From: Chanwoo Choi <cw00.choi@samsung.com>
To: Robert Baldyga <r.baldyga@samsung.com>
Cc: myungjoo.ham@samsung.com, rogerq@ti.com,
linux-usb@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org, m.szyprowski@samsung.com
Subject: Re: [PATCH v3 2/4] extcon: usb-gpio: add support for VBUS detection
Date: Fri, 10 Apr 2015 16:17:36 +0900 [thread overview]
Message-ID: <55277910.2070000@samsung.com> (raw)
In-Reply-To: <55264534.4020006@samsung.com>
Hi Robert,
On 04/09/2015 06:24 PM, Robert Baldyga wrote:
> Hi Chanwoo,
>
> On 04/09/2015 11:07 AM, Chanwoo Choi wrote:
>> Hi Robert,
>>
>> On 04/09/2015 04:57 PM, Robert Baldyga wrote:
>>> Hi Chanwoo,
>>>
>>> On 04/09/2015 04:12 AM, Chanwoo Choi wrote:
>>>> Hi Robert,
>>>>
>>
>> [snip]
>>
>>>> But, I have one question about case[3]
>>>>
>>>> If id is low and vbus is high, this patch will update the state of both USB and USB-HOST cable as attached state.
>>>> Is it possible that two different cables (both USB and USB-HOST) are connected to one port simultaneously?
>>>>
>>>
>>> It's because state of single USB cable connection cannot be completely
>>> described using single extcon cable. USB cable state has two bits (VBUS
>>> and ID), so we need to use two cables for single cable connection. We
>>> use following convention:
>>> cable "USB" = VBUS
>>> cable "USB-HOST" = !ID.
>>
>> I think that extcon provider driver have to update the only one cable state
>> of either USB or USB-HOST because USB and USB-HOST feature can not be used
>> at the same time through one h/w port.
>>
>> If extcon-usb-gpio.c update two connected event of both USB and USB-HOST cable
>> at the same time, the extcon consumer driver can not decide what handle either USB or USB-HOST.
>>
>
> It can. USB OTG allows for that. Moreover device can be host even if
> ID=1 (so detected cable type is USB device), or peripheral when ID=0 (so
> detected cable type is USB host). Devices would need to have complete
> information about USB cable connection, because OTG state machine needs
As I knew, USB OTG port don't send the attached cable of both USB and USB-HOST
at the same time. The case3 in your patch update two cable state about one h/w port.
I don't agree.
> that. As I wrote, current USB cable names are misleading. It would be
> better to have "USB-VBUS" and "USB-ID".
It is strange cable name. I prefer to use only 'USB' cable name.
But, we could support the other method to get the state of whether USB-VBUS or USB-ID
by using helper API or others.
Thanks,
Chanwoo Choi
next prev parent reply other threads:[~2015-04-10 7:17 UTC|newest]
Thread overview: 39+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-04-02 13:13 [PATCH v3 0/4] extcon: usb-gpio: fixes and improvements Robert Baldyga
2015-04-02 13:13 ` [PATCH v3 1/4] extcon: usb-gpio: register extcon device before IRQ registration Robert Baldyga
2015-04-03 0:09 ` Chanwoo Choi
2015-04-02 13:13 ` [PATCH v3 2/4] extcon: usb-gpio: add support for VBUS detection Robert Baldyga
2015-04-02 14:02 ` Roger Quadros
2015-04-09 2:12 ` Chanwoo Choi
2015-04-09 7:57 ` Robert Baldyga
2015-04-09 9:07 ` Chanwoo Choi
2015-04-09 9:24 ` Robert Baldyga
2015-04-09 9:59 ` Roger Quadros
2015-04-09 10:18 ` Robert Baldyga
2015-04-10 7:39 ` Chanwoo Choi
2015-04-10 7:17 ` Chanwoo Choi [this message]
2015-04-10 7:45 ` Robert Baldyga
2015-04-10 8:10 ` Chanwoo Choi
2015-04-10 8:46 ` Robert Baldyga
2015-04-10 9:18 ` Chanwoo Choi
2015-04-10 9:42 ` Robert Baldyga
2015-04-14 10:01 ` Roger Quadros
2015-04-14 10:02 ` Roger Quadros
2015-04-14 10:31 ` Chanwoo Choi
2015-04-14 10:38 ` Roger Quadros
2015-04-14 11:29 ` Chanwoo Choi
2015-04-15 3:27 ` Peter Chen
2015-04-15 7:50 ` Roger Quadros
2015-04-15 9:26 ` Chanwoo Choi
2015-04-16 1:59 ` Peter Chen
2015-04-16 7:00 ` Chanwoo Choi
2015-04-16 7:13 ` Ivan T. Ivanov
2015-04-16 7:59 ` Chanwoo Choi
2015-04-16 8:01 ` Peter Chen
2015-04-16 8:26 ` Chanwoo Choi
2015-04-30 7:32 ` Roger Quadros
2015-04-30 7:55 ` Chanwoo Choi
2015-04-30 8:04 ` Roger Quadros
2015-04-16 7:59 ` Peter Chen
2015-04-16 7:16 ` Roger Quadros
2015-04-02 13:13 ` [PATCH v3 3/4] extcon: usb-gpio: make debounce value configurable in devicetree Robert Baldyga
2015-04-02 13:13 ` [PATCH v3 4/4] Documentation: extcon: usb-gpio: update usb-gpio binding description Robert Baldyga
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=55277910.2070000@samsung.com \
--to=cw00.choi@samsung.com \
--cc=devicetree@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-usb@vger.kernel.org \
--cc=m.szyprowski@samsung.com \
--cc=myungjoo.ham@samsung.com \
--cc=r.baldyga@samsung.com \
--cc=rogerq@ti.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).