Re: [PATCH net-next v4 6/7] dt-bindings: marvell: Rewrite MV88E6xxx in schema

[Rob Herring <robh@kernel.org>]

On Wed, Oct 18, 2023 at 11:03:45AM +0200, Linus Walleij wrote:
> This is an attempt to rewrite the Marvell MV88E6xxx switch bindings
> in YAML schema.
> 
> The current text binding says:
>   WARNING: This binding is currently unstable. Do not program it into a
>   FLASH never to be changed again. Once this binding is stable, this
>   warning will be removed.
> 
> Well that never happened before we switched to YAML markup,
> we can't have it like this, what about fixing the mess?
> 
> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
> ---
>  .../bindings/net/dsa/marvell,mv88e6xxx.yaml        | 225 +++++++++++++++++++++
>  .../devicetree/bindings/net/dsa/marvell.txt        | 109 ----------
>  MAINTAINERS                                        |   2 +-
>  3 files changed, 226 insertions(+), 110 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/net/dsa/marvell,mv88e6xxx.yaml b/Documentation/devicetree/bindings/net/dsa/marvell,mv88e6xxx.yaml
> new file mode 100644
> index 000000000000..8013ac411b15
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/net/dsa/marvell,mv88e6xxx.yaml
> @@ -0,0 +1,225 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/net/dsa/marvell,mv88e6xxx.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Marvell MV88E6xxx DSA switch family
> +
> +maintainers:
> +  - Andrew Lunn <andrew@lunn.ch>
> +
> +description:
> +  The Marvell MV88E6xxx switch series has been produced and sold
> +  by Marvell since at least 2010. The switch has a few compatibles which
> +  just indicate the base address of the switch, then operating systems
> +  can investigate switch ID registers to find out which actual version
> +  of the switch it is dealing with.
> +
> +properties:
> +  compatible:
> +    enum:
> +      - marvell,mv88e6085
> +      - marvell,mv88e6190
> +      - marvell,mv88e6250
> +    description: |
> +      marvell,mv88e6085: This switch uses base address 0x10.
> +        This switch and its siblings will be autodetected from
> +        ID registers found in the switch, so only "marvell,mv88e6085" should be
> +        specified. This includes the following list of MV88Exxxx switches:
> +        6085, 6095, 6097, 6123, 6131, 6141, 6161, 6165, 6171, 6172, 6175, 6176,
> +        6185, 6240, 6320, 6321, 6341, 6350, 6351, 6352
> +      marvell,mv88e6190: This switch uses base address 0x00.
> +        This switch and its siblings will be autodetected from
> +        ID registers found in the switch, so only "marvell,mv88e6190" should be
> +        specified. This includes the following list of MV88Exxxx switches:
> +        6190, 6190X, 6191, 6290, 6361, 6390, 6390X
> +      marvell,mv88e6250: This switch uses base address 0x08 or 0x18.
> +        This switch and its siblings will be autodetected from
> +        ID registers found in the switch, so only "marvell,mv88e6250" should be
> +        specified. This includes the following list of MV88Exxxx switches:
> +        6220, 6250
> +
> +  reg:
> +    maxItems: 1
> +
> +  eeprom-length:
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    description: Set to the length of an EEPROM connected to the switch. Must be
> +      set if the switch can not detect the presence and/or size of a connected
> +      EEPROM, otherwise optional.
> +
> +  reset-gpios:
> +    description:
> +      GPIO to be used to reset the whole device
> +    maxItems: 1
> +
> +  interrupts:
> +    description: The switch provides an external interrupt line, but it is
> +      not always used by target systems.
> +    maxItems: 1
> +
> +  interrupt-controller:
> +    description: The switch has an internal interrupt controller used by
> +      the different sub-blocks.
> +
> +  '#interrupt-cells':
> +    description: The internal interrupt controller only supports triggering
> +      on active high level interrupts so the second cell must alway be set to
> +      IRQ_TYPE_LEVEL_HIGH.
> +    const: 2
> +
> +  mdio:
> +    $ref: /schemas/net/mdio.yaml#
> +    unevaluatedProperties: false
> +    description: Marvell MV88E6xxx switches have an varying combination of
> +      internal and external MDIO buses, in some cases a combined bus that
> +      can be used both internally and externally. This node is for the
> +      primary bus, used internally and sometimes also externally.
> +
> +  mdio-external:
> +    $ref: /schemas/net/mdio.yaml#
> +    unevaluatedProperties: false
> +    description: Marvell MV88E6xxx switches that have a separate external
> +      MDIO bus use this port to access external components on the MDIO bus.
> +
> +    properties:
> +      compatible:
> +        const: marvell,mv88e6xxx-mdio-external
> +
> +    required:
> +      - compatible
> +
> +$ref: dsa.yaml#

Drop this. Covered by the line below.

> +
> +allOf:
> +  - $ref: dsa.yaml#/$defs/ethernet-ports