* [PATCH v3 0/2] arm64: dts: ti: enable more peripherals
@ 2023-10-19 22:30 Bryan Brattlof
2023-10-19 22:30 ` [PATCH v3 1/2] arm64: dts: ti: k3-am62p: Add nodes for more IPs Bryan Brattlof
2023-10-19 22:30 ` [PATCH v3 2/2] arm64: dts: ti: k3-am62p5-sk: Updates for SK EVM Bryan Brattlof
0 siblings, 2 replies; 3+ messages in thread
From: Bryan Brattlof @ 2023-10-19 22:30 UTC (permalink / raw)
To: Nishanth Menon, Vignesh Raghavendra, Tero Kristo, Rob Herring,
Krzysztof Kozlowski, Conor Dooley
Cc: Linux Kernel Mailing List, ARM Linux Mailing List, Bryan Brattlof
Hello again everyone!
This series enables most of the similar peripherals already enabled for
the am62xxx extended family of TI's K3 devices for the am62p SoC and the
am62p5 start kit board
Thanks for reviewing
~Bryan
Changes from v2: [1]
- removed USB entirely
- removed efuse MAC address region from CPSW
- renamed main_conf from syscon@ to bus@
Changes from v1: [0]
- changed main_conf compatible to simple-bus
- moved all bootph-* properties to bottom of list
- used 0x00 in all reg properties
- changed wkup_conf compatible to simple-mfd
- reserved mcu_esm for MCU firmware use
[0] https://lore.kernel.org/lkml/20231010035903.520635-4-bb@ti.com/
[1] https://lore.kernel.org/lkml/20231018194839.2689377-1-bb@ti.com/
Vignesh Raghavendra (2):
arm64: dts: ti: k3-am62p: Add nodes for more IPs
arm64: dts: ti: k3-am62p5-sk: Updates for SK EVM
arch/arm64/boot/dts/ti/k3-am62p-main.dtsi | 764 ++++++++++++++++++-
arch/arm64/boot/dts/ti/k3-am62p-mcu.dtsi | 190 +++++
arch/arm64/boot/dts/ti/k3-am62p-thermal.dtsi | 47 ++
arch/arm64/boot/dts/ti/k3-am62p-wakeup.dtsi | 69 +-
arch/arm64/boot/dts/ti/k3-am62p.dtsi | 7 +-
arch/arm64/boot/dts/ti/k3-am62p5-sk.dts | 520 ++++++++++++-
6 files changed, 1567 insertions(+), 30 deletions(-)
create mode 100644 arch/arm64/boot/dts/ti/k3-am62p-thermal.dtsi
base-commit: 56bc311585206a8955de793301d4f84fb4ad2ee6
--
2.42.0
^ permalink raw reply [flat|nested] 3+ messages in thread
* [PATCH v3 1/2] arm64: dts: ti: k3-am62p: Add nodes for more IPs
2023-10-19 22:30 [PATCH v3 0/2] arm64: dts: ti: enable more peripherals Bryan Brattlof
@ 2023-10-19 22:30 ` Bryan Brattlof
2023-10-19 22:30 ` [PATCH v3 2/2] arm64: dts: ti: k3-am62p5-sk: Updates for SK EVM Bryan Brattlof
1 sibling, 0 replies; 3+ messages in thread
From: Bryan Brattlof @ 2023-10-19 22:30 UTC (permalink / raw)
To: Nishanth Menon, Vignesh Raghavendra, Tero Kristo, Rob Herring,
Krzysztof Kozlowski, Conor Dooley
Cc: Linux Kernel Mailing List, ARM Linux Mailing List, Bryan Brattlof
From: Vignesh Raghavendra <vigneshr@ti.com>
The am62px shares many of the same IP as the existing am62x family
of SoCs, Introduce more nodes for hardware available on the am62p5.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
---
arch/arm64/boot/dts/ti/k3-am62p-main.dtsi | 764 ++++++++++++++++++-
arch/arm64/boot/dts/ti/k3-am62p-mcu.dtsi | 190 +++++
arch/arm64/boot/dts/ti/k3-am62p-thermal.dtsi | 47 ++
arch/arm64/boot/dts/ti/k3-am62p-wakeup.dtsi | 69 +-
arch/arm64/boot/dts/ti/k3-am62p.dtsi | 7 +-
5 files changed, 1065 insertions(+), 12 deletions(-)
create mode 100644 arch/arm64/boot/dts/ti/k3-am62p-thermal.dtsi
diff --git a/arch/arm64/boot/dts/ti/k3-am62p-main.dtsi b/arch/arm64/boot/dts/ti/k3-am62p-main.dtsi
index fcbfb1b5242b4..963758c7d377a 100644
--- a/arch/arm64/boot/dts/ti/k3-am62p-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am62p-main.dtsi
@@ -40,18 +40,37 @@ gic_its: msi-controller@1820000 {
};
};
+ main_conf: bus@100000 {
+ compatible = "simple-bus";
+ reg = <0x00 0x00100000 0x00 0x20000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x00 0x00 0x00100000 0x20000>;
+
+ phy_gmii_sel: phy@4044 {
+ compatible = "ti,am654-phy-gmii-sel";
+ reg = <0x4044 0x8>;
+ #phy-cells = <1>;
+ };
+
+ epwm_tbclk: clock-controller@4130 {
+ compatible = "ti,am62-epwm-tbclk";
+ reg = <0x4130 0x4>;
+ #clock-cells = <1>;
+ };
+ };
+
dmss: bus@48000000 {
- bootph-all;
compatible = "simple-bus";
#address-cells = <2>;
#size-cells = <2>;
dma-ranges;
ranges = <0x00 0x48000000 0x00 0x48000000 0x00 0x06400000>;
+ bootph-all;
ti,sci-dev-id = <25>;
secure_proxy_main: mailbox@4d000000 {
- bootph-all;
compatible = "ti,am654-secure-proxy";
#mbox-cells = <1>;
reg-names = "target_data", "rt", "scfg";
@@ -60,11 +79,76 @@ secure_proxy_main: mailbox@4d000000 {
<0x00 0x4a400000 0x00 0x80000>;
interrupt-names = "rx_012";
interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+ bootph-all;
+ };
+
+ inta_main_dmss: interrupt-controller@48000000 {
+ compatible = "ti,sci-inta";
+ reg = <0x00 0x48000000 0x00 0x100000>;
+ #interrupt-cells = <0>;
+ interrupt-controller;
+ interrupt-parent = <&gic500>;
+ msi-controller;
+ ti,sci = <&dmsc>;
+ ti,sci-dev-id = <28>;
+ ti,interrupt-ranges = <5 69 35>;
+ ti,unmapped-event-sources = <&main_bcdma>, <&main_pktdma>;
+ };
+
+ main_bcdma: dma-controller@485c0100 {
+ compatible = "ti,am64-dmss-bcdma";
+ reg = <0x00 0x485c0100 0x00 0x100>,
+ <0x00 0x4c000000 0x00 0x20000>,
+ <0x00 0x4a820000 0x00 0x20000>,
+ <0x00 0x4aa40000 0x00 0x20000>,
+ <0x00 0x4bc00000 0x00 0x100000>;
+ reg-names = "gcfg", "bchanrt", "rchanrt", "tchanrt", "ringrt";
+ msi-parent = <&inta_main_dmss>;
+ #dma-cells = <3>;
+
+ ti,sci = <&dmsc>;
+ ti,sci-dev-id = <26>;
+ ti,sci-rm-range-bchan = <0x20>; /* BLOCK_COPY_CHAN */
+ ti,sci-rm-range-rchan = <0x21>; /* SPLIT_TR_RX_CHAN */
+ ti,sci-rm-range-tchan = <0x22>; /* SPLIT_TR_TX_CHAN */
+ bootph-all;
+ };
+
+ main_pktdma: dma-controller@485c0000 {
+ compatible = "ti,am64-dmss-pktdma";
+ reg = <0x00 0x485c0000 0x00 0x100>,
+ <0x00 0x4a800000 0x00 0x20000>,
+ <0x00 0x4aa00000 0x00 0x40000>,
+ <0x00 0x4b800000 0x00 0x400000>;
+ reg-names = "gcfg", "rchanrt", "tchanrt", "ringrt";
+ msi-parent = <&inta_main_dmss>;
+ #dma-cells = <2>;
+ bootph-all;
+
+ ti,sci = <&dmsc>;
+ ti,sci-dev-id = <30>;
+ ti,sci-rm-range-tchan = <0x23>, /* UNMAPPED_TX_CHAN */
+ <0x24>, /* CPSW_TX_CHAN */
+ <0x25>, /* SAUL_TX_0_CHAN */
+ <0x26>; /* SAUL_TX_1_CHAN */
+ ti,sci-rm-range-tflow = <0x10>, /* RING_UNMAPPED_TX_CHAN */
+ <0x11>, /* RING_CPSW_TX_CHAN */
+ <0x12>, /* RING_SAUL_TX_0_CHAN */
+ <0x13>; /* RING_SAUL_TX_1_CHAN */
+ ti,sci-rm-range-rchan = <0x29>, /* UNMAPPED_RX_CHAN */
+ <0x2b>, /* CPSW_RX_CHAN */
+ <0x2d>, /* SAUL_RX_0_CHAN */
+ <0x2f>, /* SAUL_RX_1_CHAN */
+ <0x31>, /* SAUL_RX_2_CHAN */
+ <0x33>; /* SAUL_RX_3_CHAN */
+ ti,sci-rm-range-rflow = <0x2a>, /* FLOW_UNMAPPED_RX_CHAN */
+ <0x2c>, /* FLOW_CPSW_RX_CHAN */
+ <0x2e>, /* FLOW_SAUL_RX_0/1_CHAN */
+ <0x32>; /* FLOW_SAUL_RX_2/3_CHAN */
};
};
dmsc: system-controller@44043000 {
- bootph-all;
compatible = "ti,k2g-sci";
ti,host-id = <12>;
mbox-names = "rx", "tx";
@@ -72,37 +156,72 @@ dmsc: system-controller@44043000 {
<&secure_proxy_main 13>;
reg-names = "debug_messages";
reg = <0x00 0x44043000 0x00 0xfe0>;
+ bootph-all;
k3_pds: power-controller {
- bootph-all;
compatible = "ti,sci-pm-domain";
#power-domain-cells = <2>;
+ bootph-all;
};
k3_clks: clock-controller {
- bootph-all;
compatible = "ti,k2g-sci-clk";
#clock-cells = <2>;
+ bootph-all;
};
k3_reset: reset-controller {
- bootph-all;
compatible = "ti,sci-reset";
#reset-cells = <2>;
+ bootph-all;
};
};
- main_pmx0: pinctrl@f4000 {
+ crypto: crypto@40900000 {
+ compatible = "ti,am62-sa3ul";
+ reg = <0x00 0x40900000 0x00 0x1200>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges = <0x00 0x40900000 0x00 0x40900000 0x00 0x30000>;
+
+ dmas = <&main_pktdma 0xf501 0>, <&main_pktdma 0x7506 0>,
+ <&main_pktdma 0x7507 0>;
+ dma-names = "tx", "rx1", "rx2";
+ };
+
+ secure_proxy_sa3: mailbox@43600000 {
+ compatible = "ti,am654-secure-proxy";
+ #mbox-cells = <1>;
+ reg-names = "target_data", "rt", "scfg";
+ reg = <0x00 0x43600000 0x00 0x10000>,
+ <0x00 0x44880000 0x00 0x20000>,
+ <0x00 0x44860000 0x00 0x20000>;
+ /*
+ * Marked Disabled:
+ * Node is incomplete as it is meant for bootloaders and
+ * firmware on non-MPU processors
+ */
+ status = "disabled";
bootph-all;
+ };
+
+ main_pmx0: pinctrl@f4000 {
compatible = "pinctrl-single";
reg = <0x00 0xf4000 0x00 0x2ac>;
#pinctrl-cells = <1>;
pinctrl-single,register-width = <32>;
pinctrl-single,function-mask = <0xffffffff>;
+ bootph-all;
+ };
+
+ main_esm: esm@420000 {
+ compatible = "ti,j721e-esm";
+ reg = <0x00 0x420000 0x00 0x1000>;
+ ti,esm-pins = <160>, <161>, <162>, <163>, <177>, <178>;
+ bootph-pre-ram;
};
main_timer0: timer@2400000 {
- bootph-all;
compatible = "ti,am654-timer";
reg = <0x00 0x2400000 0x00 0x400>;
interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
@@ -112,6 +231,91 @@ main_timer0: timer@2400000 {
assigned-clock-parents = <&k3_clks 36 3>;
power-domains = <&k3_pds 36 TI_SCI_PD_EXCLUSIVE>;
ti,timer-pwm;
+ bootph-all;
+ };
+
+ main_timer1: timer@2410000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x2410000 0x00 0x400>;
+ interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 37 2>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 37 2>;
+ assigned-clock-parents = <&k3_clks 37 3>;
+ power-domains = <&k3_pds 37 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ main_timer2: timer@2420000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x2420000 0x00 0x400>;
+ interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 38 2>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 38 2>;
+ assigned-clock-parents = <&k3_clks 38 3>;
+ power-domains = <&k3_pds 38 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ main_timer3: timer@2430000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x2430000 0x00 0x400>;
+ interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 39 2>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 39 2>;
+ assigned-clock-parents = <&k3_clks 39 3>;
+ power-domains = <&k3_pds 39 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ main_timer4: timer@2440000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x2440000 0x00 0x400>;
+ interrupts = <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 40 2>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 40 2>;
+ assigned-clock-parents = <&k3_clks 40 3>;
+ power-domains = <&k3_pds 40 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ main_timer5: timer@2450000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x2450000 0x00 0x400>;
+ interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 41 2>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 41 2>;
+ assigned-clock-parents = <&k3_clks 41 3>;
+ power-domains = <&k3_pds 41 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ main_timer6: timer@2460000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x2460000 0x00 0x400>;
+ interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 42 2>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 42 2>;
+ assigned-clock-parents = <&k3_clks 42 3>;
+ power-domains = <&k3_pds 42 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ main_timer7: timer@2470000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x2470000 0x00 0x400>;
+ interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 43 2>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 43 2>;
+ assigned-clock-parents = <&k3_clks 43 3>;
+ power-domains = <&k3_pds 43 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
};
main_uart0: serial@2800000 {
@@ -133,4 +337,548 @@ main_uart1: serial@2810000 {
clock-names = "fclk";
status = "disabled";
};
+
+ main_uart2: serial@2820000 {
+ compatible = "ti,am64-uart", "ti,am654-uart";
+ reg = <0x00 0x02820000 0x00 0x100>;
+ interrupts = <GIC_SPI 180 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&k3_pds 153 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 153 0>;
+ clock-names = "fclk";
+ status = "disabled";
+ };
+
+ main_uart3: serial@2830000 {
+ compatible = "ti,am64-uart", "ti,am654-uart";
+ reg = <0x00 0x02830000 0x00 0x100>;
+ interrupts = <GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&k3_pds 154 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 154 0>;
+ clock-names = "fclk";
+ status = "disabled";
+ };
+
+ main_uart4: serial@2840000 {
+ compatible = "ti,am64-uart", "ti,am654-uart";
+ reg = <0x00 0x02840000 0x00 0x100>;
+ interrupts = <GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&k3_pds 155 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 155 0>;
+ clock-names = "fclk";
+ status = "disabled";
+ };
+
+ main_uart5: serial@2850000 {
+ compatible = "ti,am64-uart", "ti,am654-uart";
+ reg = <0x00 0x02850000 0x00 0x100>;
+ interrupts = <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&k3_pds 156 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 156 0>;
+ clock-names = "fclk";
+ status = "disabled";
+ };
+
+ main_uart6: serial@2860000 {
+ compatible = "ti,am64-uart", "ti,am654-uart";
+ reg = <0x00 0x02860000 0x00 0x100>;
+ interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&k3_pds 158 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 158 0>;
+ clock-names = "fclk";
+ status = "disabled";
+ };
+
+ main_i2c0: i2c@20000000 {
+ compatible = "ti,am64-i2c", "ti,omap4-i2c";
+ reg = <0x00 0x20000000 0x00 0x100>;
+ interrupts = <GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&k3_pds 102 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 102 2>;
+ clock-names = "fck";
+ status = "disabled";
+ };
+
+ main_i2c1: i2c@20010000 {
+ compatible = "ti,am64-i2c", "ti,omap4-i2c";
+ reg = <0x00 0x20010000 0x00 0x100>;
+ interrupts = <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&k3_pds 103 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 103 2>;
+ clock-names = "fck";
+ status = "disabled";
+ };
+
+ main_i2c2: i2c@20020000 {
+ compatible = "ti,am64-i2c", "ti,omap4-i2c";
+ reg = <0x00 0x20020000 0x00 0x100>;
+ interrupts = <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&k3_pds 104 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 104 2>;
+ clock-names = "fck";
+ status = "disabled";
+ };
+
+ main_i2c3: i2c@20030000 {
+ compatible = "ti,am64-i2c", "ti,omap4-i2c";
+ reg = <0x00 0x20030000 0x00 0x100>;
+ interrupts = <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&k3_pds 105 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 105 2>;
+ clock-names = "fck";
+ status = "disabled";
+ };
+
+ main_spi0: spi@20100000 {
+ compatible = "ti,am654-mcspi", "ti,omap4-mcspi";
+ reg = <0x00 0x20100000 0x00 0x400>;
+ interrupts = <GIC_SPI 172 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&k3_pds 141 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 141 0>;
+ status = "disabled";
+ };
+
+ main_spi1: spi@20110000 {
+ compatible = "ti,am654-mcspi","ti,omap4-mcspi";
+ reg = <0x00 0x20110000 0x00 0x400>;
+ interrupts = <GIC_SPI 173 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&k3_pds 142 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 142 0>;
+ status = "disabled";
+ };
+
+ main_spi2: spi@20120000 {
+ compatible = "ti,am654-mcspi","ti,omap4-mcspi";
+ reg = <0x00 0x20120000 0x00 0x400>;
+ interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&k3_pds 143 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 143 0>;
+ status = "disabled";
+ };
+
+ main_gpio_intr: interrupt-controller@a00000 {
+ compatible = "ti,sci-intr";
+ reg = <0x00 0x00a00000 0x00 0x800>;
+ ti,intr-trigger-type = <1>;
+ interrupt-controller;
+ interrupt-parent = <&gic500>;
+ #interrupt-cells = <1>;
+ ti,sci = <&dmsc>;
+ ti,sci-dev-id = <3>;
+ ti,interrupt-ranges = <0 32 16>;
+ };
+
+ main_gpio0: gpio@600000 {
+ compatible = "ti,am64-gpio", "ti,keystone-gpio";
+ reg = <0x00 0x00600000 0x00 0x100>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-parent = <&main_gpio_intr>;
+ interrupts = <190>, <191>, <192>,
+ <193>, <194>, <195>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ ti,ngpio = <92>;
+ ti,davinci-gpio-unbanked = <0>;
+ power-domains = <&k3_pds 77 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 77 0>;
+ clock-names = "gpio";
+ };
+
+ main_gpio1: gpio@601000 {
+ compatible = "ti,am64-gpio", "ti,keystone-gpio";
+ reg = <0x00 0x00601000 0x00 0x100>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-parent = <&main_gpio_intr>;
+ interrupts = <180>, <181>, <182>,
+ <183>, <184>, <185>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ ti,ngpio = <52>;
+ ti,davinci-gpio-unbanked = <0>;
+ power-domains = <&k3_pds 78 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 78 0>;
+ clock-names = "gpio";
+ };
+
+ sdhci0: mmc@fa10000 {
+ compatible = "ti,am64-sdhci-8bit";
+ reg = <0x00 0x0fa10000 0x00 0x1000>, <0x00 0x0fa18000 0x00 0x400>;
+ interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&k3_pds 57 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 57 1>, <&k3_clks 57 2>;
+ clock-names = "clk_ahb", "clk_xin";
+ assigned-clocks = <&k3_clks 57 2>;
+ assigned-clock-parents = <&k3_clks 57 4>;
+ ti,otap-del-sel-legacy = <0x0>;
+ status = "disabled";
+ };
+
+ sdhci1: mmc@fa00000 {
+ compatible = "ti,am62-sdhci";
+ reg = <0x00 0x0fa00000 0x00 0x1000>, <0x00 0x0fa08000 0x00 0x400>;
+ interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&k3_pds 58 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 58 5>, <&k3_clks 58 6>;
+ clock-names = "clk_ahb", "clk_xin";
+ ti,otap-del-sel-legacy = <0x8>;
+ status = "disabled";
+ };
+
+ sdhci2: mmc@fa20000 {
+ compatible = "ti,am62-sdhci";
+ reg = <0x00 0x0fa20000 0x00 0x1000>, <0x00 0x0fa28000 0x00 0x400>;
+ interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&k3_pds 184 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 184 5>, <&k3_clks 184 6>;
+ clock-names = "clk_ahb", "clk_xin";
+ ti,otap-del-sel-legacy = <0x8>;
+ status = "disabled";
+ };
+
+ fss: bus@fc00000 {
+ compatible = "simple-bus";
+ reg = <0x00 0x0fc00000 0x00 0x70000>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ ospi0: spi@fc40000 {
+ compatible = "ti,am654-ospi", "cdns,qspi-nor";
+ reg = <0x00 0x0fc40000 0x00 0x100>,
+ <0x05 0x00000000 0x01 0x00000000>;
+ interrupts = <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>;
+ cdns,fifo-depth = <256>;
+ cdns,fifo-width = <4>;
+ cdns,trigger-address = <0x0>;
+ clocks = <&k3_clks 75 7>;
+ assigned-clocks = <&k3_clks 75 7>;
+ assigned-clock-parents = <&k3_clks 75 8>;
+ assigned-clock-rates = <166666666>;
+ power-domains = <&k3_pds 75 TI_SCI_PD_EXCLUSIVE>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+ };
+
+ cpsw3g: ethernet@8000000 {
+ compatible = "ti,am642-cpsw-nuss";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ reg = <0x00 0x08000000 0x00 0x200000>;
+ reg-names = "cpsw_nuss";
+ ranges = <0x00 0x00 0x00 0x08000000 0x00 0x200000>;
+ clocks = <&k3_clks 13 0>;
+ assigned-clocks = <&k3_clks 13 3>;
+ assigned-clock-parents = <&k3_clks 13 11>;
+ clock-names = "fck";
+ power-domains = <&k3_pds 13 TI_SCI_PD_EXCLUSIVE>;
+
+ dmas = <&main_pktdma 0xc600 15>,
+ <&main_pktdma 0xc601 15>,
+ <&main_pktdma 0xc602 15>,
+ <&main_pktdma 0xc603 15>,
+ <&main_pktdma 0xc604 15>,
+ <&main_pktdma 0xc605 15>,
+ <&main_pktdma 0xc606 15>,
+ <&main_pktdma 0xc607 15>,
+ <&main_pktdma 0x4600 15>;
+ dma-names = "tx0", "tx1", "tx2", "tx3", "tx4", "tx5", "tx6",
+ "tx7", "rx";
+
+ ethernet-ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpsw_port1: port@1 {
+ reg = <1>;
+ ti,mac-only;
+ label = "port1";
+ phys = <&phy_gmii_sel 1>;
+ mac-address = [00 00 00 00 00 00];
+ };
+
+ cpsw_port2: port@2 {
+ reg = <2>;
+ ti,mac-only;
+ label = "port2";
+ phys = <&phy_gmii_sel 2>;
+ mac-address = [00 00 00 00 00 00];
+ };
+ };
+
+ cpsw3g_mdio: mdio@f00 {
+ compatible = "ti,cpsw-mdio","ti,davinci_mdio";
+ reg = <0x00 0xf00 0x00 0x100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&k3_clks 13 0>;
+ clock-names = "fck";
+ bus_freq = <1000000>;
+ status = "disabled";
+ };
+
+ cpts@3d000 {
+ compatible = "ti,j721e-cpts";
+ reg = <0x00 0x3d000 0x00 0x400>;
+ clocks = <&k3_clks 13 3>;
+ clock-names = "cpts";
+ interrupts-extended = <&gic500 GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "cpts";
+ ti,cpts-ext-ts-inputs = <4>;
+ ti,cpts-periodic-outputs = <2>;
+ };
+ };
+
+ hwspinlock: spinlock@2a000000 {
+ compatible = "ti,am64-hwspinlock";
+ reg = <0x00 0x2a000000 0x00 0x1000>;
+ #hwlock-cells = <1>;
+ };
+
+ mailbox0_cluster0: mailbox@29000000 {
+ compatible = "ti,am64-mailbox";
+ reg = <0x00 0x29000000 0x00 0x200>;
+ interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
+ #mbox-cells = <1>;
+ ti,mbox-num-users = <4>;
+ ti,mbox-num-fifos = <16>;
+ };
+
+ mailbox0_cluster1: mailbox@29010000 {
+ compatible = "ti,am64-mailbox";
+ reg = <0x00 0x29010000 0x00 0x200>;
+ interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
+ #mbox-cells = <1>;
+ ti,mbox-num-users = <4>;
+ ti,mbox-num-fifos = <16>;
+ };
+
+ mailbox0_cluster2: mailbox@29020000 {
+ compatible = "ti,am64-mailbox";
+ reg = <0x00 0x29020000 0x00 0x200>;
+ interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
+ #mbox-cells = <1>;
+ ti,mbox-num-users = <4>;
+ ti,mbox-num-fifos = <16>;
+ };
+
+ mailbox0_cluster3: mailbox@29030000 {
+ compatible = "ti,am64-mailbox";
+ reg = <0x00 0x29030000 0x00 0x200>;
+ interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
+ #mbox-cells = <1>;
+ ti,mbox-num-users = <4>;
+ ti,mbox-num-fifos = <16>;
+ };
+
+ ecap0: pwm@23100000 {
+ compatible = "ti,am3352-ecap";
+ #pwm-cells = <3>;
+ reg = <0x00 0x23100000 0x00 0x100>;
+ power-domains = <&k3_pds 51 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 51 0>;
+ clock-names = "fck";
+ status = "disabled";
+ };
+
+ ecap1: pwm@23110000 {
+ compatible = "ti,am3352-ecap";
+ #pwm-cells = <3>;
+ reg = <0x00 0x23110000 0x00 0x100>;
+ power-domains = <&k3_pds 52 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 52 0>;
+ clock-names = "fck";
+ status = "disabled";
+ };
+
+ ecap2: pwm@23120000 {
+ compatible = "ti,am3352-ecap";
+ #pwm-cells = <3>;
+ reg = <0x00 0x23120000 0x00 0x100>;
+ power-domains = <&k3_pds 53 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 53 0>;
+ clock-names = "fck";
+ status = "disabled";
+ };
+
+ main_mcan0: can@20701000 {
+ compatible = "bosch,m_can";
+ reg = <0x00 0x20701000 0x00 0x200>,
+ <0x00 0x20708000 0x00 0x8000>;
+ reg-names = "m_can", "message_ram";
+ power-domains = <&k3_pds 98 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 98 6>, <&k3_clks 98 1>;
+ clock-names = "hclk", "cclk";
+ interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "int0", "int1";
+ bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+ status = "disabled";
+ };
+
+ main_mcan1: can@20711000 {
+ compatible = "bosch,m_can";
+ reg = <0x00 0x20711000 0x00 0x200>,
+ <0x00 0x20718000 0x00 0x8000>;
+ reg-names = "m_can", "message_ram";
+ power-domains = <&k3_pds 99 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 99 6>, <&k3_clks 99 1>;
+ clock-names = "hclk", "cclk";
+ interrupts = <GIC_SPI 213 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 214 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "int0", "int1";
+ bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+ status = "disabled";
+ };
+
+ main_rti0: watchdog@e000000 {
+ compatible = "ti,j7-rti-wdt";
+ reg = <0x00 0x0e000000 0x00 0x100>;
+ clocks = <&k3_clks 125 0>;
+ power-domains = <&k3_pds 125 TI_SCI_PD_EXCLUSIVE>;
+ assigned-clocks = <&k3_clks 125 0>;
+ assigned-clock-parents = <&k3_clks 125 2>;
+ };
+
+ main_rti1: watchdog@e010000 {
+ compatible = "ti,j7-rti-wdt";
+ reg = <0x00 0x0e010000 0x00 0x100>;
+ clocks = <&k3_clks 126 0>;
+ power-domains = <&k3_pds 126 TI_SCI_PD_EXCLUSIVE>;
+ assigned-clocks = <&k3_clks 126 0>;
+ assigned-clock-parents = <&k3_clks 126 2>;
+ };
+
+ main_rti2: watchdog@e020000 {
+ compatible = "ti,j7-rti-wdt";
+ reg = <0x00 0x0e020000 0x00 0x100>;
+ clocks = <&k3_clks 127 0>;
+ power-domains = <&k3_pds 127 TI_SCI_PD_EXCLUSIVE>;
+ assigned-clocks = <&k3_clks 127 0>;
+ assigned-clock-parents = <&k3_clks 127 2>;
+ };
+
+ main_rti3: watchdog@e030000 {
+ compatible = "ti,j7-rti-wdt";
+ reg = <0x00 0x0e030000 0x00 0x100>;
+ clocks = <&k3_clks 128 0>;
+ power-domains = <&k3_pds 128 TI_SCI_PD_EXCLUSIVE>;
+ assigned-clocks = <&k3_clks 128 0>;
+ assigned-clock-parents = <&k3_clks 128 2>;
+ };
+
+ main_rti15: watchdog@e0f0000 {
+ compatible = "ti,j7-rti-wdt";
+ reg = <0x00 0x0e0f0000 0x00 0x100>;
+ clocks = <&k3_clks 130 0>;
+ power-domains = <&k3_pds 130 TI_SCI_PD_EXCLUSIVE>;
+ assigned-clocks = <&k3_clks 130 0>;
+ assigned-clock-parents = <&k3_clks 130 2>;
+ };
+
+ epwm0: pwm@23000000 {
+ compatible = "ti,am64-epwm", "ti,am3352-ehrpwm";
+ #pwm-cells = <3>;
+ reg = <0x00 0x23000000 0x00 0x100>;
+ power-domains = <&k3_pds 86 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&epwm_tbclk 0>, <&k3_clks 86 0>;
+ clock-names = "tbclk", "fck";
+ status = "disabled";
+ };
+
+ epwm1: pwm@23010000 {
+ compatible = "ti,am64-epwm", "ti,am3352-ehrpwm";
+ #pwm-cells = <3>;
+ reg = <0x00 0x23010000 0x00 0x100>;
+ power-domains = <&k3_pds 87 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&epwm_tbclk 1>, <&k3_clks 87 0>;
+ clock-names = "tbclk", "fck";
+ status = "disabled";
+ };
+
+ epwm2: pwm@23020000 {
+ compatible = "ti,am64-epwm", "ti,am3352-ehrpwm";
+ #pwm-cells = <3>;
+ reg = <0x00 0x23020000 0x00 0x100>;
+ power-domains = <&k3_pds 88 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&epwm_tbclk 2>, <&k3_clks 88 0>;
+ clock-names = "tbclk", "fck";
+ status = "disabled";
+ };
+
+ mcasp0: audio-controller@2b00000 {
+ compatible = "ti,am33xx-mcasp-audio";
+ reg = <0x00 0x02b00000 0x00 0x2000>,
+ <0x00 0x02b08000 0x00 0x400>;
+ reg-names = "mpu", "dat";
+ interrupts = <GIC_SPI 236 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 235 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "tx", "rx";
+
+ dmas = <&main_bcdma 0 0xc500 0>, <&main_bcdma 0 0x4500 0>;
+ dma-names = "tx", "rx";
+
+ clocks = <&k3_clks 190 0>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 190 0>;
+ assigned-clock-parents = <&k3_clks 190 2>;
+ power-domains = <&k3_pds 190 TI_SCI_PD_EXCLUSIVE>;
+ status = "disabled";
+ };
+
+ mcasp1: audio-controller@2b10000 {
+ compatible = "ti,am33xx-mcasp-audio";
+ reg = <0x00 0x02b10000 0x00 0x2000>,
+ <0x00 0x02b18000 0x00 0x400>;
+ reg-names = "mpu", "dat";
+ interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 237 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "tx", "rx";
+
+ dmas = <&main_bcdma 0 0xc501 0>, <&main_bcdma 0 0x4501 0>;
+ dma-names = "tx", "rx";
+
+ clocks = <&k3_clks 191 0>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 191 0>;
+ assigned-clock-parents = <&k3_clks 191 2>;
+ power-domains = <&k3_pds 191 TI_SCI_PD_EXCLUSIVE>;
+ status = "disabled";
+ };
+
+ mcasp2: audio-controller@2b20000 {
+ compatible = "ti,am33xx-mcasp-audio";
+ reg = <0x00 0x02b20000 0x00 0x2000>,
+ <0x00 0x02b28000 0x00 0x400>;
+ reg-names = "mpu", "dat";
+ interrupts = <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 239 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "tx", "rx";
+
+ dmas = <&main_bcdma 0 0xc502 0>, <&main_bcdma 0 0x4502 0>;
+ dma-names = "tx", "rx";
+
+ clocks = <&k3_clks 192 0>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 192 0>;
+ assigned-clock-parents = <&k3_clks 192 2>;
+ power-domains = <&k3_pds 192 TI_SCI_PD_EXCLUSIVE>;
+ status = "disabled";
+ };
};
diff --git a/arch/arm64/boot/dts/ti/k3-am62p-mcu.dtsi b/arch/arm64/boot/dts/ti/k3-am62p-mcu.dtsi
index 27ca1c9c6d135..c4b0b91d70cf3 100644
--- a/arch/arm64/boot/dts/ti/k3-am62p-mcu.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am62p-mcu.dtsi
@@ -11,5 +11,195 @@ mcu_pmx0: pinctrl@4084000 {
#pinctrl-cells = <1>;
pinctrl-single,register-width = <32>;
pinctrl-single,function-mask = <0xffffffff>;
+ bootph-all;
+ };
+
+ mcu_esm: esm@4100000 {
+ compatible = "ti,j721e-esm";
+ reg = <0x00 0x4100000 0x00 0x1000>;
+ ti,esm-pins = <0>, <1>, <2>, <85>;
+ status = "reserved";
+ bootph-pre-ram;
+ };
+
+ /*
+ * The MCU domain timer interrupts are routed only to the ESM module,
+ * and not currently available for Linux. The MCU domain timers are
+ * of limited use without interrupts, and likely reserved by the ESM.
+ */
+ mcu_timer0: timer@4800000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x4800000 0x00 0x400>;
+ clocks = <&k3_clks 35 2>;
+ clock-names = "fck";
+ power-domains = <&k3_pds 35 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ status = "reserved";
+ };
+
+ mcu_timer1: timer@4810000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x4810000 0x00 0x400>;
+ clocks = <&k3_clks 48 2>;
+ clock-names = "fck";
+ power-domains = <&k3_pds 48 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ status = "reserved";
+ };
+
+ mcu_timer2: timer@4820000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x4820000 0x00 0x400>;
+ clocks = <&k3_clks 49 2>;
+ clock-names = "fck";
+ power-domains = <&k3_pds 49 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ status = "reserved";
+ };
+
+ mcu_timer3: timer@4830000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x4830000 0x00 0x400>;
+ clocks = <&k3_clks 50 2>;
+ clock-names = "fck";
+ power-domains = <&k3_pds 50 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ status = "reserved";
+ };
+
+ mcu_uart0: serial@4a00000 {
+ compatible = "ti,am64-uart", "ti,am654-uart";
+ reg = <0x00 0x04a00000 0x00 0x100>;
+ interrupts = <GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&k3_pds 149 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 149 0>;
+ clock-names = "fclk";
+ status = "disabled";
+ };
+
+ mcu_i2c0: i2c@4900000 {
+ compatible = "ti,am64-i2c", "ti,omap4-i2c";
+ reg = <0x00 0x04900000 0x00 0x100>;
+ interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&k3_pds 106 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 106 2>;
+ clock-names = "fck";
+ status = "disabled";
+ };
+
+ mcu_spi0: spi@4b00000 {
+ compatible = "ti,am654-mcspi", "ti,omap4-mcspi";
+ reg = <0x00 0x04b00000 0x00 0x400>;
+ interrupts = <GIC_SPI 176 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&k3_pds 147 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 147 0>;
+ status = "disabled";
+ };
+
+ mcu_spi1: spi@4b10000 {
+ compatible = "ti,am654-mcspi","ti,omap4-mcspi";
+ reg = <0x00 0x04b10000 0x00 0x400>;
+ interrupts = <GIC_SPI 177 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&k3_pds 148 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 148 0>;
+ status = "disabled";
+ };
+
+ mcu_gpio_intr: interrupt-controller@4210000 {
+ compatible = "ti,sci-intr";
+ reg = <0x00 0x04210000 0x00 0x200>;
+ ti,intr-trigger-type = <1>;
+ interrupt-controller;
+ interrupt-parent = <&gic500>;
+ #interrupt-cells = <1>;
+ ti,sci = <&dmsc>;
+ ti,sci-dev-id = <5>;
+ ti,interrupt-ranges = <0 104 4>;
+ };
+
+ mcu_gpio0: gpio@4201000 {
+ compatible = "ti,am64-gpio", "ti,keystone-gpio";
+ reg = <0x00 0x4201000 0x00 0x100>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-parent = <&mcu_gpio_intr>;
+ interrupts = <30>, <31>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ ti,ngpio = <24>;
+ ti,davinci-gpio-unbanked = <0>;
+ power-domains = <&k3_pds 79 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 79 0>;
+ clock-names = "gpio";
+ };
+
+ mcu_rti0: watchdog@4880000 {
+ compatible = "ti,j7-rti-wdt";
+ reg = <0x00 0x04880000 0x00 0x100>;
+ clocks = <&k3_clks 131 0>;
+ power-domains = <&k3_pds 131 TI_SCI_PD_EXCLUSIVE>;
+ assigned-clocks = <&k3_clks 131 0>;
+ assigned-clock-parents = <&k3_clks 131 2>;
+ /* Tightly coupled to M4F */
+ status = "reserved";
+ };
+
+ mcu_mcan0: can@4e08000 {
+ compatible = "bosch,m_can";
+ reg = <0x00 0x4e08000 0x00 0x200>,
+ <0x00 0x4e00000 0x00 0x8000>;
+ reg-names = "m_can", "message_ram";
+ power-domains = <&k3_pds 188 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 188 6>, <&k3_clks 188 1>;
+ clock-names = "hclk", "cclk";
+ bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+ interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "int0", "int1";
+ status = "disabled";
+ };
+
+ mcu_mcan1: can@4e18000 {
+ compatible = "bosch,m_can";
+ reg = <0x00 0x4e18000 0x00 0x200>,
+ <0x00 0x4e10000 0x00 0x8000>;
+ reg-names = "m_can", "message_ram";
+ power-domains = <&k3_pds 189 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 189 6>, <&k3_clks 189 1>;
+ clock-names = "hclk", "cclk";
+ bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+ interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "int0", "int1";
+ status = "disabled";
+ };
+
+ mcu_r5fss0: r5fss@79000000 {
+ compatible = "ti,am62-r5fss";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x79000000 0x00 0x79000000 0x8000>,
+ <0x79020000 0x00 0x79020000 0x8000>;
+ power-domains = <&k3_pds 7 TI_SCI_PD_EXCLUSIVE>;
+ mcu_r5fss0_core0: r5f@79000000 {
+ compatible = "ti,am62-r5f";
+ reg = <0x79000000 0x00008000>,
+ <0x79020000 0x00008000>;
+ reg-names = "atcm", "btcm";
+ ti,sci = <&dmsc>;
+ ti,sci-dev-id = <9>;
+ ti,sci-proc-ids = <0x03 0xff>;
+ resets = <&k3_reset 9 1>;
+ firmware-name = "am62p-mcu-r5f0_0-fw";
+ ti,atcm-enable = <0>;
+ ti,btcm-enable = <1>;
+ ti,loczrama = <0>;
+ };
};
};
diff --git a/arch/arm64/boot/dts/ti/k3-am62p-thermal.dtsi b/arch/arm64/boot/dts/ti/k3-am62p-thermal.dtsi
new file mode 100644
index 0000000000000..85ce545633ea5
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-am62p-thermal.dtsi
@@ -0,0 +1,47 @@
+// SPDX-License-Identifier: GPL-2.0
+
+#include <dt-bindings/thermal/thermal.h>
+
+thermal_zones: thermal-zones {
+ main0_thermal: main0-thermal {
+ polling-delay-passive = <250>; /* milliSeconds */
+ polling-delay = <500>; /* milliSeconds */
+ thermal-sensors = <&wkup_vtm0 0>;
+
+ trips {
+ main0_crit: main0-crit {
+ temperature = <125000>; /* milliCelsius */
+ hysteresis = <2000>; /* milliCelsius */
+ type = "critical";
+ };
+ };
+ };
+
+ main1_thermal: main1-thermal {
+ polling-delay-passive = <250>; /* milliSeconds */
+ polling-delay = <500>; /* milliSeconds */
+ thermal-sensors = <&wkup_vtm0 1>;
+
+ trips {
+ main1_crit: main1-crit {
+ temperature = <125000>; /* milliCelsius */
+ hysteresis = <2000>; /* milliCelsius */
+ type = "critical";
+ };
+ };
+ };
+
+ main2_thermal: main2-thermal {
+ polling-delay-passive = <250>; /* milliSeconds */
+ polling-delay = <500>; /* milliSeconds */
+ thermal-sensors = <&wkup_vtm0 2>;
+
+ trips {
+ main2_crit: main2-crit {
+ temperature = <125000>; /* milliCelsius */
+ hysteresis = <2000>; /* milliCelsius */
+ type = "critical";
+ };
+ };
+ };
+};
diff --git a/arch/arm64/boot/dts/ti/k3-am62p-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-am62p-wakeup.dtsi
index aaf4b793b58e7..19f42b39394ee 100644
--- a/arch/arm64/boot/dts/ti/k3-am62p-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am62p-wakeup.dtsi
@@ -6,17 +6,17 @@
&cbass_wakeup {
wkup_conf: bus@43000000 {
- bootph-all;
compatible = "simple-bus";
reg = <0x00 0x43000000 0x00 0x20000>;
#address-cells = <1>;
#size-cells = <1>;
ranges = <0x00 0x00 0x43000000 0x20000>;
+ bootph-all;
chipid: chipid@14 {
- bootph-all;
compatible = "ti,am654-chipid";
reg = <0x14 0x4>;
+ bootph-all;
};
};
@@ -29,4 +29,69 @@ wkup_uart0: serial@2b300000 {
clock-names = "fclk";
status = "disabled";
};
+
+ wkup_i2c0: i2c@2b200000 {
+ compatible = "ti,am64-i2c", "ti,omap4-i2c";
+ reg = <0x00 0x2b200000 0x00 0x100>;
+ interrupts = <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power-domains = <&k3_pds 107 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 107 4>;
+ clock-names = "fck";
+ status = "disabled";
+ };
+
+ wkup_rtc0: rtc@2b1f0000 {
+ compatible = "ti,am62-rtc";
+ reg = <0x00 0x2b1f0000 0x00 0x100>;
+ interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 117 6> , <&k3_clks 117 0>;
+ clock-names = "vbus", "osc32k";
+ power-domains = <&k3_pds 117 TI_SCI_PD_EXCLUSIVE>;
+ wakeup-source;
+ };
+
+ wkup_rti0: watchdog@2b000000 {
+ compatible = "ti,j7-rti-wdt";
+ reg = <0x00 0x2b000000 0x00 0x100>;
+ clocks = <&k3_clks 132 0>;
+ power-domains = <&k3_pds 132 TI_SCI_PD_EXCLUSIVE>;
+ assigned-clocks = <&k3_clks 132 0>;
+ assigned-clock-parents = <&k3_clks 132 2>;
+ /* Used by DM firmware */
+ status = "reserved";
+ };
+
+ wkup_vtm0: temperature-sensor@b00000 {
+ compatible = "ti,j7200-vtm";
+ reg = <0x00 0xb00000 0x00 0x400>,
+ <0x00 0xb01000 0x00 0x400>;
+ power-domains = <&k3_pds 95 TI_SCI_PD_EXCLUSIVE>;
+ #thermal-sensor-cells = <1>;
+ };
+
+ wkup_r5fss0: r5fss@78000000 {
+ compatible = "ti,am62-r5fss";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x78000000 0x00 0x78000000 0x8000>,
+ <0x78100000 0x00 0x78100000 0x8000>;
+ power-domains = <&k3_pds 119 TI_SCI_PD_EXCLUSIVE>;
+
+ wkup_r5fss0_core0: r5f@78000000 {
+ compatible = "ti,am62-r5f";
+ reg = <0x78000000 0x00008000>,
+ <0x78100000 0x00008000>;
+ reg-names = "atcm", "btcm";
+ ti,sci = <&dmsc>;
+ ti,sci-dev-id = <121>;
+ ti,sci-proc-ids = <0x01 0xff>;
+ resets = <&k3_reset 121 1>;
+ firmware-name = "am62-wkup-r5f0_0-fw";
+ ti,atcm-enable = <1>;
+ ti,btcm-enable = <1>;
+ ti,loczrama = <1>;
+ };
+ };
};
diff --git a/arch/arm64/boot/dts/ti/k3-am62p.dtsi b/arch/arm64/boot/dts/ti/k3-am62p.dtsi
index 294ab73ec98b7..84ffe7b9dcaf3 100644
--- a/arch/arm64/boot/dts/ti/k3-am62p.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am62p.dtsi
@@ -45,10 +45,10 @@ pmu: pmu {
};
cbass_main: bus@f0000 {
- bootph-all;
compatible = "simple-bus";
#address-cells = <2>;
#size-cells = <2>;
+ bootph-all;
ranges = <0x00 0x000f0000 0x00 0x000f0000 0x00 0x00030000>, /* Main MMRs */
<0x00 0x00420000 0x00 0x00420000 0x00 0x00001000>, /* ESM0 */
@@ -100,10 +100,10 @@ cbass_mcu: bus@4000000 {
<0x00 0x79020000 0x00 0x79020000 0x00 0x00008000>, /* MCU R5 BTCM */
<0x00 0x79100000 0x00 0x79100000 0x00 0x00040000>, /* MCU IRAM0 */
<0x00 0x79140000 0x00 0x79140000 0x00 0x00040000>; /* MCU IRAM1 */
+ bootph-all;
};
cbass_wakeup: bus@b00000 {
- bootph-all;
compatible = "simple-bus";
#address-cells = <2>;
#size-cells = <2>;
@@ -112,8 +112,11 @@ cbass_wakeup: bus@b00000 {
<0x00 0x43000000 0x00 0x43000000 0x00 0x00020000>, /* WKUP CTRL MMR */
<0x00 0x78000000 0x00 0x78000000 0x00 0x00008000>, /* DM R5 ATCM*/
<0x00 0x78100000 0x00 0x78100000 0x00 0x00008000>; /* DM R5 BTCM*/
+ bootph-all;
};
};
+
+ #include "k3-am62p-thermal.dtsi"
};
/* Now include peripherals for each bus segment */
--
2.42.0
^ permalink raw reply related [flat|nested] 3+ messages in thread
* [PATCH v3 2/2] arm64: dts: ti: k3-am62p5-sk: Updates for SK EVM
2023-10-19 22:30 [PATCH v3 0/2] arm64: dts: ti: enable more peripherals Bryan Brattlof
2023-10-19 22:30 ` [PATCH v3 1/2] arm64: dts: ti: k3-am62p: Add nodes for more IPs Bryan Brattlof
@ 2023-10-19 22:30 ` Bryan Brattlof
1 sibling, 0 replies; 3+ messages in thread
From: Bryan Brattlof @ 2023-10-19 22:30 UTC (permalink / raw)
To: Nishanth Menon, Vignesh Raghavendra, Tero Kristo, Rob Herring,
Krzysztof Kozlowski, Conor Dooley
Cc: Linux Kernel Mailing List, ARM Linux Mailing List, Bryan Brattlof
From: Vignesh Raghavendra <vigneshr@ti.com>
Update the am62p5-sk board file to enable the new IPs introduced
in the SoC dtb.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
---
arch/arm64/boot/dts/ti/k3-am62p5-sk.dts | 520 +++++++++++++++++++++++-
1 file changed, 502 insertions(+), 18 deletions(-)
diff --git a/arch/arm64/boot/dts/ti/k3-am62p5-sk.dts b/arch/arm64/boot/dts/ti/k3-am62p5-sk.dts
index 6fb17b17c95e8..f377eadef0c12 100644
--- a/arch/arm64/boot/dts/ti/k3-am62p5-sk.dts
+++ b/arch/arm64/boot/dts/ti/k3-am62p5-sk.dts
@@ -8,6 +8,9 @@
/dts-v1/;
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/net/ti-dp83867.h>
#include "k3-am62p5.dtsi"
/ {
@@ -18,6 +21,12 @@ aliases {
serial0 = &wkup_uart0;
serial2 = &main_uart0;
serial3 = &main_uart1;
+ mmc0 = &sdhci0;
+ mmc1 = &sdhci1;
+ mmc2 = &sdhci2;
+ spi0 = &ospi0;
+ ethernet0 = &cpsw_port1;
+ ethernet1 = &cpsw_port2;
};
chosen {
@@ -29,6 +38,7 @@ memory@80000000 {
reg = <0x00000000 0x80000000 0x00000000 0x80000000>,
<0x00000008 0x80000000 0x00000001 0x80000000>;
device_type = "memory";
+ bootph-pre-ram;
};
reserved-memory {
@@ -52,35 +62,511 @@ wkup_r5fss0_core0_memory_region: r5f-dma-memory@9c900000 {
no-map;
};
};
+
+ vmain_pd: regulator-0 {
+ /* TPS65988 PD CONTROLLER OUTPUT */
+ compatible = "regulator-fixed";
+ regulator-name = "vmain_pd";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ bootph-all;
+ };
+
+ vcc_5v0: regulator-1 {
+ /* Output of TPS630702RNMR */
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_5v0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vmain_pd>;
+ regulator-always-on;
+ regulator-boot-on;
+ bootph-all;
+ };
+
+ vdd_mmc1: regulator-2 {
+ /* TPS22918DBVR */
+ compatible = "regulator-fixed";
+ regulator-name = "vdd_mmc1";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ enable-active-high;
+ gpio = <&exp1 3 GPIO_ACTIVE_HIGH>;
+ bootph-all;
+ };
+
+ vddshv_sdio: regulator-3 {
+ compatible = "regulator-gpio";
+ regulator-name = "vddshv_sdio";
+ pinctrl-names = "default";
+ pinctrl-0 = <&vddshv_sdio_pins_default>;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ gpios = <&main_gpio0 31 GPIO_ACTIVE_HIGH>;
+ states = <1800000 0x0>,
+ <3300000 0x1>;
+ bootph-all;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&usr_led_pins_default>;
+
+ led-0 {
+ label = "am62-sk:green:heartbeat";
+ gpios = <&main_gpio1 49 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ function = LED_FUNCTION_HEARTBEAT;
+ default-state = "off";
+ };
+ };
+
+ tlv320_mclk: clk-0 {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <12288000>;
+ };
+
+ codec_audio: sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,name = "AM62x-SKEVM";
+ simple-audio-card,widgets =
+ "Headphone", "Headphone Jack",
+ "Line", "Line In",
+ "Microphone", "Microphone Jack";
+ simple-audio-card,routing =
+ "Headphone Jack", "HPLOUT",
+ "Headphone Jack", "HPROUT",
+ "LINE1L", "Line In",
+ "LINE1R", "Line In",
+ "MIC3R", "Microphone Jack",
+ "Microphone Jack", "Mic Bias";
+ simple-audio-card,format = "dsp_b";
+ simple-audio-card,bitclock-master = <&sound_master>;
+ simple-audio-card,frame-master = <&sound_master>;
+ simple-audio-card,bitclock-inversion;
+
+ simple-audio-card,cpu {
+ sound-dai = <&mcasp1>;
+ };
+
+ sound_master: simple-audio-card,codec {
+ sound-dai = <&tlv320aic3106>;
+ clocks = <&tlv320_mclk>;
+ };
+ };
+};
+
+&main_gpio0 {
+ bootph-all;
+};
+
+&main_gpio1 {
+ bootph-all;
};
&main_pmx0 {
- main_uart0_pins_default: main-uart0-default-pins {
- bootph-all;
+ bootph-all;
+
+ main_i2c0_pins_default: main-i2c0-default-pins {
pinctrl-single,pins = <
- AM62PX_IOPAD(0x1c8, PIN_INPUT, 0) /* (A22) UART0_RXD */
- AM62PX_IOPAD(0x1cc, PIN_OUTPUT, 0) /* (B22) UART0_TXD */
- AM62PX_IOPAD(0x1d0, PIN_INPUT, 0) /* (A23) UART0_CTSn */
- AM62PX_IOPAD(0x1d4, PIN_OUTPUT, 0) /* (C22) UART0_RTSn */
+ AM62PX_IOPAD(0x01e0, PIN_INPUT_PULLUP, 0) /* (B25) I2C0_SCL */
+ AM62PX_IOPAD(0x01e4, PIN_INPUT_PULLUP, 0) /* (A24) I2C0_SDA */
>;
};
- main_uart1_pins_default: main-uart1-default-pins {
- bootph-all;
+ main_i2c1_pins_default: main-i2c1-default-pins {
pinctrl-single,pins = <
- AM62PX_IOPAD(0x194, PIN_INPUT, 2) /* (D25) MCASP0_AXR3 */
- AM62PX_IOPAD(0x198, PIN_OUTPUT, 2) /* (E25) MCASP0_AXR2 */
- AM62PX_IOPAD(0x1ac, PIN_INPUT, 2) /* (G23) MCASP0_AFSR */
- AM62PX_IOPAD(0x1b0, PIN_OUTPUT, 2) /* (G20) MCASP0_ACLKR */
+ AM62PX_IOPAD(0x01e8, PIN_INPUT_PULLUP, 0) /* (C24) I2C1_SCL */
+ AM62PX_IOPAD(0x01ec, PIN_INPUT_PULLUP, 0) /* (B24) I2C1_SDA */
>;
+ bootph-all;
+ };
+
+ main_i2c2_pins_default: main-i2c2-default-pins {
+ pinctrl-single,pins = <
+ AM62PX_IOPAD(0x00b0, PIN_INPUT_PULLUP, 1) /* (T22) GPMC0_CSn2.I2C2_SCL */
+ AM62PX_IOPAD(0x00b4, PIN_INPUT_PULLUP, 1) /* (U25) GPMC0_CSn3.I2C2_SDA */
+ >;
+ };
+
+ main_gpio1_ioexp_intr_pins_default: main-gpio1-ioexp-intr-default-pins {
+ pinctrl-single,pins = <
+ AM62PX_IOPAD(0x01d4, PIN_INPUT, 7) /* (C22) UART0_RTSn.GPIO1_23 */
+ >;
+ };
+
+ main_mcasp1_pins_default: main-mcasp1-default-pins {
+ pinctrl-single,pins = <
+ AM62PX_IOPAD(0x0090, PIN_INPUT, 2) /* (U24) GPMC0_BE0n_CLE.MCASP1_ACLKX */
+ AM62PX_IOPAD(0x0098, PIN_INPUT, 2) /* (AA24) GPMC0_WAIT0.MCASP1_AFSX */
+ AM62PX_IOPAD(0x008c, PIN_INPUT, 2) /* (T25) GPMC0_WEn.MCASP1_AXR0 */
+ AM62PX_IOPAD(0x0084, PIN_INPUT, 2) /* (R25) GPMC0_ADVn_ALE.MCASP1_AXR2 */
+ >;
+ };
+
+ main_mdio1_pins_default: main-mdio1-default-pins {
+ pinctrl-single,pins = <
+ AM62PX_IOPAD(0x0160, PIN_OUTPUT, 0) /* (F17) MDIO0_MDC */
+ AM62PX_IOPAD(0x015c, PIN_INPUT, 0) /* (F16) MDIO0_MDIO */
+ >;
+ };
+
+ main_mmc1_pins_default: main-mmc1-default-pins {
+ pinctrl-single,pins = <
+ AM62PX_IOPAD(0x023c, PIN_INPUT, 0) /* (H20) MMC1_CMD */
+ AM62PX_IOPAD(0x0234, PIN_OUTPUT, 0) /* (J24) MMC1_CLK */
+ AM62PX_IOPAD(0x0230, PIN_INPUT, 0) /* (H21) MMC1_DAT0 */
+ AM62PX_IOPAD(0x022c, PIN_INPUT_PULLUP, 0) /* (H23) MMC1_DAT1 */
+ AM62PX_IOPAD(0x0228, PIN_INPUT_PULLUP, 0) /* (H22) MMC1_DAT2 */
+ AM62PX_IOPAD(0x0224, PIN_INPUT_PULLUP, 0) /* (H25) MMC1_DAT3 */
+ AM62PX_IOPAD(0x0240, PIN_INPUT, 0) /* (D23) MMC1_SDCD */
+ >;
+ bootph-all;
+ };
+
+ main_mmc2_pins_default: main-mmc2-default-pins {
+ pinctrl-single,pins = <
+ AM62PX_IOPAD(0x0120, PIN_INPUT, 0) /* (K24) MMC2_CMD */
+ AM62PX_IOPAD(0x0118, PIN_OUTPUT, 0) /* (K21) MMC2_CLK */
+ AM62PX_IOPAD(0x011C, PIN_INPUT, 0) /* () MMC2_CLKLB */
+ AM62PX_IOPAD(0x0114, PIN_INPUT, 0) /* (K23) MMC2_DAT0 */
+ AM62PX_IOPAD(0x0110, PIN_INPUT_PULLUP, 0) /* (K22) MMC2_DAT1 */
+ AM62PX_IOPAD(0x010c, PIN_INPUT_PULLUP, 0) /* (L20) MMC2_DAT2 */
+ AM62PX_IOPAD(0x0108, PIN_INPUT_PULLUP, 0) /* (L21) MMC2_DAT3 */
+ >;
+ bootph-all;
+ };
+
+ main_rgmii1_pins_default: main-rgmii1-default-pins {
+ pinctrl-single,pins = <
+ AM62PX_IOPAD(0x014c, PIN_INPUT, 0) /* (B15) RGMII1_RD0 */
+ AM62PX_IOPAD(0x0150, PIN_INPUT, 0) /* (B16) RGMII1_RD1 */
+ AM62PX_IOPAD(0x0154, PIN_INPUT, 0) /* (A14) RGMII1_RD2 */
+ AM62PX_IOPAD(0x0158, PIN_INPUT, 0) /* (B14) RGMII1_RD3 */
+ AM62PX_IOPAD(0x0148, PIN_INPUT, 0) /* (A16) RGMII1_RXC */
+ AM62PX_IOPAD(0x0144, PIN_INPUT, 0) /* (A15) RGMII1_RX_CTL */
+ AM62PX_IOPAD(0x0134, PIN_INPUT, 0) /* (A18) RGMII1_TD0 */
+ AM62PX_IOPAD(0x0138, PIN_INPUT, 0) /* (C17) RGMII1_TD1 */
+ AM62PX_IOPAD(0x013c, PIN_INPUT, 0) /* (A17) RGMII1_TD2 */
+ AM62PX_IOPAD(0x0140, PIN_INPUT, 0) /* (C16) RGMII1_TD3 */
+ AM62PX_IOPAD(0x0130, PIN_INPUT, 0) /* (B17) RGMII1_TXC */
+ AM62PX_IOPAD(0x012c, PIN_INPUT, 0) /* (B18) RGMII1_TX_CTL */
+ >;
+ bootph-all;
+ };
+
+ main_rgmii2_pins_default: main-rgmii2-default-pins {
+ pinctrl-single,pins = <
+ AM62PX_IOPAD(0x0184, PIN_INPUT, 0) /* (E19) RGMII2_RD0 */
+ AM62PX_IOPAD(0x0188, PIN_INPUT, 0) /* (E16) RGMII2_RD1 */
+ AM62PX_IOPAD(0x018c, PIN_INPUT, 0) /* (E17) RGMII2_RD2 */
+ AM62PX_IOPAD(0x0190, PIN_INPUT, 0) /* (C19) RGMII2_RD3 */
+ AM62PX_IOPAD(0x0180, PIN_INPUT, 0) /* (D19) RGMII2_RXC */
+ AM62PX_IOPAD(0x017c, PIN_INPUT, 0) /* (F19) RGMII2_RX_CTL */
+ AM62PX_IOPAD(0x016c, PIN_INPUT, 0) /* (B19) RGMII2_TD0 */
+ AM62PX_IOPAD(0x0170, PIN_INPUT, 0) /* (A21) RGMII2_TD1 */
+ AM62PX_IOPAD(0x0174, PIN_INPUT, 0) /* (D17) RGMII2_TD2 */
+ AM62PX_IOPAD(0x0178, PIN_INPUT, 0) /* (A19) RGMII2_TD3 */
+ AM62PX_IOPAD(0x0168, PIN_INPUT, 0) /* (D16) RGMII2_TXC */
+ AM62PX_IOPAD(0x0164, PIN_INPUT, 0) /* (A20) RGMII2_TX_CTL */
+ >;
+ bootph-all;
+ };
+
+ main_uart0_pins_default: main-uart0-default-pins {
+ pinctrl-single,pins = <
+ AM62PX_IOPAD(0x1c8, PIN_INPUT, 0) /* (A22) UART0_RXD */
+ AM62PX_IOPAD(0x1cc, PIN_OUTPUT, 0) /* (B22) UART0_TXD */
+ >;
+ bootph-all;
+ };
+
+ main_uart1_pins_default: main-uart1-default-pins {
+ pinctrl-single,pins = <
+ AM62PX_IOPAD(0x0194, PIN_INPUT, 2) /* (D25) MCASP0_AXR3.UART1_CTSn */
+ AM62PX_IOPAD(0x0198, PIN_OUTPUT, 2) /* (E25) MCASP0_AXR2.UART1_RTSn */
+ AM62PX_IOPAD(0x01ac, PIN_INPUT, 2) /* (G23) MCASP0_AFSR.UART1_RXD */
+ AM62PX_IOPAD(0x01b0, PIN_OUTPUT, 2) /* (G20) MCASP0_ACLKR.UART1_TXD */
+ >;
+ bootph-all;
+ };
+
+ main_wlirq_pins_default: main-wlirq-default-pins {
+ pinctrl-single,pins = <
+ AM62PX_IOPAD(0x0128, PIN_INPUT, 7) /* (K25) MMC2_SDWP.GPIO0_72 */
+ >;
+ };
+
+ ospi0_pins_default: ospi0-default-pins {
+ pinctrl-single,pins = <
+ AM62PX_IOPAD(0x0000, PIN_OUTPUT, 0) /* (P23) OSPI0_CLK */
+ AM62PX_IOPAD(0x002c, PIN_OUTPUT, 0) /* (M25) OSPI0_CSn0 */
+ AM62PX_IOPAD(0x000c, PIN_INPUT, 0) /* (L25) OSPI0_D0 */
+ AM62PX_IOPAD(0x0010, PIN_INPUT, 0) /* (N24) OSPI0_D1 */
+ AM62PX_IOPAD(0x0014, PIN_INPUT, 0) /* (N25) OSPI0_D2 */
+ AM62PX_IOPAD(0x0018, PIN_INPUT, 0) /* (M24) OSPI0_D3 */
+ AM62PX_IOPAD(0x001c, PIN_INPUT, 0) /* (N21) OSPI0_D4 */
+ AM62PX_IOPAD(0x0020, PIN_INPUT, 0) /* (N22) OSPI0_D5 */
+ AM62PX_IOPAD(0x0024, PIN_INPUT, 0) /* (P21) OSPI0_D6 */
+ AM62PX_IOPAD(0x0028, PIN_INPUT, 0) /* (N20) OSPI0_D7 */
+ AM62PX_IOPAD(0x0008, PIN_INPUT, 0) /* (P22) OSPI0_DQS */
+ >;
+ bootph-all;
+ };
+
+ usr_led_pins_default: usr-led-default-pins {
+ pinctrl-single,pins = <
+ AM62PX_IOPAD(0x0244, PIN_INPUT, 7) /* (D24) MMC1_SDWP.GPIO1_49 */
+ >;
+ };
+
+ vddshv_sdio_pins_default: vddshvr-sdio-default-pins {
+ pinctrl-single,pins = <
+ AM62PX_IOPAD(0x007c, PIN_INPUT, 7) /* (Y25) GPMC0_CLK.GPIO0_31 */
+ >;
+ bootph-all;
+ };
+
+ wlan_en_pins_default: wlan-en-default-pins {
+ pinctrl-single,pins = <
+ AM62PX_IOPAD(0x0124, PIN_INPUT, 7) /* (J25) MMC2_SDCD.GPIO0_71 */
+ >;
+ };
+};
+
+&main_i2c1 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_i2c1_pins_default>;
+ clock-frequency = <100000>;
+ bootph-all;
+
+ tlv320aic3106: audio-codec@1b {
+ #sound-dai-cells = <0>;
+ compatible = "ti,tlv320aic3106";
+ reg = <0x1b>;
+ ai3x-micbias-vg = <1>; /* 2.0V */
+ };
+
+ exp1: gpio@22 {
+ compatible = "ti,tca6424";
+ reg = <0x22>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-line-names = "OLDI_INT#", "x8_NAND_DETECT",
+ "UART1_FET_SEL", "MMC1_SD_EN",
+ "VPP_EN", "EXP_PS_3V3_EN",
+ "UART1_FET_BUF_EN", "EXP_HAT_DETECT",
+ "DSI_GPIO0", "DSI_GPIO1",
+ "OLDI_EDID", "BT_UART_WAKE_SOC_3V3",
+ "USB_TYPEA_OC_INDICATION", "CSI_GPIO0",
+ "CSI_GPIO1", "WLAN_ALERTn",
+ "HDMI_INTn", "TEST_GPIO2",
+ "MCASP1_FET_EN", "MCASP1_BUF_BT_EN",
+ "MCASP1_FET_SEL", "DSI_EDID",
+ "PD_I2C_IRQ", "IO_EXP_TEST_LED";
+
+ interrupt-parent = <&main_gpio1>;
+ interrupts = <23 IRQ_TYPE_EDGE_FALLING>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_gpio1_ioexp_intr_pins_default>;
+ bootph-all;
+ };
+
+ exp2: gpio@23 {
+ compatible = "ti,tca6424";
+ reg = <0x23>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-line-names = "BT_EN_SOC", "EXP_PS_5V0_EN",
+ "", "",
+ "", "",
+ "", "",
+ "WL_LT_EN", "",
+ "TP3", "TP6",
+ "TP4", "TP7",
+ "TP5", "TP8",
+ "SoC_I2C2_MCAN_SEL", "GPIO_HDMI_RSTn",
+ "GPIO_CPSW2_RST", "GPIO_CPSW1_RST",
+ "GPIO_OLDI_RSTn", "GPIO_AUD_RSTn",
+ "GPIO_eMMC_RSTn", "SoC_WLAN_SDIO_RST";
+ };
+};
+
+&main_i2c2 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_i2c2_pins_default>;
+ clock-frequency = <400000>;
+};
+
+&sdhci0 {
+ status = "okay";
+ ti,driver-strength-ohm = <50>;
+ disable-wp;
+};
+
+&sdhci1 {
+ /* SD/MMC */
+ status = "okay";
+ vmmc-supply = <&vdd_mmc1>;
+ vqmmc-supply = <&vddshv_sdio>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_mmc1_pins_default>;
+ ti,driver-strength-ohm = <50>;
+ disable-wp;
+ no-1-8-v;
+ bootph-all;
+};
+
+&cpsw3g {
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_rgmii1_pins_default>,
+ <&main_rgmii2_pins_default>;
+};
+
+&cpsw_port1 {
+ phy-mode = "rgmii-rxid";
+ phy-handle = <&cpsw3g_phy0>;
+};
+
+&cpsw_port2 {
+ phy-mode = "rgmii-rxid";
+ phy-handle = <&cpsw3g_phy1>;
+};
+
+&cpsw3g_mdio {
+ cpsw3g_phy0: ethernet-phy@0 {
+ reg = <0>;
+ ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+ ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+ ti,min-output-impedance;
+ };
+
+ cpsw3g_phy1: ethernet-phy@1 {
+ reg = <1>;
+ ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+ ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+ ti,min-output-impedance;
+ };
+};
+
+&mcasp1 {
+ status = "okay";
+ #sound-dai-cells = <0>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_mcasp1_pins_default>;
+
+ op-mode = <0>; /* MCASP_IIS_MODE */
+ tdm-slots = <2>;
+
+ serial-dir = < /* 0: INACTIVE, 1: TX, 2: RX */
+ 1 0 2 0
+ 0 0 0 0
+ 0 0 0 0
+ 0 0 0 0
+ >;
+ tx-num-evt = <32>;
+ rx-num-evt = <32>;
+};
+
+&fss {
+ bootph-all;
+};
+
+&ospi0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&ospi0_pins_default>;
+ bootph-all;
+
+ flash@0{
+ compatible = "jedec,spi-nor";
+ reg = <0x0>;
+ spi-tx-bus-width = <8>;
+ spi-rx-bus-width = <8>;
+ spi-max-frequency = <25000000>;
+ cdns,tshsl-ns = <60>;
+ cdns,tsd2d-ns = <60>;
+ cdns,tchsh-ns = <60>;
+ cdns,tslch-ns = <60>;
+ cdns,read-delay = <4>;
+ bootph-all;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ bootph-all;
+
+ partition@0 {
+ label = "ospi.tiboot3";
+ reg = <0x00 0x80000>;
+ };
+
+ partition@80000 {
+ label = "ospi.tispl";
+ reg = <0x80000 0x200000>;
+ };
+
+ partition@280000 {
+ label = "ospi.u-boot";
+ reg = <0x280000 0x400000>;
+ };
+
+ partition@680000 {
+ label = "ospi.env";
+ reg = <0x680000 0x40000>;
+ };
+
+ partition@6c0000 {
+ label = "ospi.env.backup";
+ reg = <0x6c0000 0x40000>;
+ };
+
+ partition@800000 {
+ label = "ospi.rootfs";
+ reg = <0x800000 0x37c0000>;
+ };
+
+ partition@3fc0000 {
+ label = "ospi.phypattern";
+ reg = <0x3fc0000 0x40000>;
+ bootph-all;
+ };
+ };
+ };
+};
+
+&mailbox0_cluster0 {
+ mbox_r5_0: mbox-r5-0 {
+ ti,mbox-rx = <0 0 0>;
+ ti,mbox-tx = <1 0 0>;
+ };
+};
+
+&mailbox0_cluster1 {
+ mbox_mcu_r5_0: mbox-mcu-r5-0 {
+ ti,mbox-rx = <0 0 0>;
+ ti,mbox-tx = <1 0 0>;
};
};
&main_uart0 {
- bootph-all;
pinctrl-names = "default";
pinctrl-0 = <&main_uart0_pins_default>;
status = "okay";
+ bootph-all;
};
&main_uart1 {
@@ -88,29 +574,27 @@ &main_uart1 {
pinctrl-0 = <&main_uart1_pins_default>;
/* Main UART1 is used by TIFS firmware */
status = "reserved";
-};
-
-&cbass_mcu {
bootph-all;
};
&mcu_pmx0 {
bootph-all;
+
wkup_uart0_pins_default: wkup-uart0-default-pins {
- bootph-all;
pinctrl-single,pins = <
AM62PX_MCU_IOPAD(0x02c, PIN_INPUT, 0) /* (C7) WKUP_UART0_CTSn */
AM62PX_MCU_IOPAD(0x030, PIN_OUTPUT, 0) /* (C6) WKUP_UART0_RTSn */
AM62PX_MCU_IOPAD(0x024, PIN_INPUT, 0) /* (D8) WKUP_UART0_RXD */
AM62PX_MCU_IOPAD(0x028, PIN_OUTPUT, 0) /* (D7) WKUP_UART0_TXD */
>;
+ bootph-all;
};
};
&wkup_uart0 {
/* WKUP UART0 is used by DM firmware */
- bootph-all;
pinctrl-names = "default";
pinctrl-0 = <&wkup_uart0_pins_default>;
status = "reserved";
+ bootph-all;
};
--
2.42.0
^ permalink raw reply related [flat|nested] 3+ messages in thread
end of thread, other threads:[~2023-10-19 22:31 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2023-10-19 22:30 [PATCH v3 0/2] arm64: dts: ti: enable more peripherals Bryan Brattlof
2023-10-19 22:30 ` [PATCH v3 1/2] arm64: dts: ti: k3-am62p: Add nodes for more IPs Bryan Brattlof
2023-10-19 22:30 ` [PATCH v3 2/2] arm64: dts: ti: k3-am62p5-sk: Updates for SK EVM Bryan Brattlof
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).