linux-kernel.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Shawn Lin <shawn.lin@rock-chips.com>
To: "Christian Löhle" <CLoehle@hyperstone.com>
Cc: shawn.lin@rock-chips.com, "pali@kernel.org" <pali@kernel.org>,
	"huyue2@yulong.com" <huyue2@yulong.com>,
	"tiantao6@hisilicon.com" <tiantao6@hisilicon.com>,
	"linux-mmc@vger.kernel.org" <linux-mmc@vger.kernel.org>,
	"linux-kernel@vger.kernel.org" <linux-kernel@vger.kernel.org>,
	"ulf.hansson@linaro.org" <ulf.hansson@linaro.org>
Subject: Re: [PATCH] mmc: enable UHS voltage switch for SDSC if supported【请注意,邮件由linux-mmc-owner@vger.kernel.org代发】
Date: Fri, 23 Apr 2021 09:34:32 +0800	[thread overview]
Message-ID: <35677467-4ccd-9eae-3800-2bc7597cfa0f@rock-chips.com> (raw)
In-Reply-To: <CWXP265MB2680766F673A99D2F296B878C4469@CWXP265MB2680.GBRP265.PROD.OUTLOOK.COM>

On 2021/4/22 21:18, Christian Löhle wrote:
> Ignore the reported capacity if the card otherwise reports UHS support.
> 
> Currently SDSC cards reporting UHS support except for the CCS do not run
> through the voltage switch.
> While strictly speaking a SDSC card cannot support UHS in compliance
> with the standard, there is no good reason to throttle them that way.
> Especially for pSLCs in practice such cards benefit greatly by this patch,

Cduld you provide some more infomation about the SDSC cards which ones 
are labeled as UHS, e.g brand, webpage....

> as they can be new and UHS supporting, but must not lie about their CCS.
> The behaviour of linux-mmc for SDSC is deviating from the standard anyway
> in such a case, as the card is treated as UHS card not supporting the
> voltage switch in general.
> Such a card will come up as
> mmc0: new ultra high speed SDR25 SD card at address 0001.
> Thus the subsystem will support CMD23 and others to the card.
> But if we deviate from the standard anyway, then we might as well
> not throttle SDSC to 25MB/s.
> 
> Signed-off-by: Christian Loehle <cloehle@hyperstone.com>
> ---
>   drivers/mmc/core/sd.c | 7 +++----
>   1 file changed, 3 insertions(+), 4 deletions(-)
> 
> diff --git a/drivers/mmc/core/sd.c b/drivers/mmc/core/sd.c
> index 6fa51a6ed058..281ca2da8e0b 100644
> --- a/drivers/mmc/core/sd.c
> +++ b/drivers/mmc/core/sd.c
> @@ -841,11 +841,10 @@ int mmc_sd_get_cid(struct mmc_host *host, u32 ocr, u32 *cid, u32 *rocr)
>   		return err;
>   
>   	/*
> -	 * In case CCS and S18A in the response is set, start Signal Voltage
> -	 * Switch procedure. SPI mode doesn't support CMD11.
> +	 * In case S18A in the response is set, start Signal Voltage Switch
> +	 * procedure. SPI mode doesn't support CMD11.
>   	 */
> -	if (!mmc_host_is_spi(host) && rocr &&
> -	   ((*rocr & 0x41000000) == 0x41000000)) {
> +	if (!mmc_host_is_spi(host) && rocr && (*rocr & 0x01000000)) {
>   		err = mmc_set_uhs_voltage(host, pocr);
>   		if (err == -EAGAIN) {
>   			retries--;
> 



  reply	other threads:[~2021-04-23  1:42 UTC|newest]

Thread overview: 12+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2021-04-22 13:18 [PATCH] mmc: enable UHS voltage switch for SDSC if supported Christian Löhle
2021-04-23  1:34 ` Shawn Lin [this message]
2021-04-23  6:38   ` [PATCH] mmc: enable UHS voltage switch for SDSC if supported【请注意,邮件由linux-mmc-owner@vger.kernel.org代发】 Christian Löhle
2021-04-23  6:51     ` Shawn Lin
2021-04-30 10:45 ` [PATCH] mmc: enable UHS voltage switch for SDSC if supported Christian Löhle
2021-05-05 10:09 ` Ulf Hansson
2021-05-05 12:12   ` Christian Löhle
2021-05-05 14:20     ` Ulf Hansson
2021-05-06  8:34       ` Christian Löhle
2021-05-06 13:54         ` Ulf Hansson
2021-05-12 16:03 ` [PATCH v2] " Christian Löhle
2021-06-04 12:10   ` Ulf Hansson

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=35677467-4ccd-9eae-3800-2bc7597cfa0f@rock-chips.com \
    --to=shawn.lin@rock-chips.com \
    --cc=CLoehle@hyperstone.com \
    --cc=huyue2@yulong.com \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-mmc@vger.kernel.org \
    --cc=pali@kernel.org \
    --cc=tiantao6@hisilicon.com \
    --cc=ulf.hansson@linaro.org \
    --subject='Re: [PATCH] mmc: enable UHS voltage switch for SDSC if supported【请注意,邮件由linux-mmc-owner@vger.kernel.org代发】' \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).