* sata_nv times out for BD-ROM iHOS104-08
@ 2009-12-22 16:07 Cengiz Gunay
2009-12-23 7:38 ` Tejun Heo
0 siblings, 1 reply; 28+ messages in thread
From: Cengiz Gunay @ 2009-12-22 16:07 UTC (permalink / raw)
To: linux-kernel, linux-ide
[-- Attachment #1: Type: TEXT/PLAIN, Size: 10596 bytes --]
Hello,
I recently got the iHOS-104-08 Blu-ray reader from LiteOn after hearing
customer reviews and a company statement that it works in Linux, but it
just doesn't work on my hardware combination. I saw previous posts here
and elsewhere on sata_nv specific problems, so I hope you can help me, or
at least I can report this properly for future fixes.
I have an ASUS P5NSLI motherboard with a Core2Duo E6400 CPU and a Nvidia
MCP51 SATA controller (rev a1). On this, I have two other SATA disks (in
Nvidia RAID0 configuration) that I boot from both in Linux and Windows and
I have been using this computer for several years without problems. The
LiteOn BD-ROM is attached to the 3rd SATA port (RAID disabled in BIOS) and
I was able to read DVDs on Windows XP. In Linux, with the latest stable
kernel 2.6.32 (note I'm running a 32-bit linux on 64-bit machine for
historical reasons), this is what I get at boot time:
# dmesg | grep ata3
ata3: SATA max UDMA/133 cmd 0x9e0 ctl 0xbe0 bmdma 0xe800 irq 20
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.00: ATAPI: ATAPI iHOS104, WL08, max UDMA/100
ata3.00: configured for UDMA/100
ata3.00: qc timeout (cmd 0xa0)
ata3.00: TEST_UNIT_READY failed (err_mask=0x5)
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.00: configured for UDMA/100
ata3.00: qc timeout (cmd 0xa0)
ata3.00: TEST_UNIT_READY failed (err_mask=0x5)
ata3: limiting SATA link speed to 1.5 Gbps
ata3.00: limiting speed to UDMA/100:PIO3
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.00: configured for UDMA/100
ata3.00: qc timeout (cmd 0xa0)
ata3.00: TEST_UNIT_READY failed (err_mask=0x5)
ata3.00: disabled
ata3: hard resetting link
ata3: nv: skipping hardreset on occupied port
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3: EH complete
In the end the device does not appear in my SCSI device list (see output
of lsscsi below) and I cannot access it. Curiously, I get 0 interrupts
from this SATA controller (see /proc/interrupts at bottom of email).
I tried playing with both sata_nv options, such as ADMA, MSI and SWNCQ. I
learned from posts here that MCP51 doesn't have support for ADMA, but
either way the messages I get did not change. I also failed to force DMA
and speed selection behavior using libata.dma and libata.force on the
kernel command-line. I wasn't able to influence sata_nv's decisions any
bit. "acpi=off noapic" and "acpi_use_time_override" also did not help. I
have a working HPET timer in the BIOS.
I was unable to get another driver like the SATA AHCI or one of the PATA
drivers to take over this device. Is that even possible?
I would appreciate any suggestions and would happily debug this a little
further. And, of course, happy holidays everybody. Details of my
configuration follow.
--
Cengiz Gunay
SYSTEM DETAILS:
---------------------------------
I have a Debian unstable/experimental system:
# uname -a
Linux salon 2.6.32 #1 SMP PREEMPT Mon Dec 21 10:40:35 EST 2009 i686
GNU/Linux
Dmesg snippet (full listing attached) showing sata_nv initialization and
irq assignment:
--
sata_nv 0000:00:0e.0: version 3.5
ACPI: PCI Interrupt Link [APSI] enabled at IRQ 21
sata_nv 0000:00:0e.0: PCI INT A -> Link[APSI] -> GSI 21 (level, low) ->
IRQ 21
sata_nv 0000:00:0e.0: Using SWNCQ mode
sata_nv 0000:00:0e.0: setting latency timer to 64
scsi1 : sata_nv
PM: Adding info for scsi:host1
PM: Adding info for No Bus:host1
scsi2 : sata_nv
PM: Adding info for scsi:host2
PM: Adding info for No Bus:host2
ata1: SATA max UDMA/133 cmd 0x9f0 ctl 0xbf0 bmdma 0xd400 irq 21
ata2: SATA max UDMA/133 cmd 0x970 ctl 0xb70 bmdma 0xd408 irq 21
ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 20
sata_nv 0000:00:0f.0: PCI INT A -> Link[APSJ] -> GSI 20 (level, low) ->
IRQ 20
sata_nv 0000:00:0f.0: Using SWNCQ mode
sata_nv 0000:00:0f.0: setting latency timer to 64
scsi3 : sata_nv
PM: Adding info for scsi:host3
PM: Adding info for No Bus:host3
scsi4 : sata_nv
PM: Adding info for scsi:host4
PM: Adding info for No Bus:host4
ata3: SATA max UDMA/133 cmd 0x9e0 ctl 0xbe0 bmdma 0xe800 irq 20
ata4: SATA max UDMA/133 cmd 0x960 ctl 0xb60 bmdma 0xe808 irq 20
--
# lsscsi
[0:0:0:0] disk Generic USB SD Reader 1.00 /dev/sdc
[0:0:0:1] disk Generic USB CF Reader 1.01 /dev/sdd
[0:0:0:2] disk Generic USB SM Reader 1.02 /dev/sde
[0:0:0:3] disk Generic USB MS Reader 1.03 /dev/sdf
[1:0:0:0] disk ATA SAMSUNG SP2504C VT10 /dev/sda
[2:0:0:0] disk ATA ST3250620AS 3.AA /dev/sdb
[5:0:0:0] disk USB DISK 2.0 0403 /dev/sdg
I get 0 interrupts from IRQ 20 assigned to 2nd SATA channel (ata3 and
ata4).
# cat /proc/interrupts
CPU0 CPU1
0: 144 0 IO-APIC-edge timer
1: 2 0 IO-APIC-edge i8042
7: 1 0 IO-APIC-edge
9: 0 0 IO-APIC-fasteoi acpi
12: 4 0 IO-APIC-edge i8042
15: 6483 0 IO-APIC-edge ide0
16: 147431 0 IO-APIC-fasteoi ohci1394, nvidia
17: 95671 0 IO-APIC-fasteoi eth1
20: 6 0 IO-APIC-fasteoi sata_nv
21: 53915 0 IO-APIC-fasteoi sata_nv
22: 67354 0 IO-APIC-fasteoi ehci_hcd:usb2
23: 633 0 IO-APIC-fasteoi ohci_hcd:usb1, HDA Intel
NMI: 0 0 Non-maskable interrupts
LOC: 2572087 2602175 Local timer interrupts
SPU: 0 0 Spurious interrupts
PMI: 0 0 Performance monitoring interrupts
PND: 0 0 Performance pending work
RES: 32606 35770 Rescheduling interrupts
CAL: 349 609 Function call interrupts
TLB: 2548 3449 TLB shootdowns
TRM: 0 0 Thermal event interrupts
THR: 0 0 Threshold APIC interrupts
MCE: 0 0 Machine check exceptions
MCP: 8 8 Machine check polls
ERR: 1
MIS: 0
# lspci (full "lspci -vv" attached)
00:00.0 Host bridge: nVidia Corporation Device 0071 (rev a3)
00:00.1 RAM memory: nVidia Corporation Device 007f (rev a1)
00:00.2 RAM memory: nVidia Corporation Device 0075 (rev a1)
00:00.3 RAM memory: nVidia Corporation Device 006f (rev a1)
00:00.4 RAM memory: nVidia Corporation Device 00b4 (rev a1)
00:01.0 RAM memory: nVidia Corporation Device 0076 (rev a1)
00:01.1 RAM memory: nVidia Corporation Device 0078 (rev a1)
00:01.2 RAM memory: nVidia Corporation Device 0079 (rev a1)
00:01.3 RAM memory: nVidia Corporation Device 007a (rev a1)
00:01.4 RAM memory: nVidia Corporation Device 007b (rev a1)
00:01.5 RAM memory: nVidia Corporation Device 007c (rev a1)
00:01.6 RAM memory: nVidia Corporation Device 007d (rev a1)
00:02.0 PCI bridge: nVidia Corporation Device 007e (rev a2)
00:04.0 PCI bridge: nVidia Corporation Device 007e (rev a2)
00:05.0 PCI bridge: nVidia Corporation Device 007e (rev a2)
00:06.0 PCI bridge: nVidia Corporation Device 007e (rev a2)
00:07.0 PCI bridge: nVidia Corporation Device 007e (rev a2)
00:09.0 RAM memory: nVidia Corporation MCP51 Host Bridge (rev a2)
00:0a.0 ISA bridge: nVidia Corporation MCP51 LPC Bridge (rev a2)
00:0a.1 SMBus: nVidia Corporation MCP51 SMBus (rev a2)
00:0a.2 RAM memory: nVidia Corporation MCP51 Memory Controller 0 (rev a2)
00:0b.0 USB Controller: nVidia Corporation MCP51 USB Controller (rev a2)
00:0b.1 USB Controller: nVidia Corporation MCP51 USB Controller (rev a2)
00:0d.0 IDE interface: nVidia Corporation MCP51 IDE (rev a1)
00:0e.0 RAID bus controller: nVidia Corporation MCP51 Serial ATA
Controller (rev a1)
00:0f.0 IDE interface: nVidia Corporation MCP51 Serial ATA Controller (rev
a1)
00:10.0 PCI bridge: nVidia Corporation MCP51 PCI Bridge (rev a2)
00:10.1 Audio device: nVidia Corporation MCP51 High Definition Audio (rev
a2)
01:00.0 VGA compatible controller: nVidia Corporation G71 [GeForce 7900
GT/GTO] (rev a1)
06:06.0 FireWire (IEEE 1394): VIA Technologies, Inc. VT6306 Fire II IEEE
1394 OHCI Link Layer Controller (rev 46)
06:07.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8169
Gigabit Ethernet (rev 10)
# lspci -vv -s 00:0f.0 (full "lspci -vv" attached)
00:0f.0 IDE interface: nVidia Corporation MCP51 Serial ATA Controller (rev
a1) (prog-if 85 [Master SecO PriO])
Subsystem: ASUSTeK Computer Inc. A8N-VM CSM Mainboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 20
Region 0: I/O ports at 09e0 [size=8]
Region 1: I/O ports at 0be0 [size=4]
Region 2: I/O ports at 0960 [size=8]
Region 3: I/O ports at 0b60 [size=4]
Region 4: I/O ports at e800 [size=16]
Region 5: Memory at d5005000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [b0] MSI: Enable- Count=1/4 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [cc] HyperTransport: MSI Mapping Enable- Fixed+
Kernel driver in use: sata_nv
Kernel modules: sata_nv
# lspci -vv -s 00:0e.0
00:0e.0 RAID bus controller: nVidia Corporation MCP51 Serial ATA
Controller (rev a1) (prog-if 85)
Subsystem: ASUSTeK Computer Inc. A8N-VM CSM Mainboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 21
Region 0: I/O ports at 09f0 [size=8]
Region 1: I/O ports at 0bf0 [size=4]
Region 2: I/O ports at 0970 [size=8]
Region 3: I/O ports at 0b70 [size=4]
Region 4: I/O ports at d400 [size=16]
Region 5: Memory at d5004000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [b0] MSI: Enable- Count=1/4 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [cc] HyperTransport: MSI Mapping Enable- Fixed+
Kernel driver in use: sata_nv
Kernel modules: sata_nv
[-- Attachment #2: Type: TEXT/PLAIN, Size: 79299 bytes --]
Linux version 2.6.32 (root@salon) (gcc version 4.3.3 (Debian 4.3.3-10) ) #1 SMP PREEMPT Mon Dec 21 10:40:35 EST 2009
KERNEL supported cpus:
Intel GenuineIntel
AMD AuthenticAMD
NSC Geode by NSC
Cyrix CyrixInstead
Centaur CentaurHauls
Transmeta GenuineTMx86
Transmeta TransmetaCPU
UMC UMC UMC UMC
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009c400 (usable)
BIOS-e820: 000000000009c400 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000007fef0000 (usable)
BIOS-e820: 000000007fef0000 - 000000007fef3000 (ACPI NVS)
BIOS-e820: 000000007fef3000 - 000000007ff00000 (ACPI data)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
DMI 2.4 present.
Phoenix BIOS detected: BIOS may corrupt low RAM, working around it.
e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
last_pfn = 0x7fef0 max_arch_pfn = 0x100000
MTRR default type: uncachable
MTRR fixed ranges enabled:
00000-9FFFF write-back
A0000-BFFFF uncachable
C0000-CDFFF write-protect
CE000-FFFFF uncachable
MTRR variable ranges enabled:
0 base 000000000 mask F80000000 write-back
1 base 07FF00000 mask FFFF00000 uncachable
2 disabled
3 disabled
4 disabled
5 disabled
6 disabled
7 disabled
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
initial memory mapped : 0 - 01800000
init_memory_mapping: 0000000000000000-00000000377fe000
0000000000 - 0000400000 page 4k
0000400000 - 0037400000 page 2M
0037400000 - 00377fe000 page 4k
kernel direct mapping tables up to 377fe000 @ 10000-15000
RAMDISK: 36bb4000 - 37fef756
Allocated new RAMDISK: 013e6000 - 02821756
Move RAMDISK from 0000000036bb4000 - 0000000037fef755 to 013e6000 - 02821755
ACPI: RSDP 000f7900 00024 (v02 Nvidia)
ACPI: XSDT 7fef30c0 0004C (v01 Nvidia ASUSACPI 42302E31 AWRD 00000000)
ACPI: FACP 7fefa600 000F4 (v03 Nvidia ASUSACPI 42302E31 AWRD 00000000)
ACPI: DSDT 7fef3240 07354 (v01 NVIDIA ASUSACPI 00001000 MSFT 03000000)
ACPI: FACS 7fef0000 00040
ACPI: HPET 7fefa840 00038 (v01 Nvidia ASUSACPI 42302E31 AWRD 00000098)
ACPI: MCFG 7fefa8c0 0003C (v01 Nvidia ASUSACPI 42302E31 AWRD 00000000)
ACPI: APIC 7fefa740 0008E (v01 Nvidia ASUSACPI 42302E31 AWRD 00000000)
ACPI: SSDT 7fefae20 0032C (v01 Nvidia ASUSACPI 42302E31 AWRD 00000000)
ACPI: Local APIC address 0xfee00000
1158MB HIGHMEM available.
887MB LOWMEM available.
mapped low ram: 0 - 377fe000
low ram: 0 - 377fe000
node 0 low ram: 00000000 - 377fe000
node 0 bootmap 00011000 - 00017f00
(9 early reservations) ==> bootmem [0000000000 - 00377fe000]
#0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
#1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000]
#2 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 - 0000007000]
#3 [0001000000 - 00013de7c4] TEXT DATA BSS ==> [0001000000 - 00013de7c4]
#4 [000009c400 - 0000100000] BIOS reserved ==> [000009c400 - 0000100000]
#5 [00013df000 - 00013e5149] BRK ==> [00013df000 - 00013e5149]
#6 [0000010000 - 0000011000] PGTABLE ==> [0000010000 - 0000011000]
#7 [00013e6000 - 0002821756] NEW RAMDISK ==> [00013e6000 - 0002821756]
#8 [0000011000 - 0000018000] BOOTMAP ==> [0000011000 - 0000018000]
found SMP MP-table at [c00f5d50] f5d50
Zone PFN ranges:
DMA 0x00000010 -> 0x00001000
Normal 0x00001000 -> 0x000377fe
HighMem 0x000377fe -> 0x0007fef0
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
0: 0x00000010 -> 0x0000009c
0: 0x00000100 -> 0x0007fef0
On node 0 totalpages: 523900
free_area_init_node: node 0, pgdat c1324fc0, node_mem_map c2823200
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 3948 pages, LIFO batch:0
Normal zone: 1744 pages used for memmap
Normal zone: 221486 pages, LIFO batch:31
HighMem zone: 2318 pages used for memmap
HighMem zone: 294372 pages, LIFO batch:31
Using APIC driver default
ACPI: PM-Timer IO Port: 0x4008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 4, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
ACPI: IRQ9 used by override.
ACPI: IRQ14 used by override.
ACPI: IRQ15 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
ACPI: HPET id: 0x10de8201 base: 0xfeff0000
SMP: Allowing 4 CPUs, 2 hotplug CPUs
nr_irqs_gsi: 24
PM: Registered nosave memory: 000000000009c000 - 000000000009d000
PM: Registered nosave memory: 000000000009d000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
Allocating PCI resources starting at 7ff00000 (gap: 7ff00000:60100000)
NR_CPUS:4 nr_cpumask_bits:4 nr_cpu_ids:4 nr_node_ids:1
PERCPU: Embedded 11 pages/cpu @c3c00000 s23512 r0 d21544 u1048576
pcpu-alloc: s23512 r0 d21544 u1048576 alloc=1*4194304
pcpu-alloc: [0] 0 1 2 3
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 519806
Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.32 root=/dev/mapper/nvidia_ceebaiib1 ro
PID hash table entries: 4096 (order: 2, 16384 bytes)
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
Initializing HighMem for node 0 (000377fe:0007fef0)
Memory: 2052264k/2096064k available (2319k kernel code, 42132k reserved, 912k data, 404k init, 1186760k highmem)
virtual kernel memory layout:
fixmap : 0xfff6b000 - 0xfffff000 ( 592 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xf7ffe000 - 0xff7fe000 ( 120 MB)
lowmem : 0xc0000000 - 0xf77fe000 ( 887 MB)
.init : 0xc1329000 - 0xc138e000 ( 404 kB)
.data : 0xc1243e41 - 0xc1328128 ( 912 kB)
.text : 0xc1000000 - 0xc1243e41 (2319 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:384
Extended CMOS year: 2000
spurious 8259A interrupt: IRQ7.
Console: colour VGA+ 80x25
console [tty0] enabled
hpet clockevent registered
Fast TSC calibration using PIT
Detected 2133.579 MHz processor.
Calibrating delay loop (skipped), value calculated using timer frequency.. 4267.15 BogoMIPS (lpj=2133579)
Security Framework initialized
Mount-cache hash table entries: 512
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
mce: CPU supports 6 MCE banks
CPU0: Thermal monitoring enabled (TM2)
using mwait in idle threads.
Checking 'hlt' instruction... OK.
ACPI: Core revision 20090903
..TIMER: vector=0x30 apic1=0 pin1=0 apic2=-1 pin2=-1
..MP-BIOS bug: 8254 timer not connected to IO-APIC
...trying to set up timer (IRQ0) through the 8259A ...
..... (found apic 0 pin 0) ...
....... works.
CPU0: Intel(R) Core(TM)2 CPU 6400 @ 2.13GHz stepping 06
Booting processor 1 APIC 0x1 ip 0x6000
Initializing CPU#1
Calibrating delay using timer specific routine.. 4266.83 BogoMIPS (lpj=2133419)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU1: Thermal monitoring enabled (TM2)
CPU1: Intel(R) Core(TM)2 CPU 6400 @ 2.13GHz stepping 06
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Brought up 2 CPUs
Total of 2 processors activated (8533.99 BogoMIPS).
CPU0 attaching sched-domain:
domain 0: span 0-1 level MC
groups: 0 1
CPU1 attaching sched-domain:
domain 0: span 0-1 level MC
groups: 1 0
PM: Adding info for No Bus:platform
Time: 9:28:46 Date: 12/22/09
NET: Registered protocol family 16
PM: Adding info for No Bus:vtcon0
EISA bus registered
ACPI: bus type pci registered
PM: Adding info for No Bus:id
PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
PCI: MCFG area at e0000000 reserved in E820
PCI: Using MMCONFIG for extended config space
PCI: Using configuration type 1 for base access
PM: Adding info for No Bus:default
bio: create slab <bio-0> at 0
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
PM: Adding info for acpi:LNXSYSTM:00
PM: Adding info for acpi:LNXCPU:00
PM: Adding info for acpi:LNXCPU:01
PM: Adding info for acpi:LNXCPU:02
PM: Adding info for acpi:LNXCPU:03
PM: Adding info for acpi:LNXSYBUS:00
PM: Adding info for acpi:PNP0C0C:00
PM: Adding info for acpi:PNP0A08:00
PM: Adding info for acpi:PNP0C02:00
PM: Adding info for acpi:device:00
PM: Adding info for acpi:device:01
PM: Adding info for acpi:device:02
PM: Adding info for acpi:device:03
PM: Adding info for acpi:device:04
PM: Adding info for acpi:device:05
PM: Adding info for acpi:device:06
PM: Adding info for acpi:device:07
PM: Adding info for acpi:device:08
PM: Adding info for acpi:device:09
PM: Adding info for acpi:device:0a
PM: Adding info for acpi:device:0b
PM: Adding info for acpi:device:0c
PM: Adding info for acpi:device:0d
PM: Adding info for acpi:device:0e
PM: Adding info for acpi:device:0f
PM: Adding info for acpi:device:10
PM: Adding info for acpi:device:11
PM: Adding info for acpi:device:12
PM: Adding info for acpi:device:13
PM: Adding info for acpi:device:14
PM: Adding info for acpi:device:15
PM: Adding info for acpi:device:16
PM: Adding info for acpi:device:17
PM: Adding info for acpi:device:18
PM: Adding info for acpi:device:19
PM: Adding info for acpi:PNP0C02:01
PM: Adding info for acpi:PNP0000:00
PM: Adding info for acpi:PNP0200:00
PM: Adding info for acpi:PNP0100:00
PM: Adding info for acpi:PNP0103:00
PM: Adding info for acpi:PNP0B00:00
PM: Adding info for acpi:PNP0800:00
PM: Adding info for acpi:PNP0C04:00
PM: Adding info for acpi:device:1a
PM: Adding info for acpi:device:1b
PM: Adding info for acpi:device:1c
PM: Adding info for acpi:device:1d
PM: Adding info for acpi:device:1e
PM: Adding info for acpi:device:1f
PM: Adding info for acpi:NVRAIDBUS:00
PM: Adding info for acpi:ATK0110:00
PM: Adding info for acpi:PNP0C0F:00
PM: Adding info for acpi:PNP0C0F:01
PM: Adding info for acpi:PNP0C0F:02
PM: Adding info for acpi:PNP0C0F:03
PM: Adding info for acpi:PNP0C0F:04
PM: Adding info for acpi:PNP0C0F:05
PM: Adding info for acpi:PNP0C0F:06
PM: Adding info for acpi:PNP0C0F:07
PM: Adding info for acpi:PNP0C0F:08
PM: Adding info for acpi:PNP0C0F:09
PM: Adding info for acpi:PNP0C0F:0a
PM: Adding info for acpi:PNP0C0F:0b
PM: Adding info for acpi:PNP0C0F:0c
PM: Adding info for acpi:PNP0C0F:0d
PM: Adding info for acpi:PNP0C0F:0e
PM: Adding info for acpi:PNP0C0F:0f
PM: Adding info for acpi:PNP0C0F:10
PM: Adding info for acpi:PNP0C0F:11
PM: Adding info for acpi:PNP0C0F:12
PM: Adding info for acpi:PNP0C0F:13
PM: Adding info for acpi:PNP0C0F:14
PM: Adding info for acpi:PNP0C0F:15
PM: Adding info for acpi:PNP0C0F:16
PM: Adding info for acpi:PNP0C0F:17
PM: Adding info for acpi:PNP0C0F:18
PM: Adding info for acpi:PNP0C0F:19
PM: Adding info for acpi:PNP0C0F:1a
PM: Adding info for acpi:PNP0C0F:1b
PM: Adding info for acpi:PNP0C0F:1c
PM: Adding info for acpi:PNP0C0F:1d
PM: Adding info for acpi:PNP0C0F:1e
PM: Adding info for acpi:PNP0C0F:1f
PM: Adding info for acpi:PNP0C0F:20
PM: Adding info for acpi:PNP0C0F:21
PM: Adding info for acpi:PNP0C0F:22
PM: Adding info for acpi:PNP0C0F:23
PM: Adding info for acpi:PNP0C0F:24
PM: Adding info for acpi:PNP0C0F:25
PM: Adding info for acpi:PNP0C0F:26
PM: Adding info for acpi:PNP0C0F:27
PM: Adding info for acpi:PNP0C0F:28
PM: Adding info for acpi:PNP0C02:02
PM: Adding info for acpi:PNP0C01:00
PM: Adding info for acpi:LNXTHERM:00
PM: Adding info for acpi:PNP0C0B:00
PM: Adding info for acpi:LNXTHERM:01
PM: Adding info for acpi:LNXPWRBN:00
ACPI: No dock devices found.
ACPI: PCI Root Bridge [PCI0] (0000:00)
PM: Adding info for No Bus:pci0000:00
PM: Adding info for No Bus:0000:00
pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:02.0: PME# disabled
pci 0000:00:04.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:04.0: PME# disabled
pci 0000:00:05.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:05.0: PME# disabled
pci 0000:00:06.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:06.0: PME# disabled
pci 0000:00:07.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:07.0: PME# disabled
pci 0000:00:0a.1: reg 20 io port: [0x5000-0x503f]
pci 0000:00:0a.1: reg 24 io port: [0x5100-0x513f]
pci 0000:00:0a.1: PME# supported from D3hot D3cold
pci 0000:00:0a.1: PME# disabled
pci 0000:00:0b.0: reg 10 32bit mmio: [0xd5006000-0xd5006fff]
pci 0000:00:0b.0: supports D1 D2
pci 0000:00:0b.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:0b.0: PME# disabled
pci 0000:00:0b.1: reg 10 32bit mmio: [0xd5007000-0xd50070ff]
pci 0000:00:0b.1: supports D1 D2
pci 0000:00:0b.1: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:0b.1: PME# disabled
pci 0000:00:0d.0: reg 20 io port: [0xf000-0xf00f]
pci 0000:00:0e.0: reg 10 io port: [0x9f0-0x9f7]
pci 0000:00:0e.0: reg 14 io port: [0xbf0-0xbf3]
pci 0000:00:0e.0: reg 18 io port: [0x970-0x977]
pci 0000:00:0e.0: reg 1c io port: [0xb70-0xb73]
pci 0000:00:0e.0: reg 20 io port: [0xd400-0xd40f]
pci 0000:00:0e.0: reg 24 32bit mmio: [0xd5004000-0xd5004fff]
pci 0000:00:0f.0: reg 10 io port: [0x9e0-0x9e7]
pci 0000:00:0f.0: reg 14 io port: [0xbe0-0xbe3]
pci 0000:00:0f.0: reg 18 io port: [0x960-0x967]
pci 0000:00:0f.0: reg 1c io port: [0xb60-0xb63]
pci 0000:00:0f.0: reg 20 io port: [0xe800-0xe80f]
pci 0000:00:0f.0: reg 24 32bit mmio: [0xd5005000-0xd5005fff]
pci 0000:00:10.1: reg 10 32bit mmio: [0xd5000000-0xd5003fff]
pci 0000:00:10.1: PME# supported from D3hot D3cold
pci 0000:00:10.1: PME# disabled
pci 0000:01:00.0: reg 10 32bit mmio: [0xd0000000-0xd0ffffff]
pci 0000:01:00.0: reg 14 64bit mmio pref: [0xc0000000-0xcfffffff]
pci 0000:01:00.0: reg 1c 64bit mmio: [0xd1000000-0xd1ffffff]
pci 0000:01:00.0: reg 24 io port: [0xa000-0xa07f]
pci 0000:01:00.0: reg 30 32bit mmio pref: [0xd2000000-0xd201ffff]
pci 0000:00:02.0: bridge io port: [0xa000-0xafff]
pci 0000:00:02.0: bridge 32bit mmio: [0xd0000000-0xd2ffffff]
pci 0000:00:02.0: bridge 64bit mmio pref: [0xc0000000-0xcfffffff]
pci 0000:06:06.0: reg 10 32bit mmio: [0xd4001000-0xd40017ff]
pci 0000:06:06.0: reg 14 io port: [0xb000-0xb07f]
pci 0000:06:06.0: supports D2
pci 0000:06:06.0: PME# supported from D2 D3hot D3cold
pci 0000:06:06.0: PME# disabled
pci 0000:06:07.0: reg 10 io port: [0xb400-0xb4ff]
pci 0000:06:07.0: reg 14 32bit mmio: [0xd4000000-0xd40000ff]
pci 0000:06:07.0: reg 30 32bit mmio pref: [0xd3000000-0xd301ffff]
pci 0000:06:07.0: supports D1 D2
pci 0000:06:07.0: PME# supported from D1 D2 D3hot D3cold
pci 0000:06:07.0: PME# disabled
pci 0000:00:10.0: transparent bridge
pci 0000:00:10.0: bridge io port: [0xb000-0xbfff]
pci 0000:00:10.0: bridge 32bit mmio: [0xd3000000-0xd4ffffff]
pci_bus 0000:00: on NUMA node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
PM: Adding info for pci:0000:00:00.0
PM: Adding info for pci:0000:00:00.1
PM: Adding info for pci:0000:00:00.2
PM: Adding info for pci:0000:00:00.3
PM: Adding info for pci:0000:00:00.4
PM: Adding info for pci:0000:00:01.0
PM: Adding info for pci:0000:00:01.1
PM: Adding info for pci:0000:00:01.2
PM: Adding info for pci:0000:00:01.3
PM: Adding info for pci:0000:00:01.4
PM: Adding info for pci:0000:00:01.5
PM: Adding info for pci:0000:00:01.6
PM: Adding info for pci:0000:00:02.0
PM: Adding info for pci:0000:00:04.0
PM: Adding info for pci:0000:00:05.0
PM: Adding info for pci:0000:00:06.0
PM: Adding info for pci:0000:00:07.0
PM: Adding info for pci:0000:00:09.0
PM: Adding info for pci:0000:00:0a.0
PM: Adding info for pci:0000:00:0a.1
PM: Adding info for pci:0000:00:0a.2
PM: Adding info for pci:0000:00:0b.0
PM: Adding info for pci:0000:00:0b.1
PM: Adding info for pci:0000:00:0d.0
PM: Adding info for pci:0000:00:0e.0
PM: Adding info for pci:0000:00:0f.0
PM: Adding info for pci:0000:00:10.0
PM: Adding info for pci:0000:00:10.1
PM: Adding info for pci:0000:01:00.0
PM: Adding info for No Bus:0000:01
PM: Adding info for No Bus:0000:02
PM: Adding info for No Bus:0000:03
PM: Adding info for No Bus:0000:04
PM: Adding info for No Bus:0000:05
PM: Adding info for pci:0000:06:06.0
PM: Adding info for pci:0000:06:07.0
PM: Adding info for No Bus:0000:06
ACPI: PCI Interrupt Link [LNK1] (IRQs 5 7 9 *10 11 14 15)
ACPI: PCI Interrupt Link [LNK2] (IRQs *5 7 9 10 11 14 15)
ACPI: PCI Interrupt Link [LNK3] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK4] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK5] (IRQs 5 *7 9 10 11 14 15)
ACPI: PCI Interrupt Link [LNK6] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK7] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK8] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LUBA] (IRQs 5 *7 9 10 11 14 15)
ACPI: PCI Interrupt Link [LUBB] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LMAC] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LACI] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LAZA] (IRQs 5 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [LPMU] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LMCI] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSMB] (IRQs 5 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [LUB2] (IRQs *5 7 9 10 11 14 15)
ACPI: PCI Interrupt Link [LIDE] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSID] (IRQs 5 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [LFID] (IRQs 5 7 9 *10 11 14 15)
ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0
ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0
ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0, disabled.
ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled.
ACPI: PCI Interrupt Link [APC5] (IRQs 16) *0
ACPI: PCI Interrupt Link [APC6] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APC7] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APC8] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APMU] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [AAZA] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0
PM: Adding info for No Bus:vga_arbiter
vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
vgaarb: loaded
PCI: Using ACPI for IRQ routing
PM: Adding info for No Bus:lo
hpet0: at MMIO 0xfeff0000, IRQs 2, 8, 31
hpet0: 3 comparators, 32-bit 25.000000 MHz counter
Switching to clocksource tsc
pnp: PnP ACPI init
PM: Adding info for No Bus:pnp0
ACPI: bus type pnp registered
PM: Adding info for pnp:00:00
PM: Adding info for pnp:00:01
PM: Adding info for pnp:00:02
PM: Adding info for pnp:00:03
PM: Adding info for pnp:00:04
PM: Adding info for pnp:00:05
PM: Adding info for pnp:00:06
PM: Adding info for pnp:00:07
PM: Adding info for pnp:00:08
PM: Adding info for pnp:00:09
pnp: PnP ACPI: found 10 devices
ACPI: ACPI bus type pnp unregistered
PnPBIOS: Disabled by ACPI PNP
system 00:01: ioport range 0x4000-0x407f has been reserved
system 00:01: ioport range 0x4080-0x40ff has been reserved
system 00:01: ioport range 0x4400-0x447f has been reserved
system 00:01: ioport range 0x4480-0x44ff has been reserved
system 00:01: ioport range 0x4800-0x487f has been reserved
system 00:01: ioport range 0x4880-0x48ff has been reserved
system 00:02: ioport range 0x4d0-0x4d1 has been reserved
system 00:02: ioport range 0x800-0x87f has been reserved
system 00:02: ioport range 0x290-0x297 has been reserved
system 00:02: ioport range 0x880-0x88f has been reserved
system 00:08: iomem range 0xe0000000-0xefffffff has been reserved
system 00:09: iomem range 0xdbc00-0xdbfff has been reserved
system 00:09: iomem range 0xf0000-0xf7fff could not be reserved
system 00:09: iomem range 0xf8000-0xfbfff could not be reserved
system 00:09: iomem range 0xfc000-0xfffff could not be reserved
system 00:09: iomem range 0xfeff0000-0xfeff00ff has been reserved
system 00:09: iomem range 0x7fef0000-0x7fefffff could not be reserved
system 00:09: iomem range 0xffff0000-0xffffffff has been reserved
system 00:09: iomem range 0x0-0x9ffff could not be reserved
system 00:09: iomem range 0x100000-0x7feeffff could not be reserved
system 00:09: iomem range 0xfec00000-0xfec00fff could not be reserved
system 00:09: iomem range 0xfee00000-0xfee00fff has been reserved
system 00:09: iomem range 0xfeff0000-0xfeff03ff could not be reserved
PM: Adding info for No Bus:mem
PM: Adding info for No Bus:kmem
PM: Adding info for No Bus:null
PM: Adding info for No Bus:port
PM: Adding info for No Bus:zero
PM: Adding info for No Bus:full
PM: Adding info for No Bus:random
PM: Adding info for No Bus:urandom
PM: Adding info for No Bus:kmsg
pci 0000:06:07.0: BAR 6: address space collision on of device [0xd3000000-0xd301ffff]
pci 0000:00:02.0: PCI bridge, secondary bus 0000:01
pci 0000:00:02.0: IO window: 0xa000-0xafff
pci 0000:00:02.0: MEM window: 0xd0000000-0xd2ffffff
pci 0000:00:02.0: PREFETCH window: 0x000000c0000000-0x000000cfffffff
pci 0000:00:04.0: PCI bridge, secondary bus 0000:02
pci 0000:00:04.0: IO window: disabled
pci 0000:00:04.0: MEM window: disabled
pci 0000:00:04.0: PREFETCH window: disabled
pci 0000:00:05.0: PCI bridge, secondary bus 0000:03
pci 0000:00:05.0: IO window: disabled
pci 0000:00:05.0: MEM window: disabled
pci 0000:00:05.0: PREFETCH window: disabled
pci 0000:00:06.0: PCI bridge, secondary bus 0000:04
pci 0000:00:06.0: IO window: disabled
pci 0000:00:06.0: MEM window: disabled
pci 0000:00:06.0: PREFETCH window: disabled
pci 0000:00:07.0: PCI bridge, secondary bus 0000:05
pci 0000:00:07.0: IO window: disabled
pci 0000:00:07.0: MEM window: disabled
pci 0000:00:07.0: PREFETCH window: disabled
pci 0000:00:10.0: PCI bridge, secondary bus 0000:06
pci 0000:00:10.0: IO window: 0xb000-0xbfff
pci 0000:00:10.0: MEM window: 0xd3000000-0xd4ffffff
pci 0000:00:10.0: PREFETCH window: 0x80000000-0x800fffff
pci 0000:00:02.0: setting latency timer to 64
pci 0000:00:04.0: setting latency timer to 64
pci 0000:00:05.0: setting latency timer to 64
pci 0000:00:06.0: setting latency timer to 64
pci 0000:00:07.0: setting latency timer to 64
pci 0000:00:10.0: setting latency timer to 64
pci_bus 0000:00: resource 0 io: [0x00-0xffff]
pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
pci_bus 0000:01: resource 0 io: [0xa000-0xafff]
pci_bus 0000:01: resource 1 mem: [0xd0000000-0xd2ffffff]
pci_bus 0000:01: resource 2 pref mem [0xc0000000-0xcfffffff]
pci_bus 0000:06: resource 0 io: [0xb000-0xbfff]
pci_bus 0000:06: resource 1 mem: [0xd3000000-0xd4ffffff]
pci_bus 0000:06: resource 2 pref mem [0x80000000-0x800fffff]
pci_bus 0000:06: resource 3 io: [0x00-0xffff]
pci_bus 0000:06: resource 4 mem: [0x000000-0xffffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
pci 0000:01:00.0: Boot video device
Trying to unpack rootfs image as initramfs...
Freeing initrd memory: 20717k freed
PM: Adding info for No Bus:mcelog
PM: Adding info for No Bus:msr0
PM: Adding info for No Bus:msr1
PM: Adding info for platform:pcspkr
PM: Adding info for No Bus:snapshot
highmem bounce pool size: 64 pages
ROMFS MTD (C) 2007 Red Hat, Inc.
msgmni has been set to 1733
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
pcieport 0000:00:02.0: setting latency timer to 64
PM: Adding info for pci_express:0000:00:02.0:pcie08
pcieport 0000:00:04.0: setting latency timer to 64
PM: Adding info for pci_express:0000:00:04.0:pcie08
pcieport 0000:00:05.0: setting latency timer to 64
PM: Adding info for pci_express:0000:00:05.0:pcie08
pcieport 0000:00:06.0: setting latency timer to 64
PM: Adding info for pci_express:0000:00:06.0:pcie08
pcieport 0000:00:07.0: setting latency timer to 64
PM: Adding info for pci_express:0000:00:07.0:pcie08
PM: Adding info for No Bus:pnp1
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
PM: Adding info for No Bus:tty
PM: Adding info for No Bus:console
PM: Adding info for No Bus:tty0
PM: Adding info for No Bus:vcs
PM: Adding info for No Bus:vcsa
PM: Adding info for No Bus:vcs1
PM: Adding info for No Bus:vcsa1
PM: Adding info for No Bus:tty1
PM: Adding info for No Bus:tty2
PM: Adding info for No Bus:tty3
PM: Adding info for No Bus:tty4
PM: Adding info for No Bus:tty5
PM: Adding info for No Bus:tty6
PM: Adding info for No Bus:tty7
PM: Adding info for No Bus:tty8
PM: Adding info for No Bus:tty9
PM: Adding info for No Bus:tty10
PM: Adding info for No Bus:tty11
PM: Adding info for No Bus:tty12
PM: Adding info for No Bus:tty13
PM: Adding info for No Bus:tty14
PM: Adding info for No Bus:tty15
PM: Adding info for No Bus:tty16
PM: Adding info for No Bus:tty17
PM: Adding info for No Bus:tty18
PM: Adding info for No Bus:tty19
PM: Adding info for No Bus:tty20
PM: Adding info for No Bus:tty21
PM: Adding info for No Bus:tty22
PM: Adding info for No Bus:tty23
PM: Adding info for No Bus:tty24
PM: Adding info for No Bus:tty25
PM: Adding info for No Bus:tty26
PM: Adding info for No Bus:tty27
PM: Adding info for No Bus:tty28
PM: Adding info for No Bus:tty29
PM: Adding info for No Bus:tty30
PM: Adding info for No Bus:tty31
PM: Adding info for No Bus:tty32
PM: Adding info for No Bus:tty33
PM: Adding info for No Bus:tty34
PM: Adding info for No Bus:tty35
PM: Adding info for No Bus:tty36
PM: Adding info for No Bus:tty37
PM: Adding info for No Bus:tty38
PM: Adding info for No Bus:tty39
PM: Adding info for No Bus:tty40
PM: Adding info for No Bus:tty41
PM: Adding info for No Bus:tty42
PM: Adding info for No Bus:tty43
PM: Adding info for No Bus:tty44
PM: Adding info for No Bus:tty45
PM: Adding info for No Bus:tty46
PM: Adding info for No Bus:tty47
PM: Adding info for No Bus:tty48
PM: Adding info for No Bus:tty49
PM: Adding info for No Bus:tty50
PM: Adding info for No Bus:tty51
PM: Adding info for No Bus:tty52
PM: Adding info for No Bus:tty53
PM: Adding info for No Bus:tty54
PM: Adding info for No Bus:tty55
PM: Adding info for No Bus:tty56
PM: Adding info for No Bus:tty57
PM: Adding info for No Bus:tty58
PM: Adding info for No Bus:tty59
PM: Adding info for No Bus:tty60
PM: Adding info for No Bus:tty61
PM: Adding info for No Bus:tty62
PM: Adding info for No Bus:tty63
PM: Adding info for No Bus:ptmx
PM: Adding info for No Bus:hpet
PM: Adding info for No Bus:isa
PM: Adding info for No Bus:ram0
PM: Adding info for No Bus:1:0
PM: Adding info for No Bus:ram1
PM: Adding info for No Bus:1:1
PM: Adding info for No Bus:ram2
PM: Adding info for No Bus:1:2
PM: Adding info for No Bus:ram3
PM: Adding info for No Bus:1:3
PM: Adding info for No Bus:ram4
PM: Adding info for No Bus:1:4
PM: Adding info for No Bus:ram5
PM: Adding info for No Bus:1:5
PM: Adding info for No Bus:ram6
PM: Adding info for No Bus:1:6
PM: Adding info for No Bus:ram7
PM: Adding info for No Bus:1:7
PM: Adding info for No Bus:ram8
PM: Adding info for No Bus:1:8
PM: Adding info for No Bus:ram9
PM: Adding info for No Bus:1:9
PM: Adding info for No Bus:ram10
PM: Adding info for No Bus:1:10
PM: Adding info for No Bus:ram11
PM: Adding info for No Bus:1:11
PM: Adding info for No Bus:ram12
PM: Adding info for No Bus:1:12
PM: Adding info for No Bus:ram13
PM: Adding info for No Bus:1:13
PM: Adding info for No Bus:ram14
PM: Adding info for No Bus:1:14
PM: Adding info for No Bus:ram15
PM: Adding info for No Bus:1:15
brd: module loaded
PNP: No PS/2 controller found. Probing ports directly.
PM: Adding info for platform:i8042
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
PM: Adding info for serio:serio0
PM: Adding info for serio:serio1
PM: Adding info for No Bus:mice
PM: Adding info for No Bus:psaux
mice: PS/2 mouse device common for all mice
PM: Adding info for platform:eisa.0
EISA: Probing bus 0 at eisa.0
PM: Removing info for platform:eisa.0
cpuidle: using governor ladder
TCP cubic registered
Using IPI No-Shortcut mode
PM: Adding info for No Bus:cpu_dma_latency
PM: Adding info for No Bus:network_latency
PM: Adding info for No Bus:network_throughput
PM: Checking image partition /dev/hda6
PM: Resume from disk failed.
Magic number: 5:569:475
Freeing unused kernel memory: 404k freed
NET: Registered protocol family 1
PM: Adding info for No Bus:cooling_device0
fan PNP0C0B:00: registered as cooling_device0
ACPI: Fan [FAN] (on)
PM: Adding info for No Bus:thermal_zone0
thermal LNXTHERM:01: registered as thermal_zone0
ACPI: Thermal Zone [THRM] (40 C)
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
SCSI subsystem initialized
Uniform Multi-Platform E-IDE driver
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci_hcd: block sizes: ed 64 td 64
ACPI: PCI Interrupt Link [APCF] enabled at IRQ 23
ohci_hcd 0000:00:0b.0: PCI INT A -> Link[APCF] -> GSI 23 (level, low) -> IRQ 23
ohci_hcd 0000:00:0b.0: setting latency timer to 64
ohci_hcd 0000:00:0b.0: OHCI Host Controller
drivers/usb/core/inode.c: creating file 'devices'
drivers/usb/core/inode.c: creating file '001'
ohci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:0b.0: created debug files
ohci_hcd 0000:00:0b.0: supports USB remote wakeup
ohci_hcd 0000:00:0b.0: irq 23, io mem 0xd5006000
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Warning! ehci_hcd should always be loaded before uhci_hcd and ohci_hcd, not after
ehci_hcd: block sizes: qh 60 qtd 96 itd 160 sitd 96
libata version 3.00 loaded.
ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16
ohci1394 0000:06:06.0: PCI INT A -> Link[APC1] -> GSI 16 (level, low) -> IRQ 16
PM: Adding info for ieee1394:fw-host0
PM: Adding info for No Bus:fw-host0
ohci_hcd 0000:00:0b.0: OHCI controller state
ohci_hcd 0000:00:0b.0: OHCI 1.0, NO legacy support registers
ohci_hcd 0000:00:0b.0: control 0x683 RWE RWC HCFS=operational CBSR=3
ohci_hcd 0000:00:0b.0: cmdstatus 0x00000 SOC=0
ohci_hcd 0000:00:0b.0: intrstatus 0x00000044 RHSC SF
ohci_hcd 0000:00:0b.0: intrenable 0x8000000a MIE RD WDH
ohci_hcd 0000:00:0b.0: hcca frame #0003
ohci_hcd 0000:00:0b.0: roothub.a 01000208 POTPGT=1 NPS NDP=8(8)
ohci_hcd 0000:00:0b.0: roothub.b 00000000 PPCM=0000 DR=0000
ohci_hcd 0000:00:0b.0: roothub.status 00008000 DRWE
ohci_hcd 0000:00:0b.0: roothub.portstatus [0] 0x00010301 CSC LSDA PPS CCS
ohci_hcd 0000:00:0b.0: roothub.portstatus [1] 0x00010101 CSC PPS CCS
ohci_hcd 0000:00:0b.0: roothub.portstatus [2] 0x00010101 CSC PPS CCS
ohci_hcd 0000:00:0b.0: roothub.portstatus [3] 0x00000100 PPS
ohci_hcd 0000:00:0b.0: roothub.portstatus [4] 0x00000100 PPS
ohci_hcd 0000:00:0b.0: roothub.portstatus [5] 0x00010101 CSC PPS CCS
ohci_hcd 0000:00:0b.0: roothub.portstatus [6] 0x00000100 PPS
ohci_hcd 0000:00:0b.0: roothub.portstatus [7] 0x00000100 PPS
usb usb1: default language 0x0409
usb usb1: udev 1, busnum 1, minor = 0
usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: OHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.32 ohci_hcd
usb usb1: SerialNumber: 0000:00:0b.0
PM: Adding info for usb:usb1
usb usb1: uevent
usb usb1: usb_probe_device
usb usb1: configuration #1 chosen from 1 choice
usb usb1: adding 1-0:1.0 (config #1, interface 0)
PM: Adding info for usb:1-0:1.0
usb 1-0:1.0: uevent
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: no power switching (usb 1.0)
hub 1-0:1.0: global over-current protection
hub 1-0:1.0: power on to power good time: 2ms
hub 1-0:1.0: local power source is good
hub 1-0:1.0: no over-current condition exists
hub 1-0:1.0: trying to enable port power on non-switchable hub
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev1.1
drivers/usb/core/inode.c: creating file '001'
PM: Adding info for No Bus:ep_00
ACPI: PCI Interrupt Link [APCL] enabled at IRQ 22
ehci_hcd 0000:00:0b.1: PCI INT B -> Link[APCL] -> GSI 22 (level, low) -> IRQ 22
ehci_hcd 0000:00:0b.1: setting latency timer to 64
ehci_hcd 0000:00:0b.1: EHCI Host Controller
drivers/usb/core/inode.c: creating file '002'
ehci_hcd 0000:00:0b.1: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:0b.1: reset hcs_params 0x101888 dbg=1 cc=1 pcc=8 !ppc ports=8
ehci_hcd 0000:00:0b.1: reset portroute 0 0 0 0 0 0 0 0
ehci_hcd 0000:00:0b.1: reset hcc_params a086 caching frame 256/512/1024 park
ehci_hcd 0000:00:0b.1: park 0
ehci_hcd 0000:00:0b.1: debug port 1
ehci_hcd 0000:00:0b.1: reset command 080b02 park=3 ithresh=8 period=1024 Reset HALT
ehci_hcd 0000:00:0b.1: cache line size of 32 is not supported
ehci_hcd 0000:00:0b.1: supports USB remote wakeup
ehci_hcd 0000:00:0b.1: irq 22, io mem 0xd5007000
ehci_hcd 0000:00:0b.1: reset command 080b02 park=3 ithresh=8 period=1024 Reset HALT
ehci_hcd 0000:00:0b.1: init command 010009 (park)=0 ithresh=1 period=256 RUN
usb usb1: uevent
usb usb1: uevent
ehci_hcd 0000:00:0b.1: USB 2.0 started, EHCI 1.00
usb usb2: default language 0x0409
usb usb2: udev 1, busnum 2, minor = 128
usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: EHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.32 ehci_hcd
usb usb2: SerialNumber: 0000:00:0b.1
PM: Adding info for usb:usb2
usb usb2: uevent
usb usb2: usb_probe_device
usb usb2: configuration #1 chosen from 1 choice
usb usb2: adding 2-0:1.0 (config #1, interface 0)
PM: Adding info for usb:2-0:1.0
usb 2-0:1.0: uevent
hub 2-0:1.0: usb_probe_interface
hub 2-0:1.0: usb_probe_interface - got id
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 8 ports detected
hub 2-0:1.0: standalone hub
hub 2-0:1.0: no power switching (usb 1.0)
hub 2-0:1.0: individual port over-current protection
hub 2-0:1.0: power on to power good time: 20ms
hub 2-0:1.0: local power source is good
hub 2-0:1.0: trying to enable port power on non-switchable hub
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev2.1
drivers/usb/core/inode.c: creating file '001'
PM: Adding info for No Bus:ep_00
amd74xx 0000:00:0d.0: UDMA133 controller
amd74xx 0000:00:0d.0: IDE controller (0x10de:0x0265 rev 0xa1)
amd74xx 0000:00:0d.0: IDE port disabled
amd74xx 0000:00:0d.0: BIOS didn't set cable bits correctly. Enabling workaround.
amd74xx 0000:00:0d.0: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xf008-0xf00f
Probing IDE interface ide0...
usb usb2: uevent
usb usb2: uevent
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[16] MMIO=[d4001000-d40017ff] Max Packet=[2] IR/IT contexts=[4/8]
ohci1394: fw-host0: Serial EEPROM has suspicious values, attempting to set max_packet_size to 512 bytes
r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17
r8169 0000:06:07.0: PCI INT A -> Link[APC2] -> GSI 17 (level, low) -> IRQ 17
r8169 0000:06:07.0: no PCI Express capability
PM: Adding info for No Bus:eth0
eth0: RTL8169sb/8110sb at 0xf8d46000, 00:14:d1:1a:ac:15, XID 10000000 IRQ 17
udev: renamed network interface eth0 to eth1
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00010300 CSC LSDA PPS
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [1] = 0x00010100 CSC PPS
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [2] = 0x00010100 CSC PPS
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [5] = 0x00010100 CSC PPS
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 2-0:1.0: port 1: status 0501 change 0001
ehci_hcd 0000:00:0b.1: GetStatus port 2 status 001803 POWER sig=j CSC CONNECT
hub 2-0:1.0: port 2: status 0501 change 0001
ehci_hcd 0000:00:0b.1: GetStatus port 3 status 001803 POWER sig=j CSC CONNECT
hub 2-0:1.0: port 3: status 0501 change 0001
ehci_hcd 0000:00:0b.1: GetStatus port 6 status 001803 POWER sig=j CSC CONNECT
hub 2-0:1.0: port 6: status 0501 change 0001
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0000
hub 2-0:1.0: state 7 ports 8 chg 004e evt 0000
hub 2-0:1.0: port 1, status 0501, change 0000, 480 Mb/s
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 2-0:1.0: port 2, status 0501, change 0000, 480 Mb/s
ehci_hcd 0000:00:0b.1: port 2 high speed
ehci_hcd 0000:00:0b.1: GetStatus port 2 status 001005 POWER sig=se0 PE CONNECT
usb 2-2: new high speed USB device using ehci_hcd and address 3
ehci_hcd 0000:00:0b.1: port 2 high speed
ehci_hcd 0000:00:0b.1: GetStatus port 2 status 001005 POWER sig=se0 PE CONNECT
usb 2-2: default language 0x0409
ehci_hcd 0000:00:0b.1: detected XactErr len 0/8 retry 1
ehci_hcd 0000:00:0b.1: detected XactErr len 0/8 retry 1
usb 2-2: udev 3, busnum 2, minor = 130
usb 2-2: New USB device found, idVendor=058f, idProduct=6362
usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-2: Product: Mass Storage Device
usb 2-2: Manufacturer: Generic
usb 2-2: SerialNumber: 058F312D81B
PM: Adding info for usb:2-2
usb 2-2: uevent
usb 2-2: usb_probe_device
usb 2-2: configuration #1 chosen from 1 choice
usb 2-2: adding 2-2:1.0 (config #1, interface 0)
PM: Adding info for usb:2-2:1.0
usb 2-2:1.0: uevent
PM: Adding info for No Bus:ep_01
PM: Adding info for No Bus:ep_82
PM: Adding info for No Bus:usbdev2.3
drivers/usb/core/inode.c: creating file '003'
PM: Adding info for No Bus:ep_00
hub 2-0:1.0: port 3, status 0501, change 0000, 480 Mb/s
usb 2-2: uevent
usb 2-2: uevent
Initializing USB Mass Storage driver...
usb-storage 2-2:1.0: usb_probe_interface
usb-storage 2-2:1.0: usb_probe_interface - got id
scsi0 : SCSI emulation for USB Mass Storage devices
PM: Adding info for scsi:host0
PM: Adding info for No Bus:host0
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
ehci_hcd 0000:00:0b.1: port 3 high speed
ehci_hcd 0000:00:0b.1: GetStatus port 3 status 001005 POWER sig=se0 PE CONNECT
usb 2-3: new high speed USB device using ehci_hcd and address 4
ehci_hcd 0000:00:0b.1: port 3 high speed
ehci_hcd 0000:00:0b.1: GetStatus port 3 status 001005 POWER sig=se0 PE CONNECT
hda: PIONEER DVD-RW DVR-111D, ATAPI CD/DVD-ROM drive
usb 2-3: udev 4, busnum 2, minor = 131
usb 2-3: New USB device found, idVendor=0409, idProduct=0059
usb 2-3: New USB device strings: Mfr=0, Product=0, SerialNumber=0
PM: Adding info for usb:2-3
usb 2-3: uevent
usb 2-3: usb_probe_device
usb 2-3: configuration #1 chosen from 1 choice
usb 2-3: adding 2-3:1.0 (config #1, interface 0)
PM: Adding info for usb:2-3:1.0
usb 2-3:1.0: uevent
hub 2-3:1.0: usb_probe_interface
hub 2-3:1.0: usb_probe_interface - got id
hub 2-3:1.0: USB hub found
hub 2-3:1.0: 4 ports detected
hub 2-3:1.0: standalone hub
hub 2-3:1.0: individual port power switching
hub 2-3:1.0: individual port over-current protection
hub 2-3:1.0: Single TT
hub 2-3:1.0: TT requires at most 16 FS bit times (1332 ns)
hub 2-3:1.0: Port indicators are supported
hub 2-3:1.0: power on to power good time: 100ms
hub 2-3:1.0: local power source is good
hub 2-3:1.0: enabling power on all ports
usb 2-3: uevent
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev2.4
drivers/usb/core/inode.c: creating file '004'
PM: Adding info for No Bus:ep_00
hub 2-0:1.0: port 6, status 0501, change 0000, 480 Mb/s
usb 2-3: uevent
ehci_hcd 0000:00:0b.1: port 6 high speed
ehci_hcd 0000:00:0b.1: GetStatus port 6 status 001005 POWER sig=se0 PE CONNECT
hub 2-3:1.0: port 3: status 0101 change 0001
usb 2-6: new high speed USB device using ehci_hcd and address 5
ehci_hcd 0000:00:0b.1: port 6 high speed
ehci_hcd 0000:00:0b.1: GetStatus port 6 status 001005 POWER sig=se0 PE CONNECT
usb 2-3: link qh256-0001/c1cfb1c0 start 1 [1/0 us]
usb 2-6: default language 0x0409
usb 2-6: udev 5, busnum 2, minor = 132
usb 2-6: New USB device found, idVendor=05e3, idProduct=0605
usb 2-6: New USB device strings: Mfr=0, Product=1, SerialNumber=0
usb 2-6: Product: USB2.0 Hub
PM: Adding info for usb:2-6
usb 2-6: uevent
usb 2-6: usb_probe_device
usb 2-6: configuration #1 chosen from 1 choice
usb 2-6: adding 2-6:1.0 (config #1, interface 0)
PM: Adding info for usb:2-6:1.0
usb 2-6:1.0: uevent
hub 2-6:1.0: usb_probe_interface
hub 2-6:1.0: usb_probe_interface - got id
hub 2-6:1.0: USB hub found
usb 2-6: uevent
hub 2-6:1.0: 4 ports detected
hub 2-6:1.0: standalone hub
hub 2-6:1.0: individual port power switching
hub 2-6:1.0: individual port over-current protection
hub 2-6:1.0: Single TT
hub 2-6:1.0: TT requires at most 32 FS bit times (2664 ns)
hub 2-6:1.0: Port indicators are supported
hub 2-6:1.0: power on to power good time: 100ms
hub 2-6:1.0: local power source is good
hub 2-6:1.0: enabling power on all ports
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev2.5
drivers/usb/core/inode.c: creating file '005'
PM: Adding info for No Bus:ep_00
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00010301 CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0001, 1.5 Mb/s
usb 2-6: uevent
hub 2-6:1.0: port 1: status 0101 change 0001
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-3:1.0: state 7 ports 4 chg 0008 evt 0000
hub 2-3:1.0: port 3, status 0101, change 0000, 12 Mb/s
hub 2-3:1.0: port 3 not reset yet, waiting 10ms
usb 2-6: link qh256-0001/c1cfb380 start 2 [1/0 us]
usb 2-3.3: new full speed USB device using ehci_hcd and address 6
hub 2-3:1.0: port 3 not reset yet, waiting 10ms
usb 2-3.3: ep0 maxpacket = 8
usb 2-3.3: default language 0x0409
usb 2-3.3: udev 6, busnum 2, minor = 133
usb 2-3.3: New USB device found, idVendor=05e3, idProduct=0604
usb 2-3.3: New USB device strings: Mfr=0, Product=1, SerialNumber=0
usb 2-3.3: Product: USB Hub
PM: Adding info for usb:2-3.3
usb 2-3.3: uevent
usb 2-3.3: usb_probe_device
usb 2-3.3: configuration #1 chosen from 1 choice
usb 2-3.3: adding 2-3.3:1.0 (config #1, interface 0)
PM: Adding info for usb:2-3.3:1.0
usb 2-3.3:1.0: uevent
hub 2-3.3:1.0: usb_probe_interface
hub 2-3.3:1.0: usb_probe_interface - got id
hub 2-3.3:1.0: USB hub found
usb 2-3.3: uevent
hub 2-3.3:1.0: 4 ports detected
hub 2-3.3:1.0: standalone hub
hub 2-3.3:1.0: individual port power switching
hub 2-3.3:1.0: individual port over-current protection
hub 2-3.3:1.0: power on to power good time: 100ms
hub 2-3.3:1.0: local power source is good
hub 2-3.3:1.0: enabling power on all ports
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev2.6
drivers/usb/core/inode.c: creating file '006'
PM: Adding info for No Bus:ep_00
hub 2-6:1.0: state 7 ports 4 chg 0002 evt 0000
usb 2-3.3: uevent
hub 2-6:1.0: port 1, status 0101, change 0000, 12 Mb/s
PM: Adding info for No Bus:ide0
PM: Adding info for No Bus:ide0
hda: host max PIO5 wanted PIO255(auto-tune) selected PIO4
hda: UDMA/66 mode selected
PM: Adding info for ieee1394:001106000000bd66
PM: Adding info for No Bus:001106000000bd66
ieee1394: Host added: ID:BUS[0-00:1023] GUID[001106000000bd66]
ide0 at 0x170-0x177,0x376 on irq 15
PM: Adding info for ide:0.0
sata_nv 0000:00:0e.0: version 3.5
ACPI: PCI Interrupt Link [APSI] enabled at IRQ 21
sata_nv 0000:00:0e.0: PCI INT A -> Link[APSI] -> GSI 21 (level, low) -> IRQ 21
sata_nv 0000:00:0e.0: Using SWNCQ mode
sata_nv 0000:00:0e.0: setting latency timer to 64
scsi1 : sata_nv
PM: Adding info for scsi:host1
PM: Adding info for No Bus:host1
scsi2 : sata_nv
PM: Adding info for scsi:host2
PM: Adding info for No Bus:host2
ata1: SATA max UDMA/133 cmd 0x9f0 ctl 0xbf0 bmdma 0xd400 irq 21
ata2: SATA max UDMA/133 cmd 0x970 ctl 0xb70 bmdma 0xd408 irq 21
ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 20
sata_nv 0000:00:0f.0: PCI INT A -> Link[APSJ] -> GSI 20 (level, low) -> IRQ 20
sata_nv 0000:00:0f.0: Using SWNCQ mode
sata_nv 0000:00:0f.0: setting latency timer to 64
scsi3 : sata_nv
PM: Adding info for scsi:host3
PM: Adding info for No Bus:host3
scsi4 : sata_nv
PM: Adding info for scsi:host4
PM: Adding info for No Bus:host4
ata3: SATA max UDMA/133 cmd 0x9e0 ctl 0xbe0 bmdma 0xe800 irq 20
ata4: SATA max UDMA/133 cmd 0x960 ctl 0xb60 bmdma 0xe808 irq 20
PM: Adding info for ieee1394:001a66fffee31809
PM: Adding info for No Bus:001a66fffee31809
ieee1394: Node added: ID:BUS[0-01:1023] GUID[001a66fffee31809]
PM: Adding info for ieee1394:001a66fffee31809-0
PM: Adding info for No Bus:001a66fffee31809-0
PM: Adding info for ieee1394:001a66fffee31809-1
PM: Adding info for No Bus:001a66fffee31809-1
usb 2-6.1: new high speed USB device using ehci_hcd and address 7
hub 2-3.3:1.0: port 3: status 0301 change 0001
usb 2-6.1: udev 7, busnum 2, minor = 134
usb 2-6.1: New USB device found, idVendor=0409, idProduct=0059
usb 2-6.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
PM: Adding info for usb:2-6.1
usb 2-6.1: uevent
usb 2-6.1: usb_probe_device
usb 2-6.1: configuration #1 chosen from 1 choice
usb 2-6.1: adding 2-6.1:1.0 (config #1, interface 0)
PM: Adding info for usb:2-6.1:1.0
usb 2-6.1:1.0: uevent
hub 2-6.1:1.0: usb_probe_interface
hub 2-6.1:1.0: usb_probe_interface - got id
hub 2-6.1:1.0: USB hub found
hub 2-6.1:1.0: 4 ports detected
hub 2-6.1:1.0: standalone hub
hub 2-6.1:1.0: individual port power switching
hub 2-6.1:1.0: individual port over-current protection
hub 2-6.1:1.0: Single TT
hub 2-6.1:1.0: TT requires at most 16 FS bit times (1332 ns)
hub 2-6.1:1.0: Port indicators are supported
hub 2-6.1:1.0: power on to power good time: 100ms
usb 2-6.1: uevent
hub 2-6.1:1.0: local power source is good
hub 2-6.1:1.0: enabling power on all ports
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev2.7
drivers/usb/core/inode.c: creating file '007'
PM: Adding info for No Bus:ep_00
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030300 PESC CSC LSDA PPS
hub 1-0:1.0: port 1, status 0300, change 0003, 1.5 Mb/s
usb 2-6.1: uevent
usb 2-3.3: link qh128-0e01/c1cfbf40 start 3 [1/2 us]
hub 2-6.1:1.0: port 1: status 0301 change 0001
hub 2-6.1:1.0: port 2: status 0101 change 0001
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x300
hub 2-6:1.0: state 7 ports 4 chg 0000 evt 0002
hub 2-3.3:1.0: state 7 ports 4 chg 0008 evt 0000
hub 2-3.3:1.0: port 3, status 0301, change 0000, 1.5 Mb/s
usb 2-3.3.3: new low speed USB device using ehci_hcd and address 8
hub 2-3.3:1.0: port 3 not reset yet, waiting 10ms
usb 2-6.1: link qh256-0001/c1cfbf80 start 4 [1/0 us]
usb 2-3.3.3: skipped 1 descriptor after interface
usb 2-3.3.3: skipped 1 descriptor after interface
usb 2-3.3.3: default language 0x0409
usb 2-3.3.3: udev 8, busnum 2, minor = 135
usb 2-3.3.3: New USB device found, idVendor=2222, idProduct=0013
usb 2-3.3.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 2-3.3.3: Product: Macally iKeySlim
usb 2-3.3.3: Manufacturer: Macally Peripherals
PM: Adding info for usb:2-3.3.3
usb 2-3.3.3: uevent
usb 2-3.3.3: usb_probe_device
usb 2-3.3.3: configuration #1 chosen from 1 choice
usb 2-3.3.3: uevent
usb 2-3.3.3: adding 2-3.3.3:1.0 (config #1, interface 0)
PM: Adding info for usb:2-3.3.3:1.0
usb 2-3.3.3:1.0: uevent
PM: Adding info for No Bus:ep_81
usb 2-3.3.3: adding 2-3.3.3:1.1 (config #1, interface 1)
PM: Adding info for usb:2-3.3.3:1.1
usb 2-3.3.3:1.1: uevent
PM: Adding info for No Bus:ep_82
PM: Adding info for No Bus:usbdev2.8
drivers/usb/core/inode.c: creating file '008'
PM: Adding info for No Bus:ep_00
hub 2-3.3:1.0: state 7 ports 4 chg 0000 evt 0008
usb 2-3.3.3: uevent
hub 2-6.1:1.0: state 7 ports 4 chg 0006 evt 0000
hub 2-6.1:1.0: port 1, status 0301, change 0000, 1.5 Mb/s
usbcore: registered new interface driver hiddev
usbhid 2-3.3.3:1.0: usb_probe_interface
usbhid 2-3.3.3:1.0: usb_probe_interface - got id
PM: Adding info for hid:0003:2222:0013.0001
PM: Adding info for No Bus:input0
input: Macally Peripherals Macally iKeySlim as /devices/pci0000:00/0000:00:0b.1/usb2/2-3/2-3.3/2-3.3.3/2-3.3.3:1.0/input/input0
usb 2-3.3.3: link qh8-0e01/c1d95100 start 5 [1/2 us]
generic-usb 0003:2222:0013.0001: input: USB HID v1.10 Keyboard [Macally Peripherals Macally iKeySlim] on usb-0000:00:0b.1-3.3.3/input0
usbhid 2-3.3.3:1.1: usb_probe_interface
usbhid 2-3.3.3:1.1: usb_probe_interface - got id
PM: Adding info for hid:0003:2222:0013.0002
hub 2-6.1:1.0: port 1 not reset yet, waiting 10ms
PM: Adding info for No Bus:input1
input: Macally Peripherals Macally iKeySlim as /devices/pci0000:00/0000:00:0b.1/usb2/2-3/2-3.3/2-3.3.3/2-3.3.3:1.1/input/input1
usb 2-3.3.3: link qh8-0e01/c1d95200 start 6 [1/2 us]
PM: Adding info for No Bus:mouse0
generic-usb 0003:2222:0013.0002: input: USB HID v1.10 Mouse [Macally Peripherals Macally iKeySlim] on usb-0000:00:0b.1-3.3.3/input1
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
usb 2-6.1.1: new low speed USB device using ehci_hcd and address 9
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: ATAPI: ATAPI iHOS104, WL08, max UDMA/100
ata1.00: ATA-7: SAMSUNG SP2504C, VT100-41, max UDMA7
ata1.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32)
hub 2-6.1:1.0: port 1 not reset yet, waiting 10ms
ata3.00: configured for UDMA/100
ata1.00: configured for UDMA/133
scsi 1:0:0:0: Direct-Access ATA SAMSUNG SP2504C VT10 PQ: 0 ANSI: 5
PM: Adding info for scsi:target1:0:0
PM: Adding info for scsi:1:0:0:0
PM: Adding info for No Bus:1:0:0:0
PM: Adding info for No Bus:1:0:0:0
usb 2-6.1.1: skipped 1 descriptor after interface
usb 2-6.1.1: skipped 1 descriptor after interface
usb 2-6.1.1: default language 0x0409
usb 2-6.1.1: udev 9, busnum 2, minor = 136
usb 2-6.1.1: New USB device found, idVendor=10d5, idProduct=0004
usb 2-6.1.1: New USB device strings: Mfr=0, Product=2, SerialNumber=0
usb 2-6.1.1: Product: PS2 to USB AdapterA3
PM: Adding info for usb:2-6.1.1
usb 2-6.1.1: uevent
usb 2-6.1.1: usb_probe_device
usb 2-6.1.1: configuration #1 chosen from 1 choice
usb 2-6.1.1: uevent
usb 2-6.1.1: adding 2-6.1.1:1.0 (config #1, interface 0)
PM: Adding info for usb:2-6.1.1:1.0
usb 2-6.1.1:1.0: uevent
usbhid 2-6.1.1:1.0: usb_probe_interface
usbhid 2-6.1.1:1.0: usb_probe_interface - got id
PM: Adding info for hid:0003:10D5:0004.0003
PM: Adding info for No Bus:input2
input: PS2 to USB AdapterA3 as /devices/pci0000:00/0000:00:0b.1/usb2/2-6/2-6.1/2-6.1.1/2-6.1.1:1.0/input/input2
usb 2-6.1.1: link qh8-0e01/c1d955c0 start 7 [1/2 us]
generic-usb 0003:10D5:0004.0003: input: USB HID v1.10 Keyboard [PS2 to USB AdapterA3] on usb-0000:00:0b.1-6.1.1/input0
PM: Adding info for No Bus:ep_81
usb 2-6.1.1: adding 2-6.1.1:1.1 (config #1, interface 1)
PM: Adding info for usb:2-6.1.1:1.1
usb 2-6.1.1:1.1: uevent
usbhid 2-6.1.1:1.1: usb_probe_interface
usbhid 2-6.1.1:1.1: usb_probe_interface - got id
PM: Adding info for hid:0003:10D5:0004.0004
PM: Adding info for No Bus:input3
input: PS2 to USB AdapterA3 as /devices/pci0000:00/0000:00:0b.1/usb2/2-6/2-6.1/2-6.1.1/2-6.1.1:1.1/input/input3
usb 2-6.1.1: link qh8-0e01/c1d95680 start 0 [1/2 us]
PM: Adding info for No Bus:mouse1
generic-usb 0003:10D5:0004.0004: input: USB HID v1.10 Mouse [PS2 to USB AdapterA3] on usb-0000:00:0b.1-6.1.1/input1
PM: Adding info for No Bus:ep_82
PM: Adding info for No Bus:usbdev2.9
drivers/usb/core/inode.c: creating file '009'
PM: Adding info for No Bus:ep_00
usb 2-6.1.1: uevent
hub 2-6.1:1.0: port 2, status 0101, change 0000, 12 Mb/s
hub 2-6.1:1.0: port 2 not reset yet, waiting 10ms
usb 2-6.1.2: new high speed USB device using ehci_hcd and address 10
hub 2-6.1:1.0: port 2 not reset yet, waiting 10ms
usb 2-6.1.2: default language 0x0409
usb 2-6.1.2: udev 10, busnum 2, minor = 137
usb 2-6.1.2: New USB device found, idVendor=05e3, idProduct=0605
usb 2-6.1.2: New USB device strings: Mfr=0, Product=1, SerialNumber=0
usb 2-6.1.2: Product: USB2.0 Hub
PM: Adding info for usb:2-6.1.2
usb 2-6.1.2: uevent
usb 2-6.1.2: usb_probe_device
usb 2-6.1.2: configuration #1 chosen from 1 choice
usb 2-6.1.2: adding 2-6.1.2:1.0 (config #1, interface 0)
PM: Adding info for usb:2-6.1.2:1.0
usb 2-6.1.2:1.0: uevent
hub 2-6.1.2:1.0: usb_probe_interface
hub 2-6.1.2:1.0: usb_probe_interface - got id
hub 2-6.1.2:1.0: USB hub found
hub 2-6.1.2:1.0: 4 ports detected
hub 2-6.1.2:1.0: standalone hub
hub 2-6.1.2:1.0: individual port power switching
hub 2-6.1.2:1.0: individual port over-current protection
hub 2-6.1.2:1.0: Single TT
hub 2-6.1.2:1.0: TT requires at most 32 FS bit times (2664 ns)
hub 2-6.1.2:1.0: Port indicators are supported
hub 2-6.1.2:1.0: power on to power good time: 100ms
usb 2-6.1.2: uevent
hub 2-6.1.2:1.0: local power source is good
hub 2-6.1.2:1.0: enabling power on all ports
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev2.10
drivers/usb/core/inode.c: creating file '010'
PM: Adding info for No Bus:ep_00
hub 2-3.3:1.0: state 7 ports 4 chg 0000 evt 0002
usb 2-6.1.2: uevent
hub 2-3.3:1.0: port 1, status 0301, change 0001, 1.5 Mb/s
hub 2-6.1.2:1.0: port 1: status 0101 change 0001
hub 2-6.1.2:1.0: port 2: status 0301 change 0001
hub 2-3.3:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
usb 2-3.3.1: new low speed USB device using ehci_hcd and address 11
usb 2-6.1.2: link qh256-0001/c1d957c0 start 9 [1/0 us]
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
usb 2-3.3.1: skipped 1 descriptor after interface
usb 2-3.3.1: default language 0x0409
usb 2-3.3.1: udev 11, busnum 2, minor = 138
usb 2-3.3.1: New USB device found, idVendor=2222, idProduct=3100
usb 2-3.3.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 2-3.3.1: Product: Macally ECOMouse
usb 2-3.3.1: Manufacturer: Macally Peripherals
PM: Adding info for usb:2-3.3.1
usb 2-3.3.1: uevent
usb 2-3.3.1: usb_probe_device
usb 2-3.3.1: configuration #1 chosen from 1 choice
usb 2-3.3.1: adding 2-3.3.1:1.0 (config #1, interface 0)
PM: Adding info for usb:2-3.3.1:1.0
usb 2-3.3.1:1.0: uevent
usbhid 2-3.3.1:1.0: usb_probe_interface
usbhid 2-3.3.1:1.0: usb_probe_interface - got id
PM: Adding info for hid:0003:2222:3100.0005
usb 2-3.3.1: uevent
ata2.00: ATA-7: ST3250620AS, 3.AAC, max UDMA/133
ata2.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32)
PM: Adding info for No Bus:input4
input: Macally Peripherals Macally ECOMouse as /devices/pci0000:00/0000:00:0b.1/usb2/2-3/2-3.3/2-3.3.1/2-3.3.1:1.0/input/input4
PM: Adding info for No Bus:mouse2
generic-usb 0003:2222:3100.0005: input: USB HID v1.00 Mouse [Macally Peripherals Macally ECOMouse ] on usb-0000:00:0b.1-3.3.1/input0
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev2.11
drivers/usb/core/inode.c: creating file '011'
PM: Adding info for No Bus:ep_00
hub 2-6.1:1.0: state 7 ports 4 chg 0000 evt 0002
usb 2-3.3.1: uevent
hub 2-3.3:1.0: state 7 ports 4 chg 0000 evt 0002
hub 2-6.1.2:1.0: state 7 ports 4 chg 0006 evt 0000
hub 2-6.1.2:1.0: port 1, status 0101, change 0000, 12 Mb/s
usb 2-6.1.2.1: new high speed USB device using ehci_hcd and address 12
ata2.00: configured for UDMA/133
scsi 2:0:0:0: Direct-Access ATA ST3250620AS 3.AA PQ: 0 ANSI: 5
PM: Adding info for scsi:target2:0:0
PM: Adding info for scsi:2:0:0:0
PM: Adding info for No Bus:2:0:0:0
PM: Adding info for No Bus:2:0:0:0
hub 2-6.1.2:1.0: port 1 not reset yet, waiting 10ms
usb 2-6.1.2.1: default language 0x0409
usb 2-6.1.2.1: udev 12, busnum 2, minor = 139
usb 2-6.1.2.1: New USB device found, idVendor=090c, idProduct=1000
usb 2-6.1.2.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-6.1.2.1: Product: DISK 2.0
usb 2-6.1.2.1: Manufacturer: USB
usb 2-6.1.2.1: SerialNumber: PHN84K6AD8PLXSVC
PM: Adding info for usb:2-6.1.2.1
usb 2-6.1.2.1: uevent
usb 2-6.1.2.1: usb_probe_device
usb 2-6.1.2.1: configuration #1 chosen from 1 choice
usb 2-6.1.2.1: adding 2-6.1.2.1:1.0 (config #1, interface 0)
PM: Adding info for usb:2-6.1.2.1:1.0
usb 2-6.1.2.1:1.0: uevent
usb-storage 2-6.1.2.1:1.0: usb_probe_interface
usb-storage 2-6.1.2.1:1.0: usb_probe_interface - got id
scsi5 : SCSI emulation for USB Mass Storage devices
PM: Adding info for scsi:host5
PM: Adding info for No Bus:host5
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:ep_02
PM: Adding info for No Bus:usbdev2.12
drivers/usb/core/inode.c: creating file '012'
PM: Adding info for No Bus:ep_00
usb-storage: device found at 12
usb-storage: waiting for device to settle before scanning
usb 2-6.1.2.1: uevent
hub 2-6.1.2:1.0: port 2, status 0301, change 0000, 1.5 Mb/s
usb 2-6.1.2.1: uevent
usb 2-6.1.2.2: new low speed USB device using ehci_hcd and address 13
hub 2-6.1.2:1.0: port 2 not reset yet, waiting 10ms
usb 2-6.1.2.2: skipped 1 descriptor after interface
usb 2-6.1.2.2: default language 0x0409
usb 2-6.1.2.2: udev 13, busnum 2, minor = 140
usb 2-6.1.2.2: New USB device found, idVendor=046d, idProduct=c00c
usb 2-6.1.2.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 2-6.1.2.2: Product: USB Optical Mouse
usb 2-6.1.2.2: Manufacturer: Logitech
PM: Adding info for usb:2-6.1.2.2
usb 2-6.1.2.2: uevent
usb 2-6.1.2.2: usb_probe_device
usb 2-6.1.2.2: configuration #1 chosen from 1 choice
usb 2-6.1.2.2: adding 2-6.1.2.2:1.0 (config #1, interface 0)
PM: Adding info for usb:2-6.1.2.2:1.0
usb 2-6.1.2.2:1.0: uevent
usbhid 2-6.1.2.2:1.0: usb_probe_interface
usbhid 2-6.1.2.2:1.0: usb_probe_interface - got id
PM: Adding info for hid:0003:046D:C00C.0006
usb 2-6.1.2.2: uevent
PM: Adding info for No Bus:input5
input: Logitech USB Optical Mouse as /devices/pci0000:00/0000:00:0b.1/usb2/2-6/2-6.1/2-6.1.2/2-6.1.2.2/2-6.1.2.2:1.0/input/input5
PM: Adding info for No Bus:mouse3
generic-usb 0003:046D:C00C.0006: input: USB HID v1.10 Mouse [Logitech USB Optical Mouse] on usb-0000:00:0b.1-6.1.2.2/input0
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev2.13
drivers/usb/core/inode.c: creating file '013'
PM: Adding info for No Bus:ep_00
hub 2-6.1.2:1.0: state 7 ports 4 chg 0000 evt 0004
usb 2-6.1.2.2: uevent
ohci_hcd 0000:00:0b.0: auto-stop root hub
scsi 0:0:0:0: Direct-Access Generic USB SD Reader 1.00 PQ: 0 ANSI: 0
PM: Adding info for scsi:target0:0:0
PM: Adding info for scsi:0:0:0:0
PM: Adding info for No Bus:0:0:0:0
PM: Adding info for No Bus:0:0:0:0
scsi 0:0:0:1: Direct-Access Generic USB CF Reader 1.01 PQ: 0 ANSI: 0
PM: Adding info for scsi:0:0:0:1
PM: Adding info for No Bus:0:0:0:1
PM: Adding info for No Bus:0:0:0:1
scsi 0:0:0:2: Direct-Access Generic USB SM Reader 1.02 PQ: 0 ANSI: 0
PM: Adding info for scsi:0:0:0:2
PM: Adding info for No Bus:0:0:0:2
PM: Adding info for No Bus:0:0:0:2
scsi 0:0:0:3: Direct-Access Generic USB MS Reader 1.03 PQ: 0 ANSI: 0
PM: Adding info for scsi:0:0:0:3
PM: Adding info for No Bus:0:0:0:3
PM: Adding info for No Bus:0:0:0:3
usb-storage: device scan complete
PM: Adding info for No Bus:1:0:0:0
PM: Adding info for No Bus:2:0:0:0
PM: Adding info for No Bus:0:0:0:0
PM: Adding info for No Bus:0:0:0:1
PM: Adding info for No Bus:0:0:0:2
PM: Adding info for No Bus:0:0:0:3
sd 1:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB)
sd 2:0:0:0: [sdb] 488397168 512-byte logical blocks: (250 GB/232 GiB)
sd 2:0:0:0: [sdb] Write Protect is off
sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
PM: Adding info for No Bus:sdb
sdb:
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
PM: Adding info for No Bus:sda
sda:
PM: Adding info for No Bus:sdc
PM: Adding info for No Bus:8:32
PM: Adding info for No Bus:sdd
PM: Adding info for No Bus:8:48
PM: Adding info for No Bus:sde
PM: Adding info for No Bus:8:64
PM: Adding info for No Bus:sdf
PM: Adding info for No Bus:8:80
sd 0:0:0:0: [sdc] Attached SCSI removable disk
sda1 sda2 sda3 <
sd 0:0:0:1: [sdd] Attached SCSI removable disk
sd 0:0:0:2: [sde] Attached SCSI removable disk
sd 0:0:0:3: [sdf] Attached SCSI removable disk
>
PM: Adding info for No Bus:sda1
PM: Adding info for No Bus:sda2
PM: Adding info for No Bus:sda3
PM: Adding info for No Bus:8:0
sd 1:0:0:0: [sda] Attached SCSI disk
unknown partition table
PM: Adding info for No Bus:8:16
sd 2:0:0:0: [sdb] Attached SCSI disk
ata3.00: qc timeout (cmd 0xa0)
ata3.00: TEST_UNIT_READY failed (err_mask=0x5)
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.00: configured for UDMA/100
scsi 5:0:0:0: Direct-Access USB DISK 2.0 0403 PQ: 0 ANSI: 0 CCS
PM: Adding info for scsi:target5:0:0
PM: Adding info for scsi:5:0:0:0
PM: Adding info for No Bus:5:0:0:0
PM: Adding info for No Bus:5:0:0:0
PM: Adding info for No Bus:5:0:0:0
usb-storage: device scan complete
sd 5:0:0:0: [sdg] 3981312 512-byte logical blocks: (2.03 GB/1.89 GiB)
sd 5:0:0:0: [sdg] Write Protect is off
sd 5:0:0:0: [sdg] Mode Sense: 43 00 00 00
sd 5:0:0:0: [sdg] Assuming drive cache: write through
PM: Adding info for No Bus:sdg
sd 5:0:0:0: [sdg] Assuming drive cache: write through
sdg: sdg1
PM: Adding info for No Bus:sdg1
PM: Adding info for No Bus:8:96
sd 5:0:0:0: [sdg] Assuming drive cache: write through
sd 5:0:0:0: [sdg] Attached SCSI removable disk
ata3.00: qc timeout (cmd 0xa0)
ata3.00: TEST_UNIT_READY failed (err_mask=0x5)
ata3: limiting SATA link speed to 1.5 Gbps
ata3.00: limiting speed to UDMA/100:PIO3
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.00: configured for UDMA/100
ata3.00: qc timeout (cmd 0xa0)
ata3.00: TEST_UNIT_READY failed (err_mask=0x5)
ata3.00: disabled
ata3: hard resetting link
ata3: nv: skipping hardreset on occupied port
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3: EH complete
ata4: SATA link down (SStatus 0 SControl 300)
usb 2-2:1.0: uevent
usb 2-2: uevent
usb 2-6.1.2.1:1.0: uevent
usb 2-6.1.2.1: uevent
usb 2-2:1.0: uevent
usb 2-2: uevent
usb 2-2:1.0: uevent
usb 2-2: uevent
usb 2-2:1.0: uevent
usb 2-2: uevent
usb 2-2:1.0: uevent
usb 2-6.1.2.1:1.0: uevent
usb 2-2:1.0: uevent
usb 2-2:1.0: uevent
usb 2-2:1.0: uevent
ide-cd driver 5.00
PM: Adding info for No Bus:0.0
ide-cd: hda: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2000kB Cache
Uniform CD-ROM driver Revision: 3.20
usb 2-6.1.2.1:1.0: uevent
usb 2-6.1.2.1: uevent
usb 2-6.1.2.1:1.0: uevent
PM: Adding info for No Bus:device-mapper
device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
PM: Adding info for No Bus:dm-0
PM: Adding info for No Bus:254:0
PM: Adding info for No Bus:dm-1
PM: Adding info for No Bus:254:1
PM: Adding info for No Bus:dm-2
PM: Adding info for No Bus:254:2
PM: Adding info for No Bus:dm-3
PM: Adding info for No Bus:254:3
PM: Adding info for No Bus:dm-4
PM: Adding info for No Bus:254:4
PM: Adding info for No Bus:dm-5
PM: Adding info for No Bus:254:5
PM: Adding info for No Bus:hda
PM: Adding info for No Bus:3:0
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
xor: automatically using best checksumming function: pIII_sse
pIII_sse : 7516.000 MB/sec
xor: using function: pIII_sse (7516.000 MB/sec)
raid6: int32x1 878 MB/s
raid6: int32x2 839 MB/s
raid6: int32x4 703 MB/s
raid6: int32x8 585 MB/s
raid6: mmxx1 2742 MB/s
raid6: mmxx2 3167 MB/s
raid6: sse1x1 1890 MB/s
raid6: sse1x2 2441 MB/s
raid6: sse2x1 3546 MB/s
raid6: sse2x2 4222 MB/s
raid6: using algorithm sse2x2 (4222 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
md: raid10 personality registered for level 10
PM: Marking nosave pages: 000000000009c000 - 0000000000100000
PM: Basic memory bitmaps created
PM: Basic memory bitmaps freed
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with writeback data mode.
udev: starting version 146
usb usb1: uevent
usb 1-0:1.0: uevent
usb usb2: uevent
usb 2-0:1.0: uevent
usb 2-2: uevent
usb 2-2:1.0: uevent
usb 2-3: uevent
usb 2-3.3: uevent
usb 2-3.3.1: uevent
usb 2-3.3.1:1.0: uevent
usb 2-3.3.3: uevent
usb 2-3.3.3:1.0: uevent
usb 2-3.3.3:1.1: uevent
usb 2-3.3:1.0: uevent
usb 2-3:1.0: uevent
usb 2-6: uevent
usb 2-6.1: uevent
usb 2-6.1.1: uevent
usb 2-6.1.1:1.0: uevent
usb 2-6.1.1:1.1: uevent
usb 2-6.1.2: uevent
usb 2-6.1.2.1: uevent
usb 2-6.1.2.1:1.0: uevent
usb 2-6.1.2.2: uevent
usb 2-6.1.2.2:1.0: uevent
usb 2-6.1.2:1.0: uevent
usb 2-6.1:1.0: uevent
usb 2-6:1.0: uevent
usb usb1: uevent
usb usb2: uevent
usb usb1: uevent
usb usb2: uevent
usb 2-6: uevent
usb 2-2: uevent
usb 2-3: uevent
usb 2-6: uevent
usb 2-2:1.0: uevent
usb 2-2: uevent
usb 2-2:1.0: uevent
usb 2-2: uevent
usb 2-2:1.0: uevent
usb 2-2: uevent
usb 2-2:1.0: uevent
usb 2-2: uevent
usb 2-2: uevent
usb 2-2:1.0: uevent
usb 2-2:1.0: uevent
usb 2-2:1.0: uevent
usb 2-3: uevent
PM: Adding info for No Bus:input6
input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input6
ACPI: Power Button [PWRB]
PM: Adding info for No Bus:input7
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input7
ACPI: Power Button [PWRF]
usb 2-6.1: uevent
usb 2-2:1.0: uevent
usb 2-6.1: uevent
usb 2-3.3: uevent
usb 2-3.3: uevent
usb 2-6.1.2: uevent
usb 2-3.3.1: uevent
PM: Adding info for No Bus:rtc
Real Time Clock Driver v1.12b
usb 2-6.1.2: uevent
usb 2-3.3.1: uevent
usb 2-6.1.1: uevent
usb 2-3.3.3: uevent
usb 2-6.1.2.2: uevent
usb 2-6.1.1: uevent
usb 2-3.3.3: uevent
usb 2-6.1.2.2: uevent
usb 2-6.1.2.1: uevent
usb 2-6.1.2.1:1.0: uevent
usb 2-6.1.2.1: uevent
usb 2-6.1.2.1:1.0: uevent
usb 2-6.1.2.1: uevent
ACPI: SSDT 7fefa940 00175 (v01 Nvidia ASUSACPI 42302E31 AWRD 00000000)
PM: Adding info for No Bus:cooling_device1
processor LNXCPU:00: registered as cooling_device1
ACPI: SSDT 7fefad50 000CE (v01 Nvidia ASUSACPI 42302E31 AWRD 00000000)
PM: Adding info for No Bus:cooling_device2
processor LNXCPU:01: registered as cooling_device2
PM: Adding info for No Bus:raw1394
ieee1394: raw1394: /dev/raw1394 device initialized
PM: Adding info for No Bus:hwmon0
PM: Adding info for No Bus:event0
PM: Adding info for No Bus:event1
PM: Adding info for No Bus:event2
PM: Adding info for No Bus:event3
PM: Adding info for No Bus:event4
PM: Adding info for No Bus:event5
PM: Adding info for No Bus:event6
PM: Adding info for No Bus:event7
usb 2-3.3.3:1.0: uevent
usb 2-3.3.3: uevent
usb 2-6.1.2.2:1.0: uevent
usb 2-6.1.2.2: uevent
usb 2-6.1.1:1.0: uevent
usb 2-6.1.1: uevent
usb 2-3.3.3:1.1: uevent
usb 2-3.3.3: uevent
usb 2-6.1.2.2:1.0: uevent
usb 2-6.1.2.2: uevent
usb 2-3.3.3:1.1: uevent
usb 2-3.3.3: uevent
usb 2-3.3.3:1.0: uevent
usb 2-6.1.2.2:1.0: uevent
usb 2-6.1.1:1.0: uevent
usb 2-3.3.3:1.1: uevent
usb 2-3.3.3:1.1: uevent
usb 2-6.1.2.2:1.0: uevent
ACPI: I/O resource nForce2_smbus [0x5000-0x503f] conflicts with ACPI region SM00 [0x5000-0x5005]
ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
nForce2_smbus 0000:00:0a.1: Error probing SMB1.
PM: Adding info for i2c:i2c-0
i2c i2c-0: nForce2 SMBus adapter at 0x5100
usb 2-3.3.1:1.0: uevent
usb 2-3.3.1: uevent
usb 2-3.3.1:1.0: uevent
usb 2-3.3.1: uevent
usb 2-3.3.1:1.0: uevent
usb 2-3.3.1:1.0: uevent
PM: Adding info for No Bus:dv1394-0
usb 2-6.1.1:1.1: uevent
usb 2-6.1.1: uevent
usb 2-6.1.1:1.1: uevent
usb 2-6.1.1:1.1: uevent
usb 2-6.1.1: uevent
usb 2-6.1.1:1.1: uevent
PM: Adding info for No Bus:timer
PM: Adding info for No Bus:seq
hda: UDMA/66 mode selected
PM: Adding info for No Bus:sequencer
PM: Adding info for No Bus:sequencer2
ACPI: PCI Interrupt Link [AAZA] enabled at IRQ 23
HDA Intel 0000:00:10.1: PCI INT B -> Link[AAZA] -> GSI 23 (level, low) -> IRQ 23
HDA Intel 0000:00:10.1: setting latency timer to 64
PM: Adding info for No Bus:input8
input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:10.1/input/input8
PM: Adding info for No Bus:event8
PM: Adding info for No Bus:card0
PM: Adding info for No Bus:pcmC0D1p
PM: Adding info for No Bus:adsp
PM: Adding info for No Bus:pcmC0D0p
PM: Adding info for No Bus:pcmC0D0c
PM: Adding info for No Bus:dsp
PM: Adding info for No Bus:audio
PM: Adding info for No Bus:hwC0D0
PM: Adding info for No Bus:controlC0
PM: Adding info for No Bus:mixer
PM: Adding info for No Bus:vcs2
PM: Adding info for No Bus:vcsa2
PM: Adding info for No Bus:vcs3
PM: Adding info for No Bus:vcsa3
PM: Adding info for No Bus:vcs4
PM: Adding info for No Bus:vcsa4
PM: Adding info for No Bus:vcs5
PM: Adding info for No Bus:vcsa5
PM: Adding info for No Bus:vcs6
PM: Adding info for No Bus:vcsa6
hda: UDMA/66 mode selected
EXT3 FS on dm-1, internal journal
i2c /dev entries driver
PM: Adding info for No Bus:i2c-0
it87: Found IT8712F chip at 0x290, revision 7
it87: in3 is VCC (+5V)
it87: in7 is VCCH (+5V Stand-By)
ACPI: I/O resource it87 [0x295-0x296] conflicts with ACPI region HWRE [0x295-0x296]
ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
fuse init (API version 7.13)
PM: Adding info for No Bus:fuse
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-4, internal journal
EXT3-fs: mounted filesystem with writeback data mode.
PM: Adding info for No Bus:254:2-fuseblk
PM: Adding info for No Bus:254:5-fuseblk
Adding 4194296k swap on /mnt/oldlin/4G-memory.swap. Priority:-1 extents:1057 across:4264956k
r8169: eth1: link up
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PM: Adding info for No Bus:0:16
PM: Adding info for No Bus:0:17
PM: Adding info for No Bus:0:18
PM: Adding info for No Bus:vcs10
PM: Adding info for No Bus:vcsa10
usb 2-3.3.1: link qh8-0e01/f739a940 start 2 [1/2 us]
usb 2-6.1.2.2: link qh8-0e01/f739a900 start 3 [1/2 us]
usb 2-3.3.1: unlink qh8-0e01/f739a940 start 2 [1/2 us]
usb 2-6.1.2.2: unlink qh8-0e01/f739a900 start 3 [1/2 us]
ehci_hcd 0000:00:0b.1: reused qh f739a940 schedule
usb 2-3.3.1: link qh8-0e01/f739a940 start 2 [1/2 us]
ehci_hcd 0000:00:0b.1: reused qh f739a900 schedule
usb 2-6.1.2.2: link qh8-0e01/f739a900 start 3 [1/2 us]
irda_init()
NET: Registered protocol family 23
usbcore: registered new interface driver stir4200
usb 2-2:1.0: uevent
usb 2-2: uevent
usb 2-2:1.0: uevent
usb 2-2:1.0: uevent
usb 2-2: uevent
usb 2-2:1.0: uevent
usb 2-2:1.0: uevent
usb 2-2: uevent
usb 2-2:1.0: uevent
usb 2-2:1.0: uevent
usb 2-2: uevent
usb 2-6.1.2.1:1.0: uevent
usb 2-6.1.2.1: uevent
usb 2-2:1.0: uevent
usb 2-6.1.2.1:1.0: uevent
warning: `ntpd' uses 32-bit capabilities (legacy support in use)
usb usb1: uevent
usb 1-0:1.0: uevent
usb usb2: uevent
usb 2-0:1.0: uevent
usb 2-2: uevent
usb 2-2:1.0: uevent
usb 2-3: uevent
usb 2-3.3: uevent
usb 2-3.3.1: uevent
usb 2-3.3.1:1.0: uevent
usb 2-3.3.3: uevent
usb 2-3.3.3:1.0: uevent
usb 2-3.3.3:1.1: uevent
usb 2-3.3:1.0: uevent
usb 2-3:1.0: uevent
usb 2-6: uevent
usb 2-6.1: uevent
usb 2-6.1.1: uevent
usb 2-6.1.1:1.0: uevent
usb 2-6.1.1:1.1: uevent
usb 2-6.1.2: uevent
usb 2-6.1.2.1: uevent
usb 2-6.1.2.1:1.0: uevent
usb 2-6.1.2.2: uevent
usb 2-6.1.2.2:1.0: uevent
usb 2-6.1.2:1.0: uevent
usb 2-6.1:1.0: uevent
usb 2-6:1.0: uevent
Bluetooth: Core ver 2.15
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.14
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM ver 1.11
Bluetooth: SCO (Voice Link) ver 0.6
Bluetooth: SCO socket layer initialized
CPUFREQ: Per core ondemand sysfs interface is deprecated - up_threshold
CPUFREQ: Per core ondemand sysfs interface is deprecated - ignore_nice_load
PM: Adding info for No Bus:vcs7
PM: Adding info for No Bus:vcsa7
Linux agpgart interface v0.103
nvidia: module license 'NVIDIA' taints kernel.
Disabling lock debugging due to kernel taint
ACPI: PCI Interrupt Link [APC5] enabled at IRQ 16
nvidia 0000:01:00.0: PCI INT A -> Link[APC5] -> GSI 16 (level, low) -> IRQ 16
nvidia 0000:01:00.0: setting latency timer to 64
NVRM: loading NVIDIA UNIX x86 Kernel Module 185.18.36 Fri Aug 14 17:18:04 PDT 2009
PM: Adding info for i2c:i2c-1
PM: Adding info for No Bus:i2c-1
PM: Adding info for i2c:i2c-2
PM: Adding info for No Bus:i2c-2
PM: Adding info for i2c:i2c-3
PM: Adding info for No Bus:i2c-3
hda: command error: status=0x51 { DriveReady SeekComplete Error }
hda: command error: error=0x50 { LastFailedSense=0x05 }
hda: possibly failed opcode: 0xa0
end_request: I/O error, dev hda, sector 768856
Buffer I/O error on device hda, logical block 96107
hda: command error: status=0x51 { DriveReady SeekComplete Error }
hda: command error: error=0x50 { LastFailedSense=0x05 }
hda: possibly failed opcode: 0xa0
end_request: I/O error, dev hda, sector 768856
Buffer I/O error on device hda, logical block 96107
hda: command error: status=0x51 { DriveReady SeekComplete Error }
hda: command error: error=0x50 { LastFailedSense=0x05 }
hda: possibly failed opcode: 0xa0
end_request: I/O error, dev hda, sector 768856
Buffer I/O error on device hda, logical block 96107
hda: command error: status=0x51 { DriveReady SeekComplete Error }
hda: command error: error=0x50 { LastFailedSense=0x05 }
hda: possibly failed opcode: 0xa0
end_request: I/O error, dev hda, sector 768856
Buffer I/O error on device hda, logical block 96107
usb usb1: uevent
usb 1-0:1.0: uevent
usb usb2: uevent
usb 2-0:1.0: uevent
usb 2-2: uevent
usb 2-2:1.0: uevent
usb 2-3: uevent
usb 2-3:1.0: uevent
usb 2-6: uevent
usb 2-6:1.0: uevent
usb 2-3.3: uevent
usb 2-3.3:1.0: uevent
usb 2-6.1: uevent
usb 2-6.1:1.0: uevent
usb 2-3.3.3: uevent
usb 2-3.3.3:1.0: uevent
usb 2-3.3.3:1.1: uevent
usb 2-6.1.1: uevent
usb 2-6.1.1:1.0: uevent
usb 2-6.1.1:1.1: uevent
usb 2-6.1.2: uevent
usb 2-6.1.2:1.0: uevent
usb 2-3.3.1: uevent
usb 2-3.3.1:1.0: uevent
usb 2-6.1.2.1: uevent
usb 2-6.1.2.1:1.0: uevent
usb 2-6.1.2.2: uevent
usb 2-6.1.2.2:1.0: uevent
usb usb1: uevent
usb 1-0:1.0: uevent
usb usb2: uevent
usb 2-0:1.0: uevent
usb 2-2: uevent
usb 2-2:1.0: uevent
usb 2-3: uevent
usb 2-3.3: uevent
usb 2-3.3.1: uevent
usb 2-3.3.1:1.0: uevent
usb 2-3.3.3: uevent
usb 2-3.3.3:1.0: uevent
usb 2-3.3.3:1.1: uevent
usb 2-3.3:1.0: uevent
usb 2-3:1.0: uevent
usb 2-6: uevent
usb 2-6.1: uevent
usb 2-6.1.1: uevent
usb 2-6.1.1:1.0: uevent
usb 2-6.1.1:1.1: uevent
usb 2-6.1.2: uevent
usb 2-6.1.2.1: uevent
usb 2-6.1.2.1:1.0: uevent
usb 2-6.1.2.2: uevent
usb 2-6.1.2.2:1.0: uevent
usb 2-6.1.2:1.0: uevent
usb 2-6.1:1.0: uevent
usb 2-6:1.0: uevent
CPU0 attaching NULL sched-domain.
CPU1 attaching NULL sched-domain.
CPU0 attaching sched-domain:
domain 0: span 0-1 level MC
groups: 0 1
CPU1 attaching sched-domain:
domain 0: span 0-1 level MC
groups: 1 0
usb usb1: uevent
usb 1-0:1.0: uevent
usb usb2: uevent
usb 2-0:1.0: uevent
usb 2-2: uevent
usb 2-2:1.0: uevent
usb 2-3: uevent
usb 2-3.3: uevent
usb 2-3.3.1: uevent
usb 2-3.3.1:1.0: uevent
usb 2-3.3.3: uevent
usb 2-3.3.3:1.0: uevent
usb 2-3.3.3:1.1: uevent
usb 2-3.3:1.0: uevent
usb 2-3:1.0: uevent
usb 2-6: uevent
usb 2-6.1: uevent
usb 2-6.1.1: uevent
usb 2-6.1.1:1.0: uevent
usb 2-6.1.1:1.1: uevent
usb 2-6.1.2: uevent
usb 2-6.1.2.1: uevent
usb 2-6.1.2.1:1.0: uevent
usb 2-6.1.2.2: uevent
usb 2-6.1.2.2:1.0: uevent
usb 2-6.1.2:1.0: uevent
usb 2-6.1:1.0: uevent
usb 2-6:1.0: uevent
ISO 9660 Extensions: Microsoft Joliet Level 3
ISOFS: changing to secondary root
r8169: eth1: link up
ehci_hcd 0000:00:0b.1: detected XactErr len 0/31 retry 1
ieee1394: Node paused: ID:BUS[0-01:1023] GUID[001a66fffee31809]
ieee1394: Node reactivated: ID:BUS[0-01:1023] GUID[001a66fffee31809]
[-- Attachment #3: Type: TEXT/PLAIN, Size: 28878 bytes --]
salon
description: Desktop Computer
product: System Product Name
vendor: System manufacturer
version: System Version
serial: System Serial Number
width: 32 bits
capabilities: smbios-2.4 dmi-2.4 smp-1.4 smp
configuration: boot=normal chassis=desktop cpus=2 uuid=D8F42417-5326-DB11-B746-517A9EEA8F7C
*-core
description: Motherboard
product: P5NSLI
vendor: ASUSTeK Computer INC.
physical id: 0
version: 1.XX
serial: 123456789000
*-firmware
description: BIOS
vendor: Phoenix Technologies, LTD
physical id: 0
version: ASUS P5NSLI ACPI BIOS Revision 1801 (11/18/2008)
size: 128KiB
capacity: 448KiB
capabilities: pci pnp apm upgrade shadowing cdboot bootselect socketedrom edd int13floppy360 int13floppy1200 int13floppy720 int13floppy2880 int5printscreen int9keyboard int14serial int17printer int10video acpi usb ls120boot zipboot biosbootspecification
*-cpu:0
description: CPU
product: Intel(R) Core(TM)2 CPU 6400 @ 2.13GHz
vendor: Intel Corp.
physical id: 4
bus info: cpu@0
version: 6.15.6
serial: 0000-06F6-0000-0000-0000-0000
slot: Socket 775
size: 2133MHz
capacity: 3800MHz
width: 64 bits
clock: 266MHz
capabilities: boot fpu fpu_exception wp vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe nx x86-64 constant_tsc arch_perfmon pebs bts aperfmperf pni dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm lahf_lm tpr_shadow cpufreq
configuration: id=0
*-cache:0
description: L1 cache
physical id: a
slot: L1 Cache
size: 32KiB
capacity: 32KiB
capabilities: synchronous internal write-back data
*-cache:1
description: L2 cache
physical id: b
slot: L2 Cache
size: 2MiB
capacity: 2MiB
capabilities: synchronous internal write-back unified
*-logicalcpu:0
description: Logical CPU
physical id: 0.1
width: 64 bits
capabilities: logical
*-logicalcpu:1
description: Logical CPU
physical id: 0.2
width: 64 bits
capabilities: logical
*-memory
description: System Memory
physical id: 34
slot: System board or motherboard
size: 2GiB
*-bank:0
description: DIMM DDR2 667 MHz (1.5 ns)
product: None
vendor: None
physical id: 0
serial: None
slot: DIMM_A1
size: 1GiB
clock: 667MHz (1.5ns)
*-bank:1
description: DIMM [empty]
product: None
vendor: None
physical id: 1
serial: None
slot: DIMM_A2
*-bank:2
description: DIMM DDR2 667 MHz (1.5 ns)
product: None
vendor: None
physical id: 2
serial: None
slot: DIMM_B1
size: 1GiB
clock: 667MHz (1.5ns)
*-bank:3
description: DIMM [empty]
product: None
vendor: None
physical id: 3
serial: None
slot: DIMM_B2
*-cpu:1
physical id: 1
bus info: cpu@1
version: 6.15.6
serial: 0000-06F6-0000-0000-0000-0000
size: 2133MHz
capacity: 2133MHz
capabilities: vmx ht cpufreq
configuration: id=0
*-logicalcpu:0
description: Logical CPU
physical id: 0.1
capabilities: logical
*-logicalcpu:1
description: Logical CPU
physical id: 0.2
capabilities: logical
*-pci
description: Host bridge
product: nVidia Corporation
vendor: nVidia Corporation
physical id: 100
bus info: pci@0000:00:00.0
version: a3
width: 32 bits
clock: 66MHz
*-memory:0 UNCLAIMED
description: RAM memory
product: nVidia Corporation
vendor: nVidia Corporation
physical id: 0.1
bus info: pci@0000:00:00.1
version: a1
width: 32 bits
clock: 66MHz (15.2ns)
configuration: latency=0
*-memory:1 UNCLAIMED
description: RAM memory
product: nVidia Corporation
vendor: nVidia Corporation
physical id: 0.2
bus info: pci@0000:00:00.2
version: a1
width: 32 bits
clock: 66MHz (15.2ns)
configuration: latency=0
*-memory:2 UNCLAIMED
description: RAM memory
product: nVidia Corporation
vendor: nVidia Corporation
physical id: 0.3
bus info: pci@0000:00:00.3
version: a1
width: 32 bits
clock: 66MHz (15.2ns)
configuration: latency=0
*-memory:3 UNCLAIMED
description: RAM memory
product: nVidia Corporation
vendor: nVidia Corporation
physical id: 0.4
bus info: pci@0000:00:00.4
version: a1
width: 32 bits
clock: 66MHz (15.2ns)
capabilities: bus_master
configuration: latency=0
*-memory:4 UNCLAIMED
description: RAM memory
product: nVidia Corporation
vendor: nVidia Corporation
physical id: 1
bus info: pci@0000:00:01.0
version: a1
width: 32 bits
clock: 66MHz (15.2ns)
configuration: latency=0
*-memory:5 UNCLAIMED
description: RAM memory
product: nVidia Corporation
vendor: nVidia Corporation
physical id: 1.1
bus info: pci@0000:00:01.1
version: a1
width: 32 bits
clock: 66MHz (15.2ns)
configuration: latency=0
*-memory:6 UNCLAIMED
description: RAM memory
product: nVidia Corporation
vendor: nVidia Corporation
physical id: 1.2
bus info: pci@0000:00:01.2
version: a1
width: 32 bits
clock: 66MHz (15.2ns)
configuration: latency=0
*-memory:7 UNCLAIMED
description: RAM memory
product: nVidia Corporation
vendor: nVidia Corporation
physical id: 1.3
bus info: pci@0000:00:01.3
version: a1
width: 32 bits
clock: 66MHz (15.2ns)
configuration: latency=0
*-memory:8 UNCLAIMED
description: RAM memory
product: nVidia Corporation
vendor: nVidia Corporation
physical id: 1.4
bus info: pci@0000:00:01.4
version: a1
width: 32 bits
clock: 66MHz (15.2ns)
configuration: latency=0
*-memory:9 UNCLAIMED
description: RAM memory
product: nVidia Corporation
vendor: nVidia Corporation
physical id: 1.5
bus info: pci@0000:00:01.5
version: a1
width: 32 bits
clock: 66MHz (15.2ns)
configuration: latency=0
*-memory:10 UNCLAIMED
description: RAM memory
product: nVidia Corporation
vendor: nVidia Corporation
physical id: 1.6
bus info: pci@0000:00:01.6
version: a1
width: 32 bits
clock: 66MHz (15.2ns)
configuration: latency=0
*-pci:0
description: PCI bridge
product: nVidia Corporation
vendor: nVidia Corporation
physical id: 2
bus info: pci@0000:00:02.0
version: a2
width: 32 bits
clock: 33MHz
capabilities: pci pm msi pciexpress normal_decode bus_master cap_list
configuration: driver=pcieport
resources: irq:0 ioport:a000(size=4096) memory:d0000000-d2ffffff ioport:c0000000(size=268435456)
*-display
description: VGA compatible controller
product: G71 [GeForce 7900 GT/GTO]
vendor: nVidia Corporation
physical id: 0
bus info: pci@0000:01:00.0
version: a1
width: 64 bits
clock: 33MHz
capabilities: pm msi pciexpress vga_controller bus_master cap_list rom
configuration: driver=nvidia latency=0
resources: irq:16 memory:d0000000-d0ffffff memory:c0000000-cfffffff(prefetchable) memory:d1000000-d1ffffff ioport:a000(size=128) memory:d2000000-d201ffff(prefetchable)
*-pci:1
description: PCI bridge
product: nVidia Corporation
vendor: nVidia Corporation
physical id: 4
bus info: pci@0000:00:04.0
version: a2
width: 32 bits
clock: 33MHz
capabilities: pci pm msi pciexpress normal_decode bus_master cap_list
configuration: driver=pcieport
resources: irq:0
*-pci:2
description: PCI bridge
product: nVidia Corporation
vendor: nVidia Corporation
physical id: 5
bus info: pci@0000:00:05.0
version: a2
width: 32 bits
clock: 33MHz
capabilities: pci pm msi pciexpress normal_decode bus_master cap_list
configuration: driver=pcieport
resources: irq:0
*-pci:3
description: PCI bridge
product: nVidia Corporation
vendor: nVidia Corporation
physical id: 6
bus info: pci@0000:00:06.0
version: a2
width: 32 bits
clock: 33MHz
capabilities: pci pm msi pciexpress normal_decode bus_master cap_list
configuration: driver=pcieport
resources: irq:0
*-pci:4
description: PCI bridge
product: nVidia Corporation
vendor: nVidia Corporation
physical id: 7
bus info: pci@0000:00:07.0
version: a2
width: 32 bits
clock: 33MHz
capabilities: pci pm msi pciexpress normal_decode bus_master cap_list
configuration: driver=pcieport
resources: irq:0
*-memory:11 UNCLAIMED
description: RAM memory
product: MCP51 Host Bridge
vendor: nVidia Corporation
physical id: 9
bus info: pci@0000:00:09.0
version: a2
width: 32 bits
clock: 66MHz (15.2ns)
capabilities: ht bus_master cap_list
configuration: latency=0
*-isa
description: ISA bridge
product: MCP51 LPC Bridge
vendor: nVidia Corporation
physical id: a
bus info: pci@0000:00:0a.0
version: a2
width: 32 bits
clock: 66MHz
capabilities: isa bus_master
configuration: latency=0
*-serial
description: SMBus
product: MCP51 SMBus
vendor: nVidia Corporation
physical id: a.1
bus info: pci@0000:00:0a.1
version: a2
width: 32 bits
clock: 66MHz
capabilities: pm cap_list
configuration: driver=nForce2_smbus latency=0
resources: irq:11 ioport:5000(size=64) ioport:5100(size=64)
*-memory:12 UNCLAIMED
description: RAM memory
product: MCP51 Memory Controller 0
vendor: nVidia Corporation
physical id: a.2
bus info: pci@0000:00:0a.2
version: a2
width: 32 bits
clock: 66MHz (15.2ns)
configuration: latency=0
*-usb:0
description: USB Controller
product: MCP51 USB Controller
vendor: nVidia Corporation
physical id: b
bus info: pci@0000:00:0b.0
version: a2
width: 32 bits
clock: 66MHz
capabilities: pm ohci bus_master cap_list
configuration: driver=ohci_hcd latency=0 maxlatency=1 mingnt=3
resources: irq:23 memory:d5006000-d5006fff
*-usbhost
product: OHCI Host Controller
vendor: Linux 2.6.32 ohci_hcd
physical id: 1
bus info: usb@1
logical name: usb1
version: 2.06
capabilities: usb-1.10
configuration: driver=hub slots=8 speed=12.0MB/s
*-usb:1
description: USB Controller
product: MCP51 USB Controller
vendor: nVidia Corporation
physical id: b.1
bus info: pci@0000:00:0b.1
version: a2
width: 32 bits
clock: 66MHz
capabilities: debug pm ehci bus_master cap_list
configuration: driver=ehci_hcd latency=0 maxlatency=1 mingnt=3
resources: irq:22 memory:d5007000-d50070ff
*-usbhost
product: EHCI Host Controller
vendor: Linux 2.6.32 ehci_hcd
physical id: 1
bus info: usb@2
logical name: usb2
version: 2.06
capabilities: usb-2.00
configuration: driver=hub slots=8 speed=480.0MB/s
*-usb:0
description: Mass storage device
product: Mass Storage Device
vendor: Generic
physical id: 2
bus info: usb@2:2
logical name: scsi0
version: 1.26
serial: 058F312D81B
capabilities: usb-2.00 scsi emulated scsi-host
configuration: driver=usb-storage maxpower=100mA speed=480.0MB/s
*-disk:0
description: SCSI Disk
physical id: 0.0.0
bus info: scsi@0:0.0.0
logical name: /dev/sdc
*-disk:1
description: SCSI Disk
physical id: 0.0.1
bus info: scsi@0:0.0.1
logical name: /dev/sdd
*-disk:2
description: SCSI Disk
physical id: 0.0.2
bus info: scsi@0:0.0.2
logical name: /dev/sde
*-disk:3
description: SCSI Disk
physical id: 0.0.3
bus info: scsi@0:0.0.3
logical name: /dev/sdf
*-usb:1
description: USB hub
product: HighSpeed Hub
vendor: NEC Corp.
physical id: 3
bus info: usb@2:3
version: 1.00
capabilities: usb-2.00
configuration: driver=hub maxpower=100mA slots=4 speed=480.0MB/s
*-usb
description: USB hub
product: USB Hub
vendor: Genesys Logic, Inc.
physical id: 3
bus info: usb@2:3.3
version: 3.05
capabilities: usb-1.10
configuration: driver=hub maxpower=100mA slots=4 speed=12.0MB/s
*-usb:0
description: Mouse
product: Macally ECOMouse
vendor: Macally Peripherals
physical id: 1
bus info: usb@2:3.3.1
version: 51.04
capabilities: usb-1.10
configuration: driver=usbhid maxpower=100mA speed=1.5MB/s
*-usb:1
description: Keyboard
product: Macally iKeySlim
vendor: Macally Peripherals
physical id: 3
bus info: usb@2:3.3.3
version: 1.01
capabilities: usb-1.10
configuration: driver=usbhid maxpower=100mA speed=1.5MB/s
*-usb:2
description: USB hub
product: USB2.0 Hub
vendor: Genesys Logic, Inc.
physical id: 6
bus info: usb@2:6
version: 6.0b
capabilities: usb-2.00
configuration: driver=hub maxpower=100mA slots=4 speed=480.0MB/s
*-usb
description: USB hub
product: HighSpeed Hub
vendor: NEC Corp.
physical id: 1
bus info: usb@2:6.1
version: 1.00
capabilities: usb-2.00
configuration: driver=hub maxpower=100mA slots=4 speed=480.0MB/s
*-usb:0
description: Keyboard
product: PS2 to USB AdapterA3
vendor: Uni Class Technology Co., Ltd
physical id: 1
bus info: usb@2:6.1.1
version: 0.01
capabilities: usb-1.10
configuration: driver=usbhid maxpower=98mA speed=1.5MB/s
*-usb:1
description: USB hub
product: USB2.0 Hub
vendor: Genesys Logic, Inc.
physical id: 2
bus info: usb@2:6.1.2
version: 6.0b
capabilities: usb-2.00
configuration: driver=hub maxpower=100mA slots=4 speed=480.0MB/s
*-usb:0
description: Mass storage device
product: DISK 2.0
vendor: USB
physical id: 1
bus info: usb@2:6.1.2.1
logical name: scsi5
version: 4.03
serial: PHN84K6AD8PLXSVC
capabilities: usb-2.00 scsi emulated scsi-host
configuration: driver=usb-storage maxpower=100mA speed=480.0MB/s
*-disk
description: SCSI Disk
physical id: 0.0.0
bus info: scsi@5:0.0.0
logical name: /dev/sdg
size: 1944MiB (2038MB)
capabilities: gpt-1.00 partitioned partitioned:gpt
configuration: guid=44a4b1dc-a2a3-4289-993a-f99b28f82c34
*-volume:0 UNCLAIMED
description: EFI partition
physical id: 1
bus info: scsi@5:0.0.0,1
serial: 39a6a1b7-06c1-4e87-97aa-6233c448cae8
capacity: 95MiB
configuration: name=primary
*-volume:1 UNCLAIMED
description: Windows reserved partition
physical id: 2
bus info: scsi@5:0.0.0,2
serial: 2c9a9f6c-f9ff-45db-8808-7da0d594cf25
capacity: 1848MiB
capabilities: nofs
*-usb:1
description: Mouse
product: USB Optical Mouse
vendor: Logitech
physical id: 2
bus info: usb@2:6.1.2.2
version: 21.10
capabilities: usb-1.10
configuration: driver=usbhid maxpower=100mA speed=1.5MB/s
*-ide:0
description: IDE interface
product: MCP51 IDE
vendor: nVidia Corporation
physical id: d
bus info: pci@0000:00:0d.0
version: a1
width: 32 bits
clock: 66MHz
capabilities: ide pm bus_master cap_list
configuration: driver=AMD_IDE latency=0 maxlatency=1 mingnt=3
resources: irq:0 ioport:1f0(size=8) ioport:3f6 ioport:170(size=8) ioport:376 ioport:f000(size=16)
*-ide
description: IDE Channel 1
physical id: 0
bus info: ide@0
logical name: ide0
clock: 66MHz
*-cdrom
description: DVD writer
product: PIONEER DVD-RW DVR-111D
vendor: Pioneer
physical id: 0
bus info: ide@0.0
logical name: /dev/hda
logical name: /media/Indigo CD1
version: 1.23
capabilities: packet atapi cdrom removable nonmagnetic dma lba iordy pm audio cd-r cd-rw dvd dvd-r
configuration: mode=udma4 mount.fstype=iso9660 mount.options=ro,nosuid,nodev,relatime,uid=501 state=mounted status=ready
*-medium
physical id: 0
logical name: /dev/hda
logical name: /media/Indigo CD1
configuration: mount.fstype=iso9660 mount.options=ro,nosuid,nodev,relatime,uid=501 state=mounted
*-storage
description: RAID bus controller
product: MCP51 Serial ATA Controller
vendor: nVidia Corporation
physical id: e
bus info: pci@0000:00:0e.0
logical name: scsi1
logical name: scsi2
version: a1
width: 32 bits
clock: 66MHz
capabilities: storage pm msi ht bus_master cap_list emulated
configuration: driver=sata_nv latency=0 maxlatency=1 mingnt=3
resources: irq:21 ioport:9f0(size=8) ioport:bf0(size=4) ioport:970(size=8) ioport:b70(size=4) ioport:d400(size=16) memory:d5004000-d5004fff
*-disk:0
description: ATA Disk
product: SAMSUNG SP2504C
physical id: 0
bus info: scsi@1:0.0.0
logical name: /dev/sda
version: VT10
serial: S09QJ1NL410815
size: 232GiB (250GB)
capabilities: partitioned partitioned:dos
configuration: ansiversion=5 signature=9df59df5
*-volume:0
description: EXT3 volume
vendor: Linux
physical id: 1
bus info: scsi@1:0.0.0,1
logical name: /dev/sda1
version: 1.0
serial: 9370b0bb-092a-4a6f-b68d-c5f7b87390ef
size: 13GiB
capacity: 13GiB
capabilities: primary journaled recover ext3 ext2 initialized
configuration: created=2006-09-11 10:48:14 filesystem=ext3 modified=2009-12-20 20:10:31 mounted=2009-12-22 04:29:12 state=clean
*-volume:1
description: HPFS/NTFS partition
physical id: 2
bus info: scsi@1:0.0.0,2
logical name: /dev/sda2
capacity: 112GiB
capabilities: primary bootable
*-disk:1
description: ATA Disk
product: ST3250620AS
vendor: Seagate
physical id: 1
bus info: scsi@2:0.0.0
logical name: /dev/sdb
version: 3.AA
serial: 5QE0AXQ8
size: 232GiB (250GB)
configuration: ansiversion=5
*-ide:1
description: IDE interface
product: MCP51 Serial ATA Controller
vendor: nVidia Corporation
physical id: f
bus info: pci@0000:00:0f.0
version: a1
width: 32 bits
clock: 66MHz
capabilities: ide pm msi ht bus_master cap_list
configuration: driver=sata_nv latency=0 maxlatency=1 mingnt=3
resources: irq:20 ioport:9e0(size=8) ioport:be0(size=4) ioport:960(size=8) ioport:b60(size=4) ioport:e800(size=16) memory:d5005000-d5005fff
*-pci:5
description: PCI bridge
product: MCP51 PCI Bridge
vendor: nVidia Corporation
physical id: 10
bus info: pci@0000:00:10.0
version: a2
width: 32 bits
clock: 66MHz
capabilities: pci ht subtractive_decode bus_master cap_list
resources: ioport:b000(size=4096) memory:d3000000-d4ffffff memory:80000000-800fffff(prefetchable)
*-firewire
description: FireWire (IEEE 1394)
product: VT6306 Fire II IEEE 1394 OHCI Link Layer Controller
vendor: VIA Technologies, Inc.
physical id: 6
bus info: pci@0000:06:06.0
version: 46
width: 32 bits
clock: 33MHz
capabilities: pm ohci bus_master cap_list
configuration: driver=ohci1394 latency=32 maxlatency=32
resources: irq:16 memory:d4001000-d40017ff ioport:b000(size=128)
*-network
description: Ethernet interface
product: RTL-8169 Gigabit Ethernet
vendor: Realtek Semiconductor Co., Ltd.
physical id: 7
bus info: pci@0000:06:07.0
logical name: eth1
version: 10
serial: 00:14:d1:1a:ac:15
size: 1GB/s
capacity: 1GB/s
width: 32 bits
clock: 66MHz
capabilities: pm bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation
configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full ip=192.168.0.33 latency=64 link=yes maxlatency=64 mingnt=32 multicast=yes port=MII speed=1GB/s
resources: irq:17 ioport:b400(size=256) memory:d4000000-d40000ff memory:80000000-8001ffff(prefetchable)
*-multimedia
description: Audio device
product: MCP51 High Definition Audio
vendor: nVidia Corporation
physical id: 10.1
bus info: pci@0000:00:10.1
version: a2
width: 32 bits
clock: 66MHz
capabilities: pm msi ht bus_master cap_list
configuration: driver=HDA Intel latency=0 maxlatency=5 mingnt=2
resources: irq:23 memory:d5000000-d5003fff
[-- Attachment #4: Type: TEXT/PLAIN, Size: 28098 bytes --]
00:00.0 Host bridge: nVidia Corporation Device 0071 (rev a3)
Subsystem: ASUSTeK Computer Inc. Device 8189
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: [40] HyperTransport: Host or Secondary Interface
Command: WarmRst+ DblEnd-
Link Control: CFlE+ CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0
Link Config: MLWI=8bit MLWO=8bit LWI=8bit LWO=8bit
Revision ID: 0.16
00:00.1 RAM memory: nVidia Corporation Device 007f (rev a1)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:00.2 RAM memory: nVidia Corporation Device 0075 (rev a1)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:00.3 RAM memory: nVidia Corporation Device 006f (rev a1)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:00.4 RAM memory: nVidia Corporation Device 00b4 (rev a1)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:01.0 RAM memory: nVidia Corporation Device 0076 (rev a1)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:01.1 RAM memory: nVidia Corporation Device 0078 (rev a1)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:01.2 RAM memory: nVidia Corporation Device 0079 (rev a1)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:01.3 RAM memory: nVidia Corporation Device 007a (rev a1)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:01.4 RAM memory: nVidia Corporation Device 007b (rev a1)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:01.5 RAM memory: nVidia Corporation Device 007c (rev a1)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:01.6 RAM memory: nVidia Corporation Device 007d (rev a1)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:02.0 PCI bridge: nVidia Corporation Device 007e (rev a2) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000a000-0000afff
Memory behind bridge: d0000000-d2ffffff
Prefetchable memory behind bridge: 00000000c0000000-00000000cfffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [48] MSI: Enable- Count=1/2 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [80] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 <4us
ExtTag- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x16, ASPM L0s, Latency L0 <1us, L1 <4us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surpise-
Slot # 1, PowerLimit 0.000000; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet+ LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [100] Virtual Channel <?>
Kernel driver in use: pcieport
00:04.0 PCI bridge: nVidia Corporation Device 007e (rev a2) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [48] MSI: Enable- Count=1/2 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [80] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 <4us
ExtTag- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s, Latency L0 <1us, L1 <4us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x8, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surpise-
Slot # 2, PowerLimit 0.000000; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
Changed: MRL- PresDet- LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [100] Virtual Channel <?>
Kernel driver in use: pcieport
00:05.0 PCI bridge: nVidia Corporation Device 007e (rev a2) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [48] MSI: Enable- Count=1/2 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [80] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 <4us
ExtTag- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #2, Speed 2.5GT/s, Width x1, ASPM L0s, Latency L0 <1us, L1 <4us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surpise-
Slot # 4, PowerLimit 0.000000; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
Changed: MRL- PresDet- LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [100] Virtual Channel <?>
Kernel driver in use: pcieport
00:06.0 PCI bridge: nVidia Corporation Device 007e (rev a2) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [48] MSI: Enable- Count=1/2 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [80] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 <4us
ExtTag- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #3, Speed 2.5GT/s, Width x1, ASPM L0s, Latency L0 <1us, L1 <4us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surpise-
Slot # 8, PowerLimit 0.000000; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
Changed: MRL- PresDet- LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [100] Virtual Channel <?>
Kernel driver in use: pcieport
00:07.0 PCI bridge: nVidia Corporation Device 007e (rev a2) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [48] MSI: Enable- Count=1/2 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [80] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 <4us
ExtTag- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #4, Speed 2.5GT/s, Width x1, ASPM L0s, Latency L0 <1us, L1 <4us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surpise-
Slot # 10, PowerLimit 0.000000; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
Changed: MRL- PresDet- LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [100] Virtual Channel <?>
Kernel driver in use: pcieport
00:09.0 RAM memory: nVidia Corporation MCP51 Host Bridge (rev a2)
Subsystem: ASUSTeK Computer Inc. A8N-VM CSM Mainboard
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: [44] HyperTransport: Slave or Primary Interface
Command: BaseUnitID=9 UnitCnt=15 MastHost- DefDir- DUL-
Link Control 0: CFlE+ CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn+ LSEn+ ExtCTL- 64b-
Link Config 0: MLWI=8bit DwFcIn- MLWO=8bit DwFcOut- LWI=8bit DwFcInEn- LWO=8bit DwFcOutEn-
Link Control 1: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
Link Config 1: MLWI=8bit DwFcIn- MLWO=8bit DwFcOut- LWI=8bit DwFcInEn- LWO=8bit DwFcOutEn-
Revision ID: 1.03
Link Frequency 0: 800MHz
Link Error 0: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability 0: 200MHz+ 300MHz+ 400MHz+ 500MHz+ 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz- 1.4GHz- 1.6GHz- Vend-
Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA- UIDRD-
Link Frequency 1: 200MHz
Link Error 1: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability 1: 200MHz- 300MHz- 400MHz- 500MHz- 600MHz- 800MHz- 1.0GHz- 1.2GHz- 1.4GHz- 1.6GHz- Vend-
Error Handling: PFlE+ OFlE+ PFE- OFE- EOCFE- RFE- CRCFE- SERRFE- CF- RE- PNFE- ONFE- EOCNFE- RNFE- CRCNFE- SERRNFE-
Prefetchable memory behind bridge Upper: 00-00
Bus Number: 00
Capabilities: [e0] HyperTransport: MSI Mapping Enable- Fixed-
Mapping Address Base: 00000000fee00000
00:0a.0 ISA bridge: nVidia Corporation MCP51 LPC Bridge (rev a2)
Subsystem: ASUSTeK Computer Inc. A8N-VM CSM Mainboard
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:0a.1 SMBus: nVidia Corporation MCP51 SMBus (rev a2)
Subsystem: ASUSTeK Computer Inc. A8N-VM CSM Mainboard
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 11
Region 4: I/O ports at 5000 [size=64]
Region 5: I/O ports at 5100 [size=64]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: nForce2_smbus
Kernel modules: i2c-nforce2
00:0a.2 RAM memory: nVidia Corporation MCP51 Memory Controller 0 (rev a2)
Subsystem: ASUSTeK Computer Inc. Device 81bc
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:0b.0 USB Controller: nVidia Corporation MCP51 USB Controller (rev a2) (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. A8N-VM CSM Mainboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 23
Region 0: Memory at d5006000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: ohci_hcd
Kernel modules: ohci-hcd
00:0b.1 USB Controller: nVidia Corporation MCP51 USB Controller (rev a2) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. A8N-VM CSM Mainboard
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin B routed to IRQ 22
Region 0: Memory at d5007000 (32-bit, non-prefetchable) [size=256]
Capabilities: [44] Debug port: BAR=1 offset=0098
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:0d.0 IDE interface: nVidia Corporation MCP51 IDE (rev a1) (prog-if 8a [Master SecP PriP])
Subsystem: ASUSTeK Computer Inc. A8N-VM CSM Mainboard
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1]
Region 4: I/O ports at f000 [size=16]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: AMD_IDE
Kernel modules: pata_amd, amd74xx
00:0e.0 RAID bus controller: nVidia Corporation MCP51 Serial ATA Controller (rev a1) (prog-if 85)
Subsystem: ASUSTeK Computer Inc. A8N-VM CSM Mainboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 21
Region 0: I/O ports at 09f0 [size=8]
Region 1: I/O ports at 0bf0 [size=4]
Region 2: I/O ports at 0970 [size=8]
Region 3: I/O ports at 0b70 [size=4]
Region 4: I/O ports at d400 [size=16]
Region 5: Memory at d5004000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [b0] MSI: Enable- Count=1/4 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [cc] HyperTransport: MSI Mapping Enable- Fixed+
Kernel driver in use: sata_nv
Kernel modules: sata_nv
00:0f.0 IDE interface: nVidia Corporation MCP51 Serial ATA Controller (rev a1) (prog-if 85 [Master SecO PriO])
Subsystem: ASUSTeK Computer Inc. A8N-VM CSM Mainboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 20
Region 0: I/O ports at 09e0 [size=8]
Region 1: I/O ports at 0be0 [size=4]
Region 2: I/O ports at 0960 [size=8]
Region 3: I/O ports at 0b60 [size=4]
Region 4: I/O ports at e800 [size=16]
Region 5: Memory at d5005000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [b0] MSI: Enable- Count=1/4 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [cc] HyperTransport: MSI Mapping Enable- Fixed+
Kernel driver in use: sata_nv
Kernel modules: sata_nv
00:10.0 PCI bridge: nVidia Corporation MCP51 PCI Bridge (rev a2) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=06, subordinate=06, sec-latency=128
I/O behind bridge: 0000b000-0000bfff
Memory behind bridge: d3000000-d4ffffff
Prefetchable memory behind bridge: 80000000-800fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR+
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr+ DiscTmrStat+ DiscTmrSERREn-
Capabilities: [b8] Subsystem: Gammagraphx, Inc. (or missing ID) Device 0000
Capabilities: [8c] HyperTransport: MSI Mapping Enable- Fixed-
Mapping Address Base: 00000000fee00000
00:10.1 Audio device: nVidia Corporation MCP51 High Definition Audio (rev a2)
Subsystem: ASUSTeK Computer Inc. Device 818f
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (500ns min, 1250ns max)
Interrupt: pin B routed to IRQ 23
Region 0: Memory at d5000000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] MSI: Enable- Count=1/1 Maskable+ 64bit+
Address: 0000000000000000 Data: 0000
Masking: 00000000 Pending: 00000000
Capabilities: [6c] HyperTransport: MSI Mapping Enable- Fixed+
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel
01:00.0 VGA compatible controller: nVidia Corporation G71 [GeForce 7900 GT/GTO] (rev a1) (prog-if 00 [VGA controller])
Subsystem: eVga.com. Corp. Device c584
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at d0000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at c0000000 (64-bit, prefetchable) [size=256M]
Region 3: Memory at d1000000 (64-bit, non-prefetchable) [size=16M]
Region 5: I/O ports at a000 [size=128]
[virtual] Expansion ROM at d2000000 [disabled] [size=128K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [68] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [78] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <1us, L1 <4us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x16, ASPM L0s L1, Latency L0 <1us, L1 <4us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 128 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [100] Virtual Channel <?>
Capabilities: [128] Power Budgeting <?>
Kernel driver in use: nvidia
Kernel modules: nvidiafb, nvidia
06:06.0 FireWire (IEEE 1394): VIA Technologies, Inc. VT6306 Fire II IEEE 1394 OHCI Link Layer Controller (rev 46) (prog-if 10 [OHCI])
Subsystem: VIA Technologies, Inc. VT6306 Fire II IEEE 1394 OHCI Link Layer Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (8000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at d4001000 (32-bit, non-prefetchable) [size=2K]
Region 1: I/O ports at b000 [size=128]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA PME(D0-,D1-,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: ohci1394
Kernel modules: firewire-ohci, ohci1394
06:07.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8169 Gigabit Ethernet (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. RTL-8169 Gigabit Ethernet
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (8000ns min, 16000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at b400 [size=256]
Region 1: Memory at d4000000 (32-bit, non-prefetchable) [size=256]
Expansion ROM at 80000000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: r8169
Kernel modules: r8169
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: sata_nv times out for BD-ROM iHOS104-08
2009-12-22 16:07 sata_nv times out for BD-ROM iHOS104-08 Cengiz Gunay
@ 2009-12-23 7:38 ` Tejun Heo
[not found] ` <d2d378040912232302u4b550dap687fcadced237935@mail.gmail.com>
0 siblings, 1 reply; 28+ messages in thread
From: Tejun Heo @ 2009-12-23 7:38 UTC (permalink / raw)
To: Cengiz Gunay; +Cc: linux-kernel, linux-ide
Hello,
On 12/23/2009 01:07 AM, Cengiz Gunay wrote:
> I was unable to get another driver like the SATA AHCI or one of the PATA
> drivers to take over this device. Is that even possible?
No.
> I would appreciate any suggestions and would happily debug this a little
> further. And, of course, happy holidays everybody. Details of my
> configuration follow.
Can you please try kernel parameter irqpoll? Also, does having a
readable media in the drive during boot make any difference?
Thanks.
--
tejun
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: sata_nv times out for BD-ROM iHOS104-08
[not found] ` <d2d378040912232302u4b550dap687fcadced237935@mail.gmail.com>
@ 2009-12-24 7:25 ` Tejun Heo
2010-01-16 21:34 ` Cengiz Günay
0 siblings, 1 reply; 28+ messages in thread
From: Tejun Heo @ 2009-12-24 7:25 UTC (permalink / raw)
To: Cengiz Günay; +Cc: linux-kernel, linux-ide
On 12/24/2009 04:02 PM, Cengiz Günay wrote:
>
> On Wed, Dec 23, 2009 at 2:38 AM, Tejun Heo <tj@kernel.org
> <mailto:tj@kernel.org>> wrote:
>
> Can you please try kernel parameter irqpoll? Also, does having a
> readable media in the drive during boot make any difference?
>
>
> Sorry, neither made any difference.
>
> By the way, kernel 2.6.23.9 goes into an infinite loop at bootup with
> ata3 exception messages. I can write them down if it would help.
Hmmm... can you please take a photo? I don't think the controller has
anything to do with the issue but just in case can you please try it
with a different controller?
Thanks.
--
tejun
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: sata_nv times out for BD-ROM iHOS104-08
2009-12-24 7:25 ` Tejun Heo
@ 2010-01-16 21:34 ` Cengiz Günay
2010-01-17 15:28 ` Ozan Çağlayan
2010-01-20 2:13 ` Tejun Heo
0 siblings, 2 replies; 28+ messages in thread
From: Cengiz Günay @ 2010-01-16 21:34 UTC (permalink / raw)
To: Tejun Heo; +Cc: linux-kernel, linux-ide
2009/12/24 Tejun Heo <tj@kernel.org>:
> I don't think the controller has anything to do with the issue but
> just in case can you please try it with a different controller?
I tried the iHOS BD-ROM with a VIA VT6412 SATA controller today and it worked:
snippet from dmesg:
---
sata_via 0000:06:06.0: version 2.4
ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16
sata_via 0000:06:06.0: PCI INT A -> Link[APC1] -> GSI 16 (level, low) -> IRQ 16
sata_via 0000:06:06.0: routed to hard irq line 5
scsi0 : sata_via
PM: Adding info for scsi:host0
PM: Adding info for No Bus:host0
scsi1 : sata_via
PM: Adding info for scsi:host1
PM: Adding info for No Bus:host1
scsi2 : sata_via
PM: Adding info for scsi:host2
PM: Adding info for No Bus:host2
ata1: SATA max UDMA/133 port i16@0x9000 bmdma 0xa000 irq 16
ata2: SATA max UDMA/133 port i16@0x9400 bmdma 0xa008 irq 16
ata3: PATA max UDMA/133 port i16@0x9800 bmdma 0xa010 irq 16
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: ATAPI: ATAPI iHOS104, WL08, max UDMA/100
ata1.00: configured for UDMA/100
scsi 0:0:0:0: CD-ROM ATAPI iHOS104 WL08 PQ: 0 ANSI: 5
---
output of lsscsi:
---
[0:0:0:0] cd/dvd ATAPI iHOS104 WL08 /dev/sr0
---
I also tried my sata_nv with a 64-bit kernel 2.6.22-3-amd64. I got
these messages where it looks like ata3 is finally reset and set at a
UDMA/66, but I don't get the drive recognized afterwards:
dmesg:
---
ata3.00: configured for UDMA/100
ata4: SATA link down (SStatus 0 SControl 300)
ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
ata3.00: cmd a0/00:00:00:00:20/00:00:00:00:00/a0 tag 0 cdb 0x12 data 36 in
ata3: soft resetting port
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.00: configured for UDMA/100
ata3: EH complete
ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
ata3.00: cmd a0/00:00:00:00:20/00:00:00:00:00/a0 tag 0 cdb 0x12 data 36 in
ata3: soft resetting port
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.00: configured for UDMA/100
ata3: EH complete
ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
ata3.00: cmd a0/00:00:00:00:20/00:00:00:00:00/a0 tag 0 cdb 0x12 data 36 in
ata3: soft resetting port
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.00: configured for UDMA/100
ata3: EH complete
ata3.00: limiting speed to UDMA/66:PIO4
ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
ata3.00: cmd a0/00:00:00:00:20/00:00:00:00:00/a0 tag 0 cdb 0x12 data 36 in
ata3: soft resetting port
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.00: configured for UDMA/66
ata3: EH complete
hdc: PIONEER DVD-RW DVR-111D, ATAPI CD/DVD-ROM drive
hdc: ATAPI 63X DVD-ROM DVD-R CD-R/RW drive, 2000kB Cache, UDMA(66)
---
I contacted LiteON technical support in the meantime, but they are no
help. They said they tested with one Linux system and it worked.
I will probably buy one of the above VIA cards and use it for this drive.
Thanks for helping!
--
Cengiz
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: sata_nv times out for BD-ROM iHOS104-08
2010-01-16 21:34 ` Cengiz Günay
@ 2010-01-17 15:28 ` Ozan Çağlayan
2010-01-19 9:05 ` Tejun Heo
2010-01-20 2:13 ` Tejun Heo
1 sibling, 1 reply; 28+ messages in thread
From: Ozan Çağlayan @ 2010-01-17 15:28 UTC (permalink / raw)
To: Cengiz Günay; +Cc: Tejun Heo, linux-kernel, linux-ide
Cengiz Günay wrote:
> 2009/12/24 Tejun Heo <tj@kernel.org>:
>> I don't think the controller has anything to do with the issue but
>> just in case can you please try it with a different controller?
>
> I tried the iHOS BD-ROM with a VIA VT6412 SATA controller today and it worked:
>
I don't have the possibility to try with another controller but exactly the same issue with PIONEER DVD-RW DVRKD08RS:
[ 4.618380] ata1.00: ATAPI: PIONEER DVD-RW DVRKD08RS, 1.02, max UDMA/33
[ 4.618447] ata1: nv_mode_filter: 0x739f&0x739f->0x739f, BIOS=0x7000 (0xc000c700) ACPI=0x701f (60:600:0x13)
[ 4.625131] ata1.00: configured for UDMA/33
[ 4.625214] ata1.00: TEST_UNIT_READY failed (err_mask=0x2)
[ 4.838039] usb 3-2: new low speed USB device using ohci_hcd and address 2
[ 4.909709] input: PS/2 Mouse as /devices/platform/i8042/serio1/input/input6
[ 4.944821] input: AlpsPS/2 ALPS GlidePoint as /devices/platform/i8042/serio1/input/input7
[ 5.000029] Clocksource tsc unstable (delta = -254057140 ns)
[ 5.027063] usb 3-2: New USB device found, idVendor=05e3, idProduct=1205
[ 5.027071] usb 3-2: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 5.027078] usb 3-2: Product: USB Mouse
[ 5.027199] usb 3-2: configuration #1 chosen from 1 choice
[ 5.037758] input: USB Mouse as /devices/pci0000:00/0000:00:02.0/usb3/3-2/3-2:1.0/input/input8
[ 5.037936] generic-usb 0003:05E3:1205.0001: input,hidraw0: USB HID v1.10 Mouse [USB Mouse ] on usb-0000:00:02.0-2/input0
[ 5.708253] ieee1394: Host added: ID:BUS[0-00:1023] GUID[00023f7cba403d32]
[ 9.769407] ata1: nv_mode_filter: 0x739f&0x739f->0x739f, BIOS=0x7000 (0xc000c700) ACPI=0x701f (60:600:0x13)
[ 9.775326] ata1.00: configured for UDMA/33
[ 9.775408] ata1.00: TEST_UNIT_READY failed (err_mask=0x2)
[ 9.775417] ata1.00: limiting speed to UDMA/33:PIO3
[ 14.920401] ata1: nv_mode_filter: 0x738f&0x739f->0x738f, BIOS=0x7000 (0xc000c700) ACPI=0x701f (60:600:0x13)
[ 14.926332] ata1.00: configured for UDMA/33
[ 14.926412] ata1.00: TEST_UNIT_READY failed (err_mask=0x2)
[ 14.926418] ata1.00: disabled
[ 14.926452] ata1: soft resetting link
[ 15.077100] ata1: EH complete
[ 15.077155] ata2: port disabled. ignoring.
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: sata_nv times out for BD-ROM iHOS104-08
2010-01-17 15:28 ` Ozan Çağlayan
@ 2010-01-19 9:05 ` Tejun Heo
2010-01-19 9:34 ` Ozan Çağlayan
0 siblings, 1 reply; 28+ messages in thread
From: Tejun Heo @ 2010-01-19 9:05 UTC (permalink / raw)
To: Ozan Çağlayan; +Cc: Cengiz Günay, linux-kernel, linux-ide
[-- Attachment #1: Type: text/plain, Size: 494 bytes --]
Hello,
On 01/18/2010 12:28 AM, Ozan Çağlayan wrote:
> [ 9.769407] ata1: nv_mode_filter: 0x739f&0x739f->0x739f, BIOS=0x7000 (0xc000c700) ACPI=0x701f (60:600:0x13)
> [ 9.775326] ata1.00: configured for UDMA/33
> [ 9.775408] ata1.00: TEST_UNIT_READY failed (err_mask=0x2)
Hmmm... err_mask=0x2 is HSM error. Strange. Does the attached patch
make any difference?
Thanks.
--
tejun
[-- Attachment #2: disable-clear-ua.patch --]
[-- Type: text/x-patch, Size: 747 bytes --]
diff --git a/drivers/ata/libata-eh.c b/drivers/ata/libata-eh.c
index 0ea97c9..df261ac 100644
--- a/drivers/ata/libata-eh.c
+++ b/drivers/ata/libata-eh.c
@@ -3530,7 +3530,7 @@ int ata_eh_recover(struct ata_port *ap, ata_prereset_fn_t prereset,
/* If reset has been issued, clear UA to avoid
* disrupting the current users of the device.
*/
- if (ehc->i.flags & ATA_EHI_DID_RESET) {
+ /*if (ehc->i.flags & ATA_EHI_DID_RESET) {
ata_for_each_dev(dev, link, ALL) {
if (dev->class != ATA_DEV_ATAPI)
continue;
@@ -3538,7 +3538,7 @@ int ata_eh_recover(struct ata_port *ap, ata_prereset_fn_t prereset,
if (rc)
goto dev_fail;
}
- }
+ }*/
/* retry flush if necessary */
ata_for_each_dev(dev, link, ALL) {
^ permalink raw reply related [flat|nested] 28+ messages in thread
* Re: sata_nv times out for BD-ROM iHOS104-08
2010-01-19 9:05 ` Tejun Heo
@ 2010-01-19 9:34 ` Ozan Çağlayan
0 siblings, 0 replies; 28+ messages in thread
From: Ozan Çağlayan @ 2010-01-19 9:34 UTC (permalink / raw)
To: Tejun Heo; +Cc: Cengiz Günay, linux-kernel, linux-ide
Tejun Heo wrote:
> Hello,
>
> On 01/18/2010 12:28 AM, Ozan Çağlayan wrote:
>> [ 9.769407] ata1: nv_mode_filter: 0x739f&0x739f->0x739f, BIOS=0x7000 (0xc000c700) ACPI=0x701f (60:600:0x13)
>> [ 9.775326] ata1.00: configured for UDMA/33
>> [ 9.775408] ata1.00: TEST_UNIT_READY failed (err_mask=0x2)
>
> Hmmm... err_mask=0x2 is HSM error. Strange. Does the attached patch
> make any difference?
Hi,
He reported back that after a few reboots its now working correctly. Actually the behaviour is a little bit
random as he succesfully installed the OS from a CD without losing its DVD drive.
I'll keep a patched kernel and send to him for testing if the bug reappears.
Thanks,
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: sata_nv times out for BD-ROM iHOS104-08
2010-01-16 21:34 ` Cengiz Günay
2010-01-17 15:28 ` Ozan Çağlayan
@ 2010-01-20 2:13 ` Tejun Heo
2010-01-20 2:59 ` Robert Hancock
1 sibling, 1 reply; 28+ messages in thread
From: Tejun Heo @ 2010-01-20 2:13 UTC (permalink / raw)
To: Cengiz Günay; +Cc: linux-kernel, linux-ide, Robert Hancock
Hello, Cengiz.
On 01/17/2010 06:34 AM, Cengiz Günay wrote:
> 2009/12/24 Tejun Heo <tj@kernel.org>:
>> I don't think the controller has anything to do with the issue but
>> just in case can you please try it with a different controller?
>
> I tried the iHOS BD-ROM with a VIA VT6412 SATA controller today and it worked:
Hmm.... it worked? Does kernel parameter sata_nv.adma_enabled=0 make
any difference? Can you please attach boot log with the kernel
parameter specified?
Thanks.
--
tejun
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: sata_nv times out for BD-ROM iHOS104-08
2010-01-20 2:13 ` Tejun Heo
@ 2010-01-20 2:59 ` Robert Hancock
2010-01-22 14:11 ` Cengiz Günay
0 siblings, 1 reply; 28+ messages in thread
From: Robert Hancock @ 2010-01-20 2:59 UTC (permalink / raw)
To: Tejun Heo; +Cc: Cengiz Günay, linux-kernel, linux-ide
2010/1/19 Tejun Heo <tj@kernel.org>:
> Hello, Cengiz.
>
> On 01/17/2010 06:34 AM, Cengiz Günay wrote:
>> 2009/12/24 Tejun Heo <tj@kernel.org>:
>>> I don't think the controller has anything to do with the issue but
>>> just in case can you please try it with a different controller?
>>
>> I tried the iHOS BD-ROM with a VIA VT6412 SATA controller today and it worked:
>
> Hmm.... it worked? Does kernel parameter sata_nv.adma_enabled=0 make
> any difference? Can you please attach boot log with the kernel
> parameter specified?
Think you meant maybe sata_nv.swncq=0 instead - this is an MCP51
controller so it doesn't support ADMA. I don't imagine SWNCQ would
make any difference with an ATAPI device, but wouldn't hurt to try.
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: sata_nv times out for BD-ROM iHOS104-08
2010-01-20 2:59 ` Robert Hancock
@ 2010-01-22 14:11 ` Cengiz Günay
2010-01-23 3:45 ` Tejun Heo
0 siblings, 1 reply; 28+ messages in thread
From: Cengiz Günay @ 2010-01-22 14:11 UTC (permalink / raw)
To: Robert Hancock; +Cc: Tejun Heo, linux-kernel, linux-ide
[-- Attachment #1: Type: text/plain, Size: 1356 bytes --]
Hello, Tejun & Robert,
On Tue, Jan 19, 2010 at 9:59 PM, Robert Hancock <hancockrwd@gmail.com> wrote:
>>> 2009/12/24 Tejun Heo <tj@kernel.org>:
>> Hmm.... it worked? Does kernel parameter sata_nv.adma_enabled=0 make
>> any difference? Can you please attach boot log with the kernel
>> parameter specified?
>
> Think you meant maybe sata_nv.swncq=0 instead - this is an MCP51
> controller so it doesn't support ADMA. I don't imagine SWNCQ would
> make any difference with an ATAPI device, but wouldn't hurt to try.
Thanks for following this up. I tried both of your suggested kernel
parameters (attached). Neither solved my problem, but also it looks
like I couldn't turn off the SWNCQ mode. Even though I set it to zero,
sata_nv still shows that it uses it. Although the order of my devices
changed, so I assume it did something.
I hope this helps shed some light! I will also try the kernel patch --
not sure if that is suited for the problem I'm having?
-Cengiz
--
Cengiz Gunay
--
Postdoctoral Fellow
Prinz Lab, Dept. of Biology, Emory University
1510 Clifton Rd., Room 2172, Atlanta, GA 30322, U.S.A.
cgunay@emory.edu cengique@users.sf.net cengique@yahoo.com
Lab: +1-404-727-9381 Home/Cell: +1-678-559-8694
http://userwww.service.emory.edu/~cgunay
ICQ# 21104923, cengique@{jabber.org,Skype}
--
[-- Attachment #2: dmesg-sata_nv-adma_disabled.log --]
[-- Type: text/x-log, Size: 4224 bytes --]
BIOS-e820: 000000007fef3000 - 000000007ff00000 (ACPI data)
#0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.32 root=/dev/mapper/nvidia_ceebaiib1 ro single sata_nv.adma_enabled=0
Memory: 2052264k/2096064k available (2319k kernel code, 42132k reserved, 912k data, 404k init, 1186760k highmem)
.data : 0xc1243e41 - 0xc1328128 ( 912 kB)
libata version 3.00 loaded.
sata_nv 0000:00:0e.0: version 3.5
sata_nv 0000:00:0e.0: PCI INT A -> Link[APSI] -> GSI 21 (level, low) -> IRQ 21
sata_nv 0000:00:0e.0: Using SWNCQ mode
sata_nv 0000:00:0e.0: setting latency timer to 64
scsi0 : sata_nv
scsi1 : sata_nv
ata1: SATA max UDMA/133 cmd 0x9f0 ctl 0xbf0 bmdma 0xd400 irq 21
ata2: SATA max UDMA/133 cmd 0x970 ctl 0xb70 bmdma 0xd408 irq 21
sata_nv 0000:00:0f.0: PCI INT A -> Link[APSJ] -> GSI 20 (level, low) -> IRQ 20
sata_nv 0000:00:0f.0: Using SWNCQ mode
sata_nv 0000:00:0f.0: setting latency timer to 64
scsi2 : sata_nv
scsi3 : sata_nv
ata3: SATA max UDMA/133 cmd 0x9e0 ctl 0xbe0 bmdma 0xe800 irq 20
ata4: SATA max UDMA/133 cmd 0x960 ctl 0xb60 bmdma 0xe808 irq 20
ata3: SATA link down (SStatus 0 SControl 300)
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: ATA-7: SAMSUNG SP2504C, VT100-41, max UDMA7
ata1.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata1.00: configured for UDMA/133
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2.00: ATA-7: ST3250620AS, 3.AAC, max UDMA/133
ata2.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata2.00: configured for UDMA/133
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: ATAPI: ATAPI iHOS104, WL08, max UDMA/100
ata4.00: configured for UDMA/100
ata4.00: qc timeout (cmd 0xa0)
ata4.00: TEST_UNIT_READY failed (err_mask=0x5)
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for UDMA/100
ata4.00: qc timeout (cmd 0xa0)
ata4.00: TEST_UNIT_READY failed (err_mask=0x5)
ata4: limiting SATA link speed to 1.5 Gbps
ata4.00: limiting speed to UDMA/100:PIO3
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for UDMA/100
ata4.00: qc timeout (cmd 0xa0)
ata4.00: TEST_UNIT_READY failed (err_mask=0x5)
ata4.00: disabled
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4: EH complete
sd 0:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
PM: Adding info for No Bus:sda
sda:
sd 1:0:0:0: [sdb] 488397168 512-byte logical blocks: (250 GB/232 GiB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
PM: Adding info for No Bus:sdb
sdb:
PM: Adding info for No Bus:sdc
PM: Adding info for No Bus:sdd
sd 5:0:0:0: [sdg] 3981312 512-byte logical blocks: (2.03 GB/1.89 GiB)
PM: Adding info for No Bus:sde
PM: Adding info for No Bus:sdf
sd 5:0:0:0: [sdg] Write Protect is off
sd 5:0:0:0: [sdg] Mode Sense: 43 00 00 00
sd 5:0:0:0: [sdg] Assuming drive cache: write through
PM: Adding info for No Bus:sdg
sd 4:0:0:0: [sdc] Attached SCSI removable disk
sd 4:0:0:1: [sdd] Attached SCSI removable disk
sd 4:0:0:2: [sde] Attached SCSI removable disk
sd 4:0:0:3: [sdf] Attached SCSI removable disk
sd 5:0:0:0: [sdg] Assuming drive cache: write through
sdg: sdg1
PM: Adding info for No Bus:sdg1
sd 5:0:0:0: [sdg] Assuming drive cache: write through
sd 5:0:0:0: [sdg] Attached SCSI removable disk
sda1 sda2 sda3 < unknown partition table
sd 1:0:0:0: [sdb] Attached SCSI disk
PM: Adding info for No Bus:sda1
PM: Adding info for No Bus:sda2
PM: Adding info for No Bus:sda3
sd 0:0:0:0: [sda] Attached SCSI disk
EXT3-fs: mounted filesystem with writeback data mode.
hda: task_no_data_intr: status=0x41 { DriveReady Error }
hda: task_no_data_intr: error=0x04 { AbortedCommand }
hda: task_no_data_intr: status=0x41 { DriveReady Error }
hda: task_no_data_intr: error=0x04 { AbortedCommand }
EXT3-fs: mounted filesystem with writeback data mode.
[-- Attachment #3: dmesg-sata_nv-swncq-disabled.log --]
[-- Type: text/x-log, Size: 4193 bytes --]
BIOS-e820: 000000007fef3000 - 000000007ff00000 (ACPI data)
#0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.32 root=/dev/mapper/nvidia_ceebaiib1 ro single sata_nv.swncq=0
Memory: 2052264k/2096064k available (2319k kernel code, 42132k reserved, 912k data, 404k init, 1186760k highmem)
.data : 0xc1243e41 - 0xc1328128 ( 912 kB)
libata version 3.00 loaded.
sata_nv 0000:00:0e.0: version 3.5
sata_nv 0000:00:0e.0: PCI INT A -> Link[APSI] -> GSI 21 (level, low) -> IRQ 21
sata_nv 0000:00:0e.0: Using SWNCQ mode
sata_nv 0000:00:0e.0: setting latency timer to 64
scsi1 : sata_nv
scsi2 : sata_nv
ata1: SATA max UDMA/133 cmd 0x9f0 ctl 0xbf0 bmdma 0xd400 irq 21
ata2: SATA max UDMA/133 cmd 0x970 ctl 0xb70 bmdma 0xd408 irq 21
sata_nv 0000:00:0f.0: PCI INT A -> Link[APSJ] -> GSI 20 (level, low) -> IRQ 20
sata_nv 0000:00:0f.0: Using SWNCQ mode
sata_nv 0000:00:0f.0: setting latency timer to 64
scsi3 : sata_nv
scsi4 : sata_nv
ata3: SATA max UDMA/133 cmd 0x9e0 ctl 0xbe0 bmdma 0xe800 irq 20
ata4: SATA max UDMA/133 cmd 0x960 ctl 0xb60 bmdma 0xe808 irq 20
ata3: SATA link down (SStatus 0 SControl 300)
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: ATA-7: SAMSUNG SP2504C, VT100-41, max UDMA7
ata1.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata1.00: configured for UDMA/133
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2.00: ATA-7: ST3250620AS, 3.AAC, max UDMA/133
ata2.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata2.00: configured for UDMA/133
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: ATAPI: ATAPI iHOS104, WL08, max UDMA/100
ata4.00: configured for UDMA/100
sd 1:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
PM: Adding info for No Bus:sda
sda:
sd 2:0:0:0: [sdb] 488397168 512-byte logical blocks: (250 GB/232 GiB)
sd 2:0:0:0: [sdb] Write Protect is off
sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
PM: Adding info for No Bus:sdb
sdb:
PM: Adding info for No Bus:sdc
PM: Adding info for No Bus:sdd
sda1 sda2 sda3 <
PM: Adding info for No Bus:sde
PM: Adding info for No Bus:sdf
sd 0:0:0:0: [sdc] Attached SCSI removable disk
sd 0:0:0:1: [sdd] Attached SCSI removable disk
sd 0:0:0:2: [sde] Attached SCSI removable disk
sd 0:0:0:3: [sdf] Attached SCSI removable disk
PM: Adding info for No Bus:sda1
PM: Adding info for No Bus:sda2
PM: Adding info for No Bus:sda3
sd 1:0:0:0: [sda] Attached SCSI disk
sd 2:0:0:0: [sdb] Attached SCSI disk
ata4.00: qc timeout (cmd 0xa0)
ata4.00: TEST_UNIT_READY failed (err_mask=0x5)
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for UDMA/100
sd 5:0:0:0: [sdg] 3981312 512-byte logical blocks: (2.03 GB/1.89 GiB)
sd 5:0:0:0: [sdg] Write Protect is off
sd 5:0:0:0: [sdg] Mode Sense: 43 00 00 00
sd 5:0:0:0: [sdg] Assuming drive cache: write through
PM: Adding info for No Bus:sdg
sd 5:0:0:0: [sdg] Assuming drive cache: write through
sdg: sdg1
PM: Adding info for No Bus:sdg1
sd 5:0:0:0: [sdg] Assuming drive cache: write through
sd 5:0:0:0: [sdg] Attached SCSI removable disk
ata4.00: qc timeout (cmd 0xa0)
ata4.00: TEST_UNIT_READY failed (err_mask=0x5)
ata4: limiting SATA link speed to 1.5 Gbps
ata4.00: limiting speed to UDMA/100:PIO3
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for UDMA/100
ata4.00: qc timeout (cmd 0xa0)
ata4.00: TEST_UNIT_READY failed (err_mask=0x5)
ata4.00: disabled
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4: EH complete
EXT3-fs: mounted filesystem with writeback data mode.
hda: task_no_data_intr: status=0x41 { DriveReady Error }
hda: task_no_data_intr: error=0x04 { AbortedCommand }
hda: task_no_data_intr: status=0x41 { DriveReady Error }
hda: task_no_data_intr: error=0x04 { AbortedCommand }
EXT3-fs: mounted filesystem with writeback data mode.
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: sata_nv times out for BD-ROM iHOS104-08
2010-01-22 14:11 ` Cengiz Günay
@ 2010-01-23 3:45 ` Tejun Heo
2010-01-23 21:39 ` Cengiz Günay
0 siblings, 1 reply; 28+ messages in thread
From: Tejun Heo @ 2010-01-23 3:45 UTC (permalink / raw)
To: Cengiz Günay; +Cc: Robert Hancock, linux-kernel, linux-ide
Hello,
On 01/22/2010 11:11 PM, Cengiz Günay wrote:
> On Tue, Jan 19, 2010 at 9:59 PM, Robert Hancock <hancockrwd@gmail.com> wrote:
>>>> 2009/12/24 Tejun Heo <tj@kernel.org>:
>>> Hmm.... it worked? Does kernel parameter sata_nv.adma_enabled=0 make
>>> any difference? Can you please attach boot log with the kernel
>>> parameter specified?
>>
>> Think you meant maybe sata_nv.swncq=0 instead - this is an MCP51
>> controller so it doesn't support ADMA. I don't imagine SWNCQ would
>> make any difference with an ATAPI device, but wouldn't hurt to try.
>
> Thanks for following this up. I tried both of your suggested kernel
> parameters (attached). Neither solved my problem, but also it looks
> like I couldn't turn off the SWNCQ mode. Even though I set it to zero,
> sata_nv still shows that it uses it. Although the order of my devices
> changed, so I assume it did something.
The parameter isn't being passed to the module loaded by initrd. You
probably need to edit modules.conf and then regenerate initrd. :-(
> I hope this helps shed some light! I will also try the kernel patch --
> not sure if that is suited for the problem I'm having?
Yeah, I was about to suggest trying the patch. It could be that the
timeout used by the new TUR code is too aggressive.
Thanks.
--
tejun
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: sata_nv times out for BD-ROM iHOS104-08
2010-01-23 3:45 ` Tejun Heo
@ 2010-01-23 21:39 ` Cengiz Günay
[not found] ` <4B67A149.10406@kernel.org>
0 siblings, 1 reply; 28+ messages in thread
From: Cengiz Günay @ 2010-01-23 21:39 UTC (permalink / raw)
To: Tejun Heo; +Cc: Robert Hancock, linux-kernel, linux-ide
[-- Attachment #1: Type: text/plain, Size: 703 bytes --]
Hello,
2010/1/22 Tejun Heo <tj@kernel.org>:
> The parameter isn't being passed to the module loaded by initrd. You
> probably need to edit modules.conf and then regenerate initrd. :-(
Ok, you're right. I forgot I had to do that. So now I did it for
ADMA=0, SWNCQ=0 and MSI=1, separately. None worked, and all dmesg
outputs attached.
> Yeah, I was about to suggest trying the patch. It could be that the
> timeout used by the new TUR code is too aggressive.
Unfortunately that didn't work, either (attached). It kept on changing
DMA modes down to PIO0 and completly failed in the end. Should I try
different sata_nv parameters with this patch if needed?
Thanks,
--
Cengiz
[-- Attachment #2: dmesg-sata_nv-adma_disabled_no_initrd.log --]
[-- Type: text/x-log, Size: 4224 bytes --]
BIOS-e820: 000000007fef3000 - 000000007ff00000 (ACPI data)
#0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.32 root=/dev/mapper/nvidia_ceebaiib1 ro single sata_nv.adma_enabled=0
Memory: 2052264k/2096064k available (2319k kernel code, 42132k reserved, 912k data, 404k init, 1186760k highmem)
.data : 0xc1243e41 - 0xc1328128 ( 912 kB)
libata version 3.00 loaded.
sata_nv 0000:00:0e.0: version 3.5
sata_nv 0000:00:0e.0: PCI INT A -> Link[APSI] -> GSI 21 (level, low) -> IRQ 21
sata_nv 0000:00:0e.0: Using SWNCQ mode
sata_nv 0000:00:0e.0: setting latency timer to 64
scsi1 : sata_nv
scsi2 : sata_nv
ata1: SATA max UDMA/133 cmd 0x9f0 ctl 0xbf0 bmdma 0xd400 irq 21
ata2: SATA max UDMA/133 cmd 0x970 ctl 0xb70 bmdma 0xd408 irq 21
sata_nv 0000:00:0f.0: PCI INT A -> Link[APSJ] -> GSI 20 (level, low) -> IRQ 20
sata_nv 0000:00:0f.0: Using SWNCQ mode
sata_nv 0000:00:0f.0: setting latency timer to 64
scsi3 : sata_nv
scsi4 : sata_nv
ata3: SATA max UDMA/133 cmd 0x9e0 ctl 0xbe0 bmdma 0xe800 irq 20
ata4: SATA max UDMA/133 cmd 0x960 ctl 0xb60 bmdma 0xe808 irq 20
ata3: SATA link down (SStatus 0 SControl 300)
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: ATA-7: SAMSUNG SP2504C, VT100-41, max UDMA7
ata1.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata1.00: configured for UDMA/133
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2.00: ATA-7: ST3250620AS, 3.AAC, max UDMA/133
ata2.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata2.00: configured for UDMA/133
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: ATAPI: ATAPI iHOS104, WL08, max UDMA/100
ata4.00: configured for UDMA/100
sd 1:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
PM: Adding info for No Bus:sda
sd 2:0:0:0: [sdb] 488397168 512-byte logical blocks: (250 GB/232 GiB)
sda:
sd 2:0:0:0: [sdb] Write Protect is off
sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
PM: Adding info for No Bus:sdb
sdb:
PM: Adding info for No Bus:sdc
PM: Adding info for No Bus:sdd
PM: Adding info for No Bus:sde
sd 0:0:0:0: [sdc] Attached SCSI removable disk
sd 0:0:0:1: [sdd] Attached SCSI removable disk
PM: Adding info for No Bus:sdf
sd 0:0:0:2: [sde] Attached SCSI removable disk
sd 0:0:0:3: [sdf] Attached SCSI removable disk
sda1 sda2 sda3 < unknown partition table
sd 2:0:0:0: [sdb] Attached SCSI disk
PM: Adding info for No Bus:sda1
PM: Adding info for No Bus:sda2
PM: Adding info for No Bus:sda3
sd 1:0:0:0: [sda] Attached SCSI disk
ata4.00: qc timeout (cmd 0xa0)
ata4.00: TEST_UNIT_READY failed (err_mask=0x5)
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for UDMA/100
sd 5:0:0:0: [sdg] 3981312 512-byte logical blocks: (2.03 GB/1.89 GiB)
sd 5:0:0:0: [sdg] Write Protect is off
sd 5:0:0:0: [sdg] Mode Sense: 43 00 00 00
sd 5:0:0:0: [sdg] Assuming drive cache: write through
PM: Adding info for No Bus:sdg
sd 5:0:0:0: [sdg] Assuming drive cache: write through
sdg: sdg1
PM: Adding info for No Bus:sdg1
sd 5:0:0:0: [sdg] Assuming drive cache: write through
sd 5:0:0:0: [sdg] Attached SCSI removable disk
ata4.00: qc timeout (cmd 0xa0)
ata4.00: TEST_UNIT_READY failed (err_mask=0x5)
ata4: limiting SATA link speed to 1.5 Gbps
ata4.00: limiting speed to UDMA/100:PIO3
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for UDMA/100
ata4.00: qc timeout (cmd 0xa0)
ata4.00: TEST_UNIT_READY failed (err_mask=0x5)
ata4.00: disabled
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4: EH complete
EXT3-fs: mounted filesystem with writeback data mode.
hda: task_no_data_intr: status=0x41 { DriveReady Error }
hda: task_no_data_intr: error=0x04 { AbortedCommand }
hda: task_no_data_intr: status=0x41 { DriveReady Error }
hda: task_no_data_intr: error=0x04 { AbortedCommand }
EXT3-fs: mounted filesystem with writeback data mode.
[-- Attachment #3: dmesg-sata_nv-swncq-disabled_in_initrd.log --]
[-- Type: text/x-log, Size: 4562 bytes --]
BIOS-e820: 000000007fef3000 - 000000007ff00000 (ACPI data)
#0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
Memory: 2052264k/2096064k available (2319k kernel code, 42136k reserved, 912k data, 404k init, 1186760k highmem)
.data : 0xc1243e41 - 0xc1328128 ( 912 kB)
libata version 3.00 loaded.
sata_nv 0000:00:0e.0: version 3.5
sata_nv 0000:00:0e.0: PCI INT A -> Link[APSI] -> GSI 23 (level, low) -> IRQ 23
sata_nv 0000:00:0e.0: setting latency timer to 64
scsi0 : sata_nv
scsi1 : sata_nv
ata1: SATA max UDMA/133 cmd 0x9f0 ctl 0xbf0 bmdma 0xd400 irq 23
ata2: SATA max UDMA/133 cmd 0x970 ctl 0xb70 bmdma 0xd408 irq 23
sata_nv 0000:00:0f.0: PCI INT A -> Link[APSJ] -> GSI 22 (level, low) -> IRQ 22
sata_nv 0000:00:0f.0: setting latency timer to 64
scsi2 : sata_nv
scsi3 : sata_nv
ata3: SATA max UDMA/133 cmd 0x9e0 ctl 0xbe0 bmdma 0xe800 irq 22
ata4: SATA max UDMA/133 cmd 0x960 ctl 0xb60 bmdma 0xe808 irq 22
ata3: SATA link down (SStatus 0 SControl 300)
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: ATA-7: SAMSUNG SP2504C, VT100-41, max UDMA7
ata1.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata1.00: configured for UDMA/133
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2.00: ATA-7: ST3250620AS, 3.AAC, max UDMA/133
ata2.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata2.00: configured for UDMA/133
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: ATAPI: ATAPI iHOS104, WL08, max UDMA/100
ata4.00: configured for UDMA/100
ata4.00: qc timeout (cmd 0xa0)
ata4.00: TEST_UNIT_READY failed (err_mask=0x5)
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for UDMA/100
ata4.00: qc timeout (cmd 0xa0)
ata4.00: TEST_UNIT_READY failed (err_mask=0x5)
ata4: limiting SATA link speed to 1.5 Gbps
ata4.00: limiting speed to UDMA/100:PIO3
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for UDMA/100
ata4.00: qc timeout (cmd 0xa0)
ata4.00: TEST_UNIT_READY failed (err_mask=0x5)
ata4.00: disabled
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4: EH complete
pata_amd 0000:00:0d.0: version 0.4.1
pata_amd 0000:00:0d.0: setting latency timer to 64
scsi4 : pata_amd
scsi5 : pata_amd
ata5: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xf000 irq 14
ata6: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xf008 irq 15
ata5: port disabled. ignoring.
sd 0:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
PM: Adding info for No Bus:sda
sda:
sd 1:0:0:0: [sdb] 488397168 512-byte logical blocks: (250 GB/232 GiB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
PM: Adding info for No Bus:sdb
sdb: sda1 sda2 sda3 <
PM: Adding info for No Bus:sda1
PM: Adding info for No Bus:sda2
PM: Adding info for No Bus:sda3
sd 0:0:0:0: [sda] Attached SCSI disk
sd 1:0:0:0: [sdb] Attached SCSI disk
ata6.00: ATAPI: PIONEER DVD-RW DVR-111D, 1.23, max UDMA/66
ata6: nv_mode_filter: 0x1f39f&0x1f39f->0x1f39f, BIOS=0x1f000 (0xc500) ACPI=0x1f01f (30:600:0x13)
ata6.00: configured for UDMA/66
EXT3-fs: mounted filesystem with writeback data mode.
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 1:0:0:0: Attached scsi generic sg1 type 0
sd 6:0:0:0: Attached scsi generic sg3 type 0
sd 6:0:0:1: Attached scsi generic sg4 type 0
PM: Adding info for No Bus:sdc
PM: Adding info for No Bus:sdd
sd 6:0:0:2: Attached scsi generic sg5 type 0
sd 6:0:0:0: [sdc] Attached SCSI removable disk
sd 6:0:0:1: [sdd] Attached SCSI removable disk
sd 6:0:0:3: Attached scsi generic sg6 type 0
PM: Adding info for No Bus:sde
PM: Adding info for No Bus:sdf
sd 6:0:0:2: [sde] Attached SCSI removable disk
sd 6:0:0:3: [sdf] Attached SCSI removable disk
EXT3-fs: mounted filesystem with writeback data mode.
sd 7:0:0:0: Attached scsi generic sg7 type 0
sd 7:0:0:0: [sdg] 3981312 512-byte logical blocks: (2.03 GB/1.89 GiB)
sd 7:0:0:0: [sdg] Write Protect is off
sd 7:0:0:0: [sdg] Mode Sense: 43 00 00 00
sd 7:0:0:0: [sdg] Assuming drive cache: write through
PM: Adding info for No Bus:sdg
sd 7:0:0:0: [sdg] Assuming drive cache: write through
sdg: sdg1
PM: Adding info for No Bus:sdg1
sd 7:0:0:0: [sdg] Assuming drive cache: write through
sd 7:0:0:0: [sdg] Attached SCSI removable disk
[-- Attachment #4: dmesg-sata_nv-swncq-0-msi-1_in_initrd.log --]
[-- Type: text/x-log, Size: 4650 bytes --]
BIOS-e820: 000000007fef3000 - 000000007ff00000 (ACPI data)
#0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
Memory: 2052264k/2096064k available (2319k kernel code, 42136k reserved, 912k data, 404k init, 1186760k highmem)
.data : 0xc1243e41 - 0xc1328128 ( 912 kB)
libata version 3.00 loaded.
sata_nv 0000:00:0e.0: version 3.5
sata_nv 0000:00:0e.0: PCI INT A -> Link[APSI] -> GSI 23 (level, low) -> IRQ 23
sata_nv 0000:00:0e.0: Using MSI
sata_nv 0000:00:0e.0: setting latency timer to 64
scsi0 : sata_nv
scsi1 : sata_nv
ata1: SATA max UDMA/133 cmd 0x9f0 ctl 0xbf0 bmdma 0xd400 irq 23
ata2: SATA max UDMA/133 cmd 0x970 ctl 0xb70 bmdma 0xd408 irq 23
sata_nv 0000:00:0f.0: PCI INT A -> Link[APSJ] -> GSI 22 (level, low) -> IRQ 22
sata_nv 0000:00:0f.0: Using MSI
sata_nv 0000:00:0f.0: setting latency timer to 64
scsi2 : sata_nv
scsi3 : sata_nv
ata3: SATA max UDMA/133 cmd 0x9e0 ctl 0xbe0 bmdma 0xe800 irq 22
ata4: SATA max UDMA/133 cmd 0x960 ctl 0xb60 bmdma 0xe808 irq 22
ata3: SATA link down (SStatus 0 SControl 300)
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: ATA-7: SAMSUNG SP2504C, VT100-41, max UDMA7
ata1.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata1.00: configured for UDMA/133
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2.00: ATA-7: ST3250620AS, 3.AAC, max UDMA/133
ata2.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata2.00: configured for UDMA/133
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: ATAPI: ATAPI iHOS104, WL08, max UDMA/100
ata4.00: configured for UDMA/100
ata4.00: qc timeout (cmd 0xa0)
ata4.00: TEST_UNIT_READY failed (err_mask=0x5)
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for UDMA/100
ata4.00: qc timeout (cmd 0xa0)
ata4.00: TEST_UNIT_READY failed (err_mask=0x5)
ata4: limiting SATA link speed to 1.5 Gbps
ata4.00: limiting speed to UDMA/100:PIO3
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for UDMA/100
ata4.00: qc timeout (cmd 0xa0)
ata4.00: TEST_UNIT_READY failed (err_mask=0x5)
ata4.00: disabled
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4: EH complete
pata_amd 0000:00:0d.0: version 0.4.1
pata_amd 0000:00:0d.0: setting latency timer to 64
scsi4 : pata_amd
scsi5 : pata_amd
ata5: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xf000 irq 14
ata6: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xf008 irq 15
ata5: port disabled. ignoring.
sd 0:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:0:0:0: [sdb] 488397168 512-byte logical blocks: (250 GB/232 GiB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
PM: Adding info for No Bus:sdb
sdb:
PM: Adding info for No Bus:sda
sda: sda1 sda2 sda3 < unknown partition table
sd 1:0:0:0: [sdb] Attached SCSI disk
PM: Adding info for No Bus:sda1
PM: Adding info for No Bus:sda2
PM: Adding info for No Bus:sda3
sd 0:0:0:0: [sda] Attached SCSI disk
ata6.00: ATAPI: PIONEER DVD-RW DVR-111D, 1.23, max UDMA/66
ata6: nv_mode_filter: 0x1f39f&0x1f39f->0x1f39f, BIOS=0x1f000 (0xc500) ACPI=0x1f01f (30:600:0x13)
ata6.00: configured for UDMA/66
EXT3-fs: mounted filesystem with writeback data mode.
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 1:0:0:0: Attached scsi generic sg1 type 0
sd 6:0:0:0: Attached scsi generic sg3 type 0
sd 6:0:0:1: Attached scsi generic sg4 type 0
PM: Adding info for No Bus:sdc
sd 6:0:0:2: Attached scsi generic sg5 type 0
PM: Adding info for No Bus:sdd
sd 6:0:0:0: [sdc] Attached SCSI removable disk
sd 6:0:0:3: Attached scsi generic sg6 type 0
sd 6:0:0:1: [sdd] Attached SCSI removable disk
PM: Adding info for No Bus:sde
PM: Adding info for No Bus:sdf
sd 6:0:0:2: [sde] Attached SCSI removable disk
sd 6:0:0:3: [sdf] Attached SCSI removable disk
EXT3-fs: mounted filesystem with writeback data mode.
sd 7:0:0:0: Attached scsi generic sg7 type 0
sd 7:0:0:0: [sdg] 3981312 512-byte logical blocks: (2.03 GB/1.89 GiB)
sd 7:0:0:0: [sdg] Write Protect is off
sd 7:0:0:0: [sdg] Mode Sense: 43 00 00 00
sd 7:0:0:0: [sdg] Assuming drive cache: write through
PM: Adding info for No Bus:sdg
sd 7:0:0:0: [sdg] Assuming drive cache: write through
sdg: sdg1
PM: Adding info for No Bus:sdg1
sd 7:0:0:0: [sdg] Assuming drive cache: write through
sd 7:0:0:0: [sdg] Attached SCSI removable disk
[-- Attachment #5: dmesg-sata_nv-disable-clear-ua.log --]
[-- Type: text/x-log, Size: 40543 bytes --]
libata version 3.00 loaded.
sata_nv 0000:00:0e.0: version 3.5
sata_nv 0000:00:0e.0: PCI INT A -> Link[APSI] -> GSI 21 (level, low) -> IRQ 21
sata_nv 0000:00:0e.0: Using SWNCQ mode
sata_nv 0000:00:0e.0: setting latency timer to 64
scsi0 : sata_nv
scsi1 : sata_nv
ata1: SATA max UDMA/133 cmd 0x9f0 ctl 0xbf0 bmdma 0xd400 irq 21
ata2: SATA max UDMA/133 cmd 0x970 ctl 0xb70 bmdma 0xd408 irq 21
sata_nv 0000:00:0f.0: PCI INT A -> Link[APSJ] -> GSI 20 (level, low) -> IRQ 20
sata_nv 0000:00:0f.0: Using SWNCQ mode
sata_nv 0000:00:0f.0: setting latency timer to 64
scsi2 : sata_nv
scsi3 : sata_nv
ata3: SATA max UDMA/133 cmd 0x9e0 ctl 0xbe0 bmdma 0xe800 irq 20
ata4: SATA max UDMA/133 cmd 0x960 ctl 0xb60 bmdma 0xe808 irq 20
ata3: SATA link down (SStatus 0 SControl 300)
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: ATA-7: SAMSUNG SP2504C, VT100-41, max UDMA7
ata1.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata1.00: configured for UDMA/133
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2.00: ATA-7: ST3250620AS, 3.AAC, max UDMA/133
ata2.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata2.00: configured for UDMA/133
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: ATAPI: ATAPI iHOS104, WL08, max UDMA/100
ata4.00: configured for UDMA/100
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for UDMA/100
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4: limiting SATA link speed to 1.5 Gbps
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for UDMA/100
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: limiting speed to UDMA/66:PIO4
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for UDMA/66
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: limiting speed to UDMA/33:PIO4
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for UDMA/33
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: limiting speed to PIO4
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO4
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: limiting speed to PIO3
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO3
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: limiting speed to PIO0
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
sd 0:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
PM: Adding info for No Bus:sda
sda:
sd 1:0:0:0: [sdb] 488397168 512-byte logical blocks: (250 GB/232 GiB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
PM: Adding info for No Bus:sdb
sdb:
PM: Adding info for No Bus:sdc
sd 5:0:0:0: [sdg] 3981312 512-byte logical blocks: (2.03 GB/1.89 GiB)
PM: Adding info for No Bus:sdd
PM: Adding info for No Bus:sde
sd 5:0:0:0: [sdg] Write Protect is off
sd 5:0:0:0: [sdg] Mode Sense: 43 00 00 00
sd 5:0:0:0: [sdg] Assuming drive cache: write through
PM: Adding info for No Bus:sdg
sd 4:0:0:0: [sdc] Attached SCSI removable disk
sd 4:0:0:1: [sdd] Attached SCSI removable disk
PM: Adding info for No Bus:sdf
sd 4:0:0:2: [sde] Attached SCSI removable disk
sd 5:0:0:0: [sdg] Assuming drive cache: write through
sdg:
sd 4:0:0:3: [sdf] Attached SCSI removable disk
sdg1
PM: Adding info for No Bus:sdg1
sd 1:0:0:0: [sdb] Attached SCSI disk
sd 5:0:0:0: [sdg] Assuming drive cache: write through
sd 5:0:0:0: [sdg] Attached SCSI removable disk
sda1 sda2 sda3 < >
PM: Adding info for No Bus:sda1
PM: Adding info for No Bus:sda2
PM: Adding info for No Bus:sda3
sd 0:0:0:0: [sda] Attached SCSI disk
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
[<f903e13a>] ? init_sd+0x13a/0x17a [sd_mod]
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: WARNING: synchronous SCSI scan failed without making any progress,
ata4: EH complete
EXT3-fs: mounted filesystem with writeback data mode.
hda: task_no_data_intr: status=0x41 { DriveReady Error }
hda: task_no_data_intr: error=0x04 { AbortedCommand }
hda: task_no_data_intr: status=0x41 { DriveReady Error }
hda: task_no_data_intr: error=0x04 { AbortedCommand }
EXT3-fs: mounted filesystem with writeback data mode.
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: sata_nv times out for BD-ROM iHOS104-08
[not found] ` <4B67A149.10406@kernel.org>
@ 2010-02-17 16:14 ` Cengiz Günay
2010-02-18 1:50 ` Tejun Heo
0 siblings, 1 reply; 28+ messages in thread
From: Cengiz Günay @ 2010-02-17 16:14 UTC (permalink / raw)
To: Tejun Heo; +Cc: Robert Hancock, linux-kernel, linux-ide
[-- Attachment #1: Type: text/plain, Size: 558 bytes --]
2010/2/1 Tejun Heo <tj@kernel.org>:
> Can you please attach full dmesg w/ the patch applied w/o any kernel
> parameter? I'm curious where the hda warnings are coming from. Is
> generic IDE driver loaded?
The dmesg snippet I attached last time was w/o any kernel parameters.
This time I'm attaching the full dmesg output. hda is my other DVD-RW
drive, I'm not sure what the warnings mean. ide_core is loaded, but
not the ide-generic or ide-pci-generic modules, although they are
available. Would you like me to force them to load?
-Cengiz
[-- Attachment #2: dmesg-sata_nv-disable-clear-ua-full.log --]
[-- Type: text/x-log, Size: 119749 bytes --]
Linux version 2.6.32testing (root@salon) (gcc version 4.3.3 (Debian 4.3.3-10) ) #2 SMP PREEMPT Sat Jan 23 13:29:25 EST 2010
KERNEL supported cpus:
Intel GenuineIntel
AMD AuthenticAMD
NSC Geode by NSC
Cyrix CyrixInstead
Centaur CentaurHauls
Transmeta GenuineTMx86
Transmeta TransmetaCPU
UMC UMC UMC UMC
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009c400 (usable)
BIOS-e820: 000000000009c400 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000007fef0000 (usable)
BIOS-e820: 000000007fef0000 - 000000007fef3000 (ACPI NVS)
BIOS-e820: 000000007fef3000 - 000000007ff00000 (ACPI data)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
DMI 2.4 present.
Phoenix BIOS detected: BIOS may corrupt low RAM, working around it.
e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
last_pfn = 0x7fef0 max_arch_pfn = 0x100000
MTRR default type: uncachable
MTRR fixed ranges enabled:
00000-9FFFF write-back
A0000-BFFFF uncachable
C0000-CDFFF write-protect
CE000-FFFFF uncachable
MTRR variable ranges enabled:
0 base 000000000 mask F80000000 write-back
1 base 07FF00000 mask FFFF00000 uncachable
2 disabled
3 disabled
4 disabled
5 disabled
6 disabled
7 disabled
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
initial memory mapped : 0 - 01800000
init_memory_mapping: 0000000000000000-00000000377fe000
0000000000 - 0000400000 page 4k
0000400000 - 0037400000 page 2M
0037400000 - 00377fe000 page 4k
kernel direct mapping tables up to 377fe000 @ 10000-15000
RAMDISK: 36bae000 - 37fefa84
Allocated new RAMDISK: 013e6000 - 02827a84
Move RAMDISK from 0000000036bae000 - 0000000037fefa83 to 013e6000 - 02827a83
ACPI: RSDP 000f7900 00024 (v02 Nvidia)
ACPI: XSDT 7fef30c0 0004C (v01 Nvidia ASUSACPI 42302E31 AWRD 00000000)
ACPI: FACP 7fefa600 000F4 (v03 Nvidia ASUSACPI 42302E31 AWRD 00000000)
ACPI: DSDT 7fef3240 07354 (v01 NVIDIA ASUSACPI 00001000 MSFT 03000000)
ACPI: FACS 7fef0000 00040
ACPI: HPET 7fefa840 00038 (v01 Nvidia ASUSACPI 42302E31 AWRD 00000098)
ACPI: MCFG 7fefa8c0 0003C (v01 Nvidia ASUSACPI 42302E31 AWRD 00000000)
ACPI: APIC 7fefa740 0008E (v01 Nvidia ASUSACPI 42302E31 AWRD 00000000)
ACPI: SSDT 7fefae20 0032C (v01 Nvidia ASUSACPI 42302E31 AWRD 00000000)
ACPI: Local APIC address 0xfee00000
1158MB HIGHMEM available.
887MB LOWMEM available.
mapped low ram: 0 - 377fe000
low ram: 0 - 377fe000
node 0 low ram: 00000000 - 377fe000
node 0 bootmap 00011000 - 00017f00
(9 early reservations) ==> bootmem [0000000000 - 00377fe000]
#0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
#1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000]
#2 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 - 0000007000]
#3 [0001000000 - 00013de7c4] TEXT DATA BSS ==> [0001000000 - 00013de7c4]
#4 [000009c400 - 0000100000] BIOS reserved ==> [000009c400 - 0000100000]
#5 [00013df000 - 00013e5149] BRK ==> [00013df000 - 00013e5149]
#6 [0000010000 - 0000011000] PGTABLE ==> [0000010000 - 0000011000]
#7 [00013e6000 - 0002827a84] NEW RAMDISK ==> [00013e6000 - 0002827a84]
#8 [0000011000 - 0000018000] BOOTMAP ==> [0000011000 - 0000018000]
found SMP MP-table at [c00f5d50] f5d50
Zone PFN ranges:
DMA 0x00000010 -> 0x00001000
Normal 0x00001000 -> 0x000377fe
HighMem 0x000377fe -> 0x0007fef0
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
0: 0x00000010 -> 0x0000009c
0: 0x00000100 -> 0x0007fef0
On node 0 totalpages: 523900
free_area_init_node: node 0, pgdat c1324fc0, node_mem_map c2829200
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 3948 pages, LIFO batch:0
Normal zone: 1744 pages used for memmap
Normal zone: 221486 pages, LIFO batch:31
HighMem zone: 2318 pages used for memmap
HighMem zone: 294372 pages, LIFO batch:31
Using APIC driver default
ACPI: PM-Timer IO Port: 0x4008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 4, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
ACPI: IRQ9 used by override.
ACPI: IRQ14 used by override.
ACPI: IRQ15 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
ACPI: HPET id: 0x10de8201 base: 0xfeff0000
SMP: Allowing 4 CPUs, 2 hotplug CPUs
nr_irqs_gsi: 24
PM: Registered nosave memory: 000000000009c000 - 000000000009d000
PM: Registered nosave memory: 000000000009d000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
Allocating PCI resources starting at 7ff00000 (gap: 7ff00000:60100000)
NR_CPUS:4 nr_cpumask_bits:4 nr_cpu_ids:4 nr_node_ids:1
PERCPU: Embedded 11 pages/cpu @c3c00000 s23512 r0 d21544 u1048576
pcpu-alloc: s23512 r0 d21544 u1048576 alloc=1*4194304
pcpu-alloc: [0] 0 1 2 3
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 519806
Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.32testing root=/dev/mapper/nvidia_ceebaiib1 ro single
PID hash table entries: 4096 (order: 2, 16384 bytes)
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
Initializing HighMem for node 0 (000377fe:0007fef0)
Memory: 2052264k/2096064k available (2319k kernel code, 42156k reserved, 912k data, 404k init, 1186760k highmem)
virtual kernel memory layout:
fixmap : 0xfff6b000 - 0xfffff000 ( 592 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xf7ffe000 - 0xff7fe000 ( 120 MB)
lowmem : 0xc0000000 - 0xf77fe000 ( 887 MB)
.init : 0xc1329000 - 0xc138e000 ( 404 kB)
.data : 0xc1243e41 - 0xc1328128 ( 912 kB)
.text : 0xc1000000 - 0xc1243e41 (2319 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:384
Extended CMOS year: 2000
spurious 8259A interrupt: IRQ7.
Console: colour VGA+ 80x25
console [tty0] enabled
hpet clockevent registered
Fast TSC calibration using PIT
Detected 2133.606 MHz processor.
Calibrating delay loop (skipped), value calculated using timer frequency.. 4267.21 BogoMIPS (lpj=2133606)
Security Framework initialized
Mount-cache hash table entries: 512
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
mce: CPU supports 6 MCE banks
CPU0: Thermal monitoring enabled (TM2)
using mwait in idle threads.
Checking 'hlt' instruction... OK.
ACPI: Core revision 20090903
..TIMER: vector=0x30 apic1=0 pin1=0 apic2=-1 pin2=-1
..MP-BIOS bug: 8254 timer not connected to IO-APIC
...trying to set up timer (IRQ0) through the 8259A ...
..... (found apic 0 pin 0) ...
....... works.
CPU0: Intel(R) Core(TM)2 CPU 6400 @ 2.13GHz stepping 06
Booting processor 1 APIC 0x1 ip 0x6000
Initializing CPU#1
Calibrating delay using timer specific routine.. 4266.57 BogoMIPS (lpj=2133288)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU1: Thermal monitoring enabled (TM2)
CPU1: Intel(R) Core(TM)2 CPU 6400 @ 2.13GHz stepping 06
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Brought up 2 CPUs
Total of 2 processors activated (8533.78 BogoMIPS).
CPU0 attaching sched-domain:
domain 0: span 0-1 level MC
groups: 0 1
CPU1 attaching sched-domain:
domain 0: span 0-1 level MC
groups: 1 0
PM: Adding info for No Bus:platform
Time: 10:38:08 Date: 02/17/10
NET: Registered protocol family 16
PM: Adding info for No Bus:vtcon0
EISA bus registered
ACPI: bus type pci registered
PM: Adding info for No Bus:id
PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
PCI: MCFG area at e0000000 reserved in E820
PCI: Using MMCONFIG for extended config space
PCI: Using configuration type 1 for base access
PM: Adding info for No Bus:default
bio: create slab <bio-0> at 0
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
PM: Adding info for acpi:LNXSYSTM:00
PM: Adding info for acpi:LNXCPU:00
PM: Adding info for acpi:LNXCPU:01
PM: Adding info for acpi:LNXCPU:02
PM: Adding info for acpi:LNXCPU:03
PM: Adding info for acpi:LNXSYBUS:00
PM: Adding info for acpi:PNP0C0C:00
PM: Adding info for acpi:PNP0A08:00
PM: Adding info for acpi:PNP0C02:00
PM: Adding info for acpi:device:00
PM: Adding info for acpi:device:01
PM: Adding info for acpi:device:02
PM: Adding info for acpi:device:03
PM: Adding info for acpi:device:04
PM: Adding info for acpi:device:05
PM: Adding info for acpi:device:06
PM: Adding info for acpi:device:07
PM: Adding info for acpi:device:08
PM: Adding info for acpi:device:09
PM: Adding info for acpi:device:0a
PM: Adding info for acpi:device:0b
PM: Adding info for acpi:device:0c
PM: Adding info for acpi:device:0d
PM: Adding info for acpi:device:0e
PM: Adding info for acpi:device:0f
PM: Adding info for acpi:device:10
PM: Adding info for acpi:device:11
PM: Adding info for acpi:device:12
PM: Adding info for acpi:device:13
PM: Adding info for acpi:device:14
PM: Adding info for acpi:device:15
PM: Adding info for acpi:device:16
PM: Adding info for acpi:device:17
PM: Adding info for acpi:device:18
PM: Adding info for acpi:device:19
PM: Adding info for acpi:PNP0C02:01
PM: Adding info for acpi:PNP0000:00
PM: Adding info for acpi:PNP0200:00
PM: Adding info for acpi:PNP0100:00
PM: Adding info for acpi:PNP0103:00
PM: Adding info for acpi:PNP0B00:00
PM: Adding info for acpi:PNP0800:00
PM: Adding info for acpi:PNP0C04:00
PM: Adding info for acpi:device:1a
PM: Adding info for acpi:device:1b
PM: Adding info for acpi:device:1c
PM: Adding info for acpi:device:1d
PM: Adding info for acpi:device:1e
PM: Adding info for acpi:device:1f
PM: Adding info for acpi:NVRAIDBUS:00
PM: Adding info for acpi:ATK0110:00
PM: Adding info for acpi:PNP0C0F:00
PM: Adding info for acpi:PNP0C0F:01
PM: Adding info for acpi:PNP0C0F:02
PM: Adding info for acpi:PNP0C0F:03
PM: Adding info for acpi:PNP0C0F:04
PM: Adding info for acpi:PNP0C0F:05
PM: Adding info for acpi:PNP0C0F:06
PM: Adding info for acpi:PNP0C0F:07
PM: Adding info for acpi:PNP0C0F:08
PM: Adding info for acpi:PNP0C0F:09
PM: Adding info for acpi:PNP0C0F:0a
PM: Adding info for acpi:PNP0C0F:0b
PM: Adding info for acpi:PNP0C0F:0c
PM: Adding info for acpi:PNP0C0F:0d
PM: Adding info for acpi:PNP0C0F:0e
PM: Adding info for acpi:PNP0C0F:0f
PM: Adding info for acpi:PNP0C0F:10
PM: Adding info for acpi:PNP0C0F:11
PM: Adding info for acpi:PNP0C0F:12
PM: Adding info for acpi:PNP0C0F:13
PM: Adding info for acpi:PNP0C0F:14
PM: Adding info for acpi:PNP0C0F:15
PM: Adding info for acpi:PNP0C0F:16
PM: Adding info for acpi:PNP0C0F:17
PM: Adding info for acpi:PNP0C0F:18
PM: Adding info for acpi:PNP0C0F:19
PM: Adding info for acpi:PNP0C0F:1a
PM: Adding info for acpi:PNP0C0F:1b
PM: Adding info for acpi:PNP0C0F:1c
PM: Adding info for acpi:PNP0C0F:1d
PM: Adding info for acpi:PNP0C0F:1e
PM: Adding info for acpi:PNP0C0F:1f
PM: Adding info for acpi:PNP0C0F:20
PM: Adding info for acpi:PNP0C0F:21
PM: Adding info for acpi:PNP0C0F:22
PM: Adding info for acpi:PNP0C0F:23
PM: Adding info for acpi:PNP0C0F:24
PM: Adding info for acpi:PNP0C0F:25
PM: Adding info for acpi:PNP0C0F:26
PM: Adding info for acpi:PNP0C0F:27
PM: Adding info for acpi:PNP0C0F:28
PM: Adding info for acpi:PNP0C02:02
PM: Adding info for acpi:PNP0C01:00
PM: Adding info for acpi:LNXTHERM:00
PM: Adding info for acpi:PNP0C0B:00
PM: Adding info for acpi:LNXTHERM:01
PM: Adding info for acpi:LNXPWRBN:00
ACPI: No dock devices found.
ACPI: PCI Root Bridge [PCI0] (0000:00)
PM: Adding info for No Bus:pci0000:00
PM: Adding info for No Bus:0000:00
pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:02.0: PME# disabled
pci 0000:00:04.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:04.0: PME# disabled
pci 0000:00:05.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:05.0: PME# disabled
pci 0000:00:06.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:06.0: PME# disabled
pci 0000:00:07.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:07.0: PME# disabled
pci 0000:00:0a.1: reg 20 io port: [0x5000-0x503f]
pci 0000:00:0a.1: reg 24 io port: [0x5100-0x513f]
pci 0000:00:0a.1: PME# supported from D3hot D3cold
pci 0000:00:0a.1: PME# disabled
pci 0000:00:0b.0: reg 10 32bit mmio: [0xd5006000-0xd5006fff]
pci 0000:00:0b.0: supports D1 D2
pci 0000:00:0b.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:0b.0: PME# disabled
pci 0000:00:0b.1: reg 10 32bit mmio: [0xd5007000-0xd50070ff]
pci 0000:00:0b.1: supports D1 D2
pci 0000:00:0b.1: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:0b.1: PME# disabled
pci 0000:00:0d.0: reg 20 io port: [0xf000-0xf00f]
pci 0000:00:0e.0: reg 10 io port: [0x9f0-0x9f7]
pci 0000:00:0e.0: reg 14 io port: [0xbf0-0xbf3]
pci 0000:00:0e.0: reg 18 io port: [0x970-0x977]
pci 0000:00:0e.0: reg 1c io port: [0xb70-0xb73]
pci 0000:00:0e.0: reg 20 io port: [0xd400-0xd40f]
pci 0000:00:0e.0: reg 24 32bit mmio: [0xd5004000-0xd5004fff]
pci 0000:00:0f.0: reg 10 io port: [0x9e0-0x9e7]
pci 0000:00:0f.0: reg 14 io port: [0xbe0-0xbe3]
pci 0000:00:0f.0: reg 18 io port: [0x960-0x967]
pci 0000:00:0f.0: reg 1c io port: [0xb60-0xb63]
pci 0000:00:0f.0: reg 20 io port: [0xe800-0xe80f]
pci 0000:00:0f.0: reg 24 32bit mmio: [0xd5005000-0xd5005fff]
pci 0000:00:10.1: reg 10 32bit mmio: [0xd5000000-0xd5003fff]
pci 0000:00:10.1: PME# supported from D3hot D3cold
pci 0000:00:10.1: PME# disabled
pci 0000:01:00.0: reg 10 32bit mmio: [0xd0000000-0xd0ffffff]
pci 0000:01:00.0: reg 14 64bit mmio pref: [0xc0000000-0xcfffffff]
pci 0000:01:00.0: reg 1c 64bit mmio: [0xd1000000-0xd1ffffff]
pci 0000:01:00.0: reg 24 io port: [0xa000-0xa07f]
pci 0000:01:00.0: reg 30 32bit mmio pref: [0xd2000000-0xd201ffff]
pci 0000:00:02.0: bridge io port: [0xa000-0xafff]
pci 0000:00:02.0: bridge 32bit mmio: [0xd0000000-0xd2ffffff]
pci 0000:00:02.0: bridge 64bit mmio pref: [0xc0000000-0xcfffffff]
pci 0000:06:06.0: reg 10 32bit mmio: [0xd4001000-0xd40017ff]
pci 0000:06:06.0: reg 14 io port: [0xb000-0xb07f]
pci 0000:06:06.0: supports D2
pci 0000:06:06.0: PME# supported from D2 D3hot D3cold
pci 0000:06:06.0: PME# disabled
pci 0000:06:07.0: reg 10 io port: [0xb400-0xb4ff]
pci 0000:06:07.0: reg 14 32bit mmio: [0xd4000000-0xd40000ff]
pci 0000:06:07.0: reg 30 32bit mmio pref: [0xd3000000-0xd301ffff]
pci 0000:06:07.0: supports D1 D2
pci 0000:06:07.0: PME# supported from D1 D2 D3hot D3cold
pci 0000:06:07.0: PME# disabled
pci 0000:00:10.0: transparent bridge
pci 0000:00:10.0: bridge io port: [0xb000-0xbfff]
pci 0000:00:10.0: bridge 32bit mmio: [0xd3000000-0xd4ffffff]
pci_bus 0000:00: on NUMA node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
PM: Adding info for pci:0000:00:00.0
PM: Adding info for pci:0000:00:00.1
PM: Adding info for pci:0000:00:00.2
PM: Adding info for pci:0000:00:00.3
PM: Adding info for pci:0000:00:00.4
PM: Adding info for pci:0000:00:01.0
PM: Adding info for pci:0000:00:01.1
PM: Adding info for pci:0000:00:01.2
PM: Adding info for pci:0000:00:01.3
PM: Adding info for pci:0000:00:01.4
PM: Adding info for pci:0000:00:01.5
PM: Adding info for pci:0000:00:01.6
PM: Adding info for pci:0000:00:02.0
PM: Adding info for pci:0000:00:04.0
PM: Adding info for pci:0000:00:05.0
PM: Adding info for pci:0000:00:06.0
PM: Adding info for pci:0000:00:07.0
PM: Adding info for pci:0000:00:09.0
PM: Adding info for pci:0000:00:0a.0
PM: Adding info for pci:0000:00:0a.1
PM: Adding info for pci:0000:00:0a.2
PM: Adding info for pci:0000:00:0b.0
PM: Adding info for pci:0000:00:0b.1
PM: Adding info for pci:0000:00:0d.0
PM: Adding info for pci:0000:00:0e.0
PM: Adding info for pci:0000:00:0f.0
PM: Adding info for pci:0000:00:10.0
PM: Adding info for pci:0000:00:10.1
PM: Adding info for pci:0000:01:00.0
PM: Adding info for No Bus:0000:01
PM: Adding info for No Bus:0000:02
PM: Adding info for No Bus:0000:03
PM: Adding info for No Bus:0000:04
PM: Adding info for No Bus:0000:05
PM: Adding info for pci:0000:06:06.0
PM: Adding info for pci:0000:06:07.0
PM: Adding info for No Bus:0000:06
ACPI: PCI Interrupt Link [LNK1] (IRQs 5 7 9 *10 11 14 15)
ACPI: PCI Interrupt Link [LNK2] (IRQs *5 7 9 10 11 14 15)
ACPI: PCI Interrupt Link [LNK3] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK4] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK5] (IRQs 5 *7 9 10 11 14 15)
ACPI: PCI Interrupt Link [LNK6] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK7] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK8] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LUBA] (IRQs 5 *7 9 10 11 14 15)
ACPI: PCI Interrupt Link [LUBB] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LMAC] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LACI] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LAZA] (IRQs 5 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [LPMU] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LMCI] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSMB] (IRQs 5 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [LUB2] (IRQs *5 7 9 10 11 14 15)
ACPI: PCI Interrupt Link [LIDE] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSID] (IRQs 5 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [LFID] (IRQs 5 7 9 *10 11 14 15)
ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0
ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0
ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0, disabled.
ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled.
ACPI: PCI Interrupt Link [APC5] (IRQs 16) *0
ACPI: PCI Interrupt Link [APC6] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APC7] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APC8] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APMU] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [AAZA] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0
PM: Adding info for No Bus:vga_arbiter
vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
vgaarb: loaded
PCI: Using ACPI for IRQ routing
PM: Adding info for No Bus:lo
hpet0: at MMIO 0xfeff0000, IRQs 2, 8, 31
hpet0: 3 comparators, 32-bit 25.000000 MHz counter
Switching to clocksource tsc
pnp: PnP ACPI init
PM: Adding info for No Bus:pnp0
ACPI: bus type pnp registered
PM: Adding info for pnp:00:00
PM: Adding info for pnp:00:01
PM: Adding info for pnp:00:02
PM: Adding info for pnp:00:03
PM: Adding info for pnp:00:04
PM: Adding info for pnp:00:05
PM: Adding info for pnp:00:06
PM: Adding info for pnp:00:07
PM: Adding info for pnp:00:08
PM: Adding info for pnp:00:09
pnp: PnP ACPI: found 10 devices
ACPI: ACPI bus type pnp unregistered
PnPBIOS: Disabled by ACPI PNP
system 00:01: ioport range 0x4000-0x407f has been reserved
system 00:01: ioport range 0x4080-0x40ff has been reserved
system 00:01: ioport range 0x4400-0x447f has been reserved
system 00:01: ioport range 0x4480-0x44ff has been reserved
system 00:01: ioport range 0x4800-0x487f has been reserved
system 00:01: ioport range 0x4880-0x48ff has been reserved
system 00:02: ioport range 0x4d0-0x4d1 has been reserved
system 00:02: ioport range 0x800-0x87f has been reserved
system 00:02: ioport range 0x290-0x297 has been reserved
system 00:02: ioport range 0x880-0x88f has been reserved
system 00:08: iomem range 0xe0000000-0xefffffff has been reserved
system 00:09: iomem range 0xdbc00-0xdbfff has been reserved
system 00:09: iomem range 0xf0000-0xf7fff could not be reserved
system 00:09: iomem range 0xf8000-0xfbfff could not be reserved
system 00:09: iomem range 0xfc000-0xfffff could not be reserved
system 00:09: iomem range 0xfeff0000-0xfeff00ff has been reserved
system 00:09: iomem range 0x7fef0000-0x7fefffff could not be reserved
system 00:09: iomem range 0xffff0000-0xffffffff has been reserved
system 00:09: iomem range 0x0-0x9ffff could not be reserved
system 00:09: iomem range 0x100000-0x7feeffff could not be reserved
system 00:09: iomem range 0xfec00000-0xfec00fff could not be reserved
system 00:09: iomem range 0xfee00000-0xfee00fff has been reserved
system 00:09: iomem range 0xfeff0000-0xfeff03ff could not be reserved
PM: Adding info for No Bus:mem
PM: Adding info for No Bus:kmem
PM: Adding info for No Bus:null
PM: Adding info for No Bus:port
PM: Adding info for No Bus:zero
PM: Adding info for No Bus:full
PM: Adding info for No Bus:random
PM: Adding info for No Bus:urandom
PM: Adding info for No Bus:kmsg
pci 0000:06:07.0: BAR 6: address space collision on of device [0xd3000000-0xd301ffff]
pci 0000:00:02.0: PCI bridge, secondary bus 0000:01
pci 0000:00:02.0: IO window: 0xa000-0xafff
pci 0000:00:02.0: MEM window: 0xd0000000-0xd2ffffff
pci 0000:00:02.0: PREFETCH window: 0x000000c0000000-0x000000cfffffff
pci 0000:00:04.0: PCI bridge, secondary bus 0000:02
pci 0000:00:04.0: IO window: disabled
pci 0000:00:04.0: MEM window: disabled
pci 0000:00:04.0: PREFETCH window: disabled
pci 0000:00:05.0: PCI bridge, secondary bus 0000:03
pci 0000:00:05.0: IO window: disabled
pci 0000:00:05.0: MEM window: disabled
pci 0000:00:05.0: PREFETCH window: disabled
pci 0000:00:06.0: PCI bridge, secondary bus 0000:04
pci 0000:00:06.0: IO window: disabled
pci 0000:00:06.0: MEM window: disabled
pci 0000:00:06.0: PREFETCH window: disabled
pci 0000:00:07.0: PCI bridge, secondary bus 0000:05
pci 0000:00:07.0: IO window: disabled
pci 0000:00:07.0: MEM window: disabled
pci 0000:00:07.0: PREFETCH window: disabled
pci 0000:00:10.0: PCI bridge, secondary bus 0000:06
pci 0000:00:10.0: IO window: 0xb000-0xbfff
pci 0000:00:10.0: MEM window: 0xd3000000-0xd4ffffff
pci 0000:00:10.0: PREFETCH window: 0x80000000-0x800fffff
pci 0000:00:02.0: setting latency timer to 64
pci 0000:00:04.0: setting latency timer to 64
pci 0000:00:05.0: setting latency timer to 64
pci 0000:00:06.0: setting latency timer to 64
pci 0000:00:07.0: setting latency timer to 64
pci 0000:00:10.0: setting latency timer to 64
pci_bus 0000:00: resource 0 io: [0x00-0xffff]
pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
pci_bus 0000:01: resource 0 io: [0xa000-0xafff]
pci_bus 0000:01: resource 1 mem: [0xd0000000-0xd2ffffff]
pci_bus 0000:01: resource 2 pref mem [0xc0000000-0xcfffffff]
pci_bus 0000:06: resource 0 io: [0xb000-0xbfff]
pci_bus 0000:06: resource 1 mem: [0xd3000000-0xd4ffffff]
pci_bus 0000:06: resource 2 pref mem [0x80000000-0x800fffff]
pci_bus 0000:06: resource 3 io: [0x00-0xffff]
pci_bus 0000:06: resource 4 mem: [0x000000-0xffffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
pci 0000:01:00.0: Boot video device
Trying to unpack rootfs image as initramfs...
Freeing initrd memory: 20742k freed
PM: Adding info for No Bus:mcelog
PM: Adding info for No Bus:msr0
PM: Adding info for No Bus:msr1
PM: Adding info for platform:pcspkr
PM: Adding info for No Bus:snapshot
highmem bounce pool size: 64 pages
ROMFS MTD (C) 2007 Red Hat, Inc.
msgmni has been set to 1733
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
pcieport 0000:00:02.0: setting latency timer to 64
PM: Adding info for pci_express:0000:00:02.0:pcie08
pcieport 0000:00:04.0: setting latency timer to 64
PM: Adding info for pci_express:0000:00:04.0:pcie08
pcieport 0000:00:05.0: setting latency timer to 64
PM: Adding info for pci_express:0000:00:05.0:pcie08
pcieport 0000:00:06.0: setting latency timer to 64
PM: Adding info for pci_express:0000:00:06.0:pcie08
pcieport 0000:00:07.0: setting latency timer to 64
PM: Adding info for pci_express:0000:00:07.0:pcie08
PM: Adding info for No Bus:pnp1
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
PM: Adding info for No Bus:tty
PM: Adding info for No Bus:console
PM: Adding info for No Bus:tty0
PM: Adding info for No Bus:vcs
PM: Adding info for No Bus:vcsa
PM: Adding info for No Bus:vcs1
PM: Adding info for No Bus:vcsa1
PM: Adding info for No Bus:tty1
PM: Adding info for No Bus:tty2
PM: Adding info for No Bus:tty3
PM: Adding info for No Bus:tty4
PM: Adding info for No Bus:tty5
PM: Adding info for No Bus:tty6
PM: Adding info for No Bus:tty7
PM: Adding info for No Bus:tty8
PM: Adding info for No Bus:tty9
PM: Adding info for No Bus:tty10
PM: Adding info for No Bus:tty11
PM: Adding info for No Bus:tty12
PM: Adding info for No Bus:tty13
PM: Adding info for No Bus:tty14
PM: Adding info for No Bus:tty15
PM: Adding info for No Bus:tty16
PM: Adding info for No Bus:tty17
PM: Adding info for No Bus:tty18
PM: Adding info for No Bus:tty19
PM: Adding info for No Bus:tty20
PM: Adding info for No Bus:tty21
PM: Adding info for No Bus:tty22
PM: Adding info for No Bus:tty23
PM: Adding info for No Bus:tty24
PM: Adding info for No Bus:tty25
PM: Adding info for No Bus:tty26
PM: Adding info for No Bus:tty27
PM: Adding info for No Bus:tty28
PM: Adding info for No Bus:tty29
PM: Adding info for No Bus:tty30
PM: Adding info for No Bus:tty31
PM: Adding info for No Bus:tty32
PM: Adding info for No Bus:tty33
PM: Adding info for No Bus:tty34
PM: Adding info for No Bus:tty35
PM: Adding info for No Bus:tty36
PM: Adding info for No Bus:tty37
PM: Adding info for No Bus:tty38
PM: Adding info for No Bus:tty39
PM: Adding info for No Bus:tty40
PM: Adding info for No Bus:tty41
PM: Adding info for No Bus:tty42
PM: Adding info for No Bus:tty43
PM: Adding info for No Bus:tty44
PM: Adding info for No Bus:tty45
PM: Adding info for No Bus:tty46
PM: Adding info for No Bus:tty47
PM: Adding info for No Bus:tty48
PM: Adding info for No Bus:tty49
PM: Adding info for No Bus:tty50
PM: Adding info for No Bus:tty51
PM: Adding info for No Bus:tty52
PM: Adding info for No Bus:tty53
PM: Adding info for No Bus:tty54
PM: Adding info for No Bus:tty55
PM: Adding info for No Bus:tty56
PM: Adding info for No Bus:tty57
PM: Adding info for No Bus:tty58
PM: Adding info for No Bus:tty59
PM: Adding info for No Bus:tty60
PM: Adding info for No Bus:tty61
PM: Adding info for No Bus:tty62
PM: Adding info for No Bus:tty63
PM: Adding info for No Bus:ptmx
PM: Adding info for No Bus:hpet
PM: Adding info for No Bus:isa
PM: Adding info for No Bus:ram0
PM: Adding info for No Bus:1:0
PM: Adding info for No Bus:ram1
PM: Adding info for No Bus:1:1
PM: Adding info for No Bus:ram2
PM: Adding info for No Bus:1:2
PM: Adding info for No Bus:ram3
PM: Adding info for No Bus:1:3
PM: Adding info for No Bus:ram4
PM: Adding info for No Bus:1:4
PM: Adding info for No Bus:ram5
PM: Adding info for No Bus:1:5
PM: Adding info for No Bus:ram6
PM: Adding info for No Bus:1:6
PM: Adding info for No Bus:ram7
PM: Adding info for No Bus:1:7
PM: Adding info for No Bus:ram8
PM: Adding info for No Bus:1:8
PM: Adding info for No Bus:ram9
PM: Adding info for No Bus:1:9
PM: Adding info for No Bus:ram10
PM: Adding info for No Bus:1:10
PM: Adding info for No Bus:ram11
PM: Adding info for No Bus:1:11
PM: Adding info for No Bus:ram12
PM: Adding info for No Bus:1:12
PM: Adding info for No Bus:ram13
PM: Adding info for No Bus:1:13
PM: Adding info for No Bus:ram14
PM: Adding info for No Bus:1:14
PM: Adding info for No Bus:ram15
PM: Adding info for No Bus:1:15
brd: module loaded
PNP: No PS/2 controller found. Probing ports directly.
PM: Adding info for platform:i8042
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
PM: Adding info for serio:serio0
PM: Adding info for serio:serio1
PM: Adding info for No Bus:mice
PM: Adding info for No Bus:psaux
mice: PS/2 mouse device common for all mice
PM: Adding info for platform:eisa.0
EISA: Probing bus 0 at eisa.0
PM: Removing info for platform:eisa.0
cpuidle: using governor ladder
TCP cubic registered
Using IPI No-Shortcut mode
PM: Adding info for No Bus:cpu_dma_latency
PM: Adding info for No Bus:network_latency
PM: Adding info for No Bus:network_throughput
PM: Checking image partition /dev/hda6
PM: Resume from disk failed.
Magic number: 14:890:628
Freeing unused kernel memory: 404k freed
NET: Registered protocol family 1
PM: Adding info for No Bus:cooling_device0
fan PNP0C0B:00: registered as cooling_device0
ACPI: Fan [FAN] (on)
PM: Adding info for No Bus:thermal_zone0
thermal LNXTHERM:01: registered as thermal_zone0
ACPI: Thermal Zone [THRM] (40 C)
Uniform Multi-Platform E-IDE driver
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
amd74xx 0000:00:0d.0: UDMA133 controller
amd74xx 0000:00:0d.0: IDE controller (0x10de:0x0265 rev 0xa1)
amd74xx 0000:00:0d.0: IDE port disabled
amd74xx 0000:00:0d.0: BIOS didn't set cable bits correctly. Enabling workaround.
amd74xx 0000:00:0d.0: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xf008-0xf00f
Probing IDE interface ide0...
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_hcd: block sizes: qh 60 qtd 96 itd 160 sitd 96
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci_hcd: block sizes: ed 64 td 64
r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17
r8169 0000:06:07.0: PCI INT A -> Link[APC2] -> GSI 17 (level, low) -> IRQ 17
r8169 0000:06:07.0: no PCI Express capability
PM: Adding info for No Bus:eth0
eth0: RTL8169sb/8110sb at 0xf8b0a000, 00:14:d1:1a:ac:15, XID 10000000 IRQ 17
udev: renamed network interface eth0 to eth1
ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16
ohci1394 0000:06:06.0: PCI INT A -> Link[APC1] -> GSI 16 (level, low) -> IRQ 16
PM: Adding info for ieee1394:fw-host0
PM: Adding info for No Bus:fw-host0
libata version 3.00 loaded.
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[16] MMIO=[d4001000-d40017ff] Max Packet=[2] IR/IT contexts=[4/8]
ohci1394: fw-host0: Serial EEPROM has suspicious values, attempting to set max_packet_size to 512 bytes
hda: PIONEER DVD-RW DVR-111D, ATAPI CD/DVD-ROM drive
PM: Adding info for No Bus:ide0
PM: Adding info for No Bus:ide0
hda: host max PIO5 wanted PIO255(auto-tune) selected PIO4
hda: UDMA/66 mode selected
ide0 at 0x170-0x177,0x376 on irq 15
PM: Adding info for ide:0.0
ACPI: PCI Interrupt Link [APCL] enabled at IRQ 23
ehci_hcd 0000:00:0b.1: PCI INT B -> Link[APCL] -> GSI 23 (level, low) -> IRQ 23
ehci_hcd 0000:00:0b.1: setting latency timer to 64
ehci_hcd 0000:00:0b.1: EHCI Host Controller
drivers/usb/core/inode.c: creating file 'devices'
drivers/usb/core/inode.c: creating file '001'
ehci_hcd 0000:00:0b.1: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:0b.1: reset hcs_params 0x101888 dbg=1 cc=1 pcc=8 !ppc ports=8
ehci_hcd 0000:00:0b.1: reset portroute 0 0 0 0 0 0 0 0
ehci_hcd 0000:00:0b.1: reset hcc_params a086 caching frame 256/512/1024 park
ehci_hcd 0000:00:0b.1: park 0
ehci_hcd 0000:00:0b.1: debug port 1
ehci_hcd 0000:00:0b.1: reset command 080b02 park=3 ithresh=8 period=1024 Reset HALT
ehci_hcd 0000:00:0b.1: cache line size of 32 is not supported
ehci_hcd 0000:00:0b.1: supports USB remote wakeup
ehci_hcd 0000:00:0b.1: irq 23, io mem 0xd5007000
ehci_hcd 0000:00:0b.1: reset command 080b02 park=3 ithresh=8 period=1024 Reset HALT
ehci_hcd 0000:00:0b.1: init command 010009 (park)=0 ithresh=1 period=256 RUN
ehci_hcd 0000:00:0b.1: USB 2.0 started, EHCI 1.00
usb usb1: default language 0x0409
usb usb1: udev 1, busnum 1, minor = 0
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.32testing ehci_hcd
usb usb1: SerialNumber: 0000:00:0b.1
PM: Adding info for usb:usb1
usb usb1: uevent
usb usb1: usb_probe_device
usb usb1: configuration #1 chosen from 1 choice
usb usb1: adding 1-0:1.0 (config #1, interface 0)
PM: Adding info for usb:1-0:1.0
usb 1-0:1.0: uevent
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: no power switching (usb 1.0)
hub 1-0:1.0: individual port over-current protection
hub 1-0:1.0: power on to power good time: 20ms
hub 1-0:1.0: local power source is good
hub 1-0:1.0: trying to enable port power on non-switchable hub
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev1.1
drivers/usb/core/inode.c: creating file '001'
PM: Adding info for No Bus:ep_00
ACPI: PCI Interrupt Link [APCF] enabled at IRQ 22
ohci_hcd 0000:00:0b.0: PCI INT A -> Link[APCF] -> GSI 22 (level, low) -> IRQ 22
ohci_hcd 0000:00:0b.0: setting latency timer to 64
ohci_hcd 0000:00:0b.0: OHCI Host Controller
drivers/usb/core/inode.c: creating file '002'
ohci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:0b.0: created debug files
ohci_hcd 0000:00:0b.0: supports USB remote wakeup
ohci_hcd 0000:00:0b.0: irq 22, io mem 0xd5006000
usb usb1: uevent
usb usb1: uevent
PM: Adding info for ieee1394:001106000000bd66
PM: Adding info for No Bus:001106000000bd66
ieee1394: Host added: ID:BUS[0-00:1023] GUID[001106000000bd66]
PM: Adding info for ieee1394:001a66fffee31809
PM: Adding info for No Bus:001a66fffee31809
ieee1394: Node added: ID:BUS[0-01:1023] GUID[001a66fffee31809]
PM: Adding info for ieee1394:001a66fffee31809-0
PM: Adding info for No Bus:001a66fffee31809-0
PM: Adding info for ieee1394:001a66fffee31809-1
PM: Adding info for No Bus:001a66fffee31809-1
ohci_hcd 0000:00:0b.0: OHCI controller state
ohci_hcd 0000:00:0b.0: OHCI 1.0, NO legacy support registers
ohci_hcd 0000:00:0b.0: control 0x683 RWE RWC HCFS=operational CBSR=3
ohci_hcd 0000:00:0b.0: cmdstatus 0x00000 SOC=0
ohci_hcd 0000:00:0b.0: intrstatus 0x00000004 SF
ohci_hcd 0000:00:0b.0: intrenable 0x8000004a MIE RHSC RD WDH
ohci_hcd 0000:00:0b.0: hcca frame #0003
ohci_hcd 0000:00:0b.0: roothub.a 01000208 POTPGT=1 NPS NDP=8(8)
ohci_hcd 0000:00:0b.0: roothub.b 00000000 PPCM=0000 DR=0000
ohci_hcd 0000:00:0b.0: roothub.status 00008000 DRWE
ohci_hcd 0000:00:0b.0: roothub.portstatus [0] 0x00000100 PPS
ohci_hcd 0000:00:0b.0: roothub.portstatus [1] 0x00000100 PPS
ohci_hcd 0000:00:0b.0: roothub.portstatus [2] 0x00000100 PPS
ohci_hcd 0000:00:0b.0: roothub.portstatus [3] 0x00000100 PPS
ohci_hcd 0000:00:0b.0: roothub.portstatus [4] 0x00000100 PPS
ohci_hcd 0000:00:0b.0: roothub.portstatus [5] 0x00000100 PPS
ohci_hcd 0000:00:0b.0: roothub.portstatus [6] 0x00000100 PPS
ohci_hcd 0000:00:0b.0: roothub.portstatus [7] 0x00000100 PPS
usb usb2: default language 0x0409
usb usb2: udev 1, busnum 2, minor = 128
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: OHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.32testing ohci_hcd
usb usb2: SerialNumber: 0000:00:0b.0
PM: Adding info for usb:usb2
usb usb2: uevent
usb usb2: usb_probe_device
usb usb2: configuration #1 chosen from 1 choice
usb usb2: adding 2-0:1.0 (config #1, interface 0)
PM: Adding info for usb:2-0:1.0
usb 2-0:1.0: uevent
hub 2-0:1.0: usb_probe_interface
hub 2-0:1.0: usb_probe_interface - got id
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 8 ports detected
hub 2-0:1.0: standalone hub
hub 2-0:1.0: no power switching (usb 1.0)
hub 2-0:1.0: global over-current protection
hub 2-0:1.0: power on to power good time: 2ms
hub 2-0:1.0: local power source is good
hub 2-0:1.0: no over-current condition exists
hub 2-0:1.0: trying to enable port power on non-switchable hub
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev2.1
drivers/usb/core/inode.c: creating file '001'
PM: Adding info for No Bus:ep_00
sata_nv 0000:00:0e.0: version 3.5
ACPI: PCI Interrupt Link [APSI] enabled at IRQ 21
sata_nv 0000:00:0e.0: PCI INT A -> Link[APSI] -> GSI 21 (level, low) -> IRQ 21
sata_nv 0000:00:0e.0: Using SWNCQ mode
sata_nv 0000:00:0e.0: setting latency timer to 64
scsi0 : sata_nv
PM: Adding info for scsi:host0
PM: Adding info for No Bus:host0
scsi1 : sata_nv
PM: Adding info for scsi:host1
PM: Adding info for No Bus:host1
ata1: SATA max UDMA/133 cmd 0x9f0 ctl 0xbf0 bmdma 0xd400 irq 21
ata2: SATA max UDMA/133 cmd 0x970 ctl 0xb70 bmdma 0xd408 irq 21
usb usb2: uevent
ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 20
sata_nv 0000:00:0f.0: PCI INT A -> Link[APSJ] -> GSI 20 (level, low) -> IRQ 20
sata_nv 0000:00:0f.0: Using SWNCQ mode
sata_nv 0000:00:0f.0: setting latency timer to 64
usb usb2: uevent
scsi2 : sata_nv
PM: Adding info for scsi:host2
PM: Adding info for No Bus:host2
scsi3 : sata_nv
PM: Adding info for scsi:host3
PM: Adding info for No Bus:host3
ata3: SATA max UDMA/133 cmd 0x9e0 ctl 0xbe0 bmdma 0xe800 irq 20
ata4: SATA max UDMA/133 cmd 0x960 ctl 0xb60 bmdma 0xe808 irq 20
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 1-0:1.0: port 1: status 0501 change 0001
ehci_hcd 0000:00:0b.1: GetStatus port 2 status 001803 POWER sig=j CSC CONNECT
hub 1-0:1.0: port 2: status 0501 change 0001
ehci_hcd 0000:00:0b.1: GetStatus port 3 status 001803 POWER sig=j CSC CONNECT
hub 1-0:1.0: port 3: status 0501 change 0001
ehci_hcd 0000:00:0b.1: GetStatus port 6 status 001803 POWER sig=j CSC CONNECT
hub 1-0:1.0: port 6: status 0501 change 0001
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0000
hub 1-0:1.0: state 7 ports 8 chg 004e evt 0000
hub 1-0:1.0: port 1, status 0501, change 0000, 480 Mb/s
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 1-0:1.0: port 2, status 0501, change 0000, 480 Mb/s
ehci_hcd 0000:00:0b.1: port 2 high speed
ehci_hcd 0000:00:0b.1: GetStatus port 2 status 001005 POWER sig=se0 PE CONNECT
usb 1-2: new high speed USB device using ehci_hcd and address 3
ata3: SATA link down (SStatus 0 SControl 300)
ehci_hcd 0000:00:0b.1: port 2 high speed
ehci_hcd 0000:00:0b.1: GetStatus port 2 status 001005 POWER sig=se0 PE CONNECT
usb 1-2: default language 0x0409
usb 1-2: udev 3, busnum 1, minor = 2
usb 1-2: New USB device found, idVendor=058f, idProduct=6362
usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-2: Product: Mass Storage Device
usb 1-2: Manufacturer: Generic
usb 1-2: SerialNumber: 058F312D81B
PM: Adding info for usb:1-2
usb 1-2: uevent
usb 1-2: usb_probe_device
usb 1-2: configuration #1 chosen from 1 choice
usb 1-2: adding 1-2:1.0 (config #1, interface 0)
PM: Adding info for usb:1-2:1.0
usb 1-2:1.0: uevent
PM: Adding info for No Bus:ep_01
PM: Adding info for No Bus:ep_82
PM: Adding info for No Bus:usbdev1.3
drivers/usb/core/inode.c: creating file '003'
PM: Adding info for No Bus:ep_00
hub 1-0:1.0: port 3, status 0501, change 0000, 480 Mb/s
usb 1-2: uevent
usb 1-2: uevent
Initializing USB Mass Storage driver...
usb-storage 1-2:1.0: usb_probe_interface
usb-storage 1-2:1.0: usb_probe_interface - got id
scsi4 : SCSI emulation for USB Mass Storage devices
PM: Adding info for scsi:host4
PM: Adding info for No Bus:host4
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: ATA-7: SAMSUNG SP2504C, VT100-41, max UDMA7
ata1.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32)
ehci_hcd 0000:00:0b.1: port 3 high speed
ehci_hcd 0000:00:0b.1: GetStatus port 3 status 001005 POWER sig=se0 PE CONNECT
ata1.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access ATA SAMSUNG SP2504C VT10 PQ: 0 ANSI: 5
PM: Adding info for scsi:target0:0:0
PM: Adding info for scsi:0:0:0:0
PM: Adding info for No Bus:0:0:0:0
PM: Adding info for No Bus:0:0:0:0
usb 1-3: new high speed USB device using ehci_hcd and address 4
ehci_hcd 0000:00:0b.1: port 3 high speed
ehci_hcd 0000:00:0b.1: GetStatus port 3 status 001005 POWER sig=se0 PE CONNECT
usb 1-3: default language 0x0409
usb 1-3: udev 4, busnum 1, minor = 3
usb 1-3: New USB device found, idVendor=05e3, idProduct=0605
usb 1-3: New USB device strings: Mfr=0, Product=1, SerialNumber=0
usb 1-3: Product: USB2.0 Hub
PM: Adding info for usb:1-3
usb 1-3: uevent
usb 1-3: usb_probe_device
usb 1-3: configuration #1 chosen from 1 choice
usb 1-3: adding 1-3:1.0 (config #1, interface 0)
PM: Adding info for usb:1-3:1.0
usb 1-3:1.0: uevent
hub 1-3:1.0: usb_probe_interface
hub 1-3:1.0: usb_probe_interface - got id
hub 1-3:1.0: USB hub found
hub 1-3:1.0: 4 ports detected
hub 1-3:1.0: standalone hub
hub 1-3:1.0: individual port power switching
hub 1-3:1.0: individual port over-current protection
hub 1-3:1.0: Single TT
hub 1-3:1.0: TT requires at most 32 FS bit times (2664 ns)
hub 1-3:1.0: Port indicators are supported
hub 1-3:1.0: power on to power good time: 100ms
usb 1-3: uevent
hub 1-3:1.0: local power source is good
hub 1-3:1.0: enabling power on all ports
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev1.4
drivers/usb/core/inode.c: creating file '004'
PM: Adding info for No Bus:ep_00
hub 1-0:1.0: port 6, status 0501, change 0000, 480 Mb/s
usb 1-3: uevent
ehci_hcd 0000:00:0b.1: port 6 high speed
ehci_hcd 0000:00:0b.1: GetStatus port 6 status 001005 POWER sig=se0 PE CONNECT
hub 1-3:1.0: port 1: status 0101 change 0001
usb 1-6: new high speed USB device using ehci_hcd and address 5
ehci_hcd 0000:00:0b.1: port 6 high speed
ehci_hcd 0000:00:0b.1: GetStatus port 6 status 001005 POWER sig=se0 PE CONNECT
usb 1-3: link qh256-0001/c1c77d40 start 1 [1/0 us]
usb 1-6: udev 5, busnum 1, minor = 4
usb 1-6: New USB device found, idVendor=0409, idProduct=0059
usb 1-6: New USB device strings: Mfr=0, Product=0, SerialNumber=0
PM: Adding info for usb:1-6
usb 1-6: uevent
usb 1-6: usb_probe_device
usb 1-6: configuration #1 chosen from 1 choice
usb 1-6: adding 1-6:1.0 (config #1, interface 0)
PM: Adding info for usb:1-6:1.0
usb 1-6:1.0: uevent
hub 1-6:1.0: usb_probe_interface
hub 1-6:1.0: usb_probe_interface - got id
hub 1-6:1.0: USB hub found
hub 1-6:1.0: 4 ports detected
hub 1-6:1.0: standalone hub
hub 1-6:1.0: individual port power switching
hub 1-6:1.0: individual port over-current protection
hub 1-6:1.0: Single TT
hub 1-6:1.0: TT requires at most 16 FS bit times (1332 ns)
hub 1-6:1.0: Port indicators are supported
hub 1-6:1.0: power on to power good time: 100ms
hub 1-6:1.0: local power source is good
hub 1-6:1.0: enabling power on all ports
usb 1-6: uevent
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev1.5
usb 1-6: uevent
drivers/usb/core/inode.c: creating file '005'
PM: Adding info for No Bus:ep_00
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00010301 CSC LSDA PPS CCS
hub 2-0:1.0: port 1, status 0301, change 0001, 1.5 Mb/s
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
hub 1-6:1.0: port 1: status 0301 change 0001
hub 1-6:1.0: port 3: status 0101 change 0001
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ata2.00: ATA-7: ST3250620AS, 3.AAC, max UDMA/133
ata2.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32)
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130301 PRSC PESC CSC LSDA PPS CCS
hub 2-0:1.0: unable to enumerate USB device on port 1
hub 1-3:1.0: state 7 ports 4 chg 0002 evt 0000
hub 1-3:1.0: port 1, status 0101, change 0000, 12 Mb/s
hub 1-3:1.0: port 1 not reset yet, waiting 10ms
usb 1-6: link qh256-0001/c1c77e40 start 2 [1/0 us]
ata2.00: configured for UDMA/133
scsi 1:0:0:0: Direct-Access ATA ST3250620AS 3.AA PQ: 0 ANSI: 5
PM: Adding info for scsi:target1:0:0
PM: Adding info for scsi:1:0:0:0
PM: Adding info for No Bus:1:0:0:0
PM: Adding info for No Bus:1:0:0:0
usb 1-3.1: new high speed USB device using ehci_hcd and address 6
usb 1-3.1: udev 6, busnum 1, minor = 5
usb 1-3.1: New USB device found, idVendor=0409, idProduct=0059
usb 1-3.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
PM: Adding info for usb:1-3.1
usb 1-3.1: uevent
usb 1-3.1: usb_probe_device
usb 1-3.1: configuration #1 chosen from 1 choice
usb 1-3.1: adding 1-3.1:1.0 (config #1, interface 0)
PM: Adding info for usb:1-3.1:1.0
usb 1-3.1:1.0: uevent
hub 1-3.1:1.0: usb_probe_interface
hub 1-3.1:1.0: usb_probe_interface - got id
hub 1-3.1:1.0: USB hub found
hub 1-3.1:1.0: 4 ports detected
hub 1-3.1:1.0: standalone hub
hub 1-3.1:1.0: individual port power switching
hub 1-3.1:1.0: individual port over-current protection
hub 1-3.1:1.0: Single TT
hub 1-3.1:1.0: TT requires at most 16 FS bit times (1332 ns)
hub 1-3.1:1.0: Port indicators are supported
hub 1-3.1:1.0: power on to power good time: 100ms
hub 1-3.1:1.0: local power source is good
hub 1-3.1:1.0: enabling power on all ports
usb 1-3.1: uevent
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev1.6
drivers/usb/core/inode.c: creating file '006'
PM: Adding info for No Bus:ep_00
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 2-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
usb 1-3.1: uevent
hub 1-3.1:1.0: port 1: status 0301 change 0001
hub 1-3.1:1.0: port 2: status 0101 change 0001
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130301 PRSC PESC CSC LSDA PPS CCS
hub 2-0:1.0: unable to enumerate USB device on port 1
hub 1-6:1.0: state 7 ports 4 chg 000a evt 0000
hub 1-6:1.0: port 1, status 0301, change 0000, 1.5 Mb/s
hub 1-6:1.0: port 1 not reset yet, waiting 10ms
usb 1-3.1: link qh256-0001/c1c77e80 start 3 [1/0 us]
usb 1-6.1: new low speed USB device using ehci_hcd and address 7
hub 1-6:1.0: port 1 not reset yet, waiting 10ms
usb 1-6.1: skipped 1 descriptor after interface
usb 1-6.1: default language 0x0409
usb 1-6.1: udev 7, busnum 1, minor = 6
usb 1-6.1: New USB device found, idVendor=2222, idProduct=3100
usb 1-6.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-6.1: Product: Macally ECOMouse
usb 1-6.1: Manufacturer: Macally Peripherals
PM: Adding info for usb:1-6.1
usb 1-6.1: uevent
usb 1-6.1: usb_probe_device
usb 1-6.1: configuration #1 chosen from 1 choice
usb 1-6.1: adding 1-6.1:1.0 (config #1, interface 0)
PM: Adding info for usb:1-6.1:1.0
usb 1-6.1:1.0: uevent
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev1.7
drivers/usb/core/inode.c: creating file '007'
PM: Adding info for No Bus:ep_00
hub 1-6:1.0: port 3, status 0101, change 0000, 12 Mb/s
usb 1-6.1: uevent
usb 1-6.1: uevent
usbcore: registered new interface driver hiddev
usbhid 1-6.1:1.0: usb_probe_interface
usbhid 1-6.1:1.0: usb_probe_interface - got id
PM: Adding info for hid:0003:2222:3100.0001
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
PM: Adding info for No Bus:input0
input: Macally Peripherals Macally ECOMouse as /devices/pci0000:00/0000:00:0b.1/usb1/1-6/1-6.1/1-6.1:1.0/input/input0
PM: Adding info for No Bus:mouse0
generic-usb 0003:2222:3100.0001: input: USB HID v1.00 Mouse [Macally Peripherals Macally ECOMouse ] on usb-0000:00:0b.1-6.1/input0
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
hub 1-6:1.0: port 3 not reset yet, waiting 10ms
ata4.00: ATAPI: ATAPI iHOS104, WL08, max UDMA/100
ata4.00: configured for UDMA/100
usb 1-6.3: new full speed USB device using ehci_hcd and address 8
hub 1-6:1.0: port 3 not reset yet, waiting 10ms
usb 1-6.3: ep0 maxpacket = 8
usb 1-6.3: default language 0x0409
usb 1-6.3: udev 8, busnum 1, minor = 7
usb 1-6.3: New USB device found, idVendor=05e3, idProduct=0604
usb 1-6.3: New USB device strings: Mfr=0, Product=1, SerialNumber=0
usb 1-6.3: Product: USB Hub
PM: Adding info for usb:1-6.3
usb 1-6.3: uevent
usb 1-6.3: usb_probe_device
usb 1-6.3: configuration #1 chosen from 1 choice
usb 1-6.3: adding 1-6.3:1.0 (config #1, interface 0)
PM: Adding info for usb:1-6.3:1.0
usb 1-6.3:1.0: uevent
hub 1-6.3:1.0: usb_probe_interface
hub 1-6.3:1.0: usb_probe_interface - got id
hub 1-6.3:1.0: USB hub found
usb 1-6.3: uevent
hub 1-6.3:1.0: 4 ports detected
hub 1-6.3:1.0: standalone hub
hub 1-6.3:1.0: individual port power switching
hub 1-6.3:1.0: individual port over-current protection
hub 1-6.3:1.0: power on to power good time: 100ms
hub 1-6.3:1.0: local power source is good
hub 1-6.3:1.0: enabling power on all ports
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev1.8
drivers/usb/core/inode.c: creating file '008'
PM: Adding info for No Bus:ep_00
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 2-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
usb 1-6.3: uevent
hub 1-6.3:1.0: port 3: status 0301 change 0001
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130301 PRSC PESC CSC LSDA PPS CCS
hub 2-0:1.0: unable to enumerate USB device on port 1
hub 1-3.1:1.0: state 7 ports 4 chg 0006 evt 0000
hub 1-3.1:1.0: port 1, status 0301, change 0000, 1.5 Mb/s
hub 1-3.1:1.0: port 1 not reset yet, waiting 10ms
usb 1-6.3: link qh128-0e01/c1c66400 start 4 [1/2 us]
usb 1-3.1.1: new low speed USB device using ehci_hcd and address 9
hub 1-3.1:1.0: port 1 not reset yet, waiting 10ms
usb 1-3.1.1: skipped 1 descriptor after interface
usb 1-3.1.1: skipped 1 descriptor after interface
usb 1-3.1.1: default language 0x0409
usb 1-3.1.1: udev 9, busnum 1, minor = 8
usb 1-3.1.1: New USB device found, idVendor=10d5, idProduct=0004
usb 1-3.1.1: New USB device strings: Mfr=0, Product=2, SerialNumber=0
usb 1-3.1.1: Product: PS2 to USB AdapterA3
PM: Adding info for usb:1-3.1.1
usb 1-3.1.1: uevent
usb 1-3.1.1: usb_probe_device
usb 1-3.1.1: configuration #1 chosen from 1 choice
usb 1-3.1.1: uevent
usb 1-3.1.1: adding 1-3.1.1:1.0 (config #1, interface 0)
PM: Adding info for usb:1-3.1.1:1.0
usb 1-3.1.1:1.0: uevent
usbhid 1-3.1.1:1.0: usb_probe_interface
usbhid 1-3.1.1:1.0: usb_probe_interface - got id
PM: Adding info for hid:0003:10D5:0004.0002
PM: Adding info for No Bus:input1
input: PS2 to USB AdapterA3 as /devices/pci0000:00/0000:00:0b.1/usb1/1-3/1-3.1/1-3.1.1/1-3.1.1:1.0/input/input1
usb 1-3.1.1: link qh8-0e01/c1c66700 start 5 [1/2 us]
generic-usb 0003:10D5:0004.0002: input: USB HID v1.10 Keyboard [PS2 to USB AdapterA3] on usb-0000:00:0b.1-3.1.1/input0
PM: Adding info for No Bus:ep_81
usb 1-3.1.1: adding 1-3.1.1:1.1 (config #1, interface 1)
PM: Adding info for usb:1-3.1.1:1.1
usb 1-3.1.1:1.1: uevent
usbhid 1-3.1.1:1.1: usb_probe_interface
usbhid 1-3.1.1:1.1: usb_probe_interface - got id
PM: Adding info for hid:0003:10D5:0004.0003
PM: Adding info for No Bus:input2
input: PS2 to USB AdapterA3 as /devices/pci0000:00/0000:00:0b.1/usb1/1-3/1-3.1/1-3.1.1/1-3.1.1:1.1/input/input2
usb 1-3.1.1: link qh8-0e01/c1c667c0 start 6 [1/2 us]
PM: Adding info for No Bus:mouse1
generic-usb 0003:10D5:0004.0003: input: USB HID v1.10 Mouse [PS2 to USB AdapterA3] on usb-0000:00:0b.1-3.1.1/input1
PM: Adding info for No Bus:ep_82
PM: Adding info for No Bus:usbdev1.9
drivers/usb/core/inode.c: creating file '009'
PM: Adding info for No Bus:ep_00
usb 1-3.1.1: uevent
hub 1-3.1:1.0: port 2, status 0101, change 0000, 12 Mb/s
hub 1-3.1:1.0: port 2 not reset yet, waiting 10ms
usb 1-3.1.2: new high speed USB device using ehci_hcd and address 10
hub 1-3.1:1.0: port 2 not reset yet, waiting 10ms
usb 1-3.1.2: default language 0x0409
usb 1-3.1.2: udev 10, busnum 1, minor = 9
usb 1-3.1.2: New USB device found, idVendor=05e3, idProduct=0605
usb 1-3.1.2: New USB device strings: Mfr=0, Product=1, SerialNumber=0
usb 1-3.1.2: Product: USB2.0 Hub
PM: Adding info for usb:1-3.1.2
usb 1-3.1.2: uevent
usb 1-3.1.2: usb_probe_device
usb 1-3.1.2: configuration #1 chosen from 1 choice
usb 1-3.1.2: adding 1-3.1.2:1.0 (config #1, interface 0)
PM: Adding info for usb:1-3.1.2:1.0
usb 1-3.1.2:1.0: uevent
hub 1-3.1.2:1.0: usb_probe_interface
hub 1-3.1.2:1.0: usb_probe_interface - got id
hub 1-3.1.2:1.0: USB hub found
hub 1-3.1.2:1.0: 4 ports detected
hub 1-3.1.2:1.0: standalone hub
hub 1-3.1.2:1.0: individual port power switching
hub 1-3.1.2:1.0: individual port over-current protection
hub 1-3.1.2:1.0: Single TT
hub 1-3.1.2:1.0: TT requires at most 32 FS bit times (2664 ns)
hub 1-3.1.2:1.0: Port indicators are supported
hub 1-3.1.2:1.0: power on to power good time: 100ms
usb 1-3.1.2: uevent
hub 1-3.1.2:1.0: local power source is good
hub 1-3.1.2:1.0: enabling power on all ports
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev1.10
drivers/usb/core/inode.c: creating file '010'
PM: Adding info for No Bus:ep_00
hub 1-6:1.0: state 7 ports 4 chg 0000 evt 0002
usb 1-3.1.2: uevent
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 2-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 1-3.1.2:1.0: port 1: status 0101 change 0001
hub 1-3.1.2:1.0: port 2: status 0301 change 0001
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 2-0:1.0: unable to enumerate USB device on port 1
hub 1-6.3:1.0: state 7 ports 4 chg 0008 evt 0000
hub 1-6.3:1.0: port 3, status 0301, change 0000, 1.5 Mb/s
usb 1-3.1.2: link qh256-0001/c1c66900 start 7 [1/0 us]
usb 1-6.3.3: new low speed USB device using ehci_hcd and address 11
usb 1-6.3.3: skipped 1 descriptor after interface
usb 1-6.3.3: skipped 1 descriptor after interface
usb 1-6.3.3: default language 0x0409
usb 1-6.3.3: udev 11, busnum 1, minor = 10
usb 1-6.3.3: New USB device found, idVendor=2222, idProduct=0013
usb 1-6.3.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-6.3.3: Product: Macally iKeySlim
usb 1-6.3.3: Manufacturer: Macally Peripherals
PM: Adding info for usb:1-6.3.3
usb 1-6.3.3: uevent
usb 1-6.3.3: usb_probe_device
usb 1-6.3.3: configuration #1 chosen from 1 choice
usb 1-6.3.3: uevent
usb 1-6.3.3: adding 1-6.3.3:1.0 (config #1, interface 0)
PM: Adding info for usb:1-6.3.3:1.0
usb 1-6.3.3:1.0: uevent
usbhid 1-6.3.3:1.0: usb_probe_interface
usbhid 1-6.3.3:1.0: usb_probe_interface - got id
PM: Adding info for hid:0003:2222:0013.0004
PM: Adding info for No Bus:input3
input: Macally Peripherals Macally iKeySlim as /devices/pci0000:00/0000:00:0b.1/usb1/1-6/1-6.3/1-6.3.3/1-6.3.3:1.0/input/input3
usb 1-6.3.3: link qh8-0e01/c1c66c00 start 0 [1/2 us]
generic-usb 0003:2222:0013.0004: input: USB HID v1.10 Keyboard [Macally Peripherals Macally iKeySlim] on usb-0000:00:0b.1-6.3.3/input0
PM: Adding info for No Bus:ep_81
usb 1-6.3.3: adding 1-6.3.3:1.1 (config #1, interface 1)
PM: Adding info for usb:1-6.3.3:1.1
usb 1-6.3.3:1.1: uevent
usbhid 1-6.3.3:1.1: usb_probe_interface
usbhid 1-6.3.3:1.1: usb_probe_interface - got id
PM: Adding info for hid:0003:2222:0013.0005
PM: Adding info for No Bus:input4
input: Macally Peripherals Macally iKeySlim as /devices/pci0000:00/0000:00:0b.1/usb1/1-6/1-6.3/1-6.3.3/1-6.3.3:1.1/input/input4
usb 1-6.3.3: link qh8-0e01/c1c66d40 start 1 [1/2 us]
PM: Adding info for No Bus:mouse2
generic-usb 0003:2222:0013.0005: input: USB HID v1.10 Mouse [Macally Peripherals Macally iKeySlim] on usb-0000:00:0b.1-6.3.3/input1
PM: Adding info for No Bus:ep_82
PM: Adding info for No Bus:usbdev1.11
drivers/usb/core/inode.c: creating file '011'
PM: Adding info for No Bus:ep_00
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030300 PESC CSC LSDA PPS
hub 2-0:1.0: port 1, status 0300, change 0003, 1.5 Mb/s
usb 1-6.3.3: uevent
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x300
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 1-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 1-6.3:1.0: state 7 ports 4 chg 0000 evt 0008
hub 1-3.1.2:1.0: state 7 ports 4 chg 0006 evt 0000
hub 1-3.1.2:1.0: port 1, status 0101, change 0000, 12 Mb/s
hub 1-3.1.2:1.0: port 1 not reset yet, waiting 10ms
usb 1-3.1.2.1: new high speed USB device using ehci_hcd and address 13
hub 1-3.1.2:1.0: port 1 not reset yet, waiting 10ms
usb 1-3.1.2.1: default language 0x0409
usb 1-3.1.2.1: udev 13, busnum 1, minor = 12
usb 1-3.1.2.1: New USB device found, idVendor=090c, idProduct=1000
usb 1-3.1.2.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-3.1.2.1: Product: DISK 2.0
usb 1-3.1.2.1: Manufacturer: USB
usb 1-3.1.2.1: SerialNumber: PHN84K6AD8PLXSVC
PM: Adding info for usb:1-3.1.2.1
usb 1-3.1.2.1: uevent
usb 1-3.1.2.1: usb_probe_device
usb 1-3.1.2.1: configuration #1 chosen from 1 choice
usb 1-3.1.2.1: adding 1-3.1.2.1:1.0 (config #1, interface 0)
PM: Adding info for usb:1-3.1.2.1:1.0
usb 1-3.1.2.1:1.0: uevent
usb-storage 1-3.1.2.1:1.0: usb_probe_interface
usb-storage 1-3.1.2.1:1.0: usb_probe_interface - got id
scsi5 : SCSI emulation for USB Mass Storage devices
PM: Adding info for scsi:host5
PM: Adding info for No Bus:host5
usb-storage: device found at 13
usb-storage: waiting for device to settle before scanning
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:ep_02
PM: Adding info for No Bus:usbdev1.13
drivers/usb/core/inode.c: creating file '013'
PM: Adding info for No Bus:ep_00
usb 1-3.1.2.1: uevent
hub 1-3.1.2:1.0: port 2, status 0301, change 0000, 1.5 Mb/s
usb 1-3.1.2.1: uevent
usb 1-3.1.2.2: new low speed USB device using ehci_hcd and address 14
usb 1-3.1.2.2: skipped 1 descriptor after interface
usb 1-3.1.2.2: default language 0x0409
usb 1-3.1.2.2: udev 14, busnum 1, minor = 13
usb 1-3.1.2.2: New USB device found, idVendor=046d, idProduct=c00c
usb 1-3.1.2.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-3.1.2.2: Product: USB Optical Mouse
usb 1-3.1.2.2: Manufacturer: Logitech
PM: Adding info for usb:1-3.1.2.2
usb 1-3.1.2.2: uevent
usb 1-3.1.2.2: usb_probe_device
usb 1-3.1.2.2: configuration #1 chosen from 1 choice
usb 1-3.1.2.2: adding 1-3.1.2.2:1.0 (config #1, interface 0)
PM: Adding info for usb:1-3.1.2.2:1.0
usb 1-3.1.2.2:1.0: uevent
usbhid 1-3.1.2.2:1.0: usb_probe_interface
usbhid 1-3.1.2.2:1.0: usb_probe_interface - got id
PM: Adding info for hid:0003:046D:C00C.0006
usb 1-3.1.2.2: uevent
PM: Adding info for No Bus:input5
input: Logitech USB Optical Mouse as /devices/pci0000:00/0000:00:0b.1/usb1/1-3/1-3.1/1-3.1.2/1-3.1.2.2/1-3.1.2.2:1.0/input/input5
PM: Adding info for No Bus:mouse3
generic-usb 0003:046D:C00C.0006: input: USB HID v1.10 Mouse [Logitech USB Optical Mouse] on usb-0000:00:0b.1-3.1.2.2/input0
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev1.14
drivers/usb/core/inode.c: creating file '014'
PM: Adding info for No Bus:ep_00
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00010301 CSC LSDA PPS CCS
hub 2-0:1.0: port 1, status 0301, change 0001, 1.5 Mb/s
usb 1-3.1.2.2: uevent
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 2-0:1.0: unable to enumerate USB device on port 1
hub 1-3.1.2:1.0: state 7 ports 4 chg 0000 evt 0004
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030300 PESC CSC LSDA PPS
hub 2-0:1.0: port 1, status 0300, change 0003, 1.5 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x300
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 1-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00010301 CSC LSDA PPS CCS
hub 2-0:1.0: port 1, status 0301, change 0001, 1.5 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 2-0:1.0: unable to enumerate USB device on port 1
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 1-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 2-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 2-0:1.0: unable to enumerate USB device on port 1
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 1-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 2-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 2-0:1.0: unable to enumerate USB device on port 1
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 1-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 2-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 2-0:1.0: unable to enumerate USB device on port 1
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 1-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 2-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 2-0:1.0: unable to enumerate USB device on port 1
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 1-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 2-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 2-0:1.0: unable to enumerate USB device on port 1
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 1-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
scsi 4:0:0:0: Direct-Access Generic USB SD Reader 1.00 PQ: 0 ANSI: 0
PM: Adding info for scsi:target4:0:0
PM: Adding info for scsi:4:0:0:0
PM: Adding info for No Bus:4:0:0:0
PM: Adding info for No Bus:4:0:0:0
scsi 4:0:0:1: Direct-Access Generic USB CF Reader 1.01 PQ: 0 ANSI: 0
PM: Adding info for scsi:4:0:0:1
PM: Adding info for No Bus:4:0:0:1
PM: Adding info for No Bus:4:0:0:1
scsi 4:0:0:2: Direct-Access Generic USB SM Reader 1.02 PQ: 0 ANSI: 0
PM: Adding info for scsi:4:0:0:2
PM: Adding info for No Bus:4:0:0:2
PM: Adding info for No Bus:4:0:0:2
scsi 4:0:0:3: Direct-Access Generic USB MS Reader 1.03 PQ: 0 ANSI: 0
PM: Adding info for scsi:4:0:0:3
PM: Adding info for No Bus:4:0:0:3
PM: Adding info for No Bus:4:0:0:3
usb-storage: device scan complete
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 2-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 2-0:1.0: unable to enumerate USB device on port 1
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 1-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 2-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 2-0:1.0: unable to enumerate USB device on port 1
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 1-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 2-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 2-0:1.0: unable to enumerate USB device on port 1
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 1-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 2-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 2-0:1.0: unable to enumerate USB device on port 1
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 1-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 2-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 2-0:1.0: unable to enumerate USB device on port 1
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 1-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 2-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 2-0:1.0: unable to enumerate USB device on port 1
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 1-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 2-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 2-0:1.0: unable to enumerate USB device on port 1
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 1-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 2-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 2-0:1.0: unable to enumerate USB device on port 1
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 1-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
scsi 5:0:0:0: Direct-Access USB DISK 2.0 0403 PQ: 0 ANSI: 0 CCS
PM: Adding info for scsi:target5:0:0
PM: Adding info for scsi:5:0:0:0
PM: Adding info for No Bus:5:0:0:0
PM: Adding info for No Bus:5:0:0:0
usb-storage: device scan complete
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 2-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 2-0:1.0: unable to enumerate USB device on port 1
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 1-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 2-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 2-0:1.0: unable to enumerate USB device on port 1
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 1-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 2-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 2-0:1.0: unable to enumerate USB device on port 1
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 1-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 2-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 2-0:1.0: unable to enumerate USB device on port 1
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 1-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 2-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 2-0:1.0: unable to enumerate USB device on port 1
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 1-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 2-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 2-0:1.0: unable to enumerate USB device on port 1
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 1-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 2-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 2-0:1.0: unable to enumerate USB device on port 1
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 1-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 2-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 2-0:1.0: unable to enumerate USB device on port 1
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 1-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 2-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 2-0:1.0: unable to enumerate USB device on port 1
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 1-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 2-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 2-0:1.0: unable to enumerate USB device on port 1
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 1-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 2-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 2-0:1.0: unable to enumerate USB device on port 1
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 1-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 2-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 2-0:1.0: unable to enumerate USB device on port 1
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 1-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 2-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 2-0:1.0: unable to enumerate USB device on port 1
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 1-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 2-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 2-0:1.0: unable to enumerate USB device on port 1
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030300 PESC CSC LSDA PPS
hub 2-0:1.0: port 1, status 0300, change 0003, 1.5 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x300
ohci_hcd 0000:00:0b.0: auto-stop root hub
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 3:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for UDMA/100
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4: limiting SATA link speed to 1.5 Gbps
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 3:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for UDMA/100
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: limiting speed to UDMA/66:PIO4
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 3:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for UDMA/66
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: limiting speed to UDMA/33:PIO4
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 3:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for UDMA/33
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: limiting speed to PIO4
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 3:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO4
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: limiting speed to PIO3
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 3:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO3
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: limiting speed to PIO0
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 3:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 3:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
PM: Adding info for No Bus:0:0:0:0
PM: Adding info for No Bus:1:0:0:0
PM: Adding info for No Bus:4:0:0:0
PM: Adding info for No Bus:4:0:0:1
PM: Adding info for No Bus:4:0:0:2
PM: Adding info for No Bus:4:0:0:3
PM: Adding info for No Bus:5:0:0:0
sd 0:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
PM: Adding info for No Bus:sda
sda:
sd 1:0:0:0: [sdb] 488397168 512-byte logical blocks: (250 GB/232 GiB)
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
PM: Adding info for No Bus:sdb
sdb:
PM: Adding info for No Bus:sdc
PM: Adding info for No Bus:8:32
PM: Adding info for No Bus:sdd
PM: Adding info for No Bus:8:48
sd 4:0:0:0: [sdc] Attached SCSI removable disk
PM: Adding info for No Bus:sde
PM: Adding info for No Bus:8:64
PM: Adding info for No Bus:sdf
PM: Adding info for No Bus:8:80
sd 5:0:0:0: [sdg] 3981312 512-byte logical blocks: (2.03 GB/1.89 GiB)
sd 4:0:0:1: [sdd] Attached SCSI removable disk
sd 4:0:0:2: [sde] Attached SCSI removable disk
sd 5:0:0:0: [sdg] Write Protect is off
sd 5:0:0:0: [sdg] Mode Sense: 43 00 00 00
sd 5:0:0:0: [sdg] Assuming drive cache: write through
PM: Adding info for No Bus:sdg
sd 4:0:0:3: [sdf] Attached SCSI removable disk
sd 5:0:0:0: [sdg] Assuming drive cache: write through
sdg: sda1 sda2 sda3 < sdg1
PM: Adding info for No Bus:sdg1
PM: Adding info for No Bus:8:96
unknown partition table
PM: Adding info for No Bus:8:16
sd 1:0:0:0: [sdb] Attached SCSI disk
sd 5:0:0:0: [sdg] Assuming drive cache: write through
sd 5:0:0:0: [sdg] Attached SCSI removable disk
>
PM: Adding info for No Bus:sda1
PM: Adding info for No Bus:sda2
PM: Adding info for No Bus:sda3
PM: Adding info for No Bus:8:0
sd 0:0:0:0: [sda] Attached SCSI disk
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 3:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 3:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 3:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 3:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 3:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 3:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 3:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 3:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
INFO: task modprobe:744 blocked for more than 120 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
modprobe D c1c1ff34 0 744 1 0x00000000
c3c05700 00000082 00000002 c1c1ff34 c3c01f04 00000000 c12b6e12 c1c95880
c10e29d1 c1389f04 c233e300 c233e48c 00000000 fffe32ef 00000000 00000000
00000001 c1cc8c40 c3c01f04 c233e48c c1318bf0 00000000 c1d09180 c1dd0900
Call Trace:
[<c10e29d1>] ? sysfs_find_dirent+0x21/0x30
[<c10e24f5>] ? sysfs_add_file_mode+0x55/0x90
[<c104a9dd>] ? async_synchronize_cookie_domain+0xbd/0x150
[<c10445d0>] ? autoremove_wake_function+0x0/0x50
[<c104aa90>] ? async_synchronize_full+0x10/0x30
[<c105a04c>] ? sys_init_module+0xfc/0x220
[<c1003070>] ? syscall_call+0x7/0xb
INFO: task modprobe:750 blocked for more than 120 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
modprobe D c1c2ff34 0 750 1 0x00000000
c3d05700 00000086 00000002 c1c2ff34 c3d01f04 00000000 c12b6e12 c233f100
c10e29d1 c1389f04 c23a2a00 c23a2b8c 00000001 fffe32ed 00000000 00000000
00000001 c1d25c00 c3d01f04 c23a2b8c c1318bf0 00000000 c1d09000 c1dd00c0
Call Trace:
[<c10e29d1>] ? sysfs_find_dirent+0x21/0x30
[<c10e24f5>] ? sysfs_add_file_mode+0x55/0x90
[<c104a9dd>] ? async_synchronize_cookie_domain+0xbd/0x150
[<c10445d0>] ? autoremove_wake_function+0x0/0x50
[<c104aa90>] ? async_synchronize_full+0x10/0x30
[<c105a04c>] ? sys_init_module+0xfc/0x220
[<c1003070>] ? syscall_call+0x7/0xb
INFO: task modprobe:874 blocked for more than 120 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
modprobe D c3c01f20 0 874 1 0x00000000
c3c05700 00000082 000006e2 c3c01f20 00000002 c1c63f30 c1c63f2c c233ea00
c1c63f64 c1389f04 c1c97480 c1c9760c 00000000 fffb7dfe c3c01f20 00000000
c10e24f5 f703fa40 c3c01f04 c1c9760c 000006e2 00000080 00000000 f8e8c0f4
Call Trace:
[<c10e24f5>] ? sysfs_add_file_mode+0x55/0x90
[<f8e89b90>] ? storage_probe+0x0/0x80 [usb_storage]
[<c1242ca9>] ? _spin_lock_irqsave+0x19/0x40
[<c1242ca9>] ? _spin_lock_irqsave+0x19/0x40
[<c104a9dd>] ? async_synchronize_cookie_domain+0xbd/0x150
[<c124049c>] ? printk+0x17/0x1b
[<c10445d0>] ? autoremove_wake_function+0x0/0x50
[<c104aa90>] ? async_synchronize_full+0x10/0x30
[<c105a04c>] ? sys_init_module+0xfc/0x220
[<c1003070>] ? syscall_call+0x7/0xb
INFO: task modprobe:885 blocked for more than 120 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
modprobe D c238df34 0 885 1 0x00000000
c3c05700 00000082 c3c01f04 c238df34 c3c01f04 00000000 c238df5c c1c97480
c238df04 c1389f04 c1c95880 c1c95a0c 00000000 fffe32c6 c3c01f20 00000000
00000000 f703e380 c3c01f04 c1c95a0c 00000000 f8ef9cd4 f8ef6580 c10e2540
Call Trace:
[<f8ef6580>] ? usbhid_probe+0x0/0x360 [usbhid]
[<c10e2540>] ? sysfs_add_file+0x10/0x20
[<c1242ca9>] ? _spin_lock_irqsave+0x19/0x40
[<c1242ca9>] ? _spin_lock_irqsave+0x19/0x40
[<c104a9dd>] ? async_synchronize_cookie_domain+0xbd/0x150
[<f8efd0c6>] ? hid_init+0xc6/0xca [usbhid]
[<c10445d0>] ? autoremove_wake_function+0x0/0x50
[<c104aa90>] ? async_synchronize_full+0x10/0x30
[<c105a04c>] ? sys_init_module+0xfc/0x220
[<c1003070>] ? syscall_call+0x7/0xb
INFO: task modprobe:904 blocked for more than 120 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
modprobe D c3d01f20 0 904 622 0x00000000
c3d05700 00000086 00000832 c3d01f20 00000002 c1c47f30 c1c47f2c c1c96300
f8fe24c4 c1389f04 c233f100 c233f28c 00000001 fffe32c7 c3d01f20 00000000
00000202 c1cc8fc0 c3d01f04 c233f28c 00000832 00000000 c10363f1 f8fecb40
Call Trace:
[<c10363f1>] ? sysctl_set_parent+0x21/0x40
[<c1242f2c>] ? _spin_unlock+0xc/0x30
[<c1242ca9>] ? _spin_lock_irqsave+0x19/0x40
[<c1242ca9>] ? _spin_lock_irqsave+0x19/0x40
[<c104a9dd>] ? async_synchronize_cookie_domain+0xbd/0x150
[<c10445d0>] ? autoremove_wake_function+0x0/0x50
[<c104aa90>] ? async_synchronize_full+0x10/0x30
[<c105a04c>] ? sys_init_module+0xfc/0x220
[<c1003070>] ? syscall_call+0x7/0xb
INFO: task modprobe:905 blocked for more than 120 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
modprobe D c212bf34 0 905 624 0x00000000
c3d05700 00000086 c3d01f04 c212bf34 c3d01f04 00000000 c212bf2c f704dc00
c10e3aed c1389f04 c1c96300 c1c9648c 00000001 fffe32db c3d01f20 00000000
00000202 c1cc81c0 c3d01f04 c1c9648c 00000519 f71dddc0 00000002 c106a750
Call Trace:
[<c10e3aed>] ? sysfs_do_create_link+0x8d/0x120
[<c106a750>] ? mempool_alloc_slab+0x0/0x10
[<c106a760>] ? mempool_free_slab+0x0/0x10
[<c1242ca9>] ? _spin_lock_irqsave+0x19/0x40
[<c1242ca9>] ? _spin_lock_irqsave+0x19/0x40
[<c104a9dd>] ? async_synchronize_cookie_domain+0xbd/0x150
[<f903e13a>] ? init_sd+0x13a/0x17a [sd_mod]
[<c10445d0>] ? autoremove_wake_function+0x0/0x50
[<c104aa90>] ? async_synchronize_full+0x10/0x30
[<c105a04c>] ? sys_init_module+0xfc/0x220
[<c1003070>] ? syscall_call+0x7/0xb
PM: Adding info for No Bus:device-mapper
device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
usb 1-2:1.0: uevent
usb 1-2: uevent
usb 1-2:1.0: uevent
usb 1-2:1.0: uevent
usb 1-2: uevent
usb 1-2: uevent
usb 1-2:1.0: uevent
usb 1-2: uevent
usb 1-2:1.0: uevent
usb 1-2:1.0: uevent
usb 1-2:1.0: uevent
usb 1-2:1.0: uevent
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 3:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 3:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 3:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 3:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 3:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 3:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
INFO: task modprobe:744 blocked for more than 120 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
modprobe D c1c1ff34 0 744 1 0x00000000
c3c05700 00000082 00000002 c1c1ff34 c3c01f04 00000000 c12b6e12 c1c95880
c10e29d1 c1389f04 c233e300 c233e48c 00000000 fffe32ef 00000000 00000000
00000001 c1cc8c40 c3c01f04 c233e48c c1318bf0 00000000 c1d09180 c1dd0900
Call Trace:
[<c10e29d1>] ? sysfs_find_dirent+0x21/0x30
[<c10e24f5>] ? sysfs_add_file_mode+0x55/0x90
[<c104a9dd>] ? async_synchronize_cookie_domain+0xbd/0x150
[<c10445d0>] ? autoremove_wake_function+0x0/0x50
[<c104aa90>] ? async_synchronize_full+0x10/0x30
[<c105a04c>] ? sys_init_module+0xfc/0x220
[<c1003070>] ? syscall_call+0x7/0xb
INFO: task modprobe:750 blocked for more than 120 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
modprobe D c1c2ff34 0 750 1 0x00000000
c3d05700 00000086 00000002 c1c2ff34 c3d01f04 00000000 c12b6e12 c233f100
c10e29d1 c1389f04 c23a2a00 c23a2b8c 00000001 fffe32ed 00000000 00000000
00000001 c1d25c00 c3d01f04 c23a2b8c c1318bf0 00000000 c1d09000 c1dd00c0
Call Trace:
[<c10e29d1>] ? sysfs_find_dirent+0x21/0x30
[<c10e24f5>] ? sysfs_add_file_mode+0x55/0x90
[<c104a9dd>] ? async_synchronize_cookie_domain+0xbd/0x150
[<c10445d0>] ? autoremove_wake_function+0x0/0x50
[<c104aa90>] ? async_synchronize_full+0x10/0x30
[<c105a04c>] ? sys_init_module+0xfc/0x220
[<c1003070>] ? syscall_call+0x7/0xb
INFO: task modprobe:874 blocked for more than 120 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
modprobe D c3c01f20 0 874 1 0x00000000
c3c05700 00000082 000006e2 c3c01f20 00000002 c1c63f30 c1c63f2c c233ea00
c1c63f64 c1389f04 c1c97480 c1c9760c 00000000 fffb7dfe c3c01f20 00000000
c10e24f5 f703fa40 c3c01f04 c1c9760c 000006e2 00000080 00000000 f8e8c0f4
Call Trace:
[<c10e24f5>] ? sysfs_add_file_mode+0x55/0x90
[<f8e89b90>] ? storage_probe+0x0/0x80 [usb_storage]
[<c1242ca9>] ? _spin_lock_irqsave+0x19/0x40
[<c1242ca9>] ? _spin_lock_irqsave+0x19/0x40
[<c104a9dd>] ? async_synchronize_cookie_domain+0xbd/0x150
[<c124049c>] ? printk+0x17/0x1b
[<c10445d0>] ? autoremove_wake_function+0x0/0x50
[<c104aa90>] ? async_synchronize_full+0x10/0x30
[<c105a04c>] ? sys_init_module+0xfc/0x220
[<c1003070>] ? syscall_call+0x7/0xb
INFO: task modprobe:885 blocked for more than 120 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
modprobe D c238df34 0 885 1 0x00000000
c3c05700 00000082 c3c01f04 c238df34 c3c01f04 00000000 c238df5c c1c97480
c238df04 c1389f04 c1c95880 c1c95a0c 00000000 fffe32c6 c3c01f20 00000000
00000000 f703e380 c3c01f04 c1c95a0c 00000000 f8ef9cd4 f8ef6580 c10e2540
Call Trace:
[<f8ef6580>] ? usbhid_probe+0x0/0x360 [usbhid]
[<c10e2540>] ? sysfs_add_file+0x10/0x20
[<c1242ca9>] ? _spin_lock_irqsave+0x19/0x40
[<c1242ca9>] ? _spin_lock_irqsave+0x19/0x40
[<c104a9dd>] ? async_synchronize_cookie_domain+0xbd/0x150
[<f8efd0c6>] ? hid_init+0xc6/0xca [usbhid]
[<c10445d0>] ? autoremove_wake_function+0x0/0x50
[<c104aa90>] ? async_synchronize_full+0x10/0x30
[<c105a04c>] ? sys_init_module+0xfc/0x220
[<c1003070>] ? syscall_call+0x7/0xb
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 3:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 3:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: WARNING: synchronous SCSI scan failed without making any progress,
switching to async
md: raid0 personality registered for level 0
ata4: EH complete
ide-cd driver 5.00
PM: Adding info for No Bus:0.0
ide-cd: hda: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2000kB Cache
Uniform CD-ROM driver Revision: 3.20
usb 1-3.1.2.1:1.0: uevent
usb 1-3.1.2.1: uevent
md: raid1 personality registered for level 1
usb 1-3.1.2.1:1.0: uevent
xor: automatically using best checksumming function: pIII_sse
pIII_sse : 7516.000 MB/sec
xor: using function: pIII_sse (7516.000 MB/sec)
PM: Adding info for No Bus:hda
PM: Adding info for No Bus:3:0
raid6: int32x1 875 MB/s
usb 1-3.1.2.1:1.0: uevent
usb 1-3.1.2.1: uevent
usb 1-3.1.2.1:1.0: uevent
raid6: int32x2 843 MB/s
raid6: int32x4 703 MB/s
raid6: int32x8 585 MB/s
raid6: mmxx1 2742 MB/s
PM: Adding info for No Bus:dm-0
PM: Adding info for No Bus:253:0
raid6: mmxx2 3156 MB/s
raid6: sse1x1 1886 MB/s
raid6: sse1x2 2437 MB/s
PM: Adding info for No Bus:dm-1
PM: Adding info for No Bus:253:1
PM: Adding info for No Bus:dm-2
raid6: sse2x1 3531 MB/s
PM: Adding info for No Bus:253:2
PM: Adding info for No Bus:dm-3
PM: Adding info for No Bus:253:3
PM: Adding info for No Bus:dm-4
PM: Adding info for No Bus:253:4
PM: Adding info for No Bus:dm-5
PM: Adding info for No Bus:253:5
PM: Adding info for No Bus:dm-6
PM: Adding info for No Bus:253:6
raid6: sse2x2 4164 MB/s
raid6: using algorithm sse2x2 (4164 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
PM: Removing info for No Bus:253:1
PM: Removing info for No Bus:dm-1
md: raid10 personality registered for level 10
PM: Marking nosave pages: 000000000009c000 - 0000000000100000
PM: Basic memory bitmaps created
PM: Basic memory bitmaps freed
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with writeback data mode.
udev: starting version 146
usb usb2: uevent
usb 2-0:1.0: uevent
usb usb1: uevent
usb 1-0:1.0: uevent
usb 1-2: uevent
usb 1-2:1.0: uevent
usb 1-3: uevent
usb 1-3.1: uevent
usb 1-3.1.1: uevent
usb 1-3.1.1:1.0: uevent
usb 1-3.1.1:1.1: uevent
usb 1-3.1.2: uevent
usb 1-3.1.2.1: uevent
usb 1-3.1.2.1:1.0: uevent
usb 1-3.1.2.2: uevent
usb 1-3.1.2.2:1.0: uevent
usb 1-3.1.2:1.0: uevent
usb 1-3.1:1.0: uevent
usb 1-3:1.0: uevent
usb 1-6: uevent
usb 1-6.1: uevent
usb 1-6.1:1.0: uevent
usb 1-6.3: uevent
usb 1-6.3.3: uevent
usb 1-6.3.3:1.0: uevent
usb 1-6.3.3:1.1: uevent
usb 1-6.3:1.0: uevent
usb 1-6:1.0: uevent
usb usb2: uevent
usb usb1: uevent
usb usb2: uevent
usb usb1: uevent
usb 1-2: uevent
usb 1-6: uevent
usb 1-3: uevent
usb 1-3: uevent
usb 1-6: uevent
usb 1-2: uevent
usb 1-2:1.0: uevent
usb 1-2: uevent
usb 1-2:1.0: uevent
usb 1-2: uevent
usb 1-2:1.0: uevent
usb 1-2: uevent
usb 1-2:1.0: uevent
usb 1-2: uevent
usb 1-2:1.0: uevent
usb 1-2:1.0: uevent
usb 1-2:1.0: uevent
usb 1-2:1.0: uevent
usb 1-6.1: uevent
usb 1-6.3: uevent
usb 1-6.1: uevent
usb 1-3.1: uevent
usb 1-6.3: uevent
usb 1-3.1: uevent
PM: Adding info for No Bus:rtc
Real Time Clock Driver v1.12b
usb 1-3.1.2: uevent
usb 1-6.3.3: uevent
usb 1-3.1.2: uevent
usb 1-6.3.3: uevent
usb 1-3.1.1: uevent
usb 1-3.1.2.1: uevent
usb 1-3.1.2.1: uevent
usb 1-3.1.1: uevent
usb 1-3.1.2.1:1.0: uevent
usb 1-3.1.2.1: uevent
PM: Adding info for No Bus:input6
input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input6
ACPI: Power Button [PWRB]
PM: Adding info for No Bus:input7
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input7
ACPI: Power Button [PWRF]
usb 1-3.1.2.2: uevent
usb 1-3.1.2.1:1.0: uevent
usb 1-3.1.2.2: uevent
ACPI: SSDT 7fefa940 00175 (v01 Nvidia ASUSACPI 42302E31 AWRD 00000000)
PM: Adding info for No Bus:cooling_device1
processor LNXCPU:00: registered as cooling_device1
ACPI: SSDT 7fefad50 000CE (v01 Nvidia ASUSACPI 42302E31 AWRD 00000000)
PM: Adding info for No Bus:cooling_device2
processor LNXCPU:01: registered as cooling_device2
PM: Adding info for No Bus:event0
PM: Adding info for No Bus:event1
PM: Adding info for No Bus:event2
PM: Adding info for No Bus:event3
PM: Adding info for No Bus:event4
PM: Adding info for No Bus:event5
PM: Adding info for No Bus:event6
PM: Adding info for No Bus:event7
usb 1-6.1:1.0: uevent
usb 1-6.1: uevent
usb 1-6.1:1.0: uevent
usb 1-6.1:1.0: uevent
usb 1-6.1: uevent
usb 1-6.1:1.0: uevent
PM: Adding info for No Bus:raw1394
ieee1394: raw1394: /dev/raw1394 device initialized
usb 1-6.3.3:1.0: uevent
usb 1-6.3.3:1.1: uevent
usb 1-6.3.3: uevent
usb 1-6.3.3: uevent
usb 1-6.3.3:1.1: uevent
usb 1-6.3.3: uevent
usb 1-6.3.3:1.0: uevent
usb 1-6.3.3:1.1: uevent
usb 1-6.3.3:1.1: uevent
PM: Adding info for No Bus:hwmon0
usb 1-3.1.2.2:1.0: uevent
usb 1-3.1.2.2: uevent
usb 1-3.1.2.2:1.0: uevent
usb 1-3.1.1:1.0: uevent
usb 1-3.1.1: uevent
usb 1-3.1.2.2:1.0: uevent
usb 1-3.1.1:1.1: uevent
usb 1-3.1.2.2: uevent
usb 1-3.1.1: uevent
usb 1-3.1.1:1.1: uevent
usb 1-3.1.1: uevent
usb 1-3.1.1:1.1: uevent
usb 1-3.1.2.2:1.0: uevent
usb 1-3.1.1:1.1: uevent
usb 1-3.1.1:1.0: uevent
ACPI: I/O resource nForce2_smbus [0x5000-0x503f] conflicts with ACPI region SM00 [0x5000-0x5005]
ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
nForce2_smbus 0000:00:0a.1: Error probing SMB1.
PM: Adding info for i2c:i2c-0
i2c i2c-0: nForce2 SMBus adapter at 0x5100
PM: Adding info for No Bus:dv1394-0
PM: Adding info for No Bus:timer
hda: UDMA/66 mode selected
hda: task_no_data_intr: status=0x41 { DriveReady Error }
hda: task_no_data_intr: error=0x04 { AbortedCommand }
hda: possibly failed opcode: 0xe3
PM: Adding info for No Bus:seq
PM: Adding info for No Bus:sequencer
PM: Adding info for No Bus:sequencer2
ACPI: PCI Interrupt Link [AAZA] enabled at IRQ 23
HDA Intel 0000:00:10.1: PCI INT B -> Link[AAZA] -> GSI 23 (level, low) -> IRQ 23
HDA Intel 0000:00:10.1: setting latency timer to 64
PM: Adding info for No Bus:input8
input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:10.1/input/input8
PM: Adding info for No Bus:event8
PM: Adding info for No Bus:card0
PM: Adding info for No Bus:pcmC0D1p
PM: Adding info for No Bus:adsp
PM: Adding info for No Bus:pcmC0D0p
PM: Adding info for No Bus:pcmC0D0c
PM: Adding info for No Bus:dsp
PM: Adding info for No Bus:audio
PM: Adding info for No Bus:hwC0D0
PM: Adding info for No Bus:controlC0
PM: Adding info for No Bus:mixer
PM: Adding info for No Bus:vcs2
PM: Adding info for No Bus:vcsa2
PM: Adding info for No Bus:vcs3
PM: Adding info for No Bus:vcsa3
PM: Adding info for No Bus:vcs4
PM: Adding info for No Bus:vcsa4
PM: Adding info for No Bus:vcs5
PM: Adding info for No Bus:vcsa5
PM: Adding info for No Bus:vcs6
PM: Adding info for No Bus:vcsa6
hda: UDMA/66 mode selected
hda: task_no_data_intr: status=0x41 { DriveReady Error }
hda: task_no_data_intr: error=0x04 { AbortedCommand }
hda: possibly failed opcode: 0xe3
EXT3 FS on dm-2, internal journal
i2c /dev entries driver
PM: Adding info for No Bus:i2c-0
it87: Found IT8712F chip at 0x290, revision 7
it87: in3 is VCC (+5V)
it87: in7 is VCCH (+5V Stand-By)
ACPI: I/O resource it87 [0x295-0x296] conflicts with ACPI region HWRE [0x295-0x296]
ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
fuse init (API version 7.13)
PM: Adding info for No Bus:fuse
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-5, internal journal
EXT3-fs: mounted filesystem with writeback data mode.
PM: Adding info for No Bus:253:3-fuseblk
PM: Adding info for No Bus:253:6-fuseblk
Adding 4194296k swap on /mnt/oldlin/4G-memory.swap. Priority:-1 extents:1057 across:4264956k
r8169: eth1: link up
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PM: Adding info for No Bus:0:16
PM: Adding info for No Bus:0:17
PM: Adding info for No Bus:0:18
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 3:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 3:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 3:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 3:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 3:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 3:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 3:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 3:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 3:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
[-- Attachment #3: lsmod-disable-clear-ua --]
[-- Type: application/octet-stream, Size: 3536 bytes --]
Module Size Used by
nfs 249128 3
lockd 57825 1 nfs
nfs_acl 2071 1 nfs
auth_rpcgss 29754 1 nfs
sunrpc 159001 13 nfs,lockd,nfs_acl,auth_rpcgss
af_packet 15662 2
fuse 51248 5
hwmon_vid 2036 0
eeprom 2873 0
i2c_dev 4354 0
snd_hda_codec_analog 50520 1
snd_hda_intel 17736 0
snd_hda_codec 56238 2 snd_hda_codec_analog,snd_hda_intel
snd_hwdep 5046 1 snd_hda_codec
snd_pcm_oss 34307 0
snd_mixer_oss 12821 1 snd_pcm_oss
snd_pcm 58403 3 snd_hda_intel,snd_hda_codec,snd_pcm_oss
snd_seq_dummy 1107 0
snd_seq_oss 24869 0
snd_seq_midi 3944 0
snd_rawmidi 15103 1 snd_seq_midi
snd_seq_midi_event 4300 2 snd_seq_oss,snd_seq_midi
snd_seq 43131 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
snd_timer 15170 2 snd_pcm,snd_seq
snd_seq_device 4513 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
dv1394 14976 0
snd 41841 14 snd_hda_codec_analog,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
i2c_nforce2 4688 0
joydev 7768 0
asus_atk0110 8278 0
raw1394 20216 0
evdev 6749 0
i2c_core 15344 3 eeprom,i2c_dev,i2c_nforce2
processor 30516 0
soundcore 4623 1 snd
button 3646 0
rtc 4386 0
snd_page_alloc 5529 2 snd_hda_intel,snd_pcm
ext3 108580 2
jbd 40305 1 ext3
raid10 20889 0
raid456 51884 0
async_raid6_recov 3422 1 raid456
async_pq 1600 2 raid456,async_raid6_recov
raid6_pq 78504 2 async_raid6_recov,async_pq
async_xor 977 3 raid456,async_raid6_recov,async_pq
xor 15233 1 async_xor
async_memcpy 630 2 raid456,async_raid6_recov
async_tx 1217 5 raid456,async_raid6_recov,async_pq,async_xor,async_memcpy
raid1 19847 0
ide_cd_mod 24281 0
pata_amd 7777 0
raid0 6633 0
dm_mod 50907 17
md_mod 80538 4 raid10,raid456,raid1,raid0
sd_mod 27266 2
cdrom 30903 1 ide_cd_mod
usbhid 22405 0
usb_storage 33345 0
pata_acpi 2240 0
sata_nv 17946 2
libata 136504 3 pata_amd,pata_acpi,sata_nv
ohci1394 25565 1 dv1394
r8169 31894 0
bitrev 907 1 r8169
crc32 2955 1 r8169
mii 3194 1 r8169
ohci_hcd 32904 0
ehci_hcd 46561 0
amd74xx 3908 0
ieee1394 61913 3 dv1394,raw1394,ohci1394
usbcore 125976 5 usbhid,usb_storage,ohci_hcd,ehci_hcd
scsi_mod 115368 3 sd_mod,usb_storage,libata
ide_core 77660 2 ide_cd_mod,amd74xx
thermal 10035 0
fan 2574 0
thermal_sys 10237 3 processor,thermal,fan
unix 20299 6
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: sata_nv times out for BD-ROM iHOS104-08
2010-02-17 16:14 ` Cengiz Günay
@ 2010-02-18 1:50 ` Tejun Heo
2010-02-20 19:11 ` Cengiz Günay
0 siblings, 1 reply; 28+ messages in thread
From: Tejun Heo @ 2010-02-18 1:50 UTC (permalink / raw)
To: Cengiz Günay; +Cc: Robert Hancock, linux-kernel, linux-ide
[-- Attachment #1: Type: text/plain, Size: 811 bytes --]
On 02/18/2010 01:14 AM, Cengiz Günay wrote:
> 2010/2/1 Tejun Heo <tj@kernel.org>:
>
>> Can you please attach full dmesg w/ the patch applied w/o any kernel
>> parameter? I'm curious where the hda warnings are coming from. Is
>> generic IDE driver loaded?
>
> The dmesg snippet I attached last time was w/o any kernel parameters.
> This time I'm attaching the full dmesg output. hda is my other DVD-RW
> drive, I'm not sure what the warnings mean. ide_core is loaded, but
> not the ide-generic or ide-pci-generic modules, although they are
> available. Would you like me to force them to load?
No, I was concerned because there were a few cases where two drivers
were attached to the same controller but I don't think that's possible
here.
Does the attached patch make any difference?
Thanks.
--
tejun
[-- Attachment #2: drain-from-atapi_pio_bytes.patch --]
[-- Type: text/x-patch, Size: 1167 bytes --]
diff --git a/drivers/ata/libata-sff.c b/drivers/ata/libata-sff.c
index 730ef3c..d189b48 100644
--- a/drivers/ata/libata-sff.c
+++ b/drivers/ata/libata-sff.c
@@ -1070,6 +1070,7 @@ static void atapi_pio_bytes(struct ata_queued_cmd *qc)
struct ata_eh_info *ehi = &dev->link->eh_info;
unsigned int ireason, bc_lo, bc_hi, bytes;
int i_write, do_write = (qc->tf.flags & ATA_TFLAG_WRITE) ? 1 : 0;
+ u8 stat;
/* Abuse qc->result_tf for temp storage of intermediate TF
* here to save some kernel stack usage.
@@ -1099,6 +1100,21 @@ static void atapi_pio_bytes(struct ata_queued_cmd *qc)
if (unlikely(__atapi_pio_bytes(qc, bytes)))
goto err_out;
+
+ /* this really should be done only after the final transfer is complete */
+ stat = ata_sff_altstatus(ap);
+ if (stat & ATA_DRQ) {
+ int count;
+
+ ata_port_printk(ap, KERN_INFO, "stat=%x after atapi_pio_bytes\n", stat);
+
+ for (count = 0; (ap->ops->sff_check_status(ap) & ATA_DRQ)
+ && count < 65536; count += 2)
+ ioread16(ap->ioaddr.data_addr);
+ if (count)
+ ata_port_printk(ap, KERN_DEBUG,
+ "drained %d bytes to clear DRQ.\n", count);
+ }
ata_sff_sync(ap); /* flush */
return;
^ permalink raw reply related [flat|nested] 28+ messages in thread
* Re: sata_nv times out for BD-ROM iHOS104-08
2010-02-18 1:50 ` Tejun Heo
@ 2010-02-20 19:11 ` Cengiz Günay
2010-02-21 1:01 ` Tejun Heo
0 siblings, 1 reply; 28+ messages in thread
From: Cengiz Günay @ 2010-02-20 19:11 UTC (permalink / raw)
To: Tejun Heo; +Cc: Robert Hancock, linux-kernel, linux-ide
[-- Attachment #1: Type: text/plain, Size: 510 bytes --]
On Wed, Feb 17, 2010 at 8:50 PM, Tejun Heo <tj@kernel.org> wrote:
> No, I was concerned because there were a few cases where two drivers
> were attached to the same controller but I don't think that's possible
> here.
Ok.
> Does the attached patch make any difference?
Not that I can tell. I still get an infinite loop of ata4 errors. I
attached a full dmesg output with the patch. Note that I have both the
patches disable-clear-ua and drain-from-atapi-pio-bytes applied at the
same time.
Thanks,
-Cengiz
[-- Attachment #2: dmesg-sata_nv-drain-from-atapi_pio_bytes --]
[-- Type: application/octet-stream, Size: 123029 bytes --]
0F:17
PM: Adding info for acpi:PNP0C0F:18
PM: Adding info for acpi:PNP0C0F:19
PM: Adding info for acpi:PNP0C0F:1a
PM: Adding info for acpi:PNP0C0F:1b
PM: Adding info for acpi:PNP0C0F:1c
PM: Adding info for acpi:PNP0C0F:1d
PM: Adding info for acpi:PNP0C0F:1e
PM: Adding info for acpi:PNP0C0F:1f
PM: Adding info for acpi:PNP0C0F:20
PM: Adding info for acpi:PNP0C0F:21
PM: Adding info for acpi:PNP0C0F:22
PM: Adding info for acpi:PNP0C0F:23
PM: Adding info for acpi:PNP0C0F:24
PM: Adding info for acpi:PNP0C0F:25
PM: Adding info for acpi:PNP0C0F:26
PM: Adding info for acpi:PNP0C0F:27
PM: Adding info for acpi:PNP0C0F:28
PM: Adding info for acpi:PNP0C02:02
PM: Adding info for acpi:PNP0C01:00
PM: Adding info for acpi:LNXTHERM:00
PM: Adding info for acpi:PNP0C0B:00
PM: Adding info for acpi:LNXTHERM:01
PM: Adding info for acpi:LNXPWRBN:00
ACPI: No dock devices found.
ACPI: PCI Root Bridge [PCI0] (0000:00)
PM: Adding info for No Bus:pci0000:00
PM: Adding info for No Bus:0000:00
pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:02.0: PME# disabled
pci 0000:00:04.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:04.0: PME# disabled
pci 0000:00:05.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:05.0: PME# disabled
pci 0000:00:06.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:06.0: PME# disabled
pci 0000:00:07.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:07.0: PME# disabled
pci 0000:00:0a.1: reg 20 io port: [0x5000-0x503f]
pci 0000:00:0a.1: reg 24 io port: [0x5100-0x513f]
pci 0000:00:0a.1: PME# supported from D3hot D3cold
pci 0000:00:0a.1: PME# disabled
pci 0000:00:0b.0: reg 10 32bit mmio: [0xd5006000-0xd5006fff]
pci 0000:00:0b.0: supports D1 D2
pci 0000:00:0b.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:0b.0: PME# disabled
pci 0000:00:0b.1: reg 10 32bit mmio: [0xd5007000-0xd50070ff]
pci 0000:00:0b.1: supports D1 D2
pci 0000:00:0b.1: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:0b.1: PME# disabled
pci 0000:00:0d.0: reg 20 io port: [0xf000-0xf00f]
pci 0000:00:0e.0: reg 10 io port: [0x9f0-0x9f7]
pci 0000:00:0e.0: reg 14 io port: [0xbf0-0xbf3]
pci 0000:00:0e.0: reg 18 io port: [0x970-0x977]
pci 0000:00:0e.0: reg 1c io port: [0xb70-0xb73]
pci 0000:00:0e.0: reg 20 io port: [0xd400-0xd40f]
pci 0000:00:0e.0: reg 24 32bit mmio: [0xd5004000-0xd5004fff]
pci 0000:00:0f.0: reg 10 io port: [0x9e0-0x9e7]
pci 0000:00:0f.0: reg 14 io port: [0xbe0-0xbe3]
pci 0000:00:0f.0: reg 18 io port: [0x960-0x967]
pci 0000:00:0f.0: reg 1c io port: [0xb60-0xb63]
pci 0000:00:0f.0: reg 20 io port: [0xe800-0xe80f]
pci 0000:00:0f.0: reg 24 32bit mmio: [0xd5005000-0xd5005fff]
pci 0000:00:10.1: reg 10 32bit mmio: [0xd5000000-0xd5003fff]
pci 0000:00:10.1: PME# supported from D3hot D3cold
pci 0000:00:10.1: PME# disabled
pci 0000:01:00.0: reg 10 32bit mmio: [0xd0000000-0xd0ffffff]
pci 0000:01:00.0: reg 14 64bit mmio pref: [0xc0000000-0xcfffffff]
pci 0000:01:00.0: reg 1c 64bit mmio: [0xd1000000-0xd1ffffff]
pci 0000:01:00.0: reg 24 io port: [0xa000-0xa07f]
pci 0000:01:00.0: reg 30 32bit mmio pref: [0xd2000000-0xd201ffff]
pci 0000:00:02.0: bridge io port: [0xa000-0xafff]
pci 0000:00:02.0: bridge 32bit mmio: [0xd0000000-0xd2ffffff]
pci 0000:00:02.0: bridge 64bit mmio pref: [0xc0000000-0xcfffffff]
pci 0000:06:06.0: reg 10 32bit mmio: [0xd4001000-0xd40017ff]
pci 0000:06:06.0: reg 14 io port: [0xb000-0xb07f]
pci 0000:06:06.0: supports D2
pci 0000:06:06.0: PME# supported from D2 D3hot D3cold
pci 0000:06:06.0: PME# disabled
pci 0000:06:07.0: reg 10 io port: [0xb400-0xb4ff]
pci 0000:06:07.0: reg 14 32bit mmio: [0xd4000000-0xd40000ff]
pci 0000:06:07.0: reg 30 32bit mmio pref: [0xd3000000-0xd301ffff]
pci 0000:06:07.0: supports D1 D2
pci 0000:06:07.0: PME# supported from D1 D2 D3hot D3cold
pci 0000:06:07.0: PME# disabled
pci 0000:00:10.0: transparent bridge
pci 0000:00:10.0: bridge io port: [0xb000-0xbfff]
pci 0000:00:10.0: bridge 32bit mmio: [0xd3000000-0xd4ffffff]
pci_bus 0000:00: on NUMA node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
PM: Adding info for pci:0000:00:00.0
PM: Adding info for pci:0000:00:00.1
PM: Adding info for pci:0000:00:00.2
PM: Adding info for pci:0000:00:00.3
PM: Adding info for pci:0000:00:00.4
PM: Adding info for pci:0000:00:01.0
PM: Adding info for pci:0000:00:01.1
PM: Adding info for pci:0000:00:01.2
PM: Adding info for pci:0000:00:01.3
PM: Adding info for pci:0000:00:01.4
PM: Adding info for pci:0000:00:01.5
PM: Adding info for pci:0000:00:01.6
PM: Adding info for pci:0000:00:02.0
PM: Adding info for pci:0000:00:04.0
PM: Adding info for pci:0000:00:05.0
PM: Adding info for pci:0000:00:06.0
PM: Adding info for pci:0000:00:07.0
PM: Adding info for pci:0000:00:09.0
PM: Adding info for pci:0000:00:0a.0
PM: Adding info for pci:0000:00:0a.1
PM: Adding info for pci:0000:00:0a.2
PM: Adding info for pci:0000:00:0b.0
PM: Adding info for pci:0000:00:0b.1
PM: Adding info for pci:0000:00:0d.0
PM: Adding info for pci:0000:00:0e.0
PM: Adding info for pci:0000:00:0f.0
PM: Adding info for pci:0000:00:10.0
PM: Adding info for pci:0000:00:10.1
PM: Adding info for pci:0000:01:00.0
PM: Adding info for No Bus:0000:01
PM: Adding info for No Bus:0000:02
PM: Adding info for No Bus:0000:03
PM: Adding info for No Bus:0000:04
PM: Adding info for No Bus:0000:05
PM: Adding info for pci:0000:06:06.0
PM: Adding info for pci:0000:06:07.0
PM: Adding info for No Bus:0000:06
ACPI: PCI Interrupt Link [LNK1] (IRQs 5 7 9 *10 11 14 15)
ACPI: PCI Interrupt Link [LNK2] (IRQs *5 7 9 10 11 14 15)
ACPI: PCI Interrupt Link [LNK3] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK4] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK5] (IRQs 5 *7 9 10 11 14 15)
ACPI: PCI Interrupt Link [LNK6] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK7] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK8] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LUBA] (IRQs 5 *7 9 10 11 14 15)
ACPI: PCI Interrupt Link [LUBB] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LMAC] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LACI] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LAZA] (IRQs 5 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [LPMU] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LMCI] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSMB] (IRQs 5 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [LUB2] (IRQs *5 7 9 10 11 14 15)
ACPI: PCI Interrupt Link [LIDE] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSID] (IRQs 5 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [LFID] (IRQs 5 7 9 *10 11 14 15)
ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0
ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0
ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0, disabled.
ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled.
ACPI: PCI Interrupt Link [APC5] (IRQs 16) *0
ACPI: PCI Interrupt Link [APC6] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APC7] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APC8] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APMU] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [AAZA] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0
PM: Adding info for No Bus:vga_arbiter
vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
vgaarb: loaded
PCI: Using ACPI for IRQ routing
PM: Adding info for No Bus:lo
hpet0: at MMIO 0xfeff0000, IRQs 2, 8, 31
hpet0: 3 comparators, 32-bit 25.000000 MHz counter
Switching to clocksource tsc
pnp: PnP ACPI init
PM: Adding info for No Bus:pnp0
ACPI: bus type pnp registered
PM: Adding info for pnp:00:00
PM: Adding info for pnp:00:01
PM: Adding info for pnp:00:02
PM: Adding info for pnp:00:03
PM: Adding info for pnp:00:04
PM: Adding info for pnp:00:05
PM: Adding info for pnp:00:06
PM: Adding info for pnp:00:07
PM: Adding info for pnp:00:08
PM: Adding info for pnp:00:09
pnp: PnP ACPI: found 10 devices
ACPI: ACPI bus type pnp unregistered
PnPBIOS: Disabled by ACPI PNP
system 00:01: ioport range 0x4000-0x407f has been reserved
system 00:01: ioport range 0x4080-0x40ff has been reserved
system 00:01: ioport range 0x4400-0x447f has been reserved
system 00:01: ioport range 0x4480-0x44ff has been reserved
system 00:01: ioport range 0x4800-0x487f has been reserved
system 00:01: ioport range 0x4880-0x48ff has been reserved
system 00:02: ioport range 0x4d0-0x4d1 has been reserved
system 00:02: ioport range 0x800-0x87f has been reserved
system 00:02: ioport range 0x290-0x297 has been reserved
system 00:02: ioport range 0x880-0x88f has been reserved
system 00:08: iomem range 0xe0000000-0xefffffff has been reserved
system 00:09: iomem range 0xdbc00-0xdbfff has been reserved
system 00:09: iomem range 0xf0000-0xf7fff could not be reserved
system 00:09: iomem range 0xf8000-0xfbfff could not be reserved
system 00:09: iomem range 0xfc000-0xfffff could not be reserved
system 00:09: iomem range 0xfeff0000-0xfeff00ff has been reserved
system 00:09: iomem range 0x7fef0000-0x7fefffff could not be reserved
system 00:09: iomem range 0xffff0000-0xffffffff has been reserved
system 00:09: iomem range 0x0-0x9ffff could not be reserved
system 00:09: iomem range 0x100000-0x7feeffff could not be reserved
system 00:09: iomem range 0xfec00000-0xfec00fff could not be reserved
system 00:09: iomem range 0xfee00000-0xfee00fff has been reserved
system 00:09: iomem range 0xfeff0000-0xfeff03ff could not be reserved
PM: Adding info for No Bus:mem
PM: Adding info for No Bus:kmem
PM: Adding info for No Bus:null
PM: Adding info for No Bus:port
PM: Adding info for No Bus:zero
PM: Adding info for No Bus:full
PM: Adding info for No Bus:random
PM: Adding info for No Bus:urandom
PM: Adding info for No Bus:kmsg
pci 0000:06:07.0: BAR 6: address space collision on of device [0xd3000000-0xd301ffff]
pci 0000:00:02.0: PCI bridge, secondary bus 0000:01
pci 0000:00:02.0: IO window: 0xa000-0xafff
pci 0000:00:02.0: MEM window: 0xd0000000-0xd2ffffff
pci 0000:00:02.0: PREFETCH window: 0x000000c0000000-0x000000cfffffff
pci 0000:00:04.0: PCI bridge, secondary bus 0000:02
pci 0000:00:04.0: IO window: disabled
pci 0000:00:04.0: MEM window: disabled
pci 0000:00:04.0: PREFETCH window: disabled
pci 0000:00:05.0: PCI bridge, secondary bus 0000:03
pci 0000:00:05.0: IO window: disabled
pci 0000:00:05.0: MEM window: disabled
pci 0000:00:05.0: PREFETCH window: disabled
pci 0000:00:06.0: PCI bridge, secondary bus 0000:04
pci 0000:00:06.0: IO window: disabled
pci 0000:00:06.0: MEM window: disabled
pci 0000:00:06.0: PREFETCH window: disabled
pci 0000:00:07.0: PCI bridge, secondary bus 0000:05
pci 0000:00:07.0: IO window: disabled
pci 0000:00:07.0: MEM window: disabled
pci 0000:00:07.0: PREFETCH window: disabled
pci 0000:00:10.0: PCI bridge, secondary bus 0000:06
pci 0000:00:10.0: IO window: 0xb000-0xbfff
pci 0000:00:10.0: MEM window: 0xd3000000-0xd4ffffff
pci 0000:00:10.0: PREFETCH window: 0x80000000-0x800fffff
pci 0000:00:02.0: setting latency timer to 64
pci 0000:00:04.0: setting latency timer to 64
pci 0000:00:05.0: setting latency timer to 64
pci 0000:00:06.0: setting latency timer to 64
pci 0000:00:07.0: setting latency timer to 64
pci 0000:00:10.0: setting latency timer to 64
pci_bus 0000:00: resource 0 io: [0x00-0xffff]
pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
pci_bus 0000:01: resource 0 io: [0xa000-0xafff]
pci_bus 0000:01: resource 1 mem: [0xd0000000-0xd2ffffff]
pci_bus 0000:01: resource 2 pref mem [0xc0000000-0xcfffffff]
pci_bus 0000:06: resource 0 io: [0xb000-0xbfff]
pci_bus 0000:06: resource 1 mem: [0xd3000000-0xd4ffffff]
pci_bus 0000:06: resource 2 pref mem [0x80000000-0x800fffff]
pci_bus 0000:06: resource 3 io: [0x00-0xffff]
pci_bus 0000:06: resource 4 mem: [0x000000-0xffffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
pci 0000:01:00.0: Boot video device
Trying to unpack rootfs image as initramfs...
Freeing initrd memory: 20743k freed
PM: Adding info for No Bus:mcelog
PM: Adding info for No Bus:msr0
PM: Adding info for No Bus:msr1
PM: Adding info for platform:pcspkr
PM: Adding info for No Bus:snapshot
highmem bounce pool size: 64 pages
ROMFS MTD (C) 2007 Red Hat, Inc.
msgmni has been set to 1733
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
pcieport 0000:00:02.0: setting latency timer to 64
PM: Adding info for pci_express:0000:00:02.0:pcie08
pcieport 0000:00:04.0: setting latency timer to 64
PM: Adding info for pci_express:0000:00:04.0:pcie08
pcieport 0000:00:05.0: setting latency timer to 64
PM: Adding info for pci_express:0000:00:05.0:pcie08
pcieport 0000:00:06.0: setting latency timer to 64
PM: Adding info for pci_express:0000:00:06.0:pcie08
pcieport 0000:00:07.0: setting latency timer to 64
PM: Adding info for pci_express:0000:00:07.0:pcie08
PM: Adding info for No Bus:pnp1
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
PM: Adding info for No Bus:tty
PM: Adding info for No Bus:console
PM: Adding info for No Bus:tty0
PM: Adding info for No Bus:vcs
PM: Adding info for No Bus:vcsa
PM: Adding info for No Bus:vcs1
PM: Adding info for No Bus:vcsa1
PM: Adding info for No Bus:tty1
PM: Adding info for No Bus:tty2
PM: Adding info for No Bus:tty3
PM: Adding info for No Bus:tty4
PM: Adding info for No Bus:tty5
PM: Adding info for No Bus:tty6
PM: Adding info for No Bus:tty7
PM: Adding info for No Bus:tty8
PM: Adding info for No Bus:tty9
PM: Adding info for No Bus:tty10
PM: Adding info for No Bus:tty11
PM: Adding info for No Bus:tty12
PM: Adding info for No Bus:tty13
PM: Adding info for No Bus:tty14
PM: Adding info for No Bus:tty15
PM: Adding info for No Bus:tty16
PM: Adding info for No Bus:tty17
PM: Adding info for No Bus:tty18
PM: Adding info for No Bus:tty19
PM: Adding info for No Bus:tty20
PM: Adding info for No Bus:tty21
PM: Adding info for No Bus:tty22
PM: Adding info for No Bus:tty23
PM: Adding info for No Bus:tty24
PM: Adding info for No Bus:tty25
PM: Adding info for No Bus:tty26
PM: Adding info for No Bus:tty27
PM: Adding info for No Bus:tty28
PM: Adding info for No Bus:tty29
PM: Adding info for No Bus:tty30
PM: Adding info for No Bus:tty31
PM: Adding info for No Bus:tty32
PM: Adding info for No Bus:tty33
PM: Adding info for No Bus:tty34
PM: Adding info for No Bus:tty35
PM: Adding info for No Bus:tty36
PM: Adding info for No Bus:tty37
PM: Adding info for No Bus:tty38
PM: Adding info for No Bus:tty39
PM: Adding info for No Bus:tty40
PM: Adding info for No Bus:tty41
PM: Adding info for No Bus:tty42
PM: Adding info for No Bus:tty43
PM: Adding info for No Bus:tty44
PM: Adding info for No Bus:tty45
PM: Adding info for No Bus:tty46
PM: Adding info for No Bus:tty47
PM: Adding info for No Bus:tty48
PM: Adding info for No Bus:tty49
PM: Adding info for No Bus:tty50
PM: Adding info for No Bus:tty51
PM: Adding info for No Bus:tty52
PM: Adding info for No Bus:tty53
PM: Adding info for No Bus:tty54
PM: Adding info for No Bus:tty55
PM: Adding info for No Bus:tty56
PM: Adding info for No Bus:tty57
PM: Adding info for No Bus:tty58
PM: Adding info for No Bus:tty59
PM: Adding info for No Bus:tty60
PM: Adding info for No Bus:tty61
PM: Adding info for No Bus:tty62
PM: Adding info for No Bus:tty63
PM: Adding info for No Bus:ptmx
PM: Adding info for No Bus:hpet
PM: Adding info for No Bus:isa
PM: Adding info for No Bus:ram0
PM: Adding info for No Bus:1:0
PM: Adding info for No Bus:ram1
PM: Adding info for No Bus:1:1
PM: Adding info for No Bus:ram2
PM: Adding info for No Bus:1:2
PM: Adding info for No Bus:ram3
PM: Adding info for No Bus:1:3
PM: Adding info for No Bus:ram4
PM: Adding info for No Bus:1:4
PM: Adding info for No Bus:ram5
PM: Adding info for No Bus:1:5
PM: Adding info for No Bus:ram6
PM: Adding info for No Bus:1:6
PM: Adding info for No Bus:ram7
PM: Adding info for No Bus:1:7
PM: Adding info for No Bus:ram8
PM: Adding info for No Bus:1:8
PM: Adding info for No Bus:ram9
PM: Adding info for No Bus:1:9
PM: Adding info for No Bus:ram10
PM: Adding info for No Bus:1:10
PM: Adding info for No Bus:ram11
PM: Adding info for No Bus:1:11
PM: Adding info for No Bus:ram12
PM: Adding info for No Bus:1:12
PM: Adding info for No Bus:ram13
PM: Adding info for No Bus:1:13
PM: Adding info for No Bus:ram14
PM: Adding info for No Bus:1:14
PM: Adding info for No Bus:ram15
PM: Adding info for No Bus:1:15
brd: module loaded
PNP: No PS/2 controller found. Probing ports directly.
PM: Adding info for platform:i8042
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
PM: Adding info for serio:serio0
PM: Adding info for serio:serio1
PM: Adding info for No Bus:mice
PM: Adding info for No Bus:psaux
mice: PS/2 mouse device common for all mice
PM: Adding info for platform:eisa.0
EISA: Probing bus 0 at eisa.0
PM: Removing info for platform:eisa.0
cpuidle: using governor ladder
TCP cubic registered
Using IPI No-Shortcut mode
PM: Adding info for No Bus:cpu_dma_latency
PM: Adding info for No Bus:network_latency
PM: Adding info for No Bus:network_throughput
PM: Checking image partition /dev/hda6
PM: Resume from disk failed.
Magic number: 14:777:582
pci_bus 0000:03: hash matches
pcieport 0000:00:06.0: hash matches
pci_link PNP0C0F:25: hash matches
Freeing unused kernel memory: 404k freed
NET: Registered protocol family 1
PM: Adding info for No Bus:cooling_device0
fan PNP0C0B:00: registered as cooling_device0
ACPI: Fan [FAN] (on)
PM: Adding info for No Bus:thermal_zone0
thermal LNXTHERM:01: registered as thermal_zone0
ACPI: Thermal Zone [THRM] (40 C)
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
SCSI subsystem initialized
Uniform Multi-Platform E-IDE driver
ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16
ohci1394 0000:06:06.0: PCI INT A -> Link[APC1] -> GSI 16 (level, low) -> IRQ 16
PM: Adding info for ieee1394:fw-host0
PM: Adding info for No Bus:fw-host0
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci_hcd: block sizes: ed 64 td 64
ACPI: PCI Interrupt Link [APCF] enabled at IRQ 23
ohci_hcd 0000:00:0b.0: PCI INT A -> Link[APCF] -> GSI 23 (level, low) -> IRQ 23
ohci_hcd 0000:00:0b.0: setting latency timer to 64
ohci_hcd 0000:00:0b.0: OHCI Host Controller
drivers/usb/core/inode.c: creating file 'devices'
drivers/usb/core/inode.c: creating file '001'
ohci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:0b.0: created debug files
ohci_hcd 0000:00:0b.0: supports USB remote wakeup
ohci_hcd 0000:00:0b.0: irq 23, io mem 0xd5006000
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Warning! ehci_hcd should always be loaded before uhci_hcd and ohci_hcd, not after
ehci_hcd: block sizes: qh 60 qtd 96 itd 160 sitd 96
libata version 3.00 loaded.
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[16] MMIO=[d4001000-d40017ff] Max Packet=[2] IR/IT contexts=[4/8]
ohci_hcd 0000:00:0b.0: OHCI controller state
ohci_hcd 0000:00:0b.0: OHCI 1.0, NO legacy support registers
ohci_hcd 0000:00:0b.0: control 0x683 RWE RWC HCFS=operational CBSR=3
ohci_hcd 0000:00:0b.0: cmdstatus 0x00000 SOC=0
ohci_hcd 0000:00:0b.0: intrstatus 0x00000044 RHSC SF
ohci_hcd 0000:00:0b.0: intrenable 0x8000000a MIE RD WDH
ohci_hcd 0000:00:0b.0: hcca frame #0003
ohci_hcd 0000:00:0b.0: roothub.a 01000208 POTPGT=1 NPS NDP=8(8)
ohci_hcd 0000:00:0b.0: roothub.b 00000000 PPCM=0000 DR=0000
ohci_hcd 0000:00:0b.0: roothub.status 00008000 DRWE
ohci_hcd 0000:00:0b.0: roothub.portstatus [0] 0x00010301 CSC LSDA PPS CCS
ohci_hcd 0000:00:0b.0: roothub.portstatus [1] 0x00010101 CSC PPS CCS
ohci_hcd 0000:00:0b.0: roothub.portstatus [2] 0x00010101 CSC PPS CCS
ohci_hcd 0000:00:0b.0: roothub.portstatus [3] 0x00000100 PPS
ohci_hcd 0000:00:0b.0: roothub.portstatus [4] 0x00000100 PPS
ohci_hcd 0000:00:0b.0: roothub.portstatus [5] 0x00010101 CSC PPS CCS
ohci_hcd 0000:00:0b.0: roothub.portstatus [6] 0x00000100 PPS
ohci_hcd 0000:00:0b.0: roothub.portstatus [7] 0x00000100 PPS
usb usb1: default language 0x0409
usb usb1: udev 1, busnum 1, minor = 0
usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: OHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.32testing ohci_hcd
usb usb1: SerialNumber: 0000:00:0b.0
PM: Adding info for usb:usb1
usb usb1: uevent
usb usb1: usb_probe_device
usb usb1: configuration #1 chosen from 1 choice
usb usb1: adding 1-0:1.0 (config #1, interface 0)
PM: Adding info for usb:1-0:1.0
usb 1-0:1.0: uevent
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: no power switching (usb 1.0)
hub 1-0:1.0: global over-current protection
hub 1-0:1.0: power on to power good time: 2ms
hub 1-0:1.0: local power source is good
hub 1-0:1.0: no over-current condition exists
hub 1-0:1.0: trying to enable port power on non-switchable hub
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev1.1
drivers/usb/core/inode.c: creating file '001'
PM: Adding info for No Bus:ep_00
ACPI: PCI Interrupt Link [APCL] enabled at IRQ 22
ehci_hcd 0000:00:0b.1: PCI INT B -> Link[APCL] -> GSI 22 (level, low) -> IRQ 22
ehci_hcd 0000:00:0b.1: setting latency timer to 64
ehci_hcd 0000:00:0b.1: EHCI Host Controller
drivers/usb/core/inode.c: creating file '002'
ehci_hcd 0000:00:0b.1: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:0b.1: reset hcs_params 0x101888 dbg=1 cc=1 pcc=8 !ppc ports=8
ehci_hcd 0000:00:0b.1: reset portroute 0 0 0 0 0 0 0 0
ehci_hcd 0000:00:0b.1: reset hcc_params a086 caching frame 256/512/1024 park
ehci_hcd 0000:00:0b.1: park 0
ehci_hcd 0000:00:0b.1: debug port 1
ehci_hcd 0000:00:0b.1: reset command 080b02 park=3 ithresh=8 period=1024 Reset HALT
ehci_hcd 0000:00:0b.1: cache line size of 32 is not supported
ehci_hcd 0000:00:0b.1: supports USB remote wakeup
ehci_hcd 0000:00:0b.1: irq 22, io mem 0xd5007000
ehci_hcd 0000:00:0b.1: reset command 080b02 park=3 ithresh=8 period=1024 Reset HALT
ehci_hcd 0000:00:0b.1: init command 010009 (park)=0 ithresh=1 period=256 RUN
usb usb1: uevent
usb usb1: uevent
ohci1394: fw-host0: Serial EEPROM has suspicious values, attempting to set max_packet_size to 512 bytes
r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
ehci_hcd 0000:00:0b.1: USB 2.0 started, EHCI 1.00
usb usb2: default language 0x0409
usb usb2: udev 1, busnum 2, minor = 128
usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: EHCI Host Controller
ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17
r8169 0000:06:07.0: PCI INT A -> Link[APC2] -> GSI 17 (level, low) -> IRQ 17
r8169 0000:06:07.0: no PCI Express capability
PM: Adding info for No Bus:eth0
eth0: RTL8169sb/8110sb at 0xf8d46000, 00:14:d1:1a:ac:15, XID 10000000 IRQ 17
usb usb2: Manufacturer: Linux 2.6.32testing ehci_hcd
usb usb2: SerialNumber: 0000:00:0b.1
PM: Adding info for usb:usb2
usb usb2: uevent
usb usb2: usb_probe_device
usb usb2: configuration #1 chosen from 1 choice
usb usb2: adding 2-0:1.0 (config #1, interface 0)
PM: Adding info for usb:2-0:1.0
usb 2-0:1.0: uevent
hub 2-0:1.0: usb_probe_interface
hub 2-0:1.0: usb_probe_interface - got id
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 8 ports detected
hub 2-0:1.0: standalone hub
hub 2-0:1.0: no power switching (usb 1.0)
hub 2-0:1.0: individual port over-current protection
hub 2-0:1.0: power on to power good time: 20ms
hub 2-0:1.0: local power source is good
hub 2-0:1.0: trying to enable port power on non-switchable hub
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev2.1
drivers/usb/core/inode.c: creating file '001'
PM: Adding info for No Bus:ep_00
amd74xx 0000:00:0d.0: UDMA133 controller
amd74xx 0000:00:0d.0: IDE controller (0x10de:0x0265 rev 0xa1)
amd74xx 0000:00:0d.0: IDE port disabled
amd74xx 0000:00:0d.0: BIOS didn't set cable bits correctly. Enabling workaround.
amd74xx 0000:00:0d.0: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xf008-0xf00f
Probing IDE interface ide0...
usb usb2: uevent
usb usb2: uevent
udev: renamed network interface eth0 to eth1
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00010300 CSC LSDA PPS
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [1] = 0x00010100 CSC PPS
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [2] = 0x00010100 CSC PPS
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [5] = 0x00010100 CSC PPS
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 2-0:1.0: port 1: status 0501 change 0001
ehci_hcd 0000:00:0b.1: GetStatus port 2 status 001803 POWER sig=j CSC CONNECT
hub 2-0:1.0: port 2: status 0501 change 0001
ehci_hcd 0000:00:0b.1: GetStatus port 3 status 001803 POWER sig=j CSC CONNECT
hub 2-0:1.0: port 3: status 0501 change 0001
ehci_hcd 0000:00:0b.1: GetStatus port 6 status 001803 POWER sig=j CSC CONNECT
hub 2-0:1.0: port 6: status 0501 change 0001
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0000
hub 2-0:1.0: state 7 ports 8 chg 004e evt 0000
hub 2-0:1.0: port 1, status 0501, change 0000, 480 Mb/s
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 2-0:1.0: port 2, status 0501, change 0000, 480 Mb/s
ehci_hcd 0000:00:0b.1: port 2 high speed
ehci_hcd 0000:00:0b.1: GetStatus port 2 status 001005 POWER sig=se0 PE CONNECT
usb 2-2: new high speed USB device using ehci_hcd and address 3
ehci_hcd 0000:00:0b.1: port 2 high speed
ehci_hcd 0000:00:0b.1: GetStatus port 2 status 001005 POWER sig=se0 PE CONNECT
usb 2-2: default language 0x0409
ehci_hcd 0000:00:0b.1: detected XactErr len 0/8 retry 1
ehci_hcd 0000:00:0b.1: detected XactErr len 0/8 retry 1
usb 2-2: udev 3, busnum 2, minor = 130
usb 2-2: New USB device found, idVendor=058f, idProduct=6362
usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-2: Product: Mass Storage Device
usb 2-2: Manufacturer: Generic
usb 2-2: SerialNumber: 058F312D81B
PM: Adding info for usb:2-2
usb 2-2: uevent
usb 2-2: usb_probe_device
usb 2-2: configuration #1 chosen from 1 choice
usb 2-2: adding 2-2:1.0 (config #1, interface 0)
PM: Adding info for usb:2-2:1.0
usb 2-2:1.0: uevent
PM: Adding info for No Bus:ep_01
PM: Adding info for No Bus:ep_82
PM: Adding info for No Bus:usbdev2.3
drivers/usb/core/inode.c: creating file '003'
PM: Adding info for No Bus:ep_00
hub 2-0:1.0: port 3, status 0501, change 0000, 480 Mb/s
usb 2-2: uevent
usb 2-2: uevent
Initializing USB Mass Storage driver...
usb-storage 2-2:1.0: usb_probe_interface
usb-storage 2-2:1.0: usb_probe_interface - got id
scsi0 : SCSI emulation for USB Mass Storage devices
PM: Adding info for scsi:host0
PM: Adding info for No Bus:host0
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
ehci_hcd 0000:00:0b.1: port 3 high speed
ehci_hcd 0000:00:0b.1: GetStatus port 3 status 001005 POWER sig=se0 PE CONNECT
usb 2-3: new high speed USB device using ehci_hcd and address 4
ehci_hcd 0000:00:0b.1: port 3 high speed
ehci_hcd 0000:00:0b.1: GetStatus port 3 status 001005 POWER sig=se0 PE CONNECT
hda: PIONEER DVD-RW DVR-111D, ATAPI CD/DVD-ROM drive
usb 2-3: default language 0x0409
usb 2-3: udev 4, busnum 2, minor = 131
usb 2-3: New USB device found, idVendor=05e3, idProduct=0605
usb 2-3: New USB device strings: Mfr=0, Product=1, SerialNumber=0
usb 2-3: Product: USB2.0 Hub
PM: Adding info for usb:2-3
usb 2-3: uevent
usb 2-3: usb_probe_device
usb 2-3: configuration #1 chosen from 1 choice
usb 2-3: adding 2-3:1.0 (config #1, interface 0)
PM: Adding info for usb:2-3:1.0
usb 2-3:1.0: uevent
hub 2-3:1.0: usb_probe_interface
hub 2-3:1.0: usb_probe_interface - got id
hub 2-3:1.0: USB hub found
hub 2-3:1.0: 4 ports detected
hub 2-3:1.0: standalone hub
hub 2-3:1.0: individual port power switching
hub 2-3:1.0: individual port over-current protection
hub 2-3:1.0: Single TT
hub 2-3:1.0: TT requires at most 32 FS bit times (2664 ns)
hub 2-3:1.0: Port indicators are supported
hub 2-3:1.0: power on to power good time: 100ms
usb 2-3: uevent
hub 2-3:1.0: local power source is good
hub 2-3:1.0: enabling power on all ports
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev2.4
drivers/usb/core/inode.c: creating file '004'
PM: Adding info for No Bus:ep_00
hub 2-0:1.0: port 6, status 0501, change 0000, 480 Mb/s
usb 2-3: uevent
ehci_hcd 0000:00:0b.1: port 6 high speed
ehci_hcd 0000:00:0b.1: GetStatus port 6 status 001005 POWER sig=se0 PE CONNECT
hub 2-3:1.0: port 1: status 0101 change 0001
usb 2-6: new high speed USB device using ehci_hcd and address 5
ehci_hcd 0000:00:0b.1: port 6 high speed
ehci_hcd 0000:00:0b.1: GetStatus port 6 status 001005 POWER sig=se0 PE CONNECT
usb 2-3: link qh256-0001/c1ce0080 start 1 [1/0 us]
usb 2-6: udev 5, busnum 2, minor = 132
usb 2-6: New USB device found, idVendor=0409, idProduct=0059
usb 2-6: New USB device strings: Mfr=0, Product=0, SerialNumber=0
PM: Adding info for usb:2-6
usb 2-6: uevent
usb 2-6: usb_probe_device
usb 2-6: configuration #1 chosen from 1 choice
usb 2-6: adding 2-6:1.0 (config #1, interface 0)
PM: Adding info for usb:2-6:1.0
usb 2-6:1.0: uevent
hub 2-6:1.0: usb_probe_interface
hub 2-6:1.0: usb_probe_interface - got id
hub 2-6:1.0: USB hub found
hub 2-6:1.0: 4 ports detected
hub 2-6:1.0: standalone hub
hub 2-6:1.0: individual port power switching
hub 2-6:1.0: individual port over-current protection
hub 2-6:1.0: Single TT
hub 2-6:1.0: TT requires at most 16 FS bit times (1332 ns)
hub 2-6:1.0: Port indicators are supported
hub 2-6:1.0: power on to power good time: 100ms
hub 2-6:1.0: local power source is good
hub 2-6:1.0: enabling power on all ports
usb 2-6: uevent
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev2.5
drivers/usb/core/inode.c: creating file '005'
PM: Adding info for No Bus:ep_00
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00010301 CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0001, 1.5 Mb/s
usb 2-6: uevent
hub 2-6:1.0: port 1: status 0301 change 0001
hub 2-6:1.0: port 3: status 0101 change 0001
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130301 PRSC PESC CSC LSDA PPS CCS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-3:1.0: state 7 ports 4 chg 0002 evt 0000
hub 2-3:1.0: port 1, status 0101, change 0000, 12 Mb/s
usb 2-6: link qh256-0001/c1ce0340 start 2 [1/0 us]
usb 2-3.1: new high speed USB device using ehci_hcd and address 6
usb 2-3.1: udev 6, busnum 2, minor = 133
usb 2-3.1: New USB device found, idVendor=0409, idProduct=0059
usb 2-3.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
PM: Adding info for usb:2-3.1
usb 2-3.1: uevent
usb 2-3.1: usb_probe_device
usb 2-3.1: configuration #1 chosen from 1 choice
usb 2-3.1: adding 2-3.1:1.0 (config #1, interface 0)
PM: Adding info for usb:2-3.1:1.0
usb 2-3.1:1.0: uevent
hub 2-3.1:1.0: usb_probe_interface
hub 2-3.1:1.0: usb_probe_interface - got id
hub 2-3.1:1.0: USB hub found
hub 2-3.1:1.0: 4 ports detected
hub 2-3.1:1.0: standalone hub
hub 2-3.1:1.0: individual port power switching
hub 2-3.1:1.0: individual port over-current protection
hub 2-3.1:1.0: Single TT
hub 2-3.1:1.0: TT requires at most 16 FS bit times (1332 ns)
hub 2-3.1:1.0: Port indicators are supported
hub 2-3.1:1.0: power on to power good time: 100ms
hub 2-3.1:1.0: local power source is good
hub 2-3.1:1.0: enabling power on all ports
usb 2-3.1: uevent
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev2.6
drivers/usb/core/inode.c: creating file '006'
PM: Adding info for No Bus:ep_00
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
usb 2-3.1: uevent
PM: Adding info for ieee1394:001106000000bd66
PM: Adding info for No Bus:001106000000bd66
ieee1394: Host added: ID:BUS[0-00:1023] GUID[001106000000bd66]
PM: Adding info for ieee1394:001a66fffee31809
PM: Adding info for No Bus:001a66fffee31809
ieee1394: Node added: ID:BUS[0-01:1023] GUID[001a66fffee31809]
PM: Adding info for ieee1394:001a66fffee31809-0
PM: Adding info for No Bus:001a66fffee31809-0
PM: Adding info for ieee1394:001a66fffee31809-1
PM: Adding info for No Bus:001a66fffee31809-1
PM: Adding info for No Bus:ide0
PM: Adding info for No Bus:ide0
hda: host max PIO5 wanted PIO255(auto-tune) selected PIO4
hda: UDMA/66 mode selected
ide0 at 0x170-0x177,0x376 on irq 15
PM: Adding info for ide:0.0
sata_nv 0000:00:0e.0: version 3.5
ACPI: PCI Interrupt Link [APSI] enabled at IRQ 21
sata_nv 0000:00:0e.0: PCI INT A -> Link[APSI] -> GSI 21 (level, low) -> IRQ 21
sata_nv 0000:00:0e.0: Using SWNCQ mode
sata_nv 0000:00:0e.0: setting latency timer to 64
scsi1 : sata_nv
PM: Adding info for scsi:host1
PM: Adding info for No Bus:host1
scsi2 : sata_nv
PM: Adding info for scsi:host2
PM: Adding info for No Bus:host2
ata1: SATA max UDMA/133 cmd 0x9f0 ctl 0xbf0 bmdma 0xd400 irq 21
ata2: SATA max UDMA/133 cmd 0x970 ctl 0xb70 bmdma 0xd408 irq 21
ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 20
sata_nv 0000:00:0f.0: PCI INT A -> Link[APSJ] -> GSI 20 (level, low) -> IRQ 20
sata_nv 0000:00:0f.0: Using SWNCQ mode
sata_nv 0000:00:0f.0: setting latency timer to 64
scsi3 : sata_nv
PM: Adding info for scsi:host3
PM: Adding info for No Bus:host3
scsi4 : sata_nv
PM: Adding info for scsi:host4
PM: Adding info for No Bus:host4
ata3: SATA max UDMA/133 cmd 0x9e0 ctl 0xbe0 bmdma 0xe800 irq 20
ata4: SATA max UDMA/133 cmd 0x960 ctl 0xb60 bmdma 0xe808 irq 20
hub 2-3.1:1.0: port 1: status 0301 change 0001
hub 2-3.1:1.0: port 2: status 0101 change 0001
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130301 PRSC PESC CSC LSDA PPS CCS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-6:1.0: state 7 ports 4 chg 000a evt 0000
hub 2-6:1.0: port 1, status 0301, change 0000, 1.5 Mb/s
hub 2-6:1.0: port 1 not reset yet, waiting 10ms
usb 2-3.1: link qh256-0001/c1ce0a80 start 3 [1/0 us]
usb 2-6.1: new low speed USB device using ehci_hcd and address 7
hub 2-6:1.0: port 1 not reset yet, waiting 10ms
usb 2-6.1: skipped 1 descriptor after interface
usb 2-6.1: default language 0x0409
usb 2-6.1: udev 7, busnum 2, minor = 134
usb 2-6.1: New USB device found, idVendor=2222, idProduct=3100
usb 2-6.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 2-6.1: Product: Macally ECOMouse
usb 2-6.1: Manufacturer: Macally Peripherals
PM: Adding info for usb:2-6.1
usb 2-6.1: uevent
usb 2-6.1: usb_probe_device
usb 2-6.1: configuration #1 chosen from 1 choice
usb 2-6.1: adding 2-6.1:1.0 (config #1, interface 0)
PM: Adding info for usb:2-6.1:1.0
usb 2-6.1:1.0: uevent
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev2.7
drivers/usb/core/inode.c: creating file '007'
PM: Adding info for No Bus:ep_00
usb 2-6.1: uevent
hub 2-6:1.0: port 3, status 0101, change 0000, 12 Mb/s
usb 2-6.1: uevent
usbcore: registered new interface driver hiddev
usbhid 2-6.1:1.0: usb_probe_interface
usbhid 2-6.1:1.0: usb_probe_interface - got id
PM: Adding info for hid:0003:2222:3100.0001
PM: Adding info for No Bus:input0
input: Macally Peripherals Macally ECOMouse as /devices/pci0000:00/0000:00:0b.1/usb2/2-6/2-6.1/2-6.1:1.0/input/input0
PM: Adding info for No Bus:mouse0
generic-usb 0003:2222:3100.0001: input: USB HID v1.00 Mouse [Macally Peripherals Macally ECOMouse ] on usb-0000:00:0b.1-6.1/input0
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
hub 2-6:1.0: port 3 not reset yet, waiting 10ms
ata3: SATA link down (SStatus 0 SControl 300)
usb 2-6.3: new full speed USB device using ehci_hcd and address 8
hub 2-6:1.0: port 3 not reset yet, waiting 10ms
usb 2-6.3: ep0 maxpacket = 8
usb 2-6.3: default language 0x0409
usb 2-6.3: udev 8, busnum 2, minor = 135
usb 2-6.3: New USB device found, idVendor=05e3, idProduct=0604
usb 2-6.3: New USB device strings: Mfr=0, Product=1, SerialNumber=0
usb 2-6.3: Product: USB Hub
PM: Adding info for usb:2-6.3
usb 2-6.3: uevent
usb 2-6.3: usb_probe_device
usb 2-6.3: configuration #1 chosen from 1 choice
usb 2-6.3: adding 2-6.3:1.0 (config #1, interface 0)
PM: Adding info for usb:2-6.3:1.0
usb 2-6.3:1.0: uevent
hub 2-6.3:1.0: usb_probe_interface
hub 2-6.3:1.0: usb_probe_interface - got id
hub 2-6.3:1.0: USB hub found
usb 2-6.3: uevent
hub 2-6.3:1.0: 4 ports detected
hub 2-6.3:1.0: standalone hub
hub 2-6.3:1.0: individual port power switching
hub 2-6.3:1.0: individual port over-current protection
hub 2-6.3:1.0: power on to power good time: 100ms
hub 2-6.3:1.0: local power source is good
hub 2-6.3:1.0: enabling power on all ports
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev2.8
drivers/usb/core/inode.c: creating file '008'
PM: Adding info for No Bus:ep_00
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
usb 2-6.3: uevent
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
hub 2-6.3:1.0: port 3: status 0301 change 0001
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ata1.00: ATA-7: SAMSUNG SP2504C, VT100-41, max UDMA7
ata1.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata1.00: configured for UDMA/133
scsi 1:0:0:0: Direct-Access ATA SAMSUNG SP2504C VT10 PQ: 0 ANSI: 5
PM: Adding info for scsi:target1:0:0
PM: Adding info for scsi:1:0:0:0
PM: Adding info for No Bus:1:0:0:0
PM: Adding info for No Bus:1:0:0:0
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-3.1:1.0: state 7 ports 4 chg 0006 evt 0000
hub 2-3.1:1.0: port 1, status 0301, change 0000, 1.5 Mb/s
hub 2-3.1:1.0: port 1 not reset yet, waiting 10ms
usb 2-6.3: link qh128-0e01/c213e400 start 4 [1/2 us]
usb 2-3.1.1: new low speed USB device using ehci_hcd and address 9
hub 2-3.1:1.0: port 1 not reset yet, waiting 10ms
usb 2-3.1.1: skipped 1 descriptor after interface
usb 2-3.1.1: skipped 1 descriptor after interface
usb 2-3.1.1: default language 0x0409
usb 2-3.1.1: udev 9, busnum 2, minor = 136
usb 2-3.1.1: New USB device found, idVendor=10d5, idProduct=0004
usb 2-3.1.1: New USB device strings: Mfr=0, Product=2, SerialNumber=0
usb 2-3.1.1: Product: PS2 to USB AdapterA3
PM: Adding info for usb:2-3.1.1
usb 2-3.1.1: uevent
usb 2-3.1.1: usb_probe_device
usb 2-3.1.1: configuration #1 chosen from 1 choice
usb 2-3.1.1: uevent
usb 2-3.1.1: adding 2-3.1.1:1.0 (config #1, interface 0)
PM: Adding info for usb:2-3.1.1:1.0
usb 2-3.1.1:1.0: uevent
usbhid 2-3.1.1:1.0: usb_probe_interface
usbhid 2-3.1.1:1.0: usb_probe_interface - got id
PM: Adding info for hid:0003:10D5:0004.0002
PM: Adding info for No Bus:input1
input: PS2 to USB AdapterA3 as /devices/pci0000:00/0000:00:0b.1/usb2/2-3/2-3.1/2-3.1.1/2-3.1.1:1.0/input/input1
usb 2-3.1.1: link qh8-0e01/c213e700 start 5 [1/2 us]
generic-usb 0003:10D5:0004.0002: input: USB HID v1.10 Keyboard [PS2 to USB AdapterA3] on usb-0000:00:0b.1-3.1.1/input0
PM: Adding info for No Bus:ep_81
usb 2-3.1.1: adding 2-3.1.1:1.1 (config #1, interface 1)
PM: Adding info for usb:2-3.1.1:1.1
usb 2-3.1.1:1.1: uevent
usbhid 2-3.1.1:1.1: usb_probe_interface
usbhid 2-3.1.1:1.1: usb_probe_interface - got id
PM: Adding info for hid:0003:10D5:0004.0003
PM: Adding info for No Bus:input2
input: PS2 to USB AdapterA3 as /devices/pci0000:00/0000:00:0b.1/usb2/2-3/2-3.1/2-3.1.1/2-3.1.1:1.1/input/input2
usb 2-3.1.1: link qh8-0e01/c213e7c0 start 6 [1/2 us]
PM: Adding info for No Bus:mouse1
generic-usb 0003:10D5:0004.0003: input: USB HID v1.10 Mouse [PS2 to USB AdapterA3] on usb-0000:00:0b.1-3.1.1/input1
PM: Adding info for No Bus:ep_82
PM: Adding info for No Bus:usbdev2.9
drivers/usb/core/inode.c: creating file '009'
PM: Adding info for No Bus:ep_00
usb 2-3.1.1: uevent
hub 2-3.1:1.0: port 2, status 0101, change 0000, 12 Mb/s
hub 2-3.1:1.0: port 2 not reset yet, waiting 10ms
usb 2-3.1.2: new high speed USB device using ehci_hcd and address 10
hub 2-3.1:1.0: port 2 not reset yet, waiting 10ms
usb 2-3.1.2: default language 0x0409
usb 2-3.1.2: udev 10, busnum 2, minor = 137
usb 2-3.1.2: New USB device found, idVendor=05e3, idProduct=0605
usb 2-3.1.2: New USB device strings: Mfr=0, Product=1, SerialNumber=0
usb 2-3.1.2: Product: USB2.0 Hub
PM: Adding info for usb:2-3.1.2
usb 2-3.1.2: uevent
usb 2-3.1.2: usb_probe_device
usb 2-3.1.2: configuration #1 chosen from 1 choice
usb 2-3.1.2: adding 2-3.1.2:1.0 (config #1, interface 0)
PM: Adding info for usb:2-3.1.2:1.0
usb 2-3.1.2:1.0: uevent
hub 2-3.1.2:1.0: usb_probe_interface
hub 2-3.1.2:1.0: usb_probe_interface - got id
hub 2-3.1.2:1.0: USB hub found
hub 2-3.1.2:1.0: 4 ports detected
hub 2-3.1.2:1.0: standalone hub
hub 2-3.1.2:1.0: individual port power switching
hub 2-3.1.2:1.0: individual port over-current protection
hub 2-3.1.2:1.0: Single TT
hub 2-3.1.2:1.0: TT requires at most 32 FS bit times (2664 ns)
hub 2-3.1.2:1.0: Port indicators are supported
hub 2-3.1.2:1.0: power on to power good time: 100ms
usb 2-3.1.2: uevent
hub 2-3.1.2:1.0: local power source is good
hub 2-3.1.2:1.0: enabling power on all ports
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev2.10
drivers/usb/core/inode.c: creating file '010'
PM: Adding info for No Bus:ep_00
hub 2-6:1.0: state 7 ports 4 chg 0000 evt 0002
usb 2-3.1.2: uevent
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030300 PESC CSC LSDA PPS
hub 1-0:1.0: port 1, status 0300, change 0003, 1.5 Mb/s
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
hub 2-3.1.2:1.0: port 1: status 0101 change 0001
hub 2-3.1.2:1.0: port 2: status 0301 change 0001
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x300
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 2-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
ata2.00: ATA-7: ST3250620AS, 3.AAC, max UDMA/133
ata2.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32)
usb 2-3.1.2: link qh256-0001/c213e900 start 7 [1/0 us]
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ata2.00: configured for UDMA/133
scsi 2:0:0:0: Direct-Access ATA ST3250620AS 3.AA PQ: 0 ANSI: 5
PM: Adding info for scsi:target2:0:0
PM: Adding info for scsi:2:0:0:0
PM: Adding info for No Bus:2:0:0:0
PM: Adding info for No Bus:2:0:0:0
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 2-6.3:1.0: state 7 ports 4 chg 0008 evt 0000
hub 2-6.3:1.0: port 3, status 0301, change 0000, 1.5 Mb/s
usb 2-6.3.3: new low speed USB device using ehci_hcd and address 12
hub 2-6.3:1.0: port 3 not reset yet, waiting 10ms
usb 2-6.3.3: skipped 1 descriptor after interface
usb 2-6.3.3: skipped 1 descriptor after interface
usb 2-6.3.3: default language 0x0409
usb 2-6.3.3: udev 12, busnum 2, minor = 139
usb 2-6.3.3: New USB device found, idVendor=2222, idProduct=0013
usb 2-6.3.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 2-6.3.3: Product: Macally iKeySlim
usb 2-6.3.3: Manufacturer: Macally Peripherals
PM: Adding info for usb:2-6.3.3
usb 2-6.3.3: uevent
usb 2-6.3.3: usb_probe_device
usb 2-6.3.3: configuration #1 chosen from 1 choice
usb 2-6.3.3: uevent
usb 2-6.3.3: adding 2-6.3.3:1.0 (config #1, interface 0)
PM: Adding info for usb:2-6.3.3:1.0
usb 2-6.3.3:1.0: uevent
usbhid 2-6.3.3:1.0: usb_probe_interface
usbhid 2-6.3.3:1.0: usb_probe_interface - got id
PM: Adding info for hid:0003:2222:0013.0004
generic-usb: probe of 0003:2222:0013.0004 failed with error -22
PM: Adding info for No Bus:ep_81
usb 2-6.3.3: adding 2-6.3.3:1.1 (config #1, interface 1)
PM: Adding info for usb:2-6.3.3:1.1
usb 2-6.3.3:1.1: uevent
usbhid 2-6.3.3:1.1: usb_probe_interface
usbhid 2-6.3.3:1.1: usb_probe_interface - got id
PM: Adding info for hid:0003:2222:0013.0005
PM: Adding info for No Bus:input3
input: Macally Peripherals Macally iKeySlim as /devices/pci0000:00/0000:00:0b.1/usb2/2-6/2-6.3/2-6.3.3/2-6.3.3:1.1/input/input3
usb 2-6.3.3: link qh8-0e01/c213ec80 start 0 [1/2 us]
PM: Adding info for No Bus:mouse2
generic-usb 0003:2222:0013.0005: input: USB HID v1.10 Mouse [Macally Peripherals Macally iKeySlim] on usb-0000:00:0b.1-6.3.3/input1
PM: Adding info for No Bus:ep_82
PM: Adding info for No Bus:usbdev2.12
drivers/usb/core/inode.c: creating file '012'
PM: Adding info for No Bus:ep_00
hub 2-3.1.2:1.0: state 7 ports 4 chg 0006 evt 0000
usb 2-6.3.3: uevent
hub 2-3.1.2:1.0: port 1, status 0101, change 0000, 12 Mb/s
usb 2-3.1.2.1: new high speed USB device using ehci_hcd and address 13
hub 2-3.1.2:1.0: port 1 not reset yet, waiting 10ms
usb 2-3.1.2.1: default language 0x0409
usb 2-3.1.2.1: udev 13, busnum 2, minor = 140
usb 2-3.1.2.1: New USB device found, idVendor=090c, idProduct=1000
usb 2-3.1.2.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-3.1.2.1: Product: DISK 2.0
usb 2-3.1.2.1: Manufacturer: USB
usb 2-3.1.2.1: SerialNumber: PHN84K6AD8PLXSVC
PM: Adding info for usb:2-3.1.2.1
usb 2-3.1.2.1: uevent
usb 2-3.1.2.1: usb_probe_device
usb 2-3.1.2.1: configuration #1 chosen from 1 choice
usb 2-3.1.2.1: adding 2-3.1.2.1:1.0 (config #1, interface 0)
PM: Adding info for usb:2-3.1.2.1:1.0
usb 2-3.1.2.1:1.0: uevent
usb-storage 2-3.1.2.1:1.0: usb_probe_interface
usb-storage 2-3.1.2.1:1.0: usb_probe_interface - got id
scsi5 : SCSI emulation for USB Mass Storage devices
PM: Adding info for scsi:host5
PM: Adding info for No Bus:host5
usb-storage: device found at 13
usb-storage: waiting for device to settle before scanning
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:ep_02
PM: Adding info for No Bus:usbdev2.13
drivers/usb/core/inode.c: creating file '013'
PM: Adding info for No Bus:ep_00
usb 2-3.1.2.1: uevent
hub 2-3.1.2:1.0: port 2, status 0301, change 0000, 1.5 Mb/s
usb 2-3.1.2.1: uevent
usb 2-3.1.2.2: new low speed USB device using ehci_hcd and address 14
hub 2-3.1.2:1.0: port 2 not reset yet, waiting 10ms
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: ATAPI: ATAPI iHOS104, WL08, max UDMA/100
ata4.00: configured for UDMA/100
usb 2-3.1.2.2: skipped 1 descriptor after interface
usb 2-3.1.2.2: default language 0x0409
usb 2-3.1.2.2: udev 14, busnum 2, minor = 141
usb 2-3.1.2.2: New USB device found, idVendor=046d, idProduct=c00c
usb 2-3.1.2.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 2-3.1.2.2: Product: USB Optical Mouse
usb 2-3.1.2.2: Manufacturer: Logitech
PM: Adding info for usb:2-3.1.2.2
usb 2-3.1.2.2: uevent
usb 2-3.1.2.2: usb_probe_device
usb 2-3.1.2.2: configuration #1 chosen from 1 choice
usb 2-3.1.2.2: adding 2-3.1.2.2:1.0 (config #1, interface 0)
PM: Adding info for usb:2-3.1.2.2:1.0
usb 2-3.1.2.2:1.0: uevent
usbhid 2-3.1.2.2:1.0: usb_probe_interface
usbhid 2-3.1.2.2:1.0: usb_probe_interface - got id
PM: Adding info for hid:0003:046D:C00C.0006
usb 2-3.1.2.2: uevent
PM: Adding info for No Bus:input4
input: Logitech USB Optical Mouse as /devices/pci0000:00/0000:00:0b.1/usb2/2-3/2-3.1/2-3.1.2/2-3.1.2.2/2-3.1.2.2:1.0/input/input4
PM: Adding info for No Bus:mouse3
generic-usb 0003:046D:C00C.0006: input: USB HID v1.10 Mouse [Logitech USB Optical Mouse] on usb-0000:00:0b.1-3.1.2.2/input0
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev2.14
drivers/usb/core/inode.c: creating file '014'
PM: Adding info for No Bus:ep_00
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00010301 CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0001, 1.5 Mb/s
usb 2-3.1.2.2: uevent
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-6.3:1.0: state 7 ports 4 chg 0000 evt 0008
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 2-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 2-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 2-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 2-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 2-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 2-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 2-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 2-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
scsi 0:0:0:0: Direct-Access Generic USB SD Reader 1.00 PQ: 0 ANSI: 0
PM: Adding info for scsi:target0:0:0
PM: Adding info for scsi:0:0:0:0
PM: Adding info for No Bus:0:0:0:0
PM: Adding info for No Bus:0:0:0:0
scsi 0:0:0:1: Direct-Access Generic USB CF Reader 1.01 PQ: 0 ANSI: 0
PM: Adding info for scsi:0:0:0:1
PM: Adding info for No Bus:0:0:0:1
PM: Adding info for No Bus:0:0:0:1
scsi 0:0:0:2: Direct-Access Generic USB SM Reader 1.02 PQ: 0 ANSI: 0
PM: Adding info for scsi:0:0:0:2
PM: Adding info for No Bus:0:0:0:2
PM: Adding info for No Bus:0:0:0:2
scsi 0:0:0:3: Direct-Access Generic USB MS Reader 1.03 PQ: 0 ANSI: 0
PM: Adding info for scsi:0:0:0:3
PM: Adding info for No Bus:0:0:0:3
PM: Adding info for No Bus:0:0:0:3
usb-storage: device scan complete
PM: Adding info for No Bus:1:0:0:0
PM: Adding info for No Bus:2:0:0:0
PM: Adding info for No Bus:0:0:0:0
PM: Adding info for No Bus:0:0:0:1
PM: Adding info for No Bus:0:0:0:2
PM: Adding info for No Bus:0:0:0:3
sd 1:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
PM: Adding info for No Bus:sda
sda:
sd 2:0:0:0: [sdb] 488397168 512-byte logical blocks: (250 GB/232 GiB)
sd 2:0:0:0: [sdb] Write Protect is off
sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
PM: Adding info for No Bus:sdb
sdb:
PM: Adding info for No Bus:sdc
PM: Adding info for No Bus:8:32
PM: Adding info for No Bus:sdd
PM: Adding info for No Bus:8:48
PM: Adding info for No Bus:sde
PM: Adding info for No Bus:8:64
PM: Adding info for No Bus:sdf
PM: Adding info for No Bus:8:80
sd 0:0:0:0: [sdc] Attached SCSI removable disk
sd 0:0:0:1: [sdd] Attached SCSI removable disk
sd 0:0:0:2: [sde] Attached SCSI removable disk
sd 0:0:0:3: [sdf] Attached SCSI removable disk
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
unknown partition table
PM: Adding info for No Bus:8:16
sd 2:0:0:0: [sdb] Attached SCSI disk
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
sda1 sda2 sda3 < >
PM: Adding info for No Bus:sda1
PM: Adding info for No Bus:sda2
PM: Adding info for No Bus:sda3
PM: Adding info for No Bus:8:0
sd 1:0:0:0: [sda] Attached SCSI disk
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 2-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 2-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 2-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 2-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 2-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 2-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 2-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
scsi 5:0:0:0: Direct-Access USB DISK 2.0 0403 PQ: 0 ANSI: 0 CCS
PM: Adding info for scsi:target5:0:0
PM: Adding info for scsi:5:0:0:0
PM: Adding info for No Bus:5:0:0:0
PM: Adding info for No Bus:5:0:0:0
PM: Adding info for No Bus:5:0:0:0
sd 5:0:0:0: [sdg] 3981312 512-byte logical blocks: (2.03 GB/1.89 GiB)
sd 5:0:0:0: [sdg] Write Protect is off
usb-storage: device scan complete
sd 5:0:0:0: [sdg] Mode Sense: 43 00 00 00
sd 5:0:0:0: [sdg] Assuming drive cache: write through
PM: Adding info for No Bus:sdg
sd 5:0:0:0: [sdg] Assuming drive cache: write through
sdg: sdg1
PM: Adding info for No Bus:sdg1
PM: Adding info for No Bus:8:96
sd 5:0:0:0: [sdg] Assuming drive cache: write through
sd 5:0:0:0: [sdg] Attached SCSI removable disk
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 2-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 2-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 2-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 2-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 2-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 2-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 2-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 2-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 2-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030300 PESC CSC LSDA PPS
hub 1-0:1.0: port 1, status 0300, change 0003, 1.5 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x300
ohci_hcd 0000:00:0b.0: auto-stop root hub
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for UDMA/100
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4: limiting SATA link speed to 1.5 Gbps
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for UDMA/100
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: limiting speed to UDMA/66:PIO4
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for UDMA/66
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: limiting speed to UDMA/33:PIO4
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for UDMA/33
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: limiting speed to PIO4
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO4
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: limiting speed to PIO3
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO3
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: limiting speed to PIO0
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
usb 2-2:1.0: uevent
usb 2-2: uevent
usb 2-2:1.0: uevent
usb 2-2: uevent
usb 2-2:1.0: uevent
usb 2-2: uevent
usb 2-2:1.0: uevent
usb 2-2: uevent
usb 2-2:1.0: uevent
usb 2-2:1.0: uevent
usb 2-2:1.0: uevent
usb 2-2:1.0: uevent
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
INFO: task modprobe:664 blocked for more than 120 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
modprobe D c21d5f34 0 664 1 0x00000000
c3c05700 00000086 c3c01f04 c21d5f34 c3c01f04 00000000 c12b6e12 c1c7f480
c10e29d1 c1389f04 c201b480 c201b60c 00000000 fffb9369 c3c01f20 00000000
00000001 c1d63500 c3c01f04 c201b60c c1318bf0 00000000 c1df8780 c1e49990
Call Trace:
[<c10e29d1>] ? sysfs_find_dirent+0x21/0x30
[<c10e24f5>] ? sysfs_add_file_mode+0x55/0x90
[<c104a9dd>] ? async_synchronize_cookie_domain+0xbd/0x150
[<c10445d0>] ? autoremove_wake_function+0x0/0x50
[<c104aa90>] ? async_synchronize_full+0x10/0x30
[<c105a04c>] ? sys_init_module+0xfc/0x220
[<c1003070>] ? syscall_call+0x7/0xb
INFO: task modprobe:758 blocked for more than 120 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
modprobe D c1d03f34 0 758 1 0x00000000
c3c05700 00000082 00000002 c1d03f34 c3c01f04 00000000 c1d03f2c c13066e0
c10e29d1 c1389f04 c1c7f480 c1c7f60c 00000000 fffb8ad5 00000000 00000000
00000001 c2210540 c3c01f04 c1c7f60c 000006e2 00000000 c1df8600 c1cc22a0
Call Trace:
[<c10e29d1>] ? sysfs_find_dirent+0x21/0x30
[<c10e24f5>] ? sysfs_add_file_mode+0x55/0x90
[<c1242ca9>] ? _spin_lock_irqsave+0x19/0x40
[<c1242ca9>] ? _spin_lock_irqsave+0x19/0x40
[<c104a9dd>] ? async_synchronize_cookie_domain+0xbd/0x150
[<c10445d0>] ? autoremove_wake_function+0x0/0x50
[<c104aa90>] ? async_synchronize_full+0x10/0x30
[<c105a04c>] ? sys_init_module+0xfc/0x220
[<c1003070>] ? syscall_call+0x7/0xb
INFO: task modprobe:893 blocked for more than 120 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
modprobe D c209df34 0 893 1 0x00000000
c3d05700 00000082 00000002 c209df34 c3d01f04 00000000 c209df5c c2018a80
c209df04 c1389f04 c1c7f100 c1c7f28c 00000001 fffb8a58 00000000 00000000
00000000 c1db8540 c3d01f04 c1c7f28c 00000000 f8ef8cd4 f8ef5580 c10e2540
Call Trace:
[<f8ef5580>] ? usbhid_probe+0x0/0x360 [usbhid]
[<c10e2540>] ? sysfs_add_file+0x10/0x20
[<c1242ca9>] ? _spin_lock_irqsave+0x19/0x40
[<c1242ca9>] ? _spin_lock_irqsave+0x19/0x40
[<c104a9dd>] ? async_synchronize_cookie_domain+0xbd/0x150
[<f8efc0c6>] ? hid_init+0xc6/0xca [usbhid]
[<c10445d0>] ? autoremove_wake_function+0x0/0x50
[<c104aa90>] ? async_synchronize_full+0x10/0x30
[<c105a04c>] ? sys_init_module+0xfc/0x220
[<c1003070>] ? syscall_call+0x7/0xb
INFO: task modprobe:913 blocked for more than 120 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
modprobe D c1e09f34 0 913 1 0x00000000
c3d05700 00000082 00000002 c1e09f34 c3d01f04 00000000 c1e09f2c c201aa00
000080d0 c1389f04 c2018a80 c2018c0c 00000001 fffb8ad4 00000000 00000000
00000202 c1d63340 c3d01f04 c2018c0c 00000632 c213efc0 00000002 c106a750
Call Trace:
[<c106a750>] ? mempool_alloc_slab+0x0/0x10
[<c106a760>] ? mempool_free_slab+0x0/0x10
[<c1242ca9>] ? _spin_lock_irqsave+0x19/0x40
[<c1242ca9>] ? _spin_lock_irqsave+0x19/0x40
[<c104a9dd>] ? async_synchronize_cookie_domain+0xbd/0x150
[<f8fec13a>] ? init_sd+0x13a/0x17a [sd_mod]
[<c10445d0>] ? autoremove_wake_function+0x0/0x50
[<c104aa90>] ? async_synchronize_full+0x10/0x30
[<c105a04c>] ? sys_init_module+0xfc/0x220
[<c1003070>] ? syscall_call+0x7/0xb
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
INFO: task modprobe:664 blocked for more than 120 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
modprobe D c21d5f34 0 664 1 0x00000000
c3c05700 00000086 c3c01f04 c21d5f34 c3c01f04 00000000 c12b6e12 c1c7f480
c10e29d1 c1389f04 c201b480 c201b60c 00000000 fffb9369 c3c01f20 00000000
00000001 c1d63500 c3c01f04 c201b60c c1318bf0 00000000 c1df8780 c1e49990
Call Trace:
[<c10e29d1>] ? sysfs_find_dirent+0x21/0x30
[<c10e24f5>] ? sysfs_add_file_mode+0x55/0x90
[<c104a9dd>] ? async_synchronize_cookie_domain+0xbd/0x150
[<c10445d0>] ? autoremove_wake_function+0x0/0x50
[<c104aa90>] ? async_synchronize_full+0x10/0x30
[<c105a04c>] ? sys_init_module+0xfc/0x220
[<c1003070>] ? syscall_call+0x7/0xb
INFO: task modprobe:758 blocked for more than 120 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
modprobe D c1d03f34 0 758 1 0x00000000
c3c05700 00000082 00000002 c1d03f34 c3c01f04 00000000 c1d03f2c c13066e0
c10e29d1 c1389f04 c1c7f480 c1c7f60c 00000000 fffb8ad5 00000000 00000000
00000001 c2210540 c3c01f04 c1c7f60c 000006e2 00000000 c1df8600 c1cc22a0
Call Trace:
[<c10e29d1>] ? sysfs_find_dirent+0x21/0x30
[<c10e24f5>] ? sysfs_add_file_mode+0x55/0x90
[<c1242ca9>] ? _spin_lock_irqsave+0x19/0x40
[<c1242ca9>] ? _spin_lock_irqsave+0x19/0x40
[<c104a9dd>] ? async_synchronize_cookie_domain+0xbd/0x150
[<c10445d0>] ? autoremove_wake_function+0x0/0x50
[<c104aa90>] ? async_synchronize_full+0x10/0x30
[<c105a04c>] ? sys_init_module+0xfc/0x220
[<c1003070>] ? syscall_call+0x7/0xb
INFO: task modprobe:893 blocked for more than 120 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
modprobe D c209df34 0 893 1 0x00000000
c3d05700 00000082 00000002 c209df34 c3d01f04 00000000 c209df5c c2018a80
c209df04 c1389f04 c1c7f100 c1c7f28c 00000001 fffb8a58 00000000 00000000
00000000 c1db8540 c3d01f04 c1c7f28c 00000000 f8ef8cd4 f8ef5580 c10e2540
Call Trace:
[<f8ef5580>] ? usbhid_probe+0x0/0x360 [usbhid]
[<c10e2540>] ? sysfs_add_file+0x10/0x20
[<c1242ca9>] ? _spin_lock_irqsave+0x19/0x40
[<c1242ca9>] ? _spin_lock_irqsave+0x19/0x40
[<c104a9dd>] ? async_synchronize_cookie_domain+0xbd/0x150
[<f8efc0c6>] ? hid_init+0xc6/0xca [usbhid]
[<c10445d0>] ? autoremove_wake_function+0x0/0x50
[<c104aa90>] ? async_synchronize_full+0x10/0x30
[<c105a04c>] ? sys_init_module+0xfc/0x220
[<c1003070>] ? syscall_call+0x7/0xb
INFO: task modprobe:913 blocked for more than 120 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
modprobe D c1e09f34 0 913 1 0x00000000
c3d05700 00000082 00000002 c1e09f34 c3d01f04 00000000 c1e09f2c c201aa00
000080d0 c1389f04 c2018a80 c2018c0c 00000001 fffb8ad4 00000000 00000000
00000202 c1d63340 c3d01f04 c2018c0c 00000632 c213efc0 00000002 c106a750
Call Trace:
[<c106a750>] ? mempool_alloc_slab+0x0/0x10
[<c106a760>] ? mempool_free_slab+0x0/0x10
[<c1242ca9>] ? _spin_lock_irqsave+0x19/0x40
[<c1242ca9>] ? _spin_lock_irqsave+0x19/0x40
[<c104a9dd>] ? async_synchronize_cookie_domain+0xbd/0x150
[<f8fec13a>] ? init_sd+0x13a/0x17a [sd_mod]
[<c10445d0>] ? autoremove_wake_function+0x0/0x50
[<c104aa90>] ? async_synchronize_full+0x10/0x30
[<c105a04c>] ? sys_init_module+0xfc/0x220
[<c1003070>] ? syscall_call+0x7/0xb
INFO: task modprobe:924 blocked for more than 120 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
modprobe D c2129f34 0 924 625 0x00000000
c3c05700 00000086 00000002 c2129f34 c3c01f04 00000000 f8ff76e4 0000002d
f902f4c4 c1389f04 c1c7f800 c1c7f98c 00000000 fffe32c5 00000000 c1305ef8
00000202 c1db96c0 c3c01f04 c1c7f98c f9039ac0 00000000 c10363f1 f9039b40
Call Trace:
[<c10363f1>] ? sysctl_set_parent+0x21/0x40
[<c1242f2c>] ? _spin_unlock+0xc/0x30
[<c1037b44>] ? __register_sysctl_paths+0x1f4/0x2e0
[<c104a9dd>] ? async_synchronize_cookie_domain+0xbd/0x150
[<c10445d0>] ? autoremove_wake_function+0x0/0x50
[<c104aa90>] ? async_synchronize_full+0x10/0x30
[<c105a04c>] ? sys_init_module+0xfc/0x220
[<c1003070>] ? syscall_call+0x7/0xb
usb 2-3.1.2.1:1.0: uevent
usb 2-3.1.2.1: uevent
usb 2-3.1.2.1:1.0: uevent
usb 2-3.1.2.1:1.0: uevent
usb 2-3.1.2.1: uevent
usb 2-3.1.2.1:1.0: uevent
PM: Adding info for No Bus:device-mapper
device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
PM: Adding info for No Bus:dm-0
PM: Adding info for No Bus:253:0
PM: Adding info for No Bus:dm-1
PM: Adding info for No Bus:253:1
PM: Adding info for No Bus:dm-2
PM: Adding info for No Bus:253:2
PM: Adding info for No Bus:dm-3
PM: Adding info for No Bus:253:3
PM: Adding info for No Bus:dm-4
PM: Adding info for No Bus:253:4
PM: Adding info for No Bus:dm-5
PM: Adding info for No Bus:253:5
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
INFO: task modprobe:664 blocked for more than 120 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
modprobe D c21d5f34 0 664 1 0x00000000
c3c05700 00000086 c3c01f04 c21d5f34 c3c01f04 00000000 c12b6e12 c1c7f480
c10e29d1 c1389f04 c201b480 c201b60c 00000000 fffb9369 c3c01f20 00000000
00000001 c1d63500 c3c01f04 c201b60c c1318bf0 00000000 c1df8780 c1e49990
Call Trace:
[<c10e29d1>] ? sysfs_find_dirent+0x21/0x30
[<c10e24f5>] ? sysfs_add_file_mode+0x55/0x90
[<c104a9dd>] ? async_synchronize_cookie_domain+0xbd/0x150
[<c10445d0>] ? autoremove_wake_function+0x0/0x50
[<c104aa90>] ? async_synchronize_full+0x10/0x30
[<c105a04c>] ? sys_init_module+0xfc/0x220
[<c1003070>] ? syscall_call+0x7/0xb
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: WARNING: synchronous SCSI scan failed without making any progress,
switching to async
md: raid0 personality registered for level 0
ata4: EH complete
ide-cd driver 5.00
PM: Adding info for No Bus:0.0
ide-cd: hda: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2000kB Cache
Uniform CD-ROM driver Revision: 3.20
md: raid1 personality registered for level 1
xor: automatically using best checksumming function: pIII_sse
pIII_sse : 7516.000 MB/sec
xor: using function: pIII_sse (7516.000 MB/sec)
PM: Adding info for No Bus:hda
PM: Adding info for No Bus:3:0
raid6: int32x1 878 MB/s
raid6: int32x2 839 MB/s
raid6: int32x4 703 MB/s
raid6: int32x8 585 MB/s
raid6: mmxx1 2742 MB/s
raid6: mmxx2 3160 MB/s
raid6: sse1x1 1886 MB/s
raid6: sse1x2 2425 MB/s
raid6: sse2x1 3535 MB/s
raid6: sse2x2 4203 MB/s
raid6: using algorithm sse2x2 (4203 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
md: raid10 personality registered for level 10
PM: Marking nosave pages: 000000000009c000 - 0000000000100000
PM: Basic memory bitmaps created
PM: Basic memory bitmaps freed
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with writeback data mode.
udev: starting version 146
usb usb1: uevent
usb 1-0:1.0: uevent
usb usb2: uevent
usb 2-0:1.0: uevent
usb 2-2: uevent
usb 2-2:1.0: uevent
usb 2-3: uevent
usb 2-3.1: uevent
usb 2-3.1.1: uevent
usb 2-3.1.1:1.0: uevent
usb 2-3.1.1:1.1: uevent
usb 2-3.1.2: uevent
usb 2-3.1.2.1: uevent
usb 2-3.1.2.1:1.0: uevent
usb 2-3.1.2.2: uevent
usb 2-3.1.2.2:1.0: uevent
usb 2-3.1.2:1.0: uevent
usb 2-3.1:1.0: uevent
usb 2-3:1.0: uevent
usb 2-6: uevent
usb 2-6.1: uevent
usb 2-6.1:1.0: uevent
usb 2-6.3: uevent
usb 2-6.3.3: uevent
usb 2-6.3.3:1.0: uevent
usb 2-6.3.3:1.1: uevent
usb 2-6.3:1.0: uevent
usb 2-6:1.0: uevent
usb usb1: uevent
usb usb2: uevent
usb usb1: uevent
usb usb2: uevent
usb 2-2: uevent
usb 2-3: uevent
usb 2-2:1.0: uevent
usb 2-2: uevent
usb 2-2:1.0: uevent
usb 2-2: uevent
usb 2-2:1.0: uevent
usb 2-2: uevent
usb 2-2: uevent
usb 2-2:1.0: uevent
usb 2-2: uevent
usb 2-3: uevent
PM: Adding info for No Bus:rtc
Real Time Clock Driver v1.12b
usb 2-6: uevent
usb 2-2:1.0: uevent
usb 2-2:1.0: uevent
usb 2-2:1.0: uevent
usb 2-2:1.0: uevent
usb 2-6: uevent
usb 2-3.1: uevent
usb 2-3.1: uevent
usb 2-6.1: uevent
usb 2-6.3: uevent
usb 2-6.1: uevent
usb 2-6.3: uevent
usb 2-3.1.1: uevent
usb 2-3.1.2: uevent
usb 2-3.1.1: uevent
usb 2-6.3.3: uevent
usb 2-3.1.2: uevent
usb 2-3.1.2.2: uevent
usb 2-6.3.3: uevent
usb 2-3.1.2.2: uevent
usb 2-3.1.2.1: uevent
usb 2-3.1.2.1:1.0: uevent
usb 2-3.1.2.1: uevent
usb 2-3.1.2.1:1.0: uevent
usb 2-3.1.2.1: uevent
ACPI: SSDT 7fefa940 00175 (v01 Nvidia ASUSACPI 42302E31 AWRD 00000000)
PM: Adding info for No Bus:cooling_device1
processor LNXCPU:00: registered as cooling_device1
ACPI: SSDT 7fefad50 000CE (v01 Nvidia ASUSACPI 42302E31 AWRD 00000000)
PM: Adding info for No Bus:cooling_device2
processor LNXCPU:01: registered as cooling_device2
PM: Adding info for No Bus:input5
input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input5
ACPI: Power Button [PWRB]
PM: Adding info for No Bus:input6
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input6
ACPI: Power Button [PWRF]
PM: Adding info for No Bus:raw1394
ieee1394: raw1394: /dev/raw1394 device initialized
PM: Adding info for No Bus:hwmon0
PM: Adding info for No Bus:event0
PM: Adding info for No Bus:event1
PM: Adding info for No Bus:event2
PM: Adding info for No Bus:event3
PM: Adding info for No Bus:event4
PM: Adding info for No Bus:event5
PM: Adding info for No Bus:event6
usb 2-3.1.2.2:1.0: uevent
usb 2-6.3.3:1.1: uevent
usb 2-3.1.2.2: uevent
usb 2-6.3.3: uevent
usb 2-3.1.2.2:1.0: uevent
usb 2-3.1.2.2: uevent
usb 2-6.3.3:1.1: uevent
usb 2-6.3.3: uevent
usb 2-3.1.2.2:1.0: uevent
usb 2-3.1.2.2:1.0: uevent
usb 2-6.3.3:1.1: uevent
usb 2-6.3.3:1.1: uevent
ACPI: I/O resource nForce2_smbus [0x5000-0x503f] conflicts with ACPI region SM00 [0x5000-0x5005]
ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
nForce2_smbus 0000:00:0a.1: Error probing SMB1.
PM: Adding info for i2c:i2c-0
i2c i2c-0: nForce2 SMBus adapter at 0x5100
usb 2-6.1:1.0: uevent
usb 2-6.1: uevent
usb 2-6.1:1.0: uevent
usb 2-6.1: uevent
usb 2-3.1.1:1.1: uevent
usb 2-3.1.1: uevent
usb 2-3.1.1:1.1: uevent
usb 2-3.1.1: uevent
usb 2-6.1:1.0: uevent
usb 2-6.1:1.0: uevent
usb 2-3.1.1:1.1: uevent
usb 2-3.1.1:1.1: uevent
PM: Adding info for No Bus:dv1394-0
usb 2-3.1.1:1.0: uevent
usb 2-3.1.1: uevent
usb 2-3.1.1:1.0: uevent
PM: Adding info for No Bus:timer
PM: Adding info for No Bus:seq
hda: UDMA/66 mode selected
hda: task_no_data_intr: status=0x41 { DriveReady Error }
hda: task_no_data_intr: error=0x04 { AbortedCommand }
hda: possibly failed opcode: 0xe3
PM: Adding info for No Bus:sequencer
PM: Adding info for No Bus:sequencer2
ACPI: PCI Interrupt Link [AAZA] enabled at IRQ 23
HDA Intel 0000:00:10.1: PCI INT B -> Link[AAZA] -> GSI 23 (level, low) -> IRQ 23
HDA Intel 0000:00:10.1: setting latency timer to 64
PM: Adding info for No Bus:input7
input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:10.1/input/input7
PM: Adding info for No Bus:event7
PM: Adding info for No Bus:card0
PM: Adding info for No Bus:pcmC0D1p
PM: Adding info for No Bus:adsp
PM: Adding info for No Bus:pcmC0D0p
PM: Adding info for No Bus:pcmC0D0c
PM: Adding info for No Bus:dsp
PM: Adding info for No Bus:audio
PM: Adding info for No Bus:hwC0D0
PM: Adding info for No Bus:controlC0
PM: Adding info for No Bus:mixer
PM: Adding info for No Bus:vcs2
PM: Adding info for No Bus:vcsa2
PM: Adding info for No Bus:vcs3
PM: Adding info for No Bus:vcsa3
PM: Adding info for No Bus:vcs4
PM: Adding info for No Bus:vcsa4
PM: Adding info for No Bus:vcs5
PM: Adding info for No Bus:vcsa5
PM: Adding info for No Bus:vcs6
PM: Adding info for No Bus:vcsa6
hda: UDMA/66 mode selected
hda: task_no_data_intr: status=0x41 { DriveReady Error }
hda: task_no_data_intr: error=0x04 { AbortedCommand }
hda: possibly failed opcode: 0xe3
EXT3 FS on dm-1, internal journal
i2c /dev entries driver
PM: Adding info for No Bus:i2c-0
it87: Found IT8712F chip at 0x290, revision 7
it87: in3 is VCC (+5V)
it87: in7 is VCCH (+5V Stand-By)
ACPI: I/O resource it87 [0x295-0x296] conflicts with ACPI region HWRE [0x295-0x296]
ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
fuse init (API version 7.13)
PM: Adding info for No Bus:fuse
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-4, internal journal
EXT3-fs: mounted filesystem with writeback data mode.
PM: Adding info for No Bus:253:2-fuseblk
PM: Adding info for No Bus:253:5-fuseblk
Adding 4194296k swap on /mnt/oldlin/4G-memory.swap. Priority:-1 extents:1057 across:4264956k
r8169: eth1: link up
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PM: Adding info for No Bus:0:16
PM: Adding info for No Bus:0:17
PM: Adding info for No Bus:0:18
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
r8169: eth1: link up
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
ata4: drained 18 bytes to clear DRQ.
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 24 00
ata4.00: cmd a0/00:00:00:24:00/00:00:00:00:00/a0 tag 0 pio 36 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO0
ata4: EH complete
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: sata_nv times out for BD-ROM iHOS104-08
2010-02-20 19:11 ` Cengiz Günay
@ 2010-02-21 1:01 ` Tejun Heo
2010-02-21 21:28 ` Cengiz Günay
0 siblings, 1 reply; 28+ messages in thread
From: Tejun Heo @ 2010-02-21 1:01 UTC (permalink / raw)
To: Cengiz Günay; +Cc: Robert Hancock, linux-kernel, linux-ide
[-- Attachment #1: Type: text/plain, Size: 452 bytes --]
On 02/21/2010 04:11 AM, Cengiz Günay wrote:
>> Does the attached patch make any difference?
>
> Not that I can tell. I still get an infinite loop of ata4 errors. I
> attached a full dmesg output with the patch. Note that I have both the
> patches disable-clear-ua and drain-from-atapi-pio-bytes applied at the
> same time.
Hmmm... So, DRQ gets cleared? That's strange. When then the 18 extra
bytes happen? Can you please try this one?
--
tejun
[-- Attachment #2: swncq-polling-pio.patch --]
[-- Type: text/x-patch, Size: 448 bytes --]
diff --git a/drivers/ata/sata_nv.c b/drivers/ata/sata_nv.c
index 0c82d33..ae63b0b 100644
--- a/drivers/ata/sata_nv.c
+++ b/drivers/ata/sata_nv.c
@@ -585,7 +585,7 @@ static const struct ata_port_info nv_port_info[] = {
/* SWNCQ */
{
.flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
- ATA_FLAG_NCQ,
+ ATA_FLAG_NCQ | ATA_FLAG_PIO_POLLING,
.pio_mask = NV_PIO_MASK,
.mwdma_mask = NV_MWDMA_MASK,
.udma_mask = NV_UDMA_MASK,
^ permalink raw reply related [flat|nested] 28+ messages in thread
* Re: sata_nv times out for BD-ROM iHOS104-08
2010-02-21 1:01 ` Tejun Heo
@ 2010-02-21 21:28 ` Cengiz Günay
2010-02-23 2:38 ` Tejun Heo
0 siblings, 1 reply; 28+ messages in thread
From: Cengiz Günay @ 2010-02-21 21:28 UTC (permalink / raw)
To: Tejun Heo; +Cc: Robert Hancock, linux-kernel, linux-ide
[-- Attachment #1: Type: text/plain, Size: 499 bytes --]
On Sat, Feb 20, 2010 at 8:01 PM, Tejun Heo <tj@kernel.org> wrote:
> Hmmm... So, DRQ gets cleared? That's strange. When then the 18 extra
> bytes happen? Can you please try this one?
It worked!
$ lsscsi
...
[4:0:0:0] cd/dvd ATAPI iHOS104 WL08 /dev/sr0
...
I was able to read a regular DVD in the drive. According to dmesg the
negotiated speed was down to UDMA/33, so I am not sure about the
performance of the drive.
Full dmesg attached.
Thanks!
Cengiz
[-- Attachment #2: dmesg-sata_nv-swncq-polling-pio --]
[-- Type: application/octet-stream, Size: 77185 bytes --]
Linux version 2.6.32testing (root@salon) (gcc version 4.3.3 (Debian 4.3.3-10) ) #4 SMP PREEMPT Sun Feb 21 11:06:46 EST 2010
KERNEL supported cpus:
Intel GenuineIntel
AMD AuthenticAMD
NSC Geode by NSC
Cyrix CyrixInstead
Centaur CentaurHauls
Transmeta GenuineTMx86
Transmeta TransmetaCPU
UMC UMC UMC UMC
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009c400 (usable)
BIOS-e820: 000000000009c400 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000007fef0000 (usable)
BIOS-e820: 000000007fef0000 - 000000007fef3000 (ACPI NVS)
BIOS-e820: 000000007fef3000 - 000000007ff00000 (ACPI data)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
DMI 2.4 present.
Phoenix BIOS detected: BIOS may corrupt low RAM, working around it.
e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
last_pfn = 0x7fef0 max_arch_pfn = 0x100000
MTRR default type: uncachable
MTRR fixed ranges enabled:
00000-9FFFF write-back
A0000-BFFFF uncachable
C0000-CDFFF write-protect
CE000-FFFFF uncachable
MTRR variable ranges enabled:
0 base 000000000 mask F80000000 write-back
1 base 07FF00000 mask FFFF00000 uncachable
2 disabled
3 disabled
4 disabled
5 disabled
6 disabled
7 disabled
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
initial memory mapped : 0 - 01800000
init_memory_mapping: 0000000000000000-00000000377fe000
0000000000 - 0000400000 page 4k
0000400000 - 0037400000 page 2M
0037400000 - 00377fe000 page 4k
kernel direct mapping tables up to 377fe000 @ 10000-15000
RAMDISK: 36bae000 - 37feff4b
Allocated new RAMDISK: 013e6000 - 02827f4b
Move RAMDISK from 0000000036bae000 - 0000000037feff4a to 013e6000 - 02827f4a
ACPI: RSDP 000f7900 00024 (v02 Nvidia)
ACPI: XSDT 7fef30c0 0004C (v01 Nvidia ASUSACPI 42302E31 AWRD 00000000)
ACPI: FACP 7fefa600 000F4 (v03 Nvidia ASUSACPI 42302E31 AWRD 00000000)
ACPI: DSDT 7fef3240 07354 (v01 NVIDIA ASUSACPI 00001000 MSFT 03000000)
ACPI: FACS 7fef0000 00040
ACPI: HPET 7fefa840 00038 (v01 Nvidia ASUSACPI 42302E31 AWRD 00000098)
ACPI: MCFG 7fefa8c0 0003C (v01 Nvidia ASUSACPI 42302E31 AWRD 00000000)
ACPI: APIC 7fefa740 0008E (v01 Nvidia ASUSACPI 42302E31 AWRD 00000000)
ACPI: SSDT 7fefae20 0032C (v01 Nvidia ASUSACPI 42302E31 AWRD 00000000)
ACPI: Local APIC address 0xfee00000
1158MB HIGHMEM available.
887MB LOWMEM available.
mapped low ram: 0 - 377fe000
low ram: 0 - 377fe000
node 0 low ram: 00000000 - 377fe000
node 0 bootmap 00011000 - 00017f00
(9 early reservations) ==> bootmem [0000000000 - 00377fe000]
#0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
#1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000]
#2 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 - 0000007000]
#3 [0001000000 - 00013de7c4] TEXT DATA BSS ==> [0001000000 - 00013de7c4]
#4 [000009c400 - 0000100000] BIOS reserved ==> [000009c400 - 0000100000]
#5 [00013df000 - 00013e5149] BRK ==> [00013df000 - 00013e5149]
#6 [0000010000 - 0000011000] PGTABLE ==> [0000010000 - 0000011000]
#7 [00013e6000 - 0002827f4b] NEW RAMDISK ==> [00013e6000 - 0002827f4b]
#8 [0000011000 - 0000018000] BOOTMAP ==> [0000011000 - 0000018000]
found SMP MP-table at [c00f5d50] f5d50
Zone PFN ranges:
DMA 0x00000010 -> 0x00001000
Normal 0x00001000 -> 0x000377fe
HighMem 0x000377fe -> 0x0007fef0
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
0: 0x00000010 -> 0x0000009c
0: 0x00000100 -> 0x0007fef0
On node 0 totalpages: 523900
free_area_init_node: node 0, pgdat c1324fc0, node_mem_map c2829200
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 3948 pages, LIFO batch:0
Normal zone: 1744 pages used for memmap
Normal zone: 221486 pages, LIFO batch:31
HighMem zone: 2318 pages used for memmap
HighMem zone: 294372 pages, LIFO batch:31
Using APIC driver default
ACPI: PM-Timer IO Port: 0x4008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 4, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
ACPI: IRQ9 used by override.
ACPI: IRQ14 used by override.
ACPI: IRQ15 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
ACPI: HPET id: 0x10de8201 base: 0xfeff0000
SMP: Allowing 4 CPUs, 2 hotplug CPUs
nr_irqs_gsi: 24
PM: Registered nosave memory: 000000000009c000 - 000000000009d000
PM: Registered nosave memory: 000000000009d000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
Allocating PCI resources starting at 7ff00000 (gap: 7ff00000:60100000)
NR_CPUS:4 nr_cpumask_bits:4 nr_cpu_ids:4 nr_node_ids:1
PERCPU: Embedded 11 pages/cpu @c3c00000 s23512 r0 d21544 u1048576
pcpu-alloc: s23512 r0 d21544 u1048576 alloc=1*4194304
pcpu-alloc: [0] 0 1 2 3
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 519806
Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.32testing root=/dev/mapper/nvidia_ceebaiib1 ro
PID hash table entries: 4096 (order: 2, 16384 bytes)
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
Initializing HighMem for node 0 (000377fe:0007fef0)
Memory: 2052264k/2096064k available (2319k kernel code, 42156k reserved, 912k data, 404k init, 1186760k highmem)
virtual kernel memory layout:
fixmap : 0xfff6b000 - 0xfffff000 ( 592 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xf7ffe000 - 0xff7fe000 ( 120 MB)
lowmem : 0xc0000000 - 0xf77fe000 ( 887 MB)
.init : 0xc1329000 - 0xc138e000 ( 404 kB)
.data : 0xc1243e41 - 0xc1328128 ( 912 kB)
.text : 0xc1000000 - 0xc1243e41 (2319 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:384
Extended CMOS year: 2000
spurious 8259A interrupt: IRQ7.
Console: colour VGA+ 80x25
console [tty0] enabled
hpet clockevent registered
Fast TSC calibration using PIT
Detected 2133.591 MHz processor.
Calibrating delay loop (skipped), value calculated using timer frequency.. 4267.18 BogoMIPS (lpj=2133591)
Security Framework initialized
Mount-cache hash table entries: 512
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
mce: CPU supports 6 MCE banks
CPU0: Thermal monitoring enabled (TM2)
using mwait in idle threads.
Checking 'hlt' instruction... OK.
ACPI: Core revision 20090903
..TIMER: vector=0x30 apic1=0 pin1=0 apic2=-1 pin2=-1
..MP-BIOS bug: 8254 timer not connected to IO-APIC
...trying to set up timer (IRQ0) through the 8259A ...
..... (found apic 0 pin 0) ...
....... works.
CPU0: Intel(R) Core(TM)2 CPU 6400 @ 2.13GHz stepping 06
Booting processor 1 APIC 0x1 ip 0x6000
Initializing CPU#1
Calibrating delay using timer specific routine.. 4266.83 BogoMIPS (lpj=2133415)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU1: Thermal monitoring enabled (TM2)
CPU1: Intel(R) Core(TM)2 CPU 6400 @ 2.13GHz stepping 06
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Brought up 2 CPUs
Total of 2 processors activated (8534.01 BogoMIPS).
CPU0 attaching sched-domain:
domain 0: span 0-1 level MC
groups: 0 1
CPU1 attaching sched-domain:
domain 0: span 0-1 level MC
groups: 1 0
PM: Adding info for No Bus:platform
Time: 15:42:34 Date: 02/21/10
NET: Registered protocol family 16
PM: Adding info for No Bus:vtcon0
EISA bus registered
ACPI: bus type pci registered
PM: Adding info for No Bus:id
PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
PCI: MCFG area at e0000000 reserved in E820
PCI: Using MMCONFIG for extended config space
PCI: Using configuration type 1 for base access
PM: Adding info for No Bus:default
bio: create slab <bio-0> at 0
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
PM: Adding info for acpi:LNXSYSTM:00
PM: Adding info for acpi:LNXCPU:00
PM: Adding info for acpi:LNXCPU:01
PM: Adding info for acpi:LNXCPU:02
PM: Adding info for acpi:LNXCPU:03
PM: Adding info for acpi:LNXSYBUS:00
PM: Adding info for acpi:PNP0C0C:00
PM: Adding info for acpi:PNP0A08:00
PM: Adding info for acpi:PNP0C02:00
PM: Adding info for acpi:device:00
PM: Adding info for acpi:device:01
PM: Adding info for acpi:device:02
PM: Adding info for acpi:device:03
PM: Adding info for acpi:device:04
PM: Adding info for acpi:device:05
PM: Adding info for acpi:device:06
PM: Adding info for acpi:device:07
PM: Adding info for acpi:device:08
PM: Adding info for acpi:device:09
PM: Adding info for acpi:device:0a
PM: Adding info for acpi:device:0b
PM: Adding info for acpi:device:0c
PM: Adding info for acpi:device:0d
PM: Adding info for acpi:device:0e
PM: Adding info for acpi:device:0f
PM: Adding info for acpi:device:10
PM: Adding info for acpi:device:11
PM: Adding info for acpi:device:12
PM: Adding info for acpi:device:13
PM: Adding info for acpi:device:14
PM: Adding info for acpi:device:15
PM: Adding info for acpi:device:16
PM: Adding info for acpi:device:17
PM: Adding info for acpi:device:18
PM: Adding info for acpi:device:19
PM: Adding info for acpi:PNP0C02:01
PM: Adding info for acpi:PNP0000:00
PM: Adding info for acpi:PNP0200:00
PM: Adding info for acpi:PNP0100:00
PM: Adding info for acpi:PNP0103:00
PM: Adding info for acpi:PNP0B00:00
PM: Adding info for acpi:PNP0800:00
PM: Adding info for acpi:PNP0C04:00
PM: Adding info for acpi:device:1a
PM: Adding info for acpi:device:1b
PM: Adding info for acpi:device:1c
PM: Adding info for acpi:device:1d
PM: Adding info for acpi:device:1e
PM: Adding info for acpi:device:1f
PM: Adding info for acpi:NVRAIDBUS:00
PM: Adding info for acpi:ATK0110:00
PM: Adding info for acpi:PNP0C0F:00
PM: Adding info for acpi:PNP0C0F:01
PM: Adding info for acpi:PNP0C0F:02
PM: Adding info for acpi:PNP0C0F:03
PM: Adding info for acpi:PNP0C0F:04
PM: Adding info for acpi:PNP0C0F:05
PM: Adding info for acpi:PNP0C0F:06
PM: Adding info for acpi:PNP0C0F:07
PM: Adding info for acpi:PNP0C0F:08
PM: Adding info for acpi:PNP0C0F:09
PM: Adding info for acpi:PNP0C0F:0a
PM: Adding info for acpi:PNP0C0F:0b
PM: Adding info for acpi:PNP0C0F:0c
PM: Adding info for acpi:PNP0C0F:0d
PM: Adding info for acpi:PNP0C0F:0e
PM: Adding info for acpi:PNP0C0F:0f
PM: Adding info for acpi:PNP0C0F:10
PM: Adding info for acpi:PNP0C0F:11
PM: Adding info for acpi:PNP0C0F:12
PM: Adding info for acpi:PNP0C0F:13
PM: Adding info for acpi:PNP0C0F:14
PM: Adding info for acpi:PNP0C0F:15
PM: Adding info for acpi:PNP0C0F:16
PM: Adding info for acpi:PNP0C0F:17
PM: Adding info for acpi:PNP0C0F:18
PM: Adding info for acpi:PNP0C0F:19
PM: Adding info for acpi:PNP0C0F:1a
PM: Adding info for acpi:PNP0C0F:1b
PM: Adding info for acpi:PNP0C0F:1c
PM: Adding info for acpi:PNP0C0F:1d
PM: Adding info for acpi:PNP0C0F:1e
PM: Adding info for acpi:PNP0C0F:1f
PM: Adding info for acpi:PNP0C0F:20
PM: Adding info for acpi:PNP0C0F:21
PM: Adding info for acpi:PNP0C0F:22
PM: Adding info for acpi:PNP0C0F:23
PM: Adding info for acpi:PNP0C0F:24
PM: Adding info for acpi:PNP0C0F:25
PM: Adding info for acpi:PNP0C0F:26
PM: Adding info for acpi:PNP0C0F:27
PM: Adding info for acpi:PNP0C0F:28
PM: Adding info for acpi:PNP0C02:02
PM: Adding info for acpi:PNP0C01:00
PM: Adding info for acpi:LNXTHERM:00
PM: Adding info for acpi:PNP0C0B:00
PM: Adding info for acpi:LNXTHERM:01
PM: Adding info for acpi:LNXPWRBN:00
ACPI: No dock devices found.
ACPI: PCI Root Bridge [PCI0] (0000:00)
PM: Adding info for No Bus:pci0000:00
PM: Adding info for No Bus:0000:00
pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:02.0: PME# disabled
pci 0000:00:04.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:04.0: PME# disabled
pci 0000:00:05.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:05.0: PME# disabled
pci 0000:00:06.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:06.0: PME# disabled
pci 0000:00:07.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:07.0: PME# disabled
pci 0000:00:0a.1: reg 20 io port: [0x5000-0x503f]
pci 0000:00:0a.1: reg 24 io port: [0x5100-0x513f]
pci 0000:00:0a.1: PME# supported from D3hot D3cold
pci 0000:00:0a.1: PME# disabled
pci 0000:00:0b.0: reg 10 32bit mmio: [0xd5006000-0xd5006fff]
pci 0000:00:0b.0: supports D1 D2
pci 0000:00:0b.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:0b.0: PME# disabled
pci 0000:00:0b.1: reg 10 32bit mmio: [0xd5007000-0xd50070ff]
pci 0000:00:0b.1: supports D1 D2
pci 0000:00:0b.1: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:0b.1: PME# disabled
pci 0000:00:0d.0: reg 20 io port: [0xf000-0xf00f]
pci 0000:00:0e.0: reg 10 io port: [0x9f0-0x9f7]
pci 0000:00:0e.0: reg 14 io port: [0xbf0-0xbf3]
pci 0000:00:0e.0: reg 18 io port: [0x970-0x977]
pci 0000:00:0e.0: reg 1c io port: [0xb70-0xb73]
pci 0000:00:0e.0: reg 20 io port: [0xd400-0xd40f]
pci 0000:00:0e.0: reg 24 32bit mmio: [0xd5004000-0xd5004fff]
pci 0000:00:0f.0: reg 10 io port: [0x9e0-0x9e7]
pci 0000:00:0f.0: reg 14 io port: [0xbe0-0xbe3]
pci 0000:00:0f.0: reg 18 io port: [0x960-0x967]
pci 0000:00:0f.0: reg 1c io port: [0xb60-0xb63]
pci 0000:00:0f.0: reg 20 io port: [0xe800-0xe80f]
pci 0000:00:0f.0: reg 24 32bit mmio: [0xd5005000-0xd5005fff]
pci 0000:00:10.1: reg 10 32bit mmio: [0xd5000000-0xd5003fff]
pci 0000:00:10.1: PME# supported from D3hot D3cold
pci 0000:00:10.1: PME# disabled
pci 0000:01:00.0: reg 10 32bit mmio: [0xd0000000-0xd0ffffff]
pci 0000:01:00.0: reg 14 64bit mmio pref: [0xc0000000-0xcfffffff]
pci 0000:01:00.0: reg 1c 64bit mmio: [0xd1000000-0xd1ffffff]
pci 0000:01:00.0: reg 24 io port: [0xa000-0xa07f]
pci 0000:01:00.0: reg 30 32bit mmio pref: [0xd2000000-0xd201ffff]
pci 0000:00:02.0: bridge io port: [0xa000-0xafff]
pci 0000:00:02.0: bridge 32bit mmio: [0xd0000000-0xd2ffffff]
pci 0000:00:02.0: bridge 64bit mmio pref: [0xc0000000-0xcfffffff]
pci 0000:06:06.0: reg 10 32bit mmio: [0xd4001000-0xd40017ff]
pci 0000:06:06.0: reg 14 io port: [0xb000-0xb07f]
pci 0000:06:06.0: supports D2
pci 0000:06:06.0: PME# supported from D2 D3hot D3cold
pci 0000:06:06.0: PME# disabled
pci 0000:06:07.0: reg 10 io port: [0xb400-0xb4ff]
pci 0000:06:07.0: reg 14 32bit mmio: [0xd4000000-0xd40000ff]
pci 0000:06:07.0: reg 30 32bit mmio pref: [0xd3000000-0xd301ffff]
pci 0000:06:07.0: supports D1 D2
pci 0000:06:07.0: PME# supported from D1 D2 D3hot D3cold
pci 0000:06:07.0: PME# disabled
pci 0000:00:10.0: transparent bridge
pci 0000:00:10.0: bridge io port: [0xb000-0xbfff]
pci 0000:00:10.0: bridge 32bit mmio: [0xd3000000-0xd4ffffff]
pci_bus 0000:00: on NUMA node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
PM: Adding info for pci:0000:00:00.0
PM: Adding info for pci:0000:00:00.1
PM: Adding info for pci:0000:00:00.2
PM: Adding info for pci:0000:00:00.3
PM: Adding info for pci:0000:00:00.4
PM: Adding info for pci:0000:00:01.0
PM: Adding info for pci:0000:00:01.1
PM: Adding info for pci:0000:00:01.2
PM: Adding info for pci:0000:00:01.3
PM: Adding info for pci:0000:00:01.4
PM: Adding info for pci:0000:00:01.5
PM: Adding info for pci:0000:00:01.6
PM: Adding info for pci:0000:00:02.0
PM: Adding info for pci:0000:00:04.0
PM: Adding info for pci:0000:00:05.0
PM: Adding info for pci:0000:00:06.0
PM: Adding info for pci:0000:00:07.0
PM: Adding info for pci:0000:00:09.0
PM: Adding info for pci:0000:00:0a.0
PM: Adding info for pci:0000:00:0a.1
PM: Adding info for pci:0000:00:0a.2
PM: Adding info for pci:0000:00:0b.0
PM: Adding info for pci:0000:00:0b.1
PM: Adding info for pci:0000:00:0d.0
PM: Adding info for pci:0000:00:0e.0
PM: Adding info for pci:0000:00:0f.0
PM: Adding info for pci:0000:00:10.0
PM: Adding info for pci:0000:00:10.1
PM: Adding info for pci:0000:01:00.0
PM: Adding info for No Bus:0000:01
PM: Adding info for No Bus:0000:02
PM: Adding info for No Bus:0000:03
PM: Adding info for No Bus:0000:04
PM: Adding info for No Bus:0000:05
PM: Adding info for pci:0000:06:06.0
PM: Adding info for pci:0000:06:07.0
PM: Adding info for No Bus:0000:06
ACPI: PCI Interrupt Link [LNK1] (IRQs 5 7 9 *10 11 14 15)
ACPI: PCI Interrupt Link [LNK2] (IRQs *5 7 9 10 11 14 15)
ACPI: PCI Interrupt Link [LNK3] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK4] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK5] (IRQs 5 *7 9 10 11 14 15)
ACPI: PCI Interrupt Link [LNK6] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK7] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK8] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LUBA] (IRQs 5 *7 9 10 11 14 15)
ACPI: PCI Interrupt Link [LUBB] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LMAC] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LACI] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LAZA] (IRQs 5 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [LPMU] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LMCI] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSMB] (IRQs 5 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [LUB2] (IRQs *5 7 9 10 11 14 15)
ACPI: PCI Interrupt Link [LIDE] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSID] (IRQs 5 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [LFID] (IRQs 5 7 9 *10 11 14 15)
ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0
ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0
ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0, disabled.
ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled.
ACPI: PCI Interrupt Link [APC5] (IRQs 16) *0
ACPI: PCI Interrupt Link [APC6] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APC7] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APC8] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APMU] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [AAZA] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0
PM: Adding info for No Bus:vga_arbiter
vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
vgaarb: loaded
PCI: Using ACPI for IRQ routing
PM: Adding info for No Bus:lo
hpet0: at MMIO 0xfeff0000, IRQs 2, 8, 31
hpet0: 3 comparators, 32-bit 25.000000 MHz counter
Switching to clocksource tsc
pnp: PnP ACPI init
PM: Adding info for No Bus:pnp0
ACPI: bus type pnp registered
PM: Adding info for pnp:00:00
PM: Adding info for pnp:00:01
PM: Adding info for pnp:00:02
PM: Adding info for pnp:00:03
PM: Adding info for pnp:00:04
PM: Adding info for pnp:00:05
PM: Adding info for pnp:00:06
PM: Adding info for pnp:00:07
PM: Adding info for pnp:00:08
PM: Adding info for pnp:00:09
pnp: PnP ACPI: found 10 devices
ACPI: ACPI bus type pnp unregistered
PnPBIOS: Disabled by ACPI PNP
system 00:01: ioport range 0x4000-0x407f has been reserved
system 00:01: ioport range 0x4080-0x40ff has been reserved
system 00:01: ioport range 0x4400-0x447f has been reserved
system 00:01: ioport range 0x4480-0x44ff has been reserved
system 00:01: ioport range 0x4800-0x487f has been reserved
system 00:01: ioport range 0x4880-0x48ff has been reserved
system 00:02: ioport range 0x4d0-0x4d1 has been reserved
system 00:02: ioport range 0x800-0x87f has been reserved
system 00:02: ioport range 0x290-0x297 has been reserved
system 00:02: ioport range 0x880-0x88f has been reserved
system 00:08: iomem range 0xe0000000-0xefffffff has been reserved
system 00:09: iomem range 0xdbc00-0xdbfff has been reserved
system 00:09: iomem range 0xf0000-0xf7fff could not be reserved
system 00:09: iomem range 0xf8000-0xfbfff could not be reserved
system 00:09: iomem range 0xfc000-0xfffff could not be reserved
system 00:09: iomem range 0xfeff0000-0xfeff00ff has been reserved
system 00:09: iomem range 0x7fef0000-0x7fefffff could not be reserved
system 00:09: iomem range 0xffff0000-0xffffffff has been reserved
system 00:09: iomem range 0x0-0x9ffff could not be reserved
system 00:09: iomem range 0x100000-0x7feeffff could not be reserved
system 00:09: iomem range 0xfec00000-0xfec00fff could not be reserved
system 00:09: iomem range 0xfee00000-0xfee00fff has been reserved
system 00:09: iomem range 0xfeff0000-0xfeff03ff could not be reserved
PM: Adding info for No Bus:mem
PM: Adding info for No Bus:kmem
PM: Adding info for No Bus:null
PM: Adding info for No Bus:port
PM: Adding info for No Bus:zero
PM: Adding info for No Bus:full
PM: Adding info for No Bus:random
PM: Adding info for No Bus:urandom
PM: Adding info for No Bus:kmsg
pci 0000:06:07.0: BAR 6: address space collision on of device [0xd3000000-0xd301ffff]
pci 0000:00:02.0: PCI bridge, secondary bus 0000:01
pci 0000:00:02.0: IO window: 0xa000-0xafff
pci 0000:00:02.0: MEM window: 0xd0000000-0xd2ffffff
pci 0000:00:02.0: PREFETCH window: 0x000000c0000000-0x000000cfffffff
pci 0000:00:04.0: PCI bridge, secondary bus 0000:02
pci 0000:00:04.0: IO window: disabled
pci 0000:00:04.0: MEM window: disabled
pci 0000:00:04.0: PREFETCH window: disabled
pci 0000:00:05.0: PCI bridge, secondary bus 0000:03
pci 0000:00:05.0: IO window: disabled
pci 0000:00:05.0: MEM window: disabled
pci 0000:00:05.0: PREFETCH window: disabled
pci 0000:00:06.0: PCI bridge, secondary bus 0000:04
pci 0000:00:06.0: IO window: disabled
pci 0000:00:06.0: MEM window: disabled
pci 0000:00:06.0: PREFETCH window: disabled
pci 0000:00:07.0: PCI bridge, secondary bus 0000:05
pci 0000:00:07.0: IO window: disabled
pci 0000:00:07.0: MEM window: disabled
pci 0000:00:07.0: PREFETCH window: disabled
pci 0000:00:10.0: PCI bridge, secondary bus 0000:06
pci 0000:00:10.0: IO window: 0xb000-0xbfff
pci 0000:00:10.0: MEM window: 0xd3000000-0xd4ffffff
pci 0000:00:10.0: PREFETCH window: 0x80000000-0x800fffff
pci 0000:00:02.0: setting latency timer to 64
pci 0000:00:04.0: setting latency timer to 64
pci 0000:00:05.0: setting latency timer to 64
pci 0000:00:06.0: setting latency timer to 64
pci 0000:00:07.0: setting latency timer to 64
pci 0000:00:10.0: setting latency timer to 64
pci_bus 0000:00: resource 0 io: [0x00-0xffff]
pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
pci_bus 0000:01: resource 0 io: [0xa000-0xafff]
pci_bus 0000:01: resource 1 mem: [0xd0000000-0xd2ffffff]
pci_bus 0000:01: resource 2 pref mem [0xc0000000-0xcfffffff]
pci_bus 0000:06: resource 0 io: [0xb000-0xbfff]
pci_bus 0000:06: resource 1 mem: [0xd3000000-0xd4ffffff]
pci_bus 0000:06: resource 2 pref mem [0x80000000-0x800fffff]
pci_bus 0000:06: resource 3 io: [0x00-0xffff]
pci_bus 0000:06: resource 4 mem: [0x000000-0xffffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
pci 0000:01:00.0: Boot video device
Trying to unpack rootfs image as initramfs...
Freeing initrd memory: 20743k freed
PM: Adding info for No Bus:mcelog
PM: Adding info for No Bus:msr0
PM: Adding info for No Bus:msr1
PM: Adding info for platform:pcspkr
PM: Adding info for No Bus:snapshot
highmem bounce pool size: 64 pages
ROMFS MTD (C) 2007 Red Hat, Inc.
msgmni has been set to 1733
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
pcieport 0000:00:02.0: setting latency timer to 64
PM: Adding info for pci_express:0000:00:02.0:pcie08
pcieport 0000:00:04.0: setting latency timer to 64
PM: Adding info for pci_express:0000:00:04.0:pcie08
pcieport 0000:00:05.0: setting latency timer to 64
PM: Adding info for pci_express:0000:00:05.0:pcie08
pcieport 0000:00:06.0: setting latency timer to 64
PM: Adding info for pci_express:0000:00:06.0:pcie08
pcieport 0000:00:07.0: setting latency timer to 64
PM: Adding info for pci_express:0000:00:07.0:pcie08
PM: Adding info for No Bus:pnp1
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
PM: Adding info for No Bus:tty
PM: Adding info for No Bus:console
PM: Adding info for No Bus:tty0
PM: Adding info for No Bus:vcs
PM: Adding info for No Bus:vcsa
PM: Adding info for No Bus:vcs1
PM: Adding info for No Bus:vcsa1
PM: Adding info for No Bus:tty1
PM: Adding info for No Bus:tty2
PM: Adding info for No Bus:tty3
PM: Adding info for No Bus:tty4
PM: Adding info for No Bus:tty5
PM: Adding info for No Bus:tty6
PM: Adding info for No Bus:tty7
PM: Adding info for No Bus:tty8
PM: Adding info for No Bus:tty9
PM: Adding info for No Bus:tty10
PM: Adding info for No Bus:tty11
PM: Adding info for No Bus:tty12
PM: Adding info for No Bus:tty13
PM: Adding info for No Bus:tty14
PM: Adding info for No Bus:tty15
PM: Adding info for No Bus:tty16
PM: Adding info for No Bus:tty17
PM: Adding info for No Bus:tty18
PM: Adding info for No Bus:tty19
PM: Adding info for No Bus:tty20
PM: Adding info for No Bus:tty21
PM: Adding info for No Bus:tty22
PM: Adding info for No Bus:tty23
PM: Adding info for No Bus:tty24
PM: Adding info for No Bus:tty25
PM: Adding info for No Bus:tty26
PM: Adding info for No Bus:tty27
PM: Adding info for No Bus:tty28
PM: Adding info for No Bus:tty29
PM: Adding info for No Bus:tty30
PM: Adding info for No Bus:tty31
PM: Adding info for No Bus:tty32
PM: Adding info for No Bus:tty33
PM: Adding info for No Bus:tty34
PM: Adding info for No Bus:tty35
PM: Adding info for No Bus:tty36
PM: Adding info for No Bus:tty37
PM: Adding info for No Bus:tty38
PM: Adding info for No Bus:tty39
PM: Adding info for No Bus:tty40
PM: Adding info for No Bus:tty41
PM: Adding info for No Bus:tty42
PM: Adding info for No Bus:tty43
PM: Adding info for No Bus:tty44
PM: Adding info for No Bus:tty45
PM: Adding info for No Bus:tty46
PM: Adding info for No Bus:tty47
PM: Adding info for No Bus:tty48
PM: Adding info for No Bus:tty49
PM: Adding info for No Bus:tty50
PM: Adding info for No Bus:tty51
PM: Adding info for No Bus:tty52
PM: Adding info for No Bus:tty53
PM: Adding info for No Bus:tty54
PM: Adding info for No Bus:tty55
PM: Adding info for No Bus:tty56
PM: Adding info for No Bus:tty57
PM: Adding info for No Bus:tty58
PM: Adding info for No Bus:tty59
PM: Adding info for No Bus:tty60
PM: Adding info for No Bus:tty61
PM: Adding info for No Bus:tty62
PM: Adding info for No Bus:tty63
PM: Adding info for No Bus:ptmx
PM: Adding info for No Bus:hpet
PM: Adding info for No Bus:isa
PM: Adding info for No Bus:ram0
PM: Adding info for No Bus:1:0
PM: Adding info for No Bus:ram1
PM: Adding info for No Bus:1:1
PM: Adding info for No Bus:ram2
PM: Adding info for No Bus:1:2
PM: Adding info for No Bus:ram3
PM: Adding info for No Bus:1:3
PM: Adding info for No Bus:ram4
PM: Adding info for No Bus:1:4
PM: Adding info for No Bus:ram5
PM: Adding info for No Bus:1:5
PM: Adding info for No Bus:ram6
PM: Adding info for No Bus:1:6
PM: Adding info for No Bus:ram7
PM: Adding info for No Bus:1:7
PM: Adding info for No Bus:ram8
PM: Adding info for No Bus:1:8
PM: Adding info for No Bus:ram9
PM: Adding info for No Bus:1:9
PM: Adding info for No Bus:ram10
PM: Adding info for No Bus:1:10
PM: Adding info for No Bus:ram11
PM: Adding info for No Bus:1:11
PM: Adding info for No Bus:ram12
PM: Adding info for No Bus:1:12
PM: Adding info for No Bus:ram13
PM: Adding info for No Bus:1:13
PM: Adding info for No Bus:ram14
PM: Adding info for No Bus:1:14
PM: Adding info for No Bus:ram15
PM: Adding info for No Bus:1:15
brd: module loaded
PNP: No PS/2 controller found. Probing ports directly.
PM: Adding info for platform:i8042
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
PM: Adding info for serio:serio0
PM: Adding info for serio:serio1
PM: Adding info for No Bus:mice
PM: Adding info for No Bus:psaux
mice: PS/2 mouse device common for all mice
PM: Adding info for platform:eisa.0
EISA: Probing bus 0 at eisa.0
PM: Removing info for platform:eisa.0
cpuidle: using governor ladder
TCP cubic registered
Using IPI No-Shortcut mode
PM: Adding info for No Bus:cpu_dma_latency
PM: Adding info for No Bus:network_latency
PM: Adding info for No Bus:network_throughput
PM: Checking image partition /dev/hda6
PM: Resume from disk failed.
Magic number: 14:826:740
Freeing unused kernel memory: 404k freed
NET: Registered protocol family 1
PM: Adding info for No Bus:cooling_device0
fan PNP0C0B:00: registered as cooling_device0
ACPI: Fan [FAN] (on)
PM: Adding info for No Bus:thermal_zone0
thermal LNXTHERM:01: registered as thermal_zone0
ACPI: Thermal Zone [THRM] (40 C)
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Uniform Multi-Platform E-IDE driver
SCSI subsystem initialized
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci_hcd: block sizes: ed 64 td 64
ACPI: PCI Interrupt Link [APCF] enabled at IRQ 23
ohci_hcd 0000:00:0b.0: PCI INT A -> Link[APCF] -> GSI 23 (level, low) -> IRQ 23
ohci_hcd 0000:00:0b.0: setting latency timer to 64
ohci_hcd 0000:00:0b.0: OHCI Host Controller
drivers/usb/core/inode.c: creating file 'devices'
drivers/usb/core/inode.c: creating file '001'
ohci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:0b.0: created debug files
ohci_hcd 0000:00:0b.0: supports USB remote wakeup
ohci_hcd 0000:00:0b.0: irq 23, io mem 0xd5006000
r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Warning! ehci_hcd should always be loaded before uhci_hcd and ohci_hcd, not after
ehci_hcd: block sizes: qh 60 qtd 96 itd 160 sitd 96
ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17
r8169 0000:06:07.0: PCI INT A -> Link[APC2] -> GSI 17 (level, low) -> IRQ 17
r8169 0000:06:07.0: no PCI Express capability
PM: Adding info for No Bus:eth0
eth0: RTL8169sb/8110sb at 0xf8b2e000, 00:14:d1:1a:ac:15, XID 10000000 IRQ 17
udev: renamed network interface eth0 to eth1
ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16
ohci1394 0000:06:06.0: PCI INT A -> Link[APC1] -> GSI 16 (level, low) -> IRQ 16
PM: Adding info for ieee1394:fw-host0
PM: Adding info for No Bus:fw-host0
libata version 3.00 loaded.
ohci_hcd 0000:00:0b.0: OHCI controller state
ohci_hcd 0000:00:0b.0: OHCI 1.0, NO legacy support registers
ohci_hcd 0000:00:0b.0: control 0x683 RWE RWC HCFS=operational CBSR=3
ohci_hcd 0000:00:0b.0: cmdstatus 0x00000 SOC=0
ohci_hcd 0000:00:0b.0: intrstatus 0x00000044 RHSC SF
ohci_hcd 0000:00:0b.0: intrenable 0x8000000a MIE RD WDH
ohci_hcd 0000:00:0b.0: hcca frame #0003
ohci_hcd 0000:00:0b.0: roothub.a 01000208 POTPGT=1 NPS NDP=8(8)
ohci_hcd 0000:00:0b.0: roothub.b 00000000 PPCM=0000 DR=0000
ohci_hcd 0000:00:0b.0: roothub.status 00008000 DRWE
ohci_hcd 0000:00:0b.0: roothub.portstatus [0] 0x00010301 CSC LSDA PPS CCS
ohci_hcd 0000:00:0b.0: roothub.portstatus [1] 0x00010101 CSC PPS CCS
ohci_hcd 0000:00:0b.0: roothub.portstatus [2] 0x00010101 CSC PPS CCS
ohci_hcd 0000:00:0b.0: roothub.portstatus [3] 0x00000100 PPS
ohci_hcd 0000:00:0b.0: roothub.portstatus [4] 0x00000100 PPS
ohci_hcd 0000:00:0b.0: roothub.portstatus [5] 0x00010101 CSC PPS CCS
ohci_hcd 0000:00:0b.0: roothub.portstatus [6] 0x00000100 PPS
ohci_hcd 0000:00:0b.0: roothub.portstatus [7] 0x00000100 PPS
usb usb1: default language 0x0409
usb usb1: udev 1, busnum 1, minor = 0
usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: OHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.32testing ohci_hcd
usb usb1: SerialNumber: 0000:00:0b.0
PM: Adding info for usb:usb1
usb usb1: uevent
usb usb1: usb_probe_device
usb usb1: configuration #1 chosen from 1 choice
usb usb1: adding 1-0:1.0 (config #1, interface 0)
PM: Adding info for usb:1-0:1.0
usb 1-0:1.0: uevent
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: no power switching (usb 1.0)
hub 1-0:1.0: global over-current protection
hub 1-0:1.0: power on to power good time: 2ms
hub 1-0:1.0: local power source is good
hub 1-0:1.0: no over-current condition exists
hub 1-0:1.0: trying to enable port power on non-switchable hub
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev1.1
drivers/usb/core/inode.c: creating file '001'
PM: Adding info for No Bus:ep_00
ACPI: PCI Interrupt Link [APCL] enabled at IRQ 22
ehci_hcd 0000:00:0b.1: PCI INT B -> Link[APCL] -> GSI 22 (level, low) -> IRQ 22
ehci_hcd 0000:00:0b.1: setting latency timer to 64
ehci_hcd 0000:00:0b.1: EHCI Host Controller
drivers/usb/core/inode.c: creating file '002'
ehci_hcd 0000:00:0b.1: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:0b.1: reset hcs_params 0x101888 dbg=1 cc=1 pcc=8 !ppc ports=8
ehci_hcd 0000:00:0b.1: reset portroute 0 0 0 0 0 0 0 0
ehci_hcd 0000:00:0b.1: reset hcc_params a086 caching frame 256/512/1024 park
ehci_hcd 0000:00:0b.1: park 0
ehci_hcd 0000:00:0b.1: debug port 1
ehci_hcd 0000:00:0b.1: reset command 080b02 park=3 ithresh=8 period=1024 Reset HALT
ehci_hcd 0000:00:0b.1: cache line size of 32 is not supported
ehci_hcd 0000:00:0b.1: supports USB remote wakeup
ehci_hcd 0000:00:0b.1: irq 22, io mem 0xd5007000
ehci_hcd 0000:00:0b.1: reset command 080b02 park=3 ithresh=8 period=1024 Reset HALT
ehci_hcd 0000:00:0b.1: init command 010009 (park)=0 ithresh=1 period=256 RUN
usb usb1: uevent
usb usb1: uevent
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[16] MMIO=[d4001000-d40017ff] Max Packet=[2] IR/IT contexts=[4/8]
ehci_hcd 0000:00:0b.1: USB 2.0 started, EHCI 1.00
usb usb2: default language 0x0409
usb usb2: udev 1, busnum 2, minor = 128
usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: EHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.32testing ehci_hcd
usb usb2: SerialNumber: 0000:00:0b.1
PM: Adding info for usb:usb2
usb usb2: uevent
usb usb2: usb_probe_device
usb usb2: configuration #1 chosen from 1 choice
usb usb2: adding 2-0:1.0 (config #1, interface 0)
PM: Adding info for usb:2-0:1.0
usb 2-0:1.0: uevent
hub 2-0:1.0: usb_probe_interface
hub 2-0:1.0: usb_probe_interface - got id
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 8 ports detected
hub 2-0:1.0: standalone hub
hub 2-0:1.0: no power switching (usb 1.0)
hub 2-0:1.0: individual port over-current protection
hub 2-0:1.0: power on to power good time: 20ms
hub 2-0:1.0: local power source is good
hub 2-0:1.0: trying to enable port power on non-switchable hub
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev2.1
drivers/usb/core/inode.c: creating file '001'
PM: Adding info for No Bus:ep_00
amd74xx 0000:00:0d.0: UDMA133 controller
amd74xx 0000:00:0d.0: IDE controller (0x10de:0x0265 rev 0xa1)
amd74xx 0000:00:0d.0: IDE port disabled
amd74xx 0000:00:0d.0: BIOS didn't set cable bits correctly. Enabling workaround.
amd74xx 0000:00:0d.0: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xf008-0xf00f
Probing IDE interface ide0...
ohci1394: fw-host0: Serial EEPROM has suspicious values, attempting to set max_packet_size to 512 bytes
usb usb2: uevent
usb usb2: uevent
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00010300 CSC LSDA PPS
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [1] = 0x00010100 CSC PPS
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [2] = 0x00010100 CSC PPS
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [5] = 0x00010100 CSC PPS
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 2-0:1.0: port 1: status 0501 change 0001
ehci_hcd 0000:00:0b.1: GetStatus port 2 status 001803 POWER sig=j CSC CONNECT
hub 2-0:1.0: port 2: status 0501 change 0001
ehci_hcd 0000:00:0b.1: GetStatus port 3 status 001803 POWER sig=j CSC CONNECT
hub 2-0:1.0: port 3: status 0501 change 0001
ehci_hcd 0000:00:0b.1: GetStatus port 6 status 001803 POWER sig=j CSC CONNECT
hub 2-0:1.0: port 6: status 0501 change 0001
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0000
hub 2-0:1.0: state 7 ports 8 chg 004e evt 0000
hub 2-0:1.0: port 1, status 0501, change 0000, 480 Mb/s
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 2-0:1.0: port 2, status 0501, change 0000, 480 Mb/s
ehci_hcd 0000:00:0b.1: port 2 high speed
ehci_hcd 0000:00:0b.1: GetStatus port 2 status 001005 POWER sig=se0 PE CONNECT
usb 2-2: new high speed USB device using ehci_hcd and address 3
ehci_hcd 0000:00:0b.1: port 2 high speed
ehci_hcd 0000:00:0b.1: GetStatus port 2 status 001005 POWER sig=se0 PE CONNECT
usb 2-2: default language 0x0409
ehci_hcd 0000:00:0b.1: detected XactErr len 0/8 retry 1
usb 2-2: udev 3, busnum 2, minor = 130
usb 2-2: New USB device found, idVendor=058f, idProduct=6362
usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-2: Product: Mass Storage Device
usb 2-2: Manufacturer: Generic
usb 2-2: SerialNumber: 058F312D81B
PM: Adding info for usb:2-2
usb 2-2: uevent
usb 2-2: usb_probe_device
usb 2-2: configuration #1 chosen from 1 choice
usb 2-2: adding 2-2:1.0 (config #1, interface 0)
PM: Adding info for usb:2-2:1.0
usb 2-2:1.0: uevent
PM: Adding info for No Bus:ep_01
PM: Adding info for No Bus:ep_82
PM: Adding info for No Bus:usbdev2.3
drivers/usb/core/inode.c: creating file '003'
PM: Adding info for No Bus:ep_00
hub 2-0:1.0: port 3, status 0501, change 0000, 480 Mb/s
usb 2-2: uevent
usb 2-2: uevent
Initializing USB Mass Storage driver...
usb-storage 2-2:1.0: usb_probe_interface
usb-storage 2-2:1.0: usb_probe_interface - got id
scsi0 : SCSI emulation for USB Mass Storage devices
PM: Adding info for scsi:host0
PM: Adding info for No Bus:host0
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
ehci_hcd 0000:00:0b.1: port 3 high speed
ehci_hcd 0000:00:0b.1: GetStatus port 3 status 001005 POWER sig=se0 PE CONNECT
usb 2-3: new high speed USB device using ehci_hcd and address 4
ehci_hcd 0000:00:0b.1: port 3 high speed
ehci_hcd 0000:00:0b.1: GetStatus port 3 status 001005 POWER sig=se0 PE CONNECT
hda: PIONEER DVD-RW DVR-111D, ATAPI CD/DVD-ROM drive
usb 2-3: default language 0x0409
usb 2-3: udev 4, busnum 2, minor = 131
usb 2-3: New USB device found, idVendor=05e3, idProduct=0605
usb 2-3: New USB device strings: Mfr=0, Product=1, SerialNumber=0
usb 2-3: Product: USB2.0 Hub
PM: Adding info for usb:2-3
usb 2-3: uevent
usb 2-3: usb_probe_device
usb 2-3: configuration #1 chosen from 1 choice
usb 2-3: adding 2-3:1.0 (config #1, interface 0)
PM: Adding info for usb:2-3:1.0
usb 2-3:1.0: uevent
hub 2-3:1.0: usb_probe_interface
hub 2-3:1.0: usb_probe_interface - got id
hub 2-3:1.0: USB hub found
hub 2-3:1.0: 4 ports detected
usb 2-3: uevent
hub 2-3:1.0: standalone hub
hub 2-3:1.0: individual port power switching
hub 2-3:1.0: individual port over-current protection
hub 2-3:1.0: Single TT
hub 2-3:1.0: TT requires at most 32 FS bit times (2664 ns)
hub 2-3:1.0: Port indicators are supported
hub 2-3:1.0: power on to power good time: 100ms
hub 2-3:1.0: local power source is good
hub 2-3:1.0: enabling power on all ports
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev2.4
drivers/usb/core/inode.c: creating file '004'
PM: Adding info for No Bus:ep_00
hub 2-0:1.0: port 6, status 0501, change 0000, 480 Mb/s
usb 2-3: uevent
ehci_hcd 0000:00:0b.1: port 6 high speed
ehci_hcd 0000:00:0b.1: GetStatus port 6 status 001005 POWER sig=se0 PE CONNECT
hub 2-3:1.0: port 1: status 0101 change 0001
usb 2-6: new high speed USB device using ehci_hcd and address 5
ehci_hcd 0000:00:0b.1: port 6 high speed
ehci_hcd 0000:00:0b.1: GetStatus port 6 status 001005 POWER sig=se0 PE CONNECT
usb 2-3: link qh256-0001/c1d96b40 start 1 [1/0 us]
usb 2-6: udev 5, busnum 2, minor = 132
usb 2-6: New USB device found, idVendor=0409, idProduct=0059
usb 2-6: New USB device strings: Mfr=0, Product=0, SerialNumber=0
PM: Adding info for usb:2-6
usb 2-6: uevent
usb 2-6: usb_probe_device
usb 2-6: configuration #1 chosen from 1 choice
usb 2-6: adding 2-6:1.0 (config #1, interface 0)
PM: Adding info for usb:2-6:1.0
usb 2-6:1.0: uevent
hub 2-6:1.0: usb_probe_interface
hub 2-6:1.0: usb_probe_interface - got id
hub 2-6:1.0: USB hub found
hub 2-6:1.0: 4 ports detected
hub 2-6:1.0: standalone hub
hub 2-6:1.0: individual port power switching
hub 2-6:1.0: individual port over-current protection
hub 2-6:1.0: Single TT
hub 2-6:1.0: TT requires at most 16 FS bit times (1332 ns)
hub 2-6:1.0: Port indicators are supported
hub 2-6:1.0: power on to power good time: 100ms
usb 2-6: uevent
hub 2-6:1.0: local power source is good
hub 2-6:1.0: enabling power on all ports
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev2.5
usb 2-6: uevent
drivers/usb/core/inode.c: creating file '005'
PM: Adding info for No Bus:ep_00
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00010301 CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0001, 1.5 Mb/s
hub 2-6:1.0: port 1: status 0301 change 0001
hub 2-6:1.0: port 3: status 0101 change 0001
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-3:1.0: state 7 ports 4 chg 0002 evt 0000
hub 2-3:1.0: port 1, status 0101, change 0000, 12 Mb/s
usb 2-6: link qh256-0001/c1d96cc0 start 2 [1/0 us]
usb 2-3.1: new high speed USB device using ehci_hcd and address 6
usb 2-3.1: udev 6, busnum 2, minor = 133
usb 2-3.1: New USB device found, idVendor=0409, idProduct=0059
usb 2-3.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
PM: Adding info for usb:2-3.1
usb 2-3.1: uevent
usb 2-3.1: usb_probe_device
usb 2-3.1: configuration #1 chosen from 1 choice
usb 2-3.1: adding 2-3.1:1.0 (config #1, interface 0)
PM: Adding info for usb:2-3.1:1.0
usb 2-3.1:1.0: uevent
hub 2-3.1:1.0: usb_probe_interface
hub 2-3.1:1.0: usb_probe_interface - got id
hub 2-3.1:1.0: USB hub found
hub 2-3.1:1.0: 4 ports detected
hub 2-3.1:1.0: standalone hub
hub 2-3.1:1.0: individual port power switching
hub 2-3.1:1.0: individual port over-current protection
hub 2-3.1:1.0: Single TT
hub 2-3.1:1.0: TT requires at most 16 FS bit times (1332 ns)
hub 2-3.1:1.0: Port indicators are supported
hub 2-3.1:1.0: power on to power good time: 100ms
hub 2-3.1:1.0: local power source is good
hub 2-3.1:1.0: enabling power on all ports
usb 2-3.1: uevent
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev2.6
drivers/usb/core/inode.c: creating file '006'
PM: Adding info for No Bus:ep_00
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030300 PESC CSC LSDA PPS
hub 1-0:1.0: port 1, status 0300, change 0003, 1.5 Mb/s
usb 2-3.1: uevent
PM: Adding info for ieee1394:001106000000bd66
PM: Adding info for No Bus:001106000000bd66
ieee1394: Host added: ID:BUS[0-00:1023] GUID[001106000000bd66]
PM: Adding info for ieee1394:001a66fffee31809
PM: Adding info for No Bus:001a66fffee31809
ieee1394: Node added: ID:BUS[0-01:1023] GUID[001a66fffee31809]
PM: Adding info for ieee1394:001a66fffee31809-0
PM: Adding info for No Bus:001a66fffee31809-0
PM: Adding info for ieee1394:001a66fffee31809-1
PM: Adding info for No Bus:001a66fffee31809-1
PM: Adding info for No Bus:ide0
PM: Adding info for No Bus:ide0
hda: host max PIO5 wanted PIO255(auto-tune) selected PIO4
hda: UDMA/66 mode selected
ide0 at 0x170-0x177,0x376 on irq 15
PM: Adding info for ide:0.0
sata_nv 0000:00:0e.0: version 3.5
ACPI: PCI Interrupt Link [APSI] enabled at IRQ 21
sata_nv 0000:00:0e.0: PCI INT A -> Link[APSI] -> GSI 21 (level, low) -> IRQ 21
sata_nv 0000:00:0e.0: Using SWNCQ mode
sata_nv 0000:00:0e.0: setting latency timer to 64
scsi1 : sata_nv
PM: Adding info for scsi:host1
PM: Adding info for No Bus:host1
scsi2 : sata_nv
PM: Adding info for scsi:host2
PM: Adding info for No Bus:host2
ata1: SATA max UDMA/133 cmd 0x9f0 ctl 0xbf0 bmdma 0xd400 irq 21
ata2: SATA max UDMA/133 cmd 0x970 ctl 0xb70 bmdma 0xd408 irq 21
ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 20
sata_nv 0000:00:0f.0: PCI INT A -> Link[APSJ] -> GSI 20 (level, low) -> IRQ 20
sata_nv 0000:00:0f.0: Using SWNCQ mode
sata_nv 0000:00:0f.0: setting latency timer to 64
scsi3 : sata_nv
PM: Adding info for scsi:host3
PM: Adding info for No Bus:host3
scsi4 : sata_nv
PM: Adding info for scsi:host4
PM: Adding info for No Bus:host4
ata3: SATA max UDMA/133 cmd 0x9e0 ctl 0xbe0 bmdma 0xe800 irq 20
ata4: SATA max UDMA/133 cmd 0x960 ctl 0xb60 bmdma 0xe808 irq 20
hub 2-3.1:1.0: port 1: status 0301 change 0001
hub 2-3.1:1.0: port 2: status 0101 change 0001
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x300
hub 2-6:1.0: state 7 ports 4 chg 000a evt 0000
hub 2-6:1.0: port 1, status 0301, change 0000, 1.5 Mb/s
hub 2-6:1.0: port 1 not reset yet, waiting 10ms
usb 2-6.1: new low speed USB device using ehci_hcd and address 7
hub 2-6:1.0: port 1 not reset yet, waiting 10ms
usb 2-3.1: link qh256-0001/c1dcd640 start 3 [1/0 us]
usb 2-6.1: skipped 1 descriptor after interface
usb 2-6.1: default language 0x0409
usb 2-6.1: udev 7, busnum 2, minor = 134
usb 2-6.1: New USB device found, idVendor=2222, idProduct=3100
usb 2-6.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 2-6.1: Product: Macally ECOMouse
usb 2-6.1: Manufacturer: Macally Peripherals
PM: Adding info for usb:2-6.1
usb 2-6.1: uevent
usb 2-6.1: usb_probe_device
usb 2-6.1: configuration #1 chosen from 1 choice
usb 2-6.1: adding 2-6.1:1.0 (config #1, interface 0)
PM: Adding info for usb:2-6.1:1.0
usb 2-6.1:1.0: uevent
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev2.7
drivers/usb/core/inode.c: creating file '007'
PM: Adding info for No Bus:ep_00
usb 2-6.1: uevent
hub 2-6:1.0: port 3, status 0101, change 0000, 12 Mb/s
usb 2-6.1: uevent
usbcore: registered new interface driver hiddev
usbhid 2-6.1:1.0: usb_probe_interface
usbhid 2-6.1:1.0: usb_probe_interface - got id
PM: Adding info for hid:0003:2222:3100.0001
PM: Adding info for No Bus:input0
input: Macally Peripherals Macally ECOMouse as /devices/pci0000:00/0000:00:0b.1/usb2/2-6/2-6.1/2-6.1:1.0/input/input0
PM: Adding info for No Bus:mouse0
generic-usb 0003:2222:3100.0001: input: USB HID v1.00 Mouse [Macally Peripherals Macally ECOMouse ] on usb-0000:00:0b.1-6.1/input0
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
hub 2-6:1.0: port 3 not reset yet, waiting 10ms
usb 2-6.3: new full speed USB device using ehci_hcd and address 8
hub 2-6:1.0: port 3 not reset yet, waiting 10ms
ata3: SATA link down (SStatus 0 SControl 300)
usb 2-6.3: ep0 maxpacket = 8
usb 2-6.3: default language 0x0409
usb 2-6.3: udev 8, busnum 2, minor = 135
usb 2-6.3: New USB device found, idVendor=05e3, idProduct=0604
usb 2-6.3: New USB device strings: Mfr=0, Product=1, SerialNumber=0
usb 2-6.3: Product: USB Hub
PM: Adding info for usb:2-6.3
usb 2-6.3: uevent
usb 2-6.3: usb_probe_device
usb 2-6.3: configuration #1 chosen from 1 choice
usb 2-6.3: adding 2-6.3:1.0 (config #1, interface 0)
PM: Adding info for usb:2-6.3:1.0
usb 2-6.3:1.0: uevent
hub 2-6.3:1.0: usb_probe_interface
hub 2-6.3:1.0: usb_probe_interface - got id
hub 2-6.3:1.0: USB hub found
usb 2-6.3: uevent
hub 2-6.3:1.0: 4 ports detected
hub 2-6.3:1.0: standalone hub
hub 2-6.3:1.0: individual port power switching
hub 2-6.3:1.0: individual port over-current protection
hub 2-6.3:1.0: power on to power good time: 100ms
hub 2-6.3:1.0: local power source is good
hub 2-6.3:1.0: enabling power on all ports
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev2.8
drivers/usb/core/inode.c: creating file '008'
PM: Adding info for No Bus:ep_00
hub 2-3.1:1.0: state 7 ports 4 chg 0006 evt 0000
usb 2-6.3: uevent
hub 2-3.1:1.0: port 1, status 0301, change 0000, 1.5 Mb/s
hub 2-3.1:1.0: port 1 not reset yet, waiting 10ms
usb 2-3.1.1: new low speed USB device using ehci_hcd and address 9
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: ATA-7: SAMSUNG SP2504C, VT100-41, max UDMA7
ata1.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32)
hub 2-3.1:1.0: port 1 not reset yet, waiting 10ms
hub 2-6.3:1.0: port 3: status 0301 change 0001
ata1.00: configured for UDMA/133
scsi 1:0:0:0: Direct-Access ATA SAMSUNG SP2504C VT10 PQ: 0 ANSI: 5
PM: Adding info for scsi:target1:0:0
PM: Adding info for scsi:1:0:0:0
PM: Adding info for No Bus:1:0:0:0
PM: Adding info for No Bus:1:0:0:0
usb 2-3.1.1: skipped 1 descriptor after interface
usb 2-3.1.1: skipped 1 descriptor after interface
usb 2-3.1.1: default language 0x0409
usb 2-3.1.1: udev 9, busnum 2, minor = 136
usb 2-3.1.1: New USB device found, idVendor=10d5, idProduct=0004
usb 2-3.1.1: New USB device strings: Mfr=0, Product=2, SerialNumber=0
usb 2-3.1.1: Product: PS2 to USB AdapterA3
PM: Adding info for usb:2-3.1.1
usb 2-3.1.1: uevent
usb 2-3.1.1: usb_probe_device
usb 2-3.1.1: configuration #1 chosen from 1 choice
usb 2-3.1.1: uevent
usb 2-3.1.1: adding 2-3.1.1:1.0 (config #1, interface 0)
PM: Adding info for usb:2-3.1.1:1.0
usb 2-3.1.1:1.0: uevent
usbhid 2-3.1.1:1.0: usb_probe_interface
usbhid 2-3.1.1:1.0: usb_probe_interface - got id
PM: Adding info for hid:0003:10D5:0004.0002
PM: Adding info for No Bus:input1
input: PS2 to USB AdapterA3 as /devices/pci0000:00/0000:00:0b.1/usb2/2-3/2-3.1/2-3.1.1/2-3.1.1:1.0/input/input1
usb 2-3.1.1: link qh8-0e01/c1dcde40 start 4 [1/2 us]
generic-usb 0003:10D5:0004.0002: input: USB HID v1.10 Keyboard [PS2 to USB AdapterA3] on usb-0000:00:0b.1-3.1.1/input0
PM: Adding info for No Bus:ep_81
usb 2-3.1.1: adding 2-3.1.1:1.1 (config #1, interface 1)
PM: Adding info for usb:2-3.1.1:1.1
usb 2-3.1.1:1.1: uevent
usbhid 2-3.1.1:1.1: usb_probe_interface
usbhid 2-3.1.1:1.1: usb_probe_interface - got id
PM: Adding info for hid:0003:10D5:0004.0003
PM: Adding info for No Bus:input2
input: PS2 to USB AdapterA3 as /devices/pci0000:00/0000:00:0b.1/usb2/2-3/2-3.1/2-3.1.1/2-3.1.1:1.1/input/input2
usb 2-3.1.1: link qh8-0e01/c1dcdf40 start 5 [1/2 us]
PM: Adding info for No Bus:mouse1
generic-usb 0003:10D5:0004.0003: input: USB HID v1.10 Mouse [PS2 to USB AdapterA3] on usb-0000:00:0b.1-3.1.1/input1
PM: Adding info for No Bus:ep_82
PM: Adding info for No Bus:usbdev2.9
drivers/usb/core/inode.c: creating file '009'
PM: Adding info for No Bus:ep_00
usb 2-3.1.1: uevent
hub 2-3.1:1.0: port 2, status 0101, change 0000, 12 Mb/s
hub 2-3.1:1.0: port 2 not reset yet, waiting 10ms
usb 2-6.3: link qh128-0e01/c1dcdfc0 start 6 [1/2 us]
usb 2-3.1.2: new high speed USB device using ehci_hcd and address 10
hub 2-3.1:1.0: port 2 not reset yet, waiting 10ms
usb 2-3.1.2: default language 0x0409
usb 2-3.1.2: udev 10, busnum 2, minor = 137
usb 2-3.1.2: New USB device found, idVendor=05e3, idProduct=0605
usb 2-3.1.2: New USB device strings: Mfr=0, Product=1, SerialNumber=0
usb 2-3.1.2: Product: USB2.0 Hub
PM: Adding info for usb:2-3.1.2
usb 2-3.1.2: uevent
usb 2-3.1.2: usb_probe_device
usb 2-3.1.2: configuration #1 chosen from 1 choice
usb 2-3.1.2: adding 2-3.1.2:1.0 (config #1, interface 0)
PM: Adding info for usb:2-3.1.2:1.0
usb 2-3.1.2:1.0: uevent
hub 2-3.1.2:1.0: usb_probe_interface
hub 2-3.1.2:1.0: usb_probe_interface - got id
hub 2-3.1.2:1.0: USB hub found
hub 2-3.1.2:1.0: 4 ports detected
hub 2-3.1.2:1.0: standalone hub
hub 2-3.1.2:1.0: individual port power switching
hub 2-3.1.2:1.0: individual port over-current protection
hub 2-3.1.2:1.0: Single TT
hub 2-3.1.2:1.0: TT requires at most 32 FS bit times (2664 ns)
hub 2-3.1.2:1.0: Port indicators are supported
hub 2-3.1.2:1.0: power on to power good time: 100ms
usb 2-3.1.2: uevent
hub 2-3.1.2:1.0: local power source is good
hub 2-3.1.2:1.0: enabling power on all ports
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev2.10
drivers/usb/core/inode.c: creating file '010'
PM: Adding info for No Bus:ep_00
hub 2-6:1.0: state 7 ports 4 chg 0000 evt 0008
usb 2-3.1.2: uevent
hub 2-3.1:1.0: state 7 ports 4 chg 0000 evt 0002
hub 2-6.3:1.0: state 7 ports 4 chg 0008 evt 0000
hub 2-6.3:1.0: port 3, status 0301, change 0000, 1.5 Mb/s
usb 2-6.3.3: new low speed USB device using ehci_hcd and address 11
hub 2-3.1.2:1.0: port 1: status 0101 change 0001
hub 2-3.1.2:1.0: port 2: status 0301 change 0001
usb 2-6.3.3: skipped 1 descriptor after interface
usb 2-6.3.3: skipped 1 descriptor after interface
usb 2-6.3.3: default language 0x0409
usb 2-6.3.3: udev 11, busnum 2, minor = 138
usb 2-6.3.3: New USB device found, idVendor=2222, idProduct=0013
usb 2-6.3.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 2-6.3.3: Product: Macally iKeySlim
usb 2-6.3.3: Manufacturer: Macally Peripherals
PM: Adding info for usb:2-6.3.3
usb 2-6.3.3: uevent
usb 2-6.3.3: usb_probe_device
usb 2-6.3.3: configuration #1 chosen from 1 choice
usb 2-6.3.3: uevent
usb 2-6.3.3: adding 2-6.3.3:1.0 (config #1, interface 0)
PM: Adding info for usb:2-6.3.3:1.0
usb 2-6.3.3:1.0: uevent
usbhid 2-6.3.3:1.0: usb_probe_interface
usbhid 2-6.3.3:1.0: usb_probe_interface - got id
PM: Adding info for hid:0003:2222:0013.0004
PM: Adding info for No Bus:input3
input: Macally Peripherals Macally iKeySlim as /devices/pci0000:00/0000:00:0b.1/usb2/2-6/2-6.3/2-6.3.3/2-6.3.3:1.0/input/input3
usb 2-6.3.3: link qh8-0e01/c1c92380 start 7 [1/2 us]
generic-usb 0003:2222:0013.0004: input: USB HID v1.10 Keyboard [Macally Peripherals Macally iKeySlim] on usb-0000:00:0b.1-6.3.3/input0
PM: Adding info for No Bus:ep_81
usb 2-6.3.3: adding 2-6.3.3:1.1 (config #1, interface 1)
PM: Adding info for usb:2-6.3.3:1.1
usb 2-6.3.3:1.1: uevent
usbhid 2-6.3.3:1.1: usb_probe_interface
usbhid 2-6.3.3:1.1: usb_probe_interface - got id
PM: Adding info for hid:0003:2222:0013.0005
PM: Adding info for No Bus:input4
input: Macally Peripherals Macally iKeySlim as /devices/pci0000:00/0000:00:0b.1/usb2/2-6/2-6.3/2-6.3.3/2-6.3.3:1.1/input/input4
usb 2-6.3.3: link qh8-0e01/c1c924c0 start 0 [1/2 us]
PM: Adding info for No Bus:mouse2
generic-usb 0003:2222:0013.0005: input: USB HID v1.10 Mouse [Macally Peripherals Macally iKeySlim] on usb-0000:00:0b.1-6.3.3/input1
PM: Adding info for No Bus:ep_82
PM: Adding info for No Bus:usbdev2.11
drivers/usb/core/inode.c: creating file '011'
PM: Adding info for No Bus:ep_00
hub 2-6.3:1.0: state 7 ports 4 chg 0000 evt 0008
usb 2-6.3.3: uevent
usb 2-3.1.2: link qh256-0001/c1c92540 start 9 [1/0 us]
hub 2-3.1.2:1.0: state 7 ports 4 chg 0006 evt 0000
hub 2-3.1.2:1.0: port 1, status 0101, change 0000, 12 Mb/s
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ohci_hcd 0000:00:0b.0: auto-stop root hub
usb 2-3.1.2.1: new high speed USB device using ehci_hcd and address 12
ata2.00: ATA-7: ST3250620AS, 3.AAC, max UDMA/133
ata2.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32)
hub 2-3.1.2:1.0: port 1 not reset yet, waiting 10ms
ata2.00: configured for UDMA/133
scsi 2:0:0:0: Direct-Access ATA ST3250620AS 3.AA PQ: 0 ANSI: 5
PM: Adding info for scsi:target2:0:0
PM: Adding info for scsi:2:0:0:0
PM: Adding info for No Bus:2:0:0:0
PM: Adding info for No Bus:2:0:0:0
usb 2-3.1.2.1: default language 0x0409
usb 2-3.1.2.1: udev 12, busnum 2, minor = 139
usb 2-3.1.2.1: New USB device found, idVendor=090c, idProduct=1000
usb 2-3.1.2.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-3.1.2.1: Product: DISK 2.0
usb 2-3.1.2.1: Manufacturer: USB
usb 2-3.1.2.1: SerialNumber: PHN84K6AD8PLXSVC
PM: Adding info for usb:2-3.1.2.1
usb 2-3.1.2.1: uevent
usb 2-3.1.2.1: usb_probe_device
usb 2-3.1.2.1: configuration #1 chosen from 1 choice
usb 2-3.1.2.1: adding 2-3.1.2.1:1.0 (config #1, interface 0)
PM: Adding info for usb:2-3.1.2.1:1.0
usb 2-3.1.2.1:1.0: uevent
usb-storage 2-3.1.2.1:1.0: usb_probe_interface
usb-storage 2-3.1.2.1:1.0: usb_probe_interface - got id
scsi5 : SCSI emulation for USB Mass Storage devices
PM: Adding info for scsi:host5
PM: Adding info for No Bus:host5
usb-storage: device found at 12
usb-storage: waiting for device to settle before scanning
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:ep_02
PM: Adding info for No Bus:usbdev2.12
drivers/usb/core/inode.c: creating file '012'
PM: Adding info for No Bus:ep_00
usb 2-3.1.2.1: uevent
usb 2-3.1.2.1: uevent
hub 2-3.1.2:1.0: port 2, status 0301, change 0000, 1.5 Mb/s
usb 2-3.1.2.2: new low speed USB device using ehci_hcd and address 13
hub 2-3.1.2:1.0: port 2 not reset yet, waiting 10ms
usb 2-3.1.2.2: skipped 1 descriptor after interface
usb 2-3.1.2.2: default language 0x0409
usb 2-3.1.2.2: udev 13, busnum 2, minor = 140
usb 2-3.1.2.2: New USB device found, idVendor=046d, idProduct=c050
usb 2-3.1.2.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 2-3.1.2.2: Product: USB-PS/2 Optical Mouse
usb 2-3.1.2.2: Manufacturer: Logitech
PM: Adding info for usb:2-3.1.2.2
usb 2-3.1.2.2: uevent
usb 2-3.1.2.2: usb_probe_device
usb 2-3.1.2.2: configuration #1 chosen from 1 choice
usb 2-3.1.2.2: adding 2-3.1.2.2:1.0 (config #1, interface 0)
PM: Adding info for usb:2-3.1.2.2:1.0
usb 2-3.1.2.2:1.0: uevent
usbhid 2-3.1.2.2:1.0: usb_probe_interface
usbhid 2-3.1.2.2:1.0: usb_probe_interface - got id
PM: Adding info for hid:0003:046D:C050.0006
usb 2-3.1.2.2: uevent
PM: Adding info for No Bus:input5
input: Logitech USB-PS/2 Optical Mouse as /devices/pci0000:00/0000:00:0b.1/usb2/2-3/2-3.1/2-3.1.2/2-3.1.2.2/2-3.1.2.2:1.0/input/input5
PM: Adding info for No Bus:mouse3
generic-usb 0003:046D:C050.0006: input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:0b.1-3.1.2.2/input0
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev2.13
drivers/usb/core/inode.c: creating file '013'
PM: Adding info for No Bus:ep_00
hub 2-3.1.2:1.0: state 7 ports 4 chg 0000 evt 0002
usb 2-3.1.2.2: uevent
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: ATAPI: ATAPI iHOS104, WL08, max UDMA/100
ata4.00: configured for UDMA/100
scsi 0:0:0:0: Direct-Access Generic USB SD Reader 1.00 PQ: 0 ANSI: 0
PM: Adding info for scsi:target0:0:0
PM: Adding info for scsi:0:0:0:0
PM: Adding info for No Bus:0:0:0:0
PM: Adding info for No Bus:0:0:0:0
scsi 0:0:0:1: Direct-Access Generic USB CF Reader 1.01 PQ: 0 ANSI: 0
PM: Adding info for scsi:0:0:0:1
PM: Adding info for No Bus:0:0:0:1
PM: Adding info for No Bus:0:0:0:1
scsi 0:0:0:2: Direct-Access Generic USB SM Reader 1.02 PQ: 0 ANSI: 0
PM: Adding info for scsi:0:0:0:2
PM: Adding info for No Bus:0:0:0:2
PM: Adding info for No Bus:0:0:0:2
scsi 0:0:0:3: Direct-Access Generic USB MS Reader 1.03 PQ: 0 ANSI: 0
PM: Adding info for scsi:0:0:0:3
PM: Adding info for No Bus:0:0:0:3
PM: Adding info for No Bus:0:0:0:3
usb-storage: device scan complete
PM: Adding info for No Bus:1:0:0:0
sd 1:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
PM: Adding info for No Bus:sda
sda:
PM: Adding info for No Bus:2:0:0:0
PM: Adding info for No Bus:0:0:0:0
PM: Adding info for No Bus:0:0:0:1
PM: Adding info for No Bus:0:0:0:2
sd 2:0:0:0: [sdb] 488397168 512-byte logical blocks: (250 GB/232 GiB)
PM: Adding info for No Bus:0:0:0:3
sd 2:0:0:0: [sdb] Write Protect is off
sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
PM: Adding info for No Bus:sdb
sdb:
PM: Adding info for No Bus:sdc
PM: Adding info for No Bus:8:32
PM: Adding info for No Bus:sdd
PM: Adding info for No Bus:8:48
sd 0:0:0:0: [sdc] Attached SCSI removable disk
sda1 sda2 sda3 <
PM: Adding info for No Bus:sde
PM: Adding info for No Bus:8:64
PM: Adding info for No Bus:sdf
PM: Adding info for No Bus:8:80
sd 0:0:0:1: [sdd] Attached SCSI removable disk
sd 0:0:0:2: [sde] Attached SCSI removable disk
sd 0:0:0:3: [sdf] Attached SCSI removable disk
unknown partition table
PM: Adding info for No Bus:8:16
sd 2:0:0:0: [sdb] Attached SCSI disk
>
PM: Adding info for No Bus:sda1
PM: Adding info for No Bus:sda2
PM: Adding info for No Bus:sda3
PM: Adding info for No Bus:8:0
sd 1:0:0:0: [sda] Attached SCSI disk
scsi 5:0:0:0: Direct-Access USB DISK 2.0 0403 PQ: 0 ANSI: 0 CCS
PM: Adding info for scsi:target5:0:0
PM: Adding info for scsi:5:0:0:0
PM: Adding info for No Bus:5:0:0:0
PM: Adding info for No Bus:5:0:0:0
PM: Adding info for No Bus:5:0:0:0
usb-storage: device scan complete
sd 5:0:0:0: [sdg] 3981312 512-byte logical blocks: (2.03 GB/1.89 GiB)
sd 5:0:0:0: [sdg] Write Protect is off
sd 5:0:0:0: [sdg] Mode Sense: 43 00 00 00
sd 5:0:0:0: [sdg] Assuming drive cache: write through
PM: Adding info for No Bus:sdg
sd 5:0:0:0: [sdg] Assuming drive cache: write through
sdg: sdg1
PM: Adding info for No Bus:sdg1
PM: Adding info for No Bus:8:96
sd 5:0:0:0: [sdg] Assuming drive cache: write through
sd 5:0:0:0: [sdg] Attached SCSI removable disk
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 60 00
ata4.00: cmd a0/01:00:00:60:00/00:00:00:00:00/a0 tag 0 dma 96 in
res 40/00:02:00:24:00/00:00:00:00:00/a0 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for UDMA/100
ata4: EH complete
ata4: limiting SATA link speed to 1.5 Gbps
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 60 00
ata4.00: cmd a0/01:00:00:60:00/00:00:00:00:00/a0 tag 0 dma 96 in
res 40/00:02:00:24:00/00:00:00:00:00/a0 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for UDMA/100
ata4: EH complete
ata4.00: limiting speed to UDMA/66:PIO4
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 60 00
ata4.00: cmd a0/01:00:00:60:00/00:00:00:00:00/a0 tag 0 dma 96 in
res 40/00:02:00:24:00/00:00:00:00:00/a0 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for UDMA/66
ata4: EH complete
ata4.00: limiting speed to UDMA/33:PIO4
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
scsi 4:0:0:0: CDB: Inquiry: 12 00 00 00 60 00
ata4.00: cmd a0/01:00:00:60:00/00:00:00:00:00/a0 tag 0 dma 96 in
res 40/00:02:00:24:00/00:00:00:00:00/a0 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for UDMA/33
scsi scan: 96 byte inquiry failed. Consider BLIST_INQUIRY_36 for this device
ata4: EH complete
scsi 4:0:0:0: CD-ROM ATAPI iHOS104 WL08 PQ: 0 ANSI: 5
PM: Adding info for scsi:target4:0:0
PM: Adding info for scsi:4:0:0:0
PM: Adding info for No Bus:4:0:0:0
PM: Adding info for No Bus:4:0:0:0
usb 2-2:1.0: uevent
usb 2-2: uevent
usb 2-2:1.0: uevent
usb 2-2: uevent
usb 2-2:1.0: uevent
usb 2-2: uevent
usb 2-2:1.0: uevent
usb 2-2: uevent
usb 2-3.1.2.1:1.0: uevent
usb 2-3.1.2.1: uevent
usb 2-2:1.0: uevent
usb 2-3.1.2.1:1.0: uevent
usb 2-2:1.0: uevent
usb 2-2:1.0: uevent
usb 2-2:1.0: uevent
ide-cd driver 5.00
PM: Adding info for No Bus:0.0
ide-cd: hda: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2000kB Cache
Uniform CD-ROM driver Revision: 3.20
PM: Adding info for No Bus:hda
PM: Adding info for No Bus:3:0
usb 2-3.1.2.1:1.0: uevent
usb 2-3.1.2.1: uevent
usb 2-3.1.2.1:1.0: uevent
PM: Adding info for No Bus:device-mapper
device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
PM: Adding info for No Bus:dm-0
PM: Adding info for No Bus:254:0
PM: Adding info for No Bus:dm-1
PM: Adding info for No Bus:dm-2
PM: Adding info for No Bus:254:2
PM: Adding info for No Bus:254:1
PM: Adding info for No Bus:dm-3
PM: Adding info for No Bus:254:3
PM: Adding info for No Bus:dm-4
PM: Adding info for No Bus:254:4
PM: Adding info for No Bus:dm-5
PM: Adding info for No Bus:254:5
PM: Removing info for No Bus:254:1
PM: Removing info for No Bus:dm-1
PM: Adding info for No Bus:dm-1
PM: Adding info for No Bus:254:1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
xor: automatically using best checksumming function: pIII_sse
pIII_sse : 7516.000 MB/sec
xor: using function: pIII_sse (7516.000 MB/sec)
raid6: int32x1 878 MB/s
raid6: int32x2 839 MB/s
raid6: int32x4 703 MB/s
raid6: int32x8 585 MB/s
raid6: mmxx1 2742 MB/s
raid6: mmxx2 3167 MB/s
raid6: sse1x1 1890 MB/s
raid6: sse1x2 2441 MB/s
raid6: sse2x1 3546 MB/s
raid6: sse2x2 4222 MB/s
raid6: using algorithm sse2x2 (4222 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
md: raid10 personality registered for level 10
PM: Marking nosave pages: 000000000009c000 - 0000000000100000
PM: Basic memory bitmaps created
PM: Basic memory bitmaps freed
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with writeback data mode.
udev: starting version 146
usb usb1: uevent
usb 1-0:1.0: uevent
usb usb2: uevent
usb 2-0:1.0: uevent
usb 2-2: uevent
usb 2-2:1.0: uevent
usb 2-3: uevent
usb 2-3.1: uevent
usb 2-3.1.1: uevent
usb 2-3.1.1:1.0: uevent
usb 2-3.1.1:1.1: uevent
usb 2-3.1.2: uevent
usb 2-3.1.2.1: uevent
usb 2-3.1.2.1:1.0: uevent
usb 2-3.1.2.2: uevent
usb 2-3.1.2.2:1.0: uevent
usb 2-3.1.2:1.0: uevent
usb 2-3.1:1.0: uevent
usb 2-3:1.0: uevent
usb 2-6: uevent
usb 2-6.1: uevent
usb 2-6.1:1.0: uevent
usb 2-6.3: uevent
usb 2-6.3.3: uevent
usb 2-6.3.3:1.0: uevent
usb 2-6.3.3:1.1: uevent
usb 2-6.3:1.0: uevent
usb 2-6:1.0: uevent
usb usb1: uevent
usb usb2: uevent
usb usb2: uevent
usb usb1: uevent
PM: Adding info for No Bus:input6
input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input6
ACPI: Power Button [PWRB]
PM: Adding info for No Bus:input7
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input7
ACPI: Power Button [PWRF]
usb 2-6: uevent
usb 2-3: uevent
usb 2-2: uevent
usb 2-3: uevent
usb 2-2: uevent
usb 2-2:1.0: uevent
usb 2-2: uevent
ACPI: SSDT 7fefa940 00175 (v01 Nvidia ASUSACPI 42302E31 AWRD 00000000)
PM: Adding info for No Bus:cooling_device1
processor LNXCPU:00: registered as cooling_device1
ACPI: SSDT 7fefad50 000CE (v01 Nvidia ASUSACPI 42302E31 AWRD 00000000)
PM: Adding info for No Bus:cooling_device2
processor LNXCPU:01: registered as cooling_device2
usb 2-2:1.0: uevent
usb 2-2: uevent
usb 2-2:1.0: uevent
usb 2-2: uevent
usb 2-2:1.0: uevent
usb 2-2: uevent
usb 2-6: uevent
usb 2-2:1.0: uevent
usb 2-2:1.0: uevent
usb 2-2:1.0: uevent
usb 2-6.3: uevent
usb 2-6.1: uevent
usb 2-3.1: uevent
usb 2-6.3: uevent
usb 2-2:1.0: uevent
usb 2-6.1: uevent
usb 2-3.1: uevent
usb 2-3.1.2: uevent
usb 2-3.1.1: uevent
usb 2-3.1.2: uevent
usb 2-6.3.3: uevent
usb 2-3.1.1: uevent
usb 2-3.1.2.1: uevent
usb 2-3.1.2.2: uevent
usb 2-6.3.3: uevent
usb 2-3.1.2.1:1.0: uevent
usb 2-3.1.2.1: uevent
usb 2-3.1.2.2: uevent
usb 2-3.1.2.1: uevent
usb 2-3.1.2.1:1.0: uevent
PM: Adding info for No Bus:rtc
Real Time Clock Driver v1.12b
PM: Adding info for No Bus:hwmon0
PM: Adding info for No Bus:event0
PM: Adding info for No Bus:event1
PM: Adding info for No Bus:event2
PM: Adding info for No Bus:event3
PM: Adding info for No Bus:event4
PM: Adding info for No Bus:event5
PM: Adding info for No Bus:event6
PM: Adding info for No Bus:event7
usb 2-3.1.2.2:1.0: uevent
usb 2-3.1.2.2: uevent
usb 2-3.1.2.2:1.0: uevent
usb 2-3.1.2.2: uevent
usb 2-6.3.3:1.0: uevent
usb 2-6.3.3: uevent
usb 2-3.1.2.2:1.0: uevent
usb 2-3.1.2.2:1.0: uevent
usb 2-6.3.3:1.0: uevent
PM: Adding info for No Bus:raw1394
ieee1394: raw1394: /dev/raw1394 device initialized
ACPI: I/O resource nForce2_smbus [0x5000-0x503f] conflicts with ACPI region SM00 [0x5000-0x5005]
ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
nForce2_smbus 0000:00:0a.1: Error probing SMB1.
PM: Adding info for i2c:i2c-0
i2c i2c-0: nForce2 SMBus adapter at 0x5100
usb 2-6.1:1.0: uevent
usb 2-6.1: uevent
usb 2-6.1:1.0: uevent
usb 2-6.1: uevent
usb 2-6.1:1.0: uevent
usb 2-6.1:1.0: uevent
usb 2-6.3.3:1.1: uevent
usb 2-6.3.3: uevent
usb 2-3.1.1:1.1: uevent
usb 2-3.1.1: uevent
usb 2-6.3.3:1.1: uevent
usb 2-3.1.1:1.0: uevent
usb 2-3.1.1: uevent
usb 2-6.3.3:1.1: uevent
usb 2-3.1.1:1.1: uevent
usb 2-3.1.1: uevent
usb 2-6.3.3: uevent
usb 2-3.1.1:1.1: uevent
usb 2-3.1.1:1.1: uevent
usb 2-3.1.1:1.0: uevent
usb 2-6.3.3:1.1: uevent
PM: Adding info for No Bus:dv1394-0
PM: Adding info for No Bus:timer
PM: Adding info for No Bus:seq
hda: UDMA/66 mode selected
hda: task_no_data_intr: status=0x41 { DriveReady Error }
hda: task_no_data_intr: error=0x04 { AbortedCommand }
hda: possibly failed opcode: 0xe3
PM: Adding info for No Bus:sequencer
PM: Adding info for No Bus:sequencer2
ACPI: PCI Interrupt Link [AAZA] enabled at IRQ 23
HDA Intel 0000:00:10.1: PCI INT B -> Link[AAZA] -> GSI 23 (level, low) -> IRQ 23
HDA Intel 0000:00:10.1: setting latency timer to 64
PM: Adding info for No Bus:input8
input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:10.1/input/input8
PM: Adding info for No Bus:event8
PM: Adding info for No Bus:card0
PM: Adding info for No Bus:pcmC0D1p
PM: Adding info for No Bus:adsp
PM: Adding info for No Bus:pcmC0D0p
PM: Adding info for No Bus:pcmC0D0c
PM: Adding info for No Bus:dsp
PM: Adding info for No Bus:audio
PM: Adding info for No Bus:hwC0D0
PM: Adding info for No Bus:controlC0
PM: Adding info for No Bus:mixer
ata4.00: limiting speed to PIO4
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
sr 4:0:0:0: CDB: Mode Sense(10): 5a 00 2a 00 00 00 00 00 80 00
ata4.00: cmd a0/01:00:00:80:00/00:00:00:00:00/a0 tag 0 dma 16512 in
res 40/00:03:00:00:00/00:00:00:00:00/a0 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO4
ata4: EH complete
sr0: scsi3-mmc drive: 32x/32x cd/rw xa/form2 cdda tray
PM: Adding info for No Bus:sr0
PM: Adding info for No Bus:11:0
sr 4:0:0:0: Attached scsi CD-ROM sr0
PM: Adding info for No Bus:sg0
sd 1:0:0:0: Attached scsi generic sg0 type 0
PM: Adding info for No Bus:sg1
sd 2:0:0:0: Attached scsi generic sg1 type 0
PM: Adding info for No Bus:sg2
sd 0:0:0:0: Attached scsi generic sg2 type 0
PM: Adding info for No Bus:sg3
sd 0:0:0:1: Attached scsi generic sg3 type 0
PM: Adding info for No Bus:sg4
sd 0:0:0:2: Attached scsi generic sg4 type 0
PM: Adding info for No Bus:sg5
sd 0:0:0:3: Attached scsi generic sg5 type 0
PM: Adding info for No Bus:sg6
sd 5:0:0:0: Attached scsi generic sg6 type 0
PM: Adding info for No Bus:sg7
sr 4:0:0:0: Attached scsi generic sg7 type 5
PM: Adding info for No Bus:vcs2
PM: Adding info for No Bus:vcsa2
PM: Adding info for No Bus:vcs3
PM: Adding info for No Bus:vcsa3
PM: Adding info for No Bus:vcs4
PM: Adding info for No Bus:vcsa4
PM: Adding info for No Bus:vcs5
PM: Adding info for No Bus:vcsa5
PM: Adding info for No Bus:vcs6
PM: Adding info for No Bus:vcsa6
hda: UDMA/66 mode selected
hda: task_no_data_intr: status=0x41 { DriveReady Error }
hda: task_no_data_intr: error=0x04 { AbortedCommand }
hda: possibly failed opcode: 0xe3
EXT3 FS on dm-2, internal journal
i2c /dev entries driver
PM: Adding info for No Bus:i2c-0
it87: Found IT8712F chip at 0x290, revision 7
it87: in3 is VCC (+5V)
it87: in7 is VCCH (+5V Stand-By)
ACPI: I/O resource it87 [0x295-0x296] conflicts with ACPI region HWRE [0x295-0x296]
ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
fuse init (API version 7.13)
PM: Adding info for No Bus:fuse
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-5, internal journal
EXT3-fs: mounted filesystem with writeback data mode.
PM: Adding info for No Bus:254:3-fuseblk
PM: Adding info for No Bus:254:1-fuseblk
Adding 4194296k swap on /mnt/oldlin/4G-memory.swap. Priority:-1 extents:1057 across:4264956k
r8169: eth1: link up
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PM: Adding info for No Bus:0:16
PM: Adding info for No Bus:0:17
PM: Adding info for No Bus:0:18
PM: Adding info for No Bus:vcs10
PM: Adding info for No Bus:vcsa10
usb 2-6.1: link qh8-0e01/c216bac0 start 2 [1/2 us]
usb 2-3.1.2.2: link qh8-0e01/c216bd00 start 3 [1/2 us]
usb 2-6.1: unlink qh8-0e01/c216bac0 start 2 [1/2 us]
usb 2-3.1.2.2: unlink qh8-0e01/c216bd00 start 3 [1/2 us]
ehci_hcd 0000:00:0b.1: reused qh c216bac0 schedule
usb 2-6.1: link qh8-0e01/c216bac0 start 2 [1/2 us]
ehci_hcd 0000:00:0b.1: reused qh c216bd00 schedule
usb 2-3.1.2.2: link qh8-0e01/c216bd00 start 3 [1/2 us]
irda_init()
NET: Registered protocol family 23
usbcore: registered new interface driver stir4200
usb 2-2:1.0: uevent
usb 2-2: uevent
usb 2-2:1.0: uevent
usb 2-2:1.0: uevent
usb 2-2: uevent
usb 2-2:1.0: uevent
usb 2-2:1.0: uevent
usb 2-2: uevent
usb 2-2:1.0: uevent
usb 2-2:1.0: uevent
usb 2-2: uevent
usb 2-2:1.0: uevent
usb 2-3.1.2.1:1.0: uevent
usb 2-3.1.2.1: uevent
usb 2-3.1.2.1:1.0: uevent
warning: `ntpd' uses 32-bit capabilities (legacy support in use)
usb usb1: uevent
usb 1-0:1.0: uevent
usb usb2: uevent
usb 2-0:1.0: uevent
usb 2-2: uevent
usb 2-2:1.0: uevent
usb 2-3: uevent
usb 2-3.1: uevent
usb 2-3.1.1: uevent
usb 2-3.1.1:1.0: uevent
usb 2-3.1.1:1.1: uevent
usb 2-3.1.2: uevent
usb 2-3.1.2.1: uevent
usb 2-3.1.2.1:1.0: uevent
usb 2-3.1.2.2: uevent
usb 2-3.1.2.2:1.0: uevent
usb 2-3.1.2:1.0: uevent
usb 2-3.1:1.0: uevent
usb 2-3:1.0: uevent
usb 2-6: uevent
usb 2-6.1: uevent
usb 2-6.1:1.0: uevent
usb 2-6.3: uevent
usb 2-6.3.3: uevent
usb 2-6.3.3:1.0: uevent
usb 2-6.3.3:1.1: uevent
usb 2-6.3:1.0: uevent
usb 2-6:1.0: uevent
Bluetooth: Core ver 2.15
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.14
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM ver 1.11
Bluetooth: SCO (Voice Link) ver 0.6
Bluetooth: SCO socket layer initialized
CPUFREQ: Per core ondemand sysfs interface is deprecated - up_threshold
CPUFREQ: Per core ondemand sysfs interface is deprecated - ignore_nice_load
PM: Adding info for No Bus:vcs7
PM: Adding info for No Bus:vcsa7
Linux agpgart interface v0.103
nvidia: module license 'NVIDIA' taints kernel.
Disabling lock debugging due to kernel taint
ACPI: PCI Interrupt Link [APC5] enabled at IRQ 16
nvidia 0000:01:00.0: PCI INT A -> Link[APC5] -> GSI 16 (level, low) -> IRQ 16
nvidia 0000:01:00.0: setting latency timer to 64
NVRM: loading NVIDIA UNIX x86 Kernel Module 185.18.36 Fri Aug 14 17:18:04 PDT 2009
PM: Adding info for i2c:i2c-1
PM: Adding info for No Bus:i2c-1
PM: Adding info for i2c:i2c-2
PM: Adding info for No Bus:i2c-2
PM: Adding info for i2c:i2c-3
PM: Adding info for No Bus:i2c-3
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: sata_nv times out for BD-ROM iHOS104-08
2010-02-21 21:28 ` Cengiz Günay
@ 2010-02-23 2:38 ` Tejun Heo
2010-02-28 17:24 ` Cengiz Günay
0 siblings, 1 reply; 28+ messages in thread
From: Tejun Heo @ 2010-02-23 2:38 UTC (permalink / raw)
To: Cengiz Günay; +Cc: Robert Hancock, linux-kernel, linux-ide
[-- Attachment #1: Type: text/plain, Size: 787 bytes --]
Hello,
On 02/22/2010 06:28 AM, Cengiz Günay wrote:
> On Sat, Feb 20, 2010 at 8:01 PM, Tejun Heo <tj@kernel.org> wrote:
>> Hmmm... So, DRQ gets cleared? That's strange. When then the 18 extra
>> bytes happen? Can you please try this one?
>
> It worked!
>
> $ lsscsi
> ...
> [4:0:0:0] cd/dvd ATAPI iHOS104 WL08 /dev/sr0
> ...
>
> I was able to read a regular DVD in the drive. According to dmesg the
> negotiated speed was down to UDMA/33, so I am not sure about the
> performance of the drive.
Hmmm.... it could be that the drive is sending more data then
requested and the state machine in the controller doesn't like that
and fails to assert IRQ on the host side. You're still getting
timeouts on 96 byte dma inquiries. Can you please this patch?
--
tejun
[-- Attachment #2: swncq-atapi-pio.patch --]
[-- Type: text/x-patch, Size: 1704 bytes --]
diff --git a/drivers/ata/sata_nv.c b/drivers/ata/sata_nv.c
index 0c82d33..4ad76f1 100644
--- a/drivers/ata/sata_nv.c
+++ b/drivers/ata/sata_nv.c
@@ -307,6 +307,7 @@ static int nv_scr_write(struct ata_link *link, unsigned int sc_reg, u32 val);
static int nv_hardreset(struct ata_link *link, unsigned int *class,
unsigned long deadline);
+static int nv_check_atapi_dma(struct ata_queued_cmd *qc);
static void nv_nf2_freeze(struct ata_port *ap);
static void nv_nf2_thaw(struct ata_port *ap);
static void nv_ck804_freeze(struct ata_port *ap);
@@ -470,6 +471,7 @@ static struct ata_port_operations nv_generic_ops = {
.scr_read = nv_scr_read,
.scr_write = nv_scr_write,
.hardreset = nv_hardreset,
+ .check_atapi_dma = nv_check_atapi_dma,
};
static struct ata_port_operations nv_nf2_ops = {
@@ -585,7 +587,7 @@ static const struct ata_port_info nv_port_info[] = {
/* SWNCQ */
{
.flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
- ATA_FLAG_NCQ,
+ ATA_FLAG_NCQ | ATA_FLAG_PIO_POLLING,
.pio_mask = NV_PIO_MASK,
.mwdma_mask = NV_MWDMA_MASK,
.udma_mask = NV_UDMA_MASK,
@@ -1614,6 +1616,24 @@ static int nv_hardreset(struct ata_link *link, unsigned int *class,
return -EAGAIN;
}
+#include <scsi/scsi_cmnd.h>
+static int nv_check_atapi_dma(struct ata_queued_cmd *qc)
+{
+ /* Whitelist commands that may use DMA. */
+ switch (qc->scsicmd->cmnd[0]) {
+ case WRITE_12:
+ case WRITE_10:
+ case WRITE_6:
+ case READ_12:
+ case READ_10:
+ case READ_6:
+ case 0xad: /* READ_DVD_STRUCTURE */
+ case 0xbe: /* READ_CD */
+ return 0;
+ }
+ return 1;
+}
+
static void nv_nf2_freeze(struct ata_port *ap)
{
void __iomem *scr_addr = ap->host->ports[0]->ioaddr.scr_addr;
^ permalink raw reply related [flat|nested] 28+ messages in thread
* Re: sata_nv times out for BD-ROM iHOS104-08
2010-02-23 2:38 ` Tejun Heo
@ 2010-02-28 17:24 ` Cengiz Günay
2010-03-02 11:48 ` Tejun Heo
0 siblings, 1 reply; 28+ messages in thread
From: Cengiz Günay @ 2010-02-28 17:24 UTC (permalink / raw)
To: Tejun Heo; +Cc: Robert Hancock, linux-kernel, linux-ide
[-- Attachment #1: Type: text/plain, Size: 1068 bytes --]
Hi Tejun,
On Mon, Feb 22, 2010 at 9:38 PM, Tejun Heo <tj@kernel.org> wrote:
> On 02/22/2010 06:28 AM, Cengiz Günay wrote:
>> I was able to read a regular DVD in the drive. According to dmesg the
>> negotiated speed was down to UDMA/33, so I am not sure about the
>> performance of the drive.
>
> Hmmm.... it could be that the drive is sending more data then
> requested and the state machine in the controller doesn't like that
> and fails to assert IRQ on the host side. You're still getting
> timeouts on 96 byte dma inquiries. Can you please this patch?
Before and after the swncq-atapi-pio patch I still get awful read
times from the BD-ROM drive:
$ time dd if=/dev/sr0 of=/dev/null bs=64k count=1024
67108864 bytes (67 MB) copied, 106.945 seconds, 628 kB/s
=> real 1m46.977s
Compared to reading the same DVD in my DVD-ROM drive:
$ time dd if=/dev/hda of=/dev/null bs=64k count=1024
67108864 bytes (67 MB) copied, 13.8403 seconds, 4.8 MB/s
=> real 0m13.860s
I attached the full dmesg after the swncq-atapi-pio patch.
-Cengiz
[-- Attachment #2: dmesg-sata_nv-swncq-atapi-pio-patch-2 --]
[-- Type: application/octet-stream, Size: 88514 bytes --]
Linux version 2.6.32testing (root@salon) (gcc version 4.3.3 (Debian 4.3.3-10) ) #5 SMP PREEMPT Sat Feb 27 13:00:31 EST 2010
KERNEL supported cpus:
Intel GenuineIntel
AMD AuthenticAMD
NSC Geode by NSC
Cyrix CyrixInstead
Centaur CentaurHauls
Transmeta GenuineTMx86
Transmeta TransmetaCPU
UMC UMC UMC UMC
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009c400 (usable)
BIOS-e820: 000000000009c400 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000007fef0000 (usable)
BIOS-e820: 000000007fef0000 - 000000007fef3000 (ACPI NVS)
BIOS-e820: 000000007fef3000 - 000000007ff00000 (ACPI data)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
DMI 2.4 present.
Phoenix BIOS detected: BIOS may corrupt low RAM, working around it.
e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
last_pfn = 0x7fef0 max_arch_pfn = 0x100000
MTRR default type: uncachable
MTRR fixed ranges enabled:
00000-9FFFF write-back
A0000-BFFFF uncachable
C0000-CDFFF write-protect
CE000-FFFFF uncachable
MTRR variable ranges enabled:
0 base 000000000 mask F80000000 write-back
1 base 07FF00000 mask FFFF00000 uncachable
2 disabled
3 disabled
4 disabled
5 disabled
6 disabled
7 disabled
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
initial memory mapped : 0 - 01800000
init_memory_mapping: 0000000000000000-00000000377fe000
0000000000 - 0000400000 page 4k
0000400000 - 0037400000 page 2M
0037400000 - 00377fe000 page 4k
kernel direct mapping tables up to 377fe000 @ 10000-15000
RAMDISK: 36bad000 - 37fef321
Allocated new RAMDISK: 013e6000 - 02828321
Move RAMDISK from 0000000036bad000 - 0000000037fef320 to 013e6000 - 02828320
ACPI: RSDP 000f7900 00024 (v02 Nvidia)
ACPI: XSDT 7fef30c0 0004C (v01 Nvidia ASUSACPI 42302E31 AWRD 00000000)
ACPI: FACP 7fefa600 000F4 (v03 Nvidia ASUSACPI 42302E31 AWRD 00000000)
ACPI: DSDT 7fef3240 07354 (v01 NVIDIA ASUSACPI 00001000 MSFT 03000000)
ACPI: FACS 7fef0000 00040
ACPI: HPET 7fefa840 00038 (v01 Nvidia ASUSACPI 42302E31 AWRD 00000098)
ACPI: MCFG 7fefa8c0 0003C (v01 Nvidia ASUSACPI 42302E31 AWRD 00000000)
ACPI: APIC 7fefa740 0008E (v01 Nvidia ASUSACPI 42302E31 AWRD 00000000)
ACPI: SSDT 7fefae20 0032C (v01 Nvidia ASUSACPI 42302E31 AWRD 00000000)
ACPI: Local APIC address 0xfee00000
1158MB HIGHMEM available.
887MB LOWMEM available.
mapped low ram: 0 - 377fe000
low ram: 0 - 377fe000
node 0 low ram: 00000000 - 377fe000
node 0 bootmap 00011000 - 00017f00
(9 early reservations) ==> bootmem [0000000000 - 00377fe000]
#0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
#1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000]
#2 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 - 0000007000]
#3 [0001000000 - 00013de7c4] TEXT DATA BSS ==> [0001000000 - 00013de7c4]
#4 [000009c400 - 0000100000] BIOS reserved ==> [000009c400 - 0000100000]
#5 [00013df000 - 00013e5149] BRK ==> [00013df000 - 00013e5149]
#6 [0000010000 - 0000011000] PGTABLE ==> [0000010000 - 0000011000]
#7 [00013e6000 - 0002828321] NEW RAMDISK ==> [00013e6000 - 0002828321]
#8 [0000011000 - 0000018000] BOOTMAP ==> [0000011000 - 0000018000]
found SMP MP-table at [c00f5d50] f5d50
Zone PFN ranges:
DMA 0x00000010 -> 0x00001000
Normal 0x00001000 -> 0x000377fe
HighMem 0x000377fe -> 0x0007fef0
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
0: 0x00000010 -> 0x0000009c
0: 0x00000100 -> 0x0007fef0
On node 0 totalpages: 523900
free_area_init_node: node 0, pgdat c1324fc0, node_mem_map c282a200
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 3948 pages, LIFO batch:0
Normal zone: 1744 pages used for memmap
Normal zone: 221486 pages, LIFO batch:31
HighMem zone: 2318 pages used for memmap
HighMem zone: 294372 pages, LIFO batch:31
Using APIC driver default
ACPI: PM-Timer IO Port: 0x4008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 4, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
ACPI: IRQ9 used by override.
ACPI: IRQ14 used by override.
ACPI: IRQ15 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
ACPI: HPET id: 0x10de8201 base: 0xfeff0000
SMP: Allowing 4 CPUs, 2 hotplug CPUs
nr_irqs_gsi: 24
PM: Registered nosave memory: 000000000009c000 - 000000000009d000
PM: Registered nosave memory: 000000000009d000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
Allocating PCI resources starting at 7ff00000 (gap: 7ff00000:60100000)
NR_CPUS:4 nr_cpumask_bits:4 nr_cpu_ids:4 nr_node_ids:1
PERCPU: Embedded 11 pages/cpu @c3c00000 s23512 r0 d21544 u1048576
pcpu-alloc: s23512 r0 d21544 u1048576 alloc=1*4194304
pcpu-alloc: [0] 0 1 2 3
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 519806
Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.32testing root=/dev/mapper/nvidia_ceebaiib1 ro
PID hash table entries: 4096 (order: 2, 16384 bytes)
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
Initializing HighMem for node 0 (000377fe:0007fef0)
Memory: 2052264k/2096064k available (2319k kernel code, 42160k reserved, 912k data, 404k init, 1186760k highmem)
virtual kernel memory layout:
fixmap : 0xfff6b000 - 0xfffff000 ( 592 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xf7ffe000 - 0xff7fe000 ( 120 MB)
lowmem : 0xc0000000 - 0xf77fe000 ( 887 MB)
.init : 0xc1329000 - 0xc138e000 ( 404 kB)
.data : 0xc1243e41 - 0xc1328128 ( 912 kB)
.text : 0xc1000000 - 0xc1243e41 (2319 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:384
Extended CMOS year: 2000
spurious 8259A interrupt: IRQ7.
Console: colour VGA+ 80x25
console [tty0] enabled
hpet clockevent registered
Fast TSC calibration using PIT
Detected 2133.538 MHz processor.
Calibrating delay loop (skipped), value calculated using timer frequency.. 4267.07 BogoMIPS (lpj=2133538)
Security Framework initialized
Mount-cache hash table entries: 512
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
mce: CPU supports 6 MCE banks
CPU0: Thermal monitoring enabled (TM2)
using mwait in idle threads.
Checking 'hlt' instruction... OK.
ACPI: Core revision 20090903
..TIMER: vector=0x30 apic1=0 pin1=0 apic2=-1 pin2=-1
..MP-BIOS bug: 8254 timer not connected to IO-APIC
...trying to set up timer (IRQ0) through the 8259A ...
..... (found apic 0 pin 0) ...
....... works.
CPU0: Intel(R) Core(TM)2 CPU 6400 @ 2.13GHz stepping 06
Booting processor 1 APIC 0x1 ip 0x6000
Initializing CPU#1
Calibrating delay using timer specific routine.. 4266.57 BogoMIPS (lpj=2133289)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU1: Thermal monitoring enabled (TM2)
CPU1: Intel(R) Core(TM)2 CPU 6400 @ 2.13GHz stepping 06
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Brought up 2 CPUs
Total of 2 processors activated (8533.65 BogoMIPS).
CPU0 attaching sched-domain:
domain 0: span 0-1 level MC
groups: 0 1
CPU1 attaching sched-domain:
domain 0: span 0-1 level MC
groups: 1 0
PM: Adding info for No Bus:platform
Time: 11:40:04 Date: 02/28/10
NET: Registered protocol family 16
PM: Adding info for No Bus:vtcon0
EISA bus registered
ACPI: bus type pci registered
PM: Adding info for No Bus:id
PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
PCI: MCFG area at e0000000 reserved in E820
PCI: Using MMCONFIG for extended config space
PCI: Using configuration type 1 for base access
PM: Adding info for No Bus:default
bio: create slab <bio-0> at 0
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
PM: Adding info for acpi:LNXSYSTM:00
PM: Adding info for acpi:LNXCPU:00
PM: Adding info for acpi:LNXCPU:01
PM: Adding info for acpi:LNXCPU:02
PM: Adding info for acpi:LNXCPU:03
PM: Adding info for acpi:LNXSYBUS:00
PM: Adding info for acpi:PNP0C0C:00
PM: Adding info for acpi:PNP0A08:00
PM: Adding info for acpi:PNP0C02:00
PM: Adding info for acpi:device:00
PM: Adding info for acpi:device:01
PM: Adding info for acpi:device:02
PM: Adding info for acpi:device:03
PM: Adding info for acpi:device:04
PM: Adding info for acpi:device:05
PM: Adding info for acpi:device:06
PM: Adding info for acpi:device:07
PM: Adding info for acpi:device:08
PM: Adding info for acpi:device:09
PM: Adding info for acpi:device:0a
PM: Adding info for acpi:device:0b
PM: Adding info for acpi:device:0c
PM: Adding info for acpi:device:0d
PM: Adding info for acpi:device:0e
PM: Adding info for acpi:device:0f
PM: Adding info for acpi:device:10
PM: Adding info for acpi:device:11
PM: Adding info for acpi:device:12
PM: Adding info for acpi:device:13
PM: Adding info for acpi:device:14
PM: Adding info for acpi:device:15
PM: Adding info for acpi:device:16
PM: Adding info for acpi:device:17
PM: Adding info for acpi:device:18
PM: Adding info for acpi:device:19
PM: Adding info for acpi:PNP0C02:01
PM: Adding info for acpi:PNP0000:00
PM: Adding info for acpi:PNP0200:00
PM: Adding info for acpi:PNP0100:00
PM: Adding info for acpi:PNP0103:00
PM: Adding info for acpi:PNP0B00:00
PM: Adding info for acpi:PNP0800:00
PM: Adding info for acpi:PNP0C04:00
PM: Adding info for acpi:device:1a
PM: Adding info for acpi:device:1b
PM: Adding info for acpi:device:1c
PM: Adding info for acpi:device:1d
PM: Adding info for acpi:device:1e
PM: Adding info for acpi:device:1f
PM: Adding info for acpi:NVRAIDBUS:00
PM: Adding info for acpi:ATK0110:00
PM: Adding info for acpi:PNP0C0F:00
PM: Adding info for acpi:PNP0C0F:01
PM: Adding info for acpi:PNP0C0F:02
PM: Adding info for acpi:PNP0C0F:03
PM: Adding info for acpi:PNP0C0F:04
PM: Adding info for acpi:PNP0C0F:05
PM: Adding info for acpi:PNP0C0F:06
PM: Adding info for acpi:PNP0C0F:07
PM: Adding info for acpi:PNP0C0F:08
PM: Adding info for acpi:PNP0C0F:09
PM: Adding info for acpi:PNP0C0F:0a
PM: Adding info for acpi:PNP0C0F:0b
PM: Adding info for acpi:PNP0C0F:0c
PM: Adding info for acpi:PNP0C0F:0d
PM: Adding info for acpi:PNP0C0F:0e
PM: Adding info for acpi:PNP0C0F:0f
PM: Adding info for acpi:PNP0C0F:10
PM: Adding info for acpi:PNP0C0F:11
PM: Adding info for acpi:PNP0C0F:12
PM: Adding info for acpi:PNP0C0F:13
PM: Adding info for acpi:PNP0C0F:14
PM: Adding info for acpi:PNP0C0F:15
PM: Adding info for acpi:PNP0C0F:16
PM: Adding info for acpi:PNP0C0F:17
PM: Adding info for acpi:PNP0C0F:18
PM: Adding info for acpi:PNP0C0F:19
PM: Adding info for acpi:PNP0C0F:1a
PM: Adding info for acpi:PNP0C0F:1b
PM: Adding info for acpi:PNP0C0F:1c
PM: Adding info for acpi:PNP0C0F:1d
PM: Adding info for acpi:PNP0C0F:1e
PM: Adding info for acpi:PNP0C0F:1f
PM: Adding info for acpi:PNP0C0F:20
PM: Adding info for acpi:PNP0C0F:21
PM: Adding info for acpi:PNP0C0F:22
PM: Adding info for acpi:PNP0C0F:23
PM: Adding info for acpi:PNP0C0F:24
PM: Adding info for acpi:PNP0C0F:25
PM: Adding info for acpi:PNP0C0F:26
PM: Adding info for acpi:PNP0C0F:27
PM: Adding info for acpi:PNP0C0F:28
PM: Adding info for acpi:PNP0C02:02
PM: Adding info for acpi:PNP0C01:00
PM: Adding info for acpi:LNXTHERM:00
PM: Adding info for acpi:PNP0C0B:00
PM: Adding info for acpi:LNXTHERM:01
PM: Adding info for acpi:LNXPWRBN:00
ACPI: No dock devices found.
ACPI: PCI Root Bridge [PCI0] (0000:00)
PM: Adding info for No Bus:pci0000:00
PM: Adding info for No Bus:0000:00
pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:02.0: PME# disabled
pci 0000:00:04.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:04.0: PME# disabled
pci 0000:00:05.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:05.0: PME# disabled
pci 0000:00:06.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:06.0: PME# disabled
pci 0000:00:07.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:07.0: PME# disabled
pci 0000:00:0a.1: reg 20 io port: [0x5000-0x503f]
pci 0000:00:0a.1: reg 24 io port: [0x5100-0x513f]
pci 0000:00:0a.1: PME# supported from D3hot D3cold
pci 0000:00:0a.1: PME# disabled
pci 0000:00:0b.0: reg 10 32bit mmio: [0xd5006000-0xd5006fff]
pci 0000:00:0b.0: supports D1 D2
pci 0000:00:0b.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:0b.0: PME# disabled
pci 0000:00:0b.1: reg 10 32bit mmio: [0xd5007000-0xd50070ff]
pci 0000:00:0b.1: supports D1 D2
pci 0000:00:0b.1: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:0b.1: PME# disabled
pci 0000:00:0d.0: reg 20 io port: [0xf000-0xf00f]
pci 0000:00:0e.0: reg 10 io port: [0x9f0-0x9f7]
pci 0000:00:0e.0: reg 14 io port: [0xbf0-0xbf3]
pci 0000:00:0e.0: reg 18 io port: [0x970-0x977]
pci 0000:00:0e.0: reg 1c io port: [0xb70-0xb73]
pci 0000:00:0e.0: reg 20 io port: [0xd400-0xd40f]
pci 0000:00:0e.0: reg 24 32bit mmio: [0xd5004000-0xd5004fff]
pci 0000:00:0f.0: reg 10 io port: [0x9e0-0x9e7]
pci 0000:00:0f.0: reg 14 io port: [0xbe0-0xbe3]
pci 0000:00:0f.0: reg 18 io port: [0x960-0x967]
pci 0000:00:0f.0: reg 1c io port: [0xb60-0xb63]
pci 0000:00:0f.0: reg 20 io port: [0xe800-0xe80f]
pci 0000:00:0f.0: reg 24 32bit mmio: [0xd5005000-0xd5005fff]
pci 0000:00:10.1: reg 10 32bit mmio: [0xd5000000-0xd5003fff]
pci 0000:00:10.1: PME# supported from D3hot D3cold
pci 0000:00:10.1: PME# disabled
pci 0000:01:00.0: reg 10 32bit mmio: [0xd0000000-0xd0ffffff]
pci 0000:01:00.0: reg 14 64bit mmio pref: [0xc0000000-0xcfffffff]
pci 0000:01:00.0: reg 1c 64bit mmio: [0xd1000000-0xd1ffffff]
pci 0000:01:00.0: reg 24 io port: [0xa000-0xa07f]
pci 0000:01:00.0: reg 30 32bit mmio pref: [0xd2000000-0xd201ffff]
pci 0000:00:02.0: bridge io port: [0xa000-0xafff]
pci 0000:00:02.0: bridge 32bit mmio: [0xd0000000-0xd2ffffff]
pci 0000:00:02.0: bridge 64bit mmio pref: [0xc0000000-0xcfffffff]
pci 0000:06:06.0: reg 10 32bit mmio: [0xd4001000-0xd40017ff]
pci 0000:06:06.0: reg 14 io port: [0xb000-0xb07f]
pci 0000:06:06.0: supports D2
pci 0000:06:06.0: PME# supported from D2 D3hot D3cold
pci 0000:06:06.0: PME# disabled
pci 0000:06:07.0: reg 10 io port: [0xb400-0xb4ff]
pci 0000:06:07.0: reg 14 32bit mmio: [0xd4000000-0xd40000ff]
pci 0000:06:07.0: reg 30 32bit mmio pref: [0xd3000000-0xd301ffff]
pci 0000:06:07.0: supports D1 D2
pci 0000:06:07.0: PME# supported from D1 D2 D3hot D3cold
pci 0000:06:07.0: PME# disabled
pci 0000:00:10.0: transparent bridge
pci 0000:00:10.0: bridge io port: [0xb000-0xbfff]
pci 0000:00:10.0: bridge 32bit mmio: [0xd3000000-0xd4ffffff]
pci_bus 0000:00: on NUMA node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
PM: Adding info for pci:0000:00:00.0
PM: Adding info for pci:0000:00:00.1
PM: Adding info for pci:0000:00:00.2
PM: Adding info for pci:0000:00:00.3
PM: Adding info for pci:0000:00:00.4
PM: Adding info for pci:0000:00:01.0
PM: Adding info for pci:0000:00:01.1
PM: Adding info for pci:0000:00:01.2
PM: Adding info for pci:0000:00:01.3
PM: Adding info for pci:0000:00:01.4
PM: Adding info for pci:0000:00:01.5
PM: Adding info for pci:0000:00:01.6
PM: Adding info for pci:0000:00:02.0
PM: Adding info for pci:0000:00:04.0
PM: Adding info for pci:0000:00:05.0
PM: Adding info for pci:0000:00:06.0
PM: Adding info for pci:0000:00:07.0
PM: Adding info for pci:0000:00:09.0
PM: Adding info for pci:0000:00:0a.0
PM: Adding info for pci:0000:00:0a.1
PM: Adding info for pci:0000:00:0a.2
PM: Adding info for pci:0000:00:0b.0
PM: Adding info for pci:0000:00:0b.1
PM: Adding info for pci:0000:00:0d.0
PM: Adding info for pci:0000:00:0e.0
PM: Adding info for pci:0000:00:0f.0
PM: Adding info for pci:0000:00:10.0
PM: Adding info for pci:0000:00:10.1
PM: Adding info for pci:0000:01:00.0
PM: Adding info for No Bus:0000:01
PM: Adding info for No Bus:0000:02
PM: Adding info for No Bus:0000:03
PM: Adding info for No Bus:0000:04
PM: Adding info for No Bus:0000:05
PM: Adding info for pci:0000:06:06.0
PM: Adding info for pci:0000:06:07.0
PM: Adding info for No Bus:0000:06
ACPI: PCI Interrupt Link [LNK1] (IRQs 5 7 9 *10 11 14 15)
ACPI: PCI Interrupt Link [LNK2] (IRQs *5 7 9 10 11 14 15)
ACPI: PCI Interrupt Link [LNK3] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK4] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK5] (IRQs 5 *7 9 10 11 14 15)
ACPI: PCI Interrupt Link [LNK6] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK7] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK8] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LUBA] (IRQs 5 *7 9 10 11 14 15)
ACPI: PCI Interrupt Link [LUBB] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LMAC] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LACI] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LAZA] (IRQs 5 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [LPMU] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LMCI] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSMB] (IRQs 5 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [LUB2] (IRQs *5 7 9 10 11 14 15)
ACPI: PCI Interrupt Link [LIDE] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSID] (IRQs 5 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [LFID] (IRQs 5 7 9 *10 11 14 15)
ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0
ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0
ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0, disabled.
ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled.
ACPI: PCI Interrupt Link [APC5] (IRQs 16) *0
ACPI: PCI Interrupt Link [APC6] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APC7] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APC8] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APMU] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [AAZA] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0
PM: Adding info for No Bus:vga_arbiter
vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
vgaarb: loaded
PCI: Using ACPI for IRQ routing
PM: Adding info for No Bus:lo
hpet0: at MMIO 0xfeff0000, IRQs 2, 8, 31
hpet0: 3 comparators, 32-bit 25.000000 MHz counter
Switching to clocksource tsc
pnp: PnP ACPI init
PM: Adding info for No Bus:pnp0
ACPI: bus type pnp registered
PM: Adding info for pnp:00:00
PM: Adding info for pnp:00:01
PM: Adding info for pnp:00:02
PM: Adding info for pnp:00:03
PM: Adding info for pnp:00:04
PM: Adding info for pnp:00:05
PM: Adding info for pnp:00:06
PM: Adding info for pnp:00:07
PM: Adding info for pnp:00:08
PM: Adding info for pnp:00:09
pnp: PnP ACPI: found 10 devices
ACPI: ACPI bus type pnp unregistered
PnPBIOS: Disabled by ACPI PNP
system 00:01: ioport range 0x4000-0x407f has been reserved
system 00:01: ioport range 0x4080-0x40ff has been reserved
system 00:01: ioport range 0x4400-0x447f has been reserved
system 00:01: ioport range 0x4480-0x44ff has been reserved
system 00:01: ioport range 0x4800-0x487f has been reserved
system 00:01: ioport range 0x4880-0x48ff has been reserved
system 00:02: ioport range 0x4d0-0x4d1 has been reserved
system 00:02: ioport range 0x800-0x87f has been reserved
system 00:02: ioport range 0x290-0x297 has been reserved
system 00:02: ioport range 0x880-0x88f has been reserved
system 00:08: iomem range 0xe0000000-0xefffffff has been reserved
system 00:09: iomem range 0xdbc00-0xdbfff has been reserved
system 00:09: iomem range 0xf0000-0xf7fff could not be reserved
system 00:09: iomem range 0xf8000-0xfbfff could not be reserved
system 00:09: iomem range 0xfc000-0xfffff could not be reserved
system 00:09: iomem range 0xfeff0000-0xfeff00ff has been reserved
system 00:09: iomem range 0x7fef0000-0x7fefffff could not be reserved
system 00:09: iomem range 0xffff0000-0xffffffff has been reserved
system 00:09: iomem range 0x0-0x9ffff could not be reserved
system 00:09: iomem range 0x100000-0x7feeffff could not be reserved
system 00:09: iomem range 0xfec00000-0xfec00fff could not be reserved
system 00:09: iomem range 0xfee00000-0xfee00fff has been reserved
system 00:09: iomem range 0xfeff0000-0xfeff03ff could not be reserved
PM: Adding info for No Bus:mem
PM: Adding info for No Bus:kmem
PM: Adding info for No Bus:null
PM: Adding info for No Bus:port
PM: Adding info for No Bus:zero
PM: Adding info for No Bus:full
PM: Adding info for No Bus:random
PM: Adding info for No Bus:urandom
PM: Adding info for No Bus:kmsg
pci 0000:06:07.0: BAR 6: address space collision on of device [0xd3000000-0xd301ffff]
pci 0000:00:02.0: PCI bridge, secondary bus 0000:01
pci 0000:00:02.0: IO window: 0xa000-0xafff
pci 0000:00:02.0: MEM window: 0xd0000000-0xd2ffffff
pci 0000:00:02.0: PREFETCH window: 0x000000c0000000-0x000000cfffffff
pci 0000:00:04.0: PCI bridge, secondary bus 0000:02
pci 0000:00:04.0: IO window: disabled
pci 0000:00:04.0: MEM window: disabled
pci 0000:00:04.0: PREFETCH window: disabled
pci 0000:00:05.0: PCI bridge, secondary bus 0000:03
pci 0000:00:05.0: IO window: disabled
pci 0000:00:05.0: MEM window: disabled
pci 0000:00:05.0: PREFETCH window: disabled
pci 0000:00:06.0: PCI bridge, secondary bus 0000:04
pci 0000:00:06.0: IO window: disabled
pci 0000:00:06.0: MEM window: disabled
pci 0000:00:06.0: PREFETCH window: disabled
pci 0000:00:07.0: PCI bridge, secondary bus 0000:05
pci 0000:00:07.0: IO window: disabled
pci 0000:00:07.0: MEM window: disabled
pci 0000:00:07.0: PREFETCH window: disabled
pci 0000:00:10.0: PCI bridge, secondary bus 0000:06
pci 0000:00:10.0: IO window: 0xb000-0xbfff
pci 0000:00:10.0: MEM window: 0xd3000000-0xd4ffffff
pci 0000:00:10.0: PREFETCH window: 0x80000000-0x800fffff
pci 0000:00:02.0: setting latency timer to 64
pci 0000:00:04.0: setting latency timer to 64
pci 0000:00:05.0: setting latency timer to 64
pci 0000:00:06.0: setting latency timer to 64
pci 0000:00:07.0: setting latency timer to 64
pci 0000:00:10.0: setting latency timer to 64
pci_bus 0000:00: resource 0 io: [0x00-0xffff]
pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
pci_bus 0000:01: resource 0 io: [0xa000-0xafff]
pci_bus 0000:01: resource 1 mem: [0xd0000000-0xd2ffffff]
pci_bus 0000:01: resource 2 pref mem [0xc0000000-0xcfffffff]
pci_bus 0000:06: resource 0 io: [0xb000-0xbfff]
pci_bus 0000:06: resource 1 mem: [0xd3000000-0xd4ffffff]
pci_bus 0000:06: resource 2 pref mem [0x80000000-0x800fffff]
pci_bus 0000:06: resource 3 io: [0x00-0xffff]
pci_bus 0000:06: resource 4 mem: [0x000000-0xffffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
pci 0000:01:00.0: Boot video device
Trying to unpack rootfs image as initramfs...
Freeing initrd memory: 20744k freed
PM: Adding info for No Bus:mcelog
PM: Adding info for No Bus:msr0
PM: Adding info for No Bus:msr1
PM: Adding info for platform:pcspkr
PM: Adding info for No Bus:snapshot
highmem bounce pool size: 64 pages
ROMFS MTD (C) 2007 Red Hat, Inc.
msgmni has been set to 1733
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
pcieport 0000:00:02.0: setting latency timer to 64
PM: Adding info for pci_express:0000:00:02.0:pcie08
pcieport 0000:00:04.0: setting latency timer to 64
PM: Adding info for pci_express:0000:00:04.0:pcie08
pcieport 0000:00:05.0: setting latency timer to 64
PM: Adding info for pci_express:0000:00:05.0:pcie08
pcieport 0000:00:06.0: setting latency timer to 64
PM: Adding info for pci_express:0000:00:06.0:pcie08
pcieport 0000:00:07.0: setting latency timer to 64
PM: Adding info for pci_express:0000:00:07.0:pcie08
PM: Adding info for No Bus:pnp1
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
PM: Adding info for No Bus:tty
PM: Adding info for No Bus:console
PM: Adding info for No Bus:tty0
PM: Adding info for No Bus:vcs
PM: Adding info for No Bus:vcsa
PM: Adding info for No Bus:vcs1
PM: Adding info for No Bus:vcsa1
PM: Adding info for No Bus:tty1
PM: Adding info for No Bus:tty2
PM: Adding info for No Bus:tty3
PM: Adding info for No Bus:tty4
PM: Adding info for No Bus:tty5
PM: Adding info for No Bus:tty6
PM: Adding info for No Bus:tty7
PM: Adding info for No Bus:tty8
PM: Adding info for No Bus:tty9
PM: Adding info for No Bus:tty10
PM: Adding info for No Bus:tty11
PM: Adding info for No Bus:tty12
PM: Adding info for No Bus:tty13
PM: Adding info for No Bus:tty14
PM: Adding info for No Bus:tty15
PM: Adding info for No Bus:tty16
PM: Adding info for No Bus:tty17
PM: Adding info for No Bus:tty18
PM: Adding info for No Bus:tty19
PM: Adding info for No Bus:tty20
PM: Adding info for No Bus:tty21
PM: Adding info for No Bus:tty22
PM: Adding info for No Bus:tty23
PM: Adding info for No Bus:tty24
PM: Adding info for No Bus:tty25
PM: Adding info for No Bus:tty26
PM: Adding info for No Bus:tty27
PM: Adding info for No Bus:tty28
PM: Adding info for No Bus:tty29
PM: Adding info for No Bus:tty30
PM: Adding info for No Bus:tty31
PM: Adding info for No Bus:tty32
PM: Adding info for No Bus:tty33
PM: Adding info for No Bus:tty34
PM: Adding info for No Bus:tty35
PM: Adding info for No Bus:tty36
PM: Adding info for No Bus:tty37
PM: Adding info for No Bus:tty38
PM: Adding info for No Bus:tty39
PM: Adding info for No Bus:tty40
PM: Adding info for No Bus:tty41
PM: Adding info for No Bus:tty42
PM: Adding info for No Bus:tty43
PM: Adding info for No Bus:tty44
PM: Adding info for No Bus:tty45
PM: Adding info for No Bus:tty46
PM: Adding info for No Bus:tty47
PM: Adding info for No Bus:tty48
PM: Adding info for No Bus:tty49
PM: Adding info for No Bus:tty50
PM: Adding info for No Bus:tty51
PM: Adding info for No Bus:tty52
PM: Adding info for No Bus:tty53
PM: Adding info for No Bus:tty54
PM: Adding info for No Bus:tty55
PM: Adding info for No Bus:tty56
PM: Adding info for No Bus:tty57
PM: Adding info for No Bus:tty58
PM: Adding info for No Bus:tty59
PM: Adding info for No Bus:tty60
PM: Adding info for No Bus:tty61
PM: Adding info for No Bus:tty62
PM: Adding info for No Bus:tty63
PM: Adding info for No Bus:ptmx
PM: Adding info for No Bus:hpet
PM: Adding info for No Bus:isa
PM: Adding info for No Bus:ram0
PM: Adding info for No Bus:1:0
PM: Adding info for No Bus:ram1
PM: Adding info for No Bus:1:1
PM: Adding info for No Bus:ram2
PM: Adding info for No Bus:1:2
PM: Adding info for No Bus:ram3
PM: Adding info for No Bus:1:3
PM: Adding info for No Bus:ram4
PM: Adding info for No Bus:1:4
PM: Adding info for No Bus:ram5
PM: Adding info for No Bus:1:5
PM: Adding info for No Bus:ram6
PM: Adding info for No Bus:1:6
PM: Adding info for No Bus:ram7
PM: Adding info for No Bus:1:7
PM: Adding info for No Bus:ram8
PM: Adding info for No Bus:1:8
PM: Adding info for No Bus:ram9
PM: Adding info for No Bus:1:9
PM: Adding info for No Bus:ram10
PM: Adding info for No Bus:1:10
PM: Adding info for No Bus:ram11
PM: Adding info for No Bus:1:11
PM: Adding info for No Bus:ram12
PM: Adding info for No Bus:1:12
PM: Adding info for No Bus:ram13
PM: Adding info for No Bus:1:13
PM: Adding info for No Bus:ram14
PM: Adding info for No Bus:1:14
PM: Adding info for No Bus:ram15
PM: Adding info for No Bus:1:15
brd: module loaded
PNP: No PS/2 controller found. Probing ports directly.
PM: Adding info for platform:i8042
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
PM: Adding info for serio:serio0
PM: Adding info for serio:serio1
PM: Adding info for No Bus:mice
PM: Adding info for No Bus:psaux
mice: PS/2 mouse device common for all mice
PM: Adding info for platform:eisa.0
EISA: Probing bus 0 at eisa.0
PM: Removing info for platform:eisa.0
cpuidle: using governor ladder
TCP cubic registered
Using IPI No-Shortcut mode
PM: Adding info for No Bus:cpu_dma_latency
PM: Adding info for No Bus:network_latency
PM: Adding info for No Bus:network_throughput
PM: Checking image partition /dev/hda6
PM: Resume from disk failed.
Magic number: 14:377:682
Freeing unused kernel memory: 404k freed
NET: Registered protocol family 1
PM: Adding info for No Bus:cooling_device0
fan PNP0C0B:00: registered as cooling_device0
ACPI: Fan [FAN] (on)
PM: Adding info for No Bus:thermal_zone0
thermal LNXTHERM:01: registered as thermal_zone0
ACPI: Thermal Zone [THRM] (40 C)
Uniform Multi-Platform E-IDE driver
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16
ohci1394 0000:06:06.0: PCI INT A -> Link[APC1] -> GSI 16 (level, low) -> IRQ 16
PM: Adding info for ieee1394:fw-host0
PM: Adding info for No Bus:fw-host0
libata version 3.00 loaded.
amd74xx 0000:00:0d.0: UDMA133 controller
amd74xx 0000:00:0d.0: IDE controller (0x10de:0x0265 rev 0xa1)
amd74xx 0000:00:0d.0: IDE port disabled
amd74xx 0000:00:0d.0: BIOS didn't set cable bits correctly. Enabling workaround.
amd74xx 0000:00:0d.0: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xf008-0xf00f
Probing IDE interface ide0...
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_hcd: block sizes: qh 60 qtd 96 itd 160 sitd 96
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci_hcd: block sizes: ed 64 td 64
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[16] MMIO=[d4001000-d40017ff] Max Packet=[2] IR/IT contexts=[4/8]
ohci1394: fw-host0: Serial EEPROM has suspicious values, attempting to set max_packet_size to 512 bytes
r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17
r8169 0000:06:07.0: PCI INT A -> Link[APC2] -> GSI 17 (level, low) -> IRQ 17
r8169 0000:06:07.0: no PCI Express capability
PM: Adding info for No Bus:eth0
eth0: RTL8169sb/8110sb at 0xf8d40000, 00:14:d1:1a:ac:15, XID 10000000 IRQ 17
udev: renamed network interface eth0 to eth1
hda: PIONEER DVD-RW DVR-111D, ATAPI CD/DVD-ROM drive
PM: Adding info for No Bus:ide0
PM: Adding info for No Bus:ide0
hda: host max PIO5 wanted PIO255(auto-tune) selected PIO4
hda: UDMA/66 mode selected
ide0 at 0x170-0x177,0x376 on irq 15
PM: Adding info for ide:0.0
sata_nv 0000:00:0e.0: version 3.5
ACPI: PCI Interrupt Link [APSI] enabled at IRQ 23
sata_nv 0000:00:0e.0: PCI INT A -> Link[APSI] -> GSI 23 (level, low) -> IRQ 23
sata_nv 0000:00:0e.0: Using SWNCQ mode
sata_nv 0000:00:0e.0: setting latency timer to 64
scsi0 : sata_nv
PM: Adding info for scsi:host0
PM: Adding info for No Bus:host0
scsi1 : sata_nv
PM: Adding info for scsi:host1
PM: Adding info for No Bus:host1
ata1: SATA max UDMA/133 cmd 0x9f0 ctl 0xbf0 bmdma 0xd400 irq 23
ata2: SATA max UDMA/133 cmd 0x970 ctl 0xb70 bmdma 0xd408 irq 23
ACPI: PCI Interrupt Link [APCL] enabled at IRQ 22
ehci_hcd 0000:00:0b.1: PCI INT B -> Link[APCL] -> GSI 22 (level, low) -> IRQ 22
ehci_hcd 0000:00:0b.1: setting latency timer to 64
ehci_hcd 0000:00:0b.1: EHCI Host Controller
drivers/usb/core/inode.c: creating file 'devices'
drivers/usb/core/inode.c: creating file '001'
ehci_hcd 0000:00:0b.1: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:0b.1: reset hcs_params 0x101888 dbg=1 cc=1 pcc=8 !ppc ports=8
ehci_hcd 0000:00:0b.1: reset portroute 0 0 0 0 0 0 0 0
ehci_hcd 0000:00:0b.1: reset hcc_params a086 caching frame 256/512/1024 park
ehci_hcd 0000:00:0b.1: park 0
ehci_hcd 0000:00:0b.1: debug port 1
ehci_hcd 0000:00:0b.1: reset command 080b02 park=3 ithresh=8 period=1024 Reset HALT
ehci_hcd 0000:00:0b.1: cache line size of 32 is not supported
ehci_hcd 0000:00:0b.1: supports USB remote wakeup
ehci_hcd 0000:00:0b.1: irq 22, io mem 0xd5007000
ehci_hcd 0000:00:0b.1: reset command 080b02 park=3 ithresh=8 period=1024 Reset HALT
ehci_hcd 0000:00:0b.1: init command 010009 (park)=0 ithresh=1 period=256 RUN
ehci_hcd 0000:00:0b.1: USB 2.0 started, EHCI 1.00
usb usb1: default language 0x0409
usb usb1: udev 1, busnum 1, minor = 0
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.32testing ehci_hcd
usb usb1: SerialNumber: 0000:00:0b.1
PM: Adding info for usb:usb1
usb usb1: uevent
usb usb1: usb_probe_device
usb usb1: configuration #1 chosen from 1 choice
usb usb1: adding 1-0:1.0 (config #1, interface 0)
PM: Adding info for usb:1-0:1.0
usb 1-0:1.0: uevent
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: no power switching (usb 1.0)
hub 1-0:1.0: individual port over-current protection
hub 1-0:1.0: power on to power good time: 20ms
hub 1-0:1.0: local power source is good
hub 1-0:1.0: trying to enable port power on non-switchable hub
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev1.1
drivers/usb/core/inode.c: creating file '001'
PM: Adding info for No Bus:ep_00
ACPI: PCI Interrupt Link [APCF] enabled at IRQ 21
ohci_hcd 0000:00:0b.0: PCI INT A -> Link[APCF] -> GSI 21 (level, low) -> IRQ 21
ohci_hcd 0000:00:0b.0: setting latency timer to 64
ohci_hcd 0000:00:0b.0: OHCI Host Controller
drivers/usb/core/inode.c: creating file '002'
ohci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:0b.0: created debug files
ohci_hcd 0000:00:0b.0: supports USB remote wakeup
ohci_hcd 0000:00:0b.0: irq 21, io mem 0xd5006000
PM: Adding info for ieee1394:001106000000bd66
PM: Adding info for No Bus:001106000000bd66
ieee1394: Host added: ID:BUS[0-00:1023] GUID[001106000000bd66]
PM: Adding info for ieee1394:001a66fffee31809
PM: Adding info for No Bus:001a66fffee31809
ieee1394: Node added: ID:BUS[0-01:1023] GUID[001a66fffee31809]
PM: Adding info for ieee1394:001a66fffee31809-0
PM: Adding info for No Bus:001a66fffee31809-0
PM: Adding info for ieee1394:001a66fffee31809-1
PM: Adding info for No Bus:001a66fffee31809-1
ohci_hcd 0000:00:0b.0: OHCI controller state
ohci_hcd 0000:00:0b.0: OHCI 1.0, NO legacy support registers
ohci_hcd 0000:00:0b.0: control 0x683 RWE RWC HCFS=operational CBSR=3
ohci_hcd 0000:00:0b.0: cmdstatus 0x00000 SOC=0
ohci_hcd 0000:00:0b.0: intrstatus 0x00000004 SF
ohci_hcd 0000:00:0b.0: intrenable 0x8000004a MIE RHSC RD WDH
ohci_hcd 0000:00:0b.0: hcca frame #0003
ohci_hcd 0000:00:0b.0: roothub.a 01000208 POTPGT=1 NPS NDP=8(8)
ohci_hcd 0000:00:0b.0: roothub.b 00000000 PPCM=0000 DR=0000
ohci_hcd 0000:00:0b.0: roothub.status 00008000 DRWE
ohci_hcd 0000:00:0b.0: roothub.portstatus [0] 0x00000100 PPS
ohci_hcd 0000:00:0b.0: roothub.portstatus [1] 0x00000100 PPS
ohci_hcd 0000:00:0b.0: roothub.portstatus [2] 0x00000100 PPS
ohci_hcd 0000:00:0b.0: roothub.portstatus [3] 0x00000100 PPS
ohci_hcd 0000:00:0b.0: roothub.portstatus [4] 0x00000100 PPS
ohci_hcd 0000:00:0b.0: roothub.portstatus [5] 0x00000100 PPS
ohci_hcd 0000:00:0b.0: roothub.portstatus [6] 0x00000100 PPS
ohci_hcd 0000:00:0b.0: roothub.portstatus [7] 0x00000100 PPS
usb usb2: default language 0x0409
usb usb2: udev 1, busnum 2, minor = 128
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: OHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.32testing ohci_hcd
usb usb2: SerialNumber: 0000:00:0b.0
PM: Adding info for usb:usb2
usb usb2: uevent
usb usb2: usb_probe_device
usb usb2: configuration #1 chosen from 1 choice
usb usb2: adding 2-0:1.0 (config #1, interface 0)
PM: Adding info for usb:2-0:1.0
usb 2-0:1.0: uevent
hub 2-0:1.0: usb_probe_interface
hub 2-0:1.0: usb_probe_interface - got id
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 8 ports detected
hub 2-0:1.0: standalone hub
hub 2-0:1.0: no power switching (usb 1.0)
hub 2-0:1.0: global over-current protection
hub 2-0:1.0: power on to power good time: 2ms
hub 2-0:1.0: local power source is good
hub 2-0:1.0: no over-current condition exists
hub 2-0:1.0: trying to enable port power on non-switchable hub
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev2.1
drivers/usb/core/inode.c: creating file '001'
PM: Adding info for No Bus:ep_00
ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 20
sata_nv 0000:00:0f.0: PCI INT A -> Link[APSJ] -> GSI 20 (level, low) -> IRQ 20
sata_nv 0000:00:0f.0: Using SWNCQ mode
sata_nv 0000:00:0f.0: setting latency timer to 64
scsi2 : sata_nv
PM: Adding info for scsi:host2
PM: Adding info for No Bus:host2
scsi3 : sata_nv
PM: Adding info for scsi:host3
PM: Adding info for No Bus:host3
ata3: SATA max UDMA/133 cmd 0x9e0 ctl 0xbe0 bmdma 0xe800 irq 20
ata4: SATA max UDMA/133 cmd 0x960 ctl 0xb60 bmdma 0xe808 irq 20
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 1-0:1.0: port 1: status 0501 change 0001
ehci_hcd 0000:00:0b.1: GetStatus port 2 status 001803 POWER sig=j CSC CONNECT
hub 1-0:1.0: port 2: status 0501 change 0001
ehci_hcd 0000:00:0b.1: GetStatus port 3 status 001803 POWER sig=j CSC CONNECT
hub 1-0:1.0: port 3: status 0501 change 0001
ehci_hcd 0000:00:0b.1: GetStatus port 6 status 001803 POWER sig=j CSC CONNECT
hub 1-0:1.0: port 6: status 0501 change 0001
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0000
hub 1-0:1.0: state 7 ports 8 chg 004e evt 0000
hub 1-0:1.0: port 1, status 0501, change 0000, 480 Mb/s
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 1-0:1.0: port 2, status 0501, change 0000, 480 Mb/s
ehci_hcd 0000:00:0b.1: port 2 high speed
ehci_hcd 0000:00:0b.1: GetStatus port 2 status 001005 POWER sig=se0 PE CONNECT
usb 1-2: new high speed USB device using ehci_hcd and address 3
ata3: SATA link down (SStatus 0 SControl 300)
ehci_hcd 0000:00:0b.1: port 2 high speed
ehci_hcd 0000:00:0b.1: GetStatus port 2 status 001005 POWER sig=se0 PE CONNECT
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: ATA-7: SAMSUNG SP2504C, VT100-41, max UDMA7
ata1.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32)
usb 1-2: default language 0x0409
usb 1-2: udev 3, busnum 1, minor = 2
usb 1-2: New USB device found, idVendor=058f, idProduct=6362
usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-2: Product: Mass Storage Device
usb 1-2: Manufacturer: Generic
usb 1-2: SerialNumber: 058F312D81B
PM: Adding info for usb:1-2
usb 1-2: uevent
usb 1-2: usb_probe_device
usb 1-2: configuration #1 chosen from 1 choice
usb 1-2: adding 1-2:1.0 (config #1, interface 0)
PM: Adding info for usb:1-2:1.0
usb 1-2:1.0: uevent
PM: Adding info for No Bus:ep_01
PM: Adding info for No Bus:ep_82
PM: Adding info for No Bus:usbdev1.3
drivers/usb/core/inode.c: creating file '003'
PM: Adding info for No Bus:ep_00
hub 1-0:1.0: port 3, status 0501, change 0000, 480 Mb/s
ata1.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access ATA SAMSUNG SP2504C VT10 PQ: 0 ANSI: 5
PM: Adding info for scsi:target0:0:0
PM: Adding info for scsi:0:0:0:0
PM: Adding info for No Bus:0:0:0:0
PM: Adding info for No Bus:0:0:0:0
ehci_hcd 0000:00:0b.1: port 3 high speed
ehci_hcd 0000:00:0b.1: GetStatus port 3 status 001005 POWER sig=se0 PE CONNECT
usb 1-3: new high speed USB device using ehci_hcd and address 4
ehci_hcd 0000:00:0b.1: port 3 high speed
ehci_hcd 0000:00:0b.1: GetStatus port 3 status 001005 POWER sig=se0 PE CONNECT
usb 1-3: default language 0x0409
usb 1-3: udev 4, busnum 1, minor = 3
usb 1-3: New USB device found, idVendor=05e3, idProduct=0605
usb 1-3: New USB device strings: Mfr=0, Product=1, SerialNumber=0
usb 1-3: Product: USB2.0 Hub
PM: Adding info for usb:1-3
usb 1-3: uevent
usb 1-3: usb_probe_device
usb 1-3: configuration #1 chosen from 1 choice
usb 1-3: adding 1-3:1.0 (config #1, interface 0)
PM: Adding info for usb:1-3:1.0
usb 1-3:1.0: uevent
hub 1-3:1.0: usb_probe_interface
hub 1-3:1.0: usb_probe_interface - got id
hub 1-3:1.0: USB hub found
hub 1-3:1.0: 4 ports detected
hub 1-3:1.0: standalone hub
hub 1-3:1.0: individual port power switching
hub 1-3:1.0: individual port over-current protection
hub 1-3:1.0: Single TT
hub 1-3:1.0: TT requires at most 32 FS bit times (2664 ns)
hub 1-3:1.0: Port indicators are supported
hub 1-3:1.0: power on to power good time: 100ms
hub 1-3:1.0: local power source is good
hub 1-3:1.0: enabling power on all ports
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev1.4
drivers/usb/core/inode.c: creating file '004'
PM: Adding info for No Bus:ep_00
hub 1-0:1.0: port 6, status 0501, change 0000, 480 Mb/s
ehci_hcd 0000:00:0b.1: port 6 high speed
ehci_hcd 0000:00:0b.1: GetStatus port 6 status 001005 POWER sig=se0 PE CONNECT
hub 1-3:1.0: port 1: status 0101 change 0001
usb 1-6: new high speed USB device using ehci_hcd and address 5
ehci_hcd 0000:00:0b.1: port 6 high speed
ehci_hcd 0000:00:0b.1: GetStatus port 6 status 001005 POWER sig=se0 PE CONNECT
usb 1-3: link qh256-0001/c2372500 start 1 [1/0 us]
usb 1-6: udev 5, busnum 1, minor = 4
usb 1-6: New USB device found, idVendor=0409, idProduct=0059
usb 1-6: New USB device strings: Mfr=0, Product=0, SerialNumber=0
PM: Adding info for usb:1-6
usb 1-6: uevent
usb 1-6: usb_probe_device
usb 1-6: configuration #1 chosen from 1 choice
usb 1-6: adding 1-6:1.0 (config #1, interface 0)
PM: Adding info for usb:1-6:1.0
usb 1-6:1.0: uevent
hub 1-6:1.0: usb_probe_interface
hub 1-6:1.0: usb_probe_interface - got id
hub 1-6:1.0: USB hub found
hub 1-6:1.0: 4 ports detected
hub 1-6:1.0: standalone hub
hub 1-6:1.0: individual port power switching
hub 1-6:1.0: individual port over-current protection
hub 1-6:1.0: Single TT
hub 1-6:1.0: TT requires at most 16 FS bit times (1332 ns)
hub 1-6:1.0: Port indicators are supported
hub 1-6:1.0: power on to power good time: 100ms
hub 1-6:1.0: local power source is good
hub 1-6:1.0: enabling power on all ports
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev1.5
drivers/usb/core/inode.c: creating file '005'
PM: Adding info for No Bus:ep_00
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00010301 CSC LSDA PPS CCS
hub 2-0:1.0: port 1, status 0301, change 0001, 1.5 Mb/s
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2.00: ATA-7: ST3250620AS, 3.AAC, max UDMA/133
ata2.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32)
hub 1-6:1.0: port 1: status 0301 change 0001
hub 1-6:1.0: port 3: status 0101 change 0001
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ata2.00: configured for UDMA/133
scsi 1:0:0:0: Direct-Access ATA ST3250620AS 3.AA PQ: 0 ANSI: 5
PM: Adding info for scsi:target1:0:0
PM: Adding info for scsi:1:0:0:0
PM: Adding info for No Bus:1:0:0:0
PM: Adding info for No Bus:1:0:0:0
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130301 PRSC PESC CSC LSDA PPS CCS
hub 2-0:1.0: unable to enumerate USB device on port 1
hub 1-3:1.0: state 7 ports 4 chg 0002 evt 0000
hub 1-3:1.0: port 1, status 0101, change 0000, 12 Mb/s
usb 1-6: link qh256-0001/c2372700 start 2 [1/0 us]
usb 1-3.1: new high speed USB device using ehci_hcd and address 6
hub 1-3:1.0: port 1 not reset yet, waiting 10ms
usb 1-3.1: udev 6, busnum 1, minor = 5
usb 1-3.1: New USB device found, idVendor=0409, idProduct=0059
usb 1-3.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
PM: Adding info for usb:1-3.1
usb 1-3.1: uevent
usb 1-3.1: usb_probe_device
usb 1-3.1: configuration #1 chosen from 1 choice
usb 1-3.1: adding 1-3.1:1.0 (config #1, interface 0)
PM: Adding info for usb:1-3.1:1.0
usb 1-3.1:1.0: uevent
hub 1-3.1:1.0: usb_probe_interface
hub 1-3.1:1.0: usb_probe_interface - got id
hub 1-3.1:1.0: USB hub found
hub 1-3.1:1.0: 4 ports detected
hub 1-3.1:1.0: standalone hub
hub 1-3.1:1.0: individual port power switching
hub 1-3.1:1.0: individual port over-current protection
hub 1-3.1:1.0: Single TT
hub 1-3.1:1.0: TT requires at most 16 FS bit times (1332 ns)
hub 1-3.1:1.0: Port indicators are supported
hub 1-3.1:1.0: power on to power good time: 100ms
hub 1-3.1:1.0: local power source is good
hub 1-3.1:1.0: enabling power on all ports
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev1.6
drivers/usb/core/inode.c: creating file '006'
PM: Adding info for No Bus:ep_00
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 2-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 1-3.1:1.0: port 1: status 0301 change 0001
hub 1-3.1:1.0: port 2: status 0101 change 0001
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130301 PRSC PESC CSC LSDA PPS CCS
hub 2-0:1.0: unable to enumerate USB device on port 1
hub 1-6:1.0: state 7 ports 4 chg 000a evt 0000
hub 1-6:1.0: port 1, status 0301, change 0000, 1.5 Mb/s
hub 1-6:1.0: port 1 not reset yet, waiting 10ms
usb 1-3.1: link qh256-0001/c2372840 start 3 [1/0 us]
usb 1-6.1: new low speed USB device using ehci_hcd and address 7
hub 1-6:1.0: port 1 not reset yet, waiting 10ms
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: ATAPI: ATAPI iHOS104, WL08, max UDMA/100
ata4.00: configured for UDMA/100
scsi 3:0:0:0: CD-ROM ATAPI iHOS104 WL08 PQ: 0 ANSI: 5
PM: Adding info for scsi:target3:0:0
PM: Adding info for scsi:3:0:0:0
PM: Adding info for No Bus:3:0:0:0
PM: Adding info for No Bus:3:0:0:0
usb usb2: uevent
usb usb2: uevent
usb usb1: uevent
usb usb1: uevent
usb 1-3: uevent
usb 1-3: uevent
usb 1-6: uevent
PM: Adding info for No Bus:0:0:0:0
sd 0:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
PM: Adding info for No Bus:sda
sda:
PM: Adding info for No Bus:1:0:0:0
sd 1:0:0:0: [sdb] 488397168 512-byte logical blocks: (250 GB/232 GiB)
sd 1:0:0:0: [sdb] Write Protect is off
usb 1-6: uevent
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
PM: Adding info for No Bus:sdb
sdb:
usb 1-3.1: uevent
ide-cd driver 5.00
PM: Adding info for No Bus:0.0
usb 1-3.1: uevent
ide-cd: hda: ATAPI 94X DVD-ROM DVD-R CD-R/RW drive, 2000kB Cache
Uniform CD-ROM driver Revision: 3.20
usb 1-2: uevent
usb 1-2: uevent
usb 1-6.1: skipped 1 descriptor after interface
usb 1-6.1: default language 0x0409
sda1 sda2 sda3 <
usb 1-6.1: udev 7, busnum 1, minor = 6
usb 1-6.1: New USB device found, idVendor=2222, idProduct=3100
usb 1-6.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-6.1: Product: Macally ECOMouse
usb 1-6.1: Manufacturer: Macally Peripherals
PM: Adding info for usb:1-6.1
usb 1-6.1: uevent
usb 1-6.1: usb_probe_device
usb 1-6.1: configuration #1 chosen from 1 choice
usb 1-6.1: adding 1-6.1:1.0 (config #1, interface 0)
PM: Adding info for usb:1-6.1:1.0
usb 1-6.1:1.0: uevent
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev1.7
drivers/usb/core/inode.c: creating file '007'
PM: Adding info for No Bus:ep_00
hub 1-6:1.0: port 3, status 0101, change 0000, 12 Mb/s
usb 1-6.1: uevent
usb 1-6.1: uevent
Initializing USB Mass Storage driver...
usb-storage 1-2:1.0: usb_probe_interface
usb-storage 1-2:1.0: usb_probe_interface - got id
scsi4 : SCSI emulation for USB Mass Storage devices
PM: Adding info for scsi:host4
PM: Adding info for No Bus:host4
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
unknown partition table
PM: Adding info for No Bus:8:16
sd 1:0:0:0: [sdb] Attached SCSI disk
usbcore: registered new interface driver hiddev
usbhid 1-6.1:1.0: usb_probe_interface
usbhid 1-6.1:1.0: usb_probe_interface - got id
PM: Adding info for hid:0003:2222:3100.0001
>
PM: Adding info for No Bus:sda1
PM: Adding info for No Bus:sda2
PM: Adding info for No Bus:sda3
PM: Adding info for No Bus:8:0
hub 1-6:1.0: port 3 not reset yet, waiting 10ms
PM: Adding info for No Bus:input0
input: Macally Peripherals Macally ECOMouse as /devices/pci0000:00/0000:00:0b.1/usb1/1-6/1-6.1/1-6.1:1.0/input/input0
PM: Adding info for No Bus:mouse0
generic-usb 0003:2222:3100.0001: input: USB HID v1.00 Mouse [Macally Peripherals Macally ECOMouse ] on usb-0000:00:0b.1-6.1/input0
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
sd 0:0:0:0: [sda] Attached SCSI disk
PM: Adding info for No Bus:hda
PM: Adding info for No Bus:3:0
usb 1-6.3: new full speed USB device using ehci_hcd and address 8
hub 1-6:1.0: port 3 not reset yet, waiting 10ms
usb 1-6.3: ep0 maxpacket = 8
usb 1-6.3: default language 0x0409
usb 1-6.3: udev 8, busnum 1, minor = 7
usb 1-6.3: New USB device found, idVendor=05e3, idProduct=0604
usb 1-6.3: New USB device strings: Mfr=0, Product=1, SerialNumber=0
usb 1-6.3: Product: USB Hub
PM: Adding info for usb:1-6.3
usb 1-6.3: uevent
usb 1-6.3: usb_probe_device
usb 1-6.3: configuration #1 chosen from 1 choice
usb 1-6.3: adding 1-6.3:1.0 (config #1, interface 0)
PM: Adding info for usb:1-6.3:1.0
usb 1-6.3:1.0: uevent
hub 1-6.3:1.0: usb_probe_interface
hub 1-6.3:1.0: usb_probe_interface - got id
hub 1-6.3:1.0: USB hub found
hub 1-6.3:1.0: 4 ports detected
hub 1-6.3:1.0: standalone hub
hub 1-6.3:1.0: individual port power switching
hub 1-6.3:1.0: individual port over-current protection
hub 1-6.3:1.0: power on to power good time: 100ms
usb 1-6.3: uevent
hub 1-6.3:1.0: local power source is good
hub 1-6.3:1.0: enabling power on all ports
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev1.8
drivers/usb/core/inode.c: creating file '008'
PM: Adding info for No Bus:ep_00
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 2-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
usb 1-6.3: uevent
PM: Adding info for No Bus:device-mapper
device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
hub 1-6.3:1.0: port 3: status 0301 change 0001
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
PM: Adding info for No Bus:dm-0
PM: Adding info for No Bus:254:0
PM: Adding info for No Bus:dm-1
PM: Adding info for No Bus:254:1
PM: Adding info for No Bus:dm-2
PM: Adding info for No Bus:254:2
PM: Adding info for No Bus:dm-3
PM: Adding info for No Bus:254:3
PM: Adding info for No Bus:dm-4
PM: Adding info for No Bus:254:4
PM: Adding info for No Bus:dm-5
PM: Adding info for No Bus:254:5
PM: Adding info for No Bus:dm-6
PM: Adding info for No Bus:254:6
PM: Removing info for No Bus:254:1
PM: Removing info for No Bus:dm-1
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130301 PRSC PESC CSC LSDA PPS CCS
hub 2-0:1.0: unable to enumerate USB device on port 1
hub 1-3.1:1.0: state 7 ports 4 chg 0006 evt 0000
hub 1-3.1:1.0: port 1, status 0301, change 0000, 1.5 Mb/s
hub 1-3.1:1.0: port 1 not reset yet, waiting 10ms
usb 1-6.3: link qh128-0e01/c1df1000 start 4 [1/2 us]
usb 1-3.1.1: new low speed USB device using ehci_hcd and address 9
hub 1-3.1:1.0: port 1 not reset yet, waiting 10ms
usb 1-3.1.1: skipped 1 descriptor after interface
usb 1-3.1.1: skipped 1 descriptor after interface
usb 1-3.1.1: default language 0x0409
usb 1-3.1.1: udev 9, busnum 1, minor = 8
usb 1-3.1.1: New USB device found, idVendor=10d5, idProduct=0004
usb 1-3.1.1: New USB device strings: Mfr=0, Product=2, SerialNumber=0
usb 1-3.1.1: Product: PS2 to USB AdapterA3
PM: Adding info for usb:1-3.1.1
usb 1-3.1.1: uevent
usb 1-3.1.1: usb_probe_device
usb 1-3.1.1: configuration #1 chosen from 1 choice
usb 1-3.1.1: uevent
usb 1-3.1.1: adding 1-3.1.1:1.0 (config #1, interface 0)
PM: Adding info for usb:1-3.1.1:1.0
usb 1-3.1.1:1.0: uevent
usbhid 1-3.1.1:1.0: usb_probe_interface
usbhid 1-3.1.1:1.0: usb_probe_interface - got id
PM: Adding info for hid:0003:10D5:0004.0002
PM: Adding info for No Bus:input1
input: PS2 to USB AdapterA3 as /devices/pci0000:00/0000:00:0b.1/usb1/1-3/1-3.1/1-3.1.1/1-3.1.1:1.0/input/input1
usb 1-3.1.1: link qh8-0e01/c1df1940 start 5 [1/2 us]
generic-usb 0003:10D5:0004.0002: input: USB HID v1.10 Keyboard [PS2 to USB AdapterA3] on usb-0000:00:0b.1-3.1.1/input0
PM: Adding info for No Bus:ep_81
usb 1-3.1.1: adding 1-3.1.1:1.1 (config #1, interface 1)
PM: Adding info for usb:1-3.1.1:1.1
usb 1-3.1.1:1.1: uevent
usbhid 1-3.1.1:1.1: usb_probe_interface
usbhid 1-3.1.1:1.1: usb_probe_interface - got id
PM: Adding info for hid:0003:10D5:0004.0003
PM: Adding info for No Bus:input2
input: PS2 to USB AdapterA3 as /devices/pci0000:00/0000:00:0b.1/usb1/1-3/1-3.1/1-3.1.1/1-3.1.1:1.1/input/input2
usb 1-3.1.1: link qh8-0e01/c1df1a40 start 6 [1/2 us]
PM: Adding info for No Bus:mouse1
generic-usb 0003:10D5:0004.0003: input: USB HID v1.10 Mouse [PS2 to USB AdapterA3] on usb-0000:00:0b.1-3.1.1/input1
PM: Adding info for No Bus:ep_82
PM: Adding info for No Bus:usbdev1.9
drivers/usb/core/inode.c: creating file '009'
PM: Adding info for No Bus:ep_00
usb 1-3.1.1: uevent
hub 1-3.1:1.0: port 2, status 0101, change 0000, 12 Mb/s
hub 1-3.1:1.0: port 2 not reset yet, waiting 10ms
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
xor: automatically using best checksumming function: pIII_sse
pIII_sse : 7516.000 MB/sec
xor: using function: pIII_sse (7516.000 MB/sec)
raid6: int32x1 878 MB/s
raid6: int32x2 839 MB/s
usb 1-3.1.2: new high speed USB device using ehci_hcd and address 10
hub 1-3.1:1.0: port 2 not reset yet, waiting 10ms
raid6: int32x4 703 MB/s
raid6: int32x8 585 MB/s
raid6: mmxx1 2742 MB/s
raid6: mmxx2 3164 MB/s
raid6: sse1x1 1886 MB/s
usb 1-3.1.2: default language 0x0409
usb 1-3.1.2: udev 10, busnum 1, minor = 9
usb 1-3.1.2: New USB device found, idVendor=05e3, idProduct=0605
usb 1-3.1.2: New USB device strings: Mfr=0, Product=1, SerialNumber=0
usb 1-3.1.2: Product: USB2.0 Hub
PM: Adding info for usb:1-3.1.2
usb 1-3.1.2: uevent
usb 1-3.1.2: usb_probe_device
usb 1-3.1.2: configuration #1 chosen from 1 choice
usb 1-3.1.2: adding 1-3.1.2:1.0 (config #1, interface 0)
PM: Adding info for usb:1-3.1.2:1.0
usb 1-3.1.2:1.0: uevent
hub 1-3.1.2:1.0: usb_probe_interface
hub 1-3.1.2:1.0: usb_probe_interface - got id
hub 1-3.1.2:1.0: USB hub found
hub 1-3.1.2:1.0: 4 ports detected
hub 1-3.1.2:1.0: standalone hub
hub 1-3.1.2:1.0: individual port power switching
hub 1-3.1.2:1.0: individual port over-current protection
hub 1-3.1.2:1.0: Single TT
hub 1-3.1.2:1.0: TT requires at most 32 FS bit times (2664 ns)
hub 1-3.1.2:1.0: Port indicators are supported
hub 1-3.1.2:1.0: power on to power good time: 100ms
hub 1-3.1.2:1.0: local power source is good
hub 1-3.1.2:1.0: enabling power on all ports
usb 1-3.1.2: uevent
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev1.10
drivers/usb/core/inode.c: creating file '010'
PM: Adding info for No Bus:ep_00
hub 1-6:1.0: state 7 ports 4 chg 0000 evt 0002
usb 1-3.1.2: uevent
hub 1-6.3:1.0: state 7 ports 4 chg 0008 evt 0000
hub 1-6.3:1.0: port 3, status 0301, change 0000, 1.5 Mb/s
raid6: sse1x2 2425 MB/s
raid6: sse2x1 3542 MB/s
raid6: sse2x2 4222 MB/s
raid6: using algorithm sse2x2 (4222 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
md: raid10 personality registered for level 10
usb 1-6.3.3: new low speed USB device using ehci_hcd and address 11
hub 1-3.1.2:1.0: port 1: status 0101 change 0001
hub 1-3.1.2:1.0: port 2: status 0301 change 0001
usb 1-6.3.3: skipped 1 descriptor after interface
usb 1-6.3.3: skipped 1 descriptor after interface
usb 1-6.3.3: default language 0x0409
usb 1-6.3.3: udev 11, busnum 1, minor = 10
usb 1-6.3.3: New USB device found, idVendor=2222, idProduct=0013
usb 1-6.3.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-6.3.3: Product: Macally iKeySlim
usb 1-6.3.3: Manufacturer: Macally Peripherals
PM: Adding info for usb:1-6.3.3
usb 1-6.3.3: uevent
usb 1-6.3.3: usb_probe_device
usb 1-6.3.3: configuration #1 chosen from 1 choice
usb 1-6.3.3: uevent
usb 1-6.3.3: adding 1-6.3.3:1.0 (config #1, interface 0)
PM: Adding info for usb:1-6.3.3:1.0
usb 1-6.3.3:1.0: uevent
usbhid 1-6.3.3:1.0: usb_probe_interface
usbhid 1-6.3.3:1.0: usb_probe_interface - got id
PM: Adding info for hid:0003:2222:0013.0004
PM: Adding info for No Bus:input3
input: Macally Peripherals Macally iKeySlim as /devices/pci0000:00/0000:00:0b.1/usb1/1-6/1-6.3/1-6.3.3/1-6.3.3:1.0/input/input3
usb 1-6.3.3: link qh8-0e01/c1df1d80 start 7 [1/2 us]
generic-usb 0003:2222:0013.0004: input: USB HID v1.10 Keyboard [Macally Peripherals Macally iKeySlim] on usb-0000:00:0b.1-6.3.3/input0
PM: Adding info for No Bus:ep_81
usb 1-6.3.3: adding 1-6.3.3:1.1 (config #1, interface 1)
PM: Adding info for usb:1-6.3.3:1.1
usb 1-6.3.3:1.1: uevent
usbhid 1-6.3.3:1.1: usb_probe_interface
usbhid 1-6.3.3:1.1: usb_probe_interface - got id
PM: Adding info for hid:0003:2222:0013.0005
PM: Adding info for No Bus:input4
input: Macally Peripherals Macally iKeySlim as /devices/pci0000:00/0000:00:0b.1/usb1/1-6/1-6.3/1-6.3.3/1-6.3.3:1.1/input/input4
usb 1-6.3.3: link qh8-0e01/c1df1ec0 start 0 [1/2 us]
PM: Adding info for No Bus:mouse2
generic-usb 0003:2222:0013.0005: input: USB HID v1.10 Mouse [Macally Peripherals Macally iKeySlim] on usb-0000:00:0b.1-6.3.3/input1
PM: Adding info for No Bus:ep_82
PM: Adding info for No Bus:usbdev1.11
drivers/usb/core/inode.c: creating file '011'
PM: Adding info for No Bus:ep_00
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 2-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
usb 1-6.3.3: uevent
usb 1-3.1.2: link qh256-0001/c1df12c0 start 9 [1/0 us]
PM: Marking nosave pages: 000000000009c000 - 0000000000100000
PM: Basic memory bitmaps created
PM: Basic memory bitmaps freed
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
EXT3-fs: mounted filesystem with writeback data mode.
kjournald starting. Commit interval 5 seconds
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 2-0:1.0: unable to enumerate USB device on port 1
hub 1-3.1.2:1.0: state 7 ports 4 chg 0006 evt 0000
hub 1-3.1.2:1.0: port 1, status 0101, change 0000, 12 Mb/s
usb 1-3.1.2.1: new high speed USB device using ehci_hcd and address 12
hub 1-3.1.2:1.0: port 1 not reset yet, waiting 10ms
usb 1-3.1.2.1: default language 0x0409
usb 1-3.1.2.1: udev 12, busnum 1, minor = 11
usb 1-3.1.2.1: New USB device found, idVendor=090c, idProduct=1000
usb 1-3.1.2.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-3.1.2.1: Product: DISK 2.0
usb 1-3.1.2.1: Manufacturer: USB
usb 1-3.1.2.1: SerialNumber: PHN84K6AD8PLXSVC
PM: Adding info for usb:1-3.1.2.1
usb 1-3.1.2.1: uevent
usb 1-3.1.2.1: usb_probe_device
usb 1-3.1.2.1: configuration #1 chosen from 1 choice
usb 1-3.1.2.1: adding 1-3.1.2.1:1.0 (config #1, interface 0)
PM: Adding info for usb:1-3.1.2.1:1.0
usb 1-3.1.2.1:1.0: uevent
usb-storage 1-3.1.2.1:1.0: usb_probe_interface
usb-storage 1-3.1.2.1:1.0: usb_probe_interface - got id
scsi5 : SCSI emulation for USB Mass Storage devices
PM: Adding info for scsi:host5
PM: Adding info for No Bus:host5
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:ep_02
PM: Adding info for No Bus:usbdev1.12
drivers/usb/core/inode.c: creating file '012'
PM: Adding info for No Bus:ep_00
usb-storage: device found at 12
usb-storage: waiting for device to settle before scanning
hub 1-3.1.2:1.0: port 2, status 0301, change 0000, 1.5 Mb/s
hub 1-3.1.2:1.0: port 2 not reset yet, waiting 10ms
usb 1-3.1.2.2: new low speed USB device using ehci_hcd and address 13
usb 1-3.1.2.2: skipped 1 descriptor after interface
usb 1-3.1.2.2: default language 0x0409
usb 1-3.1.2.2: udev 13, busnum 1, minor = 12
usb 1-3.1.2.2: New USB device found, idVendor=046d, idProduct=c050
usb 1-3.1.2.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-3.1.2.2: Product: USB-PS/2 Optical Mouse
usb 1-3.1.2.2: Manufacturer: Logitech
PM: Adding info for usb:1-3.1.2.2
usb 1-3.1.2.2: uevent
usb 1-3.1.2.2: usb_probe_device
usb 1-3.1.2.2: configuration #1 chosen from 1 choice
usb 1-3.1.2.2: adding 1-3.1.2.2:1.0 (config #1, interface 0)
PM: Adding info for usb:1-3.1.2.2:1.0
usb 1-3.1.2.2:1.0: uevent
usbhid 1-3.1.2.2:1.0: usb_probe_interface
usbhid 1-3.1.2.2:1.0: usb_probe_interface - got id
PM: Adding info for hid:0003:046D:C050.0006
PM: Adding info for No Bus:input5
input: Logitech USB-PS/2 Optical Mouse as /devices/pci0000:00/0000:00:0b.1/usb1/1-3/1-3.1/1-3.1.2/1-3.1.2.2/1-3.1.2.2:1.0/input/input5
PM: Adding info for No Bus:mouse3
generic-usb 0003:046D:C050.0006: input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:0b.1-3.1.2.2/input0
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev1.13
drivers/usb/core/inode.c: creating file '013'
PM: Adding info for No Bus:ep_00
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030300 PESC CSC LSDA PPS
hub 2-0:1.0: port 1, status 0300, change 0003, 1.5 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x300
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 1-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 1-3.1.2:1.0: state 7 ports 4 chg 0000 evt 0004
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00010301 CSC LSDA PPS CCS
hub 2-0:1.0: port 1, status 0301, change 0001, 1.5 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 2-0:1.0: unable to enumerate USB device on port 1
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030300 PESC CSC LSDA PPS
hub 2-0:1.0: port 1, status 0300, change 0003, 1.5 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x300
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 1-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00010301 CSC LSDA PPS CCS
hub 2-0:1.0: port 1, status 0301, change 0001, 1.5 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 2-0:1.0: unable to enumerate USB device on port 1
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 1-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 2-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 2-0:1.0: unable to enumerate USB device on port 1
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 1-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
udev: starting version 146
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 2-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
usb usb2: uevent
usb 2-0:1.0: uevent
usb usb1: uevent
usb 1-0:1.0: uevent
usb 1-2: uevent
usb 1-2:1.0: uevent
usb 1-3: uevent
usb 1-3.1: uevent
usb 1-3.1.1: uevent
usb 1-3.1.1:1.0: uevent
usb 1-3.1.1:1.1: uevent
usb 1-3.1.2: uevent
usb 1-3.1.2.1: uevent
usb 1-3.1.2.1:1.0: uevent
usb 1-3.1.2.2: uevent
usb 1-3.1.2.2:1.0: uevent
usb 1-3.1.2:1.0: uevent
usb 1-3.1:1.0: uevent
usb 1-3:1.0: uevent
usb 1-6: uevent
usb 1-6.1: uevent
usb 1-6.1:1.0: uevent
usb 1-6.3: uevent
usb 1-6.3.3: uevent
usb 1-6.3.3:1.0: uevent
usb 1-6.3.3:1.1: uevent
usb 1-6.3:1.0: uevent
usb 1-6:1.0: uevent
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
usb usb2: uevent
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 2-0:1.0: unable to enumerate USB device on port 1
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 1-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
usb usb2: uevent
usb usb1: uevent
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
usb usb1: uevent
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 2-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
usb 1-2: uevent
usb 1-3: uevent
usb 1-6: uevent
usb 1-2: uevent
usb 1-3: uevent
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
usb 1-6: uevent
PM: Adding info for No Bus:rtc
Real Time Clock Driver v1.12b
usb 1-6.1: uevent
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 2-0:1.0: unable to enumerate USB device on port 1
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 1-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
usb 1-3.1: uevent
usb 1-6.3: uevent
usb 1-6.1: uevent
usb 1-3.1: uevent
usb 1-6.3: uevent
usb 1-3.1.1: uevent
usb 1-3.1.1: uevent
usb 1-6.3.3: uevent
usb 1-3.1.2: uevent
usb 1-3.1.2: uevent
usb 1-6.3.3: uevent
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
usb 1-3.1.2.2: uevent
usb 1-3.1.2.1: uevent
usb 1-3.1.2.2: uevent
usb 1-3.1.2.1: uevent
PM: Adding info for No Bus:input6
input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input6
ACPI: Power Button [PWRB]
PM: Adding info for No Bus:input7
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input7
ACPI: Power Button [PWRF]
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 2-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 2-0:1.0: unable to enumerate USB device on port 1
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 1-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
PM: Adding info for No Bus:raw1394
ieee1394: raw1394: /dev/raw1394 device initialized
PM: Adding info for No Bus:event0
PM: Adding info for No Bus:event1
PM: Adding info for No Bus:event2
PM: Adding info for No Bus:event3
PM: Adding info for No Bus:event4
PM: Adding info for No Bus:event5
PM: Adding info for No Bus:event6
PM: Adding info for No Bus:event7
usb 1-3.1.2.2:1.0: uevent
usb 1-3.1.2.2: uevent
usb 1-3.1.2.2:1.0: uevent
usb 1-3.1.2.2: uevent
usb 1-3.1.2.2:1.0: uevent
usb 1-3.1.2.2:1.0: uevent
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 2-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
ACPI: SSDT 7fefa940 00175 (v01 Nvidia ASUSACPI 42302E31 AWRD 00000000)
PM: Adding info for No Bus:cooling_device1
processor LNXCPU:00: registered as cooling_device1
ACPI: SSDT 7fefad50 000CE (v01 Nvidia ASUSACPI 42302E31 AWRD 00000000)
PM: Adding info for No Bus:cooling_device2
processor LNXCPU:01: registered as cooling_device2
PM: Adding info for No Bus:hwmon0
usb 1-3.1.1:1.1: uevent
usb 1-3.1.1: uevent
usb 1-6.1:1.0: uevent
usb 1-6.1: uevent
usb 1-6.1:1.0: uevent
usb 1-6.1: uevent
usb 1-3.1.1:1.1: uevent
usb 1-3.1.1: uevent
usb 1-3.1.1:1.0: uevent
usb 1-3.1.1: uevent
usb 1-3.1.1:1.1: uevent
usb 1-3.1.1:1.1: uevent
usb 1-6.1:1.0: uevent
usb 1-3.1.1:1.0: uevent
usb 1-6.1:1.0: uevent
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 2-0:1.0: unable to enumerate USB device on port 1
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 1-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
usb 1-6.3.3:1.1: uevent
usb 1-6.3.3:1.1: uevent
usb 1-6.3.3: uevent
usb 1-6.3.3: uevent
usb 1-6.3.3:1.0: uevent
usb 1-6.3.3: uevent
usb 1-6.3.3:1.1: uevent
usb 1-6.3.3:1.1: uevent
usb 1-6.3.3:1.0: uevent
sr0: scsi3-mmc drive: 32x/32x cd/rw xa/form2 cdda tray
PM: Adding info for No Bus:sr0
PM: Adding info for No Bus:11:0
sr 3:0:0:0: Attached scsi CD-ROM sr0
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 2-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
ACPI: I/O resource nForce2_smbus [0x5000-0x503f] conflicts with ACPI region SM00 [0x5000-0x5005]
ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
nForce2_smbus 0000:00:0a.1: Error probing SMB1.
PM: Adding info for i2c:i2c-0
i2c i2c-0: nForce2 SMBus adapter at 0x5100
PM: Adding info for No Bus:dv1394-0
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 2-0:1.0: unable to enumerate USB device on port 1
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 1-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
PM: Adding info for No Bus:sg0
sd 0:0:0:0: Attached scsi generic sg0 type 0
PM: Adding info for No Bus:sg1
sd 1:0:0:0: Attached scsi generic sg1 type 0
PM: Adding info for No Bus:sg2
sr 3:0:0:0: Attached scsi generic sg2 type 5
hda: UDMA/66 mode selected
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 2-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
PM: Adding info for No Bus:timer
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 2-0:1.0: unable to enumerate USB device on port 1
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 1-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
PM: Adding info for No Bus:seq
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 2-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
PM: Adding info for No Bus:sequencer
PM: Adding info for No Bus:sequencer2
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 2-0:1.0: unable to enumerate USB device on port 1
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030300 PESC CSC LSDA PPS
hub 2-0:1.0: port 1, status 0300, change 0003, 1.5 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x300
scsi 4:0:0:0: Direct-Access Generic USB SD Reader 1.00 PQ: 0 ANSI: 0
PM: Adding info for scsi:target4:0:0
PM: Adding info for scsi:4:0:0:0
PM: Adding info for No Bus:4:0:0:0
PM: Adding info for No Bus:4:0:0:0
PM: Adding info for No Bus:sg3
sd 4:0:0:0: Attached scsi generic sg3 type 0
PM: Adding info for No Bus:4:0:0:0
scsi 4:0:0:1: Direct-Access Generic USB CF Reader 1.01 PQ: 0 ANSI: 0
PM: Adding info for scsi:4:0:0:1
PM: Adding info for No Bus:4:0:0:1
PM: Adding info for No Bus:4:0:0:1
PM: Adding info for No Bus:sg4
sd 4:0:0:1: Attached scsi generic sg4 type 0
PM: Adding info for No Bus:4:0:0:1
scsi 4:0:0:2: Direct-Access Generic USB SM Reader 1.02 PQ: 0 ANSI: 0
PM: Adding info for scsi:4:0:0:2
PM: Adding info for No Bus:4:0:0:2
PM: Adding info for No Bus:4:0:0:2
PM: Adding info for No Bus:sg5
sd 4:0:0:2: Attached scsi generic sg5 type 0
PM: Adding info for No Bus:4:0:0:2
scsi 4:0:0:3: Direct-Access Generic USB MS Reader 1.03 PQ: 0 ANSI: 0
PM: Adding info for scsi:4:0:0:3
PM: Adding info for No Bus:4:0:0:3
PM: Adding info for No Bus:4:0:0:3
PM: Adding info for No Bus:sg6
sd 4:0:0:3: Attached scsi generic sg6 type 0
PM: Adding info for No Bus:4:0:0:3
usb-storage: device scan complete
PM: Adding info for No Bus:sdc
PM: Adding info for No Bus:8:32
ACPI: PCI Interrupt Link [AAZA] enabled at IRQ 23
sd 4:0:0:0: [sdc] Attached SCSI removable disk
HDA Intel 0000:00:10.1: PCI INT B -> Link[AAZA] -> GSI 23 (level, low) -> IRQ 23
HDA Intel 0000:00:10.1: setting latency timer to 64
PM: Adding info for No Bus:sdd
PM: Adding info for No Bus:8:48
sd 4:0:0:1: [sdd] Attached SCSI removable disk
PM: Adding info for No Bus:sdf
PM: Adding info for No Bus:8:80
PM: Adding info for No Bus:sde
PM: Adding info for No Bus:8:64
sd 4:0:0:3: [sdf] Attached SCSI removable disk
sd 4:0:0:2: [sde] Attached SCSI removable disk
usb 1-2:1.0: uevent
usb 1-2: uevent
usb 1-2:1.0: uevent
usb 1-2:1.0: uevent
usb 1-2: uevent
usb 1-2: uevent
usb 1-2:1.0: uevent
usb 1-2: uevent
usb 1-2:1.0: uevent
usb 1-2:1.0: uevent
usb 1-2:1.0: uevent
usb 1-2:1.0: uevent
PM: Adding info for No Bus:input8
input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:10.1/input/input8
PM: Adding info for No Bus:event8
PM: Adding info for No Bus:card0
PM: Adding info for No Bus:pcmC0D1p
PM: Adding info for No Bus:adsp
PM: Adding info for No Bus:pcmC0D0p
PM: Adding info for No Bus:pcmC0D0c
PM: Adding info for No Bus:dsp
PM: Adding info for No Bus:audio
PM: Adding info for No Bus:hwC0D0
PM: Adding info for No Bus:controlC0
PM: Adding info for No Bus:mixer
PM: Adding info for No Bus:vcs2
PM: Adding info for No Bus:vcsa2
PM: Adding info for No Bus:vcs3
PM: Adding info for No Bus:vcsa3
PM: Adding info for No Bus:vcs4
PM: Adding info for No Bus:vcsa4
PM: Adding info for No Bus:vcs5
PM: Adding info for No Bus:vcsa5
PM: Adding info for No Bus:vcs6
PM: Adding info for No Bus:vcsa6
ohci_hcd 0000:00:0b.0: auto-stop root hub
hda: UDMA/66 mode selected
scsi 5:0:0:0: Direct-Access USB DISK 2.0 0403 PQ: 0 ANSI: 0 CCS
PM: Adding info for scsi:target5:0:0
PM: Adding info for scsi:5:0:0:0
PM: Adding info for No Bus:5:0:0:0
PM: Adding info for No Bus:5:0:0:0
PM: Adding info for No Bus:sg7
sd 5:0:0:0: Attached scsi generic sg7 type 0
PM: Adding info for No Bus:5:0:0:0
usb-storage: device scan complete
sd 5:0:0:0: [sdg] 3981312 512-byte logical blocks: (2.03 GB/1.89 GiB)
sd 5:0:0:0: [sdg] Write Protect is off
sd 5:0:0:0: [sdg] Mode Sense: 43 00 00 00
sd 5:0:0:0: [sdg] Assuming drive cache: write through
PM: Adding info for No Bus:sdg
sd 5:0:0:0: [sdg] Assuming drive cache: write through
sdg: sdg1
PM: Adding info for No Bus:sdg1
PM: Adding info for No Bus:8:96
sd 5:0:0:0: [sdg] Assuming drive cache: write through
sd 5:0:0:0: [sdg] Attached SCSI removable disk
usb 1-3.1.2.1:1.0: uevent
usb 1-3.1.2.1: uevent
usb 1-3.1.2.1:1.0: uevent
usb 1-3.1.2.1:1.0: uevent
usb 1-3.1.2.1: uevent
usb 1-3.1.2.1:1.0: uevent
EXT3 FS on dm-2, internal journal
i2c /dev entries driver
PM: Adding info for No Bus:i2c-0
it87: Found IT8712F chip at 0x290, revision 7
it87: in3 is VCC (+5V)
it87: in7 is VCCH (+5V Stand-By)
ACPI: I/O resource it87 [0x295-0x296] conflicts with ACPI region HWRE [0x295-0x296]
ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
fuse init (API version 7.13)
PM: Adding info for No Bus:fuse
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-5, internal journal
EXT3-fs: mounted filesystem with writeback data mode.
PM: Adding info for No Bus:254:3-fuseblk
PM: Adding info for No Bus:254:6-fuseblk
Adding 4194296k swap on /mnt/oldlin/4G-memory.swap. Priority:-1 extents:1057 across:4264956k
r8169: eth1: link up
NET: Registered protocol family 17
r8169: eth1: link up
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PM: Adding info for No Bus:0:16
PM: Adding info for No Bus:0:17
PM: Adding info for No Bus:0:18
PM: Adding info for No Bus:vcs10
PM: Adding info for No Bus:vcsa10
usb 1-6.1: link qh8-0e01/c1eabd80 start 2 [1/2 us]
usb 1-3.1.2.2: link qh8-0e01/c1eabdc0 start 3 [1/2 us]
usb 1-6.1: unlink qh8-0e01/c1eabd80 start 2 [1/2 us]
usb 1-3.1.2.2: unlink qh8-0e01/c1eabdc0 start 3 [1/2 us]
ehci_hcd 0000:00:0b.1: reused qh c1eabd80 schedule
usb 1-6.1: link qh8-0e01/c1eabd80 start 2 [1/2 us]
ehci_hcd 0000:00:0b.1: reused qh c1eabdc0 schedule
usb 1-3.1.2.2: link qh8-0e01/c1eabdc0 start 3 [1/2 us]
irda_init()
NET: Registered protocol family 23
usbcore: registered new interface driver stir4200
usb 1-2:1.0: uevent
usb 1-2: uevent
usb 1-2:1.0: uevent
usb 1-2:1.0: uevent
usb 1-2: uevent
usb 1-2:1.0: uevent
usb 1-2:1.0: uevent
usb 1-2: uevent
usb 1-2:1.0: uevent
usb 1-2:1.0: uevent
usb 1-2: uevent
usb 1-3.1.2.1:1.0: uevent
usb 1-3.1.2.1: uevent
usb 1-2:1.0: uevent
usb 1-3.1.2.1:1.0: uevent
warning: `ntpd' uses 32-bit capabilities (legacy support in use)
usb usb2: uevent
usb 2-0:1.0: uevent
usb usb1: uevent
usb 1-0:1.0: uevent
usb 1-2: uevent
usb 1-2:1.0: uevent
usb 1-3: uevent
usb 1-3.1: uevent
usb 1-3.1.1: uevent
usb 1-3.1.1:1.0: uevent
usb 1-3.1.1:1.1: uevent
usb 1-3.1.2: uevent
usb 1-3.1.2.1: uevent
usb 1-3.1.2.1:1.0: uevent
usb 1-3.1.2.2: uevent
usb 1-3.1.2.2:1.0: uevent
usb 1-3.1.2:1.0: uevent
usb 1-3.1:1.0: uevent
usb 1-3:1.0: uevent
usb 1-6: uevent
usb 1-6.1: uevent
usb 1-6.1:1.0: uevent
usb 1-6.3: uevent
usb 1-6.3.3: uevent
usb 1-6.3.3:1.0: uevent
usb 1-6.3.3:1.1: uevent
usb 1-6.3:1.0: uevent
usb 1-6:1.0: uevent
Bluetooth: Core ver 2.15
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.14
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM ver 1.11
Bluetooth: SCO (Voice Link) ver 0.6
Bluetooth: SCO socket layer initialized
CPUFREQ: Per core ondemand sysfs interface is deprecated - up_threshold
CPUFREQ: Per core ondemand sysfs interface is deprecated - ignore_nice_load
PM: Adding info for No Bus:vcs7
PM: Adding info for No Bus:vcsa7
Linux agpgart interface v0.103
nvidia: module license 'NVIDIA' taints kernel.
Disabling lock debugging due to kernel taint
ACPI: PCI Interrupt Link [APC5] enabled at IRQ 16
nvidia 0000:01:00.0: PCI INT A -> Link[APC5] -> GSI 16 (level, low) -> IRQ 16
nvidia 0000:01:00.0: setting latency timer to 64
NVRM: loading NVIDIA UNIX x86 Kernel Module 185.18.36 Fri Aug 14 17:18:04 PDT 2009
PM: Adding info for i2c:i2c-1
PM: Adding info for No Bus:i2c-1
PM: Adding info for i2c:i2c-2
PM: Adding info for No Bus:i2c-2
PM: Adding info for i2c:i2c-3
PM: Adding info for No Bus:i2c-3
usb usb1: uevent
usb 1-0:1.0: uevent
usb usb2: uevent
usb 2-0:1.0: uevent
usb 1-2: uevent
usb 1-2:1.0: uevent
usb 1-3: uevent
usb 1-3:1.0: uevent
usb 1-6: uevent
usb 1-6:1.0: uevent
usb 1-3.1: uevent
usb 1-3.1:1.0: uevent
usb 1-6.1: uevent
usb 1-6.1:1.0: uevent
usb 1-6.3: uevent
usb 1-6.3:1.0: uevent
usb 1-3.1.1: uevent
usb 1-3.1.1:1.0: uevent
usb 1-3.1.1:1.1: uevent
usb 1-3.1.2: uevent
usb 1-3.1.2:1.0: uevent
usb 1-6.3.3: uevent
usb 1-6.3.3:1.0: uevent
usb 1-6.3.3:1.1: uevent
usb 1-3.1.2.1: uevent
usb 1-3.1.2.1:1.0: uevent
usb 1-3.1.2.2: uevent
usb 1-3.1.2.2:1.0: uevent
usb usb2: uevent
usb 2-0:1.0: uevent
usb usb1: uevent
usb 1-0:1.0: uevent
usb 1-2: uevent
usb 1-2:1.0: uevent
usb 1-3: uevent
usb 1-3.1: uevent
usb 1-3.1.1: uevent
usb 1-3.1.1:1.0: uevent
usb 1-3.1.1:1.1: uevent
usb 1-3.1.2: uevent
usb 1-3.1.2.1: uevent
usb 1-3.1.2.1:1.0: uevent
usb 1-3.1.2.2: uevent
usb 1-3.1.2.2:1.0: uevent
usb 1-3.1.2:1.0: uevent
usb 1-3.1:1.0: uevent
usb 1-3:1.0: uevent
usb 1-6: uevent
usb 1-6.1: uevent
usb 1-6.1:1.0: uevent
usb 1-6.3: uevent
usb 1-6.3.3: uevent
usb 1-6.3.3:1.0: uevent
usb 1-6.3.3:1.1: uevent
usb 1-6.3:1.0: uevent
usb 1-6:1.0: uevent
CPU0 attaching NULL sched-domain.
CPU1 attaching NULL sched-domain.
CPU0 attaching sched-domain:
domain 0: span 0-1 level MC
groups: 0 1
CPU1 attaching sched-domain:
domain 0: span 0-1 level MC
groups: 1 0
usb usb2: uevent
usb 2-0:1.0: uevent
usb usb1: uevent
usb 1-0:1.0: uevent
usb 1-2: uevent
usb 1-2:1.0: uevent
usb 1-3: uevent
usb 1-3.1: uevent
usb 1-3.1.1: uevent
usb 1-3.1.1:1.0: uevent
usb 1-3.1.1:1.1: uevent
usb 1-3.1.2: uevent
usb 1-3.1.2.1: uevent
usb 1-3.1.2.1:1.0: uevent
usb 1-3.1.2.2: uevent
usb 1-3.1.2.2:1.0: uevent
usb 1-3.1.2:1.0: uevent
usb 1-3.1:1.0: uevent
usb 1-3:1.0: uevent
usb 1-6: uevent
usb 1-6.1: uevent
usb 1-6.1:1.0: uevent
usb 1-6.3: uevent
usb 1-6.3.3: uevent
usb 1-6.3.3:1.0: uevent
usb 1-6.3.3:1.1: uevent
usb 1-6.3:1.0: uevent
usb 1-6:1.0: uevent
UDF-fs: Partition marked readonly; forcing readonly mount
UDF-fs INFO UDF: Mounting volume 'XFACTOR_VOLUME6', timestamp 2004/09/19 17:13 (1000)
VFS: busy inodes on changed media or resized disk hda
VFS: busy inodes on changed media or resized disk hda
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
sr 3:0:0:0: [sr0] CDB: Read(10): 28 00 00 00 00 10 00 00 02 00
ata4.00: cmd a0/01:00:00:00:10/00:00:00:00:00/a0 tag 0 dma 4096 in
res 40/00:02:00:0c:00/00:00:00:00:00/a0 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for UDMA/100
ata4: EH complete
ata4: limiting SATA link speed to 1.5 Gbps
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
sr 3:0:0:0: [sr0] CDB: Read(10): 28 00 00 00 00 10 00 00 02 00
ata4.00: cmd a0/01:00:00:00:10/00:00:00:00:00/a0 tag 0 dma 4096 in
res 40/00:02:00:0c:00/00:00:00:00:00/a0 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for UDMA/100
ata4: EH complete
ata4.00: limiting speed to UDMA/66:PIO4
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
sr 3:0:0:0: [sr0] CDB: Read(10): 28 00 00 00 00 10 00 00 02 00
ata4.00: cmd a0/01:00:00:00:10/00:00:00:00:00/a0 tag 0 dma 4096 in
res 40/00:02:00:0c:00/00:00:00:00:00/a0 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for UDMA/66
ata4: EH complete
ata4.00: limiting speed to UDMA/33:PIO4
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
sr 3:0:0:0: [sr0] CDB: Read(10): 28 00 00 00 00 10 00 00 02 00
ata4.00: cmd a0/01:00:00:00:10/00:00:00:00:00/a0 tag 0 dma 4096 in
res 40/00:02:00:0c:00/00:00:00:00:00/a0 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for UDMA/33
sr 3:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
sr 3:0:0:0: [sr0] Sense Key : Aborted Command [current] [descriptor]
Descriptor sense data with sense descriptors (in hex):
72 0b 00 00 00 00 00 0e 09 0c 00 00 00 02 00 00
00 0c 00 00 a0 40
sr 3:0:0:0: [sr0] Add. Sense: No additional sense information
sr 3:0:0:0: [sr0] CDB: Read(10): 28 00 00 00 00 10 00 00 02 00
end_request: I/O error, dev sr0, sector 64
Buffer I/O error on device sr0, logical block 8
ata4: EH complete
r8169: eth1: link up
ata4.00: limiting speed to PIO4
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
sr 3:0:0:0: [sr0] CDB: Read(10): 28 00 00 00 00 10 00 00 02 00
ata4.00: cmd a0/01:00:00:00:10/00:00:00:00:00/a0 tag 0 dma 4096 in
res 40/00:03:00:fe:00/00:00:00:00:00/a0 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO4
ata4: EH complete
ehci_hcd 0000:00:0b.1: detected XactErr len 0/31 retry 1
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: sata_nv times out for BD-ROM iHOS104-08
2010-02-28 17:24 ` Cengiz Günay
@ 2010-03-02 11:48 ` Tejun Heo
2010-03-08 19:17 ` Cengiz Günay
0 siblings, 1 reply; 28+ messages in thread
From: Tejun Heo @ 2010-03-02 11:48 UTC (permalink / raw)
To: Cengiz Günay; +Cc: Robert Hancock, linux-kernel, linux-ide
[-- Attachment #1: Type: text/plain, Size: 421 bytes --]
Hello,
On 03/01/2010 02:24 AM, Cengiz Günay wrote:
> Before and after the swncq-atapi-pio patch I still get awful read
> times from the BD-ROM drive:
>
> $ time dd if=/dev/sr0 of=/dev/null bs=64k count=1024
> 67108864 bytes (67 MB) copied, 106.945 seconds, 628 kB/s
> => real 1m46.977s
Hmmm... the drive is timing out even on 4k READ10's. This shouldn't
really be happening. Can you please try this one?
--
tejun
[-- Attachment #2: swncq-atapi-pio-2.patch --]
[-- Type: text/x-patch, Size: 1742 bytes --]
diff --git a/drivers/ata/sata_nv.c b/drivers/ata/sata_nv.c
index 0c82d33..84d3eba 100644
--- a/drivers/ata/sata_nv.c
+++ b/drivers/ata/sata_nv.c
@@ -307,6 +307,7 @@ static int nv_scr_write(struct ata_link *link, unsigned int sc_reg, u32 val);
static int nv_hardreset(struct ata_link *link, unsigned int *class,
unsigned long deadline);
+static int nv_check_atapi_dma(struct ata_queued_cmd *qc);
static void nv_nf2_freeze(struct ata_port *ap);
static void nv_nf2_thaw(struct ata_port *ap);
static void nv_ck804_freeze(struct ata_port *ap);
@@ -470,6 +471,7 @@ static struct ata_port_operations nv_generic_ops = {
.scr_read = nv_scr_read,
.scr_write = nv_scr_write,
.hardreset = nv_hardreset,
+ .check_atapi_dma = nv_check_atapi_dma,
};
static struct ata_port_operations nv_nf2_ops = {
@@ -585,7 +587,7 @@ static const struct ata_port_info nv_port_info[] = {
/* SWNCQ */
{
.flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
- ATA_FLAG_NCQ,
+ ATA_FLAG_NCQ | ATA_FLAG_PIO_POLLING,
.pio_mask = NV_PIO_MASK,
.mwdma_mask = NV_MWDMA_MASK,
.udma_mask = NV_UDMA_MASK,
@@ -1614,6 +1616,25 @@ static int nv_hardreset(struct ata_link *link, unsigned int *class,
return -EAGAIN;
}
+#include <scsi/scsi_cmnd.h>
+static int nv_check_atapi_dma(struct ata_queued_cmd *qc)
+{
+ /* Whitelist commands that may use DMA. */
+ switch (qc->scsicmd->cmnd[0]) {
+ case WRITE_12:
+ case WRITE_10:
+ case WRITE_6:
+ case READ_12:
+ case READ_10:
+ case READ_6:
+ case 0xad: /* READ_DVD_STRUCTURE */
+ case 0xbe: /* READ_CD */
+ if (ata_qc_raw_nbytes(qc) > 4096)
+ return 0;
+ }
+ return 1;
+}
+
static void nv_nf2_freeze(struct ata_port *ap)
{
void __iomem *scr_addr = ap->host->ports[0]->ioaddr.scr_addr;
^ permalink raw reply related [flat|nested] 28+ messages in thread
* Re: sata_nv times out for BD-ROM iHOS104-08
2010-03-02 11:48 ` Tejun Heo
@ 2010-03-08 19:17 ` Cengiz Günay
2010-03-08 23:46 ` Robert Hancock
2010-03-09 1:21 ` Tejun Heo
0 siblings, 2 replies; 28+ messages in thread
From: Cengiz Günay @ 2010-03-08 19:17 UTC (permalink / raw)
To: Tejun Heo; +Cc: Robert Hancock, linux-kernel, linux-ide
[-- Attachment #1: Type: text/plain, Size: 1144 bytes --]
Hello,
Sorry for the delay, I was confused about managing so many patches,
but I realized that you're sending me cumulative patches that I can
apply to the original. I just want to remind you that I still have the
patches to the other two files: libata-eh.c libata-sff.c
On Tue, Mar 2, 2010 at 6:48 AM, Tejun Heo <tj@kernel.org> wrote:
> Hmmm... the drive is timing out even on 4k READ10's. This shouldn't
> really be happening. Can you please try this one?
Applied. It did not change anything visibly (dmesg attached). I have
also been getting other SCSI errors since we started communicating
with the device (search for sr0 in dmesg). I wonder if they give any
hints? Here's one:
sr 4:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
sr 4:0:0:0: [sr0] Sense Key : Aborted Command [current] [descriptor]
Descriptor sense data with sense descriptors (in hex):
72 0b 00 00 00 00 00 0e 09 0c 00 00 00 02 00 00
00 20 00 00 a0 40
sr 4:0:0:0: [sr0] Add. Sense: No additional sense information
sr 4:0:0:0: [sr0] CDB: Read(10): 28 00 00 00 00 00 00 00 40 00
end_request: I/O error, dev sr0, sector 0
Thanks,
Cengiz
[-- Attachment #2: dmesg-sata_nv-swncq-atapi-pio-patch-2 --]
[-- Type: application/octet-stream, Size: 90870 bytes --]
Linux version 2.6.32testing (root@salon) (gcc version 4.3.3 (Debian 4.3.3-10) ) #6 SMP PREEMPT Mon Mar 8 13:09:55 EST 2010
KERNEL supported cpus:
Intel GenuineIntel
AMD AuthenticAMD
NSC Geode by NSC
Cyrix CyrixInstead
Centaur CentaurHauls
Transmeta GenuineTMx86
Transmeta TransmetaCPU
UMC UMC UMC UMC
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009c400 (usable)
BIOS-e820: 000000000009c400 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000007fef0000 (usable)
BIOS-e820: 000000007fef0000 - 000000007fef3000 (ACPI NVS)
BIOS-e820: 000000007fef3000 - 000000007ff00000 (ACPI data)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
DMI 2.4 present.
Phoenix BIOS detected: BIOS may corrupt low RAM, working around it.
e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
last_pfn = 0x7fef0 max_arch_pfn = 0x100000
MTRR default type: uncachable
MTRR fixed ranges enabled:
00000-9FFFF write-back
A0000-BFFFF uncachable
C0000-CDFFF write-protect
CE000-FFFFF uncachable
MTRR variable ranges enabled:
0 base 000000000 mask F80000000 write-back
1 base 07FF00000 mask FFFF00000 uncachable
2 disabled
3 disabled
4 disabled
5 disabled
6 disabled
7 disabled
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
initial memory mapped : 0 - 01800000
init_memory_mapping: 0000000000000000-00000000377fe000
0000000000 - 0000400000 page 4k
0000400000 - 0037400000 page 2M
0037400000 - 00377fe000 page 4k
kernel direct mapping tables up to 377fe000 @ 10000-15000
RAMDISK: 36bad000 - 37fef0ec
Allocated new RAMDISK: 013e6000 - 028280ec
Move RAMDISK from 0000000036bad000 - 0000000037fef0eb to 013e6000 - 028280eb
ACPI: RSDP 000f7900 00024 (v02 Nvidia)
ACPI: XSDT 7fef30c0 0004C (v01 Nvidia ASUSACPI 42302E31 AWRD 00000000)
ACPI: FACP 7fefa600 000F4 (v03 Nvidia ASUSACPI 42302E31 AWRD 00000000)
ACPI: DSDT 7fef3240 07354 (v01 NVIDIA ASUSACPI 00001000 MSFT 03000000)
ACPI: FACS 7fef0000 00040
ACPI: HPET 7fefa840 00038 (v01 Nvidia ASUSACPI 42302E31 AWRD 00000098)
ACPI: MCFG 7fefa8c0 0003C (v01 Nvidia ASUSACPI 42302E31 AWRD 00000000)
ACPI: APIC 7fefa740 0008E (v01 Nvidia ASUSACPI 42302E31 AWRD 00000000)
ACPI: SSDT 7fefae20 0032C (v01 Nvidia ASUSACPI 42302E31 AWRD 00000000)
ACPI: Local APIC address 0xfee00000
1158MB HIGHMEM available.
887MB LOWMEM available.
mapped low ram: 0 - 377fe000
low ram: 0 - 377fe000
node 0 low ram: 00000000 - 377fe000
node 0 bootmap 00011000 - 00017f00
(9 early reservations) ==> bootmem [0000000000 - 00377fe000]
#0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
#1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000]
#2 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 - 0000007000]
#3 [0001000000 - 00013de7c4] TEXT DATA BSS ==> [0001000000 - 00013de7c4]
#4 [000009c400 - 0000100000] BIOS reserved ==> [000009c400 - 0000100000]
#5 [00013df000 - 00013e5149] BRK ==> [00013df000 - 00013e5149]
#6 [0000010000 - 0000011000] PGTABLE ==> [0000010000 - 0000011000]
#7 [00013e6000 - 00028280ec] NEW RAMDISK ==> [00013e6000 - 00028280ec]
#8 [0000011000 - 0000018000] BOOTMAP ==> [0000011000 - 0000018000]
found SMP MP-table at [c00f5d50] f5d50
Zone PFN ranges:
DMA 0x00000010 -> 0x00001000
Normal 0x00001000 -> 0x000377fe
HighMem 0x000377fe -> 0x0007fef0
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
0: 0x00000010 -> 0x0000009c
0: 0x00000100 -> 0x0007fef0
On node 0 totalpages: 523900
free_area_init_node: node 0, pgdat c1324fc0, node_mem_map c282a200
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 3948 pages, LIFO batch:0
Normal zone: 1744 pages used for memmap
Normal zone: 221486 pages, LIFO batch:31
HighMem zone: 2318 pages used for memmap
HighMem zone: 294372 pages, LIFO batch:31
Using APIC driver default
ACPI: PM-Timer IO Port: 0x4008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 4, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
ACPI: IRQ9 used by override.
ACPI: IRQ14 used by override.
ACPI: IRQ15 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
ACPI: HPET id: 0x10de8201 base: 0xfeff0000
SMP: Allowing 4 CPUs, 2 hotplug CPUs
nr_irqs_gsi: 24
PM: Registered nosave memory: 000000000009c000 - 000000000009d000
PM: Registered nosave memory: 000000000009d000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
Allocating PCI resources starting at 7ff00000 (gap: 7ff00000:60100000)
NR_CPUS:4 nr_cpumask_bits:4 nr_cpu_ids:4 nr_node_ids:1
PERCPU: Embedded 11 pages/cpu @c3c00000 s23512 r0 d21544 u1048576
pcpu-alloc: s23512 r0 d21544 u1048576 alloc=1*4194304
pcpu-alloc: [0] 0 1 2 3
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 519806
Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.32testing root=/dev/mapper/nvidia_ceebaiib1 ro single
PID hash table entries: 4096 (order: 2, 16384 bytes)
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
Initializing HighMem for node 0 (000377fe:0007fef0)
Memory: 2052264k/2096064k available (2319k kernel code, 42160k reserved, 912k data, 404k init, 1186760k highmem)
virtual kernel memory layout:
fixmap : 0xfff6b000 - 0xfffff000 ( 592 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xf7ffe000 - 0xff7fe000 ( 120 MB)
lowmem : 0xc0000000 - 0xf77fe000 ( 887 MB)
.init : 0xc1329000 - 0xc138e000 ( 404 kB)
.data : 0xc1243e41 - 0xc1328128 ( 912 kB)
.text : 0xc1000000 - 0xc1243e41 (2319 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:384
Extended CMOS year: 2000
spurious 8259A interrupt: IRQ7.
Console: colour VGA+ 80x25
console [tty0] enabled
hpet clockevent registered
Fast TSC calibration using PIT
Detected 2133.576 MHz processor.
Calibrating delay loop (skipped), value calculated using timer frequency.. 4267.15 BogoMIPS (lpj=2133576)
Security Framework initialized
Mount-cache hash table entries: 512
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
mce: CPU supports 6 MCE banks
CPU0: Thermal monitoring enabled (TM2)
using mwait in idle threads.
Checking 'hlt' instruction... OK.
ACPI: Core revision 20090903
..TIMER: vector=0x30 apic1=0 pin1=0 apic2=-1 pin2=-1
..MP-BIOS bug: 8254 timer not connected to IO-APIC
...trying to set up timer (IRQ0) through the 8259A ...
..... (found apic 0 pin 0) ...
....... works.
CPU0: Intel(R) Core(TM)2 CPU 6400 @ 2.13GHz stepping 06
Booting processor 1 APIC 0x1 ip 0x6000
Initializing CPU#1
Calibrating delay using timer specific routine.. 4266.57 BogoMIPS (lpj=2133287)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU1: Thermal monitoring enabled (TM2)
CPU1: Intel(R) Core(TM)2 CPU 6400 @ 2.13GHz stepping 06
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Brought up 2 CPUs
Total of 2 processors activated (8533.72 BogoMIPS).
CPU0 attaching sched-domain:
domain 0: span 0-1 level MC
groups: 0 1
CPU1 attaching sched-domain:
domain 0: span 0-1 level MC
groups: 1 0
PM: Adding info for No Bus:platform
Time: 13:54:06 Date: 03/08/10
NET: Registered protocol family 16
PM: Adding info for No Bus:vtcon0
EISA bus registered
ACPI: bus type pci registered
PM: Adding info for No Bus:id
PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
PCI: MCFG area at e0000000 reserved in E820
PCI: Using MMCONFIG for extended config space
PCI: Using configuration type 1 for base access
PM: Adding info for No Bus:default
bio: create slab <bio-0> at 0
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
PM: Adding info for acpi:LNXSYSTM:00
PM: Adding info for acpi:LNXCPU:00
PM: Adding info for acpi:LNXCPU:01
PM: Adding info for acpi:LNXCPU:02
PM: Adding info for acpi:LNXCPU:03
PM: Adding info for acpi:LNXSYBUS:00
PM: Adding info for acpi:PNP0C0C:00
PM: Adding info for acpi:PNP0A08:00
PM: Adding info for acpi:PNP0C02:00
PM: Adding info for acpi:device:00
PM: Adding info for acpi:device:01
PM: Adding info for acpi:device:02
PM: Adding info for acpi:device:03
PM: Adding info for acpi:device:04
PM: Adding info for acpi:device:05
PM: Adding info for acpi:device:06
PM: Adding info for acpi:device:07
PM: Adding info for acpi:device:08
PM: Adding info for acpi:device:09
PM: Adding info for acpi:device:0a
PM: Adding info for acpi:device:0b
PM: Adding info for acpi:device:0c
PM: Adding info for acpi:device:0d
PM: Adding info for acpi:device:0e
PM: Adding info for acpi:device:0f
PM: Adding info for acpi:device:10
PM: Adding info for acpi:device:11
PM: Adding info for acpi:device:12
PM: Adding info for acpi:device:13
PM: Adding info for acpi:device:14
PM: Adding info for acpi:device:15
PM: Adding info for acpi:device:16
PM: Adding info for acpi:device:17
PM: Adding info for acpi:device:18
PM: Adding info for acpi:device:19
PM: Adding info for acpi:PNP0C02:01
PM: Adding info for acpi:PNP0000:00
PM: Adding info for acpi:PNP0200:00
PM: Adding info for acpi:PNP0100:00
PM: Adding info for acpi:PNP0103:00
PM: Adding info for acpi:PNP0B00:00
PM: Adding info for acpi:PNP0800:00
PM: Adding info for acpi:PNP0C04:00
PM: Adding info for acpi:device:1a
PM: Adding info for acpi:device:1b
PM: Adding info for acpi:device:1c
PM: Adding info for acpi:device:1d
PM: Adding info for acpi:device:1e
PM: Adding info for acpi:device:1f
PM: Adding info for acpi:NVRAIDBUS:00
PM: Adding info for acpi:ATK0110:00
PM: Adding info for acpi:PNP0C0F:00
PM: Adding info for acpi:PNP0C0F:01
PM: Adding info for acpi:PNP0C0F:02
PM: Adding info for acpi:PNP0C0F:03
PM: Adding info for acpi:PNP0C0F:04
PM: Adding info for acpi:PNP0C0F:05
PM: Adding info for acpi:PNP0C0F:06
PM: Adding info for acpi:PNP0C0F:07
PM: Adding info for acpi:PNP0C0F:08
PM: Adding info for acpi:PNP0C0F:09
PM: Adding info for acpi:PNP0C0F:0a
PM: Adding info for acpi:PNP0C0F:0b
PM: Adding info for acpi:PNP0C0F:0c
PM: Adding info for acpi:PNP0C0F:0d
PM: Adding info for acpi:PNP0C0F:0e
PM: Adding info for acpi:PNP0C0F:0f
PM: Adding info for acpi:PNP0C0F:10
PM: Adding info for acpi:PNP0C0F:11
PM: Adding info for acpi:PNP0C0F:12
PM: Adding info for acpi:PNP0C0F:13
PM: Adding info for acpi:PNP0C0F:14
PM: Adding info for acpi:PNP0C0F:15
PM: Adding info for acpi:PNP0C0F:16
PM: Adding info for acpi:PNP0C0F:17
PM: Adding info for acpi:PNP0C0F:18
PM: Adding info for acpi:PNP0C0F:19
PM: Adding info for acpi:PNP0C0F:1a
PM: Adding info for acpi:PNP0C0F:1b
PM: Adding info for acpi:PNP0C0F:1c
PM: Adding info for acpi:PNP0C0F:1d
PM: Adding info for acpi:PNP0C0F:1e
PM: Adding info for acpi:PNP0C0F:1f
PM: Adding info for acpi:PNP0C0F:20
PM: Adding info for acpi:PNP0C0F:21
PM: Adding info for acpi:PNP0C0F:22
PM: Adding info for acpi:PNP0C0F:23
PM: Adding info for acpi:PNP0C0F:24
PM: Adding info for acpi:PNP0C0F:25
PM: Adding info for acpi:PNP0C0F:26
PM: Adding info for acpi:PNP0C0F:27
PM: Adding info for acpi:PNP0C0F:28
PM: Adding info for acpi:PNP0C02:02
PM: Adding info for acpi:PNP0C01:00
PM: Adding info for acpi:LNXTHERM:00
PM: Adding info for acpi:PNP0C0B:00
PM: Adding info for acpi:LNXTHERM:01
PM: Adding info for acpi:LNXPWRBN:00
ACPI: No dock devices found.
ACPI: PCI Root Bridge [PCI0] (0000:00)
PM: Adding info for No Bus:pci0000:00
PM: Adding info for No Bus:0000:00
pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:02.0: PME# disabled
pci 0000:00:04.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:04.0: PME# disabled
pci 0000:00:05.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:05.0: PME# disabled
pci 0000:00:06.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:06.0: PME# disabled
pci 0000:00:07.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:07.0: PME# disabled
pci 0000:00:0a.1: reg 20 io port: [0x5000-0x503f]
pci 0000:00:0a.1: reg 24 io port: [0x5100-0x513f]
pci 0000:00:0a.1: PME# supported from D3hot D3cold
pci 0000:00:0a.1: PME# disabled
pci 0000:00:0b.0: reg 10 32bit mmio: [0xd5006000-0xd5006fff]
pci 0000:00:0b.0: supports D1 D2
pci 0000:00:0b.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:0b.0: PME# disabled
pci 0000:00:0b.1: reg 10 32bit mmio: [0xd5007000-0xd50070ff]
pci 0000:00:0b.1: supports D1 D2
pci 0000:00:0b.1: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:0b.1: PME# disabled
pci 0000:00:0d.0: reg 20 io port: [0xf000-0xf00f]
pci 0000:00:0e.0: reg 10 io port: [0x9f0-0x9f7]
pci 0000:00:0e.0: reg 14 io port: [0xbf0-0xbf3]
pci 0000:00:0e.0: reg 18 io port: [0x970-0x977]
pci 0000:00:0e.0: reg 1c io port: [0xb70-0xb73]
pci 0000:00:0e.0: reg 20 io port: [0xd400-0xd40f]
pci 0000:00:0e.0: reg 24 32bit mmio: [0xd5004000-0xd5004fff]
pci 0000:00:0f.0: reg 10 io port: [0x9e0-0x9e7]
pci 0000:00:0f.0: reg 14 io port: [0xbe0-0xbe3]
pci 0000:00:0f.0: reg 18 io port: [0x960-0x967]
pci 0000:00:0f.0: reg 1c io port: [0xb60-0xb63]
pci 0000:00:0f.0: reg 20 io port: [0xe800-0xe80f]
pci 0000:00:0f.0: reg 24 32bit mmio: [0xd5005000-0xd5005fff]
pci 0000:00:10.1: reg 10 32bit mmio: [0xd5000000-0xd5003fff]
pci 0000:00:10.1: PME# supported from D3hot D3cold
pci 0000:00:10.1: PME# disabled
pci 0000:01:00.0: reg 10 32bit mmio: [0xd0000000-0xd0ffffff]
pci 0000:01:00.0: reg 14 64bit mmio pref: [0xc0000000-0xcfffffff]
pci 0000:01:00.0: reg 1c 64bit mmio: [0xd1000000-0xd1ffffff]
pci 0000:01:00.0: reg 24 io port: [0xa000-0xa07f]
pci 0000:01:00.0: reg 30 32bit mmio pref: [0xd2000000-0xd201ffff]
pci 0000:00:02.0: bridge io port: [0xa000-0xafff]
pci 0000:00:02.0: bridge 32bit mmio: [0xd0000000-0xd2ffffff]
pci 0000:00:02.0: bridge 64bit mmio pref: [0xc0000000-0xcfffffff]
pci 0000:06:06.0: reg 10 32bit mmio: [0xd4001000-0xd40017ff]
pci 0000:06:06.0: reg 14 io port: [0xb000-0xb07f]
pci 0000:06:06.0: supports D2
pci 0000:06:06.0: PME# supported from D2 D3hot D3cold
pci 0000:06:06.0: PME# disabled
pci 0000:06:07.0: reg 10 io port: [0xb400-0xb4ff]
pci 0000:06:07.0: reg 14 32bit mmio: [0xd4000000-0xd40000ff]
pci 0000:06:07.0: reg 30 32bit mmio pref: [0xd3000000-0xd301ffff]
pci 0000:06:07.0: supports D1 D2
pci 0000:06:07.0: PME# supported from D1 D2 D3hot D3cold
pci 0000:06:07.0: PME# disabled
pci 0000:00:10.0: transparent bridge
pci 0000:00:10.0: bridge io port: [0xb000-0xbfff]
pci 0000:00:10.0: bridge 32bit mmio: [0xd3000000-0xd4ffffff]
pci_bus 0000:00: on NUMA node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
PM: Adding info for pci:0000:00:00.0
PM: Adding info for pci:0000:00:00.1
PM: Adding info for pci:0000:00:00.2
PM: Adding info for pci:0000:00:00.3
PM: Adding info for pci:0000:00:00.4
PM: Adding info for pci:0000:00:01.0
PM: Adding info for pci:0000:00:01.1
PM: Adding info for pci:0000:00:01.2
PM: Adding info for pci:0000:00:01.3
PM: Adding info for pci:0000:00:01.4
PM: Adding info for pci:0000:00:01.5
PM: Adding info for pci:0000:00:01.6
PM: Adding info for pci:0000:00:02.0
PM: Adding info for pci:0000:00:04.0
PM: Adding info for pci:0000:00:05.0
PM: Adding info for pci:0000:00:06.0
PM: Adding info for pci:0000:00:07.0
PM: Adding info for pci:0000:00:09.0
PM: Adding info for pci:0000:00:0a.0
PM: Adding info for pci:0000:00:0a.1
PM: Adding info for pci:0000:00:0a.2
PM: Adding info for pci:0000:00:0b.0
PM: Adding info for pci:0000:00:0b.1
PM: Adding info for pci:0000:00:0d.0
PM: Adding info for pci:0000:00:0e.0
PM: Adding info for pci:0000:00:0f.0
PM: Adding info for pci:0000:00:10.0
PM: Adding info for pci:0000:00:10.1
PM: Adding info for pci:0000:01:00.0
PM: Adding info for No Bus:0000:01
PM: Adding info for No Bus:0000:02
PM: Adding info for No Bus:0000:03
PM: Adding info for No Bus:0000:04
PM: Adding info for No Bus:0000:05
PM: Adding info for pci:0000:06:06.0
PM: Adding info for pci:0000:06:07.0
PM: Adding info for No Bus:0000:06
ACPI: PCI Interrupt Link [LNK1] (IRQs 5 7 9 *10 11 14 15)
ACPI: PCI Interrupt Link [LNK2] (IRQs *5 7 9 10 11 14 15)
ACPI: PCI Interrupt Link [LNK3] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK4] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK5] (IRQs 5 *7 9 10 11 14 15)
ACPI: PCI Interrupt Link [LNK6] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK7] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK8] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LUBA] (IRQs 5 *7 9 10 11 14 15)
ACPI: PCI Interrupt Link [LUBB] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LMAC] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LACI] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LAZA] (IRQs 5 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [LPMU] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LMCI] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSMB] (IRQs 5 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [LUB2] (IRQs *5 7 9 10 11 14 15)
ACPI: PCI Interrupt Link [LIDE] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSID] (IRQs 5 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [LFID] (IRQs 5 7 9 *10 11 14 15)
ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0
ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0
ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0, disabled.
ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled.
ACPI: PCI Interrupt Link [APC5] (IRQs 16) *0
ACPI: PCI Interrupt Link [APC6] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APC7] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APC8] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APMU] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [AAZA] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0
PM: Adding info for No Bus:vga_arbiter
vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
vgaarb: loaded
PCI: Using ACPI for IRQ routing
PM: Adding info for No Bus:lo
hpet0: at MMIO 0xfeff0000, IRQs 2, 8, 31
hpet0: 3 comparators, 32-bit 25.000000 MHz counter
Switching to clocksource tsc
pnp: PnP ACPI init
PM: Adding info for No Bus:pnp0
ACPI: bus type pnp registered
PM: Adding info for pnp:00:00
PM: Adding info for pnp:00:01
PM: Adding info for pnp:00:02
PM: Adding info for pnp:00:03
PM: Adding info for pnp:00:04
PM: Adding info for pnp:00:05
PM: Adding info for pnp:00:06
PM: Adding info for pnp:00:07
PM: Adding info for pnp:00:08
PM: Adding info for pnp:00:09
pnp: PnP ACPI: found 10 devices
ACPI: ACPI bus type pnp unregistered
PnPBIOS: Disabled by ACPI PNP
system 00:01: ioport range 0x4000-0x407f has been reserved
system 00:01: ioport range 0x4080-0x40ff has been reserved
system 00:01: ioport range 0x4400-0x447f has been reserved
system 00:01: ioport range 0x4480-0x44ff has been reserved
system 00:01: ioport range 0x4800-0x487f has been reserved
system 00:01: ioport range 0x4880-0x48ff has been reserved
system 00:02: ioport range 0x4d0-0x4d1 has been reserved
system 00:02: ioport range 0x800-0x87f has been reserved
system 00:02: ioport range 0x290-0x297 has been reserved
system 00:02: ioport range 0x880-0x88f has been reserved
system 00:08: iomem range 0xe0000000-0xefffffff has been reserved
system 00:09: iomem range 0xdbc00-0xdbfff has been reserved
system 00:09: iomem range 0xf0000-0xf7fff could not be reserved
system 00:09: iomem range 0xf8000-0xfbfff could not be reserved
system 00:09: iomem range 0xfc000-0xfffff could not be reserved
system 00:09: iomem range 0xfeff0000-0xfeff00ff has been reserved
system 00:09: iomem range 0x7fef0000-0x7fefffff could not be reserved
system 00:09: iomem range 0xffff0000-0xffffffff has been reserved
system 00:09: iomem range 0x0-0x9ffff could not be reserved
system 00:09: iomem range 0x100000-0x7feeffff could not be reserved
system 00:09: iomem range 0xfec00000-0xfec00fff could not be reserved
system 00:09: iomem range 0xfee00000-0xfee00fff has been reserved
system 00:09: iomem range 0xfeff0000-0xfeff03ff could not be reserved
PM: Adding info for No Bus:mem
PM: Adding info for No Bus:kmem
PM: Adding info for No Bus:null
PM: Adding info for No Bus:port
PM: Adding info for No Bus:zero
PM: Adding info for No Bus:full
PM: Adding info for No Bus:random
PM: Adding info for No Bus:urandom
PM: Adding info for No Bus:kmsg
pci 0000:06:07.0: BAR 6: address space collision on of device [0xd3000000-0xd301ffff]
pci 0000:00:02.0: PCI bridge, secondary bus 0000:01
pci 0000:00:02.0: IO window: 0xa000-0xafff
pci 0000:00:02.0: MEM window: 0xd0000000-0xd2ffffff
pci 0000:00:02.0: PREFETCH window: 0x000000c0000000-0x000000cfffffff
pci 0000:00:04.0: PCI bridge, secondary bus 0000:02
pci 0000:00:04.0: IO window: disabled
pci 0000:00:04.0: MEM window: disabled
pci 0000:00:04.0: PREFETCH window: disabled
pci 0000:00:05.0: PCI bridge, secondary bus 0000:03
pci 0000:00:05.0: IO window: disabled
pci 0000:00:05.0: MEM window: disabled
pci 0000:00:05.0: PREFETCH window: disabled
pci 0000:00:06.0: PCI bridge, secondary bus 0000:04
pci 0000:00:06.0: IO window: disabled
pci 0000:00:06.0: MEM window: disabled
pci 0000:00:06.0: PREFETCH window: disabled
pci 0000:00:07.0: PCI bridge, secondary bus 0000:05
pci 0000:00:07.0: IO window: disabled
pci 0000:00:07.0: MEM window: disabled
pci 0000:00:07.0: PREFETCH window: disabled
pci 0000:00:10.0: PCI bridge, secondary bus 0000:06
pci 0000:00:10.0: IO window: 0xb000-0xbfff
pci 0000:00:10.0: MEM window: 0xd3000000-0xd4ffffff
pci 0000:00:10.0: PREFETCH window: 0x80000000-0x800fffff
pci 0000:00:02.0: setting latency timer to 64
pci 0000:00:04.0: setting latency timer to 64
pci 0000:00:05.0: setting latency timer to 64
pci 0000:00:06.0: setting latency timer to 64
pci 0000:00:07.0: setting latency timer to 64
pci 0000:00:10.0: setting latency timer to 64
pci_bus 0000:00: resource 0 io: [0x00-0xffff]
pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
pci_bus 0000:01: resource 0 io: [0xa000-0xafff]
pci_bus 0000:01: resource 1 mem: [0xd0000000-0xd2ffffff]
pci_bus 0000:01: resource 2 pref mem [0xc0000000-0xcfffffff]
pci_bus 0000:06: resource 0 io: [0xb000-0xbfff]
pci_bus 0000:06: resource 1 mem: [0xd3000000-0xd4ffffff]
pci_bus 0000:06: resource 2 pref mem [0x80000000-0x800fffff]
pci_bus 0000:06: resource 3 io: [0x00-0xffff]
pci_bus 0000:06: resource 4 mem: [0x000000-0xffffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
pci 0000:01:00.0: Boot video device
Trying to unpack rootfs image as initramfs...
Freeing initrd memory: 20744k freed
PM: Adding info for No Bus:mcelog
PM: Adding info for No Bus:msr0
PM: Adding info for No Bus:msr1
PM: Adding info for platform:pcspkr
PM: Adding info for No Bus:snapshot
highmem bounce pool size: 64 pages
ROMFS MTD (C) 2007 Red Hat, Inc.
msgmni has been set to 1733
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
pcieport 0000:00:02.0: setting latency timer to 64
PM: Adding info for pci_express:0000:00:02.0:pcie08
pcieport 0000:00:04.0: setting latency timer to 64
PM: Adding info for pci_express:0000:00:04.0:pcie08
pcieport 0000:00:05.0: setting latency timer to 64
PM: Adding info for pci_express:0000:00:05.0:pcie08
pcieport 0000:00:06.0: setting latency timer to 64
PM: Adding info for pci_express:0000:00:06.0:pcie08
pcieport 0000:00:07.0: setting latency timer to 64
PM: Adding info for pci_express:0000:00:07.0:pcie08
PM: Adding info for No Bus:pnp1
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
PM: Adding info for No Bus:tty
PM: Adding info for No Bus:console
PM: Adding info for No Bus:tty0
PM: Adding info for No Bus:vcs
PM: Adding info for No Bus:vcsa
PM: Adding info for No Bus:vcs1
PM: Adding info for No Bus:vcsa1
PM: Adding info for No Bus:tty1
PM: Adding info for No Bus:tty2
PM: Adding info for No Bus:tty3
PM: Adding info for No Bus:tty4
PM: Adding info for No Bus:tty5
PM: Adding info for No Bus:tty6
PM: Adding info for No Bus:tty7
PM: Adding info for No Bus:tty8
PM: Adding info for No Bus:tty9
PM: Adding info for No Bus:tty10
PM: Adding info for No Bus:tty11
PM: Adding info for No Bus:tty12
PM: Adding info for No Bus:tty13
PM: Adding info for No Bus:tty14
PM: Adding info for No Bus:tty15
PM: Adding info for No Bus:tty16
PM: Adding info for No Bus:tty17
PM: Adding info for No Bus:tty18
PM: Adding info for No Bus:tty19
PM: Adding info for No Bus:tty20
PM: Adding info for No Bus:tty21
PM: Adding info for No Bus:tty22
PM: Adding info for No Bus:tty23
PM: Adding info for No Bus:tty24
PM: Adding info for No Bus:tty25
PM: Adding info for No Bus:tty26
PM: Adding info for No Bus:tty27
PM: Adding info for No Bus:tty28
PM: Adding info for No Bus:tty29
PM: Adding info for No Bus:tty30
PM: Adding info for No Bus:tty31
PM: Adding info for No Bus:tty32
PM: Adding info for No Bus:tty33
PM: Adding info for No Bus:tty34
PM: Adding info for No Bus:tty35
PM: Adding info for No Bus:tty36
PM: Adding info for No Bus:tty37
PM: Adding info for No Bus:tty38
PM: Adding info for No Bus:tty39
PM: Adding info for No Bus:tty40
PM: Adding info for No Bus:tty41
PM: Adding info for No Bus:tty42
PM: Adding info for No Bus:tty43
PM: Adding info for No Bus:tty44
PM: Adding info for No Bus:tty45
PM: Adding info for No Bus:tty46
PM: Adding info for No Bus:tty47
PM: Adding info for No Bus:tty48
PM: Adding info for No Bus:tty49
PM: Adding info for No Bus:tty50
PM: Adding info for No Bus:tty51
PM: Adding info for No Bus:tty52
PM: Adding info for No Bus:tty53
PM: Adding info for No Bus:tty54
PM: Adding info for No Bus:tty55
PM: Adding info for No Bus:tty56
PM: Adding info for No Bus:tty57
PM: Adding info for No Bus:tty58
PM: Adding info for No Bus:tty59
PM: Adding info for No Bus:tty60
PM: Adding info for No Bus:tty61
PM: Adding info for No Bus:tty62
PM: Adding info for No Bus:tty63
PM: Adding info for No Bus:ptmx
PM: Adding info for No Bus:hpet
PM: Adding info for No Bus:isa
PM: Adding info for No Bus:ram0
PM: Adding info for No Bus:1:0
PM: Adding info for No Bus:ram1
PM: Adding info for No Bus:1:1
PM: Adding info for No Bus:ram2
PM: Adding info for No Bus:1:2
PM: Adding info for No Bus:ram3
PM: Adding info for No Bus:1:3
PM: Adding info for No Bus:ram4
PM: Adding info for No Bus:1:4
PM: Adding info for No Bus:ram5
PM: Adding info for No Bus:1:5
PM: Adding info for No Bus:ram6
PM: Adding info for No Bus:1:6
PM: Adding info for No Bus:ram7
PM: Adding info for No Bus:1:7
PM: Adding info for No Bus:ram8
PM: Adding info for No Bus:1:8
PM: Adding info for No Bus:ram9
PM: Adding info for No Bus:1:9
PM: Adding info for No Bus:ram10
PM: Adding info for No Bus:1:10
PM: Adding info for No Bus:ram11
PM: Adding info for No Bus:1:11
PM: Adding info for No Bus:ram12
PM: Adding info for No Bus:1:12
PM: Adding info for No Bus:ram13
PM: Adding info for No Bus:1:13
PM: Adding info for No Bus:ram14
PM: Adding info for No Bus:1:14
PM: Adding info for No Bus:ram15
PM: Adding info for No Bus:1:15
brd: module loaded
PNP: No PS/2 controller found. Probing ports directly.
PM: Adding info for platform:i8042
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
PM: Adding info for serio:serio0
PM: Adding info for serio:serio1
PM: Adding info for No Bus:mice
PM: Adding info for No Bus:psaux
mice: PS/2 mouse device common for all mice
PM: Adding info for platform:eisa.0
EISA: Probing bus 0 at eisa.0
PM: Removing info for platform:eisa.0
cpuidle: using governor ladder
TCP cubic registered
Using IPI No-Shortcut mode
PM: Adding info for No Bus:cpu_dma_latency
PM: Adding info for No Bus:network_latency
PM: Adding info for No Bus:network_throughput
PM: Checking image partition /dev/hda6
PM: Resume from disk failed.
Magic number: 2:849:937
acpi PNP0103:00: hash matches
Freeing unused kernel memory: 404k freed
NET: Registered protocol family 1
PM: Adding info for No Bus:cooling_device0
fan PNP0C0B:00: registered as cooling_device0
ACPI: Fan [FAN] (on)
PM: Adding info for No Bus:thermal_zone0
thermal LNXTHERM:01: registered as thermal_zone0
ACPI: Thermal Zone [THRM] (40 C)
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17
r8169 0000:06:07.0: PCI INT A -> Link[APC2] -> GSI 17 (level, low) -> IRQ 17
r8169 0000:06:07.0: no PCI Express capability
PM: Adding info for No Bus:eth0
eth0: RTL8169sb/8110sb at 0xf871a000, 00:14:d1:1a:ac:15, XID 10000000 IRQ 17
SCSI subsystem initialized
Uniform Multi-Platform E-IDE driver
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci_hcd: block sizes: ed 64 td 64
ACPI: PCI Interrupt Link [APCF] enabled at IRQ 23
ohci_hcd 0000:00:0b.0: PCI INT A -> Link[APCF] -> GSI 23 (level, low) -> IRQ 23
ohci_hcd 0000:00:0b.0: setting latency timer to 64
ohci_hcd 0000:00:0b.0: OHCI Host Controller
drivers/usb/core/inode.c: creating file 'devices'
drivers/usb/core/inode.c: creating file '001'
ohci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:0b.0: created debug files
ohci_hcd 0000:00:0b.0: supports USB remote wakeup
ohci_hcd 0000:00:0b.0: irq 23, io mem 0xd5006000
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
udev: renamed network interface eth0 to eth1
Warning! ehci_hcd should always be loaded before uhci_hcd and ohci_hcd, not after
ehci_hcd: block sizes: qh 60 qtd 96 itd 160 sitd 96
ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16
ohci1394 0000:06:06.0: PCI INT A -> Link[APC1] -> GSI 16 (level, low) -> IRQ 16
PM: Adding info for ieee1394:fw-host0
PM: Adding info for No Bus:fw-host0
libata version 3.00 loaded.
ohci_hcd 0000:00:0b.0: OHCI controller state
ohci_hcd 0000:00:0b.0: OHCI 1.0, NO legacy support registers
ohci_hcd 0000:00:0b.0: control 0x683 RWE RWC HCFS=operational CBSR=3
ohci_hcd 0000:00:0b.0: cmdstatus 0x00000 SOC=0
ohci_hcd 0000:00:0b.0: intrstatus 0x00000044 RHSC SF
ohci_hcd 0000:00:0b.0: intrenable 0x8000000a MIE RD WDH
ohci_hcd 0000:00:0b.0: hcca frame #0003
ohci_hcd 0000:00:0b.0: roothub.a 01000208 POTPGT=1 NPS NDP=8(8)
ohci_hcd 0000:00:0b.0: roothub.b 00000000 PPCM=0000 DR=0000
ohci_hcd 0000:00:0b.0: roothub.status 00008000 DRWE
ohci_hcd 0000:00:0b.0: roothub.portstatus [0] 0x00010301 CSC LSDA PPS CCS
ohci_hcd 0000:00:0b.0: roothub.portstatus [1] 0x00010101 CSC PPS CCS
ohci_hcd 0000:00:0b.0: roothub.portstatus [2] 0x00010101 CSC PPS CCS
ohci_hcd 0000:00:0b.0: roothub.portstatus [3] 0x00000100 PPS
ohci_hcd 0000:00:0b.0: roothub.portstatus [4] 0x00000100 PPS
ohci_hcd 0000:00:0b.0: roothub.portstatus [5] 0x00010101 CSC PPS CCS
ohci_hcd 0000:00:0b.0: roothub.portstatus [6] 0x00000100 PPS
ohci_hcd 0000:00:0b.0: roothub.portstatus [7] 0x00000100 PPS
usb usb1: default language 0x0409
usb usb1: udev 1, busnum 1, minor = 0
usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: OHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.32testing ohci_hcd
usb usb1: SerialNumber: 0000:00:0b.0
PM: Adding info for usb:usb1
usb usb1: uevent
usb usb1: usb_probe_device
usb usb1: configuration #1 chosen from 1 choice
usb usb1: adding 1-0:1.0 (config #1, interface 0)
PM: Adding info for usb:1-0:1.0
usb 1-0:1.0: uevent
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: no power switching (usb 1.0)
hub 1-0:1.0: global over-current protection
hub 1-0:1.0: power on to power good time: 2ms
hub 1-0:1.0: local power source is good
hub 1-0:1.0: no over-current condition exists
hub 1-0:1.0: trying to enable port power on non-switchable hub
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev1.1
drivers/usb/core/inode.c: creating file '001'
PM: Adding info for No Bus:ep_00
ACPI: PCI Interrupt Link [APCL] enabled at IRQ 22
ehci_hcd 0000:00:0b.1: PCI INT B -> Link[APCL] -> GSI 22 (level, low) -> IRQ 22
ehci_hcd 0000:00:0b.1: setting latency timer to 64
ehci_hcd 0000:00:0b.1: EHCI Host Controller
drivers/usb/core/inode.c: creating file '002'
ehci_hcd 0000:00:0b.1: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:0b.1: reset hcs_params 0x101888 dbg=1 cc=1 pcc=8 !ppc ports=8
ehci_hcd 0000:00:0b.1: reset portroute 0 0 0 0 0 0 0 0
ehci_hcd 0000:00:0b.1: reset hcc_params a086 caching frame 256/512/1024 park
ehci_hcd 0000:00:0b.1: park 0
ehci_hcd 0000:00:0b.1: debug port 1
ehci_hcd 0000:00:0b.1: reset command 080b02 park=3 ithresh=8 period=1024 Reset HALT
ehci_hcd 0000:00:0b.1: cache line size of 32 is not supported
ehci_hcd 0000:00:0b.1: supports USB remote wakeup
ehci_hcd 0000:00:0b.1: irq 22, io mem 0xd5007000
ehci_hcd 0000:00:0b.1: reset command 080b02 park=3 ithresh=8 period=1024 Reset HALT
ehci_hcd 0000:00:0b.1: init command 010009 (park)=0 ithresh=1 period=256 RUN
usb usb1: uevent
usb usb1: uevent
ehci_hcd 0000:00:0b.1: USB 2.0 started, EHCI 1.00
usb usb2: default language 0x0409
usb usb2: udev 1, busnum 2, minor = 128
usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: EHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.32testing ehci_hcd
usb usb2: SerialNumber: 0000:00:0b.1
PM: Adding info for usb:usb2
usb usb2: uevent
usb usb2: usb_probe_device
usb usb2: configuration #1 chosen from 1 choice
usb usb2: adding 2-0:1.0 (config #1, interface 0)
PM: Adding info for usb:2-0:1.0
usb 2-0:1.0: uevent
hub 2-0:1.0: usb_probe_interface
hub 2-0:1.0: usb_probe_interface - got id
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 8 ports detected
hub 2-0:1.0: standalone hub
hub 2-0:1.0: no power switching (usb 1.0)
hub 2-0:1.0: individual port over-current protection
hub 2-0:1.0: power on to power good time: 20ms
hub 2-0:1.0: local power source is good
hub 2-0:1.0: trying to enable port power on non-switchable hub
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev2.1
drivers/usb/core/inode.c: creating file '001'
PM: Adding info for No Bus:ep_00
amd74xx 0000:00:0d.0: UDMA133 controller
amd74xx 0000:00:0d.0: IDE controller (0x10de:0x0265 rev 0xa1)
amd74xx 0000:00:0d.0: IDE port disabled
amd74xx 0000:00:0d.0: BIOS didn't set cable bits correctly. Enabling workaround.
amd74xx 0000:00:0d.0: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xf008-0xf00f
usb usb2: uevent
Probing IDE interface ide0...
usb usb2: uevent
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[16] MMIO=[d4001000-d40017ff] Max Packet=[2] IR/IT contexts=[4/8]
ohci1394: fw-host0: Serial EEPROM has suspicious values, attempting to set max_packet_size to 512 bytes
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00010300 CSC LSDA PPS
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [1] = 0x00010100 CSC PPS
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [2] = 0x00010100 CSC PPS
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [5] = 0x00010100 CSC PPS
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 2-0:1.0: port 1: status 0501 change 0001
ehci_hcd 0000:00:0b.1: GetStatus port 2 status 001803 POWER sig=j CSC CONNECT
hub 2-0:1.0: port 2: status 0501 change 0001
ehci_hcd 0000:00:0b.1: GetStatus port 3 status 001803 POWER sig=j CSC CONNECT
hub 2-0:1.0: port 3: status 0501 change 0001
ehci_hcd 0000:00:0b.1: GetStatus port 6 status 001803 POWER sig=j CSC CONNECT
hub 2-0:1.0: port 6: status 0501 change 0001
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0000
hub 2-0:1.0: state 7 ports 8 chg 004e evt 0000
hub 2-0:1.0: port 1, status 0501, change 0000, 480 Mb/s
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 2-0:1.0: port 2, status 0501, change 0000, 480 Mb/s
ehci_hcd 0000:00:0b.1: port 2 high speed
ehci_hcd 0000:00:0b.1: GetStatus port 2 status 001005 POWER sig=se0 PE CONNECT
usb 2-2: new high speed USB device using ehci_hcd and address 3
ehci_hcd 0000:00:0b.1: port 2 high speed
ehci_hcd 0000:00:0b.1: GetStatus port 2 status 001005 POWER sig=se0 PE CONNECT
usb 2-2: default language 0x0409
usb 2-2: udev 3, busnum 2, minor = 130
usb 2-2: New USB device found, idVendor=058f, idProduct=6362
usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-2: Product: Mass Storage Device
usb 2-2: Manufacturer: Generic
usb 2-2: SerialNumber: 058F312D81B
PM: Adding info for usb:2-2
usb 2-2: uevent
usb 2-2: usb_probe_device
usb 2-2: configuration #1 chosen from 1 choice
usb 2-2: adding 2-2:1.0 (config #1, interface 0)
PM: Adding info for usb:2-2:1.0
usb 2-2:1.0: uevent
PM: Adding info for No Bus:ep_01
PM: Adding info for No Bus:ep_82
PM: Adding info for No Bus:usbdev2.3
drivers/usb/core/inode.c: creating file '003'
PM: Adding info for No Bus:ep_00
hub 2-0:1.0: port 3, status 0501, change 0000, 480 Mb/s
usb 2-2: uevent
usb 2-2: uevent
Initializing USB Mass Storage driver...
usb-storage 2-2:1.0: usb_probe_interface
usb-storage 2-2:1.0: usb_probe_interface - got id
scsi0 : SCSI emulation for USB Mass Storage devices
PM: Adding info for scsi:host0
PM: Adding info for No Bus:host0
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
ehci_hcd 0000:00:0b.1: port 3 high speed
ehci_hcd 0000:00:0b.1: GetStatus port 3 status 001005 POWER sig=se0 PE CONNECT
usb 2-3: new high speed USB device using ehci_hcd and address 4
ehci_hcd 0000:00:0b.1: port 3 high speed
ehci_hcd 0000:00:0b.1: GetStatus port 3 status 001005 POWER sig=se0 PE CONNECT
hda: PIONEER DVD-RW DVR-111D, ATAPI CD/DVD-ROM drive
usb 2-3: default language 0x0409
usb 2-3: udev 4, busnum 2, minor = 131
usb 2-3: New USB device found, idVendor=05e3, idProduct=0605
usb 2-3: New USB device strings: Mfr=0, Product=1, SerialNumber=0
usb 2-3: Product: USB2.0 Hub
PM: Adding info for usb:2-3
usb 2-3: uevent
usb 2-3: usb_probe_device
usb 2-3: configuration #1 chosen from 1 choice
usb 2-3: adding 2-3:1.0 (config #1, interface 0)
PM: Adding info for usb:2-3:1.0
usb 2-3:1.0: uevent
hub 2-3:1.0: usb_probe_interface
hub 2-3:1.0: usb_probe_interface - got id
hub 2-3:1.0: USB hub found
hub 2-3:1.0: 4 ports detected
hub 2-3:1.0: standalone hub
hub 2-3:1.0: individual port power switching
hub 2-3:1.0: individual port over-current protection
hub 2-3:1.0: Single TT
hub 2-3:1.0: TT requires at most 32 FS bit times (2664 ns)
hub 2-3:1.0: Port indicators are supported
hub 2-3:1.0: power on to power good time: 100ms
usb 2-3: uevent
hub 2-3:1.0: local power source is good
hub 2-3:1.0: enabling power on all ports
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev2.4
drivers/usb/core/inode.c: creating file '004'
PM: Adding info for No Bus:ep_00
hub 2-0:1.0: port 6, status 0501, change 0000, 480 Mb/s
usb 2-3: uevent
ehci_hcd 0000:00:0b.1: port 6 high speed
ehci_hcd 0000:00:0b.1: GetStatus port 6 status 001005 POWER sig=se0 PE CONNECT
hub 2-3:1.0: port 1: status 0101 change 0001
usb 2-6: new high speed USB device using ehci_hcd and address 5
ehci_hcd 0000:00:0b.1: port 6 high speed
ehci_hcd 0000:00:0b.1: GetStatus port 6 status 001005 POWER sig=se0 PE CONNECT
usb 2-3: link qh256-0001/c210dec0 start 1 [1/0 us]
usb 2-6: udev 5, busnum 2, minor = 132
usb 2-6: New USB device found, idVendor=0409, idProduct=0059
usb 2-6: New USB device strings: Mfr=0, Product=0, SerialNumber=0
PM: Adding info for usb:2-6
usb 2-6: uevent
usb 2-6: usb_probe_device
usb 2-6: configuration #1 chosen from 1 choice
usb 2-6: adding 2-6:1.0 (config #1, interface 0)
PM: Adding info for usb:2-6:1.0
usb 2-6:1.0: uevent
hub 2-6:1.0: usb_probe_interface
hub 2-6:1.0: usb_probe_interface - got id
hub 2-6:1.0: USB hub found
hub 2-6:1.0: 4 ports detected
hub 2-6:1.0: standalone hub
hub 2-6:1.0: individual port power switching
hub 2-6:1.0: individual port over-current protection
hub 2-6:1.0: Single TT
hub 2-6:1.0: TT requires at most 16 FS bit times (1332 ns)
hub 2-6:1.0: Port indicators are supported
hub 2-6:1.0: power on to power good time: 100ms
usb 2-6: uevent
hub 2-6:1.0: local power source is good
hub 2-6:1.0: enabling power on all ports
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev2.5
usb 2-6: uevent
drivers/usb/core/inode.c: creating file '005'
PM: Adding info for No Bus:ep_00
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00010301 CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0001, 1.5 Mb/s
hub 2-6:1.0: port 1: status 0301 change 0001
hub 2-6:1.0: port 3: status 0101 change 0001
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130301 PRSC PESC CSC LSDA PPS CCS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-3:1.0: state 7 ports 4 chg 0002 evt 0000
hub 2-3:1.0: port 1, status 0101, change 0000, 12 Mb/s
usb 2-6: link qh256-0001/c1cabd40 start 2 [1/0 us]
usb 2-3.1: new high speed USB device using ehci_hcd and address 6
usb 2-3.1: udev 6, busnum 2, minor = 133
usb 2-3.1: New USB device found, idVendor=0409, idProduct=0059
usb 2-3.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
PM: Adding info for usb:2-3.1
usb 2-3.1: uevent
usb 2-3.1: usb_probe_device
usb 2-3.1: configuration #1 chosen from 1 choice
usb 2-3.1: adding 2-3.1:1.0 (config #1, interface 0)
PM: Adding info for usb:2-3.1:1.0
usb 2-3.1:1.0: uevent
hub 2-3.1:1.0: usb_probe_interface
hub 2-3.1:1.0: usb_probe_interface - got id
hub 2-3.1:1.0: USB hub found
hub 2-3.1:1.0: 4 ports detected
hub 2-3.1:1.0: standalone hub
hub 2-3.1:1.0: individual port power switching
hub 2-3.1:1.0: individual port over-current protection
hub 2-3.1:1.0: Single TT
hub 2-3.1:1.0: TT requires at most 16 FS bit times (1332 ns)
hub 2-3.1:1.0: Port indicators are supported
hub 2-3.1:1.0: power on to power good time: 100ms
hub 2-3.1:1.0: local power source is good
hub 2-3.1:1.0: enabling power on all ports
usb 2-3.1: uevent
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev2.6
drivers/usb/core/inode.c: creating file '006'
PM: Adding info for No Bus:ep_00
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
usb 2-3.1: uevent
PM: Adding info for ieee1394:001106000000bd66
PM: Adding info for No Bus:001106000000bd66
ieee1394: Host added: ID:BUS[0-00:1023] GUID[001106000000bd66]
PM: Adding info for No Bus:ide0
PM: Adding info for No Bus:ide0
hda: host max PIO5 wanted PIO255(auto-tune) selected PIO4
hda: UDMA/66 mode selected
ide0 at 0x170-0x177,0x376 on irq 15
PM: Adding info for ieee1394:001a66fffee31809
PM: Adding info for No Bus:001a66fffee31809
ieee1394: Node added: ID:BUS[0-01:1023] GUID[001a66fffee31809]
PM: Adding info for ieee1394:001a66fffee31809-0
PM: Adding info for No Bus:001a66fffee31809-0
PM: Adding info for ieee1394:001a66fffee31809-1
PM: Adding info for No Bus:001a66fffee31809-1
PM: Adding info for ide:0.0
sata_nv 0000:00:0e.0: version 3.5
ACPI: PCI Interrupt Link [APSI] enabled at IRQ 21
sata_nv 0000:00:0e.0: PCI INT A -> Link[APSI] -> GSI 21 (level, low) -> IRQ 21
sata_nv 0000:00:0e.0: Using SWNCQ mode
sata_nv 0000:00:0e.0: setting latency timer to 64
scsi1 : sata_nv
PM: Adding info for scsi:host1
PM: Adding info for No Bus:host1
scsi2 : sata_nv
PM: Adding info for scsi:host2
PM: Adding info for No Bus:host2
ata1: SATA max UDMA/133 cmd 0x9f0 ctl 0xbf0 bmdma 0xd400 irq 21
ata2: SATA max UDMA/133 cmd 0x970 ctl 0xb70 bmdma 0xd408 irq 21
ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 20
sata_nv 0000:00:0f.0: PCI INT A -> Link[APSJ] -> GSI 20 (level, low) -> IRQ 20
sata_nv 0000:00:0f.0: Using SWNCQ mode
sata_nv 0000:00:0f.0: setting latency timer to 64
scsi3 : sata_nv
PM: Adding info for scsi:host3
PM: Adding info for No Bus:host3
scsi4 : sata_nv
PM: Adding info for scsi:host4
PM: Adding info for No Bus:host4
ata3: SATA max UDMA/133 cmd 0x9e0 ctl 0xbe0 bmdma 0xe800 irq 20
ata4: SATA max UDMA/133 cmd 0x960 ctl 0xb60 bmdma 0xe808 irq 20
hub 2-3.1:1.0: port 1: status 0301 change 0001
hub 2-3.1:1.0: port 2: status 0101 change 0001
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-6:1.0: state 7 ports 4 chg 000a evt 0000
hub 2-6:1.0: port 1, status 0301, change 0000, 1.5 Mb/s
hub 2-6:1.0: port 1 not reset yet, waiting 10ms
usb 2-3.1: link qh256-0001/c1e4a5c0 start 3 [1/0 us]
usb 2-6.1: new low speed USB device using ehci_hcd and address 7
hub 2-6:1.0: port 1 not reset yet, waiting 10ms
usb 2-6.1: skipped 1 descriptor after interface
usb 2-6.1: default language 0x0409
usb 2-6.1: udev 7, busnum 2, minor = 134
usb 2-6.1: New USB device found, idVendor=2222, idProduct=3100
usb 2-6.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 2-6.1: Product: Macally ECOMouse
usb 2-6.1: Manufacturer: Macally Peripherals
PM: Adding info for usb:2-6.1
usb 2-6.1: uevent
usb 2-6.1: usb_probe_device
usb 2-6.1: configuration #1 chosen from 1 choice
usb 2-6.1: adding 2-6.1:1.0 (config #1, interface 0)
PM: Adding info for usb:2-6.1:1.0
usb 2-6.1:1.0: uevent
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev2.7
drivers/usb/core/inode.c: creating file '007'
PM: Adding info for No Bus:ep_00
hub 2-6:1.0: port 3, status 0101, change 0000, 12 Mb/s
usb 2-6.1: uevent
usb 2-6.1: uevent
usbcore: registered new interface driver hiddev
usbhid 2-6.1:1.0: usb_probe_interface
usbhid 2-6.1:1.0: usb_probe_interface - got id
PM: Adding info for hid:0003:2222:3100.0001
PM: Adding info for No Bus:input0
input: Macally Peripherals Macally ECOMouse as /devices/pci0000:00/0000:00:0b.1/usb2/2-6/2-6.1/2-6.1:1.0/input/input0
PM: Adding info for No Bus:mouse0
generic-usb 0003:2222:3100.0001: input: USB HID v1.00 Mouse [Macally Peripherals Macally ECOMouse ] on usb-0000:00:0b.1-6.1/input0
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
hub 2-6:1.0: port 3 not reset yet, waiting 10ms
ata3: SATA link down (SStatus 0 SControl 300)
usb 2-6.3: new full speed USB device using ehci_hcd and address 8
hub 2-6:1.0: port 3 not reset yet, waiting 10ms
usb 2-6.3: ep0 maxpacket = 8
usb 2-6.3: default language 0x0409
usb 2-6.3: udev 8, busnum 2, minor = 135
usb 2-6.3: New USB device found, idVendor=05e3, idProduct=0604
usb 2-6.3: New USB device strings: Mfr=0, Product=1, SerialNumber=0
usb 2-6.3: Product: USB Hub
PM: Adding info for usb:2-6.3
usb 2-6.3: uevent
usb 2-6.3: usb_probe_device
usb 2-6.3: configuration #1 chosen from 1 choice
usb 2-6.3: adding 2-6.3:1.0 (config #1, interface 0)
PM: Adding info for usb:2-6.3:1.0
usb 2-6.3:1.0: uevent
hub 2-6.3:1.0: usb_probe_interface
hub 2-6.3:1.0: usb_probe_interface - got id
hub 2-6.3:1.0: USB hub found
usb 2-6.3: uevent
hub 2-6.3:1.0: 4 ports detected
hub 2-6.3:1.0: standalone hub
hub 2-6.3:1.0: individual port power switching
hub 2-6.3:1.0: individual port over-current protection
hub 2-6.3:1.0: power on to power good time: 100ms
hub 2-6.3:1.0: local power source is good
hub 2-6.3:1.0: enabling power on all ports
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev2.8
drivers/usb/core/inode.c: creating file '008'
PM: Adding info for No Bus:ep_00
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030300 PESC CSC LSDA PPS
hub 1-0:1.0: port 1, status 0300, change 0003, 1.5 Mb/s
usb 2-6.3: uevent
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
hub 2-6.3:1.0: port 3: status 0301 change 0001
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x300
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 2-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
ata1.00: ATA-7: SAMSUNG SP2504C, VT100-41, max UDMA7
ata1.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata1.00: configured for UDMA/133
scsi 1:0:0:0: Direct-Access ATA SAMSUNG SP2504C VT10 PQ: 0 ANSI: 5
PM: Adding info for scsi:target1:0:0
PM: Adding info for scsi:1:0:0:0
PM: Adding info for No Bus:1:0:0:0
PM: Adding info for No Bus:1:0:0:0
usb 2-6.3: link qh128-0e01/c1e81140 start 4 [1/2 us]
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 2-3.1:1.0: state 7 ports 4 chg 0006 evt 0000
hub 2-3.1:1.0: port 1, status 0301, change 0000, 1.5 Mb/s
hub 2-3.1:1.0: port 1 not reset yet, waiting 10ms
usb 2-3.1.1: new low speed USB device using ehci_hcd and address 10
hub 2-3.1:1.0: port 1 not reset yet, waiting 10ms
usb 2-3.1.1: skipped 1 descriptor after interface
usb 2-3.1.1: skipped 1 descriptor after interface
usb 2-3.1.1: default language 0x0409
usb 2-3.1.1: udev 10, busnum 2, minor = 137
usb 2-3.1.1: New USB device found, idVendor=10d5, idProduct=0004
usb 2-3.1.1: New USB device strings: Mfr=0, Product=2, SerialNumber=0
usb 2-3.1.1: Product: PS2 to USB AdapterA3
PM: Adding info for usb:2-3.1.1
usb 2-3.1.1: uevent
usb 2-3.1.1: usb_probe_device
usb 2-3.1.1: configuration #1 chosen from 1 choice
usb 2-3.1.1: uevent
usb 2-3.1.1: adding 2-3.1.1:1.0 (config #1, interface 0)
PM: Adding info for usb:2-3.1.1:1.0
usb 2-3.1.1:1.0: uevent
usbhid 2-3.1.1:1.0: usb_probe_interface
usbhid 2-3.1.1:1.0: usb_probe_interface - got id
PM: Adding info for hid:0003:10D5:0004.0002
PM: Adding info for No Bus:input1
input: PS2 to USB AdapterA3 as /devices/pci0000:00/0000:00:0b.1/usb2/2-3/2-3.1/2-3.1.1/2-3.1.1:1.0/input/input1
usb 2-3.1.1: link qh8-0e01/c1e81440 start 5 [1/2 us]
generic-usb 0003:10D5:0004.0002: input: USB HID v1.10 Keyboard [PS2 to USB AdapterA3] on usb-0000:00:0b.1-3.1.1/input0
PM: Adding info for No Bus:ep_81
usb 2-3.1.1: adding 2-3.1.1:1.1 (config #1, interface 1)
PM: Adding info for usb:2-3.1.1:1.1
usb 2-3.1.1:1.1: uevent
usbhid 2-3.1.1:1.1: usb_probe_interface
usbhid 2-3.1.1:1.1: usb_probe_interface - got id
PM: Adding info for hid:0003:10D5:0004.0003
PM: Adding info for No Bus:input2
input: PS2 to USB AdapterA3 as /devices/pci0000:00/0000:00:0b.1/usb2/2-3/2-3.1/2-3.1.1/2-3.1.1:1.1/input/input2
usb 2-3.1.1: link qh8-0e01/c1e81540 start 6 [1/2 us]
PM: Adding info for No Bus:mouse1
generic-usb 0003:10D5:0004.0003: input: USB HID v1.10 Mouse [PS2 to USB AdapterA3] on usb-0000:00:0b.1-3.1.1/input1
PM: Adding info for No Bus:ep_82
PM: Adding info for No Bus:usbdev2.10
drivers/usb/core/inode.c: creating file '010'
PM: Adding info for No Bus:ep_00
usb 2-3.1.1: uevent
hub 2-3.1:1.0: port 2, status 0101, change 0000, 12 Mb/s
hub 2-3.1:1.0: port 2 not reset yet, waiting 10ms
usb 2-3.1.2: new high speed USB device using ehci_hcd and address 11
hub 2-3.1:1.0: port 2 not reset yet, waiting 10ms
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
usb 2-3.1.2: default language 0x0409
usb 2-3.1.2: udev 11, busnum 2, minor = 138
usb 2-3.1.2: New USB device found, idVendor=05e3, idProduct=0605
usb 2-3.1.2: New USB device strings: Mfr=0, Product=1, SerialNumber=0
usb 2-3.1.2: Product: USB2.0 Hub
PM: Adding info for usb:2-3.1.2
usb 2-3.1.2: uevent
usb 2-3.1.2: usb_probe_device
usb 2-3.1.2: configuration #1 chosen from 1 choice
usb 2-3.1.2: adding 2-3.1.2:1.0 (config #1, interface 0)
PM: Adding info for usb:2-3.1.2:1.0
usb 2-3.1.2:1.0: uevent
hub 2-3.1.2:1.0: usb_probe_interface
hub 2-3.1.2:1.0: usb_probe_interface - got id
hub 2-3.1.2:1.0: USB hub found
hub 2-3.1.2:1.0: 4 ports detected
hub 2-3.1.2:1.0: standalone hub
hub 2-3.1.2:1.0: individual port power switching
hub 2-3.1.2:1.0: individual port over-current protection
hub 2-3.1.2:1.0: Single TT
hub 2-3.1.2:1.0: TT requires at most 32 FS bit times (2664 ns)
hub 2-3.1.2:1.0: Port indicators are supported
hub 2-3.1.2:1.0: power on to power good time: 100ms
usb 2-3.1.2: uevent
hub 2-3.1.2:1.0: local power source is good
hub 2-3.1.2:1.0: enabling power on all ports
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev2.11
drivers/usb/core/inode.c: creating file '011'
PM: Adding info for No Bus:ep_00
hub 2-6:1.0: state 7 ports 4 chg 0000 evt 0002
usb 2-3.1.2: uevent
hub 2-6.3:1.0: state 7 ports 4 chg 0008 evt 0000
hub 2-6.3:1.0: port 3, status 0301, change 0000, 1.5 Mb/s
ata2.00: ATA-7: ST3250620AS, 3.AAC, max UDMA/133
ata2.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32)
usb 2-6.3.3: new low speed USB device using ehci_hcd and address 12
hub 2-6.3:1.0: port 3 not reset yet, waiting 10ms
hub 2-3.1.2:1.0: port 1: status 0101 change 0001
hub 2-3.1.2:1.0: port 2: status 0301 change 0001
ata2.00: configured for UDMA/133
scsi 2:0:0:0: Direct-Access ATA ST3250620AS 3.AA PQ: 0 ANSI: 5
PM: Adding info for scsi:target2:0:0
PM: Adding info for scsi:2:0:0:0
PM: Adding info for No Bus:2:0:0:0
PM: Adding info for No Bus:2:0:0:0
usb 2-6.3.3: skipped 1 descriptor after interface
usb 2-6.3.3: skipped 1 descriptor after interface
usb 2-6.3.3: default language 0x0409
usb 2-6.3.3: udev 12, busnum 2, minor = 139
usb 2-6.3.3: New USB device found, idVendor=2222, idProduct=0013
usb 2-6.3.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 2-6.3.3: Product: Macally iKeySlim
usb 2-6.3.3: Manufacturer: Macally Peripherals
PM: Adding info for usb:2-6.3.3
usb 2-6.3.3: uevent
usb 2-6.3.3: usb_probe_device
usb 2-6.3.3: configuration #1 chosen from 1 choice
usb 2-6.3.3: uevent
usb 2-6.3.3: adding 2-6.3.3:1.0 (config #1, interface 0)
PM: Adding info for usb:2-6.3.3:1.0
usb 2-6.3.3:1.0: uevent
usbhid 2-6.3.3:1.0: usb_probe_interface
usbhid 2-6.3.3:1.0: usb_probe_interface - got id
PM: Adding info for hid:0003:2222:0013.0004
PM: Adding info for No Bus:input3
input: Macally Peripherals Macally iKeySlim as /devices/pci0000:00/0000:00:0b.1/usb2/2-6/2-6.3/2-6.3.3/2-6.3.3:1.0/input/input3
usb 2-6.3.3: link qh8-0e01/c1e81a00 start 7 [1/2 us]
generic-usb 0003:2222:0013.0004: input: USB HID v1.10 Keyboard [Macally Peripherals Macally iKeySlim] on usb-0000:00:0b.1-6.3.3/input0
PM: Adding info for No Bus:ep_81
usb 2-6.3.3: adding 2-6.3.3:1.1 (config #1, interface 1)
PM: Adding info for usb:2-6.3.3:1.1
usb 2-6.3.3:1.1: uevent
usbhid 2-6.3.3:1.1: usb_probe_interface
usbhid 2-6.3.3:1.1: usb_probe_interface - got id
PM: Adding info for hid:0003:2222:0013.0005
PM: Adding info for No Bus:input4
input: Macally Peripherals Macally iKeySlim as /devices/pci0000:00/0000:00:0b.1/usb2/2-6/2-6.3/2-6.3.3/2-6.3.3:1.1/input/input4
usb 2-6.3.3: link qh8-0e01/c1e81b40 start 0 [1/2 us]
PM: Adding info for No Bus:mouse2
generic-usb 0003:2222:0013.0005: input: USB HID v1.10 Mouse [Macally Peripherals Macally iKeySlim] on usb-0000:00:0b.1-6.3.3/input1
PM: Adding info for No Bus:ep_82
PM: Adding info for No Bus:usbdev2.12
drivers/usb/core/inode.c: creating file '012'
PM: Adding info for No Bus:ep_00
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00010301 CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0001, 1.5 Mb/s
usb 2-6.3.3: uevent
usb 2-3.1.2: link qh256-0001/c1e81bc0 start 9 [1/0 us]
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-3.1:1.0: state 7 ports 4 chg 0000 evt 0004
hub 2-6.3:1.0: state 7 ports 4 chg 0000 evt 0008
hub 2-3.1.2:1.0: state 7 ports 4 chg 0006 evt 0000
hub 2-3.1.2:1.0: port 1, status 0101, change 0000, 12 Mb/s
usb 2-3.1.2.1: new high speed USB device using ehci_hcd and address 13
hub 2-3.1.2:1.0: port 1 not reset yet, waiting 10ms
usb 2-3.1.2.1: default language 0x0409
usb 2-3.1.2.1: udev 13, busnum 2, minor = 140
usb 2-3.1.2.1: New USB device found, idVendor=090c, idProduct=1000
usb 2-3.1.2.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-3.1.2.1: Product: DISK 2.0
usb 2-3.1.2.1: Manufacturer: USB
usb 2-3.1.2.1: SerialNumber: PHN84K6AD8PLXSVC
PM: Adding info for usb:2-3.1.2.1
usb 2-3.1.2.1: uevent
usb 2-3.1.2.1: usb_probe_device
usb 2-3.1.2.1: configuration #1 chosen from 1 choice
usb 2-3.1.2.1: adding 2-3.1.2.1:1.0 (config #1, interface 0)
PM: Adding info for usb:2-3.1.2.1:1.0
usb 2-3.1.2.1:1.0: uevent
usb-storage 2-3.1.2.1:1.0: usb_probe_interface
usb-storage 2-3.1.2.1:1.0: usb_probe_interface - got id
scsi5 : SCSI emulation for USB Mass Storage devices
PM: Adding info for scsi:host5
PM: Adding info for No Bus:host5
usb-storage: device found at 13
usb-storage: waiting for device to settle before scanning
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:ep_02
PM: Adding info for No Bus:usbdev2.13
drivers/usb/core/inode.c: creating file '013'
PM: Adding info for No Bus:ep_00
usb 2-3.1.2.1: uevent
usb 2-3.1.2.1: uevent
hub 2-3.1.2:1.0: port 2, status 0301, change 0000, 1.5 Mb/s
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: ATAPI: ATAPI iHOS104, WL08, max UDMA/100
usb 2-3.1.2.2: new low speed USB device using ehci_hcd and address 14
ata4.00: configured for UDMA/100
hub 2-3.1.2:1.0: port 2 not reset yet, waiting 10ms
scsi 4:0:0:0: CD-ROM ATAPI iHOS104 WL08 PQ: 0 ANSI: 5
PM: Adding info for scsi:target4:0:0
PM: Adding info for scsi:4:0:0:0
PM: Adding info for No Bus:4:0:0:0
PM: Adding info for No Bus:4:0:0:0
PM: Adding info for No Bus:1:0:0:0
sd 1:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
PM: Adding info for No Bus:sda
sda:
PM: Adding info for No Bus:2:0:0:0
sd 2:0:0:0: [sdb] 488397168 512-byte logical blocks: (250 GB/232 GiB)
sd 2:0:0:0: [sdb] Write Protect is off
sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
PM: Adding info for No Bus:sdb
sdb: sda1 sda2 sda3 < >
PM: Adding info for No Bus:sda1
PM: Adding info for No Bus:sda2
PM: Adding info for No Bus:sda3
PM: Adding info for No Bus:8:0
unknown partition table
PM: Adding info for No Bus:8:16
sd 2:0:0:0: [sdb] Attached SCSI disk
sd 1:0:0:0: [sda] Attached SCSI disk
ide-cd driver 5.00
PM: Adding info for No Bus:0.0
ide-cd: hda: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2000kB Cache
Uniform CD-ROM driver Revision: 3.20
usb 2-3.1.2.2: skipped 1 descriptor after interface
usb 2-3.1.2.2: default language 0x0409
usb 2-3.1.2.2: udev 14, busnum 2, minor = 141
usb 2-3.1.2.2: New USB device found, idVendor=046d, idProduct=c050
usb 2-3.1.2.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 2-3.1.2.2: Product: USB-PS/2 Optical Mouse
usb 2-3.1.2.2: Manufacturer: Logitech
PM: Adding info for usb:2-3.1.2.2
usb 2-3.1.2.2: uevent
usb 2-3.1.2.2: usb_probe_device
usb 2-3.1.2.2: configuration #1 chosen from 1 choice
usb 2-3.1.2.2: adding 2-3.1.2.2:1.0 (config #1, interface 0)
PM: Adding info for usb:2-3.1.2.2:1.0
usb 2-3.1.2.2:1.0: uevent
usbhid 2-3.1.2.2:1.0: usb_probe_interface
usbhid 2-3.1.2.2:1.0: usb_probe_interface - got id
PM: Adding info for hid:0003:046D:C050.0006
usb 2-3.1.2.2: uevent
PM: Adding info for No Bus:input5
input: Logitech USB-PS/2 Optical Mouse as /devices/pci0000:00/0000:00:0b.1/usb2/2-3/2-3.1/2-3.1.2/2-3.1.2.2/2-3.1.2.2:1.0/input/input5
PM: Adding info for No Bus:mouse3
generic-usb 0003:046D:C050.0006: input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:0b.1-3.1.2.2/input0
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev2.14
drivers/usb/core/inode.c: creating file '014'
PM: Adding info for No Bus:ep_00
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 2-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
usb 2-3.1.2.2: uevent
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
PM: Adding info for No Bus:device-mapper
device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
PM: Adding info for No Bus:dm-0
PM: Adding info for No Bus:254:0
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
PM: Adding info for No Bus:dm-1
PM: Adding info for No Bus:254:1
PM: Adding info for No Bus:dm-2
PM: Adding info for No Bus:254:2
PM: Adding info for No Bus:dm-3
PM: Adding info for No Bus:254:3
PM: Adding info for No Bus:dm-4
PM: Adding info for No Bus:254:4
PM: Adding info for No Bus:dm-5
PM: Adding info for No Bus:254:5
PM: Adding info for No Bus:dm-6
PM: Adding info for No Bus:254:6
PM: Removing info for No Bus:254:3
PM: Removing info for No Bus:dm-3
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 2-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
PM: Adding info for No Bus:hda
PM: Adding info for No Bus:3:0
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
xor: automatically using best checksumming function: pIII_sse
pIII_sse : 7516.000 MB/sec
xor: using function: pIII_sse (7516.000 MB/sec)
raid6: int32x1 878 MB/s
raid6: int32x2 839 MB/s
raid6: int32x4 703 MB/s
raid6: int32x8 585 MB/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
raid6: mmxx1 2742 MB/s
raid6: mmxx2 3167 MB/s
raid6: sse1x1 1890 MB/s
raid6: sse1x2 2441 MB/s
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 2-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
raid6: sse2x1 3542 MB/s
raid6: sse2x2 4226 MB/s
raid6: using algorithm sse2x2 (4226 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
md: raid10 personality registered for level 10
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
PM: Marking nosave pages: 000000000009c000 - 0000000000100000
PM: Basic memory bitmaps created
PM: Basic memory bitmaps freed
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with writeback data mode.
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 2-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 2-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 2-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 2-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 2-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
scsi 0:0:0:0: Direct-Access Generic USB SD Reader 1.00 PQ: 0 ANSI: 0
PM: Adding info for scsi:target0:0:0
PM: Adding info for scsi:0:0:0:0
PM: Adding info for No Bus:0:0:0:0
PM: Adding info for No Bus:0:0:0:0
PM: Adding info for No Bus:0:0:0:0
scsi 0:0:0:1: Direct-Access Generic USB CF Reader 1.01 PQ: 0 ANSI: 0
PM: Adding info for scsi:0:0:0:1
PM: Adding info for No Bus:0:0:0:1
PM: Adding info for No Bus:0:0:0:1
PM: Adding info for No Bus:0:0:0:1
PM: Adding info for No Bus:sdc
PM: Adding info for No Bus:8:32
PM: Adding info for No Bus:sdd
PM: Adding info for No Bus:8:48
scsi 0:0:0:2: Direct-Access Generic USB SM Reader 1.02 PQ: 0 ANSI: 0
PM: Adding info for scsi:0:0:0:2
PM: Adding info for No Bus:0:0:0:2
PM: Adding info for No Bus:0:0:0:2
PM: Adding info for No Bus:0:0:0:2
sd 0:0:0:0: [sdc] Attached SCSI removable disk
sd 0:0:0:1: [sdd] Attached SCSI removable disk
PM: Adding info for No Bus:sde
PM: Adding info for No Bus:8:64
scsi 0:0:0:3: Direct-Access Generic USB MS Reader 1.03 PQ: 0 ANSI: 0
PM: Adding info for scsi:0:0:0:3
PM: Adding info for No Bus:0:0:0:3
PM: Adding info for No Bus:0:0:0:3
PM: Adding info for No Bus:0:0:0:3
sd 0:0:0:2: [sde] Attached SCSI removable disk
PM: Adding info for No Bus:sdf
PM: Adding info for No Bus:8:80
sd 0:0:0:3: [sdf] Attached SCSI removable disk
usb-storage: device scan complete
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 2-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 2-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 2-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
udev: starting version 146
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
usb usb1: uevent
usb 1-0:1.0: uevent
usb usb2: uevent
usb 2-0:1.0: uevent
usb 2-2: uevent
usb 2-2:1.0: uevent
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
usb 2-3: uevent
usb 2-3.1: uevent
usb 2-3.1.1: uevent
usb 2-3.1.1:1.0: uevent
usb 2-3.1.1:1.1: uevent
usb 2-3.1.2: uevent
usb 2-3.1.2.1: uevent
usb 2-3.1.2.1:1.0: uevent
usb 2-3.1.2.2: uevent
usb 2-3.1.2.2:1.0: uevent
usb 2-3.1.2:1.0: uevent
usb 2-3.1:1.0: uevent
usb 2-3:1.0: uevent
usb 2-6: uevent
usb 2-6.1: uevent
usb 2-6.1:1.0: uevent
usb 2-6.3: uevent
usb 2-6.3.3: uevent
usb 2-6.3.3:1.0: uevent
usb 2-6.3.3:1.1: uevent
usb 2-6.3:1.0: uevent
usb 2-6:1.0: uevent
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 2-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
usb usb2: uevent
usb usb1: uevent
usb usb2: uevent
usb usb1: uevent
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
usb 2-2: uevent
usb 2-3: uevent
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
usb 2-6: uevent
usb 2-3: uevent
usb 2-2:1.0: uevent
usb 2-2: uevent
usb 2-2:1.0: uevent
usb 2-2: uevent
usb 2-2:1.0: uevent
usb 2-2: uevent
usb 2-2: uevent
usb 2-2:1.0: uevent
usb 2-2: uevent
usb 2-6: uevent
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 2-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
usb 2-2:1.0: uevent
usb 2-2:1.0: uevent
usb 2-2:1.0: uevent
usb 2-2:1.0: uevent
usb 2-3.1: uevent
usb 2-6.3: uevent
usb 2-6.1: uevent
usb 2-3.1: uevent
usb 2-6.3: uevent
usb 2-6.1: uevent
usb 2-3.1.2: uevent
usb 2-3.1.2: uevent
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
usb 2-6.3.3: uevent
usb 2-3.1.1: uevent
usb 2-6.3.3: uevent
usb 2-3.1.2.1: uevent
usb 2-3.1.1: uevent
usb 2-3.1.2.2: uevent
usb 2-3.1.2.1: uevent
usb 2-3.1.2.2: uevent
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 2-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
ACPI: SSDT 7fefa940 00175 (v01 Nvidia ASUSACPI 42302E31 AWRD 00000000)
PM: Adding info for No Bus:cooling_device1
processor LNXCPU:00: registered as cooling_device1
ACPI: SSDT 7fefad50 000CE (v01 Nvidia ASUSACPI 42302E31 AWRD 00000000)
PM: Adding info for No Bus:cooling_device2
processor LNXCPU:01: registered as cooling_device2
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
PM: Adding info for No Bus:input6
input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input6
ACPI: Power Button [PWRB]
PM: Adding info for No Bus:input7
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input7
ACPI: Power Button [PWRF]
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
PM: Adding info for No Bus:rtc
Real Time Clock Driver v1.12b
PM: Adding info for No Bus:hwmon0
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 2-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
PM: Adding info for No Bus:event0
PM: Adding info for No Bus:event1
PM: Adding info for No Bus:event2
PM: Adding info for No Bus:event3
PM: Adding info for No Bus:event4
PM: Adding info for No Bus:event5
PM: Adding info for No Bus:event6
PM: Adding info for No Bus:event7
usb 2-3.1.2.2:1.0: uevent
usb 2-3.1.2.2: uevent
usb 2-3.1.2.2:1.0: uevent
usb 2-3.1.2.2:1.0: uevent
usb 2-3.1.2.2: uevent
usb 2-3.1.2.2:1.0: uevent
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
PM: Adding info for No Bus:raw1394
ieee1394: raw1394: /dev/raw1394 device initialized
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 2-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
scsi 5:0:0:0: Direct-Access USB DISK 2.0 0403 PQ: 0 ANSI: 0 CCS
PM: Adding info for scsi:target5:0:0
PM: Adding info for scsi:5:0:0:0
PM: Adding info for No Bus:5:0:0:0
PM: Adding info for No Bus:5:0:0:0
PM: Adding info for No Bus:5:0:0:0
sd 5:0:0:0: [sdg] 3981312 512-byte logical blocks: (2.03 GB/1.89 GiB)
sd 5:0:0:0: [sdg] Write Protect is off
sd 5:0:0:0: [sdg] Mode Sense: 43 00 00 00
sd 5:0:0:0: [sdg] Assuming drive cache: write through
usb-storage: device scan complete
PM: Adding info for No Bus:sdg
sd 5:0:0:0: [sdg] Assuming drive cache: write through
sdg: sdg1
PM: Adding info for No Bus:sdg1
PM: Adding info for No Bus:8:96
sd 5:0:0:0: [sdg] Assuming drive cache: write through
sd 5:0:0:0: [sdg] Attached SCSI removable disk
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
sr0: scsi3-mmc drive: 62x/62x cd/rw xa/form2 cdda tray
PM: Adding info for No Bus:sr0
PM: Adding info for No Bus:11:0
sr 4:0:0:0: Attached scsi CD-ROM sr0
ACPI: I/O resource nForce2_smbus [0x5000-0x503f] conflicts with ACPI region SM00 [0x5000-0x5005]
ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
nForce2_smbus 0000:00:0a.1: Error probing SMB1.
PM: Adding info for i2c:i2c-0
i2c i2c-0: nForce2 SMBus adapter at 0x5100
usb 2-6.1:1.0: uevent
usb 2-6.1: uevent
usb 2-3.1.1:1.1: uevent
usb 2-3.1.1: uevent
usb 2-3.1.1:1.1: uevent
usb 2-3.1.1: uevent
usb 2-6.3.3:1.0: uevent
usb 2-6.1:1.0: uevent
usb 2-6.3.3: uevent
usb 2-6.1: uevent
usb 2-6.3.3:1.1: uevent
usb 2-6.3.3: uevent
usb 2-3.1.1:1.0: uevent
usb 2-3.1.1: uevent
usb 2-6.3.3:1.1: uevent
usb 2-6.3.3: uevent
usb 2-6.1:1.0: uevent
usb 2-3.1.1:1.1: uevent
usb 2-6.3.3:1.0: uevent
usb 2-6.1:1.0: uevent
usb 2-6.3.3:1.1: uevent
usb 2-3.1.1:1.1: uevent
usb 2-3.1.1:1.0: uevent
usb 2-6.3.3:1.1: uevent
PM: Adding info for No Bus:dv1394-0
usb 2-3.1.2.1:1.0: uevent
usb 2-3.1.2.1: uevent
usb 2-3.1.2.1:1.0: uevent
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
hda: command error: status=0x51 { DriveReady SeekComplete Error }
hda: command error: error=0x50 { LastFailedSense=0x05 }
hda: possibly failed opcode: 0xa0
end_request: I/O error, dev hda, sector 0
Buffer I/O error on device hda, logical block 0
Buffer I/O error on device hda, logical block 1
Buffer I/O error on device hda, logical block 2
Buffer I/O error on device hda, logical block 3
Buffer I/O error on device hda, logical block 4
Buffer I/O error on device hda, logical block 5
Buffer I/O error on device hda, logical block 6
Buffer I/O error on device hda, logical block 7
usb 2-3.1.2.1:1.0: uevent
usb 2-3.1.2.1: uevent
hda: command error: status=0x51 { DriveReady SeekComplete Error }
hda: command error: error=0x50 { LastFailedSense=0x05 }
hda: possibly failed opcode: 0xa0
usb 2-3.1.2.1:1.0: uevent
end_request: I/O error, dev hda, sector 0
Buffer I/O error on device hda, logical block 0
Buffer I/O error on device hda, logical block 1
hda: command error: status=0x51 { DriveReady SeekComplete Error }
hda: command error: error=0x50 { LastFailedSense=0x05 }
hda: possibly failed opcode: 0xa0
end_request: I/O error, dev hda, sector 0
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 2-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
PM: Adding info for No Bus:sg0
sd 1:0:0:0: Attached scsi generic sg0 type 0
PM: Adding info for No Bus:sg1
sd 2:0:0:0: Attached scsi generic sg1 type 0
PM: Adding info for No Bus:sg2
sr 4:0:0:0: Attached scsi generic sg2 type 5
PM: Adding info for No Bus:sg3
sd 0:0:0:0: Attached scsi generic sg3 type 0
PM: Adding info for No Bus:sg4
sd 0:0:0:1: Attached scsi generic sg4 type 0
PM: Adding info for No Bus:sg5
sd 0:0:0:2: Attached scsi generic sg5 type 0
PM: Adding info for No Bus:sg6
sd 0:0:0:3: Attached scsi generic sg6 type 0
PM: Adding info for No Bus:sg7
sd 5:0:0:0: Attached scsi generic sg7 type 0
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
PM: Adding info for No Bus:timer
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
PM: Adding info for No Bus:seq
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030300 PESC CSC LSDA PPS
hub 1-0:1.0: port 1, status 0300, change 0003, 1.5 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x300
hda: UDMA/66 mode selected
PM: Adding info for No Bus:sequencer
PM: Adding info for No Bus:sequencer2
ACPI: PCI Interrupt Link [AAZA] enabled at IRQ 23
HDA Intel 0000:00:10.1: PCI INT B -> Link[AAZA] -> GSI 23 (level, low) -> IRQ 23
HDA Intel 0000:00:10.1: setting latency timer to 64
PM: Adding info for No Bus:input8
input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:10.1/input/input8
PM: Adding info for No Bus:event8
PM: Adding info for No Bus:card0
PM: Adding info for No Bus:pcmC0D1p
PM: Adding info for No Bus:adsp
PM: Adding info for No Bus:pcmC0D0p
PM: Adding info for No Bus:pcmC0D0c
PM: Adding info for No Bus:dsp
PM: Adding info for No Bus:audio
PM: Adding info for No Bus:hwC0D0
PM: Adding info for No Bus:controlC0
PM: Adding info for No Bus:mixer
ohci_hcd 0000:00:0b.0: auto-stop root hub
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
sr 4:0:0:0: [sr0] CDB: Read(10): 28 00 00 00 00 00 00 00 40 00
ata4.00: cmd a0/01:00:00:00:fc/00:00:00:00:00/a0 tag 0 dma 131072 in
res 40/00:02:00:20:00/00:00:00:00:00/a0 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for UDMA/100
ata4: EH complete
ata4: limiting SATA link speed to 1.5 Gbps
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
sr 4:0:0:0: [sr0] CDB: Read(10): 28 00 00 00 00 00 00 00 40 00
ata4.00: cmd a0/01:00:00:00:fc/00:00:00:00:00/a0 tag 0 dma 131072 in
res 40/00:02:00:20:00/00:00:00:00:00/a0 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for UDMA/100
ata4: EH complete
ata4.00: limiting speed to UDMA/66:PIO4
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
sr 4:0:0:0: [sr0] CDB: Read(10): 28 00 00 00 00 00 00 00 40 00
ata4.00: cmd a0/01:00:00:00:fc/00:00:00:00:00/a0 tag 0 dma 131072 in
res 40/00:02:00:20:00/00:00:00:00:00/a0 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for UDMA/66
ata4: EH complete
ata4.00: limiting speed to UDMA/33:PIO4
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
sr 4:0:0:0: [sr0] CDB: Read(10): 28 00 00 00 00 00 00 00 40 00
ata4.00: cmd a0/01:00:00:00:fc/00:00:00:00:00/a0 tag 0 dma 131072 in
res 40/00:02:00:20:00/00:00:00:00:00/a0 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for UDMA/33
sr 4:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
sr 4:0:0:0: [sr0] Sense Key : Aborted Command [current] [descriptor]
Descriptor sense data with sense descriptors (in hex):
72 0b 00 00 00 00 00 0e 09 0c 00 00 00 02 00 00
00 20 00 00 a0 40
sr 4:0:0:0: [sr0] Add. Sense: No additional sense information
sr 4:0:0:0: [sr0] CDB: Read(10): 28 00 00 00 00 00 00 00 40 00
end_request: I/O error, dev sr0, sector 0
__ratelimit: 2 callbacks suppressed
Buffer I/O error on device sr0, logical block 0
Buffer I/O error on device sr0, logical block 1
Buffer I/O error on device sr0, logical block 2
Buffer I/O error on device sr0, logical block 3
Buffer I/O error on device sr0, logical block 4
Buffer I/O error on device sr0, logical block 5
Buffer I/O error on device sr0, logical block 6
Buffer I/O error on device sr0, logical block 7
Buffer I/O error on device sr0, logical block 8
Buffer I/O error on device sr0, logical block 9
ata4: EH complete
ata4.00: limiting speed to PIO4
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
sr 4:0:0:0: [sr0] CDB: Read(10): 28 00 00 00 00 00 00 00 08 00
ata4.00: cmd a0/01:00:00:00:40/00:00:00:00:00/a0 tag 0 dma 16384 in
res 40/00:02:00:20:00/00:00:00:00:00/a0 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO4
ata4: EH complete
PM: Adding info for No Bus:vcs2
PM: Adding info for No Bus:vcsa2
PM: Adding info for No Bus:vcs3
PM: Adding info for No Bus:vcsa3
PM: Adding info for No Bus:vcs4
PM: Adding info for No Bus:vcsa4
PM: Adding info for No Bus:vcs5
PM: Adding info for No Bus:vcsa5
PM: Adding info for No Bus:vcs6
PM: Adding info for No Bus:vcsa6
hda: UDMA/66 mode selected
EXT3 FS on dm-1, internal journal
i2c /dev entries driver
PM: Adding info for No Bus:i2c-0
it87: Found IT8712F chip at 0x290, revision 7
it87: in3 is VCC (+5V)
it87: in7 is VCCH (+5V Stand-By)
ACPI: I/O resource it87 [0x295-0x296] conflicts with ACPI region HWRE [0x295-0x296]
ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
fuse init (API version 7.13)
PM: Adding info for No Bus:fuse
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-5, internal journal
EXT3-fs: mounted filesystem with writeback data mode.
PM: Adding info for No Bus:254:2-fuseblk
PM: Adding info for No Bus:254:6-fuseblk
Adding 4194296k swap on /mnt/oldlin/4G-memory.swap. Priority:-1 extents:1057 across:4264956k
r8169: eth1: link up
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PM: Adding info for No Bus:0:16
PM: Adding info for No Bus:0:17
PM: Adding info for No Bus:0:18
r8169: eth1: link up
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: sata_nv times out for BD-ROM iHOS104-08
2010-03-08 19:17 ` Cengiz Günay
@ 2010-03-08 23:46 ` Robert Hancock
2010-03-09 1:21 ` Tejun Heo
1 sibling, 0 replies; 28+ messages in thread
From: Robert Hancock @ 2010-03-08 23:46 UTC (permalink / raw)
To: Cengiz Günay; +Cc: Tejun Heo, linux-kernel, linux-ide
2010/3/8 Cengiz Günay <cgunay@emory.edu>:
> Hello,
>
> Sorry for the delay, I was confused about managing so many patches,
> but I realized that you're sending me cumulative patches that I can
> apply to the original. I just want to remind you that I still have the
> patches to the other two files: libata-eh.c libata-sff.c
>
> On Tue, Mar 2, 2010 at 6:48 AM, Tejun Heo <tj@kernel.org> wrote:
>> Hmmm... the drive is timing out even on 4k READ10's. This shouldn't
>> really be happening. Can you please try this one?
>
> Applied. It did not change anything visibly (dmesg attached). I have
> also been getting other SCSI errors since we started communicating
> with the device (search for sr0 in dmesg). I wonder if they give any
> hints? Here's one:
>
> sr 4:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
> sr 4:0:0:0: [sr0] Sense Key : Aborted Command [current] [descriptor]
> Descriptor sense data with sense descriptors (in hex):
> 72 0b 00 00 00 00 00 0e 09 0c 00 00 00 02 00 00
> 00 20 00 00 a0 40
> sr 4:0:0:0: [sr0] Add. Sense: No additional sense information
> sr 4:0:0:0: [sr0] CDB: Read(10): 28 00 00 00 00 00 00 00 40 00
> end_request: I/O error, dev sr0, sector 0
Don't think that part's very useful, that's just the after-effect of
the timeouts in the driver..
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: sata_nv times out for BD-ROM iHOS104-08
2010-03-08 19:17 ` Cengiz Günay
2010-03-08 23:46 ` Robert Hancock
@ 2010-03-09 1:21 ` Tejun Heo
2010-03-09 5:18 ` Cengiz Günay
1 sibling, 1 reply; 28+ messages in thread
From: Tejun Heo @ 2010-03-09 1:21 UTC (permalink / raw)
To: Cengiz Günay; +Cc: Robert Hancock, linux-kernel, linux-ide
On 03/09/2010 04:17 AM, Cengiz Günay wrote:
> Hello,
>
> Sorry for the delay, I was confused about managing so many patches,
> but I realized that you're sending me cumulative patches that I can
> apply to the original. I just want to remind you that I still have the
> patches to the other two files: libata-eh.c libata-sff.c
>
> On Tue, Mar 2, 2010 at 6:48 AM, Tejun Heo <tj@kernel.org> wrote:
>> Hmmm... the drive is timing out even on 4k READ10's. This shouldn't
>> really be happening. Can you please try this one?
>
> Applied. It did not change anything visibly (dmesg attached). I have
> also been getting other SCSI errors since we started communicating
> with the device (search for sr0 in dmesg). I wonder if they give any
> hints? Here's one:
>
> sr 4:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
> sr 4:0:0:0: [sr0] Sense Key : Aborted Command [current] [descriptor]
> Descriptor sense data with sense descriptors (in hex):
> 72 0b 00 00 00 00 00 0e 09 0c 00 00 00 02 00 00
> 00 20 00 00 a0 40
> sr 4:0:0:0: [sr0] Add. Sense: No additional sense information
> sr 4:0:0:0: [sr0] CDB: Read(10): 28 00 00 00 00 00 00 00 40 00
> end_request: I/O error, dev sr0, sector 0
Hmmm... can you please post full dmesg?
--
tejun
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: sata_nv times out for BD-ROM iHOS104-08
2010-03-09 1:21 ` Tejun Heo
@ 2010-03-09 5:18 ` Cengiz Günay
2010-05-25 19:34 ` Tejun Heo
0 siblings, 1 reply; 28+ messages in thread
From: Cengiz Günay @ 2010-03-09 5:18 UTC (permalink / raw)
To: Tejun Heo; +Cc: Robert Hancock, linux-kernel, linux-ide
[-- Attachment #1: Type: text/plain, Size: 1873 bytes --]
Ok, I see. BTW, the full dmesg was attached to that message. I'm
attaching it again.
-Cengiz
On Mon, Mar 8, 2010 at 8:21 PM, Tejun Heo <tj@kernel.org> wrote:
> On 03/09/2010 04:17 AM, Cengiz Günay wrote:
>> Hello,
>>
>> Sorry for the delay, I was confused about managing so many patches,
>> but I realized that you're sending me cumulative patches that I can
>> apply to the original. I just want to remind you that I still have the
>> patches to the other two files: libata-eh.c libata-sff.c
>>
>> On Tue, Mar 2, 2010 at 6:48 AM, Tejun Heo <tj@kernel.org> wrote:
>>> Hmmm... the drive is timing out even on 4k READ10's. This shouldn't
>>> really be happening. Can you please try this one?
>>
>> Applied. It did not change anything visibly (dmesg attached). I have
>> also been getting other SCSI errors since we started communicating
>> with the device (search for sr0 in dmesg). I wonder if they give any
>> hints? Here's one:
>>
>> sr 4:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
>> sr 4:0:0:0: [sr0] Sense Key : Aborted Command [current] [descriptor]
>> Descriptor sense data with sense descriptors (in hex):
>> 72 0b 00 00 00 00 00 0e 09 0c 00 00 00 02 00 00
>> 00 20 00 00 a0 40
>> sr 4:0:0:0: [sr0] Add. Sense: No additional sense information
>> sr 4:0:0:0: [sr0] CDB: Read(10): 28 00 00 00 00 00 00 00 40 00
>> end_request: I/O error, dev sr0, sector 0
>
> Hmmm... can you please post full dmesg?
>
> --
> tejun
>
--
Cengiz Gunay
--
Postdoctoral Fellow
Prinz Lab, Dept. of Biology, Emory University
1510 Clifton Rd., Room 2172, Atlanta, GA 30322, U.S.A.
cgunay@emory.edu cengique@users.sf.net cengique@yahoo.com
Lab: +1-404-727-9381 Home/Cell: +1-678-559-8694
http://userwww.service.emory.edu/~cgunay
ICQ# 21104923, cengique@{jabber.org,Skype}
--
[-- Attachment #2: dmesg-sata_nv-swncq-atapi-pio-patch-2 --]
[-- Type: application/octet-stream, Size: 90870 bytes --]
Linux version 2.6.32testing (root@salon) (gcc version 4.3.3 (Debian 4.3.3-10) ) #6 SMP PREEMPT Mon Mar 8 13:09:55 EST 2010
KERNEL supported cpus:
Intel GenuineIntel
AMD AuthenticAMD
NSC Geode by NSC
Cyrix CyrixInstead
Centaur CentaurHauls
Transmeta GenuineTMx86
Transmeta TransmetaCPU
UMC UMC UMC UMC
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009c400 (usable)
BIOS-e820: 000000000009c400 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000007fef0000 (usable)
BIOS-e820: 000000007fef0000 - 000000007fef3000 (ACPI NVS)
BIOS-e820: 000000007fef3000 - 000000007ff00000 (ACPI data)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
DMI 2.4 present.
Phoenix BIOS detected: BIOS may corrupt low RAM, working around it.
e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
last_pfn = 0x7fef0 max_arch_pfn = 0x100000
MTRR default type: uncachable
MTRR fixed ranges enabled:
00000-9FFFF write-back
A0000-BFFFF uncachable
C0000-CDFFF write-protect
CE000-FFFFF uncachable
MTRR variable ranges enabled:
0 base 000000000 mask F80000000 write-back
1 base 07FF00000 mask FFFF00000 uncachable
2 disabled
3 disabled
4 disabled
5 disabled
6 disabled
7 disabled
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
initial memory mapped : 0 - 01800000
init_memory_mapping: 0000000000000000-00000000377fe000
0000000000 - 0000400000 page 4k
0000400000 - 0037400000 page 2M
0037400000 - 00377fe000 page 4k
kernel direct mapping tables up to 377fe000 @ 10000-15000
RAMDISK: 36bad000 - 37fef0ec
Allocated new RAMDISK: 013e6000 - 028280ec
Move RAMDISK from 0000000036bad000 - 0000000037fef0eb to 013e6000 - 028280eb
ACPI: RSDP 000f7900 00024 (v02 Nvidia)
ACPI: XSDT 7fef30c0 0004C (v01 Nvidia ASUSACPI 42302E31 AWRD 00000000)
ACPI: FACP 7fefa600 000F4 (v03 Nvidia ASUSACPI 42302E31 AWRD 00000000)
ACPI: DSDT 7fef3240 07354 (v01 NVIDIA ASUSACPI 00001000 MSFT 03000000)
ACPI: FACS 7fef0000 00040
ACPI: HPET 7fefa840 00038 (v01 Nvidia ASUSACPI 42302E31 AWRD 00000098)
ACPI: MCFG 7fefa8c0 0003C (v01 Nvidia ASUSACPI 42302E31 AWRD 00000000)
ACPI: APIC 7fefa740 0008E (v01 Nvidia ASUSACPI 42302E31 AWRD 00000000)
ACPI: SSDT 7fefae20 0032C (v01 Nvidia ASUSACPI 42302E31 AWRD 00000000)
ACPI: Local APIC address 0xfee00000
1158MB HIGHMEM available.
887MB LOWMEM available.
mapped low ram: 0 - 377fe000
low ram: 0 - 377fe000
node 0 low ram: 00000000 - 377fe000
node 0 bootmap 00011000 - 00017f00
(9 early reservations) ==> bootmem [0000000000 - 00377fe000]
#0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
#1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000]
#2 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 - 0000007000]
#3 [0001000000 - 00013de7c4] TEXT DATA BSS ==> [0001000000 - 00013de7c4]
#4 [000009c400 - 0000100000] BIOS reserved ==> [000009c400 - 0000100000]
#5 [00013df000 - 00013e5149] BRK ==> [00013df000 - 00013e5149]
#6 [0000010000 - 0000011000] PGTABLE ==> [0000010000 - 0000011000]
#7 [00013e6000 - 00028280ec] NEW RAMDISK ==> [00013e6000 - 00028280ec]
#8 [0000011000 - 0000018000] BOOTMAP ==> [0000011000 - 0000018000]
found SMP MP-table at [c00f5d50] f5d50
Zone PFN ranges:
DMA 0x00000010 -> 0x00001000
Normal 0x00001000 -> 0x000377fe
HighMem 0x000377fe -> 0x0007fef0
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
0: 0x00000010 -> 0x0000009c
0: 0x00000100 -> 0x0007fef0
On node 0 totalpages: 523900
free_area_init_node: node 0, pgdat c1324fc0, node_mem_map c282a200
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 3948 pages, LIFO batch:0
Normal zone: 1744 pages used for memmap
Normal zone: 221486 pages, LIFO batch:31
HighMem zone: 2318 pages used for memmap
HighMem zone: 294372 pages, LIFO batch:31
Using APIC driver default
ACPI: PM-Timer IO Port: 0x4008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 4, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
ACPI: IRQ9 used by override.
ACPI: IRQ14 used by override.
ACPI: IRQ15 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
ACPI: HPET id: 0x10de8201 base: 0xfeff0000
SMP: Allowing 4 CPUs, 2 hotplug CPUs
nr_irqs_gsi: 24
PM: Registered nosave memory: 000000000009c000 - 000000000009d000
PM: Registered nosave memory: 000000000009d000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
Allocating PCI resources starting at 7ff00000 (gap: 7ff00000:60100000)
NR_CPUS:4 nr_cpumask_bits:4 nr_cpu_ids:4 nr_node_ids:1
PERCPU: Embedded 11 pages/cpu @c3c00000 s23512 r0 d21544 u1048576
pcpu-alloc: s23512 r0 d21544 u1048576 alloc=1*4194304
pcpu-alloc: [0] 0 1 2 3
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 519806
Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.32testing root=/dev/mapper/nvidia_ceebaiib1 ro single
PID hash table entries: 4096 (order: 2, 16384 bytes)
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
Initializing HighMem for node 0 (000377fe:0007fef0)
Memory: 2052264k/2096064k available (2319k kernel code, 42160k reserved, 912k data, 404k init, 1186760k highmem)
virtual kernel memory layout:
fixmap : 0xfff6b000 - 0xfffff000 ( 592 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xf7ffe000 - 0xff7fe000 ( 120 MB)
lowmem : 0xc0000000 - 0xf77fe000 ( 887 MB)
.init : 0xc1329000 - 0xc138e000 ( 404 kB)
.data : 0xc1243e41 - 0xc1328128 ( 912 kB)
.text : 0xc1000000 - 0xc1243e41 (2319 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:384
Extended CMOS year: 2000
spurious 8259A interrupt: IRQ7.
Console: colour VGA+ 80x25
console [tty0] enabled
hpet clockevent registered
Fast TSC calibration using PIT
Detected 2133.576 MHz processor.
Calibrating delay loop (skipped), value calculated using timer frequency.. 4267.15 BogoMIPS (lpj=2133576)
Security Framework initialized
Mount-cache hash table entries: 512
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
mce: CPU supports 6 MCE banks
CPU0: Thermal monitoring enabled (TM2)
using mwait in idle threads.
Checking 'hlt' instruction... OK.
ACPI: Core revision 20090903
..TIMER: vector=0x30 apic1=0 pin1=0 apic2=-1 pin2=-1
..MP-BIOS bug: 8254 timer not connected to IO-APIC
...trying to set up timer (IRQ0) through the 8259A ...
..... (found apic 0 pin 0) ...
....... works.
CPU0: Intel(R) Core(TM)2 CPU 6400 @ 2.13GHz stepping 06
Booting processor 1 APIC 0x1 ip 0x6000
Initializing CPU#1
Calibrating delay using timer specific routine.. 4266.57 BogoMIPS (lpj=2133287)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU1: Thermal monitoring enabled (TM2)
CPU1: Intel(R) Core(TM)2 CPU 6400 @ 2.13GHz stepping 06
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Brought up 2 CPUs
Total of 2 processors activated (8533.72 BogoMIPS).
CPU0 attaching sched-domain:
domain 0: span 0-1 level MC
groups: 0 1
CPU1 attaching sched-domain:
domain 0: span 0-1 level MC
groups: 1 0
PM: Adding info for No Bus:platform
Time: 13:54:06 Date: 03/08/10
NET: Registered protocol family 16
PM: Adding info for No Bus:vtcon0
EISA bus registered
ACPI: bus type pci registered
PM: Adding info for No Bus:id
PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
PCI: MCFG area at e0000000 reserved in E820
PCI: Using MMCONFIG for extended config space
PCI: Using configuration type 1 for base access
PM: Adding info for No Bus:default
bio: create slab <bio-0> at 0
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
PM: Adding info for acpi:LNXSYSTM:00
PM: Adding info for acpi:LNXCPU:00
PM: Adding info for acpi:LNXCPU:01
PM: Adding info for acpi:LNXCPU:02
PM: Adding info for acpi:LNXCPU:03
PM: Adding info for acpi:LNXSYBUS:00
PM: Adding info for acpi:PNP0C0C:00
PM: Adding info for acpi:PNP0A08:00
PM: Adding info for acpi:PNP0C02:00
PM: Adding info for acpi:device:00
PM: Adding info for acpi:device:01
PM: Adding info for acpi:device:02
PM: Adding info for acpi:device:03
PM: Adding info for acpi:device:04
PM: Adding info for acpi:device:05
PM: Adding info for acpi:device:06
PM: Adding info for acpi:device:07
PM: Adding info for acpi:device:08
PM: Adding info for acpi:device:09
PM: Adding info for acpi:device:0a
PM: Adding info for acpi:device:0b
PM: Adding info for acpi:device:0c
PM: Adding info for acpi:device:0d
PM: Adding info for acpi:device:0e
PM: Adding info for acpi:device:0f
PM: Adding info for acpi:device:10
PM: Adding info for acpi:device:11
PM: Adding info for acpi:device:12
PM: Adding info for acpi:device:13
PM: Adding info for acpi:device:14
PM: Adding info for acpi:device:15
PM: Adding info for acpi:device:16
PM: Adding info for acpi:device:17
PM: Adding info for acpi:device:18
PM: Adding info for acpi:device:19
PM: Adding info for acpi:PNP0C02:01
PM: Adding info for acpi:PNP0000:00
PM: Adding info for acpi:PNP0200:00
PM: Adding info for acpi:PNP0100:00
PM: Adding info for acpi:PNP0103:00
PM: Adding info for acpi:PNP0B00:00
PM: Adding info for acpi:PNP0800:00
PM: Adding info for acpi:PNP0C04:00
PM: Adding info for acpi:device:1a
PM: Adding info for acpi:device:1b
PM: Adding info for acpi:device:1c
PM: Adding info for acpi:device:1d
PM: Adding info for acpi:device:1e
PM: Adding info for acpi:device:1f
PM: Adding info for acpi:NVRAIDBUS:00
PM: Adding info for acpi:ATK0110:00
PM: Adding info for acpi:PNP0C0F:00
PM: Adding info for acpi:PNP0C0F:01
PM: Adding info for acpi:PNP0C0F:02
PM: Adding info for acpi:PNP0C0F:03
PM: Adding info for acpi:PNP0C0F:04
PM: Adding info for acpi:PNP0C0F:05
PM: Adding info for acpi:PNP0C0F:06
PM: Adding info for acpi:PNP0C0F:07
PM: Adding info for acpi:PNP0C0F:08
PM: Adding info for acpi:PNP0C0F:09
PM: Adding info for acpi:PNP0C0F:0a
PM: Adding info for acpi:PNP0C0F:0b
PM: Adding info for acpi:PNP0C0F:0c
PM: Adding info for acpi:PNP0C0F:0d
PM: Adding info for acpi:PNP0C0F:0e
PM: Adding info for acpi:PNP0C0F:0f
PM: Adding info for acpi:PNP0C0F:10
PM: Adding info for acpi:PNP0C0F:11
PM: Adding info for acpi:PNP0C0F:12
PM: Adding info for acpi:PNP0C0F:13
PM: Adding info for acpi:PNP0C0F:14
PM: Adding info for acpi:PNP0C0F:15
PM: Adding info for acpi:PNP0C0F:16
PM: Adding info for acpi:PNP0C0F:17
PM: Adding info for acpi:PNP0C0F:18
PM: Adding info for acpi:PNP0C0F:19
PM: Adding info for acpi:PNP0C0F:1a
PM: Adding info for acpi:PNP0C0F:1b
PM: Adding info for acpi:PNP0C0F:1c
PM: Adding info for acpi:PNP0C0F:1d
PM: Adding info for acpi:PNP0C0F:1e
PM: Adding info for acpi:PNP0C0F:1f
PM: Adding info for acpi:PNP0C0F:20
PM: Adding info for acpi:PNP0C0F:21
PM: Adding info for acpi:PNP0C0F:22
PM: Adding info for acpi:PNP0C0F:23
PM: Adding info for acpi:PNP0C0F:24
PM: Adding info for acpi:PNP0C0F:25
PM: Adding info for acpi:PNP0C0F:26
PM: Adding info for acpi:PNP0C0F:27
PM: Adding info for acpi:PNP0C0F:28
PM: Adding info for acpi:PNP0C02:02
PM: Adding info for acpi:PNP0C01:00
PM: Adding info for acpi:LNXTHERM:00
PM: Adding info for acpi:PNP0C0B:00
PM: Adding info for acpi:LNXTHERM:01
PM: Adding info for acpi:LNXPWRBN:00
ACPI: No dock devices found.
ACPI: PCI Root Bridge [PCI0] (0000:00)
PM: Adding info for No Bus:pci0000:00
PM: Adding info for No Bus:0000:00
pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:02.0: PME# disabled
pci 0000:00:04.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:04.0: PME# disabled
pci 0000:00:05.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:05.0: PME# disabled
pci 0000:00:06.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:06.0: PME# disabled
pci 0000:00:07.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:07.0: PME# disabled
pci 0000:00:0a.1: reg 20 io port: [0x5000-0x503f]
pci 0000:00:0a.1: reg 24 io port: [0x5100-0x513f]
pci 0000:00:0a.1: PME# supported from D3hot D3cold
pci 0000:00:0a.1: PME# disabled
pci 0000:00:0b.0: reg 10 32bit mmio: [0xd5006000-0xd5006fff]
pci 0000:00:0b.0: supports D1 D2
pci 0000:00:0b.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:0b.0: PME# disabled
pci 0000:00:0b.1: reg 10 32bit mmio: [0xd5007000-0xd50070ff]
pci 0000:00:0b.1: supports D1 D2
pci 0000:00:0b.1: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:0b.1: PME# disabled
pci 0000:00:0d.0: reg 20 io port: [0xf000-0xf00f]
pci 0000:00:0e.0: reg 10 io port: [0x9f0-0x9f7]
pci 0000:00:0e.0: reg 14 io port: [0xbf0-0xbf3]
pci 0000:00:0e.0: reg 18 io port: [0x970-0x977]
pci 0000:00:0e.0: reg 1c io port: [0xb70-0xb73]
pci 0000:00:0e.0: reg 20 io port: [0xd400-0xd40f]
pci 0000:00:0e.0: reg 24 32bit mmio: [0xd5004000-0xd5004fff]
pci 0000:00:0f.0: reg 10 io port: [0x9e0-0x9e7]
pci 0000:00:0f.0: reg 14 io port: [0xbe0-0xbe3]
pci 0000:00:0f.0: reg 18 io port: [0x960-0x967]
pci 0000:00:0f.0: reg 1c io port: [0xb60-0xb63]
pci 0000:00:0f.0: reg 20 io port: [0xe800-0xe80f]
pci 0000:00:0f.0: reg 24 32bit mmio: [0xd5005000-0xd5005fff]
pci 0000:00:10.1: reg 10 32bit mmio: [0xd5000000-0xd5003fff]
pci 0000:00:10.1: PME# supported from D3hot D3cold
pci 0000:00:10.1: PME# disabled
pci 0000:01:00.0: reg 10 32bit mmio: [0xd0000000-0xd0ffffff]
pci 0000:01:00.0: reg 14 64bit mmio pref: [0xc0000000-0xcfffffff]
pci 0000:01:00.0: reg 1c 64bit mmio: [0xd1000000-0xd1ffffff]
pci 0000:01:00.0: reg 24 io port: [0xa000-0xa07f]
pci 0000:01:00.0: reg 30 32bit mmio pref: [0xd2000000-0xd201ffff]
pci 0000:00:02.0: bridge io port: [0xa000-0xafff]
pci 0000:00:02.0: bridge 32bit mmio: [0xd0000000-0xd2ffffff]
pci 0000:00:02.0: bridge 64bit mmio pref: [0xc0000000-0xcfffffff]
pci 0000:06:06.0: reg 10 32bit mmio: [0xd4001000-0xd40017ff]
pci 0000:06:06.0: reg 14 io port: [0xb000-0xb07f]
pci 0000:06:06.0: supports D2
pci 0000:06:06.0: PME# supported from D2 D3hot D3cold
pci 0000:06:06.0: PME# disabled
pci 0000:06:07.0: reg 10 io port: [0xb400-0xb4ff]
pci 0000:06:07.0: reg 14 32bit mmio: [0xd4000000-0xd40000ff]
pci 0000:06:07.0: reg 30 32bit mmio pref: [0xd3000000-0xd301ffff]
pci 0000:06:07.0: supports D1 D2
pci 0000:06:07.0: PME# supported from D1 D2 D3hot D3cold
pci 0000:06:07.0: PME# disabled
pci 0000:00:10.0: transparent bridge
pci 0000:00:10.0: bridge io port: [0xb000-0xbfff]
pci 0000:00:10.0: bridge 32bit mmio: [0xd3000000-0xd4ffffff]
pci_bus 0000:00: on NUMA node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
PM: Adding info for pci:0000:00:00.0
PM: Adding info for pci:0000:00:00.1
PM: Adding info for pci:0000:00:00.2
PM: Adding info for pci:0000:00:00.3
PM: Adding info for pci:0000:00:00.4
PM: Adding info for pci:0000:00:01.0
PM: Adding info for pci:0000:00:01.1
PM: Adding info for pci:0000:00:01.2
PM: Adding info for pci:0000:00:01.3
PM: Adding info for pci:0000:00:01.4
PM: Adding info for pci:0000:00:01.5
PM: Adding info for pci:0000:00:01.6
PM: Adding info for pci:0000:00:02.0
PM: Adding info for pci:0000:00:04.0
PM: Adding info for pci:0000:00:05.0
PM: Adding info for pci:0000:00:06.0
PM: Adding info for pci:0000:00:07.0
PM: Adding info for pci:0000:00:09.0
PM: Adding info for pci:0000:00:0a.0
PM: Adding info for pci:0000:00:0a.1
PM: Adding info for pci:0000:00:0a.2
PM: Adding info for pci:0000:00:0b.0
PM: Adding info for pci:0000:00:0b.1
PM: Adding info for pci:0000:00:0d.0
PM: Adding info for pci:0000:00:0e.0
PM: Adding info for pci:0000:00:0f.0
PM: Adding info for pci:0000:00:10.0
PM: Adding info for pci:0000:00:10.1
PM: Adding info for pci:0000:01:00.0
PM: Adding info for No Bus:0000:01
PM: Adding info for No Bus:0000:02
PM: Adding info for No Bus:0000:03
PM: Adding info for No Bus:0000:04
PM: Adding info for No Bus:0000:05
PM: Adding info for pci:0000:06:06.0
PM: Adding info for pci:0000:06:07.0
PM: Adding info for No Bus:0000:06
ACPI: PCI Interrupt Link [LNK1] (IRQs 5 7 9 *10 11 14 15)
ACPI: PCI Interrupt Link [LNK2] (IRQs *5 7 9 10 11 14 15)
ACPI: PCI Interrupt Link [LNK3] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK4] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK5] (IRQs 5 *7 9 10 11 14 15)
ACPI: PCI Interrupt Link [LNK6] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK7] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK8] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LUBA] (IRQs 5 *7 9 10 11 14 15)
ACPI: PCI Interrupt Link [LUBB] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LMAC] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LACI] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LAZA] (IRQs 5 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [LPMU] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LMCI] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSMB] (IRQs 5 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [LUB2] (IRQs *5 7 9 10 11 14 15)
ACPI: PCI Interrupt Link [LIDE] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSID] (IRQs 5 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [LFID] (IRQs 5 7 9 *10 11 14 15)
ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0
ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0
ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0, disabled.
ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled.
ACPI: PCI Interrupt Link [APC5] (IRQs 16) *0
ACPI: PCI Interrupt Link [APC6] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APC7] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APC8] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APMU] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [AAZA] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0
PM: Adding info for No Bus:vga_arbiter
vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
vgaarb: loaded
PCI: Using ACPI for IRQ routing
PM: Adding info for No Bus:lo
hpet0: at MMIO 0xfeff0000, IRQs 2, 8, 31
hpet0: 3 comparators, 32-bit 25.000000 MHz counter
Switching to clocksource tsc
pnp: PnP ACPI init
PM: Adding info for No Bus:pnp0
ACPI: bus type pnp registered
PM: Adding info for pnp:00:00
PM: Adding info for pnp:00:01
PM: Adding info for pnp:00:02
PM: Adding info for pnp:00:03
PM: Adding info for pnp:00:04
PM: Adding info for pnp:00:05
PM: Adding info for pnp:00:06
PM: Adding info for pnp:00:07
PM: Adding info for pnp:00:08
PM: Adding info for pnp:00:09
pnp: PnP ACPI: found 10 devices
ACPI: ACPI bus type pnp unregistered
PnPBIOS: Disabled by ACPI PNP
system 00:01: ioport range 0x4000-0x407f has been reserved
system 00:01: ioport range 0x4080-0x40ff has been reserved
system 00:01: ioport range 0x4400-0x447f has been reserved
system 00:01: ioport range 0x4480-0x44ff has been reserved
system 00:01: ioport range 0x4800-0x487f has been reserved
system 00:01: ioport range 0x4880-0x48ff has been reserved
system 00:02: ioport range 0x4d0-0x4d1 has been reserved
system 00:02: ioport range 0x800-0x87f has been reserved
system 00:02: ioport range 0x290-0x297 has been reserved
system 00:02: ioport range 0x880-0x88f has been reserved
system 00:08: iomem range 0xe0000000-0xefffffff has been reserved
system 00:09: iomem range 0xdbc00-0xdbfff has been reserved
system 00:09: iomem range 0xf0000-0xf7fff could not be reserved
system 00:09: iomem range 0xf8000-0xfbfff could not be reserved
system 00:09: iomem range 0xfc000-0xfffff could not be reserved
system 00:09: iomem range 0xfeff0000-0xfeff00ff has been reserved
system 00:09: iomem range 0x7fef0000-0x7fefffff could not be reserved
system 00:09: iomem range 0xffff0000-0xffffffff has been reserved
system 00:09: iomem range 0x0-0x9ffff could not be reserved
system 00:09: iomem range 0x100000-0x7feeffff could not be reserved
system 00:09: iomem range 0xfec00000-0xfec00fff could not be reserved
system 00:09: iomem range 0xfee00000-0xfee00fff has been reserved
system 00:09: iomem range 0xfeff0000-0xfeff03ff could not be reserved
PM: Adding info for No Bus:mem
PM: Adding info for No Bus:kmem
PM: Adding info for No Bus:null
PM: Adding info for No Bus:port
PM: Adding info for No Bus:zero
PM: Adding info for No Bus:full
PM: Adding info for No Bus:random
PM: Adding info for No Bus:urandom
PM: Adding info for No Bus:kmsg
pci 0000:06:07.0: BAR 6: address space collision on of device [0xd3000000-0xd301ffff]
pci 0000:00:02.0: PCI bridge, secondary bus 0000:01
pci 0000:00:02.0: IO window: 0xa000-0xafff
pci 0000:00:02.0: MEM window: 0xd0000000-0xd2ffffff
pci 0000:00:02.0: PREFETCH window: 0x000000c0000000-0x000000cfffffff
pci 0000:00:04.0: PCI bridge, secondary bus 0000:02
pci 0000:00:04.0: IO window: disabled
pci 0000:00:04.0: MEM window: disabled
pci 0000:00:04.0: PREFETCH window: disabled
pci 0000:00:05.0: PCI bridge, secondary bus 0000:03
pci 0000:00:05.0: IO window: disabled
pci 0000:00:05.0: MEM window: disabled
pci 0000:00:05.0: PREFETCH window: disabled
pci 0000:00:06.0: PCI bridge, secondary bus 0000:04
pci 0000:00:06.0: IO window: disabled
pci 0000:00:06.0: MEM window: disabled
pci 0000:00:06.0: PREFETCH window: disabled
pci 0000:00:07.0: PCI bridge, secondary bus 0000:05
pci 0000:00:07.0: IO window: disabled
pci 0000:00:07.0: MEM window: disabled
pci 0000:00:07.0: PREFETCH window: disabled
pci 0000:00:10.0: PCI bridge, secondary bus 0000:06
pci 0000:00:10.0: IO window: 0xb000-0xbfff
pci 0000:00:10.0: MEM window: 0xd3000000-0xd4ffffff
pci 0000:00:10.0: PREFETCH window: 0x80000000-0x800fffff
pci 0000:00:02.0: setting latency timer to 64
pci 0000:00:04.0: setting latency timer to 64
pci 0000:00:05.0: setting latency timer to 64
pci 0000:00:06.0: setting latency timer to 64
pci 0000:00:07.0: setting latency timer to 64
pci 0000:00:10.0: setting latency timer to 64
pci_bus 0000:00: resource 0 io: [0x00-0xffff]
pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
pci_bus 0000:01: resource 0 io: [0xa000-0xafff]
pci_bus 0000:01: resource 1 mem: [0xd0000000-0xd2ffffff]
pci_bus 0000:01: resource 2 pref mem [0xc0000000-0xcfffffff]
pci_bus 0000:06: resource 0 io: [0xb000-0xbfff]
pci_bus 0000:06: resource 1 mem: [0xd3000000-0xd4ffffff]
pci_bus 0000:06: resource 2 pref mem [0x80000000-0x800fffff]
pci_bus 0000:06: resource 3 io: [0x00-0xffff]
pci_bus 0000:06: resource 4 mem: [0x000000-0xffffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
pci 0000:01:00.0: Boot video device
Trying to unpack rootfs image as initramfs...
Freeing initrd memory: 20744k freed
PM: Adding info for No Bus:mcelog
PM: Adding info for No Bus:msr0
PM: Adding info for No Bus:msr1
PM: Adding info for platform:pcspkr
PM: Adding info for No Bus:snapshot
highmem bounce pool size: 64 pages
ROMFS MTD (C) 2007 Red Hat, Inc.
msgmni has been set to 1733
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
pcieport 0000:00:02.0: setting latency timer to 64
PM: Adding info for pci_express:0000:00:02.0:pcie08
pcieport 0000:00:04.0: setting latency timer to 64
PM: Adding info for pci_express:0000:00:04.0:pcie08
pcieport 0000:00:05.0: setting latency timer to 64
PM: Adding info for pci_express:0000:00:05.0:pcie08
pcieport 0000:00:06.0: setting latency timer to 64
PM: Adding info for pci_express:0000:00:06.0:pcie08
pcieport 0000:00:07.0: setting latency timer to 64
PM: Adding info for pci_express:0000:00:07.0:pcie08
PM: Adding info for No Bus:pnp1
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
PM: Adding info for No Bus:tty
PM: Adding info for No Bus:console
PM: Adding info for No Bus:tty0
PM: Adding info for No Bus:vcs
PM: Adding info for No Bus:vcsa
PM: Adding info for No Bus:vcs1
PM: Adding info for No Bus:vcsa1
PM: Adding info for No Bus:tty1
PM: Adding info for No Bus:tty2
PM: Adding info for No Bus:tty3
PM: Adding info for No Bus:tty4
PM: Adding info for No Bus:tty5
PM: Adding info for No Bus:tty6
PM: Adding info for No Bus:tty7
PM: Adding info for No Bus:tty8
PM: Adding info for No Bus:tty9
PM: Adding info for No Bus:tty10
PM: Adding info for No Bus:tty11
PM: Adding info for No Bus:tty12
PM: Adding info for No Bus:tty13
PM: Adding info for No Bus:tty14
PM: Adding info for No Bus:tty15
PM: Adding info for No Bus:tty16
PM: Adding info for No Bus:tty17
PM: Adding info for No Bus:tty18
PM: Adding info for No Bus:tty19
PM: Adding info for No Bus:tty20
PM: Adding info for No Bus:tty21
PM: Adding info for No Bus:tty22
PM: Adding info for No Bus:tty23
PM: Adding info for No Bus:tty24
PM: Adding info for No Bus:tty25
PM: Adding info for No Bus:tty26
PM: Adding info for No Bus:tty27
PM: Adding info for No Bus:tty28
PM: Adding info for No Bus:tty29
PM: Adding info for No Bus:tty30
PM: Adding info for No Bus:tty31
PM: Adding info for No Bus:tty32
PM: Adding info for No Bus:tty33
PM: Adding info for No Bus:tty34
PM: Adding info for No Bus:tty35
PM: Adding info for No Bus:tty36
PM: Adding info for No Bus:tty37
PM: Adding info for No Bus:tty38
PM: Adding info for No Bus:tty39
PM: Adding info for No Bus:tty40
PM: Adding info for No Bus:tty41
PM: Adding info for No Bus:tty42
PM: Adding info for No Bus:tty43
PM: Adding info for No Bus:tty44
PM: Adding info for No Bus:tty45
PM: Adding info for No Bus:tty46
PM: Adding info for No Bus:tty47
PM: Adding info for No Bus:tty48
PM: Adding info for No Bus:tty49
PM: Adding info for No Bus:tty50
PM: Adding info for No Bus:tty51
PM: Adding info for No Bus:tty52
PM: Adding info for No Bus:tty53
PM: Adding info for No Bus:tty54
PM: Adding info for No Bus:tty55
PM: Adding info for No Bus:tty56
PM: Adding info for No Bus:tty57
PM: Adding info for No Bus:tty58
PM: Adding info for No Bus:tty59
PM: Adding info for No Bus:tty60
PM: Adding info for No Bus:tty61
PM: Adding info for No Bus:tty62
PM: Adding info for No Bus:tty63
PM: Adding info for No Bus:ptmx
PM: Adding info for No Bus:hpet
PM: Adding info for No Bus:isa
PM: Adding info for No Bus:ram0
PM: Adding info for No Bus:1:0
PM: Adding info for No Bus:ram1
PM: Adding info for No Bus:1:1
PM: Adding info for No Bus:ram2
PM: Adding info for No Bus:1:2
PM: Adding info for No Bus:ram3
PM: Adding info for No Bus:1:3
PM: Adding info for No Bus:ram4
PM: Adding info for No Bus:1:4
PM: Adding info for No Bus:ram5
PM: Adding info for No Bus:1:5
PM: Adding info for No Bus:ram6
PM: Adding info for No Bus:1:6
PM: Adding info for No Bus:ram7
PM: Adding info for No Bus:1:7
PM: Adding info for No Bus:ram8
PM: Adding info for No Bus:1:8
PM: Adding info for No Bus:ram9
PM: Adding info for No Bus:1:9
PM: Adding info for No Bus:ram10
PM: Adding info for No Bus:1:10
PM: Adding info for No Bus:ram11
PM: Adding info for No Bus:1:11
PM: Adding info for No Bus:ram12
PM: Adding info for No Bus:1:12
PM: Adding info for No Bus:ram13
PM: Adding info for No Bus:1:13
PM: Adding info for No Bus:ram14
PM: Adding info for No Bus:1:14
PM: Adding info for No Bus:ram15
PM: Adding info for No Bus:1:15
brd: module loaded
PNP: No PS/2 controller found. Probing ports directly.
PM: Adding info for platform:i8042
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
PM: Adding info for serio:serio0
PM: Adding info for serio:serio1
PM: Adding info for No Bus:mice
PM: Adding info for No Bus:psaux
mice: PS/2 mouse device common for all mice
PM: Adding info for platform:eisa.0
EISA: Probing bus 0 at eisa.0
PM: Removing info for platform:eisa.0
cpuidle: using governor ladder
TCP cubic registered
Using IPI No-Shortcut mode
PM: Adding info for No Bus:cpu_dma_latency
PM: Adding info for No Bus:network_latency
PM: Adding info for No Bus:network_throughput
PM: Checking image partition /dev/hda6
PM: Resume from disk failed.
Magic number: 2:849:937
acpi PNP0103:00: hash matches
Freeing unused kernel memory: 404k freed
NET: Registered protocol family 1
PM: Adding info for No Bus:cooling_device0
fan PNP0C0B:00: registered as cooling_device0
ACPI: Fan [FAN] (on)
PM: Adding info for No Bus:thermal_zone0
thermal LNXTHERM:01: registered as thermal_zone0
ACPI: Thermal Zone [THRM] (40 C)
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17
r8169 0000:06:07.0: PCI INT A -> Link[APC2] -> GSI 17 (level, low) -> IRQ 17
r8169 0000:06:07.0: no PCI Express capability
PM: Adding info for No Bus:eth0
eth0: RTL8169sb/8110sb at 0xf871a000, 00:14:d1:1a:ac:15, XID 10000000 IRQ 17
SCSI subsystem initialized
Uniform Multi-Platform E-IDE driver
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci_hcd: block sizes: ed 64 td 64
ACPI: PCI Interrupt Link [APCF] enabled at IRQ 23
ohci_hcd 0000:00:0b.0: PCI INT A -> Link[APCF] -> GSI 23 (level, low) -> IRQ 23
ohci_hcd 0000:00:0b.0: setting latency timer to 64
ohci_hcd 0000:00:0b.0: OHCI Host Controller
drivers/usb/core/inode.c: creating file 'devices'
drivers/usb/core/inode.c: creating file '001'
ohci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:0b.0: created debug files
ohci_hcd 0000:00:0b.0: supports USB remote wakeup
ohci_hcd 0000:00:0b.0: irq 23, io mem 0xd5006000
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
udev: renamed network interface eth0 to eth1
Warning! ehci_hcd should always be loaded before uhci_hcd and ohci_hcd, not after
ehci_hcd: block sizes: qh 60 qtd 96 itd 160 sitd 96
ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16
ohci1394 0000:06:06.0: PCI INT A -> Link[APC1] -> GSI 16 (level, low) -> IRQ 16
PM: Adding info for ieee1394:fw-host0
PM: Adding info for No Bus:fw-host0
libata version 3.00 loaded.
ohci_hcd 0000:00:0b.0: OHCI controller state
ohci_hcd 0000:00:0b.0: OHCI 1.0, NO legacy support registers
ohci_hcd 0000:00:0b.0: control 0x683 RWE RWC HCFS=operational CBSR=3
ohci_hcd 0000:00:0b.0: cmdstatus 0x00000 SOC=0
ohci_hcd 0000:00:0b.0: intrstatus 0x00000044 RHSC SF
ohci_hcd 0000:00:0b.0: intrenable 0x8000000a MIE RD WDH
ohci_hcd 0000:00:0b.0: hcca frame #0003
ohci_hcd 0000:00:0b.0: roothub.a 01000208 POTPGT=1 NPS NDP=8(8)
ohci_hcd 0000:00:0b.0: roothub.b 00000000 PPCM=0000 DR=0000
ohci_hcd 0000:00:0b.0: roothub.status 00008000 DRWE
ohci_hcd 0000:00:0b.0: roothub.portstatus [0] 0x00010301 CSC LSDA PPS CCS
ohci_hcd 0000:00:0b.0: roothub.portstatus [1] 0x00010101 CSC PPS CCS
ohci_hcd 0000:00:0b.0: roothub.portstatus [2] 0x00010101 CSC PPS CCS
ohci_hcd 0000:00:0b.0: roothub.portstatus [3] 0x00000100 PPS
ohci_hcd 0000:00:0b.0: roothub.portstatus [4] 0x00000100 PPS
ohci_hcd 0000:00:0b.0: roothub.portstatus [5] 0x00010101 CSC PPS CCS
ohci_hcd 0000:00:0b.0: roothub.portstatus [6] 0x00000100 PPS
ohci_hcd 0000:00:0b.0: roothub.portstatus [7] 0x00000100 PPS
usb usb1: default language 0x0409
usb usb1: udev 1, busnum 1, minor = 0
usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: OHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.32testing ohci_hcd
usb usb1: SerialNumber: 0000:00:0b.0
PM: Adding info for usb:usb1
usb usb1: uevent
usb usb1: usb_probe_device
usb usb1: configuration #1 chosen from 1 choice
usb usb1: adding 1-0:1.0 (config #1, interface 0)
PM: Adding info for usb:1-0:1.0
usb 1-0:1.0: uevent
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: no power switching (usb 1.0)
hub 1-0:1.0: global over-current protection
hub 1-0:1.0: power on to power good time: 2ms
hub 1-0:1.0: local power source is good
hub 1-0:1.0: no over-current condition exists
hub 1-0:1.0: trying to enable port power on non-switchable hub
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev1.1
drivers/usb/core/inode.c: creating file '001'
PM: Adding info for No Bus:ep_00
ACPI: PCI Interrupt Link [APCL] enabled at IRQ 22
ehci_hcd 0000:00:0b.1: PCI INT B -> Link[APCL] -> GSI 22 (level, low) -> IRQ 22
ehci_hcd 0000:00:0b.1: setting latency timer to 64
ehci_hcd 0000:00:0b.1: EHCI Host Controller
drivers/usb/core/inode.c: creating file '002'
ehci_hcd 0000:00:0b.1: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:0b.1: reset hcs_params 0x101888 dbg=1 cc=1 pcc=8 !ppc ports=8
ehci_hcd 0000:00:0b.1: reset portroute 0 0 0 0 0 0 0 0
ehci_hcd 0000:00:0b.1: reset hcc_params a086 caching frame 256/512/1024 park
ehci_hcd 0000:00:0b.1: park 0
ehci_hcd 0000:00:0b.1: debug port 1
ehci_hcd 0000:00:0b.1: reset command 080b02 park=3 ithresh=8 period=1024 Reset HALT
ehci_hcd 0000:00:0b.1: cache line size of 32 is not supported
ehci_hcd 0000:00:0b.1: supports USB remote wakeup
ehci_hcd 0000:00:0b.1: irq 22, io mem 0xd5007000
ehci_hcd 0000:00:0b.1: reset command 080b02 park=3 ithresh=8 period=1024 Reset HALT
ehci_hcd 0000:00:0b.1: init command 010009 (park)=0 ithresh=1 period=256 RUN
usb usb1: uevent
usb usb1: uevent
ehci_hcd 0000:00:0b.1: USB 2.0 started, EHCI 1.00
usb usb2: default language 0x0409
usb usb2: udev 1, busnum 2, minor = 128
usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: EHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.32testing ehci_hcd
usb usb2: SerialNumber: 0000:00:0b.1
PM: Adding info for usb:usb2
usb usb2: uevent
usb usb2: usb_probe_device
usb usb2: configuration #1 chosen from 1 choice
usb usb2: adding 2-0:1.0 (config #1, interface 0)
PM: Adding info for usb:2-0:1.0
usb 2-0:1.0: uevent
hub 2-0:1.0: usb_probe_interface
hub 2-0:1.0: usb_probe_interface - got id
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 8 ports detected
hub 2-0:1.0: standalone hub
hub 2-0:1.0: no power switching (usb 1.0)
hub 2-0:1.0: individual port over-current protection
hub 2-0:1.0: power on to power good time: 20ms
hub 2-0:1.0: local power source is good
hub 2-0:1.0: trying to enable port power on non-switchable hub
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev2.1
drivers/usb/core/inode.c: creating file '001'
PM: Adding info for No Bus:ep_00
amd74xx 0000:00:0d.0: UDMA133 controller
amd74xx 0000:00:0d.0: IDE controller (0x10de:0x0265 rev 0xa1)
amd74xx 0000:00:0d.0: IDE port disabled
amd74xx 0000:00:0d.0: BIOS didn't set cable bits correctly. Enabling workaround.
amd74xx 0000:00:0d.0: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xf008-0xf00f
usb usb2: uevent
Probing IDE interface ide0...
usb usb2: uevent
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[16] MMIO=[d4001000-d40017ff] Max Packet=[2] IR/IT contexts=[4/8]
ohci1394: fw-host0: Serial EEPROM has suspicious values, attempting to set max_packet_size to 512 bytes
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00010300 CSC LSDA PPS
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [1] = 0x00010100 CSC PPS
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [2] = 0x00010100 CSC PPS
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [5] = 0x00010100 CSC PPS
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 2-0:1.0: port 1: status 0501 change 0001
ehci_hcd 0000:00:0b.1: GetStatus port 2 status 001803 POWER sig=j CSC CONNECT
hub 2-0:1.0: port 2: status 0501 change 0001
ehci_hcd 0000:00:0b.1: GetStatus port 3 status 001803 POWER sig=j CSC CONNECT
hub 2-0:1.0: port 3: status 0501 change 0001
ehci_hcd 0000:00:0b.1: GetStatus port 6 status 001803 POWER sig=j CSC CONNECT
hub 2-0:1.0: port 6: status 0501 change 0001
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0000
hub 2-0:1.0: state 7 ports 8 chg 004e evt 0000
hub 2-0:1.0: port 1, status 0501, change 0000, 480 Mb/s
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 2-0:1.0: port 2, status 0501, change 0000, 480 Mb/s
ehci_hcd 0000:00:0b.1: port 2 high speed
ehci_hcd 0000:00:0b.1: GetStatus port 2 status 001005 POWER sig=se0 PE CONNECT
usb 2-2: new high speed USB device using ehci_hcd and address 3
ehci_hcd 0000:00:0b.1: port 2 high speed
ehci_hcd 0000:00:0b.1: GetStatus port 2 status 001005 POWER sig=se0 PE CONNECT
usb 2-2: default language 0x0409
usb 2-2: udev 3, busnum 2, minor = 130
usb 2-2: New USB device found, idVendor=058f, idProduct=6362
usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-2: Product: Mass Storage Device
usb 2-2: Manufacturer: Generic
usb 2-2: SerialNumber: 058F312D81B
PM: Adding info for usb:2-2
usb 2-2: uevent
usb 2-2: usb_probe_device
usb 2-2: configuration #1 chosen from 1 choice
usb 2-2: adding 2-2:1.0 (config #1, interface 0)
PM: Adding info for usb:2-2:1.0
usb 2-2:1.0: uevent
PM: Adding info for No Bus:ep_01
PM: Adding info for No Bus:ep_82
PM: Adding info for No Bus:usbdev2.3
drivers/usb/core/inode.c: creating file '003'
PM: Adding info for No Bus:ep_00
hub 2-0:1.0: port 3, status 0501, change 0000, 480 Mb/s
usb 2-2: uevent
usb 2-2: uevent
Initializing USB Mass Storage driver...
usb-storage 2-2:1.0: usb_probe_interface
usb-storage 2-2:1.0: usb_probe_interface - got id
scsi0 : SCSI emulation for USB Mass Storage devices
PM: Adding info for scsi:host0
PM: Adding info for No Bus:host0
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
ehci_hcd 0000:00:0b.1: port 3 high speed
ehci_hcd 0000:00:0b.1: GetStatus port 3 status 001005 POWER sig=se0 PE CONNECT
usb 2-3: new high speed USB device using ehci_hcd and address 4
ehci_hcd 0000:00:0b.1: port 3 high speed
ehci_hcd 0000:00:0b.1: GetStatus port 3 status 001005 POWER sig=se0 PE CONNECT
hda: PIONEER DVD-RW DVR-111D, ATAPI CD/DVD-ROM drive
usb 2-3: default language 0x0409
usb 2-3: udev 4, busnum 2, minor = 131
usb 2-3: New USB device found, idVendor=05e3, idProduct=0605
usb 2-3: New USB device strings: Mfr=0, Product=1, SerialNumber=0
usb 2-3: Product: USB2.0 Hub
PM: Adding info for usb:2-3
usb 2-3: uevent
usb 2-3: usb_probe_device
usb 2-3: configuration #1 chosen from 1 choice
usb 2-3: adding 2-3:1.0 (config #1, interface 0)
PM: Adding info for usb:2-3:1.0
usb 2-3:1.0: uevent
hub 2-3:1.0: usb_probe_interface
hub 2-3:1.0: usb_probe_interface - got id
hub 2-3:1.0: USB hub found
hub 2-3:1.0: 4 ports detected
hub 2-3:1.0: standalone hub
hub 2-3:1.0: individual port power switching
hub 2-3:1.0: individual port over-current protection
hub 2-3:1.0: Single TT
hub 2-3:1.0: TT requires at most 32 FS bit times (2664 ns)
hub 2-3:1.0: Port indicators are supported
hub 2-3:1.0: power on to power good time: 100ms
usb 2-3: uevent
hub 2-3:1.0: local power source is good
hub 2-3:1.0: enabling power on all ports
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev2.4
drivers/usb/core/inode.c: creating file '004'
PM: Adding info for No Bus:ep_00
hub 2-0:1.0: port 6, status 0501, change 0000, 480 Mb/s
usb 2-3: uevent
ehci_hcd 0000:00:0b.1: port 6 high speed
ehci_hcd 0000:00:0b.1: GetStatus port 6 status 001005 POWER sig=se0 PE CONNECT
hub 2-3:1.0: port 1: status 0101 change 0001
usb 2-6: new high speed USB device using ehci_hcd and address 5
ehci_hcd 0000:00:0b.1: port 6 high speed
ehci_hcd 0000:00:0b.1: GetStatus port 6 status 001005 POWER sig=se0 PE CONNECT
usb 2-3: link qh256-0001/c210dec0 start 1 [1/0 us]
usb 2-6: udev 5, busnum 2, minor = 132
usb 2-6: New USB device found, idVendor=0409, idProduct=0059
usb 2-6: New USB device strings: Mfr=0, Product=0, SerialNumber=0
PM: Adding info for usb:2-6
usb 2-6: uevent
usb 2-6: usb_probe_device
usb 2-6: configuration #1 chosen from 1 choice
usb 2-6: adding 2-6:1.0 (config #1, interface 0)
PM: Adding info for usb:2-6:1.0
usb 2-6:1.0: uevent
hub 2-6:1.0: usb_probe_interface
hub 2-6:1.0: usb_probe_interface - got id
hub 2-6:1.0: USB hub found
hub 2-6:1.0: 4 ports detected
hub 2-6:1.0: standalone hub
hub 2-6:1.0: individual port power switching
hub 2-6:1.0: individual port over-current protection
hub 2-6:1.0: Single TT
hub 2-6:1.0: TT requires at most 16 FS bit times (1332 ns)
hub 2-6:1.0: Port indicators are supported
hub 2-6:1.0: power on to power good time: 100ms
usb 2-6: uevent
hub 2-6:1.0: local power source is good
hub 2-6:1.0: enabling power on all ports
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev2.5
usb 2-6: uevent
drivers/usb/core/inode.c: creating file '005'
PM: Adding info for No Bus:ep_00
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00010301 CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0001, 1.5 Mb/s
hub 2-6:1.0: port 1: status 0301 change 0001
hub 2-6:1.0: port 3: status 0101 change 0001
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130301 PRSC PESC CSC LSDA PPS CCS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-3:1.0: state 7 ports 4 chg 0002 evt 0000
hub 2-3:1.0: port 1, status 0101, change 0000, 12 Mb/s
usb 2-6: link qh256-0001/c1cabd40 start 2 [1/0 us]
usb 2-3.1: new high speed USB device using ehci_hcd and address 6
usb 2-3.1: udev 6, busnum 2, minor = 133
usb 2-3.1: New USB device found, idVendor=0409, idProduct=0059
usb 2-3.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
PM: Adding info for usb:2-3.1
usb 2-3.1: uevent
usb 2-3.1: usb_probe_device
usb 2-3.1: configuration #1 chosen from 1 choice
usb 2-3.1: adding 2-3.1:1.0 (config #1, interface 0)
PM: Adding info for usb:2-3.1:1.0
usb 2-3.1:1.0: uevent
hub 2-3.1:1.0: usb_probe_interface
hub 2-3.1:1.0: usb_probe_interface - got id
hub 2-3.1:1.0: USB hub found
hub 2-3.1:1.0: 4 ports detected
hub 2-3.1:1.0: standalone hub
hub 2-3.1:1.0: individual port power switching
hub 2-3.1:1.0: individual port over-current protection
hub 2-3.1:1.0: Single TT
hub 2-3.1:1.0: TT requires at most 16 FS bit times (1332 ns)
hub 2-3.1:1.0: Port indicators are supported
hub 2-3.1:1.0: power on to power good time: 100ms
hub 2-3.1:1.0: local power source is good
hub 2-3.1:1.0: enabling power on all ports
usb 2-3.1: uevent
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev2.6
drivers/usb/core/inode.c: creating file '006'
PM: Adding info for No Bus:ep_00
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
usb 2-3.1: uevent
PM: Adding info for ieee1394:001106000000bd66
PM: Adding info for No Bus:001106000000bd66
ieee1394: Host added: ID:BUS[0-00:1023] GUID[001106000000bd66]
PM: Adding info for No Bus:ide0
PM: Adding info for No Bus:ide0
hda: host max PIO5 wanted PIO255(auto-tune) selected PIO4
hda: UDMA/66 mode selected
ide0 at 0x170-0x177,0x376 on irq 15
PM: Adding info for ieee1394:001a66fffee31809
PM: Adding info for No Bus:001a66fffee31809
ieee1394: Node added: ID:BUS[0-01:1023] GUID[001a66fffee31809]
PM: Adding info for ieee1394:001a66fffee31809-0
PM: Adding info for No Bus:001a66fffee31809-0
PM: Adding info for ieee1394:001a66fffee31809-1
PM: Adding info for No Bus:001a66fffee31809-1
PM: Adding info for ide:0.0
sata_nv 0000:00:0e.0: version 3.5
ACPI: PCI Interrupt Link [APSI] enabled at IRQ 21
sata_nv 0000:00:0e.0: PCI INT A -> Link[APSI] -> GSI 21 (level, low) -> IRQ 21
sata_nv 0000:00:0e.0: Using SWNCQ mode
sata_nv 0000:00:0e.0: setting latency timer to 64
scsi1 : sata_nv
PM: Adding info for scsi:host1
PM: Adding info for No Bus:host1
scsi2 : sata_nv
PM: Adding info for scsi:host2
PM: Adding info for No Bus:host2
ata1: SATA max UDMA/133 cmd 0x9f0 ctl 0xbf0 bmdma 0xd400 irq 21
ata2: SATA max UDMA/133 cmd 0x970 ctl 0xb70 bmdma 0xd408 irq 21
ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 20
sata_nv 0000:00:0f.0: PCI INT A -> Link[APSJ] -> GSI 20 (level, low) -> IRQ 20
sata_nv 0000:00:0f.0: Using SWNCQ mode
sata_nv 0000:00:0f.0: setting latency timer to 64
scsi3 : sata_nv
PM: Adding info for scsi:host3
PM: Adding info for No Bus:host3
scsi4 : sata_nv
PM: Adding info for scsi:host4
PM: Adding info for No Bus:host4
ata3: SATA max UDMA/133 cmd 0x9e0 ctl 0xbe0 bmdma 0xe800 irq 20
ata4: SATA max UDMA/133 cmd 0x960 ctl 0xb60 bmdma 0xe808 irq 20
hub 2-3.1:1.0: port 1: status 0301 change 0001
hub 2-3.1:1.0: port 2: status 0101 change 0001
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-6:1.0: state 7 ports 4 chg 000a evt 0000
hub 2-6:1.0: port 1, status 0301, change 0000, 1.5 Mb/s
hub 2-6:1.0: port 1 not reset yet, waiting 10ms
usb 2-3.1: link qh256-0001/c1e4a5c0 start 3 [1/0 us]
usb 2-6.1: new low speed USB device using ehci_hcd and address 7
hub 2-6:1.0: port 1 not reset yet, waiting 10ms
usb 2-6.1: skipped 1 descriptor after interface
usb 2-6.1: default language 0x0409
usb 2-6.1: udev 7, busnum 2, minor = 134
usb 2-6.1: New USB device found, idVendor=2222, idProduct=3100
usb 2-6.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 2-6.1: Product: Macally ECOMouse
usb 2-6.1: Manufacturer: Macally Peripherals
PM: Adding info for usb:2-6.1
usb 2-6.1: uevent
usb 2-6.1: usb_probe_device
usb 2-6.1: configuration #1 chosen from 1 choice
usb 2-6.1: adding 2-6.1:1.0 (config #1, interface 0)
PM: Adding info for usb:2-6.1:1.0
usb 2-6.1:1.0: uevent
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev2.7
drivers/usb/core/inode.c: creating file '007'
PM: Adding info for No Bus:ep_00
hub 2-6:1.0: port 3, status 0101, change 0000, 12 Mb/s
usb 2-6.1: uevent
usb 2-6.1: uevent
usbcore: registered new interface driver hiddev
usbhid 2-6.1:1.0: usb_probe_interface
usbhid 2-6.1:1.0: usb_probe_interface - got id
PM: Adding info for hid:0003:2222:3100.0001
PM: Adding info for No Bus:input0
input: Macally Peripherals Macally ECOMouse as /devices/pci0000:00/0000:00:0b.1/usb2/2-6/2-6.1/2-6.1:1.0/input/input0
PM: Adding info for No Bus:mouse0
generic-usb 0003:2222:3100.0001: input: USB HID v1.00 Mouse [Macally Peripherals Macally ECOMouse ] on usb-0000:00:0b.1-6.1/input0
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
hub 2-6:1.0: port 3 not reset yet, waiting 10ms
ata3: SATA link down (SStatus 0 SControl 300)
usb 2-6.3: new full speed USB device using ehci_hcd and address 8
hub 2-6:1.0: port 3 not reset yet, waiting 10ms
usb 2-6.3: ep0 maxpacket = 8
usb 2-6.3: default language 0x0409
usb 2-6.3: udev 8, busnum 2, minor = 135
usb 2-6.3: New USB device found, idVendor=05e3, idProduct=0604
usb 2-6.3: New USB device strings: Mfr=0, Product=1, SerialNumber=0
usb 2-6.3: Product: USB Hub
PM: Adding info for usb:2-6.3
usb 2-6.3: uevent
usb 2-6.3: usb_probe_device
usb 2-6.3: configuration #1 chosen from 1 choice
usb 2-6.3: adding 2-6.3:1.0 (config #1, interface 0)
PM: Adding info for usb:2-6.3:1.0
usb 2-6.3:1.0: uevent
hub 2-6.3:1.0: usb_probe_interface
hub 2-6.3:1.0: usb_probe_interface - got id
hub 2-6.3:1.0: USB hub found
usb 2-6.3: uevent
hub 2-6.3:1.0: 4 ports detected
hub 2-6.3:1.0: standalone hub
hub 2-6.3:1.0: individual port power switching
hub 2-6.3:1.0: individual port over-current protection
hub 2-6.3:1.0: power on to power good time: 100ms
hub 2-6.3:1.0: local power source is good
hub 2-6.3:1.0: enabling power on all ports
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev2.8
drivers/usb/core/inode.c: creating file '008'
PM: Adding info for No Bus:ep_00
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030300 PESC CSC LSDA PPS
hub 1-0:1.0: port 1, status 0300, change 0003, 1.5 Mb/s
usb 2-6.3: uevent
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
hub 2-6.3:1.0: port 3: status 0301 change 0001
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x300
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 2-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
ata1.00: ATA-7: SAMSUNG SP2504C, VT100-41, max UDMA7
ata1.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata1.00: configured for UDMA/133
scsi 1:0:0:0: Direct-Access ATA SAMSUNG SP2504C VT10 PQ: 0 ANSI: 5
PM: Adding info for scsi:target1:0:0
PM: Adding info for scsi:1:0:0:0
PM: Adding info for No Bus:1:0:0:0
PM: Adding info for No Bus:1:0:0:0
usb 2-6.3: link qh128-0e01/c1e81140 start 4 [1/2 us]
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 2-3.1:1.0: state 7 ports 4 chg 0006 evt 0000
hub 2-3.1:1.0: port 1, status 0301, change 0000, 1.5 Mb/s
hub 2-3.1:1.0: port 1 not reset yet, waiting 10ms
usb 2-3.1.1: new low speed USB device using ehci_hcd and address 10
hub 2-3.1:1.0: port 1 not reset yet, waiting 10ms
usb 2-3.1.1: skipped 1 descriptor after interface
usb 2-3.1.1: skipped 1 descriptor after interface
usb 2-3.1.1: default language 0x0409
usb 2-3.1.1: udev 10, busnum 2, minor = 137
usb 2-3.1.1: New USB device found, idVendor=10d5, idProduct=0004
usb 2-3.1.1: New USB device strings: Mfr=0, Product=2, SerialNumber=0
usb 2-3.1.1: Product: PS2 to USB AdapterA3
PM: Adding info for usb:2-3.1.1
usb 2-3.1.1: uevent
usb 2-3.1.1: usb_probe_device
usb 2-3.1.1: configuration #1 chosen from 1 choice
usb 2-3.1.1: uevent
usb 2-3.1.1: adding 2-3.1.1:1.0 (config #1, interface 0)
PM: Adding info for usb:2-3.1.1:1.0
usb 2-3.1.1:1.0: uevent
usbhid 2-3.1.1:1.0: usb_probe_interface
usbhid 2-3.1.1:1.0: usb_probe_interface - got id
PM: Adding info for hid:0003:10D5:0004.0002
PM: Adding info for No Bus:input1
input: PS2 to USB AdapterA3 as /devices/pci0000:00/0000:00:0b.1/usb2/2-3/2-3.1/2-3.1.1/2-3.1.1:1.0/input/input1
usb 2-3.1.1: link qh8-0e01/c1e81440 start 5 [1/2 us]
generic-usb 0003:10D5:0004.0002: input: USB HID v1.10 Keyboard [PS2 to USB AdapterA3] on usb-0000:00:0b.1-3.1.1/input0
PM: Adding info for No Bus:ep_81
usb 2-3.1.1: adding 2-3.1.1:1.1 (config #1, interface 1)
PM: Adding info for usb:2-3.1.1:1.1
usb 2-3.1.1:1.1: uevent
usbhid 2-3.1.1:1.1: usb_probe_interface
usbhid 2-3.1.1:1.1: usb_probe_interface - got id
PM: Adding info for hid:0003:10D5:0004.0003
PM: Adding info for No Bus:input2
input: PS2 to USB AdapterA3 as /devices/pci0000:00/0000:00:0b.1/usb2/2-3/2-3.1/2-3.1.1/2-3.1.1:1.1/input/input2
usb 2-3.1.1: link qh8-0e01/c1e81540 start 6 [1/2 us]
PM: Adding info for No Bus:mouse1
generic-usb 0003:10D5:0004.0003: input: USB HID v1.10 Mouse [PS2 to USB AdapterA3] on usb-0000:00:0b.1-3.1.1/input1
PM: Adding info for No Bus:ep_82
PM: Adding info for No Bus:usbdev2.10
drivers/usb/core/inode.c: creating file '010'
PM: Adding info for No Bus:ep_00
usb 2-3.1.1: uevent
hub 2-3.1:1.0: port 2, status 0101, change 0000, 12 Mb/s
hub 2-3.1:1.0: port 2 not reset yet, waiting 10ms
usb 2-3.1.2: new high speed USB device using ehci_hcd and address 11
hub 2-3.1:1.0: port 2 not reset yet, waiting 10ms
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
usb 2-3.1.2: default language 0x0409
usb 2-3.1.2: udev 11, busnum 2, minor = 138
usb 2-3.1.2: New USB device found, idVendor=05e3, idProduct=0605
usb 2-3.1.2: New USB device strings: Mfr=0, Product=1, SerialNumber=0
usb 2-3.1.2: Product: USB2.0 Hub
PM: Adding info for usb:2-3.1.2
usb 2-3.1.2: uevent
usb 2-3.1.2: usb_probe_device
usb 2-3.1.2: configuration #1 chosen from 1 choice
usb 2-3.1.2: adding 2-3.1.2:1.0 (config #1, interface 0)
PM: Adding info for usb:2-3.1.2:1.0
usb 2-3.1.2:1.0: uevent
hub 2-3.1.2:1.0: usb_probe_interface
hub 2-3.1.2:1.0: usb_probe_interface - got id
hub 2-3.1.2:1.0: USB hub found
hub 2-3.1.2:1.0: 4 ports detected
hub 2-3.1.2:1.0: standalone hub
hub 2-3.1.2:1.0: individual port power switching
hub 2-3.1.2:1.0: individual port over-current protection
hub 2-3.1.2:1.0: Single TT
hub 2-3.1.2:1.0: TT requires at most 32 FS bit times (2664 ns)
hub 2-3.1.2:1.0: Port indicators are supported
hub 2-3.1.2:1.0: power on to power good time: 100ms
usb 2-3.1.2: uevent
hub 2-3.1.2:1.0: local power source is good
hub 2-3.1.2:1.0: enabling power on all ports
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev2.11
drivers/usb/core/inode.c: creating file '011'
PM: Adding info for No Bus:ep_00
hub 2-6:1.0: state 7 ports 4 chg 0000 evt 0002
usb 2-3.1.2: uevent
hub 2-6.3:1.0: state 7 ports 4 chg 0008 evt 0000
hub 2-6.3:1.0: port 3, status 0301, change 0000, 1.5 Mb/s
ata2.00: ATA-7: ST3250620AS, 3.AAC, max UDMA/133
ata2.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32)
usb 2-6.3.3: new low speed USB device using ehci_hcd and address 12
hub 2-6.3:1.0: port 3 not reset yet, waiting 10ms
hub 2-3.1.2:1.0: port 1: status 0101 change 0001
hub 2-3.1.2:1.0: port 2: status 0301 change 0001
ata2.00: configured for UDMA/133
scsi 2:0:0:0: Direct-Access ATA ST3250620AS 3.AA PQ: 0 ANSI: 5
PM: Adding info for scsi:target2:0:0
PM: Adding info for scsi:2:0:0:0
PM: Adding info for No Bus:2:0:0:0
PM: Adding info for No Bus:2:0:0:0
usb 2-6.3.3: skipped 1 descriptor after interface
usb 2-6.3.3: skipped 1 descriptor after interface
usb 2-6.3.3: default language 0x0409
usb 2-6.3.3: udev 12, busnum 2, minor = 139
usb 2-6.3.3: New USB device found, idVendor=2222, idProduct=0013
usb 2-6.3.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 2-6.3.3: Product: Macally iKeySlim
usb 2-6.3.3: Manufacturer: Macally Peripherals
PM: Adding info for usb:2-6.3.3
usb 2-6.3.3: uevent
usb 2-6.3.3: usb_probe_device
usb 2-6.3.3: configuration #1 chosen from 1 choice
usb 2-6.3.3: uevent
usb 2-6.3.3: adding 2-6.3.3:1.0 (config #1, interface 0)
PM: Adding info for usb:2-6.3.3:1.0
usb 2-6.3.3:1.0: uevent
usbhid 2-6.3.3:1.0: usb_probe_interface
usbhid 2-6.3.3:1.0: usb_probe_interface - got id
PM: Adding info for hid:0003:2222:0013.0004
PM: Adding info for No Bus:input3
input: Macally Peripherals Macally iKeySlim as /devices/pci0000:00/0000:00:0b.1/usb2/2-6/2-6.3/2-6.3.3/2-6.3.3:1.0/input/input3
usb 2-6.3.3: link qh8-0e01/c1e81a00 start 7 [1/2 us]
generic-usb 0003:2222:0013.0004: input: USB HID v1.10 Keyboard [Macally Peripherals Macally iKeySlim] on usb-0000:00:0b.1-6.3.3/input0
PM: Adding info for No Bus:ep_81
usb 2-6.3.3: adding 2-6.3.3:1.1 (config #1, interface 1)
PM: Adding info for usb:2-6.3.3:1.1
usb 2-6.3.3:1.1: uevent
usbhid 2-6.3.3:1.1: usb_probe_interface
usbhid 2-6.3.3:1.1: usb_probe_interface - got id
PM: Adding info for hid:0003:2222:0013.0005
PM: Adding info for No Bus:input4
input: Macally Peripherals Macally iKeySlim as /devices/pci0000:00/0000:00:0b.1/usb2/2-6/2-6.3/2-6.3.3/2-6.3.3:1.1/input/input4
usb 2-6.3.3: link qh8-0e01/c1e81b40 start 0 [1/2 us]
PM: Adding info for No Bus:mouse2
generic-usb 0003:2222:0013.0005: input: USB HID v1.10 Mouse [Macally Peripherals Macally iKeySlim] on usb-0000:00:0b.1-6.3.3/input1
PM: Adding info for No Bus:ep_82
PM: Adding info for No Bus:usbdev2.12
drivers/usb/core/inode.c: creating file '012'
PM: Adding info for No Bus:ep_00
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00010301 CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0001, 1.5 Mb/s
usb 2-6.3.3: uevent
usb 2-3.1.2: link qh256-0001/c1e81bc0 start 9 [1/0 us]
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-3.1:1.0: state 7 ports 4 chg 0000 evt 0004
hub 2-6.3:1.0: state 7 ports 4 chg 0000 evt 0008
hub 2-3.1.2:1.0: state 7 ports 4 chg 0006 evt 0000
hub 2-3.1.2:1.0: port 1, status 0101, change 0000, 12 Mb/s
usb 2-3.1.2.1: new high speed USB device using ehci_hcd and address 13
hub 2-3.1.2:1.0: port 1 not reset yet, waiting 10ms
usb 2-3.1.2.1: default language 0x0409
usb 2-3.1.2.1: udev 13, busnum 2, minor = 140
usb 2-3.1.2.1: New USB device found, idVendor=090c, idProduct=1000
usb 2-3.1.2.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-3.1.2.1: Product: DISK 2.0
usb 2-3.1.2.1: Manufacturer: USB
usb 2-3.1.2.1: SerialNumber: PHN84K6AD8PLXSVC
PM: Adding info for usb:2-3.1.2.1
usb 2-3.1.2.1: uevent
usb 2-3.1.2.1: usb_probe_device
usb 2-3.1.2.1: configuration #1 chosen from 1 choice
usb 2-3.1.2.1: adding 2-3.1.2.1:1.0 (config #1, interface 0)
PM: Adding info for usb:2-3.1.2.1:1.0
usb 2-3.1.2.1:1.0: uevent
usb-storage 2-3.1.2.1:1.0: usb_probe_interface
usb-storage 2-3.1.2.1:1.0: usb_probe_interface - got id
scsi5 : SCSI emulation for USB Mass Storage devices
PM: Adding info for scsi:host5
PM: Adding info for No Bus:host5
usb-storage: device found at 13
usb-storage: waiting for device to settle before scanning
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:ep_02
PM: Adding info for No Bus:usbdev2.13
drivers/usb/core/inode.c: creating file '013'
PM: Adding info for No Bus:ep_00
usb 2-3.1.2.1: uevent
usb 2-3.1.2.1: uevent
hub 2-3.1.2:1.0: port 2, status 0301, change 0000, 1.5 Mb/s
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: ATAPI: ATAPI iHOS104, WL08, max UDMA/100
usb 2-3.1.2.2: new low speed USB device using ehci_hcd and address 14
ata4.00: configured for UDMA/100
hub 2-3.1.2:1.0: port 2 not reset yet, waiting 10ms
scsi 4:0:0:0: CD-ROM ATAPI iHOS104 WL08 PQ: 0 ANSI: 5
PM: Adding info for scsi:target4:0:0
PM: Adding info for scsi:4:0:0:0
PM: Adding info for No Bus:4:0:0:0
PM: Adding info for No Bus:4:0:0:0
PM: Adding info for No Bus:1:0:0:0
sd 1:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
PM: Adding info for No Bus:sda
sda:
PM: Adding info for No Bus:2:0:0:0
sd 2:0:0:0: [sdb] 488397168 512-byte logical blocks: (250 GB/232 GiB)
sd 2:0:0:0: [sdb] Write Protect is off
sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
PM: Adding info for No Bus:sdb
sdb: sda1 sda2 sda3 < >
PM: Adding info for No Bus:sda1
PM: Adding info for No Bus:sda2
PM: Adding info for No Bus:sda3
PM: Adding info for No Bus:8:0
unknown partition table
PM: Adding info for No Bus:8:16
sd 2:0:0:0: [sdb] Attached SCSI disk
sd 1:0:0:0: [sda] Attached SCSI disk
ide-cd driver 5.00
PM: Adding info for No Bus:0.0
ide-cd: hda: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2000kB Cache
Uniform CD-ROM driver Revision: 3.20
usb 2-3.1.2.2: skipped 1 descriptor after interface
usb 2-3.1.2.2: default language 0x0409
usb 2-3.1.2.2: udev 14, busnum 2, minor = 141
usb 2-3.1.2.2: New USB device found, idVendor=046d, idProduct=c050
usb 2-3.1.2.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 2-3.1.2.2: Product: USB-PS/2 Optical Mouse
usb 2-3.1.2.2: Manufacturer: Logitech
PM: Adding info for usb:2-3.1.2.2
usb 2-3.1.2.2: uevent
usb 2-3.1.2.2: usb_probe_device
usb 2-3.1.2.2: configuration #1 chosen from 1 choice
usb 2-3.1.2.2: adding 2-3.1.2.2:1.0 (config #1, interface 0)
PM: Adding info for usb:2-3.1.2.2:1.0
usb 2-3.1.2.2:1.0: uevent
usbhid 2-3.1.2.2:1.0: usb_probe_interface
usbhid 2-3.1.2.2:1.0: usb_probe_interface - got id
PM: Adding info for hid:0003:046D:C050.0006
usb 2-3.1.2.2: uevent
PM: Adding info for No Bus:input5
input: Logitech USB-PS/2 Optical Mouse as /devices/pci0000:00/0000:00:0b.1/usb2/2-3/2-3.1/2-3.1.2/2-3.1.2.2/2-3.1.2.2:1.0/input/input5
PM: Adding info for No Bus:mouse3
generic-usb 0003:046D:C050.0006: input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:0b.1-3.1.2.2/input0
PM: Adding info for No Bus:ep_81
PM: Adding info for No Bus:usbdev2.14
drivers/usb/core/inode.c: creating file '014'
PM: Adding info for No Bus:ep_00
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 2-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
usb 2-3.1.2.2: uevent
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
PM: Adding info for No Bus:device-mapper
device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
PM: Adding info for No Bus:dm-0
PM: Adding info for No Bus:254:0
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
PM: Adding info for No Bus:dm-1
PM: Adding info for No Bus:254:1
PM: Adding info for No Bus:dm-2
PM: Adding info for No Bus:254:2
PM: Adding info for No Bus:dm-3
PM: Adding info for No Bus:254:3
PM: Adding info for No Bus:dm-4
PM: Adding info for No Bus:254:4
PM: Adding info for No Bus:dm-5
PM: Adding info for No Bus:254:5
PM: Adding info for No Bus:dm-6
PM: Adding info for No Bus:254:6
PM: Removing info for No Bus:254:3
PM: Removing info for No Bus:dm-3
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 2-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
PM: Adding info for No Bus:hda
PM: Adding info for No Bus:3:0
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
xor: automatically using best checksumming function: pIII_sse
pIII_sse : 7516.000 MB/sec
xor: using function: pIII_sse (7516.000 MB/sec)
raid6: int32x1 878 MB/s
raid6: int32x2 839 MB/s
raid6: int32x4 703 MB/s
raid6: int32x8 585 MB/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
raid6: mmxx1 2742 MB/s
raid6: mmxx2 3167 MB/s
raid6: sse1x1 1890 MB/s
raid6: sse1x2 2441 MB/s
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 2-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
raid6: sse2x1 3542 MB/s
raid6: sse2x2 4226 MB/s
raid6: using algorithm sse2x2 (4226 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
md: raid10 personality registered for level 10
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
PM: Marking nosave pages: 000000000009c000 - 0000000000100000
PM: Basic memory bitmaps created
PM: Basic memory bitmaps freed
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with writeback data mode.
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 2-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 2-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 2-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 2-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 2-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
scsi 0:0:0:0: Direct-Access Generic USB SD Reader 1.00 PQ: 0 ANSI: 0
PM: Adding info for scsi:target0:0:0
PM: Adding info for scsi:0:0:0:0
PM: Adding info for No Bus:0:0:0:0
PM: Adding info for No Bus:0:0:0:0
PM: Adding info for No Bus:0:0:0:0
scsi 0:0:0:1: Direct-Access Generic USB CF Reader 1.01 PQ: 0 ANSI: 0
PM: Adding info for scsi:0:0:0:1
PM: Adding info for No Bus:0:0:0:1
PM: Adding info for No Bus:0:0:0:1
PM: Adding info for No Bus:0:0:0:1
PM: Adding info for No Bus:sdc
PM: Adding info for No Bus:8:32
PM: Adding info for No Bus:sdd
PM: Adding info for No Bus:8:48
scsi 0:0:0:2: Direct-Access Generic USB SM Reader 1.02 PQ: 0 ANSI: 0
PM: Adding info for scsi:0:0:0:2
PM: Adding info for No Bus:0:0:0:2
PM: Adding info for No Bus:0:0:0:2
PM: Adding info for No Bus:0:0:0:2
sd 0:0:0:0: [sdc] Attached SCSI removable disk
sd 0:0:0:1: [sdd] Attached SCSI removable disk
PM: Adding info for No Bus:sde
PM: Adding info for No Bus:8:64
scsi 0:0:0:3: Direct-Access Generic USB MS Reader 1.03 PQ: 0 ANSI: 0
PM: Adding info for scsi:0:0:0:3
PM: Adding info for No Bus:0:0:0:3
PM: Adding info for No Bus:0:0:0:3
PM: Adding info for No Bus:0:0:0:3
sd 0:0:0:2: [sde] Attached SCSI removable disk
PM: Adding info for No Bus:sdf
PM: Adding info for No Bus:8:80
sd 0:0:0:3: [sdf] Attached SCSI removable disk
usb-storage: device scan complete
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 2-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 2-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 2-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
udev: starting version 146
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
usb usb1: uevent
usb 1-0:1.0: uevent
usb usb2: uevent
usb 2-0:1.0: uevent
usb 2-2: uevent
usb 2-2:1.0: uevent
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
usb 2-3: uevent
usb 2-3.1: uevent
usb 2-3.1.1: uevent
usb 2-3.1.1:1.0: uevent
usb 2-3.1.1:1.1: uevent
usb 2-3.1.2: uevent
usb 2-3.1.2.1: uevent
usb 2-3.1.2.1:1.0: uevent
usb 2-3.1.2.2: uevent
usb 2-3.1.2.2:1.0: uevent
usb 2-3.1.2:1.0: uevent
usb 2-3.1:1.0: uevent
usb 2-3:1.0: uevent
usb 2-6: uevent
usb 2-6.1: uevent
usb 2-6.1:1.0: uevent
usb 2-6.3: uevent
usb 2-6.3.3: uevent
usb 2-6.3.3:1.0: uevent
usb 2-6.3.3:1.1: uevent
usb 2-6.3:1.0: uevent
usb 2-6:1.0: uevent
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 2-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
usb usb2: uevent
usb usb1: uevent
usb usb2: uevent
usb usb1: uevent
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
usb 2-2: uevent
usb 2-3: uevent
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
usb 2-6: uevent
usb 2-3: uevent
usb 2-2:1.0: uevent
usb 2-2: uevent
usb 2-2:1.0: uevent
usb 2-2: uevent
usb 2-2:1.0: uevent
usb 2-2: uevent
usb 2-2: uevent
usb 2-2:1.0: uevent
usb 2-2: uevent
usb 2-6: uevent
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 2-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
usb 2-2:1.0: uevent
usb 2-2:1.0: uevent
usb 2-2:1.0: uevent
usb 2-2:1.0: uevent
usb 2-3.1: uevent
usb 2-6.3: uevent
usb 2-6.1: uevent
usb 2-3.1: uevent
usb 2-6.3: uevent
usb 2-6.1: uevent
usb 2-3.1.2: uevent
usb 2-3.1.2: uevent
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
usb 2-6.3.3: uevent
usb 2-3.1.1: uevent
usb 2-6.3.3: uevent
usb 2-3.1.2.1: uevent
usb 2-3.1.1: uevent
usb 2-3.1.2.2: uevent
usb 2-3.1.2.1: uevent
usb 2-3.1.2.2: uevent
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 2-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
ACPI: SSDT 7fefa940 00175 (v01 Nvidia ASUSACPI 42302E31 AWRD 00000000)
PM: Adding info for No Bus:cooling_device1
processor LNXCPU:00: registered as cooling_device1
ACPI: SSDT 7fefad50 000CE (v01 Nvidia ASUSACPI 42302E31 AWRD 00000000)
PM: Adding info for No Bus:cooling_device2
processor LNXCPU:01: registered as cooling_device2
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
PM: Adding info for No Bus:input6
input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input6
ACPI: Power Button [PWRB]
PM: Adding info for No Bus:input7
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input7
ACPI: Power Button [PWRF]
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
PM: Adding info for No Bus:rtc
Real Time Clock Driver v1.12b
PM: Adding info for No Bus:hwmon0
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 2-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
PM: Adding info for No Bus:event0
PM: Adding info for No Bus:event1
PM: Adding info for No Bus:event2
PM: Adding info for No Bus:event3
PM: Adding info for No Bus:event4
PM: Adding info for No Bus:event5
PM: Adding info for No Bus:event6
PM: Adding info for No Bus:event7
usb 2-3.1.2.2:1.0: uevent
usb 2-3.1.2.2: uevent
usb 2-3.1.2.2:1.0: uevent
usb 2-3.1.2.2:1.0: uevent
usb 2-3.1.2.2: uevent
usb 2-3.1.2.2:1.0: uevent
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
PM: Adding info for No Bus:raw1394
ieee1394: raw1394: /dev/raw1394 device initialized
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 2-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
scsi 5:0:0:0: Direct-Access USB DISK 2.0 0403 PQ: 0 ANSI: 0 CCS
PM: Adding info for scsi:target5:0:0
PM: Adding info for scsi:5:0:0:0
PM: Adding info for No Bus:5:0:0:0
PM: Adding info for No Bus:5:0:0:0
PM: Adding info for No Bus:5:0:0:0
sd 5:0:0:0: [sdg] 3981312 512-byte logical blocks: (2.03 GB/1.89 GiB)
sd 5:0:0:0: [sdg] Write Protect is off
sd 5:0:0:0: [sdg] Mode Sense: 43 00 00 00
sd 5:0:0:0: [sdg] Assuming drive cache: write through
usb-storage: device scan complete
PM: Adding info for No Bus:sdg
sd 5:0:0:0: [sdg] Assuming drive cache: write through
sdg: sdg1
PM: Adding info for No Bus:sdg1
PM: Adding info for No Bus:8:96
sd 5:0:0:0: [sdg] Assuming drive cache: write through
sd 5:0:0:0: [sdg] Attached SCSI removable disk
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
sr0: scsi3-mmc drive: 62x/62x cd/rw xa/form2 cdda tray
PM: Adding info for No Bus:sr0
PM: Adding info for No Bus:11:0
sr 4:0:0:0: Attached scsi CD-ROM sr0
ACPI: I/O resource nForce2_smbus [0x5000-0x503f] conflicts with ACPI region SM00 [0x5000-0x5005]
ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
nForce2_smbus 0000:00:0a.1: Error probing SMB1.
PM: Adding info for i2c:i2c-0
i2c i2c-0: nForce2 SMBus adapter at 0x5100
usb 2-6.1:1.0: uevent
usb 2-6.1: uevent
usb 2-3.1.1:1.1: uevent
usb 2-3.1.1: uevent
usb 2-3.1.1:1.1: uevent
usb 2-3.1.1: uevent
usb 2-6.3.3:1.0: uevent
usb 2-6.1:1.0: uevent
usb 2-6.3.3: uevent
usb 2-6.1: uevent
usb 2-6.3.3:1.1: uevent
usb 2-6.3.3: uevent
usb 2-3.1.1:1.0: uevent
usb 2-3.1.1: uevent
usb 2-6.3.3:1.1: uevent
usb 2-6.3.3: uevent
usb 2-6.1:1.0: uevent
usb 2-3.1.1:1.1: uevent
usb 2-6.3.3:1.0: uevent
usb 2-6.1:1.0: uevent
usb 2-6.3.3:1.1: uevent
usb 2-3.1.1:1.1: uevent
usb 2-3.1.1:1.0: uevent
usb 2-6.3.3:1.1: uevent
PM: Adding info for No Bus:dv1394-0
usb 2-3.1.2.1:1.0: uevent
usb 2-3.1.2.1: uevent
usb 2-3.1.2.1:1.0: uevent
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
hda: command error: status=0x51 { DriveReady SeekComplete Error }
hda: command error: error=0x50 { LastFailedSense=0x05 }
hda: possibly failed opcode: 0xa0
end_request: I/O error, dev hda, sector 0
Buffer I/O error on device hda, logical block 0
Buffer I/O error on device hda, logical block 1
Buffer I/O error on device hda, logical block 2
Buffer I/O error on device hda, logical block 3
Buffer I/O error on device hda, logical block 4
Buffer I/O error on device hda, logical block 5
Buffer I/O error on device hda, logical block 6
Buffer I/O error on device hda, logical block 7
usb 2-3.1.2.1:1.0: uevent
usb 2-3.1.2.1: uevent
hda: command error: status=0x51 { DriveReady SeekComplete Error }
hda: command error: error=0x50 { LastFailedSense=0x05 }
hda: possibly failed opcode: 0xa0
usb 2-3.1.2.1:1.0: uevent
end_request: I/O error, dev hda, sector 0
Buffer I/O error on device hda, logical block 0
Buffer I/O error on device hda, logical block 1
hda: command error: status=0x51 { DriveReady SeekComplete Error }
hda: command error: error=0x50 { LastFailedSense=0x05 }
hda: possibly failed opcode: 0xa0
end_request: I/O error, dev hda, sector 0
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001403 POWER sig=k CSC CONNECT
hub 2-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
ehci_hcd 0000:00:0b.1: port 1 low speed --> companion
ehci_hcd 0000:00:0b.1: GetStatus port 1 status 003402 POWER OWNER sig=k CSC
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030301 PESC CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
PM: Adding info for No Bus:sg0
sd 1:0:0:0: Attached scsi generic sg0 type 0
PM: Adding info for No Bus:sg1
sd 2:0:0:0: Attached scsi generic sg1 type 0
PM: Adding info for No Bus:sg2
sr 4:0:0:0: Attached scsi generic sg2 type 5
PM: Adding info for No Bus:sg3
sd 0:0:0:0: Attached scsi generic sg3 type 0
PM: Adding info for No Bus:sg4
sd 0:0:0:1: Attached scsi generic sg4 type 0
PM: Adding info for No Bus:sg5
sd 0:0:0:2: Attached scsi generic sg5 type 0
PM: Adding info for No Bus:sg6
sd 0:0:0:3: Attached scsi generic sg6 type 0
PM: Adding info for No Bus:sg7
sd 5:0:0:0: Attached scsi generic sg7 type 0
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
PM: Adding info for No Bus:timer
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00130300 PRSC PESC CSC LSDA PPS
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0002
PM: Adding info for No Bus:seq
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
ohci_hcd 0000:00:0b.0: GetStatus roothub.portstatus [0] = 0x00030300 PESC CSC LSDA PPS
hub 1-0:1.0: port 1, status 0300, change 0003, 1.5 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x300
hda: UDMA/66 mode selected
PM: Adding info for No Bus:sequencer
PM: Adding info for No Bus:sequencer2
ACPI: PCI Interrupt Link [AAZA] enabled at IRQ 23
HDA Intel 0000:00:10.1: PCI INT B -> Link[AAZA] -> GSI 23 (level, low) -> IRQ 23
HDA Intel 0000:00:10.1: setting latency timer to 64
PM: Adding info for No Bus:input8
input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:10.1/input/input8
PM: Adding info for No Bus:event8
PM: Adding info for No Bus:card0
PM: Adding info for No Bus:pcmC0D1p
PM: Adding info for No Bus:adsp
PM: Adding info for No Bus:pcmC0D0p
PM: Adding info for No Bus:pcmC0D0c
PM: Adding info for No Bus:dsp
PM: Adding info for No Bus:audio
PM: Adding info for No Bus:hwC0D0
PM: Adding info for No Bus:controlC0
PM: Adding info for No Bus:mixer
ohci_hcd 0000:00:0b.0: auto-stop root hub
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
sr 4:0:0:0: [sr0] CDB: Read(10): 28 00 00 00 00 00 00 00 40 00
ata4.00: cmd a0/01:00:00:00:fc/00:00:00:00:00/a0 tag 0 dma 131072 in
res 40/00:02:00:20:00/00:00:00:00:00/a0 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for UDMA/100
ata4: EH complete
ata4: limiting SATA link speed to 1.5 Gbps
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
sr 4:0:0:0: [sr0] CDB: Read(10): 28 00 00 00 00 00 00 00 40 00
ata4.00: cmd a0/01:00:00:00:fc/00:00:00:00:00/a0 tag 0 dma 131072 in
res 40/00:02:00:20:00/00:00:00:00:00/a0 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for UDMA/100
ata4: EH complete
ata4.00: limiting speed to UDMA/66:PIO4
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
sr 4:0:0:0: [sr0] CDB: Read(10): 28 00 00 00 00 00 00 00 40 00
ata4.00: cmd a0/01:00:00:00:fc/00:00:00:00:00/a0 tag 0 dma 131072 in
res 40/00:02:00:20:00/00:00:00:00:00/a0 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for UDMA/66
ata4: EH complete
ata4.00: limiting speed to UDMA/33:PIO4
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
sr 4:0:0:0: [sr0] CDB: Read(10): 28 00 00 00 00 00 00 00 40 00
ata4.00: cmd a0/01:00:00:00:fc/00:00:00:00:00/a0 tag 0 dma 131072 in
res 40/00:02:00:20:00/00:00:00:00:00/a0 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for UDMA/33
sr 4:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
sr 4:0:0:0: [sr0] Sense Key : Aborted Command [current] [descriptor]
Descriptor sense data with sense descriptors (in hex):
72 0b 00 00 00 00 00 0e 09 0c 00 00 00 02 00 00
00 20 00 00 a0 40
sr 4:0:0:0: [sr0] Add. Sense: No additional sense information
sr 4:0:0:0: [sr0] CDB: Read(10): 28 00 00 00 00 00 00 00 40 00
end_request: I/O error, dev sr0, sector 0
__ratelimit: 2 callbacks suppressed
Buffer I/O error on device sr0, logical block 0
Buffer I/O error on device sr0, logical block 1
Buffer I/O error on device sr0, logical block 2
Buffer I/O error on device sr0, logical block 3
Buffer I/O error on device sr0, logical block 4
Buffer I/O error on device sr0, logical block 5
Buffer I/O error on device sr0, logical block 6
Buffer I/O error on device sr0, logical block 7
Buffer I/O error on device sr0, logical block 8
Buffer I/O error on device sr0, logical block 9
ata4: EH complete
ata4.00: limiting speed to PIO4
ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
sr 4:0:0:0: [sr0] CDB: Read(10): 28 00 00 00 00 00 00 00 08 00
ata4.00: cmd a0/01:00:00:00:40/00:00:00:00:00/a0 tag 0 dma 16384 in
res 40/00:02:00:20:00/00:00:00:00:00/a0 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: nv: skipping hardreset on occupied port
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for PIO4
ata4: EH complete
PM: Adding info for No Bus:vcs2
PM: Adding info for No Bus:vcsa2
PM: Adding info for No Bus:vcs3
PM: Adding info for No Bus:vcsa3
PM: Adding info for No Bus:vcs4
PM: Adding info for No Bus:vcsa4
PM: Adding info for No Bus:vcs5
PM: Adding info for No Bus:vcsa5
PM: Adding info for No Bus:vcs6
PM: Adding info for No Bus:vcsa6
hda: UDMA/66 mode selected
EXT3 FS on dm-1, internal journal
i2c /dev entries driver
PM: Adding info for No Bus:i2c-0
it87: Found IT8712F chip at 0x290, revision 7
it87: in3 is VCC (+5V)
it87: in7 is VCCH (+5V Stand-By)
ACPI: I/O resource it87 [0x295-0x296] conflicts with ACPI region HWRE [0x295-0x296]
ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
fuse init (API version 7.13)
PM: Adding info for No Bus:fuse
kjournald starting. Commit interval 5 seconds
EXT3 FS on dm-5, internal journal
EXT3-fs: mounted filesystem with writeback data mode.
PM: Adding info for No Bus:254:2-fuseblk
PM: Adding info for No Bus:254:6-fuseblk
Adding 4194296k swap on /mnt/oldlin/4G-memory.swap. Priority:-1 extents:1057 across:4264956k
r8169: eth1: link up
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PM: Adding info for No Bus:0:16
PM: Adding info for No Bus:0:17
PM: Adding info for No Bus:0:18
r8169: eth1: link up
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: sata_nv times out for BD-ROM iHOS104-08
2010-03-09 5:18 ` Cengiz Günay
@ 2010-05-25 19:34 ` Tejun Heo
0 siblings, 0 replies; 28+ messages in thread
From: Tejun Heo @ 2010-05-25 19:34 UTC (permalink / raw)
To: Cengiz Günay; +Cc: Robert Hancock, linux-kernel, linux-ide
[-- Attachment #1: Type: text/plain, Size: 672 bytes --]
Hello,
Alright, I don't have access to mcp51 but tested with mcp55 and could
reproduce similar problem. It seems nIEN on mcp55 is stuck once set
and iHOS104 doesn't set I on D2H FIS if nIEN is set on command H2D
FIS, which the SATA standard specifically mandates not to do. So, the
combination of buggy mcp55 ctl handling + buggy iHOS104 nIEN handling
leads to nobody raising interrupt.
The problem is that the problem I'm seeing is not completely identical
to the one you're seeing. The difference could be coming from
different firmware version on the drives or different controllers.
Anyways, can you please give a shot at the attached patch?
Thanks.
--
tejun
[-- Attachment #2: dont-diddle-with-nIEN.patch --]
[-- Type: text/x-patch, Size: 717 bytes --]
diff --git a/drivers/ata/sata_nv.c b/drivers/ata/sata_nv.c
index baa8f0d..69d23c2 100644
--- a/drivers/ata/sata_nv.c
+++ b/drivers/ata/sata_nv.c
@@ -1669,7 +1669,6 @@ static void nv_mcp55_freeze(struct ata_port *ap)
mask = readl(mmio_base + NV_INT_ENABLE_MCP55);
mask &= ~(NV_INT_ALL_MCP55 << shift);
writel(mask, mmio_base + NV_INT_ENABLE_MCP55);
- ata_sff_freeze(ap);
}
static void nv_mcp55_thaw(struct ata_port *ap)
@@ -1683,7 +1682,6 @@ static void nv_mcp55_thaw(struct ata_port *ap)
mask = readl(mmio_base + NV_INT_ENABLE_MCP55);
mask |= (NV_INT_MASK_MCP55 << shift);
writel(mask, mmio_base + NV_INT_ENABLE_MCP55);
- ata_sff_thaw(ap);
}
static void nv_adma_error_handler(struct ata_port *ap)
^ permalink raw reply related [flat|nested] 28+ messages in thread
* Re: sata_nv times out for BD-ROM iHOS104-08
@ 2010-06-03 17:40 Gregory Moyer
0 siblings, 0 replies; 28+ messages in thread
From: Gregory Moyer @ 2010-06-03 17:40 UTC (permalink / raw)
To: linux-kernel
> Hello,
>
> Alright, I don't have access to mcp51 but tested with mcp55 and could
> reproduce similar problem. It seems nIEN on mcp55 is stuck once set
> and iHOS104 doesn't set I on D2H FIS if nIEN is set on command H2D
> FIS, which the SATA standard specifically mandates not to do. So, the
> combination of buggy mcp55 ctl handling + buggy iHOS104 nIEN handling
> leads to nobody raising interrupt.
>
> The problem is that the problem I'm seeing is not completely identical
> to the one you're seeing. The difference could be coming from
> different firmware version on the drives or different controllers.
>
> Anyways, can you please give a shot at the attached patch?
>
> Thanks.
>
> --
> tejun
I tried your latest patch against 2.6.32 with my iHOS104 and MCP55 and
it works perfectly. I can now use the drive normally and I do not see
any failure/reset messages in the log. Thanks!
- Greg
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: sata_nv times out for BD-ROM iHOS104-08
@ 2010-01-21 3:15 Gregory Moyer
0 siblings, 0 replies; 28+ messages in thread
From: Gregory Moyer @ 2010-01-21 3:15 UTC (permalink / raw)
To: linux-kernel
[-- Attachment #1: Type: text/plain, Size: 795 bytes --]
> > Hmm.... it worked? Does kernel parameter sata_nv.adma_enabled=0 make
> > any difference? Can you please attach boot log with the kernel
> > parameter specified?
>
> Think you meant maybe sata_nv.swncq=0 instead - this is an MCP51
> controller so it doesn't support ADMA. I don't imagine SWNCQ would
> make any difference with an ATAPI device, but wouldn't hurt to try.
I tried booting 2.6.32 with both of these options (tried separately)
with no change in behavior. If it helps, sometimes I get an error mask
of 0x4 and sometimes 0x5, though I do not know what either represents.
Also, my controller is MCP55, but I don't know how different that is
from the MCP51 that Cengiz has.
Attached are boot logs from running each option suggested here.
Thanks again.
- Greg
[-- Attachment #2: boot.2.6.32.adma.disabled.log --]
[-- Type: text/x-log, Size: 47322 bytes --]
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.32-020632-generic (root@zinc) (gcc version 4.2.3 (Ubuntu 4.2.3-2ubuntu7)) #020632 SMP Thu Dec 3 10:09:58 UTC 2009
[ 0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-2.6.32-020632-generic root=UUID=2e50af70-690f-48f4-a8e8-32472593f9d7 ro sata_nv.adma_enabled=0
[ 0.000000] KERNEL supported cpus:
[ 0.000000] Intel GenuineIntel
[ 0.000000] AMD AuthenticAMD
[ 0.000000] Centaur CentaurHauls
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009b800 (usable)
[ 0.000000] BIOS-e820: 000000000009b800 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000007fef0000 (usable)
[ 0.000000] BIOS-e820: 000000007fef0000 - 000000007fef3000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000007fef3000 - 000000007ff00000 (ACPI data)
[ 0.000000] BIOS-e820: 00000000d0000000 - 00000000f0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
[ 0.000000] DMI 2.4 present.
[ 0.000000] Phoenix BIOS detected: BIOS may corrupt low RAM, working around it.
[ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[ 0.000000] last_pfn = 0x7fef0 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-CBFFF write-protect
[ 0.000000] CC000-FFFFF uncachable
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000 mask F80000000 write-back
[ 0.000000] 1 base 07FF00000 mask FFFF00000 uncachable
[ 0.000000] 2 disabled
[ 0.000000] 3 disabled
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] Scanning 0 areas for low memory corruption
[ 0.000000] modified physical RAM map:
[ 0.000000] modified: 0000000000000000 - 0000000000010000 (reserved)
[ 0.000000] modified: 0000000000010000 - 000000000009b800 (usable)
[ 0.000000] modified: 000000000009b800 - 00000000000a0000 (reserved)
[ 0.000000] modified: 00000000000f0000 - 0000000000100000 (reserved)
[ 0.000000] modified: 0000000000100000 - 000000007fef0000 (usable)
[ 0.000000] modified: 000000007fef0000 - 000000007fef3000 (ACPI NVS)
[ 0.000000] modified: 000000007fef3000 - 000000007ff00000 (ACPI data)
[ 0.000000] modified: 00000000d0000000 - 00000000f0000000 (reserved)
[ 0.000000] modified: 00000000fec00000 - 0000000100000000 (reserved)
[ 0.000000] initial memory mapped : 0 - 20000000
[ 0.000000] init_memory_mapping: 0000000000000000-000000007fef0000
[ 0.000000] 0000000000 - 007fe00000 page 2M
[ 0.000000] 007fe00000 - 007fef0000 page 4k
[ 0.000000] kernel direct mapping tables up to 7fef0000 @ 10000-14000
[ 0.000000] RAMDISK: 377cc000 - 37fef7b0
[ 0.000000] ACPI: RSDP 00000000000f7fa0 00014 (v00 Nvidia)
[ 0.000000] ACPI: RSDT 000000007fef3040 00038 (v01 Nvidia NVDAACPI 42302E31 NVDA 00000000)
[ 0.000000] ACPI: FACP 000000007fef30c0 00074 (v01 Nvidia NVDAACPI 42302E31 NVDA 00000000)
[ 0.000000] ACPI: DSDT 000000007fef3180 0541D (v01 NVIDIA NVDAACPI 00001000 MSFT 03000000)
[ 0.000000] ACPI: FACS 000000007fef0000 00040
[ 0.000000] ACPI: HPET 000000007fef8700 00038 (v01 Nvidia NVDAACPI 42302E31 NVDA 00000098)
[ 0.000000] ACPI: WDRT 000000007fef8780 00047 (v01 Nvidia NVDAACPI 42302E31 NVDA 00000000)
[ 0.000000] ACPI: MCFG 000000007fef8840 0003C (v01 Nvidia NVDAACPI 42302E31 NVDA 00000000)
[ 0.000000] ACPI: APIC 000000007fef8600 00098 (v01 Nvidia NVDAACPI 42302E31 NVDA 00000000)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at 0000000000000000-000000007fef0000
[ 0.000000] Bootmem setup node 0 0000000000000000-000000007fef0000
[ 0.000000] NODE_DATA [0000000000012000 - 0000000000016fff]
[ 0.000000] bootmap [0000000000017000 - 0000000000026fdf] pages 10
[ 0.000000] (7 early reservations) ==> bootmem [0000000000 - 007fef0000]
[ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
[ 0.000000] #1 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000]
[ 0.000000] #2 [0001000000 - 0001a2f784] TEXT DATA BSS ==> [0001000000 - 0001a2f784]
[ 0.000000] #3 [00377cc000 - 0037fef7b0] RAMDISK ==> [00377cc000 - 0037fef7b0]
[ 0.000000] #4 [000009b800 - 0000100000] BIOS reserved ==> [000009b800 - 0000100000]
[ 0.000000] #5 [0001a30000 - 0001a300b2] BRK ==> [0001a30000 - 0001a300b2]
[ 0.000000] #6 [0000010000 - 0000012000] PGTABLE ==> [0000010000 - 0000012000]
[ 0.000000] found SMP MP-table at [ffff8800000f3fd0] f3fd0
[ 0.000000] [ffffea0000000000-ffffea0001bfffff] PMD -> [ffff880002000000-ffff880003bfffff] on node 0
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000010 -> 0x00001000
[ 0.000000] DMA32 0x00001000 -> 0x00100000
[ 0.000000] Normal 0x00100000 -> 0x00100000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[2] active PFN ranges
[ 0.000000] 0: 0x00000010 -> 0x0000009b
[ 0.000000] 0: 0x00000100 -> 0x0007fef0
[ 0.000000] On node 0 totalpages: 523899
[ 0.000000] DMA zone: 56 pages used for memmap
[ 0.000000] DMA zone: 105 pages reserved
[ 0.000000] DMA zone: 3818 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 7109 pages used for memmap
[ 0.000000] DMA32 zone: 512811 pages, LIFO batch:31
[ 0.000000] ACPI: PM-Timer IO Port: 0x1008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x03] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 4, version 17, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] ACPI: IRQ14 used by override.
[ 0.000000] ACPI: IRQ15 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x10de8201 base: 0xfeff0000
[ 0.000000] SMP: Allowing 4 CPUs, 0 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 24
[ 0.000000] PM: Registered nosave memory: 000000000009b000 - 000000000009c000
[ 0.000000] PM: Registered nosave memory: 000000000009c000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
[ 0.000000] PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
[ 0.000000] Allocating PCI resources starting at 7ff00000 (gap: 7ff00000:50100000)
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] NR_CPUS:64 nr_cpumask_bits:64 nr_cpu_ids:4 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 30 pages/cpu @ffff880001c00000 s91288 r8192 d23400 u524288
[ 0.000000] pcpu-alloc: s91288 r8192 d23400 u524288 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1 2 3
[ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 516629
[ 0.000000] Policy zone: DMA32
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.32-020632-generic root=UUID=2e50af70-690f-48f4-a8e8-32472593f9d7 ro sata_nv.adma_enabled=0
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Initializing CPU#0
[ 0.000000] Checking aperture...
[ 0.000000] No AGP bridge found
[ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
[ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[ 0.000000] Memory: 2047508k/2096064k available (5355k kernel code, 468k absent, 48088k reserved, 3200k data, 728k init)
[ 0.000000] SLUB: Genslabs=14, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:4352 nr_irqs:440
[ 0.000000] spurious 8259A interrupt: IRQ7.
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] allocated 20971520 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] hpet clockevent registered
[ 0.000000] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 2666.454 MHz processor.
[ 0.010008] Calibrating delay loop (skipped), value calculated using timer frequency.. 5332.90 BogoMIPS (lpj=26664540)
[ 0.010232] Security Framework initialized
[ 0.010333] SELinux: Disabled at boot.
[ 0.010580] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.012294] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.013061] Mount-cache hash table entries: 256
[ 0.013323] Initializing cgroup subsys ns
[ 0.013419] Initializing cgroup subsys cpuacct
[ 0.013515] Initializing cgroup subsys memory
[ 0.013615] Initializing cgroup subsys freezer
[ 0.013710] Initializing cgroup subsys net_cls
[ 0.013824] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.013964] CPU: L2 cache: 4096K
[ 0.014055] CPU 0/0x0 -> Node 0
[ 0.014144] CPU: Physical Processor ID: 0
[ 0.014237] CPU: Processor Core ID: 0
[ 0.014330] mce: CPU supports 6 MCE banks
[ 0.014428] CPU0: Thermal monitoring enabled (TM1)
[ 0.014528] using mwait in idle threads.
[ 0.014621] Performance Events: Core2 events, Intel PMU driver.
[ 0.014813] ... version: 2
[ 0.014906] ... bit width: 40
[ 0.014998] ... generic registers: 2
[ 0.015091] ... value mask: 000000ffffffffff
[ 0.015189] ... max period: 000000007fffffff
[ 0.015287] ... fixed-purpose events: 3
[ 0.015380] ... event mask: 0000000700000003
[ 0.017693] ACPI: Core revision 20090903
[ 0.026875] Setting APIC routing to flat
[ 0.027373] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.127489] CPU0: Intel(R) Core(TM)2 Quad CPU @ 2.66GHz stepping 07
[ 0.130000] Booting processor 1 APIC 0x3 ip 0x6000
[ 0.020000] Initializing CPU#1
[ 0.020000] Calibrating delay using timer specific routine.. 5333.35 BogoMIPS (lpj=26666750)
[ 0.020000] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.020000] CPU: L2 cache: 4096K
[ 0.020000] CPU 1/0x3 -> Node 0
[ 0.020000] CPU: Physical Processor ID: 0
[ 0.020000] CPU: Processor Core ID: 3
[ 0.020000] CPU1: Thermal monitoring enabled (TM1)
[ 0.280103] CPU1: Intel(R) Core(TM)2 Quad CPU @ 2.66GHz stepping 07
[ 0.281075] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[ 0.290098] Booting processor 2 APIC 0x1 ip 0x6000
[ 0.020000] Initializing CPU#2
[ 0.020000] Calibrating delay using timer specific routine.. 5333.35 BogoMIPS (lpj=26666750)
[ 0.020000] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.020000] CPU: L2 cache: 4096K
[ 0.020000] CPU 2/0x1 -> Node 0
[ 0.020000] CPU: Physical Processor ID: 0
[ 0.020000] CPU: Processor Core ID: 1
[ 0.020000] CPU2: Thermal monitoring enabled (TM1)
[ 0.450118] CPU2: Intel(R) Core(TM)2 Quad CPU @ 2.66GHz stepping 07
[ 0.451090] checking TSC synchronization [CPU#0 -> CPU#2]: passed.
[ 0.460111] Booting processor 3 APIC 0x2 ip 0x6000
[ 0.020000] Initializing CPU#3
[ 0.020000] Calibrating delay using timer specific routine.. 5333.30 BogoMIPS (lpj=26666544)
[ 0.020000] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.020000] CPU: L2 cache: 4096K
[ 0.020000] CPU 3/0x2 -> Node 0
[ 0.020000] CPU: Physical Processor ID: 0
[ 0.020000] CPU: Processor Core ID: 2
[ 0.020000] CPU3: Thermal monitoring enabled (TM1)
[ 0.620048] CPU3: Intel(R) Core(TM)2 Quad CPU @ 2.66GHz stepping 07
[ 0.622431] checking TSC synchronization [CPU#0 -> CPU#3]: passed.
[ 0.630011] Brought up 4 CPUs
[ 0.630103] Total of 4 processors activated (21332.91 BogoMIPS).
[ 0.631657] CPU0 attaching sched-domain:
[ 0.631661] domain 0: span 0,2 level MC
[ 0.631663] groups: 0 2
[ 0.631667] domain 1: span 0-3 level CPU
[ 0.631668] groups: 0,2 (cpu_power = 2048) 1,3 (cpu_power = 2048)
[ 0.631675] CPU1 attaching sched-domain:
[ 0.631677] domain 0: span 1,3 level MC
[ 0.631678] groups: 1 3
[ 0.631681] domain 1: span 0-3 level CPU
[ 0.631683] groups: 1,3 (cpu_power = 2048) 0,2 (cpu_power = 2048)
[ 0.631688] CPU2 attaching sched-domain:
[ 0.631689] domain 0: span 0,2 level MC
[ 0.631691] groups: 2 0
[ 0.631694] domain 1: span 0-3 level CPU
[ 0.631696] groups: 0,2 (cpu_power = 2048) 1,3 (cpu_power = 2048)
[ 0.631701] CPU3 attaching sched-domain:
[ 0.631702] domain 0: span 1,3 level MC
[ 0.631704] groups: 3 1
[ 0.631707] domain 1: span 0-3 level CPU
[ 0.631708] groups: 1,3 (cpu_power = 2048) 0,2 (cpu_power = 2048)
[ 0.631851] regulator: core version 0.5
[ 0.631851] Time: 3:02:06 Date: 01/21/10
[ 0.631851] NET: Registered protocol family 16
[ 0.631851] ACPI: bus type pci registered
[ 0.631851] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
[ 0.631851] PCI: MCFG area at e0000000 reserved in E820
[ 0.632976] PCI: Using MMCONFIG at e0000000 - efffffff
[ 0.633074] PCI: Using configuration type 1 for base access
[ 0.633808] bio: create slab <bio-0> at 0
[ 0.640076] ACPI: EC: Look up EC in DSDT
[ 0.646140] ACPI: Interpreter enabled
[ 0.646252] ACPI: (supports S0 S1 S3 S4 S5)
[ 0.646584] ACPI: Using IOAPIC for interrupt routing
[ 0.646888] ACPI: BIOS _OSI(Linux) query ignored
[ 0.654045] ACPI: No dock devices found.
[ 0.654264] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.655172] pci 0000:00:03.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.655277] pci 0000:00:03.0: PME# disabled
[ 0.655554] pci 0000:00:0a.0: reg 10 io port: [0xfc00-0xfc7f]
[ 0.655603] pci 0000:00:0a.1: reg 10 io port: [0xf800-0xf83f]
[ 0.655618] pci 0000:00:0a.1: reg 20 io port: [0xf400-0xf43f]
[ 0.655623] pci 0000:00:0a.1: reg 24 io port: [0xf000-0xf03f]
[ 0.655646] pci 0000:00:0a.1: PME# supported from D3hot D3cold
[ 0.655751] pci 0000:00:0a.1: PME# disabled
[ 0.655876] pci 0000:00:0b.0: reg 10 32bit mmio: [0xcffff000-0xcfffffff]
[ 0.655905] pci 0000:00:0b.0: supports D1 D2
[ 0.655907] pci 0000:00:0b.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.656012] pci 0000:00:0b.0: PME# disabled
[ 0.656130] pci 0000:00:0b.1: reg 10 32bit mmio: [0xcfffe000-0xcfffe0ff]
[ 0.656162] pci 0000:00:0b.1: supports D1 D2
[ 0.656163] pci 0000:00:0b.1: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.656269] pci 0000:00:0b.1: PME# disabled
[ 0.656401] pci 0000:00:0d.0: reg 20 io port: [0xec00-0xec0f]
[ 0.656443] pci 0000:00:0e.0: reg 10 io port: [0x9f0-0x9f7]
[ 0.656447] pci 0000:00:0e.0: reg 14 io port: [0xbf0-0xbf3]
[ 0.656452] pci 0000:00:0e.0: reg 18 io port: [0x970-0x977]
[ 0.656456] pci 0000:00:0e.0: reg 1c io port: [0xb70-0xb73]
[ 0.656460] pci 0000:00:0e.0: reg 20 io port: [0xd800-0xd80f]
[ 0.656465] pci 0000:00:0e.0: reg 24 32bit mmio: [0xcfffd000-0xcfffdfff]
[ 0.656512] pci 0000:00:0e.1: reg 10 io port: [0x9e0-0x9e7]
[ 0.656516] pci 0000:00:0e.1: reg 14 io port: [0xbe0-0xbe3]
[ 0.656521] pci 0000:00:0e.1: reg 18 io port: [0x960-0x967]
[ 0.656525] pci 0000:00:0e.1: reg 1c io port: [0xb60-0xb63]
[ 0.656529] pci 0000:00:0e.1: reg 20 io port: [0xc400-0xc40f]
[ 0.656533] pci 0000:00:0e.1: reg 24 32bit mmio: [0xcfffc000-0xcfffcfff]
[ 0.656581] pci 0000:00:0e.2: reg 10 io port: [0xc000-0xc007]
[ 0.656585] pci 0000:00:0e.2: reg 14 io port: [0xbc00-0xbc03]
[ 0.656589] pci 0000:00:0e.2: reg 18 io port: [0xb800-0xb807]
[ 0.656594] pci 0000:00:0e.2: reg 1c io port: [0xb400-0xb403]
[ 0.656598] pci 0000:00:0e.2: reg 20 io port: [0xb000-0xb00f]
[ 0.656602] pci 0000:00:0e.2: reg 24 32bit mmio: [0xcfffb000-0xcfffbfff]
[ 0.656699] pci 0000:00:0f.1: reg 10 32bit mmio: [0xcfff0000-0xcfff3fff]
[ 0.656734] pci 0000:00:0f.1: PME# supported from D3hot D3cold
[ 0.656837] pci 0000:00:0f.1: PME# disabled
[ 0.656977] pci 0000:00:11.0: reg 10 32bit mmio: [0xcfffa000-0xcfffafff]
[ 0.656981] pci 0000:00:11.0: reg 14 io port: [0xac00-0xac07]
[ 0.656986] pci 0000:00:11.0: reg 18 32bit mmio: [0xcfff9000-0xcfff90ff]
[ 0.656990] pci 0000:00:11.0: reg 1c 32bit mmio: [0xcfff8000-0xcfff800f]
[ 0.657020] pci 0000:00:11.0: supports D1 D2
[ 0.657022] pci 0000:00:11.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.657128] pci 0000:00:11.0: PME# disabled
[ 0.657261] pci 0000:00:12.0: reg 10 32bit mmio: [0xcfff7000-0xcfff7fff]
[ 0.657265] pci 0000:00:12.0: reg 14 io port: [0xa800-0xa807]
[ 0.657270] pci 0000:00:12.0: reg 18 32bit mmio: [0xcfff6000-0xcfff60ff]
[ 0.657274] pci 0000:00:12.0: reg 1c 32bit mmio: [0xcfff5000-0xcfff500f]
[ 0.657304] pci 0000:00:12.0: supports D1 D2
[ 0.657306] pci 0000:00:12.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.657412] pci 0000:00:12.0: PME# disabled
[ 0.657570] pci 0000:00:18.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.657675] pci 0000:00:18.0: PME# disabled
[ 0.657808] pci 0000:01:00.0: reg 10 32bit mmio: [0xcc000000-0xccffffff]
[ 0.657816] pci 0000:01:00.0: reg 14 64bit mmio pref: [0xb0000000-0xbfffffff]
[ 0.657823] pci 0000:01:00.0: reg 1c 64bit mmio: [0xca000000-0xcbffffff]
[ 0.657827] pci 0000:01:00.0: reg 24 io port: [0x9c00-0x9c7f]
[ 0.657832] pci 0000:01:00.0: reg 30 32bit mmio pref: [0x000000-0x01ffff]
[ 0.657892] pci 0000:00:03.0: bridge io port: [0x9000-0x9fff]
[ 0.657894] pci 0000:00:03.0: bridge 32bit mmio: [0xca000000-0xcdffffff]
[ 0.657898] pci 0000:00:03.0: bridge 64bit mmio pref: [0xb0000000-0xbfffffff]
[ 0.657933] pci 0000:02:07.0: reg 10 32bit mmio: [0xcfeff000-0xcfeff7ff]
[ 0.657939] pci 0000:02:07.0: reg 14 32bit mmio: [0xcfef8000-0xcfefbfff]
[ 0.657973] pci 0000:02:07.0: supports D1 D2
[ 0.657975] pci 0000:02:07.0: PME# supported from D0 D1 D2 D3hot
[ 0.658078] pci 0000:02:07.0: PME# disabled
[ 0.658198] pci 0000:02:09.0: reg 10 io port: [0x8c00-0x8c1f]
[ 0.658234] pci 0000:02:09.0: supports D1 D2
[ 0.658263] pci 0000:00:0f.0: transparent bridge
[ 0.658359] pci 0000:00:0f.0: bridge io port: [0x8000-0x8fff]
[ 0.658362] pci 0000:00:0f.0: bridge 32bit mmio: [0xcfe00000-0xcfefffff]
[ 0.658391] pci 0000:03:00.0: reg 10 32bit mmio: [0xc8000000-0xc8ffffff]
[ 0.658400] pci 0000:03:00.0: reg 14 64bit mmio pref: [0xa0000000-0xafffffff]
[ 0.658408] pci 0000:03:00.0: reg 1c 64bit mmio: [0xc6000000-0xc7ffffff]
[ 0.658413] pci 0000:03:00.0: reg 24 io port: [0x7c00-0x7c7f]
[ 0.658418] pci 0000:03:00.0: reg 30 32bit mmio pref: [0x000000-0x01ffff]
[ 0.658483] pci 0000:00:18.0: bridge io port: [0x7000-0x7fff]
[ 0.658486] pci 0000:00:18.0: bridge 32bit mmio: [0xc6000000-0xc9ffffff]
[ 0.658490] pci 0000:00:18.0: bridge 64bit mmio pref: [0xa0000000-0xafffffff]
[ 0.658502] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.658816] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
[ 0.723799] ACPI: PCI Interrupt Link [LNK1] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[ 0.724539] ACPI: PCI Interrupt Link [LNK2] (IRQs 5 7 9 10 *11 14 15)
[ 0.725153] ACPI: PCI Interrupt Link [LNK3] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[ 0.725891] ACPI: PCI Interrupt Link [LNK4] (IRQs 5 7 9 10 *11 14 15)
[ 0.726505] ACPI: PCI Interrupt Link [LXV5] (IRQs 5 7 9 *10 11 14 15)
[ 0.727118] ACPI: PCI Interrupt Link [LXV6] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[ 0.727854] ACPI: PCI Interrupt Link [LXV7] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[ 0.728590] ACPI: PCI Interrupt Link [LXV8] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[ 0.729328] ACPI: PCI Interrupt Link [LUBA] (IRQs 5 7 9 10 *11 14 15)
[ 0.729942] ACPI: PCI Interrupt Link [LMC1] (IRQs *5 7 9 10 11 14 15)
[ 0.730552] ACPI: PCI Interrupt Link [LMAC] (IRQs *5 7 9 10 11 14 15)
[ 0.731172] ACPI: PCI Interrupt Link [LAZA] (IRQs 5 7 9 *10 11 14 15)
[ 0.731784] ACPI: PCI Interrupt Link [LSMB] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[ 0.732544] ACPI: PCI Interrupt Link [LUB2] (IRQs 5 7 9 *10 11 14 15)
[ 0.733156] ACPI: PCI Interrupt Link [LIDE] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[ 0.733903] ACPI: PCI Interrupt Link [LSA0] (IRQs 5 7 9 10 *11 14 15)
[ 0.734516] ACPI: PCI Interrupt Link [LSA1] (IRQs 5 7 9 *10 11 14 15)
[ 0.735134] ACPI: PCI Interrupt Link [LSA2] (IRQs 5 7 9 10 *11 14 15)
[ 0.735787] ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0, disabled.
[ 0.736254] ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0
[ 0.736673] ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0, disabled.
[ 0.737139] ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0
[ 0.737556] ACPI: PCI Interrupt Link [AXV5] (IRQs 16) *0
[ 0.737973] ACPI: PCI Interrupt Link [AXV6] (IRQs 16) *0, disabled.
[ 0.738439] ACPI: PCI Interrupt Link [AXV7] (IRQs 16) *0, disabled.
[ 0.738904] ACPI: PCI Interrupt Link [AXV8] (IRQs 16) *0, disabled.
[ 0.739370] ACPI: PCI Interrupt Link [AUBA] (IRQs 22 23) *0
[ 0.739833] ACPI: PCI Interrupt Link [AMA1] (IRQs 22 23) *0
[ 0.740266] ACPI: PCI Interrupt Link [AMAC] (IRQs 22 23) *0
[ 0.740730] ACPI: PCI Interrupt Link [AAZA] (IRQs 22 23) *0
[ 0.741192] ACPI: PCI Interrupt Link [AACI] (IRQs 22 23) *0, disabled.
[ 0.741703] ACPI: PCI Interrupt Link [AMCI] (IRQs 22 23) *0, disabled.
[ 0.742233] ACPI: PCI Interrupt Link [ASMB] (IRQs 22 23) *0, disabled.
[ 0.742744] ACPI: PCI Interrupt Link [AUS2] (IRQs 22 23) *0
[ 0.743227] ACPI: PCI Interrupt Link [AIDE] (IRQs 22 23) *0, disabled.
[ 0.743738] ACPI: PCI Interrupt Link [ASA0] (IRQs 20 21) *0
[ 0.744203] ACPI: PCI Interrupt Link [ASA1] (IRQs 20 21) *0
[ 0.744669] ACPI: PCI Interrupt Link [ASA2] (IRQs 20 21) *0
[ 0.745079] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.745224] vgaarb: device added: PCI:0000:03:00.0,decodes=io+mem,owns=none,locks=none
[ 0.745365] vgaarb: loaded
[ 0.745536] SCSI subsystem initialized
[ 0.745661] libata version 3.00 loaded.
[ 0.745661] usbcore: registered new interface driver usbfs
[ 0.745661] usbcore: registered new interface driver hub
[ 0.745661] usbcore: registered new device driver usb
[ 0.745661] ACPI: WMI: Mapper loaded
[ 0.745661] PCI: Using ACPI for IRQ routing
[ 0.745661] Bluetooth: Core ver 2.15
[ 0.745661] NET: Registered protocol family 31
[ 0.745661] Bluetooth: HCI device and connection manager initialized
[ 0.745661] Bluetooth: HCI socket layer initialized
[ 0.745661] NetLabel: Initializing
[ 0.745661] NetLabel: domain hash size = 128
[ 0.745661] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.745661] NetLabel: unlabeled traffic allowed by default
[ 0.745661] hpet0: at MMIO 0xfeff0000, IRQs 2, 8, 31
[ 0.745661] hpet0: 3 comparators, 32-bit 25.000000 MHz counter
[ 0.770008] Switching to clocksource tsc
[ 0.771728] pnp: PnP ACPI init
[ 0.771836] ACPI: bus type pnp registered
[ 0.775058] pnp: PnP ACPI: found 13 devices
[ 0.775153] ACPI: ACPI bus type pnp unregistered
[ 0.775256] system 00:00: ioport range 0x1000-0x107f has been reserved
[ 0.775360] system 00:00: ioport range 0x1080-0x10ff has been reserved
[ 0.775464] system 00:00: ioport range 0x1400-0x147f has been reserved
[ 0.775569] system 00:00: ioport range 0x1480-0x14ff has been reserved
[ 0.775673] system 00:00: ioport range 0x1800-0x187f has been reserved
[ 0.775777] system 00:00: ioport range 0x1880-0x18ff has been reserved
[ 0.775883] system 00:02: ioport range 0x4d0-0x4d1 has been reserved
[ 0.775987] system 00:02: ioport range 0x295-0x314 has been reserved
[ 0.776090] system 00:02: ioport range 0x880-0x88f has been reserved
[ 0.776200] system 00:0b: iomem range 0xe0000000-0xefffffff has been reserved
[ 0.776312] system 00:0c: iomem range 0xd0000-0xd3fff has been reserved
[ 0.776416] system 00:0c: iomem range 0xd5800-0xd7fff has been reserved
[ 0.776531] system 00:0c: iomem range 0xf0000-0xfbfff could not be reserved
[ 0.776637] system 00:0c: iomem range 0xfc000-0xfffff could not be reserved
[ 0.776743] system 00:0c: iomem range 0x7fef0000-0x7fefffff could not be reserved
[ 0.776883] system 00:0c: iomem range 0xffff0000-0xffffffff has been reserved
[ 0.776989] system 00:0c: iomem range 0x0-0x9ffff could not be reserved
[ 0.777094] system 00:0c: iomem range 0x100000-0x7feeffff could not be reserved
[ 0.777233] system 00:0c: iomem range 0xfec00000-0xfec00fff could not be reserved
[ 0.777373] system 00:0c: iomem range 0xd0000000-0xdfffffff has been reserved
[ 0.777480] system 00:0c: iomem range 0xfee00000-0xfee00fff has been reserved
[ 0.777587] system 00:0c: iomem range 0xfeff0000-0xfeff0000 has been reserved
[ 0.782391] pci 0000:00:03.0: PCI bridge, secondary bus 0000:01
[ 0.782493] pci 0000:00:03.0: IO window: 0x9000-0x9fff
[ 0.782593] pci 0000:00:03.0: MEM window: 0xca000000-0xcdffffff
[ 0.782696] pci 0000:00:03.0: PREFETCH window: 0x000000b0000000-0x000000bfffffff
[ 0.782838] pci 0000:00:0f.0: PCI bridge, secondary bus 0000:02
[ 0.782940] pci 0000:00:0f.0: IO window: 0x8000-0x8fff
[ 0.783040] pci 0000:00:0f.0: MEM window: 0xcfe00000-0xcfefffff
[ 0.783142] pci 0000:00:0f.0: PREFETCH window: disabled
[ 0.783243] pci 0000:00:18.0: PCI bridge, secondary bus 0000:03
[ 0.783344] pci 0000:00:18.0: IO window: 0x7000-0x7fff
[ 0.783444] pci 0000:00:18.0: MEM window: 0xc6000000-0xc9ffffff
[ 0.783547] pci 0000:00:18.0: PREFETCH window: 0x000000a0000000-0x000000afffffff
[ 0.783695] pci 0000:00:03.0: setting latency timer to 64
[ 0.783699] pci 0000:00:0f.0: setting latency timer to 64
[ 0.783705] pci 0000:00:18.0: setting latency timer to 64
[ 0.783709] pci_bus 0000:00: resource 0 io: [0x00-0xffff]
[ 0.783711] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffffffffffff]
[ 0.783713] pci_bus 0000:01: resource 0 io: [0x9000-0x9fff]
[ 0.783715] pci_bus 0000:01: resource 1 mem: [0xca000000-0xcdffffff]
[ 0.783717] pci_bus 0000:01: resource 2 pref mem [0xb0000000-0xbfffffff]
[ 0.783719] pci_bus 0000:02: resource 0 io: [0x8000-0x8fff]
[ 0.783721] pci_bus 0000:02: resource 1 mem: [0xcfe00000-0xcfefffff]
[ 0.783722] pci_bus 0000:02: resource 3 io: [0x00-0xffff]
[ 0.783724] pci_bus 0000:02: resource 4 mem: [0x000000-0xffffffffffffffff]
[ 0.783726] pci_bus 0000:03: resource 0 io: [0x7000-0x7fff]
[ 0.783728] pci_bus 0000:03: resource 1 mem: [0xc6000000-0xc9ffffff]
[ 0.783730] pci_bus 0000:03: resource 2 pref mem [0xa0000000-0xafffffff]
[ 0.783762] NET: Registered protocol family 2
[ 0.783968] IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.784668] TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
[ 0.786428] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.787074] TCP: Hash tables configured (established 262144 bind 65536)
[ 0.787178] TCP reno registered
[ 0.787402] NET: Registered protocol family 1
[ 0.809971] pci 0000:01:00.0: Boot video device
[ 0.810058] Trying to unpack rootfs image as initramfs...
[ 0.965719] Freeing initrd memory: 8333k freed
[ 0.971347] Scanning for low memory corruption every 60 seconds
[ 0.971618] audit: initializing netlink socket (disabled)
[ 0.971733] type=2000 audit(1264042925.967:1): initialized
[ 0.980142] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.981575] VFS: Disk quotas dquot_6.5.2
[ 0.981737] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.982356] fuse init (API version 7.13)
[ 0.982550] msgmni has been set to 4015
[ 0.983034] alg: No test for stdrng (krng)
[ 0.983148] io scheduler noop registered
[ 0.983246] io scheduler anticipatory registered
[ 0.983344] io scheduler deadline registered
[ 0.983487] io scheduler cfq registered (default)
[ 0.983711] alloc irq_desc for 24 on node -1
[ 0.983713] alloc kstat_irqs on node -1
[ 0.983722] pcieport 0000:00:03.0: irq 24 for MSI/MSI-X
[ 0.983727] pcieport 0000:00:03.0: setting latency timer to 64
[ 0.983819] alloc irq_desc for 25 on node -1
[ 0.983820] alloc kstat_irqs on node -1
[ 0.983826] pcieport 0000:00:18.0: irq 25 for MSI/MSI-X
[ 0.983831] pcieport 0000:00:18.0: setting latency timer to 64
[ 0.983893] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.984011] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 0.984243] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
[ 0.984388] ACPI: Power Button [PWRB]
[ 0.984532] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[ 0.984671] ACPI: Power Button [PWRF]
[ 0.985208] processor LNXCPU:00: registered as cooling_device0
[ 0.985357] processor LNXCPU:01: registered as cooling_device1
[ 0.986902] processor LNXCPU:02: registered as cooling_device2
[ 0.987034] processor LNXCPU:03: registered as cooling_device3
[ 0.990928] Linux agpgart interface v0.103
[ 0.991022] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.991220] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.991595] 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.992488] brd: module loaded
[ 0.992930] loop: module loaded
[ 0.993077] input: Macintosh mouse button emulation as /devices/virtual/input/input2
[ 0.993431] sata_nv 0000:00:0e.0: version 3.5
[ 0.993673] ACPI: PCI Interrupt Link [ASA0] enabled at IRQ 21
[ 0.993776] alloc irq_desc for 21 on node -1
[ 0.993778] alloc kstat_irqs on node -1
[ 0.993784] sata_nv 0000:00:0e.0: PCI INT A -> Link[ASA0] -> GSI 21 (level, low) -> IRQ 21
[ 0.993927] sata_nv 0000:00:0e.0: Using SWNCQ mode
[ 0.994253] sata_nv 0000:00:0e.0: setting latency timer to 64
[ 0.994397] scsi0 : sata_nv
[ 0.994596] scsi1 : sata_nv
[ 0.994825] ata1: SATA max UDMA/133 cmd 0x9f0 ctl 0xbf0 bmdma 0xd800 irq 21
[ 0.994932] ata2: SATA max UDMA/133 cmd 0x970 ctl 0xb70 bmdma 0xd808 irq 21
[ 0.995314] ACPI: PCI Interrupt Link [ASA1] enabled at IRQ 20
[ 0.995415] alloc irq_desc for 20 on node -1
[ 0.995417] alloc kstat_irqs on node -1
[ 0.995420] sata_nv 0000:00:0e.1: PCI INT B -> Link[ASA1] -> GSI 20 (level, low) -> IRQ 20
[ 0.995563] sata_nv 0000:00:0e.1: Using SWNCQ mode
[ 0.995684] sata_nv 0000:00:0e.1: setting latency timer to 64
[ 0.995826] scsi2 : sata_nv
[ 0.996011] scsi3 : sata_nv
[ 0.996238] ata3: SATA max UDMA/133 cmd 0x9e0 ctl 0xbe0 bmdma 0xc400 irq 20
[ 0.996345] ata4: SATA max UDMA/133 cmd 0x960 ctl 0xb60 bmdma 0xc408 irq 20
[ 0.996807] ACPI: PCI Interrupt Link [ASA2] enabled at IRQ 21
[ 0.996909] sata_nv 0000:00:0e.2: PCI INT C -> Link[ASA2] -> GSI 21 (level, low) -> IRQ 21
[ 0.997052] sata_nv 0000:00:0e.2: Using SWNCQ mode
[ 0.997176] sata_nv 0000:00:0e.2: setting latency timer to 64
[ 0.997304] scsi4 : sata_nv
[ 0.997488] scsi5 : sata_nv
[ 0.997722] ata5: SATA max UDMA/133 cmd 0xc000 ctl 0xbc00 bmdma 0xb000 irq 21
[ 0.997829] ata6: SATA max UDMA/133 cmd 0xb800 ctl 0xb400 bmdma 0xb008 irq 21
[ 0.998081] pata_amd 0000:00:0d.0: version 0.4.1
[ 0.998109] pata_amd 0000:00:0d.0: setting latency timer to 64
[ 0.998206] scsi6 : pata_amd
[ 0.998392] scsi7 : pata_amd
[ 0.998943] ata7: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xec00 irq 14
[ 0.999049] ata8: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xec08 irq 15
[ 0.999269] ata7: port disabled. ignoring.
[ 0.999787] Fixed MDIO Bus: probed
[ 0.999904] PPP generic driver version 2.4.2
[ 1.000064] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.000429] ACPI: PCI Interrupt Link [AUS2] enabled at IRQ 23
[ 1.000540] alloc irq_desc for 23 on node -1
[ 1.000542] alloc kstat_irqs on node -1
[ 1.000546] ehci_hcd 0000:00:0b.1: PCI INT B -> Link[AUS2] -> GSI 23 (level, low) -> IRQ 23
[ 1.000694] ehci_hcd 0000:00:0b.1: setting latency timer to 64
[ 1.000697] ehci_hcd 0000:00:0b.1: EHCI Host Controller
[ 1.000830] ehci_hcd 0000:00:0b.1: new USB bus registered, assigned bus number 1
[ 1.000986] ehci_hcd 0000:00:0b.1: debug port 1
[ 1.001087] ehci_hcd 0000:00:0b.1: cache line size of 32 is not supported
[ 1.001099] ehci_hcd 0000:00:0b.1: irq 23, io mem 0xcfffe000
[ 1.030051] ehci_hcd 0000:00:0b.1: USB 2.0 started, EHCI 1.00
[ 1.030244] usb usb1: configuration #1 chosen from 1 choice
[ 1.030376] hub 1-0:1.0: USB hub found
[ 1.030473] hub 1-0:1.0: 10 ports detected
[ 1.030616] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.030960] ACPI: PCI Interrupt Link [AUBA] enabled at IRQ 22
[ 1.031061] alloc irq_desc for 22 on node -1
[ 1.031062] alloc kstat_irqs on node -1
[ 1.031066] ohci_hcd 0000:00:0b.0: PCI INT A -> Link[AUBA] -> GSI 22 (level, low) -> IRQ 22
[ 1.031215] ohci_hcd 0000:00:0b.0: setting latency timer to 64
[ 1.031217] ohci_hcd 0000:00:0b.0: OHCI Host Controller
[ 1.031359] ohci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 2
[ 1.031515] ohci_hcd 0000:00:0b.0: irq 22, io mem 0xcffff000
[ 1.082177] usb usb2: configuration #1 chosen from 1 choice
[ 1.082295] hub 2-0:1.0: USB hub found
[ 1.082394] hub 2-0:1.0: 10 ports detected
[ 1.082539] uhci_hcd: USB Universal Host Controller Interface driver
[ 1.082730] PNP: No PS/2 controller found. Probing ports directly.
[ 1.085452] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.085552] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 1.085734] mice: PS/2 mouse device common for all mice
[ 1.085896] Driver 'rtc_cmos' needs updating - please use bus_type methods
[ 1.086036] rtc_cmos 00:05: RTC can wake from S4
[ 1.086157] rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
[ 1.086286] rtc0: alarms up to one year, y3k, 114 bytes nvram, hpet irqs
[ 1.086480] device-mapper: uevent: version 1.0.3
[ 1.086696] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
[ 1.087084] device-mapper: multipath: version 1.1.0 loaded
[ 1.087194] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 1.087783] cpuidle: using governor ladder
[ 1.087898] cpuidle: using governor menu
[ 1.088301] TCP cubic registered
[ 1.088481] NET: Registered protocol family 10
[ 1.088970] lo: Disabled Privacy Extensions
[ 1.089314] NET: Registered protocol family 17
[ 1.089422] Bluetooth: L2CAP ver 2.14
[ 1.089513] Bluetooth: L2CAP socket layer initialized
[ 1.089611] Bluetooth: SCO (Voice Link) ver 0.6
[ 1.089706] Bluetooth: SCO socket layer initialized
[ 1.089870] Bluetooth: RFCOMM TTY layer initialized
[ 1.089981] Bluetooth: RFCOMM socket layer initialized
[ 1.090083] Bluetooth: RFCOMM ver 1.11
[ 1.090268] PM: Resume from disk failed.
[ 1.090287] registered taskstats version 1
[ 1.090776] Magic number: 10:821:7
[ 1.090941] rtc_cmos 00:05: setting system clock to 2010-01-21 03:02:06 UTC (1264042926)
[ 1.091094] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 1.091195] EDD information not available.
[ 1.333101] ata1: SATA link down (SStatus 0 SControl 300)
[ 1.400043] hub 1-0:1.0: unable to enumerate USB device on port 6
[ 1.480076] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1.492554] ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1.502797] ata3.00: ATAPI: TSSTcorpCD/DVDW SH-S183L, SB01, max UDMA/33
[ 1.502906] ata3.00: applying bridge limits
[ 1.503274] ata5.00: ATA-8: Hitachi HDS722020ALA330, JKAOA20N, max UDMA/133
[ 1.503385] ata5.00: 3907029168 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 1.540202] ata3.00: configured for UDMA/33
[ 1.550405] ata5.00: configured for UDMA/133
[ 1.670538] ata2: SATA link down (SStatus 0 SControl 300)
[ 1.671640] scsi 2:0:0:0: CD-ROM TSSTcorp CD/DVDW SH-S183L SB01 PQ: 0 ANSI: 5
[ 1.678541] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[ 1.678685] Uniform CD-ROM driver Revision: 3.20
[ 1.678857] sr 2:0:0:0: Attached scsi CD-ROM sr0
[ 1.678889] sr 2:0:0:0: Attached scsi generic sg0 type 5
[ 1.740037] usb 2-5: new low speed USB device using ohci_hcd and address 2
[ 1.968265] usb 2-5: configuration #1 chosen from 1 choice
[ 2.160147] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 2.180165] ata4.00: ATAPI: ATAPI iHOS104, WL0B, max UDMA/100
[ 2.220176] ata4.00: configured for UDMA/100
[ 3.340035] usb 2-6: new full speed USB device using ohci_hcd and address 3
[ 3.577376] usb 2-6: configuration #1 chosen from 1 choice
[ 7.220071] ata4.00: qc timeout (cmd 0xa0)
[ 7.220170] ata4.00: TEST_UNIT_READY failed (err_mask=0x5)
[ 7.710065] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 7.770176] ata4.00: configured for UDMA/100
[ 12.770056] ata4.00: qc timeout (cmd 0xa0)
[ 12.770154] ata4.00: TEST_UNIT_READY failed (err_mask=0x5)
[ 12.770258] ata4: limiting SATA link speed to 1.5 Gbps
[ 12.770357] ata4.00: limiting speed to UDMA/100:PIO3
[ 13.260064] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 13.320176] ata4.00: configured for UDMA/100
[ 18.320078] ata4.00: qc timeout (cmd 0xa0)
[ 18.320177] ata4.00: TEST_UNIT_READY failed (err_mask=0x5)
[ 18.320280] ata4.00: disabled
[ 18.320387] ata4: hard resetting link
[ 18.320478] ata4: nv: skipping hardreset on occupied port
[ 18.810064] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 18.810175] ata4: EH complete
[ 18.810408] scsi 4:0:0:0: Direct-Access ATA Hitachi HDS72202 JKAO PQ: 0 ANSI: 5
[ 18.810662] sd 4:0:0:0: Attached scsi generic sg1 type 0
[ 18.810831] sd 4:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
[ 18.811007] sd 4:0:0:0: [sda] Write Protect is off
[ 18.811104] sd 4:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 18.811124] sd 4:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 18.811373] sda: sda1
[ 18.821698] sd 4:0:0:0: [sda] Attached SCSI disk
[ 19.300065] ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 19.359025] ata6.00: ATA-7: ST3320620AS, 3.AAD, max UDMA/133
[ 19.359130] ata6.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 19.442328] ata6.00: configured for UDMA/133
[ 19.442530] scsi 5:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5
[ 19.442839] sd 5:0:0:0: [sdb] 625142448 512-byte logical blocks: (320 GB/298 GiB)
[ 19.442858] sd 5:0:0:0: Attached scsi generic sg2 type 0
[ 19.442980] ata8: port disabled. ignoring.
[ 19.443138] sd 5:0:0:0: [sdb] Write Protect is off
[ 19.443235] sd 5:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 19.443254] sd 5:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 19.443494] sdb: sdb1 sdb2 < sdb5 >
[ 19.502615] sd 5:0:0:0: [sdb] Attached SCSI disk
[ 19.502753] Freeing unused kernel memory: 728k freed
[ 19.503174] Write protecting the kernel read-only data: 7792k
[ 19.617921] forcedeth: Reverse Engineered nForce ethernet driver. Version 0.64.
[ 19.628019] FDC 0 is a post-1991 82077
[ 19.633878] ACPI: PCI Interrupt Link [AMAC] enabled at IRQ 23
[ 19.633992] forcedeth 0000:00:11.0: PCI INT A -> Link[AMAC] -> GSI 23 (level, low) -> IRQ 23
[ 19.634143] forcedeth 0000:00:11.0: setting latency timer to 64
[ 19.634229] nv_probe: set workaround bit for reversed mac addr
[ 19.642594] usbcore: registered new interface driver hiddev
[ 19.644913] ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
[ 19.645019] alloc irq_desc for 19 on node -1
[ 19.645021] alloc kstat_irqs on node -1
[ 19.645027] ohci1394 0000:02:07.0: PCI INT A -> Link[APC4] -> GSI 19 (level, low) -> IRQ 19
[ 19.649791] input: Ideazon Zboard Gaming Keyboard as /devices/pci0000:00/0000:00:0b.0/usb2/2-5/2-5:1.0/input/input3
[ 19.649997] generic-usb 0003:1038:0210.0001: input,hidraw0: USB HID v1.11 Keyboard [Ideazon Zboard Gaming Keyboard] on usb-0000:00:0b.0-5/input0
[ 19.663513] input: Ideazon Zboard Gaming Keyboard as /devices/pci0000:00/0000:00:0b.0/usb2/2-5/2-5:1.1/input/input4
[ 19.665305] generic-usb 0003:1038:0210.0002: input,hiddev96,hidraw1: USB HID v1.11 Device [Ideazon Zboard Gaming Keyboard] on usb-0000:00:0b.0-5/input1
[ 19.674574] input: Razer Razer Copperhead Laser Mouse as /devices/pci0000:00/0000:00:0b.0/usb2/2-6/2-6:1.0/input/input5
[ 19.674891] generic-usb 0003:1532:0101.0003: input,hidraw2: USB HID v1.00 Mouse [Razer Razer Copperhead Laser Mouse] on usb-0000:00:0b.0-6/input0
[ 19.680781] input: Razer Razer Copperhead Laser Mouse as /devices/pci0000:00/0000:00:0b.0/usb2/2-6/2-6:1.1/input/input6
[ 19.681022] generic-usb 0003:1532:0101.0004: input,hidraw3: USB HID v0.01 Keyboard [Razer Razer Copperhead Laser Mouse] on usb-0000:00:0b.0-6/input1
[ 19.681206] usbcore: registered new interface driver usbhid
[ 19.681333] usbhid: v2.6:USB HID core driver
[ 19.710109] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[19] MMIO=[cfeff000-cfeff7ff] Max Packet=[2048] IR/IT contexts=[4/8]
[ 20.170793] forcedeth 0000:00:11.0: ifname eth0, PHY OUI 0x5043 @ 1, addr 00:04:4b:05:cb:6c
[ 20.170939] forcedeth 0000:00:11.0: highdma csum vlan pwrctl mgmt gbit lnktim msi desc-v3
[ 20.171381] ACPI: PCI Interrupt Link [AMA1] enabled at IRQ 22
[ 20.171484] forcedeth 0000:00:12.0: PCI INT A -> Link[AMA1] -> GSI 22 (level, low) -> IRQ 22
[ 20.171630] forcedeth 0000:00:12.0: setting latency timer to 64
[ 20.171671] nv_probe: set workaround bit for reversed mac addr
[ 20.710814] forcedeth 0000:00:12.0: ifname eth1, PHY OUI 0x5043 @ 2, addr 00:04:4b:05:cb:6d
[ 20.710959] forcedeth 0000:00:12.0: highdma csum vlan pwrctl mgmt gbit lnktim msi desc-v3
[ 20.912561] PM: Starting manual resume from disk
[ 20.912660] PM: Resume from partition 8:21
[ 20.912661] PM: Checking hibernation image.
[ 20.912831] PM: Error -22 checking image file
[ 20.912834] PM: Resume from disk failed.
[ 20.957919] EXT4-fs (sdb1): mounted filesystem with ordered data mode
[ 21.033993] ieee1394: Host added: ID:BUS[0-00:1023] GUID[1aa25f0500044b06]
[ 35.717547] udev: starting version 147
[ 35.793302] Adding 6024332k swap on /dev/sdb5. Priority:-1 extents:1 across:6024332k
[ 36.389181] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 36.389748] lp: driver loaded but no devices found
[ 36.836983] nvidia: module license 'NVIDIA' taints kernel.
[ 36.836987] Disabling lock debugging due to kernel taint
[ 36.946291] alloc irq_desc for 26 on node -1
[ 36.946293] alloc kstat_irqs on node -1
[ 36.946302] forcedeth 0000:00:11.0: irq 26 for MSI/MSI-X
[ 36.946493] eth0: no link during initialization.
[ 36.947077] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 37.069628] i2c i2c-0: nForce2 SMBus adapter at 0xf400
[ 37.069680] i2c i2c-1: nForce2 SMBus adapter at 0xf000
[ 37.305950] ACPI: PCI Interrupt Link [AXV5] enabled at IRQ 16
[ 37.305955] alloc irq_desc for 16 on node -1
[ 37.305957] alloc kstat_irqs on node -1
[ 37.305964] nvidia 0000:01:00.0: PCI INT A -> Link[AXV5] -> GSI 16 (level, low) -> IRQ 16
[ 37.305970] nvidia 0000:01:00.0: setting latency timer to 64
[ 37.306095] nvidia 0000:03:00.0: enabling device (0000 -> 0003)
[ 37.306100] nvidia 0000:03:00.0: PCI INT A -> Link[AXV5] -> GSI 16 (level, low) -> IRQ 16
[ 37.306105] nvidia 0000:03:00.0: setting latency timer to 64
[ 37.306328] NVRM: loading NVIDIA UNIX x86_64 Kernel Module 185.18.36 Fri Aug 14 17:35:21 PDT 2009
[ 37.355499] alloc irq_desc for 27 on node -1
[ 37.355503] alloc kstat_irqs on node -1
[ 37.355511] forcedeth 0000:00:12.0: irq 27 for MSI/MSI-X
[ 37.868744] ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17
[ 37.868754] alloc irq_desc for 17 on node -1
[ 37.868757] alloc kstat_irqs on node -1
[ 37.868765] CA0106 0000:02:09.0: PCI INT A -> Link[APC2] -> GSI 17 (level, low) -> IRQ 17
[ 37.868795] snd-ca0106: Model 1011 Rev 00000000 Serial 10111102
[ 37.919784] ACPI: PCI Interrupt Link [AAZA] enabled at IRQ 23
[ 37.919790] HDA Intel 0000:00:0f.1: PCI INT B -> Link[AAZA] -> GSI 23 (level, low) -> IRQ 23
[ 37.919812] HDA Intel 0000:00:0f.1: setting latency timer to 64
[ 39.313897] hda_codec: ALC889A: BIOS auto-probing.
[ 39.930353] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:0f.1/input/input7
[ 40.451592] vboxdrv: Trying to deactivate the NMI watchdog permanently...
[ 40.451597] vboxdrv: Successfully done.
[ 40.451599] vboxdrv: Found 4 processor cores.
[ 40.451951] VBoxDrv: dbg - g_abExecMemory=ffffffffa0cae460
[ 40.452063] vboxdrv: fAsync=0 offMin=0x4d8 offMax=0x904c
[ 40.452470] vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
[ 40.452472] vboxdrv: Successfully loaded version 3.0.12 (interface 0x00110000).
[ 40.657930] VBoxNetFlt: dbg - g_abExecMemory=ffffffffa0e4c260
[ 40.660228] VBoxNetAdp: dbg - g_abExecMemory=ffffffffa0e64b00
[ 40.835606] Bridge firewalling registered
[ 40.842382] device eth0 entered promiscuous mode
[ 40.842978] virbr0: starting userspace STP failed, starting kernel STP
[ 40.848310] ppdev: user-space parallel port driver
[ 40.943194] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 40.943742] CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
[ 40.943745] nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
[ 40.943746] sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
[ 41.754059] lo: Disabled Privacy Extensions
[ 42.564751] RPC: Registered udp transport module.
[ 42.564755] RPC: Registered tcp transport module.
[ 42.564756] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 42.702798] svc: failed to register lockdv1 RPC service (errno 97).
[ 48.230183] eth1: no IPv6 routers present
[ 51.582531] br0: no IPv6 routers present
[-- Attachment #3: boot.2.6.32.swncq.disabled.log --]
[-- Type: text/x-log, Size: 47370 bytes --]
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.32-020632-generic (root@zinc) (gcc version 4.2.3 (Ubuntu 4.2.3-2ubuntu7)) #020632 SMP Thu Dec 3 10:09:58 UTC 2009
[ 0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-2.6.32-020632-generic root=UUID=2e50af70-690f-48f4-a8e8-32472593f9d7 ro sata_nv.swncq=0
[ 0.000000] KERNEL supported cpus:
[ 0.000000] Intel GenuineIntel
[ 0.000000] AMD AuthenticAMD
[ 0.000000] Centaur CentaurHauls
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009b800 (usable)
[ 0.000000] BIOS-e820: 000000000009b800 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000007fef0000 (usable)
[ 0.000000] BIOS-e820: 000000007fef0000 - 000000007fef3000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000007fef3000 - 000000007ff00000 (ACPI data)
[ 0.000000] BIOS-e820: 00000000d0000000 - 00000000f0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
[ 0.000000] DMI 2.4 present.
[ 0.000000] Phoenix BIOS detected: BIOS may corrupt low RAM, working around it.
[ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[ 0.000000] last_pfn = 0x7fef0 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-CBFFF write-protect
[ 0.000000] CC000-FFFFF uncachable
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000 mask F80000000 write-back
[ 0.000000] 1 base 07FF00000 mask FFFF00000 uncachable
[ 0.000000] 2 disabled
[ 0.000000] 3 disabled
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] Scanning 0 areas for low memory corruption
[ 0.000000] modified physical RAM map:
[ 0.000000] modified: 0000000000000000 - 0000000000010000 (reserved)
[ 0.000000] modified: 0000000000010000 - 000000000009b800 (usable)
[ 0.000000] modified: 000000000009b800 - 00000000000a0000 (reserved)
[ 0.000000] modified: 00000000000f0000 - 0000000000100000 (reserved)
[ 0.000000] modified: 0000000000100000 - 000000007fef0000 (usable)
[ 0.000000] modified: 000000007fef0000 - 000000007fef3000 (ACPI NVS)
[ 0.000000] modified: 000000007fef3000 - 000000007ff00000 (ACPI data)
[ 0.000000] modified: 00000000d0000000 - 00000000f0000000 (reserved)
[ 0.000000] modified: 00000000fec00000 - 0000000100000000 (reserved)
[ 0.000000] initial memory mapped : 0 - 20000000
[ 0.000000] init_memory_mapping: 0000000000000000-000000007fef0000
[ 0.000000] 0000000000 - 007fe00000 page 2M
[ 0.000000] 007fe00000 - 007fef0000 page 4k
[ 0.000000] kernel direct mapping tables up to 7fef0000 @ 10000-14000
[ 0.000000] RAMDISK: 377cc000 - 37fef7b0
[ 0.000000] ACPI: RSDP 00000000000f7fa0 00014 (v00 Nvidia)
[ 0.000000] ACPI: RSDT 000000007fef3040 00038 (v01 Nvidia NVDAACPI 42302E31 NVDA 00000000)
[ 0.000000] ACPI: FACP 000000007fef30c0 00074 (v01 Nvidia NVDAACPI 42302E31 NVDA 00000000)
[ 0.000000] ACPI: DSDT 000000007fef3180 0541D (v01 NVIDIA NVDAACPI 00001000 MSFT 03000000)
[ 0.000000] ACPI: FACS 000000007fef0000 00040
[ 0.000000] ACPI: HPET 000000007fef8700 00038 (v01 Nvidia NVDAACPI 42302E31 NVDA 00000098)
[ 0.000000] ACPI: WDRT 000000007fef8780 00047 (v01 Nvidia NVDAACPI 42302E31 NVDA 00000000)
[ 0.000000] ACPI: MCFG 000000007fef8840 0003C (v01 Nvidia NVDAACPI 42302E31 NVDA 00000000)
[ 0.000000] ACPI: APIC 000000007fef8600 00098 (v01 Nvidia NVDAACPI 42302E31 NVDA 00000000)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at 0000000000000000-000000007fef0000
[ 0.000000] Bootmem setup node 0 0000000000000000-000000007fef0000
[ 0.000000] NODE_DATA [0000000000012000 - 0000000000016fff]
[ 0.000000] bootmap [0000000000017000 - 0000000000026fdf] pages 10
[ 0.000000] (7 early reservations) ==> bootmem [0000000000 - 007fef0000]
[ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
[ 0.000000] #1 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000]
[ 0.000000] #2 [0001000000 - 0001a2f784] TEXT DATA BSS ==> [0001000000 - 0001a2f784]
[ 0.000000] #3 [00377cc000 - 0037fef7b0] RAMDISK ==> [00377cc000 - 0037fef7b0]
[ 0.000000] #4 [000009b800 - 0000100000] BIOS reserved ==> [000009b800 - 0000100000]
[ 0.000000] #5 [0001a30000 - 0001a300b2] BRK ==> [0001a30000 - 0001a300b2]
[ 0.000000] #6 [0000010000 - 0000012000] PGTABLE ==> [0000010000 - 0000012000]
[ 0.000000] found SMP MP-table at [ffff8800000f3fd0] f3fd0
[ 0.000000] [ffffea0000000000-ffffea0001bfffff] PMD -> [ffff880002000000-ffff880003bfffff] on node 0
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000010 -> 0x00001000
[ 0.000000] DMA32 0x00001000 -> 0x00100000
[ 0.000000] Normal 0x00100000 -> 0x00100000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[2] active PFN ranges
[ 0.000000] 0: 0x00000010 -> 0x0000009b
[ 0.000000] 0: 0x00000100 -> 0x0007fef0
[ 0.000000] On node 0 totalpages: 523899
[ 0.000000] DMA zone: 56 pages used for memmap
[ 0.000000] DMA zone: 105 pages reserved
[ 0.000000] DMA zone: 3818 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 7109 pages used for memmap
[ 0.000000] DMA32 zone: 512811 pages, LIFO batch:31
[ 0.000000] ACPI: PM-Timer IO Port: 0x1008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x03] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 4, version 17, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] ACPI: IRQ14 used by override.
[ 0.000000] ACPI: IRQ15 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x10de8201 base: 0xfeff0000
[ 0.000000] SMP: Allowing 4 CPUs, 0 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 24
[ 0.000000] PM: Registered nosave memory: 000000000009b000 - 000000000009c000
[ 0.000000] PM: Registered nosave memory: 000000000009c000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
[ 0.000000] PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
[ 0.000000] Allocating PCI resources starting at 7ff00000 (gap: 7ff00000:50100000)
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] NR_CPUS:64 nr_cpumask_bits:64 nr_cpu_ids:4 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 30 pages/cpu @ffff880001c00000 s91288 r8192 d23400 u524288
[ 0.000000] pcpu-alloc: s91288 r8192 d23400 u524288 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1 2 3
[ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 516629
[ 0.000000] Policy zone: DMA32
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.32-020632-generic root=UUID=2e50af70-690f-48f4-a8e8-32472593f9d7 ro sata_nv.swncq=0
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Initializing CPU#0
[ 0.000000] Checking aperture...
[ 0.000000] No AGP bridge found
[ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
[ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[ 0.000000] Memory: 2047508k/2096064k available (5355k kernel code, 468k absent, 48088k reserved, 3200k data, 728k init)
[ 0.000000] SLUB: Genslabs=14, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:4352 nr_irqs:440
[ 0.000000] spurious 8259A interrupt: IRQ7.
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] allocated 20971520 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] hpet clockevent registered
[ 0.000000] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 2666.461 MHz processor.
[ 0.010008] Calibrating delay loop (skipped), value calculated using timer frequency.. 5332.92 BogoMIPS (lpj=26664610)
[ 0.010232] Security Framework initialized
[ 0.010333] SELinux: Disabled at boot.
[ 0.010580] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.012289] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.013057] Mount-cache hash table entries: 256
[ 0.013316] Initializing cgroup subsys ns
[ 0.013412] Initializing cgroup subsys cpuacct
[ 0.013509] Initializing cgroup subsys memory
[ 0.013609] Initializing cgroup subsys freezer
[ 0.013704] Initializing cgroup subsys net_cls
[ 0.013818] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.013958] CPU: L2 cache: 4096K
[ 0.014049] CPU 0/0x0 -> Node 0
[ 0.014138] CPU: Physical Processor ID: 0
[ 0.014231] CPU: Processor Core ID: 0
[ 0.014324] mce: CPU supports 6 MCE banks
[ 0.014422] CPU0: Thermal monitoring enabled (TM1)
[ 0.014521] using mwait in idle threads.
[ 0.014613] Performance Events: Core2 events, Intel PMU driver.
[ 0.014805] ... version: 2
[ 0.014898] ... bit width: 40
[ 0.014990] ... generic registers: 2
[ 0.015083] ... value mask: 000000ffffffffff
[ 0.015181] ... max period: 000000007fffffff
[ 0.015279] ... fixed-purpose events: 3
[ 0.015371] ... event mask: 0000000700000003
[ 0.017684] ACPI: Core revision 20090903
[ 0.026870] Setting APIC routing to flat
[ 0.027366] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.127484] CPU0: Intel(R) Core(TM)2 Quad CPU @ 2.66GHz stepping 07
[ 0.130000] Booting processor 1 APIC 0x1 ip 0x6000
[ 0.020000] Initializing CPU#1
[ 0.020000] Calibrating delay using timer specific routine.. 5333.32 BogoMIPS (lpj=26666644)
[ 0.020000] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.020000] CPU: L2 cache: 4096K
[ 0.020000] CPU 1/0x1 -> Node 0
[ 0.020000] CPU: Physical Processor ID: 0
[ 0.020000] CPU: Processor Core ID: 1
[ 0.020000] CPU1: Thermal monitoring enabled (TM1)
[ 0.280118] CPU1: Intel(R) Core(TM)2 Quad CPU @ 2.66GHz stepping 07
[ 0.281089] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[ 0.290113] Booting processor 2 APIC 0x3 ip 0x6000
[ 0.020000] Initializing CPU#2
[ 0.020000] Calibrating delay using timer specific routine.. 5333.29 BogoMIPS (lpj=26666472)
[ 0.020000] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.020000] CPU: L2 cache: 4096K
[ 0.020000] CPU 2/0x3 -> Node 0
[ 0.020000] CPU: Physical Processor ID: 0
[ 0.020000] CPU: Processor Core ID: 3
[ 0.020000] CPU2: Thermal monitoring enabled (TM1)
[ 0.450055] CPU2: Intel(R) Core(TM)2 Quad CPU @ 2.66GHz stepping 07
[ 0.451027] checking TSC synchronization [CPU#0 -> CPU#2]: passed.
[ 0.460081] Booting processor 3 APIC 0x2 ip 0x6000
[ 0.020000] Initializing CPU#3
[ 0.020000] Calibrating delay using timer specific routine.. 5333.28 BogoMIPS (lpj=26666432)
[ 0.020000] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.020000] CPU: L2 cache: 4096K
[ 0.020000] CPU 3/0x2 -> Node 0
[ 0.020000] CPU: Physical Processor ID: 0
[ 0.020000] CPU: Processor Core ID: 2
[ 0.020000] CPU3: Thermal monitoring enabled (TM1)
[ 0.620052] CPU3: Intel(R) Core(TM)2 Quad CPU @ 2.66GHz stepping 07
[ 0.622432] checking TSC synchronization [CPU#0 -> CPU#3]: passed.
[ 0.630011] Brought up 4 CPUs
[ 0.630103] Total of 4 processors activated (21332.83 BogoMIPS).
[ 0.631660] CPU0 attaching sched-domain:
[ 0.631663] domain 0: span 0-1 level MC
[ 0.631665] groups: 0 1
[ 0.631669] domain 1: span 0-3 level CPU
[ 0.631671] groups: 0-1 (cpu_power = 2048) 2-3 (cpu_power = 2048)
[ 0.631677] CPU1 attaching sched-domain:
[ 0.631679] domain 0: span 0-1 level MC
[ 0.631680] groups: 1 0
[ 0.631683] domain 1: span 0-3 level CPU
[ 0.631685] groups: 0-1 (cpu_power = 2048) 2-3 (cpu_power = 2048)
[ 0.631690] CPU2 attaching sched-domain:
[ 0.631692] domain 0: span 2-3 level MC
[ 0.631693] groups: 2 3
[ 0.631696] domain 1: span 0-3 level CPU
[ 0.631698] groups: 2-3 (cpu_power = 2048) 0-1 (cpu_power = 2048)
[ 0.631703] CPU3 attaching sched-domain:
[ 0.631704] domain 0: span 2-3 level MC
[ 0.631706] groups: 3 2
[ 0.631709] domain 1: span 0-3 level CPU
[ 0.631710] groups: 2-3 (cpu_power = 2048) 0-1 (cpu_power = 2048)
[ 0.631852] regulator: core version 0.5
[ 0.631852] Time: 2:51:46 Date: 01/21/10
[ 0.631852] NET: Registered protocol family 16
[ 0.631852] ACPI: bus type pci registered
[ 0.631852] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
[ 0.631852] PCI: MCFG area at e0000000 reserved in E820
[ 0.632975] PCI: Using MMCONFIG at e0000000 - efffffff
[ 0.633072] PCI: Using configuration type 1 for base access
[ 0.633806] bio: create slab <bio-0> at 0
[ 0.640070] ACPI: EC: Look up EC in DSDT
[ 0.646125] ACPI: Interpreter enabled
[ 0.646238] ACPI: (supports S0 S1 S3 S4 S5)
[ 0.646571] ACPI: Using IOAPIC for interrupt routing
[ 0.646873] ACPI: BIOS _OSI(Linux) query ignored
[ 0.654035] ACPI: No dock devices found.
[ 0.654254] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.655162] pci 0000:00:03.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.655267] pci 0000:00:03.0: PME# disabled
[ 0.655544] pci 0000:00:0a.0: reg 10 io port: [0xfc00-0xfc7f]
[ 0.655593] pci 0000:00:0a.1: reg 10 io port: [0xf800-0xf83f]
[ 0.655608] pci 0000:00:0a.1: reg 20 io port: [0xf400-0xf43f]
[ 0.655613] pci 0000:00:0a.1: reg 24 io port: [0xf000-0xf03f]
[ 0.655636] pci 0000:00:0a.1: PME# supported from D3hot D3cold
[ 0.655741] pci 0000:00:0a.1: PME# disabled
[ 0.655865] pci 0000:00:0b.0: reg 10 32bit mmio: [0xcffff000-0xcfffffff]
[ 0.655895] pci 0000:00:0b.0: supports D1 D2
[ 0.655896] pci 0000:00:0b.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.656002] pci 0000:00:0b.0: PME# disabled
[ 0.656120] pci 0000:00:0b.1: reg 10 32bit mmio: [0xcfffe000-0xcfffe0ff]
[ 0.656151] pci 0000:00:0b.1: supports D1 D2
[ 0.656153] pci 0000:00:0b.1: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.656258] pci 0000:00:0b.1: PME# disabled
[ 0.656390] pci 0000:00:0d.0: reg 20 io port: [0xec00-0xec0f]
[ 0.656433] pci 0000:00:0e.0: reg 10 io port: [0x9f0-0x9f7]
[ 0.656437] pci 0000:00:0e.0: reg 14 io port: [0xbf0-0xbf3]
[ 0.656441] pci 0000:00:0e.0: reg 18 io port: [0x970-0x977]
[ 0.656445] pci 0000:00:0e.0: reg 1c io port: [0xb70-0xb73]
[ 0.656450] pci 0000:00:0e.0: reg 20 io port: [0xd800-0xd80f]
[ 0.656454] pci 0000:00:0e.0: reg 24 32bit mmio: [0xcfffd000-0xcfffdfff]
[ 0.656501] pci 0000:00:0e.1: reg 10 io port: [0x9e0-0x9e7]
[ 0.656506] pci 0000:00:0e.1: reg 14 io port: [0xbe0-0xbe3]
[ 0.656510] pci 0000:00:0e.1: reg 18 io port: [0x960-0x967]
[ 0.656514] pci 0000:00:0e.1: reg 1c io port: [0xb60-0xb63]
[ 0.656518] pci 0000:00:0e.1: reg 20 io port: [0xc400-0xc40f]
[ 0.656523] pci 0000:00:0e.1: reg 24 32bit mmio: [0xcfffc000-0xcfffcfff]
[ 0.656570] pci 0000:00:0e.2: reg 10 io port: [0xc000-0xc007]
[ 0.656574] pci 0000:00:0e.2: reg 14 io port: [0xbc00-0xbc03]
[ 0.656579] pci 0000:00:0e.2: reg 18 io port: [0xb800-0xb807]
[ 0.656583] pci 0000:00:0e.2: reg 1c io port: [0xb400-0xb403]
[ 0.656587] pci 0000:00:0e.2: reg 20 io port: [0xb000-0xb00f]
[ 0.656592] pci 0000:00:0e.2: reg 24 32bit mmio: [0xcfffb000-0xcfffbfff]
[ 0.656689] pci 0000:00:0f.1: reg 10 32bit mmio: [0xcfff0000-0xcfff3fff]
[ 0.656723] pci 0000:00:0f.1: PME# supported from D3hot D3cold
[ 0.656826] pci 0000:00:0f.1: PME# disabled
[ 0.656966] pci 0000:00:11.0: reg 10 32bit mmio: [0xcfffa000-0xcfffafff]
[ 0.656970] pci 0000:00:11.0: reg 14 io port: [0xac00-0xac07]
[ 0.656975] pci 0000:00:11.0: reg 18 32bit mmio: [0xcfff9000-0xcfff90ff]
[ 0.656979] pci 0000:00:11.0: reg 1c 32bit mmio: [0xcfff8000-0xcfff800f]
[ 0.657009] pci 0000:00:11.0: supports D1 D2
[ 0.657011] pci 0000:00:11.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.657117] pci 0000:00:11.0: PME# disabled
[ 0.657250] pci 0000:00:12.0: reg 10 32bit mmio: [0xcfff7000-0xcfff7fff]
[ 0.657255] pci 0000:00:12.0: reg 14 io port: [0xa800-0xa807]
[ 0.657259] pci 0000:00:12.0: reg 18 32bit mmio: [0xcfff6000-0xcfff60ff]
[ 0.657264] pci 0000:00:12.0: reg 1c 32bit mmio: [0xcfff5000-0xcfff500f]
[ 0.657294] pci 0000:00:12.0: supports D1 D2
[ 0.657296] pci 0000:00:12.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.657402] pci 0000:00:12.0: PME# disabled
[ 0.657560] pci 0000:00:18.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.657665] pci 0000:00:18.0: PME# disabled
[ 0.657798] pci 0000:01:00.0: reg 10 32bit mmio: [0xcc000000-0xccffffff]
[ 0.657806] pci 0000:01:00.0: reg 14 64bit mmio pref: [0xb0000000-0xbfffffff]
[ 0.657813] pci 0000:01:00.0: reg 1c 64bit mmio: [0xca000000-0xcbffffff]
[ 0.657818] pci 0000:01:00.0: reg 24 io port: [0x9c00-0x9c7f]
[ 0.657822] pci 0000:01:00.0: reg 30 32bit mmio pref: [0x000000-0x01ffff]
[ 0.657882] pci 0000:00:03.0: bridge io port: [0x9000-0x9fff]
[ 0.657884] pci 0000:00:03.0: bridge 32bit mmio: [0xca000000-0xcdffffff]
[ 0.657888] pci 0000:00:03.0: bridge 64bit mmio pref: [0xb0000000-0xbfffffff]
[ 0.657923] pci 0000:02:07.0: reg 10 32bit mmio: [0xcfeff000-0xcfeff7ff]
[ 0.657929] pci 0000:02:07.0: reg 14 32bit mmio: [0xcfef8000-0xcfefbfff]
[ 0.657964] pci 0000:02:07.0: supports D1 D2
[ 0.657965] pci 0000:02:07.0: PME# supported from D0 D1 D2 D3hot
[ 0.658068] pci 0000:02:07.0: PME# disabled
[ 0.658188] pci 0000:02:09.0: reg 10 io port: [0x8c00-0x8c1f]
[ 0.658224] pci 0000:02:09.0: supports D1 D2
[ 0.658253] pci 0000:00:0f.0: transparent bridge
[ 0.658349] pci 0000:00:0f.0: bridge io port: [0x8000-0x8fff]
[ 0.658352] pci 0000:00:0f.0: bridge 32bit mmio: [0xcfe00000-0xcfefffff]
[ 0.658381] pci 0000:03:00.0: reg 10 32bit mmio: [0xc8000000-0xc8ffffff]
[ 0.658390] pci 0000:03:00.0: reg 14 64bit mmio pref: [0xa0000000-0xafffffff]
[ 0.658398] pci 0000:03:00.0: reg 1c 64bit mmio: [0xc6000000-0xc7ffffff]
[ 0.658403] pci 0000:03:00.0: reg 24 io port: [0x7c00-0x7c7f]
[ 0.658408] pci 0000:03:00.0: reg 30 32bit mmio pref: [0x000000-0x01ffff]
[ 0.658473] pci 0000:00:18.0: bridge io port: [0x7000-0x7fff]
[ 0.658476] pci 0000:00:18.0: bridge 32bit mmio: [0xc6000000-0xc9ffffff]
[ 0.658480] pci 0000:00:18.0: bridge 64bit mmio pref: [0xa0000000-0xafffffff]
[ 0.658492] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.658805] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
[ 0.723767] ACPI: PCI Interrupt Link [LNK1] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[ 0.724507] ACPI: PCI Interrupt Link [LNK2] (IRQs 5 7 9 10 *11 14 15)
[ 0.725120] ACPI: PCI Interrupt Link [LNK3] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[ 0.725859] ACPI: PCI Interrupt Link [LNK4] (IRQs 5 7 9 10 *11 14 15)
[ 0.726473] ACPI: PCI Interrupt Link [LXV5] (IRQs 5 7 9 *10 11 14 15)
[ 0.727086] ACPI: PCI Interrupt Link [LXV6] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[ 0.727823] ACPI: PCI Interrupt Link [LXV7] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[ 0.728559] ACPI: PCI Interrupt Link [LXV8] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[ 0.729297] ACPI: PCI Interrupt Link [LUBA] (IRQs 5 7 9 10 *11 14 15)
[ 0.729911] ACPI: PCI Interrupt Link [LMC1] (IRQs *5 7 9 10 11 14 15)
[ 0.730507] ACPI: PCI Interrupt Link [LMAC] (IRQs *5 7 9 10 11 14 15)
[ 0.731128] ACPI: PCI Interrupt Link [LAZA] (IRQs 5 7 9 *10 11 14 15)
[ 0.731740] ACPI: PCI Interrupt Link [LSMB] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[ 0.732485] ACPI: PCI Interrupt Link [LUB2] (IRQs 5 7 9 *10 11 14 15)
[ 0.733099] ACPI: PCI Interrupt Link [LIDE] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[ 0.733848] ACPI: PCI Interrupt Link [LSA0] (IRQs 5 7 9 10 *11 14 15)
[ 0.734461] ACPI: PCI Interrupt Link [LSA1] (IRQs 5 7 9 *10 11 14 15)
[ 0.735080] ACPI: PCI Interrupt Link [LSA2] (IRQs 5 7 9 10 *11 14 15)
[ 0.735734] ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0, disabled.
[ 0.736202] ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0
[ 0.736619] ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0, disabled.
[ 0.737085] ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0
[ 0.737503] ACPI: PCI Interrupt Link [AXV5] (IRQs 16) *0
[ 0.737921] ACPI: PCI Interrupt Link [AXV6] (IRQs 16) *0, disabled.
[ 0.738386] ACPI: PCI Interrupt Link [AXV7] (IRQs 16) *0, disabled.
[ 0.738851] ACPI: PCI Interrupt Link [AXV8] (IRQs 16) *0, disabled.
[ 0.739317] ACPI: PCI Interrupt Link [AUBA] (IRQs 22 23) *0
[ 0.739780] ACPI: PCI Interrupt Link [AMA1] (IRQs 22 23) *0
[ 0.740267] ACPI: PCI Interrupt Link [AMAC] (IRQs 22 23) *0
[ 0.740730] ACPI: PCI Interrupt Link [AAZA] (IRQs 22 23) *0
[ 0.741192] ACPI: PCI Interrupt Link [AACI] (IRQs 22 23) *0, disabled.
[ 0.741703] ACPI: PCI Interrupt Link [AMCI] (IRQs 22 23) *0, disabled.
[ 0.742234] ACPI: PCI Interrupt Link [ASMB] (IRQs 22 23) *0, disabled.
[ 0.742745] ACPI: PCI Interrupt Link [AUS2] (IRQs 22 23) *0
[ 0.743208] ACPI: PCI Interrupt Link [AIDE] (IRQs 22 23) *0, disabled.
[ 0.743721] ACPI: PCI Interrupt Link [ASA0] (IRQs 20 21) *0
[ 0.744186] ACPI: PCI Interrupt Link [ASA1] (IRQs 20 21) *0
[ 0.744651] ACPI: PCI Interrupt Link [ASA2] (IRQs 20 21) *0
[ 0.745061] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.745207] vgaarb: device added: PCI:0000:03:00.0,decodes=io+mem,owns=none,locks=none
[ 0.745348] vgaarb: loaded
[ 0.745518] SCSI subsystem initialized
[ 0.745643] libata version 3.00 loaded.
[ 0.745643] usbcore: registered new interface driver usbfs
[ 0.745643] usbcore: registered new interface driver hub
[ 0.745643] usbcore: registered new device driver usb
[ 0.745643] ACPI: WMI: Mapper loaded
[ 0.745643] PCI: Using ACPI for IRQ routing
[ 0.745643] Bluetooth: Core ver 2.15
[ 0.745643] NET: Registered protocol family 31
[ 0.745643] Bluetooth: HCI device and connection manager initialized
[ 0.745643] Bluetooth: HCI socket layer initialized
[ 0.745643] NetLabel: Initializing
[ 0.745643] NetLabel: domain hash size = 128
[ 0.745643] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.745643] NetLabel: unlabeled traffic allowed by default
[ 0.745643] hpet0: at MMIO 0xfeff0000, IRQs 2, 8, 31
[ 0.745643] hpet0: 3 comparators, 32-bit 25.000000 MHz counter
[ 0.760013] Switching to clocksource tsc
[ 0.761556] pnp: PnP ACPI init
[ 0.761665] ACPI: bus type pnp registered
[ 0.764888] pnp: PnP ACPI: found 13 devices
[ 0.764982] ACPI: ACPI bus type pnp unregistered
[ 0.765084] system 00:00: ioport range 0x1000-0x107f has been reserved
[ 0.765189] system 00:00: ioport range 0x1080-0x10ff has been reserved
[ 0.765293] system 00:00: ioport range 0x1400-0x147f has been reserved
[ 0.765397] system 00:00: ioport range 0x1480-0x14ff has been reserved
[ 0.765501] system 00:00: ioport range 0x1800-0x187f has been reserved
[ 0.765605] system 00:00: ioport range 0x1880-0x18ff has been reserved
[ 0.765712] system 00:02: ioport range 0x4d0-0x4d1 has been reserved
[ 0.765815] system 00:02: ioport range 0x295-0x314 has been reserved
[ 0.765918] system 00:02: ioport range 0x880-0x88f has been reserved
[ 0.766028] system 00:0b: iomem range 0xe0000000-0xefffffff has been reserved
[ 0.766139] system 00:0c: iomem range 0xd0000-0xd3fff has been reserved
[ 0.766244] system 00:0c: iomem range 0xd5800-0xd7fff has been reserved
[ 0.766348] system 00:0c: iomem range 0xf0000-0xfbfff could not be reserved
[ 0.766454] system 00:0c: iomem range 0xfc000-0xfffff could not be reserved
[ 0.766569] system 00:0c: iomem range 0x7fef0000-0x7fefffff could not be reserved
[ 0.766709] system 00:0c: iomem range 0xffff0000-0xffffffff has been reserved
[ 0.766816] system 00:0c: iomem range 0x0-0x9ffff could not be reserved
[ 0.766920] system 00:0c: iomem range 0x100000-0x7feeffff could not be reserved
[ 0.767059] system 00:0c: iomem range 0xfec00000-0xfec00fff could not be reserved
[ 0.767199] system 00:0c: iomem range 0xd0000000-0xdfffffff has been reserved
[ 0.767306] system 00:0c: iomem range 0xfee00000-0xfee00fff has been reserved
[ 0.767413] system 00:0c: iomem range 0xfeff0000-0xfeff0000 has been reserved
[ 0.772206] pci 0000:00:03.0: PCI bridge, secondary bus 0000:01
[ 0.772308] pci 0000:00:03.0: IO window: 0x9000-0x9fff
[ 0.772408] pci 0000:00:03.0: MEM window: 0xca000000-0xcdffffff
[ 0.772511] pci 0000:00:03.0: PREFETCH window: 0x000000b0000000-0x000000bfffffff
[ 0.772653] pci 0000:00:0f.0: PCI bridge, secondary bus 0000:02
[ 0.772755] pci 0000:00:0f.0: IO window: 0x8000-0x8fff
[ 0.772855] pci 0000:00:0f.0: MEM window: 0xcfe00000-0xcfefffff
[ 0.772958] pci 0000:00:0f.0: PREFETCH window: disabled
[ 0.773058] pci 0000:00:18.0: PCI bridge, secondary bus 0000:03
[ 0.773160] pci 0000:00:18.0: IO window: 0x7000-0x7fff
[ 0.773260] pci 0000:00:18.0: MEM window: 0xc6000000-0xc9ffffff
[ 0.773363] pci 0000:00:18.0: PREFETCH window: 0x000000a0000000-0x000000afffffff
[ 0.773510] pci 0000:00:03.0: setting latency timer to 64
[ 0.773514] pci 0000:00:0f.0: setting latency timer to 64
[ 0.773521] pci 0000:00:18.0: setting latency timer to 64
[ 0.773524] pci_bus 0000:00: resource 0 io: [0x00-0xffff]
[ 0.773526] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffffffffffff]
[ 0.773528] pci_bus 0000:01: resource 0 io: [0x9000-0x9fff]
[ 0.773530] pci_bus 0000:01: resource 1 mem: [0xca000000-0xcdffffff]
[ 0.773532] pci_bus 0000:01: resource 2 pref mem [0xb0000000-0xbfffffff]
[ 0.773534] pci_bus 0000:02: resource 0 io: [0x8000-0x8fff]
[ 0.773536] pci_bus 0000:02: resource 1 mem: [0xcfe00000-0xcfefffff]
[ 0.773538] pci_bus 0000:02: resource 3 io: [0x00-0xffff]
[ 0.773539] pci_bus 0000:02: resource 4 mem: [0x000000-0xffffffffffffffff]
[ 0.773541] pci_bus 0000:03: resource 0 io: [0x7000-0x7fff]
[ 0.773543] pci_bus 0000:03: resource 1 mem: [0xc6000000-0xc9ffffff]
[ 0.773545] pci_bus 0000:03: resource 2 pref mem [0xa0000000-0xafffffff]
[ 0.773577] NET: Registered protocol family 2
[ 0.773784] IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.774483] TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
[ 0.776238] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.776889] TCP: Hash tables configured (established 262144 bind 65536)
[ 0.776994] TCP reno registered
[ 0.777219] NET: Registered protocol family 1
[ 0.799986] pci 0000:01:00.0: Boot video device
[ 0.800075] Trying to unpack rootfs image as initramfs...
[ 0.955733] Freeing initrd memory: 8333k freed
[ 0.961352] Scanning for low memory corruption every 60 seconds
[ 0.961619] audit: initializing netlink socket (disabled)
[ 0.961734] type=2000 audit(1264042305.957:1): initialized
[ 0.970141] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.971577] VFS: Disk quotas dquot_6.5.2
[ 0.971739] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.972359] fuse init (API version 7.13)
[ 0.972552] msgmni has been set to 4015
[ 0.973073] alg: No test for stdrng (krng)
[ 0.973200] io scheduler noop registered
[ 0.973304] io scheduler anticipatory registered
[ 0.973399] io scheduler deadline registered
[ 0.973520] io scheduler cfq registered (default)
[ 0.973745] alloc irq_desc for 24 on node -1
[ 0.973747] alloc kstat_irqs on node -1
[ 0.973755] pcieport 0000:00:03.0: irq 24 for MSI/MSI-X
[ 0.973760] pcieport 0000:00:03.0: setting latency timer to 64
[ 0.973852] alloc irq_desc for 25 on node -1
[ 0.973854] alloc kstat_irqs on node -1
[ 0.973859] pcieport 0000:00:18.0: irq 25 for MSI/MSI-X
[ 0.973865] pcieport 0000:00:18.0: setting latency timer to 64
[ 0.973927] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.974044] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 0.974276] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
[ 0.974420] ACPI: Power Button [PWRB]
[ 0.974564] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[ 0.974703] ACPI: Power Button [PWRF]
[ 0.975242] processor LNXCPU:00: registered as cooling_device0
[ 0.975390] processor LNXCPU:01: registered as cooling_device1
[ 0.976932] processor LNXCPU:02: registered as cooling_device2
[ 0.977066] processor LNXCPU:03: registered as cooling_device3
[ 0.981001] Linux agpgart interface v0.103
[ 0.981096] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.981296] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.981666] 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.982558] brd: module loaded
[ 0.983002] loop: module loaded
[ 0.983150] input: Macintosh mouse button emulation as /devices/virtual/input/input2
[ 0.983505] sata_nv 0000:00:0e.0: version 3.5
[ 0.983746] ACPI: PCI Interrupt Link [ASA0] enabled at IRQ 21
[ 0.983849] alloc irq_desc for 21 on node -1
[ 0.983851] alloc kstat_irqs on node -1
[ 0.983856] sata_nv 0000:00:0e.0: PCI INT A -> Link[ASA0] -> GSI 21 (level, low) -> IRQ 21
[ 0.984224] sata_nv 0000:00:0e.0: setting latency timer to 64
[ 0.984313] scsi0 : sata_nv
[ 0.984501] scsi1 : sata_nv
[ 0.984722] ata1: SATA max UDMA/133 cmd 0x9f0 ctl 0xbf0 bmdma 0xd800 irq 21
[ 0.984829] ata2: SATA max UDMA/133 cmd 0x970 ctl 0xb70 bmdma 0xd808 irq 21
[ 0.985222] ACPI: PCI Interrupt Link [ASA1] enabled at IRQ 20
[ 0.985323] alloc irq_desc for 20 on node -1
[ 0.985324] alloc kstat_irqs on node -1
[ 0.985328] sata_nv 0000:00:0e.1: PCI INT B -> Link[ASA1] -> GSI 20 (level, low) -> IRQ 20
[ 0.985494] sata_nv 0000:00:0e.1: setting latency timer to 64
[ 0.985573] scsi2 : sata_nv
[ 0.985744] scsi3 : sata_nv
[ 0.985961] ata3: SATA max UDMA/133 cmd 0x9e0 ctl 0xbe0 bmdma 0xc400 irq 20
[ 0.986068] ata4: SATA max UDMA/133 cmd 0x960 ctl 0xb60 bmdma 0xc408 irq 20
[ 0.986496] ACPI: PCI Interrupt Link [ASA2] enabled at IRQ 21
[ 0.986598] sata_nv 0000:00:0e.2: PCI INT C -> Link[ASA2] -> GSI 21 (level, low) -> IRQ 21
[ 0.986765] sata_nv 0000:00:0e.2: setting latency timer to 64
[ 0.986839] scsi4 : sata_nv
[ 0.987024] scsi5 : sata_nv
[ 0.987253] ata5: SATA max UDMA/133 cmd 0xc000 ctl 0xbc00 bmdma 0xb000 irq 21
[ 0.987360] ata6: SATA max UDMA/133 cmd 0xb800 ctl 0xb400 bmdma 0xb008 irq 21
[ 0.987643] pata_amd 0000:00:0d.0: version 0.4.1
[ 0.987672] pata_amd 0000:00:0d.0: setting latency timer to 64
[ 0.987766] scsi6 : pata_amd
[ 0.987952] scsi7 : pata_amd
[ 0.988502] ata7: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xec00 irq 14
[ 0.988608] ata8: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xec08 irq 15
[ 0.988817] ata7: port disabled. ignoring.
[ 0.989369] Fixed MDIO Bus: probed
[ 0.989485] PPP generic driver version 2.4.2
[ 0.989644] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.989985] ACPI: PCI Interrupt Link [AUS2] enabled at IRQ 23
[ 0.990086] alloc irq_desc for 23 on node -1
[ 0.990088] alloc kstat_irqs on node -1
[ 0.990091] ehci_hcd 0000:00:0b.1: PCI INT B -> Link[AUS2] -> GSI 23 (level, low) -> IRQ 23
[ 0.990239] ehci_hcd 0000:00:0b.1: setting latency timer to 64
[ 0.990242] ehci_hcd 0000:00:0b.1: EHCI Host Controller
[ 0.990377] ehci_hcd 0000:00:0b.1: new USB bus registered, assigned bus number 1
[ 0.990561] ehci_hcd 0000:00:0b.1: debug port 1
[ 0.990665] ehci_hcd 0000:00:0b.1: cache line size of 32 is not supported
[ 0.990678] ehci_hcd 0000:00:0b.1: irq 23, io mem 0xcfffe000
[ 1.007680] ehci_hcd 0000:00:0b.1: USB 2.0 started, EHCI 1.00
[ 1.007873] usb usb1: configuration #1 chosen from 1 choice
[ 1.008005] hub 1-0:1.0: USB hub found
[ 1.008101] hub 1-0:1.0: 10 ports detected
[ 1.008244] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.008585] ACPI: PCI Interrupt Link [AUBA] enabled at IRQ 22
[ 1.008686] alloc irq_desc for 22 on node -1
[ 1.008688] alloc kstat_irqs on node -1
[ 1.008691] ohci_hcd 0000:00:0b.0: PCI INT A -> Link[AUBA] -> GSI 22 (level, low) -> IRQ 22
[ 1.008839] ohci_hcd 0000:00:0b.0: setting latency timer to 64
[ 1.008841] ohci_hcd 0000:00:0b.0: OHCI Host Controller
[ 1.008981] ohci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 2
[ 1.009154] ohci_hcd 0000:00:0b.0: irq 22, io mem 0xcffff000
[ 1.072207] usb usb2: configuration #1 chosen from 1 choice
[ 1.072325] hub 2-0:1.0: USB hub found
[ 1.072424] hub 2-0:1.0: 10 ports detected
[ 1.072586] uhci_hcd: USB Universal Host Controller Interface driver
[ 1.072775] PNP: No PS/2 controller found. Probing ports directly.
[ 1.075549] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.075650] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 1.075829] mice: PS/2 mouse device common for all mice
[ 1.075991] Driver 'rtc_cmos' needs updating - please use bus_type methods
[ 1.076130] rtc_cmos 00:05: RTC can wake from S4
[ 1.076250] rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
[ 1.076379] rtc0: alarms up to one year, y3k, 114 bytes nvram, hpet irqs
[ 1.076573] device-mapper: uevent: version 1.0.3
[ 1.076790] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
[ 1.077170] device-mapper: multipath: version 1.1.0 loaded
[ 1.077273] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 1.077809] cpuidle: using governor ladder
[ 1.077922] cpuidle: using governor menu
[ 1.078319] TCP cubic registered
[ 1.078500] NET: Registered protocol family 10
[ 1.078991] lo: Disabled Privacy Extensions
[ 1.079333] NET: Registered protocol family 17
[ 1.079441] Bluetooth: L2CAP ver 2.14
[ 1.079532] Bluetooth: L2CAP socket layer initialized
[ 1.079630] Bluetooth: SCO (Voice Link) ver 0.6
[ 1.079724] Bluetooth: SCO socket layer initialized
[ 1.079885] Bluetooth: RFCOMM TTY layer initialized
[ 1.079996] Bluetooth: RFCOMM socket layer initialized
[ 1.080098] Bluetooth: RFCOMM ver 1.11
[ 1.080285] PM: Resume from disk failed.
[ 1.080303] registered taskstats version 1
[ 1.080790] Magic number: 10:95:865
[ 1.080951] rtc_cmos 00:05: setting system clock to 2010-01-21 02:51:46 UTC (1264042306)
[ 1.081104] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 1.081205] EDD information not available.
[ 1.320595] ata1: SATA link down (SStatus 0 SControl 300)
[ 1.470055] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1.480061] ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1.490161] ata3.00: ATAPI: TSSTcorpCD/DVDW SH-S183L, SB01, max UDMA/33
[ 1.490285] ata3.00: applying bridge limits
[ 1.500374] ata5.00: ATA-8: Hitachi HDS722020ALA330, JKAOA20N, max UDMA/133
[ 1.500485] ata5.00: 3907029168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 1.530186] ata3.00: configured for UDMA/33
[ 1.540393] ata5.00: configured for UDMA/133
[ 1.620037] usb 2-5: new low speed USB device using ohci_hcd and address 2
[ 1.660539] ata2: SATA link down (SStatus 0 SControl 300)
[ 1.661577] scsi 2:0:0:0: CD-ROM TSSTcorp CD/DVDW SH-S183L SB01 PQ: 0 ANSI: 5
[ 1.668827] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[ 1.668971] Uniform CD-ROM driver Revision: 3.20
[ 1.669141] sr 2:0:0:0: Attached scsi CD-ROM sr0
[ 1.669172] sr 2:0:0:0: Attached scsi generic sg0 type 5
[ 1.848284] usb 2-5: configuration #1 chosen from 1 choice
[ 2.150063] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 2.170164] ata4.00: ATAPI: ATAPI iHOS104, WL0B, max UDMA/100
[ 2.210176] ata4.00: configured for UDMA/100
[ 3.060032] usb 2-6: new full speed USB device using ohci_hcd and address 3
[ 3.297381] usb 2-6: configuration #1 chosen from 1 choice
[ 7.210052] ata4.00: qc timeout (cmd 0xa0)
[ 7.210151] ata4.00: TEST_UNIT_READY failed (err_mask=0x5)
[ 7.700063] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 7.760176] ata4.00: configured for UDMA/100
[ 12.760048] ata4.00: qc timeout (cmd 0xa0)
[ 12.760147] ata4.00: TEST_UNIT_READY failed (err_mask=0x5)
[ 12.760251] ata4: limiting SATA link speed to 1.5 Gbps
[ 12.760350] ata4.00: limiting speed to UDMA/100:PIO3
[ 13.250062] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 13.310176] ata4.00: configured for UDMA/100
[ 18.310074] ata4.00: qc timeout (cmd 0xa0)
[ 18.310173] ata4.00: TEST_UNIT_READY failed (err_mask=0x5)
[ 18.310275] ata4.00: disabled
[ 18.310382] ata4: hard resetting link
[ 18.310473] ata4: nv: skipping hardreset on occupied port
[ 18.800062] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 18.800173] ata4: EH complete
[ 18.800386] scsi 4:0:0:0: Direct-Access ATA Hitachi HDS72202 JKAO PQ: 0 ANSI: 5
[ 18.800639] sd 4:0:0:0: Attached scsi generic sg1 type 0
[ 18.800663] sd 4:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
[ 18.800701] sd 4:0:0:0: [sda] Write Protect is off
[ 18.800703] sd 4:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 18.800722] sd 4:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 18.800831] sda: sda1
[ 18.807304] sd 4:0:0:0: [sda] Attached SCSI disk
[ 19.290064] ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 19.347656] ata6.00: ATA-7: ST3320620AS, 3.AAD, max UDMA/133
[ 19.347760] ata6.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 19.430954] ata6.00: configured for UDMA/133
[ 19.431212] scsi 5:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5
[ 19.431476] sd 5:0:0:0: [sdb] 625142448 512-byte logical blocks: (320 GB/298 GiB)
[ 19.431507] sd 5:0:0:0: Attached scsi generic sg2 type 0
[ 19.431619] ata8: port disabled. ignoring.
[ 19.431776] sd 5:0:0:0: [sdb] Write Protect is off
[ 19.431873] sd 5:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 19.431892] sd 5:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 19.432129] sdb: sdb1 sdb2 < sdb5 >
[ 19.491235] sd 5:0:0:0: [sdb] Attached SCSI disk
[ 19.491374] Freeing unused kernel memory: 728k freed
[ 19.491789] Write protecting the kernel read-only data: 7792k
[ 19.603999] forcedeth: Reverse Engineered nForce ethernet driver. Version 0.64.
[ 19.604476] ACPI: PCI Interrupt Link [AMAC] enabled at IRQ 23
[ 19.604582] forcedeth 0000:00:11.0: PCI INT A -> Link[AMAC] -> GSI 23 (level, low) -> IRQ 23
[ 19.604731] forcedeth 0000:00:11.0: setting latency timer to 64
[ 19.604799] nv_probe: set workaround bit for reversed mac addr
[ 19.627102] FDC 0 is a post-1991 82077
[ 19.630104] usbcore: registered new interface driver hiddev
[ 19.632895] ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
[ 19.633001] alloc irq_desc for 19 on node -1
[ 19.633003] alloc kstat_irqs on node -1
[ 19.633010] ohci1394 0000:02:07.0: PCI INT A -> Link[APC4] -> GSI 19 (level, low) -> IRQ 19
[ 19.636785] input: Ideazon Zboard Gaming Keyboard as /devices/pci0000:00/0000:00:0b.0/usb2/2-5/2-5:1.0/input/input3
[ 19.636992] generic-usb 0003:1038:0210.0001: input,hidraw0: USB HID v1.11 Keyboard [Ideazon Zboard Gaming Keyboard] on usb-0000:00:0b.0-5/input0
[ 19.649502] input: Ideazon Zboard Gaming Keyboard as /devices/pci0000:00/0000:00:0b.0/usb2/2-5/2-5:1.1/input/input4
[ 19.649736] generic-usb 0003:1038:0210.0002: input,hiddev96,hidraw1: USB HID v1.11 Device [Ideazon Zboard Gaming Keyboard] on usb-0000:00:0b.0-5/input1
[ 19.657493] input: Razer Razer Copperhead Laser Mouse as /devices/pci0000:00/0000:00:0b.0/usb2/2-6/2-6:1.0/input/input5
[ 19.659125] generic-usb 0003:1532:0101.0003: input,hidraw2: USB HID v1.00 Mouse [Razer Razer Copperhead Laser Mouse] on usb-0000:00:0b.0-6/input0
[ 19.664192] input: Razer Razer Copperhead Laser Mouse as /devices/pci0000:00/0000:00:0b.0/usb2/2-6/2-6:1.1/input/input6
[ 19.664448] generic-usb 0003:1532:0101.0004: input,hidraw3: USB HID v0.01 Keyboard [Razer Razer Copperhead Laser Mouse] on usb-0000:00:0b.0-6/input1
[ 19.664651] usbcore: registered new interface driver usbhid
[ 19.664777] usbhid: v2.6:USB HID core driver
[ 19.690111] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[19] MMIO=[cfeff000-cfeff7ff] Max Packet=[2048] IR/IT contexts=[4/8]
[ 20.130768] forcedeth 0000:00:11.0: ifname eth0, PHY OUI 0x5043 @ 1, addr 00:04:4b:05:cb:6c
[ 20.130915] forcedeth 0000:00:11.0: highdma csum vlan pwrctl mgmt gbit lnktim msi desc-v3
[ 20.131337] ACPI: PCI Interrupt Link [AMA1] enabled at IRQ 22
[ 20.131439] forcedeth 0000:00:12.0: PCI INT A -> Link[AMA1] -> GSI 22 (level, low) -> IRQ 22
[ 20.131584] forcedeth 0000:00:12.0: setting latency timer to 64
[ 20.131622] nv_probe: set workaround bit for reversed mac addr
[ 20.660779] forcedeth 0000:00:12.0: ifname eth1, PHY OUI 0x5043 @ 2, addr 00:04:4b:05:cb:6d
[ 20.660923] forcedeth 0000:00:12.0: highdma csum vlan pwrctl mgmt gbit lnktim msi desc-v3
[ 20.879482] PM: Starting manual resume from disk
[ 20.879584] PM: Resume from partition 8:21
[ 20.879586] PM: Checking hibernation image.
[ 20.879750] PM: Error -22 checking image file
[ 20.879753] PM: Resume from disk failed.
[ 20.946584] EXT4-fs (sdb1): mounted filesystem with ordered data mode
[ 21.005329] ieee1394: Host added: ID:BUS[0-00:1023] GUID[1aa25f0500044b06]
[ 36.196339] udev: starting version 147
[ 36.336001] Adding 6024332k swap on /dev/sdb5. Priority:-1 extents:1 across:6024332k
[ 36.460981] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 36.533040] i2c i2c-0: nForce2 SMBus adapter at 0xf400
[ 36.533061] i2c i2c-1: nForce2 SMBus adapter at 0xf000
[ 36.930438] lp: driver loaded but no devices found
[ 37.116949] nvidia: module license 'NVIDIA' taints kernel.
[ 37.116954] Disabling lock debugging due to kernel taint
[ 37.409723] alloc irq_desc for 26 on node -1
[ 37.409729] alloc kstat_irqs on node -1
[ 37.409738] forcedeth 0000:00:11.0: irq 26 for MSI/MSI-X
[ 37.409931] eth0: no link during initialization.
[ 37.410511] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 37.587107] ACPI: PCI Interrupt Link [AXV5] enabled at IRQ 16
[ 37.587115] alloc irq_desc for 16 on node -1
[ 37.587117] alloc kstat_irqs on node -1
[ 37.587137] nvidia 0000:01:00.0: PCI INT A -> Link[AXV5] -> GSI 16 (level, low) -> IRQ 16
[ 37.587203] nvidia 0000:01:00.0: setting latency timer to 64
[ 37.587598] nvidia 0000:03:00.0: enabling device (0000 -> 0003)
[ 37.587604] nvidia 0000:03:00.0: PCI INT A -> Link[AXV5] -> GSI 16 (level, low) -> IRQ 16
[ 37.587612] nvidia 0000:03:00.0: setting latency timer to 64
[ 37.588016] NVRM: loading NVIDIA UNIX x86_64 Kernel Module 185.18.36 Fri Aug 14 17:35:21 PDT 2009
[ 37.625089] alloc irq_desc for 27 on node -1
[ 37.625092] alloc kstat_irqs on node -1
[ 37.625101] forcedeth 0000:00:12.0: irq 27 for MSI/MSI-X
[ 37.940509] ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17
[ 37.940514] alloc irq_desc for 17 on node -1
[ 37.940516] alloc kstat_irqs on node -1
[ 37.940522] CA0106 0000:02:09.0: PCI INT A -> Link[APC2] -> GSI 17 (level, low) -> IRQ 17
[ 37.940546] snd-ca0106: Model 1011 Rev 00000000 Serial 10111102
[ 37.966520] ACPI: PCI Interrupt Link [AAZA] enabled at IRQ 23
[ 37.966525] HDA Intel 0000:00:0f.1: PCI INT B -> Link[AAZA] -> GSI 23 (level, low) -> IRQ 23
[ 37.966557] HDA Intel 0000:00:0f.1: setting latency timer to 64
[ 39.494379] hda_codec: ALC889A: BIOS auto-probing.
[ 40.090350] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:0f.1/input/input7
[ 40.803847] RPC: Registered udp transport module.
[ 40.803850] RPC: Registered tcp transport module.
[ 40.803851] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 40.957334] Bridge firewalling registered
[ 40.959871] device eth0 entered promiscuous mode
[ 43.429960] vboxdrv: Trying to deactivate the NMI watchdog permanently...
[ 43.429964] vboxdrv: Warning: 2.6.31+ kernel detected. Most likely the hwardware performance
[ 43.429965] vboxdrv: counter framework which can generate NMIs is active. You have to prevent
[ 43.429966] vboxdrv: the usage of hardware performance counters by
[ 43.429967] vboxdrv: echo 2 > /proc/sys/kernel/perf_counter_paranoid
[ 43.429971] vboxdrv: Found 4 processor cores.
[ 43.430667] VBoxDrv: dbg - g_abExecMemory=ffffffffa0d71460
[ 43.430723] vboxdrv: fAsync=0 offMin=0x4f6 offMax=0x2e04
[ 43.431169] vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
[ 43.431171] vboxdrv: Successfully loaded version 3.0.12 (interface 0x00110000).
[ 43.635875] VBoxNetFlt: dbg - g_abExecMemory=ffffffffa0b1a260
[ 43.638013] VBoxNetAdp: dbg - g_abExecMemory=ffffffffa0f0db00
[ 43.709833] virbr0: starting userspace STP failed, starting kernel STP
[ 43.768351] ppdev: user-space parallel port driver
[ 43.788938] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 43.789339] CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
[ 43.789341] nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
[ 43.789342] sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
[ 47.474245] lo: Disabled Privacy Extensions
[ 48.370049] eth1: no IPv6 routers present
[ 51.033227] svc: failed to register lockdv1 RPC service (errno 97).
[ 51.311276] br0: no IPv6 routers present
^ permalink raw reply [flat|nested] 28+ messages in thread
* Re: sata_nv times out for BD-ROM iHOS104-08
@ 2010-01-17 4:54 Gregory Moyer
0 siblings, 0 replies; 28+ messages in thread
From: Gregory Moyer @ 2010-01-17 4:54 UTC (permalink / raw)
To: linux-kernel
> I contacted LiteON technical support in the meantime, but they are no
>
> help. They said they tested with one Linux system and it worked.
>
> I will probably buy one of the above VIA cards and use it for this drive.
>
> Thanks for helping!
I too am having the same problem with the iHOS104. I filed a bug
report against Ubuntu Karmic
(https://bugs.launchpad.net/ubuntu/+source/linux/+bug/344093). At
least one other person reporting on that same bug report has confirmed
the issue. We are both seeing the problem with nVidia chipsets using
the sata_nv driver. There is a lot of information in the report, so
I'll skip re-posting it all here. However, as the previous poster
mentioned, after contacting LiteOn support, I was told the drive works
in Mandriva 2007.0. I tried it and sure enough, it does. The other
poster in the linked report confirmed this as well, stating that for
that distribution, the kernel was at 2.6.17 and the sata_nv driver was
at 0.8. I have tried several distributions/kernels, including 2.6.32.
I have also tried a myriad of kernel and BIOS options, including all
of the ones mentioned so far in this thread. If I can help in any way
to get this resolved, please let me know. Thanks for taking the time
to look into it.
^ permalink raw reply [flat|nested] 28+ messages in thread
end of thread, other threads:[~2010-06-03 17:40 UTC | newest]
Thread overview: 28+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2009-12-22 16:07 sata_nv times out for BD-ROM iHOS104-08 Cengiz Gunay
2009-12-23 7:38 ` Tejun Heo
[not found] ` <d2d378040912232302u4b550dap687fcadced237935@mail.gmail.com>
2009-12-24 7:25 ` Tejun Heo
2010-01-16 21:34 ` Cengiz Günay
2010-01-17 15:28 ` Ozan Çağlayan
2010-01-19 9:05 ` Tejun Heo
2010-01-19 9:34 ` Ozan Çağlayan
2010-01-20 2:13 ` Tejun Heo
2010-01-20 2:59 ` Robert Hancock
2010-01-22 14:11 ` Cengiz Günay
2010-01-23 3:45 ` Tejun Heo
2010-01-23 21:39 ` Cengiz Günay
[not found] ` <4B67A149.10406@kernel.org>
2010-02-17 16:14 ` Cengiz Günay
2010-02-18 1:50 ` Tejun Heo
2010-02-20 19:11 ` Cengiz Günay
2010-02-21 1:01 ` Tejun Heo
2010-02-21 21:28 ` Cengiz Günay
2010-02-23 2:38 ` Tejun Heo
2010-02-28 17:24 ` Cengiz Günay
2010-03-02 11:48 ` Tejun Heo
2010-03-08 19:17 ` Cengiz Günay
2010-03-08 23:46 ` Robert Hancock
2010-03-09 1:21 ` Tejun Heo
2010-03-09 5:18 ` Cengiz Günay
2010-05-25 19:34 ` Tejun Heo
2010-01-17 4:54 Gregory Moyer
2010-01-21 3:15 Gregory Moyer
2010-06-03 17:40 Gregory Moyer
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).