* [PATCH] PCI: qcom: configure the parf halt window size to 1GB
@ 2023-06-23 4:57 Devi Priya
2023-06-23 10:17 ` Konrad Dybcio
2023-06-24 6:23 ` Manivannan Sadhasivam
0 siblings, 2 replies; 6+ messages in thread
From: Devi Priya @ 2023-06-23 4:57 UTC (permalink / raw)
To: agross, andersson, konrad.dybcio, lpieralisi, kw, robh, bhelgaas,
mani, linux-arm-msm, linux-pci, linux-kernel
Cc: quic_srichara, quic_sjaganat, quic_kathirav, quic_anusha, quic_ipkumar
Configure the ADDR_BIT_INDEX of PARF_AXI_MSTR_WR_ADDR_HALT_V2 register with
0x1E to increase the halt window size to 1GB so that, when new inbound
posted write transactions whose address crosses 1G address range, the
controller would halt all the incoming writes until all the previous AXI
responses are received.
Signed-off-by: Devi Priya <quic_devipriy@quicinc.com>
---
This patch depends on the below series which adds support for PCIe
controllers in IPQ9574
https://lore.kernel.org/linux-arm-msm/20230519090219.15925-1-quic_devipriy@quicinc.com/
drivers/pci/controller/dwc/pcie-qcom.c | 9 +++++++++
1 file changed, 9 insertions(+)
diff --git a/drivers/pci/controller/dwc/pcie-qcom.c b/drivers/pci/controller/dwc/pcie-qcom.c
index c7579dfa5b1c..26c40e006120 100644
--- a/drivers/pci/controller/dwc/pcie-qcom.c
+++ b/drivers/pci/controller/dwc/pcie-qcom.c
@@ -116,6 +116,8 @@
/* PARF_AXI_MSTR_WR_ADDR_HALT register fields */
#define EN BIT(31)
+#define ADDR_BIT_INDEX (BIT(0) | BIT(1) | BIT(2) | \
+ BIT(3) | BIT(4) | BIT(5))
/* PARF_LTSSM register fields */
#define LTSSM_EN BIT(8)
@@ -154,6 +156,8 @@
#define QCOM_PCIE_CRC8_POLYNOMIAL (BIT(2) | BIT(1) | BIT(0))
+#define PARF_AXI_MSTR_WR_ADDR_HALT_WINDOW_SIZE 0x1e
+
#define QCOM_PCIE_1_0_0_MAX_CLOCKS 4
struct qcom_pcie_resources_1_0_0 {
struct clk_bulk_data clks[QCOM_PCIE_1_0_0_MAX_CLOCKS];
@@ -1126,6 +1130,11 @@ static int qcom_pcie_post_init(struct qcom_pcie *pcie)
writel(0, pcie->parf + PARF_Q2A_FLUSH);
+ val = readl(pcie->parf + PARF_AXI_MSTR_WR_ADDR_HALT_V2);
+ val &= ~ADDR_BIT_INDEX;
+ writel(val | PARF_AXI_MSTR_WR_ADDR_HALT_WINDOW_SIZE, pcie->parf +
+ PARF_AXI_MSTR_WR_ADDR_HALT_V2);
+
dw_pcie_dbi_ro_wr_en(pci);
writel(PCIE_CAP_SLOT_VAL, pci->dbi_base + offset + PCI_EXP_SLTCAP);
--
2.17.1
^ permalink raw reply related [flat|nested] 6+ messages in thread
* Re: [PATCH] PCI: qcom: configure the parf halt window size to 1GB
2023-06-23 4:57 [PATCH] PCI: qcom: configure the parf halt window size to 1GB Devi Priya
@ 2023-06-23 10:17 ` Konrad Dybcio
2023-07-05 10:25 ` Devi Priya
2023-06-24 6:23 ` Manivannan Sadhasivam
1 sibling, 1 reply; 6+ messages in thread
From: Konrad Dybcio @ 2023-06-23 10:17 UTC (permalink / raw)
To: Devi Priya, agross, andersson, lpieralisi, kw, robh, bhelgaas,
mani, linux-arm-msm, linux-pci, linux-kernel
Cc: quic_srichara, quic_sjaganat, quic_kathirav, quic_anusha, quic_ipkumar
On 23.06.2023 06:57, Devi Priya wrote:
> Configure the ADDR_BIT_INDEX of PARF_AXI_MSTR_WR_ADDR_HALT_V2 register with
> 0x1E to increase the halt window size to 1GB so that, when new inbound
> posted write transactions whose address crosses 1G address range, the
> controller would halt all the incoming writes until all the previous AXI
> responses are received.
>
> Signed-off-by: Devi Priya <quic_devipriy@quicinc.com>
> ---
Has this been tested on anything except IPQ9574? Does it concern other
SoCs?
> This patch depends on the below series which adds support for PCIe
> controllers in IPQ9574
> https://lore.kernel.org/linux-arm-msm/20230519090219.15925-1-quic_devipriy@quicinc.com/
>
> drivers/pci/controller/dwc/pcie-qcom.c | 9 +++++++++
> 1 file changed, 9 insertions(+)
>
> diff --git a/drivers/pci/controller/dwc/pcie-qcom.c b/drivers/pci/controller/dwc/pcie-qcom.c
> index c7579dfa5b1c..26c40e006120 100644
> --- a/drivers/pci/controller/dwc/pcie-qcom.c
> +++ b/drivers/pci/controller/dwc/pcie-qcom.c
> @@ -116,6 +116,8 @@
>
> /* PARF_AXI_MSTR_WR_ADDR_HALT register fields */
> #define EN BIT(31)
> +#define ADDR_BIT_INDEX (BIT(0) | BIT(1) | BIT(2) | \
> + BIT(3) | BIT(4) | BIT(5))
You surely should have the names of these bitfields, mind defining them?
>
> /* PARF_LTSSM register fields */
> #define LTSSM_EN BIT(8)
> @@ -154,6 +156,8 @@
>
> #define QCOM_PCIE_CRC8_POLYNOMIAL (BIT(2) | BIT(1) | BIT(0))
>
> +#define PARF_AXI_MSTR_WR_ADDR_HALT_WINDOW_SIZE 0x1e
> +
> #define QCOM_PCIE_1_0_0_MAX_CLOCKS 4
> struct qcom_pcie_resources_1_0_0 {
> struct clk_bulk_data clks[QCOM_PCIE_1_0_0_MAX_CLOCKS];
> @@ -1126,6 +1130,11 @@ static int qcom_pcie_post_init(struct qcom_pcie *pcie)
>
> writel(0, pcie->parf + PARF_Q2A_FLUSH);
>
> + val = readl(pcie->parf + PARF_AXI_MSTR_WR_ADDR_HALT_V2);
> + val &= ~ADDR_BIT_INDEX;
> + writel(val | PARF_AXI_MSTR_WR_ADDR_HALT_WINDOW_SIZE, pcie->parf +
> + PARF_AXI_MSTR_WR_ADDR_HALT_V2);
val |= ..
writel(val, pcie..)
would be more readable
Konrad
> +
> dw_pcie_dbi_ro_wr_en(pci);
> writel(PCIE_CAP_SLOT_VAL, pci->dbi_base + offset + PCI_EXP_SLTCAP);
>
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH] PCI: qcom: configure the parf halt window size to 1GB
2023-06-23 4:57 [PATCH] PCI: qcom: configure the parf halt window size to 1GB Devi Priya
2023-06-23 10:17 ` Konrad Dybcio
@ 2023-06-24 6:23 ` Manivannan Sadhasivam
2023-07-05 10:27 ` Devi Priya
1 sibling, 1 reply; 6+ messages in thread
From: Manivannan Sadhasivam @ 2023-06-24 6:23 UTC (permalink / raw)
To: Devi Priya
Cc: agross, andersson, konrad.dybcio, lpieralisi, kw, robh, bhelgaas,
linux-arm-msm, linux-pci, linux-kernel, quic_srichara,
quic_sjaganat, quic_kathirav, quic_anusha, quic_ipkumar
On Fri, Jun 23, 2023 at 10:27:31AM +0530, Devi Priya wrote:
> Configure the ADDR_BIT_INDEX of PARF_AXI_MSTR_WR_ADDR_HALT_V2 register with
> 0x1E to increase the halt window size to 1GB so that, when new inbound
> posted write transactions whose address crosses 1G address range, the
> controller would halt all the incoming writes until all the previous AXI
> responses are received.
>
Can you explain how the value of 0x1e corresponds to 1GB window size?
> Signed-off-by: Devi Priya <quic_devipriy@quicinc.com>
> ---
> This patch depends on the below series which adds support for PCIe
> controllers in IPQ9574
> https://lore.kernel.org/linux-arm-msm/20230519090219.15925-1-quic_devipriy@quicinc.com/
>
> drivers/pci/controller/dwc/pcie-qcom.c | 9 +++++++++
> 1 file changed, 9 insertions(+)
>
> diff --git a/drivers/pci/controller/dwc/pcie-qcom.c b/drivers/pci/controller/dwc/pcie-qcom.c
> index c7579dfa5b1c..26c40e006120 100644
> --- a/drivers/pci/controller/dwc/pcie-qcom.c
> +++ b/drivers/pci/controller/dwc/pcie-qcom.c
> @@ -116,6 +116,8 @@
>
> /* PARF_AXI_MSTR_WR_ADDR_HALT register fields */
> #define EN BIT(31)
> +#define ADDR_BIT_INDEX (BIT(0) | BIT(1) | BIT(2) | \
> + BIT(3) | BIT(4) | BIT(5))
GENMASK(5, 0)
>
> /* PARF_LTSSM register fields */
> #define LTSSM_EN BIT(8)
> @@ -154,6 +156,8 @@
>
> #define QCOM_PCIE_CRC8_POLYNOMIAL (BIT(2) | BIT(1) | BIT(0))
>
> +#define PARF_AXI_MSTR_WR_ADDR_HALT_WINDOW_SIZE 0x1e
GENMASK(4, 1) as these are address bits.
- Mani
> +
> #define QCOM_PCIE_1_0_0_MAX_CLOCKS 4
> struct qcom_pcie_resources_1_0_0 {
> struct clk_bulk_data clks[QCOM_PCIE_1_0_0_MAX_CLOCKS];
> @@ -1126,6 +1130,11 @@ static int qcom_pcie_post_init(struct qcom_pcie *pcie)
>
> writel(0, pcie->parf + PARF_Q2A_FLUSH);
>
> + val = readl(pcie->parf + PARF_AXI_MSTR_WR_ADDR_HALT_V2);
> + val &= ~ADDR_BIT_INDEX;
> + writel(val | PARF_AXI_MSTR_WR_ADDR_HALT_WINDOW_SIZE, pcie->parf +
> + PARF_AXI_MSTR_WR_ADDR_HALT_V2);
> +
> dw_pcie_dbi_ro_wr_en(pci);
> writel(PCIE_CAP_SLOT_VAL, pci->dbi_base + offset + PCI_EXP_SLTCAP);
>
> --
> 2.17.1
>
--
மணிவண்ணன் சதாசிவம்
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH] PCI: qcom: configure the parf halt window size to 1GB
2023-06-23 10:17 ` Konrad Dybcio
@ 2023-07-05 10:25 ` Devi Priya
0 siblings, 0 replies; 6+ messages in thread
From: Devi Priya @ 2023-07-05 10:25 UTC (permalink / raw)
To: Konrad Dybcio, agross, andersson, lpieralisi, kw, robh, bhelgaas,
mani, linux-arm-msm, linux-pci, linux-kernel
Cc: quic_srichara, quic_sjaganat, quic_kathirav, quic_anusha, quic_ipkumar
On 6/23/2023 3:47 PM, Konrad Dybcio wrote:
> On 23.06.2023 06:57, Devi Priya wrote:
>> Configure the ADDR_BIT_INDEX of PARF_AXI_MSTR_WR_ADDR_HALT_V2 register with
>> 0x1E to increase the halt window size to 1GB so that, when new inbound
>> posted write transactions whose address crosses 1G address range, the
>> controller would halt all the incoming writes until all the previous AXI
>> responses are received.
>>
>> Signed-off-by: Devi Priya <quic_devipriy@quicinc.com>
>> ---
> Has this been tested on anything except IPQ9574? Does it concern other
> SoCs?
This has been tested on IPQ6018 as well.
>
>
>> This patch depends on the below series which adds support for PCIe
>> controllers in IPQ9574
>> https://lore.kernel.org/linux-arm-msm/20230519090219.15925-1-quic_devipriy@quicinc.com/
>>
>> drivers/pci/controller/dwc/pcie-qcom.c | 9 +++++++++
>> 1 file changed, 9 insertions(+)
>>
>> diff --git a/drivers/pci/controller/dwc/pcie-qcom.c b/drivers/pci/controller/dwc/pcie-qcom.c
>> index c7579dfa5b1c..26c40e006120 100644
>> --- a/drivers/pci/controller/dwc/pcie-qcom.c
>> +++ b/drivers/pci/controller/dwc/pcie-qcom.c
>> @@ -116,6 +116,8 @@
>>
>> /* PARF_AXI_MSTR_WR_ADDR_HALT register fields */
>> #define EN BIT(31)
>> +#define ADDR_BIT_INDEX (BIT(0) | BIT(1) | BIT(2) | \
>> + BIT(3) | BIT(4) | BIT(5))
> You surely should have the names of these bitfields, mind defining them?
Will use GENMASK(5, 0) as suggested by Mani
>
>>
>> /* PARF_LTSSM register fields */
>> #define LTSSM_EN BIT(8)
>> @@ -154,6 +156,8 @@
>>
>> #define QCOM_PCIE_CRC8_POLYNOMIAL (BIT(2) | BIT(1) | BIT(0))
>>
>> +#define PARF_AXI_MSTR_WR_ADDR_HALT_WINDOW_SIZE 0x1e
>> +
>> #define QCOM_PCIE_1_0_0_MAX_CLOCKS 4
>> struct qcom_pcie_resources_1_0_0 {
>> struct clk_bulk_data clks[QCOM_PCIE_1_0_0_MAX_CLOCKS];
>> @@ -1126,6 +1130,11 @@ static int qcom_pcie_post_init(struct qcom_pcie *pcie)
>>
>> writel(0, pcie->parf + PARF_Q2A_FLUSH);
>>
>> + val = readl(pcie->parf + PARF_AXI_MSTR_WR_ADDR_HALT_V2);
>> + val &= ~ADDR_BIT_INDEX;
>> + writel(val | PARF_AXI_MSTR_WR_ADDR_HALT_WINDOW_SIZE, pcie->parf +
>> + PARF_AXI_MSTR_WR_ADDR_HALT_V2);
> val |= ..
> writel(val, pcie..)
>
> would be more readable
Okay
Thanks,
Devi Priya
>
> Konrad
>> +
>> dw_pcie_dbi_ro_wr_en(pci);
>> writel(PCIE_CAP_SLOT_VAL, pci->dbi_base + offset + PCI_EXP_SLTCAP);
>>
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH] PCI: qcom: configure the parf halt window size to 1GB
2023-06-24 6:23 ` Manivannan Sadhasivam
@ 2023-07-05 10:27 ` Devi Priya
2023-07-10 3:22 ` Manivannan Sadhasivam
0 siblings, 1 reply; 6+ messages in thread
From: Devi Priya @ 2023-07-05 10:27 UTC (permalink / raw)
To: Manivannan Sadhasivam
Cc: agross, andersson, konrad.dybcio, lpieralisi, kw, robh, bhelgaas,
linux-arm-msm, linux-pci, linux-kernel, quic_srichara,
quic_sjaganat, quic_kathirav, quic_anusha, quic_ipkumar
On 6/24/2023 11:53 AM, Manivannan Sadhasivam wrote:
> On Fri, Jun 23, 2023 at 10:27:31AM +0530, Devi Priya wrote:
>> Configure the ADDR_BIT_INDEX of PARF_AXI_MSTR_WR_ADDR_HALT_V2 register with
>> 0x1E to increase the halt window size to 1GB so that, when new inbound
>> posted write transactions whose address crosses 1G address range, the
>> controller would halt all the incoming writes until all the previous AXI
>> responses are received.
>>
>
> Can you explain how the value of 0x1e corresponds to 1GB window size?
2^30 (0x1e) = 1G
>
>> Signed-off-by: Devi Priya <quic_devipriy@quicinc.com>
>> ---
>> This patch depends on the below series which adds support for PCIe
>> controllers in IPQ9574
>> https://lore.kernel.org/linux-arm-msm/20230519090219.15925-1-quic_devipriy@quicinc.com/
>>
>> drivers/pci/controller/dwc/pcie-qcom.c | 9 +++++++++
>> 1 file changed, 9 insertions(+)
>>
>> diff --git a/drivers/pci/controller/dwc/pcie-qcom.c b/drivers/pci/controller/dwc/pcie-qcom.c
>> index c7579dfa5b1c..26c40e006120 100644
>> --- a/drivers/pci/controller/dwc/pcie-qcom.c
>> +++ b/drivers/pci/controller/dwc/pcie-qcom.c
>> @@ -116,6 +116,8 @@
>>
>> /* PARF_AXI_MSTR_WR_ADDR_HALT register fields */
>> #define EN BIT(31)
>> +#define ADDR_BIT_INDEX (BIT(0) | BIT(1) | BIT(2) | \
>> + BIT(3) | BIT(4) | BIT(5))
>
> GENMASK(5, 0)
okay
>
>>
>> /* PARF_LTSSM register fields */
>> #define LTSSM_EN BIT(8)
>> @@ -154,6 +156,8 @@
>>
>> #define QCOM_PCIE_CRC8_POLYNOMIAL (BIT(2) | BIT(1) | BIT(0))
>>
>> +#define PARF_AXI_MSTR_WR_ADDR_HALT_WINDOW_SIZE 0x1e
>
> GENMASK(4, 1) as these are address bits.
okay
Thanks,
Devi Priya
>
> - Mani
>
>> +
>> #define QCOM_PCIE_1_0_0_MAX_CLOCKS 4
>> struct qcom_pcie_resources_1_0_0 {
>> struct clk_bulk_data clks[QCOM_PCIE_1_0_0_MAX_CLOCKS];
>> @@ -1126,6 +1130,11 @@ static int qcom_pcie_post_init(struct qcom_pcie *pcie)
>>
>> writel(0, pcie->parf + PARF_Q2A_FLUSH);
>>
>> + val = readl(pcie->parf + PARF_AXI_MSTR_WR_ADDR_HALT_V2);
>> + val &= ~ADDR_BIT_INDEX;
>> + writel(val | PARF_AXI_MSTR_WR_ADDR_HALT_WINDOW_SIZE, pcie->parf +
>> + PARF_AXI_MSTR_WR_ADDR_HALT_V2);
>> +
>> dw_pcie_dbi_ro_wr_en(pci);
>> writel(PCIE_CAP_SLOT_VAL, pci->dbi_base + offset + PCI_EXP_SLTCAP);
>>
>> --
>> 2.17.1
>>
>
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH] PCI: qcom: configure the parf halt window size to 1GB
2023-07-05 10:27 ` Devi Priya
@ 2023-07-10 3:22 ` Manivannan Sadhasivam
0 siblings, 0 replies; 6+ messages in thread
From: Manivannan Sadhasivam @ 2023-07-10 3:22 UTC (permalink / raw)
To: Devi Priya
Cc: Manivannan Sadhasivam, agross, andersson, konrad.dybcio,
lpieralisi, kw, robh, bhelgaas, linux-arm-msm, linux-pci,
linux-kernel, quic_srichara, quic_sjaganat, quic_kathirav,
quic_anusha, quic_ipkumar
On Wed, Jul 05, 2023 at 03:57:13PM +0530, Devi Priya wrote:
>
>
> On 6/24/2023 11:53 AM, Manivannan Sadhasivam wrote:
> > On Fri, Jun 23, 2023 at 10:27:31AM +0530, Devi Priya wrote:
> > > Configure the ADDR_BIT_INDEX of PARF_AXI_MSTR_WR_ADDR_HALT_V2 register with
> > > 0x1E to increase the halt window size to 1GB so that, when new inbound
> > > posted write transactions whose address crosses 1G address range, the
> > > controller would halt all the incoming writes until all the previous AXI
> > > responses are received.
> > >
> >
> > Can you explain how the value of 0x1e corresponds to 1GB window size?
> 2^30 (0x1e) = 1G
> >
So 0x1e selects 2^30 in the hardware? If so, please document it in the commit
message.
- Mani
> > > Signed-off-by: Devi Priya <quic_devipriy@quicinc.com>
> > > ---
> > > This patch depends on the below series which adds support for PCIe
> > > controllers in IPQ9574
> > > https://lore.kernel.org/linux-arm-msm/20230519090219.15925-1-quic_devipriy@quicinc.com/
> > >
> > > drivers/pci/controller/dwc/pcie-qcom.c | 9 +++++++++
> > > 1 file changed, 9 insertions(+)
> > >
> > > diff --git a/drivers/pci/controller/dwc/pcie-qcom.c b/drivers/pci/controller/dwc/pcie-qcom.c
> > > index c7579dfa5b1c..26c40e006120 100644
> > > --- a/drivers/pci/controller/dwc/pcie-qcom.c
> > > +++ b/drivers/pci/controller/dwc/pcie-qcom.c
> > > @@ -116,6 +116,8 @@
> > > /* PARF_AXI_MSTR_WR_ADDR_HALT register fields */
> > > #define EN BIT(31)
> > > +#define ADDR_BIT_INDEX (BIT(0) | BIT(1) | BIT(2) | \
> > > + BIT(3) | BIT(4) | BIT(5))
> >
> > GENMASK(5, 0)
> okay
> >
> > > /* PARF_LTSSM register fields */
> > > #define LTSSM_EN BIT(8)
> > > @@ -154,6 +156,8 @@
> > > #define QCOM_PCIE_CRC8_POLYNOMIAL (BIT(2) | BIT(1) | BIT(0))
> > > +#define PARF_AXI_MSTR_WR_ADDR_HALT_WINDOW_SIZE 0x1e
> >
> > GENMASK(4, 1) as these are address bits.
> okay
>
> Thanks,
> Devi Priya
> >
> > - Mani
> >
> > > +
> > > #define QCOM_PCIE_1_0_0_MAX_CLOCKS 4
> > > struct qcom_pcie_resources_1_0_0 {
> > > struct clk_bulk_data clks[QCOM_PCIE_1_0_0_MAX_CLOCKS];
> > > @@ -1126,6 +1130,11 @@ static int qcom_pcie_post_init(struct qcom_pcie *pcie)
> > > writel(0, pcie->parf + PARF_Q2A_FLUSH);
> > > + val = readl(pcie->parf + PARF_AXI_MSTR_WR_ADDR_HALT_V2);
> > > + val &= ~ADDR_BIT_INDEX;
> > > + writel(val | PARF_AXI_MSTR_WR_ADDR_HALT_WINDOW_SIZE, pcie->parf +
> > > + PARF_AXI_MSTR_WR_ADDR_HALT_V2);
> > > +
> > > dw_pcie_dbi_ro_wr_en(pci);
> > > writel(PCIE_CAP_SLOT_VAL, pci->dbi_base + offset + PCI_EXP_SLTCAP);
> > > --
> > > 2.17.1
> > >
> >
--
மணிவண்ணன் சதாசிவம்
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2023-07-10 3:22 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2023-06-23 4:57 [PATCH] PCI: qcom: configure the parf halt window size to 1GB Devi Priya
2023-06-23 10:17 ` Konrad Dybcio
2023-07-05 10:25 ` Devi Priya
2023-06-24 6:23 ` Manivannan Sadhasivam
2023-07-05 10:27 ` Devi Priya
2023-07-10 3:22 ` Manivannan Sadhasivam
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).