* [PATCH v2] ARM64: boot: dts: Add regulators for Tegra210 Smaug
@ 2016-06-09 17:38 Rhyland Klein
2016-06-10 6:28 ` Laxman Dewangan
0 siblings, 1 reply; 2+ messages in thread
From: Rhyland Klein @ 2016-06-09 17:38 UTC (permalink / raw)
To: Laxman Dewangan, Thierry Reding
Cc: Stephen Warren, Jon Hunter, Alexandre Courbot, Andrew Bresticker,
devicetree, linux-tegra, linux-kernel, Rhyland Klein
Add regulators to the Tegra210 Smaug DTS file including
support for the max77620 PMIC.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
---
v2:
- Updated reg properties to match current binding
arch/arm64/boot/dts/nvidia/tegra210-smaug.dts | 323 ++++++++++++++++++++++++++
1 file changed, 323 insertions(+)
diff --git a/arch/arm64/boot/dts/nvidia/tegra210-smaug.dts b/arch/arm64/boot/dts/nvidia/tegra210-smaug.dts
index 4d89f4e02d98..b2d16b7c6809 100644
--- a/arch/arm64/boot/dts/nvidia/tegra210-smaug.dts
+++ b/arch/arm64/boot/dts/nvidia/tegra210-smaug.dts
@@ -1,6 +1,7 @@
/dts-v1/;
#include <dt-bindings/input/input.h>
+#include <dt-bindings/mfd/max77620.h>
#include <dt-bindings/pinctrl/pinctrl-tegra.h>
#include "tegra210.dtsi"
@@ -1327,6 +1328,242 @@
};
};
+ i2c@7000d000 {
+ status = "okay";
+ clock-frequency = <1000000>;
+
+ max77620: max77620@3c {
+ compatible = "maxim,max77620";
+ reg = <0x3c>;
+ interrupts = <0 86 IRQ_TYPE_NONE>;
+
+ #interrupt-cells = <2>;
+ interrupt-controller;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&max77620_default>;
+
+ max77620_default: pinmux@0 {
+ pin_gpio {
+ pins = "gpio0", "gpio1", "gpio2", "gpio7";
+ function = "gpio";
+ };
+
+ /*
+ * GPIO3 is used to en_pp3300, and it is part of power
+ * sequence, So it must be sequenced up (automatically
+ * set by OTP) and down properly.
+ */
+ pin_gpio3 {
+ pins = "gpio3";
+ function = "fps-out";
+ drive-open-drain = <1>;
+ maxim,active-fps-source = <MAX77620_FPS_SRC_0>;
+ maxim,active-fps-power-up-slot = <4>;
+ maxim,active-fps-power-down-slot = <2>;
+ };
+
+ pin_gpio5_6 {
+ pins = "gpio5", "gpio6";
+ function = "gpio";
+ drive-push-pull = <1>;
+ };
+
+ pin_32k {
+ pins = "gpio4";
+ function = "32k-out1";
+ };
+ };
+
+ fps {
+ fps0 {
+ maxim,shutdown-fps-time-period-us = <5120>;
+ maxim,fps-event-source = <MAX77620_FPS_EVENT_SRC_EN0>;
+ };
+
+ fps1 {
+ maxim,shutdown-fps-time-period-us = <5120>;
+ maxim,fps-event-source = <MAX77620_FPS_EVENT_SRC_EN1>;
+ maxim,enable-sleep;
+ };
+
+ fps2 {
+ maxim,fps-event-source = <MAX77620_FPS_EVENT_SRC_EN0>;
+ };
+ };
+
+ regulators {
+ in-ldo0-1-supply = <&pp1350>;
+ in-ldo2-supply = <&pp3300>;
+ in-ldo3-5-supply = <&pp3300>;
+ in-ldo7-8-supply = <&pp1350>;
+
+ ppvar_soc: sd0 {
+ regulator-name = "PPVAR_SOC";
+ regulator-min-microvolt = <825000>;
+ regulator-max-microvolt = <1125000>;
+ regulator-enable-ramp-delay = <146>;
+ regulator-always-on;
+ regulator-boot-on;
+ maxim,ramp-rate-setting = <27500>;
+ maxim,active-fps-source = <MAX77620_FPS_SRC_1>;
+ maxim,active-fps-power-up-slot = <1>;
+ maxim,active-fps-power-down-slot = <7>;
+ };
+
+ pp1100_sd1: sd1 {
+ regulator-name = "PP1100";
+ regulator-min-microvolt = <1125000>;
+ regulator-max-microvolt = <1125000>;
+ regulator-enable-ramp-delay = <130>;
+ regulator-always-on;
+ regulator-boot-on;
+ maxim,ramp-rate-setting = <27500>;
+ maxim,active-fps-source = <MAX77620_FPS_SRC_0>;
+ maxim,active-fps-power-up-slot = <5>;
+ maxim,active-fps-power-down-slot = <1>;
+ };
+
+ pp1350: sd2 {
+ regulator-name = "PP1350";
+ regulator-min-microvolt = <1350000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-enable-ramp-delay = <176>;
+ regulator-always-on;
+ regulator-boot-on;
+ maxim,ramp-rate-setting = <27500>;
+ maxim,active-fps-source = <MAX77620_FPS_SRC_NONE>;
+ maxim,active-fps-power-up-slot = <2>;
+ maxim,active-fps-power-down-slot = <5>;
+ };
+
+ pp1800: sd3 {
+ regulator-name = "PP1800";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-enable-ramp-delay = <242>;
+ regulator-always-on;
+ regulator-boot-on;
+ maxim,ramp-rate-setting = <27500>;
+ maxim,active-fps-source = <MAX77620_FPS_SRC_0>;
+ maxim,active-fps-power-up-slot = <3>;
+ maxim,active-fps-power-down-slot = <3>;
+ };
+
+ pp1200_avdd: ldo0 {
+ regulator-name = "PP1200_AVDD";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-enable-ramp-delay = <26>;
+ regulator-boot-on;
+ maxim,ramp-rate-setting = <100000>;
+ maxim,active-fps-source = <MAX77620_FPS_SRC_NONE>;
+ maxim,active-fps-power-up-slot = <0>;
+ maxim,active-fps-power-down-slot = <7>;
+ };
+
+ pp1200_rcam: ldo1 {
+ regulator-name = "PP1200_RCAM";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-enable-ramp-delay = <22>;
+ maxim,ramp-rate-setting = <100000>;
+ maxim,active-fps-source = <MAX77620_FPS_SRC_NONE>;
+ maxim,active-fps-power-up-slot = <0>;
+ maxim,active-fps-power-down-slot = <7>;
+ };
+
+ pp_ldo2: ldo2 {
+ regulator-name = "PP_LDO2";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-enable-ramp-delay = <62>;
+ regulator-always-on;
+ regulator-boot-on;
+ maxim,ramp-rate-setting = <100000>;
+ maxim,active-fps-source = <MAX77620_FPS_SRC_NONE>;
+ maxim,active-fps-power-up-slot = <0>;
+ maxim,active-fps-power-down-slot = <7>;
+ };
+
+ pp2800l_rcam: ldo3 {
+ regulator-name = "PP2800L_RCAM";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-enable-ramp-delay = <50>;
+ maxim,ramp-rate-setting = <100000>;
+ maxim,active-fps-source = <MAX77620_FPS_SRC_NONE>;
+ maxim,active-fps-power-up-slot = <0>;
+ maxim,active-fps-power-down-slot = <7>;
+ };
+
+ pp100_soc_rtc: ldo4 {
+ regulator-name = "PP1100_SOC_RTC";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <850000>;
+ regulator-enable-ramp-delay = <22>;
+ regulator-always-on; /* Check this */
+ regulator-boot-on;
+ maxim,ramp-rate-setting = <100000>;
+ maxim,active-fps-source = <MAX77620_FPS_SRC_0>;
+ maxim,active-fps-power-up-slot = <1>;
+ maxim,active-fps-power-down-slot = <7>;
+ };
+
+ pp2800l_fcam: ldo5 {
+ regulator-name = "PP2800L_FCAM";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-enable-ramp-delay = <62>;
+ maxim,ramp-rate-setting = <100000>;
+ maxim,active-fps-source = <MAX77620_FPS_SRC_NONE>;
+ maxim,active-fps-power-up-slot = <0>;
+ maxim,active-fps-power-down-slot = <7>;
+ };
+
+ ldo6 {
+ /* Unused. */
+ regulator-name = "PP_LDO6";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-enable-ramp-delay = <36>;
+ maxim,ramp-rate-setting = <100000>;
+ maxim,active-fps-source = <MAX77620_FPS_SRC_NONE>;
+ maxim,active-fps-power-up-slot = <0>;
+ maxim,active-fps-power-down-slot = <7>;
+ };
+
+ pp1050_avdd: ldo7 {
+ regulator-name = "PP1050_AVDD";
+ regulator-min-microvolt = <1050000>;
+ regulator-max-microvolt = <1050000>;
+ regulator-enable-ramp-delay = <24>;
+ regulator-always-on;
+ regulator-boot-on;
+ maxim,ramp-rate-setting = <100000>;
+ maxim,active-fps-source = <MAX77620_FPS_SRC_1>;
+ maxim,active-fps-power-up-slot = <3>;
+ maxim,active-fps-power-down-slot = <4>;
+ };
+
+ avddio_1v05: ldo8 {
+ regulator-name = "AVDDIO_1V05";
+ regulator-min-microvolt = <1050000>;
+ regulator-max-microvolt = <1050000>;
+ regulator-enable-ramp-delay = <22>;
+ regulator-boot-on;
+ maxim,ramp-rate-setting = <100000>;
+ maxim,active-fps-source = <MAX77620_FPS_SRC_NONE>;
+ maxim,active-fps-power-up-slot = <0>;
+ maxim,active-fps-power-down-slot = <7>;
+ };
+ };
+ };
+ };
+
pmc@7000e400 {
nvidia,invert-interrupt;
nvidia,suspend-mode = <0>;
@@ -1421,4 +1658,90 @@
compatible = "arm,psci-1.0";
method = "smc";
};
+
+ regulators {
+ compatible = "simple-bus";
+ device_type = "fixed-regulators";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ppvar_sys: regulator@0 {
+ compatible = "regulator-fixed";
+ reg = <0>;
+ regulator-name = "PPVAR_SYS";
+ regulator-min-microvolt = <4400000>;
+ regulator-max-microvolt = <4400000>;
+ regulator-always-on;
+ };
+
+ pplcd_vdd: regulator@1 {
+ compatible = "regulator-fixed";
+ reg = <1>;
+ regulator-name = "PPLCD_VDD";
+ regulator-min-microvolt = <4400000>;
+ regulator-max-microvolt = <4400000>;
+ gpio = <&gpio TEGRA_GPIO(V, 4) 0>;
+ enable-active-high;
+ regulator-boot-on;
+ };
+
+ pp3000_always: regulator@2 {
+ compatible = "regulator-fixed";
+ reg = <2>;
+ regulator-name = "PP3000_ALWAYS";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-always-on;
+ };
+
+ pp3300: regulator@3 {
+ compatible = "regulator-fixed";
+ reg = <3>;
+ regulator-name = "PP3300";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ gpio = <&max77620 3 0>;
+ enable-active-high;
+ };
+
+ pp5000: regulator@4 {
+ compatible = "regulator-fixed";
+ reg = <4>;
+ regulator-name = "PP5000";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+
+ pp1800_lcdio: regulator@5 {
+ compatible = "regulator-fixed";
+ reg = <5>;
+ regulator-name = "PP1800_LCDIO";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ gpio = <&gpio TEGRA_GPIO(V, 3) 0>;
+ enable-active-high;
+ regulator-boot-on;
+ };
+
+ pp1800_cam: regulator@6 {
+ compatible = "regulator-fixed";
+ reg= <6>;
+ regulator-name = "PP1800_CAM";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ gpio = <&gpio TEGRA_GPIO(K, 3) 0>;
+ enable-active-high;
+ };
+
+ usbc_vbus: regulator@7 {
+ compatible = "regulator-fixed";
+ reg = <7>;
+ regulator-name = "USBC_VBUS";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+ };
};
--
1.9.1
^ permalink raw reply related [flat|nested] 2+ messages in thread
* Re: [PATCH v2] ARM64: boot: dts: Add regulators for Tegra210 Smaug
2016-06-09 17:38 [PATCH v2] ARM64: boot: dts: Add regulators for Tegra210 Smaug Rhyland Klein
@ 2016-06-10 6:28 ` Laxman Dewangan
0 siblings, 0 replies; 2+ messages in thread
From: Laxman Dewangan @ 2016-06-10 6:28 UTC (permalink / raw)
To: Rhyland Klein, Thierry Reding
Cc: Stephen Warren, Jon Hunter, Alexandre Courbot, Andrew Bresticker,
devicetree, linux-tegra, linux-kernel
On Thursday 09 June 2016 11:08 PM, Rhyland Klein wrote:
> Add regulators to the Tegra210 Smaug DTS file including
> support for the max77620 PMIC.
>
> Signed-off-by: Rhyland Klein <rklein@nvidia.com>
>
> +
> + fps1 {
> + maxim,shutdown-fps-time-period-us = <5120>;
> + maxim,fps-event-source = <MAX77620_FPS_EVENT_SRC_EN1>;
> + maxim,enable-sleep;
The maxim,enabel-sleep is not the valid property.
It should be
maxim,device-state-on-disabled-event = <MAX77620_FPS_INACTIVE_STATE_SLEEP>;
> + };
> +
> + fps2 {
> + maxim,fps-event-source = <MAX77620_FPS_EVENT_SRC_EN0>;
> + };
> + };
> +
> + regulators {
> + in-ldo0-1-supply = <&pp1350>;
> + in-ldo2-supply = <&pp3300>;
> + in-ldo3-5-supply = <&pp3300>;
> + in-ldo7-8-supply = <&pp1350>;
> +
> + ppvar_soc: sd0 {
> + regulator-name = "PPVAR_SOC";
> + regulator-min-microvolt = <825000>;
> + regulator-max-microvolt = <1125000>;
> + regulator-enable-ramp-delay = <146>;
> + regulator-always-on;
> + regulator-boot-on;
> + maxim,ramp-rate-setting = <27500>;
You need to say regulator-ramp-delay if register config is same as what
platform observed.
This is applicable for all places.
> + regulator-always-on;
> + gpio = <&max77620 3 0>;
GPIO3 is fps-out and hence it can not be done here. Better to do not
provide any gpio entry.
^ permalink raw reply [flat|nested] 2+ messages in thread
end of thread, other threads:[~2016-06-10 6:41 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2016-06-09 17:38 [PATCH v2] ARM64: boot: dts: Add regulators for Tegra210 Smaug Rhyland Klein
2016-06-10 6:28 ` Laxman Dewangan
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).