* Stable regression 2.6.29.3 vs 2.6.29.2 @ 2009-05-29 19:35 Pascal Terjan 2009-05-29 19:47 ` Rafael J. Wysocki 2009-05-29 19:48 ` Yinghai Lu 0 siblings, 2 replies; 14+ messages in thread From: Pascal Terjan @ 2009-05-29 19:35 UTC (permalink / raw) To: linux-kernel; +Cc: stable, Yinghai Lu (Resending because of wrong To:, sorry for the duplicate) We have a machine here where hard disk is no longer detected at boot time with 2.6.29.3 (it happens only on kernels with HIGHMEM4G + PAE and not on the same one with HIGHMEM64G). Motherboard is ECS PF22 Extreme bisect blames this commit: http://git.kernel.org/?p=linux/kernel/git/stable/linux-2.6.29.y.git;a=commit;h=3b442bfc78d351343fa539c63afde75d7b134316 lspci -vvv: 00:00.0 Host bridge: Intel Corporation 82955X Memory Controller Hub (rev 81) Subsystem: Elitegroup Computer Systems Device 1b75 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Latency: 0 Capabilities: <access denied> 00:01.0 PCI bridge: Intel Corporation 82955X PCI Express Root Port (rev 81) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 00009000-00009fff Memory behind bridge: f7e00000-fdefffff Prefetchable memory behind bridge: 00000000aff00000-00000000efefffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport-driver Kernel modules: shpchp 00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 01) Subsystem: Elitegroup Computer Systems Device 1b75 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 16 Region 0: Memory at febf8000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel 00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (rev 01) (prog-if 00 [Normal decode]) Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 I/O behind bridge: 0000f000-00000fff Memory behind bridge: fff00000-000fffff Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport-driver Kernel modules: shpchp 00:1c.4 PCI bridge: Intel Corporation 82801GR/GH/GHM (ICH7 Family) PCI Express Port 5 (rev 01) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Bus: primary=00, secondary=03, subordinate=03, sec-latency=0 I/O behind bridge: 0000a000-0000afff Memory behind bridge: fdf00000-fe7fffff Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport-driver Kernel modules: shpchp 00:1c.5 PCI bridge: Intel Corporation 82801GR/GH/GHM (ICH7 Family) PCI Express Port 6 (rev 01) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Bus: primary=00, secondary=04, subordinate=04, sec-latency=0 I/O behind bridge: 0000b000-0000bfff Memory behind bridge: fe800000-fe9fffff Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport-driver Kernel modules: shpchp 00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 01) (prog-if 00 [UHCI]) Subsystem: Elitegroup Computer Systems Device 1b75 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 23 Region 4: I/O ports at e080 [size=32] Kernel driver in use: uhci_hcd Kernel modules: uhci-hcd 00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 01) (prog-if 00 [UHCI]) Subsystem: Elitegroup Computer Systems Device 1b75 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 19 Region 4: I/O ports at e000 [size=32] Kernel driver in use: uhci_hcd Kernel modules: uhci-hcd 00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 01) (prog-if 00 [UHCI]) Subsystem: Elitegroup Computer Systems Device 1b75 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin C routed to IRQ 18 Region 4: I/O ports at dc00 [size=32] Kernel driver in use: uhci_hcd Kernel modules: uhci-hcd 00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 01) (prog-if 00 [UHCI]) Subsystem: Elitegroup Computer Systems Device 1b75 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin D routed to IRQ 16 Region 4: I/O ports at d880 [size=32] Kernel driver in use: uhci_hcd Kernel modules: uhci-hcd 00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 01) (prog-if 20 [EHCI]) Subsystem: Elitegroup Computer Systems Device 1b75 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 23 Region 0: Memory at febff800 (32-bit, non-prefetchable) [size=1K] Capabilities: <access denied> Kernel driver in use: ehci_hcd Kernel modules: ehci-hcd 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1) (prog-if 01 [Subtractive decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Bus: primary=00, secondary=05, subordinate=05, sec-latency=32 I/O behind bridge: 0000c000-0000cfff Memory behind bridge: fea00000-feafffff Prefetchable memory behind bridge: 0000000030000000-00000000300fffff Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> 00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01) Subsystem: Elitegroup Computer Systems Device 1b75 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Capabilities: <access denied> Kernel modules: iTCO_wdt, intel-rng 00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 01) (prog-if 8a [Master SecP PriP]) Subsystem: Elitegroup Computer Systems Device 1b75 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 18 Region 0: I/O ports at 01f0 [size=8] Region 1: I/O ports at 03f4 [size=1] Region 2: I/O ports at 0170 [size=8] Region 3: I/O ports at 0374 [size=1] Region 4: I/O ports at ffa0 [size=16] Kernel driver in use: ata_piix Kernel modules: ata_piix, piix 00:1f.2 SATA controller: Intel Corporation 82801GR/GH (ICH7 Family) SATA AHCI Controller (rev 01) (prog-if 01 [AHCI 1.0]) Subsystem: Elitegroup Computer Systems Device 1b75 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 28 Region 0: I/O ports at ec00 [size=8] Region 1: I/O ports at e880 [size=4] Region 2: I/O ports at e800 [size=8] Region 3: I/O ports at e480 [size=4] Region 4: I/O ports at e400 [size=32] Region 5: Memory at febffc00 (32-bit, non-prefetchable) [size=1K] Capabilities: <access denied> Kernel driver in use: ahci Kernel modules: ahci 00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 01) Subsystem: Elitegroup Computer Systems Device 1b75 Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin B routed to IRQ 19 Region 4: I/O ports at 0400 [size=32] Kernel driver in use: i801_smbus Kernel modules: i2c-i801 01:00.0 VGA compatible controller: nVidia Corporation GeForce 9500 GT (rev a1) (prog-if 00 [VGA controller]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 10 Region 0: Memory at fc000000 (32-bit, non-prefetchable) [size=16M] Region 1: Memory at c0000000 (64-bit, prefetchable) [size=512M] Region 3: Memory at fa000000 (64-bit, non-prefetchable) [size=32M] Region 5: I/O ports at 9c00 [size=128] Expansion ROM at fde80000 [disabled] [size=512K] Capabilities: <access denied> Kernel modules: nvidiafb 03:00.0 Ethernet controller: Intel Corporation 82573V Gigabit Ethernet Controller (Copper) (rev 03) Subsystem: Intel Corporation Device 0000 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 29 Region 0: Memory at fe7e0000 (32-bit, non-prefetchable) [size=128K] Region 1: Memory at fe000000 (32-bit, non-prefetchable) [size=4M] Region 2: I/O ports at ac00 [size=32] Capabilities: <access denied> Kernel driver in use: e1000e Kernel modules: e1000e 04:00.0 RAID bus controller: Silicon Image, Inc. SiI 3132 Serial ATA Raid II Controller (rev 01) Subsystem: Elitegroup Computer Systems Device 5308 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 17 Region 0: Memory at fe9ffc00 (64-bit, non-prefetchable) [size=128] Region 2: Memory at fe9f8000 (64-bit, non-prefetchable) [size=16K] Region 4: I/O ports at bc00 [size=128] Expansion ROM at fe900000 [disabled] [size=512K] Capabilities: <access denied> Kernel driver in use: sata_sil24 Kernel modules: sata_sil24 05:04.0 FireWire (IEEE 1394): VIA Technologies, Inc. VT6306 Fire II IEEE 1394 OHCI Link Layer Controller (rev 80) (prog-if 10 [OHCI]) Subsystem: VIA Technologies, Inc. VT6306 Fire II IEEE 1394 OHCI Link Layer Controller Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 (8000ns max), Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 22 Region 0: Memory at feaff800 (32-bit, non-prefetchable) [size=2K] Region 1: I/O ports at cc00 [size=128] Capabilities: <access denied> Kernel driver in use: ohci1394 Kernel modules: ohci1394 05:05.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8169 Gigabit Ethernet (rev 10) Subsystem: Elitegroup Computer Systems Device 1853 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 (8000ns min, 16000ns max), Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 21 Region 0: I/O ports at c800 [size=256] Region 1: Memory at feaff400 (32-bit, non-prefetchable) [size=256] Expansion ROM at 30000000 [disabled] [size=128K] Capabilities: <access denied> Kernel driver in use: r8169 Kernel modules: r8169 ^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: Stable regression 2.6.29.3 vs 2.6.29.2 2009-05-29 19:35 Stable regression 2.6.29.3 vs 2.6.29.2 Pascal Terjan @ 2009-05-29 19:47 ` Rafael J. Wysocki 2009-05-29 19:54 ` Pascal Terjan 2009-06-02 13:26 ` Pascal Terjan 2009-05-29 19:48 ` Yinghai Lu 1 sibling, 2 replies; 14+ messages in thread From: Rafael J. Wysocki @ 2009-05-29 19:47 UTC (permalink / raw) To: Pascal Terjan; +Cc: linux-kernel, stable, Yinghai Lu, Greg KH, Andrew Morton On Friday 29 May 2009, Pascal Terjan wrote: > (Resending because of wrong To:, sorry for the duplicate) > > We have a machine here where hard disk is no longer detected at boot > time with 2.6.29.3 (it happens only on kernels with HIGHMEM4G + PAE and > not on the same one with HIGHMEM64G). > > Motherboard is ECS PF22 Extreme > > bisect blames this commit: > > http://git.kernel.org/?p=linux/kernel/git/stable/linux-2.6.29.y.git;a=commit;h=3b442bfc78d351343fa539c63afde75d7b134316 Would it be possible to check if the current mainline works correctly? Rafael > lspci -vvv: > > 00:00.0 Host bridge: Intel Corporation 82955X Memory Controller Hub (rev > 81) > Subsystem: Elitegroup Computer Systems Device 1b75 > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- > <MAbort+ >SERR- <PERR- INTx- > Latency: 0 > Capabilities: <access denied> > > 00:01.0 PCI bridge: Intel Corporation 82955X PCI Express Root Port (rev > 81) (prog-if 00 [Normal decode]) > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR+ FastB2B- DisINTx+ > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- > <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 32 bytes > Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 > I/O behind bridge: 00009000-00009fff > Memory behind bridge: f7e00000-fdefffff > Prefetchable memory behind bridge: 00000000aff00000-00000000efefffff > Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- > <MAbort- <SERR- <PERR- > BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B- > PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- > Capabilities: <access denied> > Kernel driver in use: pcieport-driver > Kernel modules: shpchp > > 00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High > Definition Audio Controller (rev 01) > Subsystem: Elitegroup Computer Systems Device 1b75 > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- > <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 32 bytes > Interrupt: pin A routed to IRQ 16 > Region 0: Memory at febf8000 (64-bit, non-prefetchable) [size=16K] > Capabilities: <access denied> > Kernel driver in use: HDA Intel > Kernel modules: snd-hda-intel > > 00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express > Port 1 (rev 01) (prog-if 00 [Normal decode]) > Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR+ FastB2B- DisINTx+ > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- > <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 32 bytes > Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 > I/O behind bridge: 0000f000-00000fff > Memory behind bridge: fff00000-000fffff > Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff > Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- > <MAbort+ <SERR- <PERR- > BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B- > PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- > Capabilities: <access denied> > Kernel driver in use: pcieport-driver > Kernel modules: shpchp > > 00:1c.4 PCI bridge: Intel Corporation 82801GR/GH/GHM (ICH7 Family) PCI > Express Port 5 (rev 01) (prog-if 00 [Normal decode]) > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR+ FastB2B- DisINTx+ > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- > <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 32 bytes > Bus: primary=00, secondary=03, subordinate=03, sec-latency=0 > I/O behind bridge: 0000a000-0000afff > Memory behind bridge: fdf00000-fe7fffff > Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff > Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- > <MAbort- <SERR- <PERR- > BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B- > PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- > Capabilities: <access denied> > Kernel driver in use: pcieport-driver > Kernel modules: shpchp > > 00:1c.5 PCI bridge: Intel Corporation 82801GR/GH/GHM (ICH7 Family) PCI > Express Port 6 (rev 01) (prog-if 00 [Normal decode]) > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR+ FastB2B- DisINTx+ > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- > <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 32 bytes > Bus: primary=00, secondary=04, subordinate=04, sec-latency=0 > I/O behind bridge: 0000b000-0000bfff > Memory behind bridge: fe800000-fe9fffff > Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff > Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- > <MAbort- <SERR- <PERR- > BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B- > PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- > Capabilities: <access denied> > Kernel driver in use: pcieport-driver > Kernel modules: shpchp > > 00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI > Controller #1 (rev 01) (prog-if 00 [UHCI]) > Subsystem: Elitegroup Computer Systems Device 1b75 > Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0 > Interrupt: pin A routed to IRQ 23 > Region 4: I/O ports at e080 [size=32] > Kernel driver in use: uhci_hcd > Kernel modules: uhci-hcd > > 00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI > Controller #2 (rev 01) (prog-if 00 [UHCI]) > Subsystem: Elitegroup Computer Systems Device 1b75 > Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0 > Interrupt: pin B routed to IRQ 19 > Region 4: I/O ports at e000 [size=32] > Kernel driver in use: uhci_hcd > Kernel modules: uhci-hcd > > 00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI > Controller #3 (rev 01) (prog-if 00 [UHCI]) > Subsystem: Elitegroup Computer Systems Device 1b75 > Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0 > Interrupt: pin C routed to IRQ 18 > Region 4: I/O ports at dc00 [size=32] > Kernel driver in use: uhci_hcd > Kernel modules: uhci-hcd > > 00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI > Controller #4 (rev 01) (prog-if 00 [UHCI]) > Subsystem: Elitegroup Computer Systems Device 1b75 > Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0 > Interrupt: pin D routed to IRQ 16 > Region 4: I/O ports at d880 [size=32] > Kernel driver in use: uhci_hcd > Kernel modules: uhci-hcd > > 00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI > Controller (rev 01) (prog-if 20 [EHCI]) > Subsystem: Elitegroup Computer Systems Device 1b75 > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0 > Interrupt: pin A routed to IRQ 23 > Region 0: Memory at febff800 (32-bit, non-prefetchable) [size=1K] > Capabilities: <access denied> > Kernel driver in use: ehci_hcd > Kernel modules: ehci-hcd > > 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1) (prog-if > 01 [Subtractive decode]) > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR+ FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- > <MAbort- >SERR- <PERR- INTx- > Latency: 0 > Bus: primary=00, secondary=05, subordinate=05, sec-latency=32 > I/O behind bridge: 0000c000-0000cfff > Memory behind bridge: fea00000-feafffff > Prefetchable memory behind bridge: 0000000030000000-00000000300fffff > Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort+ <SERR- <PERR- > BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B- > PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- > Capabilities: <access denied> > > 00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC > Interface Bridge (rev 01) > Subsystem: Elitegroup Computer Systems Device 1b75 > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0 > Capabilities: <access denied> > Kernel modules: iTCO_wdt, intel-rng > > 00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE > Controller (rev 01) (prog-if 8a [Master SecP PriP]) > Subsystem: Elitegroup Computer Systems Device 1b75 > Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0 > Interrupt: pin A routed to IRQ 18 > Region 0: I/O ports at 01f0 [size=8] > Region 1: I/O ports at 03f4 [size=1] > Region 2: I/O ports at 0170 [size=8] > Region 3: I/O ports at 0374 [size=1] > Region 4: I/O ports at ffa0 [size=16] > Kernel driver in use: ata_piix > Kernel modules: ata_piix, piix > > 00:1f.2 SATA controller: Intel Corporation 82801GR/GH (ICH7 Family) SATA > AHCI Controller (rev 01) (prog-if 01 [AHCI 1.0]) > Subsystem: Elitegroup Computer Systems Device 1b75 > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx+ > Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 0 > Interrupt: pin B routed to IRQ 28 > Region 0: I/O ports at ec00 [size=8] > Region 1: I/O ports at e880 [size=4] > Region 2: I/O ports at e800 [size=8] > Region 3: I/O ports at e480 [size=4] > Region 4: I/O ports at e400 [size=32] > Region 5: Memory at febffc00 (32-bit, non-prefetchable) [size=1K] > Capabilities: <access denied> > Kernel driver in use: ahci > Kernel modules: ahci > > 00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller > (rev 01) > Subsystem: Elitegroup Computer Systems Device 1b75 > Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Interrupt: pin B routed to IRQ 19 > Region 4: I/O ports at 0400 [size=32] > Kernel driver in use: i801_smbus > Kernel modules: i2c-i801 > > 01:00.0 VGA compatible controller: nVidia Corporation GeForce 9500 GT > (rev a1) (prog-if 00 [VGA controller]) > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- > <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 32 bytes > Interrupt: pin A routed to IRQ 10 > Region 0: Memory at fc000000 (32-bit, non-prefetchable) [size=16M] > Region 1: Memory at c0000000 (64-bit, prefetchable) [size=512M] > Region 3: Memory at fa000000 (64-bit, non-prefetchable) [size=32M] > Region 5: I/O ports at 9c00 [size=128] > Expansion ROM at fde80000 [disabled] [size=512K] > Capabilities: <access denied> > Kernel modules: nvidiafb > > 03:00.0 Ethernet controller: Intel Corporation 82573V Gigabit Ethernet > Controller (Copper) (rev 03) > Subsystem: Intel Corporation Device 0000 > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx+ > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- > <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 64 bytes > Interrupt: pin A routed to IRQ 29 > Region 0: Memory at fe7e0000 (32-bit, non-prefetchable) [size=128K] > Region 1: Memory at fe000000 (32-bit, non-prefetchable) [size=4M] > Region 2: I/O ports at ac00 [size=32] > Capabilities: <access denied> > Kernel driver in use: e1000e > Kernel modules: e1000e > > 04:00.0 RAID bus controller: Silicon Image, Inc. SiI 3132 Serial ATA > Raid II Controller (rev 01) > Subsystem: Elitegroup Computer Systems Device 5308 > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- > <MAbort- >SERR- <PERR- INTx- > Latency: 0, Cache Line Size: 32 bytes > Interrupt: pin A routed to IRQ 17 > Region 0: Memory at fe9ffc00 (64-bit, non-prefetchable) [size=128] > Region 2: Memory at fe9f8000 (64-bit, non-prefetchable) [size=16K] > Region 4: I/O ports at bc00 [size=128] > Expansion ROM at fe900000 [disabled] [size=512K] > Capabilities: <access denied> > Kernel driver in use: sata_sil24 > Kernel modules: sata_sil24 > > 05:04.0 FireWire (IEEE 1394): VIA Technologies, Inc. VT6306 Fire II IEEE > 1394 OHCI Link Layer Controller (rev 80) (prog-if 10 [OHCI]) > Subsystem: VIA Technologies, Inc. VT6306 Fire II IEEE 1394 OHCI Link > Layer Controller > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 64 (8000ns max), Cache Line Size: 32 bytes > Interrupt: pin A routed to IRQ 22 > Region 0: Memory at feaff800 (32-bit, non-prefetchable) [size=2K] > Region 1: I/O ports at cc00 [size=128] > Capabilities: <access denied> > Kernel driver in use: ohci1394 > Kernel modules: ohci1394 > > 05:05.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8169 > Gigabit Ethernet (rev 10) > Subsystem: Elitegroup Computer Systems Device 1853 > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- > Stepping- SERR- FastB2B- DisINTx- > Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- INTx- > Latency: 64 (8000ns min, 16000ns max), Cache Line Size: 32 bytes > Interrupt: pin A routed to IRQ 21 > Region 0: I/O ports at c800 [size=256] > Region 1: Memory at feaff400 (32-bit, non-prefetchable) [size=256] > Expansion ROM at 30000000 [disabled] [size=128K] > Capabilities: <access denied> > Kernel driver in use: r8169 > Kernel modules: r8169 ^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: Stable regression 2.6.29.3 vs 2.6.29.2 2009-05-29 19:47 ` Rafael J. Wysocki @ 2009-05-29 19:54 ` Pascal Terjan 2009-05-29 21:32 ` Rafael J. Wysocki 2009-06-02 13:26 ` Pascal Terjan 1 sibling, 1 reply; 14+ messages in thread From: Pascal Terjan @ 2009-05-29 19:54 UTC (permalink / raw) To: Rafael J. Wysocki Cc: linux-kernel, stable, Yinghai Lu, Greg KH, Andrew Morton 2009/5/29 Rafael J. Wysocki <rjw@sisk.pl>: > On Friday 29 May 2009, Pascal Terjan wrote: >> (Resending because of wrong To:, sorry for the duplicate) >> >> We have a machine here where hard disk is no longer detected at boot >> time with 2.6.29.3 (it happens only on kernels with HIGHMEM4G + PAE and >> not on the same one with HIGHMEM64G). >> >> Motherboard is ECS PF22 Extreme >> >> bisect blames this commit: >> >> http://git.kernel.org/?p=linux/kernel/git/stable/linux-2.6.29.y.git;a=commit;h=3b442bfc78d351343fa539c63afde75d7b134316 > > Would it be possible to check if the current mainline works correctly? > I'll do that on Tuesday (the machine is in the office) ^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: Stable regression 2.6.29.3 vs 2.6.29.2 2009-05-29 19:54 ` Pascal Terjan @ 2009-05-29 21:32 ` Rafael J. Wysocki 0 siblings, 0 replies; 14+ messages in thread From: Rafael J. Wysocki @ 2009-05-29 21:32 UTC (permalink / raw) To: Pascal Terjan; +Cc: linux-kernel, stable, Yinghai Lu, Greg KH, Andrew Morton On Friday 29 May 2009, Pascal Terjan wrote: > 2009/5/29 Rafael J. Wysocki <rjw@sisk.pl>: > > On Friday 29 May 2009, Pascal Terjan wrote: > >> (Resending because of wrong To:, sorry for the duplicate) > >> > >> We have a machine here where hard disk is no longer detected at boot > >> time with 2.6.29.3 (it happens only on kernels with HIGHMEM4G + PAE and > >> not on the same one with HIGHMEM64G). > >> > >> Motherboard is ECS PF22 Extreme > >> > >> bisect blames this commit: > >> > >> http://git.kernel.org/?p=linux/kernel/git/stable/linux-2.6.29.y.git;a=commit;h=3b442bfc78d351343fa539c63afde75d7b134316 > > > > Would it be possible to check if the current mainline works correctly? > > > > I'll do that on Tuesday (the machine is in the office) Great, thanks. Rafael ^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: Stable regression 2.6.29.3 vs 2.6.29.2 2009-05-29 19:47 ` Rafael J. Wysocki 2009-05-29 19:54 ` Pascal Terjan @ 2009-06-02 13:26 ` Pascal Terjan 1 sibling, 0 replies; 14+ messages in thread From: Pascal Terjan @ 2009-06-02 13:26 UTC (permalink / raw) To: Rafael J. Wysocki Cc: linux-kernel, stable, Yinghai Lu, Greg KH, Andrew Morton Le vendredi 29 mai 2009 à 21:47 +0200, Rafael J. Wysocki a écrit : > On Friday 29 May 2009, Pascal Terjan wrote: > > (Resending because of wrong To:, sorry for the duplicate) > > > > We have a machine here where hard disk is no longer detected at boot > > time with 2.6.29.3 (it happens only on kernels with HIGHMEM4G + PAE and > > not on the same one with HIGHMEM64G). > > > > Motherboard is ECS PF22 Extreme > > > > bisect blames this commit: > > > > http://git.kernel.org/?p=linux/kernel/git/stable/linux-2.6.29.y.git;a=commit;h=3b442bfc78d351343fa539c63afde75d7b134316 > > Would it be possible to check if the current mainline works correctly? 2.6.30-rc7 has the same issue ^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: Stable regression 2.6.29.3 vs 2.6.29.2 2009-05-29 19:35 Stable regression 2.6.29.3 vs 2.6.29.2 Pascal Terjan 2009-05-29 19:47 ` Rafael J. Wysocki @ 2009-05-29 19:48 ` Yinghai Lu 2009-06-02 13:28 ` Pascal Terjan 1 sibling, 1 reply; 14+ messages in thread From: Yinghai Lu @ 2009-05-29 19:48 UTC (permalink / raw) To: Pascal Terjan; +Cc: linux-kernel, stable Pascal Terjan wrote: > (Resending because of wrong To:, sorry for the duplicate) > > We have a machine here where hard disk is no longer detected at boot > time with 2.6.29.3 (it happens only on kernels with HIGHMEM4G + PAE and > not on the same one with HIGHMEM64G). > > Motherboard is ECS PF22 Extreme > > bisect blames this commit: > > http://git.kernel.org/?p=linux/kernel/git/stable/linux-2.6.29.y.git;a=commit;h=3b442bfc78d351343fa539c63afde75d7b134316 > boot log with debug please. YH ^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: Stable regression 2.6.29.3 vs 2.6.29.2 2009-05-29 19:48 ` Yinghai Lu @ 2009-06-02 13:28 ` Pascal Terjan 2009-06-02 17:24 ` Yinghai Lu 0 siblings, 1 reply; 14+ messages in thread From: Pascal Terjan @ 2009-06-02 13:28 UTC (permalink / raw) To: Yinghai Lu; +Cc: linux-kernel, stable Le vendredi 29 mai 2009 à 12:48 -0700, Yinghai Lu a écrit : > Pascal Terjan wrote: > > (Resending because of wrong To:, sorry for the duplicate) > > > > We have a machine here where hard disk is no longer detected at boot > > time with 2.6.29.3 (it happens only on kernels with HIGHMEM4G + PAE and > > not on the same one with HIGHMEM64G). > > > > Motherboard is ECS PF22 Extreme > > > > bisect blames this commit: > > > > http://git.kernel.org/?p=linux/kernel/git/stable/linux-2.6.29.y.git;a=commit;h=3b442bfc78d351343fa539c63afde75d7b134316 > > > > boot log with debug please. > Linux version 2.6.29.2 (a@qadev1.mandriva.com) (gcc version 4.3.2 (GCC) ) #6 SMP Fri May 29 17:35:31 CEST 2009 KERNEL supported cpus: Intel GenuineIntel AMD AuthenticAMD NSC Geode by NSC Cyrix CyrixInstead Centaur CentaurHauls Transmeta GenuineTMx86 Transmeta TransmetaCPU UMC UMC UMC UMC BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000e6000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000001ffc0000 (usable) BIOS-e820: 000000001ffc0000 - 000000001ffce000 (ACPI data) BIOS-e820: 000000001ffce000 - 000000001fff0000 (ACPI NVS) BIOS-e820: 000000001fff0000 - 0000000020000000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) BIOS-e820: 00000000ffb80000 - 0000000100000000 (reserved) debug: ignoring loglevel setting. DMI 2.3 present. AMI BIOS detected: BIOS may corrupt low RAM, working around it. last_pfn = 0x1ffc0 max_arch_pfn = 0x100000 x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106 kernel direct mapping tables up to 1ffc0000 @ 10000-15000 RAMDISK: 1fc24000 - 1ffaf26f ACPI: RSDP 000F8F60, 0014 (r0 ACPIAM) ACPI: RSDT 1FFC0000, 0038 (r1 A M I OEMRSDT 11000516 MSFT 97) ACPI: FACP 1FFC0200, 0084 (r2 A M I OEMFACP 11000516 MSFT 97) FADT: X_PM1a_EVT_BLK.bit_width (16) does not match PM1_EVT_LEN (4) ACPI: DSDT 1FFC0440, 46B6 (r1 PF PF022 22 INTL 2002026) ACPI: FACS 1FFCE000, 0040 ACPI: APIC 1FFC0390, 006C (r1 A M I OEMAPIC 11000516 MSFT 97) ACPI: MCFG 1FFC0400, 003C (r1 A M I OEMMCFG 11000516 MSFT 97) ACPI: OEMB 1FFCE040, 0046 (r1 A M I AMI_OEM 11000516 MSFT 97) ACPI: ASF! 1FFC4B00, 0099 (r32 LEGEND I865PASF 1 INTL 2002026) ACPI: Local APIC address 0xfee00000 0MB HIGHMEM available. 511MB LOWMEM available. mapped low ram: 0 - 1ffc0000 low ram: 00000000 - 1ffc0000 bootmap 00011000 - 00014ff8 (9 early reservations) ==> bootmem [0000000000 - 001ffc0000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000] #1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000] #2 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 - 0000007000] #3 [0000100000 - 00006399a4] TEXT DATA BSS ==> [0000100000 - 00006399a4] #4 [001fc24000 - 001ffaf26f] RAMDISK ==> [001fc24000 - 001ffaf26f] #5 [000063a000 - 000063d000] INIT_PG_TABLE ==> [000063a000 - 000063d000] #6 [000009e000 - 0000100000] BIOS reserved ==> [000009e000 - 0000100000] #7 [0000010000 - 0000011000] PGTABLE ==> [0000010000 - 0000011000] #8 [0000011000 - 0000015000] BOOTMAP ==> [0000011000 - 0000015000] found SMP MP-table at [c00ff780] 000ff780 Zone PFN ranges: DMA 0x00000010 -> 0x00001000 Normal 0x00001000 -> 0x0001ffc0 HighMem 0x0001ffc0 -> 0x0001ffc0 Movable zone start PFN for each node early_node_map[2] active PFN ranges 0: 0x00000010 -> 0x0000009f 0: 0x00000100 -> 0x0001ffc0 On node 0 totalpages: 130895 free_area_init_node: node 0, pgdat c04eaf80, node_mem_map c1000200 DMA zone: 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 3951 pages, LIFO batch:0 Normal zone: 992 pages used for memmap Normal zone: 125920 pages, LIFO batch:31 Using APIC driver default ACPI: PM-Timer IO Port: 0x808 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled) ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ9 used by override. Enabling APIC mode: Flat. Using 1 I/O APICs Using ACPI (MADT) for SMP configuration information SMP: Allowing 4 CPUs, 2 hotplug CPUs nr_irqs_gsi: 24 PM: Registered nosave memory: 000000000009f000 - 00000000000a0000 PM: Registered nosave memory: 00000000000a0000 - 00000000000e6000 PM: Registered nosave memory: 00000000000e6000 - 0000000000100000 Allocating PCI resources starting at 30000000 (gap: 20000000:dee00000) NR_CPUS:32 nr_cpumask_bits:32 nr_cpu_ids:4 nr_node_ids:1 PERCPU: Allocating 40960 bytes of per cpu data Built 1 zonelists in Zone order, mobility grouping on. Total pages: 129871 Kernel command line: BOOT_IMAGE=2.6.29.2 root=UUID=93e4c48e-2222-47da-a3c5-1f7cf113b05e resume=UUID=227b6318-7827-43c1-93ed-0412eefe016e console=ttyS0,115200 console=tty0 loglevel=8 ignore_loglevel Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 PID hash table entries: 2048 (order: 11, 8192 bytes) Fast TSC calibration using PIT Detected 3215.689 MHz processor. Console: colour VGA+ 80x25 console [tty0] enabled console [ttyS0] enabled Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 509740k/524032k available (2668k kernel code, 13692k reserved, 1575k data, 444k init, 0k highmem) virtual kernel memory layout: fixmap : 0xffe17000 - 0xfffff000 (1952 kB) pkmap : 0xff800000 - 0xffc00000 (4096 kB) vmalloc : 0xe07c0000 - 0xff7fe000 ( 496 MB) lowmem : 0xc0000000 - 0xdffc0000 ( 511 MB) .init : 0xc052c000 - 0xc059b000 ( 444 kB) .data : 0xc039b065 - 0xc0524f08 (1575 kB) .text : 0xc0100000 - 0xc039b065 (2668 kB) Checking if this processor honours the WP bit even in supervisor mode...Ok. SLUB: Genslabs=12, HWalign=128, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 Calibrating delay loop (skipped), value calculated using timer frequency.. 6431.37 BogoMIPS (lpj=3215689) Security Framework initialized Mount-cache hash table entries: 512 CPU: Trace cache: 12K uops, L1 D cache: 16K CPU: L2 cache: 1024K CPU: Physical Processor ID: 0 CPU: Processor Core ID: 0 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU0: Intel P4/Xeon Extended MCE MSRs (24) available CPU0: Thermal monitoring enabled using mwait in idle threads. Checking 'hlt' instruction... OK. ACPI: Core revision 20081204 ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 CPU0: Intel(R) Pentium(R) D CPU 3.20GHz stepping 04 Booting processor 1 APIC 0x1 ip 0x6000 Initializing CPU#1 Calibrating delay using timer specific routine.. 6429.86 BogoMIPS (lpj=3214932) CPU: Trace cache: 12K uops, L1 D cache: 16K CPU: L2 cache: 1024K CPU: Physical Processor ID: 0 CPU: Processor Core ID: 1 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#1. CPU1: Intel P4/Xeon Extended MCE MSRs (24) available CPU1: Thermal monitoring enabled x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106 CPU1: Intel(R) Pentium(R) D CPU 3.20GHz stepping 04 checking TSC synchronization [CPU#0 -> CPU#1]: Measured 900283104 cycles TSC warp between CPUs, turning off TSC clock. Marking TSC unstable due to check_tsc_sync_source failed Brought up 2 CPUs Total of 2 processors activated (12861.24 BogoMIPS). CPU0 attaching sched-domain: domain 0: span 0-1 level CPU groups: 0 1 CPU1 attaching sched-domain: domain 0: span 0-1 level CPU groups: 1 0 net_namespace: 1056 bytes Booting paravirtualized kernel on bare hardware Time: 15:34:36 Date: 06/02/09 NET: Registered protocol family 16 ACPI: bus type pci registered PCI: MCFG configuration 0: base f0000000 segment 0 buses 0 - 255 PCI: Not using MMCONFIG. PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=5 PCI: Using configuration type 1 for base access bio: create slab <bio-0> at 0 ACPI: EC: Look up EC in DSDT ACPI: Interpreter enabled ACPI: (supports S0 S1 S3 S4 S5) ACPI: Using IOAPIC for interrupt routing PCI: MCFG configuration 0: base f0000000 segment 0 buses 0 - 255 PCI: MCFG area at f0000000 reserved in ACPI motherboard resources PCI: Using MMCONFIG for extended config space ACPI: No dock devices found. ACPI: PCI Root Bridge [PCI0] (0000:00) pci 0000:00:01.0: PME# supported from D0 D3hot D3cold pci 0000:00:01.0: PME# disabled pci 0000:00:1b.0: reg 10 64bit mmio: [0xfebf8000-0xfebfbfff] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold pci 0000:00:1b.0: PME# disabled pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold pci 0000:00:1c.0: PME# disabled pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold pci 0000:00:1c.4: PME# disabled pci 0000:00:1c.5: PME# supported from D0 D3hot D3cold pci 0000:00:1c.5: PME# disabled pci 0000:00:1d.0: reg 20 io port: [0xe080-0xe09f] pci 0000:00:1d.1: reg 20 io port: [0xe000-0xe01f] pci 0000:00:1d.2: reg 20 io port: [0xdc00-0xdc1f] pci 0000:00:1d.3: reg 20 io port: [0xd880-0xd89f] pci 0000:00:1d.7: reg 10 32bit mmio: [0xfebff800-0xfebffbff] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold pci 0000:00:1d.7: PME# disabled pci 0000:00:1f.0: Force enabled HPET at 0xfed00000 pci 0000:00:1f.0: quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO pci 0000:00:1f.0: quirk: region 0480-04bf claimed by ICH6 GPIO pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0a00 (mask 00ff) pci 0000:00:1f.0: ICH7 LPC Generic IO decode 2 PIO at 0290 (mask 00ff) pci 0000:00:1f.1: reg 10 io port: [0x00-0x07] pci 0000:00:1f.1: reg 14 io port: [0x00-0x03] pci 0000:00:1f.1: reg 18 io port: [0x00-0x07] pci 0000:00:1f.1: reg 1c io port: [0x00-0x03] pci 0000:00:1f.1: reg 20 io port: [0xffa0-0xffaf] pci 0000:00:1f.2: reg 10 io port: [0xec00-0xec07] pci 0000:00:1f.2: reg 14 io port: [0xe880-0xe883] pci 0000:00:1f.2: reg 18 io port: [0xe800-0xe807] pci 0000:00:1f.2: reg 1c io port: [0xe480-0xe483] pci 0000:00:1f.2: reg 20 io port: [0xe400-0xe41f] pci 0000:00:1f.2: reg 24 32bit mmio: [0xfebffc00-0xfebfffff] pci 0000:00:1f.2: PME# supported from D3hot pci 0000:00:1f.2: PME# disabled pci 0000:00:1f.3: reg 20 io port: [0x400-0x41f] pci 0000:01:00.0: reg 10 32bit mmio: [0xfc000000-0xfcffffff] pci 0000:01:00.0: reg 14 64bit mmio: [0xc0000000-0xdfffffff] pci 0000:01:00.0: reg 1c 64bit mmio: [0xfa000000-0xfbffffff] pci 0000:01:00.0: reg 24 io port: [0x9c00-0x9c7f] pci 0000:01:00.0: reg 30 32bit mmio: [0xfde80000-0xfdefffff] pci 0000:00:01.0: bridge io port: [0x9000-0x9fff] pci 0000:00:01.0: bridge 32bit mmio: [0xf7e00000-0xfdefffff] pci 0000:00:01.0: bridge 64bit mmio pref: [0xaff00000-0xefefffff] pci 0000:03:00.0: reg 10 32bit mmio: [0xfe7e0000-0xfe7fffff] pci 0000:03:00.0: reg 14 32bit mmio: [0xfe000000-0xfe3fffff] pci 0000:03:00.0: reg 18 io port: [0xac00-0xac1f] pci 0000:03:00.0: PME# supported from D0 D3hot D3cold pci 0000:03:00.0: PME# disabled pci 0000:03:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force' pci 0000:00:1c.4: bridge io port: [0xa000-0xafff] pci 0000:00:1c.4: bridge 32bit mmio: [0xfdf00000-0xfe7fffff] pci 0000:04:00.0: reg 10 64bit mmio: [0xfe9ffc00-0xfe9ffc7f] pci 0000:04:00.0: reg 18 64bit mmio: [0xfe9f8000-0xfe9fbfff] pci 0000:04:00.0: reg 20 io port: [0xbc00-0xbc7f] pci 0000:04:00.0: reg 30 32bit mmio: [0xfe900000-0xfe97ffff] pci 0000:04:00.0: supports D1 D2 pci 0000:04:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force' pci 0000:00:1c.5: bridge io port: [0xb000-0xbfff] pci 0000:00:1c.5: bridge 32bit mmio: [0xfe800000-0xfe9fffff] pci 0000:05:04.0: reg 10 32bit mmio: [0xfeaff800-0xfeafffff] pci 0000:05:04.0: reg 14 io port: [0xcc00-0xcc7f] pci 0000:05:04.0: supports D2 pci 0000:05:04.0: PME# supported from D2 D3hot D3cold pci 0000:05:04.0: PME# disabled pci 0000:05:05.0: reg 10 io port: [0xc800-0xc8ff] pci 0000:05:05.0: reg 14 32bit mmio: [0xfeaff400-0xfeaff4ff] pci 0000:05:05.0: reg 30 32bit mmio: [0xfeac0000-0xfeadffff] pci 0000:05:05.0: supports D1 D2 pci 0000:05:05.0: PME# supported from D1 D2 D3hot D3cold pci 0000:05:05.0: PME# disabled pci 0000:00:1e.0: transparent bridge pci 0000:00:1e.0: bridge io port: [0xc000-0xcfff] pci 0000:00:1e.0: bridge 32bit mmio: [0xfea00000-0xfeafffff] pci_bus 0000:00: on NUMA node 0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P8._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P9._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 7 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 *5 6 7 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 *5 6 7 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 11 12 14 *15) ACPI Warning (tbutils-0242): Incorrect checksum in table [OEMB] - F6, should be F1 [20081204] PCI: Using ACPI for IRQ routing NetLabel: Initializing NetLabel: domain hash size = 128 NetLabel: protocols = UNLABELED CIPSOv4 NetLabel: unlabeled traffic allowed by default hpet clockevent registered HPET: 3 timers in total, 0 timers will be used for per-cpu timer hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0 hpet0: 3 comparators, 64-bit 14.318180 MHz counter Switched to high resolution mode on CPU 0 Switched to high resolution mode on CPU 1 pnp: PnP ACPI init ACPI: bus type pnp registered pnp: PnP ACPI: found 16 devices ACPI: ACPI bus type pnp unregistered PnPBIOS: Disabled by ACPI PNP system 00:01: iomem range 0xfed13000-0xfed19fff has been reserved system 00:07: ioport range 0x200-0x207 has been reserved system 00:07: ioport range 0x4d0-0x4d1 has been reserved system 00:07: ioport range 0x800-0x87f has been reserved system 00:07: ioport range 0x480-0x4bf has been reserved system 00:07: iomem range 0xfed1c000-0xfed1ffff has been reserved system 00:07: iomem range 0xfed20000-0xfed8ffff has been reserved system 00:09: iomem range 0xffc00000-0xfff7ffff has been reserved system 00:0a: iomem range 0xfec00000-0xfec00fff has been reserved system 00:0a: iomem range 0xfee00000-0xfee00fff has been reserved system 00:0c: ioport range 0xa00-0xa0f has been reserved system 00:0c: ioport range 0x290-0x29f has been reserved system 00:0e: iomem range 0xf0000000-0xf3ffffff has been reserved system 00:0f: iomem range 0x0-0x9ffff could not be reserved system 00:0f: iomem range 0xc0000-0xcffff could not be reserved system 00:0f: iomem range 0xe0000-0xfffff could not be reserved system 00:0f: iomem range 0x100000-0x1fffffff could not be reserved pci 0000:00:01.0: PCI bridge, secondary bus 0000:01 pci 0000:00:01.0: IO window: 0x9000-0x9fff pci 0000:00:01.0: MEM window: 0xf7e00000-0xfdefffff pci 0000:00:01.0: PREFETCH window: 0x000000aff00000-0x000000efefffff pci 0000:00:1c.0: PCI bridge, secondary bus 0000:02 pci 0000:00:1c.0: IO window: disabled pci 0000:00:1c.0: MEM window: disabled pci 0000:00:1c.0: PREFETCH window: disabled pci 0000:00:1c.4: PCI bridge, secondary bus 0000:03 pci 0000:00:1c.4: IO window: 0xa000-0xafff pci 0000:00:1c.4: MEM window: 0xfdf00000-0xfe7fffff pci 0000:00:1c.4: PREFETCH window: disabled pci 0000:00:1c.5: PCI bridge, secondary bus 0000:04 pci 0000:00:1c.5: IO window: 0xb000-0xbfff pci 0000:00:1c.5: MEM window: 0xfe800000-0xfe9fffff pci 0000:00:1c.5: PREFETCH window: disabled pci 0000:00:1e.0: PCI bridge, secondary bus 0000:05 pci 0000:00:1e.0: IO window: 0xc000-0xcfff pci 0000:00:1e.0: MEM window: 0xfea00000-0xfeafffff pci 0000:00:1e.0: PREFETCH window: 0x00000030000000-0x000000300fffff pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 pci 0000:00:01.0: setting latency timer to 64 pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 pci 0000:00:1c.0: setting latency timer to 64 pci 0000:00:1c.4: PCI INT A -> GSI 16 (level, low) -> IRQ 16 pci 0000:00:1c.4: setting latency timer to 64 pci 0000:00:1c.5: PCI INT B -> GSI 17 (level, low) -> IRQ 17 pci 0000:00:1c.5: setting latency timer to 64 pci 0000:00:1e.0: setting latency timer to 64 pci_bus 0000:00: resource 0 io: [0x00-0xffff] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff] pci_bus 0000:01: resource 0 io: [0x9000-0x9fff] pci_bus 0000:01: resource 1 mem: [0xf7e00000-0xfdefffff] pci_bus 0000:01: resource 2 mem: [0xaff00000-0xefefffff] pci_bus 0000:01: resource 3 mem: [0x0-0x0] pci_bus 0000:02: resource 0 mem: [0x0-0x0] pci_bus 0000:02: resource 1 mem: [0x0-0x0] pci_bus 0000:02: resource 2 mem: [0x0-0x0] pci_bus 0000:02: resource 3 mem: [0x0-0x0] pci_bus 0000:03: resource 0 io: [0xa000-0xafff] pci_bus 0000:03: resource 1 mem: [0xfdf00000-0xfe7fffff] pci_bus 0000:03: resource 2 mem: [0x0-0x0] pci_bus 0000:03: resource 3 mem: [0x0-0x0] pci_bus 0000:04: resource 0 io: [0xb000-0xbfff] pci_bus 0000:04: resource 1 mem: [0xfe800000-0xfe9fffff] pci_bus 0000:04: resource 2 mem: [0x0-0x0] pci_bus 0000:04: resource 3 mem: [0x0-0x0] pci_bus 0000:05: resource 0 io: [0xc000-0xcfff] pci_bus 0000:05: resource 1 mem: [0xfea00000-0xfeafffff] pci_bus 0000:05: resource 2 mem: [0x30000000-0x300fffff] pci_bus 0000:05: resource 3 io: [0x00-0xffff] pci_bus 0000:05: resource 4 mem: [0x000000-0xffffffff] NET: Registered protocol family 2 IP route cache hash table entries: 4096 (order: 2, 16384 bytes) TCP established hash table entries: 16384 (order: 5, 131072 bytes) TCP bind hash table entries: 16384 (order: 5, 131072 bytes) TCP: Hash tables configured (established 16384 bind 16384) TCP reno registered NET: Registered protocol family 1 checking if image is initramfs... it is Freeing initrd memory: 3628k freed apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac) apm: disabled - APM is not SMP safe. audit: initializing netlink socket (disabled) type=2000 audit(1243956876.066:1): initialized HugeTLB registered 4 MB page size, pre-allocated 0 pages VFS: Disk quotas dquot_6.5.2 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) msgmni has been set to 1002 alg: No test for stdrng (krng) Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) pci 0000:01:00.0: Boot video device pcieport-driver 0000:00:01.0: setting latency timer to 64 pcieport-driver 0000:00:01.0: irq 24 for MSI/MSI-X pcieport-driver 0000:00:1c.0: setting latency timer to 64 pcieport-driver 0000:00:1c.0: irq 25 for MSI/MSI-X pcieport-driver 0000:00:1c.4: setting latency timer to 64 pcieport-driver 0000:00:1c.4: irq 26 for MSI/MSI-X pcieport-driver 0000:00:1c.5: setting latency timer to 64 pcieport-driver 0000:00:1c.5: irq 27 for MSI/MSI-X isapnp: Scanning for PnP cards... Clocksource tsc unstable (delta = 279929363 ns) isapnp: No Plug & Play device found Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 00:0d: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A brd: module loaded PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1 PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp serio: i8042 KBD port at 0x60,0x64 irq 1 mice: PS/2 mouse device common for all mice cpuidle: using governor ladder cpuidle: using governor menu TCP cubic registered Using IPI No-Shortcut mode input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0 PM: Resume from partition UUID=227b6318-7827-43c1-93ed-0412eefe016e PM: Checking hibernation image. PM: Error -6 checking image file PM: Resume from disk failed. registered taskstats version 1 Magic number: 13:767:587 BIOS EDD facility v0.16 2004-Jun-25, 1 devices found Freeing unused kernel memory: 444k freed Intel(R) Gigabit Ethernet Network Driver - version 1.2.45-k2 Copyright (c) 2008 Intel Corporation. SCSI subsystem initialized Driver 'sd' needs updating - please use bus_type methods libata version 3.00 loaded. ahci 0000:00:1f.2: version 3.0 ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19 ahci 0000:00:1f.2: BAR 5: can't reserve mem region [0xfebffc00-0xfebfffff] ahci: probe of 0000:00:1f.2 failed with error -16 ata_piix 0000:00:1f.1: version 2.12 ata_piix 0000:00:1f.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18 ata_piix 0000:00:1f.1: setting latency timer to 64 scsi0 : ata_piix scsi1 : ata_piix ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14 ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15 ata1.00: ATAPI: HL-DT-ST DVDRAM GSA-4160B, A302, max UDMA/66 ata1.00: configured for UDMA/66 scsi 0:0:0:0: CD-ROM HL-DT-ST DVDRAM GSA-4160B A302 PQ: 0 ANSI: 5 ata2: port disabled. ignoring. sata_sil24 0000:04:00.0: version 1.1 sata_sil24 0000:04:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 sata_sil24 0000:04:00.0: BAR 0: can't reserve mem region [0xfe9ffc00-0xfe9ffc7f] sata_sil24 0000:04:00.0: PCI INT A disabled sata_sil24: probe of 0000:04:00.0 failed with error -16 ohci1394 0000:05:04.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 ohci1394: MMIO resource (0xfeaff800 - 0xfeb00000) unavailable ohci1394: probe of 0000:05:04.0 failed with error -12 ^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: Stable regression 2.6.29.3 vs 2.6.29.2 2009-06-02 13:28 ` Pascal Terjan @ 2009-06-02 17:24 ` Yinghai Lu 2009-06-02 19:09 ` Pascal Terjan 0 siblings, 1 reply; 14+ messages in thread From: Yinghai Lu @ 2009-06-02 17:24 UTC (permalink / raw) To: Pascal Terjan; +Cc: linux-kernel, stable Pascal Terjan wrote: > Le vendredi 29 mai 2009 à 12:48 -0700, Yinghai Lu a écrit : >> Pascal Terjan wrote: >>> (Resending because of wrong To:, sorry for the duplicate) >>> >>> We have a machine here where hard disk is no longer detected at boot >>> time with 2.6.29.3 (it happens only on kernels with HIGHMEM4G + PAE and >>> not on the same one with HIGHMEM64G). >>> >>> Motherboard is ECS PF22 Extreme >>> >>> bisect blames this commit: >>> >>> http://git.kernel.org/?p=linux/kernel/git/stable/linux-2.6.29.y.git;a=commit;h=3b442bfc78d351343fa539c63afde75d7b134316 >>> >> boot log with debug please. >> > > Linux version 2.6.29.2 (a@qadev1.mandriva.com) (gcc version 4.3.2 > (GCC) ) #6 SMP Fri May 29 17:35:31 CEST 2009 > KERNEL supported cpus: > Intel GenuineIntel > AMD AuthenticAMD > NSC Geode by NSC > Cyrix CyrixInstead > Centaur CentaurHauls > Transmeta GenuineTMx86 > Transmeta TransmetaCPU > UMC UMC UMC UMC > BIOS-provided physical RAM map: > BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) > BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) > BIOS-e820: 00000000000e6000 - 0000000000100000 (reserved) > BIOS-e820: 0000000000100000 - 000000001ffc0000 (usable) > BIOS-e820: 000000001ffc0000 - 000000001ffce000 (ACPI data) > BIOS-e820: 000000001ffce000 - 000000001fff0000 (ACPI NVS) > BIOS-e820: 000000001fff0000 - 0000000020000000 (reserved) > BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) > BIOS-e820: 00000000ffb80000 - 0000000100000000 (reserved) ... > ACPI: bus type pci registered > PCI: MCFG configuration 0: base f0000000 segment 0 buses 0 - 255 > PCI: Not using MMCONFIG. > PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=5 > PCI: Using configuration type 1 for base access > bio: create slab <bio-0> at 0 > ACPI: EC: Look up EC in DSDT > ACPI: Interpreter enabled > ACPI: (supports S0 S1 S3 S4 S5) > ACPI: Using IOAPIC for interrupt routing > PCI: MCFG configuration 0: base f0000000 segment 0 buses 0 - 255 > PCI: MCFG area at f0000000 reserved in ACPI motherboard resources > PCI: Using MMCONFIG for extended config space > pci 0000:00:1d.7: reg 10 32bit mmio: [0xfebff800-0xfebffbff] > pci 0000:00:1f.2: reg 24 32bit mmio: [0xfebffc00-0xfebfffff] > pci 0000:01:00.0: reg 10 32bit mmio: [0xfc000000-0xfcffffff] > pci 0000:01:00.0: reg 1c 64bit mmio: [0xfa000000-0xfbffffff] > pci 0000:01:00.0: reg 30 32bit mmio: [0xfde80000-0xfdefffff] > pci 0000:00:01.0: bridge 32bit mmio: [0xf7e00000-0xfdefffff] > pci 0000:03:00.0: reg 10 32bit mmio: [0xfe7e0000-0xfe7fffff] > pci 0000:03:00.0: reg 14 32bit mmio: [0xfe000000-0xfe3fffff] > pci 0000:00:1c.4: bridge 32bit mmio: [0xfdf00000-0xfe7fffff] > pci 0000:04:00.0: reg 10 64bit mmio: [0xfe9ffc00-0xfe9ffc7f] > pci 0000:04:00.0: reg 18 64bit mmio: [0xfe9f8000-0xfe9fbfff] > pci 0000:04:00.0: reg 30 32bit mmio: [0xfe900000-0xfe97ffff] > pci 0000:05:05.0: reg 14 32bit mmio: [0xfeaff400-0xfeaff4ff] > pci 0000:05:05.0: reg 30 32bit mmio: [0xfeac0000-0xfeadffff] > pci 0000:00:1e.0: bridge 32bit mmio: [0xfea00000-0xfeafffff] > PnPBIOS: Disabled by ACPI PNP > system 00:01: iomem range 0xfed13000-0xfed19fff has been reserved > system 00:07: iomem range 0xfed1c000-0xfed1ffff has been reserved > system 00:07: iomem range 0xfed20000-0xfed8ffff has been reserved > system 00:09: iomem range 0xffc00000-0xfff7ffff has been reserved > system 00:0a: iomem range 0xfec00000-0xfec00fff has been reserved > system 00:0a: iomem range 0xfee00000-0xfee00fff has been reserved > system 00:0e: iomem range 0xf0000000-0xf3ffffff has been reserved > system 00:0f: iomem range 0x100000-0x1fffffff could not be reserved > ahci 0000:00:1f.2: version 3.0 > ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19 > ahci 0000:00:1f.2: BAR 5: can't reserve mem region > [0xfebffc00-0xfebfffff] > ahci: probe of 0000:00:1f.2 failed with error -16 > scsi0 : ata_piix > scsi1 : ata_piix > sata_sil24 0000:04:00.0: version 1.1 > sata_sil24 0000:04:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 > sata_sil24 0000:04:00.0: BAR 0: can't reserve mem region > [0xfe9ffc00-0xfe9ffc7f] > sata_sil24 0000:04:00.0: PCI INT A disabled > sata_sil24: probe of 0000:04:00.0 failed with error -16 > ohci1394 0000:05:04.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 > ohci1394: MMIO resource (0xfeaff800 - 0xfeb00000) unavailable > ohci1394: probe of 0000:05:04.0 failed with error -12 ... looks like MMCONFIG get enabled somehow with that patch. it should not be used [0xf0000000 - 0xffffffff] for bus [0,0xff] can you check if the mmconf was enabled with previous version? YH ^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: Stable regression 2.6.29.3 vs 2.6.29.2 2009-06-02 17:24 ` Yinghai Lu @ 2009-06-02 19:09 ` Pascal Terjan 2009-06-02 20:44 ` Yinghai Lu 0 siblings, 1 reply; 14+ messages in thread From: Pascal Terjan @ 2009-06-02 19:09 UTC (permalink / raw) To: Yinghai Lu; +Cc: linux-kernel, stable Le mardi 02 juin 2009 à 10:24 -0700, Yinghai Lu a écrit : > Pascal Terjan wrote: > > Le vendredi 29 mai 2009 à 12:48 -0700, Yinghai Lu a écrit : > >> Pascal Terjan wrote: > >>> (Resending because of wrong To:, sorry for the duplicate) > >>> > >>> We have a machine here where hard disk is no longer detected at boot > >>> time with 2.6.29.3 (it happens only on kernels with HIGHMEM4G + PAE and > >>> not on the same one with HIGHMEM64G). > >>> > >>> Motherboard is ECS PF22 Extreme > >>> > >>> bisect blames this commit: > >>> > >>> http://git.kernel.org/?p=linux/kernel/git/stable/linux-2.6.29.y.git;a=commit;h=3b442bfc78d351343fa539c63afde75d7b134316 > >>> > >> boot log with debug please. > >> > > > > Linux version 2.6.29.2 (a@qadev1.mandriva.com) (gcc version 4.3.2 > > (GCC) ) #6 SMP Fri May 29 17:35:31 CEST 2009 > > KERNEL supported cpus: > > Intel GenuineIntel > > AMD AuthenticAMD > > NSC Geode by NSC > > Cyrix CyrixInstead > > Centaur CentaurHauls > > Transmeta GenuineTMx86 > > Transmeta TransmetaCPU > > UMC UMC UMC UMC > > BIOS-provided physical RAM map: > > BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) > > BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) > > BIOS-e820: 00000000000e6000 - 0000000000100000 (reserved) > > BIOS-e820: 0000000000100000 - 000000001ffc0000 (usable) > > BIOS-e820: 000000001ffc0000 - 000000001ffce000 (ACPI data) > > BIOS-e820: 000000001ffce000 - 000000001fff0000 (ACPI NVS) > > BIOS-e820: 000000001fff0000 - 0000000020000000 (reserved) > > BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) > > BIOS-e820: 00000000ffb80000 - 0000000100000000 (reserved) > ... > > ACPI: bus type pci registered > > PCI: MCFG configuration 0: base f0000000 segment 0 buses 0 - 255 > > PCI: Not using MMCONFIG. > > PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=5 > > PCI: Using configuration type 1 for base access > > bio: create slab <bio-0> at 0 > > ACPI: EC: Look up EC in DSDT > > ACPI: Interpreter enabled > > ACPI: (supports S0 S1 S3 S4 S5) > > ACPI: Using IOAPIC for interrupt routing > > PCI: MCFG configuration 0: base f0000000 segment 0 buses 0 - 255 > > PCI: MCFG area at f0000000 reserved in ACPI motherboard resources > > PCI: Using MMCONFIG for extended config space > > pci 0000:00:1d.7: reg 10 32bit mmio: [0xfebff800-0xfebffbff] > > pci 0000:00:1f.2: reg 24 32bit mmio: [0xfebffc00-0xfebfffff] > > pci 0000:01:00.0: reg 10 32bit mmio: [0xfc000000-0xfcffffff] > > pci 0000:01:00.0: reg 1c 64bit mmio: [0xfa000000-0xfbffffff] > > pci 0000:01:00.0: reg 30 32bit mmio: [0xfde80000-0xfdefffff] > > pci 0000:00:01.0: bridge 32bit mmio: [0xf7e00000-0xfdefffff] > > pci 0000:03:00.0: reg 10 32bit mmio: [0xfe7e0000-0xfe7fffff] > > pci 0000:03:00.0: reg 14 32bit mmio: [0xfe000000-0xfe3fffff] > > pci 0000:00:1c.4: bridge 32bit mmio: [0xfdf00000-0xfe7fffff] > > pci 0000:04:00.0: reg 10 64bit mmio: [0xfe9ffc00-0xfe9ffc7f] > > pci 0000:04:00.0: reg 18 64bit mmio: [0xfe9f8000-0xfe9fbfff] > > pci 0000:04:00.0: reg 30 32bit mmio: [0xfe900000-0xfe97ffff] > > pci 0000:05:05.0: reg 14 32bit mmio: [0xfeaff400-0xfeaff4ff] > > pci 0000:05:05.0: reg 30 32bit mmio: [0xfeac0000-0xfeadffff] > > pci 0000:00:1e.0: bridge 32bit mmio: [0xfea00000-0xfeafffff] > > > PnPBIOS: Disabled by ACPI PNP > > system 00:01: iomem range 0xfed13000-0xfed19fff has been reserved > > system 00:07: iomem range 0xfed1c000-0xfed1ffff has been reserved > > system 00:07: iomem range 0xfed20000-0xfed8ffff has been reserved > > system 00:09: iomem range 0xffc00000-0xfff7ffff has been reserved > > system 00:0a: iomem range 0xfec00000-0xfec00fff has been reserved > > system 00:0a: iomem range 0xfee00000-0xfee00fff has been reserved > > system 00:0e: iomem range 0xf0000000-0xf3ffffff has been reserved > > system 00:0f: iomem range 0x100000-0x1fffffff could not be reserved > > > ahci 0000:00:1f.2: version 3.0 > > ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19 > > ahci 0000:00:1f.2: BAR 5: can't reserve mem region > > [0xfebffc00-0xfebfffff] > > ahci: probe of 0000:00:1f.2 failed with error -16 > > scsi0 : ata_piix > > scsi1 : ata_piix > > sata_sil24 0000:04:00.0: version 1.1 > > sata_sil24 0000:04:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 > > sata_sil24 0000:04:00.0: BAR 0: can't reserve mem region > > [0xfe9ffc00-0xfe9ffc7f] > > sata_sil24 0000:04:00.0: PCI INT A disabled > > sata_sil24: probe of 0000:04:00.0 failed with error -16 > > ohci1394 0000:05:04.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 > > ohci1394: MMIO resource (0xfeaff800 - 0xfeb00000) unavailable > > ohci1394: probe of 0000:05:04.0 failed with error -12 > ... > > looks like MMCONFIG get enabled somehow with that patch. > it should not be used [0xf0000000 - 0xffffffff] for bus [0,0xff] > > can you check if the mmconf was enabled with previous version? It seems so The first difference I notice in the log is that kernel without the patch gets this line: PCI: updated MCFG configuration 0: base f0000000 segment 0 buses 0 - 63 Here is full log: Linux version 2.6.29.2 (a@qadev1.mandriva.com) (gcc version 4.3.2 (GCC) ) #8 SMP Tue Jun 2 20:42:29 CEST 2009 KERNEL supported cpus: Intel GenuineIntel AMD AuthenticAMD NSC Geode by NSC Cyrix CyrixInstead Centaur CentaurHauls Transmeta GenuineTMx86 Transmeta TransmetaCPU UMC UMC UMC UMC BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000e6000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000001ffc0000 (usable) BIOS-e820: 000000001ffc0000 - 000000001ffce000 (ACPI data) BIOS-e820: 000000001ffce000 - 000000001fff0000 (ACPI NVS) BIOS-e820: 000000001fff0000 - 0000000020000000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) BIOS-e820: 00000000ffb80000 - 0000000100000000 (reserved) DMI 2.3 present. AMI BIOS detected: BIOS may corrupt low RAM, working around it. last_pfn = 0x1ffc0 max_arch_pfn = 0x100000 x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106 kernel direct mapping tables up to 1ffc0000 @ 10000-15000 RAMDISK: 1fc2f000 - 1ffaf412 ACPI: RSDP 000F8F60, 0014 (r0 ACPIAM) ACPI: RSDT 1FFC0000, 0038 (r1 A M I OEMRSDT 11000516 MSFT 97) ACPI: FACP 1FFC0200, 0084 (r2 A M I OEMFACP 11000516 MSFT 97) FADT: X_PM1a_EVT_BLK.bit_width (16) does not match PM1_EVT_LEN (4) ACPI: DSDT 1FFC0440, 46B6 (r1 PF PF022 22 INTL 2002026) ACPI: FACS 1FFCE000, 0040 ACPI: APIC 1FFC0390, 006C (r1 A M I OEMAPIC 11000516 MSFT 97) ACPI: MCFG 1FFC0400, 003C (r1 A M I OEMMCFG 11000516 MSFT 97) ACPI: OEMB 1FFCE040, 0046 (r1 A M I AMI_OEM 11000516 MSFT 97) ACPI: ASF! 1FFC4B00, 0099 (r32 LEGEND I865PASF 1 INTL 2002026) ACPI: Local APIC address 0xfee00000 0MB HIGHMEM available. 511MB LOWMEM available. mapped low ram: 0 - 1ffc0000 low ram: 00000000 - 1ffc0000 bootmap 00011000 - 00014ff8 (9 early reservations) ==> bootmem [0000000000 - 001ffc0000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000] #1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000] #2 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 - 0000007000] #3 [0000100000 - 0000641c24] TEXT DATA BSS ==> [0000100000 - 0000641c24] #4 [001fc2f000 - 001ffaf412] RAMDISK ==> [001fc2f000 - 001ffaf412] #5 [0000642000 - 0000645000] INIT_PG_TABLE ==> [0000642000 - 0000645000] #6 [000009e000 - 0000100000] BIOS reserved ==> [000009e000 - 0000100000] #7 [0000010000 - 0000011000] PGTABLE ==> [0000010000 - 0000011000] #8 [0000011000 - 0000015000] BOOTMAP ==> [0000011000 - 0000015000] found SMP MP-table at [c00ff780] 000ff780 Zone PFN ranges: DMA 0x00000010 -> 0x00001000 Normal 0x00001000 -> 0x0001ffc0 HighMem 0x0001ffc0 -> 0x0001ffc0 Movable zone start PFN for each node early_node_map[2] active PFN ranges 0: 0x00000010 -> 0x0000009f 0: 0x00000100 -> 0x0001ffc0 On node 0 totalpages: 130895 free_area_init_node: node 0, pgdat c04f1300, node_mem_map c1000200 DMA zone: 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 3951 pages, LIFO batch:0 Normal zone: 992 pages used for memmap Normal zone: 125920 pages, LIFO batch:31 Using APIC driver default ACPI: PM-Timer IO Port: 0x808 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled) ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ9 used by override. Enabling APIC mode: Flat. Using 1 I/O APICs Using ACPI (MADT) for SMP configuration information SMP: Allowing 4 CPUs, 2 hotplug CPUs nr_irqs_gsi: 24 PM: Registered nosave memory: 000000000009f000 - 00000000000a0000 PM: Registered nosave memory: 00000000000a0000 - 00000000000e6000 PM: Registered nosave memory: 00000000000e6000 - 0000000000100000 Allocating PCI resources starting at 30000000 (gap: 20000000:dee00000) NR_CPUS:32 nr_cpumask_bits:32 nr_cpu_ids:4 nr_node_ids:1 PERCPU: Allocating 40960 bytes of per cpu data Built 1 zonelists in Zone order, mobility grouping on. Total pages: 129871 Kernel command line: BOOT_IMAGE=2.6.29.2 root=UUID=93e4c48e-2222-47da-a3c5-1f7cf113b05e resume=UUID=227b6318-7827-43c1-93ed-0412eefe016e splash=silent vga=788 loglevel=8 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 PID hash table entries: 2048 (order: 11, 8192 bytes) Fast TSC calibration using PIT Detected 3215.126 MHz processor. Console: colour dummy device 80x25 console [tty0] enabled Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 509708k/524032k available (2683k kernel code, 13680k reserved, 1583k data, 452k init, 0k highmem) virtual kernel memory layout: fixmap : 0xffe17000 - 0xfffff000 (1952 kB) pkmap : 0xff800000 - 0xffc00000 (4096 kB) vmalloc : 0xe07c0000 - 0xff7fe000 ( 496 MB) lowmem : 0xc0000000 - 0xdffc0000 ( 511 MB) .init : 0xc0532000 - 0xc05a3000 ( 452 kB) .data : 0xc039ef15 - 0xc052af08 (1583 kB) .text : 0xc0100000 - 0xc039ef15 (2683 kB) Checking if this processor honours the WP bit even in supervisor mode...Ok. SLUB: Genslabs=12, HWalign=128, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 Calibrating delay loop (skipped), value calculated using timer frequency.. 6430.25 BogoMIPS (lpj=3215126) Security Framework initialized Mount-cache hash table entries: 512 CPU: Trace cache: 12K uops, L1 D cache: 16K CPU: L2 cache: 1024K CPU: Physical Processor ID: 0 CPU: Processor Core ID: 0 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU0: Intel P4/Xeon Extended MCE MSRs (24) available CPU0: Thermal monitoring enabled using mwait in idle threads. Checking 'hlt' instruction... OK. ACPI: Core revision 20081204 ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 CPU0: Intel(R) Pentium(R) D CPU 3.20GHz stepping 04 Booting processor 1 APIC 0x1 ip 0x6000 Initializing CPU#1 Calibrating delay using timer specific routine.. 6429.84 BogoMIPS (lpj=3214924) CPU: Trace cache: 12K uops, L1 D cache: 16K CPU: L2 cache: 1024K CPU: Physical Processor ID: 0 CPU: Processor Core ID: 1 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#1. CPU1: Intel P4/Xeon Extended MCE MSRs (24) available CPU1: Thermal monitoring enabled x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106 CPU1: Intel(R) Pentium(R) D CPU 3.20GHz stepping 04 checking TSC synchronization [CPU#0 -> CPU#1]: Measured 900040344 cycles TSC warp between CPUs, turning off TSC clock. Marking TSC unstable due to check_tsc_sync_source failed Brought up 2 CPUs Total of 2 processors activated (12860.10 BogoMIPS). CPU0 attaching sched-domain: domain 0: span 0-1 level CPU groups: 0 1 CPU1 attaching sched-domain: domain 0: span 0-1 level CPU groups: 1 0 net_namespace: 1056 bytes Booting paravirtualized kernel on bare hardware Time: 21:05:19 Date: 06/02/09 NET: Registered protocol family 16 ACPI: bus type pci registered PCI: MCFG configuration 0: base f0000000 segment 0 buses 0 - 255 PCI: Not using MMCONFIG. PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=5 PCI: Using configuration type 1 for base access bio: create slab <bio-0> at 0 ACPI: EC: Look up EC in DSDT ACPI: Interpreter enabled ACPI: (supports S0 S1 S3 S4 S5) ACPI: Using IOAPIC for interrupt routing PCI: MCFG configuration 0: base f0000000 segment 0 buses 0 - 255 PCI: MCFG area at f0000000 reserved in ACPI motherboard resources PCI: updated MCFG configuration 0: base f0000000 segment 0 buses 0 - 63 PCI: Using MMCONFIG for extended config space ACPI: No dock devices found. ACPI: PCI Root Bridge [PCI0] (0000:00) pci 0000:00:01.0: PME# supported from D0 D3hot D3cold pci 0000:00:01.0: PME# disabled pci 0000:00:1b.0: reg 10 64bit mmio: [0xfebf8000-0xfebfbfff] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold pci 0000:00:1b.0: PME# disabled pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold pci 0000:00:1c.0: PME# disabled pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold pci 0000:00:1c.4: PME# disabled pci 0000:00:1c.5: PME# supported from D0 D3hot D3cold pci 0000:00:1c.5: PME# disabled pci 0000:00:1d.0: reg 20 io port: [0xe080-0xe09f] pci 0000:00:1d.1: reg 20 io port: [0xe000-0xe01f] pci 0000:00:1d.2: reg 20 io port: [0xdc00-0xdc1f] pci 0000:00:1d.3: reg 20 io port: [0xd880-0xd89f] pci 0000:00:1d.7: reg 10 32bit mmio: [0xfebff800-0xfebffbff] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold pci 0000:00:1d.7: PME# disabled pci 0000:00:1f.0: Force enabled HPET at 0xfed00000 pci 0000:00:1f.0: quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO pci 0000:00:1f.0: quirk: region 0480-04bf claimed by ICH6 GPIO pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0a00 (mask 00ff) pci 0000:00:1f.0: ICH7 LPC Generic IO decode 2 PIO at 0290 (mask 00ff) pci 0000:00:1f.1: reg 10 io port: [0x00-0x07] pci 0000:00:1f.1: reg 14 io port: [0x00-0x03] pci 0000:00:1f.1: reg 18 io port: [0x00-0x07] pci 0000:00:1f.1: reg 1c io port: [0x00-0x03] pci 0000:00:1f.1: reg 20 io port: [0xffa0-0xffaf] pci 0000:00:1f.2: reg 10 io port: [0xec00-0xec07] pci 0000:00:1f.2: reg 14 io port: [0xe880-0xe883] pci 0000:00:1f.2: reg 18 io port: [0xe800-0xe807] pci 0000:00:1f.2: reg 1c io port: [0xe480-0xe483] pci 0000:00:1f.2: reg 20 io port: [0xe400-0xe41f] pci 0000:00:1f.2: reg 24 32bit mmio: [0xfebffc00-0xfebfffff] pci 0000:00:1f.2: PME# supported from D3hot pci 0000:00:1f.2: PME# disabled pci 0000:00:1f.3: reg 20 io port: [0x400-0x41f] pci 0000:01:00.0: reg 10 32bit mmio: [0xfc000000-0xfcffffff] pci 0000:01:00.0: reg 14 64bit mmio: [0xc0000000-0xdfffffff] pci 0000:01:00.0: reg 1c 64bit mmio: [0xfa000000-0xfbffffff] pci 0000:01:00.0: reg 24 io port: [0x9c00-0x9c7f] pci 0000:01:00.0: reg 30 32bit mmio: [0xfde80000-0xfdefffff] pci 0000:00:01.0: bridge io port: [0x9000-0x9fff] pci 0000:00:01.0: bridge 32bit mmio: [0xf7e00000-0xfdefffff] pci 0000:00:01.0: bridge 64bit mmio pref: [0xaff00000-0xefefffff] pci 0000:03:00.0: reg 10 32bit mmio: [0xfe7e0000-0xfe7fffff] pci 0000:03:00.0: reg 14 32bit mmio: [0xfe000000-0xfe3fffff] pci 0000:03:00.0: reg 18 io port: [0xac00-0xac1f] pci 0000:03:00.0: PME# supported from D0 D3hot D3cold pci 0000:03:00.0: PME# disabled pci 0000:03:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force' pci 0000:00:1c.4: bridge io port: [0xa000-0xafff] pci 0000:00:1c.4: bridge 32bit mmio: [0xfdf00000-0xfe7fffff] pci 0000:04:00.0: reg 10 64bit mmio: [0xfe9ffc00-0xfe9ffc7f] pci 0000:04:00.0: reg 18 64bit mmio: [0xfe9f8000-0xfe9fbfff] pci 0000:04:00.0: reg 20 io port: [0xbc00-0xbc7f] pci 0000:04:00.0: reg 30 32bit mmio: [0xfe900000-0xfe97ffff] pci 0000:04:00.0: supports D1 D2 pci 0000:04:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force' pci 0000:00:1c.5: bridge io port: [0xb000-0xbfff] pci 0000:00:1c.5: bridge 32bit mmio: [0xfe800000-0xfe9fffff] pci 0000:05:04.0: reg 10 32bit mmio: [0xfeaff800-0xfeafffff] pci 0000:05:04.0: reg 14 io port: [0xcc00-0xcc7f] pci 0000:05:04.0: supports D2 pci 0000:05:04.0: PME# supported from D2 D3hot D3cold pci 0000:05:04.0: PME# disabled pci 0000:05:05.0: reg 10 io port: [0xc800-0xc8ff] pci 0000:05:05.0: reg 14 32bit mmio: [0xfeaff400-0xfeaff4ff] pci 0000:05:05.0: reg 30 32bit mmio: [0xfeac0000-0xfeadffff] pci 0000:05:05.0: supports D1 D2 pci 0000:05:05.0: PME# supported from D1 D2 D3hot D3cold pci 0000:05:05.0: PME# disabled pci 0000:00:1e.0: transparent bridge pci 0000:00:1e.0: bridge io port: [0xc000-0xcfff] pci 0000:00:1e.0: bridge 32bit mmio: [0xfea00000-0xfeafffff] pci_bus 0000:00: on NUMA node 0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P8._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P9._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 7 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 *5 6 7 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 *5 6 7 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 11 12 14 *15) ACPI Warning (tbutils-0242): Incorrect checksum in table [OEMB] - F6, should be F1 [20081204] PCI: Using ACPI for IRQ routing NetLabel: Initializing NetLabel: domain hash size = 128 NetLabel: protocols = UNLABELED CIPSOv4 NetLabel: unlabeled traffic allowed by default hpet clockevent registered HPET: 3 timers in total, 0 timers will be used for per-cpu timer hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0 hpet0: 3 comparators, 64-bit 14.318180 MHz counter Switched to high resolution mode on CPU 0 Switched to high resolution mode on CPU 1 pnp: PnP ACPI init ACPI: bus type pnp registered pnp: PnP ACPI: found 16 devices ACPI: ACPI bus type pnp unregistered PnPBIOS: Disabled by ACPI PNP system 00:01: iomem range 0xfed13000-0xfed19fff has been reserved system 00:07: ioport range 0x200-0x207 has been reserved system 00:07: ioport range 0x4d0-0x4d1 has been reserved system 00:07: ioport range 0x800-0x87f has been reserved system 00:07: ioport range 0x480-0x4bf has been reserved system 00:07: iomem range 0xfed1c000-0xfed1ffff has been reserved system 00:07: iomem range 0xfed20000-0xfed8ffff has been reserved system 00:09: iomem range 0xffc00000-0xfff7ffff has been reserved system 00:0a: iomem range 0xfec00000-0xfec00fff has been reserved system 00:0a: iomem range 0xfee00000-0xfee00fff has been reserved system 00:0c: ioport range 0xa00-0xa0f has been reserved system 00:0c: ioport range 0x290-0x29f has been reserved system 00:0e: iomem range 0xf0000000-0xf3ffffff has been reserved system 00:0f: iomem range 0x0-0x9ffff could not be reserved system 00:0f: iomem range 0xc0000-0xcffff could not be reserved system 00:0f: iomem range 0xe0000-0xfffff could not be reserved system 00:0f: iomem range 0x100000-0x1fffffff could not be reserved pci 0000:00:01.0: PCI bridge, secondary bus 0000:01 pci 0000:00:01.0: IO window: 0x9000-0x9fff pci 0000:00:01.0: MEM window: 0xf7e00000-0xfdefffff pci 0000:00:01.0: PREFETCH window: 0x000000aff00000-0x000000efefffff pci 0000:00:1c.0: PCI bridge, secondary bus 0000:02 pci 0000:00:1c.0: IO window: disabled pci 0000:00:1c.0: MEM window: disabled pci 0000:00:1c.0: PREFETCH window: disabled pci 0000:00:1c.4: PCI bridge, secondary bus 0000:03 pci 0000:00:1c.4: IO window: 0xa000-0xafff pci 0000:00:1c.4: MEM window: 0xfdf00000-0xfe7fffff pci 0000:00:1c.4: PREFETCH window: disabled pci 0000:00:1c.5: PCI bridge, secondary bus 0000:04 pci 0000:00:1c.5: IO window: 0xb000-0xbfff pci 0000:00:1c.5: MEM window: 0xfe800000-0xfe9fffff pci 0000:00:1c.5: PREFETCH window: disabled pci 0000:00:1e.0: PCI bridge, secondary bus 0000:05 pci 0000:00:1e.0: IO window: 0xc000-0xcfff pci 0000:00:1e.0: MEM window: 0xfea00000-0xfeafffff pci 0000:00:1e.0: PREFETCH window: 0x00000030000000-0x000000300fffff pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 pci 0000:00:01.0: setting latency timer to 64 pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 pci 0000:00:1c.0: setting latency timer to 64 pci 0000:00:1c.4: PCI INT A -> GSI 16 (level, low) -> IRQ 16 pci 0000:00:1c.4: setting latency timer to 64 pci 0000:00:1c.5: PCI INT B -> GSI 17 (level, low) -> IRQ 17 pci 0000:00:1c.5: setting latency timer to 64 pci 0000:00:1e.0: setting latency timer to 64 pci_bus 0000:00: resource 0 io: [0x00-0xffff] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff] pci_bus 0000:01: resource 0 io: [0x9000-0x9fff] pci_bus 0000:01: resource 1 mem: [0xf7e00000-0xfdefffff] pci_bus 0000:01: resource 2 mem: [0xaff00000-0xefefffff] pci_bus 0000:01: resource 3 mem: [0x0-0x0] pci_bus 0000:02: resource 0 mem: [0x0-0x0] pci_bus 0000:02: resource 1 mem: [0x0-0x0] pci_bus 0000:02: resource 2 mem: [0x0-0x0] pci_bus 0000:02: resource 3 mem: [0x0-0x0] pci_bus 0000:03: resource 0 io: [0xa000-0xafff] pci_bus 0000:03: resource 1 mem: [0xfdf00000-0xfe7fffff] pci_bus 0000:03: resource 2 mem: [0x0-0x0] pci_bus 0000:03: resource 3 mem: [0x0-0x0] pci_bus 0000:04: resource 0 io: [0xb000-0xbfff] pci_bus 0000:04: resource 1 mem: [0xfe800000-0xfe9fffff] pci_bus 0000:04: resource 2 mem: [0x0-0x0] pci_bus 0000:04: resource 3 mem: [0x0-0x0] pci_bus 0000:05: resource 0 io: [0xc000-0xcfff] pci_bus 0000:05: resource 1 mem: [0xfea00000-0xfeafffff] pci_bus 0000:05: resource 2 mem: [0x30000000-0x300fffff] pci_bus 0000:05: resource 3 io: [0x00-0xffff] pci_bus 0000:05: resource 4 mem: [0x000000-0xffffffff] NET: Registered protocol family 2 IP route cache hash table entries: 4096 (order: 2, 16384 bytes) TCP established hash table entries: 16384 (order: 5, 131072 bytes) TCP bind hash table entries: 16384 (order: 5, 131072 bytes) TCP: Hash tables configured (established 16384 bind 16384) TCP reno registered NET: Registered protocol family 1 checking if image is initramfs... it is Freeing initrd memory: 3585k freed apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac) apm: disabled - APM is not SMP safe. audit: initializing netlink socket (disabled) type=2000 audit(1243976719.494:1): initialized HugeTLB registered 4 MB page size, pre-allocated 0 pages VFS: Disk quotas dquot_6.5.2 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) msgmni has been set to 1002 alg: No test for stdrng (krng) Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) pci 0000:01:00.0: Boot video device pcieport-driver 0000:00:01.0: setting latency timer to 64 pcieport-driver 0000:00:01.0: irq 24 for MSI/MSI-X pcieport-driver 0000:00:1c.0: setting latency timer to 64 pcieport-driver 0000:00:1c.0: irq 25 for MSI/MSI-X pcieport-driver 0000:00:1c.4: setting latency timer to 64 pcieport-driver 0000:00:1c.4: irq 26 for MSI/MSI-X pcieport-driver 0000:00:1c.5: setting latency timer to 64 pcieport-driver 0000:00:1c.5: irq 27 for MSI/MSI-X vesafb: framebuffer at 0xfb000000, mapped to 0xe0800000, using 1875k, total 14336k vesafb: mode is 800x600x16, linelength=1600, pages=2 vesafb: protected mode interface info at c000:c380 vesafb: pmi: set display start = c00cc3e3, set palette = c00cc43e vesafb: pmi: ports = 3b4 3b5 3ba 3c0 3c1 3c4 3c5 3c6 3c7 3c8 3c9 3cc 3ce 3cf 3d0 3d1 3d2 3d3 3d4 3d5 3da vesafb: scrolling: redraw vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0 Console: switching to colour frame buffer device 100x37 fb0: VESA VGA frame buffer device isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 00:0d: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A brd: module loaded console [netcon0] enabled netconsole: network logging started PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1 PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp serio: i8042 KBD port at 0x60,0x64 irq 1 mice: PS/2 mouse device common for all mice cpuidle: using governor ladder cpuidle: using governor menu TCP cubic registered Using IPI No-Shortcut mode input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0 PM: Resume from partition UUID=227b6318-7827-43c1-93ed-0412eefe016e PM: Checking hibernation image. PM: Error -6 checking image file PM: Resume from disk failed. registered taskstats version 1 Magic number: 13:888:94 BIOS EDD facility v0.16 2004-Jun-25, 1 devices found Freeing unused kernel memory: 452k freed Clocksource tsc unstable (delta = 279991052 ns) SCSI subsystem initialized Driver 'sd' needs updating - please use bus_type methods libata version 3.00 loaded. ahci 0000:00:1f.2: version 3.0 ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19 ahci 0000:00:1f.2: irq 28 for MSI/MSI-X ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode ahci 0000:00:1f.2: flags: 64bit ncq pm led clo pio slum part ahci 0000:00:1f.2: setting latency timer to 64 scsi0 : ahci scsi1 : ahci scsi2 : ahci scsi3 : ahci ata1: SATA max UDMA/133 abar m1024@0xfebffc00 port 0xfebffd00 irq 28 ata2: SATA max UDMA/133 abar m1024@0xfebffc00 port 0xfebffd80 irq 28 ata3: SATA max UDMA/133 abar m1024@0xfebffc00 port 0xfebffe00 irq 28 ata4: SATA max UDMA/133 abar m1024@0xfebffc00 port 0xfebffe80 irq 28 ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata1.00: ATA-7: HDS728080PLA380, PF2OA69A, max UDMA/133 ata1.00: 160836480 sectors, multi 16: LBA48 NCQ (depth 31/32) ata1.00: configured for UDMA/133 scsi 0:0:0:0: Direct-Access ATA HDS728080PLA380 PF2O PQ: 0 ANSI: 5 sd 0:0:0:0: [sda] 160836480 512-byte hardware sectors: (82.3 GB/76.6 GiB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 0:0:0:0: [sda] 160836480 512-byte hardware sectors: (82.3 GB/76.6 GiB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 < sda5 sda6 > sd 0:0:0:0: [sda] Attached SCSI disk ata2: SATA link down (SStatus 0 SControl 300) ata3: SATA link down (SStatus 0 SControl 300) ata4: SATA link down (SStatus 0 SControl 300) ata_piix 0000:00:1f.1: version 2.12 ata_piix 0000:00:1f.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18 ata_piix 0000:00:1f.1: setting latency timer to 64 scsi4 : ata_piix scsi5 : ata_piix ata5: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14 ata6: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15 ata5.00: ATAPI: HL-DT-ST DVDRAM GSA-4160B, A302, max UDMA/66 ata5.00: configured for UDMA/66 scsi 4:0:0:0: CD-ROM HL-DT-ST DVDRAM GSA-4160B A302 PQ: 0 ANSI: 5 ata6: port disabled. ignoring. sata_sil24 0000:04:00.0: version 1.1 sata_sil24 0000:04:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 sata_sil24 0000:04:00.0: setting latency timer to 64 scsi6 : sata_sil24 scsi7 : sata_sil24 ata7: SATA max UDMA/100 host m128@0xfe9ffc00 port 0xfe9f8000 irq 17 ata8: SATA max UDMA/100 host m128@0xfe9ffc00 port 0xfe9fa000 irq 17 ata7: SATA link down (SStatus 0 SControl 0) ata8: SATA link down (SStatus 0 SControl 0) ohci1394 0000:05:04.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[22] MMIO=[feaff800-feafffff] Max Packet=[2048] IR/IT contexts=[4/8] ieee1394: Host added: ID:BUS[0-00:1023] GUID[0011060000990064] ^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: Stable regression 2.6.29.3 vs 2.6.29.2 2009-06-02 19:09 ` Pascal Terjan @ 2009-06-02 20:44 ` Yinghai Lu 2009-06-02 22:51 ` Pascal Terjan 0 siblings, 1 reply; 14+ messages in thread From: Yinghai Lu @ 2009-06-02 20:44 UTC (permalink / raw) To: Pascal Terjan, Ingo Molnar, Jesse Barnes, Thomas Gleixner, H. Peter Anvin, Andrew Morton, Rafael J. Wysocki Cc: linux-kernel, stable, linux-pci Pascal Terjan wrote: > Le mardi 02 juin 2009 à 10:24 -0700, Yinghai Lu a écrit : > ACPI: Using IOAPIC for interrupt routing > PCI: MCFG configuration 0: base f0000000 segment 0 buses 0 - 255 > PCI: MCFG area at f0000000 reserved in ACPI motherboard resources > PCI: updated MCFG configuration 0: base f0000000 segment 0 buses 0 - 63 > PCI: Using MMCONFIG for extended config space please check [PATCH] x86/pci: fix mmconfig detection with 32bit need 4g Pascal reported and bisected to commit: | x86/PCI: don't call e820_all_mapped with -1 in the mmconfig case for 32bit, mcfg_res->end could be 32bit only ( if 64 res is not used) use end - 1 to pass the value in mcfg->end to avoid overflow don't need to worry about e820 path. they are 64 bit always Reported-by: Pascal Terjan <pterjan@mandriva.com> Bisected-by: Pascal Terjan <pterjan@mandriva.com> Signed-off-by: Yinghai Lu <yinghai@kernel.org> Cc: stable@kernel.org --- arch/x86/pci/mmconfig-shared.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) Index: linux-2.6/arch/x86/pci/mmconfig-shared.c =================================================================== --- linux-2.6.orig/arch/x86/pci/mmconfig-shared.c +++ linux-2.6/arch/x86/pci/mmconfig-shared.c @@ -375,7 +375,7 @@ static acpi_status __init check_mcfg_res if (!fixmem32) return AE_OK; if ((mcfg_res->start >= fixmem32->address) && - (mcfg_res->end <= (fixmem32->address + + (mcfg_res->end < (fixmem32->address + fixmem32->address_length))) { mcfg_res->flags = 1; return AE_CTRL_TERMINATE; @@ -392,7 +392,7 @@ static acpi_status __init check_mcfg_res return AE_OK; if ((mcfg_res->start >= address.minimum) && - (mcfg_res->end <= (address.minimum + address.address_length))) { + (mcfg_res->end < (address.minimum + address.address_length))) { mcfg_res->flags = 1; return AE_CTRL_TERMINATE; } @@ -418,7 +418,7 @@ static int __init is_acpi_reserved(u64 s struct resource mcfg_res; mcfg_res.start = start; - mcfg_res.end = end; + mcfg_res.end = end - 1; mcfg_res.flags = 0; acpi_get_devices("PNP0C01", find_mboard_resource, &mcfg_res, NULL); ^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: Stable regression 2.6.29.3 vs 2.6.29.2 2009-06-02 20:44 ` Yinghai Lu @ 2009-06-02 22:51 ` Pascal Terjan 2009-06-02 22:54 ` Yinghai Lu 2009-06-03 7:13 ` [PATCH] x86/pci: fix mmconfig detection with 32bit near 4g Yinghai Lu 0 siblings, 2 replies; 14+ messages in thread From: Pascal Terjan @ 2009-06-02 22:51 UTC (permalink / raw) To: Yinghai Lu Cc: Ingo Molnar, Jesse Barnes, Thomas Gleixner, H. Peter Anvin, Andrew Morton, Rafael J. Wysocki, linux-kernel, stable, linux-pci Le mardi 02 juin 2009 à 13:44 -0700, Yinghai Lu a écrit : > Pascal Terjan wrote: > > Le mardi 02 juin 2009 à 10:24 -0700, Yinghai Lu a écrit : > > ACPI: Using IOAPIC for interrupt routing > > PCI: MCFG configuration 0: base f0000000 segment 0 buses 0 - 255 > > PCI: MCFG area at f0000000 reserved in ACPI motherboard resources > > PCI: updated MCFG configuration 0: base f0000000 segment 0 buses 0 - 63 > > PCI: Using MMCONFIG for extended config space > > please check > > [PATCH] x86/pci: fix mmconfig detection with 32bit need 4g > I confirm that the machine boots fine with 2.6.29.4 + this patch ^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: Stable regression 2.6.29.3 vs 2.6.29.2 2009-06-02 22:51 ` Pascal Terjan @ 2009-06-02 22:54 ` Yinghai Lu 2009-06-03 9:27 ` Pascal Terjan 2009-06-03 7:13 ` [PATCH] x86/pci: fix mmconfig detection with 32bit near 4g Yinghai Lu 1 sibling, 1 reply; 14+ messages in thread From: Yinghai Lu @ 2009-06-02 22:54 UTC (permalink / raw) To: Pascal Terjan Cc: Ingo Molnar, Jesse Barnes, Thomas Gleixner, H. Peter Anvin, Andrew Morton, Rafael J. Wysocki, linux-kernel, stable, linux-pci Pascal Terjan wrote: > Le mardi 02 juin 2009 à 13:44 -0700, Yinghai Lu a écrit : >> Pascal Terjan wrote: >>> Le mardi 02 juin 2009 à 10:24 -0700, Yinghai Lu a écrit : >>> ACPI: Using IOAPIC for interrupt routing >>> PCI: MCFG configuration 0: base f0000000 segment 0 buses 0 - 255 >>> PCI: MCFG area at f0000000 reserved in ACPI motherboard resources >>> PCI: updated MCFG configuration 0: base f0000000 segment 0 buses 0 - 63 >>> PCI: Using MMCONFIG for extended config space >> please check >> >> [PATCH] x86/pci: fix mmconfig detection with 32bit need 4g >> > > I confirm that the machine boots fine with 2.6.29.4 + this patch Thanks. Pascal Can you try that on tip/master too? http://people.redhat.com/mingo/tip.git/readme.txt YH ^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: Stable regression 2.6.29.3 vs 2.6.29.2 2009-06-02 22:54 ` Yinghai Lu @ 2009-06-03 9:27 ` Pascal Terjan 0 siblings, 0 replies; 14+ messages in thread From: Pascal Terjan @ 2009-06-03 9:27 UTC (permalink / raw) To: Yinghai Lu Cc: Ingo Molnar, Jesse Barnes, Thomas Gleixner, H. Peter Anvin, Andrew Morton, Rafael J. Wysocki, linux-kernel, stable, linux-pci Le mardi 02 juin 2009 à 15:54 -0700, Yinghai Lu a écrit : > Pascal Terjan wrote: > > Le mardi 02 juin 2009 à 13:44 -0700, Yinghai Lu a écrit : > >> Pascal Terjan wrote: > >>> Le mardi 02 juin 2009 à 10:24 -0700, Yinghai Lu a écrit : > >>> ACPI: Using IOAPIC for interrupt routing > >>> PCI: MCFG configuration 0: base f0000000 segment 0 buses 0 - 255 > >>> PCI: MCFG area at f0000000 reserved in ACPI motherboard resources > >>> PCI: updated MCFG configuration 0: base f0000000 segment 0 buses 0 - 63 > >>> PCI: Using MMCONFIG for extended config space > >> please check > >> > >> [PATCH] x86/pci: fix mmconfig detection with 32bit need 4g > >> > > > > I confirm that the machine boots fine with 2.6.29.4 + this patch > > Thanks. Pascal > > Can you try that on tip/master too? > It had the bug and the patch fixes it there too Thanks ^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH] x86/pci: fix mmconfig detection with 32bit near 4g 2009-06-02 22:51 ` Pascal Terjan 2009-06-02 22:54 ` Yinghai Lu @ 2009-06-03 7:13 ` Yinghai Lu 1 sibling, 0 replies; 14+ messages in thread From: Yinghai Lu @ 2009-06-03 7:13 UTC (permalink / raw) To: Ingo Molnar, Jesse Barnes, Thomas Gleixner, H. Peter Anvin, Andrew Morton, Rafael J. Wysocki Cc: linux-kernel, stable, linux-pci, Pascal Terjan Pascal reported and bisected to commit: | x86/PCI: don't call e820_all_mapped with -1 in the mmconfig case broke one system system. ACPI: Using IOAPIC for interrupt routing PCI: MCFG configuration 0: base f0000000 segment 0 buses 0 - 255 PCI: MCFG area at f0000000 reserved in ACPI motherboard resources PCI: Using MMCONFIG for extended config space it didn't have PCI: updated MCFG configuration 0: base f0000000 segment 0 buses 0 - 63 anymore, and try to use 0xf000000 - 0xffffffff for mmconfig for 32bit, mcfg_res->end could be 32bit only (if 64 res is not used) use end - 1 to pass the value in mcfg->end to avoid overflow don't need to worry about e820 path. they are 64 bit always - for 2.6.30 Reported-by: Pascal Terjan <pterjan@mandriva.com> Bisected-by: Pascal Terjan <pterjan@mandriva.com> Tested-by: Pascal Terjan <pterjan@mandriva.com> Signed-off-by: Yinghai Lu <yinghai@kernel.org> Cc: stable@kernel.org --- arch/x86/pci/mmconfig-shared.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) Index: linux-2.6/arch/x86/pci/mmconfig-shared.c =================================================================== --- linux-2.6.orig/arch/x86/pci/mmconfig-shared.c +++ linux-2.6/arch/x86/pci/mmconfig-shared.c @@ -375,7 +375,7 @@ static acpi_status __init check_mcfg_res if (!fixmem32) return AE_OK; if ((mcfg_res->start >= fixmem32->address) && - (mcfg_res->end <= (fixmem32->address + + (mcfg_res->end < (fixmem32->address + fixmem32->address_length))) { mcfg_res->flags = 1; return AE_CTRL_TERMINATE; @@ -392,7 +392,7 @@ static acpi_status __init check_mcfg_res return AE_OK; if ((mcfg_res->start >= address.minimum) && - (mcfg_res->end <= (address.minimum + address.address_length))) { + (mcfg_res->end < (address.minimum + address.address_length))) { mcfg_res->flags = 1; return AE_CTRL_TERMINATE; } @@ -418,7 +418,7 @@ static int __init is_acpi_reserved(u64 s struct resource mcfg_res; mcfg_res.start = start; - mcfg_res.end = end; + mcfg_res.end = end - 1; mcfg_res.flags = 0; acpi_get_devices("PNP0C01", find_mboard_resource, &mcfg_res, NULL); ^ permalink raw reply [flat|nested] 14+ messages in thread
end of thread, other threads:[~2009-06-03 9:28 UTC | newest] Thread overview: 14+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2009-05-29 19:35 Stable regression 2.6.29.3 vs 2.6.29.2 Pascal Terjan 2009-05-29 19:47 ` Rafael J. Wysocki 2009-05-29 19:54 ` Pascal Terjan 2009-05-29 21:32 ` Rafael J. Wysocki 2009-06-02 13:26 ` Pascal Terjan 2009-05-29 19:48 ` Yinghai Lu 2009-06-02 13:28 ` Pascal Terjan 2009-06-02 17:24 ` Yinghai Lu 2009-06-02 19:09 ` Pascal Terjan 2009-06-02 20:44 ` Yinghai Lu 2009-06-02 22:51 ` Pascal Terjan 2009-06-02 22:54 ` Yinghai Lu 2009-06-03 9:27 ` Pascal Terjan 2009-06-03 7:13 ` [PATCH] x86/pci: fix mmconfig detection with 32bit near 4g Yinghai Lu
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).