[PATCH 1/3] arm64: dts: qcom: use generic node name for Bluetooth

[PATCH 1/3] arm64: dts: qcom: use generic node name for Bluetooth

[Krzysztof Kozlowski]

Node names should be generic (as Devicetree spec mandates), so use
"bluetooth" for BT node.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 arch/arm64/boot/dts/qcom/sc7180-idp.dts    | 2 +-
 arch/arm64/boot/dts/qcom/sdm845-cheza.dtsi | 2 +-
 2 files changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/sc7180-idp.dts b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
index 774f9d45f051..6ea8dd7d3e01 100644
--- a/arch/arm64/boot/dts/qcom/sc7180-idp.dts
+++ b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
@@ -430,7 +430,7 @@ &uart3 {
 	pinctrl-names = "default", "sleep";
 	pinctrl-1 = <&qup_uart3_sleep>;
 
-	bluetooth: wcn3990-bt {
+	bluetooth: bluetooth {
 		compatible = "qcom,wcn3990-bt";
 		vddio-supply = <&vreg_l10a_1p8>;
 		vddxo-supply = <&vreg_l1c_1p8>;
diff --git a/arch/arm64/boot/dts/qcom/sdm845-cheza.dtsi b/arch/arm64/boot/dts/qcom/sdm845-cheza.dtsi
index a78075155310..e19178c1ec44 100644
--- a/arch/arm64/boot/dts/qcom/sdm845-cheza.dtsi
+++ b/arch/arm64/boot/dts/qcom/sdm845-cheza.dtsi
@@ -862,7 +862,7 @@ &uart6 {
 
 	pinctrl-0 = <&qup_uart6_4pin>;
 
-	bluetooth: wcn3990-bt {
+	bluetooth: bluetooth {
 		compatible = "qcom,wcn3990-bt";
 		vddio-supply = <&src_pp1800_s4a>;
 		vddxo-supply = <&pp1800_l7a_wcn3990>;
-- 
2.34.1

[PATCH 2/3] arm64: dts: qcom: sm8350: drop incorrect cells from serial

[Krzysztof Kozlowski]

The serial/UART device node does not have children with unit addresses,
so adderss/size cells are not correct.

Fixes: cf03cd7e12bd ("arm64: dts: qcom: sm8350: Set up WRAP0 QUPs")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 arch/arm64/boot/dts/qcom/sm8350.dtsi | 2 --
 1 file changed, 2 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/sm8350.dtsi b/arch/arm64/boot/dts/qcom/sm8350.dtsi
index 4efe79985186..018f26f729f1 100644
--- a/arch/arm64/boot/dts/qcom/sm8350.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8350.dtsi
@@ -1031,8 +1031,6 @@ uart2: serial@98c000 {
 				interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
 				power-domains = <&rpmhpd SM8350_CX>;
 				operating-points-v2 = <&qup_opp_table_100mhz>;
-				#address-cells = <1>;
-				#size-cells = <0>;
 				status = "disabled";
 			};
 
-- 
2.34.1

[PATCH 3/3] arm64: dts: qcom: sm8450: drop incorrect cells from serial

[Krzysztof Kozlowski]

The serial/UART device node does not have children with unit addresses,
so adderss/size cells are not correct.

Fixes: f5837418479a ("arm64: dts: qcom: sm8450: add uart20 node")
Fixes: 5188049c9b36 ("arm64: dts: qcom: Add base SM8450 DTSI")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 arch/arm64/boot/dts/qcom/sm8450.dtsi | 4 ----
 1 file changed, 4 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/sm8450.dtsi b/arch/arm64/boot/dts/qcom/sm8450.dtsi
index d66dcd8fe61f..395a3a156e24 100644
--- a/arch/arm64/boot/dts/qcom/sm8450.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8450.dtsi
@@ -1017,8 +1017,6 @@ uart20: serial@894000 {
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_uart20_default>;
 				interrupts = <GIC_SPI 587 IRQ_TYPE_LEVEL_HIGH>;
-				#address-cells = <1>;
-				#size-cells = <0>;
 				status = "disabled";
 			};
 
@@ -1411,8 +1409,6 @@ uart7: serial@99c000 {
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_uart7_tx>, <&qup_uart7_rx>;
 				interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>;
-				#address-cells = <1>;
-				#size-cells = <0>;
 				status = "disabled";
 			};
 		};
-- 
2.34.1