From: Rich Felker <dalias@libc.org>
To: devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
linux-sh@vger.kernel.org
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>,
Kumar Gala <galak@codeaurora.org>,
Mark Rutland <mark.rutland@arm.com>,
Pawel Moll <pawel.moll@arm.com>, Rob Herring <robh+dt@kernel.org>
Subject: [PATCH v2 05/12] of: add J-Core SPI master bindings
Date: Fri, 20 May 2016 02:53:04 +0000 [thread overview]
Message-ID: <32585cfb27d31e9d5cb399ecc4d8b89f4ec5e2cb.1463708766.git.dalias@libc.org> (raw)
In-Reply-To: <cover.1463708766.git.dalias@libc.org>
Signed-off-by: Rich Felker <dalias@libc.org>
---
.../devicetree/bindings/spi/jcore,spi.txt | 23 ++++++++++++++++++++++
1 file changed, 23 insertions(+)
create mode 100644 Documentation/devicetree/bindings/spi/jcore,spi.txt
diff --git a/Documentation/devicetree/bindings/spi/jcore,spi.txt b/Documentation/devicetree/bindings/spi/jcore,spi.txt
new file mode 100644
index 0000000..9055e7d
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/jcore,spi.txt
@@ -0,0 +1,23 @@
+J-Core SPI master
+
+Required properties:
+
+- compatible: Must be "jcore,spi2".
+
+- reg: Memory region for registers.
+
+- #address-cells: Must be 1.
+
+- #size-cells: Must be 0.
+
+See spi-bus.txt for additional properties not specific to this device.
+
+Example:
+
+spi {
+ compatible = "jcore,spi2";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = < 0x40 0x8 >;
+ spi-max-frequency = <12500000>;
+}
--
2.8.1
next prev parent reply other threads:[~2016-05-20 2:53 UTC|newest]
Thread overview: 52+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-05-20 2:53 [PATCH v2 00/12] J-core J2 cpu and SoC peripherals support Rich Felker
2016-05-20 2:53 ` [PATCH v2 02/12] of: add J-Core cpu bindings Rich Felker
2016-05-23 20:48 ` Rob Herring
2016-05-23 21:03 ` Rich Felker
2016-05-23 23:29 ` Rob Herring
2016-05-24 2:39 ` Rich Felker
2016-05-24 21:30 ` Rob Landley
2016-05-25 1:13 ` Rob Herring
2016-05-25 2:33 ` Rich Felker
2016-05-25 13:13 ` Rob Herring
2016-05-20 2:53 ` [PATCH v2 01/12] of: add vendor prefix for J-Core Rich Felker
2016-05-23 20:49 ` Rob Herring
2016-05-20 2:53 ` [PATCH v2 08/12] irqchip: add J-Core AIC driver Rich Felker
2016-05-20 8:08 ` Geert Uytterhoeven
2016-05-20 8:15 ` Marc Zyngier
2016-05-25 4:29 ` Rich Felker
2016-05-20 2:53 ` [PATCH v2 03/12] of: add J-Core interrupt controller bindings Rich Felker
2016-05-20 8:04 ` Geert Uytterhoeven
2016-05-20 22:34 ` Rich Felker
2016-05-21 18:07 ` Geert Uytterhoeven
2016-05-21 19:17 ` Rich Felker
2016-05-23 20:53 ` Rob Herring
2016-05-23 21:13 ` Rich Felker
2016-05-24 8:09 ` Marc Zyngier
2016-05-25 2:25 ` Rich Felker
2016-05-20 2:53 ` [PATCH v2 06/12] sh: add support for J-Core J2 processor Rich Felker
2016-05-20 2:53 ` [PATCH v2 11/12] sh: add defconfig for J-Core J2 Rich Felker
2016-05-20 2:53 ` [PATCH v2 09/12] clocksource: add J-Core PIT/RTC driver Rich Felker
2016-05-20 14:01 ` Daniel Lezcano
2016-05-21 3:15 ` Rich Felker
2016-05-21 15:55 ` Rob Landley
2016-05-23 20:32 ` Daniel Lezcano
2016-05-24 2:25 ` Rich Felker
2016-05-20 2:53 ` [PATCH v2 04/12] of: add J-Core timer bindings Rich Felker
2016-05-20 8:03 ` Geert Uytterhoeven
2016-05-20 2:53 ` [PATCH v2 12/12] sh: add device tree source for J2 FPGA on Mimas v2 board Rich Felker
2016-05-20 8:17 ` Geert Uytterhoeven
2016-05-20 22:42 ` Rich Felker
2016-05-20 2:53 ` [PATCH v2 10/12] spi: add driver for J-Core SPI controller Rich Felker
2016-05-20 8:15 ` Geert Uytterhoeven
2016-05-20 22:50 ` Rich Felker
2016-05-20 10:23 ` Mark Brown
2016-05-20 23:24 ` Rich Felker
2016-05-23 15:30 ` Mark Brown
2016-05-23 20:29 ` Rich Felker
2016-05-23 22:11 ` Mark Brown
2016-05-20 2:53 ` [PATCH v2 07/12] sh: add AT_HWCAP flag for J-Core cas.l instruction Rich Felker
2016-05-20 2:53 ` Rich Felker [this message]
2016-05-20 8:05 ` [PATCH v2 05/12] of: add J-Core SPI master bindings Geert Uytterhoeven
2016-05-23 21:00 ` Rob Herring
2016-05-23 21:06 ` Rich Felker
2016-05-23 23:16 ` Rob Herring
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=32585cfb27d31e9d5cb399ecc4d8b89f4ec5e2cb.1463708766.git.dalias@libc.org \
--to=dalias@libc.org \
--cc=devicetree@vger.kernel.org \
--cc=galak@codeaurora.org \
--cc=ijc+devicetree@hellion.org.uk \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-sh@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=pawel.moll@arm.com \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).