* MDI errors during resume from ACPI S3 (suspend to ram)
@ 2019-08-06 15:36 Paul Menzel
2019-08-06 15:53 ` Mario.Limonciello
0 siblings, 1 reply; 5+ messages in thread
From: Paul Menzel @ 2019-08-06 15:36 UTC (permalink / raw)
To: Jeff Kirsher
Cc: intel-wired-lan, Linux Kernel Mailing List, Mario Limonciello
[-- Attachment #1.1: Type: text/plain, Size: 1730 bytes --]
Dear Linux folks,
Trying to decrease the resume time of Linux 5.3-rc3 on the Dell OptiPlex
5040 with the device below
$ lspci -nn -s 00:1f.6
00:1f.6 Ethernet controller [0200]: Intel Corporation Ethernet Connection (2) I219-V [8086:15b8] (rev 31)
pm-graph’s script `sleepgraph.py` shows, that the driver *e1000e* takes
around 400 ms, which is quite a lot. The call graph trace shows that
`e1000e_read_phy_reg_mdic()` is responsible for a lot of those. From
`drivers/net/ethernet/intel/e1000e/phy.c` [1]:
for (i = 0; i < (E1000_GEN_POLL_TIMEOUT * 3); i++) {
udelay(50);
mdic = er32(MDIC);
if (mdic & E1000_MDIC_READY)
break;
}
if (!(mdic & E1000_MDIC_READY)) {
e_dbg("MDI Read did not complete\n");
return -E1000_ERR_PHY;
}
if (mdic & E1000_MDIC_ERROR) {
e_dbg("MDI Error\n");
return -E1000_ERR_PHY;
}
Unfortunately, errors are not logged if dynamic debug is disabled,
so rebuilding the Linux kernel with `CONFIG_DYNAMIC_DEBUG`, and
echo "file drivers/net/ethernet/* +p" | sudo tee /sys/kernel/debug/dynamic_debug/control
I got the messages below.
[ 4159.204192] e1000e 0000:00:1f.6 net00: MDI Error
[ 4160.267950] e1000e 0000:00:1f.6 net00: MDI Write did not complete
[ 4160.359855] e1000e 0000:00:1f.6 net00: MDI Error
Can you please shed a little more light into these errors? Please
find the full log attached.
Kind regards,
Paul
[1]: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/drivers/net/ethernet/intel/e1000e/phy.c#n206
[-- Attachment #1.2: linux-5.3-rc3-e1000e.txt --]
[-- Type: text/plain, Size: 92857 bytes --]
[ 0.607722] system 00:08: [mem 0xfed19000-0xfed19fff] has been reserved
[ 0.608268] system 00:08: [mem 0xf8000000-0xfbffffff] has been reserved
[ 0.608813] system 00:08: [mem 0xfed20000-0xfed3ffff] has been reserved
[ 0.609359] system 00:08: [mem 0xfed90000-0xfed93fff] has been reserved
[ 0.609905] system 00:08: [mem 0xfed45000-0xfed8ffff] has been reserved
[ 0.610450] system 00:08: [mem 0xff000000-0xffffffff] has been reserved
[ 0.610994] system 00:08: [mem 0xfee00000-0xfeefffff] could not be reserved
[ 0.611567] system 00:08: [mem 0xf7fe0000-0xf7ffffff] has been reserved
[ 0.612113] system 00:08: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.612138] system 00:09: [mem 0xfd000000-0xfdabffff] has been reserved
[ 0.612682] system 00:09: [mem 0xfdad0000-0xfdadffff] has been reserved
[ 0.613228] system 00:09: [mem 0xfdb00000-0xfdffffff] has been reserved
[ 0.613773] system 00:09: [mem 0xfe000000-0xfe01ffff] could not be reserved
[ 0.614347] system 00:09: [mem 0xfe036000-0xfe03bfff] has been reserved
[ 0.614892] system 00:09: [mem 0xfe03d000-0xfe3fffff] has been reserved
[ 0.615437] system 00:09: [mem 0xfe410000-0xfe7fffff] has been reserved
[ 0.615984] system 00:09: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.616165] system 00:0a: [io 0xff00-0xfffe] has been reserved
[ 0.616656] system 00:0a: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.617377] system 00:0b: [mem 0xfdaf0000-0xfdafffff] has been reserved
[ 0.617924] system 00:0b: [mem 0xfdae0000-0xfdaeffff] has been reserved
[ 0.618468] system 00:0b: [mem 0xfdac0000-0xfdacffff] has been reserved
[ 0.619015] system 00:0b: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.619567] pnp: PnP ACPI: found 12 devices
[ 0.620626] thermal_sys: Registered thermal governor 'step_wise'
[ 0.620627] thermal_sys: Registered thermal governor 'user_space'
[ 0.625646] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns
[ 0.626880] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 0.627293] pci 0000:00:01.0: bridge window [io 0xe000-0xefff]
[ 0.627796] pci 0000:00:01.0: bridge window [mem 0xf7e00000-0xf7efffff]
[ 0.628356] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xefffffff 64bit pref]
[ 0.628995] pci 0000:02:00.0: PCI bridge to [bus 03]
[ 0.629420] pci 0000:00:1c.0: PCI bridge to [bus 02-03]
[ 0.629859] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7 window]
[ 0.630368] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff window]
[ 0.630879] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window]
[ 0.631444] pci_bus 0000:00: resource 7 [mem 0xe0000000-0xf7ffffff window]
[ 0.632010] pci_bus 0000:00: resource 8 [mem 0xfd000000-0xfe7fffff window]
[ 0.632576] pci_bus 0000:01: resource 0 [io 0xe000-0xefff]
[ 0.633037] pci_bus 0000:01: resource 1 [mem 0xf7e00000-0xf7efffff]
[ 0.633554] pci_bus 0000:01: resource 2 [mem 0xe0000000-0xefffffff 64bit pref]
[ 0.634241] NET: Registered protocol family 2
[ 0.634681] tcp_listen_portaddr_hash hash table entries: 4096 (order: 4, 65536 bytes, linear)
[ 0.635406] TCP established hash table entries: 65536 (order: 7, 524288 bytes, linear)
[ 0.636144] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes, linear)
[ 0.636922] TCP: Hash tables configured (established 65536 bind 65536)
[ 0.637477] UDP hash table entries: 4096 (order: 5, 131072 bytes, linear)
[ 0.638058] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes, linear)
[ 0.639376] pci 0000:01:00.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff]
[ 0.640089] pci 0000:01:00.1: D0 power state depends on 0000:01:00.0
[ 0.640617] PCI: CLS 0 bytes, default 64
[ 0.640980] Trying to unpack rootfs image as initramfs...
[ 0.698966] Freeing initrd memory: 5136K
[ 0.699300] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 0.699832] software IO TLB: mapped [mem 0xd2a46000-0xd6a46000] (64MB)
[ 0.700453] RAPL PMU: API unit is 2^-32 Joules, 3 fixed counters, 655360 ms ovfl timer
[ 0.701105] RAPL PMU: hw unit of domain pp0-core 2^-14 Joules
[ 0.701579] RAPL PMU: hw unit of domain package 2^-14 Joules
[ 0.702048] RAPL PMU: hw unit of domain dram 2^-14 Joules
[ 0.702886] workingset: timestamp_bits=40 max_order=21 bucket_order=0
[ 0.703515] SGI XFS with ACLs, security attributes, realtime, no debug enabled
[ 0.704226] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[ 0.704851] io scheduler mq-deadline registered
[ 0.705228] io scheduler kyber registered
[ 0.705854] efifb: probing for efifb
[ 0.706161] efifb: framebuffer at 0xe0000000, using 3072k, total 3072k
[ 0.706698] efifb: mode is 1024x768x32, linelength=4096, pages=1
[ 0.707194] efifb: scrolling: redraw
[ 0.707494] efifb: Truecolor: size=8:8:8:8, shift=24:16:8:0
[ 0.708970] Console: switching to colour frame buffer device 128x48
[ 0.710450] fb0: EFI VGA frame buffer device
[ 0.710817] IPMI message handler: version 39.2
[ 0.711199] ipmi device interface
[ 0.711488] ipmi_si: IPMI System Interface driver
[ 0.711907] ipmi_si: Unable to find any System Interface(s)
[ 0.712379] IPMI Watchdog: driver initialized
[ 0.712750] IPMI poweroff: Copyright (C) 2004 MontaVista Software - IPMI Powerdown via sys_reboot
[ 0.713551] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input0
[ 0.714256] ACPI: Sleep Button [SLPB]
[ 0.714588] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1
[ 0.715291] ACPI: Power Button [PWRB]
[ 0.715624] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[ 0.716252] ACPI: Power Button [PWRF]
[ 0.746206] Monitor-Mwait will be used to enter C-1 state
[ 0.746210] Monitor-Mwait will be used to enter C-2 state
[ 0.746213] Monitor-Mwait will be used to enter C-3 state
[ 0.777203] thermal LNXTHERM:00: registered as thermal_zone0
[ 0.777688] ACPI: Thermal Zone [TZ00] (28 C)
[ 0.778172] thermal LNXTHERM:01: registered as thermal_zone1
[ 0.778653] ACPI: Thermal Zone [TZ01] (30 C)
[ 0.779168] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 0.800445] 00:01: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
[ 0.801827] lp: driver loaded but no devices found
[ 0.802434] Linux agpgart interface v0.103
[ 0.805494] brd: module loaded
[ 0.807073] loop: module loaded
[ 0.812653] drbd: initialized. Version: 8.4.11 (api:1/proto:86-101)
[ 0.813672] drbd: built-in
[ 0.814400] drbd: registered as block device major 147
[ 0.815306] Uniform Multi-Platform E-IDE driver
[ 0.816611] ide_generic: please use "probe_mask=0x3f" module parameter for probing all legacy ISA IDE ports
[ 0.817928] legacy IDE will be removed in 2021, please switch to libata
Report any missing HW support to linux-ide@vger.kernel.org
[ 0.819932] Probing IDE interface ide0...
[ 1.343108] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 1.343996] legacy IDE will be removed in 2021, please switch to libata
Report any missing HW support to linux-ide@vger.kernel.org
[ 1.346075] Probing IDE interface ide1...
[ 1.722068] tsc: Refined TSC clocksource calibration: 3312.001 MHz
[ 1.723099] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x2fbd9516ca9, max_idle_ns: 440795225028 ns
[ 1.724491] clocksource: Switched to clocksource tsc
[ 1.869107] ide1 at 0x170-0x177,0x376 on irq 15
[ 1.870005] ide-gd driver 1.18
[ 1.870767] ide-cd driver 5.00
[ 1.871654] megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03 EST 2006)
[ 1.872841] megaraid: 2.20.5.1 (Release Date: Thu Nov 16 15:32:35 EST 2006)
[ 1.873926] megasas: 07.710.50.00-rc1
[ 1.874761] mpt3sas version 29.100.00.00 loaded
[ 1.876365] ahci 0000:00:17.0: version 3.0
[ 1.886754] ahci 0000:00:17.0: AHCI 0001.0301 32 slots 4 ports 6 Gbps 0xf impl SATA mode
[ 1.887902] ahci 0000:00:17.0: flags: 64bit ncq sntf pm led clo only pio slum part ems deso sadm sds apst
[ 1.898618] scsi host0: ahci
[ 1.899658] scsi host1: ahci
[ 1.900763] scsi host2: ahci
[ 1.901781] scsi host3: ahci
[ 1.902559] ata1: SATA max UDMA/133 abar m2048@0xf7f4b000 port 0xf7f4b100 irq 122
[ 1.903684] ata2: SATA max UDMA/133 abar m2048@0xf7f4b000 port 0xf7f4b180 irq 122
[ 1.904805] ata3: SATA max UDMA/133 abar m2048@0xf7f4b000 port 0xf7f4b200 irq 122
[ 1.905921] ata4: SATA max UDMA/133 abar m2048@0xf7f4b000 port 0xf7f4b280 irq 122
[ 1.907208] tun: Universal TUN/TAP device driver, 1.6
[ 1.908260] bnx2x: QLogic 5771x/578xx 10/20-Gigabit Ethernet Driver bnx2x 1.713.36-0 (2014/02/10)
[ 1.909740] e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI
[ 1.910738] e100: Copyright(c) 1999-2006 Intel Corporation
[ 1.911683] e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k8-NAPI
[ 1.912746] e1000: Copyright (c) 1999-2006 Intel Corporation.
[ 1.913716] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
[ 1.914673] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[ 1.915757] e1000e 0000:00:1f.6: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode
[ 2.216986] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 2.218004] ata3: SATA link down (SStatus 4 SControl 300)
[ 2.218953] ata4: SATA link down (SStatus 4 SControl 300)
[ 2.219894] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 2.220896] ata2.00: ATAPI: HL-DT-ST DVD+/-RW GU90N, A1C0, max UDMA/100
[ 2.226145] ata2.00: configured for UDMA/100
[ 2.250102] ata1.00: ATA-8: ST3250310NS, SN06, max UDMA/133
[ 2.251061] ata1.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 32)
[ 2.294556] ata1.00: configured for UDMA/133
[ 2.295572] scsi 0:0:0:0: Direct-Access ATA ST3250310NS SN06 PQ: 0 ANSI: 5
[ 2.296867] e1000e 0000:00:1f.6 0000:00:1f.6 (uninitialized): registered PHC clock
[ 2.296875] sd 0:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/233 GiB)
[ 2.296888] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 2.298652] scsi 1:0:0:0: CD-ROM HL-DT-ST DVD+-RW GU90N A1C0 PQ: 0 ANSI: 5
[ 2.299100] sd 0:0:0:0: [sda] Write Protect is off
[ 2.302056] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 2.302062] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.319398] sda: sda1 sda2 sda3
[ 2.320688] sd 0:0:0:0: [sda] Attached SCSI disk
[ 2.346628] sr 1:0:0:0: [sr0] scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[ 2.347835] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 2.349001] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 2.349123] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 2.362252] e1000e 0000:00:1f.6 eth0: (PCI Express:2.5GT/s:Width x1) 64:00:6a:2c:10:c1
[ 2.363397] e1000e 0000:00:1f.6 eth0: Intel(R) PRO/1000 Network Connection
[ 2.364531] e1000e 0000:00:1f.6 eth0: MAC: 12, PHY: 12, PBA No: FFFFFF-0FF
[ 2.365604] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.6.0-k
[ 2.366669] igb: Copyright (c) 2007-2014 Intel Corporation.
[ 2.367630] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k
[ 2.368768] igbvf: Copyright (c) 2009 - 2012 Intel Corporation.
[ 2.369776] sky2: driver version 1.30
[ 2.370636] Fusion MPT base driver 3.04.20
[ 2.371445] Copyright (c) 1999-2008 LSI Corporation
[ 2.372309] Fusion MPT SPI Host driver 3.04.20
[ 2.373146] Fusion MPT FC Host driver 3.04.20
[ 2.373979] Fusion MPT SAS Host driver 3.04.20
[ 2.374801] Fusion MPT misc device (ioctl) driver 3.04.20
[ 2.375791] mptctl: Registered with Fusion MPT base driver
[ 2.376724] mptctl: /dev/mptctl @ (major,minor=10,220)
[ 2.377619] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.378639] ehci-pci: EHCI PCI platform driver
[ 2.379489] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 2.380458] ohci-pci: OHCI PCI platform driver
[ 2.381297] uhci_hcd: USB Universal Host Controller Interface driver
[ 2.382401] xhci_hcd 0000:00:14.0: xHCI Host Controller
[ 2.383297] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 1
[ 2.385416] xhci_hcd 0000:00:14.0: hcc params 0x200077c1 hci version 0x100 quirks 0x0000000001109810
[ 2.386632] xhci_hcd 0000:00:14.0: cache line size of 64 is not supported
[ 2.387969] hub 1-0:1.0: USB hub found
[ 2.388714] hub 1-0:1.0: 16 ports detected
[ 2.390316] xhci_hcd 0000:00:14.0: xHCI Host Controller
[ 2.391211] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 2
[ 2.392278] xhci_hcd 0000:00:14.0: Host supports USB 3.0 SuperSpeed
[ 2.393428] hub 2-0:1.0: USB hub found
[ 2.394210] hub 2-0:1.0: 10 ports detected
[ 2.395391] usb: port power management may be unreliable
[ 2.396526] usbcore: registered new interface driver usb-storage
[ 2.397491] usbcore: registered new interface driver ftdi_sio
[ 2.398422] usbserial: USB Serial support registered for FTDI USB Serial Device
[ 2.399479] usbcore: registered new interface driver omninet
[ 2.400397] usbserial: USB Serial support registered for ZyXEL - omni.net lcd plus usb
[ 2.401511] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
[ 2.405499] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 2.406384] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 2.407687] rtc_cmos 00:06: RTC can wake from S4
[ 2.409062] rtc_cmos 00:06: registered as rtc0
[ 2.409835] rtc_cmos 00:06: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
[ 2.411045] i801_smbus 0000:00:1f.4: SPD Write Disable is set
[ 2.411981] i801_smbus 0000:00:1f.4: SMBus using PCI interrupt
[ 2.416233] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.11
[ 2.417222] iTCO_wdt: Found a Intel PCH TCO device (Version=4, TCOBASE=0x0400)
[ 2.418540] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 2.419490] iTCO_vendor_support: vendor-support=0
[ 2.420310] nv_tco: NV TCO WatchDog Timer Driver v0.01
[ 2.421429] intel_pstate: Intel P-state driver initializing
[ 2.423437] intel_pstate: HWP enabled
[ 2.424172] EFI Variables Facility v0.08 2004-May-17
[ 2.432301] hidraw: raw HID events driver (C) Jiri Kosina
[ 2.433266] usbcore: registered new interface driver usbhid
[ 2.434144] usbhid: USB HID core driver
[ 2.434941] Key type dns_resolver registered
[ 2.436323] microcode: sig=0x506e3, pf=0x2, revision=0xc6
[ 2.437263] microcode: Microcode Update Driver: v2.2.
[ 2.437282] sched_clock: Marking stable (2363094852, 73741740)->(2453500722, -16664130)
[ 2.439702] registered taskstats version 1
[ 2.441147] rtc_cmos 00:06: setting system clock to 2019-08-06T13:50:01 UTC (1565099401)
[ 2.442838] Freeing unused kernel image memory: 1612K
[ 2.446082] Write protecting the kernel read-only data: 20480k
[ 2.447468] Freeing unused kernel image memory: 2012K
[ 2.448518] Freeing unused kernel image memory: 704K
[ 2.449406] Run /init as init process
[ 2.693542] random: fast init done
[ 2.716082] usb 1-6: new low-speed USB device number 2 using xhci_hcd
[ 2.796931] XFS (sda1): Mounting V5 Filesystem
[ 2.857612] input: Fujitsu Fujitsu Keyboard as /devices/pci0000:00/0000:00:14.0/usb1/1-6/1-6:1.0/0003:0BF8:101E.0001/input/input6
[ 2.911351] hid-generic 0003:0BF8:101E.0001: input,hidraw0: USB HID v1.10 Keyboard [Fujitsu Fujitsu Keyboard] on usb-0000:00:14.0-6/input0
[ 2.920393] input: Fujitsu Fujitsu Keyboard System Control as /devices/pci0000:00/0000:00:14.0/usb1/1-6/1-6:1.1/0003:0BF8:101E.0002/input/input7
[ 2.939336] XFS (sda1): Ending clean mount
[ 2.974260] input: Fujitsu Fujitsu Keyboard Consumer Control as /devices/pci0000:00/0000:00:14.0/usb1/1-6/1-6:1.1/0003:0BF8:101E.0002/input/input8
[ 2.976569] hid-generic 0003:0BF8:101E.0002: input,hidraw1: USB HID v1.10 Device [Fujitsu Fujitsu Keyboard] on usb-0000:00:14.0-6/input1
[ 3.093082] usb 1-8: new low-speed USB device number 3 using xhci_hcd
[ 3.227668] input: Logitech USB Optical Mouse as /devices/pci0000:00/0000:00:14.0/usb1/1-8/1-8:1.0/0003:046D:C077.0003/input/input9
[ 3.229978] hid-generic 0003:046D:C077.0003: input,hidraw2: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-0000:00:14.0-8/input0
[ 3.346088] usb 1-10: new high-speed USB device number 4 using xhci_hcd
[ 3.446058] random: crng init done
[ 3.480425] usb-storage 1-10:1.0: USB Mass Storage device detected
[ 3.481808] scsi host4: usb-storage 1-10:1.0
[ 4.129869] systemd[1]: Inserted module 'autofs4'
[ 4.388065] NET: Registered protocol family 10
[ 4.389317] Segment Routing with IPv6
[ 4.430772] NET: Registered protocol family 1
[ 4.431792] systemd[1]: Inserted module 'unix'
[ 4.540776] scsi 4:0:0:0: Direct-Access Linux File-CD Gadget 0000 PQ: 0 ANSI: 2
[ 4.542441] sd 4:0:0:0: Attached scsi generic sg2 type 0
[ 4.542715] sd 4:0:0:0: Power-on or device reset occurred
[ 4.547092] sd 4:0:0:0: [sdb] Attached SCSI removable disk
[ 4.759782] systemd[1]: systemd 242 running in system mode. (+PAM -AUDIT -SELINUX +IMA -APPARMOR +SMACK +SYSVINIT +UTMP -LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 -SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid)
[ 4.775184] systemd[1]: Detected architecture x86-64.
[ 4.811196] systemd[1]: Set hostname to <rabammel.molgen.mpg.de>.
[ 5.532829] systemd[1]: Created slice User and Session Slice.
[ 5.534840] systemd[1]: Created slice system-getty.slice.
[ 5.536701] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[ 5.541224] systemd[1]: Listening on Process Core Dump Socket.
[ 5.543098] systemd[1]: Listening on Journal Socket.
[ 5.545245] systemd[1]: Mounting Kernel Debug File System...
[ 5.547407] systemd[1]: Mounting POSIX Message Queue File System...
[ 6.148228] RPC: Registered named UNIX socket transport module.
[ 6.149172] RPC: Registered udp transport module.
[ 6.150010] RPC: Registered tcp transport module.
[ 6.150840] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 6.620888] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 7.032390] systemd-journald[156]: Received request to flush runtime journal from PID 1
[ 7.715845] wmi_bus wmi_bus-PNP0C14:00: WQBC data block query control method not found
[ 9.023944] snd_hda_intel 0000:01:00.1: Handle vga_switcheroo audio client
[ 9.024965] snd_hda_intel 0000:01:00.1: Force to non-snoop mode
[ 9.166877] input: HDA ATI HDMI HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input10
[ 9.168459] input: HDA ATI HDMI HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:01.0/0000:01:00.1/sound/card1/input11
[ 9.217600] snd_hda_codec_realtek hdaudioC0D0: autoconfig for ALC3234: line_outs=1 (0x1b/0x0/0x0/0x0/0x0) type:line
[ 9.218975] snd_hda_codec_realtek hdaudioC0D0: speaker_outs=1 (0x14/0x0/0x0/0x0/0x0)
[ 9.220078] snd_hda_codec_realtek hdaudioC0D0: hp_outs=1 (0x21/0x0/0x0/0x0/0x0)
[ 9.221144] snd_hda_codec_realtek hdaudioC0D0: mono: mono_out=0x0
[ 9.222108] snd_hda_codec_realtek hdaudioC0D0: inputs:
[ 9.222995] snd_hda_codec_realtek hdaudioC0D0: Headphone Mic=0x1a
[ 9.223973] snd_hda_codec_realtek hdaudioC0D0: Headset Mic=0x19
[ 9.465235] input: HDA Intel PCH Headphone Mic as /devices/pci0000:00/0000:00:1f.3/sound/card0/input12
[ 9.466646] input: HDA Intel PCH Line Out as /devices/pci0000:00/0000:00:1f.3/sound/card0/input13
[ 12.387217] [drm] amdgpu kernel modesetting enabled.
[ 12.388127] amdgpu 0000:01:00.0: remove_conflicting_pci_framebuffers: bar 0: 0xe0000000 -> 0xefffffff
[ 12.389338] amdgpu 0000:01:00.0: remove_conflicting_pci_framebuffers: bar 2: 0xf7e00000 -> 0xf7e3ffff
[ 12.390578] checking generic (e0000000 300000) vs hw (e0000000 10000000)
[ 12.390579] fb0: switching to amdgpudrmfb from EFI VGA
[ 12.391637] Console: switching to colour dummy device 80x25
[ 12.392222] amdgpu 0000:01:00.0: vgaarb: deactivate vga console
[ 12.393163] [drm] initializing kernel modesetting (OLAND 0x1002:0x6610 0x1028:0x0081 0x81).
[ 12.393870] [drm] register mmio base: 0xF7E00000
[ 12.394297] [drm] register mmio size: 262144
[ 12.394667] [drm] add ip block number 0 <si_common>
[ 12.395110] [drm] add ip block number 1 <gmc_v6_0>
[ 12.395506] [drm] add ip block number 2 <si_ih>
[ 12.395912] [drm] add ip block number 3 <gfx_v6_0>
[ 12.396308] [drm] add ip block number 4 <si_dma>
[ 12.396690] [drm] add ip block number 5 <si_dpm>
[ 12.397114] [drm] add ip block number 6 <dce_v6_0>
[ 12.397511] amdgpu 0000:01:00.0: kfd not supported on this ASIC
[ 12.402995] [drm] BIOS signature incorrect 0 0
[ 12.403385] ATOM BIOS: 113-C8720100-101
[ 12.403795] [drm] vm size is 64 GB, 2 levels, block size is 10-bit, fragment size is 9-bit
[ 12.464667] amdgpu 0000:01:00.0: VRAM: 4096M 0x000000F400000000 - 0x000000F4FFFFFFFF (4096M used)
[ 12.465439] amdgpu 0000:01:00.0: GART: 1024M 0x000000FF00000000 - 0x000000FF3FFFFFFF
[ 12.466124] [drm] Detected VRAM RAM=4096M, BAR=256M
[ 12.466562] [drm] RAM width 128bits DDR3
[ 12.467136] [TTM] Zone kernel: Available graphics memory: 3907240 KiB
[ 12.467698] [TTM] Zone dma32: Available graphics memory: 2097152 KiB
[ 12.468277] [TTM] Initializing pool allocator
[ 12.468686] [TTM] Initializing DMA pool allocator
[ 12.469756] [drm] amdgpu: 4096M of VRAM memory ready
[ 12.470204] [drm] amdgpu: 4096M of GTT memory ready.
[ 12.470660] [drm] GART: num cpu pages 262144, num gpu pages 262144
[ 12.471747] amdgpu 0000:01:00.0: PCIE GART of 1024M enabled (table at 0x000000F400300000).
[ 12.472511] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 12.473118] [drm] Driver supports precise vblank timestamp query.
[ 12.574730] [drm] Internal thermal controller with fan control
[ 12.575252] [drm] amdgpu: dpm initialized
[ 12.575697] [drm] AMDGPU Display Connectors
[ 12.576093] [drm] Connector 0:
[ 12.576397] [drm] DP-1
[ 12.576613] [drm] HPD1
[ 12.576829] [drm] DDC: 0x194c 0x194c 0x194d 0x194d 0x194e 0x194e 0x194f 0x194f
[ 12.577496] [drm] Encoders:
[ 12.577769] [drm] DFP1: INTERNAL_UNIPHY
[ 12.578156] [drm] Connector 1:
[ 12.578459] [drm] DVI-I-1
[ 12.578695] [drm] HPD2
[ 12.578949] [drm] DDC: 0x1950 0x1950 0x1951 0x1951 0x1952 0x1952 0x1953 0x1953
[ 12.579579] [drm] Encoders:
[ 12.579829] [drm] DFP2: INTERNAL_UNIPHY
[ 12.580219] [drm] CRT1: INTERNAL_KLDSCP_DAC1
[ 12.580789] [drm] PCIE gen 3 link speeds already enabled
[ 12.829086] [drm] fb mappable at 0xE0503000
[ 12.829447] [drm] vram apper at 0xE0000000
[ 12.829788] [drm] size 33177600
[ 12.830110] [drm] fb depth is 24
[ 12.830416] [drm] pitch is 15360
[ 12.830826] fbcon: amdgpudrmfb (fb0) is primary device
[ 12.901400] [drm:dce_v6_0_encoder_mode_set [amdgpu]] *ERROR* Couldn't read SADs: 0
[ 12.944263] Console: switching to colour frame buffer device 240x67
[ 12.978956] amdgpu 0000:01:00.0: fb0: amdgpudrmfb frame buffer device
[ 13.268433] [drm] Initialized amdgpu 3.33.0 20150101 for 0000:01:00.0 on minor 0
[ 16.799048] e1000e 0000:00:1f.6 net00: renamed from eth0
[ 17.329151] 8021q: 802.1Q VLAN Support v1.8
[ 19.212051] XFS (sda2): Mounting V5 Filesystem
[ 19.746689] NFSD: Using UMH upcall client tracking operations.
[ 19.746691] NFSD: starting 90-second grace period (net f0000098)
[ 19.767399] XFS (sda2): Ending clean mount
[ 22.471346] [drm:dce_v6_0_encoder_mode_set [amdgpu]] *ERROR* Couldn't read SADs: 0
[ 23.052343] e1000e: net00 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None
[ 35.763916] FS-Cache: Netfs 'nfs' registered for caching
[ 35.971028] NFS: Registering the id_resolver key type
[ 35.971033] Key type id_resolver registered
[ 35.971034] Key type id_legacy registered
[ 38.491718] fuse: init (API version 7.31)
[ 121.385739] PM: suspend entry (deep)
[ 121.440822] Filesystems sync: 0.055 seconds
[ 121.441014] Freezing user space processes ... (elapsed 0.001 seconds) done.
[ 121.442470] OOM killer disabled.
[ 121.442474] Freezing remaining freezable tasks ... (elapsed 0.000 seconds) done.
[ 121.443499] printk: Suspending console(s) (use no_console_suspend to debug)
[ 121.479948] serial 00:01: disabled
[ 121.481092] e1000e: EEE TX LPI TIMER: 00000011
[ 121.488476] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[ 121.488908] sd 0:0:0:0: [sda] Stopping disk
[ 122.089532] ACPI: Preparing to enter system sleep state S3
[ 122.089892] PM: Saving platform NVS memory
[ 122.089912] Disabling non-boot CPUs ...
[ 122.091114] smpboot: CPU 1 is now offline
[ 122.092681] smpboot: CPU 2 is now offline
[ 122.094239] smpboot: CPU 3 is now offline
[ 122.096153] ACPI: Low-level resume complete
[ 122.096207] PM: Restoring platform NVS memory
[ 122.096837] Enabling non-boot CPUs ...
[ 122.097010] x86: Booting SMP configuration:
[ 122.097010] smpboot: Booting Node 0 Processor 1 APIC 0x2
[ 122.097603] CPU1 is up
[ 122.097756] smpboot: Booting Node 0 Processor 2 APIC 0x4
[ 122.098454] CPU2 is up
[ 122.098620] smpboot: Booting Node 0 Processor 3 APIC 0x6
[ 122.099247] CPU3 is up
[ 122.099858] ACPI: Waking up from system sleep state S3
[ 122.230695] hpet: Lost 3662 RTC interrupts
[ 122.262200] ACPI BIOS Error (bug): AE_AML_BUFFER_LIMIT, Field [DRQL] at bit offset/length 136/8 exceeds size of target Buffer (128 bits) (20190703/dsopcode-203)
[ 122.262203] ACPI Error: Aborting method \_SB.PCI0.LPCB.SIO1.DSRS due to previous error (AE_AML_BUFFER_LIMIT) (20190703/psparse-531)
[ 122.262206] ACPI Error: Aborting method \_SB.PCI0.LPCB.UAR1._SRS due to previous error (AE_AML_BUFFER_LIMIT) (20190703/psparse-531)
[ 122.262209] serial 00:01: activation failed
[ 122.262212] PM: dpm_run_callback(): pnp_bus_resume+0x0/0x90 returns -5
[ 122.262213] PM: Device 00:01 failed to resume: error -5
[ 122.264670] [drm] PCIE gen 3 link speeds already enabled
[ 122.266042] amdgpu 0000:01:00.0: PCIE GART of 1024M enabled (table at 0x000000F400000000).
[ 122.297255] sd 0:0:0:0: [sda] Starting disk
[ 122.608968] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 122.609008] ata4: SATA link down (SStatus 4 SControl 300)
[ 122.609028] ata3: SATA link down (SStatus 4 SControl 300)
[ 122.612979] ata2.00: configured for UDMA/100
[ 122.731498] [drm:dce_v6_0_encoder_mode_set [amdgpu]] *ERROR* Couldn't read SADs: 0
[ 124.425920] usb 1-10: reset high-speed USB device number 4 using xhci_hcd
[ 124.557893] acpi LNXPOWER:16: Turning OFF
[ 124.557930] acpi LNXPOWER:15: Turning OFF
[ 124.557966] acpi LNXPOWER:14: Turning OFF
[ 124.558001] acpi LNXPOWER:13: Turning OFF
[ 124.558037] acpi LNXPOWER:12: Turning OFF
[ 124.558072] acpi LNXPOWER:11: Turning OFF
[ 124.558108] acpi LNXPOWER:10: Turning OFF
[ 124.558143] acpi LNXPOWER:0f: Turning OFF
[ 124.558178] acpi LNXPOWER:0e: Turning OFF
[ 124.558213] acpi LNXPOWER:0d: Turning OFF
[ 124.558249] acpi LNXPOWER:0c: Turning OFF
[ 124.558284] acpi LNXPOWER:0b: Turning OFF
[ 124.558319] acpi LNXPOWER:0a: Turning OFF
[ 124.558391] acpi LNXPOWER:09: Turning OFF
[ 124.558452] acpi LNXPOWER:08: Turning OFF
[ 124.558488] acpi LNXPOWER:07: Turning OFF
[ 124.558523] acpi LNXPOWER:06: Turning OFF
[ 124.558558] acpi LNXPOWER:05: Turning OFF
[ 124.558594] acpi LNXPOWER:04: Turning OFF
[ 124.558629] acpi LNXPOWER:03: Turning OFF
[ 124.558660] OOM killer enabled.
[ 124.558660] Restarting tasks ... done.
[ 124.562506] sd 4:0:0:0: Power-on or device reset occurred
[ 124.590495] PM: suspend exit
[ 124.679378] usb 1-10: USB disconnect, device number 4
[ 127.653558] ata1: link is slow to respond, please be patient (ready=0)
[ 127.705561] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 127.781059] ata1.00: configured for UDMA/133
[ 128.046542] usb 1-10: new high-speed USB device number 5 using xhci_hcd
[ 128.179766] usb-storage 1-10:1.0: USB Mass Storage device detected
[ 128.180012] scsi host4: usb-storage 1-10:1.0
[ 129.212390] scsi 4:0:0:0: Direct-Access Linux File-CD Gadget 0000 PQ: 0 ANSI: 2
[ 129.212652] sd 4:0:0:0: Attached scsi generic sg2 type 0
[ 129.213192] sd 4:0:0:0: Power-on or device reset occurred
[ 129.214308] sd 4:0:0:0: [sdb] Attached SCSI removable disk
[ 131.597990] e1000e: net00 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None
[ 4159.049444] PM: suspend entry (deep)
[ 4159.133091] Filesystems sync: 0.083 seconds
[ 4159.133346] Freezing user space processes ... (elapsed 0.001 seconds) done.
[ 4159.135258] OOM killer disabled.
[ 4159.135258] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
[ 4159.136424] printk: Suspending console(s) (use no_console_suspend to debug)
[ 4159.172606] serial 00:01: disabled
[ 4159.173320] e1000e: EEE TX LPI TIMER: 00000011
[ 4159.184641] e1000e 0000:00:1f.6 net00: Setting page 0x6020
[ 4159.184693] e1000e 0000:00:1f.6 net00: reading PHY page 769 (or 0x6020 shifted) reg 0x14
[ 4159.184750] e1000e 0000:00:1f.6 net00: Setting page 0x6020
[ 4159.184802] e1000e 0000:00:1f.6 net00: writing PHY page 769 (or 0x6020 shifted) reg 0x14
[ 4159.184895] e1000e 0000:00:1f.6 net00: Setting page 0x6020
[ 4159.184947] e1000e 0000:00:1f.6 net00: reading PHY page 769 (or 0x6020 shifted) reg 0x17
[ 4159.185003] e1000e 0000:00:1f.6 net00: Setting page 0x6020
[ 4159.185054] e1000e 0000:00:1f.6 net00: writing PHY page 769 (or 0x6020 shifted) reg 0x17
[ 4159.185110] e1000e 0000:00:1f.6 net00: Setting page 0x6020
[ 4159.185162] e1000e 0000:00:1f.6 net00: reading PHY page 769 (or 0x6020 shifted) reg 0x10
[ 4159.185219] e1000e 0000:00:1f.6 net00: Setting page 0x6020
[ 4159.185271] e1000e 0000:00:1f.6 net00: writing PHY page 769 (or 0x6020 shifted) reg 0x10
[ 4159.185327] e1000e 0000:00:1f.6 net00: Setting page 0x6100
[ 4159.185379] e1000e 0000:00:1f.6 net00: reading PHY page 776 (or 0x6100 shifted) reg 0x14
[ 4159.185435] e1000e 0000:00:1f.6 net00: Setting page 0x6100
[ 4159.185486] e1000e 0000:00:1f.6 net00: writing PHY page 776 (or 0x6100 shifted) reg 0x14
[ 4159.185542] e1000e 0000:00:1f.6 net00: Setting page 0x6100
[ 4159.185594] e1000e 0000:00:1f.6 net00: writing PHY page 776 (or 0x6100 shifted) reg 0x17
[ 4159.185650] e1000e 0000:00:1f.6 net00: Setting page 0x6040
[ 4159.185702] e1000e 0000:00:1f.6 net00: reading PHY page 770 (or 0x6040 shifted) reg 0x11
[ 4159.185758] e1000e 0000:00:1f.6 net00: Setting page 0x6040
[ 4159.185810] e1000e 0000:00:1f.6 net00: writing PHY page 770 (or 0x6040 shifted) reg 0x11
[ 4159.185866] e1000e 0000:00:1f.6 net00: Setting page 0x6020
[ 4159.185918] e1000e 0000:00:1f.6 net00: writing PHY page 769 (or 0x6020 shifted) reg 0x14
[ 4159.186002] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x0
[ 4159.186058] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x0
[ 4159.186113] e1000e 0000:00:1f.6 net00: After fix-ups FlowControl is now = 3
[ 4159.186118] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4159.186170] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x16
[ 4159.186239] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4159.186291] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x16
[ 4159.186348] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4159.186399] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x12
[ 4159.186456] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4159.186507] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x12
[ 4159.186564] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x9
[ 4159.186620] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x9
[ 4159.186673] e1000e 0000:00:1f.6 net00: Reconfiguring auto-neg advertisement params
[ 4159.186676] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x4
[ 4159.186732] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x9
[ 4159.186786] e1000e 0000:00:1f.6 net00: autoneg_advertised 2f
[ 4159.186786] e1000e 0000:00:1f.6 net00: Advertise 10mb Half duplex
[ 4159.186787] e1000e 0000:00:1f.6 net00: Advertise 10mb Full duplex
[ 4159.186787] e1000e 0000:00:1f.6 net00: Advertise 100mb Half duplex
[ 4159.186788] e1000e 0000:00:1f.6 net00: Advertise 100mb Full duplex
[ 4159.186788] e1000e 0000:00:1f.6 net00: Advertise 1000mb Full duplex
[ 4159.186792] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x4
[ 4159.186845] e1000e 0000:00:1f.6 net00: Auto-Neg Advertising de1
[ 4159.186848] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x9
[ 4159.186901] e1000e 0000:00:1f.6 net00: Restarting Auto-Neg
[ 4159.186904] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x0
[ 4159.186961] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x0
[ 4159.187017] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4159.187073] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4159.187139] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4159.187213] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4159.187279] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4159.187335] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4159.187402] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4159.187458] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4159.187524] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4159.187580] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4159.187646] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4159.187703] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4159.187769] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4159.187825] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4159.187891] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4159.187947] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4159.188013] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4159.188070] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4159.188136] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4159.188192] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4159.188255] e1000e 0000:00:1f.6 net00: Unable to establish link!!!
[ 4159.188259] e1000e 0000:00:1f.6 net00: Setting page 0x6020
[ 4159.188311] e1000e 0000:00:1f.6 net00: writing PHY page 769 (or 0x6020 shifted) reg 0x1b
[ 4159.188371] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4159.188423] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x10
[ 4159.188474] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4159.188526] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x11
[ 4159.188580] e1000e 0000:00:1f.6 net00: Setting page 0x6020
[ 4159.188734] e1000e 0000:00:1f.6 net00: Setting page 0x6400
[ 4159.188786] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x46
[ 4159.188889] e1000e 0000:00:1f.6 net00: Setting page 0x6020
[ 4159.188992] e1000e 0000:00:1f.6 net00: Setting page 0x6020
[ 4159.189146] e1000e 0000:00:1f.6 net00: Setting page 0x6400
[ 4159.189214] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x46
[ 4159.189317] e1000e 0000:00:1f.6 net00: Setting page 0x6020
[ 4159.189420] e1000e 0000:00:1f.6 net00: Setting page 0x6020
[ 4159.189472] e1000e 0000:00:1f.6 net00: reading PHY page 769 (or 0x6020 shifted) reg 0x1c
[ 4159.189524] e1000e 0000:00:1f.6 net00: Setting page 0x6020
[ 4159.189576] e1000e 0000:00:1f.6 net00: writing PHY page 769 (or 0x6020 shifted) reg 0x1c
[ 4159.189628] e1000e 0000:00:1f.6 net00: Setting page 0x6080
[ 4159.189680] e1000e 0000:00:1f.6 net00: reading PHY page 772 (or 0x6080 shifted) reg 0x1a
[ 4159.189732] e1000e 0000:00:1f.6 net00: Setting page 0x6080
[ 4159.189784] e1000e 0000:00:1f.6 net00: writing PHY page 772 (or 0x6080 shifted) reg 0x1a
[ 4159.189835] e1000e 0000:00:1f.6 net00: Setting page 0x6080
[ 4159.189887] e1000e 0000:00:1f.6 net00: reading PHY page 772 (or 0x6080 shifted) reg 0x1d
[ 4159.189939] e1000e 0000:00:1f.6 net00: Setting page 0x6080
[ 4159.189991] e1000e 0000:00:1f.6 net00: writing PHY page 772 (or 0x6080 shifted) reg 0x1d
[ 4159.190051] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4159.190103] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x19
[ 4159.190156] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4159.190214] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x19
[ 4159.190272] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4159.190324] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1a
[ 4159.190376] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4159.190428] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x1a
[ 4159.190484] e1000e 0000:00:1f.6 net00: Setting page 0x6020
[ 4159.190638] e1000e 0000:00:1f.6 net00: Setting page 0x6400
[ 4159.190692] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x10
[ 4159.190795] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x11
[ 4159.190899] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x12
[ 4159.191003] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x13
[ 4159.191108] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x14
[ 4159.191216] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x15
[ 4159.191320] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x16
[ 4159.191424] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x17
[ 4159.191528] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x18
[ 4159.191632] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x19
[ 4159.191737] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x1a
[ 4159.191840] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x1b
[ 4159.191944] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x1c
[ 4159.192047] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x1d
[ 4159.192152] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x1e
[ 4159.192265] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x1f
[ 4159.192369] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x20
[ 4159.192473] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x21
[ 4159.192577] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x22
[ 4159.192681] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x23
[ 4159.192785] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x24
[ 4159.192889] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x25
[ 4159.192993] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x26
[ 4159.193097] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x27
[ 4159.193218] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x28
[ 4159.193321] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x29
[ 4159.193426] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x2a
[ 4159.193529] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x2b
[ 4159.193634] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x2c
[ 4159.193737] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x2d
[ 4159.193842] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x2e
[ 4159.193945] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x2f
[ 4159.194050] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x30
[ 4159.194153] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x31
[ 4159.194266] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x32
[ 4159.194370] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x33
[ 4159.194474] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x34
[ 4159.194577] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x35
[ 4159.194682] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x36
[ 4159.194786] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x37
[ 4159.194890] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x38
[ 4159.194993] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x39
[ 4159.195099] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x3a
[ 4159.195213] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x3b
[ 4159.195318] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x3c
[ 4159.195422] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x3d
[ 4159.195526] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x3e
[ 4159.195629] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x3f
[ 4159.195732] e1000e 0000:00:1f.6 net00: Setting page 0x6020
[ 4159.195840] e1000e 0000:00:1f.6 net00: Setting page 0x6020
[ 4159.195995] e1000e 0000:00:1f.6 net00: Setting page 0x6400
[ 4159.196048] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x80
[ 4159.196152] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x81
[ 4159.196267] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x82
[ 4159.196370] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x83
[ 4159.196474] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x84
[ 4159.196578] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x85
[ 4159.196682] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x86
[ 4159.196786] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x87
[ 4159.196890] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x88
[ 4159.196994] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x89
[ 4159.197099] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x8a
[ 4159.197213] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x8b
[ 4159.197318] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x8c
[ 4159.197422] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x8d
[ 4159.197527] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x8e
[ 4159.197630] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x8f
[ 4159.197735] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x90
[ 4159.197838] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x91
[ 4159.197943] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x92
[ 4159.198046] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x93
[ 4159.198151] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x94
[ 4159.198262] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x95
[ 4159.198367] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x96
[ 4159.198470] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x97
[ 4159.198574] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x98
[ 4159.198677] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x99
[ 4159.198782] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x9a
[ 4159.198885] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x9b
[ 4159.198989] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x9c
[ 4159.199092] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x9d
[ 4159.199214] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x9e
[ 4159.199317] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x9f
[ 4159.199421] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0xa0
[ 4159.199524] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0xa1
[ 4159.199629] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0xa2
[ 4159.199732] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0xa3
[ 4159.199837] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0xa4
[ 4159.199940] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0xa5
[ 4159.200044] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0xa6
[ 4159.200147] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0xa7
[ 4159.200267] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0xa8
[ 4159.200370] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0xa9
[ 4159.200474] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0xaa
[ 4159.200577] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0xab
[ 4159.200682] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0xac
[ 4159.200785] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0xad
[ 4159.200889] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0xae
[ 4159.200992] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0xaf
[ 4159.201097] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0xb0
[ 4159.201213] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0xb1
[ 4159.201318] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0xb2
[ 4159.201421] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0xb3
[ 4159.201526] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0xb4
[ 4159.201629] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0xb5
[ 4159.201733] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0xb6
[ 4159.201836] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0xb7
[ 4159.201941] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0xb8
[ 4159.202044] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0xb9
[ 4159.202149] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0xba
[ 4159.202264] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0xbb
[ 4159.202369] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0xbc
[ 4159.202472] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0xbd
[ 4159.202577] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0xbe
[ 4159.202680] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0xbf
[ 4159.202783] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x0
[ 4159.202889] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x0
[ 4159.202992] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x2
[ 4159.203095] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x1
[ 4159.203214] e1000e 0000:00:1f.6 net00: Setting page 0x6020
[ 4159.203323] e1000e 0000:00:1f.6 net00: Setting page 0x6020
[ 4159.203375] e1000e 0000:00:1f.6 net00: reading PHY page 769 (or 0x6020 shifted) reg 0x17
[ 4159.203427] e1000e 0000:00:1f.6 net00: Setting page 0x6020
[ 4159.203479] e1000e 0000:00:1f.6 net00: writing PHY page 769 (or 0x6020 shifted) reg 0x17
[ 4159.204192] e1000e 0000:00:1f.6 net00: MDI Error
[ 4159.204194] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4159.204449] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x19
[ 4159.204654] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4159.204858] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x19
[ 4159.205063] e1000e 0000:00:1f.6 net00: Setting page 0x6160
[ 4159.205268] e1000e 0000:00:1f.6 net00: reading PHY page 779 (or 0x6160 shifted) reg 0x10
[ 4159.205474] e1000e 0000:00:1f.6 net00: Setting page 0x6160
[ 4159.205679] e1000e 0000:00:1f.6 net00: writing PHY page 779 (or 0x6160 shifted) reg 0x10
[ 4159.205885] e1000e 0000:00:1f.6 net00: Setting page 0x6160
[ 4159.206089] e1000e 0000:00:1f.6 net00: writing PHY page 779 (or 0x6160 shifted) reg 0x10
[ 4159.214449] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[ 4159.214882] sd 0:0:0:0: [sda] Stopping disk
[ 4159.980530] ACPI: Preparing to enter system sleep state S3
[ 4159.980892] PM: Saving platform NVS memory
[ 4159.980909] Disabling non-boot CPUs ...
[ 4159.982103] smpboot: CPU 1 is now offline
[ 4159.983742] smpboot: CPU 2 is now offline
[ 4159.985250] smpboot: CPU 3 is now offline
[ 4159.987297] ACPI: Low-level resume complete
[ 4159.987353] PM: Restoring platform NVS memory
[ 4159.987993] Enabling non-boot CPUs ...
[ 4159.988174] x86: Booting SMP configuration:
[ 4159.988175] smpboot: Booting Node 0 Processor 1 APIC 0x2
[ 4159.988766] CPU1 is up
[ 4159.988925] smpboot: Booting Node 0 Processor 2 APIC 0x4
[ 4159.989554] CPU2 is up
[ 4159.989722] smpboot: Booting Node 0 Processor 3 APIC 0x6
[ 4159.990357] CPU3 is up
[ 4159.990954] ACPI: Waking up from system sleep state S3
[ 4160.132884] ACPI BIOS Error (bug): AE_AML_BUFFER_LIMIT, Field [DRQL] at bit offset/length 136/8 exceeds size of target Buffer (128 bits) (20190703/dsopcode-203)
[ 4160.132887] ACPI Error: Aborting method \_SB.PCI0.LPCB.SIO1.DSRS due to previous error (AE_AML_BUFFER_LIMIT) (20190703/psparse-531)
[ 4160.132890] ACPI Error: Aborting method \_SB.PCI0.LPCB.UAR1._SRS due to previous error (AE_AML_BUFFER_LIMIT) (20190703/psparse-531)
[ 4160.132893] serial 00:01: activation failed
[ 4160.132896] PM: dpm_run_callback(): pnp_bus_resume+0x0/0x90 returns -5
[ 4160.132897] PM: Device 00:01 failed to resume: error -5
[ 4160.134919] [drm] PCIE gen 3 link speeds already enabled
[ 4160.136292] amdgpu 0000:01:00.0: PCIE GART of 1024M enabled (table at 0x000000F400000000).
[ 4160.143382] sd 0:0:0:0: [sda] Starting disk
[ 4160.169387] e1000e 0000:00:1f.6 net00: Setting page 0x6020
[ 4160.267950] e1000e 0000:00:1f.6 net00: MDI Write did not complete
[ 4160.319407] e1000e 0000:00:1f.6 net00: Setting page 0x6020
[ 4160.319663] e1000e 0000:00:1f.6 net00: reading PHY page 769 (or 0x6020 shifted) reg 0x17
[ 4160.319868] e1000e 0000:00:1f.6 net00: Setting page 0x6020
[ 4160.320072] e1000e 0000:00:1f.6 net00: writing PHY page 769 (or 0x6020 shifted) reg 0x17
[ 4160.359855] e1000e 0000:00:1f.6 net00: MDI Error
[ 4160.359856] e1000e 0000:00:1f.6 net00: Setting page 0x6040
[ 4160.359908] e1000e 0000:00:1f.6 net00: reading PHY page 770 (or 0x6040 shifted) reg 0x11
[ 4160.359960] e1000e 0000:00:1f.6 net00: Setting page 0x6040
[ 4160.360012] e1000e 0000:00:1f.6 net00: writing PHY page 770 (or 0x6040 shifted) reg 0x11
[ 4160.360063] e1000e 0000:00:1f.6 net00: Setting page 0x6160
[ 4160.360115] e1000e 0000:00:1f.6 net00: reading PHY page 779 (or 0x6160 shifted) reg 0x10
[ 4160.360167] e1000e 0000:00:1f.6 net00: Setting page 0x6160
[ 4160.360218] e1000e 0000:00:1f.6 net00: writing PHY page 779 (or 0x6160 shifted) reg 0x10
[ 4160.360270] e1000e 0000:00:1f.6 net00: Setting page 0x6160
[ 4160.360322] e1000e 0000:00:1f.6 net00: writing PHY page 779 (or 0x6160 shifted) reg 0x10
[ 4160.381769] e1000e 0000:00:1f.6 net00: Setting page 0x6020
[ 4160.381821] e1000e 0000:00:1f.6 net00: reading PHY page 769 (or 0x6020 shifted) reg 0x11
[ 4160.381880] e1000e 0000:00:1f.6 net00: Setting page 0x6020
[ 4160.381932] e1000e 0000:00:1f.6 net00: writing PHY page 769 (or 0x6020 shifted) reg 0x11
[ 4160.381994] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4160.382046] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1a
[ 4160.382098] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4160.382149] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x1a
[ 4160.382202] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4160.382254] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x1e
[ 4160.382501] e1000e 0000:00:1f.6 net00: Setting page 0x6080
[ 4160.382553] e1000e 0000:00:1f.6 net00: writing PHY page 772 (or 0x6080 shifted) reg 0x10
[ 4160.382761] e1000e 0000:00:1f.6 net00: Setting page 0x6040
[ 4160.382812] e1000e 0000:00:1f.6 net00: writing PHY page 770 (or 0x6040 shifted) reg 0x11
[ 4160.382941] e1000e 0000:00:1f.6 net00: Setting page 0x6040
[ 4160.382993] e1000e 0000:00:1f.6 net00: writing PHY page 770 (or 0x6040 shifted) reg 0x12
[ 4160.383199] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4160.383250] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x10
[ 4160.383424] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4160.383476] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x11
[ 4160.383604] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4160.383656] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x10
[ 4160.383789] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4160.383841] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x11
[ 4160.383969] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4160.384021] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x10
[ 4160.384150] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4160.384202] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x11
[ 4160.384330] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4160.384395] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x10
[ 4160.384524] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4160.384576] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x11
[ 4160.384704] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4160.384756] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x10
[ 4160.384885] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4160.384937] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x11
[ 4160.385065] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4160.385117] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x10
[ 4160.385246] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4160.385297] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x11
[ 4160.385457] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4160.385508] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x10
[ 4160.385646] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4160.385697] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x11
[ 4160.385826] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4160.385878] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x10
[ 4160.386006] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4160.386058] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x11
[ 4160.386117] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4160.386169] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x19
[ 4160.386222] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4160.386273] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x19
[ 4160.437386] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x2
[ 4160.437438] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x3
[ 4160.437491] e1000e 0000:00:1f.6 net00: Setting page 0x6020
[ 4160.437544] e1000e 0000:00:1f.6 net00: reading PHY page 769 (or 0x6020 shifted) reg 0x17
[ 4160.437596] e1000e 0000:00:1f.6 net00: Setting page 0x6020
[ 4160.437648] e1000e 0000:00:1f.6 net00: writing PHY page 769 (or 0x6020 shifted) reg 0x17
[ 4160.448623] e1000e 0000:00:1f.6 net00: Setting page 0x6080
[ 4160.448676] e1000e 0000:00:1f.6 net00: reading PHY page 772 (or 0x6080 shifted) reg 0x12
[ 4160.448728] e1000e 0000:00:1f.6 net00: Setting page 0x6080
[ 4160.448779] e1000e 0000:00:1f.6 net00: writing PHY page 772 (or 0x6080 shifted) reg 0x12
[ 4160.448833] e1000e 0000:00:1f.6 net00: Setting page 0x6080
[ 4160.448884] e1000e 0000:00:1f.6 net00: reading PHY page 772 (or 0x6080 shifted) reg 0x1a
[ 4160.448936] e1000e 0000:00:1f.6 net00: Setting page 0x6080
[ 4160.448988] e1000e 0000:00:1f.6 net00: writing PHY page 772 (or 0x6080 shifted) reg 0x1a
[ 4160.449039] e1000e 0000:00:1f.6 net00: Setting page 0x6020
[ 4160.449193] e1000e 0000:00:1f.6 net00: Setting page 0x6400
[ 4160.449245] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x46
[ 4160.449348] e1000e 0000:00:1f.6 net00: Setting page 0x6020
[ 4160.449451] e1000e 0000:00:1f.6 net00: Setting page 0x6080
[ 4160.449502] e1000e 0000:00:1f.6 net00: reading PHY page 772 (or 0x6080 shifted) reg 0x1d
[ 4160.449554] e1000e 0000:00:1f.6 net00: Setting page 0x6080
[ 4160.449606] e1000e 0000:00:1f.6 net00: writing PHY page 772 (or 0x6080 shifted) reg 0x1d
[ 4160.449662] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x0
[ 4160.449718] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x0
[ 4160.449772] e1000e 0000:00:1f.6 net00: After fix-ups FlowControl is now = 3
[ 4160.449777] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4160.449829] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x16
[ 4160.449885] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4160.449936] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x16
[ 4160.449992] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4160.450044] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x12
[ 4160.450100] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4160.450152] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x12
[ 4160.450208] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x9
[ 4160.450264] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x9
[ 4160.450317] e1000e 0000:00:1f.6 net00: Reconfiguring auto-neg advertisement params
[ 4160.450320] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x4
[ 4160.450376] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x9
[ 4160.450429] e1000e 0000:00:1f.6 net00: autoneg_advertised 2f
[ 4160.450430] e1000e 0000:00:1f.6 net00: Advertise 10mb Half duplex
[ 4160.450430] e1000e 0000:00:1f.6 net00: Advertise 10mb Full duplex
[ 4160.450431] e1000e 0000:00:1f.6 net00: Advertise 100mb Half duplex
[ 4160.450431] e1000e 0000:00:1f.6 net00: Advertise 100mb Full duplex
[ 4160.450432] e1000e 0000:00:1f.6 net00: Advertise 1000mb Full duplex
[ 4160.450435] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x4
[ 4160.450488] e1000e 0000:00:1f.6 net00: Auto-Neg Advertising de1
[ 4160.450491] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x9
[ 4160.450544] e1000e 0000:00:1f.6 net00: Restarting Auto-Neg
[ 4160.450547] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x0
[ 4160.450603] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x0
[ 4160.450659] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4160.450715] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4160.450781] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4160.450837] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4160.450903] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4160.450959] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4160.451025] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4160.451082] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4160.451148] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4160.451204] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4160.451270] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4160.451326] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4160.451396] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4160.451452] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4160.451518] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4160.451574] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4160.451640] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4160.451696] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4160.451762] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4160.451818] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4160.451881] e1000e 0000:00:1f.6 net00: Unable to establish link!!!
[ 4160.451885] e1000e 0000:00:1f.6 net00: Setting page 0x6020
[ 4160.451937] e1000e 0000:00:1f.6 net00: writing PHY page 769 (or 0x6020 shifted) reg 0x1b
[ 4160.451993] e1000e 0000:00:1f.6 net00: Setting page 0x6020
[ 4160.452147] e1000e 0000:00:1f.6 net00: Setting page 0x6400
[ 4160.452199] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x3
[ 4160.452302] e1000e 0000:00:1f.6 net00: Setting page 0x6020
[ 4160.452424] e1000e 0000:00:1f.6 net00: Setting page 0x6020
[ 4160.452578] e1000e 0000:00:1f.6 net00: Setting page 0x6400
[ 4160.452630] e1000e 0000:00:1f.6 net00: Accessing PHY page 800 reg 0x3
[ 4160.452732] e1000e 0000:00:1f.6 net00: Setting page 0x6020
[ 4160.453065] e1000e 0000:00:1f.6 net00: Masking off all interrupts
[ 4160.457906] ata4: SATA link down (SStatus 4 SControl 300)
[ 4160.457957] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 4160.458026] ata3: SATA link down (SStatus 4 SControl 300)
[ 4160.462005] ata2.00: configured for UDMA/100
[ 4160.463344] e1000e 0000:00:1f.6 net00: Issuing a global reset to ich8lan
[ 4160.506386] e1000e 0000:00:1f.6 net00: Setting page 0x6020
[ 4160.506439] e1000e 0000:00:1f.6 net00: reading PHY page 769 (or 0x6020 shifted) reg 0x11
[ 4160.506503] e1000e 0000:00:1f.6 net00: Setting page 0x6020
[ 4160.506555] e1000e 0000:00:1f.6 net00: writing PHY page 769 (or 0x6020 shifted) reg 0x11
[ 4160.506617] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4160.506668] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1a
[ 4160.506720] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4160.506772] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x1a
[ 4160.506825] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4160.506877] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x1e
[ 4160.507083] e1000e 0000:00:1f.6 net00: Setting page 0x6080
[ 4160.507135] e1000e 0000:00:1f.6 net00: writing PHY page 772 (or 0x6080 shifted) reg 0x10
[ 4160.507343] e1000e 0000:00:1f.6 net00: Setting page 0x6040
[ 4160.507395] e1000e 0000:00:1f.6 net00: writing PHY page 770 (or 0x6040 shifted) reg 0x11
[ 4160.507527] e1000e 0000:00:1f.6 net00: Setting page 0x6040
[ 4160.507578] e1000e 0000:00:1f.6 net00: writing PHY page 770 (or 0x6040 shifted) reg 0x12
[ 4160.507784] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4160.507836] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x10
[ 4160.507965] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4160.508016] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x11
[ 4160.508147] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4160.508199] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x10
[ 4160.508328] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4160.508379] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x11
[ 4160.508521] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4160.508573] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x10
[ 4160.508701] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4160.508753] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x11
[ 4160.508882] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4160.508933] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x10
[ 4160.509062] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4160.509114] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x11
[ 4160.509243] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4160.509294] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x10
[ 4160.509467] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4160.509519] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x11
[ 4160.509647] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4160.509699] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x10
[ 4160.509827] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4160.509879] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x11
[ 4160.510008] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4160.510060] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x10
[ 4160.510189] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4160.510240] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x11
[ 4160.510397] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4160.510449] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x10
[ 4160.510578] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4160.510629] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x11
[ 4160.510688] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4160.510740] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x19
[ 4160.510793] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4160.510845] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x19
[ 4160.510957] e1000e 0000:00:1f.6 net00: Programming MAC Address into RAR[0]
[ 4160.510960] e1000e 0000:00:1f.6 net00: Clearing RAR[1-11]
[ 4160.511091] e1000e 0000:00:1f.6 net00: Zeroing the MTA
[ 4160.511101] e1000e 0000:00:1f.6 net00: After fix-ups FlowControl is now = 3
[ 4160.511106] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4160.511158] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x16
[ 4160.511214] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4160.511265] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x16
[ 4160.511321] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4160.511373] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x12
[ 4160.511429] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4160.511481] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x12
[ 4160.511537] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x9
[ 4160.511593] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x9
[ 4160.511646] e1000e 0000:00:1f.6 net00: Reconfiguring auto-neg advertisement params
[ 4160.511649] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x4
[ 4160.511705] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x9
[ 4160.511758] e1000e 0000:00:1f.6 net00: autoneg_advertised 2f
[ 4160.511759] e1000e 0000:00:1f.6 net00: Advertise 10mb Half duplex
[ 4160.511759] e1000e 0000:00:1f.6 net00: Advertise 10mb Full duplex
[ 4160.511760] e1000e 0000:00:1f.6 net00: Advertise 100mb Half duplex
[ 4160.511760] e1000e 0000:00:1f.6 net00: Advertise 100mb Full duplex
[ 4160.511761] e1000e 0000:00:1f.6 net00: Advertise 1000mb Full duplex
[ 4160.511764] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x4
[ 4160.511817] e1000e 0000:00:1f.6 net00: Auto-Neg Advertising de1
[ 4160.511820] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x9
[ 4160.511873] e1000e 0000:00:1f.6 net00: Restarting Auto-Neg
[ 4160.511876] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x0
[ 4160.511932] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x0
[ 4160.511988] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4160.512045] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4160.512111] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4160.512167] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4160.512233] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4160.512289] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4160.512369] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4160.512425] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4160.512491] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4160.512547] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4160.512613] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4160.512669] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4160.512735] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4160.512791] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4160.512857] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4160.512914] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4160.512980] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4160.513036] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4160.513102] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4160.513158] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4160.513221] e1000e 0000:00:1f.6 net00: Unable to establish link!!!
[ 4160.513225] e1000e 0000:00:1f.6 net00: Setting page 0x6020
[ 4160.513277] e1000e 0000:00:1f.6 net00: writing PHY page 769 (or 0x6020 shifted) reg 0x1b
[ 4160.513445] e1000e 0000:00:1f.6 net00: Setting page 0x6140
[ 4160.513497] e1000e 0000:00:1f.6 net00: reading PHY page 778 (or 0x6140 shifted) reg 0x10
[ 4160.513548] e1000e 0000:00:1f.6 net00: reading PHY page 778 (or 0x6140 shifted) reg 0x11
[ 4160.513600] e1000e 0000:00:1f.6 net00: reading PHY page 778 (or 0x6140 shifted) reg 0x12
[ 4160.513652] e1000e 0000:00:1f.6 net00: reading PHY page 778 (or 0x6140 shifted) reg 0x13
[ 4160.513703] e1000e 0000:00:1f.6 net00: reading PHY page 778 (or 0x6140 shifted) reg 0x14
[ 4160.513755] e1000e 0000:00:1f.6 net00: reading PHY page 778 (or 0x6140 shifted) reg 0x15
[ 4160.513807] e1000e 0000:00:1f.6 net00: reading PHY page 778 (or 0x6140 shifted) reg 0x17
[ 4160.513858] e1000e 0000:00:1f.6 net00: reading PHY page 778 (or 0x6140 shifted) reg 0x18
[ 4160.513910] e1000e 0000:00:1f.6 net00: reading PHY page 778 (or 0x6140 shifted) reg 0x19
[ 4160.513962] e1000e 0000:00:1f.6 net00: reading PHY page 778 (or 0x6140 shifted) reg 0x1a
[ 4160.514014] e1000e 0000:00:1f.6 net00: reading PHY page 778 (or 0x6140 shifted) reg 0x1b
[ 4160.514065] e1000e 0000:00:1f.6 net00: reading PHY page 778 (or 0x6140 shifted) reg 0x1c
[ 4160.514117] e1000e 0000:00:1f.6 net00: reading PHY page 778 (or 0x6140 shifted) reg 0x1d
[ 4160.514169] e1000e 0000:00:1f.6 net00: reading PHY page 778 (or 0x6140 shifted) reg 0x1e
[ 4160.514245] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4160.514297] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x10
[ 4160.514348] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4160.514400] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x11
[ 4160.514456] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4160.514512] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4160.514566] e1000e 0000:00:1f.6 net00: Phy info is only valid if link is up
[ 4160.514669] e1000e 0000:00:1f.6 net00: Setting page 0x6020
[ 4160.514721] e1000e 0000:00:1f.6 net00: reading PHY page 769 (or 0x6020 shifted) reg 0x14
[ 4160.514777] e1000e 0000:00:1f.6 net00: Setting page 0x6020
[ 4160.514828] e1000e 0000:00:1f.6 net00: writing PHY page 769 (or 0x6020 shifted) reg 0x14
[ 4160.514920] e1000e 0000:00:1f.6 net00: Setting page 0x6020
[ 4160.514972] e1000e 0000:00:1f.6 net00: reading PHY page 769 (or 0x6020 shifted) reg 0x17
[ 4160.515028] e1000e 0000:00:1f.6 net00: Setting page 0x6020
[ 4160.515080] e1000e 0000:00:1f.6 net00: writing PHY page 769 (or 0x6020 shifted) reg 0x17
[ 4160.515136] e1000e 0000:00:1f.6 net00: Setting page 0x6020
[ 4160.515188] e1000e 0000:00:1f.6 net00: reading PHY page 769 (or 0x6020 shifted) reg 0x10
[ 4160.515244] e1000e 0000:00:1f.6 net00: Setting page 0x6020
[ 4160.515295] e1000e 0000:00:1f.6 net00: writing PHY page 769 (or 0x6020 shifted) reg 0x10
[ 4160.515369] e1000e 0000:00:1f.6 net00: Setting page 0x6100
[ 4160.515420] e1000e 0000:00:1f.6 net00: reading PHY page 776 (or 0x6100 shifted) reg 0x14
[ 4160.515476] e1000e 0000:00:1f.6 net00: Setting page 0x6100
[ 4160.515528] e1000e 0000:00:1f.6 net00: writing PHY page 776 (or 0x6100 shifted) reg 0x14
[ 4160.515584] e1000e 0000:00:1f.6 net00: Setting page 0x6100
[ 4160.515636] e1000e 0000:00:1f.6 net00: writing PHY page 776 (or 0x6100 shifted) reg 0x17
[ 4160.515692] e1000e 0000:00:1f.6 net00: Setting page 0x6040
[ 4160.515744] e1000e 0000:00:1f.6 net00: reading PHY page 770 (or 0x6040 shifted) reg 0x11
[ 4160.515800] e1000e 0000:00:1f.6 net00: Setting page 0x6040
[ 4160.515852] e1000e 0000:00:1f.6 net00: writing PHY page 770 (or 0x6040 shifted) reg 0x11
[ 4160.515908] e1000e 0000:00:1f.6 net00: Setting page 0x6020
[ 4160.515959] e1000e 0000:00:1f.6 net00: writing PHY page 769 (or 0x6020 shifted) reg 0x14
[ 4160.528399] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4160.528455] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4160.602510] [drm:dce_v6_0_encoder_mode_set [amdgpu]] *ERROR* Couldn't read SADs: 0
[ 4162.395960] usb 1-10: reset high-speed USB device number 5 using xhci_hcd
[ 4162.527711] acpi LNXPOWER:16: Turning OFF
[ 4162.527748] acpi LNXPOWER:15: Turning OFF
[ 4162.527784] acpi LNXPOWER:14: Turning OFF
[ 4162.527820] acpi LNXPOWER:13: Turning OFF
[ 4162.527856] acpi LNXPOWER:12: Turning OFF
[ 4162.527891] acpi LNXPOWER:11: Turning OFF
[ 4162.527927] acpi LNXPOWER:10: Turning OFF
[ 4162.527962] acpi LNXPOWER:0f: Turning OFF
[ 4162.527998] acpi LNXPOWER:0e: Turning OFF
[ 4162.528033] acpi LNXPOWER:0d: Turning OFF
[ 4162.528069] acpi LNXPOWER:0c: Turning OFF
[ 4162.528105] acpi LNXPOWER:0b: Turning OFF
[ 4162.528140] acpi LNXPOWER:0a: Turning OFF
[ 4162.528176] acpi LNXPOWER:09: Turning OFF
[ 4162.528211] acpi LNXPOWER:08: Turning OFF
[ 4162.528247] acpi LNXPOWER:07: Turning OFF
[ 4162.528282] acpi LNXPOWER:06: Turning OFF
[ 4162.528317] acpi LNXPOWER:05: Turning OFF
[ 4162.528390] acpi LNXPOWER:04: Turning OFF
[ 4162.528439] acpi LNXPOWER:03: Turning OFF
[ 4162.528467] OOM killer enabled.
[ 4162.528467] Restarting tasks ... done.
[ 4162.532198] sd 4:0:0:0: Power-on or device reset occurred
[ 4162.533344] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4162.533400] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4162.544542] e1000e 0000:00:1f.6 net00: Masking off all interrupts
[ 4162.555330] e1000e 0000:00:1f.6 net00: Issuing a global reset to ich8lan
[ 4162.560478] PM: suspend exit
[ 4162.599447] e1000e 0000:00:1f.6 net00: Setting page 0x6020
[ 4162.599500] e1000e 0000:00:1f.6 net00: reading PHY page 769 (or 0x6020 shifted) reg 0x11
[ 4162.599556] e1000e 0000:00:1f.6 net00: Setting page 0x6020
[ 4162.599608] e1000e 0000:00:1f.6 net00: writing PHY page 769 (or 0x6020 shifted) reg 0x11
[ 4162.599668] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4162.599720] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1a
[ 4162.599772] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4162.599823] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x1a
[ 4162.599876] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4162.599928] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x1e
[ 4162.600135] e1000e 0000:00:1f.6 net00: Setting page 0x6080
[ 4162.600187] e1000e 0000:00:1f.6 net00: writing PHY page 772 (or 0x6080 shifted) reg 0x10
[ 4162.600457] e1000e 0000:00:1f.6 net00: Setting page 0x6040
[ 4162.600509] e1000e 0000:00:1f.6 net00: writing PHY page 770 (or 0x6040 shifted) reg 0x11
[ 4162.600661] e1000e 0000:00:1f.6 net00: Setting page 0x6040
[ 4162.600713] e1000e 0000:00:1f.6 net00: writing PHY page 770 (or 0x6040 shifted) reg 0x12
[ 4162.600919] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4162.600971] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x10
[ 4162.601098] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4162.601150] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x11
[ 4162.601282] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4162.601334] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x10
[ 4162.601473] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4162.601530] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x11
[ 4162.601661] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4162.601713] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x10
[ 4162.601840] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4162.601892] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x11
[ 4162.602022] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4162.602074] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x10
[ 4162.602211] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4162.602263] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x11
[ 4162.602435] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4162.602487] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x10
[ 4162.602613] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4162.602677] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x11
[ 4162.602833] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4162.602885] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x10
[ 4162.603012] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4162.603068] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x11
[ 4162.603199] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4162.603251] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x10
[ 4162.603416] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4162.603468] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x11
[ 4162.603619] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4162.603671] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x10
[ 4162.603798] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4162.603850] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x11
[ 4162.603908] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4162.603959] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x19
[ 4162.604012] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4162.604064] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x19
[ 4162.604177] e1000e 0000:00:1f.6 net00: Programming MAC Address into RAR[0]
[ 4162.604181] e1000e 0000:00:1f.6 net00: Clearing RAR[1-11]
[ 4162.604298] e1000e 0000:00:1f.6 net00: Zeroing the MTA
[ 4162.604309] e1000e 0000:00:1f.6 net00: After fix-ups FlowControl is now = 3
[ 4162.604314] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4162.604365] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x16
[ 4162.604424] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4162.604475] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x16
[ 4162.604531] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4162.604583] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x12
[ 4162.604639] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4162.604691] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x12
[ 4162.604746] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x9
[ 4162.604802] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x9
[ 4162.604861] e1000e 0000:00:1f.6 net00: Reconfiguring auto-neg advertisement params
[ 4162.604864] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x4
[ 4162.604920] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x9
[ 4162.604973] e1000e 0000:00:1f.6 net00: autoneg_advertised 2f
[ 4162.604973] e1000e 0000:00:1f.6 net00: Advertise 10mb Half duplex
[ 4162.604974] e1000e 0000:00:1f.6 net00: Advertise 10mb Full duplex
[ 4162.604974] e1000e 0000:00:1f.6 net00: Advertise 100mb Half duplex
[ 4162.604975] e1000e 0000:00:1f.6 net00: Advertise 100mb Full duplex
[ 4162.604975] e1000e 0000:00:1f.6 net00: Advertise 1000mb Full duplex
[ 4162.604978] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x4
[ 4162.605031] e1000e 0000:00:1f.6 net00: Auto-Neg Advertising de1
[ 4162.605034] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x9
[ 4162.605087] e1000e 0000:00:1f.6 net00: Restarting Auto-Neg
[ 4162.605090] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x0
[ 4162.605146] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x0
[ 4162.605202] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4162.605258] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4162.605324] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4162.605380] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4162.605472] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4162.605527] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4162.605593] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4162.605649] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4162.605715] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4162.605770] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4162.605836] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4162.605892] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4162.605958] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4162.606014] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4162.606079] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4162.606135] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4162.606201] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4162.606257] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4162.606323] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4162.606379] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4162.606461] e1000e 0000:00:1f.6 net00: Unable to establish link!!!
[ 4162.606465] e1000e 0000:00:1f.6 net00: Setting page 0x6020
[ 4162.606516] e1000e 0000:00:1f.6 net00: writing PHY page 769 (or 0x6020 shifted) reg 0x1b
[ 4162.606639] e1000e 0000:00:1f.6 net00: Setting page 0x6140
[ 4162.606690] e1000e 0000:00:1f.6 net00: reading PHY page 778 (or 0x6140 shifted) reg 0x10
[ 4162.606742] e1000e 0000:00:1f.6 net00: reading PHY page 778 (or 0x6140 shifted) reg 0x11
[ 4162.606794] e1000e 0000:00:1f.6 net00: reading PHY page 778 (or 0x6140 shifted) reg 0x12
[ 4162.606846] e1000e 0000:00:1f.6 net00: reading PHY page 778 (or 0x6140 shifted) reg 0x13
[ 4162.606897] e1000e 0000:00:1f.6 net00: reading PHY page 778 (or 0x6140 shifted) reg 0x14
[ 4162.606949] e1000e 0000:00:1f.6 net00: reading PHY page 778 (or 0x6140 shifted) reg 0x15
[ 4162.607001] e1000e 0000:00:1f.6 net00: reading PHY page 778 (or 0x6140 shifted) reg 0x17
[ 4162.607053] e1000e 0000:00:1f.6 net00: reading PHY page 778 (or 0x6140 shifted) reg 0x18
[ 4162.607119] e1000e 0000:00:1f.6 net00: reading PHY page 778 (or 0x6140 shifted) reg 0x19
[ 4162.607170] e1000e 0000:00:1f.6 net00: reading PHY page 778 (or 0x6140 shifted) reg 0x1a
[ 4162.607222] e1000e 0000:00:1f.6 net00: reading PHY page 778 (or 0x6140 shifted) reg 0x1b
[ 4162.607274] e1000e 0000:00:1f.6 net00: reading PHY page 778 (or 0x6140 shifted) reg 0x1c
[ 4162.607326] e1000e 0000:00:1f.6 net00: reading PHY page 778 (or 0x6140 shifted) reg 0x1d
[ 4162.607377] e1000e 0000:00:1f.6 net00: reading PHY page 778 (or 0x6140 shifted) reg 0x1e
[ 4162.607464] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4162.607520] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x10
[ 4162.607571] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4162.607623] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x11
[ 4162.607679] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4162.607735] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4162.607788] e1000e 0000:00:1f.6 net00: Phy info is only valid if link is up
[ 4162.607913] e1000e 0000:00:1f.6 net00: Setting page 0x6020
[ 4162.607965] e1000e 0000:00:1f.6 net00: reading PHY page 769 (or 0x6020 shifted) reg 0x14
[ 4162.608021] e1000e 0000:00:1f.6 net00: Setting page 0x6020
[ 4162.608073] e1000e 0000:00:1f.6 net00: writing PHY page 769 (or 0x6020 shifted) reg 0x14
[ 4162.608164] e1000e 0000:00:1f.6 net00: Setting page 0x6020
[ 4162.608216] e1000e 0000:00:1f.6 net00: reading PHY page 769 (or 0x6020 shifted) reg 0x17
[ 4162.608272] e1000e 0000:00:1f.6 net00: Setting page 0x6020
[ 4162.608323] e1000e 0000:00:1f.6 net00: writing PHY page 769 (or 0x6020 shifted) reg 0x17
[ 4162.608379] e1000e 0000:00:1f.6 net00: Setting page 0x6020
[ 4162.608443] e1000e 0000:00:1f.6 net00: reading PHY page 769 (or 0x6020 shifted) reg 0x10
[ 4162.608499] e1000e 0000:00:1f.6 net00: Setting page 0x6020
[ 4162.608551] e1000e 0000:00:1f.6 net00: writing PHY page 769 (or 0x6020 shifted) reg 0x10
[ 4162.608607] e1000e 0000:00:1f.6 net00: Setting page 0x6100
[ 4162.608658] e1000e 0000:00:1f.6 net00: reading PHY page 776 (or 0x6100 shifted) reg 0x14
[ 4162.608714] e1000e 0000:00:1f.6 net00: Setting page 0x6100
[ 4162.608766] e1000e 0000:00:1f.6 net00: writing PHY page 776 (or 0x6100 shifted) reg 0x14
[ 4162.608822] e1000e 0000:00:1f.6 net00: Setting page 0x6100
[ 4162.608874] e1000e 0000:00:1f.6 net00: writing PHY page 776 (or 0x6100 shifted) reg 0x17
[ 4162.608929] e1000e 0000:00:1f.6 net00: Setting page 0x6040
[ 4162.608981] e1000e 0000:00:1f.6 net00: reading PHY page 770 (or 0x6040 shifted) reg 0x11
[ 4162.609037] e1000e 0000:00:1f.6 net00: Setting page 0x6040
[ 4162.609089] e1000e 0000:00:1f.6 net00: writing PHY page 770 (or 0x6040 shifted) reg 0x11
[ 4162.609144] e1000e 0000:00:1f.6 net00: Setting page 0x6020
[ 4162.609196] e1000e 0000:00:1f.6 net00: writing PHY page 769 (or 0x6020 shifted) reg 0x14
[ 4162.621345] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4162.621402] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4162.678614] usb 1-10: USB disconnect, device number 5
[ 4164.644462] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4164.644531] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4165.502355] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 4165.613627] ata1.00: configured for UDMA/133
[ 4165.883462] usb 1-10: new high-speed USB device number 6 using xhci_hcd
[ 4166.015186] usb-storage 1-10:1.0: USB Mass Storage device detected
[ 4166.015605] scsi host4: usb-storage 1-10:1.0
[ 4166.692461] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4166.692518] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4166.692573] e1000e 0000:00:1f.6 net00: 1000 Mbps, Full Duplex
[ 4166.692577] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4166.692629] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x10
[ 4166.692681] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4166.692733] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x11
[ 4166.692784] e1000e 0000:00:1f.6 net00: Setting page 0x6080
[ 4166.692836] e1000e 0000:00:1f.6 net00: reading PHY page 772 (or 0x6080 shifted) reg 0x1c
[ 4166.692888] e1000e 0000:00:1f.6 net00: Setting page 0x6080
[ 4166.692939] e1000e 0000:00:1f.6 net00: writing PHY page 772 (or 0x6080 shifted) reg 0x1c
[ 4166.692995] e1000e 0000:00:1f.6 net00: Setting page 0x6100
[ 4166.693047] e1000e 0000:00:1f.6 net00: reading PHY page 776 (or 0x6100 shifted) reg 0x14
[ 4166.693099] e1000e 0000:00:1f.6 net00: Setting page 0x6100
[ 4166.693150] e1000e 0000:00:1f.6 net00: writing PHY page 776 (or 0x6100 shifted) reg 0x14
[ 4166.693206] e1000e 0000:00:1f.6 net00: 1000 Mbps, Full Duplex
[ 4166.693216] e1000e 0000:00:1f.6 net00: Setting page 0x6080
[ 4166.693268] e1000e 0000:00:1f.6 net00: reading PHY page 772 (or 0x6080 shifted) reg 0x14
[ 4166.693325] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4166.693377] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x10
[ 4166.693429] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4166.693496] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x11
[ 4166.693547] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4166.693599] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x10
[ 4166.693651] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4166.693702] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x11
[ 4166.693754] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4166.693806] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x10
[ 4166.693858] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4166.693909] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x11
[ 4166.693961] e1000e 0000:00:1f.6 net00: Setting page 0x6080
[ 4166.694013] e1000e 0000:00:1f.6 net00: writing PHY page 772 (or 0x6080 shifted) reg 0x14
[ 4166.694070] e1000e 0000:00:1f.6 net00: hw->fc.current_mode = 3
[ 4166.694073] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4166.694129] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4166.694185] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x4
[ 4166.694241] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x5
[ 4166.694295] e1000e 0000:00:1f.6 net00: Flow Control = NONE.
[ 4166.694297] e1000e 0000:00:1f.6 net00: 1000 Mbps, Full Duplex
[ 4166.694299] e1000e 0000:00:1f.6 net00: hw->fc.current_mode = 0
[ 4167.077213] scsi 4:0:0:0: Direct-Access Linux File-CD Gadget 0000 PQ: 0 ANSI: 2
[ 4167.077658] sd 4:0:0:0: Attached scsi generic sg2 type 0
[ 4167.078152] sd 4:0:0:0: Power-on or device reset occurred
[ 4167.079721] sd 4:0:0:0: [sdb] Attached SCSI removable disk
[ 4168.694508] e1000e 0000:00:1f.6 net00: Error in exiting dmoff
[ 4168.694527] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x0
[ 4168.694588] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4168.694644] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x4
[ 4168.694700] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x5
[ 4168.694756] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x6
[ 4168.694812] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x9
[ 4168.694867] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0xa
[ 4168.694923] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0xf
[ 4168.694978] e1000e 0000:00:1f.6 net00: 1000 Mbps, Full Duplex
[ 4168.694980] e1000e: net00 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None
[ 4170.916550] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4170.916607] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1
[ 4170.916663] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4170.916715] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1a
[ 4170.916770] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4170.916822] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1a
[ 4170.916878] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4170.916929] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x1f
[ 4170.916985] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0xa
[ 4170.917041] e1000e 0000:00:1f.6 net00: Setting page 0x6080
[ 4170.917093] e1000e 0000:00:1f.6 net00: reading PHY page 772 (or 0x6080 shifted) reg 0x14
[ 4170.917145] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4170.917196] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x10
[ 4170.917248] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4170.917307] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x11
[ 4170.917372] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4170.917425] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x10
[ 4170.917477] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4170.917528] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x11
[ 4170.917585] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4170.917636] e1000e 0000:00:1f.6 net00: writing PHY page 0 (or 0x0 shifted) reg 0x10
[ 4170.917688] e1000e 0000:00:1f.6 net00: Setting page 0x0
[ 4170.917740] e1000e 0000:00:1f.6 net00: reading PHY page 0 (or 0x0 shifted) reg 0x11
[ 4170.917792] e1000e 0000:00:1f.6 net00: Setting page 0x6080
[ 4170.917843] e1000e 0000:00:1f.6 net00: writing PHY page 772 (or 0x6080 shifted) reg 0x14
[ 4770.441271] TCP: net00: Driver has suspect GRO implementation, TCP performance may be compromised.
[-- Attachment #2: S/MIME Cryptographic Signature --]
[-- Type: application/pkcs7-signature, Size: 5174 bytes --]
^ permalink raw reply [flat|nested] 5+ messages in thread
* RE: MDI errors during resume from ACPI S3 (suspend to ram)
2019-08-06 15:36 MDI errors during resume from ACPI S3 (suspend to ram) Paul Menzel
@ 2019-08-06 15:53 ` Mario.Limonciello
2019-08-07 7:23 ` [Intel-wired-lan] " Neftin, Sasha
0 siblings, 1 reply; 5+ messages in thread
From: Mario.Limonciello @ 2019-08-06 15:53 UTC (permalink / raw)
To: pmenzel, jeffrey.t.kirsher; +Cc: intel-wired-lan, linux-kernel
> -----Original Message-----
> From: Paul Menzel <pmenzel@molgen.mpg.de>
> Sent: Tuesday, August 6, 2019 10:36 AM
> To: Jeff Kirsher
> Cc: intel-wired-lan@lists.osuosl.org; Linux Kernel Mailing List; Limonciello, Mario
> Subject: MDI errors during resume from ACPI S3 (suspend to ram)
>
> Dear Linux folks,
>
>
> Trying to decrease the resume time of Linux 5.3-rc3 on the Dell OptiPlex
> 5040 with the device below
>
> $ lspci -nn -s 00:1f.6
> 00:1f.6 Ethernet controller [0200]: Intel Corporation Ethernet Connection (2)
> I219-V [8086:15b8] (rev 31)
>
> pm-graph’s script `sleepgraph.py` shows, that the driver *e1000e* takes
> around 400 ms, which is quite a lot. The call graph trace shows that
> `e1000e_read_phy_reg_mdic()` is responsible for a lot of those. From
> `drivers/net/ethernet/intel/e1000e/phy.c` [1]:
>
> for (i = 0; i < (E1000_GEN_POLL_TIMEOUT * 3); i++) {
> udelay(50);
> mdic = er32(MDIC);
> if (mdic & E1000_MDIC_READY)
> break;
> }
> if (!(mdic & E1000_MDIC_READY)) {
> e_dbg("MDI Read did not complete\n");
> return -E1000_ERR_PHY;
> }
> if (mdic & E1000_MDIC_ERROR) {
> e_dbg("MDI Error\n");
> return -E1000_ERR_PHY;
> }
>
> Unfortunately, errors are not logged if dynamic debug is disabled,
> so rebuilding the Linux kernel with `CONFIG_DYNAMIC_DEBUG`, and
>
> echo "file drivers/net/ethernet/* +p" | sudo tee
> /sys/kernel/debug/dynamic_debug/control
>
> I got the messages below.
>
> [ 4159.204192] e1000e 0000:00:1f.6 net00: MDI Error
> [ 4160.267950] e1000e 0000:00:1f.6 net00: MDI Write did not complete
> [ 4160.359855] e1000e 0000:00:1f.6 net00: MDI Error
>
> Can you please shed a little more light into these errors? Please
> find the full log attached.
>
>
> Kind regards,
>
> Paul
>
>
> [1]:
> https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/drivers/n
> et/ethernet/intel/e1000e/phy.c#n206
Strictly as a reference point you may consider trying the out-of-tree driver to see if these
behaviors persist.
https://sourceforge.net/projects/e1000/
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [Intel-wired-lan] MDI errors during resume from ACPI S3 (suspend to ram)
2019-08-06 15:53 ` Mario.Limonciello
@ 2019-08-07 7:23 ` Neftin, Sasha
2019-08-07 14:55 ` Paul Menzel
0 siblings, 1 reply; 5+ messages in thread
From: Neftin, Sasha @ 2019-08-07 7:23 UTC (permalink / raw)
To: Mario.Limonciello, pmenzel, jeffrey.t.kirsher
Cc: intel-wired-lan, linux-kernel
On 8/6/2019 18:53, Mario.Limonciello@dell.com wrote:
>> -----Original Message-----
>> From: Paul Menzel <pmenzel@molgen.mpg.de>
>> Sent: Tuesday, August 6, 2019 10:36 AM
>> To: Jeff Kirsher
>> Cc: intel-wired-lan@lists.osuosl.org; Linux Kernel Mailing List; Limonciello, Mario
>> Subject: MDI errors during resume from ACPI S3 (suspend to ram)
>>
>> Dear Linux folks,
>>
>>
>> Trying to decrease the resume time of Linux 5.3-rc3 on the Dell OptiPlex
>> 5040 with the device below
>>
>> $ lspci -nn -s 00:1f.6
>> 00:1f.6 Ethernet controller [0200]: Intel Corporation Ethernet Connection (2)
>> I219-V [8086:15b8] (rev 31)
>>
>> pm-graph’s script `sleepgraph.py` shows, that the driver *e1000e* takes
>> around 400 ms, which is quite a lot. The call graph trace shows that
>> `e1000e_read_phy_reg_mdic()` is responsible for a lot of those. From
>> `drivers/net/ethernet/intel/e1000e/phy.c` [1]:
>>
>> for (i = 0; i < (E1000_GEN_POLL_TIMEOUT * 3); i++) {
>> udelay(50);
>> mdic = er32(MDIC);
>> if (mdic & E1000_MDIC_READY)
>> break;
>> }
>> if (!(mdic & E1000_MDIC_READY)) {
>> e_dbg("MDI Read did not complete\n");
>> return -E1000_ERR_PHY;
>> }
>> if (mdic & E1000_MDIC_ERROR) {
>> e_dbg("MDI Error\n");
>> return -E1000_ERR_PHY;
>> }
>>
>> Unfortunately, errors are not logged if dynamic debug is disabled,
>> so rebuilding the Linux kernel with `CONFIG_DYNAMIC_DEBUG`, and
>>
>> echo "file drivers/net/ethernet/* +p" | sudo tee
>> /sys/kernel/debug/dynamic_debug/control
>>
>> I got the messages below.
>>
>> [ 4159.204192] e1000e 0000:00:1f.6 net00: MDI Error
>> [ 4160.267950] e1000e 0000:00:1f.6 net00: MDI Write did not complete
>> [ 4160.359855] e1000e 0000:00:1f.6 net00: MDI Error
>>
>> Can you please shed a little more light into these errors? Please
>> find the full log attached.
>>
>>
>> Kind regards,
>>
>> Paul
>>
>>
>> [1]:
>> https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/drivers/n
>> et/ethernet/intel/e1000e/phy.c#n206
>
> Strictly as a reference point you may consider trying the out-of-tree driver to see if these
> behaviors persist.
>
> https://sourceforge.net/projects/e1000/
>
> _______________________________________________
> Intel-wired-lan mailing list
> Intel-wired-lan@osuosl.org
> https://lists.osuosl.org/mailman/listinfo/intel-wired-lan
>
We are using external PHY. Required ~200 ms to complete MDIC transaction
(depended on the project). You need to take to consider this time before
access to the PHY. I do not recommend decrease timer in a
'e1000e_read_phy_reg_mdic()' method. We could hit on wrong MDI access.
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [Intel-wired-lan] MDI errors during resume from ACPI S3 (suspend to ram)
2019-08-07 7:23 ` [Intel-wired-lan] " Neftin, Sasha
@ 2019-08-07 14:55 ` Paul Menzel
2019-08-08 6:10 ` Neftin, Sasha
0 siblings, 1 reply; 5+ messages in thread
From: Paul Menzel @ 2019-08-07 14:55 UTC (permalink / raw)
To: Sasha Neftin, Jeff Kirsher
Cc: Mario Limonciello, intel-wired-lan, linux-kernel
[-- Attachment #1: Type: text/plain, Size: 3324 bytes --]
Dear Sasha,
On 07.08.19 09:23, Neftin, Sasha wrote:
> On 8/6/2019 18:53, Mario.Limonciello@dell.com wrote:
>>> -----Original Message-----
>>> From: Paul Menzel <pmenzel@molgen.mpg.de>
>>> Sent: Tuesday, August 6, 2019 10:36 AM
>>> To: Jeff Kirsher
>>> Cc: intel-wired-lan@lists.osuosl.org; Linux Kernel Mailing List; Limonciello, Mario
>>> Subject: MDI errors during resume from ACPI S3 (suspend to ram)
>>>
>>> Dear Linux folks,
>>>
>>>
>>> Trying to decrease the resume time of Linux 5.3-rc3 on the Dell OptiPlex
>>> 5040 with the device below
>>>
>>> $ lspci -nn -s 00:1f.6
>>> 00:1f.6 Ethernet controller [0200]: Intel Corporation Ethernet Connection (2)
>>> I219-V [8086:15b8] (rev 31)
>>>
>>> pm-graph’s script `sleepgraph.py` shows, that the driver *e1000e* takes
>>> around 400 ms, which is quite a lot. The call graph trace shows that
>>> `e1000e_read_phy_reg_mdic()` is responsible for a lot of those. From
>>> `drivers/net/ethernet/intel/e1000e/phy.c` [1]:
>>>
>>> for (i = 0; i < (E1000_GEN_POLL_TIMEOUT * 3); i++) {
>>> udelay(50);
>>> mdic = er32(MDIC);
>>> if (mdic & E1000_MDIC_READY)
>>> break;
>>> }
>>> if (!(mdic & E1000_MDIC_READY)) {
>>> e_dbg("MDI Read did not complete\n");
>>> return -E1000_ERR_PHY;
>>> }
>>> if (mdic & E1000_MDIC_ERROR) {
>>> e_dbg("MDI Error\n");
>>> return -E1000_ERR_PHY;
>>> }
>>>
>>> Unfortunately, errors are not logged if dynamic debug is disabled,
>>> so rebuilding the Linux kernel with `CONFIG_DYNAMIC_DEBUG`, and
>>>
>>> echo "file drivers/net/ethernet/* +p" | sudo tee
>>> /sys/kernel/debug/dynamic_debug/control
>>>
>>> I got the messages below.
>>>
>>> [ 4159.204192] e1000e 0000:00:1f.6 net00: MDI Error
>>> [ 4160.267950] e1000e 0000:00:1f.6 net00: MDI Write did not complete
>>> [ 4160.359855] e1000e 0000:00:1f.6 net00: MDI Error
>>>
>>> Can you please shed a little more light into these errors? Please
>>> find the full log attached.
>>> [1]: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/drivers/net/ethernet/intel/e1000e/phy.c#n206
>>
>> Strictly as a reference point you may consider trying the out-of-tree driver to see if these
>> behaviors persist.
>>
>> https://sourceforge.net/projects/e1000/
I can try that in the next days.
> We are using external PHY. Required ~200 ms to complete MDIC
> transaction (depended on the project).
Are you referring to the out-of-tree driver?
> You need to take to consider this time before access to the PHY. I do
> not recommend decrease timer in a 'e1000e_read_phy_reg_mdic()'
> method. We could hit on wrong MDI access.
My point was more, if you know that more time is needed, before the MDI
setting(?) will succeed, why try it anyway and go into the error paths?
Isn’t there some polling possible to find out, when MDI can be set up?
Kind regards,
Paul
[-- Attachment #2: S/MIME Cryptographic Signature --]
[-- Type: application/pkcs7-signature, Size: 5174 bytes --]
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [Intel-wired-lan] MDI errors during resume from ACPI S3 (suspend to ram)
2019-08-07 14:55 ` Paul Menzel
@ 2019-08-08 6:10 ` Neftin, Sasha
0 siblings, 0 replies; 5+ messages in thread
From: Neftin, Sasha @ 2019-08-08 6:10 UTC (permalink / raw)
To: Paul Menzel, Jeff Kirsher
Cc: Mario Limonciello, intel-wired-lan, linux-kernel
On 8/7/2019 17:55, Paul Menzel wrote:
>
> Dear Sasha,
>
>
> On 07.08.19 09:23, Neftin, Sasha wrote:
>> On 8/6/2019 18:53, Mario.Limonciello@dell.com wrote:
>>>> -----Original Message-----
>>>> From: Paul Menzel <pmenzel@molgen.mpg.de>
>>>> Sent: Tuesday, August 6, 2019 10:36 AM
>>>> To: Jeff Kirsher
>>>> Cc: intel-wired-lan@lists.osuosl.org; Linux Kernel Mailing List; Limonciello, Mario
>>>> Subject: MDI errors during resume from ACPI S3 (suspend to ram)
>>>>
>>>> Dear Linux folks,
>>>>
>>>>
>>>> Trying to decrease the resume time of Linux 5.3-rc3 on the Dell OptiPlex
>>>> 5040 with the device below
>>>>
>>>> $ lspci -nn -s 00:1f.6
>>>> 00:1f.6 Ethernet controller [0200]: Intel Corporation Ethernet Connection (2)
>>>> I219-V [8086:15b8] (rev 31)
>>>>
>>>> pm-graph’s script `sleepgraph.py` shows, that the driver *e1000e* takes
>>>> around 400 ms, which is quite a lot. The call graph trace shows that
>>>> `e1000e_read_phy_reg_mdic()` is responsible for a lot of those. From
>>>> `drivers/net/ethernet/intel/e1000e/phy.c` [1]:
>>>>
>>>> for (i = 0; i < (E1000_GEN_POLL_TIMEOUT * 3); i++) {
>>>> udelay(50);
>>>> mdic = er32(MDIC);
>>>> if (mdic & E1000_MDIC_READY)
>>>> break;
>>>> }
>>>> if (!(mdic & E1000_MDIC_READY)) {
>>>> e_dbg("MDI Read did not complete\n");
>>>> return -E1000_ERR_PHY;
>>>> }
>>>> if (mdic & E1000_MDIC_ERROR) {
>>>> e_dbg("MDI Error\n");
>>>> return -E1000_ERR_PHY;
>>>> }
>>>>
>>>> Unfortunately, errors are not logged if dynamic debug is disabled,
>>>> so rebuilding the Linux kernel with `CONFIG_DYNAMIC_DEBUG`, and
>>>>
>>>> echo "file drivers/net/ethernet/* +p" | sudo tee
>>>> /sys/kernel/debug/dynamic_debug/control
>>>>
>>>> I got the messages below.
>>>>
>>>> [ 4159.204192] e1000e 0000:00:1f.6 net00: MDI Error
>>>> [ 4160.267950] e1000e 0000:00:1f.6 net00: MDI Write did not complete
>>>> [ 4160.359855] e1000e 0000:00:1f.6 net00: MDI Error
>>>>
>>>> Can you please shed a little more light into these errors? Please
>>>> find the full log attached.
>
>>>> [1]: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/drivers/net/ethernet/intel/e1000e/phy.c#n206
>>>
>>> Strictly as a reference point you may consider trying the out-of-tree driver to see if these
>>> behaviors persist.
>>>
>>> https://sourceforge.net/projects/e1000/
>
> I can try that in the next days.
>
>> We are using external PHY. Required ~200 ms to complete MDIC
>> transaction (depended on the project).
>
> Are you referring to the out-of-tree driver?
>
I believe the out of tree driver have a same approach to MDIC access.
>> You need to take to consider this time before access to the PHY. I do
>> not recommend decrease timer in a 'e1000e_read_phy_reg_mdic()'
>> method. We could hit on wrong MDI access.
> My point was more, if you know that more time is needed, before the MDI
> setting(?) will succeed, why try it anyway and go into the error paths?
> Isn’t there some polling possible to find out, when MDI can be set up?
>
e1000e is very old driver and serve pretty lot of 1G clients. Each 1Gbe
MAC/PHY controller have a different configuration depend platform.
>
> Kind regards,
>
> Paul
>
Hello Paul,
Let me back later with more information specific your device. I will try
find out more details with design team.
^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2019-08-08 6:10 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-08-06 15:36 MDI errors during resume from ACPI S3 (suspend to ram) Paul Menzel
2019-08-06 15:53 ` Mario.Limonciello
2019-08-07 7:23 ` [Intel-wired-lan] " Neftin, Sasha
2019-08-07 14:55 ` Paul Menzel
2019-08-08 6:10 ` Neftin, Sasha
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).