[PATCH 0/2] mvneta: implement ethtool autonegotiation control

[PATCH 0/2] mvneta: implement ethtool autonegotiation control

[Stas Sergeev]

These 2 patches add an ability to control the
autonegotiation via ethtool. For example:

ethtool -s eth0 autoneg off
ethtool -s eth0 autoneg on

This is needed if you want to connect the mvneta's MII
to different switches or PHYs: the ones the do support
the in-band status, and the ones that do not.

[PATCH 1/2] mvneta: consolidate autoneg enabling

[Stas Sergeev]

This moves autoneg-related bit manipulations to the single place.

CC: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
CC: netdev@vger.kernel.org
CC: linux-kernel@vger.kernel.org

Signed-off-by: Stas Sergeev <stsp@users.sourceforge.net>
---
 drivers/net/ethernet/marvell/mvneta.c | 16 +++++++++++++---
 1 file changed, 13 insertions(+), 3 deletions(-)

diff --git a/drivers/net/ethernet/marvell/mvneta.c b/drivers/net/ethernet/marvell/mvneta.c
index e84c7f2..8e0e6de 100644
--- a/drivers/net/ethernet/marvell/mvneta.c
+++ b/drivers/net/ethernet/marvell/mvneta.c
@@ -1065,15 +1065,28 @@ static void mvneta_defaults_set(struct mvneta_port *pp)
 		       MVNETA_GMAC_AN_SPEED_EN |
 		       MVNETA_GMAC_AN_DUPLEX_EN;
 		mvreg_write(pp, MVNETA_GMAC_AUTONEG_CONFIG, val);
+
 		val = mvreg_read(pp, MVNETA_GMAC_CLOCK_DIVIDER);
 		val |= MVNETA_GMAC_1MS_CLOCK_ENABLE;
 		mvreg_write(pp, MVNETA_GMAC_CLOCK_DIVIDER, val);
+
+		val = mvreg_read(pp, MVNETA_GMAC_CTRL_2);
+		val |= MVNETA_GMAC2_INBAND_AN_ENABLE;
+		mvreg_write(pp, MVNETA_GMAC_CTRL_2, val);
 	} else {
 		val = mvreg_read(pp, MVNETA_GMAC_AUTONEG_CONFIG);
 		val &= ~(MVNETA_GMAC_INBAND_AN_ENABLE |
 		       MVNETA_GMAC_AN_SPEED_EN |
 		       MVNETA_GMAC_AN_DUPLEX_EN);
 		mvreg_write(pp, MVNETA_GMAC_AUTONEG_CONFIG, val);
+
+		val = mvreg_read(pp, MVNETA_GMAC_CLOCK_DIVIDER);
+		val &= ~MVNETA_GMAC_1MS_CLOCK_ENABLE;
+		mvreg_write(pp, MVNETA_GMAC_CLOCK_DIVIDER, val);
+
+		val = mvreg_read(pp, MVNETA_GMAC_CTRL_2);
+		val &= ~MVNETA_GMAC2_INBAND_AN_ENABLE;
+		mvreg_write(pp, MVNETA_GMAC_CTRL_2, val);
 	}

 	mvneta_set_ucast_table(pp, -1);
@@ -3223,9 +3236,6 @@ static int mvneta_port_power_up(struct mvneta_port *pp, int phy_mode)
 		return -EINVAL;
 	}

-	if (pp->use_inband_status)
-		ctrl |= MVNETA_GMAC2_INBAND_AN_ENABLE;
-
 	/* Cancel Port Reset */
 	ctrl &= ~MVNETA_GMAC2_PORT_RESET;
 	mvreg_write(pp, MVNETA_GMAC_CTRL_2, ctrl);
-- 
2.4.3

[PATCH 2/2] mvneta: implement ethtool autonegotiation control

[Stas Sergeev]

This patch allows to do
ethtool -s eth0 autoneg off
ethtool -s eth0 autoneg on
to disable or enable autonegotiation at run-time.
Without that functionality, the only way to control the autonegotiation
is to modify the device tree.

This is needed if you plan to use the same kernel with
different ethernet switches, the ones that support the in-band
status and the ones that not.

CC: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
CC: netdev@vger.kernel.org
CC: linux-kernel@vger.kernel.org

Signed-off-by: Stas Sergeev <stsp@users.sourceforge.net>
---
 drivers/net/ethernet/marvell/mvneta.c | 109 +++++++++++++++++++++++-----------
 1 file changed, 74 insertions(+), 35 deletions(-)

diff --git a/drivers/net/ethernet/marvell/mvneta.c b/drivers/net/ethernet/marvell/mvneta.c
index 8e0e6de..d0e1ec5 100644
--- a/drivers/net/ethernet/marvell/mvneta.c
+++ b/drivers/net/ethernet/marvell/mvneta.c
@@ -369,7 +369,7 @@ struct mvneta_port {
 	unsigned int duplex;
 	unsigned int speed;
 	unsigned int tx_csum_limit;
-	int use_inband_status:1;
+	unsigned int use_inband_status:1;

 	u64 ethtool_stats[ARRAY_SIZE(mvneta_statistics)];
 };
@@ -971,6 +971,44 @@ static void mvneta_set_other_mcast_table(struct mvneta_port *pp, int queue)
 		mvreg_write(pp, MVNETA_DA_FILT_OTH_MCAST + offset, val);
 }

+static void mvneta_set_autoneg(struct mvneta_port *pp, int enable)
+{
+	u32 val;
+
+	if (enable) {
+		val = mvreg_read(pp, MVNETA_GMAC_AUTONEG_CONFIG);
+		val &= ~(MVNETA_GMAC_FORCE_LINK_PASS |
+			 MVNETA_GMAC_FORCE_LINK_DOWN |
+			 MVNETA_GMAC_AN_FLOW_CTRL_EN);
+		val |= MVNETA_GMAC_INBAND_AN_ENABLE |
+		       MVNETA_GMAC_AN_SPEED_EN |
+		       MVNETA_GMAC_AN_DUPLEX_EN;
+		mvreg_write(pp, MVNETA_GMAC_AUTONEG_CONFIG, val);
+
+		val = mvreg_read(pp, MVNETA_GMAC_CLOCK_DIVIDER);
+		val |= MVNETA_GMAC_1MS_CLOCK_ENABLE;
+		mvreg_write(pp, MVNETA_GMAC_CLOCK_DIVIDER, val);
+
+		val = mvreg_read(pp, MVNETA_GMAC_CTRL_2);
+		val |= MVNETA_GMAC2_INBAND_AN_ENABLE;
+		mvreg_write(pp, MVNETA_GMAC_CTRL_2, val);
+	} else {
+		val = mvreg_read(pp, MVNETA_GMAC_AUTONEG_CONFIG);
+		val &= ~(MVNETA_GMAC_INBAND_AN_ENABLE |
+		       MVNETA_GMAC_AN_SPEED_EN |
+		       MVNETA_GMAC_AN_DUPLEX_EN);
+		mvreg_write(pp, MVNETA_GMAC_AUTONEG_CONFIG, val);
+
+		val = mvreg_read(pp, MVNETA_GMAC_CLOCK_DIVIDER);
+		val &= ~MVNETA_GMAC_1MS_CLOCK_ENABLE;
+		mvreg_write(pp, MVNETA_GMAC_CLOCK_DIVIDER, val);
+
+		val = mvreg_read(pp, MVNETA_GMAC_CTRL_2);
+		val &= ~MVNETA_GMAC2_INBAND_AN_ENABLE;
+		mvreg_write(pp, MVNETA_GMAC_CTRL_2, val);
+	}
+}
+
 /* This method sets defaults to the NETA port:
  *	Clears interrupt Cause and Mask registers.
  *	Clears all MAC tables.
@@ -1056,39 +1094,7 @@ static void mvneta_defaults_set(struct mvneta_port *pp)
 	val &= ~MVNETA_PHY_POLLING_ENABLE;
 	mvreg_write(pp, MVNETA_UNIT_CONTROL, val);

-	if (pp->use_inband_status) {
-		val = mvreg_read(pp, MVNETA_GMAC_AUTONEG_CONFIG);
-		val &= ~(MVNETA_GMAC_FORCE_LINK_PASS |
-			 MVNETA_GMAC_FORCE_LINK_DOWN |
-			 MVNETA_GMAC_AN_FLOW_CTRL_EN);
-		val |= MVNETA_GMAC_INBAND_AN_ENABLE |
-		       MVNETA_GMAC_AN_SPEED_EN |
-		       MVNETA_GMAC_AN_DUPLEX_EN;
-		mvreg_write(pp, MVNETA_GMAC_AUTONEG_CONFIG, val);
-
-		val = mvreg_read(pp, MVNETA_GMAC_CLOCK_DIVIDER);
-		val |= MVNETA_GMAC_1MS_CLOCK_ENABLE;
-		mvreg_write(pp, MVNETA_GMAC_CLOCK_DIVIDER, val);
-
-		val = mvreg_read(pp, MVNETA_GMAC_CTRL_2);
-		val |= MVNETA_GMAC2_INBAND_AN_ENABLE;
-		mvreg_write(pp, MVNETA_GMAC_CTRL_2, val);
-	} else {
-		val = mvreg_read(pp, MVNETA_GMAC_AUTONEG_CONFIG);
-		val &= ~(MVNETA_GMAC_INBAND_AN_ENABLE |
-		       MVNETA_GMAC_AN_SPEED_EN |
-		       MVNETA_GMAC_AN_DUPLEX_EN);
-		mvreg_write(pp, MVNETA_GMAC_AUTONEG_CONFIG, val);
-
-		val = mvreg_read(pp, MVNETA_GMAC_CLOCK_DIVIDER);
-		val &= ~MVNETA_GMAC_1MS_CLOCK_ENABLE;
-		mvreg_write(pp, MVNETA_GMAC_CLOCK_DIVIDER, val);
-
-		val = mvreg_read(pp, MVNETA_GMAC_CTRL_2);
-		val &= ~MVNETA_GMAC2_INBAND_AN_ENABLE;
-		mvreg_write(pp, MVNETA_GMAC_CTRL_2, val);
-	}
-
+	mvneta_set_autoneg(pp, pp->use_inband_status);
 	mvneta_set_ucast_table(pp, -1);
 	mvneta_set_special_mcast_table(pp, -1);
 	mvneta_set_other_mcast_table(pp, -1);
@@ -2950,10 +2956,43 @@ int mvneta_ethtool_get_settings(struct net_device *dev, struct ethtool_cmd *cmd)
 int mvneta_ethtool_set_settings(struct net_device *dev, struct ethtool_cmd *cmd)
 {
 	struct mvneta_port *pp = netdev_priv(dev);
+	struct phy_device *phydev = pp->phy_dev;

-	if (!pp->phy_dev)
+	if (!phydev)
 		return -ENODEV;

+	if ((cmd->autoneg == AUTONEG_ENABLE) != pp->use_inband_status) {
+		u32 val;
+
+		mvneta_set_autoneg(pp, cmd->autoneg == AUTONEG_ENABLE);
+
+		if (cmd->autoneg == AUTONEG_DISABLE) {
+			val = mvreg_read(pp, MVNETA_GMAC_AUTONEG_CONFIG);
+			val &= ~(MVNETA_GMAC_CONFIG_MII_SPEED |
+				 MVNETA_GMAC_CONFIG_GMII_SPEED |
+				 MVNETA_GMAC_CONFIG_FULL_DUPLEX);
+
+			if (phydev->duplex)
+				val |= MVNETA_GMAC_CONFIG_FULL_DUPLEX;
+
+			if (phydev->speed == SPEED_1000)
+				val |= MVNETA_GMAC_CONFIG_GMII_SPEED;
+			else if (phydev->speed == SPEED_100)
+				val |= MVNETA_GMAC_CONFIG_MII_SPEED;
+
+			mvreg_write(pp, MVNETA_GMAC_AUTONEG_CONFIG, val);
+		}
+
+		pp->use_inband_status = (cmd->autoneg == AUTONEG_ENABLE);
+		netdev_info(pp->dev, "autoneg status set to %i\n",
+			    pp->use_inband_status);
+
+		if (netif_running(dev)) {
+			mvneta_port_down(pp);
+			mvneta_port_up(pp);
+		}
+	}
+
 	return phy_ethtool_sset(pp->phy_dev, cmd);
 }

-- 
2.4.3

Re: [PATCH 0/2] mvneta: implement ethtool autonegotiation control

[David Miller]

From: Stas Sergeev <stsp@list.ru>
Date: Wed, 2 Dec 2015 20:32:24 +0300

> These 2 patches add an ability to control the
> autonegotiation via ethtool. For example:
> 
> ethtool -s eth0 autoneg off
> ethtool -s eth0 autoneg on
> 
> This is needed if you want to connect the mvneta's MII
> to different switches or PHYs: the ones the do support
> the in-band status, and the ones that do not.

Series applied to net-next, thanks.