[PATCH v2 0/9] Broadcom Cygnus device tree changes

[PATCH v2 0/9] Broadcom Cygnus device tree changes

[Ray Jui]

This patch series cleans up the Broadcom Cygnus device tree files and makes it
more consistent with the rest of Broadcom iProc device tree files. This patch
series also enables various peripherals on Cygnus boards. They include:

bcm11360_entphn:
NAND

bcm958300k:
touchscreen

bcm958305k:
I2C, PCIe, NAND, touchscreen

Code is based on v4.3-rc1 and is available on GITHUB:
https://github.com/Broadcom/cygnus-linux/tree/cygnus-dt-v2

Chages from V1:
- Break the major clean up change into separate patches

Ray Jui (9):
  ARM: dts: consolidate aliases for Cygnus dt files
  ARM: dts: Use label for device nodes in Cygnus dts
  ARM: dts: Remove unused PCI I/O resource in Cygnus
  ARM: dts: Put Cygnus core components under core bus
  ARM: dts: Move all Cygnus peripherals into soc bus
  ARM: dts: Reorder Cygnus peripherals
  ARM: dts: Enable various peripherals on bcm958305k
  ARM: dts: Enable NAND support on bcm911360_entphn
  ARM: dts: enable touchscreen support on Cygnus

 arch/arm/boot/dts/bcm-cygnus.dtsi      | 337 +++++++++++++++++----------------
 arch/arm/boot/dts/bcm911360_entphn.dts |  28 ++-
 arch/arm/boot/dts/bcm911360k.dts       |  10 +-
 arch/arm/boot/dts/bcm958300k.dts       |  45 ++---
 arch/arm/boot/dts/bcm958305k.dts       |  41 +++-
 arch/arm/boot/dts/bcm9hmidc.dtsi       |  42 ++++
 6 files changed, 299 insertions(+), 204 deletions(-)
 create mode 100644 arch/arm/boot/dts/bcm9hmidc.dtsi

-- 
1.9.1

[PATCH v2 1/9] ARM: dts: consolidate aliases for Cygnus dt files

[Ray Jui]

Move aliases into bcm-cygnus.dtsi to avoid duplications in Cygnus dts
files

Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
---
 arch/arm/boot/dts/bcm-cygnus.dtsi      | 4 ++++
 arch/arm/boot/dts/bcm911360_entphn.dts | 4 ----
 arch/arm/boot/dts/bcm911360k.dts       | 4 ----
 arch/arm/boot/dts/bcm958300k.dts       | 4 ----
 arch/arm/boot/dts/bcm958305k.dts       | 4 ----
 5 files changed, 4 insertions(+), 16 deletions(-)

diff --git a/arch/arm/boot/dts/bcm-cygnus.dtsi b/arch/arm/boot/dts/bcm-cygnus.dtsi
index e1ac07a..30903ba 100644
--- a/arch/arm/boot/dts/bcm-cygnus.dtsi
+++ b/arch/arm/boot/dts/bcm-cygnus.dtsi
@@ -40,6 +40,10 @@
 	model = "Broadcom Cygnus SoC";
 	interrupt-parent = <&gic>;
 
+	aliases {
+		serial0 = &uart3;
+	};
+
 	cpus {
 		#address-cells = <1>;
 		#size-cells = <0>;
diff --git a/arch/arm/boot/dts/bcm911360_entphn.dts b/arch/arm/boot/dts/bcm911360_entphn.dts
index 7db4843..0e1320e 100644
--- a/arch/arm/boot/dts/bcm911360_entphn.dts
+++ b/arch/arm/boot/dts/bcm911360_entphn.dts
@@ -39,10 +39,6 @@
 	model = "Cygnus Enterprise Phone (BCM911360_ENTPHN)";
 	compatible = "brcm,bcm11360", "brcm,cygnus";
 
-	aliases {
-		serial0 = &uart3;
-	};
-
 	chosen {
 		stdout-path = &uart3;
 		bootargs = "console=ttyS0,115200";
diff --git a/arch/arm/boot/dts/bcm911360k.dts b/arch/arm/boot/dts/bcm911360k.dts
index 9658d4f..2af40c6 100644
--- a/arch/arm/boot/dts/bcm911360k.dts
+++ b/arch/arm/boot/dts/bcm911360k.dts
@@ -38,10 +38,6 @@
 	model = "Cygnus SVK (BCM911360K)";
 	compatible = "brcm,bcm11360", "brcm,cygnus";
 
-	aliases {
-		serial0 = &uart3;
-	};
-
 	chosen {
 		stdout-path = &uart3;
 		bootargs = "console=ttyS0,115200";
diff --git a/arch/arm/boot/dts/bcm958300k.dts b/arch/arm/boot/dts/bcm958300k.dts
index 2f63052..75e50f0 100644
--- a/arch/arm/boot/dts/bcm958300k.dts
+++ b/arch/arm/boot/dts/bcm958300k.dts
@@ -38,10 +38,6 @@
 	model = "Cygnus SVK (BCM958300K)";
 	compatible = "brcm,bcm58300", "brcm,cygnus";
 
-	aliases {
-		serial0 = &uart3;
-	};
-
 	chosen {
 		stdout-path = &uart3;
 		bootargs = "console=ttyS0,115200";
diff --git a/arch/arm/boot/dts/bcm958305k.dts b/arch/arm/boot/dts/bcm958305k.dts
index 56b429a..bf62e1b 100644
--- a/arch/arm/boot/dts/bcm958305k.dts
+++ b/arch/arm/boot/dts/bcm958305k.dts
@@ -38,10 +38,6 @@
 	model = "Cygnus Wireless Audio (BCM958305K)";
 	compatible = "brcm,bcm58305", "brcm,cygnus";
 
-	aliases {
-		serial0 = &uart3;
-	};
-
 	chosen {
 		stdout-path = &uart3;
 		bootargs = "console=ttyS0,115200";
-- 
1.9.1

[PATCH v2 2/9] ARM: dts: Use label for device nodes in Cygnus dts

[Ray Jui]

Use label instead of full path to reference device nodes in Cygnus dts
files

Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
---
 arch/arm/boot/dts/bcm911360_entphn.dts |  8 +++----
 arch/arm/boot/dts/bcm911360k.dts       |  6 ++---
 arch/arm/boot/dts/bcm958300k.dts       | 40 +++++++++++++++++-----------------
 arch/arm/boot/dts/bcm958305k.dts       |  6 ++---
 4 files changed, 30 insertions(+), 30 deletions(-)

diff --git a/arch/arm/boot/dts/bcm911360_entphn.dts b/arch/arm/boot/dts/bcm911360_entphn.dts
index 0e1320e..f791a3b 100644
--- a/arch/arm/boot/dts/bcm911360_entphn.dts
+++ b/arch/arm/boot/dts/bcm911360_entphn.dts
@@ -44,10 +44,6 @@
 		bootargs = "console=ttyS0,115200";
 	};
 
-	uart3: serial@18023000 {
-		status = "okay";
-	};
-
 	gpio_keys {
 		compatible = "gpio-keys";
 		#address-cells = <1>;
@@ -60,3 +56,7 @@
 		};
 	};
 };
+
+&uart3 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/bcm911360k.dts b/arch/arm/boot/dts/bcm911360k.dts
index 2af40c6..814011c 100644
--- a/arch/arm/boot/dts/bcm911360k.dts
+++ b/arch/arm/boot/dts/bcm911360k.dts
@@ -42,8 +42,8 @@
 		stdout-path = &uart3;
 		bootargs = "console=ttyS0,115200";
 	};
+};
 
-	uart3: serial@18023000 {
-		status = "okay";
-	};
+&uart3 {
+	status = "okay";
 };
diff --git a/arch/arm/boot/dts/bcm958300k.dts b/arch/arm/boot/dts/bcm958300k.dts
index 75e50f0..d8dc9f0 100644
--- a/arch/arm/boot/dts/bcm958300k.dts
+++ b/arch/arm/boot/dts/bcm958300k.dts
@@ -42,32 +42,32 @@
 		stdout-path = &uart3;
 		bootargs = "console=ttyS0,115200";
 	};
+};
 
-	pcie0: pcie@18012000 {
-		status = "okay";
-	};
+&pcie0 {
+	status = "okay";
+};
 
-	pcie1: pcie@18013000 {
-		status = "okay";
-	};
+&pcie1 {
+	status = "okay";
+};
 
-	uart3: serial@18023000 {
-		status = "okay";
-	};
+&uart3 {
+	status = "okay";
+};
 
-	nand: nand@18046000 {
-		nandcs@1 {
-			compatible = "brcm,nandcs";
-			reg = <0>;
-			nand-on-flash-bbt;
+&nand {
+	nandcs@1 {
+		compatible = "brcm,nandcs";
+		reg = <0>;
+		nand-on-flash-bbt;
 
-			#address-cells = <1>;
-			#size-cells = <1>;
+		#address-cells = <1>;
+		#size-cells = <1>;
 
-			nand-ecc-strength = <24>;
-			nand-ecc-step-size = <1024>;
+		nand-ecc-strength = <24>;
+		nand-ecc-step-size = <1024>;
 
-			brcm,nand-oob-sector-size = <27>;
-		};
+		brcm,nand-oob-sector-size = <27>;
 	};
 };
diff --git a/arch/arm/boot/dts/bcm958305k.dts b/arch/arm/boot/dts/bcm958305k.dts
index bf62e1b..af11a8e 100644
--- a/arch/arm/boot/dts/bcm958305k.dts
+++ b/arch/arm/boot/dts/bcm958305k.dts
@@ -42,8 +42,8 @@
 		stdout-path = &uart3;
 		bootargs = "console=ttyS0,115200";
 	};
+};
 
-	uart3: serial@18023000 {
-		status = "okay";
-	};
+&uart3 {
+	status = "okay";
 };
-- 
1.9.1

[PATCH v2 3/9] ARM: dts: Remove unused PCI I/O resource in Cygnus

[Ray Jui]

Remove unused PCI I/O resource in bcm-cygnus.dtsi

Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
---
 arch/arm/boot/dts/bcm-cygnus.dtsi | 6 ++----
 1 file changed, 2 insertions(+), 4 deletions(-)

diff --git a/arch/arm/boot/dts/bcm-cygnus.dtsi b/arch/arm/boot/dts/bcm-cygnus.dtsi
index 30903ba..0a5898b 100644
--- a/arch/arm/boot/dts/bcm-cygnus.dtsi
+++ b/arch/arm/boot/dts/bcm-cygnus.dtsi
@@ -145,8 +145,7 @@
 		#address-cells = <3>;
 		#size-cells = <2>;
 		device_type = "pci";
-		ranges = <0x81000000 0 0	  0x28000000 0 0x00010000
-			  0x82000000 0 0x20000000 0x20000000 0 0x04000000>;
+		ranges = <0x82000000 0 0x20000000 0x20000000 0 0x04000000>;
 
 		status = "disabled";
 	};
@@ -166,8 +165,7 @@
 		#address-cells = <3>;
 		#size-cells = <2>;
 		device_type = "pci";
-		ranges = <0x81000000 0 0	  0x48000000 0 0x00010000
-			  0x82000000 0 0x40000000 0x40000000 0 0x04000000>;
+		ranges = <0x82000000 0 0x40000000 0x40000000 0 0x04000000>;
 
 		status = "disabled";
 	};
-- 
1.9.1

[PATCH v2 4/9] ARM: dts: Put Cygnus core components under core bus

[Ray Jui]

Put all Cygnus core components into "core" node of type "simple-bus" in
bcm-cygnus.dtsi

Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
---
 arch/arm/boot/dts/bcm-cygnus.dtsi | 54 ++++++++++++++++++++++-----------------
 1 file changed, 30 insertions(+), 24 deletions(-)

diff --git a/arch/arm/boot/dts/bcm-cygnus.dtsi b/arch/arm/boot/dts/bcm-cygnus.dtsi
index 0a5898b..d4e2d04 100644
--- a/arch/arm/boot/dts/bcm-cygnus.dtsi
+++ b/arch/arm/boot/dts/bcm-cygnus.dtsi
@@ -58,6 +58,36 @@
 
 	/include/ "bcm-cygnus-clock.dtsi"
 
+	core {
+		compatible = "simple-bus";
+		ranges;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		timer@19020200 {
+			compatible = "arm,cortex-a9-global-timer";
+			reg = <0x19020200 0x100>;
+			interrupts = <GIC_PPI 11 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&periph_clk>;
+		};
+
+		gic: interrupt-controller@19021000 {
+			compatible = "arm,cortex-a9-gic";
+			#interrupt-cells = <3>;
+			#address-cells = <0>;
+			interrupt-controller;
+			reg = <0x19021000 0x1000>,
+			      <0x19020100 0x100>;
+		};
+
+		L2: l2-cache {
+			compatible = "arm,pl310-cache";
+			reg = <0x19022000 0x1000>;
+			cache-unified;
+			cache-level = <2>;
+		};
+	};
+
 	pinctrl: pinctrl@0x0301d0c8 {
 		compatible = "brcm,cygnus-pinmux";
 		reg = <0x0301d0c8 0x30>,
@@ -225,28 +255,4 @@
 
 		brcm,nand-has-wp;
 	};
-
-	gic: interrupt-controller@19021000 {
-		compatible = "arm,cortex-a9-gic";
-		#interrupt-cells = <3>;
-		#address-cells = <0>;
-		interrupt-controller;
-		reg = <0x19021000 0x1000>,
-		      <0x19020100 0x100>;
-	};
-
-	L2: l2-cache {
-		compatible = "arm,pl310-cache";
-		reg = <0x19022000 0x1000>;
-		cache-unified;
-		cache-level = <2>;
-	};
-
-	timer@19020200 {
-		compatible = "arm,cortex-a9-global-timer";
-		reg = <0x19020200 0x100>;
-		interrupts = <GIC_PPI 11 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&periph_clk>;
-	};
-
 };
-- 
1.9.1

[PATCH v2 5/9] ARM: dts: Move all Cygnus peripherals into soc bus

[Ray Jui]

Move all Cygnus peripherals to be under the "soc" bus node of type
"simple-bus"

Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
---
 arch/arm/boot/dts/bcm-cygnus.dtsi | 275 +++++++++++++++++++-------------------
 1 file changed, 138 insertions(+), 137 deletions(-)

diff --git a/arch/arm/boot/dts/bcm-cygnus.dtsi b/arch/arm/boot/dts/bcm-cygnus.dtsi
index d4e2d04..3d29b77 100644
--- a/arch/arm/boot/dts/bcm-cygnus.dtsi
+++ b/arch/arm/boot/dts/bcm-cygnus.dtsi
@@ -88,171 +88,172 @@
 		};
 	};
 
-	pinctrl: pinctrl@0x0301d0c8 {
-		compatible = "brcm,cygnus-pinmux";
-		reg = <0x0301d0c8 0x30>,
-		      <0x0301d24c 0x2c>;
-	};
+	soc {
+		compatible = "simple-bus";
+		ranges;
+		#address-cells = <1>;
+		#size-cells = <1>;
 
-	gpio_crmu: gpio@03024800 {
-		compatible = "brcm,cygnus-crmu-gpio";
-		reg = <0x03024800 0x50>,
-		      <0x03024008 0x18>;
-		#gpio-cells = <2>;
-		gpio-controller;
-	};
+		pinctrl: pinctrl@0301d0c8 {
+			compatible = "brcm,cygnus-pinmux";
+			reg = <0x0301d0c8 0x30>,
+			      <0x0301d24c 0x2c>;
+		};
 
-	gpio_ccm: gpio@1800a000 {
-		compatible = "brcm,cygnus-ccm-gpio";
-		reg = <0x1800a000 0x50>,
-		      <0x0301d164 0x20>;
-		#gpio-cells = <2>;
-		gpio-controller;
-		interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
-		interrupt-controller;
-	};
+		gpio_crmu: gpio@03024800 {
+			compatible = "brcm,cygnus-crmu-gpio";
+			reg = <0x03024800 0x50>,
+			      <0x03024008 0x18>;
+			#gpio-cells = <2>;
+			gpio-controller;
+		};
 
-	gpio_asiu: gpio@180a5000 {
-		compatible = "brcm,cygnus-asiu-gpio";
-		reg = <0x180a5000 0x668>;
-		#gpio-cells = <2>;
-		gpio-controller;
+		gpio_ccm: gpio@1800a000 {
+			compatible = "brcm,cygnus-ccm-gpio";
+			reg = <0x1800a000 0x50>,
+			      <0x0301d164 0x20>;
+			#gpio-cells = <2>;
+			gpio-controller;
+			interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
+		};
 
-		pinmux = <&pinctrl>;
+		gpio_asiu: gpio@180a5000 {
+			compatible = "brcm,cygnus-asiu-gpio";
+			reg = <0x180a5000 0x668>;
+			#gpio-cells = <2>;
+			gpio-controller;
 
-		interrupt-controller;
-		interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>;
-	};
+			pinmux = <&pinctrl>;
 
-	amba {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		compatible = "arm,amba-bus", "simple-bus";
-		interrupt-parent = <&gic>;
-		ranges;
+			interrupt-controller;
+			interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>;
+		};
 
-		wdt@18009000 {
-			 compatible = "arm,sp805" , "arm,primecell";
-			 reg = <0x18009000 0x1000>;
-			 interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
-			 clocks = <&axi81_clk>;
-			 clock-names = "apb_pclk";
+		wdt0: wdt@18009000 {
+			compatible = "arm,sp805" , "arm,primecell";
+			reg = <0x18009000 0x1000>;
+			interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&axi81_clk>;
+			clock-names = "apb_pclk";
 		};
-	};
 
-	i2c0: i2c@18008000 {
-		compatible = "brcm,cygnus-iproc-i2c", "brcm,iproc-i2c";
-		reg = <0x18008000 0x100>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-		interrupts = <GIC_SPI 85 IRQ_TYPE_NONE>;
-		clock-frequency = <100000>;
-		status = "disabled";
-	};
+		i2c0: i2c@18008000 {
+			compatible = "brcm,cygnus-iproc-i2c", "brcm,iproc-i2c";
+			reg = <0x18008000 0x100>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <GIC_SPI 85 IRQ_TYPE_NONE>;
+			clock-frequency = <100000>;
+			status = "disabled";
+		};
 
-	i2c1: i2c@1800b000 {
-		compatible = "brcm,cygnus-iproc-i2c", "brcm,iproc-i2c";
-		reg = <0x1800b000 0x100>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-		interrupts = <GIC_SPI 86 IRQ_TYPE_NONE>;
-		clock-frequency = <100000>;
-		status = "disabled";
-	};
+		i2c1: i2c@1800b000 {
+			compatible = "brcm,cygnus-iproc-i2c", "brcm,iproc-i2c";
+			reg = <0x1800b000 0x100>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <GIC_SPI 86 IRQ_TYPE_NONE>;
+			clock-frequency = <100000>;
+			status = "disabled";
+		};
 
-	pcie0: pcie@18012000 {
-		compatible = "brcm,iproc-pcie";
-		reg = <0x18012000 0x1000>;
+		pcie0: pcie@18012000 {
+			compatible = "brcm,iproc-pcie";
+			reg = <0x18012000 0x1000>;
 
-		#interrupt-cells = <1>;
-		interrupt-map-mask = <0 0 0 0>;
-		interrupt-map = <0 0 0 0 &gic GIC_SPI 100 IRQ_TYPE_NONE>;
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0>;
+			interrupt-map = <0 0 0 0 &gic GIC_SPI 100 IRQ_TYPE_NONE>;
 
-		linux,pci-domain = <0>;
+			linux,pci-domain = <0>;
 
-		bus-range = <0x00 0xff>;
+			bus-range = <0x00 0xff>;
 
-		#address-cells = <3>;
-		#size-cells = <2>;
-		device_type = "pci";
-		ranges = <0x82000000 0 0x20000000 0x20000000 0 0x04000000>;
+			#address-cells = <3>;
+			#size-cells = <2>;
+			device_type = "pci";
+			ranges = <0x82000000 0 0x20000000 0x20000000 0 0x04000000>;
 
-		status = "disabled";
-	};
+			status = "disabled";
+		};
 
-	pcie1: pcie@18013000 {
-		compatible = "brcm,iproc-pcie";
-		reg = <0x18013000 0x1000>;
+		pcie1: pcie@18013000 {
+			compatible = "brcm,iproc-pcie";
+			reg = <0x18013000 0x1000>;
 
-		#interrupt-cells = <1>;
-		interrupt-map-mask = <0 0 0 0>;
-		interrupt-map = <0 0 0 0 &gic GIC_SPI 106 IRQ_TYPE_NONE>;
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0>;
+			interrupt-map = <0 0 0 0 &gic GIC_SPI 106 IRQ_TYPE_NONE>;
 
-		linux,pci-domain = <1>;
+			linux,pci-domain = <1>;
 
-		bus-range = <0x00 0xff>;
+			bus-range = <0x00 0xff>;
 
-		#address-cells = <3>;
-		#size-cells = <2>;
-		device_type = "pci";
-		ranges = <0x82000000 0 0x40000000 0x40000000 0 0x04000000>;
+			#address-cells = <3>;
+			#size-cells = <2>;
+			device_type = "pci";
+			ranges = <0x82000000 0 0x40000000 0x40000000 0 0x04000000>;
 
-		status = "disabled";
-	};
+			status = "disabled";
+		};
 
-	uart0: serial@18020000 {
-		compatible = "snps,dw-apb-uart";
-		reg = <0x18020000 0x100>;
-		reg-shift = <2>;
-		reg-io-width = <4>;
-		interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&axi81_clk>;
-		clock-frequency = <100000000>;
-		status = "disabled";
-	};
+		uart0: serial@18020000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x18020000 0x100>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&axi81_clk>;
+			clock-frequency = <100000000>;
+			status = "disabled";
+		};
 
-	uart1: serial@18021000 {
-		compatible = "snps,dw-apb-uart";
-		reg = <0x18021000 0x100>;
-		reg-shift = <2>;
-		reg-io-width = <4>;
-		interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&axi81_clk>;
-		clock-frequency = <100000000>;
-		status = "disabled";
-	};
+		uart1: serial@18021000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x18021000 0x100>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&axi81_clk>;
+			clock-frequency = <100000000>;
+			status = "disabled";
+		};
 
-	uart2: serial@18022000 {
-		compatible = "snps,dw-apb-uart";
-		reg = <0x18020000 0x100>;
-		reg-shift = <2>;
-		reg-io-width = <4>;
-		interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&axi81_clk>;
-		clock-frequency = <100000000>;
-		status = "disabled";
-	};
+		uart2: serial@18022000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x18020000 0x100>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&axi81_clk>;
+			clock-frequency = <100000000>;
+			status = "disabled";
+		};
 
-	uart3: serial@18023000 {
-		compatible = "snps,dw-apb-uart";
-		reg = <0x18023000 0x100>;
-		reg-shift = <2>;
-		reg-io-width = <4>;
-		interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&axi81_clk>;
-		clock-frequency = <100000000>;
-		status = "disabled";
-	};
+		uart3: serial@18023000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x18023000 0x100>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&axi81_clk>;
+			clock-frequency = <100000000>;
+			status = "disabled";
+		};
 
-	nand: nand@18046000 {
-		compatible = "brcm,nand-iproc", "brcm,brcmnand-v6.1", "brcm,brcmnand";
-		reg = <0x18046000 0x600>, <0xf8105408 0x600>, <0x18046f00 0x20>;
-		reg-names = "nand", "iproc-idm", "iproc-ext";
-		interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
+		nand: nand@18046000 {
+			compatible = "brcm,nand-iproc", "brcm,brcmnand-v6.1",
+				     "brcm,brcmnand";
+			reg = <0x18046000 0x600>, <0xf8105408 0x600>,
+			      <0x18046f00 0x20>;
+			reg-names = "nand", "iproc-idm", "iproc-ext";
+			interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
 
-		#address-cells = <1>;
-		#size-cells = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
 
-		brcm,nand-has-wp;
+			brcm,nand-has-wp;
+		};
 	};
 };
-- 
1.9.1

[PATCH v2 6/9] ARM: dts: Reorder Cygnus peripherals

[Ray Jui]

Reorder all Cygnus peripherals based on base register addresses in
bcm-cygnus.dtsi

Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
---
 arch/arm/boot/dts/bcm-cygnus.dtsi | 56 +++++++++++++++++++--------------------
 1 file changed, 28 insertions(+), 28 deletions(-)

diff --git a/arch/arm/boot/dts/bcm-cygnus.dtsi b/arch/arm/boot/dts/bcm-cygnus.dtsi
index 3d29b77..dfa9a3c 100644
--- a/arch/arm/boot/dts/bcm-cygnus.dtsi
+++ b/arch/arm/boot/dts/bcm-cygnus.dtsi
@@ -108,26 +108,14 @@
 			gpio-controller;
 		};
 
-		gpio_ccm: gpio@1800a000 {
-			compatible = "brcm,cygnus-ccm-gpio";
-			reg = <0x1800a000 0x50>,
-			      <0x0301d164 0x20>;
-			#gpio-cells = <2>;
-			gpio-controller;
-			interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-controller;
-		};
-
-		gpio_asiu: gpio@180a5000 {
-			compatible = "brcm,cygnus-asiu-gpio";
-			reg = <0x180a5000 0x668>;
-			#gpio-cells = <2>;
-			gpio-controller;
-
-			pinmux = <&pinctrl>;
-
-			interrupt-controller;
-			interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>;
+		i2c0: i2c@18008000 {
+			compatible = "brcm,cygnus-iproc-i2c", "brcm,iproc-i2c";
+			reg = <0x18008000 0x100>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <GIC_SPI 85 IRQ_TYPE_NONE>;
+			clock-frequency = <100000>;
+			status = "disabled";
 		};
 
 		wdt0: wdt@18009000 {
@@ -138,14 +126,14 @@
 			clock-names = "apb_pclk";
 		};
 
-		i2c0: i2c@18008000 {
-			compatible = "brcm,cygnus-iproc-i2c", "brcm,iproc-i2c";
-			reg = <0x18008000 0x100>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-			interrupts = <GIC_SPI 85 IRQ_TYPE_NONE>;
-			clock-frequency = <100000>;
-			status = "disabled";
+		gpio_ccm: gpio@1800a000 {
+			compatible = "brcm,cygnus-ccm-gpio";
+			reg = <0x1800a000 0x50>,
+			      <0x0301d164 0x20>;
+			#gpio-cells = <2>;
+			gpio-controller;
+			interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
 		};
 
 		i2c1: i2c@1800b000 {
@@ -255,5 +243,17 @@
 
 			brcm,nand-has-wp;
 		};
+
+		gpio_asiu: gpio@180a5000 {
+			compatible = "brcm,cygnus-asiu-gpio";
+			reg = <0x180a5000 0x668>;
+			#gpio-cells = <2>;
+			gpio-controller;
+
+			pinmux = <&pinctrl>;
+
+			interrupt-controller;
+			interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>;
+		};
 	};
 };
-- 
1.9.1

[PATCH v2 7/9] ARM: dts: Enable various peripherals on bcm958305k

[Ray Jui]

This patch enables various peripherals on Broadcom Cygnus wireless audio
board (bcm958305k). These peripherals include I2C, PCIe, and NAND

Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
---
 arch/arm/boot/dts/bcm958305k.dts | 32 ++++++++++++++++++++++++++++++++
 1 file changed, 32 insertions(+)

diff --git a/arch/arm/boot/dts/bcm958305k.dts b/arch/arm/boot/dts/bcm958305k.dts
index af11a8e..9863a19 100644
--- a/arch/arm/boot/dts/bcm958305k.dts
+++ b/arch/arm/boot/dts/bcm958305k.dts
@@ -44,6 +44,38 @@
 	};
 };
 
+&i2c0 {
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&pcie0 {
+	status = "okay";
+};
+
+&pcie1 {
+	status = "okay";
+};
+
 &uart3 {
 	status = "okay";
 };
+
+&nand {
+	nandcs@1 {
+		compatible = "brcm,nandcs";
+		reg = <0>;
+		nand-on-flash-bbt;
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		nand-ecc-strength = <24>;
+		nand-ecc-step-size = <1024>;
+
+		brcm,nand-oob-sector-size = <27>;
+	};
+};
-- 
1.9.1

[PATCH v2 8/9] ARM: dts: Enable NAND support on bcm911360_entphn

[Ray Jui]

This patch enables NAND support on Broadcom Cygnus form factor board
(bcm911360_entphn)

Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
---
 arch/arm/boot/dts/bcm911360_entphn.dts | 16 ++++++++++++++++
 1 file changed, 16 insertions(+)

diff --git a/arch/arm/boot/dts/bcm911360_entphn.dts b/arch/arm/boot/dts/bcm911360_entphn.dts
index f791a3b..8b3800f 100644
--- a/arch/arm/boot/dts/bcm911360_entphn.dts
+++ b/arch/arm/boot/dts/bcm911360_entphn.dts
@@ -60,3 +60,19 @@
 &uart3 {
 	status = "okay";
 };
+
+&nand {
+	nandcs@1 {
+		compatible = "brcm,nandcs";
+		reg = <0>;
+		nand-on-flash-bbt;
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		nand-ecc-strength = <24>;
+		nand-ecc-step-size = <1024>;
+
+		brcm,nand-oob-sector-size = <27>;
+	};
+};
-- 
1.9.1

[PATCH v2 9/9] ARM: dts: enable touchscreen support on Cygnus

[Ray Jui]

This patch enables touchscreen support on bcm958300k and bcm958305k.
Touchscreen is connected to these boards through the bcm9hmidc daughter
card, and therefore also adding bcm9hmidc.dtsi that describes the
daughter card

Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Vikram Prakash <vikramp@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
---
 arch/arm/boot/dts/bcm-cygnus.dtsi | 10 ++++++++++
 arch/arm/boot/dts/bcm958300k.dts  |  1 +
 arch/arm/boot/dts/bcm958305k.dts  |  1 +
 arch/arm/boot/dts/bcm9hmidc.dtsi  | 42 +++++++++++++++++++++++++++++++++++++++
 4 files changed, 54 insertions(+)
 create mode 100644 arch/arm/boot/dts/bcm9hmidc.dtsi

diff --git a/arch/arm/boot/dts/bcm-cygnus.dtsi b/arch/arm/boot/dts/bcm-cygnus.dtsi
index dfa9a3c..d898838 100644
--- a/arch/arm/boot/dts/bcm-cygnus.dtsi
+++ b/arch/arm/boot/dts/bcm-cygnus.dtsi
@@ -32,6 +32,7 @@
 
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/clock/bcm-cygnus.h>
 
 #include "skeleton.dtsi"
 
@@ -255,5 +256,14 @@
 			interrupt-controller;
 			interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>;
 		};
+
+		touchscreen: tsc@180a6000 {
+			compatible = "brcm,iproc-touchscreen";
+			reg = <0x180a6000 0x40>;
+			clocks = <&asiu_clks BCM_CYGNUS_ASIU_ADC_CLK>;
+			clock-names = "tsc_clk";
+			interrupts = <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
 	};
 };
diff --git a/arch/arm/boot/dts/bcm958300k.dts b/arch/arm/boot/dts/bcm958300k.dts
index d8dc9f0..2e31581 100644
--- a/arch/arm/boot/dts/bcm958300k.dts
+++ b/arch/arm/boot/dts/bcm958300k.dts
@@ -33,6 +33,7 @@
 /dts-v1/;
 
 #include "bcm-cygnus.dtsi"
+#include "bcm9hmidc.dtsi"
 
 / {
 	model = "Cygnus SVK (BCM958300K)";
diff --git a/arch/arm/boot/dts/bcm958305k.dts b/arch/arm/boot/dts/bcm958305k.dts
index 9863a19..288a637 100644
--- a/arch/arm/boot/dts/bcm958305k.dts
+++ b/arch/arm/boot/dts/bcm958305k.dts
@@ -33,6 +33,7 @@
 /dts-v1/;
 
 #include "bcm-cygnus.dtsi"
+#include "bcm9hmidc.dtsi"
 
 / {
 	model = "Cygnus Wireless Audio (BCM958305K)";
diff --git a/arch/arm/boot/dts/bcm9hmidc.dtsi b/arch/arm/boot/dts/bcm9hmidc.dtsi
new file mode 100644
index 0000000..65397c0
--- /dev/null
+++ b/arch/arm/boot/dts/bcm9hmidc.dtsi
@@ -0,0 +1,42 @@
+/*
+ *  BSD LICENSE
+ *
+ *  Copyright(c) 2015 Broadcom Corporation.  All rights reserved.
+ *
+ *  Redistribution and use in source and binary forms, with or without
+ *  modification, are permitted provided that the following conditions
+ *  are met:
+ *
+ *    * Redistributions of source code must retain the above copyright
+ *      notice, this list of conditions and the following disclaimer.
+ *    * Redistributions in binary form must reproduce the above copyright
+ *      notice, this list of conditions and the following disclaimer in
+ *      the documentation and/or other materials provided with the
+ *      distribution.
+ *    * Neither the name of Broadcom Corporation nor the names of its
+ *      contributors may be used to endorse or promote products derived
+ *      from this software without specific prior written permission.
+ *
+ *  THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ *  "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ *  LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+ *  A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ *  OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+ *  SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ *  LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+ *  DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+ *  THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/*
+ * Broadcom human machine interface daughter card (bcm9hmidc) installed on
+ * bcm958300k/bcm958305k boards
+ */
+
+&touchscreen {
+	touchscreen-inverted-x;
+	touchscreen-inverted-y;
+	status = "okay";
+};
-- 
1.9.1

Re: [PATCH v2 1/9] ARM: dts: consolidate aliases for Cygnus dt files

[Arnd Bergmann]

On Friday 18 September 2015 14:24:06 Ray Jui wrote:
> Move aliases into bcm-cygnus.dtsi to avoid duplications in Cygnus dts
> files
> 

We generally recommend keeping them separate:

> diff --git a/arch/arm/boot/dts/bcm-cygnus.dtsi b/arch/arm/boot/dts/bcm-cygnus.dtsi
> index e1ac07a..30903ba 100644
> --- a/arch/arm/boot/dts/bcm-cygnus.dtsi
> +++ b/arch/arm/boot/dts/bcm-cygnus.dtsi
> @@ -40,6 +40,10 @@
>         model = "Broadcom Cygnus SoC";
>         interrupt-parent = <&gic>;
>  
> +       aliases {
> +               serial0 = &uart3;
> +       };
> +

The SoC has at least four uarts according to this, so it seems unlikely that
each board really only uses only the fourth one of them and labels it '0'
on the board. As soon as you get one board that has more than one uart wired
up, you would need to undo this.

	Arnd

Re: [PATCH v2 3/9] ARM: dts: Remove unused PCI I/O resource in Cygnus

[Arnd Bergmann]

On Friday 18 September 2015 14:24:08 Ray Jui wrote:
> Remove unused PCI I/O resource in bcm-cygnus.dtsi
> 
> Signed-off-by: Ray Jui <rjui@broadcom.com>
> Reviewed-by: Scott Branden <sbranden@broadcom.com>
> 

Why? How do you know that nobody ever plugs in a card with I/O ports?

	Arnd

Re: [PATCH v2 4/9] ARM: dts: Put Cygnus core components under core bus

[Arnd Bergmann]

On Friday 18 September 2015 14:24:09 Ray Jui wrote:
> 
> +       core {
> +               compatible = "simple-bus";
> +               ranges;
> +               #address-cells = <1>;
> +               #size-cells = <1>;
> +
> +               timer@19020200 {
> +                       compatible = "arm,cortex-a9-global-timer";
> +                       reg = <0x19020200 0x100>;
> +                       interrupts = <GIC_PPI 11 IRQ_TYPE_LEVEL_HIGH>;
> +                       clocks = <&periph_clk>;
> +               };
> +
> +               gic: interrupt-controller@19021000 {
> 

Could it be that all 'core' components are in the 0x19xxxxxx address range?
If so, please set up an appropriate ranges property for the bus. Also
add the address field for the bus according to which addresses are routed
to it.

	Arnd

Re: [PATCH v2 5/9] ARM: dts: Move all Cygnus peripherals into soc bus

[Arnd Bergmann]

On Friday 18 September 2015 14:24:10 Ray Jui wrote:
> +       soc {
> +               compatible = "simple-bus";
> +               ranges;
> +               #address-cells = <1>;
> +               #size-cells = <1>;

> +               pinctrl: pinctrl@0301d0c8 {
> 

Similarly to the core bus, this seems to have address ranges 0x03xxxxxx and
0x18xxxxxx on it, so put those into the ranges.

It probably also makes sense to name the bus according to what kind of
bus (axi, ahb, plb, ...) is used here. If the soc has nested buses
(e.g. an ahb connected to an axi bus,) then model both of them in the DT.

	Arnd

Re: [PATCH v2 1/9] ARM: dts: consolidate aliases for Cygnus dt files

[Ray Jui]

On 9/18/2015 2:27 PM, Arnd Bergmann wrote:
> On Friday 18 September 2015 14:24:06 Ray Jui wrote:
>> Move aliases into bcm-cygnus.dtsi to avoid duplications in Cygnus dts
>> files
>>
> 
> We generally recommend keeping them separate:
> 
>> diff --git a/arch/arm/boot/dts/bcm-cygnus.dtsi b/arch/arm/boot/dts/bcm-cygnus.dtsi
>> index e1ac07a..30903ba 100644
>> --- a/arch/arm/boot/dts/bcm-cygnus.dtsi
>> +++ b/arch/arm/boot/dts/bcm-cygnus.dtsi
>> @@ -40,6 +40,10 @@
>>         model = "Broadcom Cygnus SoC";
>>         interrupt-parent = <&gic>;
>>  
>> +       aliases {
>> +               serial0 = &uart3;
>> +       };
>> +
> 
> The SoC has at least four uarts according to this, so it seems unlikely that
> each board really only uses only the fourth one of them and labels it '0'
> on the board. As soon as you get one board that has more than one uart wired
> up, you would need to undo this.
> 
> 	Arnd
> 

I think Scott might have explained this in the past. uart3 is going to
be used on all Cygnus boards (including all future boards) because the
bootrom was designed to use uart3 as console and that won't change.

Let me know if you still think I need to move this back to the dts.

Thanks,

Ray

Re: [PATCH v2 3/9] ARM: dts: Remove unused PCI I/O resource in Cygnus

[Ray Jui]

On 9/18/2015 2:28 PM, Arnd Bergmann wrote:
> On Friday 18 September 2015 14:24:08 Ray Jui wrote:
>> Remove unused PCI I/O resource in bcm-cygnus.dtsi
>>
>> Signed-off-by: Ray Jui <rjui@broadcom.com>
>> Reviewed-by: Scott Branden <sbranden@broadcom.com>
>>
> 
> Why? How do you know that nobody ever plugs in a card with I/O ports?
> 
> 	Arnd
> 

I'll drop this change.

Thanks,

Ray

Re: [PATCH v2 4/9] ARM: dts: Put Cygnus core components under core bus

[Ray Jui]

On 9/18/2015 2:30 PM, Arnd Bergmann wrote:
> On Friday 18 September 2015 14:24:09 Ray Jui wrote:
>>
>> +       core {
>> +               compatible = "simple-bus";
>> +               ranges;
>> +               #address-cells = <1>;
>> +               #size-cells = <1>;
>> +
>> +               timer@19020200 {
>> +                       compatible = "arm,cortex-a9-global-timer";
>> +                       reg = <0x19020200 0x100>;
>> +                       interrupts = <GIC_PPI 11 IRQ_TYPE_LEVEL_HIGH>;
>> +                       clocks = <&periph_clk>;
>> +               };
>> +
>> +               gic: interrupt-controller@19021000 {
>>
> 
> Could it be that all 'core' components are in the 0x19xxxxxx address range?
> If so, please set up an appropriate ranges property for the bus. Also
> add the address field for the bus according to which addresses are routed
> to it.
> 
> 	Arnd
> 

Yes all 'core' components are in the 0x19xxxxx address range for Cygnus.
It's fine and makes sense to set up proper ranges for this bus. But I
might have some issues with the 'soc' components and the 'soc' bus,
which I'll explain and discuss on the next email.

Ray

Re: [PATCH v2 5/9] ARM: dts: Move all Cygnus peripherals into soc bus

[Ray Jui]

On 9/18/2015 2:34 PM, Arnd Bergmann wrote:
> On Friday 18 September 2015 14:24:10 Ray Jui wrote:
>> +       soc {
>> +               compatible = "simple-bus";
>> +               ranges;
>> +               #address-cells = <1>;
>> +               #size-cells = <1>;
> 
>> +               pinctrl: pinctrl@0301d0c8 {
>>
> 
> Similarly to the core bus, this seems to have address ranges 0x03xxxxxx and
> 0x18xxxxxx on it, so put those into the ranges.
>

Okay we have an issue here. For whatever reason, the Cygnus ASIC team
decided to put registers for the same block in random locations. We see
similar issues in all of our other iProc based SoCs. We have
communicated this to our ASIC team, and hopefully they can revert the
trend for the next SoC.

For example, the gpio_ccm has registers in the following regions:

gpio_ccm: gpio@1800a000 {
    compatible = "brcm,cygnus-ccm-gpio";
    reg = <0x1800a000 0x50>,
          <0x0301d164 0x20>;

NAND is worse, it has registers in 3 different separate regions:

nand: nand@18046000 {
    compatible = "brcm,nand-iproc", "brcm,brcmnand-v6.1",
                 "brcm,brcmnand";
    reg = <0x18046000 0x600>, <0xf8105408 0x600>,
          <0x18046f00 0x20>;

As you can see, this makes it impossible to define a proper address
range for the bus; therefore, I'll have to keep the ranges undefined and
a simple 1:1 mapping under this bus.

> It probably also makes sense to name the bus according to what kind of
> bus (axi, ahb, plb, ...) is used here. If the soc has nested buses
> (e.g. an ahb connected to an axi bus,) then model both of them in the DT.

Based on the block diagram from the ASIC team, it looks like all of them
are connected to one major AXI fabric. I can rename the bus to AXI.

> 
> 	Arnd
> 

Thanks,

Ray

Re: [PATCH v2 5/9] ARM: dts: Move all Cygnus peripherals into soc bus

[Arnd Bergmann]

On Friday 18 September 2015 15:11:27 Ray Jui wrote:
> On 9/18/2015 2:34 PM, Arnd Bergmann wrote:
> > On Friday 18 September 2015 14:24:10 Ray Jui wrote:
> >> +       soc {
> >> +               compatible = "simple-bus";
> >> +               ranges;
> >> +               #address-cells = <1>;
> >> +               #size-cells = <1>;
> > 
> >> +               pinctrl: pinctrl@0301d0c8 {
> >>
> > 
> > Similarly to the core bus, this seems to have address ranges 0x03xxxxxx and
> > 0x18xxxxxx on it, so put those into the ranges.
> >
> 
> Okay we have an issue here. For whatever reason, the Cygnus ASIC team
> decided to put registers for the same block in random locations. We see
> similar issues in all of our other iProc based SoCs. We have
> communicated this to our ASIC team, and hopefully they can revert the
> trend for the next SoC.
> 
> For example, the gpio_ccm has registers in the following regions:
> 
> gpio_ccm: gpio@1800a000 {
>     compatible = "brcm,cygnus-ccm-gpio";
>     reg = <0x1800a000 0x50>,
>           <0x0301d164 0x20>;
> 
> NAND is worse, it has registers in 3 different separate regions:
> 
> nand: nand@18046000 {
>     compatible = "brcm,nand-iproc", "brcm,brcmnand-v6.1",
>                  "brcm,brcmnand";
>     reg = <0x18046000 0x600>, <0xf8105408 0x600>,
>           <0x18046f00 0x20>;
> 
> As you can see, this makes it impossible to define a proper address
> range for the bus; therefore, I'll have to keep the ranges undefined and
> a simple 1:1 mapping under this bus.

Hmm, you could still try to list them as non-overlapping with other
buses on the root node like

	ranges = <0x03000000 0x03000000 0x01000000>,
		 <0x18000000 0x18000000 0x01000000>,
		 <0xf8000000 0xf8000000 0x01000000>;

which clarifies how the bus is wired up in hardware.

Alternatively, you could make a more elaborate mapping, if there
are in fact multiple hardware ranges, like

	#address-cells = <2>; # space:offset
	ranges = <1 0  0x03000000 0x01000000>,
		 <2 0  0x18000000 0x01000000>,
		 <3 0  0xf8000000 0x01000000>;

It really depends on what the hardware designers were thinking. If
the AXI bus actually decodes the entire 32-bit address range and devices
are just located at random addresses in there, your current scheme is
probably closest to reality.

> > It probably also makes sense to name the bus according to what kind of
> > bus (axi, ahb, plb, ...) is used here. If the soc has nested buses
> > (e.g. an ahb connected to an axi bus,) then model both of them in the DT.
> 
> Based on the block diagram from the ASIC team, it looks like all of them
> are connected to one major AXI fabric. I can rename the bus to AXI.

Ok.

	Arnd

Re: [PATCH v2 1/9] ARM: dts: consolidate aliases for Cygnus dt files

[Arnd Bergmann]

On Friday 18 September 2015 14:44:54 Ray Jui wrote:
> On 9/18/2015 2:27 PM, Arnd Bergmann wrote:
> > On Friday 18 September 2015 14:24:06 Ray Jui wrote:
> > 
> > The SoC has at least four uarts according to this, so it seems unlikely that
> > each board really only uses only the fourth one of them and labels it '0'
> > on the board. As soon as you get one board that has more than one uart wired
> > up, you would need to undo this.
> > 
> 
> I think Scott might have explained this in the past. uart3 is going to
> be used on all Cygnus boards (including all future boards) because the
> bootrom was designed to use uart3 as console and that won't change.
> 
> Let me know if you still think I need to move this back to the dts.

I would still like to see them stay in the .dts file, if only for
consistency with other platforms. 

Also, even if you can guarantee that uart3 is always used for the
console, that doesn't prevent board designers from adding more than
one uart, right?

	Arnd

Re: [PATCH v2 1/9] ARM: dts: consolidate aliases for Cygnus dt files

[Ray Jui]

On 9/23/2015 2:31 PM, Arnd Bergmann wrote:
> On Friday 18 September 2015 14:44:54 Ray Jui wrote:
>> On 9/18/2015 2:27 PM, Arnd Bergmann wrote:
>>> On Friday 18 September 2015 14:24:06 Ray Jui wrote:
>>>
>>> The SoC has at least four uarts according to this, so it seems unlikely that
>>> each board really only uses only the fourth one of them and labels it '0'
>>> on the board. As soon as you get one board that has more than one uart wired
>>> up, you would need to undo this.
>>>
>>
>> I think Scott might have explained this in the past. uart3 is going to
>> be used on all Cygnus boards (including all future boards) because the
>> bootrom was designed to use uart3 as console and that won't change.
>>
>> Let me know if you still think I need to move this back to the dts.
> 
> I would still like to see them stay in the .dts file, if only for
> consistency with other platforms. 
> 
> Also, even if you can guarantee that uart3 is always used for the
> console, that doesn't prevent board designers from adding more than
> one uart, right?
> 
> 	Arnd
> 

Okay. Given that this patch series has been merged by Florian, I'll
submit another patch to move it back to .dts files.

Thanks,

Ray

Re: [PATCH v2 1/9] ARM: dts: consolidate aliases for Cygnus dt files

[Florian Fainelli]

On 23/09/15 14:46, Ray Jui wrote:
> 
> 
> On 9/23/2015 2:31 PM, Arnd Bergmann wrote:
>> On Friday 18 September 2015 14:44:54 Ray Jui wrote:
>>> On 9/18/2015 2:27 PM, Arnd Bergmann wrote:
>>>> On Friday 18 September 2015 14:24:06 Ray Jui wrote:
>>>>
>>>> The SoC has at least four uarts according to this, so it seems unlikely that
>>>> each board really only uses only the fourth one of them and labels it '0'
>>>> on the board. As soon as you get one board that has more than one uart wired
>>>> up, you would need to undo this.
>>>>
>>>
>>> I think Scott might have explained this in the past. uart3 is going to
>>> be used on all Cygnus boards (including all future boards) because the
>>> bootrom was designed to use uart3 as console and that won't change.
>>>
>>> Let me know if you still think I need to move this back to the dts.
>>
>> I would still like to see them stay in the .dts file, if only for
>> consistency with other platforms. 
>>
>> Also, even if you can guarantee that uart3 is always used for the
>> console, that doesn't prevent board designers from adding more than
>> one uart, right?
>>
>> 	Arnd
>>
> 
> Okay. Given that this patch series has been merged by Florian, I'll
> submit another patch to move it back to .dts files.

You could send me either a replacement patch series (all 9), or an
individual patch to replace a previous version (e.g; replace v2 with a
v3), or an incremental one, whatever works for you.

Thanks!
-- 
Florian

Re: [PATCH v2 5/9] ARM: dts: Move all Cygnus peripherals into soc bus

[Ray Jui]

On 9/23/2015 2:29 PM, Arnd Bergmann wrote:
> On Friday 18 September 2015 15:11:27 Ray Jui wrote:
>> On 9/18/2015 2:34 PM, Arnd Bergmann wrote:
>>> On Friday 18 September 2015 14:24:10 Ray Jui wrote:
>>>> +       soc {
>>>> +               compatible = "simple-bus";
>>>> +               ranges;
>>>> +               #address-cells = <1>;
>>>> +               #size-cells = <1>;
>>>
>>>> +               pinctrl: pinctrl@0301d0c8 {
>>>>
>>>
>>> Similarly to the core bus, this seems to have address ranges 0x03xxxxxx and
>>> 0x18xxxxxx on it, so put those into the ranges.
>>>
>>
>> Okay we have an issue here. For whatever reason, the Cygnus ASIC team
>> decided to put registers for the same block in random locations. We see
>> similar issues in all of our other iProc based SoCs. We have
>> communicated this to our ASIC team, and hopefully they can revert the
>> trend for the next SoC.
>>
>> For example, the gpio_ccm has registers in the following regions:
>>
>> gpio_ccm: gpio@1800a000 {
>>     compatible = "brcm,cygnus-ccm-gpio";
>>     reg = <0x1800a000 0x50>,
>>           <0x0301d164 0x20>;
>>
>> NAND is worse, it has registers in 3 different separate regions:
>>
>> nand: nand@18046000 {
>>     compatible = "brcm,nand-iproc", "brcm,brcmnand-v6.1",
>>                  "brcm,brcmnand";
>>     reg = <0x18046000 0x600>, <0xf8105408 0x600>,
>>           <0x18046f00 0x20>;
>>
>> As you can see, this makes it impossible to define a proper address
>> range for the bus; therefore, I'll have to keep the ranges undefined and
>> a simple 1:1 mapping under this bus.
> 
> Hmm, you could still try to list them as non-overlapping with other
> buses on the root node like
> 
> 	ranges = <0x03000000 0x03000000 0x01000000>,
> 		 <0x18000000 0x18000000 0x01000000>,
> 		 <0xf8000000 0xf8000000 0x01000000>;
> 
> which clarifies how the bus is wired up in hardware.
> 
> Alternatively, you could make a more elaborate mapping, if there
> are in fact multiple hardware ranges, like
> 
> 	#address-cells = <2>; # space:offset
> 	ranges = <1 0  0x03000000 0x01000000>,
> 		 <2 0  0x18000000 0x01000000>,
> 		 <3 0  0xf8000000 0x01000000>;
> 
> It really depends on what the hardware designers were thinking. If
> the AXI bus actually decodes the entire 32-bit address range and devices
> are just located at random addresses in there, your current scheme is
> probably closest to reality.
> 

I see. Let me talk to our ASIC team to get this clarified. If in the end
the AXI bus decodes the entire 32-bit address space, no change will be
made. Otherwise, I'll submit another patch to list the actual address
space that the AXI bus decodes.

Thanks for the review. It's very helpful!

Ray

Re: [PATCH v2 5/9] ARM: dts: Move all Cygnus peripherals into soc bus

[Ray Jui]

On 9/23/2015 2:55 PM, Ray Jui wrote:
> 
> 
> On 9/23/2015 2:29 PM, Arnd Bergmann wrote:
>> On Friday 18 September 2015 15:11:27 Ray Jui wrote:
>>> On 9/18/2015 2:34 PM, Arnd Bergmann wrote:
>>>> On Friday 18 September 2015 14:24:10 Ray Jui wrote:
>>>>> +       soc {
>>>>> +               compatible = "simple-bus";
>>>>> +               ranges;
>>>>> +               #address-cells = <1>;
>>>>> +               #size-cells = <1>;
>>>>
>>>>> +               pinctrl: pinctrl@0301d0c8 {
>>>>>
>>>>
>>>> Similarly to the core bus, this seems to have address ranges 0x03xxxxxx and
>>>> 0x18xxxxxx on it, so put those into the ranges.
>>>>
>>>
>>> Okay we have an issue here. For whatever reason, the Cygnus ASIC team
>>> decided to put registers for the same block in random locations. We see
>>> similar issues in all of our other iProc based SoCs. We have
>>> communicated this to our ASIC team, and hopefully they can revert the
>>> trend for the next SoC.
>>>
>>> For example, the gpio_ccm has registers in the following regions:
>>>
>>> gpio_ccm: gpio@1800a000 {
>>>     compatible = "brcm,cygnus-ccm-gpio";
>>>     reg = <0x1800a000 0x50>,
>>>           <0x0301d164 0x20>;
>>>
>>> NAND is worse, it has registers in 3 different separate regions:
>>>
>>> nand: nand@18046000 {
>>>     compatible = "brcm,nand-iproc", "brcm,brcmnand-v6.1",
>>>                  "brcm,brcmnand";
>>>     reg = <0x18046000 0x600>, <0xf8105408 0x600>,
>>>           <0x18046f00 0x20>;
>>>
>>> As you can see, this makes it impossible to define a proper address
>>> range for the bus; therefore, I'll have to keep the ranges undefined and
>>> a simple 1:1 mapping under this bus.
>>
>> Hmm, you could still try to list them as non-overlapping with other
>> buses on the root node like
>>
>> 	ranges = <0x03000000 0x03000000 0x01000000>,
>> 		 <0x18000000 0x18000000 0x01000000>,
>> 		 <0xf8000000 0xf8000000 0x01000000>;
>>
>> which clarifies how the bus is wired up in hardware.
>>
>> Alternatively, you could make a more elaborate mapping, if there
>> are in fact multiple hardware ranges, like
>>
>> 	#address-cells = <2>; # space:offset
>> 	ranges = <1 0  0x03000000 0x01000000>,
>> 		 <2 0  0x18000000 0x01000000>,
>> 		 <3 0  0xf8000000 0x01000000>;
>>
>> It really depends on what the hardware designers were thinking. If
>> the AXI bus actually decodes the entire 32-bit address range and devices
>> are just located at random addresses in there, your current scheme is
>> probably closest to reality.
>>
> 
> I see. Let me talk to our ASIC team to get this clarified. If in the end
> the AXI bus decodes the entire 32-bit address space, no change will be
> made. Otherwise, I'll submit another patch to list the actual address
> space that the AXI bus decodes.
> 
> Thanks for the review. It's very helpful!
> 
> Ray
> 

I just got feedback from our ASIC team. The NIC-301 is the main AXI
fabric that decodes the entire 32-bit address space on Cygnus.

I'll keep this as it is for now.

Thanks,

Ray

Re: [PATCH v2 1/9] ARM: dts: consolidate aliases for Cygnus dt files

[Ray Jui]

On 9/23/2015 2:48 PM, Florian Fainelli wrote:
> On 23/09/15 14:46, Ray Jui wrote:
>>
>>
>> On 9/23/2015 2:31 PM, Arnd Bergmann wrote:
>>> On Friday 18 September 2015 14:44:54 Ray Jui wrote:
>>>> On 9/18/2015 2:27 PM, Arnd Bergmann wrote:
>>>>> On Friday 18 September 2015 14:24:06 Ray Jui wrote:
>>>>>
>>>>> The SoC has at least four uarts according to this, so it seems unlikely that
>>>>> each board really only uses only the fourth one of them and labels it '0'
>>>>> on the board. As soon as you get one board that has more than one uart wired
>>>>> up, you would need to undo this.
>>>>>
>>>>
>>>> I think Scott might have explained this in the past. uart3 is going to
>>>> be used on all Cygnus boards (including all future boards) because the
>>>> bootrom was designed to use uart3 as console and that won't change.
>>>>
>>>> Let me know if you still think I need to move this back to the dts.
>>>
>>> I would still like to see them stay in the .dts file, if only for
>>> consistency with other platforms. 
>>>
>>> Also, even if you can guarantee that uart3 is always used for the
>>> console, that doesn't prevent board designers from adding more than
>>> one uart, right?
>>>
>>> 	Arnd
>>>
>>
>> Okay. Given that this patch series has been merged by Florian, I'll
>> submit another patch to move it back to .dts files.
> 
> You could send me either a replacement patch series (all 9), or an
> individual patch to replace a previous version (e.g; replace v2 with a
> v3), or an incremental one, whatever works for you.
> 
> Thanks!
> 

Hi Florian, I just sent you an incremental patch to move the alias back
to .dts files.

Thanks,

Ray