[RFC net-next v2 0/3] net: dsa: microchip: implement PHY loopback

[RFC net-next v2 0/3] net: dsa: microchip: implement PHY loopback

[Oleksij Rempel]

changes v2:
- add Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> to first 2
  patches
- make sure reverse x-mas tree is present in all patches
- add new lines between if statements
- reword commit message of the 3. patch 

Oleksij Rempel (3):
  net: dsa: microchip: ksz8: move BMCR specific code to separate
    function
  net: dsa: microchip: Remove redundant optimization in ksz8_w_phy_bmcr
  net: dsa: microchip: implement PHY loopback configuration for KSZ8794
    and KSZ8873

 drivers/net/dsa/microchip/ksz8795.c     | 360 +++++++++++++++---------
 drivers/net/dsa/microchip/ksz8795_reg.h |   1 +
 2 files changed, 230 insertions(+), 131 deletions(-)

-- 
2.39.2

[RFC net-next v2 1/3] net: dsa: microchip: ksz8: move BMCR specific code to separate function

[Oleksij Rempel]

Isolate the Basic Mode Control Register (BMCR) operations in the ksz8795
driver by moving the BMCR-related code segments from the ksz8_r_phy()
and ksz8_w_phy() functions to newly created ksz8_r_phy_bmcr() and
ksz8_w_phy_bmcr() functions.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
---
 drivers/net/dsa/microchip/ksz8795.c | 366 ++++++++++++++++++----------
 1 file changed, 240 insertions(+), 126 deletions(-)

diff --git a/drivers/net/dsa/microchip/ksz8795.c b/drivers/net/dsa/microchip/ksz8795.c
index 61b71bcfe396..1269dde832bd 100644
--- a/drivers/net/dsa/microchip/ksz8795.c
+++ b/drivers/net/dsa/microchip/ksz8795.c
@@ -676,59 +676,118 @@ static int ksz8_r_phy_ctrl(struct ksz_device *dev, int port, u16 *val)
 	return 0;
 }
 
+/**
+ * ksz8_r_phy_bmcr - Translates and reads from the SMI interface to a MIIM PHY
+ *		     Basic mode control register (Reg. 0).
+ * @dev: The KSZ device instance.
+ * @port: The port number to be read.
+ * @val: The value read from the SMI interface.
+ *
+ * This function reads the SMI interface and translates the hardware register
+ * bit values into their corresponding control settings for a MIIM PHY Basic
+ * mode control register.
+ *
+ * MIIM Bit Mapping Comparison between KSZ8794 and KSZ8873
+ * -------------------------------------------------------------------
+ * MIIM Bit                    | KSZ8794 Reg/Bit             | KSZ8873 Reg/Bit
+ * ----------------------------+-----------------------------+----------------
+ * Bit 15 - Soft Reset         | 0xF/4                       | Not supported
+ * Bit 14 - Loopback           | 0xD/0 (MAC), 0xF/7 (PHY)    ~ 0xD/0 (PHY)
+ * Bit 13 - Force 100          | 0xC/6                       = 0xC/6
+ * Bit 12 - AN Enable          | 0xC/7 (reverse logic)       ~ 0xC/7
+ * Bit 11 - Power Down         | 0xD/3                       = 0xD/3
+ * Bit 10 - PHY Isolate        | 0xF/5                       | Not supported
+ * Bit 9 - Restart AN          | 0xD/5                       = 0xD/5
+ * Bit 8 - Force Full-Duplex   | 0xC/5                       = 0xC/5
+ * Bit 7 - Collision Test/Res. | Not supported               | Not supported
+ * Bit 6 - Reserved            | Not supported               | Not supported
+ * Bit 5 - Hp_mdix             | 0x9/7                       ~ 0xF/7
+ * Bit 4 - Force MDI           | 0xD/1                       = 0xD/1
+ * Bit 3 - Disable MDIX        | 0xD/2                       = 0xD/2
+ * Bit 2 - Disable Far-End F.  | ????                        | 0xD/4
+ * Bit 1 - Disable Transmit    | 0xD/6                       = 0xD/6
+ * Bit 0 - Disable LED         | 0xD/7                       = 0xD/7
+ * -------------------------------------------------------------------
+ *
+ * Return: 0 on success, error code on failure.
+ */
+static int ksz8_r_phy_bmcr(struct ksz_device *dev, u16 port, u16 *val)
+{
+	const u16 *regs = dev->info->regs;
+	u8 restart, speed, ctrl;
+	int ret;
+
+	*val = 0;
+
+	ret = ksz_pread8(dev, port, regs[P_NEG_RESTART_CTRL], &restart);
+	if (ret)
+		return ret;
+
+	ret = ksz_pread8(dev, port, regs[P_SPEED_STATUS], &speed);
+	if (ret)
+		return ret;
+
+	ret = ksz_pread8(dev, port, regs[P_FORCE_CTRL], &ctrl);
+	if (ret)
+		return ret;
+
+	if (restart & PORT_PHY_LOOPBACK)
+		*val |= BMCR_LOOPBACK;
+
+	if (ctrl & PORT_FORCE_100_MBIT)
+		*val |= BMCR_SPEED100;
+
+	if (ksz_is_ksz88x3(dev)) {
+		if ((ctrl & PORT_AUTO_NEG_ENABLE))
+			*val |= BMCR_ANENABLE;
+	} else {
+		if (!(ctrl & PORT_AUTO_NEG_DISABLE))
+			*val |= BMCR_ANENABLE;
+	}
+
+	if (restart & PORT_POWER_DOWN)
+		*val |= BMCR_PDOWN;
+
+	if (restart & PORT_AUTO_NEG_RESTART)
+		*val |= BMCR_ANRESTART;
+
+	if (ctrl & PORT_FORCE_FULL_DUPLEX)
+		*val |= BMCR_FULLDPLX;
+
+	if (speed & PORT_HP_MDIX)
+		*val |= KSZ886X_BMCR_HP_MDIX;
+
+	if (restart & PORT_FORCE_MDIX)
+		*val |= KSZ886X_BMCR_FORCE_MDI;
+
+	if (restart & PORT_AUTO_MDIX_DISABLE)
+		*val |= KSZ886X_BMCR_DISABLE_AUTO_MDIX;
+
+	if (restart & PORT_TX_DISABLE)
+		*val |= KSZ886X_BMCR_DISABLE_TRANSMIT;
+
+	if (restart & PORT_LED_OFF)
+		*val |= KSZ886X_BMCR_DISABLE_LED;
+
+	return 0;
+}
+
 int ksz8_r_phy(struct ksz_device *dev, u16 phy, u16 reg, u16 *val)
 {
-	u8 restart, speed, ctrl, link;
+	u8 ctrl, link, val1, val2;
 	int processed = true;
 	const u16 *regs;
-	u8 val1, val2;
 	u16 data = 0;
-	u8 p = phy;
+	u16 p = phy;
 	int ret;
 
 	regs = dev->info->regs;
 
 	switch (reg) {
 	case MII_BMCR:
-		ret = ksz_pread8(dev, p, regs[P_NEG_RESTART_CTRL], &restart);
+		ret = ksz8_r_phy_bmcr(dev, p, &data);
 		if (ret)
 			return ret;
-
-		ret = ksz_pread8(dev, p, regs[P_SPEED_STATUS], &speed);
-		if (ret)
-			return ret;
-
-		ret = ksz_pread8(dev, p, regs[P_FORCE_CTRL], &ctrl);
-		if (ret)
-			return ret;
-
-		if (restart & PORT_PHY_LOOPBACK)
-			data |= BMCR_LOOPBACK;
-		if (ctrl & PORT_FORCE_100_MBIT)
-			data |= BMCR_SPEED100;
-		if (ksz_is_ksz88x3(dev)) {
-			if ((ctrl & PORT_AUTO_NEG_ENABLE))
-				data |= BMCR_ANENABLE;
-		} else {
-			if (!(ctrl & PORT_AUTO_NEG_DISABLE))
-				data |= BMCR_ANENABLE;
-		}
-		if (restart & PORT_POWER_DOWN)
-			data |= BMCR_PDOWN;
-		if (restart & PORT_AUTO_NEG_RESTART)
-			data |= BMCR_ANRESTART;
-		if (ctrl & PORT_FORCE_FULL_DUPLEX)
-			data |= BMCR_FULLDPLX;
-		if (speed & PORT_HP_MDIX)
-			data |= KSZ886X_BMCR_HP_MDIX;
-		if (restart & PORT_FORCE_MDIX)
-			data |= KSZ886X_BMCR_FORCE_MDI;
-		if (restart & PORT_AUTO_MDIX_DISABLE)
-			data |= KSZ886X_BMCR_DISABLE_AUTO_MDIX;
-		if (restart & PORT_TX_DISABLE)
-			data |= KSZ886X_BMCR_DISABLE_TRANSMIT;
-		if (restart & PORT_LED_OFF)
-			data |= KSZ886X_BMCR_DISABLE_LED;
 		break;
 	case MII_BMSR:
 		ret = ksz_pread8(dev, p, regs[P_LINK_STATUS], &link);
@@ -860,113 +919,168 @@ static int ksz8_w_phy_ctrl(struct ksz_device *dev, int port, u16 val)
 	return ret;
 }
 
-int ksz8_w_phy(struct ksz_device *dev, u16 phy, u16 reg, u16 val)
+/**
+ * ksz8_w_phy_bmcr - Translates and writes to the SMI interface from a MIIM PHY
+ *		     Basic mode control register (Reg. 0).
+ * @dev: The KSZ device instance.
+ * @port: The port number to be configured.
+ * @val: The register value to be written.
+ *
+ * This function translates control settings from a MIIM PHY Basic mode control
+ * register into their corresponding hardware register bit values for the SMI
+ * interface.
+ *
+ * MIIM Bit Mapping Comparison between KSZ8794 and KSZ8873
+ * -------------------------------------------------------------------
+ * MIIM Bit                    | KSZ8794 Reg/Bit             | KSZ8873 Reg/Bit
+ * ----------------------------+-----------------------------+----------------
+ * Bit 15 - Soft Reset         | 0xF/4                       | Not supported
+ * Bit 14 - Loopback           | 0xD/0 (MAC), 0xF/7 (PHY)    ~ 0xD/0 (PHY)
+ * Bit 13 - Force 100          | 0xC/6                       = 0xC/6
+ * Bit 12 - AN Enable          | 0xC/7 (reverse logic)       ~ 0xC/7
+ * Bit 11 - Power Down         | 0xD/3                       = 0xD/3
+ * Bit 10 - PHY Isolate        | 0xF/5                       | Not supported
+ * Bit 9 - Restart AN          | 0xD/5                       = 0xD/5
+ * Bit 8 - Force Full-Duplex   | 0xC/5                       = 0xC/5
+ * Bit 7 - Collision Test/Res. | Not supported               | Not supported
+ * Bit 6 - Reserved            | Not supported               | Not supported
+ * Bit 5 - Hp_mdix             | 0x9/7                       ~ 0xF/7
+ * Bit 4 - Force MDI           | 0xD/1                       = 0xD/1
+ * Bit 3 - Disable MDIX        | 0xD/2                       = 0xD/2
+ * Bit 2 - Disable Far-End F.  | ????                        | 0xD/4
+ * Bit 1 - Disable Transmit    | 0xD/6                       = 0xD/6
+ * Bit 0 - Disable LED         | 0xD/7                       = 0xD/7
+ * -------------------------------------------------------------------
+ *
+ * Return: 0 on success, error code on failure.
+ */
+static int ksz8_w_phy_bmcr(struct ksz_device *dev, u16 port, u16 val)
 {
-	u8 restart, speed, ctrl, data;
-	const u16 *regs;
-	u8 p = phy;
+	const u16 *regs = dev->info->regs;
+	u8 restart, ctrl, speed, data;
 	int ret;
 
-	regs = dev->info->regs;
+	/* Do not support PHY reset function. */
+	if (val & BMCR_RESET)
+		return 0;
 
-	switch (reg) {
-	case MII_BMCR:
+	ret = ksz_pread8(dev, port, regs[P_SPEED_STATUS], &speed);
+	if (ret)
+		return ret;
 
-		/* Do not support PHY reset function. */
-		if (val & BMCR_RESET)
-			break;
-		ret = ksz_pread8(dev, p, regs[P_SPEED_STATUS], &speed);
+	data = speed;
+	if (val & KSZ886X_BMCR_HP_MDIX)
+		data |= PORT_HP_MDIX;
+	else
+		data &= ~PORT_HP_MDIX;
+
+	if (data != speed) {
+		ret = ksz_pwrite8(dev, port, regs[P_SPEED_STATUS], data);
 		if (ret)
 			return ret;
+	}
+
+	ret = ksz_pread8(dev, port, regs[P_FORCE_CTRL], &ctrl);
+	if (ret)
+		return ret;
 
-		data = speed;
-		if (val & KSZ886X_BMCR_HP_MDIX)
-			data |= PORT_HP_MDIX;
+	data = ctrl;
+	if (ksz_is_ksz88x3(dev)) {
+		if ((val & BMCR_ANENABLE))
+			data |= PORT_AUTO_NEG_ENABLE;
+		else
+			data &= ~PORT_AUTO_NEG_ENABLE;
+	} else {
+		if (!(val & BMCR_ANENABLE))
+			data |= PORT_AUTO_NEG_DISABLE;
 		else
-			data &= ~PORT_HP_MDIX;
+			data &= ~PORT_AUTO_NEG_DISABLE;
 
-		if (data != speed) {
-			ret = ksz_pwrite8(dev, p, regs[P_SPEED_STATUS], data);
-			if (ret)
-				return ret;
-		}
+		/* Fiber port does not support auto-negotiation. */
+		if (dev->ports[port].fiber)
+			data |= PORT_AUTO_NEG_DISABLE;
+	}
+
+	if (val & BMCR_SPEED100)
+		data |= PORT_FORCE_100_MBIT;
+	else
+		data &= ~PORT_FORCE_100_MBIT;
+
+	if (val & BMCR_FULLDPLX)
+		data |= PORT_FORCE_FULL_DUPLEX;
+	else
+		data &= ~PORT_FORCE_FULL_DUPLEX;
 
-		ret = ksz_pread8(dev, p, regs[P_FORCE_CTRL], &ctrl);
+	if (data != ctrl) {
+		ret = ksz_pwrite8(dev, port, regs[P_FORCE_CTRL], data);
 		if (ret)
 			return ret;
+	}
 
-		data = ctrl;
-		if (ksz_is_ksz88x3(dev)) {
-			if ((val & BMCR_ANENABLE))
-				data |= PORT_AUTO_NEG_ENABLE;
-			else
-				data &= ~PORT_AUTO_NEG_ENABLE;
-		} else {
-			if (!(val & BMCR_ANENABLE))
-				data |= PORT_AUTO_NEG_DISABLE;
-			else
-				data &= ~PORT_AUTO_NEG_DISABLE;
-
-			/* Fiber port does not support auto-negotiation. */
-			if (dev->ports[p].fiber)
-				data |= PORT_AUTO_NEG_DISABLE;
-		}
+	ret = ksz_pread8(dev, port, regs[P_NEG_RESTART_CTRL], &restart);
+	if (ret)
+		return ret;
 
-		if (val & BMCR_SPEED100)
-			data |= PORT_FORCE_100_MBIT;
-		else
-			data &= ~PORT_FORCE_100_MBIT;
-		if (val & BMCR_FULLDPLX)
-			data |= PORT_FORCE_FULL_DUPLEX;
-		else
-			data &= ~PORT_FORCE_FULL_DUPLEX;
+	data = restart;
+	if (val & KSZ886X_BMCR_DISABLE_LED)
+		data |= PORT_LED_OFF;
+	else
+		data &= ~PORT_LED_OFF;
 
-		if (data != ctrl) {
-			ret = ksz_pwrite8(dev, p, regs[P_FORCE_CTRL], data);
-			if (ret)
-				return ret;
-		}
+	if (val & KSZ886X_BMCR_DISABLE_TRANSMIT)
+		data |= PORT_TX_DISABLE;
+	else
+		data &= ~PORT_TX_DISABLE;
 
-		ret = ksz_pread8(dev, p, regs[P_NEG_RESTART_CTRL], &restart);
+	if (val & BMCR_ANRESTART)
+		data |= PORT_AUTO_NEG_RESTART;
+	else
+		data &= ~(PORT_AUTO_NEG_RESTART);
+
+	if (val & BMCR_PDOWN)
+		data |= PORT_POWER_DOWN;
+	else
+		data &= ~PORT_POWER_DOWN;
+
+	if (val & KSZ886X_BMCR_DISABLE_AUTO_MDIX)
+		data |= PORT_AUTO_MDIX_DISABLE;
+	else
+		data &= ~PORT_AUTO_MDIX_DISABLE;
+
+	if (val & KSZ886X_BMCR_FORCE_MDI)
+		data |= PORT_FORCE_MDIX;
+	else
+		data &= ~PORT_FORCE_MDIX;
+
+	if (val & BMCR_LOOPBACK)
+		data |= PORT_PHY_LOOPBACK;
+	else
+		data &= ~PORT_PHY_LOOPBACK;
+
+	if (data != restart) {
+		ret = ksz_pwrite8(dev, port, regs[P_NEG_RESTART_CTRL],
+				  data);
 		if (ret)
 			return ret;
+	}
 
-		data = restart;
-		if (val & KSZ886X_BMCR_DISABLE_LED)
-			data |= PORT_LED_OFF;
-		else
-			data &= ~PORT_LED_OFF;
-		if (val & KSZ886X_BMCR_DISABLE_TRANSMIT)
-			data |= PORT_TX_DISABLE;
-		else
-			data &= ~PORT_TX_DISABLE;
-		if (val & BMCR_ANRESTART)
-			data |= PORT_AUTO_NEG_RESTART;
-		else
-			data &= ~(PORT_AUTO_NEG_RESTART);
-		if (val & BMCR_PDOWN)
-			data |= PORT_POWER_DOWN;
-		else
-			data &= ~PORT_POWER_DOWN;
-		if (val & KSZ886X_BMCR_DISABLE_AUTO_MDIX)
-			data |= PORT_AUTO_MDIX_DISABLE;
-		else
-			data &= ~PORT_AUTO_MDIX_DISABLE;
-		if (val & KSZ886X_BMCR_FORCE_MDI)
-			data |= PORT_FORCE_MDIX;
-		else
-			data &= ~PORT_FORCE_MDIX;
-		if (val & BMCR_LOOPBACK)
-			data |= PORT_PHY_LOOPBACK;
-		else
-			data &= ~PORT_PHY_LOOPBACK;
+	return 0;
+}
 
-		if (data != restart) {
-			ret = ksz_pwrite8(dev, p, regs[P_NEG_RESTART_CTRL],
-					  data);
-			if (ret)
-				return ret;
-		}
+int ksz8_w_phy(struct ksz_device *dev, u16 phy, u16 reg, u16 val)
+{
+	const u16 *regs;
+	u8 ctrl, data;
+	u16 p = phy;
+	int ret;
+
+	regs = dev->info->regs;
+
+	switch (reg) {
+	case MII_BMCR:
+		ret = ksz8_w_phy_bmcr(dev, p, val);
+		if (ret)
+			return ret;
 		break;
 	case MII_ADVERTISE:
 		ret = ksz_pread8(dev, p, regs[P_LOCAL_CTRL], &ctrl);
-- 
2.39.2

[RFC net-next v2 2/3] net: dsa: microchip: Remove redundant optimization in ksz8_w_phy_bmcr

[Oleksij Rempel]

Remove the manual checks for register value changes in the
ksz8_w_phy_bmcr function. Instead, rely on regmap_update_bits() for
optimizing register updates.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
---
 drivers/net/dsa/microchip/ksz8795.c | 96 +++++++++--------------------
 1 file changed, 29 insertions(+), 67 deletions(-)

diff --git a/drivers/net/dsa/microchip/ksz8795.c b/drivers/net/dsa/microchip/ksz8795.c
index 1269dde832bd..51e0194453df 100644
--- a/drivers/net/dsa/microchip/ksz8795.c
+++ b/drivers/net/dsa/microchip/ksz8795.c
@@ -956,115 +956,77 @@ static int ksz8_w_phy_ctrl(struct ksz_device *dev, int port, u16 val)
  */
 static int ksz8_w_phy_bmcr(struct ksz_device *dev, u16 port, u16 val)
 {
+	u8 restart, speed, ctrl, restart_mask;
 	const u16 *regs = dev->info->regs;
-	u8 restart, ctrl, speed, data;
 	int ret;
 
 	/* Do not support PHY reset function. */
 	if (val & BMCR_RESET)
 		return 0;
 
-	ret = ksz_pread8(dev, port, regs[P_SPEED_STATUS], &speed);
-	if (ret)
-		return ret;
-
-	data = speed;
+	speed = 0;
 	if (val & KSZ886X_BMCR_HP_MDIX)
-		data |= PORT_HP_MDIX;
-	else
-		data &= ~PORT_HP_MDIX;
-
-	if (data != speed) {
-		ret = ksz_pwrite8(dev, port, regs[P_SPEED_STATUS], data);
-		if (ret)
-			return ret;
-	}
+		speed |= PORT_HP_MDIX;
 
-	ret = ksz_pread8(dev, port, regs[P_FORCE_CTRL], &ctrl);
+	ret = ksz_prmw8(dev, port, regs[P_SPEED_STATUS], PORT_HP_MDIX, speed);
 	if (ret)
 		return ret;
 
-	data = ctrl;
+	ctrl = 0;
 	if (ksz_is_ksz88x3(dev)) {
 		if ((val & BMCR_ANENABLE))
-			data |= PORT_AUTO_NEG_ENABLE;
-		else
-			data &= ~PORT_AUTO_NEG_ENABLE;
+			ctrl |= PORT_AUTO_NEG_ENABLE;
 	} else {
 		if (!(val & BMCR_ANENABLE))
-			data |= PORT_AUTO_NEG_DISABLE;
-		else
-			data &= ~PORT_AUTO_NEG_DISABLE;
+			ctrl |= PORT_AUTO_NEG_DISABLE;
 
 		/* Fiber port does not support auto-negotiation. */
 		if (dev->ports[port].fiber)
-			data |= PORT_AUTO_NEG_DISABLE;
+			ctrl |= PORT_AUTO_NEG_DISABLE;
 	}
 
 	if (val & BMCR_SPEED100)
-		data |= PORT_FORCE_100_MBIT;
-	else
-		data &= ~PORT_FORCE_100_MBIT;
+		ctrl |= PORT_FORCE_100_MBIT;
 
 	if (val & BMCR_FULLDPLX)
-		data |= PORT_FORCE_FULL_DUPLEX;
-	else
-		data &= ~PORT_FORCE_FULL_DUPLEX;
-
-	if (data != ctrl) {
-		ret = ksz_pwrite8(dev, port, regs[P_FORCE_CTRL], data);
-		if (ret)
-			return ret;
-	}
+		ctrl |= PORT_FORCE_FULL_DUPLEX;
 
-	ret = ksz_pread8(dev, port, regs[P_NEG_RESTART_CTRL], &restart);
+	ret = ksz_prmw8(dev, port, regs[P_FORCE_CTRL], PORT_FORCE_100_MBIT |
+		 /* PORT_AUTO_NEG_ENABLE and PORT_AUTO_NEG_DISABLE are the same
+		  * bits
+		  */
+		 PORT_FORCE_FULL_DUPLEX | PORT_AUTO_NEG_ENABLE, ctrl);
 	if (ret)
 		return ret;
 
-	data = restart;
+	restart = 0;
+	restart_mask = PORT_LED_OFF | PORT_TX_DISABLE | PORT_AUTO_NEG_RESTART |
+		PORT_POWER_DOWN | PORT_AUTO_MDIX_DISABLE | PORT_FORCE_MDIX |
+		PORT_PHY_LOOPBACK;
+
 	if (val & KSZ886X_BMCR_DISABLE_LED)
-		data |= PORT_LED_OFF;
-	else
-		data &= ~PORT_LED_OFF;
+		restart |= PORT_LED_OFF;
 
 	if (val & KSZ886X_BMCR_DISABLE_TRANSMIT)
-		data |= PORT_TX_DISABLE;
-	else
-		data &= ~PORT_TX_DISABLE;
+		restart |= PORT_TX_DISABLE;
 
 	if (val & BMCR_ANRESTART)
-		data |= PORT_AUTO_NEG_RESTART;
-	else
-		data &= ~(PORT_AUTO_NEG_RESTART);
+		restart |= PORT_AUTO_NEG_RESTART;
 
 	if (val & BMCR_PDOWN)
-		data |= PORT_POWER_DOWN;
-	else
-		data &= ~PORT_POWER_DOWN;
+		restart |= PORT_POWER_DOWN;
 
 	if (val & KSZ886X_BMCR_DISABLE_AUTO_MDIX)
-		data |= PORT_AUTO_MDIX_DISABLE;
-	else
-		data &= ~PORT_AUTO_MDIX_DISABLE;
+		restart |= PORT_AUTO_MDIX_DISABLE;
 
 	if (val & KSZ886X_BMCR_FORCE_MDI)
-		data |= PORT_FORCE_MDIX;
-	else
-		data &= ~PORT_FORCE_MDIX;
+		restart |= PORT_FORCE_MDIX;
 
 	if (val & BMCR_LOOPBACK)
-		data |= PORT_PHY_LOOPBACK;
-	else
-		data &= ~PORT_PHY_LOOPBACK;
-
-	if (data != restart) {
-		ret = ksz_pwrite8(dev, port, regs[P_NEG_RESTART_CTRL],
-				  data);
-		if (ret)
-			return ret;
-	}
+		restart |= PORT_PHY_LOOPBACK;
 
-	return 0;
+	return ksz_prmw8(dev, port, regs[P_NEG_RESTART_CTRL], restart_mask,
+			 restart);
 }
 
 int ksz8_w_phy(struct ksz_device *dev, u16 phy, u16 reg, u16 val)
-- 
2.39.2

[RFC net-next v2 3/3] net: dsa: microchip: implement PHY loopback configuration for KSZ8794 and KSZ8873

[Oleksij Rempel]

Correct the PHY loopback bit handling in the ksz8_w_phy_bmcr and
ksz8_r_phy_bmcr functions for KSZ8794 and KSZ8873 variants in the ksz8795
driver. Previously, the code erroneously used Bit 7 of port register 0xD
for both chip variants, which is actually for LED configuration. This
update ensures the correct registers and bits are used for the PHY
loopback feature:

- For KSZ8794: Use 0xF / Bit 7.
- For KSZ8873: Use 0xD / Bit 0.

The lack of loopback support was seen on KSZ8873 system by using
"ethtool -t lanX". After this patch, the ethtool selftest will work,
but only if port is not part of a bridge.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
---
 drivers/net/dsa/microchip/ksz8795.c     | 36 ++++++++++++++++++++-----
 drivers/net/dsa/microchip/ksz8795_reg.h |  1 +
 2 files changed, 30 insertions(+), 7 deletions(-)

diff --git a/drivers/net/dsa/microchip/ksz8795.c b/drivers/net/dsa/microchip/ksz8795.c
index 51e0194453df..1d8377640a3d 100644
--- a/drivers/net/dsa/microchip/ksz8795.c
+++ b/drivers/net/dsa/microchip/ksz8795.c
@@ -731,16 +731,25 @@ static int ksz8_r_phy_bmcr(struct ksz_device *dev, u16 port, u16 *val)
 	if (ret)
 		return ret;
 
-	if (restart & PORT_PHY_LOOPBACK)
-		*val |= BMCR_LOOPBACK;
-
 	if (ctrl & PORT_FORCE_100_MBIT)
 		*val |= BMCR_SPEED100;
 
 	if (ksz_is_ksz88x3(dev)) {
+		if (restart & KSZ8873_PORT_PHY_LOOPBACK)
+			*val |= BMCR_LOOPBACK;
+
 		if ((ctrl & PORT_AUTO_NEG_ENABLE))
 			*val |= BMCR_ANENABLE;
 	} else {
+		u8 stat3;
+
+		ret = ksz_pread8(dev, port, REG_PORT_STATUS_3, &stat3);
+		if (ret)
+			return ret;
+
+		if (stat3 & PORT_PHY_LOOPBACK)
+			*val |= BMCR_LOOPBACK;
+
 		if (!(ctrl & PORT_AUTO_NEG_DISABLE))
 			*val |= BMCR_ANENABLE;
 	}
@@ -1001,8 +1010,7 @@ static int ksz8_w_phy_bmcr(struct ksz_device *dev, u16 port, u16 val)
 
 	restart = 0;
 	restart_mask = PORT_LED_OFF | PORT_TX_DISABLE | PORT_AUTO_NEG_RESTART |
-		PORT_POWER_DOWN | PORT_AUTO_MDIX_DISABLE | PORT_FORCE_MDIX |
-		PORT_PHY_LOOPBACK;
+		PORT_POWER_DOWN | PORT_AUTO_MDIX_DISABLE | PORT_FORCE_MDIX;
 
 	if (val & KSZ886X_BMCR_DISABLE_LED)
 		restart |= PORT_LED_OFF;
@@ -1022,8 +1030,22 @@ static int ksz8_w_phy_bmcr(struct ksz_device *dev, u16 port, u16 val)
 	if (val & KSZ886X_BMCR_FORCE_MDI)
 		restart |= PORT_FORCE_MDIX;
 
-	if (val & BMCR_LOOPBACK)
-		restart |= PORT_PHY_LOOPBACK;
+	if (ksz_is_ksz88x3(dev)) {
+		restart_mask |= KSZ8873_PORT_PHY_LOOPBACK;
+
+		if (val & BMCR_LOOPBACK)
+			restart |= KSZ8873_PORT_PHY_LOOPBACK;
+	} else {
+		u8 stat3 = 0;
+
+		if (val & BMCR_LOOPBACK)
+			stat3 |= PORT_PHY_LOOPBACK;
+
+		ret = ksz_prmw8(dev, port, REG_PORT_STATUS_3, PORT_PHY_LOOPBACK,
+				stat3);
+		if (ret)
+			return ret;
+	}
 
 	return ksz_prmw8(dev, port, regs[P_NEG_RESTART_CTRL], restart_mask,
 			 restart);
diff --git a/drivers/net/dsa/microchip/ksz8795_reg.h b/drivers/net/dsa/microchip/ksz8795_reg.h
index beca974e0171..7c9341ef73b0 100644
--- a/drivers/net/dsa/microchip/ksz8795_reg.h
+++ b/drivers/net/dsa/microchip/ksz8795_reg.h
@@ -265,6 +265,7 @@
 #define PORT_AUTO_MDIX_DISABLE		BIT(2)
 #define PORT_FORCE_MDIX			BIT(1)
 #define PORT_MAC_LOOPBACK		BIT(0)
+#define KSZ8873_PORT_PHY_LOOPBACK	BIT(0)
 
 #define REG_PORT_1_STATUS_2		0x1E
 #define REG_PORT_2_STATUS_2		0x2E
-- 
2.39.2

Re: [RFC net-next v2 1/3] net: dsa: microchip: ksz8: move BMCR specific code to separate function

[Arun.Ramadoss]

On Tue, 2024-01-09 at 10:57 +0100, Oleksij Rempel wrote:
> EXTERNAL EMAIL: Do not click links or open attachments unless you
> know the content is safe
> 
> Isolate the Basic Mode Control Register (BMCR) operations in the
> ksz8795
> driver by moving the BMCR-related code segments from the ksz8_r_phy()
> and ksz8_w_phy() functions to newly created ksz8_r_phy_bmcr() and
> ksz8_w_phy_bmcr() functions.
> 
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>

Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>

Re: [RFC net-next v2 2/3] net: dsa: microchip: Remove redundant optimization in ksz8_w_phy_bmcr

[Arun.Ramadoss]

On Tue, 2024-01-09 at 10:57 +0100, Oleksij Rempel wrote:
> EXTERNAL EMAIL: Do not click links or open attachments unless you
> know the content is safe
> 
> Remove the manual checks for register value changes in the
> ksz8_w_phy_bmcr function. Instead, rely on regmap_update_bits() for
> optimizing register updates.
> 
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>

Acked-by: Arun Ramadoss<arun.ramadoss@microchip.com>

Re: [RFC net-next v2 3/3] net: dsa: microchip: implement PHY loopback configuration for KSZ8794 and KSZ8873

[Arun.Ramadoss]

On Tue, 2024-01-09 at 10:57 +0100, Oleksij Rempel wrote:
> EXTERNAL EMAIL: Do not click links or open attachments unless you
> know the content is safe
> 
> Correct the PHY loopback bit handling in the ksz8_w_phy_bmcr and
> ksz8_r_phy_bmcr functions for KSZ8794 and KSZ8873 variants in the
> ksz8795
> driver. Previously, the code erroneously used Bit 7 of port register
> 0xD
> for both chip variants, which is actually for LED configuration. This
> update ensures the correct registers and bits are used for the PHY
> loopback feature:
> 
> - For KSZ8794: Use 0xF / Bit 7.
> - For KSZ8873: Use 0xD / Bit 0.
> 
> The lack of loopback support was seen on KSZ8873 system by using
> "ethtool -t lanX". After this patch, the ethtool selftest will work,
> but only if port is not part of a bridge.
> 
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
> ---
>  drivers/net/dsa/microchip/ksz8795.c     | 36 ++++++++++++++++++++---
> --
>  drivers/net/dsa/microchip/ksz8795_reg.h |  1 +
>  2 files changed, 30 insertions(+), 7 deletions(-)
> 
> diff --git a/drivers/net/dsa/microchip/ksz8795.c
> b/drivers/net/dsa/microchip/ksz8795.c
> index 51e0194453df..1d8377640a3d 100644
> --- a/drivers/net/dsa/microchip/ksz8795.c
> +++ b/drivers/net/dsa/microchip/ksz8795.c
> @@ -731,16 +731,25 @@ static int ksz8_r_phy_bmcr(struct ksz_device
> *dev, u16 port, u16 *val)
>         if (ret)
>                 return ret;
> 
> -       if (restart & PORT_PHY_LOOPBACK)
> -               *val |= BMCR_LOOPBACK;
> -
>         if (ctrl & PORT_FORCE_100_MBIT)
>                 *val |= BMCR_SPEED100;
> 
>         if (ksz_is_ksz88x3(dev)) {
> +               if (restart & KSZ8873_PORT_PHY_LOOPBACK)
> +                       *val |= BMCR_LOOPBACK;
> +
>                 if ((ctrl & PORT_AUTO_NEG_ENABLE))
>                         *val |= BMCR_ANENABLE;
>         } else {
> +               u8 stat3;
> +
> +               ret = ksz_pread8(dev, port, REG_PORT_STATUS_3,
> &stat3);
> +               if (ret)
> +                       return ret;
> +
> +               if (stat3 & PORT_PHY_LOOPBACK)
> +                       *val |= BMCR_LOOPBACK;
> +
>                 if (!(ctrl & PORT_AUTO_NEG_DISABLE))
>                         *val |= BMCR_ANENABLE;
>         }
> @@ -1001,8 +1010,7 @@ static int ksz8_w_phy_bmcr(struct ksz_device
> *dev, u16 port, u16 val)
> 
>         restart = 0;
>         restart_mask = PORT_LED_OFF | PORT_TX_DISABLE |
> PORT_AUTO_NEG_RESTART |
> -               PORT_POWER_DOWN | PORT_AUTO_MDIX_DISABLE |
> PORT_FORCE_MDIX |
> -               PORT_PHY_LOOPBACK;
> +               PORT_POWER_DOWN | PORT_AUTO_MDIX_DISABLE |
> PORT_FORCE_MDIX;
> 
>         if (val & KSZ886X_BMCR_DISABLE_LED)
>                 restart |= PORT_LED_OFF;
> @@ -1022,8 +1030,22 @@ static int ksz8_w_phy_bmcr(struct ksz_device
> *dev, u16 port, u16 val)
>         if (val & KSZ886X_BMCR_FORCE_MDI)
>                 restart |= PORT_FORCE_MDIX;
> 
> -       if (val & BMCR_LOOPBACK)
> -               restart |= PORT_PHY_LOOPBACK;
> +       if (ksz_is_ksz88x3(dev)) {
> +               restart_mask |= KSZ8873_PORT_PHY_LOOPBACK;
> +
> +               if (val & BMCR_LOOPBACK)
> +                       restart |= KSZ8873_PORT_PHY_LOOPBACK;
> +       } else {
> +               u8 stat3 = 0;
> +
> +               if (val & BMCR_LOOPBACK)
> +                       stat3 |= PORT_PHY_LOOPBACK;
> +
> +               ret = ksz_prmw8(dev, port, REG_PORT_STATUS_3,
> PORT_PHY_LOOPBACK,
> +                               stat3);
> +               if (ret)
> +                       return ret;

nitpick: As it is independent thing, it will be good to have wrapper
function for writing and reading phy loopback in stat3 register. 

> +       }
> 
>         return ksz_prmw8(dev, port, regs[P_NEG_RESTART_CTRL],
> restart_mask,
>                          restart);
> diff --git a/drivers/net/dsa/microchip/ksz8795_reg.h
> b/drivers/net/dsa/microchip/ksz8795_reg.h
> index beca974e0171..7c9341ef73b0 100644
> --- a/drivers/net/dsa/microchip/ksz8795_reg.h
> +++ b/drivers/net/dsa/microchip/ksz8795_reg.h
> @@ -265,6 +265,7 @@
>  #define PORT_AUTO_MDIX_DISABLE         BIT(2)
>  #define PORT_FORCE_MDIX                        BIT(1)
>  #define PORT_MAC_LOOPBACK              BIT(0)
> +#define KSZ8873_PORT_PHY_LOOPBACK      BIT(0)
> 
>  #define REG_PORT_1_STATUS_2            0x1E
>  #define REG_PORT_2_STATUS_2            0x2E
> --
> 2.39.2
>