[PATCH 0/7] Miscellaneous Macintosh fixes and clean up

[PATCH 0/7] Miscellaneous Macintosh fixes and clean up

[Finn Thain]

This series has some minor fixes and cleanups under drivers/macintosh,
including a patch to rework recent printk changes in adb-hid.c.
There's also a re-based RTC code de-duplication patch.


Finn Thain (7):
  macintosh: Use common code to access RTC
  macintosh/adb: Rework printk output again
  macintosh/via-macii: Synchronous bus reset
  macintosh/via-macii: Remove BUG_ON assertions
  macintosh/via-macii: Simplify locking
  macintosh/via-macii, macintosh/adb-iop: Modernize printk calls
  macintosh/via-macii, macintosh/adb-iop: Clean up whitespace

 arch/m68k/mac/misc.c                   |  75 +------
 arch/powerpc/platforms/powermac/time.c | 126 ++----------
 drivers/macintosh/adb-iop.c            |  50 +++--
 drivers/macintosh/adb.c                |   8 +-
 drivers/macintosh/adbhid.c             |  53 ++---
 drivers/macintosh/via-cuda.c           |  35 ++++
 drivers/macintosh/via-macii.c          | 352 ++++++++++++++++-----------------
 drivers/macintosh/via-pmu.c            |  33 ++++
 include/linux/cuda.h                   |   4 +
 include/linux/pmu.h                    |   4 +
 10 files changed, 328 insertions(+), 412 deletions(-)

-- 
2.16.4

[PATCH 3/7] macintosh/via-macii: Synchronous bus reset

[Finn Thain]

Make the reset operation synchronous, like the other ADB drivers.
The reset request is static data but callers may not know that.
This way the struct is not in use when the reset method returns.

Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
---
 drivers/macintosh/via-macii.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/macintosh/via-macii.c b/drivers/macintosh/via-macii.c
index cf6f7d52d6be..36a4f49e79b5 100644
--- a/drivers/macintosh/via-macii.c
+++ b/drivers/macintosh/via-macii.c
@@ -331,7 +331,8 @@ static int macii_reset_bus(void)
 		return 0;
 
 	/* Command = 0, Address = ignored */
-	adb_request(&req, NULL, 0, 1, ADB_BUSRESET);
+	adb_request(&req, NULL, ADBREQ_NOSEND, 1, ADB_BUSRESET);
+	macii_send_request(&req, 1);
 
 	/* Don't want any more requests during the Global Reset low time. */
 	udelay(3000);
-- 
2.16.4

[PATCH 7/7] macintosh/via-macii, macintosh/adb-iop: Clean up whitespace

[Finn Thain]

Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
---
 drivers/macintosh/adb-iop.c   |  48 ++++---
 drivers/macintosh/via-macii.c | 286 +++++++++++++++++++++---------------------
 2 files changed, 174 insertions(+), 160 deletions(-)

diff --git a/drivers/macintosh/adb-iop.c b/drivers/macintosh/adb-iop.c
index 3a1e995ecc0e..fca31640e3ef 100644
--- a/drivers/macintosh/adb-iop.c
+++ b/drivers/macintosh/adb-iop.c
@@ -20,13 +20,13 @@
 #include <linux/init.h>
 #include <linux/proc_fs.h>
 
-#include <asm/macintosh.h> 
-#include <asm/macints.h> 
+#include <asm/macintosh.h>
+#include <asm/macints.h>
 #include <asm/mac_iop.h>
 #include <asm/mac_oss.h>
 #include <asm/adb_iop.h>
 
-#include <linux/adb.h> 
+#include <linux/adb.h>
 
 /*#define DEBUG_ADB_IOP*/
 
@@ -38,9 +38,9 @@ static unsigned char *reply_ptr;
 #endif
 
 static enum adb_iop_state {
-    idle,
-    sending,
-    awaiting_reply
+	idle,
+	sending,
+	awaiting_reply
 } adb_iop_state;
 
 static void adb_iop_start(void);
@@ -66,7 +66,8 @@ static void adb_iop_end_req(struct adb_request *req, int state)
 {
 	req->complete = 1;
 	current_req = req->next;
-	if (req->done) (*req->done)(req);
+	if (req->done)
+		(*req->done)(req);
 	adb_iop_state = state;
 }
 
@@ -100,7 +101,7 @@ static void adb_iop_complete(struct iop_msg *msg)
 
 static void adb_iop_listen(struct iop_msg *msg)
 {
-	struct adb_iopmsg *amsg = (struct adb_iopmsg *) msg->message;
+	struct adb_iopmsg *amsg = (struct adb_iopmsg *)msg->message;
 	struct adb_request *req;
 	unsigned long flags;
 #ifdef DEBUG_ADB_IOP
@@ -113,9 +114,9 @@ static void adb_iop_listen(struct iop_msg *msg)
 
 #ifdef DEBUG_ADB_IOP
 	printk("adb_iop_listen %p: rcvd packet, %d bytes: %02X %02X", req,
-		(uint) amsg->count + 2, (uint) amsg->flags, (uint) amsg->cmd);
+	       (uint)amsg->count + 2, (uint)amsg->flags, (uint)amsg->cmd);
 	for (i = 0; i < amsg->count; i++)
-		printk(" %02X", (uint) amsg->data[i]);
+		printk(" %02X", (uint)amsg->data[i]);
 	printk("\n");
 #endif
 
@@ -168,14 +169,15 @@ static void adb_iop_start(void)
 
 	/* get the packet to send */
 	req = current_req;
-	if (!req) return;
+	if (!req)
+		return;
 
 	local_irq_save(flags);
 
 #ifdef DEBUG_ADB_IOP
 	printk("adb_iop_start %p: sending packet, %d bytes:", req, req->nbytes);
-	for (i = 0 ; i < req->nbytes ; i++)
-		printk(" %02X", (uint) req->data[i]);
+	for (i = 0; i < req->nbytes; i++)
+		printk(" %02X", (uint)req->data[i]);
 	printk("\n");
 #endif
 
@@ -196,13 +198,14 @@ static void adb_iop_start(void)
 	/* Now send it. The IOP manager will call adb_iop_complete */
 	/* when the packet has been sent.                          */
 
-	iop_send_message(ADB_IOP, ADB_CHAN, req,
-			 sizeof(amsg), (__u8 *) &amsg, adb_iop_complete);
+	iop_send_message(ADB_IOP, ADB_CHAN, req, sizeof(amsg), (__u8 *)&amsg,
+			 adb_iop_complete);
 }
 
 int adb_iop_probe(void)
 {
-	if (!iop_ism_present) return -ENODEV;
+	if (!iop_ism_present)
+		return -ENODEV;
 	return 0;
 }
 
@@ -218,10 +221,12 @@ int adb_iop_send_request(struct adb_request *req, int sync)
 	int err;
 
 	err = adb_iop_write(req);
-	if (err) return err;
+	if (err)
+		return err;
 
 	if (sync) {
-		while (!req->complete) adb_iop_poll();
+		while (!req->complete)
+			adb_iop_poll();
 	}
 	return 0;
 }
@@ -251,7 +256,9 @@ static int adb_iop_write(struct adb_request *req)
 	}
 
 	local_irq_restore(flags);
-	if (adb_iop_state == idle) adb_iop_start();
+
+	if (adb_iop_state == idle)
+		adb_iop_start();
 	return 0;
 }
 
@@ -263,7 +270,8 @@ int adb_iop_autopoll(int devs)
 
 void adb_iop_poll(void)
 {
-	if (adb_iop_state == idle) adb_iop_start();
+	if (adb_iop_state == idle)
+		adb_iop_start();
 	iop_ism_irq_poll(ADB_IOP);
 }
 
diff --git a/drivers/macintosh/via-macii.c b/drivers/macintosh/via-macii.c
index a38f57ba50cb..ac824d7b2dcf 100644
--- a/drivers/macintosh/via-macii.c
+++ b/drivers/macintosh/via-macii.c
@@ -12,7 +12,7 @@
  *
  * 1999-08-02 (jmt) - Initial rewrite for Unified ADB.
  * 2000-03-29 Tony Mantler <tonym@mac.linux-m68k.org>
- * 				- Big overhaul, should actually work now.
+ *            - Big overhaul, should actually work now.
  * 2006-12-31 Finn Thain - Another overhaul.
  *
  * Suggested reading:
@@ -23,7 +23,7 @@
  * Apple's "ADB Analyzer" bus sniffer is invaluable:
  *   ftp://ftp.apple.com/developer/Tool_Chest/Devices_-_Hardware/Apple_Desktop_Bus/
  */
- 
+
 #include <stdarg.h>
 #include <linux/types.h>
 #include <linux/errno.h>
@@ -77,7 +77,7 @@ static volatile unsigned char *via;
 #define ST_ODD		0x20		/* ADB state: odd data byte */
 #define ST_IDLE		0x30		/* ADB state: idle, nothing to send */
 
-static int  macii_init_via(void);
+static int macii_init_via(void);
 static void macii_start(void);
 static irqreturn_t macii_interrupt(int irq, void *arg);
 static void macii_queue_poll(void);
@@ -123,7 +123,8 @@ static int autopoll_devs;      /* bits set are device addresses to be polled */
 /* Check for MacII style ADB */
 static int macii_probe(void)
 {
-	if (macintosh_config->adb_type != MAC_ADB_II) return -ENODEV;
+	if (macintosh_config->adb_type != MAC_ADB_II)
+		return -ENODEV;
 
 	via = via1;
 
@@ -136,15 +137,17 @@ int macii_init(void)
 {
 	unsigned long flags;
 	int err;
-	
+
 	local_irq_save(flags);
-	
+
 	err = macii_init_via();
-	if (err) goto out;
+	if (err)
+		goto out;
 
 	err = request_irq(IRQ_MAC_ADB, macii_interrupt, 0, "ADB",
 			  macii_interrupt);
-	if (err) goto out;
+	if (err)
+		goto out;
 
 	macii_state = idle;
 out:
@@ -152,7 +155,7 @@ int macii_init(void)
 	return err;
 }
 
-/* initialize the hardware */	
+/* initialize the hardware */
 static int macii_init_via(void)
 {
 	unsigned char x;
@@ -162,7 +165,7 @@ static int macii_init_via(void)
 
 	/* Set up state: idle */
 	via[B] |= ST_IDLE;
-	last_status = via[B] & (ST_MASK|CTLR_IRQ);
+	last_status = via[B] & (ST_MASK | CTLR_IRQ);
 
 	/* Shift register on input */
 	via[ACR] = (via[ACR] & ~SR_CTRL) | SR_EXT;
@@ -188,7 +191,8 @@ static void macii_queue_poll(void)
 	int next_device;
 	static struct adb_request req;
 
-	if (!autopoll_devs) return;
+	if (!autopoll_devs)
+		return;
 
 	device_mask = (1 << (((command_byte & 0xF0) >> 4) + 1)) - 1;
 	if (autopoll_devs & ~device_mask)
@@ -196,8 +200,7 @@ static void macii_queue_poll(void)
 	else
 		next_device = ffs(autopoll_devs) - 1;
 
-	adb_request(&req, NULL, ADBREQ_NOSEND, 1,
-	            ADB_READREG(next_device, 0));
+	adb_request(&req, NULL, ADBREQ_NOSEND, 1, ADB_READREG(next_device, 0));
 
 	req.sent = 0;
 	req.complete = 0;
@@ -237,7 +240,7 @@ static int macii_write(struct adb_request *req)
 		req->complete = 1;
 		return -EINVAL;
 	}
-	
+
 	req->next = NULL;
 	req->sent = 0;
 	req->complete = 0;
@@ -251,7 +254,8 @@ static int macii_write(struct adb_request *req)
 	} else {
 		current_req = req;
 		last_req = req;
-		if (macii_state == idle) macii_start();
+		if (macii_state == idle)
+			macii_start();
 	}
 
 	local_irq_restore(flags);
@@ -269,7 +273,8 @@ static int macii_autopoll(int devs)
 	/* bit 1 == device 1, and so on. */
 	autopoll_devs = devs & 0xFFFE;
 
-	if (!autopoll_devs) return 0;
+	if (!autopoll_devs)
+		return 0;
 
 	local_irq_save(flags);
 
@@ -286,7 +291,8 @@ static int macii_autopoll(int devs)
 	return err;
 }
 
-static inline int need_autopoll(void) {
+static inline int need_autopoll(void)
+{
 	/* Was the last command Talk Reg 0
 	 * and is the target on the autopoll list?
 	 */
@@ -306,7 +312,7 @@ static void macii_poll(void)
 static int macii_reset_bus(void)
 {
 	static struct adb_request req;
-	
+
 	/* Command = 0, Address = ignored */
 	adb_request(&req, NULL, ADBREQ_NOSEND, 1, ADB_BUSRESET);
 	macii_send_request(&req, 1);
@@ -349,7 +355,7 @@ static void macii_start(void)
  * to be activity on the ADB bus. The chip will poll to achieve this.
  *
  * The basic ADB state machine was left unchanged from the original MacII code
- * by Alan Cox, which was based on the CUDA driver for PowerMac. 
+ * by Alan Cox, which was based on the CUDA driver for PowerMac.
  * The syntax of the ADB status lines is totally different on MacII,
  * though. MacII uses the states Command -> Even -> Odd -> Even ->...-> Idle
  * for sending and Idle -> Even -> Odd -> Even ->...-> Idle for receiving.
@@ -377,147 +383,147 @@ static irqreturn_t macii_interrupt(int irq, void *arg)
 	}
 
 	last_status = status;
-	status = via[B] & (ST_MASK|CTLR_IRQ);
+	status = via[B] & (ST_MASK | CTLR_IRQ);
 
 	switch (macii_state) {
-		case idle:
-			if (reading_reply) {
-				reply_ptr = current_req->reply;
-			} else {
-				WARN_ON(current_req);
-				reply_ptr = reply_buf;
-			}
+	case idle:
+		if (reading_reply) {
+			reply_ptr = current_req->reply;
+		} else {
+			WARN_ON(current_req);
+			reply_ptr = reply_buf;
+		}
 
-			x = via[SR];
+		x = via[SR];
 
-			if ((status & CTLR_IRQ) && (x == 0xFF)) {
-				/* Bus timeout without SRQ sequence:
-				 *     data is "FF" while CTLR_IRQ is "H"
-				 */
-				reply_len = 0;
-				srq_asserted = 0;
-				macii_state = read_done;
-			} else {
-				macii_state = reading;
-				*reply_ptr = x;
-				reply_len = 1;
-			}
+		if ((status & CTLR_IRQ) && (x == 0xFF)) {
+			/* Bus timeout without SRQ sequence:
+			 *     data is "FF" while CTLR_IRQ is "H"
+			 */
+			reply_len = 0;
+			srq_asserted = 0;
+			macii_state = read_done;
+		} else {
+			macii_state = reading;
+			*reply_ptr = x;
+			reply_len = 1;
+		}
 
-			/* set ADB state = even for first data byte */
-			via[B] = (via[B] & ~ST_MASK) | ST_EVEN;
-			break;
+		/* set ADB state = even for first data byte */
+		via[B] = (via[B] & ~ST_MASK) | ST_EVEN;
+		break;
 
-		case sending:
-			req = current_req;
-			if (data_index >= req->nbytes) {
-				req->sent = 1;
-				macii_state = idle;
-
-				if (req->reply_expected) {
-					reading_reply = 1;
-				} else {
-					req->complete = 1;
-					current_req = req->next;
-					if (req->done) (*req->done)(req);
-
-					if (current_req)
-						macii_start();
-					else
-						if (need_autopoll())
-							macii_autopoll(autopoll_devs);
-				}
+	case sending:
+		req = current_req;
+		if (data_index >= req->nbytes) {
+			req->sent = 1;
+			macii_state = idle;
 
-				if (macii_state == idle) {
-					/* reset to shift in */
-					via[ACR] &= ~SR_OUT;
-					x = via[SR];
-					/* set ADB state idle - might get SRQ */
-					via[B] = (via[B] & ~ST_MASK) | ST_IDLE;
-				}
+			if (req->reply_expected) {
+				reading_reply = 1;
 			} else {
-				via[SR] = req->data[data_index++];
-
-				if ( (via[B] & ST_MASK) == ST_CMD ) {
-					/* just sent the command byte, set to EVEN */
-					via[B] = (via[B] & ~ST_MASK) | ST_EVEN;
-				} else {
-					/* invert state bits, toggle ODD/EVEN */
-					via[B] ^= ST_MASK;
-				}
-			}
-			break;
-
-		case reading:
-			x = via[SR];
-			WARN_ON((status & ST_MASK) == ST_CMD ||
-				(status & ST_MASK) == ST_IDLE);
-
-			/* Bus timeout with SRQ sequence:
-			 *     data is "XX FF"      while CTLR_IRQ is "L L"
-			 * End of packet without SRQ sequence:
-			 *     data is "XX...YY 00" while CTLR_IRQ is "L...H L"
-			 * End of packet SRQ sequence:
-			 *     data is "XX...YY 00" while CTLR_IRQ is "L...L L"
-			 * (where XX is the first response byte and
-			 * YY is the last byte of valid response data.)
-			 */
+				req->complete = 1;
+				current_req = req->next;
+				if (req->done)
+					(*req->done)(req);
 
-			srq_asserted = 0;
-			if (!(status & CTLR_IRQ)) {
-				if (x == 0xFF) {
-					if (!(last_status & CTLR_IRQ)) {
-						macii_state = read_done;
-						reply_len = 0;
-						srq_asserted = 1;
-					}
-				} else if (x == 0x00) {
-					macii_state = read_done;
-					if (!(last_status & CTLR_IRQ))
-						srq_asserted = 1;
-				}
+				if (current_req)
+					macii_start();
+				else if (need_autopoll())
+					macii_autopoll(autopoll_devs);
 			}
 
-			if (macii_state == reading &&
-			    reply_len < ARRAY_SIZE(reply_buf)) {
-				reply_ptr++;
-				*reply_ptr = x;
-				reply_len++;
+			if (macii_state == idle) {
+				/* reset to shift in */
+				via[ACR] &= ~SR_OUT;
+				x = via[SR];
+				/* set ADB state idle - might get SRQ */
+				via[B] = (via[B] & ~ST_MASK) | ST_IDLE;
 			}
+		} else {
+			via[SR] = req->data[data_index++];
 
-			/* invert state bits, toggle ODD/EVEN */
-			via[B] ^= ST_MASK;
-			break;
+			if ((via[B] & ST_MASK) == ST_CMD) {
+				/* just sent the command byte, set to EVEN */
+				via[B] = (via[B] & ~ST_MASK) | ST_EVEN;
+			} else {
+				/* invert state bits, toggle ODD/EVEN */
+				via[B] ^= ST_MASK;
+			}
+		}
+		break;
 
-		case read_done:
-			x = via[SR];
+	case reading:
+		x = via[SR];
+		WARN_ON((status & ST_MASK) == ST_CMD ||
+			(status & ST_MASK) == ST_IDLE);
+
+		/* Bus timeout with SRQ sequence:
+		 *     data is "XX FF"      while CTLR_IRQ is "L L"
+		 * End of packet without SRQ sequence:
+		 *     data is "XX...YY 00" while CTLR_IRQ is "L...H L"
+		 * End of packet SRQ sequence:
+		 *     data is "XX...YY 00" while CTLR_IRQ is "L...L L"
+		 * (where XX is the first response byte and
+		 * YY is the last byte of valid response data.)
+		 */
 
-			if (reading_reply) {
-				reading_reply = 0;
-				req = current_req;
-				req->reply_len = reply_len;
-				req->complete = 1;
-				current_req = req->next;
-				if (req->done) (*req->done)(req);
-			} else if (reply_len && autopoll_devs)
-				adb_input(reply_buf, reply_len, 0);
+		srq_asserted = 0;
+		if (!(status & CTLR_IRQ)) {
+			if (x == 0xFF) {
+				if (!(last_status & CTLR_IRQ)) {
+					macii_state = read_done;
+					reply_len = 0;
+					srq_asserted = 1;
+				}
+			} else if (x == 0x00) {
+				macii_state = read_done;
+				if (!(last_status & CTLR_IRQ))
+					srq_asserted = 1;
+			}
+		}
 
-			macii_state = idle;
+		if (macii_state == reading &&
+		    reply_len < ARRAY_SIZE(reply_buf)) {
+			reply_ptr++;
+			*reply_ptr = x;
+			reply_len++;
+		}
 
-			/* SRQ seen before, initiate poll now */
-			if (srq_asserted)
-				macii_queue_poll();
+		/* invert state bits, toggle ODD/EVEN */
+		via[B] ^= ST_MASK;
+		break;
 
-			if (current_req)
-				macii_start();
-			else
-				if (need_autopoll())
-					macii_autopoll(autopoll_devs);
+	case read_done:
+		x = via[SR];
 
-			if (macii_state == idle)
-				via[B] = (via[B] & ~ST_MASK) | ST_IDLE;
-			break;
+		if (reading_reply) {
+			reading_reply = 0;
+			req = current_req;
+			req->reply_len = reply_len;
+			req->complete = 1;
+			current_req = req->next;
+			if (req->done)
+				(*req->done)(req);
+		} else if (reply_len && autopoll_devs)
+			adb_input(reply_buf, reply_len, 0);
+
+		macii_state = idle;
+
+		/* SRQ seen before, initiate poll now */
+		if (srq_asserted)
+			macii_queue_poll();
+
+		if (current_req)
+			macii_start();
+		else if (need_autopoll())
+			macii_autopoll(autopoll_devs);
+
+		if (macii_state == idle)
+			via[B] = (via[B] & ~ST_MASK) | ST_IDLE;
+		break;
 
-		default:
+	default:
 		break;
 	}
 
-- 
2.16.4

[PATCH 1/7] macintosh: Use common code to access RTC

[Finn Thain]

Now that the 68k Mac port has adopted the via-pmu driver, the same RTC
code can be shared between m68k and powerpc. Replace duplicated code in
arch/powerpc and arch/m68k with common RTC accessors for Cuda and PMU.

Drop the problematic WARN_ON which was introduced in commit 22db552b50fa
("powerpc/powermac: Fix rtc read/write functions").

Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Arnd Bergmann <arnd@arndb.de>
---
This patch has been regression tested on the following Mac models.
  Centris 660av       (m68k, Cuda)
  PowerBook 190       (m68k, PMU)
  Beige G3 PowerMac   (powerpc, Cuda)
  Pismo G3 PowerBook  (powerpc, PMU)
  G5 PowerMac         (powerpc64, PMU)

These changes were previously submitted as "[RFC] macintosh: Use common
code to access RTC", and prior to that as "[PATCH v3 10/12] macintosh:
Use common code to access RTC", etc.

Changes since RFC:
- pmac_get_rtc_time() is no longer defined terms of pmac_get_boot_time().
- The 64-bit temporary variables were replaced with 64-bit casts,
  consistent with via_read_time() and via_set_rtc_time().
- Rebased.

Changes since v3:
- Rearranged some #ifdefs in arch/powerpc/platforms/powermac/time.c so
  that pmac_set_rtc_time() will return -ENODEV when appropriate.
- Rebased.
---
 arch/m68k/mac/misc.c                   |  75 +++-----------------
 arch/powerpc/platforms/powermac/time.c | 126 ++++++---------------------------
 drivers/macintosh/via-cuda.c           |  35 +++++++++
 drivers/macintosh/via-pmu.c            |  33 +++++++++
 include/linux/cuda.h                   |   4 ++
 include/linux/pmu.h                    |   4 ++
 6 files changed, 106 insertions(+), 171 deletions(-)

diff --git a/arch/m68k/mac/misc.c b/arch/m68k/mac/misc.c
index 1b083c500b9a..ebb3b6d169ea 100644
--- a/arch/m68k/mac/misc.c
+++ b/arch/m68k/mac/misc.c
@@ -37,35 +37,6 @@
 static void (*rom_reset)(void);
 
 #ifdef CONFIG_ADB_CUDA
-static time64_t cuda_read_time(void)
-{
-	struct adb_request req;
-	time64_t time;
-
-	if (cuda_request(&req, NULL, 2, CUDA_PACKET, CUDA_GET_TIME) < 0)
-		return 0;
-	while (!req.complete)
-		cuda_poll();
-
-	time = (u32)((req.reply[3] << 24) | (req.reply[4] << 16) |
-		     (req.reply[5] << 8) | req.reply[6]);
-
-	return time - RTC_OFFSET;
-}
-
-static void cuda_write_time(time64_t time)
-{
-	struct adb_request req;
-	u32 data = lower_32_bits(time + RTC_OFFSET);
-
-	if (cuda_request(&req, NULL, 6, CUDA_PACKET, CUDA_SET_TIME,
-			 (data >> 24) & 0xFF, (data >> 16) & 0xFF,
-			 (data >> 8) & 0xFF, data & 0xFF) < 0)
-		return;
-	while (!req.complete)
-		cuda_poll();
-}
-
 static __u8 cuda_read_pram(int offset)
 {
 	struct adb_request req;
@@ -91,33 +62,6 @@ static void cuda_write_pram(int offset, __u8 data)
 #endif /* CONFIG_ADB_CUDA */
 
 #ifdef CONFIG_ADB_PMU
-static time64_t pmu_read_time(void)
-{
-	struct adb_request req;
-	time64_t time;
-
-	if (pmu_request(&req, NULL, 1, PMU_READ_RTC) < 0)
-		return 0;
-	pmu_wait_complete(&req);
-
-	time = (u32)((req.reply[0] << 24) | (req.reply[1] << 16) |
-		     (req.reply[2] << 8) | req.reply[3]);
-
-	return time - RTC_OFFSET;
-}
-
-static void pmu_write_time(time64_t time)
-{
-	struct adb_request req;
-	u32 data = lower_32_bits(time + RTC_OFFSET);
-
-	if (pmu_request(&req, NULL, 5, PMU_SET_RTC,
-			(data >> 24) & 0xFF, (data >> 16) & 0xFF,
-			(data >> 8) & 0xFF, data & 0xFF) < 0)
-		return;
-	pmu_wait_complete(&req);
-}
-
 static __u8 pmu_read_pram(int offset)
 {
 	struct adb_request req;
@@ -295,13 +239,17 @@ static time64_t via_read_time(void)
  * is basically any machine with Mac II-style ADB.
  */
 
-static void via_write_time(time64_t time)
+static void via_set_rtc_time(struct rtc_time *tm)
 {
 	union {
 		__u8 cdata[4];
 		__u32 idata;
 	} data;
 	__u8 temp;
+	time64_t time;
+
+	time = mktime64(tm->tm_year + 1900, tm->tm_mon + 1, tm->tm_mday,
+	                tm->tm_hour, tm->tm_min, tm->tm_sec);
 
 	/* Clear the write protect bit */
 
@@ -641,12 +589,12 @@ int mac_hwclk(int op, struct rtc_time *t)
 #ifdef CONFIG_ADB_CUDA
 		case MAC_ADB_EGRET:
 		case MAC_ADB_CUDA:
-			now = cuda_read_time();
+			now = cuda_get_time();
 			break;
 #endif
 #ifdef CONFIG_ADB_PMU
 		case MAC_ADB_PB2:
-			now = pmu_read_time();
+			now = pmu_get_time();
 			break;
 #endif
 		default:
@@ -665,24 +613,21 @@ int mac_hwclk(int op, struct rtc_time *t)
 		         __func__, t->tm_year + 1900, t->tm_mon + 1, t->tm_mday,
 		         t->tm_hour, t->tm_min, t->tm_sec);
 
-		now = mktime64(t->tm_year + 1900, t->tm_mon + 1, t->tm_mday,
-			       t->tm_hour, t->tm_min, t->tm_sec);
-
 		switch (macintosh_config->adb_type) {
 		case MAC_ADB_IOP:
 		case MAC_ADB_II:
 		case MAC_ADB_PB1:
-			via_write_time(now);
+			via_set_rtc_time(t);
 			break;
 #ifdef CONFIG_ADB_CUDA
 		case MAC_ADB_EGRET:
 		case MAC_ADB_CUDA:
-			cuda_write_time(now);
+			cuda_set_rtc_time(t);
 			break;
 #endif
 #ifdef CONFIG_ADB_PMU
 		case MAC_ADB_PB2:
-			pmu_write_time(now);
+			pmu_set_rtc_time(t);
 			break;
 #endif
 		default:
diff --git a/arch/powerpc/platforms/powermac/time.c b/arch/powerpc/platforms/powermac/time.c
index f92c1918fb56..f157e3d071f2 100644
--- a/arch/powerpc/platforms/powermac/time.c
+++ b/arch/powerpc/platforms/powermac/time.c
@@ -44,13 +44,6 @@
 #define DBG(x...)
 #endif
 
-/*
- * Offset between Unix time (1970-based) and Mac time (1904-based). Cuda and PMU
- * times wrap in 2040. If we need to handle later times, the read_time functions
- * need to be changed to interpret wrapped times as post-2040.
- */
-#define RTC_OFFSET	2082844800
-
 /*
  * Calibrate the decrementer frequency with the VIA timer 1.
  */
@@ -90,98 +83,6 @@ long __init pmac_time_init(void)
 	return delta;
 }
 
-#ifdef CONFIG_ADB_CUDA
-static time64_t cuda_get_time(void)
-{
-	struct adb_request req;
-	time64_t now;
-
-	if (cuda_request(&req, NULL, 2, CUDA_PACKET, CUDA_GET_TIME) < 0)
-		return 0;
-	while (!req.complete)
-		cuda_poll();
-	if (req.reply_len != 7)
-		printk(KERN_ERR "cuda_get_time: got %d byte reply\n",
-		       req.reply_len);
-	now = (u32)((req.reply[3] << 24) + (req.reply[4] << 16) +
-		    (req.reply[5] << 8) + req.reply[6]);
-	/* it's either after year 2040, or the RTC has gone backwards */
-	WARN_ON(now < RTC_OFFSET);
-
-	return now - RTC_OFFSET;
-}
-
-#define cuda_get_rtc_time(tm)	rtc_time64_to_tm(cuda_get_time(), (tm))
-
-static int cuda_set_rtc_time(struct rtc_time *tm)
-{
-	u32 nowtime;
-	struct adb_request req;
-
-	nowtime = lower_32_bits(rtc_tm_to_time64(tm) + RTC_OFFSET);
-	if (cuda_request(&req, NULL, 6, CUDA_PACKET, CUDA_SET_TIME,
-			 nowtime >> 24, nowtime >> 16, nowtime >> 8,
-			 nowtime) < 0)
-		return -ENXIO;
-	while (!req.complete)
-		cuda_poll();
-	if ((req.reply_len != 3) && (req.reply_len != 7))
-		printk(KERN_ERR "cuda_set_rtc_time: got %d byte reply\n",
-		       req.reply_len);
-	return 0;
-}
-
-#else
-#define cuda_get_time()		0
-#define cuda_get_rtc_time(tm)
-#define cuda_set_rtc_time(tm)	0
-#endif
-
-#ifdef CONFIG_ADB_PMU
-static time64_t pmu_get_time(void)
-{
-	struct adb_request req;
-	time64_t now;
-
-	if (pmu_request(&req, NULL, 1, PMU_READ_RTC) < 0)
-		return 0;
-	pmu_wait_complete(&req);
-	if (req.reply_len != 4)
-		printk(KERN_ERR "pmu_get_time: got %d byte reply from PMU\n",
-		       req.reply_len);
-	now = (u32)((req.reply[0] << 24) + (req.reply[1] << 16)	+
-		    (req.reply[2] << 8) + req.reply[3]);
-
-	/* it's either after year 2040, or the RTC has gone backwards */
-	WARN_ON(now < RTC_OFFSET);
-
-	return now - RTC_OFFSET;
-}
-
-#define pmu_get_rtc_time(tm)	rtc_time64_to_tm(pmu_get_time(), (tm))
-
-static int pmu_set_rtc_time(struct rtc_time *tm)
-{
-	u32 nowtime;
-	struct adb_request req;
-
-	nowtime = lower_32_bits(rtc_tm_to_time64(tm) + RTC_OFFSET);
-	if (pmu_request(&req, NULL, 5, PMU_SET_RTC, nowtime >> 24,
-			nowtime >> 16, nowtime >> 8, nowtime) < 0)
-		return -ENXIO;
-	pmu_wait_complete(&req);
-	if (req.reply_len != 0)
-		printk(KERN_ERR "pmu_set_rtc_time: %d byte reply from PMU\n",
-		       req.reply_len);
-	return 0;
-}
-
-#else
-#define pmu_get_time()		0
-#define pmu_get_rtc_time(tm)
-#define pmu_set_rtc_time(tm)	0
-#endif
-
 #ifdef CONFIG_PMAC_SMU
 static time64_t smu_get_time(void)
 {
@@ -191,11 +92,6 @@ static time64_t smu_get_time(void)
 		return 0;
 	return rtc_tm_to_time64(&tm);
 }
-
-#else
-#define smu_get_time()			0
-#define smu_get_rtc_time(tm, spin)
-#define smu_set_rtc_time(tm, spin)	0
 #endif
 
 /* Can't be __init, it's called when suspending and resuming */
@@ -203,12 +99,18 @@ time64_t pmac_get_boot_time(void)
 {
 	/* Get the time from the RTC, used only at boot time */
 	switch (sys_ctrler) {
+#ifdef CONFIG_ADB_CUDA
 	case SYS_CTRLER_CUDA:
 		return cuda_get_time();
+#endif
+#ifdef CONFIG_ADB_PMU
 	case SYS_CTRLER_PMU:
 		return pmu_get_time();
+#endif
+#ifdef CONFIG_PMAC_SMU
 	case SYS_CTRLER_SMU:
 		return smu_get_time();
+#endif
 	default:
 		return 0;
 	}
@@ -218,15 +120,21 @@ void pmac_get_rtc_time(struct rtc_time *tm)
 {
 	/* Get the time from the RTC, used only at boot time */
 	switch (sys_ctrler) {
+#ifdef CONFIG_ADB_CUDA
 	case SYS_CTRLER_CUDA:
-		cuda_get_rtc_time(tm);
+		rtc_time64_to_tm(cuda_get_time(), tm);
 		break;
+#endif
+#ifdef CONFIG_ADB_PMU
 	case SYS_CTRLER_PMU:
-		pmu_get_rtc_time(tm);
+		rtc_time64_to_tm(pmu_get_time(), tm);
 		break;
+#endif
+#ifdef CONFIG_PMAC_SMU
 	case SYS_CTRLER_SMU:
 		smu_get_rtc_time(tm, 1);
 		break;
+#endif
 	default:
 		;
 	}
@@ -235,12 +143,18 @@ void pmac_get_rtc_time(struct rtc_time *tm)
 int pmac_set_rtc_time(struct rtc_time *tm)
 {
 	switch (sys_ctrler) {
+#ifdef CONFIG_ADB_CUDA
 	case SYS_CTRLER_CUDA:
 		return cuda_set_rtc_time(tm);
+#endif
+#ifdef CONFIG_ADB_PMU
 	case SYS_CTRLER_PMU:
 		return pmu_set_rtc_time(tm);
+#endif
+#ifdef CONFIG_PMAC_SMU
 	case SYS_CTRLER_SMU:
 		return smu_set_rtc_time(tm, 1);
+#endif
 	default:
 		return -ENODEV;
 	}
diff --git a/drivers/macintosh/via-cuda.c b/drivers/macintosh/via-cuda.c
index 98dd702eb867..bbec6ac0a966 100644
--- a/drivers/macintosh/via-cuda.c
+++ b/drivers/macintosh/via-cuda.c
@@ -766,3 +766,38 @@ cuda_input(unsigned char *buf, int nb)
 	               buf, nb, false);
     }
 }
+
+/* Offset between Unix time (1970-based) and Mac time (1904-based) */
+#define RTC_OFFSET	2082844800
+
+time64_t cuda_get_time(void)
+{
+	struct adb_request req;
+	u32 now;
+
+	if (cuda_request(&req, NULL, 2, CUDA_PACKET, CUDA_GET_TIME) < 0)
+		return 0;
+	while (!req.complete)
+		cuda_poll();
+	if (req.reply_len != 7)
+		pr_err("%s: got %d byte reply\n", __func__, req.reply_len);
+	now = (req.reply[3] << 24) + (req.reply[4] << 16) +
+	      (req.reply[5] << 8) + req.reply[6];
+	return (time64_t)now - RTC_OFFSET;
+}
+
+int cuda_set_rtc_time(struct rtc_time *tm)
+{
+	u32 now;
+	struct adb_request req;
+
+	now = lower_32_bits(rtc_tm_to_time64(tm) + RTC_OFFSET);
+	if (cuda_request(&req, NULL, 6, CUDA_PACKET, CUDA_SET_TIME,
+	                 now >> 24, now >> 16, now >> 8, now) < 0)
+		return -ENXIO;
+	while (!req.complete)
+		cuda_poll();
+	if ((req.reply_len != 3) && (req.reply_len != 7))
+		pr_err("%s: got %d byte reply\n", __func__, req.reply_len);
+	return 0;
+}
diff --git a/drivers/macintosh/via-pmu.c b/drivers/macintosh/via-pmu.c
index d72c450aebe5..60f57e2abf21 100644
--- a/drivers/macintosh/via-pmu.c
+++ b/drivers/macintosh/via-pmu.c
@@ -1737,6 +1737,39 @@ pmu_enable_irled(int on)
 	pmu_wait_complete(&req);
 }
 
+/* Offset between Unix time (1970-based) and Mac time (1904-based) */
+#define RTC_OFFSET	2082844800
+
+time64_t pmu_get_time(void)
+{
+	struct adb_request req;
+	u32 now;
+
+	if (pmu_request(&req, NULL, 1, PMU_READ_RTC) < 0)
+		return 0;
+	pmu_wait_complete(&req);
+	if (req.reply_len != 4)
+		pr_err("%s: got %d byte reply\n", __func__, req.reply_len);
+	now = (req.reply[0] << 24) + (req.reply[1] << 16) +
+	      (req.reply[2] << 8) + req.reply[3];
+	return (time64_t)now - RTC_OFFSET;
+}
+
+int pmu_set_rtc_time(struct rtc_time *tm)
+{
+	u32 now;
+	struct adb_request req;
+
+	now = lower_32_bits(rtc_tm_to_time64(tm) + RTC_OFFSET);
+	if (pmu_request(&req, NULL, 5, PMU_SET_RTC,
+	                now >> 24, now >> 16, now >> 8, now) < 0)
+		return -ENXIO;
+	pmu_wait_complete(&req);
+	if (req.reply_len != 0)
+		pr_err("%s: got %d byte reply\n", __func__, req.reply_len);
+	return 0;
+}
+
 void
 pmu_restart(void)
 {
diff --git a/include/linux/cuda.h b/include/linux/cuda.h
index 056867f09a01..45bfe9d61271 100644
--- a/include/linux/cuda.h
+++ b/include/linux/cuda.h
@@ -8,6 +8,7 @@
 #ifndef _LINUX_CUDA_H
 #define _LINUX_CUDA_H
 
+#include <linux/rtc.h>
 #include <uapi/linux/cuda.h>
 
 
@@ -16,4 +17,7 @@ extern int cuda_request(struct adb_request *req,
 			void (*done)(struct adb_request *), int nbytes, ...);
 extern void cuda_poll(void);
 
+extern time64_t cuda_get_time(void);
+extern int cuda_set_rtc_time(struct rtc_time *tm);
+
 #endif /* _LINUX_CUDA_H */
diff --git a/include/linux/pmu.h b/include/linux/pmu.h
index 9ac8fc60ad49..52453a24a24f 100644
--- a/include/linux/pmu.h
+++ b/include/linux/pmu.h
@@ -9,6 +9,7 @@
 #ifndef _LINUX_PMU_H
 #define _LINUX_PMU_H
 
+#include <linux/rtc.h>
 #include <uapi/linux/pmu.h>
 
 
@@ -36,6 +37,9 @@ static inline void pmu_resume(void)
 
 extern void pmu_enable_irled(int on);
 
+extern time64_t pmu_get_time(void);
+extern int pmu_set_rtc_time(struct rtc_time *tm);
+
 extern void pmu_restart(void);
 extern void pmu_shutdown(void);
 extern void pmu_unlock(void);
-- 
2.16.4

[PATCH 2/7] macintosh/adb: Rework printk output again

[Finn Thain]

Avoid the KERN_CONT problem by avoiding message fragments. The problem
arises during async ADB bus probing, when ADB messages may get mixed up
with other messages. See also, commit 4bcc595ccd80 ("printk: reinstate
KERN_CONT for printing continuation lines").

Remove a number of printk() continuation lines by logging handler
changes in adb_try_handler_change() instead.

This patch addresses the problematic use of "\n" at the beginning of
pr_cont() messages, which got overlooked in commit f2be6295684b
("macintosh/adb: Properly mark continued kernel messages").

That commit also changed printk(KERN_DEBUG ...) to pr_debug(...), which
hinders work on low-level ADB driver bugs. Revert that change.

Cc: Andreas Schwab <schwab@linux-m68k.org>
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
---
 drivers/macintosh/adb.c    |  8 ++++---
 drivers/macintosh/adbhid.c | 53 ++++++++++++++++++----------------------------
 2 files changed, 26 insertions(+), 35 deletions(-)

diff --git a/drivers/macintosh/adb.c b/drivers/macintosh/adb.c
index 76e98f0f7a3e..e49d1f287a17 100644
--- a/drivers/macintosh/adb.c
+++ b/drivers/macintosh/adb.c
@@ -203,15 +203,15 @@ static int adb_scan_bus(void)
 	}
 
 	/* Now fill in the handler_id field of the adb_handler entries. */
-	pr_debug("adb devices:\n");
 	for (i = 1; i < 16; i++) {
 		if (adb_handler[i].original_address == 0)
 			continue;
 		adb_request(&req, NULL, ADBREQ_SYNC | ADBREQ_REPLY, 1,
 			    (i << 4) | 0xf);
 		adb_handler[i].handler_id = req.reply[2];
-		pr_debug(" [%d]: %d %x\n", i, adb_handler[i].original_address,
-			 adb_handler[i].handler_id);
+		printk(KERN_DEBUG "adb device [%d]: %d 0x%X\n", i,
+		       adb_handler[i].original_address,
+		       adb_handler[i].handler_id);
 		devmask |= 1 << i;
 	}
 	return devmask;
@@ -579,6 +579,8 @@ adb_try_handler_change(int address, int new_id)
 	mutex_lock(&adb_handler_mutex);
 	ret = try_handler_change(address, new_id);
 	mutex_unlock(&adb_handler_mutex);
+	if (ret)
+		pr_debug("adb handler change: [%d] 0x%X\n", address, new_id);
 	return ret;
 }
 EXPORT_SYMBOL(adb_try_handler_change);
diff --git a/drivers/macintosh/adbhid.c b/drivers/macintosh/adbhid.c
index a261892c03b3..75482eeab2c4 100644
--- a/drivers/macintosh/adbhid.c
+++ b/drivers/macintosh/adbhid.c
@@ -757,6 +757,7 @@ adbhid_input_register(int id, int default_id, int original_handler_id,
 	struct input_dev *input_dev;
 	int err;
 	int i;
+	char *keyboard_type;
 
 	if (adbhid[id]) {
 		pr_err("Trying to reregister ADB HID on ID %d\n", id);
@@ -798,24 +799,23 @@ adbhid_input_register(int id, int default_id, int original_handler_id,
 
 		memcpy(hid->keycode, adb_to_linux_keycodes, sizeof(adb_to_linux_keycodes));
 
-		pr_info("Detected ADB keyboard, type ");
 		switch (original_handler_id) {
 		default:
-			pr_cont("<unknown>.\n");
+			keyboard_type = "<unknown>";
 			input_dev->id.version = ADB_KEYBOARD_UNKNOWN;
 			break;
 
 		case 0x01: case 0x02: case 0x03: case 0x06: case 0x08:
 		case 0x0C: case 0x10: case 0x18: case 0x1B: case 0x1C:
 		case 0xC0: case 0xC3: case 0xC6:
-			pr_cont("ANSI.\n");
+			keyboard_type = "ANSI";
 			input_dev->id.version = ADB_KEYBOARD_ANSI;
 			break;
 
 		case 0x04: case 0x05: case 0x07: case 0x09: case 0x0D:
 		case 0x11: case 0x14: case 0x19: case 0x1D: case 0xC1:
 		case 0xC4: case 0xC7:
-			pr_cont("ISO, swapping keys.\n");
+			keyboard_type = "ISO, swapping keys";
 			input_dev->id.version = ADB_KEYBOARD_ISO;
 			i = hid->keycode[10];
 			hid->keycode[10] = hid->keycode[50];
@@ -824,10 +824,11 @@ adbhid_input_register(int id, int default_id, int original_handler_id,
 
 		case 0x12: case 0x15: case 0x16: case 0x17: case 0x1A:
 		case 0x1E: case 0xC2: case 0xC5: case 0xC8: case 0xC9:
-			pr_cont("JIS.\n");
+			keyboard_type = "JIS";
 			input_dev->id.version = ADB_KEYBOARD_JIS;
 			break;
 		}
+		pr_info("Detected ADB keyboard, type %s.\n", keyboard_type);
 
 		for (i = 0; i < 128; i++)
 			if (hid->keycode[i])
@@ -972,16 +973,13 @@ adbhid_probe(void)
 		   ->get it to send separate codes for left and right shift,
 		   control, option keys */
 #if 0		/* handler 5 doesn't send separate codes for R modifiers */
-		if (adb_try_handler_change(id, 5))
-			printk("ADB keyboard at %d, handler set to 5\n", id);
-		else
+		if (!adb_try_handler_change(id, 5))
 #endif
-		if (adb_try_handler_change(id, 3))
-			printk("ADB keyboard at %d, handler set to 3\n", id);
-		else
-			printk("ADB keyboard at %d, handler 1\n", id);
+		adb_try_handler_change(id, 3);
 
 		adb_get_infos(id, &default_id, &cur_handler_id);
+		printk(KERN_DEBUG "ADB keyboard at %d has handler 0x%X\n",
+		       id, cur_handler_id);
 		reg |= adbhid_input_reregister(id, default_id, org_handler_id,
 					       cur_handler_id, 0);
 	}
@@ -999,48 +997,44 @@ adbhid_probe(void)
 	for (i = 0; i < mouse_ids.nids; i++) {
 		int id = mouse_ids.id[i];
 		int mouse_kind;
+		char *desc = "standard";
 
 		adb_get_infos(id, &default_id, &org_handler_id);
 
 		if (adb_try_handler_change(id, 4)) {
-			printk("ADB mouse at %d, handler set to 4", id);
 			mouse_kind = ADBMOUSE_EXTENDED;
 		}
 		else if (adb_try_handler_change(id, 0x2F)) {
-			printk("ADB mouse at %d, handler set to 0x2F", id);
 			mouse_kind = ADBMOUSE_MICROSPEED;
 		}
 		else if (adb_try_handler_change(id, 0x42)) {
-			printk("ADB mouse at %d, handler set to 0x42", id);
 			mouse_kind = ADBMOUSE_TRACKBALLPRO;
 		}
 		else if (adb_try_handler_change(id, 0x66)) {
-			printk("ADB mouse at %d, handler set to 0x66", id);
 			mouse_kind = ADBMOUSE_MICROSPEED;
 		}
 		else if (adb_try_handler_change(id, 0x5F)) {
-			printk("ADB mouse at %d, handler set to 0x5F", id);
 			mouse_kind = ADBMOUSE_MICROSPEED;
 		}
 		else if (adb_try_handler_change(id, 3)) {
-			printk("ADB mouse at %d, handler set to 3", id);
 			mouse_kind = ADBMOUSE_MS_A3;
 		}
 		else if (adb_try_handler_change(id, 2)) {
-			printk("ADB mouse at %d, handler set to 2", id);
 			mouse_kind = ADBMOUSE_STANDARD_200;
 		}
 		else {
-			printk("ADB mouse at %d, handler 1", id);
 			mouse_kind = ADBMOUSE_STANDARD_100;
 		}
 
 		if ((mouse_kind == ADBMOUSE_TRACKBALLPRO)
 		    || (mouse_kind == ADBMOUSE_MICROSPEED)) {
+			desc = "Microspeed/MacPoint or compatible";
 			init_microspeed(id);
 		} else if (mouse_kind == ADBMOUSE_MS_A3) {
+			desc = "Mouse Systems A3 Mouse or compatible";
 			init_ms_a3(id);
 		} else if (mouse_kind ==  ADBMOUSE_EXTENDED) {
+			desc = "extended";
 			/*
 			 * Register 1 is usually used for device
 			 * identification.  Here, we try to identify
@@ -1054,32 +1048,36 @@ adbhid_probe(void)
 			    (req.reply[1] == 0x9a) && ((req.reply[2] == 0x21)
 			    	|| (req.reply[2] == 0x20))) {
 				mouse_kind = ADBMOUSE_TRACKBALL;
+				desc = "trackman/mouseman";
 				init_trackball(id);
 			}
 			else if ((req.reply_len >= 4) &&
 			    (req.reply[1] == 0x74) && (req.reply[2] == 0x70) &&
 			    (req.reply[3] == 0x61) && (req.reply[4] == 0x64)) {
 				mouse_kind = ADBMOUSE_TRACKPAD;
+				desc = "trackpad";
 				init_trackpad(id);
 			}
 			else if ((req.reply_len >= 4) &&
 			    (req.reply[1] == 0x4b) && (req.reply[2] == 0x4d) &&
 			    (req.reply[3] == 0x4c) && (req.reply[4] == 0x31)) {
 				mouse_kind = ADBMOUSE_TURBOMOUSE5;
+				desc = "TurboMouse 5";
 				init_turbomouse(id);
 			}
 			else if ((req.reply_len == 9) &&
 			    (req.reply[1] == 0x4b) && (req.reply[2] == 0x4f) &&
 			    (req.reply[3] == 0x49) && (req.reply[4] == 0x54)) {
 				if (adb_try_handler_change(id, 0x42)) {
-					pr_cont("\nADB MacAlly 2-button mouse at %d, handler set to 0x42", id);
 					mouse_kind = ADBMOUSE_MACALLY2;
+					desc = "MacAlly 2-button";
 				}
 			}
 		}
-		pr_cont("\n");
 
 		adb_get_infos(id, &default_id, &cur_handler_id);
+		printk(KERN_DEBUG "ADB mouse (%s) at %d has handler 0x%X\n",
+		       desc, id, cur_handler_id);
 		reg |= adbhid_input_reregister(id, default_id, org_handler_id,
 					       cur_handler_id, mouse_kind);
 	}
@@ -1092,12 +1090,10 @@ init_trackpad(int id)
 	struct adb_request req;
 	unsigned char r1_buffer[8];
 
-	pr_cont(" (trackpad)");
-
 	adb_request(&req, NULL, ADBREQ_SYNC | ADBREQ_REPLY, 1,
 		    ADB_READREG(id,1));
 	if (req.reply_len < 8)
-	    pr_cont("bad length for reg. 1\n");
+		pr_err("%s: bad length for reg. 1\n", __func__);
 	else
 	{
 	    memcpy(r1_buffer, &req.reply[1], 8);
@@ -1145,8 +1141,6 @@ init_trackball(int id)
 {
 	struct adb_request req;
 
-	pr_cont(" (trackman/mouseman)");
-
 	adb_request(&req, NULL, ADBREQ_SYNC, 3,
 	ADB_WRITEREG(id,1), 00,0x81);
 
@@ -1177,8 +1171,6 @@ init_turbomouse(int id)
 {
 	struct adb_request req;
 
-	pr_cont(" (TurboMouse 5)");
-
 	adb_request(&req, NULL, ADBREQ_SYNC, 1, ADB_FLUSH(id));
 
 	adb_request(&req, NULL, ADBREQ_SYNC, 1, ADB_FLUSH(3));
@@ -1213,8 +1205,6 @@ init_microspeed(int id)
 {
 	struct adb_request req;
 
-	pr_cont(" (Microspeed/MacPoint or compatible)");
-
 	adb_request(&req, NULL, ADBREQ_SYNC, 1, ADB_FLUSH(id));
 
 	/* This will initialize mice using the Microspeed, MacPoint and
@@ -1253,7 +1243,6 @@ init_ms_a3(int id)
 {
 	struct adb_request req;
 
-	pr_cont(" (Mouse Systems A3 Mouse, or compatible)");
 	adb_request(&req, NULL, ADBREQ_SYNC, 3,
 	ADB_WRITEREG(id, 0x2),
 	    0x00,
-- 
2.16.4

[PATCH 4/7] macintosh/via-macii: Remove BUG_ON assertions

[Finn Thain]

The BUG_ON assertions I added to the via-macii driver over a decade ago
haven't fired AFAIK. Some can never fire (by inspection). One assertion
checks for a NULL pointer, but that would merely substitute a BUG crash
for an Oops crash. Remove the pointless BUG_ON assertions and replace
the others with a WARN_ON and an array bounds check.

Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
---
 drivers/macintosh/via-macii.c | 49 +++++++------------------------------------
 1 file changed, 7 insertions(+), 42 deletions(-)

diff --git a/drivers/macintosh/via-macii.c b/drivers/macintosh/via-macii.c
index 36a4f49e79b5..7e0e32fa7eb2 100644
--- a/drivers/macintosh/via-macii.c
+++ b/drivers/macintosh/via-macii.c
@@ -120,23 +120,6 @@ static int srq_asserted;     /* have to poll for the device that asserted it */
 static int command_byte;         /* the most recent command byte transmitted */
 static int autopoll_devs;      /* bits set are device addresses to be polled */
 
-/* Sanity check for request queue. Doesn't check for cycles. */
-static int request_is_queued(struct adb_request *req) {
-	struct adb_request *cur;
-	unsigned long flags;
-	local_irq_save(flags);
-	cur = current_req;
-	while (cur) {
-		if (cur == req) {
-			local_irq_restore(flags);
-			return 1;
-		}
-		cur = cur->next;
-	}
-	local_irq_restore(flags);
-	return 0;
-}
-
 /* Check for MacII style ADB */
 static int macii_probe(void)
 {
@@ -213,8 +196,6 @@ static void macii_queue_poll(void)
 	else
 		next_device = ffs(autopoll_devs) - 1;
 
-	BUG_ON(request_is_queued(&req));
-
 	adb_request(&req, NULL, ADBREQ_NOSEND, 1,
 	            ADB_READREG(next_device, 0));
 
@@ -237,18 +218,13 @@ static int macii_send_request(struct adb_request *req, int sync)
 	int err;
 	unsigned long flags;
 
-	BUG_ON(request_is_queued(req));
-
 	local_irq_save(flags);
 	err = macii_write(req);
 	local_irq_restore(flags);
 
-	if (!err && sync) {
-		while (!req->complete) {
+	if (!err && sync)
+		while (!req->complete)
 			macii_poll();
-		}
-		BUG_ON(request_is_queued(req));
-	}
 
 	return err;
 }
@@ -327,9 +303,6 @@ static int macii_reset_bus(void)
 {
 	static struct adb_request req;
 	
-	if (request_is_queued(&req))
-		return 0;
-
 	/* Command = 0, Address = ignored */
 	adb_request(&req, NULL, ADBREQ_NOSEND, 1, ADB_BUSRESET);
 	macii_send_request(&req, 1);
@@ -347,10 +320,6 @@ static void macii_start(void)
 
 	req = current_req;
 
-	BUG_ON(req == NULL);
-
-	BUG_ON(macii_state != idle);
-
 	/* Now send it. Be careful though, that first byte of the request
 	 * is actually ADB_PACKET; the real data begins at index 1!
 	 * And req->nbytes is the number of bytes of real data plus one.
@@ -388,7 +357,6 @@ static void macii_start(void)
 static irqreturn_t macii_interrupt(int irq, void *arg)
 {
 	int x;
-	static int entered;
 	struct adb_request *req;
 
 	if (!arg) {
@@ -399,8 +367,6 @@ static irqreturn_t macii_interrupt(int irq, void *arg)
 			return IRQ_NONE;
 	}
 
-	BUG_ON(entered++);
-
 	last_status = status;
 	status = via[B] & (ST_MASK|CTLR_IRQ);
 
@@ -409,7 +375,7 @@ static irqreturn_t macii_interrupt(int irq, void *arg)
 			if (reading_reply) {
 				reply_ptr = current_req->reply;
 			} else {
-				BUG_ON(current_req != NULL);
+				WARN_ON(current_req);
 				reply_ptr = reply_buf;
 			}
 
@@ -474,8 +440,8 @@ static irqreturn_t macii_interrupt(int irq, void *arg)
 
 		case reading:
 			x = via[SR];
-			BUG_ON((status & ST_MASK) == ST_CMD ||
-			       (status & ST_MASK) == ST_IDLE);
+			WARN_ON((status & ST_MASK) == ST_CMD ||
+				(status & ST_MASK) == ST_IDLE);
 
 			/* Bus timeout with SRQ sequence:
 			 *     data is "XX FF"      while CTLR_IRQ is "L L"
@@ -502,8 +468,8 @@ static irqreturn_t macii_interrupt(int irq, void *arg)
 				}
 			}
 
-			if (macii_state == reading) {
-				BUG_ON(reply_len > 15);
+			if (macii_state == reading &&
+			    reply_len < ARRAY_SIZE(reply_buf)) {
 				reply_ptr++;
 				*reply_ptr = x;
 				reply_len++;
@@ -546,6 +512,5 @@ static irqreturn_t macii_interrupt(int irq, void *arg)
 		break;
 	}
 
-	entered--;
 	return IRQ_HANDLED;
 }
-- 
2.16.4

[PATCH 6/7] macintosh/via-macii, macintosh/adb-iop: Modernize printk calls

[Finn Thain]

Add missing severity level to log messages.

Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
---
 drivers/macintosh/adb-iop.c   | 2 +-
 drivers/macintosh/via-macii.c | 2 +-
 2 files changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/macintosh/adb-iop.c b/drivers/macintosh/adb-iop.c
index ca623e6446e4..3a1e995ecc0e 100644
--- a/drivers/macintosh/adb-iop.c
+++ b/drivers/macintosh/adb-iop.c
@@ -208,7 +208,7 @@ int adb_iop_probe(void)
 
 int adb_iop_init(void)
 {
-	printk("adb: IOP ISM driver v0.4 for Unified ADB.\n");
+	pr_info("adb: IOP ISM driver v0.4 for Unified ADB\n");
 	iop_listen(ADB_IOP, ADB_CHAN, adb_iop_listen, "ADB");
 	return 0;
 }
diff --git a/drivers/macintosh/via-macii.c b/drivers/macintosh/via-macii.c
index 6ed9ac91aca1..a38f57ba50cb 100644
--- a/drivers/macintosh/via-macii.c
+++ b/drivers/macintosh/via-macii.c
@@ -127,7 +127,7 @@ static int macii_probe(void)
 
 	via = via1;
 
-	printk("adb: Mac II ADB Driver v1.0 for Unified ADB\n");
+	pr_info("adb: Mac II ADB Driver v1.0 for Unified ADB\n");
 	return 0;
 }
 
-- 
2.16.4

[PATCH 5/7] macintosh/via-macii: Simplify locking

[Finn Thain]

Modifying the request queue or changing the current state requires
mutual exclusion. Use local_irq_disable() consistently for this
rather than disabling the ADB interrupt. This simplifies the locking
scheme and brings via-macii into line with the other ADB drivers.

Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
---
 drivers/macintosh/via-macii.c | 26 ++++++++++++++++++--------
 1 file changed, 18 insertions(+), 8 deletions(-)

diff --git a/drivers/macintosh/via-macii.c b/drivers/macintosh/via-macii.c
index 7e0e32fa7eb2..6ed9ac91aca1 100644
--- a/drivers/macintosh/via-macii.c
+++ b/drivers/macintosh/via-macii.c
@@ -216,22 +216,23 @@ static void macii_queue_poll(void)
 static int macii_send_request(struct adb_request *req, int sync)
 {
 	int err;
-	unsigned long flags;
 
-	local_irq_save(flags);
 	err = macii_write(req);
-	local_irq_restore(flags);
+	if (err)
+		return err;
 
-	if (!err && sync)
+	if (sync)
 		while (!req->complete)
 			macii_poll();
 
-	return err;
+	return 0;
 }
 
 /* Send an ADB request (append to request queue) */
 static int macii_write(struct adb_request *req)
 {
+	unsigned long flags;
+
 	if (req->nbytes < 2 || req->data[0] != ADB_PACKET || req->nbytes > 15) {
 		req->complete = 1;
 		return -EINVAL;
@@ -242,6 +243,8 @@ static int macii_write(struct adb_request *req)
 	req->complete = 0;
 	req->reply_len = 0;
 
+	local_irq_save(flags);
+
 	if (current_req != NULL) {
 		last_req->next = req;
 		last_req = req;
@@ -250,6 +253,9 @@ static int macii_write(struct adb_request *req)
 		last_req = req;
 		if (macii_state == idle) macii_start();
 	}
+
+	local_irq_restore(flags);
+
 	return 0;
 }
 
@@ -293,9 +299,7 @@ static inline int need_autopoll(void) {
 /* Prod the chip without interrupts */
 static void macii_poll(void)
 {
-	disable_irq(IRQ_MAC_ADB);
 	macii_interrupt(0, NULL);
-	enable_irq(IRQ_MAC_ADB);
 }
 
 /* Reset the bus */
@@ -358,13 +362,18 @@ static irqreturn_t macii_interrupt(int irq, void *arg)
 {
 	int x;
 	struct adb_request *req;
+	unsigned long flags;
+
+	local_irq_save(flags);
 
 	if (!arg) {
 		/* Clear the SR IRQ flag when polling. */
 		if (via[IFR] & SR_INT)
 			via[IFR] = SR_INT;
-		else
+		else {
+			local_irq_restore(flags);
 			return IRQ_NONE;
+		}
 	}
 
 	last_status = status;
@@ -512,5 +521,6 @@ static irqreturn_t macii_interrupt(int irq, void *arg)
 		break;
 	}
 
+	local_irq_restore(flags);
 	return IRQ_HANDLED;
 }
-- 
2.16.4

Re: [PATCH 1/7] macintosh: Use common code to access RTC

[Geert Uytterhoeven]

On Wed, Sep 12, 2018 at 2:18 AM Finn Thain <fthain@telegraphics.com.au> wrote:
> Now that the 68k Mac port has adopted the via-pmu driver, the same RTC
> code can be shared between m68k and powerpc. Replace duplicated code in
> arch/powerpc and arch/m68k with common RTC accessors for Cuda and PMU.
>
> Drop the problematic WARN_ON which was introduced in commit 22db552b50fa
> ("powerpc/powermac: Fix rtc read/write functions").
>
> Tested-by: Stan Johnson <userm57@yahoo.com>
> Signed-off-by: Finn Thain <fthain@telegraphics.com.au>

Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>

Gr{oetje,eeting}s,

                        Geert

-- 
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
                                -- Linus Torvalds

Re: [1/7] macintosh: Use common code to access RTC

[Michael Ellerman]

On Wed, 2018-09-12 at 00:18:44 UTC, Finn Thain wrote:
> Now that the 68k Mac port has adopted the via-pmu driver, the same RTC
> code can be shared between m68k and powerpc. Replace duplicated code in
> arch/powerpc and arch/m68k with common RTC accessors for Cuda and PMU.
> 
> Drop the problematic WARN_ON which was introduced in commit 22db552b50fa
> ("powerpc/powermac: Fix rtc read/write functions").
> 
> Tested-by: Stan Johnson <userm57@yahoo.com>
> Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
> Cc: Geert Uytterhoeven <geert@linux-m68k.org>
> Cc: Arnd Bergmann <arnd@arndb.de>
> Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>

Series applied to powerpc next, thanks.

https://git.kernel.org/powerpc/c/0792a2c8e0bbda3605b8d42c6b9635

cheers