* [PATCH v2 1/2] dt-bindings: regulator: Add Spreadtrum SC2731 regulator documentation
@ 2017-12-05 6:35 Erick Chen
2017-12-05 6:35 ` [PATCH v2 2/2] regulator: sc2731: Add regulator driver to support Spreadtrum SC2731 PMIC Erick Chen
2017-12-05 12:48 ` Applied "regulator: Add Spreadtrum SC2731 regulator documentation" " Mark Brown
0 siblings, 2 replies; 4+ messages in thread
From: Erick Chen @ 2017-12-05 6:35 UTC (permalink / raw)
To: broonie, robh+dt, mark.rutland, lgirdwood
Cc: linux-kernel, devicetree, baolin.wang, baolin.wang, erick.chen
This patch adds support for the Spreadtrum SC2731
voltage regulator device.
Signed-off-by: Erick Chen <erick.chen@spreadtrum.com>
---
Changes since v1:
- Remove reg property.
- Remove regulators sub-node.
---
.../bindings/regulator/sprd,sc2731-regulator.txt | 43 ++++++++++++++++++++
1 file changed, 43 insertions(+)
create mode 100644 Documentation/devicetree/bindings/regulator/sprd,sc2731-regulator.txt
diff --git a/Documentation/devicetree/bindings/regulator/sprd,sc2731-regulator.txt b/Documentation/devicetree/bindings/regulator/sprd,sc2731-regulator.txt
new file mode 100644
index 0000000..63dc078
--- /dev/null
+++ b/Documentation/devicetree/bindings/regulator/sprd,sc2731-regulator.txt
@@ -0,0 +1,43 @@
+Spreadtrum SC2731 Voltage regulators
+
+The SC2731 integrates low-voltage and low quiescent current DCDC/LDO.
+14 LDO and 3 DCDCs are designed for external use. All DCDCs/LDOs have
+their own bypass (power-down) control signals. External tantalum or MLCC
+ceramic capacitors are recommended to use with these LDOs.
+
+Required properties:
+ - compatible: should be "sprd,sc27xx-regulator".
+
+List of regulators provided by this controller. It is named according to
+its regulator type, BUCK_<name> and LDO_<name>. The definition for each
+of these nodes is defined using the standard binding for regulators at
+Documentation/devicetree/bindings/regulator/regulator.txt.
+
+The valid names for regulators are:
+BUCK:
+ BUCK_CPU0, BUCK_CPU1, BUCK_RF
+LDO:
+ LDO_CAMA0, LDO_CAMA1, LDO_CAMMOT, LDO_VLDO, LDO_EMMCCORE, LDO_SDCORE,
+ LDO_SDIO, LDO_WIFIPA, LDO_USB33, LDO_CAMD0, LDO_CAMD1, LDO_CON,
+ LDO_CAMIO, LDO_SRAM
+
+Example:
+ regulators {
+ compatible = "sprd,sc27xx-regulator";
+
+ vddarm0: BUCK_CPU0 {
+ regulator-name = "vddarm0";
+ regulator-min-microvolt = <400000>;
+ regulator-max-microvolt = <1996875>;
+ regulator-ramp-delay = <25000>;
+ regulator-always-on;
+ };
+
+ vddcama0: LDO_CAMA0 {
+ regulator-name = "vddcama0";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <3750000>;
+ regulator-enable-ramp-delay = <100>;
+ };
+ ...
+ };
--
1.7.9.5
^ permalink raw reply related [flat|nested] 4+ messages in thread
* [PATCH v2 2/2] regulator: sc2731: Add regulator driver to support Spreadtrum SC2731 PMIC
2017-12-05 6:35 [PATCH v2 1/2] dt-bindings: regulator: Add Spreadtrum SC2731 regulator documentation Erick Chen
@ 2017-12-05 6:35 ` Erick Chen
2017-12-05 12:48 ` Applied "regulator: sc2731: Add regulator driver to support Spreadtrum SC2731 PMIC" to the regulator tree Mark Brown
2017-12-05 12:48 ` Applied "regulator: Add Spreadtrum SC2731 regulator documentation" " Mark Brown
1 sibling, 1 reply; 4+ messages in thread
From: Erick Chen @ 2017-12-05 6:35 UTC (permalink / raw)
To: broonie, robh+dt, mark.rutland, lgirdwood
Cc: linux-kernel, devicetree, baolin.wang, baolin.wang, erick.chen
Add regulator driver for Spreadtrum SC2731 device.
It has 17 general purpose LDOs, BUCKs generator and
digital output to control regulators.
Signed-off-by: Erick Chen <erick.chen@spreadtrum.com>
Reviewed-by: Baolin Wang <baolin.wang@spreadtrum.com>
---
Changes since v1:
- Remove of_device_id table.
- Change subsys_init() to module_init().
- Change the file's license format.
---
drivers/regulator/Kconfig | 7 +
drivers/regulator/Makefile | 1 +
drivers/regulator/sc2731-regulator.c | 256 ++++++++++++++++++++++++++++++++++
3 files changed, 264 insertions(+)
create mode 100644 drivers/regulator/sc2731-regulator.c
diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index 96cd55f..b27417c 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -744,6 +744,13 @@ config REGULATOR_S5M8767
via I2C bus. S5M8767A have 9 Bucks and 28 LDOs output and
supports DVS mode with 8bits of output voltage control.
+config REGULATOR_SC2731
+ tristate "Spreadtrum SC2731 power regulator driver"
+ depends on MFD_SC27XX_PMIC || COMPILE_TEST
+ help
+ This driver provides support for the voltage regulators on the
+ SC2731 PMIC.
+
config REGULATOR_SKY81452
tristate "Skyworks Solutions SKY81452 voltage regulator"
depends on MFD_SKY81452
diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
index 80ffc57..19fea09 100644
--- a/drivers/regulator/Makefile
+++ b/drivers/regulator/Makefile
@@ -95,6 +95,7 @@ obj-$(CONFIG_REGULATOR_RT5033) += rt5033-regulator.o
obj-$(CONFIG_REGULATOR_S2MPA01) += s2mpa01.o
obj-$(CONFIG_REGULATOR_S2MPS11) += s2mps11.o
obj-$(CONFIG_REGULATOR_S5M8767) += s5m8767.o
+obj-$(CONFIG_REGULATOR_SC2731) += sc2731-regulator.o
obj-$(CONFIG_REGULATOR_SKY81452) += sky81452-regulator.o
obj-$(CONFIG_REGULATOR_STM32_VREFBUF) += stm32-vrefbuf.o
obj-$(CONFIG_REGULATOR_STW481X_VMMC) += stw481x-vmmc.o
diff --git a/drivers/regulator/sc2731-regulator.c b/drivers/regulator/sc2731-regulator.c
new file mode 100644
index 0000000..794fcd5
--- /dev/null
+++ b/drivers/regulator/sc2731-regulator.c
@@ -0,0 +1,256 @@
+ //SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2017 Spreadtrum Communications Inc.
+ */
+
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/of_regulator.h>
+
+/*
+ * SC2731 regulator lock register
+ */
+#define SC2731_PWR_WR_PROT_VALUE 0xf0c
+#define SC2731_WR_UNLOCK 0x6e7f
+
+/*
+ * SC2731 enable register
+ */
+#define SC2731_POWER_PD_SW 0xc28
+#define SC2731_LDO_CAMA0_PD 0xcfc
+#define SC2731_LDO_CAMA1_PD 0xd04
+#define SC2731_LDO_CAMMOT_PD 0xd0c
+#define SC2731_LDO_VLDO_PD 0xd6c
+#define SC2731_LDO_EMMCCORE_PD 0xd2c
+#define SC2731_LDO_SDCORE_PD 0xd74
+#define SC2731_LDO_SDIO_PD 0xd70
+#define SC2731_LDO_WIFIPA_PD 0xd4c
+#define SC2731_LDO_USB33_PD 0xd5c
+#define SC2731_LDO_CAMD0_PD 0xd7c
+#define SC2731_LDO_CAMD1_PD 0xd84
+#define SC2731_LDO_CON_PD 0xd8c
+#define SC2731_LDO_CAMIO_PD 0xd94
+#define SC2731_LDO_SRAM_PD 0xd78
+
+/*
+ * SC2731 enable mask
+ */
+#define SC2731_DCDC_CPU0_PD_MASK BIT(4)
+#define SC2731_DCDC_CPU1_PD_MASK BIT(3)
+#define SC2731_DCDC_RF_PD_MASK BIT(11)
+#define SC2731_LDO_CAMA0_PD_MASK BIT(0)
+#define SC2731_LDO_CAMA1_PD_MASK BIT(0)
+#define SC2731_LDO_CAMMOT_PD_MASK BIT(0)
+#define SC2731_LDO_VLDO_PD_MASK BIT(0)
+#define SC2731_LDO_EMMCCORE_PD_MASK BIT(0)
+#define SC2731_LDO_SDCORE_PD_MASK BIT(0)
+#define SC2731_LDO_SDIO_PD_MASK BIT(0)
+#define SC2731_LDO_WIFIPA_PD_MASK BIT(0)
+#define SC2731_LDO_USB33_PD_MASK BIT(0)
+#define SC2731_LDO_CAMD0_PD_MASK BIT(0)
+#define SC2731_LDO_CAMD1_PD_MASK BIT(0)
+#define SC2731_LDO_CON_PD_MASK BIT(0)
+#define SC2731_LDO_CAMIO_PD_MASK BIT(0)
+#define SC2731_LDO_SRAM_PD_MASK BIT(0)
+
+/*
+ * SC2731 vsel register
+ */
+#define SC2731_DCDC_CPU0_VOL 0xc54
+#define SC2731_DCDC_CPU1_VOL 0xc64
+#define SC2731_DCDC_RF_VOL 0xcb8
+#define SC2731_LDO_CAMA0_VOL 0xd00
+#define SC2731_LDO_CAMA1_VOL 0xd08
+#define SC2731_LDO_CAMMOT_VOL 0xd10
+#define SC2731_LDO_VLDO_VOL 0xd28
+#define SC2731_LDO_EMMCCORE_VOL 0xd30
+#define SC2731_LDO_SDCORE_VOL 0xd38
+#define SC2731_LDO_SDIO_VOL 0xd40
+#define SC2731_LDO_WIFIPA_VOL 0xd50
+#define SC2731_LDO_USB33_VOL 0xd60
+#define SC2731_LDO_CAMD0_VOL 0xd80
+#define SC2731_LDO_CAMD1_VOL 0xd88
+#define SC2731_LDO_CON_VOL 0xd90
+#define SC2731_LDO_CAMIO_VOL 0xd98
+#define SC2731_LDO_SRAM_VOL 0xdB0
+
+/*
+ * SC2731 vsel register mask
+ */
+#define SC2731_DCDC_CPU0_VOL_MASK GENMASK(8, 0)
+#define SC2731_DCDC_CPU1_VOL_MASK GENMASK(8, 0)
+#define SC2731_DCDC_RF_VOL_MASK GENMASK(8, 0)
+#define SC2731_LDO_CAMA0_VOL_MASK GENMASK(7, 0)
+#define SC2731_LDO_CAMA1_VOL_MASK GENMASK(7, 0)
+#define SC2731_LDO_CAMMOT_VOL_MASK GENMASK(7, 0)
+#define SC2731_LDO_VLDO_VOL_MASK GENMASK(7, 0)
+#define SC2731_LDO_EMMCCORE_VOL_MASK GENMASK(7, 0)
+#define SC2731_LDO_SDCORE_VOL_MASK GENMASK(7, 0)
+#define SC2731_LDO_SDIO_VOL_MASK GENMASK(7, 0)
+#define SC2731_LDO_WIFIPA_VOL_MASK GENMASK(7, 0)
+#define SC2731_LDO_USB33_VOL_MASK GENMASK(7, 0)
+#define SC2731_LDO_CAMD0_VOL_MASK GENMASK(6, 0)
+#define SC2731_LDO_CAMD1_VOL_MASK GENMASK(6, 0)
+#define SC2731_LDO_CON_VOL_MASK GENMASK(6, 0)
+#define SC2731_LDO_CAMIO_VOL_MASK GENMASK(6, 0)
+#define SC2731_LDO_SRAM_VOL_MASK GENMASK(6, 0)
+
+enum sc2731_regulator_id {
+ SC2731_BUCK_CPU0,
+ SC2731_BUCK_CPU1,
+ SC2731_BUCK_RF,
+ SC2731_LDO_CAMA0,
+ SC2731_LDO_CAMA1,
+ SC2731_LDO_CAMMOT,
+ SC2731_LDO_VLDO,
+ SC2731_LDO_EMMCCORE,
+ SC2731_LDO_SDCORE,
+ SC2731_LDO_SDIO,
+ SC2731_LDO_WIFIPA,
+ SC2731_LDO_USB33,
+ SC2731_LDO_CAMD0,
+ SC2731_LDO_CAMD1,
+ SC2731_LDO_CON,
+ SC2731_LDO_CAMIO,
+ SC2731_LDO_SRAM,
+};
+
+static const struct regulator_ops sc2731_regu_linear_ops = {
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .is_enabled = regulator_is_enabled_regmap,
+ .list_voltage = regulator_list_voltage_linear,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+ .set_voltage_sel = regulator_set_voltage_sel_regmap,
+};
+
+#define SC2731_REGU_LINEAR(_id, en_reg, en_mask, vreg, vmask, \
+ vstep, vmin, vmax) { \
+ .name = #_id, \
+ .of_match = of_match_ptr(#_id), \
+ .ops = &sc2731_regu_linear_ops, \
+ .type = REGULATOR_VOLTAGE, \
+ .id = SC2731_##_id, \
+ .owner = THIS_MODULE, \
+ .min_uV = vmin, \
+ .n_voltages = ((vmax) - (vmin)) / (vstep) + 1, \
+ .uV_step = vstep, \
+ .enable_is_inverted = true, \
+ .enable_val = 0, \
+ .enable_reg = en_reg, \
+ .enable_mask = en_mask, \
+ .vsel_reg = vreg, \
+ .vsel_mask = vmask, \
+}
+
+static struct regulator_desc regulators[] = {
+ SC2731_REGU_LINEAR(BUCK_CPU0, SC2731_POWER_PD_SW,
+ SC2731_DCDC_CPU0_PD_MASK, SC2731_DCDC_CPU0_VOL,
+ SC2731_DCDC_CPU0_VOL_MASK, 3125, 400000, 1996875),
+ SC2731_REGU_LINEAR(BUCK_CPU1, SC2731_POWER_PD_SW,
+ SC2731_DCDC_CPU1_PD_MASK, SC2731_DCDC_CPU1_VOL,
+ SC2731_DCDC_CPU1_VOL_MASK, 3125, 400000, 1996875),
+ SC2731_REGU_LINEAR(BUCK_RF, SC2731_POWER_PD_SW, SC2731_DCDC_RF_PD_MASK,
+ SC2731_DCDC_RF_VOL, SC2731_DCDC_RF_VOL_MASK,
+ 3125, 600000, 2196875),
+ SC2731_REGU_LINEAR(LDO_CAMA0, SC2731_LDO_CAMA0_PD,
+ SC2731_LDO_CAMA0_PD_MASK, SC2731_LDO_CAMA0_VOL,
+ SC2731_LDO_CAMA0_VOL_MASK, 10000, 1200000, 3750000),
+ SC2731_REGU_LINEAR(LDO_CAMA1, SC2731_LDO_CAMA1_PD,
+ SC2731_LDO_CAMA1_PD_MASK, SC2731_LDO_CAMA1_VOL,
+ SC2731_LDO_CAMA1_VOL_MASK, 10000, 1200000, 3750000),
+ SC2731_REGU_LINEAR(LDO_CAMMOT, SC2731_LDO_CAMMOT_PD,
+ SC2731_LDO_CAMMOT_PD_MASK, SC2731_LDO_CAMMOT_VOL,
+ SC2731_LDO_CAMMOT_VOL_MASK, 10000, 1200000, 3750000),
+ SC2731_REGU_LINEAR(LDO_VLDO, SC2731_LDO_VLDO_PD,
+ SC2731_LDO_VLDO_PD_MASK, SC2731_LDO_VLDO_VOL,
+ SC2731_LDO_VLDO_VOL_MASK, 10000, 1200000, 3750000),
+ SC2731_REGU_LINEAR(LDO_EMMCCORE, SC2731_LDO_EMMCCORE_PD,
+ SC2731_LDO_EMMCCORE_PD_MASK, SC2731_LDO_EMMCCORE_VOL,
+ SC2731_LDO_EMMCCORE_VOL_MASK, 10000, 1200000,
+ 3750000),
+ SC2731_REGU_LINEAR(LDO_SDCORE, SC2731_LDO_SDCORE_PD,
+ SC2731_LDO_SDCORE_PD_MASK, SC2731_LDO_SDCORE_VOL,
+ SC2731_LDO_SDCORE_VOL_MASK, 10000, 1200000, 3750000),
+ SC2731_REGU_LINEAR(LDO_SDIO, SC2731_LDO_SDIO_PD,
+ SC2731_LDO_SDIO_PD_MASK, SC2731_LDO_SDIO_VOL,
+ SC2731_LDO_SDIO_VOL_MASK, 10000, 1200000, 3750000),
+ SC2731_REGU_LINEAR(LDO_WIFIPA, SC2731_LDO_WIFIPA_PD,
+ SC2731_LDO_WIFIPA_PD_MASK, SC2731_LDO_WIFIPA_VOL,
+ SC2731_LDO_WIFIPA_VOL_MASK, 10000, 1200000, 3750000),
+ SC2731_REGU_LINEAR(LDO_USB33, SC2731_LDO_USB33_PD,
+ SC2731_LDO_USB33_PD_MASK, SC2731_LDO_USB33_VOL,
+ SC2731_LDO_USB33_VOL_MASK, 10000, 1200000, 3750000),
+ SC2731_REGU_LINEAR(LDO_CAMD0, SC2731_LDO_CAMD0_PD,
+ SC2731_LDO_CAMD0_PD_MASK, SC2731_LDO_CAMD0_VOL,
+ SC2731_LDO_CAMD0_VOL_MASK, 6250, 1000000, 1793750),
+ SC2731_REGU_LINEAR(LDO_CAMD1, SC2731_LDO_CAMD1_PD,
+ SC2731_LDO_CAMD1_PD_MASK, SC2731_LDO_CAMD1_VOL,
+ SC2731_LDO_CAMD1_VOL_MASK, 6250, 1000000, 1793750),
+ SC2731_REGU_LINEAR(LDO_CON, SC2731_LDO_CON_PD,
+ SC2731_LDO_CON_PD_MASK, SC2731_LDO_CON_VOL,
+ SC2731_LDO_CON_VOL_MASK, 6250, 1000000, 1793750),
+ SC2731_REGU_LINEAR(LDO_CAMIO, SC2731_LDO_CAMIO_PD,
+ SC2731_LDO_CAMIO_PD_MASK, SC2731_LDO_CAMIO_VOL,
+ SC2731_LDO_CAMIO_VOL_MASK, 6250, 1000000, 1793750),
+ SC2731_REGU_LINEAR(LDO_SRAM, SC2731_LDO_SRAM_PD,
+ SC2731_LDO_SRAM_PD_MASK, SC2731_LDO_SRAM_VOL,
+ SC2731_LDO_SRAM_VOL_MASK, 6250, 1000000, 1793750),
+};
+
+static int sc2731_regulator_unlock(struct regmap *regmap)
+{
+ return regmap_write(regmap, SC2731_PWR_WR_PROT_VALUE,
+ SC2731_WR_UNLOCK);
+}
+
+static int sc2731_regulator_probe(struct platform_device *pdev)
+{
+ int i, ret;
+ struct regmap *regmap;
+ struct regulator_config config = { };
+ struct regulator_dev *rdev;
+
+ regmap = dev_get_regmap(pdev->dev.parent, NULL);
+ if (!regmap) {
+ dev_err(&pdev->dev, "failed to get regmap.\n");
+ return -ENODEV;
+ }
+
+ ret = sc2731_regulator_unlock(regmap);
+ if (ret) {
+ dev_err(&pdev->dev, "failed to release regulator lock\n");
+ return ret;
+ }
+
+ config.dev = &pdev->dev;
+ config.regmap = regmap;
+
+ for (i = 0; i < ARRAY_SIZE(regulators); i++) {
+ rdev = devm_regulator_register(&pdev->dev, ®ulators[i],
+ &config);
+ if (IS_ERR(rdev)) {
+ dev_err(&pdev->dev, "failed to register regulator %s\n",
+ regulators[i].name);
+ return PTR_ERR(rdev);
+ }
+ }
+
+ return 0;
+}
+
+static struct platform_driver sc2731_regulator_driver = {
+ .driver = {
+ .name = "sc27xx-regulator",
+ },
+ .probe = sc2731_regulator_probe,
+};
+
+module_platform_driver(sc2731_regulator_driver);
+
+MODULE_AUTHOR("Chen Junhui <erick.chen@spreadtrum.com>");
+MODULE_DESCRIPTION("Spreadtrum SC2731 regulator driver");
+MODULE_LICENSE("GPL v2");
--
1.7.9.5
^ permalink raw reply related [flat|nested] 4+ messages in thread
* Applied "regulator: sc2731: Add regulator driver to support Spreadtrum SC2731 PMIC" to the regulator tree
2017-12-05 6:35 ` [PATCH v2 2/2] regulator: sc2731: Add regulator driver to support Spreadtrum SC2731 PMIC Erick Chen
@ 2017-12-05 12:48 ` Mark Brown
0 siblings, 0 replies; 4+ messages in thread
From: Mark Brown @ 2017-12-05 12:48 UTC (permalink / raw)
To: Erick Chen
Cc: Mark Brown, broonie, robh+dt, mark.rutland, lgirdwood,
linux-kernel, devicetree, baolin.wang, baolin.wang, erick.chen,
linux-kernel
The patch
regulator: sc2731: Add regulator driver to support Spreadtrum SC2731 PMIC
has been applied to the regulator tree at
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator.git
All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.
You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.
If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.
Please add any relevant lists and maintainers to the CCs when replying
to this mail.
Thanks,
Mark
>From 433c9bb77b8131ef340148565996b3818fbf2f23 Mon Sep 17 00:00:00 2001
From: Erick Chen <erick.chen@spreadtrum.com>
Date: Tue, 5 Dec 2017 14:35:46 +0800
Subject: [PATCH] regulator: sc2731: Add regulator driver to support Spreadtrum
SC2731 PMIC
Add regulator driver for Spreadtrum SC2731 device.
It has 17 general purpose LDOs, BUCKs generator and
digital output to control regulators.
Signed-off-by: Erick Chen <erick.chen@spreadtrum.com>
Reviewed-by: Baolin Wang <baolin.wang@spreadtrum.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
---
drivers/regulator/Kconfig | 7 +
drivers/regulator/Makefile | 1 +
drivers/regulator/sc2731-regulator.c | 256 +++++++++++++++++++++++++++++++++++
3 files changed, 264 insertions(+)
create mode 100644 drivers/regulator/sc2731-regulator.c
diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index 96cd55f9e3c5..b27417ca188a 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -744,6 +744,13 @@ config REGULATOR_S5M8767
via I2C bus. S5M8767A have 9 Bucks and 28 LDOs output and
supports DVS mode with 8bits of output voltage control.
+config REGULATOR_SC2731
+ tristate "Spreadtrum SC2731 power regulator driver"
+ depends on MFD_SC27XX_PMIC || COMPILE_TEST
+ help
+ This driver provides support for the voltage regulators on the
+ SC2731 PMIC.
+
config REGULATOR_SKY81452
tristate "Skyworks Solutions SKY81452 voltage regulator"
depends on MFD_SKY81452
diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
index 80ffc57a9ca3..19fea09ba10a 100644
--- a/drivers/regulator/Makefile
+++ b/drivers/regulator/Makefile
@@ -95,6 +95,7 @@ obj-$(CONFIG_REGULATOR_RT5033) += rt5033-regulator.o
obj-$(CONFIG_REGULATOR_S2MPA01) += s2mpa01.o
obj-$(CONFIG_REGULATOR_S2MPS11) += s2mps11.o
obj-$(CONFIG_REGULATOR_S5M8767) += s5m8767.o
+obj-$(CONFIG_REGULATOR_SC2731) += sc2731-regulator.o
obj-$(CONFIG_REGULATOR_SKY81452) += sky81452-regulator.o
obj-$(CONFIG_REGULATOR_STM32_VREFBUF) += stm32-vrefbuf.o
obj-$(CONFIG_REGULATOR_STW481X_VMMC) += stw481x-vmmc.o
diff --git a/drivers/regulator/sc2731-regulator.c b/drivers/regulator/sc2731-regulator.c
new file mode 100644
index 000000000000..794fcd504b3d
--- /dev/null
+++ b/drivers/regulator/sc2731-regulator.c
@@ -0,0 +1,256 @@
+ //SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2017 Spreadtrum Communications Inc.
+ */
+
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/of_regulator.h>
+
+/*
+ * SC2731 regulator lock register
+ */
+#define SC2731_PWR_WR_PROT_VALUE 0xf0c
+#define SC2731_WR_UNLOCK 0x6e7f
+
+/*
+ * SC2731 enable register
+ */
+#define SC2731_POWER_PD_SW 0xc28
+#define SC2731_LDO_CAMA0_PD 0xcfc
+#define SC2731_LDO_CAMA1_PD 0xd04
+#define SC2731_LDO_CAMMOT_PD 0xd0c
+#define SC2731_LDO_VLDO_PD 0xd6c
+#define SC2731_LDO_EMMCCORE_PD 0xd2c
+#define SC2731_LDO_SDCORE_PD 0xd74
+#define SC2731_LDO_SDIO_PD 0xd70
+#define SC2731_LDO_WIFIPA_PD 0xd4c
+#define SC2731_LDO_USB33_PD 0xd5c
+#define SC2731_LDO_CAMD0_PD 0xd7c
+#define SC2731_LDO_CAMD1_PD 0xd84
+#define SC2731_LDO_CON_PD 0xd8c
+#define SC2731_LDO_CAMIO_PD 0xd94
+#define SC2731_LDO_SRAM_PD 0xd78
+
+/*
+ * SC2731 enable mask
+ */
+#define SC2731_DCDC_CPU0_PD_MASK BIT(4)
+#define SC2731_DCDC_CPU1_PD_MASK BIT(3)
+#define SC2731_DCDC_RF_PD_MASK BIT(11)
+#define SC2731_LDO_CAMA0_PD_MASK BIT(0)
+#define SC2731_LDO_CAMA1_PD_MASK BIT(0)
+#define SC2731_LDO_CAMMOT_PD_MASK BIT(0)
+#define SC2731_LDO_VLDO_PD_MASK BIT(0)
+#define SC2731_LDO_EMMCCORE_PD_MASK BIT(0)
+#define SC2731_LDO_SDCORE_PD_MASK BIT(0)
+#define SC2731_LDO_SDIO_PD_MASK BIT(0)
+#define SC2731_LDO_WIFIPA_PD_MASK BIT(0)
+#define SC2731_LDO_USB33_PD_MASK BIT(0)
+#define SC2731_LDO_CAMD0_PD_MASK BIT(0)
+#define SC2731_LDO_CAMD1_PD_MASK BIT(0)
+#define SC2731_LDO_CON_PD_MASK BIT(0)
+#define SC2731_LDO_CAMIO_PD_MASK BIT(0)
+#define SC2731_LDO_SRAM_PD_MASK BIT(0)
+
+/*
+ * SC2731 vsel register
+ */
+#define SC2731_DCDC_CPU0_VOL 0xc54
+#define SC2731_DCDC_CPU1_VOL 0xc64
+#define SC2731_DCDC_RF_VOL 0xcb8
+#define SC2731_LDO_CAMA0_VOL 0xd00
+#define SC2731_LDO_CAMA1_VOL 0xd08
+#define SC2731_LDO_CAMMOT_VOL 0xd10
+#define SC2731_LDO_VLDO_VOL 0xd28
+#define SC2731_LDO_EMMCCORE_VOL 0xd30
+#define SC2731_LDO_SDCORE_VOL 0xd38
+#define SC2731_LDO_SDIO_VOL 0xd40
+#define SC2731_LDO_WIFIPA_VOL 0xd50
+#define SC2731_LDO_USB33_VOL 0xd60
+#define SC2731_LDO_CAMD0_VOL 0xd80
+#define SC2731_LDO_CAMD1_VOL 0xd88
+#define SC2731_LDO_CON_VOL 0xd90
+#define SC2731_LDO_CAMIO_VOL 0xd98
+#define SC2731_LDO_SRAM_VOL 0xdB0
+
+/*
+ * SC2731 vsel register mask
+ */
+#define SC2731_DCDC_CPU0_VOL_MASK GENMASK(8, 0)
+#define SC2731_DCDC_CPU1_VOL_MASK GENMASK(8, 0)
+#define SC2731_DCDC_RF_VOL_MASK GENMASK(8, 0)
+#define SC2731_LDO_CAMA0_VOL_MASK GENMASK(7, 0)
+#define SC2731_LDO_CAMA1_VOL_MASK GENMASK(7, 0)
+#define SC2731_LDO_CAMMOT_VOL_MASK GENMASK(7, 0)
+#define SC2731_LDO_VLDO_VOL_MASK GENMASK(7, 0)
+#define SC2731_LDO_EMMCCORE_VOL_MASK GENMASK(7, 0)
+#define SC2731_LDO_SDCORE_VOL_MASK GENMASK(7, 0)
+#define SC2731_LDO_SDIO_VOL_MASK GENMASK(7, 0)
+#define SC2731_LDO_WIFIPA_VOL_MASK GENMASK(7, 0)
+#define SC2731_LDO_USB33_VOL_MASK GENMASK(7, 0)
+#define SC2731_LDO_CAMD0_VOL_MASK GENMASK(6, 0)
+#define SC2731_LDO_CAMD1_VOL_MASK GENMASK(6, 0)
+#define SC2731_LDO_CON_VOL_MASK GENMASK(6, 0)
+#define SC2731_LDO_CAMIO_VOL_MASK GENMASK(6, 0)
+#define SC2731_LDO_SRAM_VOL_MASK GENMASK(6, 0)
+
+enum sc2731_regulator_id {
+ SC2731_BUCK_CPU0,
+ SC2731_BUCK_CPU1,
+ SC2731_BUCK_RF,
+ SC2731_LDO_CAMA0,
+ SC2731_LDO_CAMA1,
+ SC2731_LDO_CAMMOT,
+ SC2731_LDO_VLDO,
+ SC2731_LDO_EMMCCORE,
+ SC2731_LDO_SDCORE,
+ SC2731_LDO_SDIO,
+ SC2731_LDO_WIFIPA,
+ SC2731_LDO_USB33,
+ SC2731_LDO_CAMD0,
+ SC2731_LDO_CAMD1,
+ SC2731_LDO_CON,
+ SC2731_LDO_CAMIO,
+ SC2731_LDO_SRAM,
+};
+
+static const struct regulator_ops sc2731_regu_linear_ops = {
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .is_enabled = regulator_is_enabled_regmap,
+ .list_voltage = regulator_list_voltage_linear,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+ .set_voltage_sel = regulator_set_voltage_sel_regmap,
+};
+
+#define SC2731_REGU_LINEAR(_id, en_reg, en_mask, vreg, vmask, \
+ vstep, vmin, vmax) { \
+ .name = #_id, \
+ .of_match = of_match_ptr(#_id), \
+ .ops = &sc2731_regu_linear_ops, \
+ .type = REGULATOR_VOLTAGE, \
+ .id = SC2731_##_id, \
+ .owner = THIS_MODULE, \
+ .min_uV = vmin, \
+ .n_voltages = ((vmax) - (vmin)) / (vstep) + 1, \
+ .uV_step = vstep, \
+ .enable_is_inverted = true, \
+ .enable_val = 0, \
+ .enable_reg = en_reg, \
+ .enable_mask = en_mask, \
+ .vsel_reg = vreg, \
+ .vsel_mask = vmask, \
+}
+
+static struct regulator_desc regulators[] = {
+ SC2731_REGU_LINEAR(BUCK_CPU0, SC2731_POWER_PD_SW,
+ SC2731_DCDC_CPU0_PD_MASK, SC2731_DCDC_CPU0_VOL,
+ SC2731_DCDC_CPU0_VOL_MASK, 3125, 400000, 1996875),
+ SC2731_REGU_LINEAR(BUCK_CPU1, SC2731_POWER_PD_SW,
+ SC2731_DCDC_CPU1_PD_MASK, SC2731_DCDC_CPU1_VOL,
+ SC2731_DCDC_CPU1_VOL_MASK, 3125, 400000, 1996875),
+ SC2731_REGU_LINEAR(BUCK_RF, SC2731_POWER_PD_SW, SC2731_DCDC_RF_PD_MASK,
+ SC2731_DCDC_RF_VOL, SC2731_DCDC_RF_VOL_MASK,
+ 3125, 600000, 2196875),
+ SC2731_REGU_LINEAR(LDO_CAMA0, SC2731_LDO_CAMA0_PD,
+ SC2731_LDO_CAMA0_PD_MASK, SC2731_LDO_CAMA0_VOL,
+ SC2731_LDO_CAMA0_VOL_MASK, 10000, 1200000, 3750000),
+ SC2731_REGU_LINEAR(LDO_CAMA1, SC2731_LDO_CAMA1_PD,
+ SC2731_LDO_CAMA1_PD_MASK, SC2731_LDO_CAMA1_VOL,
+ SC2731_LDO_CAMA1_VOL_MASK, 10000, 1200000, 3750000),
+ SC2731_REGU_LINEAR(LDO_CAMMOT, SC2731_LDO_CAMMOT_PD,
+ SC2731_LDO_CAMMOT_PD_MASK, SC2731_LDO_CAMMOT_VOL,
+ SC2731_LDO_CAMMOT_VOL_MASK, 10000, 1200000, 3750000),
+ SC2731_REGU_LINEAR(LDO_VLDO, SC2731_LDO_VLDO_PD,
+ SC2731_LDO_VLDO_PD_MASK, SC2731_LDO_VLDO_VOL,
+ SC2731_LDO_VLDO_VOL_MASK, 10000, 1200000, 3750000),
+ SC2731_REGU_LINEAR(LDO_EMMCCORE, SC2731_LDO_EMMCCORE_PD,
+ SC2731_LDO_EMMCCORE_PD_MASK, SC2731_LDO_EMMCCORE_VOL,
+ SC2731_LDO_EMMCCORE_VOL_MASK, 10000, 1200000,
+ 3750000),
+ SC2731_REGU_LINEAR(LDO_SDCORE, SC2731_LDO_SDCORE_PD,
+ SC2731_LDO_SDCORE_PD_MASK, SC2731_LDO_SDCORE_VOL,
+ SC2731_LDO_SDCORE_VOL_MASK, 10000, 1200000, 3750000),
+ SC2731_REGU_LINEAR(LDO_SDIO, SC2731_LDO_SDIO_PD,
+ SC2731_LDO_SDIO_PD_MASK, SC2731_LDO_SDIO_VOL,
+ SC2731_LDO_SDIO_VOL_MASK, 10000, 1200000, 3750000),
+ SC2731_REGU_LINEAR(LDO_WIFIPA, SC2731_LDO_WIFIPA_PD,
+ SC2731_LDO_WIFIPA_PD_MASK, SC2731_LDO_WIFIPA_VOL,
+ SC2731_LDO_WIFIPA_VOL_MASK, 10000, 1200000, 3750000),
+ SC2731_REGU_LINEAR(LDO_USB33, SC2731_LDO_USB33_PD,
+ SC2731_LDO_USB33_PD_MASK, SC2731_LDO_USB33_VOL,
+ SC2731_LDO_USB33_VOL_MASK, 10000, 1200000, 3750000),
+ SC2731_REGU_LINEAR(LDO_CAMD0, SC2731_LDO_CAMD0_PD,
+ SC2731_LDO_CAMD0_PD_MASK, SC2731_LDO_CAMD0_VOL,
+ SC2731_LDO_CAMD0_VOL_MASK, 6250, 1000000, 1793750),
+ SC2731_REGU_LINEAR(LDO_CAMD1, SC2731_LDO_CAMD1_PD,
+ SC2731_LDO_CAMD1_PD_MASK, SC2731_LDO_CAMD1_VOL,
+ SC2731_LDO_CAMD1_VOL_MASK, 6250, 1000000, 1793750),
+ SC2731_REGU_LINEAR(LDO_CON, SC2731_LDO_CON_PD,
+ SC2731_LDO_CON_PD_MASK, SC2731_LDO_CON_VOL,
+ SC2731_LDO_CON_VOL_MASK, 6250, 1000000, 1793750),
+ SC2731_REGU_LINEAR(LDO_CAMIO, SC2731_LDO_CAMIO_PD,
+ SC2731_LDO_CAMIO_PD_MASK, SC2731_LDO_CAMIO_VOL,
+ SC2731_LDO_CAMIO_VOL_MASK, 6250, 1000000, 1793750),
+ SC2731_REGU_LINEAR(LDO_SRAM, SC2731_LDO_SRAM_PD,
+ SC2731_LDO_SRAM_PD_MASK, SC2731_LDO_SRAM_VOL,
+ SC2731_LDO_SRAM_VOL_MASK, 6250, 1000000, 1793750),
+};
+
+static int sc2731_regulator_unlock(struct regmap *regmap)
+{
+ return regmap_write(regmap, SC2731_PWR_WR_PROT_VALUE,
+ SC2731_WR_UNLOCK);
+}
+
+static int sc2731_regulator_probe(struct platform_device *pdev)
+{
+ int i, ret;
+ struct regmap *regmap;
+ struct regulator_config config = { };
+ struct regulator_dev *rdev;
+
+ regmap = dev_get_regmap(pdev->dev.parent, NULL);
+ if (!regmap) {
+ dev_err(&pdev->dev, "failed to get regmap.\n");
+ return -ENODEV;
+ }
+
+ ret = sc2731_regulator_unlock(regmap);
+ if (ret) {
+ dev_err(&pdev->dev, "failed to release regulator lock\n");
+ return ret;
+ }
+
+ config.dev = &pdev->dev;
+ config.regmap = regmap;
+
+ for (i = 0; i < ARRAY_SIZE(regulators); i++) {
+ rdev = devm_regulator_register(&pdev->dev, ®ulators[i],
+ &config);
+ if (IS_ERR(rdev)) {
+ dev_err(&pdev->dev, "failed to register regulator %s\n",
+ regulators[i].name);
+ return PTR_ERR(rdev);
+ }
+ }
+
+ return 0;
+}
+
+static struct platform_driver sc2731_regulator_driver = {
+ .driver = {
+ .name = "sc27xx-regulator",
+ },
+ .probe = sc2731_regulator_probe,
+};
+
+module_platform_driver(sc2731_regulator_driver);
+
+MODULE_AUTHOR("Chen Junhui <erick.chen@spreadtrum.com>");
+MODULE_DESCRIPTION("Spreadtrum SC2731 regulator driver");
+MODULE_LICENSE("GPL v2");
--
2.15.0
^ permalink raw reply related [flat|nested] 4+ messages in thread
* Applied "regulator: Add Spreadtrum SC2731 regulator documentation" to the regulator tree
2017-12-05 6:35 [PATCH v2 1/2] dt-bindings: regulator: Add Spreadtrum SC2731 regulator documentation Erick Chen
2017-12-05 6:35 ` [PATCH v2 2/2] regulator: sc2731: Add regulator driver to support Spreadtrum SC2731 PMIC Erick Chen
@ 2017-12-05 12:48 ` Mark Brown
1 sibling, 0 replies; 4+ messages in thread
From: Mark Brown @ 2017-12-05 12:48 UTC (permalink / raw)
To: Erick Chen
Cc: Mark Brown, broonie, robh+dt, mark.rutland, lgirdwood,
linux-kernel, devicetree, baolin.wang, baolin.wang, erick.chen,
linux-kernel
The patch
regulator: Add Spreadtrum SC2731 regulator documentation
has been applied to the regulator tree at
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator.git
All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.
You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.
If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.
Please add any relevant lists and maintainers to the CCs when replying
to this mail.
Thanks,
Mark
>From 5149b685b122d3bee78bd3403997f9ddb1223f4a Mon Sep 17 00:00:00 2001
From: Erick Chen <erick.chen@spreadtrum.com>
Date: Tue, 5 Dec 2017 14:35:45 +0800
Subject: [PATCH] regulator: Add Spreadtrum SC2731 regulator documentation
This patch adds support for the Spreadtrum SC2731
voltage regulator device.
Signed-off-by: Erick Chen <erick.chen@spreadtrum.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
---
.../bindings/regulator/sprd,sc2731-regulator.txt | 43 ++++++++++++++++++++++
1 file changed, 43 insertions(+)
create mode 100644 Documentation/devicetree/bindings/regulator/sprd,sc2731-regulator.txt
diff --git a/Documentation/devicetree/bindings/regulator/sprd,sc2731-regulator.txt b/Documentation/devicetree/bindings/regulator/sprd,sc2731-regulator.txt
new file mode 100644
index 000000000000..63dc07877cd6
--- /dev/null
+++ b/Documentation/devicetree/bindings/regulator/sprd,sc2731-regulator.txt
@@ -0,0 +1,43 @@
+Spreadtrum SC2731 Voltage regulators
+
+The SC2731 integrates low-voltage and low quiescent current DCDC/LDO.
+14 LDO and 3 DCDCs are designed for external use. All DCDCs/LDOs have
+their own bypass (power-down) control signals. External tantalum or MLCC
+ceramic capacitors are recommended to use with these LDOs.
+
+Required properties:
+ - compatible: should be "sprd,sc27xx-regulator".
+
+List of regulators provided by this controller. It is named according to
+its regulator type, BUCK_<name> and LDO_<name>. The definition for each
+of these nodes is defined using the standard binding for regulators at
+Documentation/devicetree/bindings/regulator/regulator.txt.
+
+The valid names for regulators are:
+BUCK:
+ BUCK_CPU0, BUCK_CPU1, BUCK_RF
+LDO:
+ LDO_CAMA0, LDO_CAMA1, LDO_CAMMOT, LDO_VLDO, LDO_EMMCCORE, LDO_SDCORE,
+ LDO_SDIO, LDO_WIFIPA, LDO_USB33, LDO_CAMD0, LDO_CAMD1, LDO_CON,
+ LDO_CAMIO, LDO_SRAM
+
+Example:
+ regulators {
+ compatible = "sprd,sc27xx-regulator";
+
+ vddarm0: BUCK_CPU0 {
+ regulator-name = "vddarm0";
+ regulator-min-microvolt = <400000>;
+ regulator-max-microvolt = <1996875>;
+ regulator-ramp-delay = <25000>;
+ regulator-always-on;
+ };
+
+ vddcama0: LDO_CAMA0 {
+ regulator-name = "vddcama0";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <3750000>;
+ regulator-enable-ramp-delay = <100>;
+ };
+ ...
+ };
--
2.15.0
^ permalink raw reply related [flat|nested] 4+ messages in thread
end of thread, other threads:[~2017-12-05 12:49 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2017-12-05 6:35 [PATCH v2 1/2] dt-bindings: regulator: Add Spreadtrum SC2731 regulator documentation Erick Chen
2017-12-05 6:35 ` [PATCH v2 2/2] regulator: sc2731: Add regulator driver to support Spreadtrum SC2731 PMIC Erick Chen
2017-12-05 12:48 ` Applied "regulator: sc2731: Add regulator driver to support Spreadtrum SC2731 PMIC" to the regulator tree Mark Brown
2017-12-05 12:48 ` Applied "regulator: Add Spreadtrum SC2731 regulator documentation" " Mark Brown
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).