From: Samin Guo <samin.guo@starfivetech.com>
To: <linux-kernel@vger.kernel.org>, <devicetree@vger.kernel.org>,
<netdev@vger.kernel.org>, Peter Geis <pgwipeout@gmail.com>,
Frank <Frank.Sae@motor-comm.com>
Cc: "David S . Miller" <davem@davemloft.net>,
Eric Dumazet <edumazet@google.com>,
Jakub Kicinski <kuba@kernel.org>, Paolo Abeni <pabeni@redhat.com>,
Rob Herring <robh+dt@kernel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
Andrew Lunn <andrew@lunn.ch>,
"Heiner Kallweit" <hkallweit1@gmail.com>,
Russell King <linux@armlinux.org.uk>,
"Samin Guo" <samin.guo@starfivetech.com>,
Yanhong Wang <yanhong.wang@starfivetech.com>
Subject: [PATCH v3 2/2] net: phy: motorcomm: Add pad drive strength cfg support
Date: Fri, 26 May 2023 17:05:02 +0800 [thread overview]
Message-ID: <20230526090502.29835-3-samin.guo@starfivetech.com> (raw)
In-Reply-To: <20230526090502.29835-1-samin.guo@starfivetech.com>
The motorcomm phy (YT8531) supports the ability to adjust the drive
strength of the rx_clk/rx_data, and the default strength may not be
suitable for all boards. So add configurable options to better match
the boards.(e.g. StarFive VisionFive 2)
Signed-off-by: Samin Guo <samin.guo@starfivetech.com>
---
drivers/net/phy/motorcomm.c | 46 +++++++++++++++++++++++++++++++++++++
1 file changed, 46 insertions(+)
diff --git a/drivers/net/phy/motorcomm.c b/drivers/net/phy/motorcomm.c
index 2fa5a90e073b..e5d6b491046e 100644
--- a/drivers/net/phy/motorcomm.c
+++ b/drivers/net/phy/motorcomm.c
@@ -236,6 +236,15 @@
*/
#define YTPHY_WCR_TYPE_PULSE BIT(0)
+#define YTPHY_PAD_DRIVE_STRENGTH_REG 0xA010
+#define YT8531_RGMII_RXC_DS_DEFAULT 0x3
+#define YT8531_RGMII_RXC_DS_MAX 0x7
+#define YT8531_RGMII_RXC_DS GENMASK(15, 13)
+#define YT8531_RGMII_RXD_DS_DEFAULT 0x3
+#define YT8531_RGMII_RXD_DS_MAX 0x7
+#define YT8531_RGMII_RXD_DS_LOW GENMASK(5, 4) /* Bit 1/0 of rxd_ds */
+#define YT8531_RGMII_RXD_DS_HI BIT(12) /* Bit 2 of rxd_ds */
+
#define YTPHY_SYNCE_CFG_REG 0xA012
#define YT8521_SCR_SYNCE_ENABLE BIT(5)
/* 1b0 output 25m clock
@@ -1494,6 +1503,7 @@ static int yt8521_config_init(struct phy_device *phydev)
static int yt8531_config_init(struct phy_device *phydev)
{
struct device_node *node = phydev->mdio.dev.of_node;
+ u32 ds, val;
int ret;
ret = ytphy_rgmii_clk_delay_config_with_lock(phydev);
@@ -1518,6 +1528,42 @@ static int yt8531_config_init(struct phy_device *phydev)
return ret;
}
+ ds = YT8531_RGMII_RXC_DS_DEFAULT;
+ if (!of_property_read_u32(node, "motorcomm,rx-clk-driver-strength", &val)) {
+ if (val > YT8531_RGMII_RXC_DS_MAX)
+ return -EINVAL;
+
+ ds = val;
+ }
+
+ ret = ytphy_modify_ext_with_lock(phydev,
+ YTPHY_PAD_DRIVE_STRENGTH_REG,
+ YT8531_RGMII_RXC_DS,
+ FIELD_PREP(YT8531_RGMII_RXC_DS, ds));
+ if (ret < 0)
+ return ret;
+
+ ds = FIELD_PREP(YT8531_RGMII_RXD_DS_LOW, YT8531_RGMII_RXD_DS_DEFAULT);
+ if (!of_property_read_u32(node, "motorcomm,rx-data-driver-strength", &val)) {
+ if (val > YT8531_RGMII_RXD_DS_MAX)
+ return -EINVAL;
+
+ if (val > FIELD_MAX(YT8531_RGMII_RXD_DS_LOW)) {
+ ds = val & FIELD_MAX(YT8531_RGMII_RXD_DS_LOW);
+ ds = FIELD_PREP(YT8531_RGMII_RXD_DS_LOW, ds);
+ ds |= YT8531_RGMII_RXD_DS_HI;
+ } else {
+ ds = FIELD_PREP(YT8531_RGMII_RXD_DS_LOW, val);
+ }
+ }
+
+ ret = ytphy_modify_ext_with_lock(phydev,
+ YTPHY_PAD_DRIVE_STRENGTH_REG,
+ YT8531_RGMII_RXD_DS_LOW | YT8531_RGMII_RXD_DS_HI,
+ ds);
+ if (ret < 0)
+ return ret;
+
return 0;
}
--
2.17.1
prev parent reply other threads:[~2023-05-26 9:05 UTC|newest]
Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-05-26 9:05 [PATCH v3 0/2] Add motorcomm phy pad-driver-strength-cfg support Samin Guo
2023-05-26 9:05 ` [PATCH v3 1/2] dt-bindings: net: motorcomm: Add pad driver strength cfg Samin Guo
2023-05-26 19:41 ` Conor Dooley
2023-05-29 3:46 ` Guo Samin
2023-06-20 3:09 ` Guo Samin
2023-06-20 8:26 ` Conor Dooley
2023-06-20 8:55 ` Krzysztof Kozlowski
2023-06-21 3:03 ` Guo Samin
2023-06-20 13:29 ` Andrew Lunn
2023-06-21 3:28 ` Guo Samin
2023-06-21 14:13 ` Andrew Lunn
2023-05-26 9:05 ` Samin Guo [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20230526090502.29835-3-samin.guo@starfivetech.com \
--to=samin.guo@starfivetech.com \
--cc=Frank.Sae@motor-comm.com \
--cc=andrew@lunn.ch \
--cc=davem@davemloft.net \
--cc=devicetree@vger.kernel.org \
--cc=edumazet@google.com \
--cc=hkallweit1@gmail.com \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=kuba@kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux@armlinux.org.uk \
--cc=netdev@vger.kernel.org \
--cc=pabeni@redhat.com \
--cc=pgwipeout@gmail.com \
--cc=robh+dt@kernel.org \
--cc=yanhong.wang@starfivetech.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).