USB 2.0 ehci failure with large amount of RAM (4GB) on x86_64

USB 2.0 ehci failure with large amount of RAM (4GB) on x86_64

[Nathan Becker]

Hi,

I recently added two more memory modules to my Gigabyte K8NXP-SLI
motherboard, bringing the total up to 4GB.  I had 2GB previously and
things were running well with kernel 2.6.16.9 x86_64. The CPU is an
AMD 4800+ X2.

After the upgrade, USB 2.0 stopped working. After connecting a pen
drive the following dmesg comes up

ehci_hcd 0000:00:02.1: GetStatus port 3 status 001803 POWER sig=j CSC CONNECT
hub 1-0:1.0: port 3, status 0501, change 0001, 480 Mb/s
hub 1-0:1.0: debounce: port 3: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:02.1: port 3 high speed
ehci_hcd 0000:00:02.1: GetStatus port 3 status 001005 POWER sig=se0 PE CONNECT
usb 1-3: new high speed USB device using ehci_hcd and address 4
usb 1-3: khubd timed out on ep0in len=0/64
usb 1-3: khubd timed out on ep0in len=0/64
usb 1-3: khubd timed out on ep0in len=0/64

and then it repeats attempting different addresses.  If I rmmod
ehci_hcd, then I can get the device to work, of course it's just
running at USB  1.1.

There appear to be varying reports of this problem in bugzilla and on
message boards:
bugzilla #5835
bugzilla #6201

 I am not sure which of these, if any, are the same as the problem I'm
having.  Any advice on where to go with this problem would be much
appreciated.  I suspect that a significant clue to this is that it
only occurs with large amounts of RAM. It also only seems to occur in
64-bit mode.  I booted a 32-bit kernel from the Slax live CD  5.1.0
and USB 2.0 worked fine with all my RAM intact (well only 3.4 GB, but
that's a different story). I'm happy to post more details and or try
patches out.  I just retested with kernel  2.6.16.13 and the problem
persists.

I've already tried various combinations of  settings in the BIOS, but
they have no effect.  There is an option to remap for 4GB.  If that is
turned off then the kernel only sees  3.4 GB of RAM instead of 4GB,
but it seems to have no effect on this problem.  I also tried changing
the USB memory option between shadow and lowmem.  That also had no
effect on this problem.  I do use the NVIDIA binary graphics driver,
but I retested for this problem without it loaded and the problem
persists.

Please cc me directly with any replies. Thanks very much for your help,


Nathan

Re: USB 2.0 ehci failure with large amount of RAM (4GB) on x86_64

[Greg KH]

On Wed, May 03, 2006 at 09:52:11PM -0700, Nathan Becker wrote:
> Hi,
> 
> I recently added two more memory modules to my Gigabyte K8NXP-SLI
> motherboard, bringing the total up to 4GB.  I had 2GB previously and
> things were running well with kernel 2.6.16.9 x86_64. The CPU is an
> AMD 4800+ X2.
> 
> After the upgrade, USB 2.0 stopped working. After connecting a pen
> drive the following dmesg comes up
> 
> ehci_hcd 0000:00:02.1: GetStatus port 3 status 001803 POWER sig=j CSC 
> CONNECT
> hub 1-0:1.0: port 3, status 0501, change 0001, 480 Mb/s
> hub 1-0:1.0: debounce: port 3: total 100ms stable 100ms status 0x501
> ehci_hcd 0000:00:02.1: port 3 high speed
> ehci_hcd 0000:00:02.1: GetStatus port 3 status 001005 POWER sig=se0 PE 
> CONNECT
> usb 1-3: new high speed USB device using ehci_hcd and address 4
> usb 1-3: khubd timed out on ep0in len=0/64
> usb 1-3: khubd timed out on ep0in len=0/64
> usb 1-3: khubd timed out on ep0in len=0/64
> 
> and then it repeats attempting different addresses.  If I rmmod
> ehci_hcd, then I can get the device to work, of course it's just
> running at USB  1.1.
> 
> There appear to be varying reports of this problem in bugzilla and on
> message boards:
> bugzilla #5835
> bugzilla #6201
> 
> I am not sure which of these, if any, are the same as the problem I'm
> having.  Any advice on where to go with this problem would be much
> appreciated.  I suspect that a significant clue to this is that it
> only occurs with large amounts of RAM. It also only seems to occur in
> 64-bit mode.  I booted a 32-bit kernel from the Slax live CD  5.1.0
> and USB 2.0 worked fine with all my RAM intact (well only 3.4 GB, but
> that's a different story). I'm happy to post more details and or try
> patches out.  I just retested with kernel  2.6.16.13 and the problem
> persists.
> 
> I've already tried various combinations of  settings in the BIOS, but
> they have no effect.  There is an option to remap for 4GB.  If that is
> turned off then the kernel only sees  3.4 GB of RAM instead of 4GB,
> but it seems to have no effect on this problem.  I also tried changing
> the USB memory option between shadow and lowmem.  That also had no
> effect on this problem.  I do use the NVIDIA binary graphics driver,
> but I retested for this problem without it loaded and the problem
> persists.

Can you try 2.6.17-rc3?

Also, when booting, are there any messages about EHCI BIOS handoffs?
I've seen some reports of this in the past, but it seems to be fixed
with updated bioses.

Andi, you remember what fixed this the last time?

David, any thoughts?

thanks,

greg k-h

Re: USB 2.0 ehci failure with large amount of RAM (4GB) on x86_64

[Andi Kleen]

On Thursday 04 May 2006 07:27, Greg KH wrote:

> Andi, you remember what fixed this the last time?

IIRC there wasn't a fix - just a conclusion that in one case it was likely
a bad interaction with SMM code. In the other case we didn't get that far.

-Andi

Re: USB 2.0 ehci failure with large amount of RAM (4GB) on x86_64

[Nathan Becker]

I tried 2.6.17-rc3 and the problem persists.  I don't see any messages
about EHCI BIOS handoffs.

Re: USB 2.0 ehci failure with large amount of RAM (4GB) on x86_64

[David Brownell]

> On Wed, May 03, 2006 at 09:52:11PM -0700, Nathan Becker wrote:
> > Hi,
> > 
> > I recently added two more memory modules to my Gigabyte K8NXP-SLI
> > motherboard, bringing the total up to 4GB.  I had 2GB previously and
> > things were running well with kernel 2.6.16.9 x86_64. The CPU is an
> > AMD 4800+ X2.
> > 
> > After the upgrade, USB 2.0 stopped working...

There's an erratum in NF4 parts affecting certain EHCI accesses to
memory addresses over the 2GB mark, and you might be seeing this.

Presumably you're running with the GART IOMMU?  If not, then turn
that on.  Maybe even turn on IOMMU_DEBUG.

Another experiment might be taking the PCI_VENDOR_ID_NVIDIA case
in drivers/usb/host/ehci-pci.c and adding a call to dma_set_mask()
in addition to the existing call.

- Dave

Re: USB 2.0 ehci failure with large amount of RAM (4GB) on x86_64

[Nathan Becker]

Yes, GART_IOMMU is already turned on.  Do you want me to send more
detailed debugging messages?

> Presumably you're running with the GART IOMMU?  If not, then turn
> that on.  Maybe even turn on IOMMU_DEBUG.

Re: USB 2.0 ehci failure with large amount of RAM (4GB) on x86_64

[David Brownell]

On Thursday 04 May 2006 10:46 pm, Nathan Becker wrote:
> Yes, GART_IOMMU is already turned on.  Do you want me to send more
> detailed debugging messages?

And when you tell the kernel to only use 2 GB, it works again right?
Just trying to rule out hardware or hardware-init bugs.

Maybe you could change both dma masks to be 31 bits and then force the
IOMMU active, so it gives out addresses below 2GB.  You should be able
to make it so that the EHCI controller never sees addresss with the
high bit set, making your 4 GB config act like a 2 GB one (via IOMMU).

Which one hopes means "working" ... it'd be good to know a workaround!

This isn't neceessarily a variant of that known NForce silicon bug, but you
could help confirm that by changing the "3strikes" message so it prints
out urb->transfer_dma ... and maybe make qh_completions() dump the dma
addresses of the qh and qtd too (iff urb->status becomes -EPROTO).

Re: USB 2.0 ehci failure with large amount of RAM (4GB) on x86_64

[Nathan Becker]

Thanks for all suggestions.  I tried passing mem=2048m to the kernel. 
This is with 2.6.16.13.  This did fix the USB ehci problem.  Of course
the kernel only sees half of my RAM, so this is not a satisfactory
long-term workaround.

As for your other suggestions, I'm not sure how to implement those. 
I'm not a kernel developer.  If you can give me more specific
instructions or send me a patch I would be happy to try those out. 
Otherwise, if you feel that this is unrelated to the other entries in
bugzilla with similar symptoms, I would be happy to submit a bug
report.

Re: USB 2.0 ehci failure with large amount of RAM (4GB) on x86_64

[Nathan Becker]

Like I said in my previous message, I am not a kernel developer.  I am
a programmer though, so I thought I'd give your suggestions a try.

I added 1 line to drivers/usb/host/ehci-pci.c which sets the DMA mask,
and now it seems to work with ehci loaded and with 4 GB of RAM.
Unfortunately, I don't really understand what I did.  Perhaps you have
a better idea what this is doing and if it is correct.

case PCI_VENDOR_ID_NVIDIA:
		/* NVidia reports that certain chips don't handle
		 * QH, ITD, or SITD addresses above 2GB.  (But TD,
		 * data buffer, and periodic schedule are normal.)
		 */
		
		dma_set_mask(hcd->self.controller, DMA_31BIT_MASK); /* I added this line */
		
		switch (pdev->device) {
		case 0x003c:	/* MCP04 */
		case 0x005b:	/* CK804 */
		case 0x00d8:	/* CK8 */
		case 0x00e8:	/* CK8S */
			if (pci_set_consistent_dma_mask(pdev,
						DMA_31BIT_MASK) < 0)
				ehci_warn(ehci, "can't enable NVidia "
					"workaround for >2GB RAM\n");
			break;
		}
		break;
	}

Re: USB 2.0 ehci failure with large amount of RAM (4GB) on x86_64

[Nathan Becker]

In my last message I sent a patch that I thought fixed the problem.

I made a mistake in my testing.  It turns out that my patch doesn't
have an effect on this problem.  What I discovered was a workaround: 
If I rmmod ehci-hcd and then modprobe it back in, usb 2.0 it works. 
That's what I did when I tested my patched version, so I mistakenly
thought it was my patch that fixed it.

So it seems that there is something that happens when the ehci-hcd
shuts down that helps initialize it to work properly.  What could it
be?

Re: [linux-usb-devel] Re: USB 2.0 ehci failure with large amount of RAM (4GB) on x86_64

[David Brownell]

[-- Attachment #1: Type: text/plain, Size: 702 bytes --]

On Tuesday 09 May 2006 10:37 pm, Nathan Becker wrote:
> I added 1 line to drivers/usb/host/ehci-pci.c which sets the DMA mask,
> and now it seems to work with ehci loaded and with 4 GB of RAM.
> Unfortunately, I don't really understand what I did.  Perhaps you have
> a better idea what this is doing and if it is correct.

Interesting.  My guess is that the IOMMU is helping you out, and the
issue is that the silicon erratum applies to the I/O buffers too, not
just to a subset of the schedule data structures.

Can you confirm that this patch also resolves your issue?  Reboot
from scratch a few times (power off, warm reboot, etc) to be
reasonably sure you're seeing the cases that failed before.


[-- Attachment #2: ehci-nf4.patch --]
[-- Type: text/x-diff, Size: 1197 bytes --]

Modify workaround for the EHCI quirk in newer NVidia controllers by
assigning the DMA mask, not just the consistent DMA mask.  It seems
to matter, as if the silicon erratum isn't quite what was described
in the original bug workaround (or there's another erratum).


Index: g26/drivers/usb/host/ehci-pci.c
===================================================================
--- g26.orig/drivers/usb/host/ehci-pci.c	2006-05-12 19:40:22.000000000 -0700
+++ g26/drivers/usb/host/ehci-pci.c	2006-05-12 21:15:31.000000000 -0700
@@ -118,7 +118,15 @@ static int ehci_pci_setup(struct usb_hcd
 			if (pci_set_consistent_dma_mask(pdev,
 						DMA_31BIT_MASK) < 0)
 				ehci_warn(ehci, "can't enable NVidia "
-					"workaround for >2GB RAM\n");
+					"workaround %d for >2GB RAM\n", 1);
+
+			/* some users report problems with 4GB when the IOMMU
+			 * doesn't force lowmem addresses... looks like the
+			 * initial report from NVidia wasn't quite right.
+			 */
+			if (pci_set_dma_mask(pdev, DMA_31BIT_MASK) < 0)
+				ehci_warn(ehci, "can't enable NVidia "
+					"workaround %d for >2GB RAM\n", 2);
 			break;
 		/* Some NForce2 chips have problems with selective suspend;
 		 * fixed in newer silicon.

Re: [linux-usb-devel] Re: USB 2.0 ehci failure with large amount of RAM (4GB) on x86_64

[Nathan Becker]

Thanks for the patch.  However, did you not get my very last message?
Checking back through my mail logs, I think it might not have been
delivered.

After claiming that the dma mask fixed the problem, I quickly
discovered that the dma was not what did it.  Thus the patch you sent
does not work.

But, here is what does: If I rmmod ehci_hcd and then modprobe
ehci_hcd, it works, and I get full USB 2.0 speed.  There must be
something happening in the clean-up code of the the ehci_hcd  that
fixes whatever conflict I'm having.  When I originally made that patch
and then reloaded the ehci_hcd module to test it, I mistakenly thought
that it was the patch that was fixing the problem.  I should have
tested more thoroughly before sending the e-mail, but I got very
excited.  Sorry about that.  After several days of using the
rmmod/modprobe workaround, I do feel confident that it is a legitimate
fix.

Re: [linux-usb-devel] Re: USB 2.0 ehci failure with large amount of RAM (4GB) on x86_64

[Pete Zaitcev]

On Fri, 12 May 2006 21:32:39 -0700, David Brownell <david-b@pacbell.net> wrote:

> Can you confirm that this patch also resolves your issue? [...]

I noticed that you added the mask inside the case while Nathan
added it outside. So, he did it for all nVidia silicon.

I would think it may be better if he tested your patch very
exactly on top of a clean kernel (e.g. make sure that his own
patch is not in the way), and also sent us the lspci output
with the chip revision numbers.

-- Pete

Re: [linux-usb-devel] Re: USB 2.0 ehci failure with large amount of RAM (4GB) on x86_64

[Will Dyson]

[-- Attachment #1: Type: text/plain, Size: 2121 bytes --]

On 5/16/06, Pete Zaitcev <zaitcev@redhat.com> wrote:
> On Fri, 12 May 2006 21:32:39 -0700, David Brownell <david-b@pacbell.net> wrote:
>
> > Can you confirm that this patch also resolves your issue? [...]
>
> I noticed that you added the mask inside the case while Nathan
> added it outside. So, he did it for all nVidia silicon.
>
> I would think it may be better if he tested your patch very
> exactly on top of a clean kernel (e.g. make sure that his own
> patch is not in the way), and also sent us the lspci output
> with the chip revision numbers.

I'm having a similar-seeming issue on my nforce3 board w/ 3GB ram. I
can use my usb2 devices normally if I boot with mem=2G but if I allow
linux to see all 3GB, plugging in a usb2 hub goes like this (full
dmesg and lspci attatched):

hub 3-0:1.0: state 7 ports 8 chg 0000 evt 0010
ehci_hcd 0000:00:02.2: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 3-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 3-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:02.2: port 4 high speed
ehci_hcd 0000:00:02.2: GetStatus port 4 status 001005 POWER sig=se0 PE CONNECT
usb 3-4: new high speed USB device using ehci_hcd and address 4
usb 3-4: khubd timed out on ep0in len=0/64
usb 3-4: khubd timed out on ep0in len=0/64
usb 3-4: khubd timed out on ep0in len=0/64
ehci_hcd 0000:00:02.2: port 4 high speed
ehci_hcd 0000:00:02.2: GetStatus port 4 status 001005 POWER sig=se0 PE CONNECT
usb 3-4: device descriptor read/64, error -110
usb 3-4: khubd timed out on ep0in len=0/64
usb 3-4: khubd timed out on ep0in len=0/64
usb 3-4: khubd timed out on ep0in len=0/64
ehci_hcd 0000:00:02.2: port 4 high speed
ehci_hcd 0000:00:02.2: GetStatus port 4 status 001005 POWER sig=se0 PE CONNECT
usb 3-4: device descriptor read/64, error -110
ehci_hcd 0000:00:02.2: port 4 high speed
ehci_hcd 0000:00:02.2: GetStatus port 4 status 001005 POWER sig=se0 PE CONNECT
usb 3-4: new high speed USB device using ehci_hcd and address 5

I tested the above patch and it does not resolve the issue.

-- 
Will Dyson

[-- Attachment #2: lspci.txt --]
[-- Type: text/plain, Size: 15584 bytes --]

0000:00:00.0 Host bridge: nVidia Corporation nForce3 250Gb Host Bridge (rev a1)
	Subsystem: Micro-Star International Co., Ltd.: Unknown device 0250
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0
	Region 0: Memory at e8000000 (32-bit, prefetchable) [size=128M]
	Capabilities: [44] #08 [01c0]
	Capabilities: [c0] AGP version 3.0
		Status: RQ=32 Iso- ArqSz=2 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3+ Rate=x4,x8
		Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x4

0000:00:01.0 ISA bridge: nVidia Corporation nForce3 250Gb LPC Bridge (rev a2)
	Subsystem: Micro-Star International Co., Ltd.: Unknown device 0250
	Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0

0000:00:01.1 SMBus: nVidia Corporation nForce 250Gb PCI System Management (rev a1)
	Subsystem: Micro-Star International Co., Ltd.: Unknown device 0250
	Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Interrupt: pin A routed to IRQ 3
	Region 0: I/O ports at e800 [size=32]
	Region 4: I/O ports at 4c00 [size=64]
	Region 5: I/O ports at 4c40 [size=64]
	Capabilities: [44] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:02.0 USB Controller: nVidia Corporation CK8S USB Controller (rev a1) (prog-if 10 [OHCI])
	Subsystem: Micro-Star International Co., Ltd.: Unknown device 0250
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0 (750ns min, 250ns max)
	Interrupt: pin A routed to IRQ 217
	Region 0: Memory at f6003000 (32-bit, non-prefetchable) [size=4K]
	Capabilities: [44] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:02.1 USB Controller: nVidia Corporation CK8S USB Controller (rev a1) (prog-if 10 [OHCI])
	Subsystem: Micro-Star International Co., Ltd.: Unknown device 0250
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0 (750ns min, 250ns max)
	Interrupt: pin B routed to IRQ 185
	Region 0: Memory at f6004000 (32-bit, non-prefetchable) [size=4K]
	Capabilities: [44] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:02.2 USB Controller: nVidia Corporation nForce3 EHCI USB 2.0 Controller (rev a2) (prog-if 20 [EHCI])
	Subsystem: Micro-Star International Co., Ltd.: Unknown device 0250
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0 (750ns min, 250ns max)
	Interrupt: pin C routed to IRQ 201
	Region 0: Memory at f6005000 (32-bit, non-prefetchable) [size=256]
	Capabilities: [44] #0a [2098]
	Capabilities: [80] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:05.0 Bridge: nVidia Corporation CK8S Ethernet Controller (rev a2)
	Subsystem: Micro-Star International Co., Ltd.: Unknown device 0250
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0 (250ns min, 5000ns max)
	Interrupt: pin A routed to IRQ 185
	Region 0: Memory at f6000000 (32-bit, non-prefetchable) [size=4K]
	Region 1: I/O ports at a400 [size=8]
	Capabilities: [44] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
		Status: D0 PME-Enable+ DSel=0 DScale=0 PME-

0000:00:06.0 Multimedia audio controller: nVidia Corporation nForce3 250Gb AC'97 Audio Controller (rev a1)
	Subsystem: Micro-Star International Co., Ltd.: Unknown device 7585
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0 (500ns min, 1250ns max)
	Interrupt: pin A routed to IRQ 193
	Region 0: I/O ports at a800 [size=256]
	Region 1: I/O ports at ac00 [size=128]
	Region 2: Memory at f6001000 (32-bit, non-prefetchable) [size=4K]
	Capabilities: [44] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:08.0 IDE interface: nVidia Corporation CK8S Parallel ATA Controller (v2.5) (rev a2) (prog-if 8a [Master SecP PriP])
	Subsystem: Micro-Star International Co., Ltd.: Unknown device 0250
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0 (750ns min, 250ns max)
	Region 4: I/O ports at f000 [size=16]
	Capabilities: [44] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:09.0 IDE interface: nVidia Corporation CK8S Serial ATA Controller (v2.5) (rev a2) (prog-if 85 [Master SecO PriO])
	Subsystem: Micro-Star International Co., Ltd.: Unknown device 0250
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0 (750ns min, 250ns max)
	Interrupt: pin A routed to IRQ 193
	Region 0: I/O ports at 09e0 [size=8]
	Region 1: I/O ports at 0be0 [size=4]
	Region 2: I/O ports at 0960 [size=8]
	Region 3: I/O ports at 0b60 [size=4]
	Region 4: I/O ports at c800 [size=16]
	Region 5: I/O ports at cc00 [size=128]
	Capabilities: [44] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:0a.0 IDE interface: nVidia Corporation CK8S Serial ATA Controller (v2.5) (rev a2) (prog-if 85 [Master SecO PriO])
	Subsystem: Micro-Star International Co., Ltd.: Unknown device 0250
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0 (750ns min, 250ns max)
	Interrupt: pin A routed to IRQ 201
	Region 0: I/O ports at 09f0 [size=8]
	Region 1: I/O ports at 0bf0 [size=4]
	Region 2: I/O ports at 0970 [size=8]
	Region 3: I/O ports at 0b70 [size=4]
	Region 4: I/O ports at e000 [size=16]
	Region 5: I/O ports at e400 [size=128]
	Capabilities: [44] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:00:0b.0 PCI bridge: nVidia Corporation nForce3 250Gb AGP Host to PCI Bridge (rev a2) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
	Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 16
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=10
	I/O behind bridge: 00008000-00008fff
	Memory behind bridge: f4000000-f5ffffff
	Prefetchable memory behind bridge: d8000000-e7ffffff
	BridgeCtl: Parity- SERR+ NoISA+ VGA+ MAbort- >Reset- FastB2B-

0000:00:0e.0 PCI bridge: nVidia Corporation nForce3 250Gb PCI-to-PCI Bridge (rev a2) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
	Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0
	Bus: primary=00, secondary=02, subordinate=02, sec-latency=128
	I/O behind bridge: 00009000-00009fff
	Memory behind bridge: f0000000-f3ffffff
	Prefetchable memory behind bridge: c4000000-c40fffff
	BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-

0000:00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Capabilities: [80] #08 [2101]

0000:00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-

0000:00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-

0000:00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-

0000:01:00.0 VGA compatible controller: ATI Technologies Inc RV280 [Radeon 9200] (rev 01) (prog-if 00 [VGA])
	Subsystem: C.P. Technology Co. Ltd: Unknown device 2063
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32 (2000ns min), Cache Line Size: 0x08 (32 bytes)
	Interrupt: pin A routed to IRQ 177
	Region 0: Memory at d8000000 (32-bit, prefetchable) [size=128M]
	Region 1: I/O ports at 8000 [size=256]
	Region 2: Memory at f5010000 (32-bit, non-prefetchable) [size=64K]
	Expansion ROM at f4000000 [disabled] [size=128K]
	Capabilities: [58] AGP version 3.0
		Status: RQ=256 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3+ Rate=x4,x8
		Command: RQ=32 ArqSz=2 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x4
	Capabilities: [50] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:01:00.1 Display controller: ATI Technologies Inc RV280 [Radeon 9200] (Secondary) (rev 01)
	Subsystem: C.P. Technology Co. Ltd: Unknown device 2062
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Region 0: Memory at e0000000 (32-bit, prefetchable) [disabled] [size=128M]
	Region 1: Memory at f5000000 (32-bit, non-prefetchable) [disabled] [size=64K]
	Capabilities: [50] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:02:08.0 Multimedia video controller: Conexant CX23880/1/2/3 PCI Video and Audio Decoder (rev 05)
	Subsystem: pcHDTV pcHDTV HD3000 HDTV
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32 (5000ns min, 13750ns max), Cache Line Size: 0x08 (32 bytes)
	Interrupt: pin A routed to IRQ 233
	Region 0: Memory at f0000000 (32-bit, non-prefetchable) [size=16M]
	Capabilities: [44] Vital Product Data
	Capabilities: [4c] Power Management version 2
		Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:02:08.2 Multimedia controller: Conexant CX23880/1/2/3 PCI Video and Audio Decoder [MPEG Port] (rev 05)
	Subsystem: pcHDTV pcHDTV HD3000 HDTV
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32 (1500ns min, 22000ns max), Cache Line Size: 0x08 (32 bytes)
	Interrupt: pin A routed to IRQ 233
	Region 0: Memory at f1000000 (32-bit, non-prefetchable) [size=16M]
	Capabilities: [4c] Power Management version 2
		Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:02:0a.0 Multimedia audio controller: Creative Labs SB Live! EMU10k1 (rev 05)
	Subsystem: Creative Labs CT4850 SBLive! Value
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32 (500ns min, 5000ns max)
	Interrupt: pin A routed to IRQ 225
	Region 0: I/O ports at 9000 [size=32]
	Capabilities: [dc] Power Management version 1
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:02:0a.1 Input device controller: Creative Labs SB Live! MIDI/Game Port (rev 05)
	Subsystem: Creative Labs Gameport Joystick
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32
	Region 0: I/O ports at 9400 [size=8]
	Capabilities: [dc] Power Management version 1
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:02:0c.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host Controller (rev 46) (prog-if 10 [OHCI])
	Subsystem: Unknown device 0574:086c
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32, Cache Line Size: 0x08 (32 bytes)
	Interrupt: pin A routed to IRQ 209
	Region 0: Memory at f3001000 (32-bit, non-prefetchable) [size=2K]
	Region 1: I/O ports at 9800 [size=128]
	Capabilities: [50] Power Management version 2
		Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA PME(D0-,D1-,D2+,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

0000:02:0d.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8169 Gigabit Ethernet (rev 10)
	Subsystem: Micro-Star International Co., Ltd.: Unknown device 025c
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32 (8000ns min, 16000ns max), Cache Line Size: 0x10 (64 bytes)
	Interrupt: pin A routed to IRQ 177
	Region 0: I/O ports at 9c00 [size=256]
	Region 1: Memory at f3000000 (32-bit, non-prefetchable) [size=256]
	Expansion ROM at c4000000 [disabled] [size=128K]
	Capabilities: [dc] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-



[-- Attachment #3: dmesg.txt --]
[-- Type: text/plain, Size: 32181 bytes --]

Bootdata ok (command line is root=/dev/sda2 ro )
Linux version 2.6.17-rc4-g0c056c50-dirty (will@zod) (gcc version 4.0.4 20060507 (prerelease) (Debian 4.0.3-3)) #1 PREEMPT Wed May 17 17:04:54 EDT 2006
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
 BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 00000000bfff0000 (usable)
 BIOS-e820: 00000000bfff0000 - 00000000bfff3000 (ACPI NVS)
 BIOS-e820: 00000000bfff3000 - 00000000c0000000 (ACPI data)
 BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fef00000 (reserved)
 BIOS-e820: 00000000fefffc00 - 00000000ff000000 (reserved)
 BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
DMI 2.2 present.
ACPI: RSDP (v000 Nvidia                                ) @ 0x00000000000f7180
ACPI: RSDT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x00000000bfff3000
ACPI: FADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x00000000bfff3040
ACPI: MADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x00000000bfff7a00
ACPI: DSDT (v001 NVIDIA AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x0000000000000000
On node 0 totalpages: 775559
  DMA zone: 3934 pages, LIFO batch:0
  DMA32 zone: 771625 pages, LIFO batch:31
Nvidia board detected. Ignoring ACPI timer override.
ACPI: PM-Timer IO Port: 0x4008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:15 APIC version 16
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: BIOS IRQ0 pin2 override ignored.
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
ACPI: IRQ9 used by override.
ACPI: IRQ14 used by override.
ACPI: IRQ15 used by override.
Setting APIC routing to flat
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at c4000000 (gap: c0000000:3ec00000)
Checking aperture...
CPU 0: aperture @ e8000000 size 128 MB
Built 1 zonelists
Kernel command line: root=/dev/sda2 ro 
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
time.c: Using 3.579545 MHz WALL PM GTOD PIT/TSC timer.
time.c: Detected 1808.816 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
Memory: 3074656k/3145664k available (2945k kernel code, 70268k reserved, 2070k data, 172k init)
Calibrating delay using timer specific routine.. 3618.66 BogoMIPS (lpj=1809333)
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: AMD Athlon(tm) 64 Processor 3000+ stepping 00
Using local APIC timer interrupts.
result 12561230
Detected 12.561 MHz APIC timer.
testing NMI watchdog ... OK.
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using configuration type 1
ACPI: Subsystem revision 20060127
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
ACPI: Power Resource [ISAV] (on)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT]
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNK2] (IRQs *3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LUBA] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LUBB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LMAC] (IRQs *3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LAPU] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LACI] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSMB] (IRQs *3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LUB2] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LFIR] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [L3CM] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSID] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LFID] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [APC1] (IRQs *16), disabled.
ACPI: PCI Interrupt Link [APC2] (IRQs *17), disabled.
ACPI: PCI Interrupt Link [APC3] (IRQs *18), disabled.
ACPI: PCI Interrupt Link [APC4] (IRQs *19), disabled.
ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled.
ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCI] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [AP3C] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0, disabled.
Generic PHY: Registered new driver
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
TC classifier action (bugs to netdev@vger.kernel.org cc hadi@cyberus.ca)
agpgart: Detected AGP bridge 0
agpgart: Setting up Nforce3 AGP.
agpgart: AGP aperture is 128M @ 0xe8000000
PCI-DMA: Disabling IOMMU.
PCI: Bridge: 0000:00:0b.0
  IO window: 8000-8fff
  MEM window: f4000000-f5ffffff
  PREFETCH window: d8000000-e7ffffff
PCI: Bridge: 0000:00:0e.0
  IO window: 9000-9fff
  MEM window: f0000000-f3ffffff
  PREFETCH window: c4000000-c40fffff
PCI: Setting latency timer of device 0000:00:0e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
TCP established hash table entries: 524288 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 524288 bind 65536)
TCP reno registered
IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $
Total HugeTLB memory allocated, 0
fuse init (API version 7.6)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler cfq registered
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
Using specific hotkey driver
Real Time Clock Driver v1.12ac
Linux agpgart interface v0.101 (c) Dave Jones
[drm] Initialized drm 1.0.1 20051102
ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16
GSI 16 sharing vector 0xB1 and IRQ 16
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [APC1] -> GSI 16 (level, low) -> IRQ 177
[drm] Initialized radeon 1.24.0 20060225 on minor 0
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
loop: loaded (max 8 devices)
Marvell 88E1101: Registered new driver
QS6612: Registered new driver
forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.54.
ACPI: PCI Interrupt Link [APCH] enabled at IRQ 23
GSI 17 sharing vector 0xB9 and IRQ 17
ACPI: PCI Interrupt 0000:00:05.0[A] -> Link [APCH] -> GSI 23 (level, high) -> IRQ 185
PCI: Setting latency timer of device 0000:00:05.0 to 64
eth0: forcedeth.c: subsystem: 01462:0250 bound to 0000:00:05.0
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
r8169 Gigabit Ethernet driver 2.2LK-NAPI loaded
ACPI: PCI Interrupt Link [APC5] enabled at IRQ 16
ACPI: PCI Interrupt 0000:02:0d.0[A] -> Link [APC5] -> GSI 16 (level, low) -> IRQ 177
eth1: Identified chip type is 'RTL8169s/8110s'.
eth1: RTL8169 at 0xffffc20000010000, 00:11:09:8f:4b:52, IRQ 177
Linux video capture interface: v1.00
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE3-250: IDE controller at PCI slot 0000:00:08.0
NFORCE3-250: chipset revision 162
NFORCE3-250: not 100% native mode: will probe irqs later
NFORCE3-250: 0000:00:08.0 (rev a2) UDMA133 controller
    ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
    ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hda: PLEXTOR DVDR PX-712A, ATAPI CD/DVD-ROM drive
isa bounce pool size: 16 pages
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
Probing IDE interface ide1...
hda: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 8192kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
libata version 1.20 loaded.
sata_nv 0000:00:09.0: version 0.8
ACPI: PCI Interrupt Link [APSI] enabled at IRQ 22
GSI 18 sharing vector 0xC1 and IRQ 18
ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [APSI] -> GSI 22 (level, high) -> IRQ 193
PCI: Setting latency timer of device 0000:00:09.0 to 64
ata1: SATA max UDMA/133 cmd 0x9E0 ctl 0xBE2 bmdma 0xC800 irq 193
ata2: SATA max UDMA/133 cmd 0x960 ctl 0xB62 bmdma 0xC808 irq 193
ata1: SATA link up 1.5 Gbps (SStatus 113)
ata1: dev 0 cfg 49:2f00 82:346b 83:7f61 84:4003 85:3469 86:3c41 87:4003 88:407f
ata1: dev 0 ATA-6, max UDMA/133, 312581808 sectors: LBA48
nv_sata: Primary device added
nv_sata: Primary device removed
nv_sata: Secondary device added
nv_sata: Secondary device removed
ata1: dev 0 configured for UDMA/133
scsi0 : sata_nv
ata2: SATA link up 1.5 Gbps (SStatus 113)
ata2: dev 0 cfg 49:2f00 82:7c6b 83:7f09 84:4673 85:7c69 86:3e01 87:4663 88:407f
ata2: dev 0 ATA-7, max UDMA/133, 490234752 sectors: LBA48
ata2: dev 0 configured for UDMA/133
scsi1 : sata_nv
  Vendor: ATA       Model: WDC WD1600SD-01K  Rev: 08.0
  Type:   Direct-Access                      ANSI SCSI revision: 05
  Vendor: ATA       Model: Maxtor 6L250S0    Rev: BANC
  Type:   Direct-Access                      ANSI SCSI revision: 05
ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 21
GSI 19 sharing vector 0xC9 and IRQ 19
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [APSJ] -> GSI 21 (level, high) -> IRQ 201
PCI: Setting latency timer of device 0000:00:0a.0 to 64
ata3: SATA max UDMA/133 cmd 0x9F0 ctl 0xBF2 bmdma 0xE000 irq 201
ata4: SATA max UDMA/133 cmd 0x970 ctl 0xB72 bmdma 0xE008 irq 201
ata3: SATA link down (SStatus 0)
scsi2 : sata_nv
ata4: SATA link down (SStatus 0)
scsi3 : sata_nv
SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
 sda: sda1 sda2 sda3
sd 0:0:0:0: Attached scsi disk sda
SCSI device sdb: 490234752 512-byte hdwr sectors (251000 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: drive cache: write back
SCSI device sdb: 490234752 512-byte hdwr sectors (251000 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: drive cache: write back
 sdb: sdb1
sd 1:0:0:0: Attached scsi disk sdb
ieee1394: Initialized config rom entry `ip1394'
ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
GSI 20 sharing vector 0xD1 and IRQ 20
ACPI: PCI Interrupt 0000:02:0c.0[A] -> Link [APC4] -> GSI 19 (level, low) -> IRQ 209
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[209]  MMIO=[f3001000-f30017ff]  Max Packet=[2048]  IR/IT contexts=[4/8]
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 80 td 96
ACPI: PCI Interrupt Link [APCF] enabled at IRQ 20
GSI 21 sharing vector 0xD9 and IRQ 21
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 20 (level, high) -> IRQ 217
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: OHCI Host Controller
drivers/usb/core/inode.c: creating file 'devices'
drivers/usb/core/inode.c: creating file '001'
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:02.0: created debug files
ohci_hcd 0000:00:02.0: irq 217, io mem 0xf6003000
ohci_hcd 0000:00:02.0: resetting from state 'reset', control = 0x600
ohci_hcd 0000:00:02.0: OHCI controller state
ohci_hcd 0000:00:02.0: OHCI 1.0, NO legacy support registers
ohci_hcd 0000:00:02.0: control 0x683 RWE RWC HCFS=operational CBSR=3
ohci_hcd 0000:00:02.0: cmdstatus 0x00000 SOC=0
ohci_hcd 0000:00:02.0: intrstatus 0x00000004 SF
ohci_hcd 0000:00:02.0: intrenable 0x8000000a MIE RD WDH
ohci_hcd 0000:00:02.0: hcca frame #0003
ohci_hcd 0000:00:02.0: roothub.a 01000204 POTPGT=1 NPS NDP=4(4)
ohci_hcd 0000:00:02.0: roothub.b 00000000 PPCM=0000 DR=0000
ohci_hcd 0000:00:02.0: roothub.status 00008000 DRWE
ohci_hcd 0000:00:02.0: roothub.portstatus [0] 0x00000100 PPS
ohci_hcd 0000:00:02.0: roothub.portstatus [1] 0x00000100 PPS
ohci_hcd 0000:00:02.0: roothub.portstatus [2] 0x00000100 PPS
ohci_hcd 0000:00:02.0: roothub.portstatus [3] 0x00000100 PPS
usb usb1: default language 0x0409
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: OHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.17-rc4-g0c056c50-dirty ohci_hcd
usb usb1: SerialNumber: 0000:00:02.0
usb usb1: uevent
usb usb1: configuration #1 chosen from 1 choice
usb usb1: adding 1-0:1.0 (config #1, interface 0)
usb 1-0:1.0: uevent
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: no power switching (usb 1.0)
hub 1-0:1.0: global over-current protection
hub 1-0:1.0: power on to power good time: 2ms
hub 1-0:1.0: local power source is good
hub 1-0:1.0: no over-current condition exists
hub 1-0:1.0: state 7 ports 4 chg 0000 evt 0000
drivers/usb/core/inode.c: creating file '001'
ACPI: PCI Interrupt Link [APCG] enabled at IRQ 23
ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [APCG] -> GSI 23 (level, high) -> IRQ 185
PCI: Setting latency timer of device 0000:00:02.1 to 64
ohci_hcd 0000:00:02.1: OHCI Host Controller
drivers/usb/core/inode.c: creating file '002'
ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:02.1: created debug files
ohci_hcd 0000:00:02.1: irq 185, io mem 0xf6004000
ohci_hcd 0000:00:02.1: resetting from state 'reset', control = 0x600
ohci_hcd 0000:00:02.1: OHCI controller state
ohci_hcd 0000:00:02.1: OHCI 1.0, NO legacy support registers
ohci_hcd 0000:00:02.1: control 0x683 RWE RWC HCFS=operational CBSR=3
ohci_hcd 0000:00:02.1: cmdstatus 0x00000 SOC=0
ohci_hcd 0000:00:02.1: intrstatus 0x00000044 RHSC SF
ohci_hcd 0000:00:02.1: intrenable 0x8000000a MIE RD WDH
ohci_hcd 0000:00:02.1: hcca frame #0003
ohci_hcd 0000:00:02.1: roothub.a 01000204 POTPGT=1 NPS NDP=4(4)
ohci_hcd 0000:00:02.1: roothub.b 00000000 PPCM=0000 DR=0000
ohci_hcd 0000:00:02.1: roothub.status 00008000 DRWE
ohci_hcd 0000:00:02.1: roothub.portstatus [0] 0x00010301 CSC LSDA PPS CCS
ohci_hcd 0000:00:02.1: roothub.portstatus [1] 0x00000100 PPS
ohci_hcd 0000:00:02.1: roothub.portstatus [2] 0x00010101 CSC PPS CCS
ohci_hcd 0000:00:02.1: roothub.portstatus [3] 0x00000100 PPS
usb usb2: default language 0x0409
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: OHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.17-rc4-g0c056c50-dirty ohci_hcd
usb usb2: SerialNumber: 0000:00:02.1
usb usb2: uevent
usb usb2: configuration #1 chosen from 1 choice
usb usb2: adding 2-0:1.0 (config #1, interface 0)
usb 2-0:1.0: uevent
hub 2-0:1.0: usb_probe_interface
hub 2-0:1.0: usb_probe_interface - got id
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 4 ports detected
hub 2-0:1.0: standalone hub
hub 2-0:1.0: no power switching (usb 1.0)
hub 2-0:1.0: global over-current protection
hub 2-0:1.0: power on to power good time: 2ms
hub 2-0:1.0: local power source is good
hub 2-0:1.0: no over-current condition exists
hub 2-0:1.0: state 7 ports 4 chg 0000 evt 0000
drivers/usb/core/inode.c: creating file '001'
ohci_hcd 0000:00:02.1: GetStatus roothub.portstatus [0] = 0x00010301 CSC LSDA PPS CCS
hub 2-0:1.0: port 1, status 0301, change 0001, 1.5 Mb/s
ohci_hcd 0000:00:02.0: suspend root hub
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:02.1: GetStatus roothub.portstatus [0] = 0x00100303 PRSC LSDA PPS PES CCS
usb 2-1: new low speed USB device using ohci_hcd and address 2
ohci_hcd 0000:00:02.1: GetStatus roothub.portstatus [0] = 0x00100303 PRSC LSDA PPS PES CCS
usb 2-1: skipped 1 descriptor after interface
usb 2-1: default language 0x0409
usb 2-1: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 2-1: Product: USB-PS/2 Optical Mouse
usb 2-1: Manufacturer: Logitech
usb 2-1: uevent
usb 2-1: configuration #1 chosen from 1 choice
usb 2-1: adding 2-1:1.0 (config #1, interface 0)
usb 2-1:1.0: uevent
drivers/usb/core/inode.c: creating file '002'
ohci_hcd 0000:00:02.1: GetStatus roothub.portstatus [2] = 0x00010101 CSC PPS CCS
hub 2-0:1.0: port 3, status 0101, change 0001, 12 Mb/s
hub 2-0:1.0: debounce: port 3: total 100ms stable 100ms status 0x101
ohci_hcd 0000:00:02.1: GetStatus roothub.portstatus [2] = 0x00100103 PRSC PPS PES CCS
usb 2-3: new full speed USB device using ohci_hcd and address 3
ohci_hcd 0000:00:02.1: GetStatus roothub.portstatus [2] = 0x00100103 PRSC PPS PES CCS
usb 2-3: ep0 maxpacket = 8
usb 2-3: default language 0x0409
usb 2-3: new device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-3: Product: USB Printer
usb 2-3: Manufacturer: EPSON
usb 2-3: SerialNumber: L41019901181352300
usb 2-3: uevent
usb 2-3: configuration #1 chosen from 1 choice
usb 2-3: adding 2-3:1.0 (config #1, interface 0)
usb 2-3:1.0: uevent
drivers/usb/core/inode.c: creating file '003'
hub 2-0:1.0: state 7 ports 4 chg 0000 evt 0002
usbcore: registered new driver libusual
usbcore: registered new driver hiddev
usbhid 2-1:1.0: usb_probe_interface
usbhid 2-1:1.0: usb_probe_interface - got id
input: Logitech USB-PS/2 Optical Mouse as /class/input/input0
input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:02.1-1
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
input: PC Speaker as /class/input/input1
ieee1394: Host added: ID:BUS[0-00:1023]  GUID[0010dc00006c260b]
input: AT Translated Set 2 keyboard as /class/input/input2
i2c /dev entries driver
EDAC MC: Ver: 2.0.0 May 17 2006
Advanced Linux Sound Architecture Driver Version 1.0.11rc4 (Wed Mar 22 10:27:24 2006 UTC).
ACPI: PCI Interrupt Link [APCJ] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [APCJ] -> GSI 22 (level, high) -> IRQ 193
PCI: Setting latency timer of device 0000:00:06.0 to 64
intel8x0_measure_ac97_clock: measured 50615 usecs
intel8x0: clocking to 46872
ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17
GSI 22 sharing vector 0xE1 and IRQ 22
ACPI: PCI Interrupt 0000:02:0a.0[A] -> Link [APC2] -> GSI 17 (level, low) -> IRQ 225
ALSA device list:
  #0: NVidia CK8S with ALC850 at 0xf6001000, irq 193
  #1: SBLive! Value [CT4670] (rev.5, serial:0x201102) at 0x9000, irq 225
u32 classifier
    Actions configured 
IPv4 over IPv4 tunneling driver
GRE over IPv4 tunneling driver
ip_conntrack version 2.4 (8192 buckets, 65536 max) - 280 bytes per conntrack
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP bic registered
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
NET: Registered protocol family 15
powernow-k8: Found 1 AMD Athlon 64 / Opteron processors (version 1.60.2)
powernow-k8:    0 : fid 0xa (1800 MHz), vid 0x6 (1400 mV)
powernow-k8:    1 : fid 0x2 (1000 MHz), vid 0x12 (1100 mV)
cpu_init done, current fid 0xa, vid 0x6
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
ReiserFS: sda2: found reiserfs format "3.6" with standard journal
ReiserFS: sda2: using ordered data mode
ReiserFS: sda2: journal params: device sda2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sda2: checking transaction log (sda2)
ReiserFS: sda2: Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Freeing unused kernel memory: 172k freed
usb 2-3:1.0: uevent
usb 2-3: uevent
usb 2-1:1.0: uevent
usb 2-1: uevent
usb 2-0:1.0: uevent
usb usb2: uevent
usb 1-0:1.0: uevent
usb usb1: uevent
usblp 2-3:1.0: usb_probe_interface
usblp 2-3:1.0: usb_probe_interface - got id
drivers/usb/core/file.c: looking for a minor, starting at 0
drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 3 if 0 alt 0 proto 2 vid 0x04B8 pid 0x0005
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
i2c_adapter i2c-0: nForce2 SMBus adapter at 0x4c00
i2c_adapter i2c-1: nForce2 SMBus adapter at 0x4c40
ehci_hcd: block sizes: qh 160 qtd 96 itd 192 sitd 96
ACPI: PCI Interrupt Link [APCL] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:02.2[C] -> Link [APCL] -> GSI 21 (level, high) -> IRQ 201
PCI: Setting latency timer of device 0000:00:02.2 to 64
ehci_hcd 0000:00:02.2: EHCI Host Controller
drivers/usb/core/inode.c: creating file '003'
ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 3
ehci_hcd 0000:00:02.2: reset hcs_params 0x102488 dbg=1 cc=2 pcc=4 !ppc ports=8
ehci_hcd 0000:00:02.2: reset portroute 0 0 1 1 1 0 1 0 
ehci_hcd 0000:00:02.2: reset hcc_params a082 caching frame 256/512/1024
ehci_hcd 0000:00:02.2: debug port 1
PCI: cache line size of 64 is not supported by device 0000:00:02.2
ehci_hcd 0000:00:02.2: supports USB remote wakeup
ehci_hcd 0000:00:02.2: irq 201, io mem 0xf6005000
ehci_hcd 0000:00:02.2: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT
ehci_hcd 0000:00:02.2: init command 010009 (park)=0 ithresh=1 period=256 RUN
ehci_hcd 0000:00:02.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb3: default language 0x0409
usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: EHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.17-rc4-g0c056c50-dirty ehci_hcd
usb usb3: SerialNumber: 0000:00:02.2
usb usb3: uevent
usb usb3: configuration #1 chosen from 1 choice
usb usb3: adding 3-0:1.0 (config #1, interface 0)
usb 3-0:1.0: uevent
hub 3-0:1.0: usb_probe_interface
hub 3-0:1.0: usb_probe_interface - got id
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 8 ports detected
hub 3-0:1.0: standalone hub
hub 3-0:1.0: no power switching (usb 1.0)
hub 3-0:1.0: individual port over-current protection
hub 3-0:1.0: Single TT
hub 3-0:1.0: TT requires at most 8 FS bit times (666 ns)
hub 3-0:1.0: power on to power good time: 20ms
hub 3-0:1.0: local power source is good
eth1394: eth2: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
hub 2-0:1.0: state 7 ports 4 chg 0000 evt 000a
ohci_hcd 0000:00:02.1: GetStatus roothub.portstatus [0] = 0x00030300 PESC CSC LSDA PPS
hub 2-0:1.0: port 1, status 0300, change 0003, 1.5 Mb/s
usb 2-1: USB disconnect, address 2
usb 2-1: usb_disable_device nuking all URBs
usb 2-1: unregistering interface 2-1:1.0
usb 2-1:1.0: uevent
usb 2-1: unregistering device
usb 2-1: uevent
drivers/usb/core/inode.c: creating file '001'
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x300
ohci_hcd 0000:00:02.1: GetStatus roothub.portstatus [2] = 0x00030100 PESC CSC PPS
hub 2-0:1.0: port 3, status 0100, change 0003, 12 Mb/s
usb 2-3: USB disconnect, address 3
usb 2-3: usb_disable_device nuking all URBs
usb 2-3: unregistering interface 2-3:1.0
drivers/usb/core/file.c: removing 0 minor
drivers/usb/class/usblp.c: usblp0: removed
usb 2-3:1.0: uevent
usb 2-3: unregistering device
usb 2-3: uevent
hub 2-0:1.0: debounce: port 3: total 100ms stable 100ms status 0x100
hub 3-0:1.0: state 7 ports 8 chg 0000 evt 0000
ehci_hcd 0000:00:02.2: GetStatus port 3 status 001403 POWER sig=k CSC CONNECT
hub 3-0:1.0: port 3, status 0501, change 0001, 480 Mb/s
ohci_hcd 0000:00:02.1: suspend root hub
cx2388x dvb driver version 0.0.5 loaded
CORE cx88[0]: subsystem: 7063:3000, board: pcHDTV HD3000 HDTV [card=22,autodetected]
TV tuner 52 at 0x1fe, Radio tuner -1 at 0x1fe
hub 3-0:1.0: debounce: port 3: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:02.2: port 3 low speed --> companion
ehci_hcd 0000:00:02.2: GetStatus port 3 status 003402 POWER OWNER sig=k CSC
ehci_hcd 0000:00:02.2: GetStatus port 6 status 001803 POWER sig=j CSC CONNECT
hub 3-0:1.0: port 6, status 0501, change 0001, 480 Mb/s
cx2388x v4l2 driver version 0.0.5 loaded
hub 3-0:1.0: debounce: port 6: total 100ms stable 100ms status 0x501
ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18
GSI 23 sharing vector 0xE9 and IRQ 23
ACPI: PCI Interrupt 0000:02:08.2[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 233
cx88[0]/2: found at 0000:02:08.2, rev: 5, irq: 233, latency: 32, mmio: 0xf1000000
cx88[0]/2: cx2388x based dvb card
DVB: registering new adapter (cx88[0]).
DVB: registering frontend 0 (Oren OR51132 VSB/QAM Frontend)...
ACPI: PCI Interrupt 0000:02:08.0[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 233
cx88[0]/0: found at 0000:02:08.0, rev: 5, irq: 233, latency: 32, mmio: 0xf0000000
ehci_hcd 0000:00:02.2: port 6 full speed --> companion
ehci_hcd 0000:00:02.2: GetStatus port 6 status 003001 POWER OWNER sig=se0 CONNECT
hub 3-0:1.0: state 7 ports 8 chg 0000 evt 0000
hub 2-0:1.0: state 7 ports 4 chg 0000 evt 0000, resume root
ohci_hcd 0000:00:02.1: wakeup
ohci_hcd 0000:00:02.1: GetStatus roothub.portstatus [0] = 0x00010301 CSC LSDA PPS CCS
ohci_hcd 0000:00:02.1: GetStatus roothub.portstatus [2] = 0x00010101 CSC PPS CCS
hub 2-0:1.0: state 7 ports 4 chg 0000 evt 0000
ohci_hcd 0000:00:02.1: GetStatus roothub.portstatus [0] = 0x00010301 CSC LSDA PPS CCS
hub 2-0:1.0: port 1, status 0301, change 0001, 1.5 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
tuner 2-0061: chip found @ 0xc2 (cx88[0])
tuner 2-0061: type set to 52 (Thomson DTT 7610 (ATSC/NTSC))
ohci_hcd 0000:00:02.1: GetStatus roothub.portstatus [0] = 0x00100303 PRSC LSDA PPS PES CCS
tda9887 2-0043: chip found @ 0x86 (cx88[0])
cx88[0]/0: registered device video0 [v4l2]
cx88[0]/0: registered device vbi0
cx88[0]/0: registered device radio0
usb 2-1: new low speed USB device using ohci_hcd and address 4
ohci_hcd 0000:00:02.1: GetStatus roothub.portstatus [0] = 0x00100303 PRSC LSDA PPS PES CCS
cx2388x blackbird driver version 0.0.5 loaded
usb 2-1: skipped 1 descriptor after interface
usb 2-1: default language 0x0409
usb 2-1: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 2-1: Product: USB-PS/2 Optical Mouse
usb 2-1: Manufacturer: Logitech
usb 2-1: uevent
usb 2-1: configuration #1 chosen from 1 choice
usb 2-1: adding 2-1:1.0 (config #1, interface 0)
usb 2-1:1.0: uevent
usbhid 2-1:1.0: usb_probe_interface
usbhid 2-1:1.0: usb_probe_interface - got id
input: Logitech USB-PS/2 Optical Mouse as /class/input/input3
input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:02.1-1
drivers/usb/core/inode.c: creating file '004'
ohci_hcd 0000:00:02.1: GetStatus roothub.portstatus [2] = 0x00010101 CSC PPS CCS
hub 2-0:1.0: port 3, status 0101, change 0001, 12 Mb/s
hub 2-0:1.0: debounce: port 3: total 100ms stable 100ms status 0x101
ohci_hcd 0000:00:02.1: GetStatus roothub.portstatus [2] = 0x00100103 PRSC PPS PES CCS
usb 2-3: new full speed USB device using ohci_hcd and address 5
ohci_hcd 0000:00:02.1: GetStatus roothub.portstatus [2] = 0x00100103 PRSC PPS PES CCS
usb 2-3: ep0 maxpacket = 8
usb 2-3: default language 0x0409
usb 2-3: new device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-3: Product: USB Printer
usb 2-3: Manufacturer: EPSON
usb 2-3: SerialNumber: L41019901181352300
usb 2-3: uevent
usb 2-3: configuration #1 chosen from 1 choice
usb 2-3: adding 2-3:1.0 (config #1, interface 0)
usb 2-3:1.0: uevent
usblp 2-3:1.0: usb_probe_interface
usblp 2-3:1.0: usb_probe_interface - got id
drivers/usb/core/file.c: looking for a minor, starting at 0
drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 5 if 0 alt 0 proto 2 vid 0x04B8 pid 0x0005
drivers/usb/core/inode.c: creating file '005'
hub 2-0:1.0: state 7 ports 4 chg 0000 evt 0002
Adding 979956k swap on /dev/sda1.  Priority:-1 extents:1 across:979956k
w83627hf 9191-0290: Reading VID from GPIO5
device-mapper: 4.6.0-ioctl (2006-02-17) initialised: dm-devel@redhat.com
ReiserFS: sda3: found reiserfs format "3.6" with standard journal
ReiserFS: sda3: using ordered data mode
ReiserFS: sda3: journal params: device sda3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sda3: checking transaction log (sda3)
ReiserFS: sda3: Using r5 hash to sort names
ReiserFS: sdb1: found reiserfs format "3.6" with standard journal
ReiserFS: sdb1: using ordered data mode
ReiserFS: sdb1: journal params: device sdb1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sdb1: checking transaction log (sdb1)
ReiserFS: sdb1: Using r5 hash to sort names
ip_conntrack_pptp version 3.1 loaded
ip_nat_pptp version 3.0 loaded
eth0: no IPv6 routers present
agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 4x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 4x mode
[drm] Setting GART location based on new memory map
[drm] Loading R200 Microcode
[drm] writeback test succeeded in 1 usecs
hub 3-0:1.0: state 7 ports 8 chg 0000 evt 0010
ehci_hcd 0000:00:02.2: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 3-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 3-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:02.2: port 4 high speed
ehci_hcd 0000:00:02.2: GetStatus port 4 status 001005 POWER sig=se0 PE CONNECT
usb 3-4: new high speed USB device using ehci_hcd and address 4
usb 3-4: khubd timed out on ep0in len=0/64
usb 3-4: khubd timed out on ep0in len=0/64
usb 3-4: khubd timed out on ep0in len=0/64
ehci_hcd 0000:00:02.2: port 4 high speed
ehci_hcd 0000:00:02.2: GetStatus port 4 status 001005 POWER sig=se0 PE CONNECT
usb 3-4: device descriptor read/64, error -110
usb 3-4: khubd timed out on ep0in len=0/64
usb 3-4: khubd timed out on ep0in len=0/64
usb 3-4: khubd timed out on ep0in len=0/64
ehci_hcd 0000:00:02.2: port 4 high speed
ehci_hcd 0000:00:02.2: GetStatus port 4 status 001005 POWER sig=se0 PE CONNECT
usb 3-4: device descriptor read/64, error -110
ehci_hcd 0000:00:02.2: port 4 high speed
ehci_hcd 0000:00:02.2: GetStatus port 4 status 001005 POWER sig=se0 PE CONNECT
usb 3-4: new high speed USB device using ehci_hcd and address 5
usb 3-4: khubd timed out on ep0in len=0/64
usb 3-4: khubd timed out on ep0in len=0/64
usb 3-4: khubd timed out on ep0in len=0/64
ehci_hcd 0000:00:02.2: port 4 high speed
ehci_hcd 0000:00:02.2: GetStatus port 4 status 001005 POWER sig=se0 PE CONNECT
usb 3-4: device descriptor read/64, error -110
usb 3-4: khubd timed out on ep0in len=0/64
usb 3-4: khubd timed out on ep0in len=0/64
usb 3-4: khubd timed out on ep0in len=0/64
ehci_hcd 0000:00:02.2: GetStatus port 4 status 001002 POWER sig=se0 CSC
hub 3-0:1.0: state 7 ports 8 chg 0000 evt 0010


[-- Attachment #4: dmesg2G.txt --]
[-- Type: text/plain, Size: 33503 bytes --]

Bootdata ok (command line is root=/dev/sda2 mem=2G ro single)
Linux version 2.6.17-rc4-g0c056c50-dirty (will@zod) (gcc version 4.0.4 20060507 (prerelease) (Debian 4.0.3-3)) #1 PREEMPT Wed May 17 17:04:54 EDT 2006
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
 BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 00000000bfff0000 (usable)
 BIOS-e820: 00000000bfff0000 - 00000000bfff3000 (ACPI NVS)
 BIOS-e820: 00000000bfff3000 - 00000000c0000000 (ACPI data)
 BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fef00000 (reserved)
 BIOS-e820: 00000000fefffc00 - 00000000ff000000 (reserved)
 BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
DMI 2.2 present.
ACPI: RSDP (v000 Nvidia                                ) @ 0x00000000000f7180
ACPI: RSDT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x00000000bfff3000
ACPI: FADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x00000000bfff3040
ACPI: MADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x00000000bfff7a00
ACPI: DSDT (v001 NVIDIA AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x0000000000000000
On node 0 totalpages: 517014
  DMA zone: 3934 pages, LIFO batch:0
  DMA32 zone: 513080 pages, LIFO batch:31
Nvidia board detected. Ignoring ACPI timer override.
ACPI: PM-Timer IO Port: 0x4008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:15 APIC version 16
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: BIOS IRQ0 pin2 override ignored.
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
ACPI: IRQ9 used by override.
ACPI: IRQ14 used by override.
ACPI: IRQ15 used by override.
Setting APIC routing to flat
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at c4000000 (gap: c0000000:3ec00000)
Checking aperture...
CPU 0: aperture @ e8000000 size 128 MB
Built 1 zonelists
Kernel command line: root=/dev/sda2 mem=2G ro single
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
time.c: Using 3.579545 MHz WALL PM GTOD PIT/TSC timer.
time.c: Detected 1808.821 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
Memory: 2043744k/2097152k available (2945k kernel code, 52832k reserved, 2070k data, 172k init)
Calibrating delay using timer specific routine.. 3618.66 BogoMIPS (lpj=1809330)
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: AMD Athlon(tm) 64 Processor 3000+ stepping 00
Using local APIC timer interrupts.
result 12561263
Detected 12.561 MHz APIC timer.
testing NMI watchdog ... OK.
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using configuration type 1
ACPI: Subsystem revision 20060127
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
ACPI: Power Resource [ISAV] (on)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT]
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNK2] (IRQs *3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LUBA] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LUBB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LMAC] (IRQs *3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LAPU] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LACI] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSMB] (IRQs *3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LUB2] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LFIR] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [L3CM] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSID] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LFID] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [APC1] (IRQs *16), disabled.
ACPI: PCI Interrupt Link [APC2] (IRQs *17), disabled.
ACPI: PCI Interrupt Link [APC3] (IRQs *18), disabled.
ACPI: PCI Interrupt Link [APC4] (IRQs *19), disabled.
ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled.
ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCI] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [AP3C] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0, disabled.
Generic PHY: Registered new driver
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
TC classifier action (bugs to netdev@vger.kernel.org cc hadi@cyberus.ca)
agpgart: Detected AGP bridge 0
agpgart: Setting up Nforce3 AGP.
agpgart: AGP aperture is 128M @ 0xe8000000
PCI-DMA: Disabling IOMMU.
PCI: Bridge: 0000:00:0b.0
  IO window: 8000-8fff
  MEM window: f4000000-f5ffffff
  PREFETCH window: d8000000-e7ffffff
PCI: Bridge: 0000:00:0e.0
  IO window: 9000-9fff
  MEM window: f0000000-f3ffffff
  PREFETCH window: c4000000-c40fffff
PCI: Setting latency timer of device 0000:00:0e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
TCP established hash table entries: 262144 (order: 9, 2097152 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $
Total HugeTLB memory allocated, 0
fuse init (API version 7.6)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler cfq registered
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
Using specific hotkey driver
Real Time Clock Driver v1.12ac
Linux agpgart interface v0.101 (c) Dave Jones
[drm] Initialized drm 1.0.1 20051102
ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16
GSI 16 sharing vector 0xB1 and IRQ 16
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [APC1] -> GSI 16 (level, low) -> IRQ 177
[drm] Initialized radeon 1.24.0 20060225 on minor 0
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
loop: loaded (max 8 devices)
Marvell 88E1101: Registered new driver
QS6612: Registered new driver
forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.54.
ACPI: PCI Interrupt Link [APCH] enabled at IRQ 23
GSI 17 sharing vector 0xB9 and IRQ 17
ACPI: PCI Interrupt 0000:00:05.0[A] -> Link [APCH] -> GSI 23 (level, high) -> IRQ 185
PCI: Setting latency timer of device 0000:00:05.0 to 64
eth0: forcedeth.c: subsystem: 01462:0250 bound to 0000:00:05.0
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
r8169 Gigabit Ethernet driver 2.2LK-NAPI loaded
ACPI: PCI Interrupt Link [APC5] enabled at IRQ 16
ACPI: PCI Interrupt 0000:02:0d.0[A] -> Link [APC5] -> GSI 16 (level, low) -> IRQ 177
eth1: Identified chip type is 'RTL8169s/8110s'.
eth1: RTL8169 at 0xffffc20000010000, 00:11:09:8f:4b:52, IRQ 177
Linux video capture interface: v1.00
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE3-250: IDE controller at PCI slot 0000:00:08.0
NFORCE3-250: chipset revision 162
NFORCE3-250: not 100% native mode: will probe irqs later
NFORCE3-250: 0000:00:08.0 (rev a2) UDMA133 controller
    ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
    ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hda: PLEXTOR DVDR PX-712A, ATAPI CD/DVD-ROM drive
isa bounce pool size: 16 pages
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
Probing IDE interface ide1...
hda: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 8192kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
libata version 1.20 loaded.
sata_nv 0000:00:09.0: version 0.8
ACPI: PCI Interrupt Link [APSI] enabled at IRQ 22
GSI 18 sharing vector 0xC1 and IRQ 18
ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [APSI] -> GSI 22 (level, high) -> IRQ 193
PCI: Setting latency timer of device 0000:00:09.0 to 64
ata1: SATA max UDMA/133 cmd 0x9E0 ctl 0xBE2 bmdma 0xC800 irq 193
ata2: SATA max UDMA/133 cmd 0x960 ctl 0xB62 bmdma 0xC808 irq 193
ata1: SATA link up 1.5 Gbps (SStatus 113)
ata1: dev 0 cfg 49:2f00 82:346b 83:7f61 84:4003 85:3469 86:3c41 87:4003 88:407f
ata1: dev 0 ATA-6, max UDMA/133, 312581808 sectors: LBA48
nv_sata: Primary device added
nv_sata: Primary device removed
nv_sata: Secondary device added
nv_sata: Secondary device removed
ata1: dev 0 configured for UDMA/133
scsi0 : sata_nv
ata2: SATA link up 1.5 Gbps (SStatus 113)
ata2: dev 0 cfg 49:2f00 82:7c6b 83:7f09 84:4673 85:7c69 86:3e01 87:4663 88:407f
ata2: dev 0 ATA-7, max UDMA/133, 490234752 sectors: LBA48
ata2: dev 0 configured for UDMA/133
scsi1 : sata_nv
  Vendor: ATA       Model: WDC WD1600SD-01K  Rev: 08.0
  Type:   Direct-Access                      ANSI SCSI revision: 05
  Vendor: ATA       Model: Maxtor 6L250S0    Rev: BANC
  Type:   Direct-Access                      ANSI SCSI revision: 05
ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 21
GSI 19 sharing vector 0xC9 and IRQ 19
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [APSJ] -> GSI 21 (level, high) -> IRQ 201
PCI: Setting latency timer of device 0000:00:0a.0 to 64
ata3: SATA max UDMA/133 cmd 0x9F0 ctl 0xBF2 bmdma 0xE000 irq 201
ata4: SATA max UDMA/133 cmd 0x970 ctl 0xB72 bmdma 0xE008 irq 201
ata3: SATA link down (SStatus 0)
scsi2 : sata_nv
ata4: SATA link down (SStatus 0)
scsi3 : sata_nv
SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
 sda: sda1 sda2 sda3
sd 0:0:0:0: Attached scsi disk sda
SCSI device sdb: 490234752 512-byte hdwr sectors (251000 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: drive cache: write back
SCSI device sdb: 490234752 512-byte hdwr sectors (251000 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: drive cache: write back
 sdb: sdb1
sd 1:0:0:0: Attached scsi disk sdb
ieee1394: Initialized config rom entry `ip1394'
ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
GSI 20 sharing vector 0xD1 and IRQ 20
ACPI: PCI Interrupt 0000:02:0c.0[A] -> Link [APC4] -> GSI 19 (level, low) -> IRQ 209
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[209]  MMIO=[f3001000-f30017ff]  Max Packet=[2048]  IR/IT contexts=[4/8]
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 80 td 96
ACPI: PCI Interrupt Link [APCF] enabled at IRQ 20
GSI 21 sharing vector 0xD9 and IRQ 21
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 20 (level, high) -> IRQ 217
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: OHCI Host Controller
drivers/usb/core/inode.c: creating file 'devices'
drivers/usb/core/inode.c: creating file '001'
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:02.0: created debug files
ohci_hcd 0000:00:02.0: irq 217, io mem 0xf6003000
ohci_hcd 0000:00:02.0: resetting from state 'reset', control = 0x600
ohci_hcd 0000:00:02.0: OHCI controller state
ohci_hcd 0000:00:02.0: OHCI 1.0, NO legacy support registers
ohci_hcd 0000:00:02.0: control 0x683 RWE RWC HCFS=operational CBSR=3
ohci_hcd 0000:00:02.0: cmdstatus 0x00000 SOC=0
ohci_hcd 0000:00:02.0: intrstatus 0x00000004 SF
ohci_hcd 0000:00:02.0: intrenable 0x8000000a MIE RD WDH
ohci_hcd 0000:00:02.0: hcca frame #0003
ohci_hcd 0000:00:02.0: roothub.a 01000204 POTPGT=1 NPS NDP=4(4)
ohci_hcd 0000:00:02.0: roothub.b 00000000 PPCM=0000 DR=0000
ohci_hcd 0000:00:02.0: roothub.status 00008000 DRWE
ohci_hcd 0000:00:02.0: roothub.portstatus [0] 0x00000100 PPS
ohci_hcd 0000:00:02.0: roothub.portstatus [1] 0x00000100 PPS
ohci_hcd 0000:00:02.0: roothub.portstatus [2] 0x00000100 PPS
ohci_hcd 0000:00:02.0: roothub.portstatus [3] 0x00000100 PPS
usb usb1: default language 0x0409
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: OHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.17-rc4-g0c056c50-dirty ohci_hcd
usb usb1: SerialNumber: 0000:00:02.0
usb usb1: uevent
usb usb1: configuration #1 chosen from 1 choice
usb usb1: adding 1-0:1.0 (config #1, interface 0)
usb 1-0:1.0: uevent
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: no power switching (usb 1.0)
hub 1-0:1.0: global over-current protection
hub 1-0:1.0: power on to power good time: 2ms
hub 1-0:1.0: local power source is good
hub 1-0:1.0: no over-current condition exists
hub 1-0:1.0: state 7 ports 4 chg 0000 evt 0000
drivers/usb/core/inode.c: creating file '001'
ACPI: PCI Interrupt Link [APCG] enabled at IRQ 23
ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [APCG] -> GSI 23 (level, high) -> IRQ 185
PCI: Setting latency timer of device 0000:00:02.1 to 64
ohci_hcd 0000:00:02.1: OHCI Host Controller
drivers/usb/core/inode.c: creating file '002'
ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:02.1: created debug files
ohci_hcd 0000:00:02.1: irq 185, io mem 0xf6004000
ohci_hcd 0000:00:02.1: resetting from state 'reset', control = 0x600
ohci_hcd 0000:00:02.1: OHCI controller state
ohci_hcd 0000:00:02.1: OHCI 1.0, NO legacy support registers
ohci_hcd 0000:00:02.1: control 0x683 RWE RWC HCFS=operational CBSR=3
ohci_hcd 0000:00:02.1: cmdstatus 0x00000 SOC=0
ohci_hcd 0000:00:02.1: intrstatus 0x00000044 RHSC SF
ohci_hcd 0000:00:02.1: intrenable 0x8000000a MIE RD WDH
ohci_hcd 0000:00:02.1: hcca frame #0003
ohci_hcd 0000:00:02.1: roothub.a 01000204 POTPGT=1 NPS NDP=4(4)
ohci_hcd 0000:00:02.1: roothub.b 00000000 PPCM=0000 DR=0000
ohci_hcd 0000:00:02.1: roothub.status 00008000 DRWE
ohci_hcd 0000:00:02.1: roothub.portstatus [0] 0x00010301 CSC LSDA PPS CCS
ohci_hcd 0000:00:02.1: roothub.portstatus [1] 0x00000100 PPS
ohci_hcd 0000:00:02.1: roothub.portstatus [2] 0x00010101 CSC PPS CCS
ohci_hcd 0000:00:02.1: roothub.portstatus [3] 0x00000100 PPS
usb usb2: default language 0x0409
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: OHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.17-rc4-g0c056c50-dirty ohci_hcd
usb usb2: SerialNumber: 0000:00:02.1
usb usb2: uevent
usb usb2: configuration #1 chosen from 1 choice
usb usb2: adding 2-0:1.0 (config #1, interface 0)
usb 2-0:1.0: uevent
hub 2-0:1.0: usb_probe_interface
hub 2-0:1.0: usb_probe_interface - got id
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 4 ports detected
hub 2-0:1.0: standalone hub
hub 2-0:1.0: no power switching (usb 1.0)
hub 2-0:1.0: global over-current protection
hub 2-0:1.0: power on to power good time: 2ms
hub 2-0:1.0: local power source is good
hub 2-0:1.0: no over-current condition exists
hub 2-0:1.0: state 7 ports 4 chg 0000 evt 0000
drivers/usb/core/inode.c: creating file '001'
ohci_hcd 0000:00:02.1: GetStatus roothub.portstatus [0] = 0x00010301 CSC LSDA PPS CCS
hub 2-0:1.0: port 1, status 0301, change 0001, 1.5 Mb/s
ohci_hcd 0000:00:02.0: suspend root hub
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:02.1: GetStatus roothub.portstatus [0] = 0x00100303 PRSC LSDA PPS PES CCS
usb 2-1: new low speed USB device using ohci_hcd and address 2
ohci_hcd 0000:00:02.1: GetStatus roothub.portstatus [0] = 0x00100303 PRSC LSDA PPS PES CCS
usb 2-1: skipped 1 descriptor after interface
usb 2-1: default language 0x0409
usb 2-1: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 2-1: Product: USB-PS/2 Optical Mouse
usb 2-1: Manufacturer: Logitech
usb 2-1: uevent
usb 2-1: configuration #1 chosen from 1 choice
usb 2-1: adding 2-1:1.0 (config #1, interface 0)
usb 2-1:1.0: uevent
drivers/usb/core/inode.c: creating file '002'
ohci_hcd 0000:00:02.1: GetStatus roothub.portstatus [2] = 0x00010101 CSC PPS CCS
hub 2-0:1.0: port 3, status 0101, change 0001, 12 Mb/s
hub 2-0:1.0: debounce: port 3: total 100ms stable 100ms status 0x101
ohci_hcd 0000:00:02.1: GetStatus roothub.portstatus [2] = 0x00100103 PRSC PPS PES CCS
usb 2-3: new full speed USB device using ohci_hcd and address 3
ohci_hcd 0000:00:02.1: GetStatus roothub.portstatus [2] = 0x00100103 PRSC PPS PES CCS
usb 2-3: ep0 maxpacket = 8
usb 2-3: default language 0x0409
usb 2-3: new device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-3: Product: USB Printer
usb 2-3: Manufacturer: EPSON
usb 2-3: SerialNumber: L41019901181352300
usb 2-3: uevent
usb 2-3: configuration #1 chosen from 1 choice
usb 2-3: adding 2-3:1.0 (config #1, interface 0)
usb 2-3:1.0: uevent
drivers/usb/core/inode.c: creating file '003'
hub 2-0:1.0: state 7 ports 4 chg 0000 evt 0002
usbcore: registered new driver libusual
usbcore: registered new driver hiddev
usbhid 2-1:1.0: usb_probe_interface
usbhid 2-1:1.0: usb_probe_interface - got id
input: Logitech USB-PS/2 Optical Mouse as /class/input/input0
input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:02.1-1
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
input: PC Speaker as /class/input/input1
ieee1394: Host added: ID:BUS[0-00:1023]  GUID[0010dc00006c260b]
input: AT Translated Set 2 keyboard as /class/input/input2
i2c /dev entries driver
EDAC MC: Ver: 2.0.0 May 17 2006
Advanced Linux Sound Architecture Driver Version 1.0.11rc4 (Wed Mar 22 10:27:24 2006 UTC).
ACPI: PCI Interrupt Link [APCJ] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [APCJ] -> GSI 22 (level, high) -> IRQ 193
PCI: Setting latency timer of device 0000:00:06.0 to 64
intel8x0_measure_ac97_clock: measured 50623 usecs
intel8x0: clocking to 46879
ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17
GSI 22 sharing vector 0xE1 and IRQ 22
ACPI: PCI Interrupt 0000:02:0a.0[A] -> Link [APC2] -> GSI 17 (level, low) -> IRQ 225
ALSA device list:
  #0: NVidia CK8S with ALC850 at 0xf6001000, irq 193
  #1: SBLive! Value [CT4670] (rev.5, serial:0x201102) at 0x9000, irq 225
u32 classifier
    Actions configured 
IPv4 over IPv4 tunneling driver
GRE over IPv4 tunneling driver
ip_conntrack version 2.4 (8192 buckets, 65536 max) - 280 bytes per conntrack
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP bic registered
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
NET: Registered protocol family 15
powernow-k8: Found 1 AMD Athlon 64 / Opteron processors (version 1.60.2)
powernow-k8:    0 : fid 0xa (1800 MHz), vid 0x6 (1400 mV)
powernow-k8:    1 : fid 0x2 (1000 MHz), vid 0x12 (1100 mV)
cpu_init done, current fid 0xa, vid 0x6
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
ReiserFS: sda2: found reiserfs format "3.6" with standard journal
ReiserFS: sda2: using ordered data mode
ReiserFS: sda2: journal params: device sda2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sda2: checking transaction log (sda2)
ReiserFS: sda2: Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Freeing unused kernel memory: 172k freed
usb 2-3:1.0: uevent
usb 2-3: uevent
usb 2-1:1.0: uevent
usb 2-1: uevent
usb 2-0:1.0: uevent
usb usb2: uevent
usb 1-0:1.0: uevent
usb usb1: uevent
i2c_adapter i2c-0: nForce2 SMBus adapter at 0x4c00
i2c_adapter i2c-1: nForce2 SMBus adapter at 0x4c40
eth1394: eth2: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
ehci_hcd: block sizes: qh 160 qtd 96 itd 192 sitd 96
ACPI: PCI Interrupt Link [APCL] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:02.2[C] -> Link [APCL] -> GSI 21 (level, high) -> IRQ 201
PCI: Setting latency timer of device 0000:00:02.2 to 64
ehci_hcd 0000:00:02.2: EHCI Host Controller
drivers/usb/core/inode.c: creating file '003'
ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 3
ehci_hcd 0000:00:02.2: reset hcs_params 0x102488 dbg=1 cc=2 pcc=4 !ppc ports=8
ehci_hcd 0000:00:02.2: reset portroute 0 0 1 1 1 0 1 0 
ehci_hcd 0000:00:02.2: reset hcc_params a082 caching frame 256/512/1024
ehci_hcd 0000:00:02.2: debug port 1
PCI: cache line size of 64 is not supported by device 0000:00:02.2
ehci_hcd 0000:00:02.2: supports USB remote wakeup
ehci_hcd 0000:00:02.2: irq 201, io mem 0xf6005000
ehci_hcd 0000:00:02.2: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT
ehci_hcd 0000:00:02.2: init command 010009 (park)=0 ithresh=1 period=256 RUN
ehci_hcd 0000:00:02.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb3: default language 0x0409
usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: EHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.17-rc4-g0c056c50-dirty ehci_hcd
usb usb3: SerialNumber: 0000:00:02.2
usb usb3: uevent
usb usb3: configuration #1 chosen from 1 choice
usb usb3: adding 3-0:1.0 (config #1, interface 0)
usb 3-0:1.0: uevent
hub 3-0:1.0: usb_probe_interface
hub 3-0:1.0: usb_probe_interface - got id
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 8 ports detected
hub 3-0:1.0: standalone hub
hub 3-0:1.0: no power switching (usb 1.0)
hub 3-0:1.0: individual port over-current protection
hub 3-0:1.0: Single TT
hub 3-0:1.0: TT requires at most 8 FS bit times (666 ns)
hub 3-0:1.0: power on to power good time: 20ms
hub 3-0:1.0: local power source is good
usblp 2-3:1.0: usb_probe_interface
usblp 2-3:1.0: usb_probe_interface - got id
ohci_hcd 0000:00:02.1: urb ffff81007ee24b00 path 3 ep0out 5ec20000 cc 5 --> status -110
drivers/usb/class/usblp.c: can't set desired altsetting 0 on interface 0
usblp: probe of 2-3:1.0 failed with error -5
hub 2-0:1.0: state 7 ports 4 chg 0000 evt 000a
ohci_hcd 0000:00:02.1: GetStatus roothub.portstatus [0] = 0x00030300 PESC CSC LSDA PPS
hub 2-0:1.0: port 1, status 0300, change 0003, 1.5 Mb/s
usb 2-1: USB disconnect, address 2
usb 2-1: usb_disable_device nuking all URBs
usb 2-1: unregistering interface 2-1:1.0
usb 2-1:1.0: uevent
usb 2-1: unregistering device
usb 2-1: uevent
drivers/usb/core/inode.c: creating file '001'
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x300
ohci_hcd 0000:00:02.1: GetStatus roothub.portstatus [2] = 0x00030100 PESC CSC PPS
hub 2-0:1.0: port 3, status 0100, change 0003, 12 Mb/s
usb 2-3: USB disconnect, address 3
usb 2-3: usb_disable_device nuking all URBs
usb 2-3: unregistering interface 2-3:1.0
usb 2-3:1.0: uevent
usb 2-3: unregistering device
usb 2-3: uevent
cx2388x dvb driver version 0.0.5 loaded
CORE cx88[0]: subsystem: 7063:3000, board: pcHDTV HD3000 HDTV [card=22,autodetected]
TV tuner 52 at 0x1fe, Radio tuner -1 at 0x1fe
cx2388x v4l2 driver version 0.0.5 loaded
hub 2-0:1.0: debounce: port 3: total 100ms stable 100ms status 0x100
hub 3-0:1.0: state 7 ports 8 chg 0000 evt 0000
ehci_hcd 0000:00:02.2: GetStatus port 3 status 001403 POWER sig=k CSC CONNECT
hub 3-0:1.0: port 3, status 0501, change 0001, 480 Mb/s
ohci_hcd 0000:00:02.1: suspend root hub
hub 3-0:1.0: debounce: port 3: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:02.2: port 3 low speed --> companion
ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18
GSI 23 sharing vector 0xE9 and IRQ 23
ACPI: PCI Interrupt 0000:02:08.2[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 233
cx88[0]/2: found at 0000:02:08.2, rev: 5, irq: 233, latency: 32, mmio: 0xf1000000
cx88[0]/2: cx2388x based dvb card
DVB: registering new adapter (cx88[0]).
DVB: registering frontend 0 (Oren OR51132 VSB/QAM Frontend)...
ACPI: PCI Interrupt 0000:02:08.0[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 233
cx88[0]/0: found at 0000:02:08.0, rev: 5, irq: 233, latency: 32, mmio: 0xf0000000
ehci_hcd 0000:00:02.2: GetStatus port 3 status 003402 POWER OWNER sig=k CSC
ehci_hcd 0000:00:02.2: GetStatus port 6 status 001803 POWER sig=j CSC CONNECT
hub 3-0:1.0: port 6, status 0501, change 0001, 480 Mb/s
tuner 2-0061: chip found @ 0xc2 (cx88[0])
tuner 2-0061: type set to 52 (Thomson DTT 7610 (ATSC/NTSC))
tda9887 2-0043: chip found @ 0x86 (cx88[0])
cx88[0]/0: registered device video0 [v4l2]
cx88[0]/0: registered device vbi0
cx88[0]/0: registered device radio0
cx2388x blackbird driver version 0.0.5 loaded
hub 3-0:1.0: debounce: port 6: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:02.2: port 6 full speed --> companion
ehci_hcd 0000:00:02.2: GetStatus port 6 status 003001 POWER OWNER sig=se0 CONNECT
hub 3-0:1.0: state 7 ports 8 chg 0000 evt 0000
hub 2-0:1.0: state 7 ports 4 chg 0000 evt 0000, resume root
ohci_hcd 0000:00:02.1: wakeup
ohci_hcd 0000:00:02.1: GetStatus roothub.portstatus [0] = 0x00010301 CSC LSDA PPS CCS
ohci_hcd 0000:00:02.1: GetStatus roothub.portstatus [2] = 0x00010101 CSC PPS CCS
hub 2-0:1.0: state 7 ports 4 chg 0000 evt 0000
ohci_hcd 0000:00:02.1: GetStatus roothub.portstatus [0] = 0x00010301 CSC LSDA PPS CCS
hub 2-0:1.0: port 1, status 0301, change 0001, 1.5 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:02.1: GetStatus roothub.portstatus [0] = 0x00100303 PRSC LSDA PPS PES CCS
usb 2-1: new low speed USB device using ohci_hcd and address 4
ohci_hcd 0000:00:02.1: GetStatus roothub.portstatus [0] = 0x00100303 PRSC LSDA PPS PES CCS
usb 2-1: skipped 1 descriptor after interface
usb 2-1: default language 0x0409
usb 2-1: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 2-1: Product: USB-PS/2 Optical Mouse
usb 2-1: Manufacturer: Logitech
usb 2-1: uevent
usb 2-1: configuration #1 chosen from 1 choice
usb 2-1: adding 2-1:1.0 (config #1, interface 0)
usb 2-1:1.0: uevent
usbhid 2-1:1.0: usb_probe_interface
usbhid 2-1:1.0: usb_probe_interface - got id
input: Logitech USB-PS/2 Optical Mouse as /class/input/input3
input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:02.1-1
drivers/usb/core/inode.c: creating file '004'
ohci_hcd 0000:00:02.1: GetStatus roothub.portstatus [2] = 0x00010101 CSC PPS CCS
hub 2-0:1.0: port 3, status 0101, change 0001, 12 Mb/s
hub 2-0:1.0: debounce: port 3: total 100ms stable 100ms status 0x101
Adding 979956k swap on /dev/sda1.  Priority:-1 extents:1 across:979956k
ohci_hcd 0000:00:02.1: GetStatus roothub.portstatus [2] = 0x00100103 PRSC PPS PES CCS
usb 2-3: new full speed USB device using ohci_hcd and address 5
ohci_hcd 0000:00:02.1: GetStatus roothub.portstatus [2] = 0x00100103 PRSC PPS PES CCS
usb 2-3: ep0 maxpacket = 8
usb 2-3: default language 0x0409
usb 2-3: new device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-3: Product: USB Printer
usb 2-3: Manufacturer: EPSON
usb 2-3: SerialNumber: L41019901181352300
usb 2-3: uevent
usb 2-3: configuration #1 chosen from 1 choice
usb 2-3: adding 2-3:1.0 (config #1, interface 0)
usb 2-3:1.0: uevent
usblp 2-3:1.0: usb_probe_interface
usblp 2-3:1.0: usb_probe_interface - got id
drivers/usb/core/file.c: looking for a minor, starting at 0
drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 5 if 0 alt 0 proto 2 vid 0x04B8 pid 0x0005
drivers/usb/core/inode.c: creating file '005'
hub 2-0:1.0: state 7 ports 4 chg 0000 evt 0002
w83627hf 9191-0290: Reading VID from GPIO5
device-mapper: 4.6.0-ioctl (2006-02-17) initialised: dm-devel@redhat.com
ReiserFS: sda3: found reiserfs format "3.6" with standard journal
ReiserFS: sda3: using ordered data mode
ReiserFS: sda3: journal params: device sda3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sda3: checking transaction log (sda3)
ReiserFS: sda3: Using r5 hash to sort names
ReiserFS: sdb1: found reiserfs format "3.6" with standard journal
ReiserFS: sdb1: using ordered data mode
ReiserFS: sdb1: journal params: device sdb1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sdb1: checking transaction log (sdb1)
ReiserFS: sdb1: Using r5 hash to sort names
ip_conntrack_pptp version 3.1 loaded
ip_nat_pptp version 3.0 loaded
eth0: no IPv6 routers present
hub 3-0:1.0: state 7 ports 8 chg 0000 evt 0010
ehci_hcd 0000:00:02.2: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT
hub 3-0:1.0: port 4, status 0501, change 0001, 480 Mb/s
hub 3-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:02.2: port 4 high speed
ehci_hcd 0000:00:02.2: GetStatus port 4 status 001005 POWER sig=se0 PE CONNECT
usb 3-4: new high speed USB device using ehci_hcd and address 4
ehci_hcd 0000:00:02.2: port 4 high speed
ehci_hcd 0000:00:02.2: GetStatus port 4 status 001005 POWER sig=se0 PE CONNECT
usb 3-4: new device strings: Mfr=0, Product=0, SerialNumber=0
usb 3-4: uevent
usb 3-4: configuration #1 chosen from 1 choice
usb 3-4: adding 3-4:1.0 (config #1, interface 0)
usb 3-4:1.0: uevent
hub 3-4:1.0: usb_probe_interface
hub 3-4:1.0: usb_probe_interface - got id
hub 3-4:1.0: USB hub found
hub 3-4:1.0: 4 ports detected
hub 3-4:1.0: standalone hub
hub 3-4:1.0: individual port power switching
hub 3-4:1.0: individual port over-current protection
hub 3-4:1.0: TT per port
hub 3-4:1.0: TT requires at most 8 FS bit times (666 ns)
hub 3-4:1.0: Port indicators are supported
hub 3-4:1.0: power on to power good time: 100ms
hub 3-4:1.0: local power source is good
hub 3-4:1.0: enabling power on all ports
usb 3-4: link qh256-0001/ffff81007e665140 start 255 [1/0 us]
drivers/usb/core/inode.c: creating file '004'
hub 3-4:1.0: state 7 ports 4 chg 0000 evt 0000
hub 3-4:1.0: state 7 ports 4 chg 0000 evt 0008
hub 3-4:1.0: port 3, status 0101, change 0001, 12 Mb/s
hub 3-4:1.0: debounce: port 3: total 100ms stable 100ms status 0x101
hub 3-4:1.0: port 3 not reset yet, waiting 10ms
usb 3-4.3: new high speed USB device using ehci_hcd and address 5
hub 3-4:1.0: port 3 not reset yet, waiting 10ms
usb 3-4.3: default language 0x0409
usb 3-4.3: new device strings: Mfr=1, Product=2, SerialNumber=3
usb 3-4.3: Product: iPod
usb 3-4.3: Manufacturer: Apple
usb 3-4.3: SerialNumber: 000A2700129D2D99
usb 3-4.3: uevent
usb 3-4.3: configuration #1 chosen from 1 choice
usb 3-4.3: adding 3-4.3:1.0 (config #1, interface 0)
usb 3-4.3:1.0: uevent
libusual 3-4.3:1.0: usb_probe_interface
libusual 3-4.3:1.0: usb_probe_interface - got id
drivers/usb/core/inode.c: creating file '005'
Initializing USB Mass Storage driver...
usb-storage 3-4.3:1.0: usb_probe_interface
usb-storage 3-4.3:1.0: usb_probe_interface - got id
scsi4 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 5
usb-storage: waiting for device to settle before scanning
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
  Vendor: Apple     Model: iPod              Rev: 1.62
  Type:   Direct-Access                      ANSI SCSI revision: 00
SCSI device sdc: 3999743 512-byte hdwr sectors (2048 MB)
sdc: Write Protect is off
sdc: Mode Sense: 68 00 00 08
sdc: assuming drive cache: write through
SCSI device sdc: 3999743 512-byte hdwr sectors (2048 MB)
sdc: Write Protect is off
sdc: Mode Sense: 68 00 00 08
sdc: assuming drive cache: write through
 sdc: sdc1 sdc2
sd 4:0:0:0: Attached scsi removable disk sdc
usb-storage: device scan complete
agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 4x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 4x mode
[drm] Setting GART location based on new memory map
[drm] Loading R200 Microcode
[drm] writeback test succeeded in 1 usecs

Re: USB 2.0 ehci failure with large amount of RAM (4GB) on x86_64

[Biker]

Hi all,
I've been hitting this bug (or a similar one) for the last few months; it also 
happens on 32 bits with 1 GB of RAM. My system is a somewhat old Athlon, 
coupled with a VIA chipset and an ALI USB 2.0 PCI card.
Whenever I plug in my creative muvo tx 1GB I get the following messages:

May 17 00:05:15 hiddenplace hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0008
May 17 00:05:15 hiddenplace ehci_hcd 0000:00:0a.3: GetStatus port 3 status 
001803 POWER sig=j CSC CONNECT
May 17 00:05:15 hiddenplace hub 4-0:1.0: port 3, status 0501, change 0001, 480 
Mb/s
May 17 00:05:15 hiddenplace hub 4-0:1.0: debounce: port 3: total 100ms stable 
100ms status 0x501
May 17 00:05:15 hiddenplace ehci_hcd 0000:00:0a.3: port 3 high speed
May 17 00:05:15 hiddenplace ehci_hcd 0000:00:0a.3: GetStatus port 3 status 
001005 POWER sig=se0 PE CONNECT
May 17 00:05:15 hiddenplace usb 4-3: new high speed USB device using ehci_hcd 
and address 7
May 17 00:05:15 hiddenplace ehci_hcd 0000:00:0a.3: devpath 3 ep0out 3strikes
May 17 00:05:15 hiddenplace ehci_hcd 0000:00:0a.3: devpath 3 ep0out 3strikes
May 17 00:05:16 hiddenplace usb 4-3: device not accepting address 7, error -71
May 17 00:05:16 hiddenplace ehci_hcd 0000:00:0a.3: port 3 high speed
May 17 00:05:16 hiddenplace ehci_hcd 0000:00:0a.3: GetStatus port 3 status 
001005 POWER sig=se0 PE CONNECT
May 17 00:05:16 hiddenplace usb 4-3: new high speed USB device using ehci_hcd 
and address 8
May 17 00:05:16 hiddenplace ehci_hcd 0000:00:0a.3: devpath 3 ep0out 3strikes
May 17 00:05:16 hiddenplace ehci_hcd 0000:00:0a.3: devpath 3 ep0out 3strikes
May 17 00:05:16 hiddenplace usb 4-3: device not accepting address 8, error -71
[output omitted]

If I rmmod ehci_hcd then ohci_hcd kicks in and it works, albeit at 12 MB/s.
I'm using the nvidia proprietary module and ndiswrapper, but removing them and 
rebooting to an untainted kernel does not change anything.

Thanks in advance for your help, please CC: me as I'm not subscribed.

Best regards, Silla

# uname -a
Linux hiddenplace 2.6.16-gentoo-r7 #1 PREEMPT Wed May 10 21:14:35 CEST 2006 
i686 AMD Athlon(tm) XP 1600+ GNU/Linux

# lspci
00:00.0 Host bridge: VIA Technologies, Inc. VT8366/A/7 [Apollo KT266/A/333]
00:01.0 PCI bridge: VIA Technologies, Inc. VT8366/A/7 [Apollo KT266/A/333 AGP]
00:08.0 Multimedia audio controller: Creative Labs SB Live! EMU10k1 (rev 06)
00:08.1 Input device controller: Creative Labs SB Live! MIDI/Game Port (rev 
06)
00:0a.0 USB Controller: ALi Corporation USB 1.1 Controller (rev 03)
00:0a.1 USB Controller: ALi Corporation USB 1.1 Controller (rev 03)
00:0a.2 USB Controller: ALi Corporation USB 1.1 Controller (rev 03)
00:0a.3 USB Controller: ALi Corporation USB 2.0 Controller (rev 01)
00:0b.0 Network controller: Broadcom Corporation BCM4306 802.11b/g Wireless 
LAN Controller (rev 03)
00:0d.0 Ethernet controller: 3Com Corporation 3c905 100BaseTX [Boomerang]
00:11.0 ISA bridge: VIA Technologies, Inc. VT8233 PCI to ISA Bridge
00:11.1 IDE interface: VIA Technologies, Inc. 
VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
00:11.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 
Controller (rev 1b)
00:11.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 
Controller (rev 1b)
01:00.0 VGA compatible controller: nVidia Corporation NV11DDR [GeForce2 MX 100 
DDR/200 DDR] (rev b2)

# cat /proc/interrupts
           CPU0
  0:     276293          XT-PIC  timer
  2:          0          XT-PIC  cascade
  7:         34          XT-PIC  ehci_hcd:usb4
  9:          0          XT-PIC  acpi
 10:      58405          XT-PIC  ohci_hcd:usb1, uhci_hcd:usb5, uhci_hcd:usb6
 11:          0          XT-PIC  EMU10K1, ohci_hcd:usb2, ohci_hcd:usb3
 14:       3333          XT-PIC  ide0
 15:       4382          XT-PIC  ide1
NMI:          0
ERR:          0

# cat /var/log/dmesg
Linux version 2.6.16-gentoo-r7 (root@hiddenplace) (gcc version 3.4.5 (Gentoo 
3.4.5-r1, ssp-3.4.5-1.0, pie-8.7.9)) #1 PREEMPT Wed May 10 21:14:35 CEST 2006
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000003fff0000 (usable)
 BIOS-e820: 000000003fff0000 - 000000003fff3000 (ACPI NVS)
 BIOS-e820: 000000003fff3000 - 0000000040000000 (ACPI data)
 BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
127MB HIGHMEM available.
896MB LOWMEM available.
On node 0 totalpages: 262128
  DMA zone: 4096 pages, LIFO batch:0
  DMA32 zone: 0 pages, LIFO batch:0
  Normal zone: 225280 pages, LIFO batch:31
  HighMem zone: 32752 pages, LIFO batch:7
DMI 2.2 present.
ACPI: RSDP (v000 VIA694                                ) @ 0x000f7290
ACPI: RSDT (v001 VIA694 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x3fff3000
ACPI: FADT (v001 VIA694 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x3fff3040
ACPI: DSDT (v001 VIA694 AWRDACPI 0x00001000 MSFT 0x0100000c) @ 0x00000000
ACPI: PM-Timer IO Port: 0x4008
Allocating PCI resources starting at 50000000 (gap: 40000000:bfff0000)
Built 1 zonelists
Kernel command line: root=/dev/hda3
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 1403.365 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1036144k/1048512k available (1859k kernel code, 11776k reserved, 553k 
data, 128k init, 131008k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 2809.46 BogoMIPS 
(lpj=1404733)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0383f9ff c1c3f9ff 00000000 00000000 
00000000 00000000 00000000
CPU: After vendor identify, caps: 0383f9ff c1c3f9ff 00000000 00000000 00000000 
00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After all inits, caps: 0383f9ff c1c3f9ff 00000000 00000420 00000000 
00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: AMD Athlon(tm) XP 1600+ stepping 02
Checking 'hlt' instruction... OK.
ACPI: setting ELCR to 0200 (from 0e80)
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfb480, last bus=1
PCI: Using configuration type 1
ACPI: Subsystem revision 20060127
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 *7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 *10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 11 devices
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
TC classifier action (bugs to netdev@vger.kernel.org cc hadi@cyberus.ca)
PCI: Bridge: 0000:00:01.0
  IO window: disabled.
  MEM window: ec000000-edffffff
  PREFETCH window: e0000000-e7ffffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
Machine check exception polling timer started.
audit: initializing netlink socket (disabled)
audit(1147817373.641:1): initialized
highmem bounce pool size: 64 pages
SGI XFS with no debug enabled
Initializing Cryptographic API
io scheduler noop registered
io scheduler cfq registered (default)
 0000:00:11.2: uhci_check_and_reset_hc: legsup = 0x003a
 0000:00:11.2: Performing full reset
 0000:00:11.3: uhci_check_and_reset_hc: legsup = 0x0010
 0000:00:11.3: Performing full reset
vesafb: NVidia Corporation, NV11 Board, Chip Rev B2 (OEM: NVidia)
vesafb: VBE version: 3.0
vesafb: VBIOS/hardware supports DDC2 transfers
vesafb: monitor limits: vf = 200 Hz, hf = 107 kHz, clk = 230 MHz
vesafb: scrolling: redraw
Console: switching to colour frame buffer device 128x48
vesafb: framebuffer at 0xe0000000, mapped to 0xf8880000, using 7500k, total 
32768k
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:11.1
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:11.1[A] -> Link [LNKA] -> GSI 11 (level, low) -> 
IRQ 11
PCI: Via IRQ fixup for 0000:00:11.1, from 255 to 11
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8233 (rev 00) IDE UDMA100 controller on pci0000:00:11.1
    ide0: BM-DMA at 0xdc00-0xdc07, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0xdc08-0xdc0f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: MAXTOR 6L040J2, ATA DISK drive
hdb: Maxtor 6L300R0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: MATSHITADVD-ROM SR-8587, ATAPI CD/DVD-ROM drive
hdd: HL-DT-ST DVDRAM GSA-4163B, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 78177792 sectors (40027 MB) w/1818KiB Cache, CHS=65535/16/63, UDMA(100)
hda: cache flushes supported
 hda: hda1 hda2 hda3
hdb: max request size: 512KiB
hdb: 586114704 sectors (300090 MB) w/16384KiB Cache, CHS=36483/255/63, 
UDMA(100)
hdb: cache flushes supported
 hdb: hdb1
NET: Registered protocol family 2
IP route cache hash table entries: 65536 (order: 6, 262144 bytes)
TCP established hash table entries: 262144 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
TCP bic registered
Using IPI Shortcut mode
XFS mounting filesystem hda3
Ending clean XFS mount for filesystem: hda3
VFS: Mounted root (xfs filesystem) readonly.
Freeing unused kernel memory: 128k freed
NET: Registered protocol family 1
Adding 506036k swap on /dev/hda2.  Priority:-1 extents:1 across:506036k
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
hdc: ATAPI 48X DVD-ROM drive, 256kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
hdd: ATAPI 40X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
NET: Registered protocol family 17
XFS mounting filesystem hdb1
Ending clean XFS mount for filesystem: hdb1
usbcore: registered new driver usbfs
usbcore: registered new driver hub
TCP westwood registered