From: Konrad Dybcio <konrad.dybcio@somainline.org>
To: Bhupesh Sharma <bhupesh.sharma@linaro.org>,
linux-arm-msm@vger.kernel.org
Cc: bhupesh.linux@gmail.com, linux-gpio@vger.kernel.org,
linux-kernel@vger.kernel.org, devicetree@vger.kernel.org,
robh+dt@kernel.org, agross@kernel.org,
Mark Brown <broonie@kernel.org>, Vinod Koul <vkoul@kernel.org>,
Bjorn Andersson <bjorn.andersson@linaro.org>
Subject: Re: [PATCH v3 4/5] arm64: dts: qcom: pmm8155au_2: Add base dts file
Date: Fri, 18 Jun 2021 00:32:37 +0200 [thread overview]
Message-ID: <6011130d-8ce8-420b-6e55-5d168fef0347@somainline.org> (raw)
In-Reply-To: <20210617054548.353293-5-bhupesh.sharma@linaro.org>
> Add base DTS file for pmm8155au_2 along with GPIOs, power-on, rtc and vadc
> nodes.
>
> Cc: Mark Brown <broonie@kernel.org>
> Cc: Vinod Koul <vkoul@kernel.org>
> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
> Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
> ---
> arch/arm64/boot/dts/qcom/pmm8155au_2.dtsi | 107 ++++++++++++++++++++++
> 1 file changed, 107 insertions(+)
> create mode 100644 arch/arm64/boot/dts/qcom/pmm8155au_2.dtsi
>
> diff --git a/arch/arm64/boot/dts/qcom/pmm8155au_2.dtsi b/arch/arm64/boot/dts/qcom/pmm8155au_2.dtsi
> new file mode 100644
> index 000000000000..0c7d7a66c0b5
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/pmm8155au_2.dtsi
> @@ -0,0 +1,107 @@
> +// SPDX-License-Identifier: BSD-3-Clause
> +/*
> + * Copyright (c) 2021, Linaro Limited
> + */
> +
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
> +#include <dt-bindings/spmi/spmi.h>
> +
> +/ {
> + thermal-zones {
> + pmm8155au-2-thermal {
> + polling-delay-passive = <100>;
> + polling-delay = <0>;
> +
> + thermal-sensors = <&pmm8155au_2_temp>;
> +
> + trips {
> + trip0 {
> + temperature = <95000>;
> + hysteresis = <0>;
> + type = "passive";
> + };
> +
> + trip1 {
> + temperature = <115000>;
> + hysteresis = <0>;
> + type = "hot";
> + };
> +
> + trip2 {
> + temperature = <145000>;
> + hysteresis = <0>;
> + type = "critical";
> + };
> + };
> + };
> + };
> +};
> +
> +&spmi_bus {
> + pmic@4 {
> + compatible = "qcom,pmm8155au", "qcom,spmi-pmic";
> + reg = <0x4 SPMI_USID>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + power-on@800 {
> + compatible = "qcom,pm8916-pon";
> + reg = <0x0800>;
No common debounce, interrupts, bias- property or pwrkey key code?
Besides, (as a question to Bjorn and others) do we pad reg to 4 digits in PMIC DTs now?
> +
> + status = "disabled";
> + };
> +
> + pmm8155au_2_temp: temp-alarm@2400 {
> + compatible = "qcom,spmi-temp-alarm";
> + reg = <0x2400>;
> + interrupts = <0x4 0x24 0x0 IRQ_TYPE_EDGE_BOTH>;
> + io-channels = <&pmm8155au_2_adc ADC5_DIE_TEMP>;
> + io-channel-names = "thermal";
> + #thermal-sensor-cells = <0>;
> + };
> +
> + pmm8155au_2_adc: adc@3100 {
> + compatible = "qcom,spmi-adc5";
> + reg = <0x3100>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + #io-channel-cells = <1>;
> + interrupts = <0x4 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
> +
> + ref-gnd@0 {
> + reg = <ADC5_REF_GND>;
> + qcom,pre-scaling = <1 1>;
> + label = "ref_gnd";
> + };
> +
> + vref-1p25@1 {
> + reg = <ADC5_1P25VREF>;
> + qcom,pre-scaling = <1 1>;
> + label = "vref_1p25";
> + };
> +
> + die-temp@6 {
> + reg = <ADC5_DIE_TEMP>;
> + qcom,pre-scaling = <1 1>;
> + label = "die_temp";
> + };
> + };
> +
> + pmm8155au_2_gpios: gpio@c000 {
> + compatible = "qcom,pmm8155au-gpio";
> + reg = <0xc000>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
Don't we do gpio-ranges anymore?
> + };
> +
> + pmic@5 {
> + compatible = "qcom,pmm8155au", "qcom,spmi-pmic";
> + reg = <0x5 SPMI_USID>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + };
> +};
Konrad
next prev parent reply other threads:[~2021-06-17 22:32 UTC|newest]
Thread overview: 13+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-06-17 5:45 [PATCH v3 0/5] arm64: dts: qcom: Add SA8155p-adp board DTS Bhupesh Sharma
2021-06-17 5:45 ` [PATCH v3 1/5] dt-bindings: arm: qcom: Add compatible for sm8150-mtp board Bhupesh Sharma
2021-06-17 5:45 ` [PATCH v3 2/5] dt-bindings: arm: qcom: Add compatible for SA8155p-adp board Bhupesh Sharma
2021-06-17 5:45 ` [PATCH v3 3/5] arm64: dts: qcom: pmm8155au_1: Add base dts file Bhupesh Sharma
2021-06-17 22:34 ` Konrad Dybcio
2021-06-18 9:58 ` Bhupesh Sharma
2021-06-17 5:45 ` [PATCH v3 4/5] arm64: dts: qcom: pmm8155au_2: " Bhupesh Sharma
2021-06-17 22:32 ` Konrad Dybcio [this message]
2021-06-18 10:12 ` Bhupesh Sharma
2021-06-18 17:35 ` Bjorn Andersson
2021-06-17 5:45 ` [PATCH v3 5/5] arm64: dts: qcom: sa8155p-adp: " Bhupesh Sharma
2021-06-17 22:26 ` Konrad Dybcio
2021-06-18 9:56 ` Bhupesh Sharma
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=6011130d-8ce8-420b-6e55-5d168fef0347@somainline.org \
--to=konrad.dybcio@somainline.org \
--cc=agross@kernel.org \
--cc=bhupesh.linux@gmail.com \
--cc=bhupesh.sharma@linaro.org \
--cc=bjorn.andersson@linaro.org \
--cc=broonie@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-gpio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=robh+dt@kernel.org \
--cc=vkoul@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).