* [PATCH net-next v5 0/7] Create a binding for the Marvell MV88E6xxx DSA switches
@ 2023-10-23 7:18 Linus Walleij
2023-10-23 7:18 ` [PATCH net-next v5 1/7] dt-bindings: net: dsa: Require ports or ethernet-ports Linus Walleij
` (6 more replies)
0 siblings, 7 replies; 13+ messages in thread
From: Linus Walleij @ 2023-10-23 7:18 UTC (permalink / raw)
To: Andrew Lunn, Gregory Clement, Sebastian Hesselbarth, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Russell King,
Florian Fainelli, Vladimir Oltean, David S. Miller, Eric Dumazet,
Jakub Kicinski, Paolo Abeni
Cc: Christian Marangi, linux-arm-kernel, devicetree, linux-kernel,
netdev, Linus Walleij, Rob Herring, Vladimir Oltean
The Marvell switches are lacking DT bindings.
I need proper schema checking to add LED support to the
Marvell switch. Just how it is, it can't go on like this.
Some Device Tree fixes are included in the series, these
remove the major and most annoying warnings fallout noise:
some warnings remain, and these are of more serious nature,
such as missing phy-mode. They can be applied individually,
or to the networking tree with the rest of the patches.
Thanks to Andrew Lunn, Vladimir Oltean and Russell King
for excellent review and feedback!
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
Changes in v5:
- Consistently rename switch@n to ethernet-switch@n in all cleanup patches
- Consistently rename ports to ethernet-ports in all cleanup patches
- Consistently rename all port@n to ethernet-port@n in all cleanup patches
- Consistently rename all phy@n to ethernet-phy@n in all cleanup patches
- Restore the nodename on the Turris MOX which has a U-Boot binary using the
nodename as ABI, put in a blurb warning about this so no-one else tries
to change it in the future.
- Drop dsa.yaml direct references where we reference dsa.yaml#/$defs/ethernet-ports
- Replace the conjured MV88E6xxx example by a better one based on imx6qdl
plus strictly named nodes and added reset-gpios for a more complete example,
and another example using the interrupt controller based on
armada-381-netgear-gs110emx.dts
- Bump lineage to 2008 as Vladimir says the code was developed starting 2008.
- Link to v4: https://lore.kernel.org/r/20231018-marvell-88e6152-wan-led-v4-0-3ee0c67383be@linaro.org
Changes in v4:
- Rebase the series on top of Rob's series
"dt-bindings: net: Child node schema cleanups" (or the hex numbered
ports will not work)
- Fix up a whitespacing error corrupting v3...
- Add a new patch making the generic DSA binding require ports or
ethernet-ports in the switch node.
- Drop any corrections of port@a in the patches.
- Drop oneOf in the compatible enum for mv88e6xxx
- Use ethernet-switch, ethernet-ports and ethernet-phy in the examples
- Transclude the dsa.yaml#/$defs/ethernet-ports define for ports
- Move the DTS and binding fixes first, before the actual bindings,
so they apply without (too many) warnings as fallout.
- Drop stray colon in text.
- Drop example port in the mveusb binding.
- Link to v3: https://lore.kernel.org/r/20231016-marvell-88e6152-wan-led-v3-0-38cd449dfb15@linaro.org
Changes in v3:
- Fix up a related mvusb example in a different binding that
the scripts were complaining about.
- Fix up the wording on internal vs external MDIO buses in the
mv88e6xxx binding document.
- Remove pointless label and put the right rev-mii into the
MV88E6060 schema.
- Link to v2: https://lore.kernel.org/r/20231014-marvell-88e6152-wan-led-v2-0-7fca08b68849@linaro.org
Changes in v2:
- Break out a separate Marvell MV88E6060 binding file. I stand corrected.
- Drop the idea to rely on nodename mdio-external for the external
MDIO bus, keep the compatible, drop patch for the driver.
- Fix more Marvell DT mistakes.
- Fix NXP DT mistakes in a separate patch.
- Fix Marvell ARM64 mistakes in a separate patch.
- Link to v1: https://lore.kernel.org/r/20231013-marvell-88e6152-wan-led-v1-0-0712ba99857c@linaro.org
---
Linus Walleij (7):
dt-bindings: net: dsa: Require ports or ethernet-ports
dt-bindings: net: mvusb: Fix up DSA example
ARM: dts: marvell: Fix some common switch mistakes
ARM: dts: nxp: Fix some common switch mistakes
ARM64: dts: marvell: Fix some common switch mistakes
dt-bindings: marvell: Rewrite MV88E6xxx in schema
dt-bindings: marvell: Add Marvell MV88E6060 DSA schema
Documentation/devicetree/bindings/net/dsa/dsa.yaml | 6 +
.../bindings/net/dsa/marvell,mv88e6060.yaml | 88 ++++++
.../bindings/net/dsa/marvell,mv88e6xxx.yaml | 330 +++++++++++++++++++++
.../devicetree/bindings/net/dsa/marvell.txt | 109 -------
.../devicetree/bindings/net/marvell,mvusb.yaml | 7 +-
MAINTAINERS | 3 +-
arch/arm/boot/dts/marvell/armada-370-rd.dts | 24 +-
.../dts/marvell/armada-381-netgear-gs110emx.dts | 44 ++-
.../dts/marvell/armada-385-clearfog-gtr-l8.dts | 38 +--
.../dts/marvell/armada-385-clearfog-gtr-s4.dts | 22 +-
arch/arm/boot/dts/marvell/armada-385-linksys.dtsi | 18 +-
.../boot/dts/marvell/armada-385-turris-omnia.dts | 20 +-
arch/arm/boot/dts/marvell/armada-388-clearfog.dts | 20 +-
.../boot/dts/marvell/armada-xp-linksys-mamba.dts | 18 +-
arch/arm/boot/dts/nxp/vf/vf610-zii-cfu1.dts | 14 +-
arch/arm/boot/dts/nxp/vf/vf610-zii-scu4-aib.dts | 70 ++---
arch/arm/boot/dts/nxp/vf/vf610-zii-spb4.dts | 18 +-
arch/arm/boot/dts/nxp/vf/vf610-zii-ssmb-dtu.dts | 20 +-
arch/arm/boot/dts/nxp/vf/vf610-zii-ssmb-spu3.dts | 18 +-
.../dts/marvell/armada-3720-espressobin-ultra.dts | 14 +-
.../boot/dts/marvell/armada-3720-espressobin.dtsi | 20 +-
.../boot/dts/marvell/armada-3720-gl-mv1000.dts | 20 +-
.../boot/dts/marvell/armada-3720-turris-mox.dts | 189 ++++++------
.../boot/dts/marvell/armada-7040-mochabin.dts | 24 +-
.../dts/marvell/armada-8040-clearfog-gt-8k.dts | 22 +-
arch/arm64/boot/dts/marvell/cn9130-crb.dtsi | 42 ++-
26 files changed, 761 insertions(+), 457 deletions(-)
---
base-commit: 1c9be5fea84e409542a186893d219bf7cff22f5a
change-id: 20231008-marvell-88e6152-wan-led-88c43b7fd2fd
Best regards,
--
Linus Walleij <linus.walleij@linaro.org>
^ permalink raw reply [flat|nested] 13+ messages in thread
* [PATCH net-next v5 1/7] dt-bindings: net: dsa: Require ports or ethernet-ports
2023-10-23 7:18 [PATCH net-next v5 0/7] Create a binding for the Marvell MV88E6xxx DSA switches Linus Walleij
@ 2023-10-23 7:18 ` Linus Walleij
2023-10-23 7:51 ` Linus Walleij
2023-10-23 17:40 ` Rob Herring
2023-10-23 7:18 ` [PATCH net-next v5 2/7] dt-bindings: net: mvusb: Fix up DSA example Linus Walleij
` (5 subsequent siblings)
6 siblings, 2 replies; 13+ messages in thread
From: Linus Walleij @ 2023-10-23 7:18 UTC (permalink / raw)
To: Andrew Lunn, Gregory Clement, Sebastian Hesselbarth, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Russell King,
Florian Fainelli, Vladimir Oltean, David S. Miller, Eric Dumazet,
Jakub Kicinski, Paolo Abeni
Cc: Christian Marangi, linux-arm-kernel, devicetree, linux-kernel,
netdev, Linus Walleij, Rob Herring
Bindings using dsa.yaml#/$defs/ethernet-ports specify that
a DSA switch node need to have a ports or ethernet-ports
subnode, and that is actually required, so add requirements
using oneOf.
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
Documentation/devicetree/bindings/net/dsa/dsa.yaml | 6 ++++++
1 file changed, 6 insertions(+)
diff --git a/Documentation/devicetree/bindings/net/dsa/dsa.yaml b/Documentation/devicetree/bindings/net/dsa/dsa.yaml
index 6107189d276a..368169f7fd37 100644
--- a/Documentation/devicetree/bindings/net/dsa/dsa.yaml
+++ b/Documentation/devicetree/bindings/net/dsa/dsa.yaml
@@ -46,4 +46,10 @@ $defs:
$ref: dsa-port.yaml#
unevaluatedProperties: false
+ oneOf:
+ - required:
+ - ports
+ - required:
+ - ethernet-ports
+
...
--
2.34.1
^ permalink raw reply related [flat|nested] 13+ messages in thread
* [PATCH net-next v5 2/7] dt-bindings: net: mvusb: Fix up DSA example
2023-10-23 7:18 [PATCH net-next v5 0/7] Create a binding for the Marvell MV88E6xxx DSA switches Linus Walleij
2023-10-23 7:18 ` [PATCH net-next v5 1/7] dt-bindings: net: dsa: Require ports or ethernet-ports Linus Walleij
@ 2023-10-23 7:18 ` Linus Walleij
2023-10-23 19:49 ` Rob Herring
2023-10-23 7:18 ` [PATCH net-next v5 3/7] ARM: dts: marvell: Fix some common switch mistakes Linus Walleij
` (4 subsequent siblings)
6 siblings, 1 reply; 13+ messages in thread
From: Linus Walleij @ 2023-10-23 7:18 UTC (permalink / raw)
To: Andrew Lunn, Gregory Clement, Sebastian Hesselbarth, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Russell King,
Florian Fainelli, Vladimir Oltean, David S. Miller, Eric Dumazet,
Jakub Kicinski, Paolo Abeni
Cc: Christian Marangi, linux-arm-kernel, devicetree, linux-kernel,
netdev, Linus Walleij, Vladimir Oltean
When adding a proper schema for the Marvell mx88e6xxx switch,
the scripts start complaining about this embedded example:
dtschema/dtc warnings/errors:
net/marvell,mvusb.example.dtb: switch@0: ports: '#address-cells'
is a required property
from schema $id: http://devicetree.org/schemas/net/dsa/marvell,mv88e6xxx.yaml#
net/marvell,mvusb.example.dtb: switch@0: ports: '#size-cells'
is a required property
from schema $id: http://devicetree.org/schemas/net/dsa/marvell,mv88e6xxx.yaml#
Fix this up by extending the example with those properties in
the ports node.
While we are at it, rename "ports" to "ethernet-ports" and rename
"switch" to "ethernet-switch" as this is recommended practice.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
Documentation/devicetree/bindings/net/marvell,mvusb.yaml | 7 +++++--
1 file changed, 5 insertions(+), 2 deletions(-)
diff --git a/Documentation/devicetree/bindings/net/marvell,mvusb.yaml b/Documentation/devicetree/bindings/net/marvell,mvusb.yaml
index 3a3325168048..ab838c1ffeed 100644
--- a/Documentation/devicetree/bindings/net/marvell,mvusb.yaml
+++ b/Documentation/devicetree/bindings/net/marvell,mvusb.yaml
@@ -50,11 +50,14 @@ examples:
#address-cells = <1>;
#size-cells = <0>;
- switch@0 {
+ ethernet-switch@0 {
compatible = "marvell,mv88e6190";
reg = <0x0>;
- ports {
+ ethernet-ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
/* Port definitions */
};
--
2.34.1
^ permalink raw reply related [flat|nested] 13+ messages in thread
* [PATCH net-next v5 3/7] ARM: dts: marvell: Fix some common switch mistakes
2023-10-23 7:18 [PATCH net-next v5 0/7] Create a binding for the Marvell MV88E6xxx DSA switches Linus Walleij
2023-10-23 7:18 ` [PATCH net-next v5 1/7] dt-bindings: net: dsa: Require ports or ethernet-ports Linus Walleij
2023-10-23 7:18 ` [PATCH net-next v5 2/7] dt-bindings: net: mvusb: Fix up DSA example Linus Walleij
@ 2023-10-23 7:18 ` Linus Walleij
2023-10-23 7:18 ` [PATCH net-next v5 4/7] ARM: dts: nxp: " Linus Walleij
` (3 subsequent siblings)
6 siblings, 0 replies; 13+ messages in thread
From: Linus Walleij @ 2023-10-23 7:18 UTC (permalink / raw)
To: Andrew Lunn, Gregory Clement, Sebastian Hesselbarth, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Russell King,
Florian Fainelli, Vladimir Oltean, David S. Miller, Eric Dumazet,
Jakub Kicinski, Paolo Abeni
Cc: Christian Marangi, linux-arm-kernel, devicetree, linux-kernel,
netdev, Linus Walleij
Fix some errors in the Marvell MV88E6xxx switch descriptions:
- The top node had no address size or cells.
- switch0@0 is not OK, should be ethernet-switch@0.
- The ports node should be named ethernet-ports
- The ethernet-ports node should have port@0 etc children, no
plural "ports" in the children.
- Ports should be named ethernet-port@0 etc
- PHYs should be named ethernet-phy@0 etc
This serves as an example of fixes needed for introducing a
schema for the bindings, but the patch can simply be applied.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
arch/arm/boot/dts/marvell/armada-370-rd.dts | 24 ++++++------
.../dts/marvell/armada-381-netgear-gs110emx.dts | 44 +++++++++++-----------
.../dts/marvell/armada-385-clearfog-gtr-l8.dts | 38 +++++++++----------
.../dts/marvell/armada-385-clearfog-gtr-s4.dts | 22 +++++------
arch/arm/boot/dts/marvell/armada-385-linksys.dtsi | 18 ++++-----
.../boot/dts/marvell/armada-385-turris-omnia.dts | 20 +++++-----
arch/arm/boot/dts/marvell/armada-388-clearfog.dts | 20 +++++-----
.../boot/dts/marvell/armada-xp-linksys-mamba.dts | 18 ++++-----
8 files changed, 96 insertions(+), 108 deletions(-)
diff --git a/arch/arm/boot/dts/marvell/armada-370-rd.dts b/arch/arm/boot/dts/marvell/armada-370-rd.dts
index b459a670f615..1b241da11e94 100644
--- a/arch/arm/boot/dts/marvell/armada-370-rd.dts
+++ b/arch/arm/boot/dts/marvell/armada-370-rd.dts
@@ -149,39 +149,37 @@ led@0 {
};
};
- switch: switch@10 {
+ switch: ethernet-switch@10 {
compatible = "marvell,mv88e6085";
- #address-cells = <1>;
- #size-cells = <0>;
reg = <0x10>;
interrupt-controller;
#interrupt-cells = <2>;
- ports {
+ ethernet-ports {
#address-cells = <1>;
#size-cells = <0>;
- port@0 {
+ ethernet-port@0 {
reg = <0>;
label = "lan0";
};
- port@1 {
+ ethernet-port@1 {
reg = <1>;
label = "lan1";
};
- port@2 {
+ ethernet-port@2 {
reg = <2>;
label = "lan2";
};
- port@3 {
+ ethernet-port@3 {
reg = <3>;
label = "lan3";
};
- port@5 {
+ ethernet-port@5 {
reg = <5>;
ethernet = <ð1>;
phy-mode = "rgmii-id";
@@ -196,25 +194,25 @@ mdio {
#address-cells = <1>;
#size-cells = <0>;
- switchphy0: switchphy@0 {
+ switchphy0: ethernet-phy@0 {
reg = <0>;
interrupt-parent = <&switch>;
interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
};
- switchphy1: switchphy@1 {
+ switchphy1: ethernet-phy@1 {
reg = <1>;
interrupt-parent = <&switch>;
interrupts = <1 IRQ_TYPE_LEVEL_HIGH>;
};
- switchphy2: switchphy@2 {
+ switchphy2: ethernet-phy@2 {
reg = <2>;
interrupt-parent = <&switch>;
interrupts = <2 IRQ_TYPE_LEVEL_HIGH>;
};
- switchphy3: switchphy@3 {
+ switchphy3: ethernet-phy@3 {
reg = <3>;
interrupt-parent = <&switch>;
interrupts = <3 IRQ_TYPE_LEVEL_HIGH>;
diff --git a/arch/arm/boot/dts/marvell/armada-381-netgear-gs110emx.dts b/arch/arm/boot/dts/marvell/armada-381-netgear-gs110emx.dts
index f4c4b213ef4e..5baf83e5253d 100644
--- a/arch/arm/boot/dts/marvell/armada-381-netgear-gs110emx.dts
+++ b/arch/arm/boot/dts/marvell/armada-381-netgear-gs110emx.dts
@@ -77,51 +77,49 @@ &mdio {
pinctrl-0 = <&mdio_pins>;
status = "okay";
- switch@0 {
+ ethernet-switch@0 {
compatible = "marvell,mv88e6190";
- #address-cells = <1>;
#interrupt-cells = <2>;
interrupt-controller;
interrupt-parent = <&gpio1>;
interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
pinctrl-0 = <&switch_interrupt_pins>;
pinctrl-names = "default";
- #size-cells = <0>;
reg = <0>;
mdio {
#address-cells = <1>;
#size-cells = <0>;
- switch0phy1: switch0phy1@1 {
+ switch0phy1: ethernet-phy@1 {
reg = <0x1>;
};
- switch0phy2: switch0phy2@2 {
+ switch0phy2: ethernet-phy@2 {
reg = <0x2>;
};
- switch0phy3: switch0phy3@3 {
+ switch0phy3: ethernet-phy@3 {
reg = <0x3>;
};
- switch0phy4: switch0phy4@4 {
+ switch0phy4: ethernet-phy@4 {
reg = <0x4>;
};
- switch0phy5: switch0phy5@5 {
+ switch0phy5: ethernet-phy@5 {
reg = <0x5>;
};
- switch0phy6: switch0phy6@6 {
+ switch0phy6: ethernet-phy@6 {
reg = <0x6>;
};
- switch0phy7: switch0phy7@7 {
+ switch0phy7: ethernet-phy@7 {
reg = <0x7>;
};
- switch0phy8: switch0phy8@8 {
+ switch0phy8: ethernet-phy@8 {
reg = <0x8>;
};
};
@@ -142,11 +140,11 @@ phy2: ethernet-phy@c {
};
};
- ports {
+ ethernet-ports {
#address-cells = <1>;
#size-cells = <0>;
- port@0 {
+ ethernet-port@0 {
ethernet = <ð0>;
phy-mode = "rgmii";
reg = <0>;
@@ -158,55 +156,55 @@ fixed-link {
};
};
- port@1 {
+ ethernet-port@1 {
label = "lan1";
phy-handle = <&switch0phy1>;
reg = <1>;
};
- port@2 {
+ ethernet-port@2 {
label = "lan2";
phy-handle = <&switch0phy2>;
reg = <2>;
};
- port@3 {
+ ethernet-port@3 {
label = "lan3";
phy-handle = <&switch0phy3>;
reg = <3>;
};
- port@4 {
+ ethernet-port@4 {
label = "lan4";
phy-handle = <&switch0phy4>;
reg = <4>;
};
- port@5 {
+ ethernet-port@5 {
label = "lan5";
phy-handle = <&switch0phy5>;
reg = <5>;
};
- port@6 {
+ ethernet-port@6 {
label = "lan6";
phy-handle = <&switch0phy6>;
reg = <6>;
};
- port@7 {
+ ethernet-port@7 {
label = "lan7";
phy-handle = <&switch0phy7>;
reg = <7>;
};
- port@8 {
+ ethernet-port@8 {
label = "lan8";
phy-handle = <&switch0phy8>;
reg = <8>;
};
- port@9 {
+ ethernet-port@9 {
/* 88X3310P external phy */
label = "lan9";
phy-handle = <&phy1>;
@@ -214,7 +212,7 @@ port@9 {
reg = <9>;
};
- port@a {
+ ethernet-port@a {
/* 88X3310P external phy */
label = "lan10";
phy-handle = <&phy2>;
diff --git a/arch/arm/boot/dts/marvell/armada-385-clearfog-gtr-l8.dts b/arch/arm/boot/dts/marvell/armada-385-clearfog-gtr-l8.dts
index 1990f7d0cc79..1707d1b01545 100644
--- a/arch/arm/boot/dts/marvell/armada-385-clearfog-gtr-l8.dts
+++ b/arch/arm/boot/dts/marvell/armada-385-clearfog-gtr-l8.dts
@@ -7,66 +7,66 @@ / {
};
&mdio {
- switch0: switch0@4 {
+ switch0: ethernet-switch@4 {
compatible = "marvell,mv88e6190";
reg = <4>;
pinctrl-names = "default";
pinctrl-0 = <&cf_gtr_switch_reset_pins>;
reset-gpios = <&gpio0 18 GPIO_ACTIVE_LOW>;
- ports {
+ ethernet-ports {
#address-cells = <1>;
#size-cells = <0>;
- port@1 {
+ ethernet-port@1 {
reg = <1>;
label = "lan8";
phy-handle = <&switch0phy0>;
};
- port@2 {
+ ethernet-port@2 {
reg = <2>;
label = "lan7";
phy-handle = <&switch0phy1>;
};
- port@3 {
+ ethernet-port@3 {
reg = <3>;
label = "lan6";
phy-handle = <&switch0phy2>;
};
- port@4 {
+ ethernet-port@4 {
reg = <4>;
label = "lan5";
phy-handle = <&switch0phy3>;
};
- port@5 {
+ ethernet-port@5 {
reg = <5>;
label = "lan4";
phy-handle = <&switch0phy4>;
};
- port@6 {
+ ethernet-port@6 {
reg = <6>;
label = "lan3";
phy-handle = <&switch0phy5>;
};
- port@7 {
+ ethernet-port@7 {
reg = <7>;
label = "lan2";
phy-handle = <&switch0phy6>;
};
- port@8 {
+ ethernet-port@8 {
reg = <8>;
label = "lan1";
phy-handle = <&switch0phy7>;
};
- port@10 {
+ ethernet-port@10 {
reg = <10>;
phy-mode = "2500base-x";
@@ -83,35 +83,35 @@ mdio {
#address-cells = <1>;
#size-cells = <0>;
- switch0phy0: switch0phy0@1 {
+ switch0phy0: ethernet-phy@1 {
reg = <0x1>;
};
- switch0phy1: switch0phy1@2 {
+ switch0phy1: ethernet-phy@2 {
reg = <0x2>;
};
- switch0phy2: switch0phy2@3 {
+ switch0phy2: ethernet-phy@3 {
reg = <0x3>;
};
- switch0phy3: switch0phy3@4 {
+ switch0phy3: ethernet-phy@4 {
reg = <0x4>;
};
- switch0phy4: switch0phy4@5 {
+ switch0phy4: ethernet-phy@5 {
reg = <0x5>;
};
- switch0phy5: switch0phy5@6 {
+ switch0phy5: ethernet-phy@6 {
reg = <0x6>;
};
- switch0phy6: switch0phy6@7 {
+ switch0phy6: ethernet-phy@7 {
reg = <0x7>;
};
- switch0phy7: switch0phy7@8 {
+ switch0phy7: ethernet-phy@8 {
reg = <0x8>;
};
};
diff --git a/arch/arm/boot/dts/marvell/armada-385-clearfog-gtr-s4.dts b/arch/arm/boot/dts/marvell/armada-385-clearfog-gtr-s4.dts
index b795ad573891..a7678a784c18 100644
--- a/arch/arm/boot/dts/marvell/armada-385-clearfog-gtr-s4.dts
+++ b/arch/arm/boot/dts/marvell/armada-385-clearfog-gtr-s4.dts
@@ -11,42 +11,42 @@ &sfp0 {
};
&mdio {
- switch0: switch0@4 {
+ switch0: ethernet-switch@4 {
compatible = "marvell,mv88e6085";
reg = <4>;
pinctrl-names = "default";
pinctrl-0 = <&cf_gtr_switch_reset_pins>;
reset-gpios = <&gpio0 18 GPIO_ACTIVE_LOW>;
- ports {
+ ethernet-ports {
#address-cells = <1>;
#size-cells = <0>;
- port@1 {
+ ethernet-port@1 {
reg = <1>;
label = "lan2";
phy-handle = <&switch0phy0>;
};
- port@2 {
+ ethernet-port@2 {
reg = <2>;
label = "lan1";
phy-handle = <&switch0phy1>;
};
- port@3 {
+ ethernet-port@3 {
reg = <3>;
label = "lan4";
phy-handle = <&switch0phy2>;
};
- port@4 {
+ ethernet-port@4 {
reg = <4>;
label = "lan3";
phy-handle = <&switch0phy3>;
};
- port@5 {
+ ethernet-port@5 {
reg = <5>;
phy-mode = "2500base-x";
ethernet = <ð1>;
@@ -63,19 +63,19 @@ mdio {
#address-cells = <1>;
#size-cells = <0>;
- switch0phy0: switch0phy0@11 {
+ switch0phy0: ethernet-phy@11 {
reg = <0x11>;
};
- switch0phy1: switch0phy1@12 {
+ switch0phy1: ethernet-phy@12 {
reg = <0x12>;
};
- switch0phy2: switch0phy2@13 {
+ switch0phy2: ethernet-phy@13 {
reg = <0x13>;
};
- switch0phy3: switch0phy3@14 {
+ switch0phy3: ethernet-phy@14 {
reg = <0x14>;
};
};
diff --git a/arch/arm/boot/dts/marvell/armada-385-linksys.dtsi b/arch/arm/boot/dts/marvell/armada-385-linksys.dtsi
index fc8216fd9f60..4116ed60f709 100644
--- a/arch/arm/boot/dts/marvell/armada-385-linksys.dtsi
+++ b/arch/arm/boot/dts/marvell/armada-385-linksys.dtsi
@@ -158,42 +158,40 @@ nand: nand@0 {
&mdio {
status = "okay";
- switch@0 {
+ ethernet-switch@0 {
compatible = "marvell,mv88e6085";
- #address-cells = <1>;
- #size-cells = <0>;
reg = <0>;
- ports {
+ ethernet-ports {
#address-cells = <1>;
#size-cells = <0>;
- port@0 {
+ ethernet-port@0 {
reg = <0>;
label = "lan4";
};
- port@1 {
+ ethernet-port@1 {
reg = <1>;
label = "lan3";
};
- port@2 {
+ ethernet-port@2 {
reg = <2>;
label = "lan2";
};
- port@3 {
+ ethernet-port@3 {
reg = <3>;
label = "lan1";
};
- port@4 {
+ ethernet-port@4 {
reg = <4>;
label = "wan";
};
- port@5 {
+ ethernet-port@5 {
reg = <5>;
phy-mode = "sgmii";
ethernet = <ð2>;
diff --git a/arch/arm/boot/dts/marvell/armada-385-turris-omnia.dts b/arch/arm/boot/dts/marvell/armada-385-turris-omnia.dts
index 2d8d319bec83..7b755bb4e4e7 100644
--- a/arch/arm/boot/dts/marvell/armada-385-turris-omnia.dts
+++ b/arch/arm/boot/dts/marvell/armada-385-turris-omnia.dts
@@ -435,12 +435,10 @@ phy1: ethernet-phy@1 {
};
/* Switch MV88E6176 at address 0x10 */
- switch@10 {
+ ethernet-switch@10 {
pinctrl-names = "default";
pinctrl-0 = <&swint_pins>;
compatible = "marvell,mv88e6085";
- #address-cells = <1>;
- #size-cells = <0>;
dsa,member = <0 0>;
reg = <0x10>;
@@ -448,36 +446,36 @@ switch@10 {
interrupt-parent = <&gpio1>;
interrupts = <13 IRQ_TYPE_LEVEL_LOW>;
- ports {
+ ethernet-ports {
#address-cells = <1>;
#size-cells = <0>;
- ports@0 {
+ ethernet-port@0 {
reg = <0>;
label = "lan0";
};
- ports@1 {
+ ethernet-port@1 {
reg = <1>;
label = "lan1";
};
- ports@2 {
+ ethernet-port@2 {
reg = <2>;
label = "lan2";
};
- ports@3 {
+ ethernet-port@3 {
reg = <3>;
label = "lan3";
};
- ports@4 {
+ ethernet-port@4 {
reg = <4>;
label = "lan4";
};
- ports@5 {
+ ethernet-port@5 {
reg = <5>;
ethernet = <ð1>;
phy-mode = "rgmii-id";
@@ -488,7 +486,7 @@ fixed-link {
};
};
- ports@6 {
+ ethernet-port@6 {
reg = <6>;
ethernet = <ð0>;
phy-mode = "rgmii-id";
diff --git a/arch/arm/boot/dts/marvell/armada-388-clearfog.dts b/arch/arm/boot/dts/marvell/armada-388-clearfog.dts
index 32c569df142f..3290ccad2374 100644
--- a/arch/arm/boot/dts/marvell/armada-388-clearfog.dts
+++ b/arch/arm/boot/dts/marvell/armada-388-clearfog.dts
@@ -92,44 +92,42 @@ pcie2-0-w-disable-hog {
&mdio {
status = "okay";
- switch@4 {
+ ethernet-switch@4 {
compatible = "marvell,mv88e6085";
- #address-cells = <1>;
- #size-cells = <0>;
reg = <4>;
pinctrl-0 = <&clearfog_dsa0_clk_pins &clearfog_dsa0_pins>;
pinctrl-names = "default";
- ports {
+ ethernet-ports {
#address-cells = <1>;
#size-cells = <0>;
- port@0 {
+ ethernet-port@0 {
reg = <0>;
label = "lan5";
};
- port@1 {
+ ethernet-port@1 {
reg = <1>;
label = "lan4";
};
- port@2 {
+ ethernet-port@2 {
reg = <2>;
label = "lan3";
};
- port@3 {
+ ethernet-port@3 {
reg = <3>;
label = "lan2";
};
- port@4 {
+ ethernet-port@4 {
reg = <4>;
label = "lan1";
};
- port@5 {
+ ethernet-port@5 {
reg = <5>;
ethernet = <ð1>;
phy-mode = "1000base-x";
@@ -140,7 +138,7 @@ fixed-link {
};
};
- port@6 {
+ ethernet-port@6 {
/* 88E1512 external phy */
reg = <6>;
label = "lan6";
diff --git a/arch/arm/boot/dts/marvell/armada-xp-linksys-mamba.dts b/arch/arm/boot/dts/marvell/armada-xp-linksys-mamba.dts
index 7a0614fd0c93..ea859f7ea042 100644
--- a/arch/arm/boot/dts/marvell/armada-xp-linksys-mamba.dts
+++ b/arch/arm/boot/dts/marvell/armada-xp-linksys-mamba.dts
@@ -265,42 +265,40 @@ flash@0 {
&mdio {
status = "okay";
- switch@0 {
+ ethernet-switch@0 {
compatible = "marvell,mv88e6085";
- #address-cells = <1>;
- #size-cells = <0>;
reg = <0>;
- ports {
+ ethernet-ports {
#address-cells = <1>;
#size-cells = <0>;
- port@0 {
+ ethernet-port@0 {
reg = <0>;
label = "lan4";
};
- port@1 {
+ ethernet-port@1 {
reg = <1>;
label = "lan3";
};
- port@2 {
+ ethernet-port@2 {
reg = <2>;
label = "lan2";
};
- port@3 {
+ ethernet-port@3 {
reg = <3>;
label = "lan1";
};
- port@4 {
+ ethernet-port@4 {
reg = <4>;
label = "internet";
};
- port@5 {
+ ethernet-port@5 {
reg = <5>;
phy-mode = "rgmii-id";
ethernet = <ð0>;
--
2.34.1
^ permalink raw reply related [flat|nested] 13+ messages in thread
* [PATCH net-next v5 4/7] ARM: dts: nxp: Fix some common switch mistakes
2023-10-23 7:18 [PATCH net-next v5 0/7] Create a binding for the Marvell MV88E6xxx DSA switches Linus Walleij
` (2 preceding siblings ...)
2023-10-23 7:18 ` [PATCH net-next v5 3/7] ARM: dts: marvell: Fix some common switch mistakes Linus Walleij
@ 2023-10-23 7:18 ` Linus Walleij
2023-10-23 7:18 ` [PATCH net-next v5 5/7] ARM64: dts: marvell: " Linus Walleij
` (2 subsequent siblings)
6 siblings, 0 replies; 13+ messages in thread
From: Linus Walleij @ 2023-10-23 7:18 UTC (permalink / raw)
To: Andrew Lunn, Gregory Clement, Sebastian Hesselbarth, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Russell King,
Florian Fainelli, Vladimir Oltean, David S. Miller, Eric Dumazet,
Jakub Kicinski, Paolo Abeni
Cc: Christian Marangi, linux-arm-kernel, devicetree, linux-kernel,
netdev, Linus Walleij
Fix some errors in the Marvell MV88E6xxx switch descriptions:
- switch0@0 is not OK, should be ethernet-switch@0
- ports should be ethernet-ports
- port should be ethernet-port
- phy should be ethernet-phy
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
arch/arm/boot/dts/nxp/vf/vf610-zii-cfu1.dts | 14 ++---
arch/arm/boot/dts/nxp/vf/vf610-zii-scu4-aib.dts | 70 ++++++++++++------------
arch/arm/boot/dts/nxp/vf/vf610-zii-spb4.dts | 18 +++---
arch/arm/boot/dts/nxp/vf/vf610-zii-ssmb-dtu.dts | 20 +++----
arch/arm/boot/dts/nxp/vf/vf610-zii-ssmb-spu3.dts | 18 +++---
5 files changed, 70 insertions(+), 70 deletions(-)
diff --git a/arch/arm/boot/dts/nxp/vf/vf610-zii-cfu1.dts b/arch/arm/boot/dts/nxp/vf/vf610-zii-cfu1.dts
index 1a19aec8957b..7e72f860c3c5 100644
--- a/arch/arm/boot/dts/nxp/vf/vf610-zii-cfu1.dts
+++ b/arch/arm/boot/dts/nxp/vf/vf610-zii-cfu1.dts
@@ -162,7 +162,7 @@ mdio1: mdio {
suppress-preamble;
status = "okay";
- switch0: switch0@0 {
+ switch0: ethernet-switch@0 {
compatible = "marvell,mv88e6085";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_switch>;
@@ -173,26 +173,26 @@ switch0: switch0@0 {
interrupt-controller;
#interrupt-cells = <2>;
- ports {
+ ethernet-ports {
#address-cells = <1>;
#size-cells = <0>;
- port@0 {
+ ethernet-port@0 {
reg = <0>;
label = "eth_cu_1000_1";
};
- port@1 {
+ ethernet-port@1 {
reg = <1>;
label = "eth_cu_1000_2";
};
- port@2 {
+ ethernet-port@2 {
reg = <2>;
label = "eth_cu_1000_3";
};
- port@5 {
+ ethernet-port@5 {
reg = <5>;
label = "eth_fc_1000_1";
phy-mode = "1000base-x";
@@ -200,7 +200,7 @@ port@5 {
sfp = <&sff>;
};
- port@6 {
+ ethernet-port@6 {
reg = <6>;
phy-mode = "rmii";
ethernet = <&fec1>;
diff --git a/arch/arm/boot/dts/nxp/vf/vf610-zii-scu4-aib.dts b/arch/arm/boot/dts/nxp/vf/vf610-zii-scu4-aib.dts
index df1335492a19..77492eeea450 100644
--- a/arch/arm/boot/dts/nxp/vf/vf610-zii-scu4-aib.dts
+++ b/arch/arm/boot/dts/nxp/vf/vf610-zii-scu4-aib.dts
@@ -47,17 +47,17 @@ mdio_mux_1: mdio@1 {
#address-cells = <1>;
#size-cells = <0>;
- switch0: switch0@0 {
+ switch0: ethernet-switch@0 {
compatible = "marvell,mv88e6190";
reg = <0>;
dsa,member = <0 0>;
eeprom-length = <65536>;
- ports {
+ ethernet-ports {
#address-cells = <1>;
#size-cells = <0>;
- port@0 {
+ ethernet-port@0 {
reg = <0>;
phy-mode = "rmii";
ethernet = <&fec1>;
@@ -68,37 +68,37 @@ fixed-link {
};
};
- port@1 {
+ ethernet-port@1 {
reg = <1>;
label = "aib2main_1";
};
- port@2 {
+ ethernet-port@2 {
reg = <2>;
label = "aib2main_2";
};
- port@3 {
+ ethernet-port@3 {
reg = <3>;
label = "eth_cu_1000_5";
};
- port@4 {
+ ethernet-port@4 {
reg = <4>;
label = "eth_cu_1000_6";
};
- port@5 {
+ ethernet-port@5 {
reg = <5>;
label = "eth_cu_1000_4";
};
- port@6 {
+ ethernet-port@6 {
reg = <6>;
label = "eth_cu_1000_7";
};
- port@7 {
+ ethernet-port@7 {
reg = <7>;
label = "modem_pic";
@@ -108,7 +108,7 @@ fixed-link {
};
};
- switch0port10: port@10 {
+ switch0port10: ethernet-port@10 {
reg = <10>;
label = "dsa";
phy-mode = "xgmii";
@@ -130,32 +130,32 @@ mdio_mux_2: mdio@2 {
#address-cells = <1>;
#size-cells = <0>;
- switch1: switch1@0 {
+ switch1: ethernet-switch@0 {
compatible = "marvell,mv88e6190";
reg = <0>;
dsa,member = <0 1>;
eeprom-length = <65536>;
- ports {
+ ethernet-ports {
#address-cells = <1>;
#size-cells = <0>;
- port@1 {
+ ethernet-port@1 {
reg = <1>;
label = "eth_cu_1000_3";
};
- port@2 {
+ ethernet-port@2 {
reg = <2>;
label = "eth_cu_100_2";
};
- port@3 {
+ ethernet-port@3 {
reg = <3>;
label = "eth_cu_100_3";
};
- switch1port9: port@9 {
+ switch1port9: ethernet-port@9 {
reg = <9>;
label = "dsa";
phy-mode = "xgmii";
@@ -168,7 +168,7 @@ fixed-link {
};
};
- switch1port10: port@10 {
+ switch1port10: ethernet-port@10 {
reg = <10>;
label = "dsa";
phy-mode = "xgmii";
@@ -188,17 +188,17 @@ mdio_mux_4: mdio@4 {
#address-cells = <1>;
#size-cells = <0>;
- switch2: switch2@0 {
+ switch2: ethernet-switch@0 {
compatible = "marvell,mv88e6190";
reg = <0>;
dsa,member = <0 2>;
eeprom-length = <65536>;
- ports {
+ ethernet-ports {
#address-cells = <1>;
#size-cells = <0>;
- port@2 {
+ ethernet-port@2 {
reg = <2>;
label = "eth_fc_1000_2";
phy-mode = "1000base-x";
@@ -206,7 +206,7 @@ port@2 {
sfp = <&sff1>;
};
- port@3 {
+ ethernet-port@3 {
reg = <3>;
label = "eth_fc_1000_3";
phy-mode = "1000base-x";
@@ -214,7 +214,7 @@ port@3 {
sfp = <&sff2>;
};
- port@4 {
+ ethernet-port@4 {
reg = <4>;
label = "eth_fc_1000_4";
phy-mode = "1000base-x";
@@ -222,7 +222,7 @@ port@4 {
sfp = <&sff3>;
};
- port@5 {
+ ethernet-port@5 {
reg = <5>;
label = "eth_fc_1000_5";
phy-mode = "1000base-x";
@@ -230,7 +230,7 @@ port@5 {
sfp = <&sff4>;
};
- port@6 {
+ ethernet-port@6 {
reg = <6>;
label = "eth_fc_1000_6";
phy-mode = "1000base-x";
@@ -238,7 +238,7 @@ port@6 {
sfp = <&sff5>;
};
- port@7 {
+ ethernet-port@7 {
reg = <7>;
label = "eth_fc_1000_7";
phy-mode = "1000base-x";
@@ -246,7 +246,7 @@ port@7 {
sfp = <&sff6>;
};
- port@9 {
+ ethernet-port@9 {
reg = <9>;
label = "eth_fc_1000_1";
phy-mode = "1000base-x";
@@ -254,7 +254,7 @@ port@9 {
sfp = <&sff0>;
};
- switch2port10: port@10 {
+ switch2port10: ethernet-port@10 {
reg = <10>;
label = "dsa";
phy-mode = "2500base-x";
@@ -276,17 +276,17 @@ mdio_mux_8: mdio@8 {
#address-cells = <1>;
#size-cells = <0>;
- switch3: switch3@0 {
+ switch3: ethernet-switch@0 {
compatible = "marvell,mv88e6190";
reg = <0>;
dsa,member = <0 3>;
eeprom-length = <65536>;
- ports {
+ ethernet-ports {
#address-cells = <1>;
#size-cells = <0>;
- port@2 {
+ ethernet-port@2 {
reg = <2>;
label = "eth_fc_1000_8";
phy-mode = "1000base-x";
@@ -294,7 +294,7 @@ port@2 {
sfp = <&sff7>;
};
- port@3 {
+ ethernet-port@3 {
reg = <3>;
label = "eth_fc_1000_9";
phy-mode = "1000base-x";
@@ -302,7 +302,7 @@ port@3 {
sfp = <&sff8>;
};
- port@4 {
+ ethernet-port@4 {
reg = <4>;
label = "eth_fc_1000_10";
phy-mode = "1000base-x";
@@ -310,7 +310,7 @@ port@4 {
sfp = <&sff9>;
};
- switch3port9: port@9 {
+ switch3port9: ethernet-port@9 {
reg = <9>;
label = "dsa";
phy-mode = "2500base-x";
@@ -322,7 +322,7 @@ fixed-link {
};
};
- switch3port10: port@10 {
+ switch3port10: ethernet-port@10 {
reg = <10>;
label = "dsa";
phy-mode = "xgmii";
diff --git a/arch/arm/boot/dts/nxp/vf/vf610-zii-spb4.dts b/arch/arm/boot/dts/nxp/vf/vf610-zii-spb4.dts
index 1461804ecaea..2a490464660c 100644
--- a/arch/arm/boot/dts/nxp/vf/vf610-zii-spb4.dts
+++ b/arch/arm/boot/dts/nxp/vf/vf610-zii-spb4.dts
@@ -123,7 +123,7 @@ mdio1: mdio {
suppress-preamble;
status = "okay";
- switch0: switch0@0 {
+ switch0: ethernet-switch@0 {
compatible = "marvell,mv88e6190";
pinctrl-0 = <&pinctrl_gpio_switch0>;
pinctrl-names = "default";
@@ -134,11 +134,11 @@ switch0: switch0@0 {
interrupt-controller;
#interrupt-cells = <2>;
- ports {
+ ethernet-ports {
#address-cells = <1>;
#size-cells = <0>;
- port@0 {
+ ethernet-port@0 {
reg = <0>;
phy-mode = "rmii";
ethernet = <&fec1>;
@@ -149,32 +149,32 @@ fixed-link {
};
};
- port@1 {
+ ethernet-port@1 {
reg = <1>;
label = "eth_cu_1000_1";
};
- port@2 {
+ ethernet-port@2 {
reg = <2>;
label = "eth_cu_1000_2";
};
- port@3 {
+ ethernet-port@3 {
reg = <3>;
label = "eth_cu_1000_3";
};
- port@4 {
+ ethernet-port@4 {
reg = <4>;
label = "eth_cu_1000_4";
};
- port@5 {
+ ethernet-port@5 {
reg = <5>;
label = "eth_cu_1000_5";
};
- port@6 {
+ ethernet-port@6 {
reg = <6>;
label = "eth_cu_1000_6";
};
diff --git a/arch/arm/boot/dts/nxp/vf/vf610-zii-ssmb-dtu.dts b/arch/arm/boot/dts/nxp/vf/vf610-zii-ssmb-dtu.dts
index 463c2452b9b7..078d8699e16d 100644
--- a/arch/arm/boot/dts/nxp/vf/vf610-zii-ssmb-dtu.dts
+++ b/arch/arm/boot/dts/nxp/vf/vf610-zii-ssmb-dtu.dts
@@ -112,7 +112,7 @@ mdio1: mdio {
suppress-preamble;
status = "okay";
- switch0: switch0@0 {
+ switch0: ethernet-switch@0 {
compatible = "marvell,mv88e6190";
pinctrl-0 = <&pinctrl_gpio_switch0>;
pinctrl-names = "default";
@@ -123,11 +123,11 @@ switch0: switch0@0 {
interrupt-controller;
#interrupt-cells = <2>;
- ports {
+ ethernet-ports {
#address-cells = <1>;
#size-cells = <0>;
- port@0 {
+ ethernet-port@0 {
reg = <0>;
phy-mode = "rmii";
ethernet = <&fec1>;
@@ -138,27 +138,27 @@ fixed-link {
};
};
- port@1 {
+ ethernet-port@1 {
reg = <1>;
label = "eth_cu_100_3";
};
- port@5 {
+ ethernet-port@5 {
reg = <5>;
label = "eth_cu_1000_4";
};
- port@6 {
+ ethernet-port@6 {
reg = <6>;
label = "eth_cu_1000_5";
};
- port@8 {
+ ethernet-port@8 {
reg = <8>;
label = "eth_cu_1000_1";
};
- port@9 {
+ ethernet-port@9 {
reg = <9>;
label = "eth_cu_1000_2";
phy-handle = <&phy9>;
@@ -167,12 +167,12 @@ port@9 {
};
};
- mdio1 {
+ mdio-external {
compatible = "marvell,mv88e6xxx-mdio-external";
#address-cells = <1>;
#size-cells = <0>;
- phy9: phy9@0 {
+ phy9: ethernet-phy@0 {
compatible = "ethernet-phy-ieee802.3-c45";
pinctrl-0 = <&pinctrl_gpio_phy9>;
pinctrl-names = "default";
diff --git a/arch/arm/boot/dts/nxp/vf/vf610-zii-ssmb-spu3.dts b/arch/arm/boot/dts/nxp/vf/vf610-zii-ssmb-spu3.dts
index f5ae0d5de315..22c8f44390a9 100644
--- a/arch/arm/boot/dts/nxp/vf/vf610-zii-ssmb-spu3.dts
+++ b/arch/arm/boot/dts/nxp/vf/vf610-zii-ssmb-spu3.dts
@@ -137,7 +137,7 @@ mdio1: mdio {
suppress-preamble;
status = "okay";
- switch0: switch0@0 {
+ switch0: ethernet-switch@0 {
compatible = "marvell,mv88e6190";
pinctrl-0 = <&pinctrl_gpio_switch0>;
pinctrl-names = "default";
@@ -148,11 +148,11 @@ switch0: switch0@0 {
interrupt-controller;
#interrupt-cells = <2>;
- ports {
+ ethernet-ports {
#address-cells = <1>;
#size-cells = <0>;
- port@0 {
+ ethernet-port@0 {
reg = <0>;
phy-mode = "rmii";
ethernet = <&fec1>;
@@ -163,32 +163,32 @@ fixed-link {
};
};
- port@1 {
+ ethernet-port@1 {
reg = <1>;
label = "eth_cu_1000_1";
};
- port@2 {
+ ethernet-port@2 {
reg = <2>;
label = "eth_cu_1000_2";
};
- port@3 {
+ ethernet-port@3 {
reg = <3>;
label = "eth_cu_1000_3";
};
- port@4 {
+ ethernet-port@4 {
reg = <4>;
label = "eth_cu_1000_4";
};
- port@5 {
+ ethernet-port@5 {
reg = <5>;
label = "eth_cu_1000_5";
};
- port@6 {
+ ethernet-port@6 {
reg = <6>;
label = "eth_cu_1000_6";
};
--
2.34.1
^ permalink raw reply related [flat|nested] 13+ messages in thread
* [PATCH net-next v5 5/7] ARM64: dts: marvell: Fix some common switch mistakes
2023-10-23 7:18 [PATCH net-next v5 0/7] Create a binding for the Marvell MV88E6xxx DSA switches Linus Walleij
` (3 preceding siblings ...)
2023-10-23 7:18 ` [PATCH net-next v5 4/7] ARM: dts: nxp: " Linus Walleij
@ 2023-10-23 7:18 ` Linus Walleij
2023-10-23 7:18 ` [PATCH net-next v5 6/7] dt-bindings: marvell: Rewrite MV88E6xxx in schema Linus Walleij
2023-10-23 7:18 ` [PATCH net-next v5 7/7] dt-bindings: marvell: Add Marvell MV88E6060 DSA schema Linus Walleij
6 siblings, 0 replies; 13+ messages in thread
From: Linus Walleij @ 2023-10-23 7:18 UTC (permalink / raw)
To: Andrew Lunn, Gregory Clement, Sebastian Hesselbarth, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Russell King,
Florian Fainelli, Vladimir Oltean, David S. Miller, Eric Dumazet,
Jakub Kicinski, Paolo Abeni
Cc: Christian Marangi, linux-arm-kernel, devicetree, linux-kernel,
netdev, Linus Walleij
Fix some errors in the Marvell MV88E6xxx switch descriptions:
- The top node had no address size or cells.
- switch0@0 is not OK, should be ethernet-switch@0.
- ports should be ethernet-ports
- port@0 should be ethernet-port@0
- PHYs should be named ethernet-phy@
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
.../dts/marvell/armada-3720-espressobin-ultra.dts | 14 +-
.../boot/dts/marvell/armada-3720-espressobin.dtsi | 20 +--
.../boot/dts/marvell/armada-3720-gl-mv1000.dts | 20 +--
.../boot/dts/marvell/armada-3720-turris-mox.dts | 189 +++++++++++----------
.../boot/dts/marvell/armada-7040-mochabin.dts | 24 ++-
.../dts/marvell/armada-8040-clearfog-gt-8k.dts | 22 +--
arch/arm64/boot/dts/marvell/cn9130-crb.dtsi | 42 +++--
7 files changed, 164 insertions(+), 167 deletions(-)
diff --git a/arch/arm64/boot/dts/marvell/armada-3720-espressobin-ultra.dts b/arch/arm64/boot/dts/marvell/armada-3720-espressobin-ultra.dts
index f9abef8dcc94..870bb380a40a 100644
--- a/arch/arm64/boot/dts/marvell/armada-3720-espressobin-ultra.dts
+++ b/arch/arm64/boot/dts/marvell/armada-3720-espressobin-ultra.dts
@@ -126,32 +126,32 @@ &switch0 {
reset-gpios = <&gpiosb 23 GPIO_ACTIVE_LOW>;
- ports {
- switch0port1: port@1 {
+ ethernet-ports {
+ switch0port1: ethernet-port@1 {
reg = <1>;
label = "lan0";
phy-handle = <&switch0phy0>;
};
- switch0port2: port@2 {
+ switch0port2: ethernet-port@2 {
reg = <2>;
label = "lan1";
phy-handle = <&switch0phy1>;
};
- switch0port3: port@3 {
+ switch0port3: ethernet-port@3 {
reg = <3>;
label = "lan2";
phy-handle = <&switch0phy2>;
};
- switch0port4: port@4 {
+ switch0port4: ethernet-port@4 {
reg = <4>;
label = "lan3";
phy-handle = <&switch0phy3>;
};
- switch0port5: port@5 {
+ switch0port5: ethernet-port@5 {
reg = <5>;
label = "wan";
phy-handle = <&extphy>;
@@ -160,7 +160,7 @@ switch0port5: port@5 {
};
mdio {
- switch0phy3: switch0phy3@14 {
+ switch0phy3: ethernet-phy@14 {
reg = <0x14>;
};
};
diff --git a/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dtsi b/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dtsi
index 5fc613d24151..86ec0df1c676 100644
--- a/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dtsi
@@ -145,19 +145,17 @@ &usb2 {
};
&mdio {
- switch0: switch0@1 {
+ switch0: ethernet-switch@1 {
compatible = "marvell,mv88e6085";
- #address-cells = <1>;
- #size-cells = <0>;
reg = <1>;
dsa,member = <0 0>;
- ports {
+ ethernet-ports {
#address-cells = <1>;
#size-cells = <0>;
- switch0port0: port@0 {
+ switch0port0: ethernet-port@0 {
reg = <0>;
label = "cpu";
ethernet = <ð0>;
@@ -168,19 +166,19 @@ fixed-link {
};
};
- switch0port1: port@1 {
+ switch0port1: ethernet-port@1 {
reg = <1>;
label = "wan";
phy-handle = <&switch0phy0>;
};
- switch0port2: port@2 {
+ switch0port2: ethernet-port@2 {
reg = <2>;
label = "lan0";
phy-handle = <&switch0phy1>;
};
- switch0port3: port@3 {
+ switch0port3: ethernet-port@3 {
reg = <3>;
label = "lan1";
phy-handle = <&switch0phy2>;
@@ -192,13 +190,13 @@ mdio {
#address-cells = <1>;
#size-cells = <0>;
- switch0phy0: switch0phy0@11 {
+ switch0phy0: ethernet-phy@11 {
reg = <0x11>;
};
- switch0phy1: switch0phy1@12 {
+ switch0phy1: ethernet-phy@12 {
reg = <0x12>;
};
- switch0phy2: switch0phy2@13 {
+ switch0phy2: ethernet-phy@13 {
reg = <0x13>;
};
};
diff --git a/arch/arm64/boot/dts/marvell/armada-3720-gl-mv1000.dts b/arch/arm64/boot/dts/marvell/armada-3720-gl-mv1000.dts
index b1b45b4fa9d4..63fbc8352161 100644
--- a/arch/arm64/boot/dts/marvell/armada-3720-gl-mv1000.dts
+++ b/arch/arm64/boot/dts/marvell/armada-3720-gl-mv1000.dts
@@ -152,31 +152,29 @@ &uart0 {
};
&mdio {
- switch0: switch0@1 {
+ switch0: ethernet-switch@1 {
compatible = "marvell,mv88e6085";
- #address-cells = <1>;
- #size-cells = <0>;
reg = <1>;
dsa,member = <0 0>;
- ports: ports {
+ ports: ethernet-ports {
#address-cells = <1>;
#size-cells = <0>;
- port@0 {
+ ethernet-port@0 {
reg = <0>;
label = "cpu";
ethernet = <ð0>;
};
- port@1 {
+ ethernet-port@1 {
reg = <1>;
label = "wan";
phy-handle = <&switch0phy0>;
};
- port@2 {
+ ethernet-port@2 {
reg = <2>;
label = "lan0";
phy-handle = <&switch0phy1>;
@@ -185,7 +183,7 @@ port@2 {
nvmem-cell-names = "mac-address";
};
- port@3 {
+ ethernet-port@3 {
reg = <3>;
label = "lan1";
phy-handle = <&switch0phy2>;
@@ -199,13 +197,13 @@ mdio {
#address-cells = <1>;
#size-cells = <0>;
- switch0phy0: switch0phy0@11 {
+ switch0phy0: ethernet-phy@11 {
reg = <0x11>;
};
- switch0phy1: switch0phy1@12 {
+ switch0phy1: ethernet-phy@12 {
reg = <0x12>;
};
- switch0phy2: switch0phy2@13 {
+ switch0phy2: ethernet-phy@13 {
reg = <0x13>;
};
};
diff --git a/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts b/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts
index 9eab2bb22134..cdf1b8bdb230 100644
--- a/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts
+++ b/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts
@@ -304,7 +304,12 @@ phy1: ethernet-phy@1 {
reg = <1>;
};
- /* switch nodes are enabled by U-Boot if modules are present */
+ /*
+ * NOTE: switch nodes are enabled by U-Boot if modules are present
+ * DO NOT change this node name (switch0@10) even if it is not following
+ * conventions! Deployed U-Boot binaries are explicitly looking for
+ * this node in order to augment the device tree!
+ */
switch0@10 {
compatible = "marvell,mv88e6190";
reg = <0x10>;
@@ -317,92 +322,92 @@ mdio {
#address-cells = <1>;
#size-cells = <0>;
- switch0phy1: switch0phy1@1 {
+ switch0phy1: ethernet-phy@1 {
reg = <0x1>;
};
- switch0phy2: switch0phy2@2 {
+ switch0phy2: ethernet-phy@2 {
reg = <0x2>;
};
- switch0phy3: switch0phy3@3 {
+ switch0phy3: ethernet-phy@3 {
reg = <0x3>;
};
- switch0phy4: switch0phy4@4 {
+ switch0phy4: ethernet-phy@4 {
reg = <0x4>;
};
- switch0phy5: switch0phy5@5 {
+ switch0phy5: ethernet-phy@5 {
reg = <0x5>;
};
- switch0phy6: switch0phy6@6 {
+ switch0phy6: ethernet-phy@6 {
reg = <0x6>;
};
- switch0phy7: switch0phy7@7 {
+ switch0phy7: ethernet-phy@7 {
reg = <0x7>;
};
- switch0phy8: switch0phy8@8 {
+ switch0phy8: ethernet-phy@8 {
reg = <0x8>;
};
};
- ports {
+ ethernet-ports {
#address-cells = <1>;
#size-cells = <0>;
- port@1 {
+ ethernet-port@1 {
reg = <0x1>;
label = "lan1";
phy-handle = <&switch0phy1>;
};
- port@2 {
+ ethernet-port@2 {
reg = <0x2>;
label = "lan2";
phy-handle = <&switch0phy2>;
};
- port@3 {
+ ethernet-port@3 {
reg = <0x3>;
label = "lan3";
phy-handle = <&switch0phy3>;
};
- port@4 {
+ ethernet-port@4 {
reg = <0x4>;
label = "lan4";
phy-handle = <&switch0phy4>;
};
- port@5 {
+ ethernet-port@5 {
reg = <0x5>;
label = "lan5";
phy-handle = <&switch0phy5>;
};
- port@6 {
+ ethernet-port@6 {
reg = <0x6>;
label = "lan6";
phy-handle = <&switch0phy6>;
};
- port@7 {
+ ethernet-port@7 {
reg = <0x7>;
label = "lan7";
phy-handle = <&switch0phy7>;
};
- port@8 {
+ ethernet-port@8 {
reg = <0x8>;
label = "lan8";
phy-handle = <&switch0phy8>;
};
- port@9 {
+ ethernet-port@9 {
reg = <0x9>;
label = "cpu";
ethernet = <ð1>;
@@ -410,7 +415,7 @@ port@9 {
managed = "in-band-status";
};
- switch0port10: port@a {
+ switch0port10: ethernet-port@a {
reg = <0xa>;
label = "dsa";
phy-mode = "2500base-x";
@@ -430,7 +435,7 @@ port-sfp@a {
};
};
- switch0@2 {
+ ethernet-switch@2 {
compatible = "marvell,mv88e6085";
reg = <0x2>;
dsa,member = <0 0>;
@@ -442,52 +447,52 @@ mdio {
#address-cells = <1>;
#size-cells = <0>;
- switch0phy1_topaz: switch0phy1@11 {
+ switch0phy1_topaz: ethernet-phy@11 {
reg = <0x11>;
};
- switch0phy2_topaz: switch0phy2@12 {
+ switch0phy2_topaz: ethernet-phy@12 {
reg = <0x12>;
};
- switch0phy3_topaz: switch0phy3@13 {
+ switch0phy3_topaz: ethernet-phy@13 {
reg = <0x13>;
};
- switch0phy4_topaz: switch0phy4@14 {
+ switch0phy4_topaz: ethernet-phy@14 {
reg = <0x14>;
};
};
- ports {
+ ethernet-ports {
#address-cells = <1>;
#size-cells = <0>;
- port@1 {
+ ethernet-port@1 {
reg = <0x1>;
label = "lan1";
phy-handle = <&switch0phy1_topaz>;
};
- port@2 {
+ ethernet-port@2 {
reg = <0x2>;
label = "lan2";
phy-handle = <&switch0phy2_topaz>;
};
- port@3 {
+ ethernet-port@3 {
reg = <0x3>;
label = "lan3";
phy-handle = <&switch0phy3_topaz>;
};
- port@4 {
+ ethernet-port@4 {
reg = <0x4>;
label = "lan4";
phy-handle = <&switch0phy4_topaz>;
};
- port@5 {
+ ethernet-port@5 {
reg = <0x5>;
label = "cpu";
phy-mode = "2500base-x";
@@ -497,7 +502,7 @@ port@5 {
};
};
- switch1@11 {
+ ethernet-switch@11 {
compatible = "marvell,mv88e6190";
reg = <0x11>;
dsa,member = <0 1>;
@@ -509,92 +514,92 @@ mdio {
#address-cells = <1>;
#size-cells = <0>;
- switch1phy1: switch1phy1@1 {
+ switch1phy1: ethernet-phy@1 {
reg = <0x1>;
};
- switch1phy2: switch1phy2@2 {
+ switch1phy2: ethernet-phy@2 {
reg = <0x2>;
};
- switch1phy3: switch1phy3@3 {
+ switch1phy3: ethernet-phy@3 {
reg = <0x3>;
};
- switch1phy4: switch1phy4@4 {
+ switch1phy4: ethernet-phy@4 {
reg = <0x4>;
};
- switch1phy5: switch1phy5@5 {
+ switch1phy5: ethernet-phy@5 {
reg = <0x5>;
};
- switch1phy6: switch1phy6@6 {
+ switch1phy6: ethernet-phy@6 {
reg = <0x6>;
};
- switch1phy7: switch1phy7@7 {
+ switch1phy7: ethernet-phy@7 {
reg = <0x7>;
};
- switch1phy8: switch1phy8@8 {
+ switch1phy8: ethernet-phy@8 {
reg = <0x8>;
};
};
- ports {
+ ethernet-ports {
#address-cells = <1>;
#size-cells = <0>;
- port@1 {
+ ethernet-port@1 {
reg = <0x1>;
label = "lan9";
phy-handle = <&switch1phy1>;
};
- port@2 {
+ ethernet-port@2 {
reg = <0x2>;
label = "lan10";
phy-handle = <&switch1phy2>;
};
- port@3 {
+ ethernet-port@3 {
reg = <0x3>;
label = "lan11";
phy-handle = <&switch1phy3>;
};
- port@4 {
+ ethernet-port@4 {
reg = <0x4>;
label = "lan12";
phy-handle = <&switch1phy4>;
};
- port@5 {
+ ethernet-port@5 {
reg = <0x5>;
label = "lan13";
phy-handle = <&switch1phy5>;
};
- port@6 {
+ ethernet-port@6 {
reg = <0x6>;
label = "lan14";
phy-handle = <&switch1phy6>;
};
- port@7 {
+ ethernet-port@7 {
reg = <0x7>;
label = "lan15";
phy-handle = <&switch1phy7>;
};
- port@8 {
+ ethernet-port@8 {
reg = <0x8>;
label = "lan16";
phy-handle = <&switch1phy8>;
};
- switch1port9: port@9 {
+ switch1port9: ethernet-port@9 {
reg = <0x9>;
label = "dsa";
phy-mode = "2500base-x";
@@ -602,7 +607,7 @@ switch1port9: port@9 {
link = <&switch0port10>;
};
- switch1port10: port@a {
+ switch1port10: ethernet-port@a {
reg = <0xa>;
label = "dsa";
phy-mode = "2500base-x";
@@ -622,7 +627,7 @@ port-sfp@a {
};
};
- switch1@2 {
+ ethernet-switch@2 {
compatible = "marvell,mv88e6085";
reg = <0x2>;
dsa,member = <0 1>;
@@ -634,52 +639,52 @@ mdio {
#address-cells = <1>;
#size-cells = <0>;
- switch1phy1_topaz: switch1phy1@11 {
+ switch1phy1_topaz: ethernet-phy@11 {
reg = <0x11>;
};
- switch1phy2_topaz: switch1phy2@12 {
+ switch1phy2_topaz: ethernet-phy@12 {
reg = <0x12>;
};
- switch1phy3_topaz: switch1phy3@13 {
+ switch1phy3_topaz: ethernet-phy@13 {
reg = <0x13>;
};
- switch1phy4_topaz: switch1phy4@14 {
+ switch1phy4_topaz: ethernet-phy@14 {
reg = <0x14>;
};
};
- ports {
+ ethernet-ports {
#address-cells = <1>;
#size-cells = <0>;
- port@1 {
+ ethernet-port@1 {
reg = <0x1>;
label = "lan9";
phy-handle = <&switch1phy1_topaz>;
};
- port@2 {
+ ethernet-port@2 {
reg = <0x2>;
label = "lan10";
phy-handle = <&switch1phy2_topaz>;
};
- port@3 {
+ ethernet-port@3 {
reg = <0x3>;
label = "lan11";
phy-handle = <&switch1phy3_topaz>;
};
- port@4 {
+ ethernet-port@4 {
reg = <0x4>;
label = "lan12";
phy-handle = <&switch1phy4_topaz>;
};
- port@5 {
+ ethernet-port@5 {
reg = <0x5>;
label = "dsa";
phy-mode = "2500base-x";
@@ -689,7 +694,7 @@ port@5 {
};
};
- switch2@12 {
+ ethernet-switch@12 {
compatible = "marvell,mv88e6190";
reg = <0x12>;
dsa,member = <0 2>;
@@ -701,92 +706,92 @@ mdio {
#address-cells = <1>;
#size-cells = <0>;
- switch2phy1: switch2phy1@1 {
+ switch2phy1: ethernet-phy@1 {
reg = <0x1>;
};
- switch2phy2: switch2phy2@2 {
+ switch2phy2: ethernet-phy@2 {
reg = <0x2>;
};
- switch2phy3: switch2phy3@3 {
+ switch2phy3: ethernet-phy@3 {
reg = <0x3>;
};
- switch2phy4: switch2phy4@4 {
+ switch2phy4: ethernet-phy@4 {
reg = <0x4>;
};
- switch2phy5: switch2phy5@5 {
+ switch2phy5: ethernet-phy@5 {
reg = <0x5>;
};
- switch2phy6: switch2phy6@6 {
+ switch2phy6: ethernet-phy@6 {
reg = <0x6>;
};
- switch2phy7: switch2phy7@7 {
+ switch2phy7: ethernet-phy@7 {
reg = <0x7>;
};
- switch2phy8: switch2phy8@8 {
+ switch2phy8: ethernet-phy@8 {
reg = <0x8>;
};
};
- ports {
+ ethernet-ports {
#address-cells = <1>;
#size-cells = <0>;
- port@1 {
+ ethernet-port@1 {
reg = <0x1>;
label = "lan17";
phy-handle = <&switch2phy1>;
};
- port@2 {
+ ethernet-port@2 {
reg = <0x2>;
label = "lan18";
phy-handle = <&switch2phy2>;
};
- port@3 {
+ ethernet-port@3 {
reg = <0x3>;
label = "lan19";
phy-handle = <&switch2phy3>;
};
- port@4 {
+ ethernet-port@4 {
reg = <0x4>;
label = "lan20";
phy-handle = <&switch2phy4>;
};
- port@5 {
+ ethernet-port@5 {
reg = <0x5>;
label = "lan21";
phy-handle = <&switch2phy5>;
};
- port@6 {
+ ethernet-port@6 {
reg = <0x6>;
label = "lan22";
phy-handle = <&switch2phy6>;
};
- port@7 {
+ ethernet-port@7 {
reg = <0x7>;
label = "lan23";
phy-handle = <&switch2phy7>;
};
- port@8 {
+ ethernet-port@8 {
reg = <0x8>;
label = "lan24";
phy-handle = <&switch2phy8>;
};
- switch2port9: port@9 {
+ switch2port9: ethernet-port@9 {
reg = <0x9>;
label = "dsa";
phy-mode = "2500base-x";
@@ -805,7 +810,7 @@ port-sfp@a {
};
};
- switch2@2 {
+ ethernet-switch@2 {
compatible = "marvell,mv88e6085";
reg = <0x2>;
dsa,member = <0 2>;
@@ -817,52 +822,52 @@ mdio {
#address-cells = <1>;
#size-cells = <0>;
- switch2phy1_topaz: switch2phy1@11 {
+ switch2phy1_topaz: ethernet-phy@11 {
reg = <0x11>;
};
- switch2phy2_topaz: switch2phy2@12 {
+ switch2phy2_topaz: ethernet-phy@12 {
reg = <0x12>;
};
- switch2phy3_topaz: switch2phy3@13 {
+ switch2phy3_topaz: ethernet-phy@13 {
reg = <0x13>;
};
- switch2phy4_topaz: switch2phy4@14 {
+ switch2phy4_topaz: ethernet-phy@14 {
reg = <0x14>;
};
};
- ports {
+ ethernet-ports {
#address-cells = <1>;
#size-cells = <0>;
- port@1 {
+ ethernet-port@1 {
reg = <0x1>;
label = "lan17";
phy-handle = <&switch2phy1_topaz>;
};
- port@2 {
+ ethernet-port@2 {
reg = <0x2>;
label = "lan18";
phy-handle = <&switch2phy2_topaz>;
};
- port@3 {
+ ethernet-port@3 {
reg = <0x3>;
label = "lan19";
phy-handle = <&switch2phy3_topaz>;
};
- port@4 {
+ ethernet-port@4 {
reg = <0x4>;
label = "lan20";
phy-handle = <&switch2phy4_topaz>;
};
- port@5 {
+ ethernet-port@5 {
reg = <0x5>;
label = "dsa";
phy-mode = "2500base-x";
diff --git a/arch/arm64/boot/dts/marvell/armada-7040-mochabin.dts b/arch/arm64/boot/dts/marvell/armada-7040-mochabin.dts
index 48202810bf78..40b7ee7ead72 100644
--- a/arch/arm64/boot/dts/marvell/armada-7040-mochabin.dts
+++ b/arch/arm64/boot/dts/marvell/armada-7040-mochabin.dts
@@ -301,10 +301,8 @@ eth2phy: ethernet-phy@1 {
};
/* 88E6141 Topaz switch */
- switch: switch@3 {
+ switch: ethernet-switch@3 {
compatible = "marvell,mv88e6085";
- #address-cells = <1>;
- #size-cells = <0>;
reg = <3>;
pinctrl-names = "default";
@@ -314,35 +312,35 @@ switch: switch@3 {
interrupt-parent = <&cp0_gpio1>;
interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
- ports {
+ ethernet-ports {
#address-cells = <1>;
#size-cells = <0>;
- swport1: port@1 {
+ swport1: ethernet-port@1 {
reg = <1>;
label = "lan0";
phy-handle = <&swphy1>;
};
- swport2: port@2 {
+ swport2: ethernet-port@2 {
reg = <2>;
label = "lan1";
phy-handle = <&swphy2>;
};
- swport3: port@3 {
+ swport3: ethernet-port@3 {
reg = <3>;
label = "lan2";
phy-handle = <&swphy3>;
};
- swport4: port@4 {
+ swport4: ethernet-port@4 {
reg = <4>;
label = "lan3";
phy-handle = <&swphy4>;
};
- port@5 {
+ ethernet-port@5 {
reg = <5>;
label = "cpu";
ethernet = <&cp0_eth1>;
@@ -355,19 +353,19 @@ mdio {
#address-cells = <1>;
#size-cells = <0>;
- swphy1: swphy1@17 {
+ swphy1: ethernet-phy@17 {
reg = <17>;
};
- swphy2: swphy2@18 {
+ swphy2: ethernet-phy@18 {
reg = <18>;
};
- swphy3: swphy3@19 {
+ swphy3: ethernet-phy@19 {
reg = <19>;
};
- swphy4: swphy4@20 {
+ swphy4: ethernet-phy@20 {
reg = <20>;
};
};
diff --git a/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts b/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts
index 4125202028c8..67892f0d2863 100644
--- a/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts
+++ b/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts
@@ -497,42 +497,42 @@ ge_phy: ethernet-phy@0 {
reset-deassert-us = <10000>;
};
- switch0: switch0@4 {
+ switch0: ethernet-switch@4 {
compatible = "marvell,mv88e6085";
reg = <4>;
pinctrl-names = "default";
pinctrl-0 = <&cp1_switch_reset_pins>;
reset-gpios = <&cp1_gpio1 24 GPIO_ACTIVE_LOW>;
- ports {
+ ethernet-ports {
#address-cells = <1>;
#size-cells = <0>;
- port@1 {
+ ethernet-port@1 {
reg = <1>;
label = "lan2";
phy-handle = <&switch0phy0>;
};
- port@2 {
+ ethernet-port@2 {
reg = <2>;
label = "lan1";
phy-handle = <&switch0phy1>;
};
- port@3 {
+ ethernet-port@3 {
reg = <3>;
label = "lan4";
phy-handle = <&switch0phy2>;
};
- port@4 {
+ ethernet-port@4 {
reg = <4>;
label = "lan3";
phy-handle = <&switch0phy3>;
};
- port@5 {
+ ethernet-port@5 {
reg = <5>;
label = "cpu";
ethernet = <&cp1_eth2>;
@@ -545,19 +545,19 @@ mdio {
#address-cells = <1>;
#size-cells = <0>;
- switch0phy0: switch0phy0@11 {
+ switch0phy0: ethernet-phy@11 {
reg = <0x11>;
};
- switch0phy1: switch0phy1@12 {
+ switch0phy1: ethernet-phy@12 {
reg = <0x12>;
};
- switch0phy2: switch0phy2@13 {
+ switch0phy2: ethernet-phy@13 {
reg = <0x13>;
};
- switch0phy3: switch0phy3@14 {
+ switch0phy3: ethernet-phy@14 {
reg = <0x14>;
};
};
diff --git a/arch/arm64/boot/dts/marvell/cn9130-crb.dtsi b/arch/arm64/boot/dts/marvell/cn9130-crb.dtsi
index 32cfb3e2efc3..7538ed56053b 100644
--- a/arch/arm64/boot/dts/marvell/cn9130-crb.dtsi
+++ b/arch/arm64/boot/dts/marvell/cn9130-crb.dtsi
@@ -207,11 +207,9 @@ phy0: ethernet-phy@0 {
reg = <0>;
};
- switch6: switch0@6 {
+ switch6: ethernet-switch@6 {
/* Actual device is MV88E6393X */
compatible = "marvell,mv88e6190";
- #address-cells = <1>;
- #size-cells = <0>;
reg = <6>;
interrupt-parent = <&cp0_gpio1>;
interrupts = <28 IRQ_TYPE_LEVEL_LOW>;
@@ -220,59 +218,59 @@ switch6: switch0@6 {
dsa,member = <0 0>;
- ports {
+ ethernet-ports {
#address-cells = <1>;
#size-cells = <0>;
- port@1 {
+ ethernet-port@1 {
reg = <1>;
label = "p1";
phy-handle = <&switch0phy1>;
};
- port@2 {
+ ethernet-port@2 {
reg = <2>;
label = "p2";
phy-handle = <&switch0phy2>;
};
- port@3 {
+ ethernet-port@3 {
reg = <3>;
label = "p3";
phy-handle = <&switch0phy3>;
};
- port@4 {
+ ethernet-port@4 {
reg = <4>;
label = "p4";
phy-handle = <&switch0phy4>;
};
- port@5 {
+ ethernet-port@5 {
reg = <5>;
label = "p5";
phy-handle = <&switch0phy5>;
};
- port@6 {
+ ethernet-port@6 {
reg = <6>;
label = "p6";
phy-handle = <&switch0phy6>;
};
- port@7 {
+ ethernet-port@7 {
reg = <7>;
label = "p7";
phy-handle = <&switch0phy7>;
};
- port@8 {
+ ethernet-port@8 {
reg = <8>;
label = "p8";
phy-handle = <&switch0phy8>;
};
- port@9 {
+ ethernet-port@9 {
reg = <9>;
label = "p9";
phy-mode = "10gbase-r";
@@ -280,7 +278,7 @@ port@9 {
managed = "in-band-status";
};
- port@a {
+ ethernet-port@a {
reg = <10>;
ethernet = <&cp0_eth0>;
phy-mode = "10gbase-r";
@@ -293,35 +291,35 @@ mdio {
#address-cells = <1>;
#size-cells = <0>;
- switch0phy1: switch0phy1@1 {
+ switch0phy1: ethernet-phy@1 {
reg = <0x1>;
};
- switch0phy2: switch0phy2@2 {
+ switch0phy2: ethernet-phy@2 {
reg = <0x2>;
};
- switch0phy3: switch0phy3@3 {
+ switch0phy3: ethernet-phy@3 {
reg = <0x3>;
};
- switch0phy4: switch0phy4@4 {
+ switch0phy4: ethernet-phy@4 {
reg = <0x4>;
};
- switch0phy5: switch0phy5@5 {
+ switch0phy5: ethernet-phy@5 {
reg = <0x5>;
};
- switch0phy6: switch0phy6@6 {
+ switch0phy6: ethernet-phy@6 {
reg = <0x6>;
};
- switch0phy7: switch0phy7@7 {
+ switch0phy7: ethernet-phy@7 {
reg = <0x7>;
};
- switch0phy8: switch0phy8@8 {
+ switch0phy8: ethernet-phy@8 {
reg = <0x8>;
};
};
--
2.34.1
^ permalink raw reply related [flat|nested] 13+ messages in thread
* [PATCH net-next v5 6/7] dt-bindings: marvell: Rewrite MV88E6xxx in schema
2023-10-23 7:18 [PATCH net-next v5 0/7] Create a binding for the Marvell MV88E6xxx DSA switches Linus Walleij
` (4 preceding siblings ...)
2023-10-23 7:18 ` [PATCH net-next v5 5/7] ARM64: dts: marvell: " Linus Walleij
@ 2023-10-23 7:18 ` Linus Walleij
2023-10-23 19:51 ` Rob Herring
2023-10-23 7:18 ` [PATCH net-next v5 7/7] dt-bindings: marvell: Add Marvell MV88E6060 DSA schema Linus Walleij
6 siblings, 1 reply; 13+ messages in thread
From: Linus Walleij @ 2023-10-23 7:18 UTC (permalink / raw)
To: Andrew Lunn, Gregory Clement, Sebastian Hesselbarth, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Russell King,
Florian Fainelli, Vladimir Oltean, David S. Miller, Eric Dumazet,
Jakub Kicinski, Paolo Abeni
Cc: Christian Marangi, linux-arm-kernel, devicetree, linux-kernel,
netdev, Linus Walleij
This is an attempt to rewrite the Marvell MV88E6xxx switch bindings
in YAML schema.
The current text binding says:
WARNING: This binding is currently unstable. Do not program it into a
FLASH never to be changed again. Once this binding is stable, this
warning will be removed.
Well that never happened before we switched to YAML markup,
we can't have it like this, what about fixing the mess?
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
.../bindings/net/dsa/marvell,mv88e6xxx.yaml | 330 +++++++++++++++++++++
.../devicetree/bindings/net/dsa/marvell.txt | 109 -------
MAINTAINERS | 2 +-
3 files changed, 331 insertions(+), 110 deletions(-)
diff --git a/Documentation/devicetree/bindings/net/dsa/marvell,mv88e6xxx.yaml b/Documentation/devicetree/bindings/net/dsa/marvell,mv88e6xxx.yaml
new file mode 100644
index 000000000000..34d8561a2187
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/dsa/marvell,mv88e6xxx.yaml
@@ -0,0 +1,330 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/dsa/marvell,mv88e6xxx.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Marvell MV88E6xxx DSA switch family
+
+maintainers:
+ - Andrew Lunn <andrew@lunn.ch>
+
+description:
+ The Marvell MV88E6xxx switch series has been produced and sold
+ by Marvell since at least 2008. The switch has a few compatibles which
+ just indicate the base address of the switch, then operating systems
+ can investigate switch ID registers to find out which actual version
+ of the switch it is dealing with.
+
+properties:
+ compatible:
+ enum:
+ - marvell,mv88e6085
+ - marvell,mv88e6190
+ - marvell,mv88e6250
+ description: |
+ marvell,mv88e6085: This switch uses base address 0x10.
+ This switch and its siblings will be autodetected from
+ ID registers found in the switch, so only "marvell,mv88e6085" should be
+ specified. This includes the following list of MV88Exxxx switches:
+ 6085, 6095, 6097, 6123, 6131, 6141, 6161, 6165, 6171, 6172, 6175, 6176,
+ 6185, 6240, 6320, 6321, 6341, 6350, 6351, 6352
+ marvell,mv88e6190: This switch uses base address 0x00.
+ This switch and its siblings will be autodetected from
+ ID registers found in the switch, so only "marvell,mv88e6190" should be
+ specified. This includes the following list of MV88Exxxx switches:
+ 6190, 6190X, 6191, 6290, 6361, 6390, 6390X
+ marvell,mv88e6250: This switch uses base address 0x08 or 0x18.
+ This switch and its siblings will be autodetected from
+ ID registers found in the switch, so only "marvell,mv88e6250" should be
+ specified. This includes the following list of MV88Exxxx switches:
+ 6220, 6250
+
+ reg:
+ maxItems: 1
+
+ eeprom-length:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: Set to the length of an EEPROM connected to the switch. Must be
+ set if the switch can not detect the presence and/or size of a connected
+ EEPROM, otherwise optional.
+
+ reset-gpios:
+ description:
+ GPIO to be used to reset the whole device
+ maxItems: 1
+
+ interrupts:
+ description: The switch provides an external interrupt line, but it is
+ not always used by target systems.
+ maxItems: 1
+
+ interrupt-controller:
+ description: The switch has an internal interrupt controller used by
+ the different sub-blocks.
+
+ '#interrupt-cells':
+ description: The internal interrupt controller only supports triggering
+ on active high level interrupts so the second cell must alway be set to
+ IRQ_TYPE_LEVEL_HIGH.
+ const: 2
+
+ mdio:
+ $ref: /schemas/net/mdio.yaml#
+ unevaluatedProperties: false
+ description: Marvell MV88E6xxx switches have an varying combination of
+ internal and external MDIO buses, in some cases a combined bus that
+ can be used both internally and externally. This node is for the
+ primary bus, used internally and sometimes also externally.
+
+ mdio-external:
+ $ref: /schemas/net/mdio.yaml#
+ unevaluatedProperties: false
+ description: Marvell MV88E6xxx switches that have a separate external
+ MDIO bus use this port to access external components on the MDIO bus.
+
+ properties:
+ compatible:
+ const: marvell,mv88e6xxx-mdio-external
+
+ required:
+ - compatible
+
+allOf:
+ - $ref: dsa.yaml#/$defs/ethernet-ports
+
+required:
+ - compatible
+ - reg
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/gpio/gpio.h>
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethernet-switch@0 {
+ compatible = "marvell,mv88e6085";
+ reg = <0>;
+ reset-gpios = <&gpio5 1 GPIO_ACTIVE_LOW>;
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ sw_phy0: ethernet-phy@0 {
+ reg = <0x0>;
+ };
+
+ sw_phy1: ethernet-phy@1 {
+ reg = <0x1>;
+ };
+
+ sw_phy2: ethernet-phy@2 {
+ reg = <0x2>;
+ };
+
+ sw_phy3: ethernet-phy@3 {
+ reg = <0x3>;
+ };
+ };
+
+ ethernet-ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethernet-port@0 {
+ reg = <0>;
+ label = "lan4";
+ phy-handle = <&sw_phy0>;
+ phy-mode = "internal";
+ };
+
+ ethernet-port@1 {
+ reg = <1>;
+ label = "lan3";
+ phy-handle = <&sw_phy1>;
+ phy-mode = "internal";
+ };
+
+ ethernet-port@2 {
+ reg = <2>;
+ label = "lan2";
+ phy-handle = <&sw_phy2>;
+ phy-mode = "internal";
+ };
+
+ ethernet-port@3 {
+ reg = <3>;
+ label = "lan1";
+ phy-handle = <&sw_phy3>;
+ phy-mode = "internal";
+ };
+
+ ethernet-port@5 {
+ reg = <5>;
+ ethernet = <&fec>;
+ phy-mode = "rgmii-id";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+ };
+ };
+ };
+ - |
+ #include <dt-bindings/interrupt-controller/irq.h>
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethernet-switch@0 {
+ compatible = "marvell,mv88e6190";
+ #interrupt-cells = <2>;
+ interrupt-controller;
+ interrupt-parent = <&gpio1>;
+ interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-0 = <&switch_interrupt_pins>;
+ pinctrl-names = "default";
+ reg = <0>;
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ switch0phy1: ethernet-phy@1 {
+ reg = <0x1>;
+ };
+
+ switch0phy2: ethernet-phy@2 {
+ reg = <0x2>;
+ };
+
+ switch0phy3: ethernet-phy@3 {
+ reg = <0x3>;
+ };
+
+ switch0phy4: ethernet-phy@4 {
+ reg = <0x4>;
+ };
+
+ switch0phy5: ethernet-phy@5 {
+ reg = <0x5>;
+ };
+
+ switch0phy6: ethernet-phy@6 {
+ reg = <0x6>;
+ };
+
+ switch0phy7: ethernet-phy@7 {
+ reg = <0x7>;
+ };
+
+ switch0phy8: ethernet-phy@8 {
+ reg = <0x8>;
+ };
+ };
+
+ mdio-external {
+ compatible = "marvell,mv88e6xxx-mdio-external";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ phy1: ethernet-phy@b {
+ reg = <0xb>;
+ compatible = "ethernet-phy-ieee802.3-c45";
+ };
+
+ phy2: ethernet-phy@c {
+ reg = <0xc>;
+ compatible = "ethernet-phy-ieee802.3-c45";
+ };
+ };
+
+ ethernet-ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethernet-port@0 {
+ ethernet = <ð0>;
+ phy-mode = "rgmii";
+ reg = <0>;
+
+ fixed-link {
+ full-duplex;
+ pause;
+ speed = <1000>;
+ };
+ };
+
+ ethernet-port@1 {
+ label = "lan1";
+ phy-handle = <&switch0phy1>;
+ reg = <1>;
+ };
+
+ ethernet-port@2 {
+ label = "lan2";
+ phy-handle = <&switch0phy2>;
+ reg = <2>;
+ };
+
+ ethernet-port@3 {
+ label = "lan3";
+ phy-handle = <&switch0phy3>;
+ reg = <3>;
+ };
+
+ ethernet-port@4 {
+ label = "lan4";
+ phy-handle = <&switch0phy4>;
+ reg = <4>;
+ };
+
+ ethernet-port@5 {
+ label = "lan5";
+ phy-handle = <&switch0phy5>;
+ reg = <5>;
+ };
+
+ ethernet-port@6 {
+ label = "lan6";
+ phy-handle = <&switch0phy6>;
+ reg = <6>;
+ };
+
+ ethernet-port@7 {
+ label = "lan7";
+ phy-handle = <&switch0phy7>;
+ reg = <7>;
+ };
+
+ ethernet-port@8 {
+ label = "lan8";
+ phy-handle = <&switch0phy8>;
+ reg = <8>;
+ };
+
+ ethernet-port@9 {
+ /* 88X3310P external phy */
+ label = "lan9";
+ phy-handle = <&phy1>;
+ phy-mode = "xaui";
+ reg = <9>;
+ };
+
+ ethernet-port@a {
+ /* 88X3310P external phy */
+ label = "lan10";
+ phy-handle = <&phy2>;
+ phy-mode = "xaui";
+ reg = <0xa>;
+ };
+ };
+ };
+ };
diff --git a/Documentation/devicetree/bindings/net/dsa/marvell.txt b/Documentation/devicetree/bindings/net/dsa/marvell.txt
deleted file mode 100644
index 6ec0c181b6db..000000000000
--- a/Documentation/devicetree/bindings/net/dsa/marvell.txt
+++ /dev/null
@@ -1,109 +0,0 @@
-Marvell DSA Switch Device Tree Bindings
----------------------------------------
-
-WARNING: This binding is currently unstable. Do not program it into a
-FLASH never to be changed again. Once this binding is stable, this
-warning will be removed.
-
-If you need a stable binding, use the old dsa.txt binding.
-
-Marvell Switches are MDIO devices. The following properties should be
-placed as a child node of an mdio device.
-
-The properties described here are those specific to Marvell devices.
-Additional required and optional properties can be found in dsa.txt.
-
-The compatibility string is used only to find an identification register,
-which is at a different MDIO base address in different switch families.
-- "marvell,mv88e6085" : Switch has base address 0x10. Use with models:
- 6085, 6095, 6097, 6123, 6131, 6141, 6161, 6165,
- 6171, 6172, 6175, 6176, 6185, 6240, 6320, 6321,
- 6341, 6350, 6351, 6352
-- "marvell,mv88e6190" : Switch has base address 0x00. Use with models:
- 6190, 6190X, 6191, 6290, 6361, 6390, 6390X
-- "marvell,mv88e6250" : Switch has base address 0x08 or 0x18. Use with model:
- 6220, 6250
-
-Required properties:
-- compatible : Should be one of "marvell,mv88e6085",
- "marvell,mv88e6190" or "marvell,mv88e6250" as
- indicated above
-- reg : Address on the MII bus for the switch.
-
-Optional properties:
-
-- reset-gpios : Should be a gpio specifier for a reset line
-- interrupts : Interrupt from the switch
-- interrupt-controller : Indicates the switch is itself an interrupt
- controller. This is used for the PHY interrupts.
-#interrupt-cells = <2> : Controller uses two cells, number and flag
-- eeprom-length : Set to the length of an EEPROM connected to the
- switch. Must be set if the switch can not detect
- the presence and/or size of a connected EEPROM,
- otherwise optional.
-- mdio : Container of PHY and devices on the switches MDIO
- bus.
-- mdio? : Container of PHYs and devices on the external MDIO
- bus. The node must contains a compatible string of
- "marvell,mv88e6xxx-mdio-external"
-
-Example:
-
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
- interrupt-parent = <&gpio0>;
- interrupts = <27 IRQ_TYPE_LEVEL_LOW>;
- interrupt-controller;
- #interrupt-cells = <2>;
-
- switch0: switch@0 {
- compatible = "marvell,mv88e6085";
- reg = <0>;
- reset-gpios = <&gpio5 1 GPIO_ACTIVE_LOW>;
-
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
- switch1phy0: switch1phy0@0 {
- reg = <0>;
- interrupt-parent = <&switch0>;
- interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
- };
- };
- };
- };
-
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
- interrupt-parent = <&gpio0>;
- interrupts = <27 IRQ_TYPE_LEVEL_LOW>;
- interrupt-controller;
- #interrupt-cells = <2>;
-
- switch0: switch@0 {
- compatible = "marvell,mv88e6190";
- reg = <0>;
- reset-gpios = <&gpio5 1 GPIO_ACTIVE_LOW>;
-
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
- switch1phy0: switch1phy0@0 {
- reg = <0>;
- interrupt-parent = <&switch0>;
- interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
- };
- };
-
- mdio1 {
- compatible = "marvell,mv88e6xxx-mdio-external";
- #address-cells = <1>;
- #size-cells = <0>;
- switch1phy9: switch1phy0@9 {
- reg = <9>;
- };
- };
- };
- };
diff --git a/MAINTAINERS b/MAINTAINERS
index 90f13281d297..1b4475254d27 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -12625,7 +12625,7 @@ MARVELL 88E6XXX ETHERNET SWITCH FABRIC DRIVER
M: Andrew Lunn <andrew@lunn.ch>
L: netdev@vger.kernel.org
S: Maintained
-F: Documentation/devicetree/bindings/net/dsa/marvell.txt
+F: Documentation/devicetree/bindings/net/dsa/marvell,mv88e6xxx.yaml
F: Documentation/networking/devlink/mv88e6xxx.rst
F: drivers/net/dsa/mv88e6xxx/
F: include/linux/dsa/mv88e6xxx.h
--
2.34.1
^ permalink raw reply related [flat|nested] 13+ messages in thread
* [PATCH net-next v5 7/7] dt-bindings: marvell: Add Marvell MV88E6060 DSA schema
2023-10-23 7:18 [PATCH net-next v5 0/7] Create a binding for the Marvell MV88E6xxx DSA switches Linus Walleij
` (5 preceding siblings ...)
2023-10-23 7:18 ` [PATCH net-next v5 6/7] dt-bindings: marvell: Rewrite MV88E6xxx in schema Linus Walleij
@ 2023-10-23 7:18 ` Linus Walleij
6 siblings, 0 replies; 13+ messages in thread
From: Linus Walleij @ 2023-10-23 7:18 UTC (permalink / raw)
To: Andrew Lunn, Gregory Clement, Sebastian Hesselbarth, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Russell King,
Florian Fainelli, Vladimir Oltean, David S. Miller, Eric Dumazet,
Jakub Kicinski, Paolo Abeni
Cc: Christian Marangi, linux-arm-kernel, devicetree, linux-kernel,
netdev, Linus Walleij, Vladimir Oltean
The Marvell MV88E6060 is one of the oldest DSA switches from
Marvell, and it has DT bindings used in the wild. Let's define
them properly.
It is different enough from the rest of the MV88E6xxx switches
that it deserves its own binding.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
.../bindings/net/dsa/marvell,mv88e6060.yaml | 88 ++++++++++++++++++++++
MAINTAINERS | 1 +
2 files changed, 89 insertions(+)
diff --git a/Documentation/devicetree/bindings/net/dsa/marvell,mv88e6060.yaml b/Documentation/devicetree/bindings/net/dsa/marvell,mv88e6060.yaml
new file mode 100644
index 000000000000..4f1adf00431a
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/dsa/marvell,mv88e6060.yaml
@@ -0,0 +1,88 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/dsa/marvell,mv88e6060.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Marvell MV88E6060 DSA switch
+
+maintainers:
+ - Andrew Lunn <andrew@lunn.ch>
+
+description:
+ The Marvell MV88E6060 switch has been produced and sold by Marvell
+ since at least 2008. The switch has one pin ADDR4 that controls the
+ MDIO address of the switch to be 0x10 or 0x00, and on the MDIO bus
+ connected to the switch, the PHYs inside the switch appear as
+ independent devices on address 0x00-0x04 or 0x10-0x14, so in difference
+ from many other DSA switches this switch does not have an internal
+ MDIO bus for the PHY devices.
+
+properties:
+ compatible:
+ const: marvell,mv88e6060
+ description:
+ The MV88E6060 is the oldest Marvell DSA switch product, and
+ as such a bit limited in features compared to later hardware.
+
+ reg:
+ maxItems: 1
+
+ reset-gpios:
+ description:
+ GPIO to be used to reset the whole device
+ maxItems: 1
+
+allOf:
+ - $ref: dsa.yaml#/$defs/ethernet-ports
+
+required:
+ - compatible
+ - reg
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/gpio/gpio.h>
+ #include <dt-bindings/interrupt-controller/irq.h>
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethernet-switch@16 {
+ compatible = "marvell,mv88e6060";
+ reg = <16>;
+
+ ethernet-ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethernet-port@0 {
+ reg = <0>;
+ label = "lan1";
+ };
+ ethernet-port@1 {
+ reg = <1>;
+ label = "lan2";
+ };
+ ethernet-port@2 {
+ reg = <2>;
+ label = "lan3";
+ };
+ ethernet-port@3 {
+ reg = <3>;
+ label = "lan4";
+ };
+ ethernet-port@5 {
+ reg = <5>;
+ phy-mode = "rev-mii";
+ ethernet = <ðc>;
+ fixed-link {
+ speed = <100>;
+ full-duplex;
+ };
+ };
+ };
+ };
+ };
diff --git a/MAINTAINERS b/MAINTAINERS
index 1b4475254d27..4c933a2a56ad 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -12625,6 +12625,7 @@ MARVELL 88E6XXX ETHERNET SWITCH FABRIC DRIVER
M: Andrew Lunn <andrew@lunn.ch>
L: netdev@vger.kernel.org
S: Maintained
+F: Documentation/devicetree/bindings/net/dsa/marvell,mv88e6060.yaml
F: Documentation/devicetree/bindings/net/dsa/marvell,mv88e6xxx.yaml
F: Documentation/networking/devlink/mv88e6xxx.rst
F: drivers/net/dsa/mv88e6xxx/
--
2.34.1
^ permalink raw reply related [flat|nested] 13+ messages in thread
* Re: [PATCH net-next v5 1/7] dt-bindings: net: dsa: Require ports or ethernet-ports
2023-10-23 7:18 ` [PATCH net-next v5 1/7] dt-bindings: net: dsa: Require ports or ethernet-ports Linus Walleij
@ 2023-10-23 7:51 ` Linus Walleij
2023-10-23 17:43 ` Rob Herring
2023-10-23 17:40 ` Rob Herring
1 sibling, 1 reply; 13+ messages in thread
From: Linus Walleij @ 2023-10-23 7:51 UTC (permalink / raw)
To: Andrew Lunn, Gregory Clement, Sebastian Hesselbarth, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Russell King,
Florian Fainelli, Vladimir Oltean, David S. Miller, Eric Dumazet,
Jakub Kicinski, Paolo Abeni
Cc: Christian Marangi, linux-arm-kernel, devicetree, linux-kernel,
netdev, Rob Herring
On Mon, Oct 23, 2023 at 9:19 AM Linus Walleij <linus.walleij@linaro.org> wrote:
> Bindings using dsa.yaml#/$defs/ethernet-ports specify that
> a DSA switch node need to have a ports or ethernet-ports
> subnode, and that is actually required, so add requirements
> using oneOf.
>
> Suggested-by: Rob Herring <robh@kernel.org>
> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
(...)
> + oneOf:
> + - required:
> + - ports
> + - required:
> + - ethernet-ports
Ooops I meant to drop the patch altogether because I just
couldn't figure out how to test this.
Ignore bot complaints on this one then.
Yours,
Linus Walleij
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [PATCH net-next v5 1/7] dt-bindings: net: dsa: Require ports or ethernet-ports
2023-10-23 7:18 ` [PATCH net-next v5 1/7] dt-bindings: net: dsa: Require ports or ethernet-ports Linus Walleij
2023-10-23 7:51 ` Linus Walleij
@ 2023-10-23 17:40 ` Rob Herring
1 sibling, 0 replies; 13+ messages in thread
From: Rob Herring @ 2023-10-23 17:40 UTC (permalink / raw)
To: Linus Walleij
Cc: Andrew Lunn, Gregory Clement, Rob Herring, linux-kernel,
devicetree, Conor Dooley, Krzysztof Kozlowski, linux-arm-kernel,
Vladimir Oltean, Russell King, Eric Dumazet, Jakub Kicinski,
Florian Fainelli, Sebastian Hesselbarth, Christian Marangi,
Paolo Abeni, netdev, David S. Miller
On Mon, 23 Oct 2023 09:18:52 +0200, Linus Walleij wrote:
> Bindings using dsa.yaml#/$defs/ethernet-ports specify that
> a DSA switch node need to have a ports or ethernet-ports
> subnode, and that is actually required, so add requirements
> using oneOf.
>
> Suggested-by: Rob Herring <robh@kernel.org>
> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
> ---
> Documentation/devicetree/bindings/net/dsa/dsa.yaml | 6 ++++++
> 1 file changed, 6 insertions(+)
>
My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check'
on your patch (DT_CHECKER_FLAGS is new in v5.13):
yamllint warnings/errors:
./Documentation/devicetree/bindings/net/dsa/dsa.yaml:60:7: [warning] wrong indentation: expected 8 but found 6 (indentation)
./Documentation/devicetree/bindings/net/dsa/dsa.yaml:62:7: [warning] wrong indentation: expected 8 but found 6 (indentation)
dtschema/dtc warnings/errors:
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/net/dsa/dsa.yaml: $defs: 'oneOf' should not be valid under {'$ref': '#/definitions/json-schema-prop-names'}
hint: A json-schema keyword was found in $defs key.
from schema $id: http://devicetree.org/meta-schemas/keywords.yaml#
/builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/net/dsa/dsa.yaml: $defs:oneOf: [{'required': ['ports']}, {'required': ['ethernet-ports']}] is not of type 'object'
hint: $defs entries must contain schemas
from schema $id: http://devicetree.org/meta-schemas/keywords.yaml#
doc reference errors (make refcheckdocs):
See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20231023-marvell-88e6152-wan-led-v5-1-0e82952015a7@linaro.org
The base for the series is generally the latest rc1. A different dependency
should be noted in *this* patch.
If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:
pip3 install dtschema --upgrade
Please check and re-submit after running the above command yourself. Note
that DT_SCHEMA_FILES can be set to your schema file to speed up checking
your schema. However, it must be unset to test all examples with your schema.
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [PATCH net-next v5 1/7] dt-bindings: net: dsa: Require ports or ethernet-ports
2023-10-23 7:51 ` Linus Walleij
@ 2023-10-23 17:43 ` Rob Herring
0 siblings, 0 replies; 13+ messages in thread
From: Rob Herring @ 2023-10-23 17:43 UTC (permalink / raw)
To: Linus Walleij
Cc: Andrew Lunn, Gregory Clement, Sebastian Hesselbarth,
Krzysztof Kozlowski, Conor Dooley, Russell King,
Florian Fainelli, Vladimir Oltean, David S. Miller, Eric Dumazet,
Jakub Kicinski, Paolo Abeni, Christian Marangi, linux-arm-kernel,
devicetree, linux-kernel, netdev
On Mon, Oct 23, 2023 at 09:51:00AM +0200, Linus Walleij wrote:
> On Mon, Oct 23, 2023 at 9:19 AM Linus Walleij <linus.walleij@linaro.org> wrote:
>
> > Bindings using dsa.yaml#/$defs/ethernet-ports specify that
> > a DSA switch node need to have a ports or ethernet-ports
> > subnode, and that is actually required, so add requirements
> > using oneOf.
> >
> > Suggested-by: Rob Herring <robh@kernel.org>
> > Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
> (...)
> > + oneOf:
> > + - required:
> > + - ports
> > + - required:
> > + - ethernet-ports
>
> Ooops I meant to drop the patch altogether because I just
> couldn't figure out how to test this.
Just move it up a level (no indent).
Rob
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [PATCH net-next v5 2/7] dt-bindings: net: mvusb: Fix up DSA example
2023-10-23 7:18 ` [PATCH net-next v5 2/7] dt-bindings: net: mvusb: Fix up DSA example Linus Walleij
@ 2023-10-23 19:49 ` Rob Herring
0 siblings, 0 replies; 13+ messages in thread
From: Rob Herring @ 2023-10-23 19:49 UTC (permalink / raw)
To: Linus Walleij
Cc: netdev, Krzysztof Kozlowski, Vladimir Oltean, Christian Marangi,
Eric Dumazet, Florian Fainelli, devicetree,
Sebastian Hesselbarth, Rob Herring, Conor Dooley, linux-kernel,
Russell King, Jakub Kicinski, David S. Miller, linux-arm-kernel,
Andrew Lunn, Gregory Clement, Vladimir Oltean, Paolo Abeni
On Mon, 23 Oct 2023 09:18:53 +0200, Linus Walleij wrote:
> When adding a proper schema for the Marvell mx88e6xxx switch,
> the scripts start complaining about this embedded example:
>
> dtschema/dtc warnings/errors:
> net/marvell,mvusb.example.dtb: switch@0: ports: '#address-cells'
> is a required property
> from schema $id: http://devicetree.org/schemas/net/dsa/marvell,mv88e6xxx.yaml#
> net/marvell,mvusb.example.dtb: switch@0: ports: '#size-cells'
> is a required property
> from schema $id: http://devicetree.org/schemas/net/dsa/marvell,mv88e6xxx.yaml#
>
> Fix this up by extending the example with those properties in
> the ports node.
>
> While we are at it, rename "ports" to "ethernet-ports" and rename
> "switch" to "ethernet-switch" as this is recommended practice.
>
> Reviewed-by: Andrew Lunn <andrew@lunn.ch>
> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
> ---
> Documentation/devicetree/bindings/net/marvell,mvusb.yaml | 7 +++++--
> 1 file changed, 5 insertions(+), 2 deletions(-)
>
Reviewed-by: Rob Herring <robh@kernel.org>
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [PATCH net-next v5 6/7] dt-bindings: marvell: Rewrite MV88E6xxx in schema
2023-10-23 7:18 ` [PATCH net-next v5 6/7] dt-bindings: marvell: Rewrite MV88E6xxx in schema Linus Walleij
@ 2023-10-23 19:51 ` Rob Herring
0 siblings, 0 replies; 13+ messages in thread
From: Rob Herring @ 2023-10-23 19:51 UTC (permalink / raw)
To: Linus Walleij
Cc: Vladimir Oltean, David S. Miller, devicetree, Conor Dooley,
Paolo Abeni, Sebastian Hesselbarth, Christian Marangi,
Gregory Clement, Jakub Kicinski, Andrew Lunn, linux-kernel,
Krzysztof Kozlowski, Eric Dumazet, linux-arm-kernel, netdev,
Florian Fainelli, Rob Herring, Russell King
On Mon, 23 Oct 2023 09:18:57 +0200, Linus Walleij wrote:
> This is an attempt to rewrite the Marvell MV88E6xxx switch bindings
> in YAML schema.
>
> The current text binding says:
> WARNING: This binding is currently unstable. Do not program it into a
> FLASH never to be changed again. Once this binding is stable, this
> warning will be removed.
>
> Well that never happened before we switched to YAML markup,
> we can't have it like this, what about fixing the mess?
>
> Reviewed-by: Andrew Lunn <andrew@lunn.ch>
> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
> ---
> .../bindings/net/dsa/marvell,mv88e6xxx.yaml | 330 +++++++++++++++++++++
> .../devicetree/bindings/net/dsa/marvell.txt | 109 -------
> MAINTAINERS | 2 +-
> 3 files changed, 331 insertions(+), 110 deletions(-)
>
Reviewed-by: Rob Herring <robh@kernel.org>
^ permalink raw reply [flat|nested] 13+ messages in thread
end of thread, other threads:[~2023-10-23 19:51 UTC | newest]
Thread overview: 13+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2023-10-23 7:18 [PATCH net-next v5 0/7] Create a binding for the Marvell MV88E6xxx DSA switches Linus Walleij
2023-10-23 7:18 ` [PATCH net-next v5 1/7] dt-bindings: net: dsa: Require ports or ethernet-ports Linus Walleij
2023-10-23 7:51 ` Linus Walleij
2023-10-23 17:43 ` Rob Herring
2023-10-23 17:40 ` Rob Herring
2023-10-23 7:18 ` [PATCH net-next v5 2/7] dt-bindings: net: mvusb: Fix up DSA example Linus Walleij
2023-10-23 19:49 ` Rob Herring
2023-10-23 7:18 ` [PATCH net-next v5 3/7] ARM: dts: marvell: Fix some common switch mistakes Linus Walleij
2023-10-23 7:18 ` [PATCH net-next v5 4/7] ARM: dts: nxp: " Linus Walleij
2023-10-23 7:18 ` [PATCH net-next v5 5/7] ARM64: dts: marvell: " Linus Walleij
2023-10-23 7:18 ` [PATCH net-next v5 6/7] dt-bindings: marvell: Rewrite MV88E6xxx in schema Linus Walleij
2023-10-23 19:51 ` Rob Herring
2023-10-23 7:18 ` [PATCH net-next v5 7/7] dt-bindings: marvell: Add Marvell MV88E6060 DSA schema Linus Walleij
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).