[PATCH 0/7] Add more DT nodes for Stingray SoC

[PATCH 0/7] Add more DT nodes for Stingray SoC

[Abhishek Shah]

This is round two of adding DT nodes for Stingray SoC.
Corresponding drivers and dt binding documents are already
checked in the kernel and will be present in v4.14.

Abhishek Shah (1):
  arm64: dts: Add DT node to enable BGMAC driver on Stingray

Anup Patel (3):
  arm64: dts: Add sp804 DT nodes for Stingray SoC
  arm64: dts: Add FlexRM DT nodes for Stingray
  arm64: dts: Add SBA-RAID DT nodes for Stingray SoC

Srinath Mannam (2):
  arm64: dts: Add MDIO multiplexer DT node for Stingray
  arm64: dts: Add SATA DT nodes for Stingray SoC

Velibor Markovski (1):
  arm64: dts: Enable stats for CCN-502 interconnect on Stingray

 .../boot/dts/broadcom/stingray/bcm958742-base.dtsi |  78 ++++++
 .../boot/dts/broadcom/stingray/bcm958742k.dts      |   4 +
 .../boot/dts/broadcom/stingray/bcm958742t.dts      |   4 +
 .../boot/dts/broadcom/stingray/stingray-fs4.dtsi   | 118 +++++++++
 .../boot/dts/broadcom/stingray/stingray-sata.dtsi  | 278 +++++++++++++++++++++
 .../arm64/boot/dts/broadcom/stingray/stingray.dtsi | 136 ++++++++++
 6 files changed, 618 insertions(+)
 create mode 100644 arch/arm64/boot/dts/broadcom/stingray/stingray-fs4.dtsi
 create mode 100644 arch/arm64/boot/dts/broadcom/stingray/stingray-sata.dtsi

-- 
2.7.4

[PATCH 1/7] arm64: dts: Enable stats for CCN-502 interconnect on Stingray

[Abhishek Shah]

From: Velibor Markovski <velibor.markovski@broadcom.com>

This patch enables stats for CCN-502 interconnect on Stingray.

Signed-off-by: Velibor Markovski <velibor.markovski@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
---
 arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi b/arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi
index 49933cf..a63c465 100644
--- a/arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi
+++ b/arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi
@@ -152,6 +152,12 @@
 		#size-cells = <1>;
 		ranges = <0x0 0x0 0x61000000 0x05000000>;
 
+		ccn: ccn@00000000 {
+			compatible = "arm,ccn-502";
+			reg = <0x00000000 0x900000>;
+			interrupts = <GIC_SPI 799 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
 		gic: interrupt-controller@02c00000 {
 			compatible = "arm,gic-v3";
 			#interrupt-cells = <3>;
-- 
2.7.4

[PATCH 2/7] arm64: dts: Add MDIO multiplexer DT node for Stingray

[Abhishek Shah]

From: Srinath Mannam <srinath.mannam@broadcom.com>

Added MDIO multiplexer iproc DT node for Stingray, which contains
the child nodes of PCIe serdes, RGMII, SATA and USB phy MDIO slaves.

Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
---
 .../arm64/boot/dts/broadcom/stingray/stingray.dtsi | 31 ++++++++++++++++++++++
 1 file changed, 31 insertions(+)

diff --git a/arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi b/arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi
index a63c465..697401d 100644
--- a/arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi
+++ b/arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi
@@ -275,6 +275,37 @@
 
 		#include "stingray-pinctrl.dtsi"
 
+		mdio_mux_iproc: mdio-mux@0002023c {
+			compatible = "brcm,mdio-mux-iproc";
+			reg = <0x0002023c 0x14>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			mdio@0 { /* PCIe serdes */
+				reg = <0x0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+
+			mdio@2 { /* SATA */
+				reg = <0x2>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+
+			mdio@3 { /* USB */
+				reg = <0x3>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+
+			mdio@10 { /* RGMII */
+				reg = <0x10>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+
 		pwm: pwm@00010000 {
 			compatible = "brcm,iproc-pwm";
 			reg = <0x00010000 0x1000>;
-- 
2.7.4

[PATCH 3/7] arm64: dts: Add sp804 DT nodes for Stingray SoC

[Abhishek Shah]

From: Anup Patel <anup.patel@broadcom.com>

We have 8 instances of sp804 in Stingray SoC. Let's enable
it in Stingray DT.

Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
---
 .../arm64/boot/dts/broadcom/stingray/stingray.dtsi | 87 ++++++++++++++++++++++
 1 file changed, 87 insertions(+)

diff --git a/arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi b/arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi
index 697401d..19ad887 100644
--- a/arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi
+++ b/arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi
@@ -314,6 +314,93 @@
 			status = "disabled";
 		};
 
+		timer0: timer@00030000 {
+			compatible = "arm,sp804", "arm,primecell";
+			reg = <0x00030000 0x1000>;
+			interrupts = <GIC_SPI 179 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&hsls_25m_div2_clk>,
+				 <&hsls_25m_div2_clk>,
+				 <&hsls_div4_clk>;
+			clock-names = "timer1", "timer2", "apb_pclk";
+			status = "disabled";
+		};
+
+		timer1: timer@00040000 {
+			compatible = "arm,sp804", "arm,primecell";
+			reg = <0x00040000 0x1000>;
+			interrupts = <GIC_SPI 180 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&hsls_25m_div2_clk>,
+				 <&hsls_25m_div2_clk>,
+				 <&hsls_div4_clk>;
+			clock-names = "timer1", "timer2", "apb_pclk";
+		};
+
+		timer2: timer@00050000 {
+			compatible = "arm,sp804", "arm,primecell";
+			reg = <0x00050000 0x1000>;
+			interrupts = <GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&hsls_25m_div2_clk>,
+				 <&hsls_25m_div2_clk>,
+				 <&hsls_div4_clk>;
+			clock-names = "timer1", "timer2", "apb_pclk";
+			status = "disabled";
+		};
+
+		timer3: timer@00060000 {
+			compatible = "arm,sp804", "arm,primecell";
+			reg = <0x00060000 0x1000>;
+			interrupts = <GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&hsls_25m_div2_clk>,
+				 <&hsls_25m_div2_clk>,
+				 <&hsls_div4_clk>;
+			clock-names = "timer1", "timer2", "apb_pclk";
+			status = "disabled";
+		};
+
+		timer4: timer@00070000 {
+			compatible = "arm,sp804", "arm,primecell";
+			reg = <0x00070000 0x1000>;
+			interrupts = <GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&hsls_25m_div2_clk>,
+				 <&hsls_25m_div2_clk>,
+				 <&hsls_div4_clk>;
+			clock-names = "timer1", "timer2", "apb_pclk";
+			status = "disabled";
+		};
+
+		timer5: timer@00080000 {
+			compatible = "arm,sp804", "arm,primecell";
+			reg = <0x00080000 0x1000>;
+			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&hsls_25m_div2_clk>,
+				 <&hsls_25m_div2_clk>,
+				 <&hsls_div4_clk>;
+			clock-names = "timer1", "timer2", "apb_pclk";
+			status = "disabled";
+		};
+
+		timer6: timer@00090000 {
+			compatible = "arm,sp804", "arm,primecell";
+			reg = <0x00090000 0x1000>;
+			interrupts = <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&hsls_25m_div2_clk>,
+				 <&hsls_25m_div2_clk>,
+				 <&hsls_div4_clk>;
+			clock-names = "timer1", "timer2", "apb_pclk";
+			status = "disabled";
+		};
+
+		timer7: timer@000a0000 {
+			compatible = "arm,sp804", "arm,primecell";
+			reg = <0x000a0000 0x1000>;
+			interrupts = <GIC_SPI 210 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&hsls_25m_div2_clk>,
+				 <&hsls_25m_div2_clk>,
+				 <&hsls_div4_clk>;
+			clock-names = "timer1", "timer2", "apb_pclk";
+			status = "disabled";
+		};
+
 		i2c0: i2c@000b0000 {
 			compatible = "brcm,iproc-i2c";
 			reg = <0x000b0000 0x100>;
-- 
2.7.4

[PATCH 4/7] arm64: dts: Add DT node to enable BGMAC driver on Stingray

[Abhishek Shah]

This patch adds DT node to enable BGMAC driver on Stingray

Signed-off-by: Abhishek Shah <abhishek.shah@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Oza Oza <oza.oza@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
---
 arch/arm64/boot/dts/broadcom/stingray/bcm958742-base.dtsi | 14 ++++++++++++++
 arch/arm64/boot/dts/broadcom/stingray/bcm958742k.dts      |  4 ++++
 arch/arm64/boot/dts/broadcom/stingray/bcm958742t.dts      |  4 ++++
 arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi       |  9 +++++++++
 4 files changed, 31 insertions(+)

diff --git a/arch/arm64/boot/dts/broadcom/stingray/bcm958742-base.dtsi b/arch/arm64/boot/dts/broadcom/stingray/bcm958742-base.dtsi
index 5dca7d1..cacc25e 100644
--- a/arch/arm64/boot/dts/broadcom/stingray/bcm958742-base.dtsi
+++ b/arch/arm64/boot/dts/broadcom/stingray/bcm958742-base.dtsi
@@ -72,6 +72,14 @@
 	      <0x00000008 0x80000000 0x1 0x80000000>; /* 6G @ 34G */
 };
 
+&mdio_mux_iproc {
+	mdio@10 {
+		gphy0: eth-phy@10 {
+			reg = <0x10>;
+		};
+	};
+};
+
 &uart1 {
 	status = "okay";
 };
@@ -102,6 +110,12 @@
 	};
 };
 
+&enet {
+	phy-mode = "rgmii-id";
+	phy-handle = <&gphy0>;
+	status = "okay";
+};
+
 &nand {
 	status = "ok";
 	nandcs@0 {
diff --git a/arch/arm64/boot/dts/broadcom/stingray/bcm958742k.dts b/arch/arm64/boot/dts/broadcom/stingray/bcm958742k.dts
index 5671669..eb6f08c 100644
--- a/arch/arm64/boot/dts/broadcom/stingray/bcm958742k.dts
+++ b/arch/arm64/boot/dts/broadcom/stingray/bcm958742k.dts
@@ -39,6 +39,10 @@
 	model = "Stingray Combo SVK (BCM958742K)";
 };
 
+&gphy0 {
+	enet-phy-lane-swap;
+};
+
 &uart2 {
 	status = "okay";
 };
diff --git a/arch/arm64/boot/dts/broadcom/stingray/bcm958742t.dts b/arch/arm64/boot/dts/broadcom/stingray/bcm958742t.dts
index 6ebe399..5084b03 100644
--- a/arch/arm64/boot/dts/broadcom/stingray/bcm958742t.dts
+++ b/arch/arm64/boot/dts/broadcom/stingray/bcm958742t.dts
@@ -38,3 +38,7 @@
 	compatible = "brcm,bcm958742t", "brcm,stingray";
 	model = "Stingray SST100 (BCM958742T)";
 };
+
+&gphy0 {
+	enet-phy-lane-swap;
+};
diff --git a/arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi b/arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi
index 19ad887..1c6cc2d 100644
--- a/arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi
+++ b/arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi
@@ -548,6 +548,15 @@
 			iommus = <&smmu 0x6000 0x0000>;
 		};
 
+		enet: ethernet@00340000{
+			compatible = "brcm,amac";
+			reg = <0x00340000 0x1000>;
+			reg-names = "amac_base";
+			dma-coherent;
+			interrupts = <GIC_SPI 213 IRQ_TYPE_LEVEL_HIGH>;
+			status= "disabled";
+		};
+
 		nand: nand@00360000 {
 			compatible = "brcm,nand-iproc", "brcm,brcmnand-v6.1";
 			reg = <0x00360000 0x600>,
-- 
2.7.4

[PATCH 5/7] arm64: dts: Add SATA DT nodes for Stingray SoC

[Abhishek Shah]

From: Srinath Mannam <srinath.mannam@broadcom.com>

Add DT nodes for SATA host controllers and SATA PHYs
on Stingray SoC

Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
---
 .../boot/dts/broadcom/stingray/bcm958742-base.dtsi |  64 +++++
 .../boot/dts/broadcom/stingray/stingray-sata.dtsi  | 278 +++++++++++++++++++++
 .../arm64/boot/dts/broadcom/stingray/stingray.dtsi |   2 +
 3 files changed, 344 insertions(+)
 create mode 100644 arch/arm64/boot/dts/broadcom/stingray/stingray-sata.dtsi

diff --git a/arch/arm64/boot/dts/broadcom/stingray/bcm958742-base.dtsi b/arch/arm64/boot/dts/broadcom/stingray/bcm958742-base.dtsi
index cacc25e..8862ec9 100644
--- a/arch/arm64/boot/dts/broadcom/stingray/bcm958742-base.dtsi
+++ b/arch/arm64/boot/dts/broadcom/stingray/bcm958742-base.dtsi
@@ -72,6 +72,70 @@
 	      <0x00000008 0x80000000 0x1 0x80000000>; /* 6G @ 34G */
 };
 
+&sata0 {
+	status = "okay";
+};
+
+&sata_phy0{
+	status = "okay";
+};
+
+&sata1 {
+	status = "okay";
+};
+
+&sata_phy1{
+	status = "okay";
+};
+
+&sata2 {
+	status = "okay";
+};
+
+&sata_phy2{
+	status = "okay";
+};
+
+&sata3 {
+	status = "okay";
+};
+
+&sata_phy3{
+	status = "okay";
+};
+
+&sata4 {
+	status = "okay";
+};
+
+&sata_phy4{
+	status = "okay";
+};
+
+&sata5 {
+	status = "okay";
+};
+
+&sata_phy5{
+	status = "okay";
+};
+
+&sata6 {
+	status = "okay";
+};
+
+&sata_phy6{
+	status = "okay";
+};
+
+&sata7 {
+	status = "okay";
+};
+
+&sata_phy7{
+	status = "okay";
+};
+
 &mdio_mux_iproc {
 	mdio@10 {
 		gphy0: eth-phy@10 {
diff --git a/arch/arm64/boot/dts/broadcom/stingray/stingray-sata.dtsi b/arch/arm64/boot/dts/broadcom/stingray/stingray-sata.dtsi
new file mode 100644
index 0000000..a774709
--- /dev/null
+++ b/arch/arm64/boot/dts/broadcom/stingray/stingray-sata.dtsi
@@ -0,0 +1,278 @@
+/*
+ *  BSD LICENSE
+ *
+ *  Copyright(c) 2016-2017 Broadcom.  All rights reserved.
+ *
+ *  Redistribution and use in source and binary forms, with or without
+ *  modification, are permitted provided that the following conditions
+ *  are met:
+ *
+ *    * Redistributions of source code must retain the above copyright
+ *      notice, this list of conditions and the following disclaimer.
+ *    * Redistributions in binary form must reproduce the above copyright
+ *      notice, this list of conditions and the following disclaimer in
+ *      the documentation and/or other materials provided with the
+ *      distribution.
+ *    * Neither the name of Broadcom nor the names of its
+ *      contributors may be used to endorse or promote products derived
+ *      from this software without specific prior written permission.
+ *
+ *  THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ *  "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ *  LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+ *  A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ *  OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+ *  SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ *  LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+ *  DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+ *  THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ *  OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+	sata {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x0 0x67d00000 0x00800000>;
+
+		sata0: ahci@00210000 {
+			compatible = "brcm,iproc-ahci", "generic-ahci";
+			reg = <0x00210000 0x1000>;
+			reg-names = "ahci";
+			interrupts = <GIC_SPI 339 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			sata0_port0: sata-port@0 {
+				reg = <0>;
+				phys = <&sata0_phy0>;
+				phy-names = "sata-phy";
+			};
+		};
+
+		sata_phy0: sata_phy@00212100 {
+			compatible = "brcm,iproc-sr-sata-phy";
+			reg = <0x00212100 0x1000>;
+			reg-names = "phy";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			sata0_phy0: sata-phy@0 {
+				reg = <0>;
+				#phy-cells = <0>;
+			};
+		};
+
+		sata1: ahci@00310000 {
+			compatible = "brcm,iproc-ahci", "generic-ahci";
+			reg = <0x00310000 0x1000>;
+			reg-names = "ahci";
+			interrupts = <GIC_SPI 347 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			sata1_port0: sata-port@0 {
+				reg = <0>;
+				phys = <&sata1_phy0>;
+				phy-names = "sata-phy";
+			};
+		};
+
+		sata_phy1: sata_phy@00312100 {
+			compatible = "brcm,iproc-sr-sata-phy";
+			reg = <0x00312100 0x1000>;
+			reg-names = "phy";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			sata1_phy0: sata-phy@0 {
+				reg = <0>;
+				#phy-cells = <0>;
+			};
+		};
+
+		sata2: ahci@00120000 {
+			compatible = "brcm,iproc-ahci", "generic-ahci";
+			reg = <0x00120000 0x1000>;
+			reg-names = "ahci";
+			interrupts = <GIC_SPI 333 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			sata2_port0: sata-port@0 {
+				reg = <0>;
+				phys = <&sata2_phy0>;
+				phy-names = "sata-phy";
+			};
+		};
+
+		sata_phy2: sata_phy@00122100 {
+			compatible = "brcm,iproc-sr-sata-phy";
+			reg = <0x00122100 0x1000>;
+			reg-names = "phy";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			sata2_phy0: sata-phy@0 {
+				reg = <0>;
+				#phy-cells = <0>;
+			};
+		};
+
+		sata3: ahci@00130000 {
+			compatible = "brcm,iproc-ahci", "generic-ahci";
+			reg = <0x00130000 0x1000>;
+			reg-names = "ahci";
+			interrupts = <GIC_SPI 335 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			sata3_port0: sata-port@0 {
+				reg = <0>;
+				phys = <&sata3_phy0>;
+				phy-names = "sata-phy";
+			};
+		};
+
+		sata_phy3: sata_phy@00132100 {
+			compatible = "brcm,iproc-sr-sata-phy";
+			reg = <0x00132100 0x1000>;
+			reg-names = "phy";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			sata3_phy0: sata-phy@0 {
+				reg = <0>;
+				#phy-cells = <0>;
+			};
+		};
+
+		sata4: ahci@00330000 {
+			compatible = "brcm,iproc-ahci", "generic-ahci";
+			reg = <0x00330000 0x1000>;
+			reg-names = "ahci";
+			interrupts = <GIC_SPI 351 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			sata4_port0: sata-port@0 {
+				reg = <0>;
+				phys = <&sata4_phy0>;
+				phy-names = "sata-phy";
+			};
+		};
+
+		sata_phy4: sata_phy@00332100 {
+			compatible = "brcm,iproc-sr-sata-phy";
+			reg = <0x00332100 0x1000>;
+			reg-names = "phy";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			sata4_phy0: sata-phy@0 {
+				reg = <0>;
+				#phy-cells = <0>;
+			};
+		};
+
+		sata5: ahci@00400000 {
+			compatible = "brcm,iproc-ahci", "generic-ahci";
+			reg = <0x00400000 0x1000>;
+			reg-names = "ahci";
+			interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			sata5_port0: sata-port@0 {
+				reg = <0>;
+				phys = <&sata5_phy0>;
+				phy-names = "sata-phy";
+			};
+		};
+
+		sata_phy5: sata_phy@00402100 {
+			compatible = "brcm,iproc-sr-sata-phy";
+			reg = <0x00402100 0x1000>;
+			reg-names = "phy";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			sata5_phy0: sata-phy@0 {
+				reg = <0>;
+				#phy-cells = <0>;
+			};
+		};
+
+		sata6: ahci@00410000 {
+			compatible = "brcm,iproc-ahci", "generic-ahci";
+			reg = <0x00410000 0x1000>;
+			reg-names = "ahci";
+			interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			sata6_port0: sata-port@0 {
+				reg = <0>;
+				phys = <&sata6_phy0>;
+				phy-names = "sata-phy";
+			};
+		};
+
+		sata_phy6: sata_phy@00412100 {
+			compatible = "brcm,iproc-sr-sata-phy";
+			reg = <0x00412100 0x1000>;
+			reg-names = "phy";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			sata6_phy0: sata-phy@0 {
+				reg = <0>;
+				#phy-cells = <0>;
+			};
+		};
+
+		sata7: ahci@00420000 {
+			compatible = "brcm,iproc-ahci", "generic-ahci";
+			reg = <0x00420000 0x1000>;
+			reg-names = "ahci";
+			interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			sata7_port0: sata-port@0 {
+				reg = <0>;
+				phys = <&sata7_phy0>;
+				phy-names = "sata-phy";
+			};
+		};
+
+		sata_phy7: sata_phy@00422100 {
+			compatible = "brcm,iproc-sr-sata-phy";
+			reg = <0x00422100 0x1000>;
+			reg-names = "phy";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			sata7_phy0: sata-phy@0 {
+				reg = <0>;
+				#phy-cells = <0>;
+			};
+		};
+	};
diff --git a/arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi b/arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi
index 1c6cc2d..1700033 100644
--- a/arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi
+++ b/arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi
@@ -267,6 +267,8 @@
 		};
 	};
 
+	#include "stingray-sata.dtsi"
+
 	hsls {
 		compatible = "simple-bus";
 		#address-cells = <1>;
-- 
2.7.4

[PATCH 6/7] arm64: dts: Add FlexRM DT nodes for Stingray

[Abhishek Shah]

From: Anup Patel <anup.patel@broadcom.com>

We have two instances of FlexRM on Stingray. One for SBA RAID
offload engine and another for SPU2 Crypto offload engine.

This patch adds FlexRM mailbox controller DT nodes for Stingray.

Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Signed-off-by: Raveendra Padasalagi <raveendra.padasalagi@broadcom.com>
---
 .../boot/dts/broadcom/stingray/stingray-fs4.dtsi   | 54 ++++++++++++++++++++++
 .../arm64/boot/dts/broadcom/stingray/stingray.dtsi |  1 +
 2 files changed, 55 insertions(+)
 create mode 100644 arch/arm64/boot/dts/broadcom/stingray/stingray-fs4.dtsi

diff --git a/arch/arm64/boot/dts/broadcom/stingray/stingray-fs4.dtsi b/arch/arm64/boot/dts/broadcom/stingray/stingray-fs4.dtsi
new file mode 100644
index 0000000..1f927c4
--- /dev/null
+++ b/arch/arm64/boot/dts/broadcom/stingray/stingray-fs4.dtsi
@@ -0,0 +1,54 @@
+/*
+ *  BSD LICENSE
+ *
+ *  Copyright(c) 2016-2017 Broadcom.  All rights reserved.
+ *
+ *  Redistribution and use in source and binary forms, with or without
+ *  modification, are permitted provided that the following conditions
+ *  are met:
+ *
+ *    * Redistributions of source code must retain the above copyright
+ *      notice, this list of conditions and the following disclaimer.
+ *    * Redistributions in binary form must reproduce the above copyright
+ *      notice, this list of conditions and the following disclaimer in
+ *      the documentation and/or other materials provided with the
+ *      distribution.
+ *    * Neither the name of Broadcom nor the names of its
+ *      contributors may be used to endorse or promote products derived
+ *      from this software without specific prior written permission.
+ *
+ *  THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ *  "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ *  LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
+ *  A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
+ *  OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
+ *  SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
+ *  LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
+ *  DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
+ *  THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ *  OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+	fs4: fs4 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x0 0x67000000 0x00800000>;
+
+		crypto_mbox: crypto_mbox@00000000 {
+			compatible = "brcm,iproc-flexrm-mbox";
+			reg = <0x00000000 0x200000>;
+			msi-parent = <&gic_its 0x4100>;
+			#mbox-cells = <3>;
+			dma-coherent;
+		};
+
+		raid_mbox: raid_mbox@00400000 {
+			compatible = "brcm,iproc-flexrm-mbox";
+			reg = <0x00400000 0x200000>;
+			dma-coherent;
+			msi-parent = <&gic_its 0x4300>;
+			#mbox-cells = <3>;
+		};
+	};
diff --git a/arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi b/arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi
index 1700033..e6f75c6 100644
--- a/arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi
+++ b/arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi
@@ -267,6 +267,7 @@
 		};
 	};
 
+	#include "stingray-fs4.dtsi"
 	#include "stingray-sata.dtsi"
 
 	hsls {
-- 
2.7.4

[PATCH 7/7] arm64: dts: Add SBA-RAID DT nodes for Stingray SoC

[Abhishek Shah]

From: Anup Patel <anup.patel@broadcom.com>

This patch adds Broadcom SBA-RAID DT nodes for Stingray SoC.

The Stingray SoC has total 32 SBA-RAID FlexRM rings and it has
8 CPUs so we create 8 SBA-RAID instances (one for each CPU).
This way Linux DMAENGINE will have one SBA-RAID DMA device for
each CPU.

Signed-off-by: Anup Patel <anup.patel@broadcom.com>
---
 .../boot/dts/broadcom/stingray/stingray-fs4.dtsi   | 64 ++++++++++++++++++++++
 1 file changed, 64 insertions(+)

diff --git a/arch/arm64/boot/dts/broadcom/stingray/stingray-fs4.dtsi b/arch/arm64/boot/dts/broadcom/stingray/stingray-fs4.dtsi
index 1f927c4..8bf1dc6 100644
--- a/arch/arm64/boot/dts/broadcom/stingray/stingray-fs4.dtsi
+++ b/arch/arm64/boot/dts/broadcom/stingray/stingray-fs4.dtsi
@@ -51,4 +51,68 @@
 			msi-parent = <&gic_its 0x4300>;
 			#mbox-cells = <3>;
 		};
+
+		raid0: raid@0 {
+			compatible = "brcm,iproc-sba-v2";
+			mboxes = <&raid_mbox 0 0x1 0xff00>,
+				 <&raid_mbox 1 0x1 0xff00>,
+				 <&raid_mbox 2 0x1 0xff00>,
+				 <&raid_mbox 3 0x1 0xff00>;
+		};
+
+		raid1: raid@1 {
+			compatible = "brcm,iproc-sba-v2";
+			mboxes = <&raid_mbox 4 0x1 0xff00>,
+				 <&raid_mbox 5 0x1 0xff00>,
+				 <&raid_mbox 6 0x1 0xff00>,
+				 <&raid_mbox 7 0x1 0xff00>;
+		};
+
+		raid2: raid@2 {
+			compatible = "brcm,iproc-sba-v2";
+			mboxes = <&raid_mbox 8 0x1 0xff00>,
+				 <&raid_mbox 9 0x1 0xff00>,
+				 <&raid_mbox 10 0x1 0xff00>,
+				 <&raid_mbox 11 0x1 0xff00>;
+		};
+
+		raid3: raid@3 {
+			compatible = "brcm,iproc-sba-v2";
+			mboxes = <&raid_mbox 12 0x1 0xff00>,
+				 <&raid_mbox 13 0x1 0xff00>,
+				 <&raid_mbox 14 0x1 0xff00>,
+				 <&raid_mbox 15 0x1 0xff00>;
+		};
+
+		raid4: raid@4 {
+			compatible = "brcm,iproc-sba-v2";
+			mboxes = <&raid_mbox 16 0x1 0xff00>,
+				 <&raid_mbox 17 0x1 0xff00>,
+				 <&raid_mbox 18 0x1 0xff00>,
+				 <&raid_mbox 19 0x1 0xff00>;
+		};
+
+		raid5: raid@5 {
+			compatible = "brcm,iproc-sba-v2";
+			mboxes = <&raid_mbox 20 0x1 0xff00>,
+				 <&raid_mbox 21 0x1 0xff00>,
+				 <&raid_mbox 22 0x1 0xff00>,
+				 <&raid_mbox 23 0x1 0xff00>;
+		};
+
+		raid6: raid@6 {
+			compatible = "brcm,iproc-sba-v2";
+			mboxes = <&raid_mbox 24 0x1 0xff00>,
+				 <&raid_mbox 25 0x1 0xff00>,
+				 <&raid_mbox 26 0x1 0xff00>,
+				 <&raid_mbox 27 0x1 0xff00>;
+		};
+
+		raid7: raid@7 {
+			compatible = "brcm,iproc-sba-v2";
+			mboxes = <&raid_mbox 28 0x1 0xff00>,
+				 <&raid_mbox 29 0x1 0xff00>,
+				 <&raid_mbox 30 0x1 0xff00>,
+				 <&raid_mbox 31 0x1 0xff00>;
+		};
 	};
-- 
2.7.4

Re: [PATCH 0/7] Add more DT nodes for Stingray SoC

[Florian Fainelli]

On 07/28/2017 09:42 PM, Abhishek Shah wrote:
> This is round two of adding DT nodes for Stingray SoC.
> Corresponding drivers and dt binding documents are already
> checked in the kernel and will be present in v4.14.
> 
> Abhishek Shah (1):
>   arm64: dts: Add DT node to enable BGMAC driver on Stingray
> 
> Anup Patel (3):
>   arm64: dts: Add sp804 DT nodes for Stingray SoC
>   arm64: dts: Add FlexRM DT nodes for Stingray
>   arm64: dts: Add SBA-RAID DT nodes for Stingray SoC
> 
> Srinath Mannam (2):
>   arm64: dts: Add MDIO multiplexer DT node for Stingray
>   arm64: dts: Add SATA DT nodes for Stingray SoC
> 
> Velibor Markovski (1):
>   arm64: dts: Enable stats for CCN-502 interconnect on Stingray

Series applied, thanks
-- 
Florian