[PATCH v2 0/2] Add device tree for Ampere's Mt. Mitchell BMC

[PATCH v2 0/2] Add device tree for Ampere's Mt. Mitchell BMC

[Quan Nguyen]

The Mt. Mitchell BMC is an ASPEED AST2600-based BMC for the Mt. Mitchell
hardware reference platform with AmpereOne(TM) processor.

v2 :
  + Add Ampere Mt. Mitchell BMC compatible                [Krzysztof]
  + Remove bootargs                                       [Krzysztof]
  + Fix gpio-keys nodes name to conform with device tree binding
  documents                                               [Krzysztof]
  + Fix some nodes to use generic name                    [Krzysztof]
  + Remove unnecessary blank line                         [Krzysztof]
  + Fix typo "LTC" to "LLC" in license info and corrected license
  info to GPL-2.0-only

Quan Nguyen (2):
  dt-bindings: arm: aspeed: document Ampere Mt.Mitchell BMC compatibles
  ARM: dts: aspeed: Add device tree for Ampere's Mt. Mitchell BMC

 .../bindings/arm/aspeed/aspeed.yaml           |   1 +
 arch/arm/boot/dts/Makefile                    |   1 +
 .../boot/dts/aspeed-bmc-ampere-mtmitchell.dts | 577 ++++++++++++++++++
 3 files changed, 579 insertions(+)
 create mode 100644 arch/arm/boot/dts/aspeed-bmc-ampere-mtmitchell.dts

-- 
2.35.1

[PATCH v2 1/2] dt-bindings: arm: aspeed: document Ampere Mt.Mitchell BMC compatibles

[Quan Nguyen]

Document Ampere Mt.Mitchell BMC board compatible.

Signed-off-by: Quan Nguyen <quan@os.amperecomputing.com>
---
v2:
  + Introduce in v2 to add Ampere Mt. Mitchell BMC compatible [Krzysztof]

 Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml b/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml
index d61408194998..b8146d5c4431 100644
--- a/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml
+++ b/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml
@@ -71,6 +71,7 @@ properties:
           - enum:
               - aspeed,ast2600-evb
               - aspeed,ast2600-evb-a1
+              - ampere,mtmitchell-bmc
               - facebook,bletchley-bmc
               - facebook,cloudripper-bmc
               - facebook,elbert-bmc
-- 
2.35.1

[PATCH v2 2/2] ARM: dts: aspeed: Add device tree for Ampere's Mt. Mitchell BMC

[Quan Nguyen]

The Mt. Mitchell BMC is an ASPEED AST2600-based BMC for the Mt. Mitchell
hardware reference platform with AmpereOne(TM) processor.

Signed-off-by: Quan Nguyen <quan@os.amperecomputing.com>
Signed-off-by: Phong Vo <phong@os.amperecomputing.com>
Signed-off-by: Thang Q. Nguyen <thang@os.amperecomputing.com>
---
v2 :
  + Remove bootargs                                       [Krzysztof]
  + Fix gpio-keys nodes name to conform with device tree binding
  documents                                               [Krzysztof]
  + Fix some nodes to use generic name                    [Krzysztof]
  + Remove unnecessary blank line                         [Krzysztof]
  + Fix typo "LTC" to "LLC" in license info and corrected license
  info to GPL-2.0-only

 arch/arm/boot/dts/Makefile                    |   1 +
 .../boot/dts/aspeed-bmc-ampere-mtmitchell.dts | 577 ++++++++++++++++++
 2 files changed, 578 insertions(+)
 create mode 100644 arch/arm/boot/dts/aspeed-bmc-ampere-mtmitchell.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index f9484f5ef126..ecb9dafb8f1a 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1573,6 +1573,7 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
 	aspeed-ast2600-evb.dtb \
 	aspeed-bmc-amd-ethanolx.dtb \
 	aspeed-bmc-ampere-mtjade.dtb \
+	aspeed-bmc-ampere-mtmitchell.dtb \
 	aspeed-bmc-arm-centriq2400-rep.dtb \
 	aspeed-bmc-arm-stardragon4800-rep2.dtb \
 	aspeed-bmc-asrock-e3c246d4i.dtb \
diff --git a/arch/arm/boot/dts/aspeed-bmc-ampere-mtmitchell.dts b/arch/arm/boot/dts/aspeed-bmc-ampere-mtmitchell.dts
new file mode 100644
index 000000000000..2e68f5264bb1
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed-bmc-ampere-mtmitchell.dts
@@ -0,0 +1,577 @@
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (c) 2022, Ampere Computing LLC
+
+/dts-v1/;
+
+#include "aspeed-g6.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+
+/ {
+	model = "Ampere Mt.Mitchell BMC";
+	compatible = "ampere,mtmitchell-bmc", "aspeed,ast2600";
+
+	chosen {
+		stdout-path = &uart5;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x80000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		gfx_memory: framebuffer {
+			size = <0x01000000>;
+			alignment = <0x01000000>;
+			compatible = "shared-dma-pool";
+			reusable;
+		};
+
+		video_engine_memory: video {
+			size = <0x04000000>;
+			alignment = <0x01000000>;
+			compatible = "shared-dma-pool";
+			reusable;
+		};
+
+		/* 1GB memory */
+		vga_memory: region@bf000000 {
+			no-map;
+			compatible = "shared-dma-pool";
+			reg = <0xbf000000 0x01000000>;  /* 16M */
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		s0-overtemp-event {
+			label = "S0_OVERTEMP";
+			gpios = <&gpio0 ASPEED_GPIO(V, 7) GPIO_ACTIVE_LOW>;
+			linux,code = <ASPEED_GPIO(V, 7)>;
+		};
+
+		s0-hightemp-event {
+			label = "S0_HIGHTEMP";
+			gpios = <&gpio0 ASPEED_GPIO(V, 0) GPIO_ACTIVE_LOW>;
+			linux,code = <ASPEED_GPIO(V, 0)>;
+		};
+
+		s1-overtemp-event {
+			label = "S1_OVERTEMP";
+			gpios = <&gpio0 ASPEED_GPIO(X, 6) GPIO_ACTIVE_LOW>;
+			linux,code = <ASPEED_GPIO(X, 6)>;
+		};
+
+		s1-hightemp-event {
+			label = "S1_HIGHTEMP";
+			gpios = <&gpio0 ASPEED_GPIO(X, 3) GPIO_ACTIVE_LOW>;
+			linux,code = <ASPEED_GPIO(X, 3)>;
+		};
+	};
+
+	voltage_mon_reg: voltage-mon-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "ltc2497_reg";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	gpioI5mux: mux-controller {
+		compatible = "gpio-mux";
+		#mux-control-cells = <0>;
+		mux-gpios = <&gpio0 ASPEED_GPIO(I, 5) GPIO_ACTIVE_HIGH>;
+	};
+
+	adc0mux: adc0mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc0 0>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc1mux: adc1mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc0 1>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc2mux: adc2mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc0 2>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc3mux: adc3mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc0 3>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc4mux: adc4mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc0 4>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc5mux: adc5mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc0 5>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc6mux: adc6mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc0 6>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc7mux: adc7mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc0 7>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc8mux: adc8mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc1 0>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc9mux: adc9mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc1 1>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc10mux: adc10mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc1 2>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc11mux: adc11mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc1 3>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc12mux: adc12mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc1 4>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc13mux: adc13mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc1 5>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc14mux: adc14mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc1 6>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc15mux: adc15mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc1 7>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc0mux 0>, <&adc0mux 1>,
+			<&adc1mux 0>, <&adc1mux 1>,
+			<&adc2mux 0>, <&adc2mux 1>,
+			<&adc3mux 0>, <&adc3mux 1>,
+			<&adc4mux 0>, <&adc4mux 1>,
+			<&adc5mux 0>, <&adc5mux 1>,
+			<&adc6mux 0>, <&adc6mux 1>,
+			<&adc7mux 0>, <&adc7mux 1>,
+			<&adc8mux 0>, <&adc8mux 1>,
+			<&adc9mux 0>, <&adc9mux 1>,
+			<&adc10mux 0>, <&adc10mux 1>,
+			<&adc11mux 0>, <&adc11mux 1>,
+			<&adc12mux 0>, <&adc12mux 1>,
+			<&adc13mux 0>, <&adc13mux 1>,
+			<&adc14mux 0>, <&adc14mux 1>,
+			<&adc15mux 0>, <&adc15mux 1>,
+			<&adc_i2c 0>, <&adc_i2c 1>,
+			<&adc_i2c 2>, <&adc_i2c 3>,
+			<&adc_i2c 4>, <&adc_i2c 5>,
+			<&adc_i2c 6>, <&adc_i2c 7>,
+			<&adc_i2c 8>, <&adc_i2c 9>,
+			<&adc_i2c 10>, <&adc_i2c 11>,
+			<&adc_i2c 12>, <&adc_i2c 13>,
+			<&adc_i2c 14>, <&adc_i2c 15>;
+	};
+};
+
+&mdio0 {
+	status = "okay";
+
+	ethphy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+	};
+};
+
+&mac0 {
+	status = "okay";
+
+	phy-mode = "rgmii";
+	phy-handle = <&ethphy0>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii1_default>;
+};
+
+&fmc {
+	status = "okay";
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bmc";
+		spi-max-frequency = <50000000>;
+#include "openbmc-flash-layout-64.dtsi"
+	};
+
+	flash@1 {
+		status = "okay";
+		m25p,fast-read;
+		label = "alt-bmc";
+		spi-max-frequency = <50000000>;
+#include "openbmc-flash-layout-64-alt.dtsi"
+	};
+};
+
+&spi1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spi1_default>;
+
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "pnor";
+		spi-max-frequency = <20000000>;
+	};
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&uart4 {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	temperature-sensor@2e {
+		compatible = "adi,adt7490";
+		reg = <0x2e>;
+	};
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+
+	psu@58 {
+		compatible = "pmbus";
+		reg = <0x58>;
+	};
+
+	psu@59 {
+		compatible = "pmbus";
+		reg = <0x59>;
+	};
+};
+
+&i2c3 {
+	status = "okay";
+};
+
+&i2c4 {
+	status = "okay";
+
+	adc_i2c: adc-i2c@16 {
+		compatible = "lltc,ltc2497";
+		reg = <0x16>;
+		vref-supply = <&voltage_mon_reg>;
+		#io-channel-cells = <1>;
+		status = "okay";
+	 };
+
+	eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+		pagesize = <32>;
+	};
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9545";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x70>;
+		i2c-mux-idle-disconnect;
+
+		i2c4_bus70_chn0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0>;
+
+			outlet_temp1: temperature-sensor@48 {
+				compatible = "ti,tmp75";
+				reg = <0x48>;
+			};
+			psu1_inlet_temp2: temperature-sensor@49 {
+				compatible = "ti,tmp75";
+				reg = <0x49>;
+			};
+		};
+
+		i2c4_bus70_chn1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x1>;
+
+			pcie_zone_temp1: temperature-sensor@48 {
+				compatible = "ti,tmp75";
+				reg = <0x48>;
+			};
+			psu0_inlet_temp2: temperature-sensor@49 {
+				compatible = "ti,tmp75";
+				reg = <0x49>;
+			};
+		};
+
+		i2c4_bus70_chn2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x2>;
+
+			pcie_zone_temp2: temperature-sensor@48 {
+				compatible = "ti,tmp75";
+				reg = <0x48>;
+			};
+			outlet_temp2: temperature-sensor@49 {
+				compatible = "ti,tmp75";
+				reg = <0x49>;
+			};
+		};
+
+		i2c4_bus70_chn3: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x3>;
+
+			mb_inlet_temp1: temperature-sensor@7c {
+				compatible = "microchip,emc1413";
+				reg = <0x7c>;
+			};
+			mb_inlet_temp2: temperature-sensor@4c {
+				compatible = "microchip,emc1413";
+				reg = <0x4c>;
+			};
+		};
+	};
+};
+
+&i2c5 {
+	status = "okay";
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x70>;
+		i2c-mux-idle-disconnect;
+	};
+};
+
+&i2c6 {
+	status = "okay";
+	rtc@51 {
+		compatible = "nxp,pcf85063a";
+		reg = <0x51>;
+	};
+};
+
+&i2c7 {
+	status = "okay";
+};
+
+&i2c9 {
+	status = "okay";
+};
+
+&i2c11 {
+	status = "okay";
+};
+
+&i2c14 {
+	status = "okay";
+	eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+		pagesize = <32>;
+	};
+
+	bmc_ast2600_cpu: temperature-sensor@35 {
+		compatible = "ti,tmp175";
+		reg = <0x35>;
+	};
+};
+
+&adc0 {
+	ref_voltage = <2500>;
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc0_default &pinctrl_adc1_default
+		&pinctrl_adc2_default &pinctrl_adc3_default
+		&pinctrl_adc4_default &pinctrl_adc5_default
+		&pinctrl_adc6_default &pinctrl_adc7_default>;
+};
+
+&adc1 {
+	ref_voltage = <2500>;
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc8_default &pinctrl_adc9_default
+		&pinctrl_adc10_default &pinctrl_adc11_default
+		&pinctrl_adc12_default &pinctrl_adc13_default
+		&pinctrl_adc14_default &pinctrl_adc15_default>;
+};
+
+&vhub {
+	status = "okay";
+};
+
+&video {
+	status = "okay";
+	memory-region = <&video_engine_memory>;
+};
+
+&gpio0 {
+	gpio-line-names =
+	/*A0-A7*/	"","","","","","i2c2-reset-n","i2c6-reset-n","i2c4-reset-n",
+	/*B0-B7*/	"","","","","host0-sysreset-n","host0-pmin-n","","",
+	/*C0-C7*/	"s0-vrd-fault-n","s1-vrd-fault-n","bmc-debug-mode","",
+			"irq-n","","vrd-sel","spd-sel",
+	/*D0-D7*/	"presence-ps0","presence-ps1","hsc-12vmain-alt2-n","ext-high-temp-n",
+			"","bmc-ncsi-txen","","",
+	/*E0-E7*/	"eth-phy-rst-n","eth-phy-int-n","clk50m-bmc-ncsi","","","","","",
+	/*F0-F7*/	"s0-pcp-oc-warn-n","s1-pcp-oc-warn-n","power-chassis-control",
+			"cpu-bios-recover","cpld-done","hs-scout-proc-hot",
+			"s0-vr-hot-n","s1-vr-hot-n",
+	/*G0-G7*/	"","","hsc-12vmain-alt1-n","bmc-salt12-s0-ssif-n","","","","",
+	/*H0-H7*/	"","fpga-program-b","wd-disable-n","power-chassis-good","","","","",
+	/*I0-I7*/	"","","","","","adc-sw","power-button","rtc-battery-voltage-read-enable",
+	/*J0-J7*/	"","","","","","","","",
+	/*K0-K7*/	"","","","","","","","",
+	/*L0-L7*/	"","","","","","","","",
+	/*M0-M7*/	"bmc-uart-cts1","s0-ddr-save","soc-spi-nor-access","presence-cpu0",
+			"s0-rtc-lock","","","",
+	/*N0-N7*/	"hpm-fw-recovery","hpm-stby-rst-n","jtag-sel-s0","led-sw-hb",
+			"jtag-dbgr-prsnt-n","","","",
+	/*O0-O7*/	"","","","","","","","",
+	/*P0-P7*/	"ps0-ac-loss-n","ps1-ac-loss-n","","",
+			"led-fault","cpld-user-mode","jtag-srst-n","led-bmc-hb",
+	/*Q0-Q7*/	"","","","","","","","",
+	/*R0-R7*/	"","","","","","","","",
+	/*S0-S7*/	"","","identify-button","led-identify",
+			"s1-ddr-save","spi-nor-access","sys-pgood","presence-cpu1",
+	/*T0-T7*/	"","","","","","","","",
+	/*U0-U7*/	"","","","","","","","",
+	/*V0-V7*/	"s0-hightemp-n","s0-fault-alert","s0-sys-auth-failure-n",
+			"host0-reboot-ack-n","host0-ready","host0-shd-req-n",
+			"host0-shd-ack-n","s0-overtemp-n",
+	/*W0-W7*/	"ocp-aux-pwren","ocp-main-pwren","ocp-pgood","",
+			"bmc-ok","bmc-ready","spi0-program-sel","spi0-backup-sel",
+	/*X0-X7*/	"i2c-backup-sel","s1-fault-alert","s1-fw-boot-ok",
+			"s1-hightemp-n","s0-spi-auth-fail-n","s1-sys-auth-failure-n",
+			"s1-overtemp-n","cpld-s1-spi-auth-fail-n",
+	/*Y0-Y7*/	"","","","","","","bmc-spi-fm-boot-abr-pd","host0-special-boot",
+	/*Z0-Z7*/	"reset-button","ps0-pgood","ps1-pgood","","","","","";
+};
+
+&gpio1 {
+	gpio-line-names =
+	/*18A0-18A7*/	"","","","","","","","",
+	/*18B0-18B7*/	"","","","","emmc-rst-n","","s0-soc-pgood","",
+	/*18C0-18C7*/	"uart1-mode0","uart1-mode1","uart2-mode0","uart2-mode1",
+			"uart3-mode0","uart3-mode1","uart4-mode0","uart4-mode1",
+	/*18D0-18D7*/	"","","","","","","","",
+	/*18E0-18E3*/	"","","","";
+};
+
-- 
2.35.1

Re: [PATCH v2 1/2] dt-bindings: arm: aspeed: document Ampere Mt.Mitchell BMC compatibles

[Krzysztof Kozlowski]

On 20/07/2022 10:52, Quan Nguyen wrote:
> Document Ampere Mt.Mitchell BMC board compatible.
> 
> Signed-off-by: Quan Nguyen <quan@os.amperecomputing.com>

Thank you for your patch. There is something to discuss/improve.

> ---
> v2:
>   + Introduce in v2 to add Ampere Mt. Mitchell BMC compatible [Krzysztof]
> 
>  Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml | 1 +
>  1 file changed, 1 insertion(+)
> 
> diff --git a/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml b/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml
> index d61408194998..b8146d5c4431 100644
> --- a/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml
> +++ b/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml
> @@ -71,6 +71,7 @@ properties:
>            - enum:
>                - aspeed,ast2600-evb
>                - aspeed,ast2600-evb-a1
> +              - ampere,mtmitchell-bmc

Put the entry ordered alphabetically.


Best regards,
Krzysztof

Re: [PATCH v2 2/2] ARM: dts: aspeed: Add device tree for Ampere's Mt. Mitchell BMC

[Krzysztof Kozlowski]

On 20/07/2022 10:52, Quan Nguyen wrote:
> The Mt. Mitchell BMC is an ASPEED AST2600-based BMC for the Mt. Mitchell
> hardware reference platform with AmpereOne(TM) processor.
> 
> Signed-off-by: Quan Nguyen <quan@os.amperecomputing.com>
> Signed-off-by: Phong Vo <phong@os.amperecomputing.com>
> Signed-off-by: Thang Q. Nguyen <thang@os.amperecomputing.com>
> ---
> v2 :
>   + Remove bootargs                                       [Krzysztof]
>   + Fix gpio-keys nodes name to conform with device tree binding
>   documents                                               [Krzysztof]
>   + Fix some nodes to use generic name                    [Krzysztof]
>   + Remove unnecessary blank line                         [Krzysztof]
>   + Fix typo "LTC" to "LLC" in license info and corrected license
>   info to GPL-2.0-only
> 
>  arch/arm/boot/dts/Makefile                    |   1 +
>  .../boot/dts/aspeed-bmc-ampere-mtmitchell.dts | 577 ++++++++++++++++++
>  2 files changed, 578 insertions(+)
>  create mode 100644 arch/arm/boot/dts/aspeed-bmc-ampere-mtmitchell.dts
> 

(...)

> +
> +&i2c3 {
> +	status = "okay";
> +};
> +
> +&i2c4 {
> +	status = "okay";
> +
> +	adc_i2c: adc-i2c@16 {

Node name: just "adc"

> +		compatible = "lltc,ltc2497";
> +		reg = <0x16>;
> +		vref-supply = <&voltage_mon_reg>;
> +		#io-channel-cells = <1>;
> +		status = "okay";

Isn't this new node? Why do you need status here?

> +	 };
> +
> +	eeprom@50 {
> +		compatible = "atmel,24c64";
> +		reg = <0x50>;
> +		pagesize = <32>;
> +	};
> +

(...)

> +
> +&gpio1 {
> +	gpio-line-names =
> +	/*18A0-18A7*/	"","","","","","","","",
> +	/*18B0-18B7*/	"","","","","emmc-rst-n","","s0-soc-pgood","",
> +	/*18C0-18C7*/	"uart1-mode0","uart1-mode1","uart2-mode0","uart2-mode1",
> +			"uart3-mode0","uart3-mode1","uart4-mode0","uart4-mode1",
> +	/*18D0-18D7*/	"","","","","","","","",
> +	/*18E0-18E3*/	"","","","";
> +};
> +

You have a trailing line error.


Best regards,
Krzysztof

Re: [PATCH v2 2/2] ARM: dts: aspeed: Add device tree for Ampere's Mt. Mitchell BMC

[Andrew Jeffery]

Hello,

On Wed, 20 Jul 2022, at 18:22, Quan Nguyen wrote:
> The Mt. Mitchell BMC is an ASPEED AST2600-based BMC for the Mt. Mitchell
> hardware reference platform with AmpereOne(TM) processor.
>
> Signed-off-by: Quan Nguyen <quan@os.amperecomputing.com>
> Signed-off-by: Phong Vo <phong@os.amperecomputing.com>
> Signed-off-by: Thang Q. Nguyen <thang@os.amperecomputing.com>
> ---
> v2 :
>   + Remove bootargs                                       [Krzysztof]
>   + Fix gpio-keys nodes name to conform with device tree binding
>   documents                                               [Krzysztof]
>   + Fix some nodes to use generic name                    [Krzysztof]
>   + Remove unnecessary blank line                         [Krzysztof]
>   + Fix typo "LTC" to "LLC" in license info and corrected license
>   info to GPL-2.0-only
>
>  arch/arm/boot/dts/Makefile                    |   1 +
>  .../boot/dts/aspeed-bmc-ampere-mtmitchell.dts | 577 ++++++++++++++++++
>  2 files changed, 578 insertions(+)
>  create mode 100644 arch/arm/boot/dts/aspeed-bmc-ampere-mtmitchell.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index f9484f5ef126..ecb9dafb8f1a 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -1573,6 +1573,7 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
>  	aspeed-ast2600-evb.dtb \
>  	aspeed-bmc-amd-ethanolx.dtb \
>  	aspeed-bmc-ampere-mtjade.dtb \
> +	aspeed-bmc-ampere-mtmitchell.dtb \
>  	aspeed-bmc-arm-centriq2400-rep.dtb \
>  	aspeed-bmc-arm-stardragon4800-rep2.dtb \
>  	aspeed-bmc-asrock-e3c246d4i.dtb \
> diff --git a/arch/arm/boot/dts/aspeed-bmc-ampere-mtmitchell.dts 
> b/arch/arm/boot/dts/aspeed-bmc-ampere-mtmitchell.dts
> new file mode 100644
> index 000000000000..2e68f5264bb1
> --- /dev/null
> +++ b/arch/arm/boot/dts/aspeed-bmc-ampere-mtmitchell.dts
> @@ -0,0 +1,577 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +// Copyright (c) 2022, Ampere Computing LLC
> +
> +/dts-v1/;
> +
> +#include "aspeed-g6.dtsi"
> +#include <dt-bindings/gpio/aspeed-gpio.h>
> +
> +/ {
> +	model = "Ampere Mt.Mitchell BMC";
> +	compatible = "ampere,mtmitchell-bmc", "aspeed,ast2600";
> +
> +	chosen {
> +		stdout-path = &uart5;
> +	};
> +
> +	memory@80000000 {
> +		device_type = "memory";
> +		reg = <0x80000000 0x80000000>;

This is 2GB of memory

> +	};
> +
> +	reserved-memory {
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		ranges;
> +
> +		gfx_memory: framebuffer {
> +			size = <0x01000000>;
> +			alignment = <0x01000000>;
> +			compatible = "shared-dma-pool";
> +			reusable;
> +		};
> +
> +		video_engine_memory: video {
> +			size = <0x04000000>;
> +			alignment = <0x01000000>;
> +			compatible = "shared-dma-pool";
> +			reusable;
> +		};
> +
> +		/* 1GB memory */

But you say 1GB of memory here

> +		vga_memory: region@bf000000 {
> +			no-map;
> +			compatible = "shared-dma-pool";
> +			reg = <0xbf000000 0x01000000>;  /* 16M */

And this makes sense for 1GB.

So I think your memory node has the wrong length in reg?

> +		};
> +	};
> +
> +	gpio-keys {
> +		compatible = "gpio-keys";
> +
> +		s0-overtemp-event {
> +			label = "S0_OVERTEMP";
> +			gpios = <&gpio0 ASPEED_GPIO(V, 7) GPIO_ACTIVE_LOW>;
> +			linux,code = <ASPEED_GPIO(V, 7)>;
> +		};
> +
> +		s0-hightemp-event {
> +			label = "S0_HIGHTEMP";
> +			gpios = <&gpio0 ASPEED_GPIO(V, 0) GPIO_ACTIVE_LOW>;
> +			linux,code = <ASPEED_GPIO(V, 0)>;
> +		};
> +
> +		s1-overtemp-event {
> +			label = "S1_OVERTEMP";
> +			gpios = <&gpio0 ASPEED_GPIO(X, 6) GPIO_ACTIVE_LOW>;
> +			linux,code = <ASPEED_GPIO(X, 6)>;
> +		};
> +
> +		s1-hightemp-event {
> +			label = "S1_HIGHTEMP";
> +			gpios = <&gpio0 ASPEED_GPIO(X, 3) GPIO_ACTIVE_LOW>;
> +			linux,code = <ASPEED_GPIO(X, 3)>;
> +		};
> +	};

I really want us to stop using GPIO keys and just poll the GPIO in userspace if necessary.

The discussion here might help, eventually:

https://gerrit.openbmc.org/c/openbmc/dbus-sensors/+/54740

> +
> +	voltage_mon_reg: voltage-mon-regulator {
> +		compatible = "regulator-fixed";
> +		regulator-name = "ltc2497_reg";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		regulator-always-on;
> +	};
> +
> +	gpioI5mux: mux-controller {
> +		compatible = "gpio-mux";
> +		#mux-control-cells = <0>;
> +		mux-gpios = <&gpio0 ASPEED_GPIO(I, 5) GPIO_ACTIVE_HIGH>;
> +	};
> +
> +	adc0mux: adc0mux {
> +		compatible = "io-channel-mux";
> +		io-channels = <&adc0 0>;
> +		#io-channel-cells = <1>;
> +		io-channel-names = "parent";
> +		mux-controls = <&gpioI5mux>;
> +		channels = "s0", "s1";
> +	};
> +
> +	adc1mux: adc1mux {
> +		compatible = "io-channel-mux";
> +		io-channels = <&adc0 1>;
> +		#io-channel-cells = <1>;
> +		io-channel-names = "parent";
> +		mux-controls = <&gpioI5mux>;
> +		channels = "s0", "s1";
> +	};
> +
> +	adc2mux: adc2mux {
> +		compatible = "io-channel-mux";
> +		io-channels = <&adc0 2>;
> +		#io-channel-cells = <1>;
> +		io-channel-names = "parent";
> +		mux-controls = <&gpioI5mux>;
> +		channels = "s0", "s1";
> +	};
> +
> +	adc3mux: adc3mux {
> +		compatible = "io-channel-mux";
> +		io-channels = <&adc0 3>;
> +		#io-channel-cells = <1>;
> +		io-channel-names = "parent";
> +		mux-controls = <&gpioI5mux>;
> +		channels = "s0", "s1";
> +	};
> +
> +	adc4mux: adc4mux {
> +		compatible = "io-channel-mux";
> +		io-channels = <&adc0 4>;
> +		#io-channel-cells = <1>;
> +		io-channel-names = "parent";
> +		mux-controls = <&gpioI5mux>;
> +		channels = "s0", "s1";
> +	};
> +
> +	adc5mux: adc5mux {
> +		compatible = "io-channel-mux";
> +		io-channels = <&adc0 5>;
> +		#io-channel-cells = <1>;
> +		io-channel-names = "parent";
> +		mux-controls = <&gpioI5mux>;
> +		channels = "s0", "s1";
> +	};
> +
> +	adc6mux: adc6mux {
> +		compatible = "io-channel-mux";
> +		io-channels = <&adc0 6>;
> +		#io-channel-cells = <1>;
> +		io-channel-names = "parent";
> +		mux-controls = <&gpioI5mux>;
> +		channels = "s0", "s1";
> +	};
> +
> +	adc7mux: adc7mux {
> +		compatible = "io-channel-mux";
> +		io-channels = <&adc0 7>;
> +		#io-channel-cells = <1>;
> +		io-channel-names = "parent";
> +		mux-controls = <&gpioI5mux>;
> +		channels = "s0", "s1";
> +	};
> +
> +	adc8mux: adc8mux {
> +		compatible = "io-channel-mux";
> +		io-channels = <&adc1 0>;
> +		#io-channel-cells = <1>;
> +		io-channel-names = "parent";
> +		mux-controls = <&gpioI5mux>;
> +		channels = "s0", "s1";
> +	};
> +
> +	adc9mux: adc9mux {
> +		compatible = "io-channel-mux";
> +		io-channels = <&adc1 1>;
> +		#io-channel-cells = <1>;
> +		io-channel-names = "parent";
> +		mux-controls = <&gpioI5mux>;
> +		channels = "s0", "s1";
> +	};
> +
> +	adc10mux: adc10mux {
> +		compatible = "io-channel-mux";
> +		io-channels = <&adc1 2>;
> +		#io-channel-cells = <1>;
> +		io-channel-names = "parent";
> +		mux-controls = <&gpioI5mux>;
> +		channels = "s0", "s1";
> +	};
> +
> +	adc11mux: adc11mux {
> +		compatible = "io-channel-mux";
> +		io-channels = <&adc1 3>;
> +		#io-channel-cells = <1>;
> +		io-channel-names = "parent";
> +		mux-controls = <&gpioI5mux>;
> +		channels = "s0", "s1";
> +	};
> +
> +	adc12mux: adc12mux {
> +		compatible = "io-channel-mux";
> +		io-channels = <&adc1 4>;
> +		#io-channel-cells = <1>;
> +		io-channel-names = "parent";
> +		mux-controls = <&gpioI5mux>;
> +		channels = "s0", "s1";
> +	};
> +
> +	adc13mux: adc13mux {
> +		compatible = "io-channel-mux";
> +		io-channels = <&adc1 5>;
> +		#io-channel-cells = <1>;
> +		io-channel-names = "parent";
> +		mux-controls = <&gpioI5mux>;
> +		channels = "s0", "s1";
> +	};
> +
> +	adc14mux: adc14mux {
> +		compatible = "io-channel-mux";
> +		io-channels = <&adc1 6>;
> +		#io-channel-cells = <1>;
> +		io-channel-names = "parent";
> +		mux-controls = <&gpioI5mux>;
> +		channels = "s0", "s1";
> +	};
> +
> +	adc15mux: adc15mux {
> +		compatible = "io-channel-mux";
> +		io-channels = <&adc1 7>;
> +		#io-channel-cells = <1>;
> +		io-channel-names = "parent";
> +		mux-controls = <&gpioI5mux>;
> +		channels = "s0", "s1";
> +	};
> +
> +	iio-hwmon {
> +		compatible = "iio-hwmon";
> +		io-channels = <&adc0mux 0>, <&adc0mux 1>,
> +			<&adc1mux 0>, <&adc1mux 1>,
> +			<&adc2mux 0>, <&adc2mux 1>,
> +			<&adc3mux 0>, <&adc3mux 1>,
> +			<&adc4mux 0>, <&adc4mux 1>,
> +			<&adc5mux 0>, <&adc5mux 1>,
> +			<&adc6mux 0>, <&adc6mux 1>,
> +			<&adc7mux 0>, <&adc7mux 1>,
> +			<&adc8mux 0>, <&adc8mux 1>,
> +			<&adc9mux 0>, <&adc9mux 1>,
> +			<&adc10mux 0>, <&adc10mux 1>,
> +			<&adc11mux 0>, <&adc11mux 1>,
> +			<&adc12mux 0>, <&adc12mux 1>,
> +			<&adc13mux 0>, <&adc13mux 1>,
> +			<&adc14mux 0>, <&adc14mux 1>,
> +			<&adc15mux 0>, <&adc15mux 1>,
> +			<&adc_i2c 0>, <&adc_i2c 1>,
> +			<&adc_i2c 2>, <&adc_i2c 3>,
> +			<&adc_i2c 4>, <&adc_i2c 5>,
> +			<&adc_i2c 6>, <&adc_i2c 7>,
> +			<&adc_i2c 8>, <&adc_i2c 9>,
> +			<&adc_i2c 10>, <&adc_i2c 11>,
> +			<&adc_i2c 12>, <&adc_i2c 13>,
> +			<&adc_i2c 14>, <&adc_i2c 15>;
> +	};
> +};
> +
> +&mdio0 {
> +	status = "okay";
> +
> +	ethphy0: ethernet-phy@0 {
> +		compatible = "ethernet-phy-ieee802.3-c22";
> +		reg = <0>;
> +	};
> +};
> +
> +&mac0 {
> +	status = "okay";
> +
> +	phy-mode = "rgmii";
> +	phy-handle = <&ethphy0>;
> +
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_rgmii1_default>;
> +};
> +
> +&fmc {
> +	status = "okay";
> +	flash@0 {
> +		status = "okay";
> +		m25p,fast-read;
> +		label = "bmc";
> +		spi-max-frequency = <50000000>;
> +#include "openbmc-flash-layout-64.dtsi"
> +	};
> +
> +	flash@1 {
> +		status = "okay";
> +		m25p,fast-read;
> +		label = "alt-bmc";
> +		spi-max-frequency = <50000000>;
> +#include "openbmc-flash-layout-64-alt.dtsi"
> +	};
> +};
> +
> +&spi1 {
> +	status = "okay";
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_spi1_default>;
> +
> +	flash@0 {
> +		status = "okay";
> +		m25p,fast-read;
> +		label = "pnor";
> +		spi-max-frequency = <20000000>;
> +	};
> +};
> +
> +&uart1 {
> +	status = "okay";
> +};
> +
> +&uart2 {
> +	status = "okay";
> +};
> +
> +&uart3 {
> +	status = "okay";
> +};
> +
> +&uart4 {
> +	status = "okay";
> +};
> +
> +&i2c0 {
> +	status = "okay";
> +
> +	temperature-sensor@2e {
> +		compatible = "adi,adt7490";
> +		reg = <0x2e>;
> +	};
> +};
> +
> +&i2c1 {
> +	status = "okay";
> +};
> +
> +&i2c2 {
> +	status = "okay";
> +
> +	psu@58 {
> +		compatible = "pmbus";
> +		reg = <0x58>;
> +	};
> +
> +	psu@59 {
> +		compatible = "pmbus";
> +		reg = <0x59>;
> +	};
> +};
> +
> +&i2c3 {
> +	status = "okay";
> +};
> +
> +&i2c4 {
> +	status = "okay";
> +
> +	adc_i2c: adc-i2c@16 {
> +		compatible = "lltc,ltc2497";
> +		reg = <0x16>;
> +		vref-supply = <&voltage_mon_reg>;
> +		#io-channel-cells = <1>;
> +		status = "okay";
> +	 };
> +
> +	eeprom@50 {
> +		compatible = "atmel,24c64";
> +		reg = <0x50>;
> +		pagesize = <32>;
> +	};
> +
> +	i2c-mux@70 {
> +		compatible = "nxp,pca9545";
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		reg = <0x70>;
> +		i2c-mux-idle-disconnect;
> +
> +		i2c4_bus70_chn0: i2c@0 {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			reg = <0x0>;
> +
> +			outlet_temp1: temperature-sensor@48 {
> +				compatible = "ti,tmp75";
> +				reg = <0x48>;
> +			};
> +			psu1_inlet_temp2: temperature-sensor@49 {
> +				compatible = "ti,tmp75";
> +				reg = <0x49>;
> +			};
> +		};
> +
> +		i2c4_bus70_chn1: i2c@1 {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			reg = <0x1>;
> +
> +			pcie_zone_temp1: temperature-sensor@48 {
> +				compatible = "ti,tmp75";
> +				reg = <0x48>;
> +			};
> +			psu0_inlet_temp2: temperature-sensor@49 {
> +				compatible = "ti,tmp75";
> +				reg = <0x49>;
> +			};
> +		};
> +
> +		i2c4_bus70_chn2: i2c@2 {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			reg = <0x2>;
> +
> +			pcie_zone_temp2: temperature-sensor@48 {
> +				compatible = "ti,tmp75";
> +				reg = <0x48>;
> +			};
> +			outlet_temp2: temperature-sensor@49 {
> +				compatible = "ti,tmp75";
> +				reg = <0x49>;
> +			};
> +		};
> +
> +		i2c4_bus70_chn3: i2c@3 {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			reg = <0x3>;
> +
> +			mb_inlet_temp1: temperature-sensor@7c {
> +				compatible = "microchip,emc1413";
> +				reg = <0x7c>;
> +			};
> +			mb_inlet_temp2: temperature-sensor@4c {
> +				compatible = "microchip,emc1413";
> +				reg = <0x4c>;
> +			};
> +		};
> +	};
> +};
> +
> +&i2c5 {
> +	status = "okay";
> +
> +	i2c-mux@70 {
> +		compatible = "nxp,pca9548";
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		reg = <0x70>;
> +		i2c-mux-idle-disconnect;
> +	};
> +};
> +
> +&i2c6 {
> +	status = "okay";
> +	rtc@51 {
> +		compatible = "nxp,pcf85063a";
> +		reg = <0x51>;
> +	};
> +};
> +
> +&i2c7 {
> +	status = "okay";
> +};
> +
> +&i2c9 {
> +	status = "okay";
> +};
> +
> +&i2c11 {
> +	status = "okay";
> +};
> +
> +&i2c14 {
> +	status = "okay";
> +	eeprom@50 {
> +		compatible = "atmel,24c64";
> +		reg = <0x50>;
> +		pagesize = <32>;
> +	};
> +
> +	bmc_ast2600_cpu: temperature-sensor@35 {
> +		compatible = "ti,tmp175";
> +		reg = <0x35>;
> +	};
> +};
> +
> +&adc0 {
> +	ref_voltage = <2500>;
> +	status = "okay";
> +
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_adc0_default &pinctrl_adc1_default
> +		&pinctrl_adc2_default &pinctrl_adc3_default
> +		&pinctrl_adc4_default &pinctrl_adc5_default
> +		&pinctrl_adc6_default &pinctrl_adc7_default>;
> +};
> +
> +&adc1 {
> +	ref_voltage = <2500>;
> +	status = "okay";
> +
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_adc8_default &pinctrl_adc9_default
> +		&pinctrl_adc10_default &pinctrl_adc11_default
> +		&pinctrl_adc12_default &pinctrl_adc13_default
> +		&pinctrl_adc14_default &pinctrl_adc15_default>;
> +};
> +
> +&vhub {
> +	status = "okay";
> +};
> +
> +&video {
> +	status = "okay";
> +	memory-region = <&video_engine_memory>;
> +};
> +
> +&gpio0 {
> +	gpio-line-names =
> +	/*A0-A7*/	"","","","","","i2c2-reset-n","i2c6-reset-n","i2c4-reset-n",
> +	/*B0-B7*/	"","","","","host0-sysreset-n","host0-pmin-n","","",
> +	/*C0-C7*/	"s0-vrd-fault-n","s1-vrd-fault-n","bmc-debug-mode","",

Mildly interested in the functionality of "bmc-debug-mode" :)

> +			"irq-n","","vrd-sel","spd-sel",
> +	/*D0-D7*/	"presence-ps0","presence-ps1","hsc-12vmain-alt2-n","ext-high-temp-n",
> +			"","bmc-ncsi-txen","","",

Is "bmc-ncsi-txen" something that should be associated with the MAC?

> +	/*E0-E7*/	"eth-phy-rst-n","eth-phy-int-n","clk50m-bmc-ncsi","","","","","",

Same question for eth-phy-rst-n and eth-phy-int-n.

> +	/*F0-F7*/	"s0-pcp-oc-warn-n","s1-pcp-oc-warn-n","power-chassis-control",
> +			"cpu-bios-recover","cpld-done","hs-scout-proc-hot",
> +			"s0-vr-hot-n","s1-vr-hot-n",
> +	/*G0-G7*/	"","","hsc-12vmain-alt1-n","bmc-salt12-s0-ssif-n","","","","",
> +	/*H0-H7*/	"","fpga-program-b","wd-disable-n","power-chassis-good","","","","",
> +	/*I0-I7*/	"","","","","","adc-sw","power-button","rtc-battery-voltage-read-enable",
> +	/*J0-J7*/	"","","","","","","","",
> +	/*K0-K7*/	"","","","","","","","",
> +	/*L0-L7*/	"","","","","","","","",
> +	/*M0-M7*/	"bmc-uart-cts1","s0-ddr-save","soc-spi-nor-access","presence-cpu0",
> +			"s0-rtc-lock","","","",

Why isn't "bmc-uart-cts1" muxed into the associated UART? Why is it a GPIO?

> +	/*N0-N7*/	"hpm-fw-recovery","hpm-stby-rst-n","jtag-sel-s0","led-sw-hb",
> +			"jtag-dbgr-prsnt-n","","","",
> +	/*O0-O7*/	"","","","","","","","",
> +	/*P0-P7*/	"ps0-ac-loss-n","ps1-ac-loss-n","","",
> +			"led-fault","cpld-user-mode","jtag-srst-n","led-bmc-hb",
> +	/*Q0-Q7*/	"","","","","","","","",
> +	/*R0-R7*/	"","","","","","","","",
> +	/*S0-S7*/	"","","identify-button","led-identify",
> +			"s1-ddr-save","spi-nor-access","sys-pgood","presence-cpu1",
> +	/*T0-T7*/	"","","","","","","","",
> +	/*U0-U7*/	"","","","","","","","",
> +	/*V0-V7*/	"s0-hightemp-n","s0-fault-alert","s0-sys-auth-failure-n",
> +			"host0-reboot-ack-n","host0-ready","host0-shd-req-n",
> +			"host0-shd-ack-n","s0-overtemp-n",
> +	/*W0-W7*/	"ocp-aux-pwren","ocp-main-pwren","ocp-pgood","",
> +			"bmc-ok","bmc-ready","spi0-program-sel","spi0-backup-sel",
> +	/*X0-X7*/	"i2c-backup-sel","s1-fault-alert","s1-fw-boot-ok",
> +			"s1-hightemp-n","s0-spi-auth-fail-n","s1-sys-auth-failure-n",
> +			"s1-overtemp-n","cpld-s1-spi-auth-fail-n",
> +	/*Y0-Y7*/	"","","","","","","bmc-spi-fm-boot-abr-pd","host0-special-boot",
> +	/*Z0-Z7*/	"reset-button","ps0-pgood","ps1-pgood","","","","","";
> +};
> +
> +&gpio1 {
> +	gpio-line-names =
> +	/*18A0-18A7*/	"","","","","","","","",
> +	/*18B0-18B7*/	"","","","","emmc-rst-n","","s0-soc-pgood","",

"emmc-rst-n" should be specified as part of mmc-pwrseq-emmc, right?

https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/mmc/mmc-pwrseq-emmc.yaml?h=v5.19-rc7

Cheers,

Andrew

Re: [PATCH v2 2/2] ARM: dts: aspeed: Add device tree for Ampere's Mt. Mitchell BMC

[Quan Nguyen]

On 20/07/2022 17:36, Krzysztof Kozlowski wrote:
> On 20/07/2022 10:52, Quan Nguyen wrote:
>> The Mt. Mitchell BMC is an ASPEED AST2600-based BMC for the Mt. Mitchell
>> hardware reference platform with AmpereOne(TM) processor.
>>
>> Signed-off-by: Quan Nguyen <quan@os.amperecomputing.com>
>> Signed-off-by: Phong Vo <phong@os.amperecomputing.com>
>> Signed-off-by: Thang Q. Nguyen <thang@os.amperecomputing.com>
>> ---
>> v2 :
>>    + Remove bootargs                                       [Krzysztof]
>>    + Fix gpio-keys nodes name to conform with device tree binding
>>    documents                                               [Krzysztof]
>>    + Fix some nodes to use generic name                    [Krzysztof]
>>    + Remove unnecessary blank line                         [Krzysztof]
>>    + Fix typo "LTC" to "LLC" in license info and corrected license
>>    info to GPL-2.0-only
>>
>>   arch/arm/boot/dts/Makefile                    |   1 +
>>   .../boot/dts/aspeed-bmc-ampere-mtmitchell.dts | 577 ++++++++++++++++++
>>   2 files changed, 578 insertions(+)
>>   create mode 100644 arch/arm/boot/dts/aspeed-bmc-ampere-mtmitchell.dts
>>
> 
> (...)
> 
>> +
>> +&i2c3 {
>> +	status = "okay";
>> +};
>> +
>> +&i2c4 {
>> +	status = "okay";
>> +
>> +	adc_i2c: adc-i2c@16 {
> 
> Node name: just "adc"
> 

Thanks, will fix.

>> +		compatible = "lltc,ltc2497";
>> +		reg = <0x16>;
>> +		vref-supply = <&voltage_mon_reg>;
>> +		#io-channel-cells = <1>;
>> +		status = "okay";
> 
> Isn't this new node? Why do you need status here?
> 
Thanks for the comment. The drivers/iio/adc/ltc2497.c does not check for 
the status indeed. Will remove it.

>> +	 };
>> +
>> +	eeprom@50 {
>> +		compatible = "atmel,24c64";
>> +		reg = <0x50>;
>> +		pagesize = <32>;
>> +	};
>> +
> 
> (...)
> 
>> +
>> +&gpio1 {
>> +	gpio-line-names =
>> +	/*18A0-18A7*/	"","","","","","","","",
>> +	/*18B0-18B7*/	"","","","","emmc-rst-n","","s0-soc-pgood","",
>> +	/*18C0-18C7*/	"uart1-mode0","uart1-mode1","uart2-mode0","uart2-mode1",
>> +			"uart3-mode0","uart3-mode1","uart4-mode0","uart4-mode1",
>> +	/*18D0-18D7*/	"","","","","","","","",
>> +	/*18E0-18E3*/	"","","","";
>> +};
>> +
> 
> You have a trailing line error.
> 
> 
Thanks, will fix
- Quan

Re: [PATCH v2 1/2] dt-bindings: arm: aspeed: document Ampere Mt.Mitchell BMC compatibles

[Quan Nguyen]

On 20/07/2022 17:34, Krzysztof Kozlowski wrote:
> On 20/07/2022 10:52, Quan Nguyen wrote:
>> Document Ampere Mt.Mitchell BMC board compatible.
>>
>> Signed-off-by: Quan Nguyen <quan@os.amperecomputing.com>
> 
> Thank you for your patch. There is something to discuss/improve.
> 
>> ---
>> v2:
>>    + Introduce in v2 to add Ampere Mt. Mitchell BMC compatible [Krzysztof]
>>
>>   Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml | 1 +
>>   1 file changed, 1 insertion(+)
>>
>> diff --git a/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml b/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml
>> index d61408194998..b8146d5c4431 100644
>> --- a/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml
>> +++ b/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml
>> @@ -71,6 +71,7 @@ properties:
>>             - enum:
>>                 - aspeed,ast2600-evb
>>                 - aspeed,ast2600-evb-a1
>> +              - ampere,mtmitchell-bmc
> 
> Put the entry ordered alphabetically.
> 

Thanks Krzysztof for the review.

Will change to :
              - enum:
  +              - ampere,mtmitchell-bmc
                 - aspeed,ast2600-evb
                 - aspeed,ast2600-evb-a1

But, should we correct the below as well? ie: to move 
"ampere,mtjade-bmc" to before "aspeed,ast2500-evb" ?

- description: AST2500 based boards
         items:
           - enum:
               - aspeed,ast2500-evb
               - amd,ethanolx-bmc
               - ampere,mtjade-bmc
               - asrock,e3c246d4i-bmc

Thanks,
- Quan

Re: [PATCH v2 1/2] dt-bindings: arm: aspeed: document Ampere Mt.Mitchell BMC compatibles

[Krzysztof Kozlowski]

On 21/07/2022 04:46, Quan Nguyen wrote:
> 
> 
> On 20/07/2022 17:34, Krzysztof Kozlowski wrote:
>> On 20/07/2022 10:52, Quan Nguyen wrote:
>>> Document Ampere Mt.Mitchell BMC board compatible.
>>>
>>> Signed-off-by: Quan Nguyen <quan@os.amperecomputing.com>
>>
>> Thank you for your patch. There is something to discuss/improve.
>>
>>> ---
>>> v2:
>>>    + Introduce in v2 to add Ampere Mt. Mitchell BMC compatible [Krzysztof]
>>>
>>>   Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml | 1 +
>>>   1 file changed, 1 insertion(+)
>>>
>>> diff --git a/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml b/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml
>>> index d61408194998..b8146d5c4431 100644
>>> --- a/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml
>>> +++ b/Documentation/devicetree/bindings/arm/aspeed/aspeed.yaml
>>> @@ -71,6 +71,7 @@ properties:
>>>             - enum:
>>>                 - aspeed,ast2600-evb
>>>                 - aspeed,ast2600-evb-a1
>>> +              - ampere,mtmitchell-bmc
>>
>> Put the entry ordered alphabetically.
>>
> 
> Thanks Krzysztof for the review.
> 
> Will change to :
>               - enum:
>   +              - ampere,mtmitchell-bmc
>                  - aspeed,ast2600-evb
>                  - aspeed,ast2600-evb-a1
> 
> But, should we correct the below as well? ie: to move 
> "ampere,mtjade-bmc" to before "aspeed,ast2500-evb" ?
> 
Oops, indeed, I added aspeed in wrong place. I'll correct it in my tree.

Best regards,
Krzysztof

Re: [PATCH v2 2/2] ARM: dts: aspeed: Add device tree for Ampere's Mt. Mitchell BMC

[Quan Nguyen]

Thanks Andrew for the review.

On 21/07/2022 09:02, Andrew Jeffery wrote:
> Hello,
> 
> On Wed, 20 Jul 2022, at 18:22, Quan Nguyen wrote:
>> The Mt. Mitchell BMC is an ASPEED AST2600-based BMC for the Mt. Mitchell
>> hardware reference platform with AmpereOne(TM) processor.
>>
>> Signed-off-by: Quan Nguyen <quan@os.amperecomputing.com>
>> Signed-off-by: Phong Vo <phong@os.amperecomputing.com>
>> Signed-off-by: Thang Q. Nguyen <thang@os.amperecomputing.com>
>> ---
>> v2 :
>>    + Remove bootargs                                       [Krzysztof]
>>    + Fix gpio-keys nodes name to conform with device tree binding
>>    documents                                               [Krzysztof]
>>    + Fix some nodes to use generic name                    [Krzysztof]
>>    + Remove unnecessary blank line                         [Krzysztof]
>>    + Fix typo "LTC" to "LLC" in license info and corrected license
>>    info to GPL-2.0-only
>>
>>   arch/arm/boot/dts/Makefile                    |   1 +
>>   .../boot/dts/aspeed-bmc-ampere-mtmitchell.dts | 577 ++++++++++++++++++
>>   2 files changed, 578 insertions(+)
>>   create mode 100644 arch/arm/boot/dts/aspeed-bmc-ampere-mtmitchell.dts
>>
>> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
>> index f9484f5ef126..ecb9dafb8f1a 100644
>> --- a/arch/arm/boot/dts/Makefile
>> +++ b/arch/arm/boot/dts/Makefile
>> @@ -1573,6 +1573,7 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
>>   	aspeed-ast2600-evb.dtb \
>>   	aspeed-bmc-amd-ethanolx.dtb \
>>   	aspeed-bmc-ampere-mtjade.dtb \
>> +	aspeed-bmc-ampere-mtmitchell.dtb \
>>   	aspeed-bmc-arm-centriq2400-rep.dtb \
>>   	aspeed-bmc-arm-stardragon4800-rep2.dtb \
>>   	aspeed-bmc-asrock-e3c246d4i.dtb \
>> diff --git a/arch/arm/boot/dts/aspeed-bmc-ampere-mtmitchell.dts
>> b/arch/arm/boot/dts/aspeed-bmc-ampere-mtmitchell.dts
>> new file mode 100644
>> index 000000000000..2e68f5264bb1
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/aspeed-bmc-ampere-mtmitchell.dts
>> @@ -0,0 +1,577 @@
>> +// SPDX-License-Identifier: GPL-2.0-only
>> +// Copyright (c) 2022, Ampere Computing LLC
>> +
>> +/dts-v1/;
>> +
>> +#include "aspeed-g6.dtsi"
>> +#include <dt-bindings/gpio/aspeed-gpio.h>
>> +
>> +/ {
>> +	model = "Ampere Mt.Mitchell BMC";
>> +	compatible = "ampere,mtmitchell-bmc", "aspeed,ast2600";
>> +
>> +	chosen {
>> +		stdout-path = &uart5;
>> +	};
>> +
>> +	memory@80000000 {
>> +		device_type = "memory";
>> +		reg = <0x80000000 0x80000000>;
> 
> This is 2GB of memory
> 
>> +	};
>> +
>> +	reserved-memory {
>> +		#address-cells = <1>;
>> +		#size-cells = <1>;
>> +		ranges;
>> +
>> +		gfx_memory: framebuffer {
>> +			size = <0x01000000>;
>> +			alignment = <0x01000000>;
>> +			compatible = "shared-dma-pool";
>> +			reusable;
>> +		};
>> +
>> +		video_engine_memory: video {
>> +			size = <0x04000000>;
>> +			alignment = <0x01000000>;
>> +			compatible = "shared-dma-pool";
>> +			reusable;
>> +		};
>> +
>> +		/* 1GB memory */
> 
> But you say 1GB of memory here
> 

Thank you for the review.

This comment will be removed in next version.

>> +		vga_memory: region@bf000000 {
>> +			no-map;
>> +			compatible = "shared-dma-pool";
>> +			reg = <0xbf000000 0x01000000>;  /* 16M */
> 
> And this makes sense for 1GB.
> 
> So I think your memory node has the wrong length in reg?
> 
>> +		};
>> +	};
>> +
>> +	gpio-keys {
>> +		compatible = "gpio-keys";
>> +
>> +		s0-overtemp-event {
>> +			label = "S0_OVERTEMP";
>> +			gpios = <&gpio0 ASPEED_GPIO(V, 7) GPIO_ACTIVE_LOW>;
>> +			linux,code = <ASPEED_GPIO(V, 7)>;
>> +		};
>> +
>> +		s0-hightemp-event {
>> +			label = "S0_HIGHTEMP";
>> +			gpios = <&gpio0 ASPEED_GPIO(V, 0) GPIO_ACTIVE_LOW>;
>> +			linux,code = <ASPEED_GPIO(V, 0)>;
>> +		};
>> +
>> +		s1-overtemp-event {
>> +			label = "S1_OVERTEMP";
>> +			gpios = <&gpio0 ASPEED_GPIO(X, 6) GPIO_ACTIVE_LOW>;
>> +			linux,code = <ASPEED_GPIO(X, 6)>;
>> +		};
>> +
>> +		s1-hightemp-event {
>> +			label = "S1_HIGHTEMP";
>> +			gpios = <&gpio0 ASPEED_GPIO(X, 3) GPIO_ACTIVE_LOW>;
>> +			linux,code = <ASPEED_GPIO(X, 3)>;
>> +		};
>> +	};
> 
> I really want us to stop using GPIO keys and just poll the GPIO in userspace if necessary.
> 
> The discussion here might help, eventually:
> 
> https://gerrit.openbmc.org/c/openbmc/dbus-sensors/+/54740
> 

Will remove them in next version.

BTW, We are testing with phosphor-multi-gpio-monitor daemon but facing 
issue as there is only one target (we are interesting on both RASING and 
FALLING edge of the gpio) and no extra information passed to the target 
to indicate whether it is on RAISING or FALLING edge of the gpio line.

>> +
>> +	voltage_mon_reg: voltage-mon-regulator {
>> +		compatible = "regulator-fixed";
>> +		regulator-name = "ltc2497_reg";
>> +		regulator-min-microvolt = <3300000>;
>> +		regulator-max-microvolt = <3300000>;
>> +		regulator-always-on;
>> +	};
>> +
>> +	gpioI5mux: mux-controller {
>> +		compatible = "gpio-mux";
>> +		#mux-control-cells = <0>;
>> +		mux-gpios = <&gpio0 ASPEED_GPIO(I, 5) GPIO_ACTIVE_HIGH>;
>> +	};
>> +
>> +	adc0mux: adc0mux {
>> +		compatible = "io-channel-mux";
>> +		io-channels = <&adc0 0>;
>> +		#io-channel-cells = <1>;
>> +		io-channel-names = "parent";
>> +		mux-controls = <&gpioI5mux>;
>> +		channels = "s0", "s1";
>> +	};
>> +
>> +	adc1mux: adc1mux {
>> +		compatible = "io-channel-mux";
>> +		io-channels = <&adc0 1>;
>> +		#io-channel-cells = <1>;
>> +		io-channel-names = "parent";
>> +		mux-controls = <&gpioI5mux>;
>> +		channels = "s0", "s1";
>> +	};
>> +
>> +	adc2mux: adc2mux {
>> +		compatible = "io-channel-mux";
>> +		io-channels = <&adc0 2>;
>> +		#io-channel-cells = <1>;
>> +		io-channel-names = "parent";
>> +		mux-controls = <&gpioI5mux>;
>> +		channels = "s0", "s1";
>> +	};
>> +
>> +	adc3mux: adc3mux {
>> +		compatible = "io-channel-mux";
>> +		io-channels = <&adc0 3>;
>> +		#io-channel-cells = <1>;
>> +		io-channel-names = "parent";
>> +		mux-controls = <&gpioI5mux>;
>> +		channels = "s0", "s1";
>> +	};
>> +
>> +	adc4mux: adc4mux {
>> +		compatible = "io-channel-mux";
>> +		io-channels = <&adc0 4>;
>> +		#io-channel-cells = <1>;
>> +		io-channel-names = "parent";
>> +		mux-controls = <&gpioI5mux>;
>> +		channels = "s0", "s1";
>> +	};
>> +
>> +	adc5mux: adc5mux {
>> +		compatible = "io-channel-mux";
>> +		io-channels = <&adc0 5>;
>> +		#io-channel-cells = <1>;
>> +		io-channel-names = "parent";
>> +		mux-controls = <&gpioI5mux>;
>> +		channels = "s0", "s1";
>> +	};
>> +
>> +	adc6mux: adc6mux {
>> +		compatible = "io-channel-mux";
>> +		io-channels = <&adc0 6>;
>> +		#io-channel-cells = <1>;
>> +		io-channel-names = "parent";
>> +		mux-controls = <&gpioI5mux>;
>> +		channels = "s0", "s1";
>> +	};
>> +
>> +	adc7mux: adc7mux {
>> +		compatible = "io-channel-mux";
>> +		io-channels = <&adc0 7>;
>> +		#io-channel-cells = <1>;
>> +		io-channel-names = "parent";
>> +		mux-controls = <&gpioI5mux>;
>> +		channels = "s0", "s1";
>> +	};
>> +
>> +	adc8mux: adc8mux {
>> +		compatible = "io-channel-mux";
>> +		io-channels = <&adc1 0>;
>> +		#io-channel-cells = <1>;
>> +		io-channel-names = "parent";
>> +		mux-controls = <&gpioI5mux>;
>> +		channels = "s0", "s1";
>> +	};
>> +
>> +	adc9mux: adc9mux {
>> +		compatible = "io-channel-mux";
>> +		io-channels = <&adc1 1>;
>> +		#io-channel-cells = <1>;
>> +		io-channel-names = "parent";
>> +		mux-controls = <&gpioI5mux>;
>> +		channels = "s0", "s1";
>> +	};
>> +
>> +	adc10mux: adc10mux {
>> +		compatible = "io-channel-mux";
>> +		io-channels = <&adc1 2>;
>> +		#io-channel-cells = <1>;
>> +		io-channel-names = "parent";
>> +		mux-controls = <&gpioI5mux>;
>> +		channels = "s0", "s1";
>> +	};
>> +
>> +	adc11mux: adc11mux {
>> +		compatible = "io-channel-mux";
>> +		io-channels = <&adc1 3>;
>> +		#io-channel-cells = <1>;
>> +		io-channel-names = "parent";
>> +		mux-controls = <&gpioI5mux>;
>> +		channels = "s0", "s1";
>> +	};
>> +
>> +	adc12mux: adc12mux {
>> +		compatible = "io-channel-mux";
>> +		io-channels = <&adc1 4>;
>> +		#io-channel-cells = <1>;
>> +		io-channel-names = "parent";
>> +		mux-controls = <&gpioI5mux>;
>> +		channels = "s0", "s1";
>> +	};
>> +
>> +	adc13mux: adc13mux {
>> +		compatible = "io-channel-mux";
>> +		io-channels = <&adc1 5>;
>> +		#io-channel-cells = <1>;
>> +		io-channel-names = "parent";
>> +		mux-controls = <&gpioI5mux>;
>> +		channels = "s0", "s1";
>> +	};
>> +
>> +	adc14mux: adc14mux {
>> +		compatible = "io-channel-mux";
>> +		io-channels = <&adc1 6>;
>> +		#io-channel-cells = <1>;
>> +		io-channel-names = "parent";
>> +		mux-controls = <&gpioI5mux>;
>> +		channels = "s0", "s1";
>> +	};
>> +
>> +	adc15mux: adc15mux {
>> +		compatible = "io-channel-mux";
>> +		io-channels = <&adc1 7>;
>> +		#io-channel-cells = <1>;
>> +		io-channel-names = "parent";
>> +		mux-controls = <&gpioI5mux>;
>> +		channels = "s0", "s1";
>> +	};
>> +
>> +	iio-hwmon {
>> +		compatible = "iio-hwmon";
>> +		io-channels = <&adc0mux 0>, <&adc0mux 1>,
>> +			<&adc1mux 0>, <&adc1mux 1>,
>> +			<&adc2mux 0>, <&adc2mux 1>,
>> +			<&adc3mux 0>, <&adc3mux 1>,
>> +			<&adc4mux 0>, <&adc4mux 1>,
>> +			<&adc5mux 0>, <&adc5mux 1>,
>> +			<&adc6mux 0>, <&adc6mux 1>,
>> +			<&adc7mux 0>, <&adc7mux 1>,
>> +			<&adc8mux 0>, <&adc8mux 1>,
>> +			<&adc9mux 0>, <&adc9mux 1>,
>> +			<&adc10mux 0>, <&adc10mux 1>,
>> +			<&adc11mux 0>, <&adc11mux 1>,
>> +			<&adc12mux 0>, <&adc12mux 1>,
>> +			<&adc13mux 0>, <&adc13mux 1>,
>> +			<&adc14mux 0>, <&adc14mux 1>,
>> +			<&adc15mux 0>, <&adc15mux 1>,
>> +			<&adc_i2c 0>, <&adc_i2c 1>,
>> +			<&adc_i2c 2>, <&adc_i2c 3>,
>> +			<&adc_i2c 4>, <&adc_i2c 5>,
>> +			<&adc_i2c 6>, <&adc_i2c 7>,
>> +			<&adc_i2c 8>, <&adc_i2c 9>,
>> +			<&adc_i2c 10>, <&adc_i2c 11>,
>> +			<&adc_i2c 12>, <&adc_i2c 13>,
>> +			<&adc_i2c 14>, <&adc_i2c 15>;
>> +	};
>> +};
>> +
>> +&mdio0 {
>> +	status = "okay";
>> +
>> +	ethphy0: ethernet-phy@0 {
>> +		compatible = "ethernet-phy-ieee802.3-c22";
>> +		reg = <0>;
>> +	};
>> +};
>> +
>> +&mac0 {
>> +	status = "okay";
>> +
>> +	phy-mode = "rgmii";
>> +	phy-handle = <&ethphy0>;
>> +
>> +	pinctrl-names = "default";
>> +	pinctrl-0 = <&pinctrl_rgmii1_default>;
>> +};
>> +
>> +&fmc {
>> +	status = "okay";
>> +	flash@0 {
>> +		status = "okay";
>> +		m25p,fast-read;
>> +		label = "bmc";
>> +		spi-max-frequency = <50000000>;
>> +#include "openbmc-flash-layout-64.dtsi"
>> +	};
>> +
>> +	flash@1 {
>> +		status = "okay";
>> +		m25p,fast-read;
>> +		label = "alt-bmc";
>> +		spi-max-frequency = <50000000>;
>> +#include "openbmc-flash-layout-64-alt.dtsi"
>> +	};
>> +};
>> +
>> +&spi1 {
>> +	status = "okay";
>> +	pinctrl-names = "default";
>> +	pinctrl-0 = <&pinctrl_spi1_default>;
>> +
>> +	flash@0 {
>> +		status = "okay";
>> +		m25p,fast-read;
>> +		label = "pnor";
>> +		spi-max-frequency = <20000000>;
>> +	};
>> +};
>> +
>> +&uart1 {
>> +	status = "okay";
>> +};
>> +
>> +&uart2 {
>> +	status = "okay";
>> +};
>> +
>> +&uart3 {
>> +	status = "okay";
>> +};
>> +
>> +&uart4 {
>> +	status = "okay";
>> +};
>> +
>> +&i2c0 {
>> +	status = "okay";
>> +
>> +	temperature-sensor@2e {
>> +		compatible = "adi,adt7490";
>> +		reg = <0x2e>;
>> +	};
>> +};
>> +
>> +&i2c1 {
>> +	status = "okay";
>> +};
>> +
>> +&i2c2 {
>> +	status = "okay";
>> +
>> +	psu@58 {
>> +		compatible = "pmbus";
>> +		reg = <0x58>;
>> +	};
>> +
>> +	psu@59 {
>> +		compatible = "pmbus";
>> +		reg = <0x59>;
>> +	};
>> +};
>> +
>> +&i2c3 {
>> +	status = "okay";
>> +};
>> +
>> +&i2c4 {
>> +	status = "okay";
>> +
>> +	adc_i2c: adc-i2c@16 {
>> +		compatible = "lltc,ltc2497";
>> +		reg = <0x16>;
>> +		vref-supply = <&voltage_mon_reg>;
>> +		#io-channel-cells = <1>;
>> +		status = "okay";
>> +	 };
>> +
>> +	eeprom@50 {
>> +		compatible = "atmel,24c64";
>> +		reg = <0x50>;
>> +		pagesize = <32>;
>> +	};
>> +
>> +	i2c-mux@70 {
>> +		compatible = "nxp,pca9545";
>> +		#address-cells = <1>;
>> +		#size-cells = <0>;
>> +		reg = <0x70>;
>> +		i2c-mux-idle-disconnect;
>> +
>> +		i2c4_bus70_chn0: i2c@0 {
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +			reg = <0x0>;
>> +
>> +			outlet_temp1: temperature-sensor@48 {
>> +				compatible = "ti,tmp75";
>> +				reg = <0x48>;
>> +			};
>> +			psu1_inlet_temp2: temperature-sensor@49 {
>> +				compatible = "ti,tmp75";
>> +				reg = <0x49>;
>> +			};
>> +		};
>> +
>> +		i2c4_bus70_chn1: i2c@1 {
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +			reg = <0x1>;
>> +
>> +			pcie_zone_temp1: temperature-sensor@48 {
>> +				compatible = "ti,tmp75";
>> +				reg = <0x48>;
>> +			};
>> +			psu0_inlet_temp2: temperature-sensor@49 {
>> +				compatible = "ti,tmp75";
>> +				reg = <0x49>;
>> +			};
>> +		};
>> +
>> +		i2c4_bus70_chn2: i2c@2 {
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +			reg = <0x2>;
>> +
>> +			pcie_zone_temp2: temperature-sensor@48 {
>> +				compatible = "ti,tmp75";
>> +				reg = <0x48>;
>> +			};
>> +			outlet_temp2: temperature-sensor@49 {
>> +				compatible = "ti,tmp75";
>> +				reg = <0x49>;
>> +			};
>> +		};
>> +
>> +		i2c4_bus70_chn3: i2c@3 {
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +			reg = <0x3>;
>> +
>> +			mb_inlet_temp1: temperature-sensor@7c {
>> +				compatible = "microchip,emc1413";
>> +				reg = <0x7c>;
>> +			};
>> +			mb_inlet_temp2: temperature-sensor@4c {
>> +				compatible = "microchip,emc1413";
>> +				reg = <0x4c>;
>> +			};
>> +		};
>> +	};
>> +};
>> +
>> +&i2c5 {
>> +	status = "okay";
>> +
>> +	i2c-mux@70 {
>> +		compatible = "nxp,pca9548";
>> +		#address-cells = <1>;
>> +		#size-cells = <0>;
>> +		reg = <0x70>;
>> +		i2c-mux-idle-disconnect;
>> +	};
>> +};
>> +
>> +&i2c6 {
>> +	status = "okay";
>> +	rtc@51 {
>> +		compatible = "nxp,pcf85063a";
>> +		reg = <0x51>;
>> +	};
>> +};
>> +
>> +&i2c7 {
>> +	status = "okay";
>> +};
>> +
>> +&i2c9 {
>> +	status = "okay";
>> +};
>> +
>> +&i2c11 {
>> +	status = "okay";
>> +};
>> +
>> +&i2c14 {
>> +	status = "okay";
>> +	eeprom@50 {
>> +		compatible = "atmel,24c64";
>> +		reg = <0x50>;
>> +		pagesize = <32>;
>> +	};
>> +
>> +	bmc_ast2600_cpu: temperature-sensor@35 {
>> +		compatible = "ti,tmp175";
>> +		reg = <0x35>;
>> +	};
>> +};
>> +
>> +&adc0 {
>> +	ref_voltage = <2500>;
>> +	status = "okay";
>> +
>> +	pinctrl-names = "default";
>> +	pinctrl-0 = <&pinctrl_adc0_default &pinctrl_adc1_default
>> +		&pinctrl_adc2_default &pinctrl_adc3_default
>> +		&pinctrl_adc4_default &pinctrl_adc5_default
>> +		&pinctrl_adc6_default &pinctrl_adc7_default>;
>> +};
>> +
>> +&adc1 {
>> +	ref_voltage = <2500>;
>> +	status = "okay";
>> +
>> +	pinctrl-names = "default";
>> +	pinctrl-0 = <&pinctrl_adc8_default &pinctrl_adc9_default
>> +		&pinctrl_adc10_default &pinctrl_adc11_default
>> +		&pinctrl_adc12_default &pinctrl_adc13_default
>> +		&pinctrl_adc14_default &pinctrl_adc15_default>;
>> +};
>> +
>> +&vhub {
>> +	status = "okay";
>> +};
>> +
>> +&video {
>> +	status = "okay";
>> +	memory-region = <&video_engine_memory>;
>> +};
>> +
>> +&gpio0 {
>> +	gpio-line-names =
>> +	/*A0-A7*/	"","","","","","i2c2-reset-n","i2c6-reset-n","i2c4-reset-n",
>> +	/*B0-B7*/	"","","","","host0-sysreset-n","host0-pmin-n","","",
>> +	/*C0-C7*/	"s0-vrd-fault-n","s1-vrd-fault-n","bmc-debug-mode","",
> 
> Mildly interested in the functionality of "bmc-debug-mode" :)
> 

This gpio will be removed in next version.

>> +			"irq-n","","vrd-sel","spd-sel",
>> +	/*D0-D7*/	"presence-ps0","presence-ps1","hsc-12vmain-alt2-n","ext-high-temp-n",
>> +			"","bmc-ncsi-txen","","",
> 
> Is "bmc-ncsi-txen" something that should be associated with the MAC?
> 
>> +	/*E0-E7*/	"eth-phy-rst-n","eth-phy-int-n","clk50m-bmc-ncsi","","","","","",
> 
> Same question for eth-phy-rst-n and eth-phy-int-n.
> 
These two gpios will be removed in next version as well

>> +	/*F0-F7*/	"s0-pcp-oc-warn-n","s1-pcp-oc-warn-n","power-chassis-control",
>> +			"cpu-bios-recover","cpld-done","hs-scout-proc-hot",
>> +			"s0-vr-hot-n","s1-vr-hot-n",
>> +	/*G0-G7*/	"","","hsc-12vmain-alt1-n","bmc-salt12-s0-ssif-n","","","","",
>> +	/*H0-H7*/	"","fpga-program-b","wd-disable-n","power-chassis-good","","","","",
>> +	/*I0-I7*/	"","","","","","adc-sw","power-button","rtc-battery-voltage-read-enable",
>> +	/*J0-J7*/	"","","","","","","","",
>> +	/*K0-K7*/	"","","","","","","","",
>> +	/*L0-L7*/	"","","","","","","","",
>> +	/*M0-M7*/	"bmc-uart-cts1","s0-ddr-save","soc-spi-nor-access","presence-cpu0",
>> +			"s0-rtc-lock","","","",
> 
> Why isn't "bmc-uart-cts1" muxed into the associated UART? Why is it a GPIO?
> 
Will remove in next version

>> +	/*N0-N7*/	"hpm-fw-recovery","hpm-stby-rst-n","jtag-sel-s0","led-sw-hb",
>> +			"jtag-dbgr-prsnt-n","","","",
>> +	/*O0-O7*/	"","","","","","","","",
>> +	/*P0-P7*/	"ps0-ac-loss-n","ps1-ac-loss-n","","",
>> +			"led-fault","cpld-user-mode","jtag-srst-n","led-bmc-hb",
>> +	/*Q0-Q7*/	"","","","","","","","",
>> +	/*R0-R7*/	"","","","","","","","",
>> +	/*S0-S7*/	"","","identify-button","led-identify",
>> +			"s1-ddr-save","spi-nor-access","sys-pgood","presence-cpu1",
>> +	/*T0-T7*/	"","","","","","","","",
>> +	/*U0-U7*/	"","","","","","","","",
>> +	/*V0-V7*/	"s0-hightemp-n","s0-fault-alert","s0-sys-auth-failure-n",
>> +			"host0-reboot-ack-n","host0-ready","host0-shd-req-n",
>> +			"host0-shd-ack-n","s0-overtemp-n",
>> +	/*W0-W7*/	"ocp-aux-pwren","ocp-main-pwren","ocp-pgood","",
>> +			"bmc-ok","bmc-ready","spi0-program-sel","spi0-backup-sel",
>> +	/*X0-X7*/	"i2c-backup-sel","s1-fault-alert","s1-fw-boot-ok",
>> +			"s1-hightemp-n","s0-spi-auth-fail-n","s1-sys-auth-failure-n",
>> +			"s1-overtemp-n","cpld-s1-spi-auth-fail-n",
>> +	/*Y0-Y7*/	"","","","","","","bmc-spi-fm-boot-abr-pd","host0-special-boot",
>> +	/*Z0-Z7*/	"reset-button","ps0-pgood","ps1-pgood","","","","","";
>> +};
>> +
>> +&gpio1 {
>> +	gpio-line-names =
>> +	/*18A0-18A7*/	"","","","","","","","",
>> +	/*18B0-18B7*/	"","","","","emmc-rst-n","","s0-soc-pgood","",
> 
> "emmc-rst-n" should be specified as part of mmc-pwrseq-emmc, right?
> 
> https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/mmc/mmc-pwrseq-emmc.yaml?h=v5.19-rc7
> 

Agree, this pin should be part of mmc-pwrseq-emmc and will be removed in 
next version.

Thanks a lot for the comment.
- Quan