From: Krzysztof Kozlowski <k.kozlowski@samsung.com>
To: rtc-linux@googlegroups.com, Alim Akhtar <alim.akhtar@samsung.com>
Cc: k.kozlowski.k@gmail.com, lee.jones@linaro.org,
broonie@kernel.org, linux-samsung-soc@vger.kernel.org,
linux-kernel@vger.kernel.org,
Thomas Abraham <thomas.ab@samsung.com>,
devicetree@vger.kernel.org
Subject: Re: [rtc-linux] Re: [PATCH v5 1/4] dt-bindings: mfd: s2mps11: add documentation for s2mps15 PMIC
Date: Sat, 7 Nov 2015 12:09:38 +0900 [thread overview]
Message-ID: <563D6B72.9010004@samsung.com> (raw)
In-Reply-To: <20151106223339.GA22411@rob-hp-laptop>
W dniu 07.11.2015 o 07:33, Rob Herring pisze:
> On Fri, Oct 30, 2015 at 11:55:31AM +0530, Alim Akhtar wrote:
>> From: Thomas Abraham <thomas.ab@samsung.com>
>>
>> Add dt-binding documentation for s2mps15 PMIC device. The s2mps15 device
>> is similar to s2mps11/14 PMIC device and has 27 LDO and 10 buck regulators.
>> This also supports RTC and three 32.768KHz clock outputs.
>>
>> Cc: devicetree@vger.kernel.org
>> Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
>> Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
>> ---
>> Documentation/devicetree/bindings/mfd/s2mps11.txt | 21 ++++++++++++++-------
>> 1 file changed, 14 insertions(+), 7 deletions(-)
>>
>> diff --git a/Documentation/devicetree/bindings/mfd/s2mps11.txt b/Documentation/devicetree/bindings/mfd/s2mps11.txt
>> index 890f0b0e1643..4c0543ceec25 100644
>> --- a/Documentation/devicetree/bindings/mfd/s2mps11.txt
>> +++ b/Documentation/devicetree/bindings/mfd/s2mps11.txt
>> @@ -1,5 +1,5 @@
>>
>> -* Samsung S2MPS11, S2MPS13, S2MPS14 and S2MPU02 Voltage and Current Regulator
>> +* Samsung S2MPS11/13/14/15 and S2MPU02 Voltage and Current Regulator
>>
>> The Samsung S2MPS11 is a multi-function device which includes voltage and
>> current regulators, RTC, charger controller and other sub-blocks. It is
>> @@ -7,8 +7,12 @@ interfaced to the host controller using an I2C interface. Each sub-block is
>> addressed by the host system using different I2C slave addresses.
>>
>> Required properties:
>> -- compatible: Should be "samsung,s2mps11-pmic" or "samsung,s2mps13-pmic"
>> - or "samsung,s2mps14-pmic" or "samsung,s2mpu02-pmic".
>> +- compatible: Should be one of the following
>> + - "samsung,s2mps11-pmic"
>> + - "samsung,s2mps13-pmic"
>> + - "samsung,s2mps14-pmic"
>> + - "samsung,s2mps15-pmic"
>> + - "samsung,s2mpu02-pmic".
>> - reg: Specifies the I2C slave address of the pmic block. It should be 0x66.
>>
>> Optional properties:
>> @@ -24,7 +28,7 @@ Optional properties:
>> unwanted buck warm reset (setting buck voltages to default values).
>>
>> Optional nodes:
>> -- clocks: s2mps11, s2mps13 and s5m8767 provide three(AP/CP/BT) buffered 32.768
>> +- clocks: s2mps11, s2mps13, s2mps15 and s5m8767 provide three(AP/CP/BT) buffered 32.768
>
> s5m8767 doesn't seem to be documented. Can you please fix or remove.
What exactly do you have in mind?
The s5m8767-clk is already documented as part of clk-s2mps11.c driver:
Documentation/devicetree/bindings/mfd/s2mps11.txt
The main s5m8767 MFD driver is documented as part of regulator driver:
Documentation/devicetree/bindings/regulator/s5m8767-regulator.txt
Yes, this may be confusing... They S2M and S5M family devices share:
- main mfd driver,
- rtc driver,
- clk driver.
but regulator drivers are separate.
Best regards,
Krzysztof
next prev parent reply other threads:[~2015-11-07 3:09 UTC|newest]
Thread overview: 26+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-10-30 6:25 [PATCH v5 0/4] mfd: sec: add S2MPS15 PMIC support Alim Akhtar
2015-10-30 6:25 ` [PATCH v5 1/4] dt-bindings: mfd: s2mps11: add documentation for s2mps15 PMIC Alim Akhtar
2015-10-30 7:42 ` Krzysztof Kozlowski
2015-10-30 9:25 ` Alim Akhtar
2015-10-30 17:24 ` Lee Jones
2015-11-06 22:33 ` Rob Herring
2015-11-07 1:11 ` Alim Akhtar
2015-11-07 3:09 ` Krzysztof Kozlowski [this message]
2015-11-09 5:54 ` [rtc-linux] " Alim Akhtar
2015-11-09 6:40 ` Krzysztof Kozlowski
2015-10-30 6:25 ` [PATCH v5 2/4] mfd: sec: Add support for S2MPS15 PMIC Alim Akhtar
2015-10-30 6:25 ` [PATCH v5 3/4] regulator: s2mps11: add support for S2MPS15 regulators Alim Akhtar
2015-10-30 6:25 ` [PATCH v5 4/4] drivers/rtc/rtc-s5m.c: add support for S2MPS15 RTC Alim Akhtar
2015-10-30 8:38 ` Krzysztof Kozlowski
2015-10-30 9:28 ` Alim Akhtar
2015-10-30 17:23 ` Lee Jones
2015-11-01 17:40 ` Alexandre Belloni
2015-11-01 23:46 ` Krzysztof Kozlowski
2015-11-02 0:47 ` Alexandre Belloni
2015-11-02 9:03 ` Lee Jones
2015-11-02 10:19 ` Alexandre Belloni
2015-11-02 10:58 ` Lee Jones
2015-11-19 18:00 ` [PATCH v5 0/4] mfd: sec: add S2MPS15 PMIC support Alim Akhtar
2015-11-20 9:05 ` Lee Jones
2015-11-20 9:15 ` Alim Akhtar
2015-11-20 10:31 ` Lee Jones
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=563D6B72.9010004@samsung.com \
--to=k.kozlowski@samsung.com \
--cc=alim.akhtar@samsung.com \
--cc=broonie@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=k.kozlowski.k@gmail.com \
--cc=lee.jones@linaro.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-samsung-soc@vger.kernel.org \
--cc=rtc-linux@googlegroups.com \
--cc=thomas.ab@samsung.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).