = <&tflash_vdd>;
- vqmmc-supply = <&tf_io>;
-
-};
-
-/* eMMC */
-&sd_emmc_c {
- status = "okay";
- pinctrl-0 = <&emmc_ctrl_pins>, <&emmc_data_8b_pins>, <&emmc_ds_pins>;
- pinctrl-1 = <&emmc_clk_gate_pins>;
- pinctrl-names = "default", "clk-gate";
-
- bus-width = <8>;
- cap-mmc-highspeed;
- mmc-ddr-1_8v;
- mmc-hs200-1_8v;
- max-frequency = <200000000>;
- disable-wp;
-
- mmc-pwrseq = <&emmc_pwrseq>;
- vmmc-supply = <&vcc_3v3>;
- vqmmc-supply = <&flash_1v8>;
+ linux,rc-map-name = "rc-odroid";
};
/*
@@ -660,73 +289,14 @@ mx25u64: flash@0 {
};
};
-&tdmif_b {
- status = "okay";
-};
-
-&tdmif_c {
- status = "okay";
-};
-
-&tdmin_a {
- status = "okay";
-};
-
-&tdmin_b {
- status = "okay";
-};
-
-&tdmin_c {
- status = "okay";
-};
-
-&tdmin_lb {
- status = "okay";
-};
-
-&tdmout_b {
- status = "okay";
-};
-
-&tdmout_c {
- status = "okay";
-};
-
&toacodec {
status = "okay";
};
-&tohdmitx {
- status = "okay";
-};
-
-&toddr_a {
- status = "okay";
-};
-
-&toddr_b {
- status = "okay";
-};
-
-&toddr_c {
- status = "okay";
-};
-
-&uart_AO {
- status = "okay";
- pinctrl-0 = <&uart_ao_a_pins>;
- pinctrl-names = "default";
-};
-
&usb {
- status = "okay";
vbus-supply = <&usb_pwr_en>;
};
-&usb2_phy0 {
- phy-supply = <&vcc_5v>;
-};
-
&usb2_phy1 {
/* Enable the hub which is connected to this port */
phy-supply = <&hub_5v>;
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-odroid.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid.dtsi
new file mode 100644
index 000000000000..9e12a34b2840
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid.dtsi
@@ -0,0 +1,445 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 BayLibre, SAS
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ */
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/meson-g12a-gpio.h>
+#include <dt-bindings/sound/meson-g12a-toacodec.h>
+#include <dt-bindings/sound/meson-g12a-tohdmitx.h>
+
+/ {
+ aliases {
+ serial0 = &uart_AO;
+ ethernet0 = ðmac;
+ rtc1 = &vrtc;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x40000000>;
+ };
+
+ emmc_pwrseq: emmc-pwrseq {
+ compatible = "mmc-pwrseq-emmc";
+ reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>;
+ };
+
+ fan: gpio-fan {
+ compatible = "gpio-fan";
+ gpios = <&gpio_ao GPIOAO_10 GPIO_ACTIVE_HIGH>;
+ /* Using Dummy Speed */
+ gpio-fan,speed-map = <0 0>, <1 1>;
+ #cooling-cells = <2>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led-blue {
+ label = "n2:blue";
+ gpios = <&gpio_ao GPIOAO_11 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ tflash_vdd: regulator-tflash_vdd {
+ compatible = "regulator-fixed";
+
+ regulator-name = "TFLASH_VDD";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&gpio_ao GPIOAO_8 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-always-on;
+ };
+
+ tf_io: gpio-regulator-tf_io {
+ compatible = "regulator-gpio";
+
+ regulator-name = "TF_IO";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpios = <&gpio_ao GPIOAO_9 GPIO_ACTIVE_HIGH>;
+ gpios-states = <0>;
+
+ states = <3300000 0>,
+ <1800000 1>;
+ };
+
+ flash_1v8: regulator-flash_1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "FLASH_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vcc_3v3>;
+ regulator-always-on;
+ };
+
+ main_12v: regulator-main_12v {
+ compatible = "regulator-fixed";
+ regulator-name = "12V";
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ regulator-always-on;
+ };
+
+ usb_pwr_en: regulator-usb_pwr_en {
+ compatible = "regulator-fixed";
+ regulator-name = "USB_PWR_EN";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc_5v>;
+
+ /* Connected to the microUSB port power enable */
+ gpio = <&gpio GPIOH_6 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ vcc_5v: regulator-vcc_5v {
+ compatible = "regulator-fixed";
+ regulator-name = "5V";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ vin-supply = <&main_12v>;
+ gpio = <&gpio GPIOH_8 GPIO_OPEN_DRAIN>;
+ enable-active-high;
+ };
+
+ vcc_1v8: regulator-vcc_1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vcc_3v3>;
+ regulator-always-on;
+ };
+
+ vcc_3v3: regulator-vcc_3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vddao_3v3>;
+ regulator-always-on;
+ /* FIXME: actually controlled by VDDCPU_B_EN */
+ };
+
+ vddcpu_a: regulator-vddcpu-a {
+ /*
+ * MP8756GD Regulator.
+ */
+ compatible = "pwm-regulator";
+
+ regulator-name = "VDDCPU_A";
+ regulator-min-microvolt = <721000>;
+ regulator-max-microvolt = <1022000>;
+
+ pwm-supply = <&main_12v>;
+
+ pwms = <&pwm_ab 0 1250 0>;
+ pwm-dutycycle-range = <100 0>;
+
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vddcpu_b: regulator-vddcpu-b {
+ /*
+ * Silergy SY8120B1ABC Regulator.
+ */
+ compatible = "pwm-regulator";
+
+ regulator-name = "VDDCPU_B";
+ regulator-min-microvolt = <721000>;
+ regulator-max-microvolt = <1022000>;
+
+ pwm-supply = <&main_12v>;
+
+ pwms = <&pwm_AO_cd 1 1250 0>;
+ pwm-dutycycle-range = <100 0>;
+
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vddao_1v8: regulator-vddao_1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDAO_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vddao_3v3>;
+ regulator-always-on;
+ };
+
+ vddao_3v3: regulator-vddao_3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDAO_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&main_12v>;
+ regulator-always-on;
+ };
+
+ hdmi-connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_connector_in: endpoint {
+ remote-endpoint = <&hdmi_tx_tmds_out>;
+ };
+ };
+ };
+};
+
+&arb {
+ status = "okay";
+};
+
+&cec_AO {
+ pinctrl-0 = <&cec_ao_a_h_pins>;
+ pinctrl-names = "default";
+ status = "disabled";
+ hdmi-phandle = <&hdmi_tx>;
+};
+
+&cecb_AO {
+ pinctrl-0 = <&cec_ao_b_h_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ hdmi-phandle = <&hdmi_tx>;
+};
+
+&clkc_audio {
+ status = "okay";
+};
+
+&cpu0 {
+ cpu-supply = <&vddcpu_b>;
+ operating-points-v2 = <&cpu_opp_table_0>;
+ clocks = <&clkc CLKID_CPU_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu1 {
+ cpu-supply = <&vddcpu_b>;
+ operating-points-v2 = <&cpu_opp_table_0>;
+ clocks = <&clkc CLKID_CPU_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu100 {
+ cpu-supply = <&vddcpu_a>;
+ operating-points-v2 = <&cpub_opp_table_1>;
+ clocks = <&clkc CLKID_CPUB_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu101 {
+ cpu-supply = <&vddcpu_a>;
+ operating-points-v2 = <&cpub_opp_table_1>;
+ clocks = <&clkc CLKID_CPUB_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu102 {
+ cpu-supply = <&vddcpu_a>;
+ operating-points-v2 = <&cpub_opp_table_1>;
+ clocks = <&clkc CLKID_CPUB_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu103 {
+ cpu-supply = <&vddcpu_a>;
+ operating-points-v2 = <&cpub_opp_table_1>;
+ clocks = <&clkc CLKID_CPUB_CLK>;
+ clock-latency = <50000>;
+};
+
+&cpu_thermal {
+ trips {
+ cpu_active: cpu-active {
+ temperature = <60000>; /* millicelsius */
+ hysteresis = <2000>; /* millicelsius */
+ type = "active";
+ };
+ };
+
+ cooling-maps {
+ map {
+ trip = <&cpu_active>;
+ cooling-device = <&fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+};
+
+&ddr_thermal {
+ trips {
+ ddr_active: ddr-active {
+ temperature = <60000>; /* millicelsius */
+ hysteresis = <2000>; /* millicelsius */
+ type = "active";
+ };
+ };
+
+ cooling-maps {
+ map {
+ trip = <&ddr_active>;
+ cooling-device = <&fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+};
+
+&frddr_a {
+ status = "okay";
+};
+
+&frddr_b {
+ status = "okay";
+};
+
+&frddr_c {
+ status = "okay";
+};
+
+&hdmi_tx {
+ status = "okay";
+ pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>;
+ pinctrl-names = "default";
+ hdmi-supply = <&vcc_5v>;
+};
+
+&hdmi_tx_tmds_port {
+ hdmi_tx_tmds_out: endpoint {
+ remote-endpoint = <&hdmi_connector_in>;
+ };
+};
+
+&pwm_ab {
+ pinctrl-0 = <&pwm_a_e_pins>;
+ pinctrl-names = "default";
+ clocks = <&xtal>;
+ clock-names = "clkin0";
+ status = "okay";
+};
+
+&pwm_AO_cd {
+ pinctrl-0 = <&pwm_ao_d_e_pins>;
+ pinctrl-names = "default";
+ clocks = <&xtal>;
+ clock-names = "clkin1";
+ status = "okay";
+};
+
+&saradc {
+ status = "okay";
+ vref-supply = <&vddao_1v8>;
+};
+
+/* SD card */
+&sd_emmc_b {
+ status = "okay";
+ pinctrl-0 = <&sdcard_c_pins>;
+ pinctrl-1 = <&sdcard_clk_gate_c_pins>;
+ pinctrl-names = "default", "clk-gate";
+
+ bus-width = <4>;
+ cap-sd-highspeed;
+ max-frequency = <50000000>;
+ disable-wp;
+
+ cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>;
+ vmmc-supply = <&tflash_vdd>;
+ vqmmc-supply = <&tf_io>;
+
+};
+
+/* eMMC */
+&sd_emmc_c {
+ status = "okay";
+ pinctrl-0 = <&emmc_ctrl_pins>, <&emmc_data_8b_pins>, <&emmc_ds_pins>;
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
+
+ bus-width = <8>;
+ cap-mmc-highspeed;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+ max-frequency = <200000000>;
+ disable-wp;
+
+ mmc-pwrseq = <&emmc_pwrseq>;
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&flash_1v8>;
+};
+
+&tdmif_b {
+ status = "okay";
+};
+
+&tdmif_c {
+ status = "okay";
+};
+
+&tdmin_a {
+ status = "okay";
+};
+
+&tdmin_b {
+ status = "okay";
+};
+
+&tdmin_c {
+ status = "okay";
+};
+
+&tdmin_lb {
+ status = "okay";
+};
+
+&tdmout_b {
+ status = "okay";
+};
+
+&tdmout_c {
+ status = "okay";
+};
+
+&tohdmitx {
+ status = "okay";
+};
+
+&toddr_a {
+ status = "okay";
+};
+
+&toddr_b {
+ status = "okay";
+};
+
+&toddr_c {
+ status = "okay";
+};
+
+&uart_AO {
+ status = "okay";
+ pinctrl-0 = <&uart_ao_a_pins>;
+ pinctrl-names = "default";
+};
+
+&usb {
+ status = "okay";
+};
+
+&usb2_phy0 {
+ phy-supply = <&vcc_5v>;
+};
--
2.34.1
^ permalink raw reply related [flat|nested] 5+ messages in thread* [PATCH v2 3/3] arm64: dts: meson-g12b-odroid: Add initial support for Hardkernel ODROID-N2L
2023-01-25 8:18 [PATCH v2 0/3] arm64: meson-g12b: add initial support for Odroid-N2L Neil Armstrong
2023-01-25 8:18 ` [PATCH v2 1/3] dt-bindings: arm: amlogic: document Odroid-N2L Neil Armstrong
2023-01-25 8:18 ` [PATCH v2 2/3] arm64: dts: meson-g12b: move common node into new odroid.dtsi Neil Armstrong
@ 2023-01-25 8:18 ` Neil Armstrong
2023-01-26 8:34 ` [PATCH v2 0/3] arm64: meson-g12b: add initial support for Odroid-N2L Neil Armstrong
3 siblings, 0 replies; 5+ messages in thread
From: Neil Armstrong @ 2023-01-25 8:18 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Kevin Hilman, Jerome Brunet,
Martin Blumenstingl
Cc: devicetree, linux-kernel, linux-arm-kernel, linux-amlogic,
Dongjin Kim, Neil Armstrong
ODROID-N2L is a variant SBC in small form factor and some peripherals
are removed from ODROID-N2PLUS based on S922X SoC.
- On-board ethernet is removed
- On-board RTC is removed
- USB 3.0 hub is removed, so one USB 2.0 and one USB 3.0 host ports
are available
- Huge heatsink is replaced with 40x40mm heatsink, 5V active heatsink
is recommended or a tall passive sink is optional
- 3.5mm earjack is removed
- IR remote receiver is removed
- MIPI DSI port is added new but not yet supported
Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
arch/arm64/boot/dts/amlogic/Makefile | 1 +
.../boot/dts/amlogic/meson-g12b-odroid-n2l.dts | 125 +++++++++++++++++++++
2 files changed, 126 insertions(+)
diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
index 97b42e2100e0..04114e8c9992 100644
--- a/arch/arm64/boot/dts/amlogic/Makefile
+++ b/arch/arm64/boot/dts/amlogic/Makefile
@@ -15,6 +15,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-g12b-gtking.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-go-ultra.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2-plus.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2l.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12b-s922x-khadas-vim3.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-g12b-ugoos-am6.dtb
dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-kii-pro.dtb
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2l.dts b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2l.dts
new file mode 100644
index 000000000000..70919f40d597
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2l.dts
@@ -0,0 +1,125 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2022 Dongjin Kim <tobetter@gmail.com>
+ */
+
+/dts-v1/;
+
+/* The Amlogic S922X Rev. C supports the same OPPs as the A311D variant */
+#include "meson-g12b-a311d.dtsi"
+#include "meson-g12b-odroid.dtsi"
+
+/ {
+ compatible = "hardkernel,odroid-n2l", "amlogic,s922x", "amlogic,g12b";
+ model = "Hardkernel ODROID-N2L";
+
+ sound {
+ compatible = "amlogic,axg-sound-card";
+ model = "ODROID-N2L";
+ audio-aux-devs = <&tdmout_b>, <&tdmin_a>, <&tdmin_b>,
+ <&tdmin_c>, <&tdmin_lb>;
+ audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1",
+ "TDMOUT_B IN 1", "FRDDR_B OUT 1",
+ "TDMOUT_B IN 2", "FRDDR_C OUT 1",
+ "TDM_B Playback", "TDMOUT_B OUT",
+ "TDMIN_A IN 4", "TDM_B Loopback",
+ "TDMIN_B IN 4", "TDM_B Loopback",
+ "TDMIN_C IN 4", "TDM_B Loopback",
+ "TDMIN_LB IN 1", "TDM_B Loopback",
+ "TODDR_A IN 0", "TDMIN_A OUT",
+ "TODDR_B IN 0", "TDMIN_A OUT",
+ "TODDR_C IN 0", "TDMIN_A OUT",
+ "TODDR_A IN 1", "TDMIN_B OUT",
+ "TODDR_B IN 1", "TDMIN_B OUT",
+ "TODDR_C IN 1", "TDMIN_B OUT",
+ "TODDR_A IN 2", "TDMIN_C OUT",
+ "TODDR_B IN 2", "TDMIN_C OUT",
+ "TODDR_C IN 2", "TDMIN_C OUT",
+ "TODDR_A IN 6", "TDMIN_LB OUT",
+ "TODDR_B IN 6", "TDMIN_LB OUT",
+ "TODDR_C IN 6", "TDMIN_LB OUT";
+
+ assigned-clocks = <&clkc CLKID_MPLL2>,
+ <&clkc CLKID_MPLL0>,
+ <&clkc CLKID_MPLL1>;
+ assigned-clock-parents = <0>, <0>, <0>;
+ assigned-clock-rates = <294912000>,
+ <270950400>,
+ <393216000>;
+ status = "okay";
+
+ dai-link-0 {
+ sound-dai = <&frddr_a>;
+ };
+
+ dai-link-1 {
+ sound-dai = <&frddr_b>;
+ };
+
+ dai-link-2 {
+ sound-dai = <&frddr_c>;
+ };
+
+ dai-link-3 {
+ sound-dai = <&toddr_a>;
+ };
+
+ dai-link-4 {
+ sound-dai = <&toddr_b>;
+ };
+
+ dai-link-5 {
+ sound-dai = <&toddr_c>;
+ };
+
+ /* 8ch hdmi interface */
+ dai-link-6 {
+ sound-dai = <&tdmif_b>;
+ dai-format = "i2s";
+ dai-tdm-slot-tx-mask-0 = <1 1>;
+ dai-tdm-slot-tx-mask-1 = <1 1>;
+ dai-tdm-slot-tx-mask-2 = <1 1>;
+ dai-tdm-slot-tx-mask-3 = <1 1>;
+ mclk-fs = <256>;
+
+ codec {
+ sound-dai = <&tohdmitx TOHDMITX_I2S_IN_B>;
+ };
+ };
+
+ /* hdmi glue */
+ dai-link-7 {
+ sound-dai = <&tohdmitx TOHDMITX_I2S_OUT>;
+
+ codec {
+ sound-dai = <&hdmi_tx>;
+ };
+ };
+ };
+};
+
+ð_phy {
+ status = "disabled";
+};
+
+&vddcpu_a {
+ regulator-min-microvolt = <680000>;
+ regulator-max-microvolt = <1040000>;
+
+ pwms = <&pwm_ab 0 1500 0>;
+};
+
+&vddcpu_b {
+ regulator-min-microvolt = <680000>;
+ regulator-max-microvolt = <1040000>;
+
+ pwms = <&pwm_AO_cd 1 1500 0>;
+};
+
+&usb2_phy0 {
+ phy-supply = <&usb_pwr_en>;
+};
+
+&usb2_phy1 {
+ phy-supply = <&usb_pwr_en>;
+};
--
2.34.1
^ permalink raw reply related [flat|nested] 5+ messages in thread* Re: [PATCH v2 0/3] arm64: meson-g12b: add initial support for Odroid-N2L
2023-01-25 8:18 [PATCH v2 0/3] arm64: meson-g12b: add initial support for Odroid-N2L Neil Armstrong
` (2 preceding siblings ...)
2023-01-25 8:18 ` [PATCH v2 3/3] arm64: dts: meson-g12b-odroid: Add initial support for Hardkernel ODROID-N2L Neil Armstrong
@ 2023-01-26 8:34 ` Neil Armstrong
3 siblings, 0 replies; 5+ messages in thread
From: Neil Armstrong @ 2023-01-26 8:34 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Kevin Hilman, Jerome Brunet,
Martin Blumenstingl, Neil Armstrong
Cc: devicetree, linux-kernel, linux-arm-kernel, linux-amlogic,
Dongjin Kim, Krzysztof Kozlowski
Hi,
On Wed, 25 Jan 2023 09:18:36 +0100, Neil Armstrong wrote:
> ODROID-N2L is a variant SBC in small form factor and some peripherals
> are removed from ODROID-N2PLUS based on S922X SoC.
>
> - On-board ethernet is removed
> - On-board RTC is removed
> - USB 3.0 hub is removed, so one USB 2.0 and one USB 3.0 host ports
> are available
> - Huge heatsink is replaced with 40x40mm heatsink, 5V active heatsink
> is recommended or a tall passive sink is optional
> - 3.5mm earjack is removed
> - IR remote receiver is removed
> - MIPI DSI port is added
>
> [...]
Thanks, Applied to https://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux.git (v6.3/arm64-dt)
[1/3] dt-bindings: arm: amlogic: document Odroid-N2L
https://git.kernel.org/amlogic/c/8280a4ea1d7dd1d635c1ecdb9375b156e83358b9
[2/3] arm64: dts: meson-g12b: move common node into new odroid.dtsi
https://git.kernel.org/amlogic/c/379ae64609c7a3301b60483eb65bd8bc78f76328
[3/3] arm64: dts: meson-g12b-odroid: Add initial support for Hardkernel ODROID-N2L
https://git.kernel.org/amlogic/c/f1193c5c09b1bb6e214c804c7dd1c7fb07046631
These changes has been applied on the intermediate git tree [1].
The v6.3/arm64-dt branch will then be sent via a formal Pull Request to the Linux SoC maintainers
for inclusion in their intermediate git branches in order to be sent to Linus during
the next merge window, or sooner if it's a set of fixes.
In the cases of fixes, those will be merged in the current release candidate
kernel and as soon they appear on the Linux master branch they will be
backported to the previous Stable and Long-Stable kernels [2].
The intermediate git branches are merged daily in the linux-next tree [3],
people are encouraged testing these pre-release kernels and report issues on the
relevant mailing-lists.
If problems are discovered on those changes, please submit a signed-off-by revert
patch followed by a corrective changeset.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux.git
[2] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git
[3] https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git
--
Neil
^ permalink raw reply [flat|nested] 5+ messages in thread