[PATCH 3.14 00/34] 3.14.27-stable review

[PATCH 3.14 00/34] 3.14.27-stable review

[Greg Kroah-Hartman]

This is the start of the stable review cycle for the 3.14.27 release.
There are 34 patches in this series, all will be posted as a response
to this one.  If anyone has any issues with these being applied, please
let me know.

Responses should be made by Tue Dec 16 20:17:55 UTC 2014.
Anything received after that time might be too late.

The whole patch series can be found in one patch at:
	kernel.org/pub/linux/kernel/v3.0/stable-review/patch-3.14.27-rc1.gz
and the diffstat can be found below.

thanks,

greg k-h

-------------
Pseudo-Shortlog of commits:

Greg Kroah-Hartman <gregkh@linuxfoundation.org>
    Linux 3.14.27-rc1

Takashi Iwai <tiwai@suse.de>
    ALSA: usb-audio: Don't resubmit pending URBs at MIDI error recovery

Takashi Iwai <tiwai@suse.de>
    ALSA: hda - Fix built-in mic at resume on Lenovo Ideapad S210

Takashi Iwai <tiwai@suse.de>
    ALSA: hda - Add EAPD fixup for ASUS Z99He laptop

Ronald Wahl <ronald.wahl@raritan.com>
    mac80211: Fix regression that triggers a kernel BUG with CCMP

Anton Blanchard <anton@samba.org>
    powerpc: 32 bit getcpu VDSO function uses 64 bit instructions

Todd Fujinaka <todd.fujinaka@intel.com>
    igb: bring link up when PHY is powered up

Kan Liang <kan.liang@intel.com>
    perf/x86/intel: Protect LBR and extra_regs against KVM lying

Daniel Borkmann <dborkman@redhat.com>
    net: sctp: use MAX_HEADER for headroom reserve in output path

Eric Dumazet <edumazet@google.com>
    net: mvneta: fix race condition in mvneta_tx()

willy tarreau <w@1wt.eu>
    net: mvneta: fix Tx interrupt delay

Tom Herbert <therbert@google.com>
    gre: Set inner mac header in gro complete

Nicolas Dichtel <nicolas.dichtel@6wind.com>
    rtnetlink: release net refcnt on error in do_setlink()

Jack Morgenstein <jackm@dev.mellanox.co.il>
    net/mlx4_core: Limit count field to 24 bits in qp_alloc_res

Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
    tg3: fix ring init when there are more TX than RX channels

Marcelo Leitner <mleitner@redhat.com>
    Fix race condition between vxlan_sock_add and vxlan_sock_release

Yuri Chislov <yuri.chislov@gmail.com>
    ipv6: gre: fix wrong skb->protocol in WCCP

lucien <lucien.xin@gmail.com>
    ip_tunnel: the lack of vti_link_ops' dellink() cause kernel panic

Dmitry Torokhov <dtor@chromium.org>
    sata_fsl: fix error handling of irq_of_parse_and_map

Tejun Heo <tj@kernel.org>
    ahci: disable MSI on SAMSUNG 0xa800 SSD

Devin Ryles <devin.ryles@intel.com>
    AHCI: Add DeviceIDs for Sunrise Point-LP SATA controller

Mathias Nyman <mathias.nyman@linux.intel.com>
    USB: xhci: Reset a halted endpoint immediately when we encounter a stall.

Sakari Ailus <sakari.ailus@iki.fi>
    media: smiapp: Only some selection targets are settable

Chris Clayton <chris2553@googlemail.com>
    x86: Use $(OBJDUMP) instead of plain objdump

Daniel Vetter <daniel.vetter@ffwll.ch>
    drm/i915: Unlock panel even when LVDS is disabled

Daniel Vetter <daniel.vetter@ffwll.ch>
    drm/i915: More cautious with pch fifo underruns

Petr Mladek <pmladek@suse.cz>
    drm/radeon: kernel panic in drm_calc_vbltimestamp_from_scanoutpos with 3.18.0-rc6

Grygorii Strashko <grygorii.strashko@ti.com>
    i2c: davinci: generate STP always when NACK is received

Alexander Kochetkov <al.kochet@gmail.com>
    i2c: omap: fix i207 errata handling

Alexander Kochetkov <al.kochet@gmail.com>
    i2c: omap: fix NACK and Arbitration Lost irq handling

Seth Forshee <seth.forshee@canonical.com>
    xen-netfront: Remove BUGs on paged skb data which crosses a page boundary

Daniel Forrest <dan.forrest@ssec.wisc.edu>
    mm: fix anon_vma_clone() error treatment

Hugh Dickins <hughd@google.com>
    mm: fix swapoff hang after page migration and fork

Andrew Morton <akpm@linux-foundation.org>
    mm/vmpressure.c: fix race in vmpressure_work_fn()

Weijie Yang <weijie.yang@samsung.com>
    mm: frontswap: invalidate expired data on a dup-store failure


-------------

Diffstat:

 Makefile                                           |  4 +-
 arch/powerpc/kernel/vdso32/getcpu.S                |  4 +-
 arch/x86/boot/compressed/Makefile                  |  2 +-
 arch/x86/kernel/cpu/perf_event.c                   |  3 +
 arch/x86/kernel/cpu/perf_event.h                   | 12 ++--
 arch/x86/kernel/cpu/perf_event_intel.c             | 66 +++++++++++++++++++++-
 drivers/ata/ahci.c                                 |  4 ++
 drivers/ata/sata_fsl.c                             |  2 +-
 drivers/gpu/drm/i915/intel_display.c               |  2 -
 drivers/gpu/drm/i915/intel_lvds.c                  | 22 ++++----
 drivers/gpu/drm/radeon/radeon_kms.c                |  2 +
 drivers/i2c/busses/i2c-davinci.c                   |  8 +--
 drivers/i2c/busses/i2c-omap.c                      | 10 ++--
 drivers/media/i2c/smiapp/smiapp-core.c             |  2 +-
 drivers/net/ethernet/broadcom/tg3.c                |  3 +-
 drivers/net/ethernet/intel/igb/igb_main.c          |  2 +
 drivers/net/ethernet/marvell/mvneta.c              |  5 +-
 .../net/ethernet/mellanox/mlx4/resource_tracker.c  |  2 +-
 drivers/net/vxlan.c                                | 10 +---
 drivers/net/xen-netfront.c                         |  5 --
 drivers/usb/host/xhci-ring.c                       | 40 ++++---------
 drivers/usb/host/xhci.c                            | 60 +++++---------------
 mm/frontswap.c                                     |  4 +-
 mm/memory.c                                        | 26 ++++-----
 mm/mmap.c                                          | 10 +++-
 mm/rmap.c                                          |  6 +-
 mm/vmpressure.c                                    |  8 ++-
 net/core/rtnetlink.c                               |  1 +
 net/ipv4/gre_offload.c                             |  3 +
 net/ipv4/ip_vti.c                                  |  1 +
 net/ipv6/ip6_gre.c                                 |  4 +-
 net/ipv6/ip6_vti.c                                 | 11 ++++
 net/mac80211/aes_ccm.c                             |  3 +
 net/sctp/output.c                                  |  4 +-
 sound/pci/hda/patch_analog.c                       |  1 +
 sound/pci/hda/patch_realtek.c                      |  1 +
 sound/usb/midi.c                                   |  2 +
 37 files changed, 202 insertions(+), 153 deletions(-)

[PATCH 3.14 01/34] mm: frontswap: invalidate expired data on a dup-store failure

[Greg Kroah-Hartman]

3.14-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Weijie Yang <weijie.yang@samsung.com>

commit fb993fa1a2f669215fa03a09eed7848f2663e336 upstream.

If a frontswap dup-store failed, it should invalidate the expired page
in the backend, or it could trigger some data corruption issue.
Such as:
 1. use zswap as the frontswap backend with writeback feature
 2. store a swap page(version_1) to entry A, success
 3. dup-store a newer page(version_2) to the same entry A, fail
 4. use __swap_writepage() write version_2 page to swapfile, success
 5. zswap do shrink, writeback version_1 page to swapfile
 6. version_2 page is overwrited by version_1, data corrupt.

This patch fixes this issue by invalidating expired data immediately
when meet a dup-store failure.

Signed-off-by: Weijie Yang <weijie.yang@samsung.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Seth Jennings <sjennings@variantweb.net>
Cc: Dan Streetman <ddstreet@ieee.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Bob Liu <bob.liu@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 mm/frontswap.c |    4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

--- a/mm/frontswap.c
+++ b/mm/frontswap.c
@@ -244,8 +244,10 @@ int __frontswap_store(struct page *page)
 		  the (older) page from frontswap
 		 */
 		inc_frontswap_failed_stores();
-		if (dup)
+		if (dup) {
 			__frontswap_clear(sis, offset);
+			frontswap_ops->invalidate_page(type, offset);
+		}
 	}
 	if (frontswap_writethrough_enabled)
 		/* report failure so swap also writes to swap device */

[PATCH 3.14 02/34] mm/vmpressure.c: fix race in vmpressure_work_fn()

[Greg Kroah-Hartman]

3.14-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Andrew Morton <akpm@linux-foundation.org>

commit 91b57191cfd152c02ded0745250167d0263084f8 upstream.

In some android devices, there will be a "divide by zero" exception.
vmpr->scanned could be zero before spin_lock(&vmpr->sr_lock).

Addresses https://bugzilla.kernel.org/show_bug.cgi?id=88051

[akpm@linux-foundation.org: neaten]
Reported-by: ji_ang <ji_ang@163.com>
Cc: Anton Vorontsov <anton.vorontsov@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 mm/vmpressure.c |    8 +++++---
 1 file changed, 5 insertions(+), 3 deletions(-)

--- a/mm/vmpressure.c
+++ b/mm/vmpressure.c
@@ -165,6 +165,7 @@ static void vmpressure_work_fn(struct wo
 	unsigned long scanned;
 	unsigned long reclaimed;
 
+	spin_lock(&vmpr->sr_lock);
 	/*
 	 * Several contexts might be calling vmpressure(), so it is
 	 * possible that the work was rescheduled again before the old
@@ -173,11 +174,12 @@ static void vmpressure_work_fn(struct wo
 	 * here. No need for any locks here since we don't care if
 	 * vmpr->reclaimed is in sync.
 	 */
-	if (!vmpr->scanned)
+	scanned = vmpr->scanned;
+	if (!scanned) {
+		spin_unlock(&vmpr->sr_lock);
 		return;
+	}
 
-	spin_lock(&vmpr->sr_lock);
-	scanned = vmpr->scanned;
 	reclaimed = vmpr->reclaimed;
 	vmpr->scanned = 0;
 	vmpr->reclaimed = 0;

[PATCH 3.14 03/34] mm: fix swapoff hang after page migration and fork

[Greg Kroah-Hartman]

3.14-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Hugh Dickins <hughd@google.com>

commit 2022b4d18a491a578218ce7a4eca8666db895a73 upstream.

I've been seeing swapoff hangs in recent testing: it's cycling around
trying unsuccessfully to find an mm for some remaining pages of swap.

I have been exercising swap and page migration more heavily recently,
and now notice a long-standing error in copy_one_pte(): it's trying to
add dst_mm to swapoff's mmlist when it finds a swap entry, but is doing
so even when it's a migration entry or an hwpoison entry.

Which wouldn't matter much, except it adds dst_mm next to src_mm,
assuming src_mm is already on the mmlist: which may not be so.  Then if
pages are later swapped out from dst_mm, swapoff won't be able to find
where to replace them.

There's already a !non_swap_entry() test for stats: move that up before
the swap_duplicate() and the addition to mmlist.

Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Kelley Nielsen <kelleynnn@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 mm/memory.c |   24 ++++++++++++------------
 1 file changed, 12 insertions(+), 12 deletions(-)

--- a/mm/memory.c
+++ b/mm/memory.c
@@ -808,20 +808,20 @@ copy_one_pte(struct mm_struct *dst_mm, s
 		if (!pte_file(pte)) {
 			swp_entry_t entry = pte_to_swp_entry(pte);
 
-			if (swap_duplicate(entry) < 0)
-				return entry.val;
+			if (likely(!non_swap_entry(entry))) {
+				if (swap_duplicate(entry) < 0)
+					return entry.val;
 
-			/* make sure dst_mm is on swapoff's mmlist. */
-			if (unlikely(list_empty(&dst_mm->mmlist))) {
-				spin_lock(&mmlist_lock);
-				if (list_empty(&dst_mm->mmlist))
-					list_add(&dst_mm->mmlist,
-						 &src_mm->mmlist);
-				spin_unlock(&mmlist_lock);
-			}
-			if (likely(!non_swap_entry(entry)))
+				/* make sure dst_mm is on swapoff's mmlist. */
+				if (unlikely(list_empty(&dst_mm->mmlist))) {
+					spin_lock(&mmlist_lock);
+					if (list_empty(&dst_mm->mmlist))
+						list_add(&dst_mm->mmlist,
+							 &src_mm->mmlist);
+					spin_unlock(&mmlist_lock);
+				}
 				rss[MM_SWAPENTS]++;
-			else if (is_migration_entry(entry)) {
+			} else if (is_migration_entry(entry)) {
 				page = migration_entry_to_page(entry);
 
 				if (PageAnon(page))

[PATCH 3.14 04/34] mm: fix anon_vma_clone() error treatment

[Greg Kroah-Hartman]

3.14-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Daniel Forrest <dan.forrest@ssec.wisc.edu>

commit c4ea95d7cd08d9ffd7fa75e6c5e0332d596dd11e upstream.

Andrew Morton noticed that the error return from anon_vma_clone() was
being dropped and replaced with -ENOMEM (which is not itself a bug
because the only error return value from anon_vma_clone() is -ENOMEM).

I did an audit of callers of anon_vma_clone() and discovered an actual
bug where the error return was being lost.  In __split_vma(), between
Linux 3.11 and 3.12 the code was changed so the err variable is used
before the call to anon_vma_clone() and the default initial value of
-ENOMEM is overwritten.  So a failure of anon_vma_clone() will return
success since err at this point is now zero.

Below is a patch which fixes this bug and also propagates the error
return value from anon_vma_clone() in all cases.

Fixes: ef0855d334e1 ("mm: mempolicy: turn vma_set_policy() into vma_dup_policy()")
Signed-off-by: Daniel Forrest <dan.forrest@ssec.wisc.edu>
Reviewed-by: Michal Hocko <mhocko@suse.cz>
Cc: Konstantin Khlebnikov <koct9i@gmail.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Tim Hartrick <tim@edgecast.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Michel Lespinasse <walken@google.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 mm/mmap.c |   10 +++++++---
 mm/rmap.c |    6 ++++--
 2 files changed, 11 insertions(+), 5 deletions(-)

--- a/mm/mmap.c
+++ b/mm/mmap.c
@@ -745,8 +745,11 @@ again:			remove_next = 1 + (end > next->
 		 * shrinking vma had, to cover any anon pages imported.
 		 */
 		if (exporter && exporter->anon_vma && !importer->anon_vma) {
-			if (anon_vma_clone(importer, exporter))
-				return -ENOMEM;
+			int error;
+
+			error = anon_vma_clone(importer, exporter);
+			if (error)
+				return error;
 			importer->anon_vma = exporter->anon_vma;
 		}
 	}
@@ -2428,7 +2431,8 @@ static int __split_vma(struct mm_struct
 	if (err)
 		goto out_free_vma;
 
-	if (anon_vma_clone(new, vma))
+	err = anon_vma_clone(new, vma);
+	if (err)
 		goto out_free_mpol;
 
 	if (new->vm_file)
--- a/mm/rmap.c
+++ b/mm/rmap.c
@@ -274,6 +274,7 @@ int anon_vma_fork(struct vm_area_struct
 {
 	struct anon_vma_chain *avc;
 	struct anon_vma *anon_vma;
+	int error;
 
 	/* Don't bother if the parent process has no anon_vma here. */
 	if (!pvma->anon_vma)
@@ -283,8 +284,9 @@ int anon_vma_fork(struct vm_area_struct
 	 * First, attach the new VMA to the parent VMA's anon_vmas,
 	 * so rmap can find non-COWed pages in child processes.
 	 */
-	if (anon_vma_clone(vma, pvma))
-		return -ENOMEM;
+	error = anon_vma_clone(vma, pvma);
+	if (error)
+		return error;
 
 	/* Then add our own anon_vma. */
 	anon_vma = anon_vma_alloc();

[PATCH 3.14 05/34] xen-netfront: Remove BUGs on paged skb data which crosses a page boundary

[Greg Kroah-Hartman]

3.14-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Seth Forshee <seth.forshee@canonical.com>

commit 8d609725d4357f499e2103e46011308b32f53513 upstream.

These BUGs can be erroneously triggered by frags which refer to
tail pages within a compound page. The data in these pages may
overrun the hardware page while still being contained within the
compound page, but since compound_order() evaluates to 0 for tail
pages the assertion fails. The code already iterates through
subsequent pages correctly in this scenario, so the BUGs are
unnecessary and can be removed.

Fixes: f36c374782e4 ("xen/netfront: handle compound page fragments on transmit")
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/net/xen-netfront.c |    5 -----
 1 file changed, 5 deletions(-)

--- a/drivers/net/xen-netfront.c
+++ b/drivers/net/xen-netfront.c
@@ -469,9 +469,6 @@ static void xennet_make_frags(struct sk_
 		len = skb_frag_size(frag);
 		offset = frag->page_offset;
 
-		/* Data must not cross a page boundary. */
-		BUG_ON(len + offset > PAGE_SIZE<<compound_order(page));
-
 		/* Skip unused frames from start of page */
 		page += offset >> PAGE_SHIFT;
 		offset &= ~PAGE_MASK;
@@ -479,8 +476,6 @@ static void xennet_make_frags(struct sk_
 		while (len > 0) {
 			unsigned long bytes;
 
-			BUG_ON(offset >= PAGE_SIZE);
-
 			bytes = PAGE_SIZE - offset;
 			if (bytes > len)
 				bytes = len;

[PATCH 3.14 06/34] i2c: omap: fix NACK and Arbitration Lost irq handling

[Greg Kroah-Hartman]

3.14-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Alexander Kochetkov <al.kochet@gmail.com>

commit 27caca9d2e01c92b26d0690f065aad093fea01c7 upstream.

commit 1d7afc95946487945cc7f5019b41255b72224b70 (i2c: omap: ack IRQ in parts)
changed the interrupt handler to complete transfers without clearing
XRDY (AL case) and ARDY (NACK case) flags. XRDY or ARDY interrupts will be
fired again. As a result, ISR keep processing transfer after it was already
complete (from the driver code point of view).

A didn't see real impacts of the 1d7afc9, but it is really bad idea to
have ISR running on user data after transfer was complete.

It looks, what 1d7afc9 violate TI specs in what how AL and NACK should be
handled (see Note 1, sprugn4r, Figure 17-31 and Figure 17-32).

According to specs (if I understood correctly), in case of NACK and AL driver
must reset NACK, AL, ARDY, RDR, and RRDY (Master Receive Mode), and
NACK, AL, ARDY, and XDR (Master Transmitter Mode).

All that is done down the code under the if condition:
if (stat & (OMAP_I2C_STAT_ARDY | OMAP_I2C_STAT_NACK | OMAP_I2C_STAT_AL)) ...

The patch restore pre 1d7afc9 logic of handling NACK and AL interrupts, so
no interrupts is fired after ISR informs the rest of driver what transfer
complete.

Note: instead of removing break under NACK case, we could just replace 'break'
with 'continue' and allow NACK transfer to finish using ARDY event. I found
that NACK and ARDY bits usually set together. That case confirm TI wiki:
http://processors.wiki.ti.com/index.php/I2C_Tips#Detecting_and_handling_NACK

In order if someone interested in the event traces for NACK and AL cases,
I sent them to mailing list.

Tested on Beagleboard XM C.

Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Fixes: 1d7afc9 i2c: omap: ack IRQ in parts
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/i2c/busses/i2c-omap.c |    2 --
 1 file changed, 2 deletions(-)

--- a/drivers/i2c/busses/i2c-omap.c
+++ b/drivers/i2c/busses/i2c-omap.c
@@ -926,14 +926,12 @@ omap_i2c_isr_thread(int this_irq, void *
 		if (stat & OMAP_I2C_STAT_NACK) {
 			err |= OMAP_I2C_STAT_NACK;
 			omap_i2c_ack_stat(dev, OMAP_I2C_STAT_NACK);
-			break;
 		}
 
 		if (stat & OMAP_I2C_STAT_AL) {
 			dev_err(dev->dev, "Arbitration lost\n");
 			err |= OMAP_I2C_STAT_AL;
 			omap_i2c_ack_stat(dev, OMAP_I2C_STAT_AL);
-			break;
 		}
 
 		/*

[PATCH 3.14 07/34] i2c: omap: fix i207 errata handling

[Greg Kroah-Hartman]

3.14-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Alexander Kochetkov <al.kochet@gmail.com>

commit ccfc866356674cb3a61829d239c685af6e85f197 upstream.

commit 6d9939f651419a63e091105663821f9c7d3fec37 (i2c: omap: split out [XR]DR
and [XR]RDY) changed the way how errata i207 (I2C: RDR Flag May Be Incorrectly
Set) get handled. 6d9939f6514 code doesn't correspond to workaround provided by
errata.

According to errata ISR must filter out spurious RDR before data read not after.
ISR must read RXSTAT to get number of bytes available to read. Because RDR
could be set while there could no data in the receive FIFO.

Restored pre 6d9939f6514 way of handling errata.

Found by code review. Real impact haven't seen.
Tested on Beagleboard XM C.

Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Fixes: 6d9939f651419a63e09110 i2c: omap: split out [XR]DR and [XR]RDY
Tested-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/i2c/busses/i2c-omap.c |    8 +++++---
 1 file changed, 5 insertions(+), 3 deletions(-)

--- a/drivers/i2c/busses/i2c-omap.c
+++ b/drivers/i2c/busses/i2c-omap.c
@@ -956,11 +956,13 @@ omap_i2c_isr_thread(int this_irq, void *
 			if (dev->fifo_size)
 				num_bytes = dev->buf_len;
 
-			omap_i2c_receive_data(dev, num_bytes, true);
-
-			if (dev->errata & I2C_OMAP_ERRATA_I207)
+			if (dev->errata & I2C_OMAP_ERRATA_I207) {
 				i2c_omap_errata_i207(dev, stat);
+				num_bytes = (omap_i2c_read_reg(dev,
+					OMAP_I2C_BUFSTAT_REG) >> 8) & 0x3F;
+			}
 
+			omap_i2c_receive_data(dev, num_bytes, true);
 			omap_i2c_ack_stat(dev, OMAP_I2C_STAT_RDR);
 			continue;
 		}

[PATCH 3.14 09/34] drm/radeon: kernel panic in drm_calc_vbltimestamp_from_scanoutpos with 3.18.0-rc6

[Greg Kroah-Hartman]

3.14-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Petr Mladek <pmladek@suse.cz>

commit f5475cc43c899e33098d4db44b7c5e710f16589d upstream.

I was unable too boot 3.18.0-rc6 because of the following kernel
panic in drm_calc_vbltimestamp_from_scanoutpos():

    [drm] Initialized drm 1.1.0 20060810
    [drm] radeon kernel modesetting enabled.
    [drm] initializing kernel modesetting (RV100 0x1002:0x515E 0x15D9:0x8080).
    [drm] register mmio base: 0xC8400000
    [drm] register mmio size: 65536
    radeon 0000:0b:01.0: VRAM: 128M 0x00000000D0000000 - 0x00000000D7FFFFFF (16M used)
    radeon 0000:0b:01.0: GTT: 512M 0x00000000B0000000 - 0x00000000CFFFFFFF
    [drm] Detected VRAM RAM=128M, BAR=128M
    [drm] RAM width 16bits DDR
    [TTM] Zone  kernel: Available graphics memory: 3829346 kiB
    [TTM] Zone   dma32: Available graphics memory: 2097152 kiB
    [TTM] Initializing pool allocator
    [TTM] Initializing DMA pool allocator
    [drm] radeon: 16M of VRAM memory ready
    [drm] radeon: 512M of GTT memory ready.
    [drm] GART: num cpu pages 131072, num gpu pages 131072
    [drm] PCI GART of 512M enabled (table at 0x0000000037880000).
    radeon 0000:0b:01.0: WB disabled
    radeon 0000:0b:01.0: fence driver on ring 0 use gpu addr 0x00000000b0000000 and cpu addr 0xffff8800bbbfa000
    [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
    [drm] Driver supports precise vblank timestamp query.
    [drm] radeon: irq initialized.
    [drm] Loading R100 Microcode
    radeon 0000:0b:01.0: Direct firmware load for radeon/R100_cp.bin failed with error -2
    radeon_cp: Failed to load firmware "radeon/R100_cp.bin"
    [drm:r100_cp_init] *ERROR* Failed to load firmware!
    radeon 0000:0b:01.0: failed initializing CP (-2).
    radeon 0000:0b:01.0: Disabling GPU acceleration
    [drm] radeon: cp finalized
    BUG: unable to handle kernel NULL pointer dereference at 000000000000025c
    IP: [<ffffffff8150423b>] drm_calc_vbltimestamp_from_scanoutpos+0x4b/0x320
    PGD 0
    Oops: 0000 [#1] SMP
    Modules linked in:
    CPU: 1 PID: 1 Comm: swapper/0 Not tainted 3.18.0-rc6-4-default #2649
    Hardware name: Supermicro X7DB8/X7DB8, BIOS 6.00 07/26/2006
    task: ffff880234da2010 ti: ffff880234da4000 task.ti: ffff880234da4000
    RIP: 0010:[<ffffffff8150423b>]  [<ffffffff8150423b>] drm_calc_vbltimestamp_from_scanoutpos+0x4b/0x320
    RSP: 0000:ffff880234da7918  EFLAGS: 00010086
    RAX: ffffffff81557890 RBX: 0000000000000000 RCX: ffff880234da7a48
    RDX: ffff880234da79f4 RSI: 0000000000000000 RDI: ffff880232e15000
    RBP: ffff880234da79b8 R08: 0000000000000000 R09: 0000000000000000
    R10: 000000000000000a R11: 0000000000000001 R12: ffff880232dda1c0
    R13: ffff880232e1518c R14: 0000000000000292 R15: ffff880232e15000
    FS:  0000000000000000(0000) GS:ffff88023fc40000(0000) knlGS:0000000000000000
    CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
    CR2: 000000000000025c CR3: 0000000002014000 CR4: 00000000000007e0
    Stack:
     ffff880234da79d8 0000000000000286 ffff880232dcbc00 0000000000002480
     ffff880234da7958 0000000000000296 ffff880234da7998 ffffffff8151b51d
     ffff880234da7a48 0000000032dcbeb0 ffff880232dcbc00 ffff880232dcbc58
    Call Trace:
     [<ffffffff8151b51d>] ? drm_vma_offset_remove+0x1d/0x110
     [<ffffffff8152dc98>] radeon_get_vblank_timestamp_kms+0x38/0x60
     [<ffffffff8152076a>] ? ttm_bo_release_list+0xba/0x180
     [<ffffffff81503751>] drm_get_last_vbltimestamp+0x41/0x70
     [<ffffffff81503933>] vblank_disable_and_save+0x73/0x1d0
     [<ffffffff81106b2f>] ? try_to_del_timer_sync+0x4f/0x70
     [<ffffffff81505245>] drm_vblank_cleanup+0x65/0xa0
     [<ffffffff815604fa>] radeon_irq_kms_fini+0x1a/0x70
     [<ffffffff8156c07e>] r100_init+0x26e/0x410
     [<ffffffff8152ae3e>] radeon_device_init+0x7ae/0xb50
     [<ffffffff8152d57f>] radeon_driver_load_kms+0x8f/0x210
     [<ffffffff81506965>] drm_dev_register+0xb5/0x110
     [<ffffffff8150998f>] drm_get_pci_dev+0x8f/0x200
     [<ffffffff815291cd>] radeon_pci_probe+0xad/0xe0
     [<ffffffff8141a365>] local_pci_probe+0x45/0xa0
     [<ffffffff8141b741>] pci_device_probe+0xd1/0x130
     [<ffffffff81633dad>] driver_probe_device+0x12d/0x3e0
     [<ffffffff8163413b>] __driver_attach+0x9b/0xa0
     [<ffffffff816340a0>] ? __device_attach+0x40/0x40
     [<ffffffff81631cd3>] bus_for_each_dev+0x63/0xa0
     [<ffffffff8163378e>] driver_attach+0x1e/0x20
     [<ffffffff81633390>] bus_add_driver+0x180/0x240
     [<ffffffff81634914>] driver_register+0x64/0xf0
     [<ffffffff81419cac>] __pci_register_driver+0x4c/0x50
     [<ffffffff81509bf5>] drm_pci_init+0xf5/0x120
     [<ffffffff821dc871>] ? ttm_init+0x6a/0x6a
     [<ffffffff821dc908>] radeon_init+0x97/0xb5
     [<ffffffff810002fc>] do_one_initcall+0xbc/0x1f0
     [<ffffffff810e3278>] ? __wake_up+0x48/0x60
     [<ffffffff8218e256>] kernel_init_freeable+0x18a/0x215
     [<ffffffff8218d983>] ? initcall_blacklist+0xc0/0xc0
     [<ffffffff818a78f0>] ? rest_init+0x80/0x80
     [<ffffffff818a78fe>] kernel_init+0xe/0xf0
     [<ffffffff818c0c3c>] ret_from_fork+0x7c/0xb0
     [<ffffffff818a78f0>] ? rest_init+0x80/0x80
    Code: 45 ac 0f 88 a8 01 00 00 3b b7 d0 01 00 00 49 89 ff 0f 83 99 01 00 00 48 8b 47 20 48 8b 80 88 00 00 00 48 85 c0 0f 84 cd 01 00 00 <41> 8b b1 5c 02 00 00 41 8b 89 58 02 00 00 89 75 98 41 8b b1 60
    RIP  [<ffffffff8150423b>] drm_calc_vbltimestamp_from_scanoutpos+0x4b/0x320
     RSP <ffff880234da7918>
    CR2: 000000000000025c
    ---[ end trace ad2c0aadf48e2032 ]---
    Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000009

It has helped me to add a NULL pointer check that was suggested at
http://lists.freedesktop.org/archives/dri-devel/2014-October/070663.html

I am not familiar with the code. But the change looks sane
and we need something fast at this stage of 3.18 development.

Suggested-by: Helge Deller <deller@gmx.de>
Signed-off-by: Petr Mladek <pmladek@suse.cz>
Tested-by: Petr Mladek <pmladek@suse.cz>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/gpu/drm/radeon/radeon_kms.c |    2 ++
 1 file changed, 2 insertions(+)

--- a/drivers/gpu/drm/radeon/radeon_kms.c
+++ b/drivers/gpu/drm/radeon/radeon_kms.c
@@ -740,6 +740,8 @@ int radeon_get_vblank_timestamp_kms(stru
 
 	/* Get associated drm_crtc: */
 	drmcrtc = &rdev->mode_info.crtcs[crtc]->base;
+	if (!drmcrtc)
+		return -EINVAL;
 
 	/* Helper routine in DRM core does all the work: */
 	return drm_calc_vbltimestamp_from_scanoutpos(dev, crtc, max_error,

[PATCH 3.14 10/34] drm/i915: More cautious with pch fifo underruns

[Greg Kroah-Hartman]

3.14-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Daniel Vetter <daniel.vetter@ffwll.ch>

commit b68362278af94e1171f5be9d4e44988601fb0439 upstream.

Apparently PCH fifo underruns are tricky, we have plenty reports that
we see the occasional underrun (especially at boot-up).

So for a change let's see what happens when we don't re-enable pch
fifo underrun reporting when the pipe is disabled. This means that the
kernel can't catch pch fifo underruns when they happen (except when
all pipes are on on the pch). But we'll still catch underruns when
disabling the pipe again. So not a terrible reduction in test
coverage.

Since the DRM_ERROR is new and hence a regression plan B would be to
revert it back to a debug output. Which would be a lot worse than this
hack for underrun test coverage in the wild. See the referenced
discussions for more.

References: http://mid.gmane.org/CA+gsUGRfGe3t4NcjdeA=qXysrhLY3r4CEu7z4bjTwxi1uOfy+g@mail.gmail.com
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=85898
References: https://bugs.freedesktop.org/show_bug.cgi?id=85898
References: https://bugs.freedesktop.org/show_bug.cgi?id=86233
References: https://bugs.freedesktop.org/show_bug.cgi?id=86478
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Tested-by: lu hua <huax.lu@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/gpu/drm/i915/intel_display.c |    2 --
 1 file changed, 2 deletions(-)

--- a/drivers/gpu/drm/i915/intel_display.c
+++ b/drivers/gpu/drm/i915/intel_display.c
@@ -3817,7 +3817,6 @@ static void ironlake_crtc_disable(struct
 		ironlake_fdi_disable(crtc);
 
 		ironlake_disable_pch_transcoder(dev_priv, pipe);
-		intel_set_pch_fifo_underrun_reporting(dev, pipe, true);
 
 		if (HAS_PCH_CPT(dev)) {
 			/* disable TRANS_DP_CTL */
@@ -3883,7 +3882,6 @@ static void haswell_crtc_disable(struct
 
 	if (intel_crtc->config.has_pch_encoder) {
 		lpt_disable_pch_transcoder(dev_priv);
-		intel_set_pch_fifo_underrun_reporting(dev, TRANSCODER_A, true);
 		intel_ddi_fdi_disable(crtc);
 	}
 

[PATCH 3.14 11/34] drm/i915: Unlock panel even when LVDS is disabled

[Greg Kroah-Hartman]

3.14-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Daniel Vetter <daniel.vetter@ffwll.ch>

commit b0616c5306b342ceca07044dbc4f917d95c4f825 upstream.

Otherwise we'll have backtraces in assert_panel_unlocked because the
BIOS locks the register. In the reporter's case this regression was
introduced in

commit c31407a3672aaebb4acddf90944a114fa5c8af7b
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date:   Thu Oct 18 21:07:01 2012 +0100

    drm/i915: Add no-lvds quirk for Supermicro X7SPA-H

Reported-by: Alexey Orishko <alexey.orishko@gmail.com>
Cc: Alexey Orishko <alexey.orishko@gmail.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Francois Tigeot <ftigeot@wolfpond.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Tested-by: Alexey Orishko <alexey.orishko@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/gpu/drm/i915/intel_lvds.c |   22 +++++++++++-----------
 1 file changed, 11 insertions(+), 11 deletions(-)

--- a/drivers/gpu/drm/i915/intel_lvds.c
+++ b/drivers/gpu/drm/i915/intel_lvds.c
@@ -905,6 +905,17 @@ void intel_lvds_init(struct drm_device *
 	int pipe;
 	u8 pin;
 
+	/*
+	 * Unlock registers and just leave them unlocked. Do this before
+	 * checking quirk lists to avoid bogus WARNINGs.
+	 */
+	if (HAS_PCH_SPLIT(dev)) {
+		I915_WRITE(PCH_PP_CONTROL,
+			   I915_READ(PCH_PP_CONTROL) | PANEL_UNLOCK_REGS);
+	} else {
+		I915_WRITE(PP_CONTROL,
+			   I915_READ(PP_CONTROL) | PANEL_UNLOCK_REGS);
+	}
 	if (!intel_lvds_supported(dev))
 		return;
 
@@ -1099,17 +1110,6 @@ out:
 	DRM_DEBUG_KMS("detected %s-link lvds configuration\n",
 		      lvds_encoder->is_dual_link ? "dual" : "single");
 
-	/*
-	 * Unlock registers and just
-	 * leave them unlocked
-	 */
-	if (HAS_PCH_SPLIT(dev)) {
-		I915_WRITE(PCH_PP_CONTROL,
-			   I915_READ(PCH_PP_CONTROL) | PANEL_UNLOCK_REGS);
-	} else {
-		I915_WRITE(PP_CONTROL,
-			   I915_READ(PP_CONTROL) | PANEL_UNLOCK_REGS);
-	}
 	lvds_connector->lid_notifier.notifier_call = intel_lid_notify;
 	if (acpi_lid_notifier_register(&lvds_connector->lid_notifier)) {
 		DRM_DEBUG_KMS("lid notifier registration failed\n");

[PATCH 3.14 12/34] x86: Use $(OBJDUMP) instead of plain objdump

[Greg Kroah-Hartman]

3.14-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Chris Clayton <chris2553@googlemail.com>

commit e2e68ae688b0a3766cd75aedf4ed4e39be402009 upstream.

commit e6023367d779 'x86, kaslr: Prevent .bss from overlaping initrd'
broke the cross compile of x86. It added a objdump invocation, which
invokes the host native objdump and ignores an active cross tool
chain.

Use $(OBJDUMP) instead which takes the CROSS_COMPILE prefix into
account.

[ tglx: Massage changelog and use $(OBJDUMP) ]

Fixes: e6023367d779 'x86, kaslr: Prevent .bss from overlaping initrd'
Signed-off-by: Chris Clayton <chris2553@googlemail.com>
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Borislav Petkov <bp@suse.de>
Cc: Junjie Mao <eternal.n08@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Link: http://lkml.kernel.org/r/54705C8E.1080400@googlemail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 arch/x86/boot/compressed/Makefile |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

--- a/arch/x86/boot/compressed/Makefile
+++ b/arch/x86/boot/compressed/Makefile
@@ -75,7 +75,7 @@ suffix-$(CONFIG_KERNEL_XZ)	:= xz
 suffix-$(CONFIG_KERNEL_LZO) 	:= lzo
 suffix-$(CONFIG_KERNEL_LZ4) 	:= lz4
 
-RUN_SIZE = $(shell objdump -h vmlinux | \
+RUN_SIZE = $(shell $(OBJDUMP) -h vmlinux | \
 	     perl $(srctree)/arch/x86/tools/calc_run_size.pl)
 quiet_cmd_mkpiggy = MKPIGGY $@
       cmd_mkpiggy = $(obj)/mkpiggy $< $(RUN_SIZE) > $@ || ( rm -f $@ ; false )

[PATCH 3.14 13/34] media: smiapp: Only some selection targets are settable

[Greg Kroah-Hartman]

3.14-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Sakari Ailus <sakari.ailus@iki.fi>

commit b31eb901c4e5eeef4c83c43dfbc7fe0d4348cb21 upstream.

Setting a non-settable selection target caused BUG() to be called. The check
for valid selections only takes the selection target into account, but does
not tell whether it may be set, or only get. Fix the issue by simply
returning an error to the user.

Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/media/i2c/smiapp/smiapp-core.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

--- a/drivers/media/i2c/smiapp/smiapp-core.c
+++ b/drivers/media/i2c/smiapp/smiapp-core.c
@@ -2138,7 +2138,7 @@ static int smiapp_set_selection(struct v
 		ret = smiapp_set_compose(subdev, fh, sel);
 		break;
 	default:
-		BUG();
+		ret = -EINVAL;
 	}
 
 	mutex_unlock(&sensor->mutex);

[PATCH 3.14 14/34] USB: xhci: Reset a halted endpoint immediately when we encounter a stall.

[Greg Kroah-Hartman]

3.14-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Mathias Nyman <mathias.nyman@linux.intel.com>

commit 8e71a322fdb127814bcba423a512914ca5bc6cf5 upstream.

If a device is halted and reuturns a STALL, then the halted endpoint
needs to be cleared both on the host and device side. The host
side halt is cleared by issueing a xhci reset endpoint command. The device side
is cleared with a ClearFeature(ENDPOINT_HALT) request, which should
be issued by the device driver if a URB reruen -EPIPE.

Previously we cleared the host side halt after the device side was cleared.
To make sure the host side halt is cleared in time we want to issue the
reset endpoint command immedialtely when a STALL status is encountered.

Otherwise we end up not following the specs and not returning -EPIPE
several times in a row when trying to transfer data to a halted endpoint.

Fixes: bcef3fd (USB: xhci: Handle errors that cause endpoint halts.)
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/usb/host/xhci-ring.c |   40 +++++++---------------------
 drivers/usb/host/xhci.c      |   60 ++++++++++---------------------------------
 2 files changed, 25 insertions(+), 75 deletions(-)

--- a/drivers/usb/host/xhci-ring.c
+++ b/drivers/usb/host/xhci-ring.c
@@ -1998,22 +1998,13 @@ static int finish_td(struct xhci_hcd *xh
 		ep->stopped_td = td;
 		return 0;
 	} else {
-		if (trb_comp_code == COMP_STALL) {
-			/* The transfer is completed from the driver's
-			 * perspective, but we need to issue a set dequeue
-			 * command for this stalled endpoint to move the dequeue
-			 * pointer past the TD.  We can't do that here because
-			 * the halt condition must be cleared first.  Let the
-			 * USB class driver clear the stall later.
-			 */
-			ep->stopped_td = td;
-			ep->stopped_stream = ep_ring->stream_id;
-		} else if (xhci_requires_manual_halt_cleanup(xhci,
-					ep_ctx, trb_comp_code)) {
-			/* Other types of errors halt the endpoint, but the
-			 * class driver doesn't call usb_reset_endpoint() unless
-			 * the error is -EPIPE.  Clear the halted status in the
-			 * xHCI hardware manually.
+		if (trb_comp_code == COMP_STALL ||
+		    xhci_requires_manual_halt_cleanup(xhci, ep_ctx,
+						      trb_comp_code)) {
+			/* Issue a reset endpoint command to clear the host side
+			 * halt, followed by a set dequeue command to move the
+			 * dequeue pointer past the TD.
+			 * The class driver clears the device side halt later.
 			 */
 			xhci_cleanup_halted_endpoint(xhci,
 					slot_id, ep_index, ep_ring->stream_id,
@@ -2133,9 +2124,7 @@ static int process_ctrl_td(struct xhci_h
 		else
 			td->urb->actual_length = 0;
 
-		xhci_cleanup_halted_endpoint(xhci,
-			slot_id, ep_index, 0, td, event_trb);
-		return finish_td(xhci, td, event_trb, event, ep, status, true);
+		return finish_td(xhci, td, event_trb, event, ep, status, false);
 	}
 	/*
 	 * Did we transfer any data, despite the errors that might have
@@ -2689,17 +2678,8 @@ cleanup:
 		if (ret) {
 			urb = td->urb;
 			urb_priv = urb->hcpriv;
-			/* Leave the TD around for the reset endpoint function
-			 * to use(but only if it's not a control endpoint,
-			 * since we already queued the Set TR dequeue pointer
-			 * command for stalled control endpoints).
-			 */
-			if (usb_endpoint_xfer_control(&urb->ep->desc) ||
-				(trb_comp_code != COMP_STALL &&
-					trb_comp_code != COMP_BABBLE))
-				xhci_urb_free_priv(xhci, urb_priv);
-			else
-				kfree(urb_priv);
+
+			xhci_urb_free_priv(xhci, urb_priv);
 
 			usb_hcd_unlink_urb_from_ep(bus_to_hcd(urb->dev->bus), urb);
 			if ((urb->actual_length != urb->transfer_buffer_length &&
--- a/drivers/usb/host/xhci.c
+++ b/drivers/usb/host/xhci.c
@@ -2925,63 +2925,33 @@ void xhci_cleanup_stalled_ring(struct xh
 	}
 }
 
-/* Deal with stalled endpoints.  The core should have sent the control message
- * to clear the halt condition.  However, we need to make the xHCI hardware
- * reset its sequence number, since a device will expect a sequence number of
- * zero after the halt condition is cleared.
+/* Called when clearing halted device. The core should have sent the control
+ * message to clear the device halt condition. The host side of the halt should
+ * already be cleared with a reset endpoint command issued when the STALL tx
+ * event was received.
+ *
  * Context: in_interrupt
  */
+
 void xhci_endpoint_reset(struct usb_hcd *hcd,
 		struct usb_host_endpoint *ep)
 {
 	struct xhci_hcd *xhci;
-	struct usb_device *udev;
-	unsigned int ep_index;
-	unsigned long flags;
-	int ret;
-	struct xhci_virt_ep *virt_ep;
 
 	xhci = hcd_to_xhci(hcd);
-	udev = (struct usb_device *) ep->hcpriv;
-	/* Called with a root hub endpoint (or an endpoint that wasn't added
-	 * with xhci_add_endpoint()
-	 */
-	if (!ep->hcpriv)
-		return;
-	ep_index = xhci_get_endpoint_index(&ep->desc);
-	virt_ep = &xhci->devs[udev->slot_id]->eps[ep_index];
-	if (!virt_ep->stopped_td) {
-		xhci_dbg_trace(xhci, trace_xhci_dbg_reset_ep,
-			"Endpoint 0x%x not halted, refusing to reset.",
-			ep->desc.bEndpointAddress);
-		return;
-	}
-	if (usb_endpoint_xfer_control(&ep->desc)) {
-		xhci_dbg_trace(xhci, trace_xhci_dbg_reset_ep,
-				"Control endpoint stall already handled.");
-		return;
-	}
 
-	xhci_dbg_trace(xhci, trace_xhci_dbg_reset_ep,
-			"Queueing reset endpoint command");
-	spin_lock_irqsave(&xhci->lock, flags);
-	ret = xhci_queue_reset_ep(xhci, udev->slot_id, ep_index);
 	/*
-	 * Can't change the ring dequeue pointer until it's transitioned to the
-	 * stopped state, which is only upon a successful reset endpoint
-	 * command.  Better hope that last command worked!
+	 * We might need to implement the config ep cmd in xhci 4.8.1 note:
+	 * The Reset Endpoint Command may only be issued to endpoints in the
+	 * Halted state. If software wishes reset the Data Toggle or Sequence
+	 * Number of an endpoint that isn't in the Halted state, then software
+	 * may issue a Configure Endpoint Command with the Drop and Add bits set
+	 * for the target endpoint. that is in the Stopped state.
 	 */
-	if (!ret) {
-		xhci_cleanup_stalled_ring(xhci, udev, ep_index);
-		kfree(virt_ep->stopped_td);
-		xhci_ring_cmd_db(xhci);
-	}
-	virt_ep->stopped_td = NULL;
-	virt_ep->stopped_stream = 0;
-	spin_unlock_irqrestore(&xhci->lock, flags);
 
-	if (ret)
-		xhci_warn(xhci, "FIXME allocate a new ring segment\n");
+	/* For now just print debug to follow the situation */
+	xhci_dbg(xhci, "Endpoint 0x%x ep reset callback called\n",
+		 ep->desc.bEndpointAddress);
 }
 
 static int xhci_check_streams_endpoint(struct xhci_hcd *xhci,

[PATCH 3.14 15/34] AHCI: Add DeviceIDs for Sunrise Point-LP SATA controller

[Greg Kroah-Hartman]

3.14-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Devin Ryles <devin.ryles@intel.com>

commit 249cd0a187ed4ef1d0af7f74362cc2791ec5581b upstream.

This patch adds DeviceIDs for Sunrise Point-LP.

Signed-off-by: Devin Ryles <devin.ryles@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/ata/ahci.c |    3 +++
 1 file changed, 3 insertions(+)

--- a/drivers/ata/ahci.c
+++ b/drivers/ata/ahci.c
@@ -322,6 +322,9 @@ static const struct pci_device_id ahci_p
 	{ PCI_VDEVICE(INTEL, 0x8c87), board_ahci }, /* 9 Series RAID */
 	{ PCI_VDEVICE(INTEL, 0x8c8e), board_ahci }, /* 9 Series RAID */
 	{ PCI_VDEVICE(INTEL, 0x8c8f), board_ahci }, /* 9 Series RAID */
+	{ PCI_VDEVICE(INTEL, 0x9d03), board_ahci }, /* Sunrise Point-LP AHCI */
+	{ PCI_VDEVICE(INTEL, 0x9d05), board_ahci }, /* Sunrise Point-LP RAID */
+	{ PCI_VDEVICE(INTEL, 0x9d07), board_ahci }, /* Sunrise Point-LP RAID */
 	{ PCI_VDEVICE(INTEL, 0xa103), board_ahci }, /* Sunrise Point-H AHCI */
 	{ PCI_VDEVICE(INTEL, 0xa103), board_ahci }, /* Sunrise Point-H RAID */
 	{ PCI_VDEVICE(INTEL, 0xa105), board_ahci }, /* Sunrise Point-H RAID */

[PATCH 3.14 16/34] ahci: disable MSI on SAMSUNG 0xa800 SSD

[Greg Kroah-Hartman]

3.14-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Tejun Heo <tj@kernel.org>

commit 2b21ef0aae65f22f5ba86b13c4588f6f0c2dbefb upstream.

Just like 0x1600 which got blacklisted by 66a7cbc303f4 ("ahci: disable
MSI instead of NCQ on Samsung pci-e SSDs on macbooks"), 0xa800 chokes
on NCQ commands if MSI is enabled.  Disable MSI.

Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Dominik Mierzejewski <dominik@greysector.net>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=89171
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/ata/ahci.c |    1 +
 1 file changed, 1 insertion(+)

--- a/drivers/ata/ahci.c
+++ b/drivers/ata/ahci.c
@@ -496,6 +496,7 @@ static const struct pci_device_id ahci_p
 	 * enabled.  https://bugzilla.kernel.org/show_bug.cgi?id=60731
 	 */
 	{ PCI_VDEVICE(SAMSUNG, 0x1600), board_ahci_nomsi },
+	{ PCI_VDEVICE(SAMSUNG, 0xa800), board_ahci_nomsi },
 
 	/* Enmotus */
 	{ PCI_DEVICE(0x1c44, 0x8000), board_ahci },

[PATCH 3.14 17/34] sata_fsl: fix error handling of irq_of_parse_and_map

[Greg Kroah-Hartman]

3.14-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Dmitry Torokhov <dtor@chromium.org>

commit aad0b624129709c94c2e19e583b6053520353fa8 upstream.

irq_of_parse_and_map() returns 0 on error (the result is unsigned int),
so testing for negative result never works.

Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/ata/sata_fsl.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

--- a/drivers/ata/sata_fsl.c
+++ b/drivers/ata/sata_fsl.c
@@ -1503,7 +1503,7 @@ static int sata_fsl_probe(struct platfor
 	host_priv->csr_base = csr_base;
 
 	irq = irq_of_parse_and_map(ofdev->dev.of_node, 0);
-	if (irq < 0) {
+	if (!irq) {
 		dev_err(&ofdev->dev, "invalid irq from platform\n");
 		goto error_exit_with_cleanup;
 	}

[PATCH 3.14 18/34] ip_tunnel: the lack of vti_link_ops dellink() cause kernel panic

[Greg Kroah-Hartman]

3.14-stable review patch.  If anyone has any objections, please let me know.

------------------

From: lucien <lucien.xin@gmail.com>

[ Upstream commit 20ea60ca9952bd19d4b0d74719daba305aef5178 ]

Now the vti_link_ops do not point the .dellink, for fb tunnel device
(ip_vti0), the net_device will be removed as the default .dellink is
unregister_netdevice_queue,but the tunnel still in the tunnel list,
then if we add a new vti tunnel, in ip_tunnel_find():

        hlist_for_each_entry_rcu(t, head, hash_node) {
                if (local == t->parms.iph.saddr &&
                    remote == t->parms.iph.daddr &&
                    link == t->parms.link &&
==>                 type == t->dev->type &&
                    ip_tunnel_key_match(&t->parms, flags, key))
                        break;
        }

the panic will happen, cause dev of ip_tunnel *t is null:
[ 3835.072977] IP: [<ffffffffa04103fd>] ip_tunnel_find+0x9d/0xc0 [ip_tunnel]
[ 3835.073008] PGD b2c21067 PUD b7277067 PMD 0
[ 3835.073008] Oops: 0000 [#1] SMP
.....
[ 3835.073008] Stack:
[ 3835.073008]  ffff8800b72d77f0 ffffffffa0411924 ffff8800bb956000 ffff8800b72d78e0
[ 3835.073008]  ffff8800b72d78a0 0000000000000000 ffffffffa040d100 ffff8800b72d7858
[ 3835.073008]  ffffffffa040b2e3 0000000000000000 0000000000000000 0000000000000000
[ 3835.073008] Call Trace:
[ 3835.073008]  [<ffffffffa0411924>] ip_tunnel_newlink+0x64/0x160 [ip_tunnel]
[ 3835.073008]  [<ffffffffa040b2e3>] vti_newlink+0x43/0x70 [ip_vti]
[ 3835.073008]  [<ffffffff8150d4da>] rtnl_newlink+0x4fa/0x5f0
[ 3835.073008]  [<ffffffff812f68bb>] ? nla_strlcpy+0x5b/0x70
[ 3835.073008]  [<ffffffff81508fb0>] ? rtnl_link_ops_get+0x40/0x60
[ 3835.073008]  [<ffffffff8150d11f>] ? rtnl_newlink+0x13f/0x5f0
[ 3835.073008]  [<ffffffff81509cf4>] rtnetlink_rcv_msg+0xa4/0x270
[ 3835.073008]  [<ffffffff8126adf5>] ? sock_has_perm+0x75/0x90
[ 3835.073008]  [<ffffffff81509c50>] ? rtnetlink_rcv+0x30/0x30
[ 3835.073008]  [<ffffffff81529e39>] netlink_rcv_skb+0xa9/0xc0
[ 3835.073008]  [<ffffffff81509c48>] rtnetlink_rcv+0x28/0x30
....

modprobe ip_vti
ip link del ip_vti0 type vti
ip link add ip_vti0 type vti
rmmod ip_vti

do that one or more times, kernel will panic.

fix it by assigning ip_tunnel_dellink to vti_link_ops' dellink, in
which we skip the unregister of fb tunnel device. do the same on ip6_vti.

Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 net/ipv4/ip_vti.c  |    1 +
 net/ipv6/ip6_vti.c |   11 +++++++++++
 2 files changed, 12 insertions(+)

--- a/net/ipv4/ip_vti.c
+++ b/net/ipv4/ip_vti.c
@@ -369,6 +369,7 @@ static struct rtnl_link_ops vti_link_ops
 	.validate	= vti_tunnel_validate,
 	.newlink	= vti_newlink,
 	.changelink	= vti_changelink,
+	.dellink        = ip_tunnel_dellink,
 	.get_size	= vti_get_size,
 	.fill_info	= vti_fill_info,
 };
--- a/net/ipv6/ip6_vti.c
+++ b/net/ipv6/ip6_vti.c
@@ -825,6 +825,15 @@ static int vti6_newlink(struct net *src_
 	return vti6_tnl_create2(dev);
 }
 
+static void vti6_dellink(struct net_device *dev, struct list_head *head)
+{
+	struct net *net = dev_net(dev);
+	struct vti6_net *ip6n = net_generic(net, vti6_net_id);
+
+	if (dev != ip6n->fb_tnl_dev)
+		unregister_netdevice_queue(dev, head);
+}
+
 static int vti6_changelink(struct net_device *dev, struct nlattr *tb[],
 			   struct nlattr *data[])
 {
@@ -900,6 +909,7 @@ static struct rtnl_link_ops vti6_link_op
 	.setup		= vti6_dev_setup,
 	.validate	= vti6_validate,
 	.newlink	= vti6_newlink,
+	.dellink	= vti6_dellink,
 	.changelink	= vti6_changelink,
 	.get_size	= vti6_get_size,
 	.fill_info	= vti6_fill_info,
@@ -945,6 +955,7 @@ static int __net_init vti6_init_net(stru
 	if (!ip6n->fb_tnl_dev)
 		goto err_alloc_dev;
 	dev_net_set(ip6n->fb_tnl_dev, net);
+	ip6n->fb_tnl_dev->rtnl_link_ops = &vti6_link_ops;
 
 	err = vti6_fb_tnl_dev_init(ip6n->fb_tnl_dev);
 	if (err < 0)

[PATCH 3.14 19/34] ipv6: gre: fix wrong skb->protocol in WCCP

[Greg Kroah-Hartman]

3.14-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Yuri Chislov <yuri.chislov@gmail.com>

[ Upstream commit be6572fdb1bfbe23b2624d477de50af50b02f5d6 ]

When using GRE redirection in WCCP, it sets the wrong skb->protocol,
that is, ETH_P_IP instead of ETH_P_IPV6 for the encapuslated traffic.

Fixes: c12b395a4664 ("gre: Support GRE over IPv6")
Cc: Dmitry Kozlov <xeb@mail.ru>
Signed-off-by: Yuri Chislov <yuri.chislov@gmail.com>
Tested-by: Yuri Chislov <yuri.chislov@gmail.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 net/ipv6/ip6_gre.c |    4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

--- a/net/ipv6/ip6_gre.c
+++ b/net/ipv6/ip6_gre.c
@@ -508,11 +508,11 @@ static int ip6gre_rcv(struct sk_buff *sk
 
 		skb->protocol = gre_proto;
 		/* WCCP version 1 and 2 protocol decoding.
-		 * - Change protocol to IP
+		 * - Change protocol to IPv6
 		 * - When dealing with WCCPv2, Skip extra 4 bytes in GRE header
 		 */
 		if (flags == 0 && gre_proto == htons(ETH_P_WCCP)) {
-			skb->protocol = htons(ETH_P_IP);
+			skb->protocol = htons(ETH_P_IPV6);
 			if ((*(h + offset) & 0xF0) != 0x40)
 				offset += 4;
 		}

[PATCH 3.14 20/34] Fix race condition between vxlan_sock_add and vxlan_sock_release

[Greg Kroah-Hartman]

3.14-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Marcelo Leitner <mleitner@redhat.com>

[ Upstream commit 00c83b01d58068dfeb2e1351cca6fccf2a83fa8f ]

Currently, when trying to reuse a socket, vxlan_sock_add will grab
vn->sock_lock, locate a reusable socket, inc refcount and release
vn->sock_lock.

But vxlan_sock_release() will first decrement refcount, and then grab
that lock. refcnt operations are atomic but as currently we have
deferred works which hold vs->refcnt each, this might happen, leading to
a use after free (specially after vxlan_igmp_leave):

  CPU 1                            CPU 2

deferred work                    vxlan_sock_add
  ...                              ...
                                   spin_lock(&vn->sock_lock)
                                   vs = vxlan_find_sock();
  vxlan_sock_release
    dec vs->refcnt, reaches 0
    spin_lock(&vn->sock_lock)
                                   vxlan_sock_hold(vs), refcnt=1
                                   spin_unlock(&vn->sock_lock)
    hlist_del_rcu(&vs->hlist);
    vxlan_notify_del_rx_port(vs)
    spin_unlock(&vn->sock_lock)

So when we look for a reusable socket, we check if it wasn't freed
already before reusing it.

Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Fixes: 7c47cedf43a8b3 ("vxlan: move IGMP join/leave to work queue")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/net/vxlan.c |   10 +++-------
 1 file changed, 3 insertions(+), 7 deletions(-)

--- a/drivers/net/vxlan.c
+++ b/drivers/net/vxlan.c
@@ -2106,9 +2106,8 @@ static int vxlan_init(struct net_device
 	spin_lock(&vn->sock_lock);
 	vs = vxlan_find_sock(dev_net(dev), ipv6 ? AF_INET6 : AF_INET,
 			     vxlan->dst_port);
-	if (vs) {
+	if (vs && atomic_add_unless(&vs->refcnt, 1, 0)) {
 		/* If we have a socket with same port already, reuse it */
-		atomic_inc(&vs->refcnt);
 		vxlan_vs_add_dev(vs, vxlan);
 	} else {
 		/* otherwise make new socket outside of RTNL */
@@ -2574,12 +2573,9 @@ struct vxlan_sock *vxlan_sock_add(struct
 
 	spin_lock(&vn->sock_lock);
 	vs = vxlan_find_sock(net, ipv6 ? AF_INET6 : AF_INET, port);
-	if (vs) {
-		if (vs->rcv == rcv)
-			atomic_inc(&vs->refcnt);
-		else
+	if (vs && ((vs->rcv != rcv) ||
+		   !atomic_add_unless(&vs->refcnt, 1, 0)))
 			vs = ERR_PTR(-EBUSY);
-	}
 	spin_unlock(&vn->sock_lock);
 
 	if (!vs)

[PATCH 3.14 21/34] tg3: fix ring init when there are more TX than RX channels

[Greg Kroah-Hartman]

3.14-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>

[ Upstream commit a620a6bc1c94c22d6c312892be1e0ae171523125 ]

If TX channels are set to 4 and RX channels are set to less than 4,
using ethtool -L, the driver will try to initialize more RX channels
than it has allocated, causing an oops.

This fix only initializes the RX ring if it has been allocated.

Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/net/ethernet/broadcom/tg3.c |    3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

--- a/drivers/net/ethernet/broadcom/tg3.c
+++ b/drivers/net/ethernet/broadcom/tg3.c
@@ -8548,7 +8548,8 @@ static int tg3_init_rings(struct tg3 *tp
 		if (tnapi->rx_rcb)
 			memset(tnapi->rx_rcb, 0, TG3_RX_RCB_RING_BYTES(tp));
 
-		if (tg3_rx_prodring_alloc(tp, &tnapi->prodring)) {
+		if (tnapi->prodring.rx_std &&
+		    tg3_rx_prodring_alloc(tp, &tnapi->prodring)) {
 			tg3_free_rings(tp);
 			return -ENOMEM;
 		}

[PATCH 3.14 22/34] net/mlx4_core: Limit count field to 24 bits in qp_alloc_res

[Greg Kroah-Hartman]

3.14-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Jack Morgenstein <jackm@dev.mellanox.co.il>

[ Upstream commit 2d5c57d7fbfaa642fb7f0673df24f32b83d9066c ]

Some VF drivers use the upper byte of "param1" (the qp count field)
in mlx4_qp_reserve_range() to pass flags which are used to optimize
the range allocation.

Under the current code, if any of these flags are set, the 32-bit
count field yields a count greater than 2^24, which is out of range,
and this VF fails.

As these flags represent a "best-effort" allocation hint anyway, they may
safely be ignored. Therefore, the PF driver may simply mask out the bits.

Fixes: c82e9aa0a8 "mlx4_core: resource tracking for HCA resources used by guests"
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/net/ethernet/mellanox/mlx4/resource_tracker.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

--- a/drivers/net/ethernet/mellanox/mlx4/resource_tracker.c
+++ b/drivers/net/ethernet/mellanox/mlx4/resource_tracker.c
@@ -1456,7 +1456,7 @@ static int qp_alloc_res(struct mlx4_dev
 
 	switch (op) {
 	case RES_OP_RESERVE:
-		count = get_param_l(&in_param);
+		count = get_param_l(&in_param) & 0xffffff;
 		align = get_param_h(&in_param);
 		err = mlx4_grant_resource(dev, slave, RES_QP, count, 0);
 		if (err)

[PATCH 3.14 23/34] rtnetlink: release net refcnt on error in do_setlink()

[Greg Kroah-Hartman]

3.14-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Nicolas Dichtel <nicolas.dichtel@6wind.com>

[ Upstream commit e0ebde0e131b529fd721b24f62872def5ec3718c ]

rtnl_link_get_net() holds a reference on the 'struct net', we need to release
it in case of error.

CC: Eric W. Biederman <ebiederm@xmission.com>
Fixes: b51642f6d77b ("net: Enable a userns root rtnl calls that are safe for unprivilged users")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 net/core/rtnetlink.c |    1 +
 1 file changed, 1 insertion(+)

--- a/net/core/rtnetlink.c
+++ b/net/core/rtnetlink.c
@@ -1453,6 +1453,7 @@ static int do_setlink(const struct sk_bu
 			goto errout;
 		}
 		if (!netlink_ns_capable(skb, net->user_ns, CAP_NET_ADMIN)) {
+			put_net(net);
 			err = -EPERM;
 			goto errout;
 		}

[PATCH 3.14 24/34] gre: Set inner mac header in gro complete

[Greg Kroah-Hartman]

3.14-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Tom Herbert <therbert@google.com>

[ Upstream commit 6fb2a756739aa507c1fd5b8126f0bfc2f070dc46 ]

Set the inner mac header to point to the GRE payload when
doing GRO. This is needed if we proceed to send the packet
through GRE GSO which now uses the inner mac header instead
of inner network header to determine the length of encapsulation
headers.

Fixes: 14051f0452a2 ("gre: Use inner mac length when computing tunnel length")
Reported-by: Wolfgang Walter <linux@stwm.de>
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 net/ipv4/gre_offload.c |    3 +++
 1 file changed, 3 insertions(+)

--- a/net/ipv4/gre_offload.c
+++ b/net/ipv4/gre_offload.c
@@ -271,6 +271,9 @@ static int gre_gro_complete(struct sk_bu
 		err = ptype->callbacks.gro_complete(skb, nhoff + grehlen);
 
 	rcu_read_unlock();
+
+	skb_set_inner_mac_header(skb, nhoff + grehlen);
+
 	return err;
 }
 

[PATCH 3.14 25/34] net: mvneta: fix Tx interrupt delay

[Greg Kroah-Hartman]

3.14-stable review patch.  If anyone has any objections, please let me know.

------------------

From: willy tarreau <w@1wt.eu>

[ Upstream commit aebea2ba0f7495e1a1c9ea5e753d146cb2f6b845 ]

The mvneta driver sets the amount of Tx coalesce packets to 16 by
default. Normally that does not cause any trouble since the driver
uses a much larger Tx ring size (532 packets). But some sockets
might run with very small buffers, much smaller than the equivalent
of 16 packets. This is what ping is doing for example, by setting
SNDBUF to 324 bytes rounded up to 2kB by the kernel.

The problem is that there is no documented method to force a specific
packet to emit an interrupt (eg: the last of the ring) nor is it
possible to make the NIC emit an interrupt after a given delay.

In this case, it causes trouble, because when ping sends packets over
its raw socket, the few first packets leave the system, and the first
15 packets will be emitted without an IRQ being generated, so without
the skbs being freed. And since the socket's buffer is small, there's
no way to reach that amount of packets, and the ping ends up with
"send: no buffer available" after sending 6 packets. Running with 3
instances of ping in parallel is enough to hide the problem, because
with 6 packets per instance, that's 18 packets total, which is enough
to grant a Tx interrupt before all are sent.

The original driver in the LSP kernel worked around this design flaw
by using a software timer to clean up the Tx descriptors. This timer
was slow and caused terrible network performance on some Tx-bound
workloads (such as routing) but was enough to make tools like ping
work correctly.

Instead here, we simply set the packet counts before interrupt to 1.
This ensures that each packet sent will produce an interrupt. NAPI
takes care of coalescing interrupts since the interrupt is disabled
once generated.

No measurable performance impact nor CPU usage were observed on small
nor large packets, including when saturating the link on Tx, and this
fixes tools like ping which rely on too small a send buffer. If one
wants to increase this value for certain workloads where it is safe
to do so, "ethtool -C $dev tx-frames" will override this default
setting.

This fix needs to be applied to stable kernels starting with 3.10.

Tested-By: Maggie Mae Roxas <maggie.mae.roxas@gmail.com>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/net/ethernet/marvell/mvneta.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

--- a/drivers/net/ethernet/marvell/mvneta.c
+++ b/drivers/net/ethernet/marvell/mvneta.c
@@ -213,7 +213,7 @@
 /* Various constants */
 
 /* Coalescing */
-#define MVNETA_TXDONE_COAL_PKTS		16
+#define MVNETA_TXDONE_COAL_PKTS		1
 #define MVNETA_RX_COAL_PKTS		32
 #define MVNETA_RX_COAL_USEC		100
 

[PATCH 3.14 26/34] net: mvneta: fix race condition in mvneta_tx()

[Greg Kroah-Hartman]

3.14-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Eric Dumazet <edumazet@google.com>

[ Upstream commit 5f478b41033606d325e420df693162e2524c2b94 ]

mvneta_tx() dereferences skb to get skb->len too late,
as hardware might have completed the transmit and TX completion
could have freed the skb from another cpu.

Fixes: 71f6d1b31fb1 ("net: mvneta: replace Tx timer with a real interrupt")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/net/ethernet/marvell/mvneta.c |    3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

--- a/drivers/net/ethernet/marvell/mvneta.c
+++ b/drivers/net/ethernet/marvell/mvneta.c
@@ -1612,6 +1612,7 @@ static int mvneta_tx(struct sk_buff *skb
 	u16 txq_id = skb_get_queue_mapping(skb);
 	struct mvneta_tx_queue *txq = &pp->txqs[txq_id];
 	struct mvneta_tx_desc *tx_desc;
+	int len = skb->len;
 	struct netdev_queue *nq;
 	int frags = 0;
 	u32 tx_cmd;
@@ -1675,7 +1676,7 @@ out:
 
 		u64_stats_update_begin(&stats->syncp);
 		stats->tx_packets++;
-		stats->tx_bytes  += skb->len;
+		stats->tx_bytes  += len;
 		u64_stats_update_end(&stats->syncp);
 	} else {
 		dev->stats.tx_dropped++;

[PATCH 3.14 28/34] perf/x86/intel: Protect LBR and extra_regs against KVM lying

[Greg Kroah-Hartman]

3.14-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Kan Liang <kan.liang@intel.com>

commit 338b522ca43cfd32d11a370f4203bcd089c6c877 upstream.

With -cpu host, KVM reports LBR and extra_regs support, if the host has
support.

When the guest perf driver tries to access LBR or extra_regs MSR,
it #GPs all MSR accesses,since KVM doesn't handle LBR and extra_regs support.
So check the related MSRs access right once at initialization time to avoid
the error access at runtime.

For reproducing the issue, please build the kernel with CONFIG_KVM_INTEL = y
(for host kernel).
And CONFIG_PARAVIRT = n and CONFIG_KVM_GUEST = n (for guest kernel).
Start the guest with -cpu host.
Run perf record with --branch-any or --branch-filter in guest to trigger LBR
Run perf stat offcore events (E.g. LLC-loads/LLC-load-misses ...) in guest to
trigger offcore_rsp #GP

Signed-off-by: Kan Liang <kan.liang@intel.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Maria Dimakopoulou <maria.n.dimakopoulou@gmail.com>
Cc: Mark Davies <junk@eslaf.co.uk>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Yan, Zheng <zheng.z.yan@intel.com>
Link: http://lkml.kernel.org/r/1405365957-20202-1-git-send-email-kan.liang@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Dongsu Park <dongsu.park@profitbricks.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 arch/x86/kernel/cpu/perf_event.c       |    3 +
 arch/x86/kernel/cpu/perf_event.h       |   12 +++---
 arch/x86/kernel/cpu/perf_event_intel.c |   66 ++++++++++++++++++++++++++++++++-
 3 files changed, 75 insertions(+), 6 deletions(-)

--- a/arch/x86/kernel/cpu/perf_event.c
+++ b/arch/x86/kernel/cpu/perf_event.c
@@ -118,6 +118,9 @@ static int x86_pmu_extra_regs(u64 config
 			continue;
 		if (event->attr.config1 & ~er->valid_mask)
 			return -EINVAL;
+		/* Check if the extra msrs can be safely accessed*/
+		if (!er->extra_msr_access)
+			return -ENXIO;
 
 		reg->idx = er->idx;
 		reg->config = event->attr.config1;
--- a/arch/x86/kernel/cpu/perf_event.h
+++ b/arch/x86/kernel/cpu/perf_event.h
@@ -293,14 +293,16 @@ struct extra_reg {
 	u64			config_mask;
 	u64			valid_mask;
 	int			idx;  /* per_xxx->regs[] reg index */
+	bool			extra_msr_access;
 };
 
 #define EVENT_EXTRA_REG(e, ms, m, vm, i) {	\
-	.event = (e),		\
-	.msr = (ms),		\
-	.config_mask = (m),	\
-	.valid_mask = (vm),	\
-	.idx = EXTRA_REG_##i,	\
+	.event = (e),			\
+	.msr = (ms),			\
+	.config_mask = (m),		\
+	.valid_mask = (vm),		\
+	.idx = EXTRA_REG_##i,		\
+	.extra_msr_access = true,	\
 	}
 
 #define INTEL_EVENT_EXTRA_REG(event, msr, vm, idx)	\
--- a/arch/x86/kernel/cpu/perf_event_intel.c
+++ b/arch/x86/kernel/cpu/perf_event_intel.c
@@ -2183,6 +2183,41 @@ static void intel_snb_check_microcode(vo
 	}
 }
 
+/*
+ * Under certain circumstances, access certain MSR may cause #GP.
+ * The function tests if the input MSR can be safely accessed.
+ */
+static bool check_msr(unsigned long msr, u64 mask)
+{
+	u64 val_old, val_new, val_tmp;
+
+	/*
+	 * Read the current value, change it and read it back to see if it
+	 * matches, this is needed to detect certain hardware emulators
+	 * (qemu/kvm) that don't trap on the MSR access and always return 0s.
+	 */
+	if (rdmsrl_safe(msr, &val_old))
+		return false;
+
+	/*
+	 * Only change the bits which can be updated by wrmsrl.
+	 */
+	val_tmp = val_old ^ mask;
+	if (wrmsrl_safe(msr, val_tmp) ||
+	    rdmsrl_safe(msr, &val_new))
+		return false;
+
+	if (val_new != val_tmp)
+		return false;
+
+	/* Here it's sure that the MSR can be safely accessed.
+	 * Restore the old value and return.
+	 */
+	wrmsrl(msr, val_old);
+
+	return true;
+}
+
 static __init void intel_sandybridge_quirk(void)
 {
 	x86_pmu.check_microcode = intel_snb_check_microcode;
@@ -2272,7 +2307,8 @@ __init int intel_pmu_init(void)
 	union cpuid10_ebx ebx;
 	struct event_constraint *c;
 	unsigned int unused;
-	int version;
+	struct extra_reg *er;
+	int version, i;
 
 	if (!cpu_has(&boot_cpu_data, X86_FEATURE_ARCH_PERFMON)) {
 		switch (boot_cpu_data.x86) {
@@ -2578,6 +2614,34 @@ __init int intel_pmu_init(void)
 		}
 	}
 
+	/*
+	 * Access LBR MSR may cause #GP under certain circumstances.
+	 * E.g. KVM doesn't support LBR MSR
+	 * Check all LBT MSR here.
+	 * Disable LBR access if any LBR MSRs can not be accessed.
+	 */
+	if (x86_pmu.lbr_nr && !check_msr(x86_pmu.lbr_tos, 0x3UL))
+		x86_pmu.lbr_nr = 0;
+	for (i = 0; i < x86_pmu.lbr_nr; i++) {
+		if (!(check_msr(x86_pmu.lbr_from + i, 0xffffUL) &&
+		      check_msr(x86_pmu.lbr_to + i, 0xffffUL)))
+			x86_pmu.lbr_nr = 0;
+	}
+
+	/*
+	 * Access extra MSR may cause #GP under certain circumstances.
+	 * E.g. KVM doesn't support offcore event
+	 * Check all extra_regs here.
+	 */
+	if (x86_pmu.extra_regs) {
+		for (er = x86_pmu.extra_regs; er->msr; er++) {
+			er->extra_msr_access = check_msr(er->msr, 0x1ffUL);
+			/* Disable LBR select mapping */
+			if ((er->idx == EXTRA_REG_LBR) && !er->extra_msr_access)
+				x86_pmu.lbr_sel_map = NULL;
+		}
+	}
+
 	/* Support full width counters using alternative MSR range */
 	if (x86_pmu.intel_cap.full_width_write) {
 		x86_pmu.max_period = x86_pmu.cntval_mask;

[PATCH 3.14 29/34] igb: bring link up when PHY is powered up

[Greg Kroah-Hartman]

3.14-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Todd Fujinaka <todd.fujinaka@intel.com>

commit aec653c43b0c55667355e26d7de1236bda9fb4e3 upstream.

Call igb_setup_link() when the PHY is powered up.

Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Reported-by: Jeff Westfahl <jeff.westfahl@ni.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Vincent Donnefort <vdonnefort@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/net/ethernet/intel/igb/igb_main.c |    2 ++
 1 file changed, 2 insertions(+)

--- a/drivers/net/ethernet/intel/igb/igb_main.c
+++ b/drivers/net/ethernet/intel/igb/igb_main.c
@@ -1613,6 +1613,8 @@ void igb_power_up_link(struct igb_adapte
 		igb_power_up_phy_copper(&adapter->hw);
 	else
 		igb_power_up_serdes_link_82575(&adapter->hw);
+
+	igb_setup_link(&adapter->hw);
 }
 
 /**

[PATCH 3.14 30/34] powerpc: 32 bit getcpu VDSO function uses 64 bit instructions

[Greg Kroah-Hartman]

3.14-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Anton Blanchard <anton@samba.org>

commit 152d44a853e42952f6c8a504fb1f8eefd21fd5fd upstream.

I used some 64 bit instructions when adding the 32 bit getcpu VDSO
function. Fix it.

Fixes: 18ad51dd342a ("powerpc: Add VDSO version of getcpu")
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 arch/powerpc/kernel/vdso32/getcpu.S |    4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

--- a/arch/powerpc/kernel/vdso32/getcpu.S
+++ b/arch/powerpc/kernel/vdso32/getcpu.S
@@ -30,8 +30,8 @@
 V_FUNCTION_BEGIN(__kernel_getcpu)
   .cfi_startproc
 	mfspr	r5,SPRN_USPRG3
-	cmpdi	cr0,r3,0
-	cmpdi	cr1,r4,0
+	cmpwi	cr0,r3,0
+	cmpwi	cr1,r4,0
 	clrlwi  r6,r5,16
 	rlwinm  r7,r5,16,31-15,31-0
 	beq	cr0,1f

[PATCH 3.14 31/34] mac80211: Fix regression that triggers a kernel BUG with CCMP

[Greg Kroah-Hartman]

3.14-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Ronald Wahl <ronald.wahl@raritan.com>

commit 4f031fa9f188b2b0641ac20087d9e16bcfb4e49d upstream.

Commit 7ec7c4a9a686c608315739ab6a2b0527a240883c (mac80211: port CCMP to
cryptoapi's CCM driver) introduced a regression when decrypting empty
packets (data_len == 0). This will lead to backtraces like:

(scatterwalk_start) from [<c01312f4>] (scatterwalk_map_and_copy+0x2c/0xa8)
(scatterwalk_map_and_copy) from [<c013a5a0>] (crypto_ccm_decrypt+0x7c/0x25c)
(crypto_ccm_decrypt) from [<c032886c>] (ieee80211_aes_ccm_decrypt+0x160/0x170)
(ieee80211_aes_ccm_decrypt) from [<c031c628>] (ieee80211_crypto_ccmp_decrypt+0x1ac/0x238)
(ieee80211_crypto_ccmp_decrypt) from [<c032ef28>] (ieee80211_rx_handlers+0x870/0x1d24)
(ieee80211_rx_handlers) from [<c0330c7c>] (ieee80211_prepare_and_rx_handle+0x8a0/0x91c)
(ieee80211_prepare_and_rx_handle) from [<c0331260>] (ieee80211_rx+0x568/0x730)
(ieee80211_rx) from [<c01d3054>] (__carl9170_rx+0x94c/0xa20)
(__carl9170_rx) from [<c01d3324>] (carl9170_rx_stream+0x1fc/0x320)
(carl9170_rx_stream) from [<c01cbccc>] (carl9170_usb_tasklet+0x80/0xc8)
(carl9170_usb_tasklet) from [<c00199dc>] (tasklet_hi_action+0x88/0xcc)
(tasklet_hi_action) from [<c00193c8>] (__do_softirq+0xcc/0x200)
(__do_softirq) from [<c0019734>] (irq_exit+0x80/0xe0)
(irq_exit) from [<c0009c10>] (handle_IRQ+0x64/0x80)
(handle_IRQ) from [<c000c3a0>] (__irq_svc+0x40/0x4c)
(__irq_svc) from [<c0009d44>] (arch_cpu_idle+0x2c/0x34)

Such packets can appear for example when using the carl9170 wireless driver
because hardware sometimes generates garbage when the internal FIFO overruns.

This patch adds an additional length check.

Fixes: 7ec7c4a9a686 ("mac80211: port CCMP to cryptoapi's CCM driver")
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Ronald Wahl <ronald.wahl@raritan.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>


---
 net/mac80211/aes_ccm.c |    3 +++
 1 file changed, 3 insertions(+)

--- a/net/mac80211/aes_ccm.c
+++ b/net/mac80211/aes_ccm.c
@@ -54,6 +54,9 @@ int ieee80211_aes_ccm_decrypt(struct cry
 
 	memset(&aead_req, 0, sizeof(aead_req));
 
+	if (data_len == 0)
+		return -EINVAL;
+
 	sg_init_one(&pt, data, data_len);
 	sg_init_one(&assoc, &aad[2], be16_to_cpup((__be16 *)aad));
 	sg_init_table(ct, 2);

[PATCH 3.14 32/34] ALSA: hda - Add EAPD fixup for ASUS Z99He laptop

[Greg Kroah-Hartman]

3.14-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Takashi Iwai <tiwai@suse.de>

commit f62f5eff3d40a56ad1cf0d81a6cac8dd8743e8a1 upstream.

The same fixup to enable EAPD is needed for ASUS Z99He with AD1986A
codec like another ASUS machine.

Reported-and-tested-by: Dmitry V. Zimin <pfzim@mail.ru>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 sound/pci/hda/patch_analog.c |    1 +
 1 file changed, 1 insertion(+)

--- a/sound/pci/hda/patch_analog.c
+++ b/sound/pci/hda/patch_analog.c
@@ -333,6 +333,7 @@ static const struct hda_fixup ad1986a_fi
 
 static const struct snd_pci_quirk ad1986a_fixup_tbl[] = {
 	SND_PCI_QUIRK(0x103c, 0x30af, "HP B2800", AD1986A_FIXUP_LAPTOP_IMIC),
+	SND_PCI_QUIRK(0x1043, 0x1443, "ASUS Z99He", AD1986A_FIXUP_EAPD),
 	SND_PCI_QUIRK(0x1043, 0x1447, "ASUS A8JN", AD1986A_FIXUP_EAPD),
 	SND_PCI_QUIRK_MASK(0x1043, 0xff00, 0x8100, "ASUS P5", AD1986A_FIXUP_3STACK),
 	SND_PCI_QUIRK_MASK(0x1043, 0xff00, 0x8200, "ASUS M2", AD1986A_FIXUP_3STACK),

[PATCH 3.14 33/34] ALSA: hda - Fix built-in mic at resume on Lenovo Ideapad S210

[Greg Kroah-Hartman]

3.14-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Takashi Iwai <tiwai@suse.de>

commit fedb2245cbb8d823e449ebdd48ba9bb35c071ce0 upstream.

The built-in mic boost volume gets almost muted after suspend/resume
on Lenovo Ideapad S210.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=88121
Reported-and-tested-by: Roman Kagan <rkagan@mail.ru>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 sound/pci/hda/patch_realtek.c |    1 +
 1 file changed, 1 insertion(+)

--- a/sound/pci/hda/patch_realtek.c
+++ b/sound/pci/hda/patch_realtek.c
@@ -4554,6 +4554,7 @@ static const struct snd_pci_quirk alc269
 	SND_PCI_QUIRK(0x17aa, 0x2212, "Thinkpad", ALC269_FIXUP_LIMIT_INT_MIC_BOOST),
 	SND_PCI_QUIRK(0x17aa, 0x2214, "Thinkpad", ALC269_FIXUP_LIMIT_INT_MIC_BOOST),
 	SND_PCI_QUIRK(0x17aa, 0x2215, "Thinkpad", ALC269_FIXUP_LIMIT_INT_MIC_BOOST),
+	SND_PCI_QUIRK(0x17aa, 0x3977, "IdeaPad S210", ALC283_FIXUP_INT_MIC),
 	SND_PCI_QUIRK(0x17aa, 0x3978, "IdeaPad Y410P", ALC269_FIXUP_NO_SHUTUP),
 	SND_PCI_QUIRK(0x17aa, 0x5013, "Thinkpad", ALC269_FIXUP_LIMIT_INT_MIC_BOOST),
 	SND_PCI_QUIRK(0x17aa, 0x501a, "Thinkpad", ALC283_FIXUP_INT_MIC),

[PATCH 3.14 34/34] ALSA: usb-audio: Dont resubmit pending URBs at MIDI error recovery

[Greg Kroah-Hartman]

3.14-stable review patch.  If anyone has any objections, please let me know.

------------------

From: Takashi Iwai <tiwai@suse.de>

commit 66139a48cee1530c91f37c145384b4ee7043f0b7 upstream.

In snd_usbmidi_error_timer(), the driver tries to resubmit MIDI input
URBs to reactivate the MIDI stream, but this causes the error when
some of URBs are still pending like:

 WARNING: CPU: 0 PID: 0 at ../drivers/usb/core/urb.c:339 usb_submit_urb+0x5f/0x70()
 URB ef705c40 submitted while active
 CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.16.6-2-desktop #1
 Hardware name: FOXCONN TPS01/TPS01, BIOS 080015  03/23/2010
  c0984bfa f4009ed4 c078deaf f4009ee4 c024c884 c09a135c f4009f00 00000000
  c0984bfa 00000153 c061ac4f c061ac4f 00000009 00000001 ef705c40 e854d1c0
  f4009eec c024c8d3 00000009 f4009ee4 c09a135c f4009f00 f4009f04 c061ac4f
 Call Trace:
  [<c0205df6>] try_stack_unwind+0x156/0x170
  [<c020482a>] dump_trace+0x5a/0x1b0
  [<c0205e56>] show_trace_log_lvl+0x46/0x50
  [<c02049d1>] show_stack_log_lvl+0x51/0xe0
  [<c0205eb7>] show_stack+0x27/0x50
  [<c078deaf>] dump_stack+0x45/0x65
  [<c024c884>] warn_slowpath_common+0x84/0xa0
  [<c024c8d3>] warn_slowpath_fmt+0x33/0x40
  [<c061ac4f>] usb_submit_urb+0x5f/0x70
  [<f7974104>] snd_usbmidi_submit_urb+0x14/0x60 [snd_usbmidi_lib]
  [<f797483a>] snd_usbmidi_error_timer+0x6a/0xa0 [snd_usbmidi_lib]
  [<c02570c0>] call_timer_fn+0x30/0x130
  [<c0257442>] run_timer_softirq+0x1c2/0x260
  [<c0251493>] __do_softirq+0xc3/0x270
  [<c0204732>] do_softirq_own_stack+0x22/0x30
  [<c025186d>] irq_exit+0x8d/0xa0
  [<c0795228>] smp_apic_timer_interrupt+0x38/0x50
  [<c0794a3c>] apic_timer_interrupt+0x34/0x3c
  [<c0673d9e>] cpuidle_enter_state+0x3e/0xd0
  [<c028bb8d>] cpu_idle_loop+0x29d/0x3e0
  [<c028bd23>] cpu_startup_entry+0x53/0x60
  [<c0bfac1e>] start_kernel+0x415/0x41a

For avoiding these errors, check the pending URBs and skip
resubmitting such ones.

Reported-and-tested-by: Stefan Seyfried <stefan.seyfried@googlemail.com>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 sound/usb/midi.c |    2 ++
 1 file changed, 2 insertions(+)

--- a/sound/usb/midi.c
+++ b/sound/usb/midi.c
@@ -364,6 +364,8 @@ static void snd_usbmidi_error_timer(unsi
 		if (in && in->error_resubmit) {
 			in->error_resubmit = 0;
 			for (j = 0; j < INPUT_URBS; ++j) {
+				if (atomic_read(&in->urbs[j]->use_count))
+					continue;
 				in->urbs[j]->dev = umidi->dev;
 				snd_usbmidi_submit_urb(in->urbs[j], GFP_ATOMIC);
 			}

Re: [PATCH 3.14 00/34] 3.14.27-stable review

[Guenter Roeck]

On 12/14/2014 12:20 PM, Greg Kroah-Hartman wrote:
> This is the start of the stable review cycle for the 3.14.27 release.
> There are 34 patches in this series, all will be posted as a response
> to this one.  If anyone has any issues with these being applied, please
> let me know.
>
> Responses should be made by Tue Dec 16 20:17:55 UTC 2014.
> Anything received after that time might be too late.
>

Build results:
	total: 137 pass: 137 fail: 0

Qemu tests:
	total: 30 pass: 30 fail: 0

Details are available at http://server.roeck-us.net:8010/builders.

Guenter

Re: [PATCH 3.14 00/34] 3.14.27-stable review

[Shuah Khan]

On 12/14/2014 01:20 PM, Greg Kroah-Hartman wrote:
> This is the start of the stable review cycle for the 3.14.27 release.
> There are 34 patches in this series, all will be posted as a response
> to this one.  If anyone has any issues with these being applied, please
> let me know.
> 
> Responses should be made by Tue Dec 16 20:17:55 UTC 2014.
> Anything received after that time might be too late.
> 
> The whole patch series can be found in one patch at:
> 	kernel.org/pub/linux/kernel/v3.0/stable-review/patch-3.14.27-rc1.gz
> and the diffstat can be found below.
> 
> thanks,
> 
> greg k-h
> 

Compiled and booted on my test system. No dmesg regressions.

-- Shuah


-- 
Shuah Khan
Sr. Linux Kernel Developer
Samsung Open Source Group
Samsung Research America (Silicon Valley)
shuahkh@osg.samsung.com | (970) 217-8978