[PATCH v4 00/16] UNI-T UTi260B support

[PATCH v4 00/16] UNI-T UTi260B support

[Sebastian Reichel]

From: Sebastian Reichel <sebastian.reichel@collabora.com>

Hi,

This adds adds support for the UNI-T UTi260B thermal camera, which is based
on i.MX6ULL. Patches 1-14 clean up all warnings reported by CHECK_DTBS for
i.MX6ULL (i.e. for an empty board). They are not specific to the UTi260B and
in fact that machine has most of the IP handled by these patches marked as
disabled. Then patches 15+16 introduce the vendor and board compatible DT
bindings. Finally the last patches adds support for the thermal camera itself.

The DT is based on reverse engineered information. More information about
the device can be found in this presentation from Embedded Recipes 2023:

 * https://embedded-recipes.org/2023/wp-content/uploads/2023/10/Running-FOSS-on-a-Thermal-Camera-Sebastian-Reichel-compressed.pdf
 * https://www.youtube.com/watch?v=uvObsCG-Cqo

I also prepared a branch with these patches (and a minimal kernel config)
and published it here:

https://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-misc.git/log/?h=uti260b-v4

Changes since PATCHv3:
 * https://lore.kernel.org/all/20240216223654.1312880-1-sre@kernel.org/
  - weim binding: use " instead of '
  - weim binding: use "if: not: required: - foo" instead of "if: properties: foo: false"
  - imx6ull-uti260b.dts: merge ecspi3_csgrp into ecspi3grp
  - collect Reviewed-by from Krzysztof Kozlowski

Changes since PATCHv2:
 * https://lore.kernel.org/all/20240213010347.1075251-1-sre@kernel.org/
  - drop fsl,imx-asrc YAML binding conversion (merged)
  - collect a bunch of Reviewed-by/Acked-by tags
  - weim DT binding: fix issue with requirements
  - xnur-gpio -> xnur-gpios change: Improve patch long description

Changes since PATCHv1:
 * https://lore.kernel.org/all/20240210012114.489102-1-sre@kernel.org/
  - uni-t,imx6ull-uti260b -> uni-t,uti260b
  - add Acked-by for uni-t vendor prefix
  - add Acked-by for HDMI audio index fix
  - add Acked-by for LCDIF power-domain requirement drop
  - anatop DT binding: Fixed indentation in example
  - anatop DT binding: Described IRQs
  - touchscreen DT binding: change tsc@ to touchscreen@ in example
  - touchscreen DT binding: change xnur-gpio to xnur-gpios
  - weim DT binding: drop acme,whatever example
  - weim DT binding: use flash@ instead of nor@
  - weim DT binding: update weim.txt reference in arcx,anybus-controller.txt
  - weim DT binding: switch to memory-controller binding
  - fsl,imx-asrc DT binding: fix ASoC patch subject prefix
  - fsl,imx-asrc DT binding: add constraints
  - add new patch fixing xnur-gpio(s) in all i.MX6UL board DT files
  - add new patch fixing touchscreen nodename in i.MX6UL SoC DT file
  - add new patch fixing weim nodename in all i.MX SoC DT files
  - device DTS: use color/functions for the led
  - device DTS: increase SPI speed
  - device DTS: add comment for SD / eMMC node

Unadressed feedback from PATCHv1:
  - anatop phandle vs parent: technically it makes sense to just use the
    parent, but this driver is only used by i.MX6. The current code makes
	use of the phandle, so we cannot drop it because of backwards
	compatibility. So I don't see a point in deprecating this property.
  - touchscreen binding: I kept measure-delay-time and pre-charge-time
    values in hex, since that is being used everywhere and the unit
	is unknown. The values are directly written into HW registers and
	the i.MX6UL TRM does not provide any hints about the unit. I do not
	have an i.MX6UL device with a touchsreen, so I cannot test either.
  - regulator name in DT: I did not rename the regulators to just
    "regulator", since the nodename must be unique.

Greetings,

-- Sebastian

Sebastian Reichel (16):
  dt-bindings: pinctrl: fsl,imx6ul-pinctrl: convert to YAML
  dt-bindings: bus: imx-weim: convert to YAML
  dt-bindings: input: touchscreen: fsl,imx6ul-tsc convert to YAML
  dt-bindings: soc: imx: fsl,imx-anatop: add binding
  dt-bindings: soc: imx: fsl,imx-iomuxc-gpr: add imx6
  dt-bindings: lcdif: Do not require power-domains for i.MX6ULL
  dt-bindings: fsl-imx-sdma: fix HDMI audio index
  ARM: dts: imx6ull: fix pinctrl node name
  ARM: dts: imx6ul: Remove fsl,anatop from usbotg1
  ARM: dts: imx6ul: add missing #thermal-sensor-cells
  ARM: dts: nxp: imx6ul: xnur-gpio -> xnur-gpios
  ARM: dts: nxp: imx6ul: fix touchscreen node name
  ARM: dts: nxp: imx: fix weim node name
  dt-bindings: vendor-prefixes: add UNI-T
  dt-bindings: arm: add UNI-T UTi260B
  ARM: dts: imx6ull-uti260b: Add board

 .../devicetree/bindings/arm/fsl.yaml          |   1 +
 .../devicetree/bindings/bus/imx-weim.txt      | 117 ----
 .../bindings/display/fsl,lcdif.yaml           |   8 +-
 .../devicetree/bindings/dma/fsl,imx-sdma.yaml |   3 +-
 .../input/touchscreen/fsl,imx6ul-tsc.yaml     |  97 +++
 .../bindings/input/touchscreen/imx6ul_tsc.txt |  38 --
 .../fsl/fsl,imx-weim-peripherals.yaml         |  31 +
 .../memory-controllers/fsl/fsl,imx-weim.yaml  | 204 +++++++
 .../mc-peripheral-props.yaml                  |   1 +
 .../bindings/pinctrl/fsl,imx6ul-pinctrl.txt   |  37 --
 .../bindings/pinctrl/fsl,imx6ul-pinctrl.yaml  | 116 ++++
 .../bindings/soc/imx/fsl,imx-anatop.yaml      | 128 ++++
 .../bindings/soc/imx/fsl,imx-iomuxc-gpr.yaml  |  18 +-
 .../devicetree/bindings/vendor-prefixes.yaml  |   2 +
 arch/arm/boot/dts/nxp/imx/Makefile            |   1 +
 arch/arm/boot/dts/nxp/imx/imx1.dtsi           |   2 +-
 arch/arm/boot/dts/nxp/imx/imx27.dtsi          |   2 +-
 arch/arm/boot/dts/nxp/imx/imx31.dtsi          |   2 +-
 arch/arm/boot/dts/nxp/imx/imx35.dtsi          |   2 +-
 arch/arm/boot/dts/nxp/imx/imx51.dtsi          |   2 +-
 arch/arm/boot/dts/nxp/imx/imx6qdl.dtsi        |   2 +-
 arch/arm/boot/dts/nxp/imx/imx6sl.dtsi         |   2 +-
 arch/arm/boot/dts/nxp/imx/imx6sx.dtsi         |   2 +-
 .../boot/dts/nxp/imx/imx6ul-14x14-evk.dtsi    |   2 +-
 arch/arm/boot/dts/nxp/imx/imx6ul-geam.dts     |   2 +-
 .../nxp/imx/imx6ul-imx6ull-opos6uldev.dtsi    |   2 +-
 arch/arm/boot/dts/nxp/imx/imx6ul.dtsi         |   6 +-
 .../boot/dts/nxp/imx/imx6ull-dhcom-som.dtsi   |   2 +-
 arch/arm/boot/dts/nxp/imx/imx6ull-uti260b.dts | 567 ++++++++++++++++++
 arch/arm/boot/dts/nxp/imx/imx6ull.dtsi        |   2 +-
 .../fieldbus/arcx,anybus-controller.txt       |   2 +-
 31 files changed, 1191 insertions(+), 212 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/bus/imx-weim.txt
 create mode 100644 Documentation/devicetree/bindings/input/touchscreen/fsl,imx6ul-tsc.yaml
 delete mode 100644 Documentation/devicetree/bindings/input/touchscreen/imx6ul_tsc.txt
 create mode 100644 Documentation/devicetree/bindings/memory-controllers/fsl/fsl,imx-weim-peripherals.yaml
 create mode 100644 Documentation/devicetree/bindings/memory-controllers/fsl/fsl,imx-weim.yaml
 delete mode 100644 Documentation/devicetree/bindings/pinctrl/fsl,imx6ul-pinctrl.txt
 create mode 100644 Documentation/devicetree/bindings/pinctrl/fsl,imx6ul-pinctrl.yaml
 create mode 100644 Documentation/devicetree/bindings/soc/imx/fsl,imx-anatop.yaml
 create mode 100644 arch/arm/boot/dts/nxp/imx/imx6ull-uti260b.dts

-- 
2.43.0

[PATCH v4 01/16] dt-bindings: pinctrl: fsl,imx6ul-pinctrl: convert to YAML

[Sebastian Reichel]

Convert i.MX6UL pinctrl bindings to YAML.

Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
---
 .../bindings/pinctrl/fsl,imx6ul-pinctrl.txt   |  37 ------
 .../bindings/pinctrl/fsl,imx6ul-pinctrl.yaml  | 116 ++++++++++++++++++
 2 files changed, 116 insertions(+), 37 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/pinctrl/fsl,imx6ul-pinctrl.txt
 create mode 100644 Documentation/devicetree/bindings/pinctrl/fsl,imx6ul-pinctrl.yaml

diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx6ul-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/fsl,imx6ul-pinctrl.txt
deleted file mode 100644
index 7ca4f6118d9a..000000000000
--- a/Documentation/devicetree/bindings/pinctrl/fsl,imx6ul-pinctrl.txt
+++ /dev/null
@@ -1,37 +0,0 @@
-* Freescale i.MX6 UltraLite IOMUX Controller
-
-Please refer to fsl,imx-pinctrl.txt in this directory for common binding part
-and usage.
-
-Required properties:
-- compatible: "fsl,imx6ul-iomuxc" for main IOMUX controller or
-  "fsl,imx6ull-iomuxc-snvs" for i.MX 6ULL's SNVS IOMUX controller.
-- fsl,pins: each entry consists of 6 integers and represents the mux and config
-  setting for one pin.  The first 5 integers <mux_reg conf_reg input_reg mux_val
-  input_val> are specified using a PIN_FUNC_ID macro, which can be found in
-  imx6ul-pinfunc.h under device tree source folder.  The last integer CONFIG is
-  the pad setting value like pull-up on this pin.  Please refer to i.MX6 UltraLite
-  Reference Manual for detailed CONFIG settings.
-
-CONFIG bits definition:
-PAD_CTL_HYS                     (1 << 16)
-PAD_CTL_PUS_100K_DOWN           (0 << 14)
-PAD_CTL_PUS_47K_UP              (1 << 14)
-PAD_CTL_PUS_100K_UP             (2 << 14)
-PAD_CTL_PUS_22K_UP              (3 << 14)
-PAD_CTL_PUE                     (1 << 13)
-PAD_CTL_PKE                     (1 << 12)
-PAD_CTL_ODE                     (1 << 11)
-PAD_CTL_SPEED_LOW               (0 << 6)
-PAD_CTL_SPEED_MED               (1 << 6)
-PAD_CTL_SPEED_HIGH              (3 << 6)
-PAD_CTL_DSE_DISABLE             (0 << 3)
-PAD_CTL_DSE_260ohm              (1 << 3)
-PAD_CTL_DSE_130ohm              (2 << 3)
-PAD_CTL_DSE_87ohm               (3 << 3)
-PAD_CTL_DSE_65ohm               (4 << 3)
-PAD_CTL_DSE_52ohm               (5 << 3)
-PAD_CTL_DSE_43ohm               (6 << 3)
-PAD_CTL_DSE_37ohm               (7 << 3)
-PAD_CTL_SRE_FAST                (1 << 0)
-PAD_CTL_SRE_SLOW                (0 << 0)
diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx6ul-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/fsl,imx6ul-pinctrl.yaml
new file mode 100644
index 000000000000..906b264a9e3c
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx6ul-pinctrl.yaml
@@ -0,0 +1,116 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/fsl,imx6ul-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Freescale IMX6UL IOMUX Controller
+
+maintainers:
+  - Dong Aisheng <aisheng.dong@nxp.com>
+
+description:
+  Please refer to fsl,imx-pinctrl.txt and pinctrl-bindings.txt in this directory
+  for common binding part and usage.
+
+allOf:
+  - $ref: pinctrl.yaml#
+
+properties:
+  compatible:
+    enum:
+      - fsl,imx6ul-iomuxc
+      - fsl,imx6ull-iomuxc-snvs
+
+  reg:
+    maxItems: 1
+
+# Client device subnode's properties
+patternProperties:
+  'grp$':
+    type: object
+    description:
+      Pinctrl node's client devices use subnodes for desired pin configuration.
+      Client device subnodes use below standard properties.
+
+    properties:
+      fsl,pins:
+        description:
+          each entry consists of 6 integers and represents the mux and config
+          setting for one pin. The first 5 integers <mux_reg conf_reg input_reg
+          mux_val input_val> are specified using a PIN_FUNC_ID macro, which can
+          be found in <arch/arm/boot/dts/imx6ul-pinfunc.h>. The last integer
+          CONFIG is the pad setting value like pull-up on this pin. Please
+          refer to i.MX6UL Reference Manual for detailed CONFIG settings.
+        $ref: /schemas/types.yaml#/definitions/uint32-matrix
+        items:
+          items:
+            - description: |
+                "mux_reg" indicates the offset of mux register.
+            - description: |
+                "conf_reg" indicates the offset of pad configuration register.
+            - description: |
+                "input_reg" indicates the offset of select input register.
+            - description: |
+                "mux_val" indicates the mux value to be applied.
+            - description: |
+                "input_val" indicates the select input value to be applied.
+            - description: |
+                "pad_setting" indicates the pad configuration value to be applied:
+                  PAD_CTL_HYS                     (1 << 16)
+                  PAD_CTL_PUS_100K_DOWN           (0 << 14)
+                  PAD_CTL_PUS_47K_UP              (1 << 14)
+                  PAD_CTL_PUS_100K_UP             (2 << 14)
+                  PAD_CTL_PUS_22K_UP              (3 << 14)
+                  PAD_CTL_PUE                     (1 << 13)
+                  PAD_CTL_PKE                     (1 << 12)
+                  PAD_CTL_ODE                     (1 << 11)
+                  PAD_CTL_SPEED_LOW               (0 << 6)
+                  PAD_CTL_SPEED_MED               (1 << 6)
+                  PAD_CTL_SPEED_HIGH              (3 << 6)
+                  PAD_CTL_DSE_DISABLE             (0 << 3)
+                  PAD_CTL_DSE_260ohm              (1 << 3)
+                  PAD_CTL_DSE_130ohm              (2 << 3)
+                  PAD_CTL_DSE_87ohm               (3 << 3)
+                  PAD_CTL_DSE_65ohm               (4 << 3)
+                  PAD_CTL_DSE_52ohm               (5 << 3)
+                  PAD_CTL_DSE_43ohm               (6 << 3)
+                  PAD_CTL_DSE_37ohm               (7 << 3)
+                  PAD_CTL_SRE_FAST                (1 << 0)
+                  PAD_CTL_SRE_SLOW                (0 << 0)
+
+    required:
+      - fsl,pins
+
+    additionalProperties: false
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    iomuxc: pinctrl@20e0000 {
+      compatible = "fsl,imx6ul-iomuxc";
+      reg = <0x020e0000 0x4000>;
+
+      mux_uart: uartgrp {
+        fsl,pins = <
+          0x0084 0x0310 0x0000 0 0 0x1b0b1
+          0x0088 0x0314 0x0624 0 3 0x1b0b1
+        >;
+      };
+    };
+  - |
+    iomuxc_snvs: pinctrl@2290000 {
+      compatible = "fsl,imx6ull-iomuxc-snvs";
+      reg = <0x02290000 0x4000>;
+
+      pinctrl_snvs_usbc_det: snvsusbcdetgrp {
+        fsl,pins = <
+          0x0010 0x0054 0x0000 0x5 0x0 0x130b0
+        >;
+      };
+    };
-- 
2.43.0

[PATCH v4 02/16] dt-bindings: bus: imx-weim: convert to YAML

[Sebastian Reichel]

Convert the i.MX  Wireless External Interface Module binding to YAML.

Signed-off-by: Sebastian Reichel <sre@kernel.org>
---
 .../devicetree/bindings/bus/imx-weim.txt      | 117 ----------
 .../fsl/fsl,imx-weim-peripherals.yaml         |  31 +++
 .../memory-controllers/fsl/fsl,imx-weim.yaml  | 204 ++++++++++++++++++
 .../mc-peripheral-props.yaml                  |   1 +
 .../fieldbus/arcx,anybus-controller.txt       |   2 +-
 5 files changed, 237 insertions(+), 118 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/bus/imx-weim.txt
 create mode 100644 Documentation/devicetree/bindings/memory-controllers/fsl/fsl,imx-weim-peripherals.yaml
 create mode 100644 Documentation/devicetree/bindings/memory-controllers/fsl/fsl,imx-weim.yaml

diff --git a/Documentation/devicetree/bindings/bus/imx-weim.txt b/Documentation/devicetree/bindings/bus/imx-weim.txt
deleted file mode 100644
index e7f502070d77..000000000000
--- a/Documentation/devicetree/bindings/bus/imx-weim.txt
+++ /dev/null
@@ -1,117 +0,0 @@
-Device tree bindings for i.MX Wireless External Interface Module (WEIM)
-
-The term "wireless" does not imply that the WEIM is literally an interface
-without wires. It simply means that this module was originally designed for
-wireless and mobile applications that use low-power technology.
-
-The actual devices are instantiated from the child nodes of a WEIM node.
-
-Required properties:
-
- - compatible:		Should contain one of the following:
-			  "fsl,imx1-weim"
-			  "fsl,imx27-weim"
-			  "fsl,imx51-weim"
-			  "fsl,imx50-weim"
-			  "fsl,imx6q-weim"
- - reg:			A resource specifier for the register space
-			(see the example below)
- - clocks:		the clock, see the example below.
- - #address-cells:	Must be set to 2 to allow memory address translation
- - #size-cells:		Must be set to 1 to allow CS address passing
- - ranges:		Must be set up to reflect the memory layout with four
-			integer values for each chip-select line in use:
-
-			   <cs-number> 0 <physical address of mapping> <size>
-
-Optional properties:
-
- - fsl,weim-cs-gpr:	For "fsl,imx50-weim" and "fsl,imx6q-weim" type of
-			devices, it should be the phandle to the system General
-			Purpose Register controller that contains WEIM CS GPR
-			register, e.g. IOMUXC_GPR1 on i.MX6Q.  IOMUXC_GPR1[11:0]
-			should be set up as one of the following 4 possible
-			values depending on the CS space configuration.
-
-			IOMUXC_GPR1[11:0]    CS0    CS1    CS2    CS3
-			---------------------------------------------
-				05	    128M     0M     0M     0M
-				033          64M    64M     0M     0M
-				0113         64M    32M    32M     0M
-				01111        32M    32M    32M    32M
-
-			In case that the property is absent, the reset value or
-			what bootloader sets up in IOMUXC_GPR1[11:0] will be
-			used.
-
- - fsl,burst-clk-enable	For "fsl,imx50-weim" and "fsl,imx6q-weim" type of
-			devices, the presence of this property indicates that
-			the weim bus should operate in Burst Clock Mode.
-
- - fsl,continuous-burst-clk	Make Burst Clock to output continuous clock.
-			Without this option Burst Clock will output clock
-			only when necessary. This takes effect only if
-			"fsl,burst-clk-enable" is set.
-
-Timing property for child nodes. It is mandatory, not optional.
-
- - fsl,weim-cs-timing:	The timing array, contains timing values for the
-			child node. We get the CS indexes from the address
-			ranges in the child node's "reg" property.
-			The number of registers depends on the selected chip:
-			For i.MX1, i.MX21 ("fsl,imx1-weim") there are two
-			registers: CSxU, CSxL.
-			For i.MX25, i.MX27, i.MX31 and i.MX35 ("fsl,imx27-weim")
-			there are three registers: CSCRxU, CSCRxL, CSCRxA.
-			For i.MX50, i.MX53 ("fsl,imx50-weim"),
-			i.MX51 ("fsl,imx51-weim") and i.MX6Q ("fsl,imx6q-weim")
-			there are six registers: CSxGCR1, CSxGCR2, CSxRCR1,
-			CSxRCR2, CSxWCR1, CSxWCR2.
-
-Example for an imx6q-sabreauto board, the NOR flash connected to the WEIM:
-
-	weim: weim@21b8000 {
-		compatible = "fsl,imx6q-weim";
-		reg = <0x021b8000 0x4000>;
-		clocks = <&clks 196>;
-		#address-cells = <2>;
-		#size-cells = <1>;
-		ranges = <0 0 0x08000000 0x08000000>;
-		fsl,weim-cs-gpr = <&gpr>;
-
-		nor@0,0 {
-			compatible = "cfi-flash";
-			reg = <0 0 0x02000000>;
-			#address-cells = <1>;
-			#size-cells = <1>;
-			bank-width = <2>;
-			fsl,weim-cs-timing = <0x00620081 0x00000001 0x1c022000
-					0x0000c000 0x1404a38e 0x00000000>;
-		};
-	};
-
-Example for an imx6q-based board, a multi-chipselect device connected to WEIM:
-
-In this case, both chip select 0 and 1 will be configured with the same timing
-array values.
-
-	weim: weim@21b8000 {
-		compatible = "fsl,imx6q-weim";
-		reg = <0x021b8000 0x4000>;
-		clocks = <&clks 196>;
-		#address-cells = <2>;
-		#size-cells = <1>;
-		ranges = <0 0 0x08000000 0x02000000
-			  1 0 0x0a000000 0x02000000
-			  2 0 0x0c000000 0x02000000
-			  3 0 0x0e000000 0x02000000>;
-		fsl,weim-cs-gpr = <&gpr>;
-
-		acme@0 {
-			compatible = "acme,whatever";
-			reg = <0 0 0x100>, <0 0x400000 0x800>,
-				<1 0x400000 0x800>;
-			fsl,weim-cs-timing = <0x024400b1 0x00001010 0x20081100
-				0x00000000 0xa0000240 0x00000000>;
-		};
-	};
diff --git a/Documentation/devicetree/bindings/memory-controllers/fsl/fsl,imx-weim-peripherals.yaml b/Documentation/devicetree/bindings/memory-controllers/fsl/fsl,imx-weim-peripherals.yaml
new file mode 100644
index 000000000000..82fc5f4a1ed6
--- /dev/null
+++ b/Documentation/devicetree/bindings/memory-controllers/fsl/fsl,imx-weim-peripherals.yaml
@@ -0,0 +1,31 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/memory-controllers/fsl/fsl,imx-weim-peripherals.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: i.MX WEIM Bus Peripheral Nodes
+
+maintainers:
+  - Shawn Guo <shawnguo@kernel.org>
+  - Sascha Hauer <s.hauer@pengutronix.de>
+
+description:
+  This binding is meant for the child nodes of the WEIM node. The node
+  represents any device connected to the WEIM bus. It may be a Flash chip,
+  RAM chip or Ethernet controller, etc. These properties are meant for
+  configuring the WEIM settings/timings and will accompany the bindings
+  supported by the respective device.
+
+properties:
+  reg: true
+
+  fsl,weim-cs-timing:
+    $ref: /schemas/types.yaml#/definitions/uint32-array
+    description:
+      Timing values for the child node.
+    minItems: 2
+    maxItems: 6
+
+# the WEIM child will have its own native properties
+additionalProperties: true
diff --git a/Documentation/devicetree/bindings/memory-controllers/fsl/fsl,imx-weim.yaml b/Documentation/devicetree/bindings/memory-controllers/fsl/fsl,imx-weim.yaml
new file mode 100644
index 000000000000..3f40ca5b13f6
--- /dev/null
+++ b/Documentation/devicetree/bindings/memory-controllers/fsl/fsl,imx-weim.yaml
@@ -0,0 +1,204 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/memory-controllers/fsl/fsl,imx-weim.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: i.MX Wireless External Interface Module (WEIM)
+
+maintainers:
+  - Shawn Guo <shawnguo@kernel.org>
+  - Sascha Hauer <s.hauer@pengutronix.de>
+
+description:
+  The term "wireless" does not imply that the WEIM is literally an interface
+  without wires. It simply means that this module was originally designed for
+  wireless and mobile applications that use low-power technology. The actual
+  devices are instantiated from the child nodes of a WEIM node.
+
+properties:
+  $nodename:
+    pattern: "^memory-controller@[0-9a-f]+$"
+
+  compatible:
+    oneOf:
+      - enum:
+          - fsl,imx1-weim
+          - fsl,imx27-weim
+          - fsl,imx50-weim
+          - fsl,imx51-weim
+          - fsl,imx6q-weim
+      - items:
+          - enum:
+              - fsl,imx31-weim
+              - fsl,imx35-weim
+          - const: fsl,imx27-weim
+      - items:
+          - enum:
+              - fsl,imx6sx-weim
+              - fsl,imx6ul-weim
+          - const: fsl,imx6q-weim
+
+  "#address-cells":
+    const: 2
+
+  "#size-cells":
+    const: 1
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  ranges: true
+
+  fsl,weim-cs-gpr:
+    $ref: /schemas/types.yaml#/definitions/phandle
+    description: |
+      Phandle to the system General Purpose Register controller that contains
+      WEIM CS GPR register, e.g. IOMUXC_GPR1 on i.MX6Q. IOMUXC_GPR1[11:0]
+      should be set up as one of the following 4 possible values depending on
+      the CS space configuration.
+
+      IOMUXC_GPR1[11:0]    CS0    CS1    CS2    CS3
+      ---------------------------------------------
+              05          128M     0M     0M     0M
+              033          64M    64M     0M     0M
+              0113         64M    32M    32M     0M
+              01111        32M    32M    32M    32M
+
+      In case that the property is absent, the reset value or what bootloader
+      sets up in IOMUXC_GPR1[11:0] will be used.
+
+  fsl,burst-clk-enable:
+    type: boolean
+    description:
+      The presence of this property indicates that the weim bus should operate
+      in Burst Clock Mode.
+
+  fsl,continuous-burst-clk:
+    type: boolean
+    description:
+      Make Burst Clock to output continuous clock. Without this option Burst
+      Clock will output clock only when necessary.
+
+patternProperties:
+  "^.*@[0-7],[0-9a-f]+$":
+    type: object
+    description: Devices attached to chip selects are represented as subnodes.
+    $ref: fsl,imx-weim-peripherals.yaml
+    additionalProperties: true
+    required:
+      - fsl,weim-cs-timing
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - "#address-cells"
+  - "#size-cells"
+  - ranges
+
+allOf:
+  - if:
+      properties:
+        compatible:
+          not:
+            contains:
+              enum:
+                - fsl,imx50-weim
+                - fsl,imx6q-weim
+    then:
+      properties:
+        fsl,weim-cs-gpr: false
+        fsl,burst-clk-enable: false
+  - if:
+      not:
+        required:
+          - fsl,burst-clk-enable
+    then:
+      properties:
+        fsl,continuous-burst-clk: false
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: fsl,imx1-weim
+    then:
+      patternProperties:
+        "^.*@[0-7],[0-9a-f]+$":
+          properties:
+            fsl,weim-cs-timing:
+              items:
+                items:
+                  - description: CSxU
+                  - description: CSxL
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - fsl,imx27-weim
+              - fsl,imx31-weim
+              - fsl,imx35-weim
+    then:
+      patternProperties:
+        "^.*@[0-7],[0-9a-f]+$":
+          properties:
+            fsl,weim-cs-timing:
+              items:
+                items:
+                  - description: CSCRxU
+                  - description: CSCRxL
+                  - description: CSCRxA
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - fsl,imx50-weim
+              - fsl,imx51-weim
+              - fsl,imx6q-weim
+              - fsl,imx6sx-weim
+              - fsl,imx6ul-weim
+    then:
+      patternProperties:
+        "^.*@[0-7],[0-9a-f]+$":
+          properties:
+            fsl,weim-cs-timing:
+              items:
+                items:
+                  - description: CSxGCR1
+                  - description: CSxGCR2
+                  - description: CSxRCR1
+                  - description: CSxRCR2
+                  - description: CSxWCR1
+                  - description: CSxWCR2
+
+additionalProperties: false
+
+examples:
+  - |
+    memory-controller@21b8000 {
+        compatible = "fsl,imx6q-weim";
+        reg = <0x021b8000 0x4000>;
+        clocks = <&clks 196>;
+        #address-cells = <2>;
+        #size-cells = <1>;
+        ranges = <0 0 0x08000000 0x08000000>;
+        fsl,weim-cs-gpr = <&gpr>;
+
+        flash@0,0 {
+            compatible = "cfi-flash";
+            reg = <0 0 0x02000000>;
+            #address-cells = <1>;
+            #size-cells = <1>;
+            bank-width = <2>;
+            fsl,weim-cs-timing = <0x00620081 0x00000001 0x1c022000
+                                  0x0000c000 0x1404a38e 0x00000000>;
+        };
+    };
diff --git a/Documentation/devicetree/bindings/memory-controllers/mc-peripheral-props.yaml b/Documentation/devicetree/bindings/memory-controllers/mc-peripheral-props.yaml
index 8d9dae15ade0..00deeb09f87d 100644
--- a/Documentation/devicetree/bindings/memory-controllers/mc-peripheral-props.yaml
+++ b/Documentation/devicetree/bindings/memory-controllers/mc-peripheral-props.yaml
@@ -37,5 +37,6 @@ allOf:
   - $ref: ingenic,nemc-peripherals.yaml#
   - $ref: intel,ixp4xx-expansion-peripheral-props.yaml#
   - $ref: ti,gpmc-child.yaml#
+  - $ref: fsl/fsl,imx-weim-peripherals.yaml
 
 additionalProperties: true
diff --git a/drivers/staging/fieldbus/Documentation/devicetree/bindings/fieldbus/arcx,anybus-controller.txt b/drivers/staging/fieldbus/Documentation/devicetree/bindings/fieldbus/arcx,anybus-controller.txt
index b1f9474f36d5..f34a95611645 100644
--- a/drivers/staging/fieldbus/Documentation/devicetree/bindings/fieldbus/arcx,anybus-controller.txt
+++ b/drivers/staging/fieldbus/Documentation/devicetree/bindings/fieldbus/arcx,anybus-controller.txt
@@ -48,7 +48,7 @@ Example of usage:
 -----------------
 
 This example places the bridge on top of the i.MX WEIM parallel bus, see:
-Documentation/devicetree/bindings/bus/imx-weim.txt
+Documentation/devicetree/bindings/memory-controllers/fsl/fsl,imx-weim.yaml
 
 &weim {
 	controller@0,0 {
-- 
2.43.0

[PATCH v4 03/16] dt-bindings: input: touchscreen: fsl,imx6ul-tsc convert to YAML

[Sebastian Reichel]

Convert the i.MX6UL touchscreen DT binding to YAML.

Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
---
 .../input/touchscreen/fsl,imx6ul-tsc.yaml     | 97 +++++++++++++++++++
 .../bindings/input/touchscreen/imx6ul_tsc.txt | 38 --------
 2 files changed, 97 insertions(+), 38 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/input/touchscreen/fsl,imx6ul-tsc.yaml
 delete mode 100644 Documentation/devicetree/bindings/input/touchscreen/imx6ul_tsc.txt

diff --git a/Documentation/devicetree/bindings/input/touchscreen/fsl,imx6ul-tsc.yaml b/Documentation/devicetree/bindings/input/touchscreen/fsl,imx6ul-tsc.yaml
new file mode 100644
index 000000000000..678756ad0f92
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/touchscreen/fsl,imx6ul-tsc.yaml
@@ -0,0 +1,97 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/input/touchscreen/fsl,imx6ul-tsc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Freescale i.MX6UL Touch Controller
+
+maintainers:
+  - Haibo Chen <haibo.chen@nxp.com>
+  - Shawn Guo <shawnguo@kernel.org>
+  - Sascha Hauer <s.hauer@pengutronix.de>
+
+properties:
+  compatible:
+    const: fsl,imx6ul-tsc
+
+  reg:
+    items:
+      - description: touch controller address
+      - description: ADC2 address
+
+  interrupts:
+    items:
+      - description: touch controller address
+      - description: ADC2 address
+
+  clocks:
+    maxItems: 2
+
+  clock-names:
+    items:
+      - const: tsc
+      - const: adc
+
+  xnur-gpios:
+    maxItems: 1
+    description:
+      The X- gpio this controller connect to. This xnur-gpio returns to
+      low once the finger leave the touch screen (The last touch event
+      the touch controller capture).
+
+  measure-delay-time:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      The value of measure delay time. Before X-axis or Y-axis measurement,
+      the screen need some time before even potential distribution ready.
+    default: 0xffff
+    minimum: 0
+    maximum: 0xffffff
+
+  pre-charge-time:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      The touch screen need some time to precharge.
+    default: 0xfff
+    minimum: 0
+    maximum: 0xffffffff
+
+  touchscreen-average-samples:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: Number of data samples which are averaged for each read.
+    enum: [ 1, 4, 8, 16, 32 ]
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - clocks
+  - clock-names
+  - xnur-gpios
+
+allOf:
+  - $ref: touchscreen.yaml#
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/clock/imx6ul-clock.h>
+    #include <dt-bindings/gpio/gpio.h>
+    touchscreen@2040000 {
+        compatible = "fsl,imx6ul-tsc";
+        reg = <0x02040000 0x4000>, <0x0219c000 0x4000>;
+        interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
+                     <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
+        clocks = <&clks IMX6UL_CLK_IPG>,
+                 <&clks IMX6UL_CLK_ADC2>;
+        clock-names = "tsc", "adc";
+        pinctrl-names = "default";
+        pinctrl-0 = <&pinctrl_tsc>;
+        xnur-gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
+        measure-delay-time = <0xfff>;
+        pre-charge-time = <0xffff>;
+        touchscreen-average-samples = <32>;
+    };
diff --git a/Documentation/devicetree/bindings/input/touchscreen/imx6ul_tsc.txt b/Documentation/devicetree/bindings/input/touchscreen/imx6ul_tsc.txt
deleted file mode 100644
index 164915004424..000000000000
--- a/Documentation/devicetree/bindings/input/touchscreen/imx6ul_tsc.txt
+++ /dev/null
@@ -1,38 +0,0 @@
-* Freescale i.MX6UL Touch Controller
-
-Required properties:
-- compatible: must be "fsl,imx6ul-tsc".
-- reg: this touch controller address and the ADC2 address.
-- interrupts: the interrupt of this touch controller and ADC2.
-- clocks: the root clock of touch controller and ADC2.
-- clock-names; must be "tsc" and "adc".
-- xnur-gpio: the X- gpio this controller connect to.
-  This xnur-gpio returns to low once the finger leave the touch screen (The
-  last touch event the touch controller capture).
-
-Optional properties:
-- measure-delay-time: the value of measure delay time.
-  Before X-axis or Y-axis measurement, the screen need some time before
-  even potential distribution ready.
-  This value depends on the touch screen.
-- pre-charge-time: the touch screen need some time to precharge.
-  This value depends on the touch screen.
-- touchscreen-average-samples: Number of data samples which are averaged for
-  each read. Valid values are 1, 4, 8, 16 and 32.
-
-Example:
-	tsc: tsc@2040000 {
-		compatible = "fsl,imx6ul-tsc";
-		reg = <0x02040000 0x4000>, <0x0219c000 0x4000>;
-		interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
-			     <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&clks IMX6UL_CLK_IPG>,
-			 <&clks IMX6UL_CLK_ADC2>;
-		clock-names = "tsc", "adc";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_tsc>;
-		xnur-gpio = <&gpio1 3 GPIO_ACTIVE_LOW>;
-		measure-delay-time = <0xfff>;
-		pre-charge-time = <0xffff>;
-		touchscreen-average-samples = <32>;
-	};
-- 
2.43.0

[PATCH v4 04/16] dt-bindings: soc: imx: fsl,imx-anatop: add binding

[Sebastian Reichel]

Add missing binding for i.MX anatop syscon.

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
---
 .../bindings/soc/imx/fsl,imx-anatop.yaml      | 128 ++++++++++++++++++
 1 file changed, 128 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/soc/imx/fsl,imx-anatop.yaml

diff --git a/Documentation/devicetree/bindings/soc/imx/fsl,imx-anatop.yaml b/Documentation/devicetree/bindings/soc/imx/fsl,imx-anatop.yaml
new file mode 100644
index 000000000000..5a59e3470510
--- /dev/null
+++ b/Documentation/devicetree/bindings/soc/imx/fsl,imx-anatop.yaml
@@ -0,0 +1,128 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/soc/imx/fsl,imx-anatop.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: ANATOP register
+
+maintainers:
+  - Shawn Guo <shawnguo@kernel.org>
+  - Sascha Hauer <s.hauer@pengutronix.de>
+
+properties:
+  compatible:
+    oneOf:
+      - items:
+          - enum:
+              - fsl,imx6sl-anatop
+              - fsl,imx6sll-anatop
+              - fsl,imx6sx-anatop
+              - fsl,imx6ul-anatop
+              - fsl,imx7d-anatop
+          - const: fsl,imx6q-anatop
+          - const: syscon
+          - const: simple-mfd
+      - items:
+          - const: fsl,imx6q-anatop
+          - const: syscon
+          - const: simple-mfd
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    items:
+      - description: Temperature sensor event
+      - description: Brown-out event on either of the support regulators
+      - description: Brown-out event on either the core, gpu or soc regulators
+
+  tempmon:
+    type: object
+    unevaluatedProperties: false
+    $ref: /schemas/thermal/imx-thermal.yaml
+
+patternProperties:
+  "regulator-((3p0)|(vddcore)|(vddsoc))$":
+    type: object
+    unevaluatedProperties: false
+    $ref: /schemas/regulator/anatop-regulator.yaml
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/imx6ul-clock.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+    anatop: anatop@20c8000 {
+        compatible = "fsl,imx6ul-anatop", "fsl,imx6q-anatop",
+                     "syscon", "simple-mfd";
+        reg = <0x020c8000 0x1000>;
+        interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>,
+                     <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>,
+                     <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>;
+
+        reg_3p0: regulator-3p0 {
+            compatible = "fsl,anatop-regulator";
+            regulator-name = "vdd3p0";
+            regulator-min-microvolt = <2625000>;
+            regulator-max-microvolt = <3400000>;
+            anatop-reg-offset = <0x120>;
+            anatop-vol-bit-shift = <8>;
+            anatop-vol-bit-width = <5>;
+            anatop-min-bit-val = <0>;
+            anatop-min-voltage = <2625000>;
+            anatop-max-voltage = <3400000>;
+            anatop-enable-bit = <0>;
+        };
+
+        reg_arm: regulator-vddcore {
+            compatible = "fsl,anatop-regulator";
+            regulator-name = "cpu";
+            regulator-min-microvolt = <725000>;
+            regulator-max-microvolt = <1450000>;
+            regulator-always-on;
+            anatop-reg-offset = <0x140>;
+            anatop-vol-bit-shift = <0>;
+            anatop-vol-bit-width = <5>;
+            anatop-delay-reg-offset = <0x170>;
+            anatop-delay-bit-shift = <24>;
+            anatop-delay-bit-width = <2>;
+            anatop-min-bit-val = <1>;
+            anatop-min-voltage = <725000>;
+            anatop-max-voltage = <1450000>;
+        };
+
+        reg_soc: regulator-vddsoc {
+            compatible = "fsl,anatop-regulator";
+            regulator-name = "vddsoc";
+            regulator-min-microvolt = <725000>;
+            regulator-max-microvolt = <1450000>;
+            regulator-always-on;
+            anatop-reg-offset = <0x140>;
+            anatop-vol-bit-shift = <18>;
+            anatop-vol-bit-width = <5>;
+            anatop-delay-reg-offset = <0x170>;
+            anatop-delay-bit-shift = <28>;
+            anatop-delay-bit-width = <2>;
+            anatop-min-bit-val = <1>;
+            anatop-min-voltage = <725000>;
+            anatop-max-voltage = <1450000>;
+        };
+
+        tempmon: tempmon {
+            compatible = "fsl,imx6ul-tempmon", "fsl,imx6sx-tempmon";
+            interrupt-parent = <&gpc>;
+            interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
+            fsl,tempmon = <&anatop>;
+            nvmem-cells = <&tempmon_calib>, <&tempmon_temp_grade>;
+            nvmem-cell-names = "calib", "temp_grade";
+            clocks = <&clks IMX6UL_CLK_PLL3_USB_OTG>;
+            #thermal-sensor-cells = <0>;
+        };
+    };
-- 
2.43.0

[PATCH v4 05/16] dt-bindings: soc: imx: fsl,imx-iomuxc-gpr: add imx6

[Sebastian Reichel]

Add compatibles used by different i.MX6 variants to the i.MX IOMUX
Controller GPR binding.

Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
---
 .../bindings/soc/imx/fsl,imx-iomuxc-gpr.yaml   | 18 +++++++++++++++++-
 1 file changed, 17 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/soc/imx/fsl,imx-iomuxc-gpr.yaml b/Documentation/devicetree/bindings/soc/imx/fsl,imx-iomuxc-gpr.yaml
index 1da1b758b4ae..8451cb4dd87c 100644
--- a/Documentation/devicetree/bindings/soc/imx/fsl,imx-iomuxc-gpr.yaml
+++ b/Documentation/devicetree/bindings/soc/imx/fsl,imx-iomuxc-gpr.yaml
@@ -17,7 +17,23 @@ properties:
   compatible:
     oneOf:
       - items:
-          - const: fsl,imx8mq-iomuxc-gpr
+          - enum:
+              - fsl,imx6q-iomuxc-gpr
+              - fsl,imx8mq-iomuxc-gpr
+          - const: syscon
+          - const: simple-mfd
+      - items:
+          - enum:
+              - fsl,imx6sl-iomuxc-gpr
+              - fsl,imx6sll-iomuxc-gpr
+              - fsl,imx6ul-iomuxc-gpr
+          - const: fsl,imx6q-iomuxc-gpr
+          - const: syscon
+      - items:
+          - enum:
+              - fsl,imx6sx-iomuxc-gpr
+              - fsl,imx7d-iomuxc-gpr
+          - const: fsl,imx6q-iomuxc-gpr
           - const: syscon
           - const: simple-mfd
       - items:
-- 
2.43.0

[PATCH v4 06/16] dt-bindings: lcdif: Do not require power-domains for i.MX6ULL

[Sebastian Reichel]

i.MX6UL(L) uses "fsl,imx6sx-lcdif" as fallback compatible string,
but has only very lightweight DISPLAY power domain. Its DISPLAY
power domain is not supported by the binding / Linux kernel at
the moment. Since the current setup is working, let's remove the
power-domain from being required for that platform to fix the warning
printed by CHECK_DTBS=y.

Fixes: f62678a77d58 ("dt-bindings: mxsfb: Document i.MX8M/i.MX6SX/i.MX6SL power-domains property")
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
---
 Documentation/devicetree/bindings/display/fsl,lcdif.yaml | 8 +++++++-
 1 file changed, 7 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/display/fsl,lcdif.yaml b/Documentation/devicetree/bindings/display/fsl,lcdif.yaml
index 1c2be8d6f633..0681fc49aa1b 100644
--- a/Documentation/devicetree/bindings/display/fsl,lcdif.yaml
+++ b/Documentation/devicetree/bindings/display/fsl,lcdif.yaml
@@ -120,13 +120,19 @@ allOf:
           maxItems: 1
         clock-names:
           maxItems: 1
+  - if:
+      properties:
+        compatible:
+          const: fsl,imx6sx-lcdif
+    then:
+      required:
+        - power-domains
   - if:
       properties:
         compatible:
           contains:
             enum:
               - fsl,imx6sl-lcdif
-              - fsl,imx6sx-lcdif
               - fsl,imx8mm-lcdif
               - fsl,imx8mn-lcdif
               - fsl,imx8mp-lcdif
-- 
2.43.0

[PATCH v4 07/16] dt-bindings: fsl-imx-sdma: fix HDMI audio index

[Sebastian Reichel]

HDMI Audio has been added to the DT binding documentation with an
incorrect index. DT and the driver use index 26. This happened,
because the binding is missing MULTI_SAI type, which is using
index 25.

Reported-by: Michael Yackavage <michaely@ips-yes.com>
Fixes: 7bdbd87d4008 ("dt-bindings: fsl-imx-sdma: Convert imx sdma to DT schema")
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
---
 Documentation/devicetree/bindings/dma/fsl,imx-sdma.yaml | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/dma/fsl,imx-sdma.yaml b/Documentation/devicetree/bindings/dma/fsl,imx-sdma.yaml
index b95dd8db5a30..37135fa024f9 100644
--- a/Documentation/devicetree/bindings/dma/fsl,imx-sdma.yaml
+++ b/Documentation/devicetree/bindings/dma/fsl,imx-sdma.yaml
@@ -92,7 +92,8 @@ properties:
               description: needs firmware more than ver 2
           - Shared ASRC: 23
           - SAI: 24
-          - HDMI Audio: 25
+          - Multi SAI: 25
+          - HDMI Audio: 26
 
        The third cell: transfer priority ID
          enum:
-- 
2.43.0

[PATCH v4 08/16] ARM: dts: imx6ull: fix pinctrl node name

[Sebastian Reichel]

pinctrl node name must be either pinctrl or pinmux.

Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
---
 arch/arm/boot/dts/nxp/imx/imx6ull.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ull.dtsi
index 2bccd45e9fc2..8a1776067ecc 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6ull.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull.dtsi
@@ -75,7 +75,7 @@ rngb: rng@2284000 {
 				clocks = <&clks IMX6UL_CLK_DUMMY>;
 			};
 
-			iomuxc_snvs: iomuxc-snvs@2290000 {
+			iomuxc_snvs: pinctrl@2290000 {
 				compatible = "fsl,imx6ull-iomuxc-snvs";
 				reg = <0x02290000 0x4000>;
 			};
-- 
2.43.0

[PATCH v4 09/16] ARM: dts: imx6ul: Remove fsl,anatop from usbotg1

[Sebastian Reichel]

fsl,anatop should only be added to the usbphy nodes.

Signed-off-by: Sebastian Reichel <sre@kernel.org>
---
 arch/arm/boot/dts/nxp/imx/imx6ul.dtsi | 1 -
 1 file changed, 1 deletion(-)

diff --git a/arch/arm/boot/dts/nxp/imx/imx6ul.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul.dtsi
index a27a7554c2e7..9eb4eee0c272 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6ul.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul.dtsi
@@ -855,7 +855,6 @@ usbotg1: usb@2184000 {
 				clocks = <&clks IMX6UL_CLK_USBOH3>;
 				fsl,usbphy = <&usbphy1>;
 				fsl,usbmisc = <&usbmisc 0>;
-				fsl,anatop = <&anatop>;
 				ahb-burst-config = <0x0>;
 				tx-burst-size-dword = <0x10>;
 				rx-burst-size-dword = <0x10>;
-- 
2.43.0

[PATCH v4 10/16] ARM: dts: imx6ul: add missing #thermal-sensor-cells

[Sebastian Reichel]

Fix the following warning found via CHECK_DTBS:

tempmon: '#thermal-sensor-cells' is a required property

Signed-off-by: Sebastian Reichel <sre@kernel.org>
---
 arch/arm/boot/dts/nxp/imx/imx6ul.dtsi | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm/boot/dts/nxp/imx/imx6ul.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul.dtsi
index 9eb4eee0c272..45b7605ac381 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6ul.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul.dtsi
@@ -638,6 +638,7 @@ tempmon: tempmon {
 					nvmem-cells = <&tempmon_calib>, <&tempmon_temp_grade>;
 					nvmem-cell-names = "calib", "temp_grade";
 					clocks = <&clks IMX6UL_CLK_PLL3_USB_OTG>;
+					#thermal-sensor-cells = <0>;
 				};
 			};
 
-- 
2.43.0

[PATCH v4 11/16] ARM: dts: nxp: imx6ul: xnur-gpio -> xnur-gpios

[Sebastian Reichel]

Replace all "xnur-gpio" with "xnur-gpios" in the i.MX6UL(L) Touchscreen
node, since the -gpio suffix is deprecated. All known implementations of
this binding can handle -gpio and -gpios since day 1, so this should be
fully backwards compatible.

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
---
 arch/arm/boot/dts/nxp/imx/imx6ul-14x14-evk.dtsi          | 2 +-
 arch/arm/boot/dts/nxp/imx/imx6ul-geam.dts                | 2 +-
 arch/arm/boot/dts/nxp/imx/imx6ul-imx6ull-opos6uldev.dtsi | 2 +-
 arch/arm/boot/dts/nxp/imx/imx6ull-dhcom-som.dtsi         | 2 +-
 4 files changed, 4 insertions(+), 4 deletions(-)

diff --git a/arch/arm/boot/dts/nxp/imx/imx6ul-14x14-evk.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul-14x14-evk.dtsi
index 2ac40d69425b..f10f0525490b 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6ul-14x14-evk.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-14x14-evk.dtsi
@@ -321,7 +321,7 @@ &snvs_pwrkey {
 &tsc {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_tsc>;
-	xnur-gpio = <&gpio1 3 GPIO_ACTIVE_LOW>;
+	xnur-gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
 	measure-delay-time = <0xffff>;
 	pre-charge-time = <0xfff>;
 	status = "okay";
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ul-geam.dts b/arch/arm/boot/dts/nxp/imx/imx6ul-geam.dts
index 875ae699c5cb..2ca18f3dad0a 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6ul-geam.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-geam.dts
@@ -203,7 +203,7 @@ &pwm8 {
 &tsc {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_tsc>;
-	xnur-gpio = <&gpio1 3 GPIO_ACTIVE_LOW>;
+	xnur-gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
 };
 
 &sai2 {
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ul-imx6ull-opos6uldev.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul-imx6ull-opos6uldev.dtsi
index 18cac19aa9b0..af337f18a266 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6ul-imx6ull-opos6uldev.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul-imx6ull-opos6uldev.dtsi
@@ -156,7 +156,7 @@ &snvs_pwrkey {
 &tsc {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_tsc>;
-	xnur-gpio = <&gpio1 3 GPIO_ACTIVE_LOW>;
+	xnur-gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
 	measure-delay-time = <0xffff>;
 	pre-charge-time = <0xffff>;
 	status = "okay";
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-dhcom-som.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ull-dhcom-som.dtsi
index 830b5a5064f2..6d2163250b5d 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6ull-dhcom-som.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-dhcom-som.dtsi
@@ -273,7 +273,7 @@ &tsc {
 	pinctrl-names = "default";
 	pre-charge-time = <0xfff>;
 	touchscreen-average-samples = <32>;
-	xnur-gpio = <&gpio1 3 GPIO_ACTIVE_LOW>;
+	xnur-gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
 };
 
 /* DHCOM UART1 */
-- 
2.43.0

[PATCH v4 12/16] ARM: dts: nxp: imx6ul: fix touchscreen node name

[Sebastian Reichel]

The canonical node name for touchscreens is "touchscreen",
so update the i.MX6UL "tsc" node accordingly.

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
---
 arch/arm/boot/dts/nxp/imx/imx6ul.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/nxp/imx/imx6ul.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul.dtsi
index 45b7605ac381..8aa365f837ca 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6ul.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul.dtsi
@@ -370,7 +370,7 @@ asrc: asrc@2034000 {
 				};
 			};
 
-			tsc: tsc@2040000 {
+			tsc: touchscreen@2040000 {
 				compatible = "fsl,imx6ul-tsc";
 				reg = <0x02040000 0x4000>, <0x0219c000 0x4000>;
 				interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
-- 
2.43.0

[PATCH v4 13/16] ARM: dts: nxp: imx: fix weim node name

[Sebastian Reichel]

DT node names should be generic, so replace "weim" node name with
"memory-controller" in all i.MX SoC DT files.

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
---
 arch/arm/boot/dts/nxp/imx/imx1.dtsi    | 2 +-
 arch/arm/boot/dts/nxp/imx/imx27.dtsi   | 2 +-
 arch/arm/boot/dts/nxp/imx/imx31.dtsi   | 2 +-
 arch/arm/boot/dts/nxp/imx/imx35.dtsi   | 2 +-
 arch/arm/boot/dts/nxp/imx/imx51.dtsi   | 2 +-
 arch/arm/boot/dts/nxp/imx/imx6qdl.dtsi | 2 +-
 arch/arm/boot/dts/nxp/imx/imx6sl.dtsi  | 2 +-
 arch/arm/boot/dts/nxp/imx/imx6sx.dtsi  | 2 +-
 arch/arm/boot/dts/nxp/imx/imx6ul.dtsi  | 2 +-
 9 files changed, 9 insertions(+), 9 deletions(-)

diff --git a/arch/arm/boot/dts/nxp/imx/imx1.dtsi b/arch/arm/boot/dts/nxp/imx/imx1.dtsi
index 1ac10965fdfd..389ecb1ebf8f 100644
--- a/arch/arm/boot/dts/nxp/imx/imx1.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx1.dtsi
@@ -251,7 +251,7 @@ gpio4: gpio@21c300 {
 			};
 		};
 
-		weim: weim@220000 {
+		weim: memory-controller@220000 {
 			#address-cells = <2>;
 			#size-cells = <1>;
 			compatible = "fsl,imx1-weim";
diff --git a/arch/arm/boot/dts/nxp/imx/imx27.dtsi b/arch/arm/boot/dts/nxp/imx/imx27.dtsi
index ec472695c71e..ec3ccc8f4095 100644
--- a/arch/arm/boot/dts/nxp/imx/imx27.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx27.dtsi
@@ -568,7 +568,7 @@ nfc: nand-controller@d8000000 {
 			status = "disabled";
 		};
 
-		weim: weim@d8002000 {
+		weim: memory-controller@d8002000 {
 			#address-cells = <2>;
 			#size-cells = <1>;
 			compatible = "fsl,imx27-weim";
diff --git a/arch/arm/boot/dts/nxp/imx/imx31.dtsi b/arch/arm/boot/dts/nxp/imx/imx31.dtsi
index e1ae7c175f7d..00006c90d9a7 100644
--- a/arch/arm/boot/dts/nxp/imx/imx31.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx31.dtsi
@@ -352,7 +352,7 @@ nfc: nand@b8000000 {
 				status = "disabled";
 			};
 
-			weim: weim@b8002000 {
+			weim: memory-controller@b8002000 {
 				compatible = "fsl,imx31-weim", "fsl,imx27-weim";
 				reg = <0xb8002000 0x1000>;
 				clocks = <&clks 56>;
diff --git a/arch/arm/boot/dts/nxp/imx/imx35.dtsi b/arch/arm/boot/dts/nxp/imx/imx35.dtsi
index 2d20e5541acc..442dc15677b8 100644
--- a/arch/arm/boot/dts/nxp/imx/imx35.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx35.dtsi
@@ -374,7 +374,7 @@ nfc: nand@bb000000 {
 				status = "disabled";
 			};
 
-			weim: weim@b8002000 {
+			weim: memory-controller@b8002000 {
 				#address-cells = <2>;
 				#size-cells = <1>;
 				clocks = <&clks 0>;
diff --git a/arch/arm/boot/dts/nxp/imx/imx51.dtsi b/arch/arm/boot/dts/nxp/imx/imx51.dtsi
index c96d6311dfa7..4efce49022e4 100644
--- a/arch/arm/boot/dts/nxp/imx/imx51.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx51.dtsi
@@ -578,7 +578,7 @@ m4if: m4if@83fd8000 {
 				reg = <0x83fd8000 0x1000>;
 			};
 
-			weim: weim@83fda000 {
+			weim: memory-controller@83fda000 {
 				#address-cells = <2>;
 				#size-cells = <1>;
 				compatible = "fsl,imx51-weim";
diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl.dtsi b/arch/arm/boot/dts/nxp/imx/imx6qdl.dtsi
index 81142c523fa8..8431b8a994f4 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6qdl.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6qdl.dtsi
@@ -1158,7 +1158,7 @@ mmdc1: memory-controller@21b4000 { /* MMDC1 */
 				status = "disabled";
 			};
 
-			weim: weim@21b8000 {
+			weim: memory-controller@21b8000 {
 				#address-cells = <2>;
 				#size-cells = <1>;
 				compatible = "fsl,imx6q-weim";
diff --git a/arch/arm/boot/dts/nxp/imx/imx6sl.dtsi b/arch/arm/boot/dts/nxp/imx/imx6sl.dtsi
index 28111efb19a6..6aa61235e39e 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6sl.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6sl.dtsi
@@ -949,7 +949,7 @@ rngb: rngb@21b4000 {
 				clocks = <&clks IMX6SL_CLK_DUMMY>;
 			};
 
-			weim: weim@21b8000 {
+			weim: memory-controller@21b8000 {
 				#address-cells = <2>;
 				#size-cells = <1>;
 				reg = <0x021b8000 0x4000>;
diff --git a/arch/arm/boot/dts/nxp/imx/imx6sx.dtsi b/arch/arm/boot/dts/nxp/imx/imx6sx.dtsi
index df3a375f0a3e..0de359d62a47 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6sx.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6sx.dtsi
@@ -1107,7 +1107,7 @@ fec2: ethernet@21b4000 {
 				status = "disabled";
 			};
 
-			weim: weim@21b8000 {
+			weim: memory-controller@21b8000 {
 				#address-cells = <2>;
 				#size-cells = <1>;
 				compatible = "fsl,imx6sx-weim", "fsl,imx6q-weim";
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ul.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul.dtsi
index 8aa365f837ca..aeb7e07fd309 100644
--- a/arch/arm/boot/dts/nxp/imx/imx6ul.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx6ul.dtsi
@@ -975,7 +975,7 @@ memory-controller@21b0000 {
 				clocks = <&clks IMX6UL_CLK_MMDC_P0_IPG>;
 			};
 
-			weim: weim@21b8000 {
+			weim: memory-controller@21b8000 {
 				#address-cells = <2>;
 				#size-cells = <1>;
 				compatible = "fsl,imx6ul-weim", "fsl,imx6q-weim";
-- 
2.43.0

[PATCH v4 14/16] dt-bindings: vendor-prefixes: add UNI-T

[Sebastian Reichel]

Uni-Trend Technology is a manufacturer of measurement
and testing tools.

Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
---
 Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index 1a0dc04f1db4..e945e76696c2 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -1484,6 +1484,8 @@ patternProperties:
     description: Ufi Space Co., Ltd.
   "^ugoos,.*":
     description: Ugoos Industrial Co., Ltd.
+  "^uni-t,.*":
+    description: Uni-Trend Technology (China) Co., Ltd.
   "^uniwest,.*":
     description: United Western Technologies Corp (UniWest)
   "^upisemi,.*":
-- 
2.43.0

[PATCH v4 15/16] dt-bindings: arm: add UNI-T UTi260B

[Sebastian Reichel]

Add compatible value for i.MX6ULL based UNI-T UTi260B thermal camera.

Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
---
 Documentation/devicetree/bindings/arm/fsl.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index 228dcc5c7d6f..7b65f9c9c1a5 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -708,6 +708,7 @@ properties:
               - toradex,colibri-imx6ull      # Colibri iMX6ULL Modules
               - toradex,colibri-imx6ull-emmc # Colibri iMX6ULL 1GB (eMMC) Module
               - toradex,colibri-imx6ull-wifi # Colibri iMX6ULL Wi-Fi / BT Modules
+              - uni-t,uti260b             # UNI-T UTi260B Thermal Camera
           - const: fsl,imx6ull
 
       - description: i.MX6ULL Armadeus Systems OPOS6ULDev Board
-- 
2.43.0

[PATCH v4 16/16] ARM: dts: imx6ull-uti260b: Add board

[Sebastian Reichel]

Add UNI-T UTi260b thermal camera board.

Reviewed-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
---
 arch/arm/boot/dts/nxp/imx/Makefile            |   1 +
 arch/arm/boot/dts/nxp/imx/imx6ull-uti260b.dts | 567 ++++++++++++++++++
 2 files changed, 568 insertions(+)
 create mode 100644 arch/arm/boot/dts/nxp/imx/imx6ull-uti260b.dts

diff --git a/arch/arm/boot/dts/nxp/imx/Makefile b/arch/arm/boot/dts/nxp/imx/Makefile
index a724d1a7a9a0..47350cf3ddeb 100644
--- a/arch/arm/boot/dts/nxp/imx/Makefile
+++ b/arch/arm/boot/dts/nxp/imx/Makefile
@@ -349,6 +349,7 @@ dtb-$(CONFIG_SOC_IMX6UL) += \
 	imx6ull-tarragon-slavext.dtb \
 	imx6ull-tqma6ull2-mba6ulx.dtb \
 	imx6ull-tqma6ull2l-mba6ulx.dtb \
+	imx6ull-uti260b.dtb \
 	imx6ulz-14x14-evk.dtb \
 	imx6ulz-bsh-smm-m2.dtb
 dtb-$(CONFIG_SOC_IMX7D) += \
diff --git a/arch/arm/boot/dts/nxp/imx/imx6ull-uti260b.dts b/arch/arm/boot/dts/nxp/imx/imx6ull-uti260b.dts
new file mode 100644
index 000000000000..8f6f092363b7
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/imx/imx6ull-uti260b.dts
@@ -0,0 +1,567 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+// Copyright (C) 2022-2024 Sebastian Reichel <sre@kernel.org>
+
+/dts-v1/;
+#include "imx6ull.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/clock/imx6ul-clock.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	model = "UNI-T UTi260B Thermal Camera";
+	compatible = "uni-t,uti260b", "fsl,imx6ull";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x20000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&mux_led_ctrl>;
+
+		led {
+			color = <LED_COLOR_ID_WHITE>;
+			function = LED_FUNCTION_FLASH;
+			gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&mux_gpio_keys>;
+		autorepeat;
+
+		up-key {
+			label = "Up";
+			gpios = <&gpio2 11 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_UP>;
+		};
+
+		down-key {
+			label = "Down";
+			gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_DOWN>;
+		};
+
+		left-key {
+			label = "Left";
+			gpios = <&gpio2 13 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_LEFT>;
+		};
+
+		right-key {
+			label = "Right";
+			gpios = <&gpio2 10 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RIGHT>;
+		};
+
+		ok-key {
+			label = "Ok";
+			gpios = <&gpio2 9 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_ENTER>;
+		};
+
+		return-key {
+			label = "Return";
+			gpios = <&gpio2 15 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_ESC>;
+		};
+
+		play-key {
+			label = "Media";
+			gpios = <&gpio2 8 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_MEDIA>;
+		};
+
+		trigger-key {
+			label = "Trigger";
+			gpios = <&gpio2 14 GPIO_ACTIVE_LOW>;
+			linux,code = <BTN_TRIGGER>;
+		};
+
+		power-key {
+			label = "Power";
+			gpios = <&gpio2 3 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_POWER>;
+		};
+
+		light-key {
+			label = "Light";
+			gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_LIGHTS_TOGGLE>;
+		};
+	};
+
+	panel_backlight: backlight {
+		compatible = "pwm-backlight";
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <6>;
+		enable-gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&mux_backlight_enable>;
+		power-supply = <&reg_vsd>;
+		pwms = <&pwm1 0 50000 0>;
+	};
+
+	reg_vsd: regulator-vsd {
+		compatible = "regulator-fixed";
+		regulator-name = "VSD_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_vref: regulator-vref-4v2 {
+		compatible = "regulator-fixed";
+		regulator-name = "VREF_4V2";
+		regulator-min-microvolt = <4200000>;
+		regulator-max-microvolt = <4200000>;
+	};
+
+	tp5000: charger {
+		compatible = "gpio-charger";
+		charger-type = "usb-sdp";
+		gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&mux_charger_stat1>;
+	};
+
+	battery: battery {
+		compatible = "simple-battery";
+		/* generic 26650 battery */
+		device-chemistry = "lithium-ion";
+		charge-full-design-microamp-hours = <5000000>;
+		voltage-max-design-microvolt = <4200000>;
+		voltage-min-design-microvolt = <3300000>;
+	};
+
+	fuel-gauge {
+		compatible = "adc-battery";
+		charged-gpios = <&gpio1 2 GPIO_ACTIVE_LOW>;
+		io-channel-names = "voltage";
+		io-channels = <&adc1 7>;
+		monitored-battery = <&battery>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&mux_charger_stat2>;
+		power-supplies = <&tp5000>;
+	};
+
+	poweroff {
+		compatible = "gpio-poweroff";
+		gpios = <&gpio2 4 GPIO_ACTIVE_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&mux_poweroff>;
+	};
+};
+
+&gpio1 {
+	ir-reset-hog {
+		gpio-hog;
+		gpios = <3 GPIO_ACTIVE_LOW>;
+		line-name = "ir-reset-gpio";
+		output-low;
+		pinctrl-names = "default";
+		pinctrl-0 = <&mux_ir_reset>;
+	};
+};
+
+&gpio2 {
+	/* configuring this to output-high results in poweroff */
+	power-en-hog {
+		gpio-hog;
+		gpios = <6 GPIO_ACTIVE_HIGH>;
+		line-name = "power-en-gpio";
+		output-low;
+		pinctrl-names = "default";
+		pinctrl-0 = <&mux_poweroff2>;
+	};
+};
+
+&ecspi3 {
+	cs-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mux_spi3>;
+	status = "okay";
+
+	panel@0 {
+		compatible = "inanbo,t28cp45tn89-v17";
+		reg = <0>;
+		backlight = <&panel_backlight>;
+		power-supply = <&reg_vsd>;
+		spi-cpha;
+		spi-cpol;
+		spi-max-frequency = <1000000>;
+		spi-rx-bus-width = <0>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&display_out>;
+			};
+		};
+	};
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mux_uart>;
+	status = "okay";
+};
+
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mux_pwm>;
+	status = "okay";
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mux_i2c1>;
+	status = "okay";
+
+	camera@21 {
+		compatible = "galaxycore,gc0308";
+		reg = <0x21>;
+		clocks = <&clks IMX6UL_CLK_CSI>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&mux_gc0308>;
+		powerdown-gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>;
+		reset-gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
+		vdd28-supply = <&reg_vsd>;
+
+		port {
+			gc0308_to_parallel: endpoint {
+				remote-endpoint = <&parallel_from_gc0308>;
+				bus-width = <8>;
+				data-shift = <2>; /* lines 9:2 are used */
+				hsync-active = <1>; /* active high */
+				vsync-active = <1>; /* active high */
+				data-active = <1>; /* active high */
+				pclk-sample = <1>; /* sample on rising edge */
+			};
+		};
+	};
+};
+
+&csi {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mux_csi>;
+
+	port {
+		parallel_from_gc0308: endpoint {
+			remote-endpoint = <&gc0308_to_parallel>;
+		};
+	};
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mux_i2c2>;
+	status = "okay";
+
+	rtc@51 {
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+	};
+};
+
+&lcdif {
+	assigned-clocks = <&clks IMX6UL_CLK_LCDIF_PRE_SEL>;
+	assigned-clock-parents = <&clks IMX6UL_CLK_PLL5_VIDEO_DIV>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mux_lcd_data>, <&mux_lcd_ctrl>;
+	status = "okay";
+
+	port {
+		display_out: endpoint {
+			remote-endpoint = <&panel_in>;
+		};
+	};
+};
+
+&usdhc1 {
+	/* MicroSD */
+	cd-gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
+	keep-power-in-suspend;
+	no-1-8-v;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&mux_sdhc1>, <&mux_sdhc1_cd>;
+	pinctrl-1 = <&mux_sdhc1_100mhz>, <&mux_sdhc1_cd>;
+	pinctrl-2 = <&mux_sdhc1_200mhz>, <&mux_sdhc1_cd>;
+	wakeup-source;
+	vmmc-supply = <&reg_vsd>;
+	status = "okay";
+};
+
+&usdhc2 {
+	/* eMMC */
+	keep-power-in-suspend;
+	no-1-8-v;
+	non-removable;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mux_sdhc2>;
+	wakeup-source;
+	status = "okay";
+};
+
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mux_wdog>;
+};
+
+&adc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mux_adc>;
+	vref-supply = <&reg_vref>;
+	#io-channel-cells = <1>;
+	status = "okay";
+};
+
+&usbotg1 {
+	/* USB-C connector */
+	disable-over-current;
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usbotg2 {
+	/* thermal sensor */
+	disable-over-current;
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usbphy1 {
+	fsl,tx-d-cal = <106>;
+};
+
+&usbphy2 {
+	fsl,tx-d-cal = <106>;
+};
+
+&iomuxc {
+	mux_ir_reset: irresetgrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO03__GPIO1_IO03		0x3008
+		>;
+	};
+
+	mux_poweroff: poweroffgrp {
+		fsl,pins = <
+			MX6UL_PAD_ENET1_TX_DATA1__GPIO2_IO04		0x3008
+		>;
+	};
+
+	mux_poweroff2: poweroff2grp {
+		fsl,pins = <
+			MX6UL_PAD_ENET1_TX_CLK__GPIO2_IO06		0x3008
+		>;
+	};
+
+	mux_charger_stat1: charger1grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO01__GPIO1_IO01		0x3008
+		>;
+	};
+
+	mux_charger_stat2: charger2grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO02__GPIO1_IO02		0x3008
+		>;
+	};
+
+	mux_wdog: wdoggrp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_RESET__WDOG1_WDOG_ANY		0x30b0
+		>;
+	};
+
+	mux_sdhc1_cd: sdhc1-cd-grp {
+		fsl,pins = <
+			MX6UL_PAD_UART1_RTS_B__GPIO1_IO19		0x17059
+		>;
+	};
+
+	mux_sdhc1: sdhc1grp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD			0x17059
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK			0x10071
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0		0x17059
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1		0x17059
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2		0x17059
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3		0x17059
+		>;
+	};
+
+	mux_sdhc1_100mhz: sdhc1-100mhz-grp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD			0x170b9
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK			0x170b9
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0		0x170b9
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1		0x170b9
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2		0x170b9
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3		0x170b9
+		>;
+	};
+
+	mux_sdhc1_200mhz: sdhc1-200mhz-grp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD			0x170f9
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK			0x170f9
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0		0x170f9
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1		0x170f9
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2		0x170f9
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3		0x170f9
+		>;
+	};
+
+	mux_sdhc2: sdhc2grp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK			0x10069
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD			0x17059
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0		0x17059
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1		0x17059
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2		0x17059
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3		0x17059
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4		0x17059
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5		0x17059
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6		0x17059
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7		0x17059
+		>;
+	};
+
+	mux_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6UL_PAD_UART4_TX_DATA__I2C1_SCL		0x4001b8b0
+			MX6UL_PAD_UART4_RX_DATA__I2C1_SDA		0x4001b8b0
+		>;
+	};
+
+	mux_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6UL_PAD_UART5_TX_DATA__I2C2_SCL		0x4001f8a8
+			MX6UL_PAD_UART5_RX_DATA__I2C2_SDA		0x4001f8a8
+		>;
+	};
+
+	mux_uart: uartgrp {
+		fsl,pins = <
+			MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX		0x1b0b1
+			MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX		0x1b0b1
+		>;
+	};
+
+	mux_gpio_keys: gpiokeygrp {
+		fsl,pins = <
+			MX6UL_PAD_ENET2_TX_DATA0__GPIO2_IO11		0x3008
+			MX6UL_PAD_ENET2_TX_DATA1__GPIO2_IO12		0x3008
+			MX6UL_PAD_ENET2_TX_EN__GPIO2_IO13		0x3008
+			MX6UL_PAD_ENET2_RX_EN__GPIO2_IO10		0x3008
+			MX6UL_PAD_ENET2_RX_DATA1__GPIO2_IO09		0x3008
+			MX6UL_PAD_ENET2_RX_ER__GPIO2_IO15		0x3008
+			MX6UL_PAD_ENET2_RX_DATA0__GPIO2_IO08		0x3008
+			MX6UL_PAD_ENET2_TX_CLK__GPIO2_IO14		0x3008
+			MX6UL_PAD_ENET1_TX_DATA0__GPIO2_IO03		0x3008
+			MX6UL_PAD_ENET1_RX_DATA1__GPIO2_IO01		0x3008
+		>;
+	};
+
+	mux_led_ctrl: ledctrlgrp {
+		fsl,pins = <
+			MX6UL_PAD_ENET1_RX_EN__GPIO2_IO02		0x3008
+		>;
+	};
+
+	mux_adc: adcgrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO07__GPIO1_IO07		0xb0
+		>;
+	};
+
+	mux_pwm: pwm1grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO08__PWM1_OUT			0x110b0
+		>;
+	};
+
+	mux_backlight_enable: blenablegrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO09__GPIO1_IO09		0x3008
+		>;
+	};
+
+	mux_lcd_data: lcdifdatgrp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA00__LCDIF_DATA00		0x79
+			MX6UL_PAD_LCD_DATA01__LCDIF_DATA01		0x79
+			MX6UL_PAD_LCD_DATA02__LCDIF_DATA02		0x79
+			MX6UL_PAD_LCD_DATA03__LCDIF_DATA03		0x79
+			MX6UL_PAD_LCD_DATA04__LCDIF_DATA04		0x79
+			MX6UL_PAD_LCD_DATA05__LCDIF_DATA05		0x79
+			MX6UL_PAD_LCD_DATA06__LCDIF_DATA06		0x79
+			MX6UL_PAD_LCD_DATA07__LCDIF_DATA07		0x79
+			MX6UL_PAD_LCD_DATA08__LCDIF_DATA08		0x79
+			MX6UL_PAD_LCD_DATA09__LCDIF_DATA09		0x79
+			MX6UL_PAD_LCD_DATA10__LCDIF_DATA10		0x79
+			MX6UL_PAD_LCD_DATA11__LCDIF_DATA11		0x79
+			MX6UL_PAD_LCD_DATA12__LCDIF_DATA12		0x79
+			MX6UL_PAD_LCD_DATA13__LCDIF_DATA13		0x79
+			MX6UL_PAD_LCD_DATA14__LCDIF_DATA14		0x79
+			MX6UL_PAD_LCD_DATA15__LCDIF_DATA15		0x79
+			MX6UL_PAD_LCD_DATA16__LCDIF_DATA16		0x79
+			MX6UL_PAD_LCD_DATA17__LCDIF_DATA17		0x79
+		>;
+	};
+
+	mux_lcd_ctrl: lcdifctrlgrp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_CLK__LCDIF_CLK			0x79
+			MX6UL_PAD_LCD_ENABLE__LCDIF_ENABLE		0x79
+			MX6UL_PAD_LCD_HSYNC__LCDIF_HSYNC		0x79
+			MX6UL_PAD_LCD_VSYNC__LCDIF_VSYNC		0x79
+		>;
+	};
+
+	mux_csi: csi1grp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_PIXCLK__CSI_PIXCLK		0x1b088
+			MX6UL_PAD_CSI_VSYNC__CSI_VSYNC			0x1b088
+			MX6UL_PAD_CSI_HSYNC__CSI_HSYNC			0x1b088
+			MX6UL_PAD_CSI_DATA00__CSI_DATA02		0x1b088
+			MX6UL_PAD_CSI_DATA01__CSI_DATA03		0x1b088
+			MX6UL_PAD_CSI_DATA02__CSI_DATA04		0x1b088
+			MX6UL_PAD_CSI_DATA03__CSI_DATA05		0x1b088
+			MX6UL_PAD_CSI_DATA04__CSI_DATA06		0x1b088
+			MX6UL_PAD_CSI_DATA05__CSI_DATA07		0x1b088
+			MX6UL_PAD_CSI_DATA06__CSI_DATA08		0x1b088
+			MX6UL_PAD_CSI_DATA07__CSI_DATA09		0x1b088
+		>;
+	};
+
+	mux_gc0308: gc0308grp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_MCLK__CSI_MCLK			0x1e038
+			MX6UL_PAD_GPIO1_IO05__GPIO1_IO05		0x1b088
+			MX6UL_PAD_GPIO1_IO06__GPIO1_IO06		0x1b088
+		>;
+	};
+
+
+	mux_spi3: ecspi3grp {
+		fsl,pins = <
+			MX6UL_PAD_UART2_CTS_B__ECSPI3_MOSI		0x100b1
+			MX6UL_PAD_UART2_RX_DATA__ECSPI3_SCLK		0x100b1
+			MX6UL_PAD_UART2_TX_DATA__GPIO1_IO20		0x3008
+		>;
+	};
+};
-- 
2.43.0

Re: [PATCH v4 06/16] dt-bindings: lcdif: Do not require power-domains for i.MX6ULL

[Fabio Estevam]

On Sat, Feb 24, 2024 at 6:33 PM Sebastian Reichel <sre@kernel.org> wrote:
>
> i.MX6UL(L) uses "fsl,imx6sx-lcdif" as fallback compatible string,
> but has only very lightweight DISPLAY power domain. Its DISPLAY
> power domain is not supported by the binding / Linux kernel at
> the moment. Since the current setup is working, let's remove the
> power-domain from being required for that platform to fix the warning
> printed by CHECK_DTBS=y.

Thanks, this also fixes the following imx8mq warnings:

imx8mq-evk.dtb: lcd-controller@30320000: 'power-domains' is a required property
from schema $id: http://devicetree.org/schemas/display/fsl,lcdif.yaml#

Reviewed-by: Fabio Estevam <festevam@gmail.com>

Re: [PATCH v4 16/16] ARM: dts: imx6ull-uti260b: Add board

[Fabio Estevam]

On Sat, Feb 24, 2024 at 6:33 PM Sebastian Reichel <sre@kernel.org> wrote:

> +&gpio2 {
> +       /* configuring this to output-high results in poweroff */
> +       power-en-hog {
> +               gpio-hog;
> +               gpios = <6 GPIO_ACTIVE_HIGH>;
> +               line-name = "power-en-gpio";
> +               output-low;
> +               pinctrl-names = "default";
> +               pinctrl-0 = <&mux_poweroff2>;
> +       };
> +};
> +
> +&ecspi3 {

It is recommended to put the nodes in alphabetical order (except
iomuxc, which is the last one).

> +       mux_gc0308: gc0308grp {
> +               fsl,pins = <
> +                       MX6UL_PAD_CSI_MCLK__CSI_MCLK                    0x1e038
> +                       MX6UL_PAD_GPIO1_IO05__GPIO1_IO05                0x1b088
> +                       MX6UL_PAD_GPIO1_IO06__GPIO1_IO06                0x1b088
> +               >;
> +       };
> +
> +

There is an extra blank line here.

Reviewed-by: Fabio Estevam <festevam@gmail.com>

Re: [PATCH v4 10/16] ARM: dts: imx6ul: add missing #thermal-sensor-cells

[Shawn Guo]

On Sat, Feb 24, 2024 at 10:29:42PM +0100, Sebastian Reichel wrote:
> Fix the following warning found via CHECK_DTBS:
> 
> tempmon: '#thermal-sensor-cells' is a required property
> 
> Signed-off-by: Sebastian Reichel <sre@kernel.org>

Thanks for the patch!  But I had picked up the one [1] from Alexander
Stein.

Shawn

[1] https://lore.kernel.org/linux-arm-kernel/ZcCNdrQPb10i4rl2@t480/T/

Re: [PATCH v4 08/16] ARM: dts: imx6ull: fix pinctrl node name

[Shawn Guo]

On Sat, Feb 24, 2024 at 10:29:40PM +0100, Sebastian Reichel wrote:
> pinctrl node name must be either pinctrl or pinmux.
> 
> Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> Signed-off-by: Sebastian Reichel <sre@kernel.org>

Applied, thanks!

Re: [PATCH v4 09/16] ARM: dts: imx6ul: Remove fsl,anatop from usbotg1

[Shawn Guo]

On Sat, Feb 24, 2024 at 10:29:41PM +0100, Sebastian Reichel wrote:
> fsl,anatop should only be added to the usbphy nodes.
> 
> Signed-off-by: Sebastian Reichel <sre@kernel.org>

Applied, thanks!

Re: [PATCH v4 11/16] ARM: dts: nxp: imx6ul: xnur-gpio -> xnur-gpios

[Shawn Guo]

On Sat, Feb 24, 2024 at 10:29:43PM +0100, Sebastian Reichel wrote:
> Replace all "xnur-gpio" with "xnur-gpios" in the i.MX6UL(L) Touchscreen
> node, since the -gpio suffix is deprecated. All known implementations of
> this binding can handle -gpio and -gpios since day 1, so this should be
> fully backwards compatible.
> 
> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> Signed-off-by: Sebastian Reichel <sre@kernel.org>

Applied, thanks!

Re: [PATCH v4 12/16] ARM: dts: nxp: imx6ul: fix touchscreen node name

[Shawn Guo]

On Sat, Feb 24, 2024 at 10:29:44PM +0100, Sebastian Reichel wrote:
> The canonical node name for touchscreens is "touchscreen",
> so update the i.MX6UL "tsc" node accordingly.
> 
> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> Signed-off-by: Sebastian Reichel <sre@kernel.org>

Applied, thanks!

Re: [PATCH v4 13/16] ARM: dts: nxp: imx: fix weim node name

[Shawn Guo]

On Sat, Feb 24, 2024 at 10:29:45PM +0100, Sebastian Reichel wrote:
> DT node names should be generic, so replace "weim" node name with
> "memory-controller" in all i.MX SoC DT files.
> 
> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> Signed-off-by: Sebastian Reichel <sre@kernel.org>

Applied, thanks!

Re: [PATCH v4 14/16] dt-bindings: vendor-prefixes: add UNI-T

[Shawn Guo]

On Sat, Feb 24, 2024 at 10:29:46PM +0100, Sebastian Reichel wrote:
> Uni-Trend Technology is a manufacturer of measurement
> and testing tools.
> 
> Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> Signed-off-by: Sebastian Reichel <sre@kernel.org>

Applied, thanks!

Re: [PATCH v4 15/16] dt-bindings: arm: add UNI-T UTi260B

[Shawn Guo]

On Sat, Feb 24, 2024 at 10:29:47PM +0100, Sebastian Reichel wrote:
> Add compatible value for i.MX6ULL based UNI-T UTi260B thermal camera.
> 
> Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> Signed-off-by: Sebastian Reichel <sre@kernel.org>

Applied, thanks!

Re: [PATCH v4 16/16] ARM: dts: imx6ull-uti260b: Add board

[Shawn Guo]

On Sat, Feb 24, 2024 at 10:29:48PM +0100, Sebastian Reichel wrote:
> Add UNI-T UTi260b thermal camera board.
> 
> Reviewed-by: Stefan Wahren <wahrenst@gmx.net>
> Signed-off-by: Sebastian Reichel <sre@kernel.org>

Can we change the patch subject to something like below?

  ARM: dts: imx: Add UNI-T UTi260b thermal camera board

Shawn

Re: (subset) [PATCH v4 02/16] dt-bindings: bus: imx-weim: convert to YAML

[Krzysztof Kozlowski]

On Sat, 24 Feb 2024 22:29:34 +0100, Sebastian Reichel wrote:
> Convert the i.MX  Wireless External Interface Module binding to YAML.
> 
> 

Applied, thanks!

[02/16] dt-bindings: bus: imx-weim: convert to YAML
        https://git.kernel.org/krzk/linux-mem-ctrl/c/3884bdce169de87d3f978edf41829e5e52388072

Best regards,
-- 
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Re: [PATCH v4 06/16] dt-bindings: lcdif: Do not require power-domains for i.MX6ULL

[Rob Herring]

On Sat, 24 Feb 2024 22:29:38 +0100, Sebastian Reichel wrote:
> i.MX6UL(L) uses "fsl,imx6sx-lcdif" as fallback compatible string,
> but has only very lightweight DISPLAY power domain. Its DISPLAY
> power domain is not supported by the binding / Linux kernel at
> the moment. Since the current setup is working, let's remove the
> power-domain from being required for that platform to fix the warning
> printed by CHECK_DTBS=y.
> 
> Fixes: f62678a77d58 ("dt-bindings: mxsfb: Document i.MX8M/i.MX6SX/i.MX6SL power-domains property")
> Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> Signed-off-by: Sebastian Reichel <sre@kernel.org>
> ---
>  Documentation/devicetree/bindings/display/fsl,lcdif.yaml | 8 +++++++-
>  1 file changed, 7 insertions(+), 1 deletion(-)
> 

Applied, thanks!