From: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
To: patrick@stwcx.xyz, Rob Herring <robh+dt@kernel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
Conor Dooley <conor+dt@kernel.org>, Joel Stanley <joel@jms.id.au>,
Andrew Jeffery <andrew@codeconstruct.com.au>
Cc: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>,
devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
linux-aspeed@lists.ozlabs.org, linux-kernel@vger.kernel.org
Subject: [PATCH v2 01/14] ARM: dts: aspeed: yosemite4: Revise i2c-mux devices
Date: Mon, 11 Dec 2023 10:49:32 +0800 [thread overview]
Message-ID: <20231211024947.3990898-2-Delphine_CC_Chiu@wiwynn.com> (raw)
In-Reply-To: <20231211024947.3990898-1-Delphine_CC_Chiu@wiwynn.com>
Revise Yosemite 4 devicetree for devices behind i2c-mux
- Add gpio and eeprom behind i2c-mux
- Remove redundant idle-state setting for i2c-mux
Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
---
.../aspeed/aspeed-bmc-facebook-yosemite4.dts | 381 ++++++++++++++++--
1 file changed, 347 insertions(+), 34 deletions(-)
diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
index 64075cc41d92..a5b4585e81e6 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-facebook-yosemite4.dts
@@ -17,6 +17,25 @@ aliases {
serial6 = &uart7;
serial7 = &uart8;
serial8 = &uart9;
+
+ i2c16 = &imux16;
+ i2c17 = &imux17;
+ i2c18 = &imux18;
+ i2c19 = &imux19;
+ i2c20 = &imux20;
+ i2c21 = &imux21;
+ i2c22 = &imux22;
+ i2c23 = &imux23;
+ i2c24 = &imux24;
+ i2c25 = &imux25;
+ i2c26 = &imux26;
+ i2c27 = &imux27;
+ i2c28 = &imux28;
+ i2c29 = &imux29;
+ i2c30 = &imux30;
+ i2c31 = &imux31;
+ i2c32 = &imux32;
+ i2c33 = &imux33;
};
chosen {
@@ -259,9 +278,109 @@ &i2c8 {
bus-frequency = <400000>;
i2c-mux@70 {
compatible = "nxp,pca9544";
- idle-state = <0>;
i2c-mux-idle-disconnect;
reg = <0x70>;
+
+ imux16: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+
+ gpio@49 {
+ compatible = "nxp,pca9537";
+ reg = <0x49>;
+ };
+
+ eeprom@50 {
+ compatible = "atmel,24c128";
+ reg = <0x50>;
+ };
+
+ eeprom@51 {
+ compatible = "atmel,24c128";
+ reg = <0x51>;
+ };
+
+ eeprom@54 {
+ compatible = "atmel,24c128";
+ reg = <0x54>;
+ };
+ };
+
+ imux17: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ gpio@49 {
+ compatible = "nxp,pca9537";
+ reg = <0x49>;
+ };
+
+ eeprom@50 {
+ compatible = "atmel,24c128";
+ reg = <0x50>;
+ };
+
+ eeprom@51 {
+ compatible = "atmel,24c128";
+ reg = <0x51>;
+ };
+
+ eeprom@54 {
+ compatible = "atmel,24c128";
+ reg = <0x54>;
+ };
+ };
+
+ imux18: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ gpio@49 {
+ compatible = "nxp,pca9537";
+ reg = <0x49>;
+ };
+
+ eeprom@50 {
+ compatible = "atmel,24c128";
+ reg = <0x50>;
+ };
+
+ eeprom@51 {
+ compatible = "atmel,24c128";
+ reg = <0x51>;
+ };
+
+ eeprom@54 {
+ compatible = "atmel,24c128";
+ reg = <0x54>;
+ };
+ };
+
+ imux19: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ gpio@49 {
+ compatible = "nxp,pca9537";
+ reg = <0x49>;
+ };
+
+ eeprom@50 {
+ compatible = "atmel,24c128";
+ reg = <0x50>;
+ };
+
+ eeprom@51 {
+ compatible = "atmel,24c128";
+ reg = <0x51>;
+ };
+
+ eeprom@54 {
+ compatible = "atmel,24c128";
+ reg = <0x54>;
+ };
+ };
};
};
@@ -270,15 +389,174 @@ &i2c9 {
bus-frequency = <400000>;
i2c-mux@71 {
compatible = "nxp,pca9544";
- idle-state = <0>;
i2c-mux-idle-disconnect;
reg = <0x71>;
+
+ imux20: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ gpio@49 {
+ compatible = "nxp,pca9537";
+ reg = <0x49>;
+ };
+
+ eeprom@50 {
+ compatible = "atmel,24c128";
+ reg = <0x50>;
+ };
+
+ eeprom@51 {
+ compatible = "atmel,24c128";
+ reg = <0x51>;
+ };
+
+ eeprom@54 {
+ compatible = "atmel,24c128";
+ reg = <0x54>;
+ };
+ };
+
+ imux21: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ gpio@49 {
+ compatible = "nxp,pca9537";
+ reg = <0x49>;
+ };
+
+ eeprom@50 {
+ compatible = "atmel,24c128";
+ reg = <0x50>;
+ };
+
+ eeprom@51 {
+ compatible = "atmel,24c128";
+ reg = <0x51>;
+ };
+
+ eeprom@54 {
+ compatible = "atmel,24c128";
+ reg = <0x54>;
+ };
+ };
+
+ imux22: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ gpio@49 {
+ compatible = "nxp,pca9537";
+ reg = <0x49>;
+ };
+
+ eeprom@50 {
+ compatible = "atmel,24c128";
+ reg = <0x50>;
+ };
+
+ eeprom@51 {
+ compatible = "atmel,24c128";
+ reg = <0x51>;
+ };
+
+ eeprom@54 {
+ compatible = "atmel,24c128";
+ reg = <0x54>;
+ };
+ };
+
+ imux23: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+
+ gpio@49 {
+ compatible = "nxp,pca9537";
+ reg = <0x49>;
+ };
+
+ eeprom@50 {
+ compatible = "atmel,24c128";
+ reg = <0x50>;
+ };
+
+ eeprom@51 {
+ compatible = "atmel,24c128";
+ reg = <0x51>;
+ };
+
+ eeprom@54 {
+ compatible = "atmel,24c128";
+ reg = <0x54>;
+ };
+ };
};
};
&i2c10 {
status = "okay";
bus-frequency = <400000>;
+ i2c-mux@74 {
+ compatible = "nxp,pca9544";
+ i2c-mux-idle-disconnect;
+ reg = <0x74>;
+
+ imux28: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+
+ gpio@20 {
+ compatible = "nxp,pca9506";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ gpio@21 {
+ compatible = "nxp,pca9506";
+ reg = <0x21>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ gpio@22 {
+ compatible = "nxp,pca9506";
+ reg = <0x22>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ gpio@23 {
+ compatible = "nxp,pca9506";
+ reg = <0x23>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ gpio@24 {
+ compatible = "nxp,pca9506";
+ reg = <0x24>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-line-names =
+ "","","","",
+ "NIC0_MAIN_PWR_EN","NIC1_MAIN_PWR_EN",
+ "NIC2_MAIN_PWR_EN","NIC3_MAIN_PWR_EN",
+ "","","","","","","","",
+ "","","","","","","","",
+ "","","","","","","","";
+ };
+ };
+
+ imux29: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+ };
};
&i2c11 {
@@ -433,16 +711,14 @@ eeprom@51 {
reg = <0x51>;
};
- i2c-mux@71 {
- compatible = "nxp,pca9846";
+ i2c-mux@74 {
+ compatible = "nxp,pca9546";
#address-cells = <1>;
#size-cells = <0>;
-
- idle-state = <0>;
i2c-mux-idle-disconnect;
- reg = <0x71>;
+ reg = <0x74>;
- i2c@0 {
+ imux30: i2c@0 {
#address-cells = <1>;
#size-cells = <0>;
reg = <0>;
@@ -450,26 +726,26 @@ i2c@0 {
adc@1f {
compatible = "ti,adc128d818";
reg = <0x1f>;
- ti,mode = /bits/ 8 <2>;
+ ti,mode = /bits/ 8 <1>;
};
pwm@20{
- compatible = "max31790";
+ compatible = "maxim,max31790";
+ pwm-as-tach = <4 5>;
reg = <0x20>;
- #address-cells = <1>;
- #size-cells = <0>;
};
gpio@22{
compatible = "ti,tca6424";
reg = <0x22>;
+ gpio-controller;
+ #gpio-cells = <2>;
};
- pwm@23{
- compatible = "max31790";
- reg = <0x23>;
- #address-cells = <1>;
- #size-cells = <0>;
+ pwm@2f{
+ compatible = "maxim,max31790";
+ pwm-as-tach = <4 5>;
+ reg = <0x2f>;
};
adc@33 {
@@ -492,34 +768,34 @@ gpio@61 {
};
};
- i2c@1 {
+ imux31: i2c@1 {
#address-cells = <1>;
#size-cells = <0>;
- reg = <0>;
+ reg = <1>;
adc@1f {
compatible = "ti,adc128d818";
reg = <0x1f>;
- ti,mode = /bits/ 8 <2>;
+ ti,mode = /bits/ 8 <1>;
};
pwm@20{
- compatible = "max31790";
+ compatible = "maxim,max31790";
+ pwm-as-tach = <4 5>;
reg = <0x20>;
- #address-cells = <1>;
- #size-cells = <0>;
};
gpio@22{
compatible = "ti,tca6424";
reg = <0x22>;
+ gpio-controller;
+ #gpio-cells = <2>;
};
- pwm@23{
- compatible = "max31790";
- reg = <0x23>;
- #address-cells = <1>;
- #size-cells = <0>;
+ pwm@2f{
+ compatible = "maxim,max31790";
+ pwm-as-tach = <4 5>;
+ reg = <0x2f>;
};
adc@33 {
@@ -547,12 +823,10 @@ i2c-mux@73 {
compatible = "nxp,pca9544";
#address-cells = <1>;
#size-cells = <0>;
-
- idle-state = <0>;
i2c-mux-idle-disconnect;
reg = <0x73>;
- i2c@0 {
+ imux32: i2c@0 {
#address-cells = <1>;
#size-cells = <0>;
reg = <0>;
@@ -563,10 +837,10 @@ adc@35 {
};
};
- i2c@1 {
+ imux33: i2c@1 {
#address-cells = <1>;
#size-cells = <0>;
- reg = <0>;
+ reg = <1>;
adc@35 {
compatible = "maxim,max11617";
@@ -589,9 +863,48 @@ mctp@10 {
i2c-mux@72 {
compatible = "nxp,pca9544";
- idle-state = <0>;
i2c-mux-idle-disconnect;
reg = <0x72>;
+
+ imux24: i2c@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ temperature-sensor@1f {
+ compatible = "ti,tmp421";
+ reg = <0x1f>;
+ };
+ };
+
+ imux25: i2c@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ temperature-sensor@1f {
+ compatible = "ti,tmp421";
+ reg = <0x1f>;
+ };
+ };
+
+ imux26: i2c@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ temperature-sensor@1f {
+ compatible = "ti,tmp421";
+ reg = <0x1f>;
+ };
+ };
+
+ imux27: i2c@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ temperature-sensor@1f {
+ compatible = "ti,tmp421";
+ reg = <0x1f>;
+ };
+ };
};
};
--
2.25.1
next prev parent reply other threads:[~2023-12-11 2:50 UTC|newest]
Thread overview: 18+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-12-11 2:49 [PATCH v2 00/14] Add i2c-mux and eeprom devices for Meta Yosemite 4 Delphine CC Chiu
2023-12-11 2:49 ` Delphine CC Chiu [this message]
2023-12-11 2:49 ` [PATCH v2 02/14] ARM: dts: aspeed: yosemite4: Enable adc15 Delphine CC Chiu
2023-12-11 2:49 ` [PATCH v2 03/14] ARM: dts: aspeed: yosemite4: Enable spi-gpio setting Delphine CC Chiu
2023-12-11 2:49 ` [PATCH v2 04/14] ARM: dts: aspeed: yosemite4: Enable watchdog2 Delphine CC Chiu
2023-12-11 2:49 ` [PATCH v2 05/14] ARM: dts: aspeed: yosemite4: Revise quad mode to dual mode Delphine CC Chiu
2023-12-11 2:49 ` [PATCH v2 06/14] ARM: dts: aspeed: yosemite4: Revise power sensor adm1281 for schematic change Delphine CC Chiu
2023-12-11 2:49 ` [PATCH v2 07/14] ARM: dts: aspeed: yosemite4: Add gpio pca9506 Delphine CC Chiu
2023-12-11 2:49 ` [PATCH v2 08/14] ARM: dts: aspeed: yosemite4: Revise i2c11 and i2c12 schematic change Delphine CC Chiu
2023-12-11 8:04 ` Krzysztof Kozlowski
2023-12-11 2:49 ` [PATCH v2 09/14] ARM: dts: aspeed: yosemite4: Revise i2c14 and i2c15 " Delphine CC Chiu
2023-12-11 2:49 ` [PATCH v2 10/14] ARM: dts: aspeed: yosemite4: Initialize bmc gpio state Delphine CC Chiu
2023-12-11 8:05 ` Krzysztof Kozlowski
2023-12-11 2:49 ` [PATCH v2 11/14] ARM: dts: aspeed: yosemite4: Revise mx31790 fan tach config Delphine CC Chiu
2023-12-11 2:49 ` [PATCH v2 12/14] ARM: dts: aspeed: yosemite4: add mctp config for NIC Delphine CC Chiu
2023-12-11 8:05 ` Krzysztof Kozlowski
2023-12-11 2:49 ` [PATCH v2 13/14] ARM: dts: aspeed: yosemite4: support mux to cpld Delphine CC Chiu
2023-12-11 2:49 ` [PATCH v2 14/14] ARM: dts: aspeed: yosemite4: Revise gpio name Delphine CC Chiu
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20231211024947.3990898-2-Delphine_CC_Chiu@wiwynn.com \
--to=delphine_cc_chiu@wiwynn.com \
--cc=andrew@codeconstruct.com.au \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=joel@jms.id.au \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-aspeed@lists.ozlabs.org \
--cc=linux-kernel@vger.kernel.org \
--cc=patrick@stwcx.xyz \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).