[PATCH v6 0/2] leds: Add a driver for the BD2606MVV

[PATCH v6 0/2] leds: Add a driver for the BD2606MVV

[Andreas Kemnade]

Add the binding description and the corresponding driver for
the BD2606.

Changes in V6:
- comments about dealing with shared brightness registers
- comment about building as a module

Changes in V5:
- remove "driver" from the binding subject line
- avoid presenting shared brightness to the userspace
  by allowing only on/off in such cases.

Changes in V4:
- minor tuning of description in bindings
 
Changes in V3:
- binding cleanup
- move active variable from long-living struct onto stack

Changes in V2:
- Add Datasheet link
- use fwnode api
- remove childnode count check, that will bail out
  anyways later.
- add enable-gpios to binding but not to driver due to lack of
  testing ability

Andreas Kemnade (2):
  dt-bindings: leds: Add ROHM BD2606MVV LED
  leds: bd2606mvv: Driver for the Rohm 6 Channel i2c LED driver

 .../bindings/leds/rohm,bd2606mvv.yaml         |  81 +++++++++
 drivers/leds/Kconfig                          |  14 ++
 drivers/leds/Makefile                         |   1 +
 drivers/leds/leds-bd2606mvv.c                 | 160 ++++++++++++++++++
 4 files changed, 256 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/leds/rohm,bd2606mvv.yaml
 create mode 100644 drivers/leds/leds-bd2606mvv.c

-- 
2.39.2

[PATCH v6 1/2] dt-bindings: leds: Add ROHM BD2606MVV LED

[Andreas Kemnade]

Document ROHM BD2606MVV LED driver devicetree bindings.

Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: Matti Vaittinen <mazziesaccount@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
---
 .../bindings/leds/rohm,bd2606mvv.yaml         | 81 +++++++++++++++++++
 1 file changed, 81 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/leds/rohm,bd2606mvv.yaml

diff --git a/Documentation/devicetree/bindings/leds/rohm,bd2606mvv.yaml b/Documentation/devicetree/bindings/leds/rohm,bd2606mvv.yaml
new file mode 100644
index 0000000000000..14700a2e5feaa
--- /dev/null
+++ b/Documentation/devicetree/bindings/leds/rohm,bd2606mvv.yaml
@@ -0,0 +1,81 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/leds/rohm,bd2606mvv.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: ROHM BD2606MVV LED controller
+
+maintainers:
+  - Andreas Kemnade <andreas@kemnade.info>
+
+description:
+  The BD2606 MVV is a programmable LED controller connected via I2C that can
+  drive 6 separate lines. Each of them can be individually switched on and off,
+  but the brightness setting is shared between pairs of them.
+
+  Datasheet is available at
+  https://fscdn.rohm.com/en/products/databook/datasheet/ic/power/led_driver/bd2606mvv_1-e.pdf
+
+properties:
+  compatible:
+    const: rohm,bd2606mvv
+
+  reg:
+    maxItems: 1
+
+  "#address-cells":
+    const: 1
+
+  "#size-cells":
+    const: 0
+
+  enable-gpios:
+    maxItems: 1
+    description: GPIO pin to enable/disable the device.
+
+patternProperties:
+  "^led@[0-6]$":
+    type: object
+    $ref: common.yaml#
+    unevaluatedProperties: false
+
+    properties:
+      reg:
+        minimum: 0
+        maximum: 6
+
+    required:
+      - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/leds/common.h>
+
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        led-controller@66 {
+            compatible = "rohm,bd2606mvv";
+            reg = <0x66>;
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            led@0 {
+                reg = <0x0>;
+                color = <LED_COLOR_ID_RED>;
+                function = LED_FUNCTION_POWER;
+            };
+
+            led@2 {
+                reg = <0x2>;
+                color = <LED_COLOR_ID_WHITE>;
+                function = LED_FUNCTION_STATUS;
+            };
+        };
+    };
+
+...
-- 
2.39.2

[PATCH v6 2/2] leds: bd2606mvv: Driver for the Rohm 6 Channel i2c LED driver

[Andreas Kemnade]

The device provides 6 channels which can be individually
turned off and on but groups of two channels share a common brightness
register.

Limitation: The GPIO to enable the device is not used yet.

Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: Matti Vaittinen <mazziesaccount@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
---
 drivers/leds/Kconfig          |  14 +++
 drivers/leds/Makefile         |   1 +
 drivers/leds/leds-bd2606mvv.c | 160 ++++++++++++++++++++++++++++++++++
 3 files changed, 175 insertions(+)
 create mode 100644 drivers/leds/leds-bd2606mvv.c

diff --git a/drivers/leds/Kconfig b/drivers/leds/Kconfig
index 9dbce09eabacf..09afc56f54f16 100644
--- a/drivers/leds/Kconfig
+++ b/drivers/leds/Kconfig
@@ -551,6 +551,20 @@ config LEDS_REGULATOR
 	help
 	  This option enables support for regulator driven LEDs.
 
+config LEDS_BD2606MVV
+	tristate "LED driver for BD2606MVV"
+	depends on LEDS_CLASS
+	depends on I2C
+	select REGMAP_I2C
+	help
+	  This option enables support for BD2606MVV LED driver chips
+	  accessed via the I2C bus. It supports setting brightness, with
+	  the limitiation that there are groups of two channels sharing
+	  a brightness setting, but not the on/off setting.
+
+	  To compile this driver as a module, choose M here: the module will
+	  be called leds-bd2606mvv.
+
 config LEDS_BD2802
 	tristate "LED driver for BD2802 RGB LED"
 	depends on LEDS_CLASS
diff --git a/drivers/leds/Makefile b/drivers/leds/Makefile
index d30395d11fd84..c07d1512c745a 100644
--- a/drivers/leds/Makefile
+++ b/drivers/leds/Makefile
@@ -17,6 +17,7 @@ obj-$(CONFIG_LEDS_ARIEL)		+= leds-ariel.o
 obj-$(CONFIG_LEDS_AW2013)		+= leds-aw2013.o
 obj-$(CONFIG_LEDS_BCM6328)		+= leds-bcm6328.o
 obj-$(CONFIG_LEDS_BCM6358)		+= leds-bcm6358.o
+obj-$(CONFIG_LEDS_BD2606MVV)		+= leds-bd2606mvv.o
 obj-$(CONFIG_LEDS_BD2802)		+= leds-bd2802.o
 obj-$(CONFIG_LEDS_BLINKM)		+= leds-blinkm.o
 obj-$(CONFIG_LEDS_CLEVO_MAIL)		+= leds-clevo-mail.o
diff --git a/drivers/leds/leds-bd2606mvv.c b/drivers/leds/leds-bd2606mvv.c
new file mode 100644
index 0000000000000..76f9d4d70f9a6
--- /dev/null
+++ b/drivers/leds/leds-bd2606mvv.c
@@ -0,0 +1,160 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2023 Andreas Kemnade
+ *
+ * Datasheet:
+ * https://fscdn.rohm.com/en/products/databook/datasheet/ic/power/led_driver/bd2606mvv_1-e.pdf
+ *
+ * If LED brightness cannot be controlled independently due to shared
+ * brightness registers, max_brightness is set to 1 and only on/off
+ * is possible for the affected LED pair.
+ */
+
+#include <linux/i2c.h>
+#include <linux/leds.h>
+#include <linux/module.h>
+#include <linux/mod_devicetable.h>
+#include <linux/property.h>
+#include <linux/regmap.h>
+#include <linux/slab.h>
+
+#define BD2606_MAX_LEDS 6
+#define BD2606_MAX_BRIGHTNESS 63
+#define BD2606_REG_PWRCNT 3
+#define ldev_to_led(c)	container_of(c, struct bd2606mvv_led, ldev)
+
+struct bd2606mvv_led {
+	unsigned int led_no;
+	struct led_classdev ldev;
+	struct bd2606mvv_priv *priv;
+};
+
+struct bd2606mvv_priv {
+	struct bd2606mvv_led leds[BD2606_MAX_LEDS];
+	struct regmap *regmap;
+};
+
+static int
+bd2606mvv_brightness_set(struct led_classdev *led_cdev,
+		      enum led_brightness brightness)
+{
+	struct bd2606mvv_led *led = ldev_to_led(led_cdev);
+	struct bd2606mvv_priv *priv = led->priv;
+	int err;
+
+	if (brightness == 0)
+		return regmap_update_bits(priv->regmap,
+					  BD2606_REG_PWRCNT,
+					  1 << led->led_no,
+					  0);
+
+	/* shared brightness register */
+	err = regmap_write(priv->regmap, led->led_no / 2,
+			   led_cdev->max_brightness == 1 ?
+			   BD2606_MAX_BRIGHTNESS : brightness);
+	if (err)
+		return err;
+
+	return regmap_update_bits(priv->regmap,
+				  BD2606_REG_PWRCNT,
+				  1 << led->led_no,
+				  1 << led->led_no);
+}
+
+static const struct regmap_config bd2606mvv_regmap = {
+	.reg_bits = 8,
+	.val_bits = 8,
+	.max_register = 0x3,
+};
+
+static int bd2606mvv_probe(struct i2c_client *client)
+{
+	struct fwnode_handle *np, *child;
+	struct device *dev = &client->dev;
+	struct bd2606mvv_priv *priv;
+	struct fwnode_handle *led_fwnodes[BD2606_MAX_LEDS] = { 0 };
+	int active_pairs[BD2606_MAX_LEDS / 2] = { 0 };
+	int err, reg;
+	int i;
+
+	np = dev_fwnode(dev);
+	if (!np)
+		return -ENODEV;
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	priv->regmap = devm_regmap_init_i2c(client, &bd2606mvv_regmap);
+	if (IS_ERR(priv->regmap)) {
+		err = PTR_ERR(priv->regmap);
+		dev_err(dev, "Failed to allocate register map: %d\n", err);
+		return err;
+	}
+
+	i2c_set_clientdata(client, priv);
+
+	fwnode_for_each_available_child_node(np, child) {
+		struct bd2606mvv_led *led;
+
+		err = fwnode_property_read_u32(child, "reg", &reg);
+		if (err) {
+			fwnode_handle_put(child);
+			return err;
+		}
+		if (reg < 0 || reg >= BD2606_MAX_LEDS || led_fwnodes[reg]) {
+			fwnode_handle_put(child);
+			return -EINVAL;
+		}
+		led = &priv->leds[reg];
+		led_fwnodes[reg] = child;
+		active_pairs[reg / 2]++;
+		led->priv = priv;
+		led->led_no = reg;
+		led->ldev.brightness_set_blocking = bd2606mvv_brightness_set;
+		led->ldev.max_brightness = BD2606_MAX_BRIGHTNESS;
+	}
+
+	for (i = 0; i < BD2606_MAX_LEDS; i++) {
+		struct led_init_data init_data = {};
+
+		if (!led_fwnodes[i])
+			continue;
+
+		init_data.fwnode = led_fwnodes[i];
+		/* Check whether brightness can be independently adjusted. */
+		if (active_pairs[i / 2] == 2)
+			priv->leds[i].ldev.max_brightness = 1;
+
+		err = devm_led_classdev_register_ext(dev,
+						     &priv->leds[i].ldev,
+						     &init_data);
+		if (err < 0) {
+			fwnode_handle_put(child);
+			return dev_err_probe(dev, err,
+					     "couldn't register LED %s\n",
+					     priv->leds[i].ldev.name);
+		}
+	}
+	return 0;
+}
+
+static const struct of_device_id __maybe_unused of_bd2606mvv_leds_match[] = {
+	{ .compatible = "rohm,bd2606mvv", },
+	{},
+};
+MODULE_DEVICE_TABLE(of, of_bd2606mvv_leds_match);
+
+static struct i2c_driver bd2606mvv_driver = {
+	.driver   = {
+		.name    = "leds-bd2606mvv",
+		.of_match_table = of_match_ptr(of_bd2606mvv_leds_match),
+	},
+	.probe_new = bd2606mvv_probe,
+};
+
+module_i2c_driver(bd2606mvv_driver);
+
+MODULE_AUTHOR("Andreas Kemnade <andreas@kemnade.info>");
+MODULE_DESCRIPTION("BD2606 LED driver");
+MODULE_LICENSE("GPL");
-- 
2.39.2

Re: [PATCH v6 1/2] dt-bindings: leds: Add ROHM BD2606MVV LED

[Lee Jones]

On Wed, 19 Apr 2023, Andreas Kemnade wrote:

> Document ROHM BD2606MVV LED driver devicetree bindings.
> 
> Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
> Reviewed-by: Matti Vaittinen <mazziesaccount@gmail.com>
> Reviewed-by: Rob Herring <robh@kernel.org>
> ---
>  .../bindings/leds/rohm,bd2606mvv.yaml         | 81 +++++++++++++++++++
>  1 file changed, 81 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/leds/rohm,bd2606mvv.yaml

Applied, thanks

-- 
Lee Jones [李琼斯]

Re: [PATCH v6 2/2] leds: bd2606mvv: Driver for the Rohm 6 Channel i2c LED driver

[Lee Jones]

On Wed, 19 Apr 2023, Andreas Kemnade wrote:

> The device provides 6 channels which can be individually
> turned off and on but groups of two channels share a common brightness
> register.
> 
> Limitation: The GPIO to enable the device is not used yet.
> 
> Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
> Reviewed-by: Matti Vaittinen <mazziesaccount@gmail.com>
> Acked-by: Pavel Machek <pavel@ucw.cz>
> ---
>  drivers/leds/Kconfig          |  14 +++
>  drivers/leds/Makefile         |   1 +
>  drivers/leds/leds-bd2606mvv.c | 160 ++++++++++++++++++++++++++++++++++
>  3 files changed, 175 insertions(+)
>  create mode 100644 drivers/leds/leds-bd2606mvv.c

Applied, thanks

-- 
Lee Jones [李琼斯]

Re: [PATCH v6 2/2] leds: bd2606mvv: Driver for the Rohm 6 Channel i2c LED driver

[Andreas Kemnade]

On Mon, 24 Apr 2023 14:17:40 +0100
Lee Jones <lee@kernel.org> wrote:

> On Wed, 19 Apr 2023, Andreas Kemnade wrote:
> 
> > The device provides 6 channels which can be individually
> > turned off and on but groups of two channels share a common brightness
> > register.
> > 
> > Limitation: The GPIO to enable the device is not used yet.
> > 
> > Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
> > Reviewed-by: Matti Vaittinen <mazziesaccount@gmail.com>
> > Acked-by: Pavel Machek <pavel@ucw.cz>
> > ---
> >  drivers/leds/Kconfig          |  14 +++
> >  drivers/leds/Makefile         |   1 +
> >  drivers/leds/leds-bd2606mvv.c | 160 ++++++++++++++++++++++++++++++++++
> >  3 files changed, 175 insertions(+)
> >  create mode 100644 drivers/leds/leds-bd2606mvv.c  
> 
> Applied, thanks
> 
contrary to the binding doc, it does not appear on
https://git.kernel.org/pub/scm/linux/kernel/git/lee/leds.git/log/?h=for-leds-next

Any problems with applying it?

Regards,
Andreas

Re: [PATCH v6 2/2] leds: bd2606mvv: Driver for the Rohm 6 Channel i2c LED driver

[Lee Jones]

On Mon, 24 Apr 2023, Andreas Kemnade wrote:

> On Mon, 24 Apr 2023 14:17:40 +0100
> Lee Jones <lee@kernel.org> wrote:
> 
> > On Wed, 19 Apr 2023, Andreas Kemnade wrote:
> > 
> > > The device provides 6 channels which can be individually
> > > turned off and on but groups of two channels share a common brightness
> > > register.
> > > 
> > > Limitation: The GPIO to enable the device is not used yet.
> > > 
> > > Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
> > > Reviewed-by: Matti Vaittinen <mazziesaccount@gmail.com>
> > > Acked-by: Pavel Machek <pavel@ucw.cz>
> > > ---
> > >  drivers/leds/Kconfig          |  14 +++
> > >  drivers/leds/Makefile         |   1 +
> > >  drivers/leds/leds-bd2606mvv.c | 160 ++++++++++++++++++++++++++++++++++
> > >  3 files changed, 175 insertions(+)
> > >  create mode 100644 drivers/leds/leds-bd2606mvv.c  
> > 
> > Applied, thanks
> > 
> contrary to the binding doc, it does not appear on
> https://git.kernel.org/pub/scm/linux/kernel/git/lee/leds.git/log/?h=for-leds-next
> 
> Any problems with applying it?

Now applied to the correct branch, thanks.

-- 
Lee Jones [李琼斯]