[PATCH v4 0/3] arm64: dts: ti: am62: Add USB support for k3-am62p

[PATCH v4 0/3] arm64: dts: ti: am62: Add USB support for k3-am62p

[Roger Quadros]

Hi,

This series first adds device nodes for USB0_PHY_CTRL and USB1_PHY_CTRL
in the wkup_conf node and fixus up the USB nodes to use the newly
added nodes.

Then it adds USB support for AM62P SoC and AM62P5-SK board.

In v4, we drop the 2 new patches that were added in v3 to add the
missing PHY2 register space to the USB controller wrapper node.

Changelog in each patch.

cheers,
-roger

Roger Quadros (3):
  dt-bindings: mfd: syscon: Add ti,am62-usb-phy-ctrl compatible
  arm64: dts: ti: k3-am62/a: use sub-node for USB_PHY_CTRL registers
  arm64: dts: ti: k3-am62p: add the USB sub-system

 .../devicetree/bindings/mfd/syscon.yaml       |  1 +
 arch/arm64/boot/dts/ti/k3-am62-main.dtsi      |  4 +-
 arch/arm64/boot/dts/ti/k3-am62-wakeup.dtsi    | 10 +++
 arch/arm64/boot/dts/ti/k3-am62a-main.dtsi     |  4 +-
 arch/arm64/boot/dts/ti/k3-am62a-wakeup.dtsi   | 10 +++
 arch/arm64/boot/dts/ti/k3-am62p-main.dtsi     | 46 +++++++++++++
 arch/arm64/boot/dts/ti/k3-am62p-wakeup.dtsi   | 10 +++
 arch/arm64/boot/dts/ti/k3-am62p5-sk.dts       | 67 +++++++++++++++++++
 8 files changed, 148 insertions(+), 4 deletions(-)


base-commit: 6613476e225e090cc9aad49be7fa504e290dd33d
-- 
2.34.1

[PATCH v4 1/3] dt-bindings: mfd: syscon: Add ti,am62-usb-phy-ctrl compatible

[Roger Quadros]

Add the compatible for TI AM62 USB PHY Control register. This
register is found in the TI AM62 WKUP_CTRL_MMR0 space [1]. It
is used to indicate the USB PHY PLL reference clock rate and
core voltage level to the USB controller.

[1] - https://www.ti.com/lit/pdf/spruiv7

Signed-off-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
---

Notes:
    Changelog:
    
    v4 - no change. Added Rob's Acked-by
    
    v3 - add compatibles in alphabetical order
    https://lore.kernel.org/all/20240201120332.4811-2-rogerq@kernel.org/
    
    v2 - New patch

 Documentation/devicetree/bindings/mfd/syscon.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/mfd/syscon.yaml b/Documentation/devicetree/bindings/mfd/syscon.yaml
index 084b5c2a2a3c..9437705af92f 100644
--- a/Documentation/devicetree/bindings/mfd/syscon.yaml
+++ b/Documentation/devicetree/bindings/mfd/syscon.yaml
@@ -72,6 +72,7 @@ properties:
               - rockchip,rk3588-qos
               - rockchip,rv1126-qos
               - starfive,jh7100-sysmain
+              - ti,am62-usb-phy-ctrl
               - ti,am654-dss-oldi-io-ctrl
 
           - const: syscon
-- 
2.34.1

[PATCH v4 2/3] arm64: dts: ti: k3-am62/a: use sub-node for USB_PHY_CTRL registers

[Roger Quadros]

Exposing the entire CTRL_MMR space to syscon is not a good idea.
Add sub-nodes for USB0_PHY_CTRL and USB1_PHY_CTRL and use them
in the USB0/USB1 nodes.

Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Andrew Davis <afd@ti.com>
---

Notes:
    Changelog:
    
    v4 - no change. Added Andrew's Reviewed-by
    
    v3 - no change
    https://lore.kernel.org/all/20240201120332.4811-3-rogerq@kernel.org/
    
    v2:
    - moved am62p changes to next patch
    - use new compatible for USB PHY CTRL node

 arch/arm64/boot/dts/ti/k3-am62-main.dtsi    |  4 ++--
 arch/arm64/boot/dts/ti/k3-am62-wakeup.dtsi  | 10 ++++++++++
 arch/arm64/boot/dts/ti/k3-am62a-main.dtsi   |  4 ++--
 arch/arm64/boot/dts/ti/k3-am62a-wakeup.dtsi | 10 ++++++++++
 4 files changed, 24 insertions(+), 4 deletions(-)

diff --git a/arch/arm64/boot/dts/ti/k3-am62-main.dtsi b/arch/arm64/boot/dts/ti/k3-am62-main.dtsi
index 464b7565d085..9432ed344d52 100644
--- a/arch/arm64/boot/dts/ti/k3-am62-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am62-main.dtsi
@@ -625,7 +625,7 @@ usbss0: dwc3-usb@f900000 {
 		reg = <0x00 0x0f900000 0x00 0x800>;
 		clocks = <&k3_clks 161 3>;
 		clock-names = "ref";
-		ti,syscon-phy-pll-refclk = <&wkup_conf 0x4008>;
+		ti,syscon-phy-pll-refclk = <&usb0_phy_ctrl 0x0>;
 		#address-cells = <2>;
 		#size-cells = <2>;
 		power-domains = <&k3_pds 178 TI_SCI_PD_EXCLUSIVE>;
@@ -648,7 +648,7 @@ usbss1: dwc3-usb@f910000 {
 		reg = <0x00 0x0f910000 0x00 0x800>;
 		clocks = <&k3_clks 162 3>;
 		clock-names = "ref";
-		ti,syscon-phy-pll-refclk = <&wkup_conf 0x4018>;
+		ti,syscon-phy-pll-refclk = <&usb1_phy_ctrl 0x0>;
 		#address-cells = <2>;
 		#size-cells = <2>;
 		power-domains = <&k3_pds 179 TI_SCI_PD_EXCLUSIVE>;
diff --git a/arch/arm64/boot/dts/ti/k3-am62-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-am62-wakeup.dtsi
index fef76f52a52e..817700b2eacf 100644
--- a/arch/arm64/boot/dts/ti/k3-am62-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am62-wakeup.dtsi
@@ -19,6 +19,16 @@ chipid: chipid@14 {
 			compatible = "ti,am654-chipid";
 			reg = <0x14 0x4>;
 		};
+
+		usb0_phy_ctrl: syscon@4008 {
+			compatible = "ti,am62-usb-phy-ctrl", "syscon";
+			reg = <0x4008 0x4>;
+		};
+
+		usb1_phy_ctrl: syscon@4018 {
+			compatible = "ti,am62-usb-phy-ctrl", "syscon";
+			reg = <0x4018 0x4>;
+		};
 	};
 
 	wkup_uart0: serial@2b300000 {
diff --git a/arch/arm64/boot/dts/ti/k3-am62a-main.dtsi b/arch/arm64/boot/dts/ti/k3-am62a-main.dtsi
index f0b8c9ab1459..8311c7c44cd3 100644
--- a/arch/arm64/boot/dts/ti/k3-am62a-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am62a-main.dtsi
@@ -566,7 +566,7 @@ usbss0: dwc3-usb@f900000 {
 		reg = <0x00 0x0f900000 0x00 0x800>;
 		clocks = <&k3_clks 161 3>;
 		clock-names = "ref";
-		ti,syscon-phy-pll-refclk = <&wkup_conf 0x4008>;
+		ti,syscon-phy-pll-refclk = <&usb0_phy_ctrl 0x0>;
 		#address-cells = <2>;
 		#size-cells = <2>;
 		power-domains = <&k3_pds 178 TI_SCI_PD_EXCLUSIVE>;
@@ -589,7 +589,7 @@ usbss1: dwc3-usb@f910000 {
 		reg = <0x00 0x0f910000 0x00 0x800>;
 		clocks = <&k3_clks 162 3>;
 		clock-names = "ref";
-		ti,syscon-phy-pll-refclk = <&wkup_conf 0x4018>;
+		ti,syscon-phy-pll-refclk = <&usb1_phy_ctrl 0x0>;
 		#address-cells = <2>;
 		#size-cells = <2>;
 		power-domains = <&k3_pds 179 TI_SCI_PD_EXCLUSIVE>;
diff --git a/arch/arm64/boot/dts/ti/k3-am62a-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-am62a-wakeup.dtsi
index 4e8279fa01e1..4a375f5e0c19 100644
--- a/arch/arm64/boot/dts/ti/k3-am62a-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am62a-wakeup.dtsi
@@ -17,6 +17,16 @@ chipid: chipid@14 {
 			compatible = "ti,am654-chipid";
 			reg = <0x14 0x4>;
 		};
+
+		usb0_phy_ctrl: syscon@4008 {
+			compatible = "ti,am62-usb-phy-ctrl", "syscon";
+			reg = <0x4008 0x4>;
+		};
+
+		usb1_phy_ctrl: syscon@4018 {
+			compatible = "ti,am62-usb-phy-ctrl", "syscon";
+			reg = <0x4018 0x4>;
+		};
 	};
 
 	wkup_uart0: serial@2b300000 {
-- 
2.34.1

[PATCH v4 3/3] arm64: dts: ti: k3-am62p: add the USB sub-system

[Roger Quadros]

There are two USB instances available on the am62p5 starter kit. Include
and enable them for use on the board.

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Roger Quadros <rogerq@kernel.org>
---

Notes:
    Changelog:
    
    v4 - no change
    
    v3 - no change
    https://lore.kernel.org/all/20240201120332.4811-4-rogerq@kernel.org/
    
    v2:
    - added USB PHY CTRL node changes here
    - changed USB wrapper node names to usb@
    - changed Type-C chip node name to usb-power-control@

 arch/arm64/boot/dts/ti/k3-am62p-main.dtsi   | 46 ++++++++++++++
 arch/arm64/boot/dts/ti/k3-am62p-wakeup.dtsi | 10 +++
 arch/arm64/boot/dts/ti/k3-am62p5-sk.dts     | 67 +++++++++++++++++++++
 3 files changed, 123 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-am62p-main.dtsi b/arch/arm64/boot/dts/ti/k3-am62p-main.dtsi
index 4c51bae06b57..17d28390d587 100644
--- a/arch/arm64/boot/dts/ti/k3-am62p-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am62p-main.dtsi
@@ -560,6 +560,52 @@ sdhci2: mmc@fa20000 {
 		status = "disabled";
 	};
 
+	usbss0: usb@f900000 {
+		compatible = "ti,am62-usb";
+		reg = <0x00 0x0f900000 0x00 0x800>;
+		clocks = <&k3_clks 161 3>;
+		clock-names = "ref";
+		ti,syscon-phy-pll-refclk = <&usb0_phy_ctrl 0x0>;
+		#address-cells = <2>;
+		#size-cells = <2>;
+		power-domains = <&k3_pds 178 TI_SCI_PD_EXCLUSIVE>;
+		ranges;
+		status = "disabled";
+
+		usb0: usb@31000000 {
+			compatible = "snps,dwc3";
+			reg = <0x00 0x31000000 0x00 0x50000>;
+			interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>, /* irq.0 */
+			<GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>; /* irq.0 */
+			interrupt-names = "host", "peripheral";
+			maximum-speed = "high-speed";
+			dr_mode = "otg";
+		};
+	};
+
+	usbss1: usb@f910000 {
+		compatible = "ti,am62-usb";
+		reg = <0x00 0x0f910000 0x00 0x800>;
+		clocks = <&k3_clks 162 3>;
+		clock-names = "ref";
+		ti,syscon-phy-pll-refclk = <&usb1_phy_ctrl 0x0>;
+		#address-cells = <2>;
+		#size-cells = <2>;
+		power-domains = <&k3_pds 179 TI_SCI_PD_EXCLUSIVE>;
+		ranges;
+		status = "disabled";
+
+		usb1: usb@31100000 {
+			compatible = "snps,dwc3";
+			reg = <0x00 0x31100000 0x00 0x50000>;
+			interrupts = <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>, /* irq.0 */
+			<GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>; /* irq.0 */
+			interrupt-names = "host", "peripheral";
+			maximum-speed = "high-speed";
+			dr_mode = "otg";
+		};
+	};
+
 	fss: bus@fc00000 {
 		compatible = "simple-bus";
 		reg = <0x00 0x0fc00000 0x00 0x70000>;
diff --git a/arch/arm64/boot/dts/ti/k3-am62p-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-am62p-wakeup.dtsi
index 19f42b39394e..00dd38b02a52 100644
--- a/arch/arm64/boot/dts/ti/k3-am62p-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am62p-wakeup.dtsi
@@ -18,6 +18,16 @@ chipid: chipid@14 {
 			reg = <0x14 0x4>;
 			bootph-all;
 		};
+
+		usb0_phy_ctrl: syscon@4008 {
+			compatible = "ti,am62-usb-phy-ctrl", "syscon";
+			reg = <0x4008 0x4>;
+		};
+
+		usb1_phy_ctrl: syscon@4018 {
+			compatible = "ti,am62-usb-phy-ctrl", "syscon";
+			reg = <0x4018 0x4>;
+		};
 	};
 
 	wkup_uart0: serial@2b300000 {
diff --git a/arch/arm64/boot/dts/ti/k3-am62p5-sk.dts b/arch/arm64/boot/dts/ti/k3-am62p5-sk.dts
index 1773c05f752c..80be56c0a4e0 100644
--- a/arch/arm64/boot/dts/ti/k3-am62p5-sk.dts
+++ b/arch/arm64/boot/dts/ti/k3-am62p5-sk.dts
@@ -27,6 +27,8 @@ aliases {
 		spi0 = &ospi0;
 		ethernet0 = &cpsw_port1;
 		ethernet1 = &cpsw_port2;
+		usb0 = &usb0;
+		usb1 = &usb1;
 	};
 
 	chosen {
@@ -297,6 +299,12 @@ AM62PX_IOPAD(0x01b0, PIN_OUTPUT, 2) /* (G20) MCASP0_ACLKR.UART1_TXD */
 		bootph-all;
 	};
 
+	main_usb1_pins_default: main-usb1-default-pins {
+		pinctrl-single,pins = <
+			AM62PX_IOPAD(0x0258, PIN_INPUT, 0) /* (G21) USB1_DRVVBUS */
+		>;
+	};
+
 	main_wlirq_pins_default: main-wlirq-default-pins {
 		pinctrl-single,pins = <
 			AM62PX_IOPAD(0x0128, PIN_INPUT, 7) /* (K25) MMC2_SDWP.GPIO0_72 */
@@ -340,6 +348,36 @@ AM62PX_IOPAD(0x0124, PIN_INPUT, 7) /* (J25) MMC2_SDCD.GPIO0_71 */
 	};
 };
 
+&main_i2c0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_i2c0_pins_default>;
+	clock-frequency = <400000>;
+
+	typec_pd0: usb-power-controller@3f {
+		compatible = "ti,tps6598x";
+		reg = <0x3f>;
+
+		connector {
+			compatible = "usb-c-connector";
+			label = "USB-C";
+			self-powered;
+			data-role = "dual";
+			power-role = "sink";
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				port@0 {
+					reg = <0>;
+					usb_con_hs: endpoint {
+						remote-endpoint = <&usb0_hs_ep>;
+					};
+				};
+			};
+		};
+	};
+};
+
 &main_i2c1 {
 	status = "okay";
 	pinctrl-names = "default";
@@ -460,6 +498,35 @@ cpsw3g_phy1: ethernet-phy@1 {
 	};
 };
 
+&usbss0 {
+	status = "okay";
+	ti,vbus-divider;
+};
+
+&usbss1 {
+	status = "okay";
+	ti,vbus-divider;
+};
+
+&usb0 {
+	usb-role-switch;
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	port@0 {
+		reg = <0>;
+		usb0_hs_ep: endpoint {
+			remote-endpoint = <&usb_con_hs>;
+		};
+	};
+};
+
+&usb1 {
+	dr_mode = "host";
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_usb1_pins_default>;
+};
+
 &mcasp1 {
 	status = "okay";
 	#sound-dai-cells = <0>;
-- 
2.34.1

Re: [PATCH v4 3/3] arm64: dts: ti: k3-am62p: add the USB sub-system

[Andrew Davis]

On 2/5/24 7:59 AM, Roger Quadros wrote:
> There are two USB instances available on the am62p5 starter kit. Include
> and enable them for use on the board.
> 
> Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
> Signed-off-by: Roger Quadros <rogerq@kernel.org>
> ---
> 
> Notes:
>      Changelog:
>      
>      v4 - no change
>      
>      v3 - no change
>      https://lore.kernel.org/all/20240201120332.4811-4-rogerq@kernel.org/
>      
>      v2:
>      - added USB PHY CTRL node changes here
>      - changed USB wrapper node names to usb@
>      - changed Type-C chip node name to usb-power-control@
> 
>   arch/arm64/boot/dts/ti/k3-am62p-main.dtsi   | 46 ++++++++++++++
>   arch/arm64/boot/dts/ti/k3-am62p-wakeup.dtsi | 10 +++
>   arch/arm64/boot/dts/ti/k3-am62p5-sk.dts     | 67 +++++++++++++++++++++
>   3 files changed, 123 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/ti/k3-am62p-main.dtsi b/arch/arm64/boot/dts/ti/k3-am62p-main.dtsi
> index 4c51bae06b57..17d28390d587 100644
> --- a/arch/arm64/boot/dts/ti/k3-am62p-main.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-am62p-main.dtsi
> @@ -560,6 +560,52 @@ sdhci2: mmc@fa20000 {
>   		status = "disabled";
>   	};
>   
> +	usbss0: usb@f900000 {
> +		compatible = "ti,am62-usb";
> +		reg = <0x00 0x0f900000 0x00 0x800>;
> +		clocks = <&k3_clks 161 3>;
> +		clock-names = "ref";
> +		ti,syscon-phy-pll-refclk = <&usb0_phy_ctrl 0x0>;
> +		#address-cells = <2>;
> +		#size-cells = <2>;
> +		power-domains = <&k3_pds 178 TI_SCI_PD_EXCLUSIVE>;
> +		ranges;
> +		status = "disabled";
> +
> +		usb0: usb@31000000 {
> +			compatible = "snps,dwc3";
> +			reg = <0x00 0x31000000 0x00 0x50000>;
> +			interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>, /* irq.0 */
> +			<GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>; /* irq.0 */
> +			interrupt-names = "host", "peripheral";
> +			maximum-speed = "high-speed";
> +			dr_mode = "otg";
> +		};
> +	};
> +
> +	usbss1: usb@f910000 {
> +		compatible = "ti,am62-usb";
> +		reg = <0x00 0x0f910000 0x00 0x800>;
> +		clocks = <&k3_clks 162 3>;
> +		clock-names = "ref";
> +		ti,syscon-phy-pll-refclk = <&usb1_phy_ctrl 0x0>;
> +		#address-cells = <2>;
> +		#size-cells = <2>;
> +		power-domains = <&k3_pds 179 TI_SCI_PD_EXCLUSIVE>;
> +		ranges;
> +		status = "disabled";
> +
> +		usb1: usb@31100000 {
> +			compatible = "snps,dwc3";
> +			reg = <0x00 0x31100000 0x00 0x50000>;
> +			interrupts = <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>, /* irq.0 */
> +			<GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>; /* irq.0 */
> +			interrupt-names = "host", "peripheral";
> +			maximum-speed = "high-speed";
> +			dr_mode = "otg";
> +		};
> +	};
> +
>   	fss: bus@fc00000 {
>   		compatible = "simple-bus";
>   		reg = <0x00 0x0fc00000 0x00 0x70000>;
> diff --git a/arch/arm64/boot/dts/ti/k3-am62p-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-am62p-wakeup.dtsi
> index 19f42b39394e..00dd38b02a52 100644
> --- a/arch/arm64/boot/dts/ti/k3-am62p-wakeup.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-am62p-wakeup.dtsi
> @@ -18,6 +18,16 @@ chipid: chipid@14 {
>   			reg = <0x14 0x4>;
>   			bootph-all;
>   		};
> +
> +		usb0_phy_ctrl: syscon@4008 {
> +			compatible = "ti,am62-usb-phy-ctrl", "syscon";
> +			reg = <0x4008 0x4>;
> +		};
> +
> +		usb1_phy_ctrl: syscon@4018 {
> +			compatible = "ti,am62-usb-phy-ctrl", "syscon";
> +			reg = <0x4018 0x4>;
> +		};
>   	};
>   
>   	wkup_uart0: serial@2b300000 {
> diff --git a/arch/arm64/boot/dts/ti/k3-am62p5-sk.dts b/arch/arm64/boot/dts/ti/k3-am62p5-sk.dts
> index 1773c05f752c..80be56c0a4e0 100644
> --- a/arch/arm64/boot/dts/ti/k3-am62p5-sk.dts
> +++ b/arch/arm64/boot/dts/ti/k3-am62p5-sk.dts
> @@ -27,6 +27,8 @@ aliases {
>   		spi0 = &ospi0;
>   		ethernet0 = &cpsw_port1;
>   		ethernet1 = &cpsw_port2;
> +		usb0 = &usb0;
> +		usb1 = &usb1;
>   	};
>   
>   	chosen {
> @@ -297,6 +299,12 @@ AM62PX_IOPAD(0x01b0, PIN_OUTPUT, 2) /* (G20) MCASP0_ACLKR.UART1_TXD */
>   		bootph-all;
>   	};
>   
> +	main_usb1_pins_default: main-usb1-default-pins {
> +		pinctrl-single,pins = <
> +			AM62PX_IOPAD(0x0258, PIN_INPUT, 0) /* (G21) USB1_DRVVBUS */
> +		>;
> +	};
> +
>   	main_wlirq_pins_default: main-wlirq-default-pins {
>   		pinctrl-single,pins = <
>   			AM62PX_IOPAD(0x0128, PIN_INPUT, 7) /* (K25) MMC2_SDWP.GPIO0_72 */
> @@ -340,6 +348,36 @@ AM62PX_IOPAD(0x0124, PIN_INPUT, 7) /* (J25) MMC2_SDCD.GPIO0_71 */
>   	};
>   };
>   
> +&main_i2c0 {
> +	status = "okay";
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&main_i2c0_pins_default>;
> +	clock-frequency = <400000>;
> +
> +	typec_pd0: usb-power-controller@3f {
> +		compatible = "ti,tps6598x";
> +		reg = <0x3f>;
> +
> +		connector {
> +			compatible = "usb-c-connector";
> +			label = "USB-C";
> +			self-powered;
> +			data-role = "dual";
> +			power-role = "sink";
> +			ports {
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +				port@0 {
> +					reg = <0>;
> +					usb_con_hs: endpoint {
> +						remote-endpoint = <&usb0_hs_ep>;
> +					};
> +				};
> +			};
> +		};
> +	};
> +};
> +
>   &main_i2c1 {
>   	status = "okay";
>   	pinctrl-names = "default";
> @@ -460,6 +498,35 @@ cpsw3g_phy1: ethernet-phy@1 {
>   	};
>   };
>   
> +&usbss0 {
> +	status = "okay";
> +	ti,vbus-divider;
> +};
> +
> +&usbss1 {
> +	status = "okay";
> +	ti,vbus-divider;
> +};
> +
> +&usb0 {
> +	usb-role-switch;
> +	#address-cells = <1>;
> +	#size-cells = <0>;
> +
> +	port@0 {
> +		reg = <0>;
> +		usb0_hs_ep: endpoint {
> +			remote-endpoint = <&usb_con_hs>;
> +		};
> +	};
> +};
> +
> +&usb1 {
> +	dr_mode = "host";
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&main_usb1_pins_default>;

I'm not super familiar with USB, but I see this pinmux for the
"DRVVBUS" pin is usually added the the parent USB subsystem node (usbss).
Does this pin belong to the subsystem or the specific USB instance?

Andrew

> +};
> +
>   &mcasp1 {
>   	status = "okay";
>   	#sound-dai-cells = <0>;

Re: [PATCH v4 3/3] arm64: dts: ti: k3-am62p: add the USB sub-system

[Roger Quadros]

On 05/02/2024 19:34, Andrew Davis wrote:
> On 2/5/24 7:59 AM, Roger Quadros wrote:
>> There are two USB instances available on the am62p5 starter kit. Include
>> and enable them for use on the board.
>>
>> Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
>> Signed-off-by: Roger Quadros <rogerq@kernel.org>
>> ---
>>
>> Notes:
>>      Changelog:
>>           v4 - no change
>>           v3 - no change
>>      https://lore.kernel.org/all/20240201120332.4811-4-rogerq@kernel.org/
>>           v2:
>>      - added USB PHY CTRL node changes here
>>      - changed USB wrapper node names to usb@
>>      - changed Type-C chip node name to usb-power-control@
>>
>>   arch/arm64/boot/dts/ti/k3-am62p-main.dtsi   | 46 ++++++++++++++
>>   arch/arm64/boot/dts/ti/k3-am62p-wakeup.dtsi | 10 +++
>>   arch/arm64/boot/dts/ti/k3-am62p5-sk.dts     | 67 +++++++++++++++++++++
>>   3 files changed, 123 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/ti/k3-am62p-main.dtsi b/arch/arm64/boot/dts/ti/k3-am62p-main.dtsi
>> index 4c51bae06b57..17d28390d587 100644
>> --- a/arch/arm64/boot/dts/ti/k3-am62p-main.dtsi
>> +++ b/arch/arm64/boot/dts/ti/k3-am62p-main.dtsi
>> @@ -560,6 +560,52 @@ sdhci2: mmc@fa20000 {
>>           status = "disabled";
>>       };
>>   +    usbss0: usb@f900000 {
>> +        compatible = "ti,am62-usb";
>> +        reg = <0x00 0x0f900000 0x00 0x800>;
>> +        clocks = <&k3_clks 161 3>;
>> +        clock-names = "ref";
>> +        ti,syscon-phy-pll-refclk = <&usb0_phy_ctrl 0x0>;
>> +        #address-cells = <2>;
>> +        #size-cells = <2>;
>> +        power-domains = <&k3_pds 178 TI_SCI_PD_EXCLUSIVE>;
>> +        ranges;
>> +        status = "disabled";
>> +
>> +        usb0: usb@31000000 {
>> +            compatible = "snps,dwc3";
>> +            reg = <0x00 0x31000000 0x00 0x50000>;
>> +            interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>, /* irq.0 */
>> +            <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>; /* irq.0 */
>> +            interrupt-names = "host", "peripheral";
>> +            maximum-speed = "high-speed";
>> +            dr_mode = "otg";
>> +        };
>> +    };
>> +
>> +    usbss1: usb@f910000 {
>> +        compatible = "ti,am62-usb";
>> +        reg = <0x00 0x0f910000 0x00 0x800>;
>> +        clocks = <&k3_clks 162 3>;
>> +        clock-names = "ref";
>> +        ti,syscon-phy-pll-refclk = <&usb1_phy_ctrl 0x0>;
>> +        #address-cells = <2>;
>> +        #size-cells = <2>;
>> +        power-domains = <&k3_pds 179 TI_SCI_PD_EXCLUSIVE>;
>> +        ranges;
>> +        status = "disabled";
>> +
>> +        usb1: usb@31100000 {
>> +            compatible = "snps,dwc3";
>> +            reg = <0x00 0x31100000 0x00 0x50000>;
>> +            interrupts = <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>, /* irq.0 */
>> +            <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>; /* irq.0 */
>> +            interrupt-names = "host", "peripheral";
>> +            maximum-speed = "high-speed";
>> +            dr_mode = "otg";
>> +        };
>> +    };
>> +
>>       fss: bus@fc00000 {
>>           compatible = "simple-bus";
>>           reg = <0x00 0x0fc00000 0x00 0x70000>;
>> diff --git a/arch/arm64/boot/dts/ti/k3-am62p-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-am62p-wakeup.dtsi
>> index 19f42b39394e..00dd38b02a52 100644
>> --- a/arch/arm64/boot/dts/ti/k3-am62p-wakeup.dtsi
>> +++ b/arch/arm64/boot/dts/ti/k3-am62p-wakeup.dtsi
>> @@ -18,6 +18,16 @@ chipid: chipid@14 {
>>               reg = <0x14 0x4>;
>>               bootph-all;
>>           };
>> +
>> +        usb0_phy_ctrl: syscon@4008 {
>> +            compatible = "ti,am62-usb-phy-ctrl", "syscon";
>> +            reg = <0x4008 0x4>;
>> +        };
>> +
>> +        usb1_phy_ctrl: syscon@4018 {
>> +            compatible = "ti,am62-usb-phy-ctrl", "syscon";
>> +            reg = <0x4018 0x4>;
>> +        };
>>       };
>>         wkup_uart0: serial@2b300000 {
>> diff --git a/arch/arm64/boot/dts/ti/k3-am62p5-sk.dts b/arch/arm64/boot/dts/ti/k3-am62p5-sk.dts
>> index 1773c05f752c..80be56c0a4e0 100644
>> --- a/arch/arm64/boot/dts/ti/k3-am62p5-sk.dts
>> +++ b/arch/arm64/boot/dts/ti/k3-am62p5-sk.dts
>> @@ -27,6 +27,8 @@ aliases {
>>           spi0 = &ospi0;
>>           ethernet0 = &cpsw_port1;
>>           ethernet1 = &cpsw_port2;
>> +        usb0 = &usb0;
>> +        usb1 = &usb1;
>>       };
>>         chosen {
>> @@ -297,6 +299,12 @@ AM62PX_IOPAD(0x01b0, PIN_OUTPUT, 2) /* (G20) MCASP0_ACLKR.UART1_TXD */
>>           bootph-all;
>>       };
>>   +    main_usb1_pins_default: main-usb1-default-pins {
>> +        pinctrl-single,pins = <
>> +            AM62PX_IOPAD(0x0258, PIN_INPUT, 0) /* (G21) USB1_DRVVBUS */
>> +        >;
>> +    };
>> +
>>       main_wlirq_pins_default: main-wlirq-default-pins {
>>           pinctrl-single,pins = <
>>               AM62PX_IOPAD(0x0128, PIN_INPUT, 7) /* (K25) MMC2_SDWP.GPIO0_72 */
>> @@ -340,6 +348,36 @@ AM62PX_IOPAD(0x0124, PIN_INPUT, 7) /* (J25) MMC2_SDCD.GPIO0_71 */
>>       };
>>   };
>>   +&main_i2c0 {
>> +    status = "okay";
>> +    pinctrl-names = "default";
>> +    pinctrl-0 = <&main_i2c0_pins_default>;
>> +    clock-frequency = <400000>;
>> +
>> +    typec_pd0: usb-power-controller@3f {
>> +        compatible = "ti,tps6598x";
>> +        reg = <0x3f>;
>> +
>> +        connector {
>> +            compatible = "usb-c-connector";
>> +            label = "USB-C";
>> +            self-powered;
>> +            data-role = "dual";
>> +            power-role = "sink";
>> +            ports {
>> +                #address-cells = <1>;
>> +                #size-cells = <0>;
>> +                port@0 {
>> +                    reg = <0>;
>> +                    usb_con_hs: endpoint {
>> +                        remote-endpoint = <&usb0_hs_ep>;
>> +                    };
>> +                };
>> +            };
>> +        };
>> +    };
>> +};
>> +
>>   &main_i2c1 {
>>       status = "okay";
>>       pinctrl-names = "default";
>> @@ -460,6 +498,35 @@ cpsw3g_phy1: ethernet-phy@1 {
>>       };
>>   };
>>   +&usbss0 {
>> +    status = "okay";
>> +    ti,vbus-divider;
>> +};
>> +
>> +&usbss1 {
>> +    status = "okay";
>> +    ti,vbus-divider;
>> +};
>> +
>> +&usb0 {
>> +    usb-role-switch;
>> +    #address-cells = <1>;
>> +    #size-cells = <0>;
>> +
>> +    port@0 {
>> +        reg = <0>;
>> +        usb0_hs_ep: endpoint {
>> +            remote-endpoint = <&usb_con_hs>;
>> +        };
>> +    };
>> +};
>> +
>> +&usb1 {
>> +    dr_mode = "host";
>> +    pinctrl-names = "default";
>> +    pinctrl-0 = <&main_usb1_pins_default>;
> 
> I'm not super familiar with USB, but I see this pinmux for the
> "DRVVBUS" pin is usually added the the parent USB subsystem node (usbss).
> Does this pin belong to the subsystem or the specific USB instance?
> 
There is only 1 USB instance per USB sub-system.
The "DRVVBUS" pin is a control signal to enable the VBUS regulator
while in host mode.

Just probing the usbss1 driver has no use of "DRVVBUS".
I think usb1 is the right place as it is used there.

> Andrew
> 
>> +};
>> +
>>   &mcasp1 {
>>       status = "okay";
>>       #sound-dai-cells = <0>;

-- 
cheers,
-roger

Re: [PATCH v4 3/3] arm64: dts: ti: k3-am62p: add the USB sub-system

[Andrew Davis]

On 2/6/24 6:30 AM, Roger Quadros wrote:
> 
> 
> On 05/02/2024 19:34, Andrew Davis wrote:
>> On 2/5/24 7:59 AM, Roger Quadros wrote:
>>> There are two USB instances available on the am62p5 starter kit. Include
>>> and enable them for use on the board.
>>>
>>> Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
>>> Signed-off-by: Roger Quadros <rogerq@kernel.org>
>>> ---
>>>
>>> Notes:
>>>       Changelog:
>>>            v4 - no change
>>>            v3 - no change
>>>       https://lore.kernel.org/all/20240201120332.4811-4-rogerq@kernel.org/
>>>            v2:
>>>       - added USB PHY CTRL node changes here
>>>       - changed USB wrapper node names to usb@
>>>       - changed Type-C chip node name to usb-power-control@
>>>
>>>    arch/arm64/boot/dts/ti/k3-am62p-main.dtsi   | 46 ++++++++++++++
>>>    arch/arm64/boot/dts/ti/k3-am62p-wakeup.dtsi | 10 +++
>>>    arch/arm64/boot/dts/ti/k3-am62p5-sk.dts     | 67 +++++++++++++++++++++
>>>    3 files changed, 123 insertions(+)
>>>
>>> diff --git a/arch/arm64/boot/dts/ti/k3-am62p-main.dtsi b/arch/arm64/boot/dts/ti/k3-am62p-main.dtsi
>>> index 4c51bae06b57..17d28390d587 100644
>>> --- a/arch/arm64/boot/dts/ti/k3-am62p-main.dtsi
>>> +++ b/arch/arm64/boot/dts/ti/k3-am62p-main.dtsi
>>> @@ -560,6 +560,52 @@ sdhci2: mmc@fa20000 {
>>>            status = "disabled";
>>>        };
>>>    +    usbss0: usb@f900000 {
>>> +        compatible = "ti,am62-usb";
>>> +        reg = <0x00 0x0f900000 0x00 0x800>;
>>> +        clocks = <&k3_clks 161 3>;
>>> +        clock-names = "ref";
>>> +        ti,syscon-phy-pll-refclk = <&usb0_phy_ctrl 0x0>;
>>> +        #address-cells = <2>;
>>> +        #size-cells = <2>;
>>> +        power-domains = <&k3_pds 178 TI_SCI_PD_EXCLUSIVE>;
>>> +        ranges;
>>> +        status = "disabled";
>>> +
>>> +        usb0: usb@31000000 {
>>> +            compatible = "snps,dwc3";
>>> +            reg = <0x00 0x31000000 0x00 0x50000>;
>>> +            interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>, /* irq.0 */
>>> +            <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>; /* irq.0 */
>>> +            interrupt-names = "host", "peripheral";
>>> +            maximum-speed = "high-speed";
>>> +            dr_mode = "otg";
>>> +        };
>>> +    };
>>> +
>>> +    usbss1: usb@f910000 {
>>> +        compatible = "ti,am62-usb";
>>> +        reg = <0x00 0x0f910000 0x00 0x800>;
>>> +        clocks = <&k3_clks 162 3>;
>>> +        clock-names = "ref";
>>> +        ti,syscon-phy-pll-refclk = <&usb1_phy_ctrl 0x0>;
>>> +        #address-cells = <2>;
>>> +        #size-cells = <2>;
>>> +        power-domains = <&k3_pds 179 TI_SCI_PD_EXCLUSIVE>;
>>> +        ranges;
>>> +        status = "disabled";
>>> +
>>> +        usb1: usb@31100000 {
>>> +            compatible = "snps,dwc3";
>>> +            reg = <0x00 0x31100000 0x00 0x50000>;
>>> +            interrupts = <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>, /* irq.0 */
>>> +            <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>; /* irq.0 */
>>> +            interrupt-names = "host", "peripheral";
>>> +            maximum-speed = "high-speed";
>>> +            dr_mode = "otg";
>>> +        };
>>> +    };
>>> +
>>>        fss: bus@fc00000 {
>>>            compatible = "simple-bus";
>>>            reg = <0x00 0x0fc00000 0x00 0x70000>;
>>> diff --git a/arch/arm64/boot/dts/ti/k3-am62p-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-am62p-wakeup.dtsi
>>> index 19f42b39394e..00dd38b02a52 100644
>>> --- a/arch/arm64/boot/dts/ti/k3-am62p-wakeup.dtsi
>>> +++ b/arch/arm64/boot/dts/ti/k3-am62p-wakeup.dtsi
>>> @@ -18,6 +18,16 @@ chipid: chipid@14 {
>>>                reg = <0x14 0x4>;
>>>                bootph-all;
>>>            };
>>> +
>>> +        usb0_phy_ctrl: syscon@4008 {
>>> +            compatible = "ti,am62-usb-phy-ctrl", "syscon";
>>> +            reg = <0x4008 0x4>;
>>> +        };
>>> +
>>> +        usb1_phy_ctrl: syscon@4018 {
>>> +            compatible = "ti,am62-usb-phy-ctrl", "syscon";
>>> +            reg = <0x4018 0x4>;
>>> +        };
>>>        };
>>>          wkup_uart0: serial@2b300000 {
>>> diff --git a/arch/arm64/boot/dts/ti/k3-am62p5-sk.dts b/arch/arm64/boot/dts/ti/k3-am62p5-sk.dts
>>> index 1773c05f752c..80be56c0a4e0 100644
>>> --- a/arch/arm64/boot/dts/ti/k3-am62p5-sk.dts
>>> +++ b/arch/arm64/boot/dts/ti/k3-am62p5-sk.dts
>>> @@ -27,6 +27,8 @@ aliases {
>>>            spi0 = &ospi0;
>>>            ethernet0 = &cpsw_port1;
>>>            ethernet1 = &cpsw_port2;
>>> +        usb0 = &usb0;
>>> +        usb1 = &usb1;
>>>        };
>>>          chosen {
>>> @@ -297,6 +299,12 @@ AM62PX_IOPAD(0x01b0, PIN_OUTPUT, 2) /* (G20) MCASP0_ACLKR.UART1_TXD */
>>>            bootph-all;
>>>        };
>>>    +    main_usb1_pins_default: main-usb1-default-pins {
>>> +        pinctrl-single,pins = <
>>> +            AM62PX_IOPAD(0x0258, PIN_INPUT, 0) /* (G21) USB1_DRVVBUS */
>>> +        >;
>>> +    };
>>> +
>>>        main_wlirq_pins_default: main-wlirq-default-pins {
>>>            pinctrl-single,pins = <
>>>                AM62PX_IOPAD(0x0128, PIN_INPUT, 7) /* (K25) MMC2_SDWP.GPIO0_72 */
>>> @@ -340,6 +348,36 @@ AM62PX_IOPAD(0x0124, PIN_INPUT, 7) /* (J25) MMC2_SDCD.GPIO0_71 */
>>>        };
>>>    };
>>>    +&main_i2c0 {
>>> +    status = "okay";
>>> +    pinctrl-names = "default";
>>> +    pinctrl-0 = <&main_i2c0_pins_default>;
>>> +    clock-frequency = <400000>;
>>> +
>>> +    typec_pd0: usb-power-controller@3f {
>>> +        compatible = "ti,tps6598x";
>>> +        reg = <0x3f>;
>>> +
>>> +        connector {
>>> +            compatible = "usb-c-connector";
>>> +            label = "USB-C";
>>> +            self-powered;
>>> +            data-role = "dual";
>>> +            power-role = "sink";
>>> +            ports {
>>> +                #address-cells = <1>;
>>> +                #size-cells = <0>;
>>> +                port@0 {
>>> +                    reg = <0>;
>>> +                    usb_con_hs: endpoint {
>>> +                        remote-endpoint = <&usb0_hs_ep>;
>>> +                    };
>>> +                };
>>> +            };
>>> +        };
>>> +    };
>>> +};
>>> +
>>>    &main_i2c1 {
>>>        status = "okay";
>>>        pinctrl-names = "default";
>>> @@ -460,6 +498,35 @@ cpsw3g_phy1: ethernet-phy@1 {
>>>        };
>>>    };
>>>    +&usbss0 {
>>> +    status = "okay";
>>> +    ti,vbus-divider;
>>> +};
>>> +
>>> +&usbss1 {
>>> +    status = "okay";
>>> +    ti,vbus-divider;
>>> +};
>>> +
>>> +&usb0 {
>>> +    usb-role-switch;
>>> +    #address-cells = <1>;
>>> +    #size-cells = <0>;
>>> +
>>> +    port@0 {
>>> +        reg = <0>;
>>> +        usb0_hs_ep: endpoint {
>>> +            remote-endpoint = <&usb_con_hs>;
>>> +        };
>>> +    };
>>> +};
>>> +
>>> +&usb1 {
>>> +    dr_mode = "host";
>>> +    pinctrl-names = "default";
>>> +    pinctrl-0 = <&main_usb1_pins_default>;
>>
>> I'm not super familiar with USB, but I see this pinmux for the
>> "DRVVBUS" pin is usually added the the parent USB subsystem node (usbss).
>> Does this pin belong to the subsystem or the specific USB instance?
>>
> There is only 1 USB instance per USB sub-system.
> The "DRVVBUS" pin is a control signal to enable the VBUS regulator
> while in host mode.
> 
> Just probing the usbss1 driver has no use of "DRVVBUS".
> I think usb1 is the right place as it is used there.
> 

Seems reasonable, so if there ever was more than 1 instance
per sub-system, each instance would need its own pin?

We should move these pinctrl to the instance node in the other
dts files at some point then.

Reviewed-by: Andrew Davis <afd@ti.com>

>> Andrew
>>
>>> +};
>>> +
>>>    &mcasp1 {
>>>        status = "okay";
>>>        #sound-dai-cells = <0>;
> 

Re: [PATCH v4 3/3] arm64: dts: ti: k3-am62p: add the USB sub-system

[Roger Quadros]

On 06/02/2024 19:34, Andrew Davis wrote:
> On 2/6/24 6:30 AM, Roger Quadros wrote:
>>
>>
>> On 05/02/2024 19:34, Andrew Davis wrote:
>>> On 2/5/24 7:59 AM, Roger Quadros wrote:
>>>> There are two USB instances available on the am62p5 starter kit. Include
>>>> and enable them for use on the board.
>>>>
>>>> Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
>>>> Signed-off-by: Roger Quadros <rogerq@kernel.org>
>>>> ---
>>>>
>>>> Notes:
>>>>       Changelog:
>>>>            v4 - no change
>>>>            v3 - no change
>>>>       https://lore.kernel.org/all/20240201120332.4811-4-rogerq@kernel.org/
>>>>            v2:
>>>>       - added USB PHY CTRL node changes here
>>>>       - changed USB wrapper node names to usb@
>>>>       - changed Type-C chip node name to usb-power-control@
>>>>
>>>>    arch/arm64/boot/dts/ti/k3-am62p-main.dtsi   | 46 ++++++++++++++
>>>>    arch/arm64/boot/dts/ti/k3-am62p-wakeup.dtsi | 10 +++
>>>>    arch/arm64/boot/dts/ti/k3-am62p5-sk.dts     | 67 +++++++++++++++++++++
>>>>    3 files changed, 123 insertions(+)
>>>>
>>>> diff --git a/arch/arm64/boot/dts/ti/k3-am62p-main.dtsi b/arch/arm64/boot/dts/ti/k3-am62p-main.dtsi
>>>> index 4c51bae06b57..17d28390d587 100644
>>>> --- a/arch/arm64/boot/dts/ti/k3-am62p-main.dtsi
>>>> +++ b/arch/arm64/boot/dts/ti/k3-am62p-main.dtsi
>>>> @@ -560,6 +560,52 @@ sdhci2: mmc@fa20000 {
>>>>            status = "disabled";
>>>>        };
>>>>    +    usbss0: usb@f900000 {
>>>> +        compatible = "ti,am62-usb";
>>>> +        reg = <0x00 0x0f900000 0x00 0x800>;
>>>> +        clocks = <&k3_clks 161 3>;
>>>> +        clock-names = "ref";
>>>> +        ti,syscon-phy-pll-refclk = <&usb0_phy_ctrl 0x0>;
>>>> +        #address-cells = <2>;
>>>> +        #size-cells = <2>;
>>>> +        power-domains = <&k3_pds 178 TI_SCI_PD_EXCLUSIVE>;
>>>> +        ranges;
>>>> +        status = "disabled";
>>>> +
>>>> +        usb0: usb@31000000 {
>>>> +            compatible = "snps,dwc3";
>>>> +            reg = <0x00 0x31000000 0x00 0x50000>;
>>>> +            interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>, /* irq.0 */
>>>> +            <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>; /* irq.0 */
>>>> +            interrupt-names = "host", "peripheral";
>>>> +            maximum-speed = "high-speed";
>>>> +            dr_mode = "otg";
>>>> +        };
>>>> +    };
>>>> +
>>>> +    usbss1: usb@f910000 {
>>>> +        compatible = "ti,am62-usb";
>>>> +        reg = <0x00 0x0f910000 0x00 0x800>;
>>>> +        clocks = <&k3_clks 162 3>;
>>>> +        clock-names = "ref";
>>>> +        ti,syscon-phy-pll-refclk = <&usb1_phy_ctrl 0x0>;
>>>> +        #address-cells = <2>;
>>>> +        #size-cells = <2>;
>>>> +        power-domains = <&k3_pds 179 TI_SCI_PD_EXCLUSIVE>;
>>>> +        ranges;
>>>> +        status = "disabled";
>>>> +
>>>> +        usb1: usb@31100000 {
>>>> +            compatible = "snps,dwc3";
>>>> +            reg = <0x00 0x31100000 0x00 0x50000>;
>>>> +            interrupts = <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>, /* irq.0 */
>>>> +            <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>; /* irq.0 */
>>>> +            interrupt-names = "host", "peripheral";
>>>> +            maximum-speed = "high-speed";
>>>> +            dr_mode = "otg";
>>>> +        };
>>>> +    };
>>>> +
>>>>        fss: bus@fc00000 {
>>>>            compatible = "simple-bus";
>>>>            reg = <0x00 0x0fc00000 0x00 0x70000>;
>>>> diff --git a/arch/arm64/boot/dts/ti/k3-am62p-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-am62p-wakeup.dtsi
>>>> index 19f42b39394e..00dd38b02a52 100644
>>>> --- a/arch/arm64/boot/dts/ti/k3-am62p-wakeup.dtsi
>>>> +++ b/arch/arm64/boot/dts/ti/k3-am62p-wakeup.dtsi
>>>> @@ -18,6 +18,16 @@ chipid: chipid@14 {
>>>>                reg = <0x14 0x4>;
>>>>                bootph-all;
>>>>            };
>>>> +
>>>> +        usb0_phy_ctrl: syscon@4008 {
>>>> +            compatible = "ti,am62-usb-phy-ctrl", "syscon";
>>>> +            reg = <0x4008 0x4>;
>>>> +        };
>>>> +
>>>> +        usb1_phy_ctrl: syscon@4018 {
>>>> +            compatible = "ti,am62-usb-phy-ctrl", "syscon";
>>>> +            reg = <0x4018 0x4>;
>>>> +        };
>>>>        };
>>>>          wkup_uart0: serial@2b300000 {
>>>> diff --git a/arch/arm64/boot/dts/ti/k3-am62p5-sk.dts b/arch/arm64/boot/dts/ti/k3-am62p5-sk.dts
>>>> index 1773c05f752c..80be56c0a4e0 100644
>>>> --- a/arch/arm64/boot/dts/ti/k3-am62p5-sk.dts
>>>> +++ b/arch/arm64/boot/dts/ti/k3-am62p5-sk.dts
>>>> @@ -27,6 +27,8 @@ aliases {
>>>>            spi0 = &ospi0;
>>>>            ethernet0 = &cpsw_port1;
>>>>            ethernet1 = &cpsw_port2;
>>>> +        usb0 = &usb0;
>>>> +        usb1 = &usb1;
>>>>        };
>>>>          chosen {
>>>> @@ -297,6 +299,12 @@ AM62PX_IOPAD(0x01b0, PIN_OUTPUT, 2) /* (G20) MCASP0_ACLKR.UART1_TXD */
>>>>            bootph-all;
>>>>        };
>>>>    +    main_usb1_pins_default: main-usb1-default-pins {
>>>> +        pinctrl-single,pins = <
>>>> +            AM62PX_IOPAD(0x0258, PIN_INPUT, 0) /* (G21) USB1_DRVVBUS */
>>>> +        >;
>>>> +    };
>>>> +
>>>>        main_wlirq_pins_default: main-wlirq-default-pins {
>>>>            pinctrl-single,pins = <
>>>>                AM62PX_IOPAD(0x0128, PIN_INPUT, 7) /* (K25) MMC2_SDWP.GPIO0_72 */
>>>> @@ -340,6 +348,36 @@ AM62PX_IOPAD(0x0124, PIN_INPUT, 7) /* (J25) MMC2_SDCD.GPIO0_71 */
>>>>        };
>>>>    };
>>>>    +&main_i2c0 {
>>>> +    status = "okay";
>>>> +    pinctrl-names = "default";
>>>> +    pinctrl-0 = <&main_i2c0_pins_default>;
>>>> +    clock-frequency = <400000>;
>>>> +
>>>> +    typec_pd0: usb-power-controller@3f {
>>>> +        compatible = "ti,tps6598x";
>>>> +        reg = <0x3f>;
>>>> +
>>>> +        connector {
>>>> +            compatible = "usb-c-connector";
>>>> +            label = "USB-C";
>>>> +            self-powered;
>>>> +            data-role = "dual";
>>>> +            power-role = "sink";
>>>> +            ports {
>>>> +                #address-cells = <1>;
>>>> +                #size-cells = <0>;
>>>> +                port@0 {
>>>> +                    reg = <0>;
>>>> +                    usb_con_hs: endpoint {
>>>> +                        remote-endpoint = <&usb0_hs_ep>;
>>>> +                    };
>>>> +                };
>>>> +            };
>>>> +        };
>>>> +    };
>>>> +};
>>>> +
>>>>    &main_i2c1 {
>>>>        status = "okay";
>>>>        pinctrl-names = "default";
>>>> @@ -460,6 +498,35 @@ cpsw3g_phy1: ethernet-phy@1 {
>>>>        };
>>>>    };
>>>>    +&usbss0 {
>>>> +    status = "okay";
>>>> +    ti,vbus-divider;
>>>> +};
>>>> +
>>>> +&usbss1 {
>>>> +    status = "okay";
>>>> +    ti,vbus-divider;
>>>> +};
>>>> +
>>>> +&usb0 {
>>>> +    usb-role-switch;
>>>> +    #address-cells = <1>;
>>>> +    #size-cells = <0>;
>>>> +
>>>> +    port@0 {
>>>> +        reg = <0>;
>>>> +        usb0_hs_ep: endpoint {
>>>> +            remote-endpoint = <&usb_con_hs>;
>>>> +        };
>>>> +    };
>>>> +};
>>>> +
>>>> +&usb1 {
>>>> +    dr_mode = "host";
>>>> +    pinctrl-names = "default";
>>>> +    pinctrl-0 = <&main_usb1_pins_default>;
>>>
>>> I'm not super familiar with USB, but I see this pinmux for the
>>> "DRVVBUS" pin is usually added the the parent USB subsystem node (usbss).
>>> Does this pin belong to the subsystem or the specific USB instance?
>>>
>> There is only 1 USB instance per USB sub-system.
>> The "DRVVBUS" pin is a control signal to enable the VBUS regulator
>> while in host mode.
>>
>> Just probing the usbss1 driver has no use of "DRVVBUS".
>> I think usb1 is the right place as it is used there.
>>
> 
> Seems reasonable, so if there ever was more than 1 instance
> per sub-system, each instance would need its own pin?

Yes.

> 
> We should move these pinctrl to the instance node in the other
> dts files at some point then.
> 
> Reviewed-by: Andrew Davis <afd@ti.com>

Thanks!

> 
>>> Andrew
>>>
>>>> +};
>>>> +
>>>>    &mcasp1 {
>>>>        status = "okay";
>>>>        #sound-dai-cells = <0>;
>>

-- 
cheers,
-roger

Re: [PATCH v4 1/3] dt-bindings: mfd: syscon: Add ti,am62-usb-phy-ctrl compatible

[Vignesh Raghavendra]

Hi Roger,

On 05/02/24 19:29, Roger Quadros wrote:
> Add the compatible for TI AM62 USB PHY Control register. This
> register is found in the TI AM62 WKUP_CTRL_MMR0 space [1]. It
> is used to indicate the USB PHY PLL reference clock rate and
> core voltage level to the USB controller.
> 
> [1] - https://www.ti.com/lit/pdf/spruiv7
> 
> Signed-off-by: Roger Quadros <rogerq@kernel.org>
> Acked-by: Rob Herring <robh@kernel.org>
> ---
> 
> Notes:
>     Changelog:
>     
>     v4 - no change. Added Rob's Acked-by
>     
>     v3 - add compatibles in alphabetical order
>     https://lore.kernel.org/all/20240201120332.4811-2-rogerq@kernel.org/
>     
>     v2 - New patch
> 
>  Documentation/devicetree/bindings/mfd/syscon.yaml | 1 +
>  1 file changed, 1 insertion(+)
> 
> diff --git a/Documentation/devicetree/bindings/mfd/syscon.yaml b/Documentation/devicetree/bindings/mfd/syscon.yaml

You don't have right maintainer in CC for this file.

> index 084b5c2a2a3c..9437705af92f 100644
> --- a/Documentation/devicetree/bindings/mfd/syscon.yaml
> +++ b/Documentation/devicetree/bindings/mfd/syscon.yaml
> @@ -72,6 +72,7 @@ properties:
>                - rockchip,rk3588-qos
>                - rockchip,rv1126-qos
>                - starfive,jh7100-sysmain
> +              - ti,am62-usb-phy-ctrl
>                - ti,am654-dss-oldi-io-ctrl
>  
>            - const: syscon

-- 
Regards
Vignesh

Re: [PATCH v4 1/3] dt-bindings: mfd: syscon: Add ti,am62-usb-phy-ctrl compatible

[Roger Quadros]

Hi Vignesh,

On 22/02/2024 10:51, Vignesh Raghavendra wrote:
> Hi Roger,
> 
> On 05/02/24 19:29, Roger Quadros wrote:
>> Add the compatible for TI AM62 USB PHY Control register. This
>> register is found in the TI AM62 WKUP_CTRL_MMR0 space [1]. It
>> is used to indicate the USB PHY PLL reference clock rate and
>> core voltage level to the USB controller.
>>
>> [1] - https://www.ti.com/lit/pdf/spruiv7
>>
>> Signed-off-by: Roger Quadros <rogerq@kernel.org>
>> Acked-by: Rob Herring <robh@kernel.org>
>> ---
>>
>> Notes:
>>     Changelog:
>>     
>>     v4 - no change. Added Rob's Acked-by
>>     
>>     v3 - add compatibles in alphabetical order
>>     https://lore.kernel.org/all/20240201120332.4811-2-rogerq@kernel.org/
>>     
>>     v2 - New patch
>>
>>  Documentation/devicetree/bindings/mfd/syscon.yaml | 1 +
>>  1 file changed, 1 insertion(+)
>>
>> diff --git a/Documentation/devicetree/bindings/mfd/syscon.yaml b/Documentation/devicetree/bindings/mfd/syscon.yaml
> 
> You don't have right maintainer in CC for this file.

I'll resend this series with Acks and updated CC list.

> 
>> index 084b5c2a2a3c..9437705af92f 100644
>> --- a/Documentation/devicetree/bindings/mfd/syscon.yaml
>> +++ b/Documentation/devicetree/bindings/mfd/syscon.yaml
>> @@ -72,6 +72,7 @@ properties:
>>                - rockchip,rk3588-qos
>>                - rockchip,rv1126-qos
>>                - starfive,jh7100-sysmain
>> +              - ti,am62-usb-phy-ctrl
>>                - ti,am654-dss-oldi-io-ctrl
>>  
>>            - const: syscon
> 

-- 
cheers,
-roger